Weslo WLTL29320 User manual

Weslo WLTL29320 User manual
Model No. WLTL29320
Serial No.
USER'S MANUAL
Serial Number
Decal
QUESTIONS?
If you have questions, or if there
are missing parts, we will guarantee complete satisfaction
through direct assistance from
our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLLFREE CUSTOMER HOT LINE.
The trained technicians on our
Customer Hot Line will provide
immediate assistance, free of
charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
www.weslo.com
new products, prizes,
fitness tips, and much more!
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING and a PART LIST are attached in the center of this manual.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
2. Use the treadmill only as described.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
10. When connecting the power cord (see page 8),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
11. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 8. To purchase a surge suppressor, see
your local WESLO or call 1-800-806-3651 and
order part number 146148.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
12. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change
speed or stop unexpectedly, which may result
in a fall and serious injury.
7. The treadmill should be used only by persons
weighing 250 pounds or less.
8. Never allow more than one person on the
treadmill at a time.
13. Keep the power cord and the surge suppressor away from heated surfaces.
2
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See BEFORE YOU BEGIN on page 4 if the treadmill
is not working properly.)
19. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
15. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
21. Never insert any object into any opening.
kg) to raise, lower, or move the treadmill.
20. Inspect and properly tighten all parts of the
treadmill regularly.
22.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.
cord immediately after use, before cleaning
the treadmill, and before performing the
maintenance and adjustment procedures described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service representative only.
17. Never leave the treadmill unattended while it
is running. Always remove the key and unplug the power cord when the treadmill is not
in use.
18. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 5, and HOW TO FOLD
AND MOVE THE TREADMILL on page 11.)
You must be able to safely lift 45 pounds (20
DANGER: Always unplug the power
23. This treadmill is intended for in-home use
only. Do not use this treadmill in a commercial, rental, or institutional setting.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. WESLO assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown have been placed on your
treadmill. If a decal is missing, or if it is not
legible, please call our Customer Service
Department, toll-free, to order a free replacement decal (see ORDERING REPLACEMENT
PARTS on the back cover of this manual).
Apply the decal in the location shown. Note:
The decals are not shown at actual size.
3
BEFORE YOU BEGIN
Congratulations for selecting the new WESLO® CADENCE C42 treadmill. The CADENCE C42 treadmill
combines advanced technology with innovative design
to help you get the most from your exercise in the convenience and privacy of your home. And when you’re
not exercising, the unique CADENCE C42 can be
folded up, requiring less than half the floor space of
other treadmills.
at 1-800-999-3756, Monday through Friday, 6 a.m. until
6 p.m. Mountain Time (excluding holidays). To help us
assist you, please note the product model number and
serial number before calling. The model number of the
treadmill is WLTL29320. The serial number can be
found on a decal attached to the treadmill (see the
front cover of this manual for the location).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are labeled.
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
please call our Customer Service Department toll-free
Bookrack
Water Bottle Holder
(Bottle not included)
Console
Key/Clip
Handrail
Upright
Storage Latch
RIGHT SIDE
Walking Belt
Foot Rail
Circuit Breaker
Power Cord
Cushioned Walking Platform
for maximum exercise comfort
BACK
Incline Leg
Rear Roller
Adjustment Bolts
4
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included small allen wrench
and your own phillips screwdriver
rubber mallet
, wire cutters
, adjustable wrenches
, and needlenose
pliers
.
,
To identify small parts during assembly, use the PART IDENTIFICATION CHART in the center of this manual.
1. Make sure that the power cord is unplugged.
1
40
87
75
40
With the help of a second person, carefully tip the
treadmill onto one side. Partially fold the Frame (75) so
that the treadmill is more stable. Do not fully fold the
treadmill until it is completely assembled.
87
Attach four Base Pads (40) to the Base (11) with two
1 1/4” Tek Screws (87) and two 3/4” Tek Screws (102) in
the locations shown.
2. With the help of a second person, tip the treadmill down
to the position shown.
102
40
11
102
2
76
Attach a Wheel (37) to each side of the Base (11) with a
Wheel Bolt (36) and a Wheel Nut (38) as shown.
Identify the Right Upright (62) and the Left Upright (76)
(there are two small holes in the side of the Left Upright).
Remove any plastic ties that are in the square holes in
the Uprights. While a second person holds the Right
Upright near the Wire Harness (21), insert the end of the
Wire Harness into the lower end of the Right Upright and
out of the upper end.
62
Holes
21
37
38
36
5
11
3. Insert a Plastic Shim (97) into each side of the post on
the right side of the Base (11). Next, orient the Right
Upright (62) as shown, and insert it into the Base. Make
sure that the Wire Harness (21) does not fall into the
Right Upright. Be careful to avoid pinching the Wire
Harness. Note: If necessary, tap the Right Upright with a
rubber mallet until it is fully seated in the Base. If the
Right Upright cannot be fully seated, remove the outer
Plastic Shim and then insert the Right Upright.
3
21
62
This hole
must be
on this side.
Attach the Right Upright (62) to the Base (11) with three
1” Bolts (8) and three Star Washers (9). Do not tighten
the Bolts yet.
Assemble the Left Upright (not shown) in the same way.
9
8
97
9
11
8
4. Hold the Crossbar (34) between the Uprights (62, 76).
Attach the Crossbar with two 2 1/2” Bolts (53) and two
5/16” Washers (57). Do not tighten the Bolts yet.
4
34
53
57
57
53
76
5. Identify the Right Handrail (47), which has a large hole in
the left side. Feed the Wire Harness (21) up into the rectangular bracket on the Right Handrail and out the large
hole in the left side. Note: It may be helpful to use
needlenose pliers to pull the Wire Harness out of the
large hole.
62
5
8
1
Ground
Wire
96
Remove any plastic ties that are in the rectangular
bracket on the Right Handrail (47). Insert the bracket into
the top of the Right Upright (62). Attach the upper and
lower ends of the Right Handrail to the Right Upright with
two 1” Bolts (8). Do not tighten the Bolts yet.
Large
Hole
8
47
76
Bracket
Attach the Left Handrail (1) as described above. Note:
There is not a wire harness on the left side.
Attach the end of the ground wire to the small hole in the
side of the Right Handrail (47) with a Silver Ground
Screw (96).
62
8
8
6
21
6. Place the Console Base (46) on the Right Handrail (47)
and the Left Handrail (not shown). Touch the Right
Upright (62) to discharge any static.
6
Hold the Console (10) near the Console Base (46). Insert
the Wire Harness (21) through the two indicated plastic
ties on the Console Base. Next, insert the Wire Harness
up through the indicated opening in the Console Base
and through the plastic tie on the bottom of the Console.
Plug the widest connector on the Wire Harness (21) into
the widest connector on the Console (10). If the connector does not fit easily, rotate it and then connect it.
Plug the other connector on the Wire Harness into the
other connector on the Console. Note: The locations of
the connectors are shown by arrows.
10
Tie
21
46
47
Ties
21
Securely tighten the plastic tie on the Console (10) to
prevent the Wire Harness (21) from slipping. Then, cut
off the end of the plastic tie.
7. Set the Console (10) in the Console Base (46). Be careful
to avoid pinching any wires. Insert the excess Wire
Harness (21) into the large hole in the side of the Right
Handrail (47). Securely tighten the plastic ties on the
bottom of the Console Base to prevent the Wire
Harness from slipping. Cut off the ends of the plastic ties.
Attach the Console (10) to the Console Base (46) with
seven 3/4” Screws (13). Make sure that no wires are
pinched. Start all seven Screws before tightening
them; do not overtighten the Screws.
62
7
46
10
1
Ties
13
21
13
47
13
Attach the Console Base (46) to the Left and Right
Handrails (1, 47) with four 3/4” Screws (13).
8. Attach the Storage Latch (14) to the left Upright (76) with
two 3/4” Screws (13). Be careful not to overtighten the
Screws.
Lift the treadmill frame (see HOW TO FOLD THE
TREADMILL FOR STORAGE on page 11), but do not
latch it. Make sure that the frame is centered between
the Handrails (1, 47 [not shown]). Firmly tighten all of
the bolts and screws used in assembly steps 3, 4,
and 5. Then, lower the frame to the floor.
8
1
76
14
13
9. Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may
be included. Keep the included allen wrenches in a secure place. The large allen wrench is used to adjust the
walking belt (see page 13). To protect the floor or carpet, place a mat under the treadmill.
7
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBETM WALKING BELT
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking platform. Such substances will deteriorate the walking
belt and cause excessive wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
HOW TO PLUG IN THE POWER CORD
DANGER: Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local WESLO dealer or call toll-free 1-800-8063651 and order part number 146148.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated
for 120 volts AC and 15 amps. There must be a
monitoring light on the surge suppressor to indicate whether it is functioning properly. Failure to
use a properly functioning surge suppressor could
result in damage to the control system of the
treadmill. If the control system is damaged, the
walking belt may change speed or stop unexpectedly, which may result in a fall and serious injury.
Surge Suppressor
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having
8
CONSOLE DIAGRAM
Displays
Heart Rate
Sensor
Note: If there is a thin sheet of
plastic on the console, remove it.
Insert the key fully into the console. After a moment,
the displays will light. Test the clip by carefully taking a few steps backward until the key is pulled
from the console. If the key is not pulled from the
console, adjust the position of the clip.
CAUTION: Before operating the
console, read the following precautions.
• Do not stand on the walking belt when turning on the power.
Follow the steps below to operate the console.
• Always wear the clip (see the drawing
below) while operating the treadmill.
1
• Adjust the speed in small increments to
avoid sudden jumps in speed.
Insert the key fully into the console.
A few seconds after the key is inserted, the displays will light.
• To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console and place only a sealed
water bottle in the water bottle holder.
2
Press the Speed ▲ button to start the walking
belt.
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
STEP-BY-STEP CONSOLE OPERATION
As you exercise, change the speed of the walking
belt as desired by pressing the Speed buttons.
Each time a button is pressed, the speed setting
will change by 0.1 mph; if a button is held down,
the speed setting will change in increments of 0.5
mph. Note: The console can display speed and
distance in either miles or kilometers (see
SPEED DISPLAY on page 10). For simplicity, all
instructions in this section refer to miles.
Before operating the console, make sure that the
power cord is properly plugged in (see page 8).
Next, stand on the foot
rails of the treadmill.
Find the clip attached to
the key, and slide the
clip onto the waistband
of your clothes.
Clip
Key
9
To stop the walking belt, press the Stop button.
The Time/Distance display will begin to flash.
“E” for English miles or an “M” for metric kilometers
will appear in the Fat Calories/Calories/Pulse display. Press the Speed ▲ button to change the unit
of measurement. When the desired unit of measurement is selected, remove the key and then
reinsert it.
Note: During the first few minutes that the treadmill
is used, inspect the alignment of the walking belt,
and align it if necessary (see page 13).
3
To reset the displays, press the Stop button, remove the key, and then reinsert the key.
Change the incline of the treadmill as desired.
To change the incline of the treadmill, press either
of the Incline buttons until the desired incline level
is reached.
4
5
Measure your heart rate, if desired.
To measure your
heart rate, stand on
the foot rails and
place your thumb
on the heart rate
sensor. Do not
press too hard, or
the circulation in
your thumb will be restricted and your pulse
will not be detected. After a few seconds, the
heart-shaped indicator in the Fat Calories/Calories/
Pulse display will begin to flash, one or two dashes
(– –) will appear, and then your heart rate will be
shown. Hold your thumb on the heart rate sensor
for about 15 seconds for the most accurate reading.
Follow your progress with the three displays.
Time/Distance
Mode Indicator
display—This display
shows the elapsed time
and the distance that
you have walked or run.
The display will change
from one number to the
other every few seconds, as shown by the mode
indicators. When the Stop button is pressed, the
display will flash.
Fat Calories/Calories/
Pulse display—This
display shows the approximate numbers of
fat calories and calories
you have burned (see
FAT BURNING on page 14). The display will
change from one number to the other every few
seconds, as shown by the mode indicators. The
display will also show your heart rate when you
use the heart rate sensor (see step 5).
If the displayed heart rate appears to be too high
or too low, or if your heart rate is not displayed, lift
your thumb off the heart rate sensor for a few seconds. Then, place your thumb on the heart rate
sensor as described above. Remember to stand
still while measuring your heart rate.
6
Speed display—This
display shows the speed
of the walking belt
When you are finished exercising, remove the
key.
Step onto the foot rails, press the Stop button, and
remove the key from the console. Keep the key in a
secure place.
WARNING:
Note: The console can
display speed and distance in either miles or
kilometers. To change
the unit of measurement, hold down the
Stop button, insert the key into the console, and
continue to hold the Stop button for a moment. An
Removing the key
does not cut off power to the incline system. To prevent movement of the treadmill
and possible injury, unplug the power cord
when the treadmill is not in use.
10
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
1
Before folding the treadmill, unplug the power cord. CAUTION:
You must be able to safely lift 45 pounds (20 kg) in order to
raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown at
the right. To decrease the possibility of injury, bend your
legs and keep your back straight. As you raise the treadmill, make sure to lift with your legs rather than your
back. Raise the treadmill about halfway to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Press out on the storage latch. Raise the
treadmill until the storage latch closes over the catch. Make
sure that the storage latch is fully engaged over the
catch.
To protect the floor or carpet from damage, place a mat
under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the storage
position in temperatures above 85° Fahrenheit.
2
Engaged
Storage
Latch
Catch
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage
position as described above. Make sure that the storage latch
is fully engaged over the catch.
1. Hold the upper ends of the handrails. Place one foot on the
base as shown.
2. Tilt the treadmill back until it rolls freely on the front wheels.
Carefully move the treadmill to the desired location. To reduce the risk of injury, use extreme caution while moving the treadmill. Do not move the treadmill over an uneven surface.
Base
3. Place one foot on the base, and carefully lower the treadmill
until it is resting in the storage position.
Front Wheels
HOW TO LOWER THE TREADMILL FOR USE
1. See drawing 2 above. Hold the upper end of the treadmill with your right hand as shown. Press the storage
latch and hold it. Pivot the treadmill until the frame and foot rail are past the storage latch.
2. See drawing 1 above. Hold the treadmill firmly with both hands, and lower the treadmill to the floor. Do not
drop the treadmill frame to the floor. To decrease the possibility of injury, bend your legs and keep
your back straight.
11
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department tollfree at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 8). Use only a single-outlet surge suppressor
that meets all of the specifications described on page 8. Important: The treadmill is not compatible
with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the treadmill
frame near the power cord. If the switch protrudes
as shown, the circuit breaker has tripped. To reset
the circuit breaker, wait for five minutes and then
press the switch back in.
c
Reset
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing
above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five
minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. If the treadmill still will not run, please call our Customer Service Department, toll-free.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. Remove the screws from
the hood, and carefully remove the hood.
Locate the Reed Switch (44) and the Magnet (45) on
the left side of the Pulley (50). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 1/8”. If necessary, loosen the Reed
Switch Screw (103) and move the Reed Switch
slightly. Retighten the Screw. Re-attach the hood, and
run the treadmill for a few minutes to check for a correct speed reading. Reattach the Resistance Knob.
12
a
44
1/8”
50
45
103
Top
View
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 8.
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE
POWER CORD. Using the allen wrench, turn both
rear roller adjustment bolts counterclockwise, 1/4 of a
turn. When the walking belt is properly tightened, you
should be able to lift each side of the walking belt 2 to
3 inches off the walking platform. Be careful to keep
the walking belt centered. Plug in the power cord, insert the key and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
b
2”–3”
Rear Roller Adjustment Bolts
c. If the walking belt still slows when walked on, please call our toll-free Customer Service
Department.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the key
and UNPLUG THE POWER CORD. If the walking
belt has shifted to the left, use the allen wrench to
turn the left rear roller bolt clockwise 1/2 of a turn; if
the walking belt has shifted to the right, turn the
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Plug in the power cord,
insert the key and run the treadmill for a few minutes.
Repeat until the walking belt is centered.
b. If the walking belt slips when walked on, first remove
the key and UNPLUG THE POWER CORD. Using
the allen wrench, turn both rear roller bolts clockwise,
1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each side of the walking belt 2 to 3 inches off the walking platform. Be
careful to keep the walking belt centered. Plug in the
power cord, insert the key and carefully walk on the
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
13
a
b
CONDITIONING GUIDELINES
WARNING:
Before beginning this
or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with preexisting health problems.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
The following guidelines will help you to plan your exercise program. For more detailed exercise information, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recommended heart rates for fat burning and aerobic exercise.
uses easily accessible carbohydrate calories for energy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the treadmill until your heart rate is near the lowest number in
your training zone.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
Aerobic Exercise
If your goal is to strengthen your cardiovascular system, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up increases your body temperature, heart rate and circulation in preparation for exercise.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “training zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
To measure your heart rate during exercise, use the
pulse sensor. If your heart rate is too high or too low,
adjust the speed and incline of the treadmill.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
A Cool-down—Finish each workout with 5 to 10 minutes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent postexercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months, you may complete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
14
SUGGESTED STRETCHES
1
The correct form for several basic stretches is shown at the right.
Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees, and
back.
2
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot toward
you and rest it against the inner thigh of your extended leg. Reach
toward your toes as far as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Hamstrings, lower back,
and groin.
3
3. Calf/Achilles Stretch
4
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat 3
times for each leg. To cause further stretching of the achilles tendons, bend your back leg as well. Stretches: Calves, achilles tendons, and ankles.
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your buttocks as possible. Hold for 15 counts, then relax. Repeat 3 times for
both legs. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward. Pull
your feet toward your groin area as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Quadriceps and hip
muscles.
15
5
ORDERING REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). When ordering parts, please be prepared to give
the following information:
• The MODEL NUMBER of the product (WLTL29320)
• The NAME of the product (WESLO® CADENCE C42 treadmill)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED DRAWING in the center of this manual)
WESLO is a registered trademark of ICON Health & Fitness, Inc.
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repairing, at ICON's option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be pre-authorized by ICON. This warranty does not
extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON authorized service center; products used for commercial or rental purposes; or products used as store display models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 186970 R0902A
Printed in USA © 2002 ICON Health & Fitness, Inc.
PART IDENTIFICATION CHART
Remove this chart and use it to identify small parts during assembly. Save
this chart and the EXPLODED DRAWING/PART LIST for future reference.
Silver Ground
Screw (96)–1
3/4” Screw (13)–13
3/4” Tek Screw
(102)–2
1 1/4” Tek Screw (87)–2
1” Bolt (8)–10
2 1/2” Bolt (53)–2
Wheel Bolt (36)–2
5/16” Washer (57)–2
Star Washer (9)–6
(May be an internal Star Washer)
Wheel Nut (38)–2
PART LIST—Model No. WLTL29320
Key
No.
Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20*
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
1
1
2
1
1
1
1
10
1
1
1
1
15
1
1
7
3
1
1
1
1
4
1
1
23
1
1
1
1
1
2
1
2
1
8
2
2
4
5
4
2
1
1
1
1
1
1
4
2
1
1
2
2
1
1
1
Description
Left Handrail
Key/Clip
Incline Leg Pivot Bolt
Cover
Left Foot Rail
Lift Motor
Rear Roller
1” Bolt
Star Washer
Console Insert
Base
Motor Belt
3/4” Screw
Storage Latch
Thin Frame Spacer
8” Cable Tie
Motor Nut
Pulley/Flywheel/Fan
Motor
Motor/Pulley/Flywheel/Fan
Wire Harness
Belt Guide Screw
Motor Hood
Hood Shield
Screw
Controller
Motor Swivel Bolt
Motor Tension Nut
Motor Star Washer
Motor Tension Washer
Motor Tension Bolt
Incline Stop Bracket
Insert Nut
Crossbar
Cage Nut
Wheel Bolt
Wheel
Wheel Nut/Lift Nut
Washer
Base Pad
Base Endcap
Latch Catch
Reed Switch Clip
Reed Switch
Magnet
Console Base
Right Handrail
Platform Screw
Isolator
Front Roller/Pulley
Front Roller Adj. Bolt
Incline Wheel
2 1/2” Bolt
Power Cord
Power Cord Grommet
Circuit Breaker
Key
No.
Qty.
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
#
#
#
#
#
4
2
1
1
2
1
3
1
2
2
1
1
1
12
1
1
2
1
1
1
2
1
4
1
2
1
2
1
1
1
2
1
1
1
4
1
1
1
2
1
4
1
1
1
1
2
1
1
1
1
1
1
1
R0902A
Description
5/16” Washer
Frame Pivot Bolt
Latch Decal
Motor Belly Pan
Cable Tie Clamp
Right Upright
Releasable Tie
Choke
Belt Guide
Belly Pan Fastener
Walking Belt
Walking Platform
Belly Pan
Electronics Screw
Incline Wire Harness
Upright Grommet
Small Screw
5/32” Allen Wrench
Frame
Left Upright
Incline Wheel Bolt
Power Supply Plate
Incline Wheel Nut
Ground Wire
Hood Screw (Front)
Incline Leg
Rear Roller Adj. Bolt
Left Rear Endcap
Right Rear Endcap
Incline Motor Bolt
1 1/4” Tek Screw
Power Supply
Motor Belt Shield
Bookrack
Plastic Stand-off
Warning Decal
Right Foot Rail
Silver Screw
Plastic Tie
Silver Ground Screw
Shim
Thin Frame Spacer
Hole Plug
Motor Controller Wire
Allen Wrench
3/4” Tek Screw
Reed Switch Screw
Incline Warning Decal
4” Blue Wire, 2F
8” Blue Wire, 2F
4” White Wire, M/F
8” White Wire, 2F
User’s Manual
* Includes all parts shown in the box
# These parts are not illustrated
31
84
6
39
86
83
17
32
101
83
74
17
39
7
48
77
85
75
5
100
13
52
13
42
4
46
3
92
80
73
49
79
13
13
104
66
90
79
82
59
71
13
25
48
10
95
52
3
77
16
87
98 38
93
48
13
25
69
45
68
44
66
67
50
2
49
22
43
63
25
39
25
103
60
87
40
65
39
48
61
73
1
25
36
51
14
41
37
97
38
8
35
15
57
35
57
39
25
9
38
40
8
58
102
35
13
33
76
53
25
31 30
27
8
13
9
25
41
11
8
29
38
64
28
12
34
17
19
87
40
102
40
70
13
18
20*
25
72
36
37
78
91
70
89
25
94 57
23
58
70
88
26
54
70
24
21
55
8
56
9
35
8
47
25
33
62
97
35
99
96
8
53
57
8
25
13
35
9
81
EXPLODED DRAWING—Model No. WLTL29320
R0902A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement