Westinghouse MT80A TILT Installation Sheet

Installation and Assembly:

Universal Tilt Wall Mount for 15" - 37" Screens

Model: MT80A TILT

Features:

• Fits 15" to 37" flat panel screens

• One-touch tilt for effortless positioning and adjustment of the screen

Visit the Westinghouse Web Site at www.westinghousedigital.com

R

This product is intended for use with UL

Listed products and must be installed by a qualified professional installer.

Max UL Load Capacity: 80 lb (36.3 kg)

For customer care call 1-866-287-5555.

ISSUED: 01-17-06 SHEET #: 202-9091-1

Note: Read entire instruction sheet before you start installation and assembly.

WARNING

• Do not begin to install your Westinghouse product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call customer care at 1-866-287-5555.

• This product should only be installed by a qualified professional.

• Make sure that the wall will safely support the combined load of the equipment and all attached hardware and components.

• Never exceed the Maximum UL Load Capacity of 80 lb (36.3 kg).

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an

"edge to edge" stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power.

Tools Needed for Assembly

• stud finder ("edge to edge" stud finder is recommended)

• phillips screwdriver

• drill

• 1/4" bit for concrete and cinder block wall

• 1/2" bit for metal stud wall

• 5/32" bit for metal or wood stud wall

• level

Accessories

• Metal Stud Fastener Kit (ACC 215) (Not evaluated by UL)

• Video Conferencing Shelf (ACC 309) (Not evaluated by UL)

• Accessory Shelves (PM 600, PM 610) (Not evaluated by UL)

Table of Contents

Parts List .............................................................................................................................................................................. 3

Installation to Single Wood Stud Wall ................................................................................................................................... 4

Installation to Solid Concrete or Cinder Block ....................................................................................................................... 5

Attaching Adapter Plate to Flat Panel Screen ...................................................................................................................... 6

Installing and Removing Flat Panel Screen ........................................................................................................................... 7

Adjusting the Tilt Angle of the Flat Panel Screen .................................................................................................................. 7

For customer care call 1-866-287-5555.

2 of 8 ISSUED: 01-17-06 SHEET #: 202-9091-1

Parts List

Description

A adapter plate

B tilt assembly

C Alligator® anchor

D M4 x 10 mm phillips screw

E M4 x 20 mm phillips screw

F retaining spacer

G #14 x 2-1/2" hex head wood screw

H M5 x 6 mm screw

1 095-4346

1 095-0360

2 590-0097

4 504-9012

4 504-9020

4 590-5005

2 5S1-015-C03

1 520-1023

A

B

C D E

3 of 8

F G H

ISSUED: 01-17-06 SHEET #: 202-9091-1

Installation to Single Wood Stud Wall

WARNING

• Make sure that the wall will safely support the combined load of the equipment and all attached hardware and components.

1 Use a stud finder to locate the edges of the stud. Use of an edge-to-edge stud finder is highly recommended. Based on its edges, draw a vertical line down the stud’s center. Place tilt assembly (B) on wall as a template, making sure that the two mounting holes are over the stud centerline. Level tilt assembly, and mark the center of the two holes.

Drill two 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the tilt assembly is level, secure it using two

#14 x 2-1/2" wood screws (G) as shown.

Skip to step 2 on page 6.

WARNING

• Tighten wood screws so that tilt assembly is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers are responsible to provide hardware for other types of mounting situations.

G

B

4 of 8 ISSUED: 01-17-06 SHEET #: 202-9091-1

Installation to Solid Concrete or Cinder Block

WARNING

• When installing Westinghouse wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the wall will safely support the combined load of the equipment and all attached hardware and components.

1 Make sure that tilt assembly (B) is level, use it as a template to mark two mounting holes. Drill two 1/4"

(6 mm) dia. holes to a minimum depth of 2-1/2"

(64 mm). Insert anchors (C) in holes flush with wall as shown (right). Place tilt assembly over anchors and secure with two #14 x 2-1/2" screws (G). Level, then tighten all fasteners.

1

concrete surface

C

Drill holes and insert anchors (C).

2

WARNING

• Tighten screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

B

G C

Place assembly (B) over anchors (C) and secure with screws (G).

3

WARNING

• Always attach concrete expansion anchors directly to load-bearing concrete.

• Never attach concrete expansion anchors to concrete covered with plaster, drywall, or other finishing material. If mounting to concrete surfaces covered with a finishing surface is unavoidable, the finishing surface must be counterbored as shown below. Be sure concrete anchors do not pull away from concrete when tightening screws. If plaster/drywall is thicker than 5/8", custom fasteners must be supplied by installer.

Tighten all fasteners.

SOLID

CONCRETE

CINDER BLOCK

C

CORRECT INCORRECT B concrete wall plate wall plate concrete plaster/ dry wall plaster/ dry wall

G

5 of 8 ISSUED: 01-17-06 SHEET #: 202-9091-1

Attaching Adapter Plate to Flat Panel Screen

WARNING

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail.

2 FOR VESA ® 75 MOUNTING PATTERN:

Choose hole pattern as shown below. Attach adapter plate (A) to back of screen using four M4 x 10 mm screws (D) as shown below.

*Note: If hole pattern is in a pocket, attach adapter plate (A) to back of screen using four M4 x 20 mm screws (E) and four retaining spacers (F) as indicated below.

FOR VESA 100 MOUNTING PATTERN:

Choose hole pattern as shown below. Attach adapter plate (A) to back of screen using four M4 x 10 mm screws (D) as shown below.

A

D

*For screens with a hole

pattern in a pocket, spacers (F) go between adapter plate (A) and screen.

F

D

A

6 of 8 ISSUED: 01-17-06 SHEET #: 202-9091-1

Installing and Removing Flat Panel Screen

3 Attach screen to tilt assembly (B). Tighten M5 x 6 mm screw (H) to lock screen to tilt assemby.

Note: For security models, use security driver (I) to tighten M5 x 6 mm screws (H).

To remove screen from mount, loosen screw (H) and lift screen off of mount.

WARNING

• Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely handle placement of the screen.

• Failure to lock adapter plate (A) with screw (H) can cause screen to come off mount if hit accidentally.

CAUTION

• Do not tighten screws with excessive force.

Overtightening can cause damage to mount. Tighten screws to 20 in. • lb (2.26 N.M.) maximum torque.

Adjusting the Tilt Angle of the Flat Panel Screen

4 Adjust tension knob on right side of mount shown in figure 4 to desired tension to balance your screen size and weight.

Note: If knob is inaccessible, remove screen from mount, adjust tension knob to desired tension to balance your screen size and weight, and reattach screen to mount as stated in step 3.

Push or pull from top or bottom of screen to adjust tilt as shown in figure 4. The tilt can be adjusted to a maximum of 15° forward or 5° backward.

CAUTION

• Do not tighten screws with excessive force.

Overtightening can cause damage to mount. Tighten screws to 40 in. • lb (4.5 N.M.) maximum torque.

CAUTION

• Be careful not to pinch fingers when pushing screen from the bottom.

SCREEN

B

fig. 4

H

A

fig. 3

TENSION KNOB

7 of 8 ISSUED: 01-17-06 SHEET #: 202-9091-1

Limited Five-Year Warranty

Westinghouse Digital Electronics warrants to original end-users of this Westinghouse display mounting product (the

“Product”) that the Product will be free from defects in material and workmanship, under normal use, for a period of five (5) years from the date of purchase by the original end-user, subject to the following terms and conditions:

REPAIR OR REPLACEMENT – For a period of five (5) years from the original date of purchase, Westinghouse Digital

Electronics will repair any defect in material or workmanship in the Product, or, at its option, replace a defective Product.

Replacement parts and products will be warranted for either the remainder of the original warranty period or ninety (90) days from the date of delivery to the end-user, whichever occurs last.

OBTAINING WARRANTY SERVICE – To obtain warranty services, you must either personally deliver or ship the Product to Westinghouse Digital Electronics, freight prepaid. Please call Westinghouse Digital Electronics at (866) 287-5555 to obtain a Return Merchandise Authorization (“RMA”) and for other instructions regarding return and replacement or repair of the Product. Westinghouse Digital Electronics will not accept Products delivered to it without an RMA.

EXCLUSIONS TO WARRANTY – This warranty does not cover damage caused by (a) service or repairs by anyone other than personnel authorized by Westinghouse Digital Electronics, (b) the failure to utilize proper packing when returning the product, (c) improper installation or the failure to follow Product instructions or warnings, or (d) misuse or accident, in transit or otherwise.

PROOF OR ORIGINAL PURCHASE – A sales receipt, invoice, or other proof of purchase specifying the original date of purchase within the five (5) year warranty period must be presented to obtain warranty service. This warranty extends to the original purchaser and is not transferable.

EITHER REPAIR OR REPLACEMENT IS YOUR EXCLUSIVE REMEDY UNDER THIS WARRANTY. EXCEPT TO THE

EXTENT PROHIBITED BY LAW, WESTINGHOUSE DIGITAL SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR

CONSEQUENTIAL DAMAGES CLAIMED TO ARISE FROM BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON

THIS PRODUCT. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE

ON THIS PRODUCT IS LIMITED IN DURATION AND SCOPE TO THE TERMS OF THIS WARRANTY.

Some States do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives specific legal rights, and you may also have other rights which vary from State to State.

Westinghouse Digital Electronics, LLC

12150 Mora Drive

Santa Fe Springs, CA 90670

Tel. (562) 236-9800

Fax. (562) 236-9898

8 of 8 ISSUED: 01-17-06 SHEET #: 202-9091-1 and Westinghouse are trademarks of Westinghouse Electric Corporation and are used under license.