Westinghouse | WST1800 | User's Manual | Westinghouse WST1800 User's Manual

Westinghouse WST1800 User's Manual
™
SweepEZE
WST1800 Automatic Vacuuming Dust Bin
IMPORTANT SAFETY INSTRUCTIONS
This electrical appliance must always be used according to the following safety instructions.
Save these instructions as this manual contains important safety and operating information.
When using an electrical appliance, basic precautions should always be followed, including
the following:
READ ALL INSTRUCTIONS CAREFULLY BEFORE USING THIS APPLIANCE
WARNING: To reduce the risk of fire, electric shock or injury:
1. Always turn Control Dial to the OFF position before unplugging SweepEZE™
.
2. Always unplug the appliance before cleaning or servicing it. Do not unplug by pulling the
cord; to unplug, grasp the plug, not the cord.
3. Do not let the SweepEZE™ be used as a toy. Close attention is necessary when used
near children. Do not use in AUTO Mode or leave appliance plugged in near small children
or infants.
4. Do not pull or carry the appliance by the cord. Do not run the appliance over the cord, close a
door on the cord, or pull the cord around sharp edges or corners. Keep the cord away from
heated surfaces.
5. Do not use the appliance if the cord or plug is damaged.
6. Avoid the use of extension cords.
7. Do not handle the plug or appliance with wet hands.
8. Do not use appliance outdoors, or on wet surfaces.
9. Do not use appliance to dispose of water or damp materials such as mud, tile grout, plaster
filler, or caulking. Do not use to pick up any liquid or wet objects.
10. Do not use appliance to vacuum up flammable or combustible liquids, such as gasoline. Do
not use in areas where these liquids may be present.
11. Do not use this appliance to vacuum up burning or smoking materials, such as cigarettes,
matches or hot ashes.
12. Keep hair, loose clothing, and all parts of the body, especially fingers, away from openings
and moving parts.
13. Do not put any objects into appliance openings, or use with any openings blocked or plugged.
14. Do not use this appliance to pick up hard or sharp objects or other large surface litter. Pick
these up by hand before vacuuming.
15. Do not operate without the Collection Bin properly in place.
16. Use the appliance only for normal household use, as described in this Use and Care Guide.
17. Turn appliance off before removing or replacing the Collection Bin or Filter.
18. Unplug appliance before cleaning or maintenance.
19. If the appliance is not working as it should, call 1-800-616-8689 for instructions where to
send for repair. Do not attempt to repair, as it will invalidate your warranty.
20. When cleaning the outside of the appliance, wipe with a damp cloth to reduce the static
electricity on the outer surface.
SAVE THESE INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
1
SweepEZE™
AUTOMATIC VACUUMING DUST BIN
WESTINGHOUSE
Product may vary slightly from illustrations
Status Indicator Light
Collection Bin Cover
(not shown)
AUTO/OFF/MANUAL
Control Dial
Cord Storage
(on back of unit,
not shown)
Collection Bin
Fill Level Window
Collection Bin
Manual
Activation
Button
Micro Exhaust Filter Holder
and Filter
Dirt Inlet
Figure 1
Collection Bin
Lid Handle
Polarized Plug
This appliance has a
polarized plug (one blade
is wider than the other).
To reduce the risk of
electric shock, this plug is
intended to fit into a
polarized outlet only one
way. If the plug does not
fit fully in the outlet,
reverse the plug. If it still
does not fit, contact a
qualified electrician. Do
not attempt to modify the
plug in any way.
Collection
Bin Lid
Eye-Vac™ Sensors
Dirt Filter
Filtered
Air Inlet
Dirt Inlet
Figure 2
2
BEFORE USING FOR THE FIRST TIME
1. Remove SweepEZE™ from packaging and
set upright on any non-carpeted flooring.
Remove packing tape from Micro Exhaust
Filter on the side of the unit.
2. Plug unit into any standard 120V AC
electrical outlet.
3. Turn Control Dial to the MAN position for
manual operation or to the AUTO position for
automated use. The Status Indicator Light will
illuminate when the Control Dial is in either of
these positions.
Your SweepEZE™ is now ready for use.
OPERATING INSTRUCTIONS
NOTE: SweepEZE™ cannot operate when the
Control Dial is in the OFF position.
1. Turn the Control Dial to the MAN position
for manual operation or to the AUTO
position for automated use. The Status
Indicator Light will illuminate when the
Control Dial is in either of these positions.
2. In the MANUAL Mode, sweep debris
towards the Inlet at the Base of the unit,
press the Manual Activation Button and let
SweepEZE™ vacuum the debris through the
Inlet and into the Collection Bin.
3. When the Control Dial is turned to the AUTO
position, sweep debris towards the Inlet at
the Base of the unit and the Eye-Vac™
Sensors will detect the debris and
automatically initiate a timed vacuuming
cycle which will terminate 5 seconds after
the Eye-Vac™ Sensors no longer detect
debris. SweepEZE™ will vacuum the debris
through the Inlet and into the Collection Bin
without you ever having to bend over or
touch the dirt.
3
WST1800 Automatic Vacuuming Dust Bin
4. Use the Manual Activation Button to
begin vacuuming in either the MANUAL
or AUTO Modes.
5. As dirt and debris accumulate, the
Collection Bin Fill Level Window will
allow you to see when the Collection
Bin needs to be emptied and cleaned.
USER MAINTENANCE INSTRUCTIONS
Health Tip
If you suffer from allergies or asthma, take the
Collection Bin outdoors to empty. As you empty
the dirt into the trash can, gently tap the
Collection Bin against the side of the can to
remove loose debris.
Main Unit
Collection Bin
Cavity
Cleaning The Dirt Filter
Collection Bin
Lid Handle
To maintain optimal performance, the Dirt Filter
will need cleaning whenever the suction is not
strong. The Dirt Filter must be clean and free of
elements which might hinder the flow of air.
Collection
Bin Grip
Filtered Air Inlet
Figure 3
1. To empty the SweepEZE Collection Bin, turn the
Control Dial to the OFF position.
2. Pull the Collection Bin outward from the front
of the Bin Cavity. Grasp the Collection Bin Grip
firmly and lift it out and away from the
SweepEZE™ Main Unit.
3. Holding the Collection Bin firmly with one
hand, grasp the Collection Bin Lid Handle with
the other hand and pull the the Lid
Dirt Inlet
straight up and out to remove.
4. Turn the Collection Bin upside down over
a trash can. Make sure you empty all dirt and
debris from inside and below the Bin. To ensure
that all the dirt spills out, tap the side of the
Collection Bin gently against the edge of the
trash can. Re-attach the Collection Bin Lid to
the top of the Collection Bin.
5. Clean Sensors, Dirt Inlet area and Collection
Bin Cavity with a damp rag or towel.
6. Insert the assembled Collection Bin with Lid
fitted snugly into position bottom-first into the
Collection Bin Storage Cavity at the front of the
SweepEZE™. The 2 grooves in the bottom of the
Bin fit easily over the rod in the front of the
unit. Grasp the Collection Bin Grip and lock the
Collection Bin back into position.
Dirt Filter
Figure 4
1. Remove the Collection Bin and the Lid from
the unit. Locate the Dirt Filter inside the
Collection Bin.
2. Remove the Dirt Filter by pulling straight up
and off Filtered Air Inlet. (See Figure 4.)
Rinse under running water to clean.
IMPORTANT!
Dry thoroughly before use.
3. Slide the Dirt Filter over the Filtered Air Inlet
and re-attach.
IMPORTANT!
NEVER OPERATE THE
SWEEPEZE™ WITHOUT THE DIRT FILTER
PROPERLY IN PLACE.
4
Cleaning the Micro Exhaust Filter
Micro
Exhaust
Filter Holder
Figure 5
1. The Micro Exhaust Filter Holder slides up and out
of its housing on the side of the unit.
2. Gently pull the Filter out of the Filter Holder.
(See Figure 5.)
3. Tap Filter gently against trash container to free
and eliminate excess dirt and debris.
4. To clean the Filter, wash in mild soap and water;
rinse and dry thoroughly before using the unit.
Cleaning The Collection Bin
The Collection Bin should be washed
periodically.
1. Wash the Bin in warm water using a
mild soap. Avoid harsh or abrasive
cleaners or sponges. Rinse thoroughly.
TO AVOID DAMAGE, DO NOT PLACE
COLLECTION BIN IN THE DISHWASHER.
2. Let it air dry. Make sure the Collection
Bin is completely dry before putting it
back into the SweepEZE™.
3. Insert the assembled Collection Bin
following the instructions outlined
in the USER MAINTENANCE
INSTRUCTIONS on page 4.
IMPORTANT NOTES
Other than cleaning the Dirt Filter and
replacing the Micro Exhaust Filter Holder,
as described in this Owner’s Manual, this
Automatic Vacuuming Dust Bin is not user
serviceable. There are no user serviceable
parts inside the unit. Servicing by our
Authorized Service Center is required to
avoid damage to internal components.
Storage
Figure 6
5. If a new Filter is needed, replace with standard
HEPA HF4 filter cartridges, or cut a 3-inch by 4inch section of any micro filter to fit. Make sure
that it fits snugly in the Filter Holder.
6. Slide the Holder back into the unit with the Filter
facing outwards.
IMPORTANT!
NEVER OPERATE THE SWEEPEZE™
WITHOUT THE MICRO EXHAUST FILTER AND FILTER
HOLDER PROPERLY IN PLACE.
5
WST1800 Automatic Vacuuming Dust Bin
Unplug unit and clean Collection Bin and
all Filters before storing.
Store SweepEZE™ in its box in a clean,
dry place.
Never store SweepEZE™ while it is still
plugged in. Never wrap cord tightly around
the appliance, use the Cord Storage area
on the back of the SweepEZE™ unit.
Do not put any stress on the cord where it
enters the unit, as it could cause the cord
to wear and break.
TROUBLE SHOOTING
PROBLEM
POSSIBLE CAUSE
POSSIBLE SOLUTION
SweepEZE™
won’t run
1. Not firmly plugged in
2. Unit is in OFF position
3. Collection Bin Lid is not
on Collection Bin
4. No voltage in wall plug
5. Blown house fuse or
tripped circuit breaker
1. Plug in firmly
2. Turn Control Dial to MAN or AUTO position
3. Re-attach Collection Bin Lid to
top of Collection Bin
4. Check house fuse or circuit breaker
5. Replace house fuse or
reset circuit breaker
SweepEZE
does not
pick up debris
1. Dirt Inlet is blocked
2. Container is full
3. Debris may be too
large for inlet
1. Turn Control Dial to OFF position
2. Clean path of Dirt Inlet
3a. Empty Collection Bin
3b. Clear large debris
Eye-VAC™ Sensors
do not activate
1. Unit is not in AUTO Mode
1. Turn Control Dial to AUTO
Suction is not strong
1. Filters may be dirty
1a. Turn Control Dial to the OFF position
1b. Check Dirt Filter and Micro Exhaust
Filters to ensure they are clean
Clean or replace if necessary
Status Indicator
Light blinking
1. Eye-Vac™ Sensors have
been shut off for
30 seconds which
caused power to the
motor to be shut off
1a. Turn Control Dial to the OFF position
1b. Check inlet opening and remove debris
1c. Remove and empty Collection Bin
1d. Clean Sensors
1e. Turn Control Dial to the AUTO position
Debris at inlet before
unit is powered on
1. Turn Control Dial to the MANUAL position
2. Activate unit manually
.
WESTINGHOUSE SweepEZE™
AUTOMATIC VACUUMING DUST BIN
ACCESSORY / PARTS LIST
Replacement parts are available, and may be purchased through our Consumer Service Department
by calling 1-800-616-8689, Monday through Friday, 9am - 5pm Central Time, You can pay for
these parts by using either Visa, Mastercard, Discover, or American Express. Please be ready to
give the part number(s) when you call. Or log into our website to order at: www.eSalton.com
PART #
DESCRIPTION
PART #
DESCRIPTION
40226
40227
Micro Exhaust Filter
Collection Bin Lid
40228
40229
40251
Dirt Filter
Collection Bin
MicroFibre Towels, pack of 3
(not included w/unit)
6
LIMITED ONE-YEAR WARRANTY
Warranty Coverage: This product is warranted to be free from defects in materials or workmanship
for a period of one (1) year from the original purchase date. This product warranty is extended only to
the original consumer purchaser of the product and is not transferable. For a period of one (1) year
from the date of original purchase of the product, our Repair Center will,
at its option, either (1) repair the product or (2) replace the product with a reconditioned comparable
model. These remedies are the purchaser's exclusive remedies under this warranty.
Warranty Service: To obtain warranty service, you must call our warranty service number at
1-800-233-9054 for return instructions on how to deliver the product, in either the original packaging
or packaging affording an equal degree of protection to the Repair Center specified below. You must
enclose a copy of your sales receipt or other proof of purchase to demonstrate eligibility for warranty
coverage.
To return the appliance, ship to:
To contact us, please write to, call, or email:
ATTN: Repair Center
708 South Missouri Street
Macon, MO 63552 USA
Consumer Relations Department
PO Box 7366
Columbia MO 65205-7366 USA
1-800-233-9054
E-mail:consumer_relations@toastmaster.com
What Is Not Covered: This warranty does not cover damage resulting from misuse, accident,
commercial use, improper service or any other damage caused by anything other than defects in
material or workmanship during ordinary consumer use. This warranty is invalid if the serial number
has been altered or removed from the product. This warranty is valid only in the
United States and Canada.
LIMITATION ON DAMAGES: THERE SHALL BE NO LIABILITY FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY OR
CONDITION ON THIS PRODUCT.
DURATION OF IMPLIED WARRANTIES: EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE
LAW, ALL IMPLIED WARRANTIES AND CONDITIONS, INCLUDING, WITHOUT LIMITATION, IMPLIED
WARRANTIES AND CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE OR USE ON THIS PRODUCT ARE LIMITED IN DURATION TO THE DURATION OF THIS
WARRANTY.
Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or
allow limitations on how long an implied warranty lasts, so the above limitations or exclusions may
not apply to you. This warranty gives you specific legal rights and you may have other rights under
the laws of your jurisdiction.
For more information on our products, visit our website:
www.maxim-toastmaster.com.
WESTINGHOUSE, and “You Can Be Sure...If It's Westinghouse” are trademarks
of WESTINGHOUSE ELECTRIC CORPORATION and used under license by Salton, Inc.
SweepEZE™ is a trademark of Salton, Inc.
For more information on Salton products: visit our website: www.eSalton.com
©2005 Salton, Inc. All rights reserved.
Made in China
P/N 61533 Rev. 1
3/05
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising