Whirlpool Conservator CEDC392JQ0 User's Manual

Whirlpool Conservator CEDC392JQ0 User's Manual
120-VOLT COMPACT
ELECTRIC DRYER
Use & Care Guide
For questions about features, operation/performance,
parts, accessories or service call: 1-800-253-1301
or visit our website at
www.crosley.com
Table of Contents.......................................................2
8521904
TABLE OF CONTENTS
DRYER SAFETY .................................................................. 3
PARTS AND FEATURES .................................................... 4
INSTALLATION INSTRUCTIONS....................................... 5
Tools and Parts ................................................................. 5
Location Requirements .................................................... 5
Electrical Requirements .................................................... 7
Venting Requirements....................................................... 7
Determine Vent Length ..................................................... 8
Begin Installation............................................................... 8
Install Vent System............................................................ 9
Connect Vent .................................................................... 9
Complete Installation ...................................................... 10
DRYER USE....................................................................... 10
Starting Your Dryer ......................................................... 10
Stopping and Restarting ................................................. 11
Loading Clothes .............................................................. 11
Drying, Cycle, and Temperature Tips ............................. 11
CYCLE DESCRIPTIONS ................................................... 12
Permanent Press Cycle .................................................. 12
Timed Dry Cycle.............................................................. 12
Air Cycle .......................................................................... 12
End of Cycle Signal......................................................... 12
DRYER CARE .................................................................... 13
Cleaning the Lint Screen................................................. 13
Cleaning the Dryer Interior .............................................. 13
Removing Accumulated Lint from
Inside the Dryer Cabinet ................................................. 13
TROUBLESHOOTING....................................................... 14
ASSISTANCE OR SERVICE ............................................. 15
WARRANTY....................................................................... 16
2
DRYER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or
“WARNING.” These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic
precautions, including the following:
■
■
■
■
■
■
■
■
Read all instructions before using the dryer.
Do not place items exposed to cooking oils in
your dryer. Items contaminated with cooking oils
may contribute to a chemical reaction that could
cause a load to catch fire.
Do not dry articles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry-cleaning solvents, other flammable,
or explosive substances as they give off vapors
that could ignite or explode.
Do not allow children to play on or in the dryer.
Close supervision of children is necessary when
the dryer is used near children.
Before the dryer is removed from service or discarded, remove the door to the drying compartment.
Do not reach into the dryer if the drum is moving.
Do not install or store the dryer where it will be
exposed to the weather.
Do not tamper with controls.
■
■
■
■
■
■
■
Do not repair or replace any part of the dryer or
attempt any servicing unless specifically recommended in this Use and Care Guide or in published
user-repair instructions that you understand and have
the skills to carry out.
Do not use fabric softeners or products to eliminate
static unless recommended by the manufacturer of
the fabric softener or product.
Do not use heat to dry articles containing foam rubber
or similarly textured rubber-like materials.
Clean lint screen before or after each load.
Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint,
dust, and dirt.
The interior of the dryer and exhaust vent should be
cleaned periodically by qualified service personnel.
See Installation Instructions for grounding requirements.
SAVE THESE INSTRUCTIONS
3
PARTS AND FEATURES
1
4
2
5
3
1.
2.
3.
4.
5.
Control panel
Model and serial number label
Dryer drum
Lint screen
Moisture sensor
Control Panel
4
Location Requirements
INSTALLATION
INSTRUCTIONS
Tools and Parts
Tools needed
Check that you have everything necessary for correct installation.
Proper installation is your responsibility.
■
flat bladed screwdriver
■
safety glasses (optional)
■
level
■
duct tape
■
adjustable wrench
■
■
gloves (optional)
caulking gun and
compound (for installing
new exhaust vent)
■
tin snips (new vent
installations)
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Place dryer at least 18 inches (46 cm) above the
floor for a garage installation.
Failure to do so can result in death, explosion,
or fire.
1. Remove the tape that holds the drum to the cabinet. Move
the drum by hand in a counter-clockwise direction to make
certain all tape has been removed.
2. Wipe the interior of the drum thoroughly with a damp cloth
before using the dryer.
Check location where dryer will be installed. Proper installation is
your responsibility.
Parts supplied
■
Remove parts package from the dryer drum. Check that all parts
listed were included.
■ 1 - cycle control (timer) knob
A location that allows for proper exhaust installation. See
“Venting Requirements.”
■
A grounded electrical supply is required. See “Electrical
Requirements.”
■
4-inch metal exhaust vent is required. See “Venting
Requirements.”
■
A sturdy floor to support the total dryer weight of 110 lb
(50 kg).
■
Location must be large enough to fully open dryer door.
■
A level floor with a maximum slope of 1 in. (2.5 cm) under
entire dryer. Clothes may not tumble properly and automatic
sensor cycles may not operate correctly if dryer is not level.
■
1 - Push to Start button
■
4 - casters
■
2 - cord brackets
■
2 - screws
Parts needed
Check local codes, check existing electrical supply and venting,
and see “Venting Requirements” and “Electrical Requirements”
before purchasing parts.
You will need
Do not operate your dryer at temperatures below 45ºF (7ºC). At
lower temperatures, the dryer might not shut off at the end of an
automatic cycle. Drying times can be extended. Do not store
your dryer in a location with year round temperatures below
45ºF (7ºC).
Install the dryer where it is protected from water and/or weather.
Check code requirements. Some codes limit, or do not permit,
installation of the dryer in garages, closets, mobile homes, or
sleeping quarters. Contact your local building inspector.
WARNING: To reduce the risk of fire, this appliance MUST
BE EXHAUSTED OUTDOORS.
5
Recommended/Minimum Clearances
Most installations require a minimum 5 in. (12.7 cm) clearance
behind the dryer for the exhaust vent with elbows. See “Venting
Requirements.”
NOTE: Observe all governing codes and ordinances.
■
Additional spacing should be considered for ease of
installation and servicing.
■
Additional clearances might be required for wall, door, and
floor moldings.
■
Additional spacing of 1 in. (2.5 cm) on all sides of the dryer is
recommended to reduce noise transfer.
■
For closet installation with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
■
Companion appliance spacing should also be considered.
20 3 4"
(52.7 cm)
31"†
NOTE: No fuel-burning appliances may be installed in the same
closet as a dryer.
(78.7 cm)
Mobile Home-Additional Location Requirements
23 7 8"
(60.6 cm)
†Height with casters is 32½” (82.6 cm).
Recessed Area and Closet Installation
Your dryer needs a certain amount of space around it for proper
ventilation and for easier installation and servicing. The following
minimum installation spacings are required when the unit is to be
operated with, or without, the Stack Stand Kit. To purchase a
Stack Stand Kit, see “Assistance or Service.”
Minimum installation spacing
1. Side
2. Front
3. Closet door
4. Front—stack stand
5. Side—stack stand
* Additional space may be needed for exhaust elbow
** Opening is minimum for closet door. Louvered
door with air opening is acceptable.
*** May be 0” (0 cm) clearance
6
This dryer is suitable for mobile home installations. Follow the
information in “Location Requirements.”
The installation must conform to the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 245, HUD Part 280).
Electrical Requirements
Venting Requirements
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Fire Hazard
Use a heavy metal vent.
Do not remove ground prong.
Do not use an adapter.
Do not use a plastic vent.
Do not use a metal foil vent.
Do not use an extension cord.
Failure to follow these instructions can result in
death or fire.
Failure to follow these instructions can result in
death, fire, or electrical shock.
■
A 120-volt, 60-Hz., AC-only, 15- or 20- ampere fused
electrical supply is required.
■
A time-delay fuse or circuit breaker is recommended. Be sure
fuse or circuit breaker matches the rating of your line.
■
Use a separate circuit serving only your dryer.
■
Do not use an extension cord
n For a grounded, cord-connected dryer:
This dryer must be grounded. In the event of malfunction
or breakdown, grounding will reduce the risk of electric shock
by providing a path of least resistance for electric current. This
dryer is equipped with a cord having an equipment-grounding
conductor and a grounding plug. The plug must be plugged
into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
WARNING: Improper connection of the equipmentgrounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service representative or
personnel if you are in doubt as to whether the dryer is properly grounded. Do not modify the plug provided with the dryer: if
it will not fit the outlet, have a proper outlet installed by a
qualified electrician.
WARNING: To reduce the risk of fire, this dryer MUST BE
EXHAUSTED OUTDOORS.
■ Do not exhaust the dryer into any gas vent, chimney, wall,
ceiling, or a concealed space of a building.
■
The diameter of the heavy metal exhaust vent must be 4 in.
(10.2 cm).
■
Do not use an exhaust hood with a magnetic latch.
■
Do not install flexible metal vent in enclosed walls, ceilings or
floors.
■
Do not use screws or other fastening devices that extend into
the interior of the vent to secure vent.
IMPORTANT: Observe all governing codes and ordinances.
Improper venting can cause moisture and lint to collect
indoors, which may result in:
Moisture damage to woodwork, furniture, paint, wallpaper, carpets, etc.
Housecleaning problems and health problems.
Use a heavy metal vent. Do not use plastic or metal foil vent.
Rigid metal vent is recommended to prevent crushing and
kinking.
Flexible metal vent must be fully extended and supported when
the dryer is in its final position. Remove excess flexible metal vent
to avoid sagging and kinking that may result in reduced air flow.
An exhaust hood should cap the vent to prevent rodents and
insects from entering the home.
Exhaust hood must be at least 12 in. (30.5 cm) from the ground or
any object that may be in the path of the exhaust (such as
flowers, rocks or bushes, etc.).
If using an existing vent system, clean lint from the entire length
of the system and make sure exhaust hood is not plugged with
lint. Lint should be removed again every 2 years, or more often,
depending on dryer usage. Replace any plastic or metal foil vent
with rigid metal or flexible metal vent.
Use duct tape to seal all joints.
7
Vent Length Chart
Determine Vent Length
NOTE: Check periodically to ensure that the outside exhaust
hood is not blocked.
The maximum length of the exhaust system depends upon:
■ The type of vent (rigid metal or flexible metal).
■
Number of
90º turns
or elbows
Type of
vent
Box or
louvered
hoods
Angled
hoods
0
Rigid metal
Flexible metal
36 ft (11 m)
28 ft (8.5 m)
26 ft (7.9 m)
22 ft (6.7 m)
1
Rigid metal
Flexible metal
26 ft (7.9 m)
18 ft (5.5 m)
16 ft (4.9 m)
12 ft (3.7 m)
2
Rigid metal
Flexible metal
16 ft (4.9 m)
8 ft (2.8 m)
6 ft (1.8 m)
2 ft (.6 m)
The number of elbows (90° turns) used.
Recommended hood styles are shown here.
Special Venting Information for Mobile Homes
4"
(10.2 cm)
The exhaust vent must be securely fastened to a noncombustible
portion of the mobile home structure.
4"
(10.2 cm)
1. Box hood style
2. Louvered hood style
The angled hood style (shown following) is acceptable.
2
4"
10.2 cm
2.5"
6.4 cm
1
See the exhaust vent length chart that matches your hood type
for the maximum vent lengths you can use.
Do not use vent runs longer than specified in exhaust vent
length charts.
Exhaust systems longer than specified will:
■ Shorten the life of the dryer.
■
Reduce performance, resulting in longer drying times and
increased energy usage.
Determine the number of elbows you will need. In the column
listing the type of metal vent you are using (rigid metal or flexible
metal); find the maximum length of metal vent on the same line as
the number of elbows
3
1. Floor
2. Outside wall
3. Enclosure
Terminate the exhaust vent outside. The exhaust vent must not
terminate beneath the mobile home and must not be connected
to any other duct, vent, or chimney.
Begin Installation
Do not move dryer into its final position until the following steps
have been performed.
1
WARNING
2
Excessive Weight Hazard
Use two or more people to move and install
dryer.
Failure to do so can result in back or other injury.
3
Install cord bracket
3. Remove tape from the power cord and the rear panel.
1. Exhaust hood
2. Flexible metal vent or rigid metal vent
3. Elbow
8
4. Insert cord brackets into slotted holes in rear panel and
secure with screws provided.
Install Vent System
1. (Optional) Put on safety glasses and gloves.
2. Before installing the vent system, be sure to remove the wire
exhaust guard that is located at the exhaust outlet.
NOTE: Power supply cord may be wrapped around the brackets
for storage convenience when dryer is not in use.
Install casters
1. Lay the dryer on its side.
2. Use the carton to prevent damage to the dryer.
3. Install exhaust hood. Use caulking compound to seal exterior
wall opening around exhaust hood.
4. Connect vent to exhaust hood. Vent must fit inside exhaust
hood. Secure vent to exhaust hood with 4 in. (10.2 cm)
clamp.
5. Run vent to dryer location. Use the straightest path possible.
See “Determine Vent Length”. Avoid 90º turns. Use duct tape
to seal all joints.
Connect Vent
1. Using a 4 in. (10.2 cm) clamp, connect vent to exhaust outlet
in dryer. If connecting to existing vent, make sure the vent is
clean. The dryer vent must fit over the dryer exhaust outlet
and inside the exhaust hood. Make sure the vent is secured
to exhaust hood with a 4 in. (10.2 cm) clamp.
2. Move dryer into final position. Do not crush or kink vent.
Make sure dryer is level.
3. Screw casters into dryer base at four corners and tighten
securely.
4. Set the dryer upright. In doing so, be careful that the dryer
does not roll away from you.
■ As stated in “Location Requirements”, it is important that the
dryer be located on a level surface.
■
Leveling feet (Part No. 51594200) for use in permanent
installations may be purchased. See “Assistance or Service.”
9
Complete Installation
1. Check to be sure all parts are now installed. If there is an
extra part, go back through the steps to see which step was
skipped.
2. Check to be sure you have all of your tools.
3. Dispose of all packaging materials.
4. Check the dryer’s final location. Be sure the vent is not
crushed or kinked.
5. Check to be sure the dryer is level.
6. Plug into a grounded 3 prong outlet.
7. Remove the blue protective film on the console and any tape
remaining on the dryer.
8. Read “Dryer Use.”
9. Wipe the dryer drum interior thoroughly with a damp cloth to
remove any dust.
10. Set the dryer on a full heat cycle (not the Air cycle) for 20
minutes. Open the dryer door after five minutes and feel for
heat. If you do not feel heat, turn the dryer off and wait five
minutes.
Then check the following:
■
Controls are set in a running or “On” position.
■
Start button has been pushed firmly.
DRYER USE
Starting Your Dryer
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Do not dry anything that has ever had anything
flammable on it (even after washing).
Failure to follow these instructions can result in
death, explosion, or fire.
Repeat 5-minute test as outlined above. If dryer still does not
operate properly, check the following:
■ Dryer is plugged into a grounded outlet.
■
Electrical supply is connected.
■
House fuse is intact and tight; or circuit breaker has not
tripped.
■
Dryer door is closed.
■
If dryer makes an unusual noise, check that dryer is level.
NOTE: You may notice a burning odor. This odor is common
when the heating element is first used. The odor will go away.
Fire Hazard
No washer can completely remove oil.
Do not dry anything that has ever had any type of
oil on it (including cooking oils).
Items containing foam, rubber, or plastic must be
dried on a clothesline or by using an Air Cycle.
Failure to follow these instructions can result in
death or fire.
10
Before using your dryer, wipe the dryer drum with a damp cloth to
remove dust from storing and shipping.
1. Load clothes loosely into the dryer and close the door. Do not
pack the dryer. Allow space for clothes to tumble freely.
Loading Clothes
Load clothes loosely into the dryer. Do not pack the dryer. Allow
space for clothes to tumble freely. The following chart shows the
maximum load you can place in your compact dryer. Expect
longer drying times.
2. Turn the Cycle Control knob to the recommended cycle for
the type of load being dried. Use the Energy Preferred
Automatic Setting (*) to dry most heavyweight and medium
weight loads. See “Drying, Cycle, and Temperature Tips.”
Heavy work
clothes
2 pair of pants, 3 work shirts
Delicates
1 camisole, 2 slips, 4 undergarments,
1 set of sleepwear, 1 half slip
Towels
9 bath towels; or 6 bath towels, 3 hand
towels, 6 wash cloths
Mixed Load
2 pillowcases, 1 T-shirt, 2 shirts, 1 pair
slacks
Knits
2 slacks, 2 shirts; or 3 dresses
Perm. Press
6 shirts; or 2 double sheets & 2 pillowcases;
or 2 singles sheets & 2 pillowcases
Drying, Cycle, and Temperature Tips
3. Push the START button.
Stopping and Restarting
You can stop your dryer any time during a cycle.
To stop your dryer
Open the dryer door or turn the Cycle Control knob to OFF.
NOTE: The Cycle Control knob should point to an Off area when
the dryer is not in use.
Select the correct cycle and temperature for your load.
Your dryer tumbles the load without heat during the last few
minutes of all cycles to make the load easier to handle.
Drying tips
■
Follow care label directions when they are available.
■
If you use fabric softener sheets, use only those labeled
“dryer safe.” Follow package instructions.
■
Remove the load from the dryer as soon as tumbling stops to
reduce wrinkling. This is especially important for permanent
press, knits, and synthetic fabrics.
To restart your dryer
1. Close the door.
2. Select a new cycle (if desired).
3. Push START.
Cycle and temperature tips
■
Dry most loads using the Energy Preferred Automatic
Setting (*).
■
Use a no heat (air) setting for rubber, plastic, or heat sensitive
fabrics.
■
Line dry bonded or laminated fabrics.
NOTE: If you have questions about drying temperatures for
various loads, refer to the care label directions.
11
CYCLE DESCRIPTIONS
Air Cycle
Use this cycle for items that require drying without heat, such as
rubber, plastic, and heat-sensitive fabrics. See the chart for
examples of items that can be dried using an air cycle.
Type of Load
Time*
Foam rubber—pillows, padded bras,
stuffed toys
Plastic—shower curtains, tablecloths
Rubber-backed rugs
Olefin, polypropylene, sheer nylon
20 - 30
20 - 30
40 - 50
10 - 20
*(Minutes). Reset cycle to complete drying, if needed.
When using an air cycle
■ Check to see that coverings are securely stitched.
Cycle Control knob
Permanent Press Cycle
This automatic cycle shuts off the dryer when the selected
dryness is reached. The Cycle Control knob does not move
until the load is almost dry. After the cool down, the knob
automatically turns to an Off area and tumbling stops.
Dry most loads using the Energy Preferred Automatic Setting (*).
■ If the load is drier than you like, select a setting closer to
Less Dry the next time you dry a similar load.
■
If the load is not as dry as you like, complete drying using the
Timed Dry cycle. The next time you dry a similar load, select a
setting closer to More Dry.
NOTE: Drying time with an automatic cycle varies according to
the type of fabric, size of load, and temperature setting.
Timed Dry Cycle
Use this cycle to complete drying if items are still damp after the
automatic cycle.
Timed Drying is also useful for:
■ Heavyweight items and work clothes that require a long
drying time.
■
Lightweight items, such as lingerie, blouses, and knits that
require a short drying time.
For damp dry, turn the Cycle Control knob to 30 minutes or less.
12
■
Shake and fluff pillows by hand periodically during cycle.
■
Dry item completely. Foam rubber pillows are slow to dry.
End of Cycle Signal
The dryer sounds a signal to let you know when the cycle is
finished. The signal is not adjustable and cannot be turned off.
The signal is helpful when you are drying permanent press,
synthetics, and other items that should be taken out as soon as
the dryer stops.
DRYER CARE
Cleaning the Dryer Interior
Cleaning the Lint Screen
Every load cleaning
The lint screen is located inside the dryer drum, on the back wall.
Clean it before each load. A screen blocked by lint can increase
drying time.
To clean
1. Open the door and pull the lint screen straight out.
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion,
or fire.
To clean dryer drum
2. Squeeze body of lint screen lightly while pulling off the cover.
3. Roll lint off the screen with your fingers. Do not rinse or wash
screen to remove lint. Wet lint is hard to remove.
4. Replace cover on lint screen body. Push the lint screen firmly
back into place and close the door.
IMPORTANT:
■ Do not run the dryer with the lint screen loose, damaged,
blocked, or missing. Doing so can cause overheating and
damage to both the dryer and fabrics.
■
Some towels made of synthetic fibers and natural fibers
(polyester and cotton blends) may shed more lint than other
towels, causing your dryer’s lint screen to fill up faster. Be
sure to remove lint from the lint screen before and after drying
new towels.
As needed cleaning
Laundry detergent and fabric softener residue can build up on the
lint screen. This buildup can cause longer drying times for your
clothes, or cause the dryer to stop before your load is completely
dry. The screen is probably clogged if lint falls off the screen.
Clean the lint screen with a nylon brush every six months, or
more frequently if it becomes clogged due to a residue buildup.
To wash
1. Wet both the lint screen cover and body with hot water.
2. Wet a nylon brush with hot water and liquid detergent. Scrub
lint screen cover and body with the brush to remove residue
buildup.
1. Make a paste with powdered laundry detergent and very
warm water.
2. Apply paste to a soft cloth.
OR
Apply a liquid, non-flammable household cleaner to the
stained area and rub with a soft cloth until all excess dye is
removed.
3. Wipe drum thoroughly with a damp cloth.
4. Tumble a load of clean cloths or towels to dry drum.
NOTE: Garments which contain unstable dyes, such as denim
blue jeans or brightly colored cotton items, may discolor the
dryer interior. These stains are not harmful to your dryer and will
not stain future loads of clothes. Dry unstable dye items insideout to prevent dye transfer.
Removing Accumulated Lint from
Inside the Dryer Cabinet
Lint should be removed every two years, or more often,
depending on dryer usage. Cleaning should be done by a
qualified person.
3. Rinse with hot water.
4. Thoroughly dry lint screen body and cover with a clean towel.
Replace in dryer.
13
TROUBLESHOOTING
First try the solutions suggested here and possibly avoid
the cost of a service call...
Lint on load
■
Is the lint screen clogged?
Clean lint screen. Check for air movement.
■
Is the load properly sorted?
Sort lint givers (towels, chenille) from lint takers (corduroy,
synthetics). Also sort by color.
■
Is the load too big or too heavy?
Dry smaller loads so lint can be carried to the lint screen.
■
Was the load overdried?
Use correct dryer settings for load type. Overdrying can
cause lint-attracting static electricity. See “Drying, Cycle, and
Temperature Tips.”
■
Was paper or tissue left in pockets?
■
Is pilling being mistaken for lint?
Pilling (surface fuzz) is caused by normal wear and
laundering.
Clothes are not drying satisfactorily
■
The compact dryer operates at a lower wattage. Expect
longer drying times.
■
Check the following:
Is the wire exhaust guard removed from the back of the
dryer?
Is the lint screen clogged with lint?
Is the exhaust vent or outside exhaust hood clogged with lint,
restricting air movement? Run the dryer for 5-10 minutes.
Hold your hand under the outside exhaust hood to check air
movement. If you do not feel air movement, clean exhaust
system of lint or replace exhaust vent with heavy metal or
flexible metal vent. See “Installation Instructions.”
Stains on load or color change
■
Was dryer fabric softener properly used?
Add dryer fabric softener sheets at the beginning of the cycle.
Fabric softener sheets added to a partially-dried load can
stain your garments.
■
Were items soiled when placed in the dryer?
Items should be clean before being dried.
■
Were items properly sorted?
Sort light colors from dark colors. Sort colorfast items from
noncolorfast items.
Is the exhaust vent crushed or kinked? Replace with heavy
metal or flexible metal vent. See “Installation Instructions.”
Has an air dry cycle been selected? Select the right cycle for
the types of garments being dried. See “Drying, Cycle, and
Temperature Tips.”
Are fabric softener sheets blocking the grill? Use only one
fabric softener sheet and only use it once.
Is the automatic cycle ending early? This cycle will end early
if dryer load is not contacting the sensor strips. Level the
dryer. See “Installation Instructions.”
Is the dryer located in a room with temperature below
45ºF (7ºC)?
Proper operation of dryer cycles requires temperatures above
45ºF (7ºC).
■
Items shrinking
■
Was the dryer overloaded?
Dry smaller loads that can tumble freely.
■
Did the load overdry?
Check the manufacturer’s care label. Match dryer setting to
load type. See “Drying, Cycle, and Temperature Tips.”
Was a cold rinse water used? Was the load very wet?
Expect longer drying times with items rinsed in cold water
and with items that hold moisture (cottons).
■
Is the load too large and heavy to dry quickly?
Separate the load to tumble freely.
■
Loads are wrinkled
■
Was the load removed from dryer at the end of the cycle?
■
Was the dryer overloaded?
Dry smaller loads that can tumble freely.
■
Did the load overdry?
Check the manufacturer’s care label. Match dryer setting to
load type. See “Drying, Cycle, and Temperature Tips.”
Dryer will not run
Check the following:
Is the power cord plugged into a grounded 3 prong outlet?
■
Has a fuse blown, or has a circuit breaker tripped?
Odors
Was a regular fuse used? Use a time-delay fuse.
Is the dryer door firmly closed?
■
Have you recently been painting, staining, or varnishing in
the area where your dryer is located?
If so, ventilate the area. When the odors or fumes are gone
from the area, re-wash and dry the clothing.
■
Is the dryer being used for the first time?
The new electric heating element may have an odor. The odor
will be gone after the first cycle.
Was the START button firmly pressed?
Is a cycle selected?
Unusual sounds
■
Has the dryer had a period of non-use?
If the dryer hasn’t been used for a while, there may be a
thumping sound during the first few minutes of operation.
Garment damage
■
Check the following:
Were zippers, snaps, and hooks left open?
Were strings and sashes tied to prevent tangling?
Were care label instructions followed?
Were items damaged before drying?
14
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check
“Troubleshooting.” It may save you the cost of a service call. If
you still need help, follow the instructions below.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
If you need replacement parts
If you need to order replacement parts, we recommend that you
only use Factory Specified Parts. These parts will fit right and
work right because they are made with the same precision used
to build every new CROSLEY® appliance. To locate replacement
parts in your area, call our Customer Interaction Center or your
nearest designated service center.
For assistance or service
Call the Customer Interaction Center at 1-800-253-1301.
Our consultants provide assistance with:
■ Features and specifications on our full line of appliances
■
Installation information
■
Use and maintenance procedures
■
Accessory and repair parts sales
■
Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.)
■
Referrals to local dealers, repair parts distributors, and
service companies
Whirlpool designated service technicians are trained to fulfill the
product warranty and provide after-warranty service, anywhere in
the United States.
To locate the Whirlpool designated service company in your area,
you can also look in your telephone directory Yellow Pages.
For further assistance
If you need further assistance, you can write to us with any
questions or concerns at:
Crosley Distribution Center
c/o Correspondence Dept.
675 North Main Street
Winston-Salem, NC 27102-2111
Please include a daytime phone number in your correspondence.
15
CROSLEY® DRYER WARRANTY
ONE-YEAR FULL WARRANTY
For one year from the date of purchase, when this dryer is operated and maintained according to instructions attached to or furnished
with the product, Whirlpool Corporation will pay for Factory Specified Parts and repair labor to correct defects in materials or
workmanship. Service must be provided by a Whirlpool designated service company.
Whirlpool Corporation will not pay for:
1. Service calls to correct the installation of your dryer, including venting. Heavy 4 in. (10.2 cm) metal exhaust vent must be used. Refer
to the venting section of this manual and your Installation Instructions.
2. Service calls to instruct you how to use your dryer, to replace house fuses or correct house wiring or reset circuit breakers, or to
replace owner accessible light bulbs.
3. Repairs when your dryer is used in other than normal, single-family household use.
4. Damage resulting from accident, alteration, misuse, abuse, fire, floods, acts of God, improper installation (including, but not limited
to, venting with plastic or flexible foil), installation not in accordance with local electrical and plumbing codes, or use of products not
approved by Whirlpool Corporation.
5. Replacement parts or repair labor costs for units operated outside the United States.
6. Pickup and delivery. This product is designed to be repaired in the home.
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
WHIRLPOOL CORPORATION SHALL NOT BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow the exclusion or limitation of incidental
or consequential damages, so this exclusion or limitation may not
apply to you. This warranty gives you specific legal rights, and
you may also have other rights which may vary from state to
state.
Outside the 50 United States, this warranty does not apply.
Contact your authorized Crosley dealer to determine if
another warranty applies.
If you need service, first see “Troubleshooting.” Additional help
can be found by checking “Assistance or Service,” or by calling
our Customer Interaction Center at 1-800-253-1301, from
anywhere in the U.S.A., or write: Crosley Distribution Center,
c/o Correspondence Dept., 675 N. Main St., Winston-Salem, NC
27102-2111.
5/00
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your dryer to better
help you obtain assistance or service if you ever need it. You will
need to know your complete model number and serial number.
You can find this information on the model and serial number
label/plate, located on your appliance as shown in “Parts and
Features.”
Dealer name ____________________________________________________
Address ________________________________________________________
Phone number __________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________
8521904
© 2000. All rights reserved.
® Registered Trademark of Crosley
9/00
Printed in U.S.A.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement