Whirlpool EDZOZK Use and care guide

Add to My manuals
26 Pages


Whirlpool EDZOZK Use and care guide | Manualzz



A Note To You 2



Before Using Your

Refrigerator 5


Caring For Your


] Food StorageGuide 22



If You Need tF%izi:



Warranty 28


Call us with questions or comments.




A Note To You

Thank you for buying a Whirlpool@ appliance.

You have purchased a quality, worMclass home appliance. Years of engineering experience went into its manufacturing. To ensure that you enjoy many years of trouble-free operation, we developed this Use and Care Guide. It is full of valuable information on how to operate and maintain your appliance properfy and safely. Please read it carefully. Also, please com- plete and mail the Ownership Registration Card provided with your appliance. This will help us notify you about any new information on your appliance.

Your safety is important to us.

This guide contains safety symbols and statements. Please pay special attention to these symbols and follow any instructions given. Here is a brief explanation of the use of each symbol.

Our Consumer Assistance is toll-free, 24 hours a day.

Center number, l-800-253-1301,

If you ever have a question concerning your appliance’s operation, or if you need service, first see “If You Need Assistance Or Service” on page 24. If you need further help, feel free to call our Consumer Assistance Center. When calling, you will need to know your appliance’s complete model number and serial number. You can find this information on the model and serial number label (see diagram on page 4). For your convenience, we have included a handy place below for you to record these numbers, the purchase date from the sales slip and your dealer’s name and telephone number. Keep this book and the sales slip together in a safe place for future reference.

Model Number

Serial Number

Purchase Date

Dealer Name

Dealer Phone

Important Safety Instructions


Read all instructions before using the refrigerator.

@Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still danger- ous . . . even if they will “just sit in the garage a few days.”

If you are getting rid of your old refrig- erator, do it safely. eNever allow children to operate, play with, or crawl inside the refrigerator. l

Never clean refrigerator parts with flammable fluicls. The fumes can create a fire hazard or explosion. l









Help us help you

l l l l l l l l l


Install and level the refrigerator on a floor that will hold the weight and in an area suitable for its size and use.

Do not install the refrigerator near an oven, radiator or other heat source.

Do not use the refrigerator in an area where the room temperature will fall below

55°F (13°C).

Keep the refrigerator out of the weather.

Connect the refrigerator only to the proper kind of outlet, with the correct electrical supply and grounding.

Do not load the refrigerator with food before it has time to get properly cold.

Use the refrigerator only for the uses described in this manual.

Properly maintain the refrigerator.

Be sure the refrigerator is not used by anyone unable to operate it properly.


Parts And Features

This section contains captioned illustrations. Use them to become familiar with where all parts and features are located and what they look like.

Control panel Llght

Automatic ke maker and ke

Door shelves

Base‘ grille

Model EDSOZK shown

Control panel


Freezer control


Refrigerator control

Before Using Your


In This Section

Page Page

Cleaning it . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installing It properly . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Plugging it In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Leveling it . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

It is important to prepare your refrigerator for use. This section tells you how to clean it, connect it to a power source, install it and level it.

Cleaning it

Removing packaging materials

Remove tape and any inside labels (except the model and serial number label) before using the refrigerator. l l

To remove any remaining glue:

Rub briskly with thumb to make a ball, then remove.


Soak area with liquid handdishwashing detergent before removing glue as described above. Do not use sharp instruments, rubbing alcohol, flammable fluids or abrasive cleaners. These can damage the material. See “Important

Safety Instructions” on page 3.

NOTE: Do not remove any permanent instruction labels inside your refrigerator. Do not remove the Tech Sheet fastened under the refrigerator at the front

Cleaning it before use

After removing all packaging materials, clean your refrigerator before using it, if necessary. See cleaning instructions on pages 19-20.

Plugging it in

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15 or 20 ampere fused and properly grounded electriil supply is required. ll is recommended that a separate circuit serving only this appliance be provided. Use a receptacle which cannot be turned off with a switch or pull chain. Do not use an extension cord.

See Electriil Requirements and Ground- ing Instructions Sheet in your Literature


&prong grounding type wall receptacle \

Refrigerator power cord

3-prong grounding



Installing it properly

1. Allow ‘$5 inch (1.25 cm) space on each side and at the top of the refrigerator for ease of installation.

2. If the refrigerator is to be against a wall, you might want to leave extra space on the hinge side closest to the wall so the door can be opened wider.

3. The refrigerator can be flush against the wall.

Leveling it

Your refrigerator has 2 front leveling screws-one on the right and one on the left.

To adjust one or both of these, follow the directions below.

1. Remove base grille. (See page 16.)

2. To raise front, turn screw clockwise.

3. To lower front, turn screw counterclock- wise.

4. Check with level.

5. Replace base grille. (See page 16.)

Right to raise; left to lower

Use 8 screw-


Using Your Refrigerator

In This Section


Setting the controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Changing the control settings . . . . . . . . . . . 8

Adjustlng the shelf glide . . . . . . . . . . . . . . . . . . . . 9

Adjusting the refrigerator shelves . . ..Q

Using the egg bin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Removing the crisper and crisper cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Removing the meat drawer and cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Removing the freezer shelves . . . . . . . . . 11

Removing the freezer bin . . . . . . . . . . . . . . . . . 11

Removing the freezer door shelves . ..ll


Using the ice cubs trays . . . . . . . . . . . . . . . . . . 12

Uslng the Ice dispenser (ED22ZR) ..12

Using the automatic ke maker . . . . . . . . 13

Removing the ice maker storage bin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Solving common Ice maker/ dispenser problems . . . . . . . . . . . . . . . . . . . . . . . . . 15

Removing the base grille . . . . . . . . . . . . . . . ..16

Changing the light bulbs . . . . . . . . . . . . . . . . . 16

Understanding the sounds you may hear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Saving energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

To obtain the best possible results from your refrigerator, it is important that you operate it properly. This section tells you how to set the controls, remove and adjust some of the fea- tures in your refrigerator, and how to save energy.

Setting the controls

Controls for the refrigerator and freezer are in the refrigerator. When you plug in the refrigerator for the first time:

1. Set the Refrigerator Control to 3.

Refrigerator Control adjustments range from

1 (warmest) to 5 (coldest).

2. Set the Freezer Control to B.

Freezer Control adjustments range from

A (warmest) to C (coldest).


3. Give the refrigerator time to cool down completely before adding food. This may take several hours.

The settings indicated above should be correct for normal, household refrigerator usage. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm. lf you need to adjust these settings, see “Changing the control settings” below.

NOTE: The Automatic Exterior Moisture control continuously guards against moisture build-up on the outside of your refrigerator cabinet. This control does not have to be set or adjusted.

Changing the control settings

If you need to adjust temperatures in refrigerator or freezer, use the settings listed in the chart below as a guide. If you have questions, call our Consumer Assistance

Center number. (See page 25.) l l l

Adjust the Refrigerator Control first.

Wait at least 24 hours between adjustments.

Then adjust the Freezer Control if needed.


Refrigerator section too warm

Freezer section too warm

Refrigerator section too cold

Ice not made fast enough

Both sections too warm

REASON: l l l

Door opened often

Large amount of food added

Room temperature too warm l l l

Door opened often

Large amount of food added

Very cokf room temperature

(can’t cycle often enough) l

Controls not set correctly for your conditions l l

Heavy ice usage

Very cold room temperature

(can’t cycle often enough) l

Door opened often l l

Large amount of food added

Very warm or very cold rcom temperatures























Adjusting the shelf glide

Use the shelf glide to secure odd-shaped items or to separate other items.

1. Grasp glide.

2. Slide glide along track.

NOTE: Shelf glide cannot be removed.

Adjusting the refrigerator shelves

Adjust shelves to match the way you use your refrigerator.

To remove the shelves:

1. Remove items from the shelf.

2. Tilt shelf up at front.

3. Lift shelf up at back.

4. Pull shelf straight out.

To replace the shelves:

1. Guide the rear shelf hooks into the slots in the shelf supports on the back liner wall.

2. Tilt front of shelf up until hooks drop into slots.

3. Lower front of shelf to a level position.

Using the egg bin

The egg bin has two pieces - the lid and the bin. Use the egg bin to hold one, two or three dozen eggs.

To hold one dozen eggs:

Place a dozen eggs (in or out of carton) in the bin and cover with the lid.

To hold two dozen eggs:

Place two dozen eggs loose in the bin and cover with the lid.

To hold three dozen eggs:

Place two dozen eggs loose in the bin.

Invert the lid and place it on the bin. Put a dozen eggs, in their carton, on top of the lid.




Removing the crisper and crisper cover

To remove the crisper:

1. Slide the crisper straight out to the stop.

2. Lii the front slightly.

3. Slide out the rest of the way.

4. Replace in reverse order.

Pull out to the stop, lift the front and pull again.

To remove the cover:

1. Hold cover firmly with both hands and lifl front of cover off supports.

2. Lift cover out by pulling up and out.

To replace the cover:

1. Fit back of cover into notch supports on walls of refrigerator.

2. Lower front into place.

Lift the cover front, then the back

Removing the meat drawer and cover

To remove the meat drawer:

1. Slide the meat drawer straight out to the stop.

Pull out to the stop, lift the front and pull again.

2. Lift the front slightly.

3. Slide out the rest of the way.

4. Replace in reverse order.

To remove the cover:

1. Remove the crisper, the crisper cover and the meat drawer.

2. Tilt front of cover up.

3. Lift cover at back and pull straight out.

4. Replace in reverse order.


Removing the freezer shelves

To remove the shelf:

1. Lii right side of shelf off supports.

2. Slide shetf out of shelf support holes.

3. Replace in reverse order.

Removing the freezer bin


To remove the bin:

1. Slide bin out to the stop.

2. Lii the front to clear the stop.

3. Slide bin out the rest of the way.

To replace the bin:

1. Place bin on the slides.

2. Make sure the wire stops clear the front of the slides.

3. Slide bin in all the way.

Pull out to the stop, lift the front and pull again.

Removing the freezer door shelves


Remove the freezer door shelves for easier cleaning.

To remove the door shelves:

1. Grasp shelf at both ends.

2. Lift shelf up and pull it out.

To replace the door shelves:

1. Insert door shelf hooks into guides on both edges of door liner.

2. Push shelf down to lock into place.


using the ice cube trays


If you don’t use the cubes, they may shrink.

The moving cold air starts a slow evapora- tion. The longer you store cubes, the smaller they get.

To remove ice:

1. Hold tray at both ends.

2. Twist slightly.

using the ice dispenser


Personal Injury Hazard

Tumbling ice and pressure can break a fragile glass. Use a sturdy glass when dispensing ice or water.

Failure to do so could result in personal injury or breakage.

Ice dispenses from the ice maker storage bin in the freezer. When you press the dispenser bar, a trapdoor opens in a chute between the dispenser and the ice bin. Ice moves from the bin and falls through the chute. When you release the dispenser bar, a buzzing sound may be heard for a few seconds as the trapdoor closes. The dis- penser system will not operate when the freezer door is open.

To dispense ice:

1. Press a sturdy glass against the ice dispenser bar. Hold glass close to dispenser opening so ice does not fall outside of glass.

2. Remove the glass to stop dispensing.

NOTE: The first few batches of ice may have an off-flavor from new plumbing and parts. Throw the ice away. Also, take large amounts of ice from the ice bin, not through the dispenser.


Using the automatic ice maker

(Factory-installed on EDZZZR, optional on EDZOZK)


Here are a few things you will want to know about your automatic ice maker:

The ON/OFF lever is a wire signal arm.

DOWN to make ice automatically.

UP to shut off the ice maker. l

NOTE: Do not turn ice maker on until il is conneded to the water supply. Instruc- tions for ice maker water supply hook up are attached to the back of the refrigerator cabinet.

For EDSOZK only: The dial or lever on the side of the ice maker changes the size of the cubes. l l l l

It is normal for ice crescents to be attached by a comer. They break apart easily.

The ice maker will not operate until the freezer is coM enough to make ice. This can take overnight.

If ice is not being made fast enough and more ice is needed, turn the Refrigerator

Control toward a higher number. Wait a day and, if necessary, turn the Freezer

Control toward C.

Good water quality is important for good ice quality. Try to avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt from a matfunctioning softener) can damage the ice maker mold and lead to poor ice quality. lf a softened water supply cannot be avoided, make sure the water softener is operating properly and well maintained.

4 upto maker. t DOWNto start ke maker.


Removing the ice maker storage bin


l l l

Remove, empty and clean the storage bin if: the ice dispenser has not, or will not, be used for a week or more. a power failure causes ice in the bin to melt and freeze together. the ice dispenser is not used regularly.

To remove ke bin:

1. Pull the covering panel out from the bottom and slide it to the rear.

2. Lift the signal arm so it clicks into the OFF

(up) position. Ice can still be dispensed, but no more can be made.

3. Lift the front of the storage bin and pull it


4. Empty the ice bin. Use hot or warm water to melt the ice if necessary. Never use anything sharp to break up ice in the bin. This can damage the bin and dis- penser mechanism.

5. Wash with mild detergent. Rinse well. Do not use harsh or abrasive cleaners or solvents.

6. When replacing the bin, make sure it is pushed in all the way. Then push the signal arm down to the ON position to restart ice production.


Solving common ice maker/dispenser problems


Ice dispenser won’t work

CAUSE l l l

Freezer door open

Ice bin not properly installed

Wrong ice in bin


Close the freezer door.

Make sure bin is pushed in all the way. l l

Use only crescents from ice maker.

Shake the bin occasionally to keep cubes separated and to increase storage room.

Dump oki ice and make a new supply. l

Dispenser not used for extended periods, causing ice cubes to melt together

Ice dispenser l

Ice dispenser bar held stops working in too long

Off-taste or odor in ice l l

Ice attracts airborne odors; old ice

Water quality l l l

Foods not properly wrapped

Ice bin and freezer may need cleaning

Plumbing to ice maker l

New ice maker l l

Wait about 3 minutes for the dispenser motor to reset.

Large amounts of ice shouti be taken from the bin, not through the dispenser. l l

Dump old ice and make a new supply.

Store excess ice in covered container.

Water containing minerals (such as sulfur) may require a filter to remove. l

Wrap properly. See pages 22 and 23. l l l

Clean freezer and ice bin. See cleaning chart on pages 19 and 20.

Follow Installation Instructions for proper ice maker water supply hook up. (See back of refrigerator cabinet.)

The first few loads of ice from a new ice maker may have an off-taste. Dump ice and make a new supply.



Removing the base grille

To remove the grille:

1. Open both doors.

2. Pull base grille forward to release the support tabs from the metal clips.

3. Do not remove Tech Sheet fastened behind the grille.

To replace the grille:

1. Line up grille support tabs with metal clips.

2. Push firmly to snap into place.

3. Close the doors.

See cleaning instructions for defrost pan and condenser coils on page 20.

Changing the light bulbs

Electrical Shock Hazard

Before removing a light bulb, either unplug the refrigerator or disconnect the electricity leading to it at the main sonal injury.

To change refrigerator light:

1. Disconnect refrigerator from power supply.

2. Reach behind the Control Console to remove bulb.

3. Replace bulb with a 40-watt appliance bulb.

4. Reconnect refrigerator to power supply.

/==+-=@ _T

Condenser coils



_--- grille IL Defrost pan

SUPpofl tabs



To change crisper light:

1. Disconnect refrigerator from power supply.

2. Pull top of light shield forward until it snaps free.

3. Lower light shield to clear bottom supports.

4. Pull light shield straight out to remove.

5. Replace bulb with bulb. a 40-watt appliance

6. Replace light shield in reverse order.

7. Reconnect refrigerator to power suppfy.

To change freezer light:

1. Disconnect refrigerator from power supply.

2. Push in sides of light shield until it snaps free.

3. Replace bulb with a 40-watt appliance bulb.

4. Replace light shield.

5. Reconnect refrigerator to power supply.

NOTE: Not all commercial appliance bulbs will fit your refrigerator. Be sure to replace a bulb with one of the same size and shape. risper light


Understanding the sounds you may hear

Your new refrigerator may make sounds that your old one didn’t. Because the sounds are new to you, you might be concerned about them. Don’t be. Most of the new sounds are normal. Hard surfaces like the floor, walls and cabinets can make the sounds seem louder.

The following describes the kinds of sounds that might be new to you, and what may be making them. l

Water sounds

Ice maker sounds

trickling water thud (clatter of ice)

Slight hum, soft hiss


When the refrigerator stops running, you may hear gurgling in the tubing for a few minutes after it stops. You may also hear defrost water running into the defrost water pan.

You may hear the refrigerator’s fan motor and moving air.

Clicking or snapping sounds

If your refrigerator has an automatic ice maker, you may hear buzzing (from the water valve), trickling water and the datter of ice dumped into the bin.

Running sounds

The thermostat makes a definite click when the refrigerator stops running. It also makes a sound when the refrigerator starts. The defrost timer will click when the defrost cycle starts.

Your refrigerator has a high-efficiency compressor and motor. It will run longer than older designs. It may even seem to run most of the time.

Saving energy

l l

You can help your refrigerator use less electricity.

Check door gaskets for a tight seal. Level the cabinet to be sure of a good seal.

Clean the condenser coils regularly. l

Open the door as few times as possible.

Think about what you need before you open the door. Get everything out at one time. Keep food organized so you won’t have to search for what you want. Close door as won as food is removed. l l l

Go ahead and fill up the refrigerator, but don’t overcrowd it so air movement is blocked.

It is a waste of electricity to set the refrig- erator and freezer to temperatures colder than they need to be. If ice cream is firm in the freezer and drinks are as cold as your family likes them, that’s cold enough.

Make sure your refrigerator is not next to a heat source such as a range, water heater, furnace, radiator or in direct sunlight.


Caring For Your Refrigerator

In This Section

Page Page

Cleaning your refrigerator . . . . . . . . . . . . . . . 19 Power interruptions . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Vacation and moving care . . . . . . . . . . . . . . . 20

Your refrigerator is built to give you many years of dependable service. However, there are a few things you can do to help extend its product life. This section tells you how to clean your refrigerator and what to do when going on vacation, moving or during a power outage.

Cleaning your refrigerator

Both the refrigerator and freezer sections defrost automatically. However, clean both about once a month to prevent odors from building up. wipe up spills right away.

To clean your refrigerator, turn the Refrig- erator Control to OFF, unplug it, take out all removable parts and clean the refrigerator according to the following directions.

Personal Injury Hazard

Refrigeration system tubes are located near the defrost pan and can become hot. Remove and install defrost pan carefully.

Failure to do so could result in personal injury.


Removable parts

(shelves, crisper, etc.)


Inside walls

(allow freezer to warm up so cloth won’t stick)


Sponge or cloth with mild detergent and warm water

Sponge, cloth or paper towel with mild detergent, warm water and an appliance wax (or good auto paste wax)

Sponge, soft cloth or paper towel with baking soda or mild detergent and warm water


Hand wash, rinse and dry thor- oughly. l l l

Wash outside of cabinet. Do not use abrasive or harsh cleaners.

Rinse and dry thoroughly.

Wax painted metal surfaces at least twice a year. Apply wax with a clean, soft cloth. Waxing painted metal surfaces provides rust protection. Do not wax plastic parts. l l

Wash with mixture of warm water and:

- mild detergent, or

- baking soda (2 tablespoons [26 g] to 1 quart [.95 L] of water).

Rinse and dry thoroughly. continued on next page



Door liners and gaskets

Plastic parts

(covers and paneW

Defrost pan

Condenser coils

Floor under refrigerator


Sponge, soft doth or paper towel with mild detergent and warm water

Soft, clean sponge or soft, clean cloth with mild detergent and warm water

Sponge or cloth with mild detergent and warm water

Vacuum cleaner with extended narrow attachment

Floor cleaners


Wash, rinse and dry thoroughly.

DO NOT USE cleaning waxes, concen- trated detergents, bleaches or cleaners containing petroleum on plastic parts. l

Wash, rinse and dry thoroughly.

DO NOT USE paper towels, window sprays, scouring cleansers or flam- mabk fluids. These can scratch or damage material. See “Important Safety

Instructions” on page 3. l l l l l l

Remove base grille. (See page 16.)

To remove defrost pan, lift pan over wire brace (remove tape; if any).

Wash, rinse and dry thoroughly.

Replace with notched comer to the rear.

Push it in all the way.

Make sure defrost pan drain tube is pointing into pan.

Replace base grille. l l l

Remove base grille.

Vacuum coils when dustyor dirty. Coils may need to be cleaned as often as every other month.

Replace base grille. l l l l

Roll refrigerator out only as far as the water supply line allows.

Clean floor.

Roll refrigerator back into place.

Check to see if the refrigerator is level.

Vacation and moving care

Short vacations

No need to shut off the refrigerator if you will be away for less than four weeks.

1. Use up any perishables.

2. Freeze other items.

3. If you have an automatic ice maker: l l l

Raise signal arm to OFF (up) position.

Shut off water supply to icemaker.

Empty the ice bin.


Long vacations

If you will be gone a month or more:

1. Remove all food from the refrigerator.

2. If you have an automatic ice maker: l

Turn off the water supply to the ice maker at least one day ahead of time. l When the last load of ice drops, turn off the ice maker. Make sure all ice has dispensed out of the ice maker mecha- nism.

3. Unplug the refrigerator.

4. Clean it, rinse well and dry.

5. Tape rubber or wood blocks to the tops of both doors to prop them open far enough for air to get in. This stops odor and mold from building up.


When you are moving the refrigerator to a new home:

1. If you have an automatic ice maker: l l

Turn off the water supply to the ice maker at least one day ahead of time.

Disconnect the water line. l

After the last load of ice drops, lift the signal arm to the OFF (up) position.

2. Remove all food from the refrigerator.

3. Pack all frozen food in dry ice.

4. Unplug the refrigerator.

5. Clean it thoroughly. Rinse well and dry.

6. Take out all removable parts, wrap them well, and tape them together so they don’t shift and rattle.

7. Screw in the leveling rollers.

6. Tape the doors shut and tape the power supply cord to the cabinet.

When you get to your new home, put everything back and refer to page 5. Also, remember to reconnect the water supply line.

To restart refrigerator, see “Using Your

Refrigerator” on page 7.

Power interruptions

If electricity goes off, call the power com- pany. Ask how long power will be off.

1. If service will be interrupted 24 hours or less, keep both doors closed. This helps food stay frozen.

2. If service will be interrupted longer than

24 hours:

(a) Remove all frozen food and store in a frozen food locker.


(b) Place 2 Ibs. (0.9 kg) of dry ice in freezer for every cubic foot of freezer space. This will keep food frozen for 2 to 4 days. Wear gloves to protect your hands from dry ice burns.


(c) If neither a food locker or dry ice is available, use or can perishable food at once.

3. A full freezer stays cold longer than a partly filled one. A freezer full of meat stays coM longer than a freezer full of baked goods. If food contains ice crystals, it may be safely refrozen, although the quality and flavor may be affected. If the condition of the fcod is poor, or if you feel it is unsafe, dispose of it.

Questions 7

Call our Consumer Assistance Center telephone number, 1-800-253-l 301.


Food Storage Guide

There is a correct way to package and store refrigerated or frozen food. To keep food fresher, longer, take the time to study these recommended steps.

Storing fresh food

Wrap or store&d placed in the refrigerator in airtight and moisture-proof material. This prevents food odor and taste transfer throughout the refrigerator. For dated products, check code date to ensure fresh- ness.

Leafy vegetables

Remove store wrapping and trim or tear off bruised and discolored areas. Wash in cold water and drain. Place in plastic bag or plastic container and store in crisper.

Vegetables with skins

(carrots. peppers)

Store in crisper, plastic bags or plastic container.


Wash, let dry and store in refrigerator in plastic bags or crisper. Do not wash or hull berries until they are ready to use. Sort and keep berries in their original container in a crisper, or store in a loosely closed paper bag on a refrigerator shelf.


Store without washing in egg bin provided, or in the original carton on an interior shelf.


Wipe milk cartons. For best storage, place milk on interiir shelf.

Butter or margarine

Keep opened butter in covered dish or closed compartment. When storing an extra supply, wrap in freezer packaging and freeze.


Store in the original wrapping until you are ready to use it. Once opened, rewrap tightly in plastic wrap or aluminum foil.


Cover leftovers with plastic wrap or alumi- num foil. Plastic containers with tight lids can also be used.


Store most meat in original wrapping as long as it is airtight and moisture-proof. Rewrap if necessary. See the following chart for storage times.



Ground beef

Steaks and roasts

Cured meats



1 to2

‘1 to2

3 to 5



Cold cuts

5 to 7

3 to 5

Variety meats 1 to 2

*If storing meat longer than the times given, follow the directions for freezing.

NOTE: Use fresh fish and shellfish the same day as purchased.


Storing frozen food

The freezer section is designed for storage of commercially frozen food and for freezing food at home.

NOTE: For further information about prepar- ing food for freezing or food storage times, contact your local Cooperative Extension

Service or check a freezer guide or reliable cookbook.


The secret of successful freezing is in the packaging. The way you close and seal the package must not allow air or moisture in or out. Packaging done in any other way could cause food odor and taste transfer through- out the refrigerator and drying of frozen food. l l l l l

Packaging recommended for use:

Rigid plastic containers with tight-fitting lids

Straight-sided canning/freezing jars

Heavy-duty aluminum foil

Plastic-coated paper

Non-permeable plastic wraps (made from a Saran film)

Follow package or container instructions for proper freezing methods. l l l l l l

Do not use:

Bread wrappers

Non-polyethylene plastic containers

Containers without tight lids

Waxed paper

Waxed-coated freezer wrap

Thin, semi-permeable wrap

The use of these wrappings could cause food odor, taste transfer and drying of frozen food.


Do not expect your freezer to quick-freeze any large quantity of food. Put no more unfrozen food into the freezer than will freeze within 24 hours (no more than 2 to

3 pounds of food per cubic foot of freezer space). Leave enough space for air to circulate around packages. Be careful to leave enough mom at the front so the door can close tightly.

Storage times will vary according to the quality of the food, the type of packaging or wrap used (airtight and moisture-proof) and the storage temperature, which should be

0°F (-17.8”C).


If You Need Assistance Or


Performance problems often result from little things you can fix without toots. Please read the chart below before calling for service on your appliance.

1. Before calling for assistance . . .

Listed in this chart are the most common problems consumers run into with their appliances.

Please read through this and see if it can solve your problem.


Your refrigerator Is the power supply cord firmty plugged into a live circuit with proper will not voltage? operate

Has a household fuse or circuit breaker blown/tripped?

The lights do not work

The ice maker does not work

Is the Refrigerator Control set to the OFF position?

Is the power supply cord firmly plugged into a live circuit with proper voltage?

Has a household fuse or circuit breaker blown/tripped?

Is a bulb burned out?

Is the freezer cold enough to make ice? It could take overnight for the freezer to reach the proper temperature.

Is the ON/OFF lever in the ON (down) position? (Seepage 13.)

Is the water valve turned on?

Does the water line have a cloa or leak?

You hear unfamil- Is something on top of or behind the refrigerator? iar sounds or a rattling/jingling

Some new sounds are normal. See “Understanding the sounds you noise may hear” on page 18.

There is water in This is normal on hot, muggy days. Make sure the refrigerator is level the defrost pan so the pan does not overflow.

The motor seems Are the condenser coils dirty? to run too much

Has the door been open often? Has a large amount of food been added at one time? The motor naturally runs longer if these things happen.

Is the room hot? If the room is too warm, the motor runs longer to keep the unit cool.


2. If you need assistance*...

Call Whirlpool Consumer Assistance

Center telephone number. Dial toll-free from anywhere in the U.S.A.:

1400-253-l 301 and talk with one of our trained consultants.

The consultant can instruct you in how to obtain satisfactory operation from your appliince or, if service is necessary, recom- mend a qualified service company in your area.

If you prefer, write to:

Mr. William Clark

Consumer Assistance Representative

Whirlpool Corporation

2000 M-63

Benton Harbor, Ml 49022

Please include a daytime phone number in your correspondence.

3. If you need service*...

Whirlpool has a nationwide network of authorized Whirlpoor service companies.

Whirlpool service technicians are trained to futfill the product warranty and provide after- warranty service, anywhere in the United

States. To locate the authorized Whirlpool service company in your area, call our

Consumer Assistance Center telephone number (see Step 2) or look in your tele- phone directory Yellow Pages under:



Seer WMrlpool Appliences or

Authorized Whklpml Sewlca

(fxempb;xYz .senice CO.) l WASHINO MACHINES k


-See: Whirlpool Appliances or

Aultmized Whirlpool !%-&a

(Erempb,xyz service Co.)

4. If you need FSP replace- ment parts . . .

FSP is a registered trademark of Whirlpool

Corporation for qualii parts. Look for this symbol of quality whenever you need a replacement part for your Whirlpoole appliance. FSP replacement Parts will fit right and work rigM, because they are made to the same exacting specifications used to build every new Whirlpool appliance.

To locate FSP replacement parts in your area, refer to Step 3 above or call the

Whirlpool Consumer Assistance Center number in Step 2.

5. If you are not satisfied with how the problem was solved . . .

l l

Contact the Major Appliance Consumer

Action Panel (MACAP). MACAP is a group of independent consumer experts that voices consumer views at the highest levels of the major appliance industry.

Contact MACAP only when the dealer, authorized servicer and Whirlpool have failed to resolve your problem.

Major Appliance Consumer Action Panel

20 North Wacker Drive

Chicago, IL 60606 l

MACAP will in turn inform us of your action.

1 ‘When asking for help or service:

Please provide a detailed description of the problem, your appliance’s complete model and serial numbers, and the pur- chase date. (See page 2.) This informa- tion will help us respond properly to your request.



Refrigerator Warranty




From Date of Purchase



From Date of Purchase


FSP@ replacement parts and repair labor to correct defects in materials or workmanship. Service must be provided by an authorized Whirlpool service company.

FSP replacement parts and repair labor to correct defects in materials or workmanship in the sealed refrigeration system. These parts are:

1. Compressor

2. Evaporator

4. Drier

5. Connecting tubing

3. Condenser

Service must be provided by an authorized Whirlpool service company.


A. Service calls to:

1. Correct the installation of your refrigerator.

2. Instruct you how to use your refrigerator.

3. Replace house fuses or correct house wiring or plumbing.

4. Replace light bulbs.

B. Repairs when your refrigerator is used in other than normal, single-family household use.

C. Pickup and delivery. Your refrigerator is designed to be repaired in the home.

D. Damage to your refrigerator caused by accident, misuse, fire, flood, acts of God or use of products not approved by Whirlpool.

E. Any food loss due to product failure.

F. Repairs to parts or systems caused by unauthorized modifications made to the appliance. s-83


QUENTIAL DAMAGES. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Outside the United States, a different warranty may apply. For details, please contact your authorized Whirlpool distributor or military exchange.

If you need service, first see the “Assistance or Service” section of this book. After checking

“Assistance or Service,” additional help can be found by calling our Consumer Assistance

Center telephone number, 1-800-253-1381, from anywhere in the U.S.A.

PART NO. 2170728

0 1883 Whirlpool Corporalion

Prlnkd on rHy&cl lw% pas-wnsumr paper- wale

50% recovered materials

@J Regtskrea Trademark I TM Trademark of Whirlpool Corpwation Printed in U.S.A


Related manuals

Frequently Answers and Questions

How much space should be around the refrigerator for proper installation?
Allow 1.25 cm space on each side and at the top of the refrigerator for ease of installation.
If the refrigerator is against a wall, which side should have more space?
The hinge side closest to the wall should have extra space to allow the door to be opened wider.
How to level the refrigerator?
Adjust the leveling screws at the front of the refrigerator. Turn the screw clockwise to raise the front, counterclockwise to lower it.
What is the recommended temperature setting for the refrigerator?
For normal household usage, set the Refrigerator Control to 3 and the Freezer Control to B.
How to adjust the temperature if needed?
First adjust the Refrigerator Control and wait 24 hours. If needed, then adjust the Freezer Control.
How to remove a refrigerator shelf?
Remove items from the shelf, tilt the front of the shelf up, lift the back of the shelf up, and pull the shelf straight out.
How to adjust the shelf glide?
Grasp the glide, slide it along the track to the desired position.
What is the purpose of the egg bin?
The egg bin is designed to store eggs safely and conveniently.
How to remove the base grille?
Grasp the grille from both sides, pull it straight towards you, then lift it up.
How to change the light bulbs?
Unplug the refrigerator. Remove the light shield by pushing up on the tabs and pulling the shield toward you. Then, turn the bulb counterclockwise and remove it.