Siqura 1002 BL1002F4-EI, CD1002F2-EI, FD1002V1-EI IP camera User Manual
The Siqura 1002 BL1002F4-EI, 1002 CD1002F2-EI, 1002 FD1002V1-EI IP cameras offer a wide range of capabilities for security surveillance. These cameras provide high-resolution video capture, advanced video analysis features, and reliable connectivity. Users can view live video streams, record events, and remotely manage the cameras through a user-friendly web interface.
Advertisement
Advertisement
Siqura 1002 Series
3 MP Intelligent IP cameras
BL1002F4-EI / CD1002F2-EI / FD1002V1-EI
Note: To ensure proper operation, please read this manual thoroughly before using the product and retain the information for future reference.
Copyright © 2016 Siqura B.V.
All rights reserved.
BL1002/CD1002/FD1002
User Manual v1 (162807-1)
AIT55
Nothing from this publication may be copied, translated, reproduced, and/or published by means of printing, photocopying, or by any other means without the prior written permission of Siqura.
Siqura reserves the right to modify specifications stated in this manual.
Brand names
Any brand names mentioned in this manual are registered trademarks of their respective owners.
Liability
Siqura accepts no liability for claims from third parties arising from improper use other than that stated in this manual.
Although considerable care has been taken to ensure a correct and suitably comprehensive description of all relevant product components, this manual may nonetheless contain errors and inaccuracies. We invite you to offer your suggestions and comments by email via [email protected]. Your feedback will help us to further improve our documentation.
How to contact us
If you have any comments or queries concerning any aspect related to the product, do not hesitate to contact:
Siqura B.V.
Zuidelijk Halfrond 4
2801 DD Gouda
The Netherlands
General : +31 182 592 333
Fax : +31 182 592 123
E-mail : [email protected]
WWW : www.siqura.com
2
Contents
Safety and compliance ..............................................................................
Safety instructions ...............................................................................
Compliance information ........................................................................
System requirements ...........................................................................
Connect the camera to a LAN ................................................................
Connect the camera to a WAN ...............................................................
Get access to the camera ..........................................................................
Get access via web browser ..................................................................
Get access via Siqura Device Manager ....................................................
Get access via UPnP .............................................................................
Log on to the camera ...........................................................................
Install the videoplayer plug-in ...............................................................
Basic information .................................................................................
Time settings ......................................................................................
Upgrade and maintenance ....................................................................
Local configuration ...............................................................................
User Management ................................................................................
Authentication .....................................................................................
IP Address Filter ..................................................................................
Streaming ..........................................................................................
Picture adjustment ...............................................................................
Privacy mask ......................................................................................
3
Contents
Motion Detection .................................................................................
Video Tampering .................................................................................
Intrusion Detection ..............................................................................
Line Crossing Detection ........................................................................
HDD Management ................................................................................
Record Schedule ..................................................................................
4
1 About this manual
What's in this manual
This is version 1 of the user assistance which is embedded in the web interface of the BL1002/
CD1002/FD1002 series camera. The Help topics give you all the information you need for using this product efficiently. They tell you:
● How to get access to the camera
● How to communicate with the camera
● How to operate the camera
● How to configure the settings of the camera
Where to find more information
The technical specifications of this product are given in the BL1002/CD1002/FD1002 datasheet. All manuals (including this user assistance) and datasheets for Siqura products are available as PDF download at www.siqura.com. We advise you to make sure that you have the latest version of this manual.
Who this manual is for
These instructions are for all professionals who will configure and operate Siqura BL1002/
CD1002/FD1002 series cameras.
What you need to know
You will have a better understanding of how the camera works if you are familiar with:
● Camera technologies
● CCTV systems and components
● Ethernet network technologies and Internet Protocol (IP)
● Windows environments
● Video, audio, data, and contact closure transmissions
● Video compression methods
Before you continue
Before you continue, read and obey all instructions and warnings in this manual. Keep this manual with the original bill of sale for future reference and, if necessary, warranty service.
When you unpack your product, make sure there are no missing or damaged items. If any item is missing, or if you find damage, do not install or operate this product. Ask your supplier for assistance.
Why specifications may change
At Siqura, we are committed to delivering high-quality products and services. The information given in this manual was current when published. As we continuously seek to improve our products and user experience, all features and specifications are subject to change without notice.
We like to hear from you!
Customer satisfaction is our first priority. We welcome and value your opinion about our products and services. Should you detect errors or inaccuracies in this manual, we would be grateful if you would inform us. We invite you to offer your suggestions and comments via [email protected]. Your feedback helps us to further improve our documentation.
5
2
2.1
Safety and compliance
This section provides safety instructions and compliance information.
In This Chapter
Safety instructions
These instructions are intended to make sure that the user can use the product correctly and avoid danger or property loss.
The precaution measure is divided into ‘Warnings’ and ‘Cautions’:
● Warnings: Serious injury or death may be caused if any of these warnings are neglected.
● Cautions: Injury or equipment damage may be caused if any of these cautions are neglected.
Warnings
Follow these safeguards to prevent serious injury or death.
Cautions
Follow these precautions to prevent potential injury or material damage.
Warnings
● Use a power adapter which can meet the safety extra low voltage (SELV) standard and source it with 12 Vdc or 24 Vac (depending on the model) according to the IEC60950-1 and Limited Power Source standard.
● To reduce the risk of fire or electrical shock, do not expose this product to rain or moisture.
● This installation should be made by a qualified service person and should conform to all the local codes.
● Install blackout equipment into the power supply circuit for convenient supply interruption.
● Make sure that the ceiling can support more than 50 (N) Newton if the camera is fixed to the ceiling.
● If the product does not work properly, contact your dealer or the nearest service centre. Never attempt to disassemble the camera yourself. We shall not assume any responsibility for problems caused by unauthorised repair or maintenance.
6
Safety and compliance
Cautions
● Make sure the power supply voltage is correct before using the camera.
● Do not drop the camera or subject it to physical shock.
● Do not touch the sensor modules with your fingers. If cleaning is necessary, use a cleaning cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period of time, put on the lens cap to protect the sensor from dirt.
● Do not aim the camera lens at strong light such as the sun or an incandescent lamp. The strong light can cause fatal damage to the camera.
● The sensor may be burned out by a laser beam, so if any laser equipment is used, make sure that the surface of the sensor is not exposed to the laser beam.
● Use the unit under conditions where the temperature remains within the range given in the Technical Specifications of this product. You can download the datasheet of the camera at www.siqura.com.
● Do not install the camera in a dusty or damp environment, and do not expose it to high electromagnetic radiation.
● To avoid heat accumulation, good ventilation is required to ensure a proper operating environment.
● Keep the camera away from water and any liquid.
● While shipping, the camera should be packed into its original packing.
● Improper use or replacement of the battery may result in the hazard of explosion. Use the battery type recommended by the manufacturer.
Cautions
The following cautions apply to cameras with IR functionality. Be sure to follow them to prevent IR reflection.
● Dust or grease on the dome cover will cause IR reflection. Do not remove the dome cover film until the installation is finished. If there is dust or grease on the dome cover, clean the dome cover with a clean soft cloth and isopropyl alcohol.
● Make sure that the installation location does not have any reflective surfaces of objects that are too close to the camera. The IR light from the camera may reflect back into the lens causing a reflection in the video image.
● The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS. Fasten the dome cover to the camera body so that the foam ring and the dome cover are attached seamlessly.
7
Safety and compliance
2.2
Compliance information
FCC compliance
This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Conditions
1
2
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonised European standards listed under the EMC Directive
2004/108/EC, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European
Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury
(Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.
8
3
3.1
Connect to network
This section gives instructions for connecting the camera to the network.
In This Chapter
System requirements
To open communication with the camera, you need:
● A computer with a web browser installed.
● An IP connection between the computer and the camera.
Computer
The browsing computer should meet the following minimum system requirements:
Item
Operating System
CPU
RAM
Display
Web browser
Description
Microsoft Windows 7 / Server 2008 32 bits
Intel Pentium IV 3.0 GHz or higher
1 GB or higher
1024×768 resolution or higher
Internet Explorer 7.0 and higher, Apple Safari 5.02 and higher,
Mozilla Firefox 5 and higher, and Google Chrome 8 and higher
IP connection
You can connect the network camera to:
● A local area network (LAN)
● A wide area network (WAN)
Note: Be aware that using this product with Internet access may pose serious threats to your network security. To avoid network attacks and information leakage, strengthen your security against intrusions. To ensure the network security of the network camera, we advise you to inspect and maintain the network camera at specific intervals. If the product does not work properly, contact your sales representative.
9
Connect to network
3.2
Connect the camera to a LAN
To view and configure the camera via a LAN, you need to connect the network camera in the same subnet with your computer, and install the Siqura Device Manager software to search and change the IP of the network camera. Siqura Device Manager is available for download at www.siqura.com/support-files.
The following figures show the two ways of cable connection of a network camera and a computer:
● To test the network camera, you can directly connect the network camera to the computer with a network cable as shown below.
● Refer to the picture below to set the network camera over the LAN via a switch or a router.
Bring the camera and computer into the same subnet
2
3
Take the following steps to connect to the network camera from the computer:
1 Set the network adapter of the computer to the factory-set subnet of the camera.
(Control Panel > Network and Sharing Center > Change adapter settings ... >
Properties ... )
For the default network settings of the camera, see Default settings (below) .
Connect the two devices with a network cable.
Open the web interface of the camera from a web browser on the computer.
For details, see Get access via web browser.
For information about Siqura Device Manager, see Get access via Siqura Device
Manager.
Default settings
Out of the box, the camera has these settings:
● DHCP: enabled
● UPnP: enabled
● Logon: not required
Note: If no DHCP server is found on the network, the camera is initially assigned the IP address 0.0.0.0. After 30 seconds, an IP address in the range of
192.168.1.2~192.168.1.253 is adopted.
10
Connect to network
Add the camera to the intended subnet
3
4
5
1
2
Via the web interface of the camera, you can change its network settings to add it to the subnet it will be used in.
On the Network page, click the TCP/IP tab.
Set the IP address of the camera to the desired subnet.
Click Save.
Reboot the camera.
(Optional) Configure the network settings of the computer to assign it to the subnet set in step 2.
With both devices on the same subnet, you can reopen communication between the computer and the camera.
3.3
Connect the camera to a WAN
This section explains how to connect the network camera to the WAN with a static IP or a dynamic IP.
Static IP connection
Before you start, obtain a static IP address from an Internet Service Provider (ISP). With the static IP address, you can connect the network camera via a router or connect it to the WAN directly.
To connect the network camera via a router
1
2
3
4
5
Establish a connection between the network camera and the router.
Assign a LAN IP address, subnet mask and gateway address.
For more information about the IP address configuration of the camera, see Wiring over
the LAN.
Save the static IP in the router.
Set the port mapping.
Use 80, 8000, and 554 as ports, for example.
The steps for port mapping vary according to the different routers. If necessary, contact the router manufacturer for assistance with port mapping
Visit the network camera through a web browser or client software over the internet.
Directly connect the network camera with a static IP address
You can also save the static IP on the camera and directly connect it to the internet without using a router.
11
Connect to network
Dynamic IP connection
Before you start, obtain a dynamic IP address from an Internet Service Provider (ISP). With the dynamic IP address, you can connect the network camera via a modem or a router.
3
4
5
6
7
Connect the network camera via a router
1
2
Establish a connection between the network camera and the router.
On the camera, assign a LAN IP address, subnet mask and gateway address.
For more information about the IP address configuration of the camera, see Wiring over
the LAN.
In the router, set the PPPoE user name, password and confirm the password.
Set the port mapping.
Use 80, 8000, and 554 as ports, for example.
The steps for port mapping vary according to the different routers. If necessary, contact the router manufacturer for assistance with port mapping.
Apply a domain name from a domain name provider.
Configure the DDNS settings in the setting interface of the router.
Visit the camera via the applied domain name.
Connect the network camera via a modem
This camera supports the PPPoE auto dial-up function. The camera gets a public IP address by
ADSL dial-up after the camera is connected to a modem. You need to configure the PPPoE parameters of the network camera.
The obtained IP address is dynamically assigned via PPPoE, so the IP address always changes after rebooting the camera. To solve the inconvenience of the dynamic IP, you need to get a domain name from the DDNS provider. Follow the steps below to set a normal domain name resolution and a private domain name resolution to solve the problem.
Normal domain name resolution
1
2
3
Apply a domain name from a domain name provider.
On the DDNS tab of the Network page in the camera, configure the DDNS settings.
Visit the camera via the applied domain name.
12
Connect to network
Private domain name resolution
3
4
1
2
Install and run the IP Server software on a computer with a static IP.
Access the network camera through the LAN through a web browser.
On the DDNS tab of the Network page in the camera, select Enable DDNS.
In the DDNS Type list, select IPServer.
13
4
4.1
Get access to the camera
The webpages of the camera offer a user-friendly interface for configuring its settings and viewing live video over the network. This section explains how to log on to the built-in web server.
In This Chapter
Get access via web browser
Default settings
Out of the box, the camera has these settings:
● DHCP: enabled
● UPnP: enabled
● Logon: not required
If a DHCP server exists on the network, the camera acquires an IP address from the DHCP address range. If necessary, refer to your system administrator for assistance.
If no DHCP server is found on the network, the camera is initially assigned the IP address
0.0.0.0. After 30 seconds, an IP address in the range of 192.168.1.2~192.168.1.253 is adopted.
1
2
3
To connect to the camera via your web browser
Open your web browser.
Type the IP address of the camera in the address bar.
Press ENTER.
The Live View page is opened.
- or -
If user accounts exist on the camera, you are directed to the login page (see Log on to
the camera).
Note: If you do not know the IP address of the camera you can use Siqura Device Manager or UPnP, both described in the following sections, to detect the camera on the network.
14
Get access to the camera
4.2
Get access via Siqura Device Manager
Siqura Device Manager is a Windows-based software tool that you can use to manage and configure Siqura IP cameras and video encoders. The tool automatically locates Siqura devices on the network and offers you an intuitive interface to set and manage network settings, configure devices, show device status, and perform firmware upgrade.
1
2
3
To install Siqura Device Manager
Download the latest version of Siqura Device Manager at www.siqura.com/support-files.
Double-click the setup file.
Follow the installation steps to install the software.
1
2
3
4
5
6
To connect to the camera via Siqura Device Manager
Start Siqura Device Manager
The network is scanned.
Detected devices appear in the List View pane.
If multiple network adapters exist, select the appropriate adapter to scan the network that you wish to connect to.
To perform a manual search, click the Rescan button.
Use the tabs in the Tree View pane to define the scope of your search.
Click the column headings in the List View pane to sort devices by type, IP address, or name.
To connect to the webpages of the camera, double-click its entry in the device list,
The Live View page is opened
- or -
If user accounts exist on the camera, you are directed to the login page. (see Log on to
the camera).
Change the network settings with Siqura Device Manager
With Siqura Device Manager, you can directly change the network settings of the camera.
1
2
3
To assign a static IP address
Go to the list of detected devices, and then right-click the entry for the camera.
Click Change Network Settings.
In Change Network Settings, click Static IP.
15
Get access to the camera
4
5
6
7
Provide the camera with an appropriate IP address, netmask, and gateway address for the desired network configuration, and then click OK.
In the pop-up window indicating that you have successfully changed the settings, click
OK.
Wait one minute, and then rescan the network.
To access the webpages of the camera, double-click its entry in the list of found devices.
4.3
To assign a DHCP server
3
4
5
1
2
6
Record the MAC address of the camera (see the Serial no. column in Siqura Device
Manager) for future identification
In the list of detected devices, right-click the device with the network property that you would like to change.
Click Change Network Settings.
In Change Network Settings, click Enable DHCP, and then click OK.
In the pop-up window indicating that you have successfully changed the settings, click
OK.
Wait one minute, and then rescan the network.
You can identify the camera by its MAC address.
To access the webpages of the camera, double-click its entry in the list of found devices.
7
Note: A DHCP server must be installed on the network in order to provide DHCP network support. If no DHCP server is found on the network, the camera is initially assigned the IP address 0.0.0.0. After 30 seconds, an IP address in the range of
192.168.1.2~192.168.1.253 is adopted.
Get access via UPnP
Universal Plug and Play (UPnP) support is enabled by default on the camera. With the UPnP service enabled in Windows, you can get access to the camera from Windows Explorer.
1
2
To connect to the camera via UPnP
In Windows Explorer, open the Network folder.
Detected devices in the same subnet as the computer are displayed, including Siqura codecs and cameras with UPnP support.
Double-click the camera that you want to connect to.
The Live View page is opened.
- or -
16
Get access to the camera
If user accounts exist on the camera, you are directed to the login page (see Log on to
the camera).
4.4
Log on to the camera
By default, users can freely open the web interface of the camera.
Admin account
Out of the box, users do not need to log on to the web interface of the camera. RTSP
Authentication and Illegal Login Lock are disabled. There is a built-in "Admin" user account with password "1234" which is intended for API calls only.
Important: To avoid being locked out of the camera, Siqura strongly advises against installers creating an Admin account and setting a password when installing the camera.
Create a new account with Administrator level when you start using the camera. The initial, built-in Admin account is then no longer available. After that, you can add "Operator" and
"User" accounts.
CAUTION: TO KEEP THE ACCOUNT SAFE, SET A STRONG, COMPLEX PASSWORD. THIS
HELPS TO PREVENT UNAUTHORISED ACCESS FROM PEOPLE WHO TRY TO USE THE DEFAULT
ACCOUNT.
To create a strong password
● Use at least eight characters
● Do not include your real name, user name, company name, or other personal information
● Do not use complete words that can be found in a dictionary
● Use a random combination of at least two of the following categories: upper case letters, lower case letters, numbers and special characters
Note: For better protection, especially in high-security systems, we advise you to change the password at regular intervals.
Login box
Once the initial admin account has been replaced, you will encounter a login box when you connect. You are prompted to supply your user name and password. Only users with a valid account can log on.
17
Get access to the camera
4.5
Note: The IP address of the camera gets locked after seven failed passwords attempts for the admin and five attempts for the user/operator.
Install the videoplayer plug-in
For (live) video viewing and operating the camera, a videoplayer plug-in is needed. If the plug-in is not detected you are prompted to download and install it.
3
4
1
2
5
6
7
8
To install the plug-in
Click the hyperlink in the webpage of the camera.
Save the WebComponents.exe file to your Downloads folder.
Close your web browser.
Go to your Downloads folder.
Double-click WebComponents.exe.
The executable file does not give rise to any security risks. You can install it safely.
Follow the installation steps.
Open your web browser.
Reconnect to the camera.
18
5 Live View
The Live View page is the home page of the web interface. It is shown when you successfully connect to the camera.
What this page is for
On the Live View page, you can view real-time video, capture images and configure various video settings.
1. Title bar 2. Menu 3. Live View window 4. Toolbar
Title bar
The horizontal bar at the top of the window has the following items.
Item Description
Shows the brand of the camera you are connected to
Shows the camera model name
Shows the user currently logged in*
Opens the Online Help information
Logs out the current user*
*Shown if login was required
19
Live View
Menu
The vertical menu on the left gives access to the pages of the web interface.
Live View window
This area is used to display live video from the connected camera.
Toolbar
The horizontal bar at the bottom of the page contains buttons on the left and on the right.
Buttons (left side) Description
Opens the Aspect Ratio list. This is where you set the relation between the width and height of the video display.
Sets the video aspect ratio to 4:3
Sets the video aspect ratio to 16:9
Sets the original video aspect ratio
Sets the video aspect ratio to Auto mode (self-adaptive resizing)
Opens the Stream Type list. Use the options to select a video stream for display in the Live View window.
Selects Stream 1
Selects Stream 2
Opens the video player plug-in list. Use the options to select a plug-in or live video display.
Selects the Webcomponents plug-in
Selects the QuickTime plug-in
Buttons (right side) Description
Stops Live View (screen goes blank)
Starts Live View
Captures the image
Starts a recording
Stops a recording
Enables digital zoom (e-PTZ)
Disables digital zoom (e-PTZ)
20
Live View
Manual recordings and snapshots
Clicking Start Recording starts a manual recording. The recording is saved to the location set via the Local Configuration tab of the System page. There, you can also set the storage path for captured snapshots.
Important: To use this function, run your web browser as Administrator.
Full-screen mode
You can double-click on the live video to go from the current live view mode to full-screen or return to normal mode from full-screen.
21
6 Playback
What this page is for
On the Playback page, you can view recorded video stored on a network disk or on the SD card.
1
2
3
To search for recorded video
On the Playback page, go to the calender on the right.
Select the date you need.
Click Search.
Video recordings for this date - if any - appear in the Time line at the bottom of the page.
Recording types - Command, Continuous, Events, and Manual - can be distinguished by their colour.
The progress pointer is positioned at the start of the first recording.
To locate a specific playback point
● In Set playback time, type the exact time, and then click Enter.
- or -
● Drag the Time line to the left or right, relative to the pointer.
You can click the "-" and "+" button to zoom the Time line.
Video playback
For video playback, use the following buttons in the Playback toolbar.
22
Playback
Task
To start playback
To pause playback
To stop playback
To accelerate playback speed
To reduce playback speed
Action
Click Start
Click Pause
Click Stop
Click Fast forward
Click Slow forward
Button
To advance one frame Click Single frame
Additional functions
The buttons below are located on the right side of the toolbar.
Task Action Button
To capture a snapshot Click Capture
To create a video clip
To use digital zoom (e-PTZ)
To download an image or recording
Click Start/Stop
clipping
Click Enable/Disable e-
PTZ
Click Download
23
7
7.1
System
The System page is the central place for viewing and configuring device and firmware related information and settings. On the various tabs, you can adjust the time settings, reboot the camera, restore the default settings, upgrade the firmware, view logs, and configure local settings.
In This Chapter
Basic information
System > Basic Information
What this tab is for
The Basic Information tab gives general information about the camera. It is made up of editable and non-editable content.
Identification
For easier identification of the camera on the network, assign a device name and device number to the camera.
1
2
3
To assign a device name and device number
In Device Name, type a (user-friendly) name for the camera.
In Device No., type the camera number.
Click Save.
24
System
7.2
Reference information
The non-editable content on this tab serves as reference information for maintenance or future configuration of the camera. Note that this information varies per model.
Time settings
System > Time Settings
What this tab is for
On the Time Settings tab, you can set the device date and time manually or use an NTP server. You can also configure the Daylight Saving Time (DST) settings here.
To set the time zone
1
2
3
Click to open the Time Zone list.
Select the location of the camera.
Click Save.
Note: The Time Zone list is not available if Sync. with computer time is selected.
3
4
1
2
To synchronise the system time with a Network Time Protocol (NTP) server
In the NTP section,click NTP.
In Server Address, type the IP address of the NTP server.
In NTP Port, type the port number of the NTP server.
In Interval, type the time interval (in minutes) between the consecutive time service queries.
25
System
5
The interval between two synchronising actions by an NTP server can be set from 1 to
10080 minutes.
Click Test.
The connection to the time server is tested.
If your settings are correct, click Save.
6
Note: If the camera is connected to a public network, use an NTP server that has a time synchronisation function. If the camera is set up in a customised network, NTP software can be used to establish an NTP server for time synchronisation.
3
4
1
2
5
6
To set the system time manually
In the Manual Time Sync section, select Manual Time Sync.
In Set Time, click the Calender/Clock icon.
Use the calender and the Time list to set the system date and time.
Click OK to confirm your settings.
(Optional) As an alternative to steps 2-4, you can select Sync. with computer time.
This synchronises the camera system time with the time of your computer.
Click Save.
1
2
3
4
To enable DST
In the DST section, select Enable DST.
In the Start Time and End Time lists, select the appropriate start and end details.
In the DST Bias list, select the offset.
This is the amount of time you need to subtract from or add to Coordinated Universal time (UTC) to get the current time for the location of the camera.
Click Save.
26
System
7.3
Upgrade and maintenance
System > Upgrade & Maintenance
What this tab is for
Use the Upgrade & Maintenance tab for the following tasks:
● Reboot the camera
● Restore the factory-default camera settings,
● Export/Import a camera configuration file
● Upgrade the camera firmware
Reboot the camera
If there are connectivity problems or if an error occurs, reboot the camera. A reboot does not affect the settings of the camera.
To reboot the camera
1
2
Click Reboot.
Click OK to confirm.
The webpage is unresponsive while the camera is rebooting.
Restore default settings
With the options in the Default section, you can restore the camera settings to their original factory-default values. Depending on the option you select, the reset includes or excludes the current network settings and user information.
To restore the default settings
● Click Restore to reset all settings with the exception of the network settings and the user information.
27
System
- or -
● Click Default to perform a complete reset including the network settings and user information.
Use this button with caution.
Warning: Clicking Default can make the camera unreachable for in-band communications.
In that case you can only get access to the web interface by (temporarily) moving a PC to the factory-default subnet of the camera.
Use a configuration file
If you want to apply the same settings to a batch of cameras, use a configuration file to simplify the process. You configure a camera with the required settings, export the settings in a configuration file and import this file on the other cameras.
3
4
1
2
To export a configuration file
Click Device Parameters.
Browse to the folder where you want to store the file.
Specify a file name.
Click Save.
To import a configuration file
3
4
1
2
5
6
In the Import Config. File section, click Browse.
Browse to the folder where the file is stored.
Select the file.
Click Open.
Click Import.
Reboot the camera when the import has completed.
Upgrade the system
We advise you to visit www.siqura.com and check if new firmware for your camera is available. To upgrade the system, download the latest firmware file to your computer and complete the steps below.
To upgrade the system
1
2
3
4
In the Upgrade section, click Firmware.
Click Browse.
Locate and select the firmware file.
It is essential that the selected file is compatible with the camera.
Click Upgrade.
The upgrade process takes 1~10 minutes. Do not disconnect the power of the camera during the process. The camera reboots automatically after the upgrade.
Note: It is also possible to select Firmware Directory in step 1. In that case, you need to find the directory where the firmware is stored. The device can find the firmware in the directory automatically.
28
System
7.4
Log
System > Log
What this tab is for
On the Log tab, you can view and export information kept in the Alarm, Exception, Operation, and Information logs of the camera. This information is often useful when you are troubleshooting occurred issues.
Before you start
Configure network storage for the camera or insert an SD card into the camera.
1
2
3
4
To perform a search
In the Major Type and Minor Type lists, select the filter type to be applied.
Use Start Time and End Time lists to set the date/time range.
Click Search.
The results of your search are shown in the Log List.
To export the search results, click Export.
Exports can be saved as Text files or Excel files.
29
System
7.5
Local configuration
System > Local Configuration
What this tab is for
On the Local Configuration tab, you can configure Live View settings and set the paths to the storage folders for snapshots, clips and downloads.
Live View Parameters
Use this section to set the protocol type and live view performance.
1
2
3
4
To configure the Live View parameters
Select the protocol to be used.
TCP: Ensures complete delivery of streaming data and better video quality. Real-time transmission will be affected, though.
UDP: Provides real-time audio and video streams.
Multicast: For information about multicast, see the description of the TCP/IP tab of the
Network page.
HTTP: Provides the same quality as the TCP option without setting specific ports for streaming under some network environments.
Set Play Performance to Shortest Delay or Auto.
Set Rules to Enable or Disable.
This setting determines the behaviour of your local browser. To have the coloured overlays shown or hidden when motion detection, face detection, or intrusion detection is triggered, select Enable or Disable, respectively. With Rules and face detection both enabled, faces are marked with a green rectangle in Live View once they are detected.
Select the image format to be used for captured pictures.
30
System
Record File Settings
Use this section to set the file size and the paths to the storage folders for video you recorded with your web browser.
To set the file size and the paths to your storage
1
2
3
Set the packed size of manually recorded and downloaded video files to 256M, 512M or
1G.
This sets the maximum file size for recordings to the selected value.
In Save record file to, type the storage path for manually recorded files or use the
Browse button.
In Save downloaded files to, type the storage path for video files downloaded in playback mode or use the Browse button.
Picture and Clip Settings
Use this section to set the paths to the storage folders for snapshots and video clips you captured with your web browser.
1
2
3
4
To set the paths to your storage
To set the storage path for pictures manually captured in Live View mode, type the path in the Save snapshots in live view to box or use the Browse button.
In Save snapshots when playback to, type the storage path for pictures captured in
Playback mode or use the Browse button.
In Save clips to, type the storage path for video clipped in Playback mode or use the
Browse button.
Click Save.
31
8
8.1
Security
On the Security page, you can manage user accounts, configure authentication settings and enable an IP address filter.
In This Chapter
User Management
Security > User Management (Administrator account created)
What this tab is for
The User Management tab is the place where the admin user adds, modifies and deletes user accounts.
Admin account
Out of the box, users do not need to log on to the web interface of the camera. RTSP
Authentication and Illegal Login Lock are disabled. There is a built-in "Admin" user account with password "1234" which is intended for API calls only.
Important: To avoid being locked out of the camera, Siqura strongly advises against installers creating an Admin account and setting a password when installing the camera.
Create a new account with Administrator level when you start using the camera. The initial, built-in Admin account is then no longer available. After that, you can add "Operator" and
"User" accounts.
CAUTION: TO KEEP THE ACCOUNT SAFE, SET A STRONG, COMPLEX PASSWORD. THIS
HELPS TO PREVENT UNAUTHORISED ACCESS FROM PEOPLE WHO TRY TO USE THE DEFAULT
ACCOUNT.
To create a strong password
● Use at least eight characters
● Do not include your real name, user name, company name, or other personal information
● Do not use complete words that can be found in a dictionary
● Use a random combination of at least two of the following categories: upper case letters, lower case letters, numbers and special characters
32
Security
8.2
Note: For better protection, especially in high-security systems, we advise you to change the password at regular intervals.
User management
Up to 31 user accounts can be created. Two user levels are available: Operator and User. Per user, different permissions can be assigned.
5
6
3
4
1
2
To add a user account
Click Add.
Type the user name.
In the Level list, select Operator or User.
Type the password.
For information about strong passwords, see above.
Select and/or clear the permissions for the new user, as required.
Click OK.
3
4
1
2
5
To modify a user account
Select the user in the User List.
Click Modify.
Change the user name, level or password as needed.
Select or clear permissions as needed.
Click OK.
1
2
3
To delete a user account
Select the user in the User List.
Click Delete.
Click OK.
Authentication
Security > Authentication
What this tab is for
On the Authentication tab, you can enable/disable the following functions:
● Authentication for users who want to extract an RTSP video stream from the camera
● Access for users who do not have a user account for the camera
● Data communication security
● Illegal login lock
33
Security
8.3
RTSP Authentication
From a security perspective, it may be undesirable that users can freely connect to the camera over RTSP to view a video stream. With RTSP Authentication, it is possible to restrict access to users with a valid account. On attempting to start an RTSP stream, users are prompted to provide a user name and password.
To configure RTSP Authentication
1
2
In the RTSP Authentication list, select basic or disable as required.
Click Save.
Important: If you disable RTSP Authentication, anyone can use a connection over RTSP to start a video stream via the IP address of the camera.
Security service
With SSH enabled, the data communication is encrypted and compressed to improve security and reduce the transmission time.
To turn on the security service
1
2
Select Enable SSH.
Click Save.
Illegal login prevention
It is possible to have the camera locked if an operator/user user enters an incorrect user name or password for five consecutive times. The admin is locked out after seven failed logon attempts. If the camera is locked, you can try to log on again after 30 minutes.
1
2
To turn on the illegal login lock
Select Enable Illegal Login Lock.
Click Save.
IP Address Filter
Security > IP Address Filter
34
Security
What this tab is for
On the IP Address Filter tab, you can deny/allow access to the camera from specific IP addresses.
1
2
3
4
To turn on the IP address filter
Select Enable IP Address Filter.
In the IP Address Filter Type list, select Forbidden or Allowed, as required.
Forbidden: Forbid the IP addresses added in the IP Address Filter list to log in.
Allowed: Allow only the IP addresses added in the IP Address Filter list to log in.
Set up the IP Address Filter list (see below).
Click Save.
3
4
1
2
To add an IP address
Click Add.
Type the IP address.
Click OK.
Click Save.
3
4
1
2
5
To modify an IP address
Select the IP address in the list.
Click Modify.
Type the new IP address.
Click OK.
Click Save.
1
2
3
To delete an IP address
Select the check box of the IP address in the list.
To select all IP addresses, click the header row check box.
Click Delete.
Click Save.
35
9
9.1
Network
On the Network page, you can configure the TCP/IP, DDNS, SNMP, 802.1X, QoS, NAT, HTTPS,
Mail, and FTP settings of the camera.
In This Chapter
TCP/IP
Network > TCP/IP
36
Network
What this tab is for
On the TCP/IP tab, you can configure the basic network settings, the DNS server settings and the port settings.
Basic settings
The TCP/IP settings must be properly configured before you operate the camera over the network. The camera supports the IPv4 and IPv6 protocols. Both versions may be configured simultaneously without conflicting each other. At least one IP version should be configured.
To configure the basic network settings
1
2
3
4
5
In the NIC Type list, select the appropriate network adapter type.
If the IP address will be assigned via a DHCP server, select DHCP.
This makes the IPv4 and DNS Server boxes unavailable.
In IPv4 Address, type the IP address.
This is the fixed IP address that will be used for the camera.
In IPv4 Subnet Mask, type the subnet mask.
This is used to determine to what subnet the camera belongs.
In IPv4 Default Gateway, type the IP address of the default gateway.
This is the device that passes traffic from the local subnet to other subnets and networks.
6
7
8
Click Test.
This is to determine if the chosen IP address is available on the network.
If you use IPv6, select the required mode in the IPv6 Mode list.
With Manual mode selected, you need to specify the IP address, subnet mask and default gateway.
If you select Route Advertisement, the router must support this function.
In MTU, type the Maximum Transmission Unit (MTU) size.
This is the maximum size of an IP packet that can be sent over the network without dividing it into pieces. The valid MTU size range is 1280 ~ 1500. The default value is
1500 (Ethernet). The value you type here must be supported on the other side of the connection.
In Multicast Address, type the multicast IP address to be used.
9
Multicast can be used to send a media stream from the camera to a group of interested receivers in a single transmission. The stream is sent to the multicast group address and multiple clients can acquire the stream at the same time by requesting a copy from the multicast group address. The switches and other network devices must be carefully configured for, and capable of handling multicasting and its protocols (most notably
IGMP).
10 (Optional) Select Enable Multicast Discovery.
If selected, the online network camera can be automatically detected by client software via the private multicast protocol in the Local Area Network (LAN).
11 Click Save.
A reboot is required for the settings to take effect.
37
Network
9.2
DNS Server
The Preferred DNS Server is the primary domain name server that translates domain names and host names into the corresponding IP addresses. The Alternate DNS Server is a second domain name server that is used if the Preferred DNS Server is unavailable. Configure the
DNS server settings if they are required for specific applications, such as sending email.
To configure the DNS Server settings
1 In Preferred DNS Server and Alternate DNS Server, type the IP addresses of the two
DNS servers.
Click Save.
2
Port numbers
Refer to the following table to change a default port number of the camera.
Port
HTTP Port
RTSP Port
HTTPS Port
Server Port
Default value
80
554
443
8000
Range
Any unoccupied number
1024~65535
Any unoccupied number
2000~65535
1
2
To change a port number
Replace the current port number with a value from the corresponding range in the table above.
Click Save.
A reboot is required for the settings to take effect.
DDNS
Network > DDNS
What this tab is for
If your camera is set to use PPPoE as its default network connection, you can use the DDNS tab to configure the Dynamic DNS (DDNS) for network access.
38
Network
9.3
Note: Registration on the DDNS server is required before you configure the DDNS settings of the camera.
3
4
1
2
To turn on DDNS
Select Enable DDNS.
In the DDNS Type list, select the DDNS type you will be using.
Configure the DDNS settings for the selected type as described below .
Click Save.
A reboot is required for the settings to take effect.
1
4
5
2
3
6
To implement DynDNS
In Server Address, type the server address of DynDNS (for example, members.dyndns.org).
In Domain, type the domain name obtained from the DynDNS website.
In User Name, type the user name registered on the DynDNS website.
In Port, type the port number of the DynDNS server.
In Password, type the password registered on the DynDNS website.
In Confirm, type the same password once more.
To implement IPServer
● In Server Address, type the server address of the IP Server.
To use the IP Server, you have to apply a static IP address, subnet mask, gateway and preferred DNS from the ISP. Under “Server Address” should be entered the static IP address of the computer that runs the IP Server software.
3
4
1
2
5
6
To implement NO-IP
In Server Address, type the server address as www.noip.com.
In Domain, type the domain name you registered.
In User Name, type the user name.
In Port, type the port number, if needed.
In Password, type the password.
In Confirm, type the same password once more.
After clicking Save, you can view the camera with the domain name.
PPPoE
Network > PPPoE
39
Network
9.4
What this tab is for
If you have no router but only a modem, you can use the Point-to-Point Protocol over
Ethernet (PPPoE) function. PPPoE enables users to transfer data securely.
1
2
3
To configure PPPoE
Select Enable PPPoE.
For PPPoE access, type the user name and password (2x).
The user name and password should be assigned by your Internet Service Provider
(ISP).
Click Save.
A reboot is required for the settings to take effect.
SNMP
Network > SNMP
What this tab is for
On the SNMP tab, you can turn on SNMP and configure its settings to get the camera status, parameters and alarm related information and manage the camera remotely when it is connected to the network.
40
Network
9.5
Before you continue
Before you set up SNMP, download and install the SNMP software and configure it to receive the camera information via the SNMP port. By setting the Trap Address, the camera can send the alarm event and exception messages to the surveillance centre.
Note: The SNMP version you select on the SNMP tab should be the same as that of the
SNMP software. The SNMP version that you select must meet the security level you require.
SNMP v1 provides no security. SNMP v2 requires a password for access. SNMP v3 provides encryption and if you use v3, an HTTPS protocol must be enabled.
1
2
3
To turn on SNMP
Select the check box of the required SNMP version.
Configure the SNMP settings.
The settings you configure here should correspond with the settings of the SNMP software.
Click Save.
A reboot is required for the settings to take effect.
802.1X
Network > 802.1X
What this tab is for
The camera supports the IEEE 802.1X standard. IEEE 802.1X is a port-based network access control. It enhances the security level of the LAN. When devices connect to this network with
IEEE 802.1X standard, authentication is needed. If the authentication fails, the devices do not connect to the network. On this tab, you can turn on this feature so that the camera data is secured and user authentication is needed when connecting the camera to the network.
Authentication steps
The authentication server must be configured. Apply for and register a user name and password for 802.1X in the server.
● Before connecting the camera to the protected LAN, request a digital certificate from a
Certificate Authority.
● The camera requests access to the protected LAN via the authenticator (a switch).
● The switch forwards the identity and password to the authentication server (RADIUS server).
● The switch forwards the certificate of authentication server to the camera.
41
Network
9.6
● If all the information is validated, the switch allows network access to the protected network.
3
4
1
2
5
6
7
8
To turn on IEEE 802.1X
Connect the network camera directly to your PC with a network cable.
Log on to the camera.
Go to the 802.1X tab of the Network page.
Select Enable IEEE 802.1X.
In the EAPOL version list, select the version which corresponds with the version of the router or switch.
Type the user name and password (issued by the Certificate authority) (2x) to access the server.
Click Save.
The camera reboots when you save the settings.
After the configuration, connect the camera to the protected network.
QoS
Network > QoS
What this tab is for
On this tab, you can turn on the Quality of Service (QoS) feature which can help solve network delay and network congestion by configuring the priority of data sending.
Differentiated Services Code Point (DSCP)
Differentiated Services (DiffServ, or DS) is a method for adding QoS to IP networks. In routed networks, critical network traffic such as video and audio streams, which require a relatively uninterrupted flow of data, can get blocked due to other traffic. DiffServ can be used to classify network traffic and give precedence - that is, low-latency, guaranteed service, to high-priority traffic.
Each stream has a DSCP (Differentiated Services Code Point) field in the IP header. Routers will identify the network service type in the DSCP field and provide the appropriate level of service.
1
2
To turn on QoS
In Video/Audio DSCP, Event/Alarm DSCP and Management DSCP, type the DSCP value.
The valid range of the DSCP value is 0~63. The higher the DSCP value, the higher the priority.
Click Save.
A reboot is required for the settings to take effect.
42
Network
9.7
Note: Make sure that you enable the QoS function of your network device (such as a router).
NAT
Network > NAT
What this tab is for
On this tab, you can turn on UPnP and configure the Network Address Translation (NAT) settings.
Note: With Universal Plug and Play (UPnP™) enabled, you do not need to configure the port mapping for each port. The camera will be connected to the Wide Area Network via the router.
NAT
To add an extra level of security, NAT can translate the IP addresses of computers on the local network to a single IP address. This address is used by the router that connects the computers to the internet. Should computers on the internet try to connect to computers on the local network, they will only "see" the IP address of the router. The router may include firewall functionality which only allows authorised systems to connect to computers on the local network.
UPnP
UPnP is a networking architecture that provides compatibility among networking equipment, software and other hardware devices. The UPnP protocol allows devices to connect seamlessly and to simplify the implementation of the networks in the home and corporate environments.
1
2
3
To turn on UPnP
Select Enable UPnP™.
In Nickname, type a (user-friendly) name for online detection.
Click Save.
1
2
3
To configure the NAT settings
In the Port Mapping Mode list, select Auto or Manual.
With Manual mode selected, click the table cells you wish to edit and customise the port number values.
Click Save.
43
Network
9.8
HTTPS
Network > HTTPS
What this tab is for
On this tab, you can install security certificates to enable secure connections between the camera and web browsers. If, for example, the HTTPS port number is set to 443 and the IP address is 192.168.1.64, you can establish a secure connection to the camera by typing
“https://192.168.1.64:443” in the address bar of the web browser.
Secure connections
With HTTPS implemented and used on the camera, a safe exchange of data between the camera and a web browser is ensured. Information transported over the network, such as device settings and credentials, is encrypted to protect it against eavesdropping.
Certificates
To implement HTTPS on the camera, you need to install an HTTPS certificate. You can use a self-signed certificate or one created by a Certificate Authority (CA). CA-issued certificates provide a higher level of security and inspire more trust than self-signed certificates. Selfsigned certificates are often installed for test purposes or as a temporary solution until a CAissued certificate has been obtained.
1
2
3
4
5
6
To create a self-signed certificate
To turn on HTTPS, select Enable.
Select Create Self-signed Certificate.
If you already have a certificate installed, the Install Certificate section is hidden. You can display it by deleting the current certificate.
Click Create.
Refer the table below and type the required information in the text boxes.
Click OK.
The certificate information is shown in the HTTPS tab after you successfully created the certificate.
Click Save.
44
Network
Item
Country
Hostname/IP
Validity
Password
State or province
Locality
Organization
Organizational Unit
Description
Two-letter country code (where the certificate is to be used)
Host name or IP address of the device to be certified
Valid period (in days) of the certificate
(Strong) Password
Administrative region in which the organisation is located
City/Location where the organisation is based
Name of the organisation which owns the device
Name of the organisational unit which owns the device
Contact email address
To create an authorised certificate request
1
2
5
6
3
4
7
8
To turn on HTTPS, select Enable.
Select Create the certificate request first ....
If you already have a certificate installed, the Install Certificate section is hidden. You can display it by deleting the current certificate.
Click Create.
Refer the table below and type the required information in the text boxes.
Click OK to save the information.
Click Download.
Save the certificate request.
Send the request to a certificate authority.
Item
Country
Hostname/IP
Password
State or province
Locality
Organization
Organizational Unit
Description
Two-letter country code (where the certificate is to be used)
Host name or IP address of the device to be certified
(Strong) Password
Administrative region in which the organisation is located
City/Location where the organisation is based
Name of the organisation which owns the device
Name of the organisational unit which owns the device
Contact email address
45
Network
9.9
Network > Mail
What this tab is for
The system can be configured to send an email notification to all designated receivers if an alarm event, such as a motion detection, video loss or video tampering event, is detected.
Before you continue
Go to the TCP/IP tab of the Network page and make sure that the IPv4 address, the IPv4 subnet mask, the IPv4 default gateway and the preferred DNS server are set correctly.
To configure the email settings
1
2
3
4
In Sender, type the name of the email sender.
In Sender's Address, type the email address of the sender.
In SMTP Server, type the IP address or host name of the SMTP server (for example, smtp.263xmail.com)
In SMTP Port, type the port number of the SMTP port.
The default TCP/IP port for SMTP is 25 (not secured). The SSL SMTP port is 465.
In the E-mail Encryption list, select SSL, if this is required by the SMTP server.
Select Attached Image, if you want to send emails with attached alarm images.
5
6
7
8
In the Interval list, select the required interval (in seconds).
The interval refers to the time between two actions of sending attached pictures.
If your email server requires authentication, select Authentication.
Users will be prompted for the logon user name and password to log on to the server.
9 In the Receiver table, type the details of up to three receivers who are to be notified of the alarm.
10 Click Save.
46
Network
9.10
FTP
Network > FTP
What this tab is for
On the FTP tab, you can configure the FTP server related information to enable the uploading of captured pictures to the FTP server. Captures can be triggered by events or a timing snapshot task.
1
2
3
4
5
6
7
To configure the FTP server settings
In Server Address, type the IP address of the FTP server.
In Port, type the port number used on the FTP server.
The FTP protocol typically uses port 21 on the FTP server to listen for clients initiating a connection. Port 21 is also where the server is listening for commands issued to it.
In User Name, Password and Confirm, type the authorisation needed to get access to the FTP server.
The target FTP server must hold a user account associated with the camera.
If the FTP server supports anonymous access, you can select Anonymous.
Authorisation details are not required then.
In the Directory Structure list, select the root, parent or child directory.
This sets the folder on the FTP server assigned to the FTP client.
Root: The files are saved to the root folder of the server.
Parent: The files are saved to a folder on the FTP server. To define the folder name, use the Device Name, Device Number, Device IP or a custom name.
Child: The files are saved to a subfolder of the parent directory on the FTP server. To define the folder name, use the Camera Name, Camera Number or a custom name.
To enable the uploading of picture captures to the FTP server, select Upload Picture.
To test your settings. click Test.
Click Save.
1
2
To configure event-triggered snapshots
Select Enable Event-Triggered Snapshot.
In the Quality list, select the picture quality to be used.
47
Network
3
4
5
In Interval, type the interval (in seconds or milliseconds) to be applied between uploads.
In Capture Number, type the number of captures to be uploaded per event.
Range: 1~120.
Click Save.
48
10
10.1
Video
On the Video page, you can configure the settings for video streaming, picture adjustment, text overlays, privacy masks and the region of interest (ROI).
In This Chapter
Streaming
Video > Streaming
What this tab is for
On the Streaming tab, you can select a stream type and configure the associated video streaming settings.
1
2
3
4
To configure video streaming
Select Enable Dual-VCA if you want information of objects (for example, human, vehicle, etc.) highlighted in the video stream.
In the Stream Type list, select Main Stream, or Sub stream.
The main stream is usually for recording and live viewing with good bandwidth, whereas the substream can be used for live viewing when the bandwidth is limited.
In the Resolution list, select the required resolution for the video output.
In the Bitrate Type list, select Variable or Constant.
49
Video
5
6
7
8
Constant bit rate mode (CBR) is generally safest. Although the image quality may vary, the network load generated will remain fairly constant.
If constant picture quality is required and a varying network load will pose no problems, choose Variable bit rate mode (VBR). Video streaming is generally smoother under VBR.
In the Video Quality list, select a video quality level.
The Video Quality list is available if the bit rate type is set to Variable.
Note that higher video quality levels require more bandwidth.
In the Frame Rate list, select a frame rate for the stream.
The frame rate determines the frequency at which the video stream is updated. It is expressed in frames per second (fps). A higher frame rate is advantageous when there is movement in the video stream, as it maintains the image quality throughout.
In the Max. Bitrate list, enter a value for the maximum bit rate to be allowed.
Higher values will give a higher video quality, but more bandwidth is required.
Note that the available values in this list can vary per camera model.
In the Video Encoding list, select the encoding mode - that is, the method used to compress the video input signal.
9
If the Stream Type is set to Main Stream, H.264 is selectable. If the Stream Type is set to Sub Stream, H.264 and MJPEG are selectable.
In I Frame Interval, type the required value.
Range: 1~250. This setting determines the distance in frames between two I-frames.
10 In the SVC list, select ON, Auto or OFF.
Scalable Video Coding (SVC) is an extension of the H.264/AVC standard.
ON: Turns on the SVC function.
OFF: Turns off the SVC function.
Auto: The camera automatically extracts frames from the original video if the network bandwidth is insufficient.
11 Drag the Smoothing slider (available if Bit rate Type is set to Constant) to control the smoothness of the stream.
The higher the smoothing value, the better the fluency of the stream will be. The video quality may not be satisfactory, though.
The lower the smoothing value, the higher the quality of the stream will be. It may not appear as fluent, though.
12 Click Save.
50
Video
10.2
Picture adjustment
Video > Picture Adjustment
What this tab is for
On this tab, you can set the image quality of the camera, including brightness, contrast, saturation, hue, sharpness, etc. You can double-click the live view to enter fullscreen mode.
Double-click again to exit.
Note: The display parameters vary per camera model. Refer to the actual interface for details.
Day/Night switching
To guarantee the image quality in different illuminations, the camera provides two sets of parameters for the user to configure.
● Day/Night Auto-Switch settings
● Day/Night Scheduled Switch settings
Day/Night Auto-Switch settings
The settings described in the following paragraphs are available if you select Auto-Switch.
Image Adjustment
Use the Image Adjustment sliders to adjust the image quality. Range: 1~100. Default value:
50.
● Brightness: Controls the brightness level of the image.
● Contrast: Controls the contrast level of the image - that is, the difference in brightness between the light and dark areas of an image.
● Saturation: Controls the intensity (purity) of the colours in the image.
● Sharpness: Controls the clarity of detail perceived in an image.
51
Video
Exposure Settings
The exposure time refers to the electronic shutter time, which ranges from 1/3 ~ 1/100,000 s. Adjust it according to the actual luminance condition.
Day/Night Switch
Use this section to select the Day/Night switch mode and to configure the smart IR settings.
● Day: The camera stays in day mode.
● Night: The camera stays in night mode.
● Auto: The camera switches automatically between day mode and night mode according to the illumination. The sensitivity ranges from 0~7. The higher the value, the easier the mode switches. The filtering time refers to the interval time between the day/night switch.
You can set it from 5 s to 120 s.
● Schedule: Set the start time and the end time to define the duration for day/night mode.
● Smart Supplement Light: On cameras with IR LEDs, the Smart Supplement Light function gives users an option to adjust the power of the IR LED to provide a clear image that is not overexposed or too dark. Select ON to enable the smart IR.
Backlight Settings
If you focus on an object against strong backlight, the object will be too dark to be seen clearly. Backlight Compensation (BLC) compensates the light to the object in the front to make it clear.
● BLC Area: Select an area from the list. With OFF selected, the WDR setting is available.
● WDR: The wide dynamic range (WDR) function helps the camera provide clear images when there are both very bright and very dark areas simultaneously in the field of view.
WDR balances the brightness level of the whole image to provide clear images with details.
Use the slider to set the WDR level.
White Balance
The White Balance is the white rendition function of the camera used to adjust the colour temperature according to the environment.
Image Enhancement
Digital Noise Reduction (DNR) reduces the noise in the video stream. Normal and OFF are selectable. Set the DNR level from 0~100. The default value is 50.
Video Adjustment
This section offers the following functionality:
● Mirror: Mirrors the image so you can see it inversed. Options: Left/Right, Up/Down,
Center, and OFF.
● Rotate: To make a complete use of the 16:9 aspect ratio, you can turn on the Rotate function when you use the camera in a narrow view scene. When installing the camera, turn it to 90 degrees or rotate the 3-axis lens to 90 degrees and set the Rotate Mode to
ON. You will get a normal view of the scene with a 9:16 aspect ratio to ignore the needless information such as the wall and get more meaningful information of the scene.
● Video Standard: Options: PAL(50HZ) and NTSC(60HZ). Select the applicable video standard according to the video system in your country.
● Capture Mode: Is the selectable video input mode to meet the different demands of the field of view and the resolution.
Other
Some of the camera models support the CVBS output.
52
Video
10.3
Day/Night Scheduled-Switch
The Day/Night scheduled-switch configuration interface enables you to set separate camera parameters for day and night to guarantee the image quality in different illuminations.
1
2
3
6
7
4
5
To configure the Scheduled-Switch settings
In Start Time and End Time, enter the start and end time of the switch.
Click Common.
Configure the common settings applicable to the day mode and the night mode.
For information about each setting, see the description of the Day/Night Auto-Switch mode.
Click Day.
Configure the settings applicable to the day mode.
Click Night.
Configure the settings applicable to the night mode.
The settings are saved automatically as you make changes.
Text overlay
Video > Text Overlay
What this tab is for
On the Text Overlay tab, you can add and edit information for On-Screen Display (OSD).
OSD Items
The camera name, date and time information and custom text overlays can be superimposed onto the video images.
1
To add the camera name and date/time information
Select Display Name, Display Date and Display Week as needed.
53
Video
10.4
2
3
4
5
In Camera Name, type the camera name.
In the Time Format, Date Format, Display Mode, OSD Size and Font Color lists, select the required formatting.
In the Live View window, drag the OSD frame to position it as needed.
Click Save.
3
4
1
2
To add a text overlay
Select the overlay you wish to add.
In the overlay text box, type the text to be displayed.
In the Live View window, drag the OSD frame to position it as needed.
Click Save.
Privacy mask
Video > Privacy Mask
What this tab is for
On the Privacy Mask tab, you can superimpose privacy masks onto the video images. This makes it possible to cover certain areas on the live video to prevent certain spots in the surveillance area from being live viewed and recorded.
1
2
3
To add a privacy mask
Select Enable Privacy Masks.
Click Draw Area.
Drag your mouse pointer across the Live View window to draw the mask area.
You can drag the sizing handles to resize the area. If necessary, drag the area to position it correctly.
54
Video
10.5
4
5
6
7
Click Stop Drawing.
- or -
Click Clear All to remove all of the areas you set without saving them.
Click Add.
The privacy mask is saved and added to the Privacy Mask List.
(Optional) In the Name box, type a name for the mask.
Click Save.
1
2
To delete a privacy mask
In the Privacy Mask List, select the mask.
Click Delete.
ROI
Video > ROI
55
Video
What this tab is for
On the ROI tab, you can draw a Region of Interest (ROI). ROI encoding helps to discriminate the ROI and background information in video compression, which means, the technology assigns more encoding resources to the region of interest. This increases the quality of the
ROI, whereas the background information is less focused. Note that the ROI function varies per camera model.
To configure a fixed region for ROI
7
8
5
6
3
4
1
2
In the Stream Type list, select the stream for ROI encoding.
In the Region No. list, select a region number.
Under Fixed Region, select Enable.
Click Draw Area.
Drag your mouse pointer across the Live View window to draw the region.
(Optional) Drag the region to position it correctly.
Click Stop Drawing.
In the ROI Level list, select the image quality level.
9
The higher the value, the better the image quality.
In Region Name, type a name for the region.
10 Click Save.
1
2
3
To remove a fixed region
In the Region No. list, select the region.
Click Clear.
To confirm, click OK.
56
11
11.1
Events
This section explains how to configure the network camera to respond to events, such as motion detection, video tampering, exception, intrusion detection and line crossing detection.
These events can trigger the linkage methods, such as Notify Surveillance Center, Send Email,
Upload to FTP, Trigger Alarm Output, and Trigger Channel.
In This Chapter
Motion Detection
Events > Motion Detection
What this tab is for
Motion Detection detects moving objects in the configured surveillance area. A series of actions can be taken when an alarm is triggered. On the Motion Detection tab, you can turn on Motion Detection and configure the settings of this function.
57
Events
Modes
To detect moving objects accurately and reduce the false alarm rate, the following configuration modes are available for different motion detection environments:
● Normal configuration
● Expert configuration
Normal mode
1
2
The Normal configuration mode adopts the same set of motion detection parameters in the daytime and at night. It involves the following steps:
3
On the Area Settings tab, you define the area to be monitored.
On the Arming Schedule tab, you define when you want the function to be active.
On the Linkage Method tab, you define the action(s) to be taken when an event occurs.
1
2
5
6
3
4
7
8
To set the motion detection area
Select Enable Motion Detection.
If you want to have detected objects marked by green rectangles, select Enable
Dynamic Analysis for Motion.
Note: If you do not want the detected objected marked by the rectangles, go to System
> Local Configuration > Live View Parameters > Rules, and then select Disable.
On the Area Settings tab, click Draw Area.
Drag your mouse pointer across the Live View window to draw a detection area.
Click Stop Drawing to finish the drawing of one area.
(Optional) Click Clear All to delete all areas.
(Optional) Drag the slider to set the sensitivity of the detection.
The higher the value, the more easily the alarm will be triggered.
Click Save.
1
2
To set the arming schedule
On the Arming Schedule tab, drag your mouse pointer across the required day(s) to set the arming schedule.
A Copy button appears as you move your pointer across the schedule. You can click it to copy the settings of a specific day to another day.
You can click a time section to edit, save or delete it.
Click Save.
To set the alarm actions
1
2
On the Linkage Method tab, select the required actions (see descriptions below).
Options: Send Email, Notify Surveillance Center, Upload to FTP, Trigger Channel.
Click Save.
Send Email
Send an email with alarm information to a user or users when an event occurs. Before emails can be sent, the related settings on the Mail tab of the Network page must be correctly and completely configured.
Notify Surveillance Center
Send an exception or alarm signal to remote management software when an event occurs.
58
Events
Upload to FTP
Capture the image when an alarm is triggered and upload the picture to an FTP server. Before images can be uploaded, the related settings on the FTP tab of the Network page and on the
Capture tab of the Storage page must be correctly and completely configured. The captured image can also be uploaded to the available SD card or network disk.
Trigger Channel
Video is recorded when an event occurs. Before recording can start, the recording schedule on the Record Schedule tab of the Storage page must be set.
Expert mode
Expert mode is mainly used to configure the sensitivity and proportion of the object in relation to the area, per available Day/Night Settings switch.
1
2
3
4
5
6
To configure settings in Expert mode
Select the Switch Day and Night Setting.
OFF: disables the day and night switch.
Auto-Switch: automatically switches the day and night mode according to the illumination.
Scheduled-Switch: enables you to set a start and end time.
In the Area list, select the area number.
Draw the detection area as described for the normal configuration mode.
Up to eight areas are supported.
Drag the Sensitivity and Percentage sliders to adjust the sensitivity and proportion of the object in relation to the area.
Sensitivity: The higher the value, the more easily the alarm will be triggered.
Percentage: When the size proportion of the moving object exceeds the predefined value, the alarm is triggered. The lower the value, the more easily the alarm will be triggered.
Set the arming schedule and linkage method as in the normal configuration mode.
Click Save.
59
Events
11.2
Video Tampering
Events > Video Tampering
What this tab is for
On the Video Tampering tab, you can configure the camera to raise an alarm when the lens is covered and to link specific response actions to such an event.
Steps
Video Tampering configuration involves the following steps:
1 On the Area Settings tab, you enable the function and set the sensitivity.
2
3
On the Arming Schedule tab, you define the period(s) when you want the function to be active.
On the Linkage Method tab, you define the action(s) to be taken when an event occurs.
1
2
3
To configure video tampering detection
Select Enable.
On the Area Settings tab, drag the slider to set the sensitivity of the detection.
Click Save.
1
2
To set the arming schedule
On the Arming Schedule tab, drag your mouse pointer across the required day(s) to set the arming schedule.
A Copy button appears as you move your pointer across the schedule. You can click it to copy the settings of a specific day to another day.
You can click a time section to edit, save or delete it.
Click Save.
1
2
To set the alarm actions
On the Linkage Method tab, select the required actions (see descriptions below).
Options: Send Email, Notify Surveillance Center.
Click Save.
60
Events
11.3
Send Email
Send an email with alarm information to a user or users when an event occurs. Before emails can be sent, the related settings on the Mail tab of the Network page must be correctly and completely configured.
Notify Surveillance Center
Send an exception or alarm signal to remote management software when an event occurs.
Exception
Events > Exception
What this tab is for
On the Exception tab, you can link actions to the occurrence of an Exception Alarm. The exception type can be HDD Full, HDD Error, Network Disconnected, IP address Conflicted and
Illegal Login to the camera.
To set the actions for exception alarms
1
2
3
4
In the Exception Type list, select the exception you need to configure.
Select the required actions (see descriptions below).
Options: Send Email, Notify Surveillance Center.
Click Save.
Repeat steps 1-3 for other exception types you need to configure.
Send Email
Send an email with alarm information to a user or users when an event occurs. Before emails can be sent, the related settings on the Mail tab of the Network page must be correctly and completely configured.
Notify Surveillance Center
Send an exception or alarm signal to remote management software when an event occurs.
61
Events
11.4
Intrusion Detection
Events > Intrusion Detection
What this tab is for
The Intrusion detection function detects people, vehicles or other objects which enter and loiter in a predefined virtual region longer than the set duration. On the Intrusion Detection tab, you can enable and set up the function, and define the actions to be taken when the alarm is triggered.
Steps
Intrusion Detection configuration involves the following steps:
1 On the Area Settings tab, you define the area to be monitored.
2
3
On the Arming Schedule tab, you define the period(s) when you want the function to be active.
On the Linkage Method tab, you define the action(s) to be taken when an event occurs.
To set the intrusion detection area(s)
3
4
1
2
5
Select Enable.
On the Area Settings tab, click to open the Region list.
Select the region you want to create.
Click Draw Area.
Left-click in the Live Video window to set the first of the four vertexes of the detection area.
8
9
6
7
Move the mouse pointer to the next vertex.
Left-click to set the second vertex.
In the same way, set vertexes three and four.
Right-click to complete your drawing.
10 Click Stop Drawing.
62
Events
11 Drag the Threshold(s) slider to set the time threshold.
Range: [0 s ~ 10 s]. This is the threshold for the duration of the object loitering in the region. If you set the value to 0, the alarm is triggered immediately after the object has entered the region.
12 Drag the Sensitivity slider to set the sensitivity of the detection.
Range: [1~100]. The value of the sensitivity defines the size of the object which can trigger the alarm. If the sensitivity is high, a very small object can trigger the alarm.
13 Drag the Percentage slider to set the ratio of the in-region part of the object which can trigger the alarm.
For example, if the percentage is set as 50%, when the object enters the region and occupies half of the whole region, the alarm is triggered.
14 Repeat steps 3-13 to configure other regions.
Up to 4 regions can be set. You can click Clear to delete all existing regions.
15 Click Save.
1
2
To set the arming schedule
On the Arming Schedule tab, drag your mouse pointer across the required day(s) to set the arming schedule.
A Copy button appears as you move your pointer across the schedule. You can click it to copy the settings of a specific day to another day.
You can click a time section to edit, save or delete it.
Click Save.
To set the alarm actions
1
2
On the Linkage Method tab, select the required actions (see descriptions below).
Options: Send Email, Notify Surveillance Center, Upload to FTP, Trigger Channel.
Click Save.
Send Email
Send an email with alarm information to a user or users when an event occurs. Before emails can be sent, the related settings on the Mail tab of the Network page must be correctly and completely configured.
Notify Surveillance Center
Send an exception or alarm signal to remote management software when an event occurs.
Upload to FTP
Capture the image when an alarm is triggered and upload the picture to an FTP server. Before images can be uploaded, the related settings on the FTP tab of the Network page and on the
Capture tab of the Storage page must be correctly and completely configured. The captured image can also be uploaded to the available SD card or network disk.
Trigger Channel
Video is recorded when an event occurs. Before recording can start, the recording schedule on the Record Schedule tab of the Storage page must be set.
63
Events
11.5
Line Crossing Detection
Events > Line Crossing Detection
What this tab is for
The Line Crossing Detection function detects people, vehicles or other objects which cross a predefined virtual line. On the Line Crossing Detection tab, you can enable and set up the function, and define the actions to be taken when the alarm is triggered. Note that this function varies per camera model.
Steps
Line Crossing Detection configuration involves the following steps:
1 On the Area Settings tab, you draw and configure the virtual line to be monitored.
2
3
On the Arming Schedule tab, you define the period(s) when you want the function to be active.
On the Linkage Method tab, you define the action(s) to be taken when an event occurs.
3
4
1
2
5
6
7
To draw the virtual line(s)
Select Enable.
On the Area Settings tab, click to open the Line list.
Select the line you want to create.
Click Draw Area.
A virtual line is displayed in the centre of the Live View window.
Drag the line to move it to the required position.
Drag the sizing handles to resize the line.
In the Direction list, select a direction for the line crossing detection.
A<->B: Objects crossing the line from A to B, and objects crossing from B to A can be detected.
A->B: Objects crossing from A to B can be detected.
B->A: Objects crossing from B to A can be detected.
64
Events
8 Drag the Sensitivity slider to set the sensitivity of the detection.
Range: [1-100]. The higher the value, the more easily the line crossing action can be detected.
9 Repeat the steps above to configure other lines.
Up to 4 lines can be set. You can click Clear to delete all existing lines.
10 Click Save.
1
2
To set the arming schedule
On the Arming Schedule tab, drag your mouse pointer across the required day(s) to set the arming schedule.
A Copy button appears as you move your pointer across the schedule. You can click it to copy the settings of a specific day to another day.
You can click a time section to edit, save or delete it.
Click Save.
To set the alarm actions
1
2
On the Linkage Method tab, select the required actions (see descriptions below).
Options: Send Email, Notify Surveillance Center, Upload to FTP, Trigger Channel.
Click Save.
Send Email
Send an email with alarm information to a user or users when an event occurs. Before emails can be sent, the related settings on the Mail tab of the Network page must be correctly and completely configured.
Notify Surveillance Center
Send an exception or alarm signal to remote management software when an event occurs.
Upload to FTP
Capture the image when an alarm is triggered and upload the picture to an FTP server. Before images can be uploaded, the related settings on the FTP tab of the Network page and on the
Capture tab of the Storage page must be correctly and completely configured. The captured image can also be uploaded to the available SD card or network disk.
Trigger Channel
Video is recorded when an event occurs. Before recording can start, the recording schedule on the Record Schedule tab of the Storage page must be set.
65
12
12.1
Storage
Before you configure recording and storage settings, make sure that a network storage device is available within the network or that an SD card is inserted in your camera.
In This Chapter
HDD Management
Storage > HDD Management
What this tab is for
On the HDD Management tab, you can perform the following tasks:
● Initialise a network disk or an SD card that you have inserted into the camera.
● Define the quota for recordings and snapshots.
66
Storage
12.2
Available storage
Network disks added via the Net HDD tab or an SD card inserted into the camera will be available in the HDD Management table. You can see the capacity, free space, status type and property of each item. Up to eight NAS disks can be connected to the camera. If the status is
Uninitialised you need to format the disk or card before you can use it.
1
2
To initialise a network disk or SD card
In the HDD Management table, click the check box to select the disk or card.
Click Format.
Note that all existing data (if any) on the storage medium will be erased and irretrievably lost!
When the formatting has completed, the status of disk changes to “Normal”.
1
2
To define the quota for recordings and snapshots
In Percentage of Picture and Percentage of Record, type the quota percentages you want to assign.
To activate the settings, click Save and refresh the browser page.
Record Schedule
Storage > Record Schedule
What this tab is for
There are two kinds of recording for the camera:
● Manual Recording
● Scheduled Recording
This section gives instructions for configuring scheduled recording. For instructions on manual recording, see the description of the Live View page.
67
Storage
Storage medium
By default, the files of recordings and snapshots are stored on the SD card (if supported) or on a network disk. Network disks can be added via the Net HDD tab. On the HDD
Management tab, you can initialise connected disks and the SD card.
To set up scheduled recording
1
2
3
4
5
Select Enable.
Under Enable, click to open the Recording type list.
Select a recording type.
Available options: Continuous, Motion, Events.
See below for a description of each type.
Drag your mouse pointer across the required day(s) to set up the recording schedule for this type of recording.
Repeat steps 3 and 4 for other recording types, if necessary.
A Copy button appears as you move your pointer across the schedule. You can click it to copy the settings of a specific day to another day.
You can click a time section to edit, save or delete it.
Click Advanced.
6
7
8
Select or clear Overwrite, as needed.
If you enable this function and the HDD is full, the new record files overwrite the oldest record files automatically.
In the Pre-record list, select a time span.
The recording is started at the number of seconds set here, before the scheduled time or the event. For example, if an alarm triggers the recording at 10:00, and the pre-record time is set as 5 seconds, the camera starts recording at 9:59:55.
In the Post-record list, select a time span.
9
The recording is stopped at the time set here, after the scheduled time or the event. For example, if an alarm triggered recording ends at 11:00, and the post-record time is set as 5 seconds, the camera records until 11:00:05.
10 Click OK.
11 Click Save.
Continuous recording
Video is recorded automatically according to the time of the schedule.
Recording triggered by Motion Detection
Video is recorded when motion is detected. Besides configuring the recording schedule, you have to set the motion detection area and select the Trigger Channel check box in the Linkage
Method of the Motion Detection settings interface. For more information, see the description of the Motion Detection tab (Event page).
Recording triggered by Event
Video is recorded on the occurrence of so-called smart events such as Intrusion Detection, and others found on the Events page. Besides configuring the recording schedule, make sure that the settings of the specific event are correctly configured. For more information, see the description of the Event page.
68
Storage
12.3
Capture
Storage > Capture
What this tab is for
On the Capture tab, you can configure the settings for snapshot captures.
Storage medium
By default, the files of recordings and snapshots are stored on the SD card (if supported) or on a network disk. Network disks can be added via the Net HDD tab. On the HDD
Management tab, you can initialise connected disks and the SD card.
1
2
To set up the capture schedule
On the Capture Schedule tab, drag your mouse pointer across the required day(s) to set up the recording schedule for this type of recording.
A Copy button appears as you move your pointer across the schedule. You can click it to copy the settings of a specific day to another day.
You can click a time section to edit, save or delete it.
Click Save.
1
2
3
4
5
To enable timing snapshots
On the Capture Parameters tab, select Enable Timing Snapshot.
In the Quality list, select the required quality.
In the Interval unit list, select a unit.
Options: millisecond, s, min, Hour, Day(s).
Type a value in Interval.
This sets the time interval between two snapshots.
Click Save.
3
4
1
2
To upload continuous snapshots to an FTP server
Go to the FTP tab of the Network page.
Configure the FTP settings.
Select Upload Picture.
Click Save.
69
Storage
12.4
Net HDD
Storage > Net HDD
What this tab is for
On the Net HDD tab, you can configure and test the settings for Network Attached Storage
(NAS).
Before you continue
The network disk should be available within the network and properly configured to store the recorded files, log files, etc.
To add a network disk
1
2
3
6
7
4
5
In the Net HDD table, click to select a HDD No.
In the Server Address column, type the IP address of the server which houses the network disk.
In the File Path column, type the path to the server.
For information about the file path, contact your system administrator or refer to the user manual of your NAS.
In the Mounting Type list, select NFS or SMB/CIFS.
If you selected NFS, type the user name and password.
To test your settings, click Test.
Click Save.
Note: You can initialise the network disk on the HDD Management tab of the Storage page.
Use strong passwords
For your privacy and to better protect your system against security risks, we strongly advise the use of strong passwords for all functions and network devices. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user of the camera.
To create a strong password
● Use at least eight characters
● Do not include your real name, user name, company name, or other personal information
70
Storage
● Do not use complete words that can be found in a dictionary
● Use a random combination of at least two of the following categories: upper case letters, lower case letters, numbers and special characters
Number of network disks
You can connect up to eight network disks to the camera.
1
2
To delete a network disk
In Delete column of the Net HDD table, click the red Delete icon.
Click Save.
71
Index
8
802.1X..................................................41
A
About this manual.................................... 5
Authentication........................................33
B
Basic information....................................24
C
Capture.................................................69
Compliance information.............................8
Connect the camera to a LAN................... 10
Connect the camera to a WAN.................. 11
Connect to network.................................. 9
D
DDNS....................................................38
E
Events.................................................. 57
Exception.............................................. 61
F
FTP.......................................................47
G
Get access to the camera.........................14
Get access via Siqura Device Manager....... 15
Get access via UPnP................................16
Get access via web browser..................... 14
H
HDD Management...................................66
HTTPS...................................................44
I
Install the videoplayer plug-in.................. 18
Intrusion Detection................................. 62
IP Address Filter..................................... 34
L
Line Crossing Detection........................... 64
Live View...............................................19
Local configuration..................................30
Log.......................................................29
Log on to the camera.............................. 17
M
Mail...................................................... 46
Motion Detection.................................... 57
N
NAT...................................................... 43
Net HDD................................................70
Network................................................ 36
P
Picture adjustment..................................51
Playback................................................22
PPPoE................................................... 39
Privacy mask......................................... 54
Q
QoS...................................................... 42
R
Record Schedule.....................................67
ROI...................................................... 55
S
Safety and compliance.............................. 6
Safety instructions....................................6
Security................................................ 32
SNMP....................................................40
Storage................................................. 66
Streaming............................................. 49
System................................................. 24
System requirements................................9
T
TCP/IP.................................................. 36
Text overlay...........................................53
Time settings......................................... 25
U
Upgrade and maintenance....................... 27
User Management...................................32
V
Video.................................................... 49
Video Tampering.................................... 60
72
Advertisement
Key features
- High-resolution video capture
- Advanced video analysis features
- Reliable network connectivity
- User-friendly web interface
- Remote management capabilities
- Motion detection
- Video tampering detection
- Line crossing detection
