Wolf | 801640 | User's Manual | Wolf 801640 User's Manual

Wolf 801640 User's Manual
MODEL 801640
Page 1
EXTERIOR VENTILATOR KITS
!
WARNING
CAUTION
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer or your distributor.
2. Before servicing or cleaning unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
3.Installation work and electrical wiring must be done by a
qualified person(s) in accordance with all applicable codes
and standards, including fire-rated construction codes and
standards.
4. Sufficient air is needed for proper combustion and exhausting
of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment
manufacturer’s guidelines and safety standards such as those
published by the National Fire Protection Association (NFPA),
and the American Society for Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE), and the local code authorities.
5.When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. Do not use this unit with an additional speed control device.
8. To reduce the risk of fire, use only steel ductwork.
9. This unit must be grounded.
TO REDUCE THE RISK OF A COOKTOP GREASE FIRE:
1. Never leave surface units unattended at high settings. Boilovers
cause smoking and greasy spillovers that may ignite. Heat oils
slowly on low or medium settings.
2.Always turn hood ON when cooking at high heat or when
cooking flaming foods.
3. Clean ventilating fans frequently. Grease should not be allowed
to accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate for the
size of the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE
EVENT OF A COOKTOP GREASE FIRE, OBSERVE THE
FOLLOWING:*
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or
metal tray, then turn off the burner. BE CAREFUL TO PREVENT
BURNS. If the flames do not go out immediately, EVACUATE
AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN - You may be burned.
3.DO NOT USE WATER, including wet dishcloths or towels violent steam explosion will result.
4. Use an extinguisher ONLY if:
A.You know you have a Class ABC extinguisher and you
already know how to operate it.
B. The fire is small and contained in the area where it started.
C.The fire department is being called.
D. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips” published by NFPA.
1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
2. To avoid motor bearing damage and noisy and/or unbalanced
impellers, keep drywall spray, construction dust, etc. off power
unit.
3. Your ventilator motor has a thermal overload which will automatically shut off the motor if it becomes overheated. The motor
will restart when it cools down. If the motor continues to shut
off and restart, have the hood serviced.
4. Please read specification label on product for further information and requirements.
SPECIFICATIONS
MODEL VOLTS
801640
120
AMPS
2.4
CFM
600
DUCT SIZE
10 "DIA.
PLAN THE INSTALLATION
1. Locate the ventilator so the length of the duct run and number
of elbows and transitions needed are kept to a minimum.
2. Where possible, ventilator should be located between wall
studs or roof rafters.
3. Avoid pipes, wires, or other ductwork that may be running
through the wall.
4. Be sure that there is enough space for any transitions that
may be needed between the ventilator and the connecting
ductwork.
5. For best performance, locate transitions nearest to ventilator.
MODEL 801640
ROOF MOUNT
Page 2
INSTALLATION
For use with Models CTWH30, CTWH36, IH4227,W302418-W422418,W302718-W422418,W362210-W482210.
WIRE THE VENTILATOR
PREPARE THE ROOF
BLACK
TO
BLACK
20¾"
8½"
Rafter
Rafter
Pilot
Hole
Roof
Roof
10 3 /8 "
REMOVE
SHINGLES
1¼"
dia. hole
11"
dia.
hole
120 VAC
LINE IN
20½"
Remove BIRD SCREEN and WIRING COVER.
6 Feed the electric power cable through the 1¼" DIAMETER
HOLE and connect cable to ventilator with a proper
connector for the type of cable being used.
7 Connect BLACK TO BLACK, WHITE TO WHITE, and the
GREEN TO GREEN or bare wire. Replace wiring cover.
INSTALL THE VENTILATOR
OUTSIDE - ROOF VIEW
From inside the attic space:
1 Drill a PILOT HOLE up through the roof, 8½" from the inside
edge of a ROOF RAFTER.
Shipping
Cardboard
Remove
roofing
nails from
top 2/3 of
shingles.
Wiring
Cover
2"
Bird Screen
6¾
2"
6
Mounting
Holes
7 Cover
Screws
From outside - on the roof:
2 Measure and mark the 20¾" x 20½" rectangle. Cut and
remove only the shingles inside this rectangle.
3 Measure and mark the 11" DIAMETER HOLE and the 1¼"
DIAMETER HOLE. Cut these holes all the way through the
roof.
"
GREEN
TO
GREEN
5Remove 7 COVER SCREWS and lift off ventilator cover.
9 1 /8 "
7¼"
24¾
WHITE
TO
WHITE
Flashing Sheet
"
"
28¼
OUTSIDE - ROOF VIEW
8Remove SHIPPING CARDBOARD from blower wheel.
9 Remove roofing nails from top 2/3 of shingles around cut-out
area.
For flat roof installations:
4 Build a curb that will mount the blower at a minimum pitch of
2/12. Discharge end of the blower should be pointed away
from prevailing winds.
10 Slide the ventilator's FLASHING SHEET up and under
the loosened shingles until ventilator's discharge collar
fits into 11" diameter hole.
11 Use the 6 screws (provided) to attach the ventilator to the
roof. 6 MOUNTING HOLES are provided.
12 Seal the screw heads, loosened shingles, and edges of
the flashing sheet, with a good grade of roofing cement.
13 Check for free movement of the spring-loaded damper,
re-install BIRD SCREEN and ventilator cover. Turn on
power and check operation.
MODEL 801640
WALL MOUNT
Page 3
INSTALLATION
For use with Models CTWH30, CTWH36, IH4227,W302418-W422418,W302718-W422418,W362210-W482210.
WIRE THE VENTILATOR
PREPARE THE WALL
BLACK
TO
BLACK
24¾"
10¾"
REMOVE
SIDING
11" dia.
hole
Pilot
Hole
120 VAC
LINE IN
Wall Stud
12 7 /8 "
Wall Stud
8½"
1¼"
dia. hole
28¼"
9 1 /8 "
7¼"
WHITE
TO
WHITE
GREEN
TO
GREEN
4Remove 7 COVER SCREWS and lift off ventilator cover.
Remove BIRD SCREEN and WIRING COVER.
5 Feed the electric power cable through the 1¼" DIAMETER
HOLE and connect cable to ventilator with a proper
connector for the type of cable being used.
6 Connect BLACK TO BLACK, WHITE TO WHITE, and the
GREEN TO GREEN or bare wire. Replace wiring cover.
INSTALL THE VENTILATOR
OUTSIDE - WALL VIEW
From inside the wall:
1 Drill a PILOT HOLE through the wall, 8½" from the inside
edge of a WALL STUD.
6
Mounting
Holes
7 Cover
Screws
From outside - on the wall:
2 Measure and mark the 25" x 29½" rectangle. Cut and remove
only the siding inside this rectangle.
3 Measure and mark the 11" DIAMETER HOLE and the 1¼"
DIAMETER HOLE. Cut these holes all the way through the
wall.
Shipping
Cardboard
Wiring
Cover
Bird Screen
Flashing Sheet
OUTSIDE - WALL VIEW
7Remove SHIPPING CARDBOARD from blower wheel.
8 Place ventilator on wall so that ventilator's discharge collar
fits into 11" diameter hole.
9 Use the 6 screws (provided) to attach the ventilator to the
wall. 6 MOUNTING HOLES are provided.
Seal the screw heads and edges of the flashing sheet with
a good grade of roofing cement.
11 Check for free movement of the spring-loaded damper,
re-install BIRD SCREEN and ventilator cover. Turn on
power and check operation.
10
MODEL 801640
Page 4
ATTACH POWER CORD TO HOOD
Some wall and island hoods (excluding CTWH30, CTWH36, IH4227) require the use of a separate
power cord and strain relief bushing (included), for proper wiring of exterior blowers. Please refer to
the installation instructions supplied with your Wolf hood.
MODEL 801641
Page 1
EXTERIOR VENTILATOR KITS
!
WARNING
CAUTION
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer or your distributor.
2. Before servicing or cleaning unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
3.Installation work and electrical wiring must be done by a
qualified person(s) in accordance with all applicable codes
and standards, including fire-rated construction codes and
standards.
4. Sufficient air is needed for proper combustion and exhausting
of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment
manufacturer’s guidelines and safety standards such as those
published by the National Fire Protection Association (NFPA),
and the American Society for Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE), and the local code authorities.
5.When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. Do not use this unit with an additional speed control device.
8. To reduce the risk of fire, use only steel ductwork.
9. This unit must be grounded.
TO REDUCE THE RISK OF A COOKTOP GREASE FIRE:
1. Never leave surface units unattended at high settings. Boilovers
cause smoking and greasy spillovers that may ignite. Heat oils
slowly on low or medium settings.
2.Always turn hood ON when cooking at high heat or when
cooking flaming foods.
3. Clean ventilating fans frequently. Grease should not be allowed
to accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate for the
size of the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE
EVENT OF A COOKTOP GREASE FIRE, OBSERVE THE
FOLLOWING:*
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or
metal tray, then turn off the burner. BE CAREFUL TO PREVENT
BURNS. If the flames do not go out immediately, EVACUATE
AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN - You may be burned.
3.DO NOT USE WATER, including wet dishcloths or towels violent steam explosion will result.
4. Use an extinguisher ONLY if:
A.You know you have a Class ABC extinguisher and you
already know how to operate it.
B. The fire is small and contained in the area where it started.
C.The fire department is being called.
D. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips” published by NFPA.
1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
2. To avoid motor bearing damage and noisy and/or unbalanced
impellers, keep drywall spray, construction dust, etc. off power
unit.
3. Your ventilator motor has a thermal overload which will automatically shut off the motor if it becomes overheated. The motor
will restart when it cools down. If the motor continues to shut
off and restart, have the hood serviced.
4. Please read specification label on product for further information and requirements.
SPECIFICATIONS
MODEL VOLTS
801641
120
AMPS
5.7
CFM
900
DUCT SIZE
10 "DIA.
PLAN THE INSTALLATION
1. Locate the ventilator so the length of the duct run and number
of elbows and transitions needed are kept to a minimum.
2. Where possible, ventilator should be located between wall
studs or roof rafters.
3. Avoid pipes, wires, or other ductwork that may be running
through the wall.
4. Be sure that there is enough space for any transitions that
may be needed between the ventilator and the connecting
ductwork.
5. For best performance, locate transitions nearest to ventilator.
MODEL 801641
ROOF MOUNT
Page 2
INSTALLATION
For use with Models CTWH30, CTWH36, IH4227, DD30R, DD36R, DD45R, W30-662418,
W30-662718, W36-482210, I36-663418, L34-582212.
WIRE THE VENTILATOR
PREPARE THE ROOF
BLACK
TO
BLACK
20¾"
8½"
Rafter
Rafter
Pilot
Hole
Roof
Roof
10 3 /8 "
REMOVE
SHINGLES
1¼"
dia. hole
11"
dia.
hole
120 VAC
LINE IN
20½"
Remove BIRD SCREEN and WIRING COVER.
6 Feed the electric power cable through the 1¼" DIAMETER
HOLE and connect cable to ventilator with a proper
connector for the type of cable being used.
7 Connect BLACK TO BLACK, WHITE TO WHITE, and the
GREEN TO GREEN or bare wire. Replace wiring cover.
INSTALL THE VENTILATOR
OUTSIDE - ROOF VIEW
From inside the attic space:
1 Drill a PILOT HOLE up through the roof, 8½" from the inside
edge of a ROOF RAFTER.
Shipping
Cardboard
Remove
roofing
nails from
top 2/3 of
shingles.
Wiring
Cover
2"
Bird Screen
6¾
2"
6
Mounting
Holes
7 Cover
Screws
From outside - on the roof:
2 Measure and mark the 20¾" x 20½" rectangle. Cut and
remove only the shingles inside this rectangle.
3 Measure and mark the 11" DIAMETER HOLE and the 1¼"
DIAMETER HOLE. Cut these holes all the way through the
roof.
"
GREEN
TO
GREEN
5Remove 7 COVER SCREWS and lift off ventilator cover.
9 1 /8 "
7¼"
24¾
WHITE
TO
WHITE
"
"
28¼
Flashing Sheet
OUTSIDE - ROOF VIEW
8Remove SHIPPING CARDBOARD from blower wheel.
9 Remove roofing nails from top 2/3 of shingles around cut-out
area.
For flat roof installations:
4 Build a curb that will mount the blower at a minimum pitch of
2/12. Discharge end of the blower should be pointed away
from prevailing winds.
10 Slide the ventilator's FLASHING SHEET up and under
the loosened shingles until ventilator's discharge collar
fits into 11" diameter hole.
11 Use the 6 screws (provided) to attach the ventilator to the
roof. 6 MOUNTING HOLES are provided.
12 Seal the screw heads, loosened shingles, and edges of
the flashing sheet, with a good grade of roofing cement.
13 Check for free movement of the spring-loaded damper,
re-install BIRD SCREEN and ventilator cover. Turn on
power and check operation.
MODEL 801641
WALL MOUNT
Page 3
INSTALLATION
For use with Models CTWH30, CTWH36, IH4227, DD30R, DD36R, DD45R, W30-662418,
W30-662718, W36-482210, I36-663418, L34-582212.
WIRE THE VENTILATOR
PREPARE THE WALL
BLACK
TO
BLACK
24¾"
10¾"
REMOVE
SIDING
11" dia.
hole
Pilot
Hole
120 VAC
LINE IN
Wall Stud
12 7 /8 "
Wall Stud
8½"
1¼"
dia. hole
28¼"
9 1 /8 "
7¼"
WHITE
TO
WHITE
GREEN
TO
GREEN
4Remove 7 COVER SCREWS and lift off ventilator cover.
Remove BIRD SCREEN and WIRING COVER.
5 Feed the electric power cable through the 1¼" DIAMETER
HOLE and connect cable to ventilator with a proper
connector for the type of cable being used.
6 Connect BLACK TO BLACK, WHITE TO WHITE, and the
GREEN TO GREEN or bare wire. Replace wiring cover.
INSTALL THE VENTILATOR
OUTSIDE - WALL VIEW
From inside the wall:
1 Drill a PILOT HOLE through the wall, 8½" from the inside
edge of a WALL STUD.
6
Mounting
Holes
7 Cover
Screws
From outside - on the wall:
2 Measure and mark the 25" x 29½" rectangle. Cut and remove
only the siding inside this rectangle.
3 Measure and mark the 11" DIAMETER HOLE and the 1¼"
DIAMETER HOLE. Cut these holes all the way through the
wall.
Shipping
Cardboard
Wiring
Cover
Bird Screen
Flashing Sheet
OUTSIDE - WALL VIEW
7Remove SHIPPING CARDBOARD from blower wheel.
8 Place ventilator on wall so that ventilator's discharge collar
fits into 11" diameter hole.
9 Use the 6 screws (provided) to attach the ventilator to the
wall. 6 MOUNTING HOLES are provided.
Seal the screw heads and edges of the flashing sheet with
a good grade of roofing cement.
11 Check for free movement of the spring-loaded damper,
re-install BIRD SCREEN and ventilator cover. Turn on
power and check operation.
10
MODEL 801641
Page 4
ATTACH POWER CORD TO HOOD
Some wall and island hoods (excluding CTWH30, CTWH36, IH4227) require the use of a separate
power cord and strain relief bushing (included), for proper wiring of exterior blowers. Please refer to
the installation instructions supplied with your Wolf hood.
MODEL 801642
Page 1
EXTERIOR VENTILATOR KITS
!
WARNING
CAUTION
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer or your distributor.
2. Before servicing or cleaning unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
3.Installation work and electrical wiring must be done by a
qualified person(s) in accordance with all applicable codes
and standards, including fire-rated construction codes and
standards.
4. Sufficient air is needed for proper combustion and exhausting
of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment
manufacturer’s guidelines and safety standards such as those
published by the National Fire Protection Association (NFPA),
and the American Society for Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE), and the local code authorities.
5.When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. Do not use this unit with an additional speed control device.
8. To reduce the risk of fire, use only steel ductwork.
9. This unit must be grounded.
TO REDUCE THE RISK OF A COOKTOP GREASE FIRE:
1. Never leave surface units unattended at high settings. Boilovers
cause smoking and greasy spillovers that may ignite. Heat oils
slowly on low or medium settings.
2.Always turn hood ON when cooking at high heat or when
cooking flaming foods.
3. Clean ventilating fans frequently. Grease should not be allowed
to accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate for the
size of the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE
EVENT OF A COOKTOP GREASE FIRE, OBSERVE THE
FOLLOWING:*
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or
metal tray, then turn off the burner. BE CAREFUL TO PREVENT
BURNS. If the flames do not go out immediately, EVACUATE
AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN - You may be burned.
3.DO NOT USE WATER, including wet dishcloths or towels violent steam explosion will result.
4. Use an extinguisher ONLY if:
A.You know you have a Class ABC extinguisher and you
already know how to operate it.
B. The fire is small and contained in the area where it started.
C.The fire department is being called.
D. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips” published by NFPA.
1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
2. To avoid motor bearing damage and noisy and/or unbalanced
impellers, keep drywall spray, construction dust, etc. off power
unit.
3. Your ventilator motor has a thermal overload which will automatically shut off the motor if it becomes overheated. The motor
will restart when it cools down. If the motor continues to shut
off and restart, have the hood serviced.
4. Please read specification label on product for further information and requirements.
SPECIFICATIONS
MODEL VOLTS
801642
120
AMPS
3.0
CFM
1200
DUCT SIZE
10" DIA.
PLAN THE INSTALLATION
1. Locate the ventilator so the length of the duct run and number
of elbows and transitions needed are kept to a minimum.
2. Where possible, ventilator should be located between wall
studs or roof rafters.
3. Avoid pipes, wires, or other ductwork that may be running
through the wall.
4. Be sure that there is enough space for any transitions that
may be needed between the ventilator and the connecting
ductwork.
5. For best performance, locate transitions nearest to ventilator.
MODEL 801642
ROOF MOUNT
INSTALLATION
Page 2
For use with Models CTWH30, CTWH36, IH4227, DD30R, DD36R, DD45R, W30-662418, W30-662718,
I36-663418, L34-582212.
WIRE THE VENTILATOR
PREPARE THE ROOF
5Remove 10
15"
1¼" dia. hole
REMOVE SHINGLES
Pilot Hole
(centered
between rafters)
1"
Roof Rafter
Roof Rafter
12 11 /16 "
20½"
11" dia.
hole
COVER SCREWS
and lift off
ventilator cover.
6 Feed the electric
power cable
through the 1¼"
DIAMETER HOLE
and connect cable
to ventilator with a
proper connector
for the type of
cable being used.
7 Connect BLACK
TO BLACK,
WHITE TO BLUE,
and GROUND
TO GROUNDING
SCREW.
GROUND
TO
GROUNDING
SCREW
WHITE
TO
BLUE
120
VAC
LINE
IN
BLACK TO BLACK
9 13 / 16 "
INSTALL THE VENTILATOR
18"
From inside the attic space:
1 Drill a PILOT HOLE up through the roof, centered between
ROOF RAFTERS.
From outside - on the roof:
2 Measure and mark the 18" x 20½" rectangle. Cut and remove
only the shingles inside this rectangle.
3 Measure and mark the 11" DIAMETER HOLE and the 1¼"
DIAMETER HOLE. Cut these holes all the way through the
roof.
10 Cover
Screws
Remove
roofing
nails from
top 2/3 of
shingles.
Flashing
Sheet
Damper
2"
29
Drill 6
Mounting
Holes
½"
Bird Screen
7"
OUTSIDE - ROOF VIEW
8 Remove
22"
2"
For flat roof installations:
4 Build a curb that will mount the blower at a minimum pitch of
2/12. Discharge end of the blower should be pointed away
from prevailing winds.
roofing nails from top 2/3 of shingles around
cut-out area.
9 Slide the ventilator's FLASHING SHEET up and under
the loosened shingles until ventilator's discharge collar
fits into 11" diameter hole.
10 Use the 6 screws (provided) to attach the ventilator
to the roof. DRILL 6 MOUNTING HOLES inside the
ventilator, as necessary.
11 Seal the screw heads, loosened shingles, and edges of
the flashing sheet, with a good grade of roofing cement.
12 Check for free movement of the spring-loaded
DAMPER, and re-install the ventilator cover. Turn on
power and check operation.
MODEL 801642
WALL MOUNT
INSTALLATION
Page 3
For use with Models CTWH30, CTWH36, IH4227, DD30R, DD36R, DD45R, W30-662418, W30-662718,
I36-663418, L34-582212.
WIRE THE VENTILATOR
PREPARE THE WALL
4Remove 10
17"
1¼" dia. hole
14 11 /16 "
Pilot Hole
(centered between studs)
3"
REMOVE
SIDING
11" dia.
hole
Wall Stud
Wall Stud
29½"
COVER SCREWS
and lift off
ventilator cover.
5 Feed the electric
power cable
through the 1¼"
DIAMETER HOLE
and connect cable
to ventilator with a
proper connector
for the type of
cable being used.
6 Connect BLACK
TO BLACK,
WHITE TO BLUE,
and GROUND
TO GROUNDING
SCREW.
GROUND
TO
GROUNDING
SCREW
WHITE
TO
BLUE
120
VAC
LINE
IN
BLACK TO BLACK
INSTALL THE VENTILATOR
11 13 /16 "
22"
Drill 6
Mounting
Holes
10 Cover
Screws
From inside the wall:
1 Drill a PILOT HOLE through the wall, centered between
WALL STUDS.
From outside - on the wall:
2 Measure and mark the 22" x 29½" rectangle. Cut and remove
only the siding inside this rectangle.
3 Measure and mark the 11" DIAMETER HOLE and the 1¼"
DIAMETER HOLE. Cut these holes all the way through the
wall.
Flashing
Sheet
Damper
Bird Screen
OUTSIDE - WALL
ROOF VIEW
7 Place ventilator on wall so that ventilator's discharge collar
fits into 11" diameter hole.
8 Use the 6 screws (provided) to attach the ventilator to the
wall. DRILL 6 MOUNTING HOLES inside the ventilator, as
necessary.
9 Seal the screw heads and edges of the flashing sheet with
a good grade of roofing cement.
10 Check for free movement of the spring-loaded DAMPER
and re-install ventilator cover. Turn on power and check
operation.
MODEL 801642
Page 4
ATTACH POWER CORD TO HOOD
Some wall and island hoods (excluding CTWH30, CTWH36, IH4227) require the use of a separate
power cord and strain relief bushing (included), for proper wiring of exterior blowers. Please refer to
the installation instructions supplied with your Wolf hood.
MODEL 804701
Page 1
EXTERIOR VENTILATOR KITS
!
WARNING
CAUTION
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer or your distributor.
2. Before servicing or cleaning unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
3.Installation work and electrical wiring must be done by a
qualified person(s) in accordance with all applicable codes
and standards, including fire-rated construction codes and
standards.
4. Sufficient air is needed for proper combustion and exhausting
of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment
manufacturer’s guidelines and safety standards such as those
published by the National Fire Protection Association (NFPA),
and the American Society for Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE), and the local code authorities.
5.When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. Do not use this unit with an additional speed control device.
8. To reduce the risk of fire, use only steel ductwork.
9. This unit must be grounded.
TO REDUCE THE RISK OF A COOKTOP GREASE FIRE:
1. Never leave surface units unattended at high settings. Boilovers
cause smoking and greasy spillovers that may ignite. Heat oils
slowly on low or medium settings.
2.Always turn hood ON when cooking at high heat or when
cooking flaming foods.
3. Clean ventilating fans frequently. Grease should not be allowed
to accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate for the
size of the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE
EVENT OF A COOKTOP GREASE FIRE, OBSERVE THE
FOLLOWING:*
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or
metal tray, then turn off the burner. BE CAREFUL TO PREVENT
BURNS. If the flames do not go out immediately, EVACUATE
AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN - You may be burned.
3.DO NOT USE WATER, including wet dishcloths or towels violent steam explosion will result.
4. Use an extinguisher ONLY if:
A.You know you have a Class ABC extinguisher and you
already know how to operate it.
B. The fire is small and contained in the area where it started.
C.The fire department is being called.
D. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips” published by NFPA.
1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
2. To avoid motor bearing damage and noisy and/or unbalanced
impellers, keep drywall spray, construction dust, etc. off power
unit.
3. Your ventilator motor has a thermal overload which will automatically shut off the motor if it becomes overheated. The motor
will restart when it cools down. If the motor continues to shut
off and restart, have the hood serviced.
4. Please read specification label on product for further information and requirements.
SPECIFICATIONS
MODEL VOLTS
804701
120
AMPS
4.3
CFM
1500
DUCT SIZE
10" DIA.
PLAN THE INSTALLATION
1. Locate the ventilator so the length of the duct run and number
of elbows and transitions needed are kept to a minimum.
2. Where possible, ventilator should be located between wall
studs or roof rafters.
3. Avoid pipes, wires, or other ductwork that may be running
through the wall.
4. Be sure that there is enough space for any transitions that
may be needed between the ventilator and the connecting
ductwork.
5. For best performance, locate transitions nearest to ventilator.
MODEL 804701
ROOF MOUNT
Page 2
INSTALLATION
For use with Models CTWH30, CTWH36, IH4227, W30-662418, W30-662718, I36-663418,
L34-582212, DD30R, DD36R, DD45R.
WIRE THE VENTILATOR
PREPARE THE ROOF
5Remove 10
18"
1¼" dia. hole
REMOVE SHINGLES
Pilot Hole
(centered
between rafters)
1"
Roof Rafter
Roof Rafter
12 11 /16 "
20½"
11" dia.
hole
COVER SCREWS
and lift off
ventilator cover.
6 Feed the electric
power cable
through the 1¼"
DIAMETER HOLE
and connect cable
to ventilator with a
proper connector
for the type of
cable being used.
7 Connect BLACK
TO BLACK,
WHITE TO BLUE,
and GROUND
TO GROUNDING
SCREW.
GROUND
TO
GROUNDING
SCREW
WHITE
TO
BROWN
BLUE
120
VAC
LINE
IN
BLACK
BLACKTO
TOBLUE
BLACK
INSTALL THE VENTILATOR
12 5 / 8 "
21"
Drill 6
Mounting
Holes
10 Cover
Screws
From inside the attic space:
1 Drill a PILOT HOLE up through the roof, centered between
ROOF RAFTERS.
From outside - on the roof:
2 Measure and mark the 21" x 20½" rectangle. Cut and remove
only the shingles inside this rectangle.
3 Measure and mark the 11" DIAMETER HOLE and the 1¼"
DIAMETER HOLE. Cut these holes all the way through the
roof.
Remove
roofing
nails from
top 2/3 of
shingles.
Flashing
Sheet
Damper
2"
29
Bird Screen
½"
7"
OUTSIDE - ROOF VIEW
8 Remove roofing nails from top 2/3 of shingles around cut-out
area.
25"
9 Slide the ventilator's FLASHING SHEET up and under the
2"
For flat roof installations:
4 Build a curb that will mount the blower at a minimum pitch of
2/12. Discharge end of the blower should be pointed away
from prevailing winds.
loosened shingles until ventilator's discharge collar fits into
11" diameter hole.
10 Use the 6 screws (provided) to attach the ventilator to the
roof. DRILL 6 MOUNTING HOLES inside the ventilator,
as necessary.
11 Seal the screw heads, loosened shingles, and edges of
the flashing sheet, with a good grade of roofing cement.
12 Check for free movement of the spring-loaded DAMPER,
and re-install the ventilator cover. Turn on power and check
operation.
MODEL 804701
WALL MOUNT
Page 3
INSTALLATION
For use with Models CTWH30, CTWH36, IH4227, W30-662418, W30-662718, I36-663418,
L34-582212, DD30R, DD36R, DD45R.
WIRE THE VENTILATOR
PREPARE THE WALL
4Remove 10
20"
1¼" dia. hole
14 11 /16 "
Pilot Hole
(centered between studs)
3"
REMOVE
SIDING
11" dia.
hole
Wall Stud
Wall Stud
29½"
14 5 / 8 "
25"
COVER SCREWS
and lift off
ventilator cover.
5 Feed the electric
power cable
through the 1¼"
DIAMETER HOLE
and connect cable
to ventilator with a
proper connector
for the type of
cable being used.
6 Connect BLACK
TO BLACK,
WHITE TO BLUE,
and GROUND
TO GROUNDING
SCREW.
GROUND
TO
GROUNDING
SCREW
WHITE
WHITE
TO
TO
BLUE
BROWN
120
VAC
LINE
IN
BLACKTO
TOBLUE
BLACK
BLACK
INSTALL THE VENTILATOR
Drill 6
Mounting
Holes
10 Cover
Screws
From inside the wall:
1 Drill a PILOT HOLE through the wall, centered between
WALL STUDS.
From outside - on the wall:
2 Measure and mark the 25" x 29½" rectangle. Cut and remove
only the siding inside this rectangle.
3 Measure and mark the 11" DIAMETER HOLE and the 1¼"
DIAMETER HOLE. Cut these holes all the way through the
wall.
Flashing
Sheet
Damper
Bird Screen
OUTSIDE - WALL
ROOF VIEW
7 Place ventilator on wall so that ventilator's discharge collar
fits into 11" diameter hole.
8 Use the 6 screws (provided) to attach the ventilator to the
wall. DRILL 6 MOUNTING HOLES inside the ventilator, as
necessary.
9 Seal the screw heads and edges of the flashing sheet with
a good grade of roofing cement.
10 Check for free movement of the spring-loaded DAMPER
and re-install ventilator cover. Turn on power and check
operation.
MODEL 804701
Page 4
ATTACH POWER CORD TO HOOD
Some wall and island hoods (excluding CTWH30, CTWH36, IH4227) require the use of a separate
power cord and strain relief bushing (included), for proper wiring of exterior blowers. Please refer to
the installation instructions supplied with your Wolf hood.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising