Woods Equipment GILL STR48S-2 User's Manual

Woods Equipment GILL STR48S-2 User's Manual
Rev. 3/09/2010
MAN0101
STR48S-2
STR60S-2
STR72S-2
Tested. Proven. Unbeatable.
OPERATOR'S MANUAL
Super Turf Renovator
& Seedbox
TO THE DEALER:
Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual instructions
and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual
are completed before releasing equipment to the owner.
The dealer must complete the online Product Registration form at the Woods Dealer Website which certifies that
all Dealer Check List items have been completed. Please contact your dealer to complete this form. Dealers can
register all Woods product at dealer.WoodsEquipment.com under Product Registration.
Failure to register the product does not diminish customer’s warranty rights.
TO THE OWNER:
Read this manual before operating your Woods equipment. The information presented will prepare you to do a better and
safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become
acquainted with all adjustment and operating procedures before attempting to operate. Replacement manuals can be
obtained from your dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in
the United States and Canada call 1-800-319-6637.
The equipment you have purchased has been carefully engineered and manufactured to provide dependable and
satisfactory use. Like all mechanical products, it will require cleaning and upkeep. Lubricate the unit as specified.
Observe all safety information in this manual and safety decals on the equipment.
For service, your authorized Woods dealer has trained mechanics, genuine Woods service parts, and the necessary
tools and equipment to handle all your needs.
Use only genuine Woods service parts. Substitute parts will void the warranty and may not meet standards required for
safe and satisfactory operation. Record the model number and serial number of your equipment in the spaces
provided:
Model: _______________________________
Date of Purchase: _____________________
Serial Number: (see Safety Decal section for location) ____________________________________
Provide this information to your dealer to obtain correct repair parts.
Throughout this manual, the term NOTICE is used to indicate that failure to observe can cause damage to equipment.
The terms CAUTION, WARNING, and DANGER are used in conjunction with the Safety-Alert Symbol (a triangle with
an exclamation mark) to indicate the degree of hazard for items of personal safety.
2 Introduction
Gen’l (Rev. 3/5/2010)
TABLE OF CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
OWNER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
ASSEMBLY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
PARTS INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
BOLT TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
BOLT SIZE CHART & ABBREVIATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . .25
REPLACEMENT PARTS WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
PRODUCT WARRANTY . . . . . . . . . . . . . . . . . . . . . . . INSIDE BACK COVER
!
LEA EL INSTRUCTIVO!
Si no lee Ingles, pida ayuda a
alguien que si lo lea para que le
traduzca las medidas de seguridad.
MAN0101 (Rev. 9/15/2006
Introduction 3
SPECIFICATIONS
Super Turf Renovator
STR48S
STR60S
STR72S
Working Width
47"
59"
71"
Overall Width
58"
70"
82"
1/2" x 1-3/4"
1/2" x 1-3/4"
1/2" x 1-3/4"
Six 1"
Six 1"
Six 1"
Roller Pins
Bearing (Self-Aligning)
Front Roller Positions
Adjustable for Increased Agitation
Roller Diameter: Front & Rear
8"
8"
8"
Cat. I
Cat. I
Cat. I
65 HP Max.
65 HP Max.
65 HP Max.
STR48: 565 lbs.
STR60: 710 lbs.
STR72: 855 lbs.
Weight w/Seedbox
STR48S: 820 lbs.
STR60S: 920 lbs.
STR72S: 1050 lbs.
Seedbox Capacity
3 Bushel
4 Bushel
5 Bushel
Hitch
Tractor HP Requirement
Weight
Seed Distribution Method
Metered gear with flow adjustment lever
GENERAL INFORMATION
The purpose of this manual is to assist you in operating
and maintaining your Super Turf Renovator. Read it
carefully. It furnishes information and instructions that
will help you achieve years of dependable performance. These instructions have been compiled from
extensive field experience and engineering data. Some
information may be general in nature due to unknown
and varying operating conditions. However, through
experience and these instructions, you should be able
to develop procedures suitable to your particular situation.
The illustrations and data used in this manual were current at the time of printing but, due to possible inline
production changes, your machine may vary slightly in
4 Introduction
detail. We reserve the right to redesign and change the
machines as may be necessary without notification.
WARNING
■
Super Turf Renovator should never be operated with any safety shielding removed.
Throughout this manual, references are made to right
and left direction. These are determined by standing
behind the equipment facing the direction of forward
travel.
(Rev 3/09/2010)
MAN0101 (Rev. 9/15/2006)
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Safety is a primary concern in the design and
manufacture of our products. Unfortunately, our
efforts to provide safe equipment can be wiped
out by an operator’s single careless act.
In addition to the design and configuration of
equipment, hazard control and accident prevention are dependent upon the awareness, concern, judgement, and proper training of
personnel involved in the operation, transport,
maintenance, and storage of equipment.
It has been said, “The best safety device is an
informed, careful operator.” We ask you to be
that kind of operator.
fastened. Falling off power unit can result in death
from being run over or crushed. Keep foldable
ROPS system in “locked up” position at all times.
„ Make sure all safety decals are installed.
Replace if damaged. (See Safety Decals section for
location.)
„ A minimum 20% of tractor and equipment
weight must be on the tractor front wheels when
attachments are in transport position. Without this
weight, tractor could tip over, causing personal
injury or death. The weight may be attained with a
loader, front wheel weights, ballast in tires or front
tractor weights. Weigh the tractor and equipment.
Do not estimate.
TRAINING
OPERATION
„ Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replacement manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
the Dealer Locator at www.WoodsEquipment.com,
or in the United States and Canada call 1-800-3196637.) Failure to follow instructions or safety rules
can result in serious injury or death.
„ Keep bystanders away from equipment.
„ If you do not understand any part of this manual
and need assistance, see your dealer.
„ Always comply with all state and local lighting
and marking requirements.
„ Know your controls and how to stop engine and
attachment quickly in an emergency.
„ Never allow riders on power unit or attachment.
„ Operators must be instructed in and be capable
of the safe operation of the equipment, its attachments, and all controls. Do not allow anyone to
operate this equipment without proper instructions.
„ Never allow children or untrained persons to
operate equipment.
PREPARATION
„ Check that all hardware is properly installed.
Always tighten to torque chart specifications
unless instructed otherwise in this manual.
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
„ Make sure attachment is properly secured,
adjusted, and in good operating condition.
„ Power unit must be equipped with ROPS or
ROPS cab and seat belt. Keep seat belt securely
STR48-72 Safety Rules (Rev. 7/28/2005)
„ Do not operate or transport equipment while
under the influence of alcohol or drugs.
„ Operate only in daylight or good artificial light.
„ Keep hands, feet, hair, and clothing away from
equipment while engine is running. Stay clear of all
moving parts.
„ Power unit must be equipped with ROPS or
ROPS cab and seat belt. Keep seat belt securely
fastened. Falling off power unit can result in death
from being run over or crushed. Keep foldable
ROPS system in “locked up” position at all times.
„ Always sit in power unit seat when operating
controls or starting engine. Securely fasten seat
belt, place transmission in neutral, engage brake,
and ensure all other controls are disengaged
before starting power unit engine.
„ Look down and to the rear and make sure area
is clear before operating in reverse.
„ Use extreme care when working close to fences,
ditches, other obstructions, or on hillsides.
„ Do not operate or transport on steep slopes.
„ Do not stop, start, or change directions suddenly on slopes.
„ Use extreme care and reduce ground speed on
slopes and rough terrain.
(Safety Rules continued on next page)
Safety 5
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
(Safety Rules continued from previous page)
„ Watch for hidden hazards on the terrain during
operation.
„ Stop power unit and equipment immediately
upon striking an obstruction. Turn off engine,
remove key, inspect, and repair any damage before
resuming operation.
MAINTENANCE
„ Before dismounting power unit or performing
any service or maintenance, follow these steps:
disengage power to equipment, lower the 3-point
hitch and all raised components to the ground,
operate valve levers to release any hydraulic pressure, set parking brake, stop engine, remove key,
and unfasten seat belt.
„ NEVER GO UNDERNEATH EQUIPMENT. Never
place any part of the body underneath equipment
or between moveable parts even when the engine
has been turned off. Hydraulic system leak-down,
hydraulic system failures, mechanical failures, or
movement of control levers can cause equipment
to drop or rotate unexpectedly and cause severe
injury or death.
• Service work does not require going underneath.
• Read Operator's Manual for service instructions or have service performed by a qualified
dealer.
6 Safety
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
„ Make sure attachment is properly secured,
adjusted, and in good operating condition.
„ Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.
„ Tighten all bolts, nuts, and screws to torque
chart specifications. Check that all cotter pins are
installed securely to ensure equipment is in a safe
condition before putting unit into service.
„ Make sure all safety decals are installed.
Replace if damaged. (See Safety Decals section for
location.)
STORAGE
„ Block equipment securely for storage.
„ Keep children and bystanders away from storage area.
™
STR48-72 Safety Rules (Rev. 7/28/2005)
SAFETY & INSTRUCTIONAL DECALS
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Replace Immediately If Damaged!
MODEL NO.
SERIAL NO.
Woods Equipment Company
Oregon, Illinois, U.S.A.
3 - Serial Number Plate
6 - PN 20106 Red Reflector
9 - PN 24611 Slow Moving Vehicle
4 - PN 15502
WARNING
ROTATING COMPONENTS
5 - PN 18868
Do not operate without cover in place.
Look and listen for rotation. Do not
open cover until all components have
stopped.
SHIELD MISSING
CONTACT WITH ROTATING PARTS
CAN CAUSE SERIOUS INJURY.
Do not operate.
Put shield on.
DANGER
15502--B
18868-B
BE CAREFUL!
Use a clean, damp cloth to clean safety decals.
Avoid spraying too close to decals when using a pressure washer; high-pressure water can
enter through very small scratches or under edges of decals causing them to peel or come off.
Replacement safety decals can be ordered free from your Woods dealer. To locate your
nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United
States and Canada call 1-800-319-6637.
(Safety Decals continued on next page)
MAN0101 (Rev.9/15/2006)
Safety 7
SAFETY & INSTRUCTIONAL DECALS
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Replace Immediately If Damaged!
(Safety Decals continued
from previous page)
WARNING
FALLING OFF CAN RESULT IN BEING RUN OVER.
„ Tractor must be equipped with ROPS (or ROPS CAB) and
seat belt. Keep foldable ROPS systems in “locked up”
position at all times.
„ Buckle Up! Keep seat belt securely fastened.
„ Allow no riders.
RAISED IMPLEMENT CAN DROP AND CRUSH.
„ Never go underneath raised implement which can drop
from equipment or tractor 3-point hitch hydraulic leak
down, hydraulic system failures, movement of control
levers or mechanical linkage failures.
„ Service work does not require going underneath
implement. Read manual instructions.
FALLING OFF OR GOING UNDERNEATH IMPLEMENT
CAN RESULT IN SERIOUS INJURY OR DEATH.
55121--C
1 - PN 55121
7 - PN 1003751
2 - PN 55122
WARNING
WARNING
TO AVOID SERIOUS INJURY OR DEATH:
Read Operator's Manual before operating, servicing or
repairing equipment. Follow all safety rules and
instructions. (Manuals are available from dealer or call
1-800-319-6637.)
Operate from tractor seat only.
Lower equipment to ground, stop engine, remove key
and set brake before dismounting tractor.
Never allow children or untrained persons to operate
equipment.
Never allow riders.
Keep bystanders away from equipment during operation.
Keep all shields in place and in good condition.
Do not transport towed or semi-mounted units over 20
mph.
CRUSHING AND PINCHING HAZARD
Be extremely careful handling various parts of
FAILURE TO FOLLOW THESE INSTRUCTIONS CAN
RESULT IN INJURY OR DEATH.
55122-D
the machine. They are heavy and hands, fingers,
feet, and other body parts could be crushed or
pinched between tractor and implement.
Operate tractor controls from tractor seat only.
Do not stand between tractor and implement
when tractor is in gear.
Make sure parking brake is engaged before
going between tractor and implement.
Stand clear of machine while in operation or
when it is being raised or lowered.
FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD RESULT IN
SERIOUS INJURY OR DEATH.
1003751-A
WARNING
ENTANGLEMENT AND
FALLING HAZARD
Do not stand on rollers while machine is in
operation or parked.
8 - PN 1003750
8 Safety
Failure to follow these instructions
could result in serious injury or
death.
1003750
MAN0101 (Rev. 9/15/2006)
OPERATION
The operator is responsible for the safe operation of
this renovator. The operator must be properly trained.
Operators should be familiar with the equipment, the
tractor, and all safety practices before starting operation. Read the safety rules and safety decals on page 5
through page 8.
Recommended tractor ground speed is from 2 to 5
mph.
WARNING
„ Power unit must be equipped with ROPS or
ROPS cab and seat belt. Keep seat belt securely
fastened. Falling off power unit can result in death
from being run over or crushed. Keep foldable
ROPS system in “locked up” position at all times.
„ Never allow children or untrained persons to
operate equipment.
„ Keep bystanders away from equipment.
„ Keep hands, feet, hair, and clothing away from
equipment while engine is running. Stay clear of all
moving parts.
DP6
Figure 1. Front Roller in Straight Position
The front rollers can be angled to promote a more
aggressive tearing action of the turf. The more the
angle, the more tearing action is applied by the front
roller pins. For severe turf conditions, the maximum
angle position may be desired (Figure 2).
CAUTION
„ Stop power unit and equipment immediately
upon striking an obstruction. Turn off engine,
remove key, inspect, and repair any damage before
resuming operation.
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
Super Turf Renovator Roller Operation
The Super Turf Renovator is an excellent turf reconditioning tool. Its ground penetration promotes a healthy
root system by allowing water, air, and sunlight to enter
the roots.
For best results, adjust the renovator level front to back
so that the front and rear rollers work together. Control
forward and backward pitch by adjusting the tractor's
top link length.
DP7
Figure 2. Maximum Front Roller Position
Front Rollers
Rear Rollers
When the front rollers are straight (Figure 1) and the
renovator is pulled forward, the large front pins will
penetrate the soil in a straight pushing action, and little
disturbance is caused to the turf.
The rear roller firms and presses soil kicked up by the
front roller. This creates a uniform seedbed with the
loose soil necessary for ensuring proper seed germination. The spring tension on the rear roller can be
MAN0101 (Rev. 9/15/2006)
Operation 9
adjusted to deliver the desired down pressure and
roller action and achieve the desired seedbed appearance.
1. Attach the tractor’s lower lift arms to the renovator
and secure with mounting pins (11) and klik pins.
See Figure 4.
When the situation permits, making a second pass 90degrees to the first is an effective way for the roller pins
to penetrate areas where uneven soil conditions exist.
In extremely compacted soil conditions, add extra
weight to the renovator to help the roller pins penetrate
the turf and soil sufficiently.
11
Operation
The power for operating the renovator comes from contact between the renovator rollers and the turf.
Know how to stop the tractor and renovator quickly in
an emergency.
Survey the area to be worked and remove any obstructions that may affect the performance of the equipment.
Tractor Stability
WARNING
„ A minimum 20% of tractor and equipment
weight must be on the tractor front wheels when
attachments are in transport position. Without this
weight, front tractor wheels could raise up resulting in loss of steering. The weight may be attained
with front wheel weights, ballast in tires or front
tractor weights. Weigh the tractor and equipment.
Do not estimate.
DP1
Figure 4. Lift Arms Attached to Renovator
2. Attach the tractor’s top link to the upper mast of the
renovator. Secure with high-strength top link pin
and retaining pin provided with the tractor. See
Figure 5.
Top Link Pin
DP2
Figure 5. Top Link Attached to Renovator
Figure 3. Tractor Stability
Attach Super Turf Renovator to Tractor
NOTE: Super Turf Renovator is designed for use on
Category I, 3-point tractors. See page 4 for specifications.
10 Operation
3. Adjust top link as needed to level the renovator
forward and backwards.
4. Adjust the lower lift arm anti-sway device to
prevent the renovator from excessive side-to-side
movement.
NOTE: An optional Quick Hitch Mounting Kit is available.
MAN0101 (Rev. 9/15/2006)
Adjust Front Roller Angle
1. Position tractor and renovator on a level surface.
6. Install lock assembly (5), lock pin (15), and klik pin
(21) to secure front roller into position.
7. Reverse this procedure to move front roller back
into normal position.
2. Raise renovator slightly off the ground.
3. Stop engine and set parking brake.
4. Remove klik pin (21), lock pin (15), and lock
assembly (5) from front of renovator. See Figure 6.
15
Seeding Operation
Tractor speed and seed flow settings are critical for
proper seed population. Check the seed control chart,
on the inside of the seedbox lid (see page 11). Adjust
the flow control handle (Figure 8) as needed for the
seed being used and the population desired.
Tractor speed (normally 2-5 mph) should be established so that uniform seed incorporation occurs with
the action of the rollers. The seed chart is based on a
standard sprocket configuration. Any adjustments to
this ratio will result in a change to the flow rate, as
described in the chart.
5
NOTE: The seed control chart should be used as a
general guide only.
DP3
21
Figure 6. Lock Pin and Lock Assembly
5. Raise the adjustment handle (16) and pivot it to the
next adjustment hole. Move handle rearward, front
roller will start to angle. Continue this process until
front roller has the desired angle.
Before seeding an area, check the attitude of the
seeder and adjust the top link so that the front and rear
rollers are level. Adjust the 3-point lower lift stop so that
the roller spikes penetrate the ground at 3/4" or enough
to remove the tracks left by the tractor tires.
OPEN
CLOSED
16
DP4
Figure 7. Adjustment Handle
MAN0101 (Rev. 9/15/2006)
DP7
Figure 8. Flow Control Handle
Operation 11
Operating Tips
Pre-Operation Check List
(OWNER’S RESPONSIBILITY)
IMPORTANT
■ Before closing down the cup (reducing rates),
the operator should make certain that the cups are
not full of seed. If cups are full of seed (especially
small, round, hard seed), it may be necessary to
cover the meter holes and run seeder a short distance to reduce level of seeds in meter. Failure to
do so could result in damage to seed cup.
1. Do not allow dirt to build up on the roller sprockets.
Clean sprockets and chain as needed. Excessive
buildup of material can cause damage to the roller
and idler shafts.
2. Always run the drive chain with some slack in the
chain. An extremely tight chain can damage the
roller shaft, the roller bearings, and the idler shaft
and bearing.
3. When properly torqued, the hex lock nut (1) drives
the seedbox roller chain. Disengage the seedbox
chain, when not in use, by backing off a 1/4 turn on
the lock nut.
___ Review and follow all safety rules and safety
decal instructions on page 5 through page 8.
___ Check that equipment is properly and securely
attached to tractor.
___ Check that all safety decals are installed and in
good condition. Replace if damaged.
___ Do not allow riders.
___ Check that all hardware is properly installed and
secured.
___ Check that shields and guards are properly
installed and in good condition. Replace if damaged.
___ Check all lubrication points and grease as
instructed in Lubrication Information, page 12.
___ Make sure tractor ROPS or ROPS cab and seat
belt are in good condition. Keep seat belt
securely fastened during operation.
™
1 1
DP8DP8
Figure 9. Drive Chains
12 Operation
MAN0101 (Rev. 9/15/2006)
MAN0101 (Rev. 9/15/2006)
Operation 13
1-1/4
3-1/4
5
6-3/4
1/4 Open*
1/2 Open
3/4 Open
Full Open
291
216
142
52
Lbs per
Acre
7
5-1/4
3-1/2
1-1/4
Lbs per
1000 Sq Ft
298
224
149
52
Lbs per
Acre
Bermuda
(hulled)
2-1/2
2
1-1/4
1/2
Lbs per
1000 Sq Ft
104
82
52
22
Lbs per
Acre
Blue Grass
(Kentucky)
6-1/2
5-1/4
3-1/4
1-1/2
Lbs per
1000 Sq Ft
298
224
142
67
Lbs per
Acre
Clover
(sweet, red)
74
99
2-1/4
50
18
Lbs per
Acre
1-3/4
1-1/4
1/2
Lbs per
1000 Sq Ft
Fescue
(creeping red)
3-3/4
2-3/4
2
1-1/4
Lbs per
1000 Sq Ft
1001998
Lbs per
Acre
5. Turn rear roller in the direction of travel the number of revolutions as
indicated in the Formula section.
4. Open seed cups half way and lock into position.
3. Place a canvas or trap under STR to collect seed.
2. Raise STR just enough to lift rear roller spikes off the ground and
securely block the rear corners of the frame with jack stands. Blocking
up prevents hydraulic leak down or mechanical component failure.
1. Evenly distribute seed in the bottom of seed box.
Procedure
4. One scale capable of measuring ounces or tenths of a pound.
3. One tarp or canvas approximately 48" x 84".
2. One to two pound sample of seed.
1. Two jack stands.
STR48 rear roller was rotated 87 complete revolutions in the direction
of travel as specified above. Collected seed weighed 10 ounces or .63
pounds (10 oz. x .0625 = .63 lbs). Seed rate was calibrated at .63 lbs. x
43.56 = 27.4 lbs. of seed per acre.
Example
Seed per acre
(___ lbs. x 43.56 = ___ lbs. per acre)
Weight of collected seed
(___oz. x .0625 = ___ lbs.)
Revolutions per 1000 sq. ft.
STR48 - 87
STR60 - 69
STR72 - 58
Formula
7. If seed rate is not correct, repeat steps 1 through 6, after adjusting
the seed cup opening.
Lbs per
1000 Sq Ft
You will need the following equipment to calibrate your seeder.
268
194
119
45
Lbs per
Acre
6. Weigh the collected seed and calibrate.
6-1/4
4-1/2
2-3/4
1
Lbs per
1000 Sq Ft
Timothy
Equipment
165
116
83
50
Lbs per
Acre
Italian Rye
Calibrating the STR for unlisted seed or seed blends
Rates are intended as a guide only. Variation in seed size and cleanliness will affect rates.
Check acreage and pounds of seed used and calibrate seeding rate per manual instructions for best results.
*Seed cups will crack some seeds at this setting. Not recommended: Lentils, Sorghum, Sudan Grass
Lbs per
1000 Sq Ft
Setting
Alfalfa
(uncoated)
SEEDING RATE CHART
OWNER SERVICE
The information in this section is written for operators
who possess basic mechanical skills. If you need help,
your dealer has trained service technicians available.
For your protection, read and follow the safety information in this manual.
WARNING
„ NEVER GO UNDERNEATH EQUIPMENT. Never
place any part of the body underneath equipment
or between moveable parts even when the engine
has been turned off. Hydraulic system leak-down,
hydraulic system failures, mechanical failures, or
movement of control levers can cause equipment
to drop or rotate unexpectedly and cause severe
injury or death.
• Service work does not require going underneath.
• Read Operator's Manual for service instructions or have service performed by a qualified
dealer.
„ Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.
„ Before dismounting power unit or performing
any service or maintenance, follow these steps:
disengage power to equipment, lower the 3-point
hitch and all raised components to the ground,
operate valve levers to release any hydraulic pressure, set parking brake, stop engine, remove key,
and unfasten seat belt.
CAUTION
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
A
C
B
Figure 10. Lubrication Points
Cleaning
After Each Use
●
Remove large debris such as clumps of dirt, grass,
crop residue, etc. from machine.
●
Inspect machine and replace worn or damaged
parts.
●
Replace any safety decals that are missing or not
readable.
Periodically or Before Extended Storage
●
Clean large debris such as clumps of dirt, grass,
crop residue, etc. from machine.
●
Remove the remainder using a low-pressure water
spray.
1. Be careful when spraying near scratched or torn
safety decals or near edges of decals as water
spray can peel decal off surface.
2. Be careful when spraying near chipped or
scratched paint as water spray can lift paint.
Lubrication Information
1. Lubricate all six bearings housings every 8 hours.
Bearing housing are located on each end of rollers
as indicated by grease fitting (A). See Figure 10.
3. If a pressure washer is used, follow the advice
of the pressure washer manufacturer.
●
Inspect machine and replace worn or damaged
parts.
●
Sand down scratches and the edges of areas of
missing paint and coat with Woods spray paint of
matching color (purchase from your Woods
dealer).
●
Replace any safety decals that are missing or not
readable (supplied free by your Woods dealer).
See Safety Decals section for location drawing.
2. Lubricate grease fittings (B) & (C) every 8 hours.
3. Clean fittings prior to lubrication. Do not let
excessive grease build up around lubrication
points.
NOTE: One pump of a good grade multi-purpose
grease should be sufficient in most cases. Harsh or dry
conditions may require more frequent lubrication.
14 Owner Service
MAN0101 (Rev.9/15/2006)
ASSEMBLY
DEALER SET-UP INSTRUCTIONS
Assembly of this equipment is the responsibility of the
Woods dealer. It should be delivered to the owner completely assembled, lubricated, and adjusted for normal
operating conditions.
12
15
In most cases the Super Turf Renovator is shipped
completely assembled from the factory. The seed box
is an option that can be added to the Super Turf Renovator at a later time if desired.
Install Seedbox
1. Place seedbox on top of renovator mounting
saddles.
2. Install four carriage bolts (18) from underneath
saddles and secure with flanged lock nuts (19).
See Figure 11.
3. Do not tighten until all adjustments are completed.
12
13
DP10
12. 3/4 Flat washer
13. Drive sprocket, 18T w/bearing
15. 3/4 NC Nylok Jam nut
Figure 12. Drive Sprocket Installed
Install Idler Bracket
1. Remove hex nuts (31) and hardened flat washers
(30) from cap screws securing the spring bracket to
the renovator. See Figure 13.
2. Place idler bracket assembly over cap screws and
install washers (30) and hex nuts (31) previously
removed. See Figure 14.
18
19
DP11
18. 5/8 NC x 1-1/2 Carriage bolt GR5
19. 5/8 NC Flange lock nut
Figure 11. Seedbox Hardware Installed
30 31
Install Drive Sprocket
30 31
1. Place washers (12), sprocket (13), and lock nut
(15) on the left side of rear roller drive axle (Figure
12).
2. Do not tighten nut at this time.
NOTE: When properly torqued, the hex lock nut drives
the seedbox roller chain. Disengage the seedbox chain
when not in use by backing off a 1/4 turn on the lock
nut.
DP12
30. 5/8 Hardened flat washer
31. 5/8 NC Hex nut
Figure 13. Spring Bracket and Hardware
MAN0101 (Rev.10/15/2004)
Assembly 15
5. Slide idler bracket assembly forward to apply
tension to the horizontal drive chain.
6. Slide idler and spring bracket down to apply
tension to the vertical drive chain.
NOTE: Do not over tighten. Allow some slack in chain.
Idler Bracket
Assembly
7. Adjust opposite side of roller to level.
30 31
A
30 31
Idler Bracket
Assembly
DP14
Figure 14. Idler Bracket Assembly Installed
Install Roller Chains
1. Place roller chain (A - 35 link) around the seed box
sprocket and the large inner sprocket on the idler
bracket assembly. Secure chain using master link.
2. Install roller chain (B - 28 link) around the rear drive
sprocket and smaller outer sprocket on the idler
bracket assembly. Secure chain using master link.
3. Align the seed box sprocket and large inner
sprocket on the idler bracket by adjusting seed box
side to side.
DP13
B
A. Roller chain 35-LK w/adjustable links
B. Roller chain 28-LK w/adjustable links
Figure 15. Sprockets and Chains Installed
4. Tighten hardware securing seed box to renovator
frame.
™
16 Assembly
MAN0101 (Rev.10/15/2004)
PARTS INDEX
Super Turf Renovator
& Seedbox Kit
STR48S-2
STR60S-2
STR72S-2
Main Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 - 19
Seedbox Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 - 21
Drive Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Quick Hitch Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
MAN0101 (Rev. 9/15/2006)
Parts 17
STR48S-2, STR60S-2 & STR72S-2 MAIN ASSEMBLY
18 Parts
MAN0101 (Rev. 9/15/2006)
STR48S-2, STR60S-2 & STR72S-2 MAIN ASSEMBLY PARTS LIST
REF
1
STR 48-2
…………
STR 60-2
…………
STR72-2
…………
QTY
DESCRIPTION
1
STR Frame
2
1000778
1000778
1000778
1
Rear roller arm, right
3
1000779
1000779
1000779
1
Rear roller arm, left
4
D2213
D2213
D2213
4
Bushing, 0.88 ID
5
1002912
1001716
1001716
1
Lock assembly
6
1001984
1001984
1001984
2
Spring pin, .75 x 11.8
7
20A125
20A125
20A125
2
Compression spring
8
20A920
20A920
20A920
6
Bearing w/housing
9
46483
46483
46483
2
Sleeve, .82 x 1.05 x .66
10
1002018
1002018
1002018
1
Sleeve, .81 x 1.25 x 2.06
11
SU105
SU105
SU105
2
Category 1 drawbar pin w/lynch pin
12
SU106
SU106
SU106
1
Spring bracket, left
13
SU107
SU107
SU107
1
Spring bracket, right
14
…………
…………
…………
1
Slide plate
15
1002914
1002914
1002914
1
Lock pin
16
SU905
SU905
SU905
1
STR Handle
17
100292548
100292560
100292572
2
Roller retainer assembly
18
100290848
100290860
100290872
1
Rear roller assembly
19
100290948
100290960
100290972
2
Front roller assembly
20
13759*
13759*
13759*
2
3/4 NC x 2-1/4 Cap screw GR5
21
27542*
27542*
27542*
1
7/16 x 11/32 Klik pin HT
22
2864*
2864*
2864*
4
3/4 SAE Flat washer
23
14334*
14334*
14334*
2
3/4 NC x 3 Cap screw GR5
24
FA446
FA446
FA446
5
3/4 NC Nylok nut
25
835*
835*
835*
3
3/8 NC Hex nut
26
31207*
31207*
31207*
1
3/4 NC x 4 Cap screw GR5
27
29485*
29485*
29485*
4
3/4 Hex jam nut
28
3231*
3231*
3231*
1
3/8 NC x 2 Cap screw GR5
29
34473*
34473*
34473*
4
5/8 NC x 3 Cap screw GR5
30
57817
57817
57817
8
5/8 Hardened flat washer
31
230*
230*
230*
4
5/8 NC Hex nut
32
838*
838*
838*
29
3/8 Lock washer
33
976*
976*
976*
26
3/8 NC x 1-1/2 Cap screw GR5
34
300157*
300157*
300157*
2
3/8 NC x 2-1/4 Cap screw GR5
35
1002943
1002943
1002943
2
.82 x 1.06 x .407 Sleeve
36
1002942
1002942
1002942
4
.68 x 1.02 x .66 Sleeve
37
1003828
1003828
1003828
1
Manual tube
38
1002934
1002934
1002934
—
Safety decal set
39
1002935
1002935
1002935
—
Complete decal set
40
1002938
1002938
1002938
—
Replacement pins (25-pin set)
* Obtain Locally
MAN0101 (Rev. 9/15/2006)
Parts 19
STR48-2, STR60S-2 & STR72S-2 SEEDBOX ASSEMBLY
20 Parts
MAN0101 (Rev. 9/15/2006)
STR48-2, STR60S-2 & STR72S-2 SEEDBOX PARTS LIST
REF
1
2
3
4
5
STR 48-2
1000001
100001348
…………
1000766
100293248
STR 60-2
1000001
100001360
…………
1000766
100293260
STR72-2
1000001
100001372
…………
1000766
100293272
QTY
1
1
1
1
1
6
100293348
100293360
100293372
1
7
8
9
10
11
12
13
14
15
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
47
48
49
50
51
1000782
1000783
1000784
1000787
1000790 (8)
1001705
1001721
100172248
46490 (8)
1001986
1001987
1001988 (6)
1001993
1001992
20A653
20A654
20A656
1001997
20A663
20A664 (16)
20A687
20A765
1001714 (8)
20A635
1001978*
1002016*
FA159*
70065 (36)
1001975
1001994*
12169*
14350*
3231*
70067 (22)
70068
6697*
66840
1001995 (16)*
FA404*
FA405*
1006607
24611
1000782
1000783
1000784
1000787
1000790 (10)
1001705
1001721
100172260
46490 (10)
1001986
1001987
1001988 (8)
1001993
1001992
20A653
20A654
20A656
1001997
20A663
20A664 (20)
20A687
20A765
1001714 (10)
20A635
1001978*
1002016*
FA159*
70065 (40)
1001975
1001994*
12169*
14350*
3231*
70067 (26)
70068
6697*
66840
1001995 (20)*
FA404*
FA405*
1006607
24611
1000782
1000783
1000784
1000787
1000790 (12)
1001705
1001721
100172272
46490 (12)
1001986
1001987
1001988 (10)
1001993
1001992
20A653
20A654
20A656
1001997
20A663
20A664 (24)
20A687
20A765
1001714 (12)
20A635
1001978*
1002016*
FA159*
70065 (44)
1001975
1001994*
12169*
14350*
3231*
70067 (30)
70068
6697*
66840
1001995 (24)*
FA404*
FA405*
1006607
24611
2
1
1
1
MAN0101 (Rev. 9/15/2006)
2
1
1
1
DESCRIPTION
Seedbox support bracket, left
Shaft, .38 square w/holes
Center stiffener
Seedbox support bracket, right
Seedbox assembly complete
(3 & Decals)
Lid assembly complete
(13, 32, 37, & decal)
Bearing double row, 17 x 40 x .5 mm
Bearing block
Agitator shaft assembly
Seedcup shaft assembly
Compression spring
Control lever
Seedbox hinge, 36"
Shaft, .38 square
Seedcup kit
Spacer, 1.22
Spacer, 2.56
Spacer, 5.88
Spool assembly
Control plate
Spur gear agitator (28T)
Spur gear feed (30T)
Sprocket (15T)
Agitator bracket
Bushing, .5 x .75 x .75
Agitator washer
Collar
Spacer, .75
Washer, .44 square hole
Lid handle
Blind rivet 3/16, #.63
Chain, #2 double loop 9 link
Eye bolt, 1/4 - 20 x 1
1/4 NC Whiz nut
Flex draw latch
Blind rivet 1/8, #.43
3/8 NC x 1-1/4 Cap screw GR5
3/8 NC Flange lock nut
3/8 NC x 2 Cap screw GR5
1/4-20 x 1/2 Whiz bolt
1/4-20 x 3/4 Whiz bolt
3/8 NC x 1 Carriage bolt
3 Prong knob, 3/8 NC
1/8 x 1 Roll pin
1/8 x 1-1/2 Roll pin
1/8 x 1-3/4 Roll pin
SMV Bracket
Sign, (SMV) slow moving vehicle
*
Obtain Locally
1
1
1
1
2
1
1
1
1
1
2
2
1
1
1
18
2
4
2
6
10
11
2
6
1
1
Parts 21
STR48-2, STR60S-2 & STR72S-2 DRIVE ASSEMBLY
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
STR 48-2
…………
…………
1001710
7832*
57817*
230
1000791
1001983
1002930
1002931
35139*
1257*
SU613
12296*
56722
1001709
66840
5607*
19025*
FA419
100293648
1002939
1001975
1001994*
12169*
14350*
1002934
1002935
1002959
STR 60-2
…………
…………
1001710
7832*
57817*
230
1000791
1001983
1002930
1002931
35139*
1257*
SU613
12296*
56722
1001709
66840
5607*
19025*
FA419
100293660
1002939
1001975
1001994*
12169*
14350*
1002934
1002935
1002959
STR72-2
…………
…………
1001710
7832*
57817*
230
1000791
1001983
1002930
1002931
35139*
1257*
SU613
12296*
56722
1001709
66840
5607*
19025*
FA419
100293672
1002939
1001975
1001994*
12169*
14350*
1002934
1002935
1002959
QTY
1
1
1
2
2
2
1
1
1
1
1
2
1
1
1
1
3
4
4
2
1
1
2
4
2
2
—
—
1
DESCRIPTION
Seedbox assembly
STR Assembly
Chain guard bracket
5/8 NC x 1-1/2 Cap screw GR5
5/8 Heavy lock washer
5/8 NC Hex nut
Idler bracket
Idler sprocket w/bearing
Roller chain 35-LK with adjustment links
Roller chain 28-LK with adjustment links
Retainer ring, .05 x .75
3/4 Flat washer
Drive sprocket w/bearing
1/4-28 x 15/32 Grease fitting
3/4 NC Nylok jam nut
Chain guard
3 Prong knob, 3/8 NC
5/8 NC x 1-1/2 Carriage bolt GR5
5/8 NC Flanged lock nut
Connector link
Deflector assembly, (includes item #23)
End support
Flex draw latch
Blind rivet
3/8 NC X 1-1/4 Hex head cap screw GR5 ZP
3/8 NC Flange lock nut
Safety decal set
Complete decal set
#40 SGL Pitch offset link
* Obtain Locally
22 Parts
MAN0101 (Rev. 9/15/2006)
STR48-2, STR60S-2 & STR72S-2 QUICK HITCH KIT
REF PART
1
2
MAN0101 (Rev. 9/15/2006)
…………
1001702
QTY DESCRIPTION
1
STR Frame
2
Quick hitch sleeve
Parts 23
BOLT TORQUE CHART
Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific
application.
Fasteners must always be replaced with the same grade as specified in the manual parts list.
Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware.
Make sure fastener threads are clean and you start thread engagement properly.
All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.
SAE Bolt Head
Identification
SAE SERIES
TORQUE
CHART
A
SAE Grade 2
(No Dashes)
SAE Grade 8
(6 Radial Dashes)
SAE Grade 5
(3 Radial Dashes)
MARKING ON HEAD
A
Diameter
(Inches)
Wrench
Size
SAE 2
lbs-ft
SAE 5
N-m
SAE 8
lbs-ft
N-m
lbs-ft
N-m
1/4"
7/16"
6
8
10
13
14
18
5/16"
3/8"
1/2"
9/16"
12
23
17
31
19
35
26
47
27
49
37
67
7/16"
1/2"
5/8"
3/4"
36
55
48
75
55
85
75
115
78
120
106
163
9/16"
5/8"
13/16"
15/16"
78
110
106
149
121
170
164
230
171
240
232
325
3/4"
7/8"
1-1/8"
1-5/16"
192
306
261
416
297
474
403
642
420
669
569
907
1"
1-1/2"
467
634
722
979
1020
1383
METRIC SERIES
TORQUE
CHART
A
A
Metric Bolt Head
Identification
8.8
Metric
Grade 8.8
10.9
Metric
Grade 10.9
COARSE THREAD
FINE THREAD
MARKING ON HEAD
MARKING ON HEAD
A
Diameter &
Thread Pitch
(Millimeters)
Wrench
Size
N-m
lbs-ft
N-m
lbs-ft
N-m
lbs-ft
N-m
lbs-ft
Diameter &
Thread Pitch
(Millimeters)
6 x 1.0
8 x 1.25
10 mm
13 mm
8
20
6
15
11
27
8
20
8
21
6
16
11
29
8
22
6 x 1.0
8 x 1.0
10 x 1.5
12 x 1.75
16 mm
18 mm
39
68
29
50
54
94
40
70
41
75
30
55
57
103
42
76
10 x 1.25
12 x 1.25
14 x 2.0
16 x 2.0
21 mm
24 mm
109
169
80
125
151
234
111
173
118
181
87
133
163
250
120
184
14 x 1.5
16 x 1.5
18 x 2.5
20 x 2.5
27 mm
30 mm
234
330
172
244
323
457
239
337
263
367
194
270
363
507
268
374
18 x 1.5
20 x 1.5
22 x 2.5
24 x 3.0
34 mm
36 mm
451
571
332
421
623
790
460
583
495
623
365
459
684
861
505
635
22 x 1.5
24 x 2.0
30 x 3.0
46 mm
1175
867
1626
1199
1258
928
1740
1283
30 x 2.0
Typical Washer
Installations
Bolt
Metric 8.8
Lock Washer
Metric 10.9
Metric 8.8
Metric 10.9
Flat Washer
8/9/00
24 Appendix
Bolt Torque & Size Charts (Rev. 10/10/2005)
BOLT SIZE CHART
NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.
SAE Bolt Thread Sizes
5/16
3/8
1/2
IN
MM
5/8
3/4
7/8
1
2
3
4
5
6
7
25
50
75
100
125
150
175
Metric Bolt Thread Sizes
8MM
10MM
12MM
14MM
16MM
18MM
ABBREVIATIONS
AG ............................................................. Agriculture
ATF...............................Automatic Transmission Fluid
BSPP .......................... British Standard Pipe Parallel
BSPTM...............British Standard Pipe Tapered Male
CV .................................................. Constant Velocity
CCW ............................................ Counter-Clockwise
CW ............................................................. Clockwise
F..................................................................... Female
GA ................................................................... Gauge
GR (5, etc.) ......................................... Grade (5, etc.)
HHCS .......................................Hex Head Cap Screw
HT ......................................................... Heat-Treated
JIC............... Joint Industry Council 37° Degree Flare
LH ...............................................................Left Hand
LT ......................................................................... Left
m ....................................................................... Meter
mm ..............................................................Millimeter
M ........................................................................ Male
MPa........................................................Mega Pascal
N .................................................................... Newton
Bolt Torque & Size Charts (Rev. 10/10/2005)
NC ....................................................National Coarse
NF......................................................... National Fine
NPSM ...................National Pipe Straight Mechanical
NPT ........................................ National Pipe Tapered
NPT SWF ....... National Pipe Tapered Swivel Female
ORBM ......................................... O-Ring Boss - Male
P .........................................................................Pitch
PBY .................................................... Power-Beyond
psi ........................................ Pounds per Square Inch
PTO ................................................... Power Take Off
QD ..................................................Quick Disconnect
RH ............................................................Right Hand
ROPS.......................... Roll-Over Protective Structure
RPM.......................................Revolutions Per Minute
RT ...................................................................... Right
SAE ........................Society of Automotive Engineers
UNC ....................................................Unified Coarse
UNF ........................................................ Unified Fine
UNS ....................................................Unified Special
Appendix 25
WARRANTY
(Replacement Parts For All Models Except Mow’n MachineTM
Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles)
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and
workmanship for a period of ninety (90) days from the date of delivery of the product to the original
purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a
period of 12 months.
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of
WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This
Warranty does not cover normal wear or tear, or normal maintenance items.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell
or otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser
in any way. There are no third party beneficiaries of this Warranty.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of
charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with
this Warranty. The product must be returned to WOODS with proof of purchase within thirty (30)
days after such defect or noncompliance is discovered or should have been discovered, routed through
the dealer and distributor from whom the purchase was made, transportation charges prepaid.
WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the
product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF
REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF
THIS WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND
WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/
OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising
directly or indirectly from the product, whether such claim is based upon breach of contract, breach
of warranty, negligence, strict liability in tort or any other legal theory. Without limiting the generality
of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or
goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for
labor, supplies, substitute machinery or rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to
obtain materials or manufacture replacement parts.
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company,
including without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized
to alter, modify, or enlarge this Warranty.
Answers to any questions regarding warranty service and locations may be obtained by contacting:
F-8494 (Rev. 6/23/2005)
WARRANTY
(All Models Except Mow’n MachineTM Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles)
Please Enter Information Below and Save for Future Reference.
Date Purchased: ____________________________
From (Dealer): __________________________________________
Model Number: ____________________________
Serial Number: __________________________________________
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set
forth below, the duration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF THE
PRODUCT TO THE ORIGINAL PURCHASER.
All current model loaders and backhoes are warranted for two (2) years from the date of delivery to the original purchaser.
The warranty periods for specific parts or conditions are listed below:
Part or
Condition
Warranted
Gearbox
components
Model Number
Duration (from date of delivery
to the original purchaser)
BW1260, BW1620, BW1800, BW2400
8 years
BW240HD, BW180HD, BW180HB, BW126HB
7 years
BB48X, BB60X, BB72X, BB84X, BB600X, BB720X, BB840X, BB6000X, BB7200X,
6 years
BB8400X, DS1260, DSO1260, DS1440, TS1680, BW126-3, BW180-3, BW240
PHD25, PHD35, PHD65, PHD95, 2162, 3240, DS96, DS120, RCC42, RM550-2,
RM660-2, RM990-3, PRD6000, PRD7200, PRD8400, 7144RD-2, 9180RD-2,
5 years
9204RD-2, S15CD, S20CD, S22CD, S25CD, S27CD, BW180LH
3 years (1 year if used in rental or
RDC54, RD60, RD72, TBW150C
commercial applications)
Blade
spindles
RM550-2, RM660-2, RM990-3, PRD6000, PRD7200, PRD8400, 7144RD-2, 9180RD-2,
3 years
9204RD-2
Rust-through
BB600, BB720, BB840, BB6000, BB7200, BB8400, BW126-3, BW126HB, BW180-3,
BW180HB, BW180HD, BW1260, BW1800, BW240, BW240HD, 2162, 3240, DS1260, 10 years
DSO1260, DS1440, TS1680
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to
improper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been
materially modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized
service center. This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty also does not cover repairs made
with parts other than those obtainable through WOODS.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this product to
a third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty.
WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured by
WOODS. Warranties for these items, if any, are provided separately by their respective manufacturers.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if WOODS,
in its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof
of purchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through the
dealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or
replacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS
WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODS
MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY
OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the
product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal
theory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business,
revenues or goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute
machinery or rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain materials or manufacture
replacement parts.
No agent, representative, dealer, distributor, serviceperson, salesperson, or employee of any company, including without limitation, WOODS,
its authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge
this Warranty. Answers to any questions regarding warranty service and locations may be obtained
Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061 USA
800-319-6637 tel
800-399-6637 fax
www.WoodsEquipment.com
F-3079 (Rev 10/21/2009)
PART NO.
MAN0101
© 2001 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks of Woods
Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual
are the property of their respective companies or mark holders. Specifications subject to change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement