Druckschrift 9987147, 790-2500 MHz Base Station Antennas for

Druckschrift 9987147, 790-2500 MHz Base Station Antennas for
Photo on title page: Selection of products for UMTS networks.
Catalogue Issue 02/04
All data published in previous catalog issues hereby becomes invalid.
We reserve the right to make alterations in accordance with the requirements of our customers,
therefore for binding datas please check valid datasheets!
Please note:
As a result of more stringent legal regulations
and judgements regarding product liability, we are
obliged to point out certain risks that may arise
when products are used under extraordinary
operating conditions.
The mechanical design is based on the environmental
conditions as stipulated in ETS 300 019-1-4, which
include the static mechanical load imposed on an
antenna by wind at maximum velocity.
Extraordinary operating conditions, such as heavy
icing or exceptional dynamic stress (e.g. strain caused
by oscillating support structures), may result in the
breakage of an antenna or even cause it to fall to
the ground.
These facts must be considered during the site planning
process.
The details given in our data sheets have to be
followed carefully when installing the antennas and
accessories.
In addition, please use our information brochure
about mounting configurations.
The installation team must be properly qualified
and also be familiar with the relevant national safety
regulations.
“Quality leads the way”
Being the oldest and largest antenna manufacturer worldwide, we take on every day
the challenge arising from our own motto. One of our basic principles is to look always
for the best solution in order to satisfy our customers.
Our quality assurance system conforms to DIN EN ISO 9001 and applies to the product
range of the company: Antenna systems, communication products as well as active
and passive distribution equipment.
GSM 900
GSM-R
GSM 850
CDMA 800
XPol
VPol
XPol
GSM 1800
GSM 1900
PCS
XXPol Dual-band
VPol
XPol Multi-band
XXPol 2-Multi-band
UMTS
XXPol Dual-band
XXXPol Triple-band
VPol Single-/Multi-band
Omni
VPol
Indoor
VPol
RET
Electrical Accessories
Mechanical Accessories
Remote Electrical Tilt-System
Splitters / Tappers
Filter Products
Clamps, Downtilt Kits, ...
3
4
List of available Catalogues for
Mobile Communication Antennas
and Accessories
790 – 2500 MHz Base Station Antennas
for Mobile Communications
27 – 512 MHz Base Station Antennas
for Mobile Communiations
Ground-to-Air Communication Antennas
Antennas for Trains and Busses
790 – 2500 MHz Filters, Combiners,
Amplifiers for Mobile Communications
450 MHz Filters, Combiners,
Amplifiers for Mobile Communications
80 / 160 MHz Filters, Combiners
Amplifiers for Mobile Communications
The listed catalogues
are also available on CD-ROM
5
Summary of Types
The articles are listed by type number in numerical order.
Type No.
Page
730 ...
Type No.
Page
Type No.
Page
Type No.
Page
734 328
74
737 547
45
739 630
23
730 368
43
734 330
75
737 971
190
739 632
17
730 376
46
734 360
194
737 972
189 …
739 633
18
730 378
48
734 361
194
737 973
189 …
739 634
20
730 380
49
734 362
194
737 974
189 …
739 636
24
730 382
50
734 363
194
737 975
189 …
739 637
24
730 677
43
734 364
194
737 976
190
739 648
26
730 691
44
734 365
194
737 978
189 …
739 649
29
739 650
31
739 655
28
731 ...
731 651
735 ...
186
738 ...
735 147
73
738 187
134
739 658
26
735 727
40
738 192
126
739 660
29
738 440
201
739 662
32
738 445
114
739 664
27
732 ...
732 317
197
736 ...
732 318
197
736 347
127
738 446
114 …
739 665
30
732 319
197
736 349
128
738 449
129 …
739 666
33
732 321
197
736 350
125
738 450
122 …
739 684
19
732 322
197
736 854
47
738 454
136 …
739 685
22
732 327
197
736 855
47
738 546
186 …
739 686
25
732 689
46
736 801
170 ...
738 908
198
739 695
56
732 691
44
736 802
170 ...
739 707
57
732 967
48
736 803
170 ...
739 ...
739 708
57
736 804
170 ...
739 136
72
739 710
58
736 805
170 ...
739 489
83
739 785
133
739 490
53
739 854
45
739 491
53
739 856
50
739 927
52
733 ...
733 677
186
733 678
186
737 ...
733 679
186
737 190
135
739 494
54
733 680
186
737 303
171
739 495
55
733 695
41
737 304
171
739 498
55
741 ...
733 736
41 ...
737 305
171
739 619
16
741 264
54
737 306
171
739 620
16
741 316
60
737 307
171
739 622
17
741 320
61
734 ...
6
734 304
73
737 308
171
739 623
20
741 322
64
734 318
74
737 398
199
739 624
23
741 324
66
Summary of Types
The articles are listed by type number in numerical order.
Type No.
Page
741 326
62
741 327
Type No.
Page
Type No.
Page
Type No.
742 211
84
800 10111
132
K 61 ...
65
742 212
87
800 10137
143
K 61 14 02
40
741 328
67
742 213
90
800 10141
14
K 61 14 03
40 ...
741 336
68
742 215
88
800 10147
130
K 61 14 04
40 ...
741 344
69
742 218
80
800 10173
144
K 61 14 05
40 ...
741 415
116
742 219
81
800 10177
144
K 61 33 5
200
741 572
143
742 222
103
800 10202
34
K 61 33 6
200
741 573
142
742 226
102
800 10203
35
741 622
21
742 233
98
800 10204
36
K 63 ...
741 623
52
742 234
99
800 10207
37
K 63 20 62 1
170
741 717
14
742 235
100
800 10247
85
K 63 20 62 7
170
741 785
15
742 241
111
800 10251
78
K 63 23 60 01
175
741 786
120
742 263
195
K 63 23 60 67
174
741 790
137
742 264
104
850 …
K 63 23 61 07
174
741 794
89
742 265
105
850 10002
186 ...
K 63 23 61 57
174
741 862
131
742 266
106
850 10003
186 ...
741 984
91
742 270
108
850 10006
188
K 73 ...
741 987
92
742 271
109
850 10007
191
K 73 22 67
42
741 988
93
742 272
110
K 73 45 64 7
41
741 989
94
742 290
118
741 990
95
742 351
79
860 10002
164
K 75 ...
742 445
117
860 10003
161
K 75 11 61
123
860 10006
162
K 75 15 64 1
124
860 10007
163
742 ...
860 …
742 033
187
782 …
742 034
187
782 10147
167
860 10017
172
742 035
187
782 10148
167
860 10018
172
742 036
187
782 10149
167
860 10019
172
742 047
70
782 10253
168
860 10020
173
742 113
196
782 10254
168
860 10021
173
742 149
141
782 10255
168
860 10022
173
742 151
63
782 10256
168
860 10023
175
742 192
115
860 10026
162
742 196
86
800 …
860 10030
165
742 210
82
800 10046
860 10031
166
119
Page
7
Antenna Designs:
Antenna Families
Harmony of Design and Technology
Omni
A-Panel
C-Panel
F-Panel
Eurocell Panel
8
Antenna Designs:
Antenna Families
Distinguishing features
Design
Small size and elegant design are the distinguishing features of Kathrein’s
antenna families.
Radome
The radomes cover the internal antenna components. Fiberglass material
guarantees optimum performance with regards to stability, stiffness, UV
resistance, painting and best weather protection.
Environmental influences
The design of Kathrein antennas is based on fundamental engineering
knowledge and also on decades of practical experience, during which the
various constructions and materials used have proved their outstanding
reliability.
Environmental conditions
Kathrein cellular antennas are designed to operate under the environmental
conditions as described in ETS 300 019-1-4 class 4.1 E.
The antennas exceed this standard with regards to the following items:
– Low temperature:
–55 °C
– High temperature (dry): +60 °C
Large variety of
half-power beam width,
gain values,
electrical downtilt
According to the antenna type selected, customer can choose from different
half-power beam widths. Gain values up to 22.5 dBi and electrical
downtilts up to 15° for panel antennas are available. Downtilts are either
fixed or adjustable or even controlled by remote electrical tilt system (RET).
Low intermodulation
After many years of experience in the construction of antennas and after
products (typically –150 dBc) intensive research into the effects of intermodulation, we have been able to
optimize the material and technology used for antennas (the given value
refers to 3rd order products measured with 2 carriers of 20 W each).
Multi-band design
Depending on antenna family broad-band, multi-band, dual-band and
triple-band versions can be offered. Therefore the varity of antennas used
can be kept to a minimum.
Excellent grounding
The antennas are DC grounded according EN 50083-1.
Multi-functional
installation hardware
Depending on the type, the antennas are equipped with up to 3 fixing
points. Panels can be wall mounted without any additional hardware. For
mast mounting, stainless steel brackets and mechanical downtilt kits are
available. To assist the installation technicians in aligning the panels, an
azimuth adjustment tool can be supplied (see Mechanical Accessories).
9
Directional Antenna Designs:
Special Directional Antennas
For Particular Applications
The distinguishing features of these special versions,
e.g. parabolic panels or log. periodic antennas, are:
Antennas for
– tunnel use
– very small half-power beam width (high gain)
– railway use
– high sidelobe suppression
– micro cells (street use)
– also Dual-band and Multi-band versions
– high gain link for repeaters
– bidirectional horizontal pattern.
LogPer
ParPanel
BiDir
10
Downtilting of Antennas:
Downtilt Possibilities
Mechanical downtilt
For further technical information please see “Mechanical Accessories”,
pages 189 and 197.
Electrical downtilt
Description of the interface (protective cap removed):
1
1
2
2
➀ Adjustment wheel with
twist-lock function.
➁ Downtilt spindle with integrated scale.
➀ Thread for fixing of the
protective cap or the RCU
(Remote Control Unit).
➁ Gearwheel for RCU-power
drive.
To set the downtilt angle
exactly, you must look horizontally at the scale. The
lower edge of the gearwheel
must be used for alignment
purposes.
Manual adjustment procedure: (General example)
max.° – 0°
0° – max.°
Remove protective cap.
Set downtilt angle by rotating
the adjustment wheel.
Screw on the protective cap
again.
For antennas without RET, the interface looks
different. In this case you just have to rotate the
adjustment wheel in order to set the downtilt.
Remote Electrical Tilt (RET) For further technical information please see “RET”, page 150...
11
Kathrein Antennas
Product Description (Type)
XXPol A-Panel 870–960/1710–1880 C 65°/ 60° 17/18dBi 2°–8°T/2°T
Polarization(s):
(X) Dual +45°/ –45°
(V) Vertical
Antenna Family
Frequency Range(s)
Integrated Combiner
Horizontal
Half-power Beam Width(s)
Gain Value(s)
Variable / Fixed Electrical Tilt(s)
12
GSM 900
XPol
Summary – Directional Antennas
Dual Polarization + 45°/ –45°
GSM 900 / GSM-R / GSM 850 / CDMA 800
Dual Polarization + 45°/ –45°
Type
Type No.
Height
[mm]
741 717
800 10141
741 785
656
1296
2580
XPol A-Panel
XPol A-Panel
XPol A-Panel
870–960
806–960
870–960
30°
30°
30°
15.5dBi
18.5dBi
21dBi
XPol A-Panel
806–960
65°
9dBi
739 619
XPol A-Panel
806–960
65°
12.5dBi
739 620
XPol A-Panel
XPol A-Panel
XPol A-Panel
XPol A-Panel
806–960
806–960
806–960
806–960
65°
65°
65°
65°
15.5dBi
15dBi
15dBi
15dBi
6°T
12°T
0°–14°T
739
739
739
739
XPol A-Panel
XPol A-Panel
XPol A-Panel
XPol A-Panel
806–960
806–960
824–960
824–960
65°
65°
65°
65°
17dBi
17dBi
17dBi
16.5dBi
6°T
9°T
0°–10°T
XPol A-Panel
XPol A-Panel
XPol A-Panel
XPol A-Panel
XPol A-Panel
870–960
806–960
806–960
806–960
806–960
65°
65°
65°
65°
65°
18dBi
18dBi
18dBi
18dBi
17.5dBi
6°T
9°T
0°–7°T
XPol A-Panel
XPol A-Panel
XPol A-Panel
806–960
806–960
824–960
90°
90°
88°
13.5dBi
13.5dBi
13.5dBi
XPol A-Panel
XPol A-Panel
XPol A-Panel
XPol A-Panel
870–960
806–960
806–960
806–960
90°
88°
88°
88°
XPol A-Panel
XPol A-Panel
XPol A-Panel
806–960
806–960
806–960
88°
88°
88°
Connector
position
Page
bottom
bottom
bottom
14
14
15
256
bottom or top
16
656
bottom or top
16
622
632
633
684
1296
1296
1296
1296
bottom or top
bottom
bottom
bottom
17
17
18
19
739
739
741
739
623
634
622
685
1936
1936
1936
1996
bottom or top
bottom
bottom
bottom
20
20
21
22
739
739
739
739
739
630
624
636
637
686
2580
2580
2580
2580
2580
bottom or top
bottom or top
bottom
bottom
bottom
23
23
24
24
25
6°T
0°–14°T
739 648
739 658
739 664
1296
1296
1296
bottom or top
bottom
bottom
26
26
27
15.5dBi
15.5dBi
15.5dBi
15dBi
6°T
0°–10°T
739
739
739
739
655
649
660
665
1936
1936
1936
1996
bottom or top
bottom or top
bottom
bottom
28
29
29
30
17dBi
17dBi
16dBi
6°T
0°–7°T
739 650
739 662
739 666
2580
2580
2580
bottom or top
bottom
bottom
31
32
33
1294
1934
2254
1294
bottom
bottom
bottom
bottom
34
35
36
37
Compact Panel (C-Panel)
XPol
XPol
XPol
XPol
C-Panel
C-Panel
C-Panel
C-Panel
806–960
806–960
806–960
806–960
65°
65°
65°
65°
15.5dBi
17dBi
18dBi
15dBi
6°T
800
800
800
800
10202
10203
10204
10207
New Products
13
A-Panel
Dual Polarization
Half-power Beam Width
800/900
X
30°
XPol A-Panel 870–960 30° 15.5dBi
Type No.
741 717
Frequency range
870 – 960 MHz
Polarization
+45°, –45°
Gain
2 x 15.5 dBi
30°
Horizontal:
Vertical:
30°
27°
Front-to-back ratio, copolar
> 30 dB
Isolation
> 30 dB
Impedance
50 Ω
VSWR
< 1.5
3
dB
10
Half-power beam width
Copolar +45°/ –45°
0
Horizontal Pattern
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
500 W (at 50 °C ambient temperature)
27°
2 x 7-16 female
Connector position
10
Bottom
3
Weight
dB
Input
13 kg
0
Wind load (at 150 km/h)
Frontal / Lateral / Rearside:
330 N / 60 N / 470 N
Max. wind velocity
200 km/h
Height/width/depth
656 / 560 / 116 mm
Vertical Pattern
800/900
–45°
800/900
+45°
7-16
7-16
XPol A-Panel 806–960 30° 18.5dBi
800 10141
Frequency range
806–960
880 – 960 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 18 dBi
2 x 18.5 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
31°
15°
Horizontal:
Vertical:
Front-to-back ratio, copolar
> 25 dB
> 29 dB
Isolation
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
29°
14°
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
500 W (at 50 °C ambient temperature)
Input
Connector position
Weight
Wind load (at 150 km/h)
10
3
0
Horizontal Pattern
14°
10
2 x 7-16 female
Bottom
22 kg
Frontal / Lateral / Rearside:
680 N / 130 N / 970 N
Max. wind velocity
200 km/h
Height/width/depth
1296 / 560 / 116 mm
14
29°
dB
806 – 894 MHz
3
dB
Type No.
0
Vertical Pattern
Mounting accessories are not included in the scope of delivery (see page 185)
XPol
A-Panel
Dual Polarization
Half-power Beam Width
870 – 960
X
30°
XPol A-Panel 870–960 30° 21dBi
Type No.
741 785
Frequency range
870 – 960 MHz
Polarization
+45°, –45°
Gain
2 x 21 dBi
30°
Front-to-back ratio, copolar
> 30 dB
Isolation
> 30 dB
Impedance
50 Ω
VSWR
< 1.5
30°
7°
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
400 W (at 50 °C ambient temperature)
Input
Connector position
2 x 7-16 female
3
0
Horizontal Pattern
7°
10
Bottom
3
Weight
dB
Horizontal:
Vertical:
dB
10
Half-power beam width
Copolar +45°/ –45°
40 kg
0
Wind load (at 150 km/h)
Frontal / Lateral / Rearside:
1460 N / 280 N / 2090 N
Max. wind velocity
200 km/h
Height/width/depth
2580 / 560 / 116 mm
Mounting accessories are not included in the scope of delivery (see page 185)
Vertical Pattern
870–960
–45°
870–960
+45°
7-16
7-16
15
806 – 960
X
65°
XPol A-Panel 806–960 65° 9dBi
739 619
Frequency range
806 – 880 MHz
880 – 960 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 8.5 dBi
2 x 9 dBi
Horizontal:
Vertical:
Front-to-back ratio, copolar
Cross polar ratio
Maindirection
Sector
0°
±60°
70°
70°
Horizontal:
Vertical:
10
65°
68°
> 27 dB
> 27 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
Isolation
0
Horizontal Pattern
> 30 dB
Impedance
50 Ω
VSWR
< 1.5
68°
10
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
350 W (at 50 °C ambient temperature)
3
Input
2 x 7-16 female
Connector position
0
Vertical Pattern
Bottom or top
Weight
Wind load (at 150 km/h)
3
dB
Half-power beam width
Copolar +45°/ –45°
65°
125°
806–960
dB
Type No.
3 kg
Frontal / Lateral / Rearside:
40 N / 25 N / 90 N
Max. wind velocity
200 km/h
Height/width/depth
256 / 262 / 116 mm
806–960
–45°
806–960
+45°
7-16
7-16
XPol A-Panel 806–960 65° 12.5dBi
739 620
Frequency range
120°
806–960
806 – 880 MHz
880 – 960 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 12 dBi
2 x 12.5 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
68°
29°
Horizontal:
Vertical:
65°
27°
65°
10
3
dB
Type No.
0
Front-to-back ratio, copolar
> 30 dB
Isolation
> 30 dB
Impedance
50 Ω
VSWR
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
500 W (at 50 °C ambient temperature)
Input
Connector position
Weight
Wind load (at 150 km/h)
27°
10
2 x 7-16 female
Bottom or top
6 kg
Frontal / Lateral / Rearside:
110 N / 60 N / 240 N
Max. wind velocity
200 km/h
Height/width/depth
656 / 262 / 116 mm
16
Horizontal Pattern
3
dB
XPol
A-Panel
Dual Polarization
Half-power Beam Width
0
Vertical Pattern
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
XPol
A-Panel
Dual Polarization
Half-power Beam Width
806 – 960
X
65°
XPol A-Panel 806–960 65° 15.5dBi
739 622
Frequency range
806 – 880 MHz
880 – 960 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 15 dBi
2 x 15.5 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
65°
120°
806–960
68°
16°
Horizontal:
Vertical:
65°
15°
10
3
dB
Type No.
0
Front-to-back ratio, copolar
> 30 dB
Isolation
> 30 dB
Horizontal Pattern
50 Ω
Impedance
VSWR
< 1.4
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
600 W (at 50 °C ambient temperature)
Connector position
3
Bottom or top
Weight
Wind load (at 150 km/h)
10
2 x 7-16 female
dB
Input
15°
0
11 kg
Vertical Pattern
Frontal / Lateral / Rearside:
230 N / 130 N / 500 N
Max. wind velocity
200 km/h
Height/width/depth
1296 / 262 / 116 mm
806–960
–45°
806–960
+45°
7-16
7-16
XPol A-Panel 806–960 65° 15dBi 6°T
739 632
Frequency range
120°
806–960
806 – 880 MHz
880 – 960 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 14.5 dBi
2 x 15 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
68°
16°
Horizontal:
Vertical:
65°
15°
65°
10
3
dB
Type No.
0
6°, fixed
6°, fixed
Sidelobe suppression for
first sidelobe above horizon
≥ 14 dB
≥ 16 dB
Front-to-back ratio, copolar
> 28 dB
> 30 dB
Isolation
> 30 dB
> 32 dB
Impedance
50 Ω
50 Ω
VSWR
< 1.5
< 1.3
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
600 W (at 50 °C ambient temperature)
Input
Connector position
Weight
Wind load (at 150 km/h)
Horizontal Pattern
15°
10
3
2 x 7-16 female
dB
Electrical tilt
0
Vertical Pattern
6° electrical downtilt
Bottom
11 kg
Frontal / Lateral / Rearside:
230 N / 130 N / 500 N
Max. wind velocity
200 km/h
Height/width/depth
1296 / 262 / 116 mm
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
17
806 – 960
X
65°
XPol A-Panel 806–960 65° 15dBi 12°T
739 633
Frequency range
806 – 880 MHz
880 – 960 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 14.5 dBi
2 x 15 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
68°
17°
65°
120°
806–960
Horizontal:
Vertical:
65°
16°
10
3
dB
Type No.
0
Electrical tilt
Sidelobe suppression for
first sidelobe above horizon
12°, fixed
12°, fixed
≥ 14 dB
≥ 16 dB
Front-to-back ratio, copolar
> 28 dB
> 30 dB
Isolation
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
VSWR
< 1.5
< 1.3
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
600 W (at 50 °C ambient temperature)
Input
Connector position
Weight
Wind load (at 150 km/h)
16°
10
3
2 x 7-16 female
0
Vertical Pattern
12° electrical downtilt
Bottom
8 kg
Frontal / Lateral / Rearside:
230 N / 130 N / 500 N
Max. wind velocity
200 km/h
Height/width/depth
1296 / 262 / 116 mm
18
Horizontal Pattern
dB
XPol
A-Panel
Dual Polarization
Half-power Beam Width
806–960
–45°
806–960
+45°
7-16
7-16
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
XPol
A-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electr. Downtilt
806 – 960
X
65°
0°– 14°
set by hand or by optional RCU (Remote Control Unit)
XPol A-Panel 806–960 65° 15dBi 0°–14°T
739 684
Type No.
Frequency range
Polarization
Gain
Half-power beam width
Copolar +45°/ –45°
806 – 960
824 – 894 MHz
880 – 960 MHz
+45°, –45°
+45°, –45°
+45°, –45°
14.5 dBi
14.7 dBi
Horizontal:
Vertical:
Electrical tilt
continuously adjustable
70°
16°
Front-to-back ratio, copolar
0°
±60°
Isolation, between ports
15 dBi
Horizontal: 68°
Vertical: 15.5°
0°– 14°
Sidelobe suppression for
sector 0°–30° above horizon
Cross polar ratio
Maindirection
Sector
806 – 866 MHz
Horizontal:
Vertical:
0°– 14°
65°
15°
0°– 14°
14 dB
15 dB
15 dB
> 25 dB
> 25 dB
> 25 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
> 30 dB
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
400 W (at 50 °C ambient temperature)
880 – 960 MHz: +45°/ –45° Polarization
125°
65°
15°
10
3
dB
3
dB
10
0
0
Horizontal Pattern
Vertical Pattern
0°– 14° electrical downtilt
824 – 894 MHz: +45°/ –45° Polarization
130°
806 – 960
–45°
806 – 960
+45°
7-16
7-16
68°
15.5°
3
Input
dB
dB
3
Mechanical specifications
10
10
0
Horizontal Pattern
Vertical Pattern
0°– 14° electrical downtilt
806 – 866 MHz: +45°/ –45° Polarization
Adjustment
mechanism
Bottom
1x, Position bottom
continuously adjustable
Weight
Wind load
135°
2 x 7-16 female
Connector position
0
70°
14 kg
Frontal:
Lateral:
Rearside:
230 N (at 150 km/h)
130 N (at 150 km/h)
500 N (at 150 km/h)
16°
Max. wind velocity
dB
3
0
Horizontal Pattern
3
dB
10
10
200 km/h
Packing size
1562 x 287 x 165 mm
Height/width/depth
1296 / 262 / 116 mm
0
Vertical Pattern
0°– 14° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
19
806 – 960
X
65°
XPol A-Panel 806–960 65° 17dBi
739 623
806 – 894 MHz
880 – 960 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 16.5 dBi
2 x 17 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
68°
10°
Horizontal: 65°
Vertical:
9.5°
Sidelobe suppression for
first sidelobe above horizon
≥ 15 dB
Front-to-back ratio, copolar
> 30 dB
Isolation
> 30 dB
Impedance
50 Ω
VSWR
< 1.5
9.5°
Max. power per input
600 W (at 50 °C ambient temperature)
10
2 x 7-16 female
3
0
Bottom or top
Vertical Pattern
12 kg
first null-fill below horizon
better or equal –25 dB
below maximum gain
Weight
Wind load (at 150 km/h)
3
0
< –150 dBc
Connector position
10
Horizontal Pattern
Intermodulation IM3
(2 x 43 dBm carrier)
Input
65°
120°
806–960
dB
Frequency range
dB
Type No.
Frontal / Lateral / Rearside:
330 N / 200 N / 770 N
Max. wind velocity
200 km/h
Height/width/depth
1936 / 262 / 116 mm
806–960
–45°
806–960
+45°
7-16
7-16
XPol A-Panel 806–960 65° 17dBi 6°T
739 634
Type No.
Frequency range
806–960
880 – 960 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 16.5 dBi
2 x 17 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
68°
10°
Horizontal: 65°
Vertical:
9.5°
10
3
Electrical tilt
6°, fixed
6°, fixed
Sidelobe suppression for
first sidelobe above horizon
≥ 14 dB
≥18 dB
Front-to-back ratio, copolar
> 30 dB
> 30 dB
Isolation
> 32 dB
> 32 dB
50 Ω
50 Ω
VSWR
< 1.5
< –150 dBc
Max. power per input
600 W (at 50 °C ambient temperature)
Weight
Wind load (at 150 km/h)
9.5°
10
7-16 female
Bottom
12 kg
3
0
Vertical Pattern
6° electrical downtilt
Frontal / Lateral / Rearside:
350 N / 200 N / 770 N
Max. wind velocity
200 km/h
Height/width/depth
1936 / 262 / 116 mm
20
0
< 1.3
Intermodulation IM3
(2 x 43 dBm carrier)
Connector position
65°
Horizontal Pattern
Impedance
Input
120°
dB
806 – 894 MHz
dB
XPol
A-Panel
Dual Polarization
Half-power Beam Width
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
XPol
A-Panel
Dual Polarization
Half-power Beam Width
824 – 960
X
65°
XPol A-Panel 824–960 65° 17dBi 9°T
741 622
Frequency range
824 – 880 MHz
880 – 960 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 16.5 dBi
2 x 17 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
68°
10°
65°
120°
824–960
Horizontal: 65°
Vertical:
9.5°
10
3
dB
Type No.
0
9°, fixed
9°, fixed
Sidelobe suppression for
first sidelobe above horizon
≥ 14 dB
≥16 dB
Front-to-back ratio, copolar
> 30 dB
> 30 dB
Isolation
> 32 dB
> 32 dB
Impedance
50 Ω
50 Ω
VSWR
< 1.5
< 1.3
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
500 W (at 50 °C ambient temperature)
Input
Connector position
Weight
Wind load (at 150 km/h)
Horizontal Pattern
9.5°
10
3
2 x 7-16 female
dB
Electrical tilt
0
Vertical Pattern
9° electrical downtilt
Bottom
12 kg
Frontal / Lateral / Rearside:
330 N / 200 N / 770 N
Max. wind velocity
200 km/h
Height/width/depth
1936 / 262 / 116 mm
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
824–960
–45°
824–960
+45°
7-16
7-16
21
806 – 960
X
65°
0° – 10°
set by hand or by optional RCU (Remote Control Unit)
XPol A-Panel 806–960 65° 16.5dBi 0°–10°T
739 685
Type No.
Frequency range
Polarization
Gain
806 – 866 MHz
806–960
824 – 894 MHz
880 – 960 MHz
+45°, –45°
+45°, –45
+45°, –45°
2 x 16 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
Electrical tilt
continuously adjustable
2 x 16 dBi
70°
10°
Horizontal:
Vertical:
0.5° – 10°
2 x 16.5 dBi
68°
10°
Horizontal:
Vertical:
0.5° – 10°
65°
9.5°
0.5° – 10°
Sidelobe suppression for
0° ... 3° ... 6° ... 10°T
0° ... 3° ... 6° ... 10°T
0° ... 3° ... 6° ... 10°T
first sidelobe above horizon 15 ... 14 ... 12 ... 12 dB 15 ... 15 ... 15 ... 14 dB 17 ... 17 ... 17 ... 17 dB
sector 0°– 30° above horizon
12 dB
13 dB
15 dB
Front-to-back ratio, copolar
Cross polar ratio
Maindirection
Sector
0°
±60°
Isolation, between ports
> 25 dB
> 25 dB
> 25 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
> 30 dB
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
400 W (at 50 °C ambient temperature)
880 – 960 MHz: +45°/ –45° Polarization
125°
65°
9.5°
dB
3
3
dB
10
10
0
0
Horizontal Pattern
Vertical Pattern
0.5°– 10° electrical downtilt
824 – 894 MHz: +45°/ –45° Polarization
130°
806 – 960
–45°
806 – 960
+45°
7-16
7-16
68°
10°
3
Input
dB
dB
3
Mechanical specifications
10
10
0
Horizontal Pattern
Vertical Pattern
0.5°– 10° electrical downtilt
806 – 866 MHz: +45°/ –45° Polarization
Adjustment
mechanism
Bottom
1x, Position bottom
continuously adjustable
Weight
Wind load
135°
2 x 7-16 female
Connector position
0
70°
18 kg
Frontal:
Lateral:
Rearside:
330 N (at 150 km/h)
200 N (at 150 km/h)
770 N (at 150 km/h)
10°
Max. wind velocity
3
3
dB
10
10
dB
XPol
A-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electr. Downtilt
200 km/h
Packing size
2262 x 287 x 165 mm
Height/width/depth
1996 / 262 / 116 mm
0
0
Horizontal Pattern
22
Vertical Pattern
0.5°– 10° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
XPol
A-Panel
Dual Polarization
Half-power Beam Width
800/900
X
65°
XPol A-Panel 870–960 65° 18dBi
Type No.
739 630
Frequency range
870 – 960 MHz
Polarization
+45°, –45°
Gain
2 x 18 dBi
65°
120°
Horizontal:
Vertical:
65°
7°
3
≥ 15 dB
Sidelobe suppression for
first sidelobe above horizon
0
Horizontal Pattern
Front-to-back ratio, copolar
> 30 dB
Isolation
> 32 dB
Impedance
50 Ω
VSWR
< 1.3
7°
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
600 W (at 50 °C ambient temperature)
3
2 x 7-16 female
Connector position
0
Bottom or top
Weight
dB
10
Input
Wind load (at 150 km/h)
dB
10
Half-power beam width
Copolar +45°/ –45°
Vertical Pattern
19 kg
first null-fill below horizon
better or equal –25 dB
below maximum gain
Frontal / Lateral / Rearside:
470 N / 280 N / 1040 N
Max. wind velocity
200 km/h
Height/width/depth
2580 / 262 / 116 mm
800/900
–45°
800/900
+45°
7-16
7-16
XPol A-Panel 806–960 65° 18dBi
739 624
Frequency range
120°
806–960
806 – 880 MHz
880 – 960 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 17.5 dBi
2 x 18 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal: 68°
Vertical:
7.5°
Horizontal:
Vertical:
65°
7°
65°
10
3
dB
Type No.
0
Front-to-back ratio, copolar
> 30 dB
> 30 dB
Isolation
> 30 dB
> 32 dB
Impedance
50 Ω
VSWR
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
600 W (at 50 °C ambient temperature)
Connector position
Weight
Wind load (at 150 km/h)
7°
10
2 x 7-16 female
Bottom or top
19 kg
Frontal / Lateral / Rearside:
470 N / 280 N / 1040 N
Max. wind velocity
200 km/h
Height/width/depth
2580 / 262 / 116 mm
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
3
dB
Input
Horizontal Pattern
0
Vertical Pattern
23
806 – 960
X
65°
XPol A-Panel 806–960 65° 18dBi 6°T
739 636
Type No.
Frequency range
806–960
880 – 960 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 17.5 dBi
2 x 18 dBi
Horizontal: 68°
Vertical:
7.5°
Horizontal:
Vertical:
Electrical tilt
6°, fixed
Sidelobe suppression for
first sidelobe above horizon
≥ 18 dB
Front-to-back ratio, copolar
> 30 dB
Isolation
> 32 dB
3
dB
< 1.3
< –150 dBc
0
500 W (at 50 °C ambient temperature)
Input
Vertical Pattern
6° electrical downtilt
2 x 7-16 female
Connector position
Bottom
Weight
Wind load (at 150 km/h)
0
Horizontal Pattern
10
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power per input
3
7°
50 Ω
Impedance
VSWR
65°
7°
10
dB
806 – 880 MHz
Half-power beam width
Copolar +45°/ –45°
65°
120°
19 kg
Frontal / Lateral / Rearside:
470 N / 280 N / 1040 N
Max. wind velocity
200 km/h
Height/width/depth
2580 / 262 / 116 mm
806–960
–45°
806–960
+45°
7-16
7-16
XPol A-Panel 806–960 65° 18dBi 9°T
739 637
Frequency range
120°
806–960
806 – 870 MHz
870 – 960 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 17.5 dBi
2 x 18 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
65°
7.5°
65°
10
3
dB
Type No.
0
Electrical tilt
9°, fixed
Horizontal Pattern
Sidelobe suppression for
first sidelobe above horizon
better 18 dB below maximum gain
Front-to-back ratio, copolar
> 30 dB
Isolation
> 32 dB
50 Ω
Impedance
VSWR
< 1.5
7.5°
< 1.3
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
500 W (at 50 °C ambient temperature)
Input
Connector position
Weight
Wind load (at 150 km/h)
3
2 x 7-16 female
0
Vertical Pattern
9° electrical downtilt
Bottom
19 kg
Frontal / Lateral / Rearside:
470 N / 280 N / 1040 N
Max. wind velocity
200 km/h
Height/width/depth
2580 / 262 / 116 mm
24
10
dB
XPol
A-Panel
Dual Polarization
Half-power Beam Width
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
XPol
A-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electr. Downtilt
806 – 960
X
65°
0° – 7°
set by hand or by optional RCU (Remote Control Unit)
XPol A-Panel 806–960 65° 17.5dBi 0°–7°T
739 686
Type No.
Frequency range
Polarization
Gain
806 – 866 MHz
806–960
824 – 894 MHz
880 – 960 MHz
+45°, –45°
+45°, –45
+45°, –45°
2 x 17 dBi
2 x 17.2 dBi
Half-power beam width
Copolar +45°/ -45°
Horizontal: 70°
Vertical:
7.9°
Horizontal: 68°
Vertical:
7.7°
Electrical tilt
continuously adjustable
0° – 7°
0° – 7°
2 x 17.5 dBi
Horizontal:
Vertical:
65°
7.5°
0° – 7°
Sidelobe suppression for
0° ... 2° ... 4° ... 7° T
0° ... 2° ... 4° ... 7° T
0° ... 2° ... 4° ... 7° T
first sidelobe above horizon 17 ... 17 ... 17 ... 17 dB 18 ... 18 ... 18 ... 18 dB 18 ... 18 ... 18 ... 18 dB
sector 0°–30° above horizon 14 ... 14 ... 14 ... 14 dB 15 ... 15 ... 15 ... 15 dB 17 ... 17 ... 17 ... 17 dB
Front-to-back ratio, copolar
Cross polar ratio
Maindirection
Sector
0°
±60°
Isolation
> 25 dB
> 25 dB
> 25 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
> 30 dB
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
400 W (at 50 °C ambient temperature)
880 – 960 MHz: +45°/ –45° Polarization
125°
65°
7.5°
dB
3
3
dB
10
10
0
0
Horizontal Pattern
Vertical Pattern
0°– 7° electrical downtilt
824 – 894 MHz: +45°/ –45° Polarization
130°
806 – 960
–45°
806 – 960
+45°
7-16
7-16
68°
7.7°
3
Input
dB
dB
3
Mechanical specifications
10
10
0
Connector position
0
Horizontal Pattern
Vertical Pattern
0°– 7° electrical downtilt
806 – 866 MHz: +45°/ –45° Polarization
Adjustment
mechanism
Weight
Wind load
135°
70°
2 x 7-16 female
Bottom
1x, Position bottom
continuously adjustable
22 kg
Frontal:
470 N (at 150 km/h)
Lateral:
280 N (at 150 km/h)
Rearside: 1040 N (at 150 km/h)
7.9°
Max. wind velocity
dB
3
3
dB
10
10
200 km/h
Packing size
2846 x 287 x 165 mm
Height/width/depth
2580 / 262 / 116 mm
0
0
Horizontal Pattern
Vertical Pattern
0°– 7° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
25
806 – 960
X
90°
XPol A-Panel 806–960 90° 13.5dBi
739 648
90°
170°
806–960
806 – 880 MHz
880 – 960 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 13 dBi
2 x 13.5 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
90°
16°
Horizontal:
Vertical:
Sidelobe suppression for
first sidelobe above horizon
≥ 16 dB
Front-to-back ratio, copolar
> 25 dB
Isolation
> 32 dB
Impedance
50 Ω
VSWR
< 1.5
90°
15°
15°
< –150 dBc
Max. power per input
600 W (at 50 °C ambient temperature)
3
0
Vertical Pattern
Bottom or top
Weight
Wind load (at 150 km/h)
10
2 x 7-16 female
Connector position
0
Horizontal Pattern
Intermodulation IM3
(2 x 43 dBm carrier)
Input
3
dB
Frequency range
dB
Type No.
10 kg
Frontal / Lateral / Rearside:
230 N / 130 N / 500 N
Max. wind velocity
200 km/h
Height/width/depth
1296 / 262 / 116 mm
806–960
–45°
806–960
+45°
7-16
7-16
XPol A-Panel 806–960 90° 13.5dBi 6°T
739 658
Frequency range
90°
170°
806–960
806 – 880 MHz
880 – 960 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 13 dBi
2 x 13.5 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
90°
16°
Horizontal:
Vertical:
Electrical tilt
6°, fixed
Sidelobe suppression for
first sidelobe above horizon
≥ 15 dB
Front-to-back ratio, copolar
> 25 dB
Isolation
> 30 dB
< 1.5
15°
< 1.3
< –150 dBc
Max. power per input
500 W (at 50 °C ambient temperature)
Connector position
Weight
Wind load (at 150 km/h)
10
3
2 x 7-16 female
0
Vertical Pattern
6° electrical downtilt
Bottom
8 kg
Frontal / Lateral / Rearside:
230 N / 130 N / 500 N
Max. wind velocity
200 km/h
Height/width/depth
1296 / 262 / 116 mm
26
0
Horizontal Pattern
Intermodulation IM3
(2 x 43 dBm carrier)
Input
3
50 Ω
Impedance
VSWR
90°
15°
dB
Type No.
dB
XPol
A-Panel
Dual Polarization
Half-power Beam Width
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
XPol
A-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electr. Downtilt
824– 960
X
88°
0°– 14°
set by hand or by optional RCU (Remote Control Unit)
XPol A-Panel 824–960 88° 13.5dBi 0°–14°T
739 664
Type No.
Frequency range
824–960
Polarization
Gain
824 – 894 MHz
880 – 960 MHz
+45°, –45°
+45°, –45°
13.5 dBi
13.5 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal: 85°
Vertical:
15.5°
Electrical tilt
continuously adjustable
0°–14°
Sidelobe suppression for
first sidelobe above horizon
Front-to-back ratio, copolar
Cross polar ratio
Maindirection
Sector
0°
±60°
Isolation
Horizontal:
Vertical:
88°
15°
0°–14°
0° ... 4° ... 8° ... 14° T 0° ... 4° ... 8° ... 14° T
16 ... 16 ... 16 ... 16 dB 15 ... 16 ... 16 ... 16 dB
> 23 dB
> 23 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
> 30 dB
50 Ω
Impedance
VSWR
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
400 W (at 50 °C ambient temperature)
880 – 960 MHz: +45°/ –45° Polarization
88°
170°
15°
824 – 960
–45°
824 – 960
+45°
7-16
7-16
10
3
0
dB
3
dB
10
0
Horizontal Pattern
Vertical Pattern
0°– 14° electrical downtilt
continuously adjustable
Mechanical specifications
Input
2 x 7-16 female
Connector position
824 – 894 MHz: +45°/ –45° Polarization
Adjustment
mechanism
85°
170°
Bottom
1x, Position bottom
continuously adjustable
Weight
15.5°
Wind load
14 kg
Frontal:
Lateral:
Rearside:
230 N (at 150 km/h)
130 N (at 150 km/h)
500 N (at 150 km/h)
10
Max. wind velocity
0
Horizontal Pattern
3
dB
3
dB
10
0
200 km/h
Packing size
1562 x 287 x 165 mm
Height/width/depth
1296 / 262 / 116 mm
Vertical Pattern
0°– 14° electrical downtilt
continuously adjustable
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
27
870 – 960
X
90°
XPol A-Panel 870–960 90° 15.5dBi
739 655
Frequency range
870 – 960 MHz
Polarization
+45°, –45°
Gain
2 x 15.5 dBi
Half-power beam width
Copolar +45°/ –45°
Sidelobe suppression for
first sidelobe above horizon
Horizontal:
Vertical:
90°
10°
≥ 15 dB
90°
170°
3
dB
Type No.
0
Horizontal Pattern
Front-to-back ratio, copolar
> 25 dB
Isolation
> 32 dB
Impedance
50 Ω
VSWR
< 1.3
10°
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
600 W (at 50 °C ambient temperature)
Input
Connector position
Weight
Wind load (at 150 km/h)
10
2 x 7-16 female
Bottom or top
14 kg
Frontal / Lateral / Rearside:
330 N / 200 N / 770 N
Max. wind velocity
200 km/h
Height/width/depth
1936 / 262 / 116 mm
28
3
dB
XPol
A-Panel
Dual Polarization
Half-power Beam Width
0
Vertical Pattern
first null-fill below horizon
better or equal –25 dB
below maximum gain
870–960
–45°
870–960
+45°
7-16
7-16
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
XPol
A-Panel
Dual Polarization
Half-power Beam Width
806 – 960
X
88°
XPol A-Panel 806–960 88° 15.5dBi
739 649
165°
806–960
806 – 894 MHz
880 – 960 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 15 dBi
2 x 15.5 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal: 85°
Vertical:
10.5°
Horizontal:
Vertical:
Sidelobe suppression for
first sidelobe above horizon
≥ 18 dB
Front-to-back ratio, copolar
> 25 dB
Isolation
> 30 dB
Impedance
50 Ω
VSWR
< 1.5
88°
10°
Max. power per input
600 W (at 50 °C ambient temperature)
10
2 x 7-16 female
3
0
Bottom or top
Vertical Pattern
17.1 kg
first null-fill below horizon
better or equal –25 dB
below maximum gain
Weight
Wind load (at 150 km/h)
0
10°
< –150 dBc
Connector position
3
Horizontal Pattern
Intermodulation IM3
(2 x 43 dBm carrier)
Input
10
dB
Frequency range
88°
dB
Type No.
Frontal / Lateral / Rearside:
330 N / 200 N / 770 N
Max. wind velocity
200 km/h
Height/width/depth
1936 / 262 / 116 mm
806–960
–45°
806–960
+45°
7-16
7-16
XPol A-Panel 806–960 88° 15.5dBi 6°T
739 660
Frequency range
88°
165°
806–960
806 – 894 MHz
880 – 960 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 15 dBi
2 x 15.5 dBi
Horizontal: 85°
Vertical:
10.5°
Horizontal:
Vertical:
Electrical tilt
6°, fixed
Sidelobe suppression for
first sidelobe above horizon
≥ 18 dB
Front-to-back ratio, copolar
> 25 dB
Isolation
> 30 dB
< 1.3
10°
< 1.3
< –150 dBc
Max. power per input
600 W (at 50 °C ambient temperature)
Connector position
Weight
Wind load (at 150 km/h)
3
0
Horizontal Pattern
Intermodulation IM3
(2 x 43 dBm carrier)
Input
10
50 Ω
Impedance
VSWR
88°
10°
10
3
2 x 7-16 female
dB
Half-power beam width
Copolar +45°/ –45°
dB
Type No.
0
Vertical Pattern
6° electrical downtilt
Bottom
17 kg
Frontal / Lateral / Rearside:
330 N / 200 N / 770 N
Max. wind velocity
200 km/h
Height/width/depth
1936 / 262 / 116 mm
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
29
806 – 960
X
88°
0° – 10°
set by hand or by optional RCU (Remote Control Unit)
XPol A-Panel 806–960 88° 15dBi 0°–10°T
739 665
Type No.
Frequency range
806 – 866 MHz
806–960
824 – 894 MHz
880 – 960 MHz
+45°, –45°
Polarization
+45°, –45°
+45°, –45
Gain
2 x 15 dBi
2 x 15 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal: 85°
Vertical: 10.5°
Horizontal: 85°
Vertical: 10.2°
Electrical tilt
continuously adjustable
0.5° – 10°
0.5° – 10°
Sidelobe suppression for
first sidelobe above horizon
Front-to-back ratio, copolar
Cross polar ratio
Maindirection
Sector
0°
±60°
Isolation
2 x 15 dBi
Horizontal:
Vertical:
88°
10°
0.5° – 10°
0° ... 4° ... 8° ... 10° T 0° ... 4° ... 8° ... 10° T 0° ... 4° ... 8° ... 10° T
16 ... 16 ... 17 ... 17 dB 16 ... 16 ... 17 ... 17 dB 16 ... 16 ... 18 ... 18 dB
> 25 dB
> 25 dB
> 25 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
> 30 dB
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
400 W (at 50 °C ambient temperature)
880 – 960 MHz: +45°/ –45° Polarization
88°
160°
10°
10
3
0
dB
3
dB
10
0
Horizontal Pattern
Vertical Pattern
0.5°– 10° electrical downtilt
824 – 894 MHz: +45°/ –45° Polarization
806 – 960
–45°
806 – 960
+45°
7-16
7-16
85°
160°
10.2°
Mechanical specifications
10
3
0
Input
dB
3
dB
10
Horizontal Pattern
2 x 7-16 female
Connector position
0
Vertical Pattern
0.5°– 10° electrical downtilt
806 – 866 MHz: +45°/ –45° Polarization
Adjustment
mechanism
Bottom
1x, Position bottom
continuously adjustable
Weight
Wind load
85°
160°
18 kg
Frontal:
Lateral:
Rearside:
330 N (at 150 km/h)
200 N (at 150 km/h)
770 N (at 150 km/h)
10.5°
Max. wind velocity
10
3
0
Horizontal Pattern
30
3
dB
10
dB
XPol
A-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electr. Downtilt
200 km/h
Packing size
2262 x 287 x 165 mm
Height/width/depth
1996 / 262 / 116 mm
0
Vertical Pattern
0.5°– 10° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
XPol
A-Panel
Dual Polarization
Half-power Beam Width
806 – 960
X
88°
XPol A-Panel 806–960 88° 17dBi
739 650
165°
806–960
806 – 894 MHz
880 – 960 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 16.5 dBi
2 x 16.7 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal: 85°
Vertical:
8.5°
Horizontal:
Vertical:
Sidelobe suppression for
first sidelobe above horizon
≥ 18 dB
Front-to-back ratio, copolar
> 25 dB
Isolation
> 30 dB
Impedance
50 Ω
VSWR
< 1.5
88°
8°
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
600 W (at 50 °C ambient temperature)
Input
Connector position
Weight
Wind load (at 150 km/h)
2 x 7-16 female
10
3
dB
Frequency range
88°
0
Horizontal Pattern
8°
10
3
dB
Type No.
0
Bottom or top
Vertical Pattern
22.6 kg
first null-fill below horizon
better or equal –25 dB
below maximum gain
Frontal / Lateral / Rearside:
470 N / 280 N / 1040 N
Max. wind velocity
200 km/h
Height/width/depth
2580 / 262 / 116 mm
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
806–960
–45°
806–960
+45°
7-16
7-16
31
806 – 960
X
88°
6°
XPol A-Panel 806–960 88° 17dBi 6°T
739 662
Type No.
Frequency range
Polarization
Gain
Half-power beam width
Copolar +45°/ –45°
Electrical tilt
806 – 866 MHz
806–960
824 – 894 MHz
880 – 960 MHz
+45°, –45°
+45°, –45
+45°, –45°
2 x 16.3 dBi
2 x 16.5 dBi
Horizontal: 85°
Vertical:
8.3°
Horizontal: 85°
Vertical:
7.9°
6° , fixed
6° , fixed
2 x 16.7 dBi
Horizontal:
Vertical:
16 dB
16 dB
17 dB
Front-to-back ratio, copolar
> 25 dB
> 25 dB
> 25 dB
Isolation
> 32 dB
> 32 dB
> 32 dB
> 23 dB
> 14 dB
> 23 dB
> 14 dB
> 23 dB
> 14 dB
Cross polar ratio
Maindirection
Sector
0°
±60°
88°
7.5°
6° , fixed
Sidelobe suppression for
first sidelobe above horizon
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.3
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
500 W (at 50 °C ambient temperature)
880 – 960 MHz: +45°/ –45° Polarization
88°
165°
7.5°
10
3
0
dB
3
dB
10
0
Horizontal Pattern
Vertical Pattern
6° electrical downtilt
824 – 894 MHz: +45°/ –45° Polarization
806 – 960
–45°
806 – 960
+45°
7-16
7-16
85°
160°
7.9°
10
3
0
dB
3
dB
10
Mechanical specifications
0
Horizontal Pattern
Vertical Pattern
6° electrical downtilt
806 – 866 MHz: +45°/ –45° Polarization
85°
Input
Connector position
Weight
Wind load
160°
8.3°
Max. wind velocity
2 x 7-16 female
Bottom
21.4 kg
Frontal:
470 N (at 150 km/h)
Lateral:
280 N (at 150 km/h)
Rearside: 1040 N (at 150 km/h)
200 km/h
10
3
0
Horizontal Pattern
32
3
dB
10
dB
XPol
A-Panel
Dual Polarization
Half-power Beam Width
Fixed Electrical Downtilt
Packing size
2721 x 302 x 172 mm
Height/width/depth
2580 / 262 / 116 mm
0
Vertical Pattern
6° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
XPol
A-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electr. Downtilt
806 – 960
X
88°
0° – 7°
set by hand or by optional RCU (Remote Control Unit)
XPol A-Panel 806–960 88° 16dBi 0°–7°T
739 666
Type No.
Frequency range
Polarization
Gain
806 – 866 MHz
806–960
824 – 894 MHz
880 – 960 MHz
+45°, –45°
+45°, –45
+45°, –45°
2 x 16 dBi
2 x 16.1 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal: 85°
Vertical:
8.2°
Electrical tilt
continuously adjustable
0° – 7°
Sidelobe suppression for
first sidelobe above horizon
Front-to-back ratio
(180° ± 30°)
Cross polar ratio
Maindirection
Sector
0°
±60°
Isolation
Horizontal:
Vertical:
2 x 16.2 dBi
85°
8°
Horizontal:
Vertical:
0° – 7°
88°
7.5°
0° – 7°
0° ... 2° ... 4° ... 7° T
0° ... 2° ... 4° ... 7° T
0° ... 2° ... 4° ... 7° T
17 ... 17 ... 17 ... 17 dB 17 ... 17 ... 17 ... 17 dB 17 ... 17 ... 17 ... 17 dB
Copolar:
> 25 dB
Total power: > 25 dB
Copolar:
> 25 dB
Total power: > 25 dB
Copolar:
> 25 dB
Total power: > 25 dB
Typically: 25 dB
> 15 dB
Typically: 25 dB
> 15 dB
Typically: 25 dB
> 15 dB
> 30 dB
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
400 W (at 50 °C ambient temperature)
880 – 960 MHz: +45°/ –45° Polarization
88°
160°
7.5°
10
3
0
dB
3
dB
10
0
Horizontal Pattern
Vertical Pattern
0°– 7° electrical downtilt
824 – 894 MHz: +45°/ –45° Polarization
806 – 960
–45°
806 – 960
+45°
7-16
7-16
85°
160°
8°
Mechanical specifications
10
3
0
Input
dB
3
dB
10
Connector position
0
Horizontal Pattern
Vertical Pattern
0°– 7° electrical downtilt
806 – 866 MHz: +45°/ –45° Polarization
Adjustment
mechanism
Weight
Wind load
85°
160°
2 x 7-16 female
Bottom
1x, Position bottom
continuously adjustable
22 kg
Frontal:
470 N (at 150 km/h)
Lateral:
280 N (at 150 km/h)
Rearside: 1040 N (at 150 km/h)
8.2°
Max. wind velocity
10
0
Horizontal Pattern
3
dB
3
dB
10
200 km/h
Packing size
2846 x 287 x 165 mm
Height/width/depth
2580 / 262 / 116 mm
0
Vertical Pattern
0°– 7° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
33
806 – 960
X
65°
0°
XPol C-Panel 806–960 65° 15.5dBi 0°T
800 10202
Type No.
Frequency range
Polarization
Gain
Half-power beam width
Copolar +45°/ –45°
Sidelobe suppression for:
first sidelobe above horizon
sector 0°– 30° above horizon
806 – 866 MHz
806–960
824 – 894 MHz
880 – 960 MHz
+45°, –45°
+45°, –45°
+45°, –45°
2 x 14.7 dBi
2 x 15 dBi
Horizontal: 67°
Vertical:
15.5°
Horizontal: 66°
Vertical:
14.8°
> 15 dB
> 15 dB
> 15 dB
> 15 dB
2 x 15.3 dBi
Horizontal:
Vertical:
> 30 dB
> 30 dB
> 30 dB
Isolation
> 30 dB
> 30 dB
> 30 dB
> 20 dB
> 19 dB
> 11 dB
> 20 dB
> 19 dB
> 11 dB
> 20 dB
> 20 dB
> 11 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.4
< 1.3
Crosspolar ratio
Maindirection
Sector
Sector
0°
±30°
±60°
64°
14°
> 14 dB
> 14 dB
Front-to-back ratio, copolar
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
500 W (at 50 °C ambient temperature)
880 – 960 MHz: +45°/ –45° Polarization
120°
64°
14°
dB
3
3
dB
10
10
0
0
Horizontal Pattern
Vertical Pattern
824 – 894 MHz: +45°/ –45° Polarization
124°
806 – 960
–45°
806 – 960
+45°
7-16
7-16
66°
14.8°
10
3
dB
3
dB
10
0
Mechanical specifications
0
Horizontal Pattern
Vertical Pattern
Input
806 – 866 MHz: +45°/ –45° Polarization
2 x 7-16 female
Connector position
Bottom
Weight
127°
Wind load
67°
15.5°
3
Max. wind velocity
10
3
dB
10
dB
XPol
Compact Panel
Dual Polarization
Half-power Beam Width
Fixed Electrical Downtilt
0
0
Horizontal Pattern
34
6.5 kg
Frontal:
Lateral:
Rearside:
220 N (at 150 km/h)
140 N (at 150 km/h)
490 N (at 150 km/h)
200 km/h
Packing size
1422 x 272 x 160 mm
Height/width/depth
1294 / 259 / 112 mm
Vertical Pattern
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
XPol
Compact Panel
Dual Polarization
Half-power Beam Width
Fixed Electrical Downtilt
806 – 960
X
65°
0°
XPol C-Panel 806–960 65° 17dBi 0°T
800 10203
Type No.
Frequency range
806 – 866 MHz
806–960
824 – 894 MHz
880 – 960 MHz
Polarization
+45°, –45°
+45°, –45°
+45°, –45°
Gain
2 x 16.5 dBi
2 x 16.7 dBi
2 x 17 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal: 68°
Vertical:
10.2°
Horizontal:
Vertical:
66°
10°
Horizontal: 64°
Vertical:
9.3°
Sidelobe suppression for:
first sidelobe above horizon
sector 0°–30° above horizon
> 17 dB
> 15 dB
> 17 dB
> 15 dB
> 17 dB
> 15 dB
Front-to-back ratio, copolar
> 30 dB
> 30 dB
> 30 dB
Isolation
> 30 dB
> 30 dB
> 30 dB
> 20 dB
> 18 dB
> 12 dB
> 20 dB
> 18 dB
> 12 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.4
< 1.3
Cross polar ratio
Maindirection
Sector
Sector
0°
±30°
±60°
> 20 dB
> 18 dB
> 12 dB
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
500 W (at 50 °C ambient temperature)
880 – 960 MHz: +45°/ –45° Polarization
120°
64°
9.3°
dB
3
3
dB
10
10
0
0
Horizontal Pattern
Vertical Pattern
824 – 894 MHz: +45°/ –45° Polarization
127°
66°
806 – 960
–45°
806 – 960
+45°
7-16
7-16
10°
dB
3
3
dB
10
10
Mechanical specifications
0
0
Horizontal Pattern
Input
Vertical Pattern
2 x 7-16 female
Connector position
806 – 866 MHz: +45°/ –45° Polarization
Wind load
130°
68°
10.2°
dB
3
3
dB
10
10
Rearside
Weight
Max. wind velocity
9.5 kg
Frontal:
Lateral:
Rearside:
340 N (at 150 km/h)
220 N (at 150 km/h)
750 N (at 150 km/h)
200 km/h
Packing size
2062 x 272 x 160 mm
Height/width/depth
1934 / 259 / 112 mm
0
0
Horizontal Pattern
Vertical Pattern
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
35
806 – 960
X
65°
0°
XPol C-Panel 806–960 65° 18dBi 0°T
800 10204
Type No.
Frequency range
806–960
824 – 894 MHz
806 – 866 MHz
880 – 960 MHz
Polarization
+45°, –45°
+45°, –45°
+45°, –45°
Gain
2 x 17.4 dBi
2 x 17.6 dBi
2 x 17.8 dBi
Horizontal: 68°
Vertical:
8.5°
Horizontal: 66°
Vertical:
8.3°
Horizontal: 64°
Vertical:
7.8°
Sidelobe suppression for:
first sidelobe above horizon
sector 0°–30° above horizon
> 15 dB
> 15 dB
> 15 dB
> 15 dB
> 15 dB
> 14 dB
Front-to-back ratio, copolar
> 30 dB
> 30 dB
> 30 dB
Isolation
> 30 dB
> 30 dB
> 30 dB
> 18 dB
> 16 dB
> 10 dB
> 19 dB
> 16 dB
> 10 dB
Half-power beam width
Copolar +45°/ –45°
Cross polar ratio
Maindirection
Sector
Sector
0°
±30°
±60°
> 20 dB
> 17 dB
> 11 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.4
< 1.3
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
500 W (at 50 °C ambient temperature)
880 – 960 MHz: +45°/ –45° Polarization
120°
64°
7.8°
dB
3
3
dB
10
10
0
0
Horizontal Pattern
Vertical Pattern
824 – 894 MHz: +45°/ –45° Polarization
127°
806 – 960
–45°
806 – 960
+45°
7-16
7-16
66°
8.3°
10
3
Mechanical specifications
dB
3
dB
10
0
Input
0
Horizontal Pattern
Vertical Pattern
Rearside
Weight
Wind load
130°
2 x 7-16 female
Connector position
806 – 866 MHz: +45°/ –45° Polarization
68°
11 kg
Frontal:
Lateral:
Rearside:
400 N (at 150 km/h)
260 N (at 150 km/h)
890 N (at 150 km/h)
8.5°
Max. wind velocity
3
3
dB
10
10
dB
XPol
Compact Panel
Dual Polarization
Half-power Beam Width
Fixed Electrical Downtilt
200 km/h
Packing size
2382 x 272 x 160 mm
Height/width/depth
2254 / 259 / 112 mm
0
0
Horizontal Pattern
36
Vertical Pattern
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
XPol
Compact Panel
Dual Polarization
Half-power Beam Width
Fixed Electrical Downtilt
806 – 960
X
65°
6°
XPol C-Panel 806–960 65° 15dBi 6°T
800 10207
Type No.
Frequency range
806 – 866 MHz
806–960
824 – 894 MHz
880 – 960 MHz
Polarization
+45°, –45°
+45°, –45°
+45°, –45°
Gain
2 x 14.5 dBi
2 x 14.7 dBi
2 x 15 dBi
Horizontal: 65°
Vertical:
15.7°
Horizontal: 63°
Vertical:
14.6°
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
66°
16°
Electrical tilt
6°, fixed
6°, fixed
6°, fixed
Sidelobe suppression for:
first sidelobe above horizon
sector 0°–30° above horizon
> 14 dB
> 14 dB
> 15 dB
> 15 dB
> 16 dB
> 14 dB
Front-to-back ratio, copolar
> 30 dB
> 30 dB
> 30 dB
Isolation
> 30 dB
> 30 dB
> 30 dB
Tpyically: > 20 dB
Typically: > 10 dB
Typically: > 20 dB
Typically: > 10 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.3
< 1.3
< 1.3
Cross polar ratio
Maindirection
Sector
0°
±60°
Typically: > 20 dB
Typically: > 10 dB
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
500 W (at 50 °C ambient temperature)
880 – 960 MHz: +45°/ –45° Polarization
118°
63°
14.6°
10
3
dB
3
dB
10
0
0
Horizontal Pattern
Vertical Pattern
6° electrical downtilt
824 – 894 MHz: +45°/ –45° Polarization
123°
806 – 960
–45°
806 – 960
+45°
7-16
7-16
65°
15.7°
10
3
dB
3
dB
10
0
Mechanical specifications
0
Horizontal Pattern
Vertical Pattern
6° electrical downtilt
806 – 866 MHz: +45°/ –45° Polarization
Input
Connector position
Bottom
Weight
6.5 kg
Wind load
125°
2 x 7-16 female
66°
Frontal:
Lateral:
Rearside:
220 N (at 150 km/h)
140 N (at 150 km/h)
490 N (at 150 km/h)
16°
Max. wind velocity
dB
3
3
dB
10
10
200 km/h
Packing size
1422 x 272 x 160 mm
Height/width/depth
1294 / 259 / 112 mm
0
0
Horizontal Pattern
Vertical Pattern
6° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
37
38
GSM 900
VPol
Summary – Directional Antennas
Vertical Polarization
GSM 900 / GSM-R / GSM 850 / CDMA 800
Vertical Polarization – 800/900
Type
Type No.
Height
[mm]
Connector
position
Page
735 727
500
bottom
40
VPol Panel
870–960
20°
16.5dBi
VPol ParPanel
870–960
36°
20dBi
K 73 45 64 7
2250
bottom
41
VPol LogPer
790–960
51°
12dBi
K 73 22 67
300
bottom
42
VPol Panel
860–960
65°
9dBi
730 677
264
bottom or top
43
VPol Panel
VPol Panel
870–960
806–960
65°
65°
15.5dBi
15.5dBi
6°T
730 368
732 691
1294
1294
bottom
bottom
43
44
VPol Panel
VPol Panel
870–960
870–960
65°
65°
17dBi
17dBi
9°T
730 691
737 547
1934
1934
rearside
rearside
44
45
VPol Panel
870–960
65°
18dBi
739 854
2254
rearside
45
VPol Panel
VPol Panel
870–960
870–960
65°
65°
18.5dBi
18.5dBi
730 376
732 689
2574
2574
rearside
bottom
46
46
VPol F-Panel
872–960
90°
7.5dBi
736 854
262
bottom or top
47
VPol F-Panel
872–960
90°
10dBi
736 855
502
bottom or top
47
VPol Panel
870–960
90°
15.5dBi
732 967
1934
rearside
48
VPol Panel
870–960
90°
17dBi
730 378
2574
rearside
48
VPol Panel
870–960
105°
16.5dBi
730 380
2574
rearside
49
VPol Panel
870–960
120°
15.5dBi
739 856
2254
rearside
50
VPol Panel
870–960
120°
16dBi
730 382
2574
rearside
50
6°T
Additional versions on request
39
Panel
Vertical Polarization
Half-power Beam Width
870 – 960
V
20°
VPol Panel 870–960 20° 16.5dBi
735 727
Type No.
Input
Frequency range
VSWR
Gain
Impedance
Polarization
Front-to-back-ratio
Half-power Beam Width
Max. power
Weight
Wind load
7-16 female
870 – 960 MHz
< 1.3
16.5 dBi
50 Ω
Vertical
> 24 dB
H-plane: 20°/ E-plane: 33°
500 W (at 50 °C ambient temperature)
10 kg
Frontal:
500 N (at 150 km/h)
Lateral:
110 N (at 150 km/h)
Rearside: 715 N (at 150 km/h)
230 km/h
1062 x 562 x 275 mm
492 / 992 / 190 mm
Max. wind velocity
Packing size
Height/width/depth
Material:
Radiator: Aluminum.
Reflector screen: Weather-proof aluminum.
Radome: Fiberglass, colour: White.
All screws and nuts: Stainless steel.
Ice protection:
Due to the very sturdy antenna construction and
the protection of the radiating system by the
radome, the antenna remains operational even
under icy conditions.
Grounding:
All metal parts of the antenna as well as
the inner conductor are DC grounded.
Accessories (order separately)
Type No.
K
K
K
K
61
61
61
61
14
14
14
14
Description
02
03
04
05
2
2
2
2
clamps
clamps
clamps
clamps
Remarks
Mast: 60 – 115 mm diameter
Mast: 115 – 210 mm diameter
Mast: 210 – 380 mm diameter
Mast: 380 – 521 mm diameter
33°
20°
10
0
Horizontal Pattern
40
3
dB
dB
3
10
0
Vertical Pattern
K 61 14 03
Parabolic Panel
Vertical Polarization
Half-power Beam Width
870 – 960
V
VPol
36°
VPol ParPanel 870–960 36° 20dBi
K 73 45 64 7
Type No.
Input
Frequency range
VSWR
Gain
Impedance
Polarization
Front-to-back ratio
Half-power Beam Width
Max. power
Weight
Wind load
7-16 female
870 – 960 MHz
< 1.3
20 dBi
50 Ω
Vertical
> 30 dB
H-plane: 36°/ E-plane: 8°
500 W (at 50 °C ambient temperature)
30 kg
Frontal:
950 N (at 150 km/h)
Lateral:
600 N (at 150 km/h)
Rearside: 950 N (at 150 km/h)
200 km/h
2420 x 640 x 465 mm
2250 / 591 / 406 mm
Max. wind velocity
Packing size
Height/width/depth
Material:
Radiator: Weather-proof aluminum.
Reflector screen: Weather-proof aluminum.
Radome: Fiberglass, colour: Grey.
All screws and nuts: Stainless steel.
Ice protection:
Due to the very sturdy antenna construction and
the protection of the radiating system by the
radome, the antenna remains operational even
under icy conditions.
Grounding:
All metal parts of the antenna are DC grounded.
The inner conductor is coupled capacitively.
2360
2300
2250
429
Accessories (order separately)
733 736
K 61 14 03
K 61 14 04
K 61 14 05
733 695
2
2
2
2
1
clamps
clamps
clamps
clamps
downtilt kit
Remarks
Mast: 50 – 125 mm diameter
Mast: 115 – 210 mm diameter
Mast: 210 – 380 mm diameter
Mast: 380 – 521 mm diameter
Downtilt angle: 0° – 10°
Use the downtilt kit together
with 2 clamps suitable for
the mast diameter.
∅11
∅13
140
Description
591
Type No.
406
36°
8°
10
3
0
Horizontal Pattern
3
dB
dB
10
0
Vertical Pattern
K 61 14 03
41
790 – 960
V
51°
VPol LogPer 790–960 51° 12dBi
K 73 22 67
Type No.
Input
Frequency range
VSWR
Gain
Impedance
Polarization
Side-lobe supression
Front-to-back ratio
Half-power Beam Width
Max. power
Weight
Wind load
7-16 female
790 – 960 MHz
< 1.4
12 dBi
50 Ω
Vertical
> 25 dB
> 30 dB
H-plane: 51°/ E-plane: 45°
500 W (at 50 °C ambient temperature)
6.3 kg
Frontal:
20 N (at 150 km/h)
Lateral:
260 N (at 150 km/h)
Rearside:
30 N (at 150 km/h)
200 km/h
1000 x 360 x 175 mm
300 / 155 / 785 mm
Max. wind velocity
Packing size
Height/width/depth
Material:
Radiator: Weather-proof aluminum.
Reflector screen: Weather-proof aluminum.
Radome: Fiberglass, colour: Grey.
All screws and nuts: Stainless steel.
Mounting:
The antenna can be mounted on tubular mast
with a diameter of 30 – 70 mm with supplied
clamps.
Ice protection:
Due to the very sturdy antenna construction and
the protection of the radiating system by the
radome, the antenna remains operational even
under icy conditions.
Grounding:
All metal parts of the antenna as well as
the inner conductor are DC grounded.
51°
3
10
0
Horizontal Pattern
42
45°
3
dB
10
dB
VPol
Logarithmic periodic
Vertical Polarization
Half-power Beam Width
0
Vertical Pattern
Eurocell Panel
Vertical Polarization
Half-power Beam Width
900
V
VPol
65°
VPol Panel 860–960 65° 9dBi
Type No.
730 677
Frequency range
860 – 960 MHz
Polarization
65°
120°
Vertical
Gain
9 dBi
> 25 dB (890 – 960 MHz)
> 20 dB (860 – 890 MHz)
Impedance
50 Ω
VSWR
< 1.3
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power
0
Horizontal Pattern
< –150 dBc
70°
350 W (at 50 °C ambient temperature)
Input
N female
Connector position
10
Bottom or top
Weight
Wind load (at 150 km/h)
3
1.2 kg
Frontal / Lateral / Rearside:
40 N / 25 N / 90 N
Max. wind velocity
230 km/h
Height/width/depth
264 / 258 / 103 mm
3
dB
Front-to-back ratio
H-plane: 65°
E-plane: 70°
dB
10
Half-power beam width
0
Vertical Pattern
VPol Panel 870–960 65° 15.5dBi
Type No.
730 368
Frequency range
870 – 960 MHz
Polarization
Gain
120°
65°
Vertical
15.5 dBI
> 25 dB
Impedance
50 Ω
VSWR
< 1.3
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power
Input
Connector position
Weight
3
0
Horizontal Pattern
< –150 dBc
500 W (at 50 °C ambient temperature)
13°
7-16 female
Bottom
10
6 kg
3
Wind load (at 150 km/h)
Frontal / Lateral / Rearside:
220 N / 140 N / 490 N
Max. wind velocity
200 km/h
Height/width/depth
1294 / 258 / 103 mm
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
dB
Front-to-back ratio
H-plane: 65°
E-plane: 13°
dB
10
Half-power beam width
0
Vertical Pattern
43
800/900
V
65°
VPol Panel 806–960 65° 15.5dBi 6°T
Type No.
732 691
Frequency range
806 – 960 MHz
Polarization
Vertical
Gain
15.5 dBi
120°
65°
H-plane: 65°
E-plane: 13°
Electrical downtilt
6°, fixed
Front-to-back ratio
> 25 dB
Impedance
50 Ω
VSWR
< 1.3
Intermodulation IM3
(2 x 43 dBm carrier)
0
Horizontal Pattern
< –150 dBc
13°
500 W (at 50 °C ambient temperature)
Input
7-16 female
Connector position
10
Bottom
3
Weight
6 kg
Wind load (at 150 km/h)
Frontal / Lateral / Rearside:
220 N / 140 N / 490 N
Max. wind velocity
200 km/h
Height/width/depth
1294 / 258 / 103 mm
dB
Max. power
3
dB
10
Half-power beam width
0
Vertical Pattern
6° electrical downtilt
VPol Panel 870–960 65° 17dBi
Type No.
730 691
Frequency range
870 – 960 MHz
Polarization
Gain
120°
65°
Vertical
17 dBi
Front-to-back ratio
H-plane: 65°
E-plane: 8.5°
> 25 dB
Impedance
50 Ω
VSWR
< 1.3
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power
3
dB
10
Half-power beam width
0
Horizontal Pattern
< –150 dBc
500 W (at 50 °C ambient temperature)
8.5°
Input
Connector position
Weight
7-16 female
Rearside
10
9 kg
3
Wind load (at 150 km/h)
Frontal / Lateral / Rearside:
340 N / 220 N / 750 N
Max. wind velocity
200 km/h
Height/width/depth
1934 / 258 / 103 mm
44
dB
VPol
Eurocell Panel
Vertical Polarization
Half-power Beam Width
0
Vertical Pattern
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
Eurocell Panel
Vertical Polarization
Half-power Beam Width
870 – 960
V
VPol
65°
VPol Panel 870–960 65° 17dBi 9°T
Type No.
737 547
Frequency range
870 – 960 MHz
Polarization
Vertical
Gain
17 dBi
120°
65°
H-plane: 65°
E-plane: 8.5°
Electrical downtilt
9°, fixed
Front-to-back ratio
> 25 dB
Impedance
50 Ω
VSWR
< 1.3
Intermodulation IM3
(2 x 43 dBm carrier)
0
Horizontal Pattern
< –150 dBc
9°
500 W (at 50 °C ambient temperature)
Input
7-16 female
Connector position
10
Rearside
3
Weight
9 kg
Wind load (at 150 km/h)
Frontal / Lateral / Rearside:
340 N / 220 N / 750 N
Max. wind velocity
200 km/h
Height/width/depth
1934 / 258 / 103 mm
dB
Max. power
3
dB
10
Half-power beam width
0
Vertical Pattern
9° electrical downtilt
VPol Panel 870–960 65° 18dBi
Type No.
739 854
Frequency range
870 – 960 MHz
Polarization
Gain
120°
65°
Vertical
18 dBi
Front-to-back ratio
H-plane: 65°
E-plane: 7.5°
> 25 dB
Impedance
50 Ω
VSWR
< 1.3
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power
3
dB
10
Half-power beam width
0
Horizontal Pattern
< –150 dBc
400 W (at 50 °C ambient temperature)
7.5°
Connector position
Weight
7-16 female
Rearside
10
10.5 kg
3
Wind load (at 150 km/h)
Frontal / Lateral / Rearside:
400 N / 260 N / 890 N
Max. wind velocity
180 km/h
Height/width/depth
2254 / 258 / 103 mm
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
dB
Input
0
Vertical Pattern
45
870 – 960
V
65°
VPol Panel 870–960 65° 18.5dBi
Type No.
730 376
Frequency range
870 – 960 MHz
Polarization
Vertical
Gain
18.5 dBi
120°
65°
H-plane: 65°
E-plane: 6.5°
Front-to-back ratio
> 25 dB
50 Ω
Impedance
VSWR
0
Horizontal Pattern
< 1.3
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power
3
dB
10
Half-power beam width
< –150 dBc
500 W (at 50 °C ambient temperature)
6.5°
7-16 female
Connector position
Rearside
Weight
10
12 kg
3
Wind load (at 150 km/h)
Frontal / Lateral / Rearside:
460 N / 300 N / 1020 N
Max. wind velocity
200 km/h
Height/width/depth
2574 / 258 / 103 mm
dB
Input
0
Vertical Pattern
VPol Panel 870–960 65° 18.5dBi 6°T
Type No.
732 689
Frequency range
870 – 960 MHz
Polarization
Gain
120°
65°
Vertical
18.5 dBi
Electrical downtilt
Front-to-back ratio
Impedance
VSWR
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power
Input
Connector position
H-plane: 65°
E-plane: 6.5°
6°, fixed
> 25 dB
3
0
Horizontal Pattern
50 Ω
< 1.3
< –150 dBc
6.5°
500 W (at 50 °C ambient temperature)
7-16 female
10
Rearside
3
Weight
dB
10
Half-power beam width
dB
VPol
Eurocell Panel
Vertical Polarization
Half-power Beam Width
12 kg
0
Wind load (at 150 km/h)
Frontal / Lateral / Rearside:
460 N / 300 N / 1020 N
Max. wind velocity
200 km/h
Height/width/depth
2574 / 258 / 103 mm
46
Vertical Pattern
6° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
F-Panel
Vertical Polarization
Half-power Beam Width
872 – 960
V
VPol
90°
VPol F-Panel 872–960 90° 7.5dBi
736 854
Frequency range
872 – 960 MHz
Polarization
Vertical
Gain
7.5 dBi
Half-power beam width
H-plane: 90°
E-plane: 70°
Front-to-back ratio
> 20 dB
50 Ω
Impedance
VSWR
180°
10
3
0
Horizontal Pattern
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –140 dBc
70°
350 W (at 50 °C ambient temperature)
Input
N female
Connector position
Bottom or top
Weight
10
1.5 kg
3
Wind load (at 150 km/h)
Frontal / Lateral / Rearside:
45 N / 20 N / 60 N (at 150 km/h)
Max. wind velocity
200 km/h
Height/width/depth
262 / 155 / 49 mm
dB
Max. power
90°
dB
Type No.
0
Vertical Pattern
VPol F-Panel 872–960 90° 10dBi
Polarization
Gain
Half-power beam width
Front-to-back ratio
872 – 960 MHz
Vertical
10 dBi
H-plane: 90°
E-plane: 36°
> 20 dB
Impedance
50 Ω
VSWR
< 1.4
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power
Input
Connector position
Weight
Wind load (at 150 km/h)
90°
180°
10
3
dB
Frequency range
736 855
0
Horizontal Pattern
< –150 dBc
400 W (at 50 °C ambient temperature)
36°
7-16 female
Bottom or top
2.3 kg
Frontal / Lateral / Rearside:
90 N / 40 N / 110 N
Max. wind velocity
200 km/h
Height/width/depth
502 / 155 / 49 mm
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
10
3
dB
Type No.
0
Vertical Pattern
47
870 – 960
V
90°
VPol Panel 870–960 90° 15.5dBi
732 967
Frequency range
870 – 960 MHz
Polarization
Vertical
Gain
15.5 dBi
Half-power beam width
H-plane: 90°
E-plane: 8.5°
Front-to-back ratio
> 23 dB
50 Ω
Impedance
VSWR
180°
10
3
0
Horizontal Pattern
< 1.3
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power
90°
dB
Type No.
< –150 dBc
500 W (at 50 °C ambient temperature)
8.5°
7-16 female
Connector position
Rearside
Weight
10
9 kg
3
Wind load (at 150 km/h)
Frontal / Lateral / Rearside:
340 N / 220 N / 750 N (at 150 km/h)
Max. wind velocity
200 km/h
Height/width/depth
1934 / 258 / 103 mm
dB
Input
0
Vertical Pattern
VPol Panel 870–960 90° 17dBi
Frequency range
Polarization
Gain
Half-power beam width
Front-to-back ratio
730 378
870 – 960 MHz
Vertical
17 dBi
H-plane: 90°
E-plane: 6.5°
> 23 dB
Impedance
50 Ω
VSWR
< 1.3
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power
90°
180°
10
3
dB
Type No.
0
Horizontal Pattern
< –150 dBc
500 W (at 50 °C ambient temperature)
6.5°
Input
Connector position
Weight
7-16 female
Rearside
10
12 kg
3
Wind load (at 150 km/h)
Frontal / Lateral / Rearside:
460 N / 300 N / 1020 N
Max. wind velocity
200 km/h
Height/width/depth
2574 / 258 / 103 mm
48
dB
VPol
Eurocell Panel
Vertical Polarization
Half-power Beam Width
0
Vertical Pattern
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
Eurocell Panel
Vertical Polarization
Half-power Beam Width
870 – 960
V
VPol
105°
VPol Panel 870–960 105° 16.5dBi
730 380
Frequency range
870 – 960 MHz
Polarization
Vertical
Gain
16.5 dBi
Half-power beam width
Front-to-back ratio
Impedance
VSWR
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power
H-plane: 105°
E-plane: 6.5°
> 22 dB
50 Ω
105°
195°
3
dB
Type No.
0
Horizontal Pattern
< 1.3
< –150 dBc
500 W (at 50 °C ambient temperature)
6.5°
Connector position
Weight
7-16 female
Rearside
10
12 kg
3
Wind load (at 150 km/h)
Frontal / Lateral / Rearside:
460 N / 300 N / 1020 N
Max. wind velocity
200 km/h
Height/width/depth
2574 / 258 / 103 mm
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
dB
Input
0
Vertical Pattern
49
870 – 960
V
120°
VPol Panel 870–960 120° 15.5dBi
Type No.
739 856
Frequency range
870 – 960 MHz
Polarization
Vertical
Gain
15.5 dBi
120°
215°
H-plane: 120°
E-plane: 7.5°
Front-to-back ratio
> 20 dB
50 Ω
Impedance
VSWR
0
Horizontal Pattern
< 1.3
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power
3
dB
10
Half-power beam width
< –150 dBc
400 W (at 50 °C ambient temperature)
7.5°
7-16 female
Connector position
Rearside
Weight
10
10.5 kg
3
Wind load (at 150 km/h)
Frontal / Lateral / Rearside:
400 N / 260 N / 890 N
Max. wind velocity
180 km/h
Height/width/depth
2254 / 258 / 103 mm
dB
Input
0
Vertical Pattern
VPol Panel 870–960 120° 16dBi
Type No.
730 382
Frequency range
870 – 960 MHz
Polarization
Vertical
Gain
16 dBi
120°
215°
Front-to-back ratio
Impedance
VSWR
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power
H-plane: 120°
E-plane: 6.5°
> 20 dB
50 Ω
3
dB
10
Half-power beam width
0
Horizontal Pattern
< 1.3
< –150 dBc
500 W (at 50 °C ambient temperature)
6.5°
Input
Connector position
Weight
7-16 female
Rearside
10
12 kg
3
Wind load (at 150 km/h)
Frontal / Lateral / Rearside:
460 N / 300 N / 1020 N
Max. wind velocity
200 km/h
Height/width/depth
2574 / 258 / 103 mm
50
dB
VPol
Eurocell Panel
Vertical Polarization
Half-power Beam Width
0
Vertical Pattern
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
Dual Polarization + 45°/ –45° – 1800/1900
Type
Type No.
Height
[mm]
Connector
position
Page
XPol F-Panel
1710–1880
33°
19.5dBi
2°T
739 927
982
bottom
52
XPol F-Panel
1710–1880
33°
22dBi
2°T
741 623
1942
bottom
52
XPol F-Panel
XPol F-Panel
XPol F-Panel
1710–1880
1710–1880
1710–1880
65°
65°
65°
15.5dBi
15.5dBi
15dBi
6°T
12°T
739 490
739 491
741 264
662
662
662
bottom or top
bottom
bottom
53
53
54
XPol F-Panel
XPol F-Panel
1710–1880
1710–1990
65°
65°
18dBi
18dBi
2°T
739 494
739 495
1302
1302
bottom or top
bottom
54
55
XPol F-Panel
1710–1990
65°
19.5dBi
2°T
739 498
1942
bottom
55
XPol F-Panel
1710–1990
90°
8dBi
739 695
174
bottom or top
56
XPol F-Panel
XPol F-Panel
1710–1880
1710–1880
90°
90°
16.5dBi
16.5dBi
2°T
6°T
739 707
739 708
1302
1302
bottom
bottom
57
57
XPol F-Panel
1710–1880
90°
17.5dBi
2°T
739 710
1902
bottom
58
51
GSM 1800
XPol
Summary – Directional Antennas
Dual Polarization + 45°/ –45°
GSM 1800 / GSM 1900 / PCS
F-Panel
Dual Polarization
Half-power Beam Width
Fixed Electrical Downtilt
1710–1880
X
33°
2°
XPol F-Panel 1710–1880 33° 19.5dBi 2°T
739 927
Type No.
Frequency range
1710 – 1880 MHz
Polarization
+45°, –45°
Gain
2 x 19.5 dBi
33°
+45°
Horizontal:
Vertical:
–45°
Horizontal:
Vertical:
33°
9°
33°
9°
3
dB
10
Half-power beam width
Copolar
0
Electrical tilt
Horizontal Pattern
above horizon for first sidelobe
better or equal 14 dB below maximum gain
Front-to-back ratio, copolar
> 30 dB
Isolation
> 30 dB
Impedance
50 Ω
VSWR
< 1.5
9°
10
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
200 W (at 50 °C ambient temperature)
3
Input
0
2 x 7-16 female
Vertical Pattern
Bottom
– 2° electrical downtilt
– first null-fill below horizon
better or equal –25 dB
below maximum gain
Connector position
Weight
Wind load (at 150 km/h)
dB
Sidelobe suppression
2°, fixed
7 kg
Frontal / Lateral / Rearside:
260 N / 95 N / 370 N
Max. wind velocity
200 km/h
Height/width/depth
982 / 262 / 59 mm
1710–1880
–45°
1710–1880
+45°
7-16
7-16
XPol F-Panel 1710–1880 33° 22dBi 2°T
741 623
Type No.
Frequency range
1710 – 1880 MHz
Polarization
33°
+45°, –45°
Gain
2 x 22 dBi
+45°
Horizontal:
Vertical:
–45°
Horizontal:
Vertical:
33°
5°
33°
5°
3
dB
10
Half-power beam width
Copolar
0
Sidelobe suppression
2°, fixed
above horizon for first sidelobe
better or equal 14 dB below maximum gain
Front-to-back ratio, copolar
> 30 dB
Isolation
> 30 dB
Impedance
VSWR
50 Ω
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
200 W (at 50 °C ambient temperature)
Input
Connector position
Weight
Wind load (at 150 km/h)
5°
10
3
2 x 7-16 female
0
Vertical Pattern
2° electrical downtilt
Bottom
11 kg
Frontal / Lateral / Rearside:
540 N / 210 N / 770 N
Max. wind velocity
200 km/h
Height/width/depth
1942 / 262 / 59 mm
52
Horizontal Pattern
dB
Electrical tilt
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
F-Panel
Dual Polarization
Half-power Beam Width
1710–1880
X
65°
XPol F-Panel 1710–1880 65° 15.5dBi
Frequency range
739 490
Polarization
+45°, –45°
Gain
2 x 15.5 dBi
65°
120°
1710 – 1880 MHz
XPol
Type No.
Horizontal:
Vertical:
Front-to-back ratio, copolar
> 30 dB
Isolation, between ports
> 30 dB
Impedance
50 Ω
VSWR
< 1.5
65°
13°
3
dB
10
Half-power beam width
Copolar +45°/ –45°
0
Horizontal Pattern
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
200 W (at 50 °C ambient temperature)
13°
Connector position
2 x 7-16 female
10
Bottom or top
3
Weight
dB
Input
3.5 kg
0
Wind load (at 150 km/h)
Frontal / Lateral / Rearside:
150 N / 55 N / 120 N
Max. wind velocity
200 km/h
Height/width/depth
662 / 155 / 49 mm
Vertical Pattern
1710–1880
–45°
1710–1880
+45°
7-16
7-16
XPol F-Panel 1710–1880 65° 15.5dBi 6°T
Type No.
Frequency range
Polarization
Gain
739 491
120°
1710 – 1880 MHz
65°
+45°, –45°
2 x 15.5 dBi
65°
14°
6°, fixed
Front-to-back ratio, copolar
> 30 dB
Isolation, between ports
> 30 dB
Impedance
50 Ω
VSWR
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
200 W (at 50 °C ambient temperature)
Input
3
0
Horizontal Pattern
14°
10
2 x 7-16 female
3
Connector position
Bottom
Weight
3.5 kg
Wind load (at 150 km/h)
Frontal / Lateral / Rearside:
150 N / 55 N / 120 N
Max. wind velocity
200 km/h
Height/width/depth
662 / 155 / 49 mm
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
dB
Electrical tilt
Horizontal:
Vertical:
dB
10
Half-power beam width
Copolar +45°/ –45°
0
Vertical Pattern
6° electrical downtilt
53
F-Panel
Dual Polarization
Half-power Beam Width
1710–1880
X
65°
741 264
Type No.
Frequency range
Polarization
+45°, –45°
Gain
2 x 15 dBi
65°
120°
1710 – 1880 MHz
Horizontal:
Vertical:
Electrical tilt
65°
14°
12°, fixed
Front-to-back ratio, copolar
> 30 dB
Isolation, between ports
> 30 dB
3
0
Horizontal Pattern
50 Ω
Impedance
< 1.4
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
200 W (at 50 °C ambient temperature)
Input
14°
10
2 x 7-16 female
3
Connector position
Bottom
Weight
3.5 kg
dB
VSWR
Wind load (at 150 km/h)
dB
10
Half-power beam width
Copolar +45°/ –45°
0
Frontal / Lateral / Rearside:
150 N / 55 N / 120 N
Max. wind velocity
200 km/h
Height/width/depth
662 / 155 / 49 mm
Vertical Pattern
12° electrical downtilt
1710–1880
–45°
1710–1880
+45°
7-16
7-16
XPol F-Panel 1710–1880 65° 18dBi
Type No.
Frequency range
Polarization
Gain
739 494
120°
1710 – 1880 MHz
65°
+45°, –45°
2 x 18 dBi
Front-to-back ratio, copolar
Isolation, between ports
Impedance
VSWR
Horizontal:
Vertical:
65°
6.5°
> 30 dB
> 30 dB
3
dB
10
Half-power beam width
Copolar +45°/ –45°
0
Horizontal Pattern
50 Ω
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
200 W (at 50 °C ambient temperature)
6.5°
Input
Connector position
2 x 7-16 female
10
Bottom or top
3
Weight
dB
XPol
XPol F-Panel 1710–1880 65° 15dBi 12°T
6 kg
0
Wind load (at 150 km/h)
Frontal / Lateral / Rearside:
310 N / 110 N / 250 N
Max. wind velocity
200 km/h
Height/width/depth
1302 / 155 / 49 mm
54
Vertical Pattern
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
F-Panel
Dual Polarization
Half-power Beam Width
1710–1990
X
65°
XPol F-Panel 1710–1990 65° 18dBi 2°T
Frequency range
739 495
Polarization
+45°, –45°
Gain
2 x 18 dBi
65°
120°
1710 – 1990 MHz
XPol
Type No.
Horizontal:
Vertical:
Electrical tilt
2°, fixed
Sidelobe suppression for
first sidelobe above horizon
≥ 14 dB
Front-to-back ratio, copolar
> 30 dB
Isolation, between ports
> 30 dB
VSWR
0
Horizontal Pattern
50 Ω
< –150 dBc
Max. power per input
200 W (at 50 °C ambient temperature)
Connector position
Weight
Wind load (at 150 km/h)
7°
< 1.4 (1710 – 1880 MHz)
< 1.5 (1880 – 1990 MHz)
Intermodulation IM3
(2 x 43 dBm carrier)
Input
3
10
3
dB
Impedance
65°
7°
dB
10
Half-power beam width
Copolar +45°/ –45°
0
2 x 7-16 female
Vertical Pattern
Bottom
– 2° electrical downtilt
– first null-fill below horizon
better or equal –25 dB
below maximum gain
6 kg
Frontal / Lateral / Rearside:
310 N / 110 N / 250 N
Max. wind velocity
200 km/h
Height/width/depth
1302 / 155 / 49 mm
1710–1990
–45°
1710–1990
+45°
7-16
7-16
XPol F-Panel 1710–1990 65° 19.5dBi 2°T
Frequency range
Polarization
Gain
Half-power beam width
Copolar +45°/ –45°
739 498
120°
1710 – 1990 MHz
65°
+45°, –45°
2 x 19.5 dBi (1880 – 1990 MHz)
2 x 19 dBi (1710 – 1880 MHz)
Horizontal:
Vertical:
65°
5°
10
3
dB
Type No.
0
Electrical tilt
2°, fixed
Sidelobe suppression for
first sidelobe above horizon
≥ 14 dB
Front-to-back ratio, copolar
> 30 dB
Isolation, between ports
> 30 dB
VSWR
50 Ω
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
200 W (at 50 °C ambient temperature)
Input
10
3
2 x 7-16 female
Connector position
Bottom
Weight
8.5 kg
Wind load (at 150 km/h)
5°
dB
Impedance
Horizontal Pattern
0
Vertical Pattern
2° electrical downtilt
Frontal / Lateral / Rearside:
480 N / 180 N / 380 N
Max. wind velocity
200 km/h
Height/width/depth
1942 / 155 / 49 mm
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
55
F-Panel
Dual Polarization
Half-power Beam Width
1710 –1990
X
90°
Frequency range
Polarization
Gain
Half-power beam width
Copolar +45°/ –45°
739 695
1710 – 1990 MHz
+45°, –45°
2 x 8 dBi
Horizontal:
Vertical:
Front-to-back ratio, copolar
> 20 dB
Isolation, between ports
> 30 dB
Impedance
50 Ω
VSWR
< 1.4
90°
55°
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
200 W (at 50 °C ambient temperature)
Input
Connector position
90°
170°
2 x 7-16 female
3
0
Horizontal Pattern
55°
10
Bottom or top
3
Weight
dB
Type No.
dB
XPol
XPol F-Panel 1710–1990 90° 8dBi
3 kg
0
Wind load (at 150 km/h)
Frontal / Lateral / Rearside:
20 N / 15 N / 30 N
Max. wind velocity
200 km/h
Height/width/depth
174 / 155 / 69 mm
56
Vertical Pattern
1710–1990
–45°
1710–1990
+45°
7-16
7-16
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
F-Panel
Dual Polarization
Half-power Beam Width
1710–1880
X
90°
Polarization
+45°, –45°
Gain
2 x 16.5 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
Electrical tilt
2°, fixed
Sidelobe suppression for
first sidelobe above horizon
≥ 14 dB
Front-to-back ratio, copolar
> 27 dB
Isolation, between ports
> 30 dB
Impedance
50 Ω
VSWR
< 1.4
90°
7°
0
7°
< –150 dBc
Max. power per input
200 W (at 50 °C ambient temperature)
Connector position
Weight
Wind load (at 150 km/h)
3
Horizontal Pattern
Intermodulation IM3
(2 x 43 dBm carrier)
Input
90°
170°
1710 – 1880 MHz
dB
Frequency range
739 707
10
3
0
2 x 7-16 female
Bottom
6 kg
Frontal / Lateral / Rearside:
130 N / 110 N / 310 N
Max. wind velocity
200 km/h
Height/width/depth
1302 / 155 / 69 mm
dB
Type No.
XPol
XPol F-Panel 1710–1880 90° 16.5dBi 2°T
Vertical Pattern
– 2° electrical downtilt
– first null-fill below horizon
better or equal –25 dB
below maximum gain
1710–1880
–45°
1710–1880
+45°
7-16
7-16
XPol F-Panel 1710–1880 90° 16.5dBi 6°T
Frequency range
Polarization
Gain
Half-power beam width
Copolar +45°/ –45°
739 708
90°
170°
1710 – 1880 MHz
+45°, –45°
2 x 16.5 dBi
Horizontal:
Vertical:
Electrical tilt
6°, fixed
Sidelobe suppression for
first sidelobe above horizon
≥ 14 dB
Front-to-back ratio, copolar
> 27 dB
Isolation, between ports
> 30 dB
Impedance
50 Ω
VSWR
< 1.4
90°
7°
3
dB
Type No.
0
Horizontal Pattern
7°
< –150 dBc
Max. power per input
200 W (at 50 °C ambient temperature)
Input
Connector position
Weight
Wind load (at 150 km/h)
10
3
0
2 x 7-16 female
Bottom
6 kg
Frontal / Lateral / Rearside:
130 N / 110 N / 310 N
Max. wind velocity
200 km/h
Height/width/depth
1302 / 155 / 69 mm
dB
Intermodulation IM3
(2 x 43 dBm carrier)
Vertical Pattern
– 6° electrical downtilt
– first null-fill below horizon
better or equal –25 dB
below maximum gain
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
57
F-Panel
Dual Polarization
Half-power Beam Width
Fixed Electrical Downtilt
1710–1880
X
90°
2°
Frequency range
739 710
1710 – 1880 MHz
Polarization
+45°, –45°
Gain
2 x 17.5 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
Electrical tilt
2°, fixed
Sidelobe suppression for
first sidelobe above horizon
≥ 14 dB
Front-to-back ratio, copolar
> 25 dB
Isolation, between ports
> 30 dB
Impedance
50 Ω
VSWR
< 1.4
90°
5°
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
200 W (at 50 °C ambient temperature)
Input
Connector position
Weight
Wind load (at 150 km/h)
2 x 7-16 female
Bottom
9 kg
Frontal / Lateral / Rearside:
190 N / 160 N / 470 N
Max. wind velocity
200 km/h
Height/width/depth
1902 / 155 / 69 mm
58
90°
170°
3
dB
Type No.
0
Horizontal Pattern
5°
10
3
dB
XPol
XPol F-Panel 1710–1880 90° 17.5dBi 2°T
0
Vertical Pattern
– 2° electrical downtilt
– first null-fill below horizon
better or equal –25 dB
below maximum gain
1710–1880
–45°
1710–1880
+45°
7-16
7-16
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
Summary – Directional Antennas
Dual-band
GSM 900 / GSM 1800 / GSM 1900 / PCS
Dual-band 800/900 1800/2000 – Dual Polarization + 45°/ –45°
Type No.
Height
[mm]
Page
XXPol A-Panel
870–960/1710–1880
C
65°/65°
12.5/13dBi
741 316
656
60
XXPol A-Panel
XXPol A-Panel
XXPol A-Panel
870–960/1710–1880
870–960/1710–1880
824–960/1710–1880
C
65°/60°
65°/60°
65°/63°
15/16.5dBi
15/17dBi
14.5/16.5dBi
741 320
741 326
742 151
1296
1296
1296
61
62
63
XXPol A-Panel
XXPol A-Panel
870–960/1710–1880
870–960/1710–1880
C
65°/60°
65°/60°
17/18dBi
17/18.5dBi
741 322
741 327
1936
1936
64
65
XXPol A-Panel
XXPol A-Panel
870–960/1710–1880
870–960/1710–1880
C
65°/60°
65°/60°
18/19dBi
18/19.5dBi
741 324
741 328
2580
2580
66
67
XXPol A-Panel
XXPol A-Panel
XXPol A-Panel
870–960/1710–1880
870–960/1710–1880
870–960/1710–1880
C
65°/60°
65°/60°
65°/ 60°
17.5/17.5dBi
17.5/18dBi
17/18dBi
741 336
741 344
742 047
2580
2580
2580
68
69
70
C
C
0°–10°T/2°T
6°T
6°T
2°–8°T/2°T
GSM 1800
XXPol
Type
Connector position: Bottom
59
Dual-band A-Panel
Dual Polarization
Half-power Beam Width
Integrated Combiner
870 – 960
1710 –1880
X
X
65°
65°
C
XXPol A-Panel 870–960/1710–1880 C 65°/ 65° 12.5/13dBi
741 316
Type No.
Frequency range
870900
–960
870 – 960 MHz
1800
1710–1880
1710 – 1880 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 12.5 dBi
2 x 13 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
65°
28°
Horizontal:
Vertical:
Front-to-back ratio, copolar
> 30 dB
> 30 dB
Isolation, between ports
> 30 dB
> 30 dB
60°
19°
Impedance
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< –150 dBc
< –150 dBc
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power per input
250 W
150 W
(at 50 °C ambient temperature)
Integrated combiner
The insertion loss is included in the given
antenna gain values.
870 – 960 +45°/ –45° Polarization
120°
28°
dB
3
3
870 – 960
+45°
1710 –1880
+45°
C
C
7-16
7-16
dB
10
10
870 – 960
–45°
1710 –1880
–45°
65°
0
0
Horizontal Pattern
Vertical Pattern
Mechanical specifications
Input
1710 –1880 +45°/ –45° Polarization
Connector position*
2 x 7-16 female
Bottom or top
Weight
120°
65°
Wind load
19°
Max. wind velocity
Horizontal Pattern
3
dB
dB
0
60
Frontal:
Lateral:
Rearside:
110 N (at 150 km/h)
60 N (at 150 km/h)
240 N (at 150 km/h)
200 km/h
10
10
3
7 kg
0
Vertical Pattern
Packing size
782 x 287 x 165 mm
Height/width/depth
656 / 262 / 116 mm
* Inverted mounting:
Connector position top: Change drain hole screw.
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
Dual-band A-Panel
Dual Polarization
Half-power Beam Width
Integrated Combiner
870 – 960
1710 –1880
X
X
65°
60°
C
XXPol A-Panel 870–960/1710–1880 C 65°/ 60° 15/16.5dBi
Frequency range
870900
–960
870 – 960 MHz
1800
1710–1880
1710 – 1880 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 15 dBi
2 x 16.5 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
65°
14°
Horizontal:
Vertical:
Front-to-back ratio, copolar
> 30 dB
> 30 dB
Isolation, between ports
> 30 dB
> 30 dB
60°
8°
Impedance
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< –150 dBc
< –150 dBc
Intermodulation IM3
(2 x 43 dBm carrier)
XXPol
741 320
Type No.
Max. power per input
250 W
150 W
(at 50 °C ambient temperature)
Integrated combiner
The insertion loss is included in the given
antenna gain values.
870 – 960 +45°/ –45° Polarization
120°
dB
3
3
1710 –1880
+45°
C
7-16
7-16
dB
10
870 – 960
+45°
C
14°
10
870 – 960
–45°
1710 –1880
–45°
65°
0
0
Horizontal Pattern
Vertical Pattern
Mechanical specifications
Input
1710 –1880 +45°/ –45° Polarization
Connector position*
2 x 7-16 female
Bottom or top
Weight
115°
60°
Wind load
8°
Max. wind velocity
Frontal:
Lateral:
Rearside:
220 N (at 150 km/h)
140 N (at 150 km/h)
490 N (at 150 km/h)
200 km/h
dB
0
Horizontal Pattern
3
dB
10
10
3
13 kg
0
Vertical Pattern
Packing size
1422 x 287 x 165 mm
Height/width/depth
1296 / 262 / 116 mm
* Inverted mounting:
Connector position top: Change drain hole screw.
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
61
Dual-band A-Panel
Dual Polarization
Half-power Beam Width
870 – 960
1710 –1880
X
X
65°
60°
XXPol A-Panel 870–960/1710–1880 65°/ 60° 15/17dBi
741 326
Frequency range
900
870
–960
870 – 960 MHz
1800
1710–1880
1710 – 1880 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 15 dBi
2 x 17 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
Front-to-back ratio, copolar
Isolation, between ports
65°
14°
Horizontal:
Vertical:
> 30 dB
60°
8°
> 30 dB
> 30 dB (GSM 900 – GSM 900)1
> 30 dB (GSM 1800 – GSM 1800)
> 30 dB (GSM 900 – GSM 1800)
Impedance
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< –150 dBc
< –150 dBc
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power per input
400 W
200 W
(at 50 °C ambient temperature)
870 – 960 +45°/ –45° Polarization
120°
65°
1710 –1880
–45°
870 – 960
–45°
870 – 960
+45°
1710 –1880
+45°
7-16
7-16
7-16
7-16
14°
dB
3
3
dB
10
10
0
0
Horizontal Pattern
Vertical Pattern
Mechanical specifications
Input
1710 –1880 +45°/ –45° Polarization
Connector position*
4 x 7-16 female
Bottom or top
Weight
115°
60°
Wind load
8°
Max. wind velocity
0
Horizontal Pattern
62
3
dB
3
13 kg
Frontal:
Lateral:
Rearside:
220 N (at 150 km/h)
140 N (at 150 km/h)
490 N (at 150 km/h)
200 km/h
10
10
dB
XXPol
Type No.
0
Vertical Pattern
Packing size
1422 x 287 x 165 mm
Height/width/depth
1296 / 262 / 116 mm
* Inverted mounting:
Connector position top: Change drain hole screw.
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
Dual-band A-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electr. Downtilt
Integrated Combiner
824 – 960
1710 –1880
X
X
65°
63°
0°–10°
2°
C
XXPol A-Panel 824–960/1710–1880 C 65°/63° 14.5/16.5dBi 0°–10°T/2°T
Frequency range
824–960
824 – 880 MHz 880 – 960 MHz
1710–1880
1710 – 1880 MHz
Polarization
+45°, –45°
+45°, –45°
+45°, –45°
Gain
2 x 14 dBi
2 x 14.5 dBi
2 x 16.5 dBi
Horizontal: 69°
Vertical: 14.5°
Horizontal: 65°
Vertical:
14°
Horizontal: 63°
Vertical:
8.5°
0°–10°
0°–10°
2°
Half-power beam width
Copolar +45°/ –45°
Electrical tilt
Sidelobe suppression for
first sidelobe above horizon
Front-to-back ratio, copolar
Cross polar ratio
Maindirection
Sector
0°
±60°
Isolation, between ports
0° ... 6° ... 10°T 0° ... 6° ... 10°T
16 ... 13 ... 12 dB 17 ... 15 ... 13 dB
16 dB
> 30 dB
> 30 dB
> 27 dB
Typically: 20 dB
> 10 dB
Typically: 20 dB
> 10 dB
Typically: 20 dB
> 10 dB
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< –150 dBc
< –150 dBc
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power per input
XXPol
742 151
Type No.
250 W
150 W
(at 50 °C ambient temperature)
Integrated combiner
The insertion loss is included in the given
antenna gain values.
824 – 960 +45°/ –45° Polarization
130°
1710 –1880
–45°
65°
1710 –1880
+45°
C
7-16
7-16
dB
3
dB
10
10
0
0
Horizontal Pattern
Vertical Pattern
0°–10° electrical downtilt
continuously adjustable
120°
Mechanical specifications
Input
Adjustment
mechanism
8.5°
Max. wind velocity
10
3
dB
dB
10
Horizontal Pattern
Bottom
1x, Position bottom
continuously adjustable
Weight
63°
Wind load
0
2 x 7-16 female
Connector position
1710 –1880 +45°/ –45° Polarization
3
824 – 960
+45°
C
14°
3
824 – 960
–45°
14 kg
Frontal:
Lateral:
Rearside:
230 N (at 150 km/h)
130 N (at 150 km/h)
500 N (at 150 km/h)
200 km/h
Packing size
1422 x 287 x 165 mm
Height/width/depth
1296 / 262 / 116 mm
0
Vertical Pattern
2° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
63
Dual-band A-Panel
Dual Polarization
Half-power Beam Width
Integrated Combiner
870 – 960
1710 –1880
X
X
65°
60°
C
XXPol A-Panel 870–960/1710–1880 C 65°/ 60° 17/18dBi
741 322
Frequency range
870900
–960
870 – 960 MHz
1800
1710–1880
1710 – 1880 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 17 dBi
2 x 18 dBi
Horizontal: 65°
Vertical:
9.5°
Horizontal: 60°
Vertical:
5.5°
> 15 dB
> 15 dB
Half-power beam width
Copolar +45°/ –45°
Sidelobe suppression for
first sidelobe above horizon
Front-to-back ratio, copolar
> 30 dB
> 30 dB
Isolation, between ports
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< –150 dBc
< –150 dBc
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power per input
250 W
150 W
(at 50 °C ambient temperature)
Integrated combiner
The insertion loss is included in the given
antenna gain values.
870 – 960 +45°/ –45° Polarization
120°
65°
9.5°
870 – 960
–45°
1710 –1880
–45°
870 – 960
+45°
1710 –1880
+45°
10
C
C
7-16
7-16
3
dB
3
dB
10
0
0
Horizontal Pattern
Vertical Pattern
Mechanical specifications
Input
1710 –1880 +45°/ –45° Polarization
Connector position*
2 x 7-16 female
Bottom or top
Weight
115°
60°
Wind load
5.5°
Max. wind velocity
0
Horizontal Pattern
64
3
dB
3
19 kg
Frontal:
Lateral:
Rearside:
330 N (at 150 km/h)
200 N (at 150 km/h)
770 N (at 150 km/h)
200 km/h
10
10
dB
XXPol
Type No.
0
Vertical Pattern
Packing size
2057 x 287 x 165 mm
Height/width/depth
1936 / 262 / 116 mm
* Inverted mounting:
Connector position top: Change drain hole screw.
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
Dual-band A-Panel
Dual Polarization
Half-power Beam Width
870 – 960
1710 –1880
X
X
65°
60°
XXPol A-Panel 870–960/1710–1880 65°/ 60° 17/18.5dBi
Frequency range
870900
–960
870 – 960 MHz
1800
1710–1880
1710 – 1880 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 17 dBi
2 x 18.5 dBi
Horizontal: 65°
Vertical:
9.5°
Horizontal: 60°
Vertical:
5.5°
Half-power beam width
Copolar +45°/ –45°
Sidelobe suppression for
first sidelobe above horizon
Front-to-back ratio, copolar
Isolation, between ports
XXPol
741 327
Type No.
> 15 dB
> 30 dB
> 30 dB
> 30 dB (GSM 900 – GSM 900)1
> 30 dB (GSM 1800 – GSM 1800)
> 30 dB (GSM 900 – GSM 1800)
Impedance
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< –150 dBc
< –150 dBc
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power per input
400 W
200 W
(at 50 °C ambient temperature)
870 – 960 +45°/ –45° Polarization
120°
65°
9.5°
1710 –1880
–45°
870 – 960
–45°
870 – 960
+45°
1710 –1880
+45°
7-16
7-16
7-16
7-16
10
3
dB
3
dB
10
0
0
Horizontal Pattern
Vertical Pattern
Mechanical specifications
Input
1710 –1880 +45°/ –45° Polarization
Connector position*
4 x 7-16 female
Bottom or top
Weight
115°
60°
Wind load
5.5°
Max. wind velocity
Frontal:
Lateral:
Rearside:
330 N (at 150 km/h)
200 N (at 150 km/h)
770 N (at 150 km/h)
200 km/h
dB
0
Horizontal Pattern
3
dB
10
10
3
19 kg
0
Vertical Pattern
Packing size
2057 x 287 x 165 mm
Height/width/depth
1936 / 262 / 116 mm
* Inverted mounting:
Connector position top: Change drain hole screw.
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
65
Dual-band A-Panel
Dual Polarization
Half-power Beam Width
Integrated Combiner
870 – 960
1710 –1880
X
X
65°
60°
C
XXPol A-Panel 870–960/1710–1880 C 65°/ 60° 18/19dBi
741 324
Frequency range
870900
–960
870 – 960 MHz
1800
1710–1880
1710 – 1880 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 18 dBi
2 x 19 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
65°
7°
Horizontal:
Vertical:
Front-to-back ratio, copolar
> 30 dB
> 30 dB
Isolation, between ports
> 30 dB
> 30 dB
60°
4°
Impedance
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< –150 dBc
< –150 dBc
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power per input
250 W
150 W
(at 50 °C ambient temperature)
Integrated combiner
The insertion loss is included in the given
antenna gain values.
870 – 960 +45°/ –45° Polarization
120°
65°
7°
870 – 960
–45°
1710 –1880
–45°
10
870 – 960
+45°
1710 –1880
+45°
3
0
0
Horizontal Pattern
C
C
7-16
7-16
dB
3
dB
10
Vertical Pattern
Mechanical specifications
Input
1710 –1880 +45°/ –45° Polarization
Connector position*
Weight
115°
60°
Wind load
4°
Max. wind velocity
0
Horizontal Pattern
66
3
dB
3
2 x 7-16 female
Bottom or top
25 kg
Frontal:
470 N (at 150 km/h)
Lateral:
280 N (at 150 km/h)
Rearside: 1040 N (at 150 km/h)
200 km/h
10
10
dB
XXPol
Type No.
0
Vertical Pattern
Packing size
2692 x 287 x 165 mm
Height/width/depth
2580 / 262 / 116 mm
* Inverted mounting:
Connector position top: Change drain hole screw.
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
Dual-band A-Panel
Dual Polarization
Half-power Beam Width
870 – 960
1710 –1880
X
X
65°
60°
XXPol A-Panel 870–960/1710–1880 65°/ 60° 18/19.5dBi
Frequency range
870900
–960
870 – 960 MHz
1800
1710–1880
1710 – 1880 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 18 dBi
2 x 19.5 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
Front-to-back ratio, copolar
Isolation, between ports
XXPol
741 328
Type No.
65°
7°
Horizontal:
Vertical:
> 30 dB
60°
4°
> 30 dB
> 30 dB (GSM 900 – GSM 900)1
> 30 dB (GSM 1800 – GSM 1800)
> 30 dB (GSM 900 – GSM 1800)
Impedance
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< –150 dBc
< –150 dBc
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power per input
400 W
200 W
(at 50 °C ambient temperature)
870 – 960 +45°/ –45° Polarization
120°
65°
7°
1710 –1880
–45°
870 – 960
–45°
870 – 960
+45°
1710 –1880
+45°
7-16
7-16
7-16
7-16
10
3
dB
3
dB
10
0
0
Horizontal Pattern
Vertical Pattern
Mechanical specifications
Input
1710 –1880 +45°/ –45° Polarization
Connector position*
Weight
115°
60°
Wind load
4°
Max. wind velocity
Bottom or top
25 kg
Frontal:
470 N (at 150 km/h)
Lateral:
280 N (at 150 km/h)
Rearside: 1040 N (at 150 km/h)
200 km/h
dB
0
Horizontal Pattern
3
dB
10
10
3
4 x 7-16 female
0
Vertical Pattern
Packing size
2692 x 287 x 165 mm
Height/width/depth
2580 / 262 / 116 mm
* Inverted mounting:
Connector position top: Change drain hole screw.
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
67
Dual-band A-Panel
Dual Polarization
Half-power Beam Width
Fixed Electrical Downtilt
Integrated Combiner
870 – 960
1710 –1880
X
X
65°
60°
6°
6°
C
XXPol A-Panel 870–960/1710–1880 C 65°/ 60° 17.5/17.5dBi 6°T
741 336
Frequency range
870900
–960
870 – 960 MHz
1800
1710–1880
1710 – 1880 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 17.5 dBi
2 x 17.5 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
65°
7°
Horizontal: 60°
Vertical:
6.5°
Electrical tilt
6°, fixed
6°, fixed
Front-to-back ratio, copolar
> 30 dB
> 30 dB
Isolation, between ports
> 30 dB
> 30 dB
50 Ω
50 Ω
Impedance
VSWR
Intermodulation IM3
(2 x 43 dBm carrier)
< 1.5
< 1.5
< –150 dBc
< –150 dBc
Max. power per input
250 W
150 W
(at 50 °C ambient temperature)
Integrated combiner
The insertion loss is included in the given
antenna gain values.
870 – 960 +45°/ –45° Polarization
120°
65°
7°
3
0
0
Horizontal Pattern
Vertical Pattern
6° electrical downtilt
C
7-16
7-16
Input
Connector position
60°
Weight
6.5°
0
Horizontal Pattern
68
3
dB
3
Wind load
10
10
0
Vertical Pattern
6° electrical downtilt
1710 –1880
+45°
Mechanical specifications
1710 –1880 +45°/ –45° Polarization
115°
870 – 960
+45°
C
dB
dB
3
870 – 960
–45°
1710 –1880
–45°
10
10
dB
XXPol
Type No.
Max. wind velocity
2 x 7-16 female
Bottom
25 kg
Frontal:
470 N (at 150 km/h)
Lateral:
280 N (at 150 km/h)
Rearside: 1040 N (at 150 km/h)
200 km/h
Packing size
2692 x 287 x 165 mm
Height/width/depth
2580 / 262 / 116 mm
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
Dual-band A-Panel
Dual Polarization
Half-power Beam Width
Fixed Electrical Downtilt
870 – 960
1710 –1880
X
X
65°
60°
6°
6°
XXPol A-Panel 870–960/1710–1880 65°/ 60° 17.5/18dBi 6°T
Frequency range
870 –960
870 – 960 MHz
1710–1880
1710 – 1880 MHz
Polarization
+45°, –45°
+45°, –45°
Gain
2 x 17.5 dBi
2 x 18 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
65°
7°
Horizontal: 60°
Vertical:
6.5°
Electrical tilt
6°, fixed
6°, fixed
Front-to-back ratio, copolar
> 30 dB
> 30 dB
Isolation, between ports
XXPol
741 344
Type No.
> 30 dB (GSM 900 – GSM 900)1
> 30 dB (GSM 1800 – GSM 1800)
> 30 dB (GSM 900 – GSM 1800)
50 Ω
Impedance
VSWR
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power per input
50 Ω
< 1.5
< 1.5
< –150 dBc
< –150 dBc
400 W
200 W
(at 50 °C ambient temperature)
870 – 960 +45°/ –45° Polarization
120°
65°
7°
dB
3
3
0
0
Horizontal Pattern
1710 –1880
–45°
870 – 960
–45°
870 – 960
+45°
1710 –1880
+45°
7-16
7-16
7-16
7-16
dB
10
10
Vertical Pattern
6° electrical downtilt
Mechanical specifications
1710 –1880 +45°/ –45° Polarization
Input
115°
Connector position
60°
Weight
6.5°
dB
0
Horizontal Pattern
3
dB
10
10
3
Wind load
0
Vertical Pattern
6° electrical downtilt
Max. wind velocity
4 x 7-16 female
Bottom
25 kg
Frontal:
470 N (at 150 km/h)
Lateral:
280 N (at 150 km/h)
Rearside: 1040 N (at 150 km/h)
200 km/h
Packing size
2692 x 287 x 165 mm
Height/width/depth
2580 / 262 / 116 mm
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
69
Dual-band A-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electr. Downtilt
Integrated Combiner
870 – 960
1710 –1880
X
X
65°
60°
2°– 8°
2°
C
XXPol A-Panel 870–960/1710–1880 C 65°/ 60° 17/18dBi 2°–8°T/2°T
742 047
Frequency range
870900
–960
870 – 960 MHz
Polarization
Gain
Half-power beam width
Copolar +45°/ –45°
1800
1710–1880
1710 – 1880 MHz
+45°, –45°
+45°, –45°
2 x 17 dBi (–0.5 dB)
2 x 18 dBi (–0.5 dB)
Horizontal:
Vertical:
Electrical tilt
65°
7°
Horizontal:
Vertical:
2°– 8°, adjustable
2°, fixed
Sidelobe suppression for
first sidelobe above horizon
2° ... 4° ... 6° ... 8° T
20 ... 18 ... 17 ... 15 dB
2° T
17 dB
Front-to-back ratio, copolar
> 30 dB
> 30 dB
Isolation, between ports
> 30 dB
> 30 dB
50 Ω
50 Ω
Impedance
VSWR
Intermodulation IM3
(2 x 43 dBm carrier)
60°
6°
< 1.5
< 1.5
< –150 dBc
< –150 dBc
Max. power per input
250 W
150 W
(at 50 °C ambient temperature)
Integrated combiner
The insertion loss is included in the given
antenna gain values.
870 – 960 +45°/ –45° Polarization
120°
65°
7°
870 – 960
–45°
1710 –1880
–45°
10
870 – 960
+45°
1710 –1880
+45°
3
0
0
Horizontal Pattern
Vertical Pattern
2°– 8° electrical downtilt
continuously adjustable
C
7-16
7-16
Mechanical specifications
Input
1710 –1880 +45°/ –45° Polarization
120°
C
dB
3
dB
10
Connector position
Adjustment
mechanism
60°
Weight
6°
0
Horizontal Pattern
70
3
dB
3
Wind load
10
10
dB
XXPol
Type No.
0
Vertical Pattern
2° electrical downtilt
Max. wind velocity
2 x 7-16 female
Bottom
1x, Position bottom
continuously adjustable
25 kg
Frontal:
470 N (at 150 km/h)
Lateral:
280 N (at 150 km/h)
Rearside: 1040 N (at 150 km/h)
200 km/h
Packing size
2692 x 287 x 165 mm
Height/width/depth
2580 / 262 / 116 mm
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
Summary – Directional Antennas
Vertical Polarization
GSM 1800 / GSM 1900 / PCS
Vertical Polarization
Type No.
Height
[mm]
Connector
position
Page
VPol F-Panel
1710–1990
33°
22.5dBi
739 136
1942
bottom or top
72
VPol F-Panel
1710–1900
65°
10dBi
734 304
182
bottom or top
73
VPol F-Panel
1710–1900
65°
18dBi
735 147
1302
bottom
73
VPol F-Panel
1710–1900
90°
8dBi
734 318
182
bottom or top
74
VPol F-Panel
1710–1900
90°
16.5dBi
2°T
734 328
1302
bottom
74
VPol F-Panel
1710–1900
90°
17.5dBi
2°T
734 330
1942
bottom
75
2°T
GSM 1800
VPol
Type
Additional versions on request
71
F-Panel
Vertical Polarization
Half-power Beam Width
1710–1990
V
33°
VPol F-Panel 1710–1990 33° 22.5dBi
Frequency range
Polarization
Gain
Half-power beam width
739 136
1710 – 1990 MHz
33°
Vertical
22.5 dBi (1880 – 1990 MHz)
22 dBi (1710 – 1880 MHz)
H-plane: 33°
E-plane: 4.5°
10
3
dB
Type No.
0
> 25 dB
Impedance
50 Ω
VSWR
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power
Input
Connector position
Weight
Wind load (at 150 km/h)
< –150 dBc
4.5°
200 W (at 50 °C ambient temperature)
7-16 female
10
Bottom or top
11 kg
Frontal / Lateral / Rearside:
540 N / 210 N / 770 N
Max. wind velocity
200 km/h
Height/width/depth
1942 / 262 / 59 mm
72
Horizontal Pattern
3
dB
Front-to-back ratio
0
Vertical Pattern
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
F-Panel
Vertical Polarization
Half-power Beam Width
1710–1900
V
65°
VPol F-Panel 1710–1900 65° 10dBi
Type No.
Frequency range
734 304
120°
1710 – 1900 MHz
Polarization
Vertical
Gain
10 dBi
65°
> 25 dB
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power
Input
Connector position
VPol
Horizontal Pattern
< 1.3 (1710 – 1880 MHz)
< 1.5 (1880 – 1900 MHz)
< –150 dBc
55°
200 W (at 50 °C ambient temperature)
7-16 female
10
Bottom or top
Weight
Wind load (at 150 km/h)
0
50 Ω
Impedance
VSWR
3
3
1.3 kg
0
Frontal / Lateral / Rearside:
30 N / 5 N / 40 N
Max. wind velocity
200 km/h
Height/width/depth
182 / 155 / 36 mm
dB
Front-to-back ratio
H-plane: 65°
E-plane: 55°
dB
10
Half-power beam width
Vertical Pattern
VPol F-Panel 1710–1900 65° 18dBi 2°T
Type No.
Frequency range
Polarization
Gain
735 147
120°
1710 – 1900 MHz
65°
Vertical
18 dBi
Side lobe suppression
Front-to-back ratio
Impedance
VSWR
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power
Input
3
2°, fixed
0
Horizontal Pattern
above horizon for first sidelobe
better or equal 14 dB below maximum gain
> 25 dB
50 Ω
< 1.3 (1710 – 1880 MHz)
< 1.5 (1880 – 1900 MHz)
7°
< –150 dBc
10
200 W (at 50 °C ambient temperature)
3
7-16 female
dB
Electrical downtilt
H-plane: 65°
E-plane: 7°
dB
10
Half-power beam width
0
Connector position
Bottom
Vertical Pattern
Weight
4.6 kg
– 2° electrical downtilt
– first null-fill below horizon
better or equal to –25 dB
below maximum gain
Wind load (at 150 km/h)
Frontal / Lateral / Rearside:
260 N / 55 N / 310 N
Max. wind velocity
200 km/h
Height/width/depth
1302 / 155 / 36 mm
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
73
F-Panel
Vertical Polarization
Half-power Beam Width
1710–1900
V
90°
VPol F-Panel 1710–1900 90° 8dBi
Polarization
Gain
Half-power beam width
Front-to-back ratio
VSWR
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power
Input
Connector position
Weight
Wind load (at 150 km/h)
90°
180°
Vertical
8 dBi
H-plane: 90°
E-plane: 55°
> 19 dB
50 Ω
3
0
Horizontal Pattern
< 1.3 (1710 – 1880 MHz)
< 1.5 (1880 – 1900 MHz)
< –150 dBc
55°
200 W (at 50 °C ambient temperature)
7-16 female
10
Bottom or top
1.4 kg
Frontal / Lateral / Rearside:
30 N / 15 N / 40 N (at 150 km/h)
Max. wind velocity
200 km/h
Height/width/depth
182 / 155 / 49 mm
3
0
Vertical Pattern
VPol F-Panel 1710–1900 90° 16.5dBi 2°T
Frequency range
Polarization
Gain
Half-power beam width
Electrical downtilt
Side lobe suppression
Front-to-back ratio
Impedance
VSWR
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power
Input
734 328
1710 – 1900 MHz
90°
180°
Vertical
16.5 dBi
H-plane: 90°
E-plane: 7°
2°, fixed
above horizon for first sidelobe
better or equal 14 dB below maximum gain
3
dB
Type No.
0
Horizontal Pattern
> 23 dB
50 Ω
< 1.3 (1710 – 1880 MHz)
< 1.5 (1880 – 1900 MHz)
< –150 dBc
200 W (at 50 °C ambient temperature)
7-16 female
7°
10
3
dB
VPol
Impedance
1710 – 1900 MHz
dB
Frequency range
734 318
dB
Type No.
0
Connector position
Bottom
Vertical Pattern
Weight
4.6 kg
– 2° electrical downtilt
– first null-fill below horizon
better or equal to –25 dB
below maximum gain
Wind load (at 150 km/h)
Frontal / Lateral / Rearside:
250 N / 110 N / 310 N
Max. wind velocity
200 km/h
Height/width/depth
1302 / 155 / 49 mm
74
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
F-Panel
Vertical Polarization
Half-power Beam Width
Fixed Electrical Downtilt
1710–1900
V
90°
2°
VPol F-Panel 1710–1900 90° 17.5dBi 2°T
Polarization
Vertical
Gain
17.5 dBi
Electrical downtilt
Sidelobe suppression
Front-to-back ratio
Impedance
VSWR
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power
Input
H-plane: 90°
E-plane: 5°
3
2°, fixed
0
Horizontal Pattern
above horizon for first sidelobe
better or equal 14 dB below maximum gain
VPol
Half-power beam width
90°
180°
1710 – 1900 MHz
dB
Frequency range
734 330
> 23 dB
50 Ω
< 1.3 (1710 – 1880 MHz)
< 1.5 (1880 – 1900 MHz)
5°
< –150 dBc
10
200 W (at 50 °C ambient temperature)
3
7-16 female
dB
Type No.
0
Connector position
Bottom
Vertical Pattern
Weight
6.9 kg
– 2° electrical downtilt
– first null-fill below horizon
better or equal to –25 dB
below maximum gain
Wind load (at 150 km/h)
Frontal / Lateral / Rearside:
380 N / 180 N / 480 N
Max. wind velocity
200 km/h
Height/width/depth
1942 / 155 / 49 mm
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
75
76
Summary – Directional Antennas
Dual Polarization + 45°/ –45°
UMTS
Dual Polarization + 45°/ –45° – 1800/1900/2000
Type No.
Page
1046
1302
78
79
1306
1942
80
81
XPol F-Panel
XPol F-Panel
1710–2170
1710–2170
33°
33°
20dBi
21dBi
XPol F-Panel
XPol F-Panel
1710–2170
1710–2170
45°
45°
19.5dBi
21.5dBi
XPol
XPol
XPol
XPol
XPol
XPol
XPol
XPol
XPol
F-Panel
F-Panel
F-Panel
F-Panel
F-Panel
F-Panel
F-Panel
F-Panel
F-Panel
1710–2170
1710–2170
1710–2170
1710–2170
1710–2170
1710–2170
1710–2170
1710–2170
1710–2170
65°
65°
65°
65°
65°
65°
65°
65°
65°
9dBi
12dBi
15.5dBi
15.5dBi
16dBi
18dBi
18dBi
18.5dBi
19.5dBi
0°T 742 210
2°T 739 489
0°–10°T
742 211
0°–12°T 800 10247
0°T 742 196
0°–8°T 742 212
0°–10°T 742 215
2°T 741 794
0°–6°T 742 213
155
342
662
735
735
1302
1302
1302
1942
82
83
84
85
86
87
88
89
90
XPol
XPol
XPol
XPol
XPol
F-Panel
F-Panel
F-Panel
F-Panel
F-Panel
1710–2170
1710–2170
1710–2170
1710–2170
1710–2170
88°
88°
88°
88°
88°
11.5dBi
17dBi
14dBi
17dBi
18dBi
0°T
2°T
0°–10°T
0°–8°T
0°–6°T
342
1302
662
1302
1942
91
92
93
94
95
Connector position: Bottom
0°–10°T 800 10251
0°–8°T 742 351
Height
[mm]
0°–8°T
0°–6°T
742 218
742 219
741
741
741
741
741
984
987
988
989
990
UMTS
XPol
Type
New Products
77
Multi-band F-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electrical Downtilt
1710 –2170
X
33°
0°– 10°
set by hand or by optional RCU (Remote Control Unit)
XPol F-Panel 1710–2170 33° 20dBi 0°–10°T
800 10251
Type No.
Frequency range
1710 – 1880 MHz
1710–2170
1850 – 1990 MHz
Polarization
+45°, –45°
+45°, –45°
+45°, –45°
Gain
2 x 19.5 dBi
2 x 19.8 dBi
2 x 20.0 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
Electrical tilt
continuously adjustable
Sidelobe suppression:
Vertical Pattern – first sidelobe above horizon
Horizontal Pattern
Front-to-back ratio, copolar
(180° ± 30°)
Cross polar ratio
Maindirection
Sector
0°
±30°
Isolation, between ports
36°
9°
1920 – 2170 MHz
Horizontal: 35°
Vertical:
8.5°
Horizontal:
Vertical:
33°
8°
0°– 10°
0°– 10°
0°– 10°
0° ... 5° ... 10°T
15 ... 15 … 15 dB
> 14 dB
0° ... 5° ... 10°T
15 ... 15 ... 15 dB
> 14 dB
0° ... 5° ... 10°T
15 ... 15 ... 15 dB
> 14 dB
> 30 dB
> 30 dB
> 30 dB
Typically: 20 dB
> 10 dB
Typically: 20 dB
> 10 dB
Typically: 20 dB
> 10 dB
> 30 dB
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
300 W (at 50 °C ambient temperature)
1710 – 1880 MHz: +45°/ –45° Polarization
36°
10
3
0
dB
10
dB
3
9°
0
Horizontal Pattern
Vertical Pattern
0°– 10° electrical downtilt
1710 – 2170
–45°
1710 – 2170
+45°
7-16
7-16
1850 – 1990 MHz: +45°/ –45° Polarization
35°
10
Mechanical specifications
10
3
0
Input
dB
dB
3
8,5°
Horizontal Pattern
Vertical Pattern
0°– 10° electrical downtilt
1920 – 2170 MHz: +45°/ –45° Polarization
Adjustment
mechanism
33°
Horizontal Pattern
78
3
dB
dB
10
0
1x, Position bottom
continuously adjustable
10 kg
Frontal:
Lateral:
Rearside:
460 N (at 150 km/h)
90 N (at 150 km/h)
460 N (at 150 km/h)
8°
Max. wind velocity
3
Bottom
Weight
Wind load
10
2 x 7-16 female
Connector position
0
200 km/h
Packing size
1318 x 320 x 92 mm
Height/width/depth
1046 / 299 / 69 mm
0
Vertical Pattern
0°– 10° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
Multi-band F-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electrical Downtilt
1710 –2170
X
33°
0°– 8°
set by hand or by optional RCU (Remote Control Unit)
XPol F-Panel 1710–2170 33° 21dBi 0°–8°T
742 351
Frequency range
1710 – 1880 MHz
1710–2170
1850 – 1990 MHz
Polarization
+45°, –45°
+45°, –45°
+45°, –45°
Gain
2 x 20.2 dBi
2 x 20.5 dBi
2 x 20.7 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal: 36°
Vertical:
7.4°
Horizontal: 35°
Vertical:
7.0°
Horizontal: 33°
Vertical:
6.7°
Electrical tilt
continuously adjustable
0°– 8°
0°– 8°
0°– 8°
Sidelobe suppression:
Vertical Pattern – first sidelobe above horizon
Horizontal Pattern
0° ... 4° ... 8° T
18 ... 17 … 16 dB
> 14 dB
0° ... 4° ... 8° T
18 ... 18 ... 17 dB
> 14 dB
0° ... 4° ... 8° T
18 ... 17 ... 16 dB
> 14 dB
Front-to-back ratio, copolar
> 30 dB
> 30 dB
> 30 dB
Typically: 20 dB
> 10 dB
Typically: 20 dB
> 10 dB
Typically: 20 dB
> 10 dB
> 30 dB
Cross polar ratio
Maindirection
Sector
0°
±30°
Isolation, between ports
1920 – 2170 MHz
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
300 W (at 50 °C ambient temperature)
XPol
Type No.
1710 – 1880 MHz: +45°/ –45° Polarization
36°
10
3
0
dB
10
dB
3
7.4°
0
Horizontal Pattern
Vertical Pattern
0°– 8° electrical downtilt
1710 – 2170
–45°
1710 – 2170
+45°
7-16
7-16
1850 – 1990 MHz: +45°/ –45° Polarization
35°
10
Mechanical specifications
10
3
0
Input
dB
dB
3
7°
Horizontal Pattern
Vertical Pattern
0°– 8° electrical downtilt
1920 – 2170 MHz: +45°/ –45° Polarization
Adjustment
mechanism
33°
6.7°
Max. wind velocity
dB
3
0
Horizontal Pattern
3
dB
10
Bottom
1x, Position bottom
continuously adjustable
Weight
Wind load
10
2 x 7-16 female
Connector position
0
12 kg
Frontal:
Lateral:
Rearside:
570 N (at 150 km/h)
110 N (at 150 km/h)
570 N (at 150 km/h)
200 km/h
Packing size
1574 x 320 x 92 mm
Height/width/depth
1302 / 299 / 69 mm
0
Vertical Pattern
0°– 8° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
79
Multi-band F-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electrical Downtilt
1710 –2170
X
45°
0°– 8°
set by hand or by optional RCU (Remote Control Unit)
XPol F-Panel 1710–2170 45° 19.5dBi 0°–8°T
742 218
Type No.
Frequency range
1710 – 1880 MHz
1710–2170
1850 – 1990 MHz
Polarization
+45°, –45°
+45°, –45°
+45°, –45°
Gain
2 x 19 dBi
2 x 19.5 dBi
2 x 19.6 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal: 47°
Vertical:
7.3°
Electrical tilt
continuously adjustable
0°– 8°
Front-to-back ratio
(180° ± 30°)
Cross polar ratio
Maindirection
Sector
0°
±30°
Isolation, between ports
45°
7°
Horizontal: 44°
Vertical:
6.7°
0°– 8°
0°– 8°
0° ... 2° ... 5° ... 8° T
0° ... 2° ... 5° ... 8° T
0° ... 2° ... 5° ... 8° T
17 ... 17 ... 15 ... 15 dB 18 ... 18 ... 17 ... 17 dB 18 ... 18 ... 15 ... 15 dB
> 18 dB
> 18 dB
> 18 dB
Copolar:
> 27 dB
Total power: > 25 dB
Copolar:
> 30 dB
Total power: > 25 dB
Copolar:
> 27 dB
Total power: > 25 dB
Typically: 18 dB
> 13 dB
Typically: 18 dB
> 13 dB
Typically: 18 dB
> 13 dB
> 30 dB
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
300 W (at 50 °C ambient temperature)
1710 – 1880 MHz: +45°/ –45° Polarization
47°
7.3°
dB
3
3
dB
10
10
0
0
Horizontal Pattern
Vertical Pattern
0°– 8° electrical downtilt
1710 – 2170
–45°
1710 – 2170
+45°
7-16
7-16
1850 – 1990 MHz: +45°/ –45° Polarization
45°
7°
3
0
Input
dB
3
Mechanical specifications
10
dB
10
Horizontal Pattern
2 x 7-16 female
Connector position
0
Vertical Pattern
0°– 8° electrical downtilt
1920 – 2170 MHz: +45°/ –45° Polarization
Adjustment
mechanism
Bottom
1x, Position bottom
continuously adjustable
Weight
Wind load
44°
10.2 kg
Frontal:
Lateral:
Rearside:
165 N (at 150 km/h)
110 N (at 150 km/h)
390 N (at 150 km/h)
6.7°
Max. wind velocity
10
3
0
Horizontal Pattern
80
3
Packing size
dB
10
dB
XPol
Sidelobe suppression:
Vertical Pattern – first sidelobe above horizon
Horizontal Pattern
Horizontal:
Vertical:
1920 – 2170 MHz
Height/width/depth
200 km/h
1604 x 221 x 107 mm
1306 / 199 / 69 mm
0
Vertical Pattern
0°– 8° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
Multi-band F-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electrical Downtilt
1710 –2170
X
45°
0°– 6°
set by hand or by optional RCU (Remote Control Unit)
XPol F-Panel 1710–2170 45° 21.5dBi 0°–6°T
742 219
Type No.
Frequency range
1710 – 1880 MHz
1710–2170
1850 – 1990 MHz
Polarization
+45°, –45°
+45°, –45°
+45°, –45°
Gain
2 x 20.5 dBi
2 x 21 dBi
2 x 21.5 dBi
Horizontal: 45°
Vertical:
4.7°
Horizontal: 43°
Vertical:
4.5°
0°– 6°
0°– 6°
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
Electrical tilt
continuously adjustable
0°– 6°
Front-to-back ratio, copolar
total power
Cross polar ratio
Maindirection
Sector
0°
±60°
Isolation, between ports
0° ... 2° ... 4° ... 6°T
0° ... 2° ... 4° ... 6°T
0° ... 2° ... 4° ... 6°T
17 ... 17 ... 17 ... 17 dB 18 ... 18 ... 18 ... 18 dB 18 ... 18 ... 18 ... 18 dB
> 20 dB
> 20 dB
> 20 dB
> 25 dB
> 25 dB
> 25 dB
> 25 dB
> 25 dB
> 25 dB
Typically: 18 dB
> 10 dB
Typically: 18 dB
> 10 dB
Typically: 18 dB
> 10 dB
> 30 dB
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
300 Watt (at 50 °C ambient temperature)
XPol
Sidelobe suppression:
Vertical Pattern – first sidelobe above horizon
Horizontal Pattern
47°
5°
1920 – 2170 MHz
1710 – 1880 MHz: +45°/ –45° Polarization
47°
5°
3
0
dB
3
10
dB
10
0
Horizontal Pattern
Vertical Pattern
0°– 6° electrical downtilt
1850 – 1990 MHz: +45°/ –45° Polarization
1710 – 2170
–45°
1710 – 2170
+45°
7-16
7-16
45°
4.7°
3
0
Input
dB
3
Mechanical specifications
10
dB
10
Horizontal Pattern
Vertical Pattern
0°– 6° electrical downtilt
1920 – 2170 MHz: +45°/ –45° Polarization
Adjustment
mechanism
43°
4.5°
0
Horizontal Pattern
3
Max. wind velocity
Packing size
dB
dB
3
10
Bottom
1x, Position bottom
continuously adjustable
Weight
Wind load
10
2 x 7-16 female
Connector position
0
Height/width/depth
12 kg
Frontal:
Lateral:
Rearside:
250 N (at 150 km/h)
165 N (at 150 km/h)
580 N (at 150 km/h)
200 km/h
2384 x 221 x 107 mm
1942 / 199 / 69 mm
0
Vertical Pattern
0°– 6° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
81
Multi-band F-Panel
Dual Polarization
Half-power Beam Width
Fixed Electrical Downtilt
1710 –2170
X
65°
0°
XPol F-Panel 1710–2170 65° 9dBi 0°T
742 210
Type No.
Frequency range
Polarization
Gain
1710–2170
1850 – 1990 MHz
1920 – 2170 MHz
+45°, –45°
+45°, –45°
+45°, –45°
2 x 8.5 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
2 x 8.6 dBi
70°
65°
Horizontal:
Vertical:
2 x 8.7 dBi
68°
65°
Horizontal:
Vertical:
65°
63°
Electrical tilt
0°, fixed
0°, fixed
0°, fixed
Front-to-back ratio, copolar
> 25 dB
> 30 dB
> 30 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
Cross polar ratio
Maindirection
Sector
0°
±60°
Isolation, between ports
> 30 dB
50 Ω
Impedance
VSWR
< 1.4
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
150 W (at 50 °C ambient temperature)
1710 – 1880 MHz: +45°/ –45° Polarization
135°
70°
3
dB
dB
3
65°
10
10
0
0
Horizontal Pattern
Vertical Pattern
1850 – 1990 MHz: +45°/ –45° Polarization
130°
68°
1710 – 2170
+45°
7-16
7-16
65°
3
Mechanical specifications
dB
dB
3
1710 – 2170
–45°
10
10
0
Input
0
Horizontal Pattern
Vertical Pattern
Connector position*
2 x 7-16 female
Bottom or top
Weight
1920 – 2170 MHz: +45°/ –45° Polarization
127°
65°
3
Wind load
Max. wind velocity
1.5 kg
Frontal:
Lateral:
Rearside:
20 N (at 150 km/h)
15 N (at 150 km/h)
40 N (at 150 km/h)
200 km/h
Packing size
257 x 172 x 92 mm
Height/width/depth
155 / 155 / 69 mm
* Inverted mounting:
Connector position top: Change drain hole screw.
dB
3
63°
10
10
dB
XPol
1710 – 1880 MHz
0
0
Horizontal Pattern
82
Vertical Pattern
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
Multi-band F-Panel
Dual Polarization
Half-power Beam Width
Fixed Electrical Downtilt
1710 –2170
X
65°
2°
XPol F-Panel 1710–2170 65° 12dBi 2°T
739 489
Frequency range
Polarization
Gain
1710 – 1880 MHz
1710–2170
1850 – 1990 MHz
1920 – 2170 MHz
+45°, –45°
+45°, –45°
+45°, –45°
2 x 11.5 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
2 x 12 dBi
67°
32°
Horizontal:
Vertical:
2 x 12 dBi
65°
30°
Horizontal:
Vertical:
63°
28°
Electrical tilt
3°, fixed
2°, fixed
0°, fixed
Front-to-back ratio, copolar
> 30 dB
> 30 dB
> 27 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
Cross polar ratio
Maindirection
Sector
0°
±60°
Isolation, between ports
XPol
Type No.
> 30 dB
50 Ω
Impedance
VSWR
< 1.4
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
150 W (at 50 °C ambient temperature)
1710 – 1880 MHz: +45°/ –45° Polarization
125°
67°
32°
10
3
dB
3
dB
10
0
0
Horizontal Pattern
Vertical Pattern
3° electrical downtilt
1850 – 1990 MHz: +45°/ –45° Polarization
120°
65°
1710 – 2170
–45°
1710 – 2170
+45°
7-16
7-16
30°
dB
3
3
dB
10
10
Mechanical specifications
0
0
Horizontal Pattern
Vertical Pattern
2° electrical downtilt
Input
2 x 7-16 female
Connector position
1920 – 2170 MHz: +45°/ –45° Polarization
Weight
Wind load
115°
63°
28°
Max. wind velocity
dB
3
0
Horizontal Pattern
3
dB
10
10
Bottom
2 kg
Frontal:
Lateral:
Rearside:
35 N (at 150 km/h)
25 N (at 150 km/h)
80 N (at 150 km/h)
200 km/h
Packing size
444 x 172 x 92 mm
Height/width/depth
342 / 155 / 69 mm
0
Vertical Pattern
0° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
83
Multi-band F-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electrical Downtilt
1710 –2170
X
65°
0°–10°
set by hand or by optional RCU (Remote Control Unit)
XPol F-Panel 1710–2170 65° 15.5dBi 0°–10°T
742 211
Type No.
Frequency range
Polarization
Gain
1710–2170
1850 – 1990 MHz
1920 – 2170 MHz
+45°, –45°
+45°, –45°
+45°, –45°
2 x 14.7 dBi
2 x 15 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal: 69°
Vertical: 14.5°
Electrical tilt
continuously adjustable
0°– 10°
Sidelobe suppression for
first sidelobe above horizon
Front-to-back ratio
Cross polar ratio
Maindirection
Sector
0°
±60°
Isolation, between ports
Horizontal:
Vertical:
2 x 15.2 dBi
67°
14°
Horizontal:
Vertical:
0°– 10°
64°
13°
0°– 10°
0° ... 4° ... 8° ... 10°T
0° ... 4° ... 8° ... 10°T
18 ... 16 ... 15 .... 15 dB 18 ... 18 ... 18 ... 18 dB
0° ... 4° ... 8° ... 10°T
18 ... 18 ... 18 ... 16 dB
Copolar:
> 30 dB
Total power: > 25 dB
Copolar:
> 30 dB
Total power: > 25 dB
Copolar:
> 30 dB
Total power: > 25 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
> 30 dB
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.4
< 1.4
< 1.4
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
300 W (at 50 °C ambient temperature)
1710 – 1880 MHz: +45°/ –45° Polarization
130°
69°
14.5°
10
dB
3
dB
10
3
0
0
Horizontal Pattern
Vertical Pattern
0°– 10° electrical downtilt
1850 – 1990 MHz: +45°/ –45° Polarization
128°
1710 – 2170
–45°
1710 – 2170
+45°
7-16
7-16
67°
14°
dB
dB
3
Mechanical specifications
10
10
Input
3
0
Horizontal Pattern
Vertical Pattern
0°– 10° electrical downtilt
1920 – 2170 MHz: +45°/ –45° Polarization
Adjustment
mechanism
Bottom
1x, Position bottom
continuously adjustable
Weight
Wind load
120°
2 x 7-16 female
Connector position
0
64°
4.5 kg
Frontal:
Lateral:
Rearside:
65 N (at 150 km/h)
50 N (at 150 km/h)
160 N (at 150 km/h)
13°
Max. wind velocity
3
dB
10
10
dB
XPol
1710 – 1880 MHz
3
200 km/h
Packing size
924 x 172 x 92 mm
Height/width/depth
662 / 155 / 69 mm
0
0
Horizontal Pattern
84
Vertical Pattern
0°– 10° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
Multi-band F-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electrical Downtilt
1710 –2170
X
65°
0°–12°
set by hand or by optional RCU (Remote Control Unit)
XPol F-Panel 1710–2170 65° 15.5dBi 0°–12°T
800 10247
Type No.
Frequency range
1710 – 1880 MHz
1710–2170
1850 – 1990 MHz
1920 – 2170 MHz
+45°, –45°
+45°, –45°
+45°, –45°
0° ... 4° ... 8° ... 12° T
15.5 ... 15.4 ... 15.9 ...15.1 dBi
0° ... 4° ... 8° ... 12° T
15.6 ... 15.5 ... 15.4 ...15 dBi
0° ... 4° ... 8° ... 12° T
15.8 ... 15.7 ... 15.5 ...14.9 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal: 67°
Vertical: 12.9°
Horizontal: 66°
Vertical: 12.3°
Horizontal: 64°
Vertical: 11.5°
Electrical tilt
continuously adjustable
0°– 12°
0°– 12°
0°– 12°
0° ... 4° ... 8° ... 12° T
14 ... 14 ... 14 .... 14 dB
0° ... 4° ... 8° ... 12° T
14 ... 14 ... 14 ... 14 dB
0° ... 4° ... 8° ... 12° T
14 ... 14 ... 14 ... 14 dB
Gain
per input
Sidelobe suppression for
first sidelobe above horizon
Front-to-back ratio
Copolar:
Cross polar ratio
Maindirection
Sector
0°
±60°
Isolation, between ports
> 27 dB
Copolar:
> 27 dB
Copolar:
> 27 dB
Typically: 20 dB
> 10 dB
Typically: 20 dB
> 10 dB
Typically: 20 dB
> 10 dB
> 30 dB
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
300 W (at 50 °C ambient temperature)
XPol
Polarization
1710 – 1880 MHz: +45°/ –45° Polarization
122°
67°
12.9°
10
dB
3
dB
10
3
0
0
Horizontal Pattern
Vertical Pattern
0°– 12° electrical downtilt
1850 – 1990 MHz: +45°/ –45° Polarization
122°
1710 – 2170
–45°
1710 – 2170
+45°
7-16
7-16
66°
12.3°
dB
dB
3
Mechanical specifications
10
10
Input
3
0
Horizontal Pattern
Vertical Pattern
0°– 12° electrical downtilt
1920 – 2170 MHz: +45°/ –45° Polarization
Adjustment
mechanism
Bottom
1x, Position bottom
continuously adjustable
Weight
Wind load
120°
2 x 7-16 female
Connector position
0
64°
4.5 kg
Frontal:
Lateral:
Rearside:
75 N (at 150 km/h)
55 N (at 150 km/h)
180 N (at 150 km/h)
11.5°
Max. wind velocity
10
Packing size
dB
3
dB
10
3
Height/width/depth
200 km/h
1000 x 172 x 95 mm
735 / 155 / 69 mm
0
0
Horizontal Pattern
Vertical Pattern
0°– 12° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
85
Multi-band F-Panel
Dual Polarization
Half-power Beam Width
Fixed Electrical Downtilt
1710 –2170
X
65°
0°
XPol F-Panel 1710–2170 65° 16dBi 0°T
742 196
Type No.
Frequency range
1710 – 1880 MHz
1920 – 2170 MHz
Polarization
+45°, –45°
+45°, –45°
+45°, –45°
Gain
2 x 15.3 dBi
2 x 15.6 dBi
2 x 15.8 dBi
Horizontal: 67°
Vertical: 12.6°
Horizontal: 66°
Vertical: 11.8°
> 14 dB
> 16 dB
> 14 dB
Copolar:
> 30 dB
Total power: > 25 dB
Copolar:
> 30 dB
Total power: > 25 dB
Copolar:
> 30 dB
Total power: > 25 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
Half-power beam width
Copolar +45°/ –45°
Sidelobe suppression for
first sidelobe above horizon
Front-to-back ratio
(180° ± 30°)
Cross polar ratio
Maindirection
Sector
0°
±60°
Isolation, between ports
Horizontal:
Vertical:
64°
11°
> 30 dB
50 Ω
Impedance
VSWR
< 1.4
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
300 W (at 50 °C ambient temperature)
1710 – 1880 MHz: +45°/ –45° Polarization
125°
67°
12.6°
dB
3
3
dB
10
10
0
0
Horizontal Pattern
Vertical Pattern
1850 – 1990 MHz: +45°/ –45° Polarization
125°
1710 – 2170
–45°
1710 – 2170
+45°
7-16
7-16
66°
11.8°
dB
3
3
dB
10
10
0
Mechanical specifications
0
Horizontal Pattern
Vertical Pattern
Input
1920 – 2170 MHz: +45°/ –45° Polarization
120°
3
Packing size
dB
3
Max. wind velocity
10
Height/width/depth
0
0
Horizontal Pattern
86
Bottom
Weight
11.1°
10
2 x 7-16 female
Connector position
Wind load
64°
dB
XPol
1710–2170
1850 – 1990 MHz
3.7 kg
Frontal:
Lateral:
Rearside:
75 N (at 150 km/h)
55 N (at 150 km/h)
180 N (at 150 km/h)
200 km/h
1000 x 172 x 95 mm
735 / 155 / 69 mm
Vertical Pattern
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
Multi-band F-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electrical Downtilt
1710 –2170
X
65°
0°– 8°
set by hand or by optional RCU (Remote Control Unit)
XPol F-Panel 1710–2170 65° 18dBi 0°–8°T
742 212
Frequency range
Polarization
Gain
1710 – 1880 MHz
1710–2170
1850 – 1990 MHz
1920 – 2170 MHz
+45°, –45°
+45°, –45°
+45°, –45°
2 x 17.5 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
Electrical tilt
continuously adjustable
0°– 8°
Sidelobe suppression for
first sidelobe above horizon
Front-to-back ratio
(180° ± 30°)
Cross polar ratio
Maindirection
Sector
0°
±60°
Isolation, between ports
67°
7°
2 x 17.7 dBi
2 x 18 dBi
Horizontal: 65°
Vertical:
6.7°
Horizontal: 63°
Vertical:
6.5°
0°– 8°
0°– 8°
0° ... 2° ... 5° ... 8° T
0° ... 2° ... 5° ... 8° T
17 ... 17 ... 15 .... 15 dB 20 ... 20 ... 18 ... 18 dB
0° ... 2° ... 5° ... 8° T
20 ... 20 ... 18 ... 16 dB
Copolar:
> 30 dB
Total power: > 25 dB
Copolar:
> 30 dB
Total power: > 25 dB
Copolar:
> 30 dB
Total power: > 25 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
> 30 dB
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
300 W (at 50 °C ambient temperature)
XPol
Type No.
1710 – 1880 MHz: +45°/ –45° Polarization
125°
67°
7°
dB
3
3
dB
10
10
0
0
Horizontal Pattern
Vertical Pattern
0°– 8° electrical downtilt
1850 – 1990 MHz: +45°/ –45° Polarization
120°
1710 – 2170
–45°
1710 – 2170
+45°
7-16
7-16
65°
6.7°
3
Input
dB
dB
3
Mechanical specifications
10
10
Horizontal Pattern
Vertical Pattern
0°– 8° electrical downtilt
1920 – 2170 MHz: +45°/ –45° Polarization
Adjustment
mechanism
Bottom
1x, Position bottom
continuously adjustable
Weight
Wind load
120°
2 x 7-16 female
Connector position
0
0
63°
7.5 kg
Frontal:
Lateral:
Rearside:
130 N (at 150 km/h)
110 N (at 150 km/h)
310 N (at 150 km/h)
6.5°
Max. wind velocity
dB
3
0
Horizontal Pattern
3
dB
10
10
200 km/h
Packing size
1574 x 172 x 92 mm
Height/width/depth
1302 / 155 / 69 mm
0
Vertical Pattern
0°– 8° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
87
Multi-band F-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electrical Downtilt
1710 –2170
X
65°
0°– 10°
set by hand or by optional RCU (Remote Control Unit)
XPol F-Panel 1710–2170 65° 18dBi 0°–10°T
742 215
Type No.
Frequency range
Polarization
Gain
1710–2170
1850 – 1990 MHz
1920 – 2170 MHz
+45°, –45°
+45°, –45°
+45°, –45°
2 x 17.5 dBi
Half-power beam width
Copolar +45°/ –45°
Sidelobe suppression for
first sidelobe above horizon
Front-to-back ratio
(180° ± 30°)
Cross polar ratio
Maindirection
Sector
2 x 17.7 dBi
2 x 18 dBi
Horizontal: 65°
Vertical:
6.7°
Horizontal: 63°
Vertical:
6.5°
0°– 10°
0°– 10°
0°– 10°
0° ... 5° ... 10°T
16 ... 15 ... 14 dB
0° ... 5° ... 10°T
17 ... 16 ... 15 dB
0° ... 5° ... 10°T
17 ... 16 ... 15 dB
Copolar:
> 30 dB
Total power: > 25 dB
Copolar:
> 30 dB
Total power: > 25 dB
Copolar:
> 30 dB
Total power: > 25 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
> 30 dB
> 30 dB
> 30 dB
Horizontal:
Vertical:
Electrical tilt
continuously adjustable
0°
±60°
Isolation, between ports
67°
7°
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
300 W (at 50 °C ambient temperature)
1710 – 1880 MHz: +45°/ –45° Polarization
125°
67°
7°
dB
3
3
dB
10
10
0
0
Horizontal Pattern
Vertical Pattern
0°– 10° electrical downtilt
1850 – 1990 MHz: +45°/ –45° Polarization
120°
1710 – 2170
–45°
1710 – 2170
+45°
7-16
7-16
65°
6.7°
3
Input
dB
dB
3
Mechanical specifications
10
10
Horizontal Pattern
Vertical Pattern
0°– 10° electrical downtilt
1920 – 2170 MHz: +45°/ –45° Polarization
Adjustment
mechanism
Bottom
1x, Position bottom
continuously adjustable
Weight
Wind load
120°
2 x 7-16 female
Connector position
0
0
63°
7.5 kg
Frontal:
Lateral:
Rearside:
130 N (at 150 km/h)
110 N (at 150 km/h)
310 N (at 150 km/h)
6.5°
Max. wind velocity
3
0
Horizontal Pattern
88
3
dB
10
10
dB
XPol
1710 – 1880 MHz
200 km/h
Packing size
1574 x 172 x 92 mm
Height/width/depth
1302 / 155 / 69 mm
0
Vertical Pattern
0°– 10° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
Multi-band F-Panel
Dual Polarization
Half-power Beam Width
Fixed Electrical Downtilt
1710 –2170
X
65°
2°
XPol F-Panel 1710–2170 65° 18.5dBi 2°T
741 794
Frequency range
1710 – 1880 MHz
1710–2170
1850 – 1990 MHz
Polarization
+45°, –45°
+45°, –45°
+45°, –45°
Gain
2 x 17.5 dBi
2 x 18 dBi
2 x 18.5 dBi
Horizontal: 65°
Vertical:
6.7°
Horizontal: 63°
Vertical:
6.5°
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
67°
7°
1920 – 2170 MHz
Electrical tilt
2°, fixed
2°, fixed
2°, fixed
Sidelobe suppression for
first sidelobe above horizon
> 14 dB
> 14 dB
> 14 dB
Front-to-back ratio, copolar
> 30 dB
> 30 dB
> 30 dB
Typically: 30 dB
> 10 dB
Typically: 30 dB
> 10 dB
Typically: 30 dB
> 10 dB
Cross polar ratio
Maindirection
Sector
0°
±60°
Isolation, between ports
XPol
Type No.
> 30 dB
50 Ω
Impedance
VSWR
< 1.4
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
300 W (at 50 °C ambient temperature)
1710 – 1880 MHz: +45°/ –45° Polarization
125°
67°
7°
dB
3
3
dB
10
10
0
0
Horizontal Pattern
Vertical Pattern
2° electrical downtilt
1850 – 1990 MHz: +45°/ –45° Polarization
120°
1710 – 2170
–45°
1710 – 2170
+45°
7-16
7-16
65°
6.7°
dB
3
3
dB
10
10
Mechanical specifications
0
0
Horizontal Pattern
Vertical Pattern
2° electrical downtilt
Input
2 x 7-16 female
Connector position
1920 – 2170 MHz: +45°/ –45° Polarization
Weight
Wind load
115°
63°
6.5°
Max. wind velocity
dB
3
0
Horizontal Pattern
3
dB
10
10
Bottom
6.6 kg
Frontal:
Lateral:
Rearside:
130 N (at 150 km/h)
110 N (at 150 km/h)
310 N (at 150 km/h)
200 km/h
Packing size
1404 x 172 x 92 mm
Height/width/depth
1302 / 155 / 69 mm
0
Vertical Pattern
2° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
89
Multi-band F-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electrical Downtilt
1710 –2170
X
65°
0°– 6°
set by hand or by optional RCU (Remote Control Unit)
XPol F-Panel 1710–2170 65° 19.5dBi 0°–6°T
742 213
Type No.
Frequency range
Polarization
Gain
1710–2170
1850 – 1990 MHz
1920 – 2170 MHz
+45°, –45°
+45°, –45°
+45°, –45°
2 x 19 dBi
2 x 19.2 dBi
2 x 19.5 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal: 67°
Vertical:
4.7°
Horizontal: 65°
Vertical:
4.5°
Horizontal: 63°
Vertical:
4.3°
Electrical tilt
continuously adjustable
0°– 6°
0°– 6°
0°– 6°
Sidelobe suppression for
first sidelobe above horizon
Front-to-back ratio
(180° ± 30°)
Cross polar ratio
Maindirection
Sector
0°
±60°
Isolation, between ports
0° ... 2° ... 4° ... 6° T
0° ... 2° ... 4° ... 6° T
18 ... 17 ... 15 .... 15 dB 18 ... 18 ... 17 ... 15 dB
0° ... 2° ... 4° ... 6° T
18 ... 18 ... 17 ... 15 dB
Copolar:
> 30 dB
Total power: > 25 dB
Copolar:
> 30 dB
Total power: > 25 dB
Copolar:
> 30 dB
Total power: > 25 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
> 30 dB
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
300 W (at 50 °C ambient temperature)
1710 – 1880 MHz: +45°/ –45° Polarization
125°
67°
4.7°
dB
3
3
dB
10
10
0
0
Horizontal Pattern
Vertical Pattern
0°– 6° electrical downtilt
1850 – 1990 MHz: +45°/ –45° Polarization
120°
1710 – 2170
–45°
1710 – 2170
+45°
7-16
7-16
65°
4.5°
3
Input
dB
dB
3
Mechanical specifications
10
10
Horizontal Pattern
Vertical Pattern
0°– 6° electrical downtilt
1920 – 2170 MHz: +45°/ –45° Polarization
Adjustment
mechanism
Bottom
1x, Position bottom
continuously adjustable
Weight
Wind load
115°
2 x 7-16 female
Connector position
0
0
63°
10 kg
Frontal:
Lateral:
Rearside:
195 N (at 150 km/h)
160 N (at 150 km/h)
480 N (at 150 km/h)
4.3°
Max. wind velocity
3
0
Horizontal Pattern
90
3
dB
10
10
dB
XPol
1710 – 1880 MHz
200 km/h
Packing size
2384 x 172 x 92 mm
Height/width/depth
1942 / 155 / 69 mm
0
Vertical Pattern
0°– 6° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
Multi-band F-Panel
Dual Polarization
Half-power Beam Width
Excellent Sidelobe Suppression
1710 –2170
X
88°
20 dB
XPol F-Panel 1710–2170 88° 11.5dBi
741 984
Type No.
Frequency range
1710–2170
1850 – 1990 MHz
1710 – 1880 MHz
1920 – 2170 MHz
Polarization
+45°, –45°
+45°, –45°
+45°, –45°
Gain
2 x 11.3 dBi
2 x 11.5 dBi
2 x 11.6 dBi
Horizontal:
Vertical:
Sidelobe suppression
vertical sector ±45°
Front-to-back ratio
(180° ± 30°)
Cross polar ratio
Maindirection
Sector
0°
±60°
86°
28°
Horizontal:
Vertical:
87°
26°
Horizontal:
Vertical:
88°
26°
> 20 dB
> 20 dB
> 20 dB
Copolar:
> 23 dB
Total power: > 23 dB
Copolar:
> 23 dB
Total power: > 23 dB
Copolar:
> 23 dB
Total power: > 23 dB
Typically: 20 dB
> 18 dB
Typically: 25 dB
> 18 dB
Typically: 20 dB
> 15 dB
Isolation, between ports
XPol
Half-power beam width
Copolar +45°/ –45°
> 30 dB
50 Ω
Impedance
VSWR
< 1.4
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
150 W (at 50 °C ambient temperature)
1710 – 1880 MHz: +45°/ –45° Polarization
86°
155°
28°
10
3
0
dB
3
dB
10
0
Horizontal Pattern
Vertical Pattern
1850 – 1990 MHz: +45°/ –45° Polarization
1710 – 2170
–45°
1710 – 2170
+45°
7-16
7-16
87°
160°
26°
10
Mechanical specifications
3
0
dB
3
dB
10
Input
0
Horizontal Pattern
Connector position*
Vertical Pattern
2 x 7-16 female
Bottom or top
Weight
1920 – 2170 MHz: +45°/ –45° Polarization
Wind load
88°
160°
Max. wind velocity
26°
Packing size
Height/width/depth
2 kg
Frontal:
Lateral:
Rearside:
35 N (at 150 km/h)
25 N (at 150 km/h)
80 N (at 150 km/h)
200 km/h
444 x 172 x 92 mm
342 / 155/ 69 mm
10
0
Horizontal Pattern
3
dB
3
dB
10
* Inverted mounting:
Connector position top: Change drain hole screw.
0
Vertical Pattern
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
91
Multi-band F-Panel
Dual Polarization
Half-power Beam Width
Fixed Electrical Downtilt
1710 –2170
X
88°
2°
XPol F-Panel 1710–2170 88° 17dBi 2°T
741 987
Type No.
Frequency range
1710 – 1880 MHz
1920 – 2170 MHz
Polarization
+45°, –45°
+45°, –45°
+45°, –45°
Gain
2 x 16.5 dBi
2 x 16.8 dBi
2 x 17 dBi
Horizontal: 88°
Vertical:
6.9°
Horizontal: 88°
Vertical:
6.5°
Horizontal: 88°
Vertical:
6.2°
Electrical tilt
2°, fixed
2°, fixed
2°, fixed
Sidelobe suppression for
first sidelobe above horizon
> 16 dB
> 16 dB
> 16 dB
Copolar:
> 25 dB
Total power: > 25 dB
Copolar:
> 25 dB
Total power: > 25 dB
Copolar:
> 25 dB
Total power: > 25 dB
Typically: 20 dB
> 10 dB
Typically: 20 dB
> 10 dB
Typically: 20 dB
> 10 dB
Half-power beam width
Copolar +45°/ –45°
Front-to-back ratio
(180° ± 30°)
Cross polar ratio
Maindirection
Sector
0°
±60°
Isolation, between ports
> 30 dB
Impedance
50 Ω
VSWR
< 1.4
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
300 W (at 50 °C ambient temperature)
1710 – 1880 MHz: +45°/ –45° Polarization
88°
160°
6.9°
10
3
0
dB
3
dB
10
0
Horizontal Pattern
Vertical Pattern
2° electrical downtilt
1850 – 1990 MHz: +45°/ –45° Polarization
88°
1710 – 2170
–45°
1710 – 2170
+45°
7-16
7-16
162°
6.5°
10
3
0
dB
3
dB
10
Mechanical specifications
0
Horizontal Pattern
Vertical Pattern
2° electrical downtilt
1920 – 2170 MHz: +45°/ –45° Polarization
Input
6.2°
Max. wind velocity
3
0
Horizontal Pattern
92
3
dB
10
Bottom
Weight
163°
10
2 x 7-16 female
Connector position
Wind load
88°
dB
XPol
1710–2170
1850 – 1990 MHz
6.5 kg
Frontal:
Lateral:
Rearside:
130 N (at 150 km/h)
110 N (at 150 km/h)
310 N (at 150 km/h)
200 km/h
Packing size
1404 x 172 x 92 mm
Height/width/depth
1302 / 155 / 69 mm
0
Vertical Pattern
2° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
Multi-band F-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electrical Downtilt
1710 –2170
X
88°
0°– 10°
set by hand or by optional RCU (Remote Control Unit)
XPol F-Panel 1710–2170 88° 14dBi 0°–10°T
741 988
Type No.
Frequency range
Gain
1710–2170
1850 – 1990 MHz
1920 – 2170 MHz
+45°, –45°
+45°, –45°
+45°, –45°
2 x 13.7 dBi
2 x 14 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal: 88°
Vertical: 14.7°
Electrical tilt
continuously adjustable
0° – 10°
Sidelobe suppression for
first sidelobe above horizon
Front-to-back ratio, copolar
total power
Cross polar ratio
Maindirection
Sector
0°
±60°
Isolation, between ports
Horizontal:
Vertical:
2 x 14.1 dBi
88°
14°
Horizontal:
Vertical:
0° – 10°
88°
13°
0° – 10°
0° ... 4° ... 8° ... 10° T 0° ... 4° ... 8° ... 10° T 0° ... 4° ... 8° ... 10° T
18 ... 18 ... 18 ... 18 dB 18 ... 18 ... 18 ... 18 dB 18 ... 18 ... 18 ... 18 dB
> 25 dB
> 25 dB
> 25 dB
> 25 dB
> 25 dB
> 25 dB
Typically: 20 dB
> 10 dB
Typically: 20 dB
> 10 dB
Typically: 20 dB
> 10 dB
> 30 dB
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
300 W (at 50 °C ambient temperature)
XPol
Polarization
1710 – 1880 MHz
1710 – 1880 MHz: +45°/ –45° Polarization
88°
160°
14.7°
10
dB
3
dB
10
3
0
0
Horizontal Pattern
Vertical Pattern
0°– 10° electrical downtilt
1850 – 1990 MHz: +45°/ –45° Polarization
1710 – 2170
–45°
1710 – 2170
+45°
7-16
7-16
88°
163°
14°
Mechanical specifications
10
dB
3
dB
10
Input
3
0
Horizontal Pattern
Vertical Pattern
0°– 10° electrical downtilt
1920 – 2170 MHz: +45°/ –45° Polarization
Adjustment
mechanism
165°
13°
Max. wind velocity
10
Horizontal Pattern
dB
3
dB
10
3
Bottom
1x, Position bottom
continuously adjustable
Weight
Wind load
88°
0
2 x 7-16 female
Connector position
0
4.2 kg
Frontal:
Lateral:
Rearside:
65 N (at 150 km/h)
50 N (at 150 km/h)
160 N (at 150 km/h)
200 km/h
Packing size
924 x 172 x 92 mm
Height/width/depth
662 / 155 / 69 mm
0
Vertical Pattern
0°– 10° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
93
Multi-band F-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electrical Downtilt
1710 –2170
X
88°
0°– 8°
set by hand or by optional RCU (Remote Control Unit)
XPol F-Panel 1710–2170 88° 17dBi 0°–8°T
741 989
Type No.
Frequency range
Polarization
Gain
1710–2170
1850 – 1990 MHz
1920 – 2170 MHz
+45°, –45°
+45°, –45°
+45°, –45°
2 x 16.5 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
Electrical tilt
continuously adjustable
0°– 8°
Sidelobe suppression for
first sidelobe above horizon
Front-to-back ratio
(180° ± 30°)
Cross polar ratio
Maindirection
Sector
0°
±60°
Isolation, between ports
88°
7°
2 x 16.8 dBi
2 x 16.7 dBi
Horizontal: 88°
Vertical:
6.7°
Horizontal: 88°
Vertical:
6.5°
0°– 8°
0°– 8°
0° ... 2° ... 5° ... 8° T
0° ... 2° ... 5° ... 8° T
18 ... 18 ... 16 .... 14 dB 20 ... 20 ... 18 ... 17 dB
0° ... 2° ... 5° ... 8° T
18 ... 18 ... 18 ... 17 dB
Copolar:
> 25 dB
Total power: > 25 dB
Copolar:
> 25 dB
Total power: > 25 dB
Copolar:
> 24 dB
Total power: > 24 dB
Typically: 20 dB
> 10 dB
Typically: 20 dB
> 10 dB
Typically: 20 dB
> 10 dB
> 30 dB
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
300 W (at 50 °C ambient temperature)
1710 – 1880 MHz: +45°/ –45° Polarization
88°
165°
7°
10
3
0
dB
3
dB
10
0
Horizontal Pattern
Vertical Pattern
0°– 8° electrical downtilt
1850 – 1990 MHz: +45°/ –45° Polarization
1710 – 2170
–45°
1710 – 2170
+45°
7-16
7-16
88°
165°
6.7°
Mechanical specifications
10
3
0
Input
dB
3
dB
10
Horizontal Pattern
Vertical Pattern
0°– 8° electrical downtilt
1920 – 2170 MHz: +45°/ –45° Polarization
Adjustment
mechanism
165°
6.5°
Max. wind velocity
10
3
Horizontal Pattern
94
3
dB
10
Bottom
1x, Position bottom
continuously adjustable
Weight
Wind load
88°
0
2 x 7-16 female
Connector position
0
dB
XPol
1710 – 1880 MHz
7.5 kg
Frontal:
Lateral:
Rearside:
130 N (at 150 km/h)
110 N (at 150 km/h)
310 N (at 150 km/h)
200 km/h
Packing size
1574 x 172 x 92 mm
Height/width/depth
1302 / 155 / 69 mm
0
Vertical Pattern
0°– 8° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
Multi-band F-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electrical Downtilt
1710 –2170
X
88°
0°– 6°
set by hand or by optional RCU (Remote Control Unit)
XPol F-Panel 1710–2170 88° 18dBi 0°–6°T
741 990
Type No.
Frequency range
Gain
1710–2170
1850 – 1990 MHz
1920 – 2170 MHz
+45°, –45°
+45°, –45°
+45°, –45°
2 x 17.7 dBi
2 x 18 dBi
2 x 18.2 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal: 88°
Vertical:
4.9°
Horizontal: 88°
Vertical:
4.7°
Horizontal: 88°
Vertical:
4.5°
Electrical tilt
continuously adjustable
0°– 6°
0°– 6°
0°– 6°
Sidelobe suppression for
first sidelobe above horizon
Front-to-back ratio, copolar
total power
Cross polar ratio
Maindirection
Sector
0°
±60°
Isolation, between ports
0° ... 2° ... 4° ... 6° T
0° ... 2° ... 4° ... 6° T
0° ... 2° ... 4° ... 6° T
17 ... 17 ... 17 ...17 dB 18 ... 18 ... 18 ...18 dB 18 ... 18 ... 18 ...18 dB
> 25 dB
> 25 dB
> 25 dB
> 25 dB
> 25 dB
> 25 dB
Typically: 20 dB
> 10 dB
Typically: 20 dB
> 10 dB
Typically: 20 dB
> 10 dB
> 30 dB
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
300 W (at 50 °C ambient temperature)
XPol
Polarization
1710 – 1880 MHz
1710 – 1880 MHz: +45°/ –45° Polarization
88°
165°
4.9°
10
3
0
dB
3
dB
10
0
Horizontal Pattern
Vertical Pattern
0°– 6° electrical downtilt
1850 – 1990 MHz: +45°/ –45° Polarization
1710 – 2170
–45°
1710 – 2170
+45°
7-16
7-16
88°
165°
4.7°
Mechanical specifications
10
3
0
Input
dB
3
dB
10
Horizontal Pattern
2 x 7-16 female
Connector position
0
Vertical Pattern
0°– 6° electrical downtilt
1920 – 2170 MHz: +45°/ –45° Polarization
Adjustment
mechanism
1x, Position bottom
continuously adjustable
Weight
Wind load
88°
Bottom
165°
9 kg
Frontal:
Lateral:
Rearside:
195 N (at 150 km/h)
160 N (at 150 km/h)
480 N (at 150 km/h)
4.5°
Max. wind velocity
10
0
Horizontal Pattern
3
dB
3
dB
10
200 km/h
Packing size
2214 x 172 x 92 mm
Height/width/depth
1942 / 155 / 69 mm
0
Vertical Pattern
0°– 6° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
95
96
Summary – Directional Antennas
2-Multi-band
UMTS
Dual Polarization + 45°/ –45° – 1800/1900/2000
Type
Type No.
Height
[mm]
Page
XXPol F-Panel
1710–2170
1710–2170
65°
65°
15dBi
15dBi
0°–10°T
0°–10°T
742 233
679
98
XXPol F-Panel
1710–2170
1710–2170
65°
65°
18dBi
18dBi
0°–8°T
0°–8°T
742 234
1304
99
XXPol F-Panel
1710–2170
1710–2170
65°
65°
19.5dBi
19.5dBi
0°–6°T
0°–6°T
742 235
1959
100
UMTS
XXPol 2-Multi
Connector position: Bottom
97
2-Multi-band F-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electr. Downtilt
1710 –2170 1710 –2170
X
X
65°
65°
0°– 10°
0°– 10°
set by hand or by optional RCU (Remote Control Unit)
XXPol F-Panel 1710–2170/1710–2170 65°/65° 15/15dBi 0°–10°/0°–10°T
742 233
Type No.
Frequency range
1710 – 1880 MHz
Polarization
1710–2170
1850 – 1990 MHz
1920 – 2170 MHz
+45°, –45°; +45°, –45° +45°, –45°; +45°, –45° +45°, –45°; +45°, –45°
Gain
4 x 15 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
Electrical tilt
continuously adjustable
Front-to-back ratio
0°
±60°
Isolation, between inputs
4 x 15.3 dBi
Horizontal: 65°
Vertical: 13.7°
0° – 10°
Sidelobe suppression for
first sidelobe above horizon
Cross polar ratio
Maindirection
Sector
4 x 15.2 dBi
67°
14°
Horizontal:
Vertical:
0° – 10°
62°
13°
0° – 10°
0° ... 4° ... 8° ... 10°T
0° ... 4° ... 8° ... 10°T
16 ... 16 ... 15 .... 15 dB 16 ... 16 ... 16 ... 16 dB
0° ... 4° ... 8° ... 10°T
16 ... 16 ... 16 ... 16 dB
Copolar:
> 25 dB
Total power: > 25 dB
Copolar:
> 25 dB
Total power: > 25 dB
Copolar:
> 25 dB
Total power: > 25 dB
Typically: 20 dB
Typically: 10 dB
Typically: 20 dB
Typically: 10 dB
Typically: 20 dB
Typically: 10 dB
> 30 dB
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
250 W (at 50 °C ambient temperature)
1710 – 1880 MHz: +45°/ –45° Polarization
130°
67°
14°
10
dB
3
dB
10
3
0
0
Horizontal Pattern
Vertical Pattern
0°– 10° electrical downtilt
1850 – 1990 MHz: +45°/ –45° Polarization
125°
1710 – 2170
+45°
1710 – 2170
–45°
1710 – 2170
+45°
1710 –2170
–45°
7-16
7-16
7-16
7-16
65°
13.7°
dB
dB
3
Mechanical specifications
10
10
Input
3
0
Horizontal Pattern
Vertical Pattern
0°– 10° electrical downtilt
1920 – 2170 MHz: +45°/ –45° Polarization
Adjustment
mechanism
Bottom
2 x, Position bottom
continuously adjustable
Weight
Wind load
120°
4 x 7-16 female
Connector position
0
62°
10.4 kg
Frontal:
Lateral:
Rearside:
290 N (at 150 km/h)
55 N (at 150 km/h)
290 N (at 150 km/h)
13°
Max. wind velocity
10
Packing size
dB
3
dB
10
3
Height/width/depth
200 km/h
924 x 360 x 130 mm
679 / 322 / 71 mm
0
0
Horizontal Pattern
98
Vertical Pattern
0°– 10° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
2-Multi-band F-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electr. Downtilt
1710 –2170 1710 –2170
X
X
65°
65°
0°– 8°
0°– 8°
set by hand or by optional RCU (Remote Control Unit)
XXPol F-Panel 1710–2170/1710–2170 65°/65° 18/18dBi 0°–8°/0°–8°T
742 234
Type No.
Frequency range
1710 – 1880 MHz
1920 – 2170 MHz
+45°, –45°; +45°, –45° +45°, –45°; +45°, –45° +45°, –45°; +45°, –45°
Gain
4 x 17.5 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal:
Vertical:
Electrical tilt
continuously adjustable
0° – 8°
Sidelobe suppression for
first sidelobe above horizon
Front-to-back ratio
Cross polar ratio
Maindirection
Sector
0°
±60°
Isolation, between inputs
66°
7°
4 x 17.7 dBi
4 x 17.8 dBi
Horizontal: 65°
Vertical:
6.7°
Horizontal: 64°
Vertical:
6.5°
0° – 8°
0° – 8°
0° ... 2° ... 5° ... 8° T
0° ... 2° ... 5° ... 8° T
17 ... 17 ... 15 .... 15 dB 20 ... 20 ... 18 ... 18 dB
0° ... 2° ... 5° ... 8° T
20 ... 20 ... 18 ... 16 dB
Copolar:
> 25 dB
Total power: > 25 dB
Copolar:
> 25 dB
Total power: > 25 dB
Copolar:
> 25 dB
Total power: > 25 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
> 30 dB
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
300 W (at 50 °C ambient temperature)
XXPol 2-Multi
Polarization
1710–2170
1850 – 1990 MHz
1710 – 1880 MHz: +45°/ –45° Polarization
130°
66°
7°
dB
3
3
dB
10
10
0
0
Horizontal Pattern
Vertical Pattern
0°– 8° electrical downtilt
1850 – 1990 MHz: +45°/ –45° Polarization
125°
1710 – 2170
+45°
1710 – 2170
–45°
1710 – 2170
+45°
1710 –2170
–45°
7-16
7-16
7-16
7-16
65°
6.7°
3
Input
dB
dB
3
Mechanical specifications
10
10
0
Horizontal Pattern
Vertical Pattern
0°– 8° electrical downtilt
1920 – 2170 MHz: +45°/ –45° Polarization
Adjustment
mechanism
Bottom
2 x, Position bottom
continuously adjustable
Weight
Wind load
120°
4 x 7-16 female
Connector position
0
64°
12 kg
Frontal:
Lateral:
Rearside:
570 N (at 150 km/h)
110 N (at 150 km/h)
570 N (at 150 km/h)
6.5°
Max. wind velocity
dB
3
3
dB
10
10
200 km/h
Packing size
1574 x 320 x 92 mm
Height/width/depth
1304 / 299 / 69 mm
0
0
Horizontal Pattern
Vertical Pattern
0°– 8° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
99
2-Multi-band F-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electr. Downtilt
1710 –2170 1710 –2170
X
X
65°
65°
0°– 6°
0°– 6°
set by hand or by optional RCU (Remote Control Unit)
XXPol F-Panel 1710–2170/1710–2170 65°/65° 19.5/19.5dBi 0°–6°/0°–6°T
742 235
Type No.
Frequency range
1710 – 1880 MHz
Polarization
1920 – 2170 MHz
+45°, –45°; +45°, –45° +45°, –45°; +45°, –45° +45°, –45°; +45°, –45°
Gain
4 x 19 dBi
4 x 19.2 dBi
4 x 19.5 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal: 65°
Vertical:
4.6°
Horizontal: 64°
Vertical:
4.4°
Horizontal: 63°
Vertical:
4.2°
Electrical tilt
continuously adjustable
0° – 6°
0° – 6°
0° – 6°
Sidelobe suppression for
first sidelobe above horizon
Front-to-back ratio
Cross polar ratio
Maindirection
Sector
0°
±60°
Isolation, between inputs
0° ... 2° ... 4° ... 6°T
0° ... 2° ... 4° ... 6°T
17 ... 17 ... 14 .... 14 dB 17 ... 17 ... 15 ... 15 dB
0° ... 2° ... 4° ... 6°T
17 ... 17 ... 15 ... 15 dB
Copolar:
> 30 dB
Total power: > 25 dB
Copolar:
> 30 dB
Total power: > 25 dB
Copolar:
> 30 dB
Total power: > 24 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
Typically: 25 dB
> 10 dB
> 30 dB
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
300 W (at 50 °C ambient temperature)
1710 – 1880 MHz: +45°/ –45° Polarization
130°
65°
4.6°
dB
3
3
dB
10
10
0
0
Horizontal Pattern
Vertical Pattern
0°– 6° electrical downtilt
1850 – 1990 MHz: +45°/ –45° Polarization
127°
1710 – 2170
+45°
1710 – 2170
–45°
1710 – 2170
+45°
1710 –2170
–45°
7-16
7-16
7-16
7-16
64°
4.4°
3
Input
dB
dB
3
Mechanical specifications
10
10
0
Horizontal Pattern
Vertical Pattern
0°– 6° electrical downtilt
1920 – 2170 MHz: +45°/ –45° Polarization
Adjustment
mechanism
63°
4.2°
10
3
3
Max. wind velocity
Packing size
dB
10
Bottom
2 x, Position bottom
continuously adjustable
Weight
Wind load
124°
4 x 7-16 female
Connector position
0
dB
XXPol 2-Multi
1710–2170
1850 – 1990 MHz
Height/width/depth
18 kg
Frontal:
Lateral:
Rearside:
870 N (at 150 km/h)
230 N (at 150 km/h)
870 N (at 150 km/h)
200 km/h
2384 x 360 x 130 mm
1959 / 323 / 71 mm
0
0
Horizontal Pattern
100
Vertical Pattern
0°– 6° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
Summary – Directional Antennas
Dual-band
UMTS
Dual Polarization + 45°/ –45° – 800/900 1800/1900/2000
Type
806– 960
1710–2170
XXPol A-Panel
806– 960
1710–2170
XXPol A-Panel
Height
[mm]
Page
65°
60°
12dBi
14dBi
0°T
0°T
742 226
579
102
65°
60°
12dBi
14dBi
0°T
0°T
742 222
579
103
824– 960
1710–2170
65°
65°
14dBi
17dBi
0°–14°T
0°–8°T
742 264
1316
104
XXPol A-Panel
824– 960
1710–2170
65°
65°
16dBi
18.5dBi
0°–10°T
0°–6°T
742 265
1916
105
XXPol A-Panel
824– 960
1710–2170
65°
65°
17dBi
18.5dBi
0°–7°T
0°–6°T
742 266
2516
106
Connector position: Bottom
C
New Product
UMTS
XXPol Dual-b.
XXPol A-Panel
Type No.
101
Dual-band A-Panel
Dual Polarization
Half-power Beam Width
Fixed Electr. Downtilt
806 – 960
1710 –2170
X
X
65°
60°
0°
0°
XXPol A-Panel 806–960/1710–2170 65°/ 60° 12/14dBi 0°/0°T
742 226
Type No.
Frequency range
806 –960
1710–2170
806 – 866 MHz 824 – 894 MHz 880 – 960 MHz 1710 – 1880 MHz1850 – 1990 MHz1920 – 2170 MHz
Polarization
+45°, –45°
+45°, –45°
+45°, –45°
+45°, –45°
+45°, –45°
+45°, –45°
Gain
2 x 11.1 dBi
2 x 11.4 dBi
2 x 11.8 dBi
2 x 12.8 dBi
2 x 13.3 dBi
2 x 13.6 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal: 67° Horizontal: 66° Horizontal: 64° Horizontal: 66° Horizontal: 60° Horizontal: 60°
Vertical:
34° Vertical:
33° Vertical:
30° Vertical:
20° Vertical:
18° Vertical: 17.5°
Front-to-back ratio
(180° ± 30°)
Cross polar ratio
Maindirection
Sector
[dB]
[dB]
Copolar: > 23 Copolar: > 23 Copolar: > 25 Copolar: > 25 Copolar: > 25 Copolar: > 25
Total power:> 20 Total power:> 20 Total power:> 22 Total power:> 22 Total power:> 22 Total power:> 22
0°
±60°
Typically: 25 dB Typically: 25 dB Typically: 25 dB Typically: 16 dB Typically: 18 dB Typically: 20 dB
> 10 dB
> 10 dB
> 10 dB
> 10 dB
> 10 dB
> 10 dB
Isolation: Intrasystem
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
< 1.5
> 30 dB
> 30 dB
> 30 dB
50 Ω
50 Ω
< 1.5
< 1.5
> 50 dB (806 – 960 // 1710 – 2170 MHz)
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
< –150 dBc
Max. power per input
250 W (at 50 °C ambient temperature)
200 W (at 50 °C ambient temperature)
806 – 960 +45°/ –45° Polarization
125°
65°
33°
dB
3
3
dB
10
10
0
0
Horizontal Pattern
Vertical Pattern
1710 –2170 +45°/ –45° Polarization
120°
60°
18°
3
0
Horizontal Pattern
102
3
dB
10
10
dB
XXPol Dual-b.
Isolation: Intersystem
> 30 dB
1710 – 2170
–45°
806 – 960
–45°
806 – 960
+45°
1710 – 2170
+45°
7-16
7-16
7-16
7-16
0
Vertical Pattern
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
Dual-band A-Panel
Dual Polarization
Half-power Beam Width
Fixed Electr. Downtilt
Integrated Combiner
806 – 960
1710 –2170
X
X
65°
60°
0°
0°
C
XXPol A-Panel 806–960/1710–2170 C 65°/ 60° 12/14dBi 0°/0°T
742 222
Type No.
Frequency range
806 –960
1710–2170
806 – 866 MHz 824 – 894 MHz 880 – 960 MHz 1710 – 1880 MHz1850 – 1990 MHz1920 – 2170 MHz
Polarization
+45°, –45°
+45°, –45°
+45°, –45°
+45°, –45°
+45°, –45°
+45°, –45°
Gain
2 x 11.5 dBi
2 x 11.8 dBi
2 x 12 dBi
2 x 13.5 dBi
2 x 13.7 dBi
2 x 14 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal: 68° Horizontal: 66° Horizontal: 64° Horizontal: 64° Horizontal: 60° Horizontal: 58°
Vertical:
34° Vertical:
33° Vertical:
32° Vertical: 18.5° Vertical: 17.5° Vertical: 17.3°
Front-to-back ratio
(180° ± 30°)
Cross polar ratio
Maindirection
Sector
[dB]
[dB]
Copolar: > 23 Copolar: > 23 Copolar: > 25 Copolar: > 25 Copolar: > 25 Copolar: > 25
Total power:> 20 Total power:> 20 Total power:> 22 Total power:> 22 Total power:> 22 Total power:> 22
0°
±60°
Typically: 20 dB Typically: 20 dB Typically: 20 dB Typically: 16 dB Typically: 18 dB Typically: 20 dB
> 10 dB
> 10 dB
> 10 dB
> 10 dB
> 10 dB
> 10 dB
Isolation: Intrasystem
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
< 1.5
> 30 dB
> 30 dB
> 30 dB
50 Ω
50 Ω
< 1.5
< 1.5
> 50 dB (806 – 960 // 1710 – 2170 MHz)
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
< –150 dBc
Max. power per input
250 W (at 50 °C ambient temperature)
200 W (at 50 °C ambient temperature)
Integrated combiner
XXPol Dual-b.
Isolation: Intersystem
> 30 dB
The insertion loss is included in the given antenna gain values.
806 – 960 +45°/ –45° Polarization
125°
65°
33°
dB
3
3
dB
10
10
0
0
Horizontal Pattern
Vertical Pattern
1710 –2170 +45°/ –45° Polarization
120°
60°
17.5°
dB
3
0
Horizontal Pattern
3
dB
10
10
806 – 960
–45°
1710 – 2170
–45°
0
806 – 960
+45°
1710 – 2170
+45°
C
C
7-16
7-16
Vertical Pattern
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
103
Dual-band A-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electr. Downtilt
824 – 960
1710 –2170
X
X
65°
65°
0°– 14°
0°– 8°
set by hand or by optional RCU (Remote Control Unit)
XXPol A-Panel 824–960/1710–2170 65°/ 65° 14/17dBi 0°–14°/0°–8°T
742 264
Type No.
Frequency range
824–960
824 – 894 MHz
870 – 960 MHz
Polarization
+45°, –45°
+45°, –45°
+45°, –45°
+45°, –45°
+45°, –45°
Gain
2 x 14 dBi
2 x 14 dBi
2 x 16.5 dBi
2 x 16.8 dBi
2 x 17 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal: 68°
Vertical:
16°
Horizontal: 65°
Vertical: 14.5°
Horizontal: 65°
Vertical:
7.8°
Horizontal: 65°
Vertical:
7.3°
Horizontal: 63°
Vertical:
6.8°
Electrical tilt
continuously adjustable
0°– 14°
0°– 14°
0°– 8°
0°– 8°
0°– 8°
Sidelobe suppression for
first sidelobe above horizon
0° ... 7° ... 14° T 0° ... 7° ... 14° T 0° ... 4° ... 8° T 0° ... 4° ... 8° T 0° ... 4° ... 8° T
14 ... 14 ... 13 dB 14 ... 14 ... 13 dB 14 ... 14 ... 14 dB 16 ... 16 ... 15 dB 15 ... 16 ... 15 dB
Front-to-back ratio, copolar
> 26 dB
> 26 dB
> 25 dB
> 25 dB
> 25 dB
Cross polar ratio
Maindirection
Sector
Typically:
20 dB
> 10 dB
Typically:
20 dB
> 10 dB
Typically:
16 dB
> 10 dB
Typically:
18 dB
> 10 dB
Typically:
20 dB
> 10 dB
> 30 dB
> 30 dB
> 30 dB
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
0°
±60°
Isolation: Intrasystem
Isolation: Intersystem
> 50 dB (824 – 960 // 1710 – 2170 MHz)
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
250 W
50 Ω
50 Ω
< 1.5
< 1.5
< –150 dBc
200 W
(at 50 °C ambient temperature)
824 – 960 +45°/ –45° Polarization
125°
65°
14.5°
3
dB
dB
3
1710 – 2170
–45°
824 – 960
–45°
824 – 960
+45°
1710 – 2170
+45°
7-16
7-16
7-16
7-16
10
10
0
0
Horizontal Pattern
Vertical Pattern
0°– 14° electrical downtilt
Mechanical specifications
Input
Adjustment
mechanism
120°
65°
10
0
Horizontal Pattern
104
3
Wind load
Max. wind velocity
dB
3
Bottom
2 x, Position bottom
continuously adjustable
Weight
7°
10
4 x 7-16 female
Connector position
1710 –2170 +45°/ –45° Polarization
dB
XXPol Dual-b.
1710–2170
1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz
0
16.5 kg
Frontal:
Lateral:
Rearside:
230 N (at 150 km/h)
180 N (at 150 km/h)
430 N (at 150 km/h)
200 km/h
Packing size
1615 x 302 x 192 mm
Height/width/depth
1316 / 262 / 139 mm
Vertical Pattern
0°– 8° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
Dual-band A-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electr. Downtilt
824 – 960
1710 –2170
X
X
65°
65°
0°–10°
0°– 6°
set by hand or by optional RCU (Remote Control Unit)
XXPol A-Panel 824–960/1710–2170 65°/ 65° 16/18.5dBi 0°–10°/0°–6°T
742 265
Type No.
Frequency range
824–960
824 – 894 MHz
880 – 960 MHz
1710–2170
1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz
Polarization
+45°, –45°
+45°, –45°
+45°, –45°
+45°, –45°
+45°, –45°
Gain
2 x 15.5 dBi
2 x 16 dBi
2 x 17.8 dBi
2 x 18.2 dBi
2 x 18.3 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal: 68°
Vertical: 10.5°
Horizontal: 65°
Vertical:
10°
Horizontal: 66°
Vertical:
5.2°
Horizontal: 65°
Vertical:
5.0°
Horizontal: 63°
Vertical:
4.7°
Electrical tilt
continuously adjustable
0.5°–9.5°
0.5°–9.5°
0°– 6°
0°– 6°
0°– 6°
Sidelobe suppression for
first sidelobe above horizon
0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T
16 ... 16 ... 17 dB 18 ... 18 ... 18 dB 14 ... 13 ... 13 dB 18 ... 17 ... 14 dB 18 ... 17 ... 14 dB
Front-to-back ratio, copolar
> 27 dB
> 25 dB
> 25 dB
> 25 dB
> 25 dB
Cross polar ratio
Maindirection
Sector
Typically:
20 dB
> 10 dB
Typically:
20 dB
> 10 dB
Typically:
16 dB
> 10 dB
Typically:
18 dB
> 10 dB
Typically:
18 dB
> 10 dB
> 30 dB
> 30 dB
> 30 dB
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
0°
±60°
Isolation: Intrasystem
> 50 dB (824 – 960 // 1710 – 2170 MHz)
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
250 W
50 Ω
50 Ω
< 1.5
< 1.5
XXPol Dual-b.
Isolation: Intersystem
< –150 dBc
200 W
(at 50 °C ambient temperature)
824 – 960 +45°/ –45° Polarization
125°
65°
10°
dB
3
3
1710 – 2170
–45°
824 – 960
–45°
824 – 960
+45°
1710 – 2170
+45°
7-16
7-16
7-16
7-16
dB
10
10
0
0
Horizontal Pattern
Vertical Pattern
0.5°–9.5° electrical downtilt
Input
1710 –2170 +45°/ –45° Polarization
120°
Mechanical specifications
4 x 7-16 female
Connector position
Adjustment
mechanism
65°
Bottom
2x, Position bottom
continuously adjustable
Weight
5°
dB
0
Horizontal Pattern
3
dB
10
10
3
Wind load
0
Vertical Pattern
0°– 6° electrical downtilt
Max. wind velocity
23 kg
Frontal:
Lateral:
Rearside:
340 N (at 150 km/h)
280 N (at 150 km/h)
640 N (at 150 km/h)
200 km/h
Packing size
2215 x 302 x 192 mm
Height/width/depth
1916 / 262 / 139 mm
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
105
Dual-band A-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electr. Downtilt
824 – 960
1710 –2170
X
X
65°
65°
0°–7°
0°– 6°
set by hand or by optional RCU (Remote Control Unit)
XXPol A-Panel 824–960/1710–2170 65°/ 65° 17/18.5dBi 0°–7°/0°–6°T
742 266
Type No.
Frequency range
824–960
824 – 894 MHz
880 – 960 MHz
Polarization
+45°, –45°
+45°, –45°
+45°, –45°
+45°, –45°
+45°, –45°
Gain
2 x 16.5 dBi
2 x 17 dBi
2 x 17.8 dBi
2 x 18.2 dBi
2 x 18.5 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal: 68°
Vertical:
8.1°
Horizontal: 65°
Vertical:
7.5°
Horizontal: 66°
Vertical:
5.2°
Horizontal: 65°
Vertical:
5.0°
Horizontal: 63°
Vertical:
4.7°
Electrical tilt
continuously adjustable
0.5°–7°
0.5°–7°
0°– 6°
0°– 6°
0°– 6°
Sidelobe suppression for
first sidelobe above horizon
0° ... 4° ... 7° T 0° ... 4° ... 7° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T
16 ... 16 ... 14 dB 16 ... 16 ... 14 dB 13 ... 13 ... 13 dB 16 ... 15 ... 14 dB 15 ... 15 ... 15 dB
Front-to-back ratio, copolar
> 28 dB
> 28 dB
> 25 dB
> 25 dB
> 25 dB
Cross polar ratio
Maindirection
Sector
Typically:
20 dB
> 10 dB
Typically:
20 dB
> 10 dB
Typically:
16 dB
> 10 dB
Typically:
18 dB
> 10 dB
Typically:
20 dB
> 10 dB
> 30 dB
> 30 dB
> 30 dB
> 30 dB
> 30 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
0°
±60°
Isolation: Intrasystem
Isolation: Intersystem
> 50 dB (824–960 // 1710–2170 MHz)
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
250 W
50 Ω
50 Ω
< 1.5
< 1.5
< –150 dBc
200 W
(at 50 °C ambient temperature)
824 – 960 +45°/ –45° Polarization
125°
65°
7.5°
dB
3
3
1710 – 2170
–45°
824 – 960
–45°
824 – 960
+45°
1710 – 2170
+45°
7-16
7-16
7-16
7-16
dB
10
10
0
0
Horizontal Pattern
Vertical Pattern
0.5°–7° electrical downtilt
120°
Mechanical specifications
Input
1710 –2170 +45°/ –45° Polarization
4 x 7-16 female
Connector position
Adjustment
mechanism
65°
Bottom
2x, Position bottom
continuously adjustable
Weight
5°
0
Horizontal Pattern
106
3
dB
3
Wind load
10
10
dB
XXPol Dual-b.
1710–2170
1710 – 1880 MHz 1850 – 1990 MHz 1900 – 2170 MHz
0
Vertical Pattern
0°– 6° electrical downtilt
Max. wind velocity
26 kg
Frontal:
Lateral:
Rearside:
460 N (at 150 km/h)
380 N (at 150 km/h)
860 N (at 150 km/h)
200 km/h
Packing size
2815 x 302 x 192 mm
Height/width/depth
2516 / 262 / 139 mm
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
Summary – Directional Antennas
Triple-band
UMTS
Dual Polarization + 45°/ –45° – 800/900 1800/1900 2000
Type
Type No.
Height
[mm]
Page
XXXPol A-Panel
806– 960
1710–1880
1920–2170
66°
66°
65°
15dBi
16.5dBi
17dBi
0°–12°T
0°–8°T
0°–8°T
742 270
1498
108
XXXPol A-Panel
806– 960
1710–1880
1920–2170
67°
65°
65°
16.5dBi
17.5dBi
18dBi
0°–10°T
0°–6°T
0°–6°T
742 271
2058
109
XXXPol A-Panel
806– 960
1710–1880
1920–2170
66°
67°
65°
17.5dBi
17.5dBi
18dBi
0°–7°T
0°–6°T
0°–6°T
742 272
2628
110
XXXPol A-Panel
824– 960
1710–2170
1710–2170
65°
65°
65°
17dBi
17dBi
16.5dBi
0°–7°T
0°–8°T
0°–8°T
742 241
2628
111
New Products
UMTS
XXXPol
Connector position: Bottom
107
Triple-band A-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electr. Downtilt
806 – 960 1710 –1880 1920 –2170
X
X
X
66°
66°
65°
0°– 1 2 °
0°– 8°
0°– 8°
set by hand or by optional RCU (Remote Control Unit)
XXXPol A-Panel 806–960/1710–1880/1920–2170 66°/ 66°/65° 15/16.5/17dBi 0°–12°/0°–8°/0°–8°T
742 270
Type No.
Frequency range
806 –960
1710 –1880
824 – 894 MHz
Polarization
+45°, –45°
+45°, –45°
+45°, –45°
+45°, –45°
+45°, –45°
Gain
2 x 14.8 dBi
2 x 15 dBi
2 x 15.2 dBi
2 x 16.5 dBi
2 x 17.2 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal: 69°
Vertical: 14.3°
Horizontal: 68°
Vertical:
14°
Horizontal: 66°
Vertical: 13.3°
Horizontal: 66°
Vertical:
7.1°
Horizontal: 65°
Vertical:
6.5°
Electrical tilt
continuously adjustable
0.5°– 12°
0.5°– 12°
0.5°– 12°
0.5°– 8°
0°– 8°
Sidelobe suppression for
first sidelobe above horizon
880 – 960 MHz
1920 –2170
806 – 866 MHz
1710 – 1880 MHz 1920 – 2170 MHz
0° ... 6° ... 12° T 0° ... 6° ... 12° T 0° ... 6° ... 12° T 0° ... 4° ... 8° T 0° ... 4° ... 8° T
13 ... 12 ... 10 dB 14 ... 14 ... 14 dB 16 ... 16 ... 16 dB 17 ... 16 ... 15 dB 17 ... 15 ... 13 dB
Front-to-back ratio, copolar
> 27 dB
> 27 dB
> 27 dB
> 23 dB
> 23 dB
Cross polar ratio
Maindirection
Sector
Typically:
25 dB
> 10 dB
Typically:
25 dB
> 10 dB
Typically:
25 dB
> 10 dB
Typically:
18 dB
> 10 dB
Typically:
20 dB
> 10dB
> 30 dB
> 30 dB
> 30 dB
> 30 dB
> 30 dB
0°
±60°
Isolation: Intrasystem
Isolation: Intersystem
> 50 dB (806 – 960 // 1710 – 1880 MHz)11
> 50 dB (806 – 960 // 1920 – 2170 MHz)11
> 30 dB (1710 – 1880 // 1920 – 2170 MHz)
Impedance
50 Ω
VSWR
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
50 Ω
50 Ω
< 1.5
< 1.5
50 Ω
< –150 dBc
Max. power per input
50 Ω
< 1.5
< 1.5
< –150 dBc
< –150 dBc
250 W
200 W
(at 50 °C ambient temperature)
200 W
806 – 960 +45°/ –45° Polarization
130°
66°
14°
10
3
dB
3
dB
10
0
0
Horizontal Pattern
1710 –1880 1710 –1880
+45°
–45°
66°
7.1°
Input
0
0
Horizontal Pattern
7-16
7-16 7-16
Vertical Pattern
0.5°– 8° electrical downtilt
1920 –2170 +45°/ –45° Polarization
Connector position
Adjustment
mechanism
Wind load
65°
6.5°
0
Horizontal Pattern
108
3
dB
dB
3
Max. wind velocity
10
10
7-16
6 x 7-16 female
Bottom
3 x, Position bottom
continuously adjustable
Weight
120°
7-16
dB
dB
3
7-16
Mechanical specifications
10
10
3
806 – 960
+45°
1920 – 2170 1920 – 2170
+45°
–45°
1710 –1880 +45°/ –45° Polarization
125°
806 – 960
–45°
Vertical Pattern
0.5°– 12° electrical downtilt
0
25 kg
Frontal:
Lateral:
Rearside:
260 N (at 150 km/h)
210 N (at 150 km/h)
580 N (at 150 km/h)
200 km/h
Packing size
1819 x 304 x 204 mm
Height/width/depth
1498 / 262 / 149 mm
Vertical Pattern
0°– 8° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
Triple-band A-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electr. Downtilt
806– 960 1710 –1880 1920 –2170
X
X
X
67°
65°
65°
0°– 10°
0°– 6°
0°– 6°
set by hand or by optional RCU (Remote Control Unit)
XXXPol A-Panel 806–960/1710–1880/1920–2170 67°/ 65°/65° 16.5/17.5/18dBi 0°–10°/0°–6°/0°–6°T
742 271
Type No.
Frequency range
806–960
806– 866 MHz
824– 894 MHz
1710–1880
880– 960 MHz
1920–2170
1710 – 1880 MHz 1920 – 2170 MHz
Polarization
+45°, –45°
+45°, –45°
+45°, –45°
+45°, –45°
Gain
2 x 16 dBi
2 x 16.1 dBi
2 x 16.3 dB
2 x 17.5 dBi
2 x 18 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal: 69°
Vertical:
11°
Horizontal: 68°
Vertical: 10.7°
Horizontal: 67°
Vertical:
9.8°
Horizontal: 65°
Vertical:
5.1°
Horizontal: 65°
Vertical:
4.8°
Electrical tilt
continuously adjustable
0°– 10°
0°– 10°
0°– 10°
0°– 6°
0°– 6°
Sidelobe suppression for
first sidelobe above horizon
+45°, –45°
0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 3° ... 6° T
0° ... 3° ... 6° T
15 ... 15 ... 13 dB 15 ... 15 ... 13 dB 15 ... 15 ... 13 dB 14 ... 15 ... 16 dB 14 ... 14 ... 14 dB
Front-to-back ratio, copolar
> 25 dB
> 25 dB
> 25 dB
> 24 dB
> 25 dB
Cross polar ratio
Maindirection
Sector
Typically:
25 dB
> 10 dB
Typically:
25 dB
> 10 dB
Typically:
25 dB
> 10 dB
Typically:
18 dB
> 10 dB
Typically:
20 dB
> 10 dB
Isolation: Intrasystem
> 30 dB
> 30 dB
> 30 dB
> 30 dB
> 30 dB
Isolation: Intersystem
> 50 dB (806– 960 // 1710 – 1880 MHz)11
> 50 dB (806– 960 // 1920 – 2170 MHz)11
> 30 dB (1710 – 1880 // 1920 – 2170 MHz)
Impedance
50 Ω
VSWR
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
50 Ω
50 Ω
< 1.5
< 1.5
50 Ω
< –150 dBc
Max. power per input
50 Ω
< 1.5
< 1.5
< –150 dBc
< –150 dBc
250 W
200 W
(at 50 °C ambient temperature)
200 W
806– 960 +45°/ –45° Polarization
67°
XXXPol
130°
10°
dB
3
3
dB
10
10
806– 960
–45°
0
0
Horizontal Pattern
Vertical Pattern
0°– 10° electrical downtilt
806– 960
+45°
1920 –2170 1920 –2170
+45°
–45°
1710 –1880 1710 –1880
+45°
–45°
1710 –1880 +45°/ –45° Polarization
125°
7-16
65°
7-16
7-16 7-16
7-16
7-16
5.1°
Mechanical specifications
10
3
Input
dB
3
dB
10
0
Horizontal Pattern
Vertical Pattern
0°– 6° electrical downtilt
Adjustment
mechanism
Wind load
65°
4.8°
dB
3
0
Horizontal Pattern
3
dB
10
10
Bottom
3 x, Position bottom
continuously adjustable
Weight
1920 –2170 +45°/ –45° Polarization
120°
6 x 7-16 female
Connector position
0
Max. wind velocity
33 kg
Frontal:
Lateral:
Rearside:
370 N (at 150 km/h)
300 N (at 150 km/h)
820 N (at 150 km/h)
200 km/h
Packing size
2379 x 304 x 204 mm
Height/width/depth
2058 / 262 / 149 mm
0
Vertical Pattern
0°– 6° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
109
Triple-band A-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electr. Downtilt
806– 960 1710 –1880 1920 –2170
X
X
X
66°
67°
65°
0°–7°
0°– 6°
0°– 6°
set by hand or by optional RCU (Remote Control Unit)
XXXPol A-Panel 806–960/1710–1880/1920–2170 66°/ 67°/65° 17.5/17.5/18dBi 0°–7°/0°–6°/0°–6°T
742 272
Type No.
Frequency range
806–960
806– 866 MHz
824– 894 MHz
1710–1880
880– 960 MHz
1920–2170
1710 – 1880 MHz 1920 – 2170 MHz
Polarization
+45°, –45°
+45°, –45°
+45°, –45°
+45°, –45°
Gain
2 x 17 dBi
2 x 17.2 dBi
2 x 17.5 dBi
2 x 17.5 dBi
2 x 18 dBi
Half-power beam width
Copolar +45°/ –45°
Horizontal: 69°
Vertical: 7.8°
Horizontal: 68°
Vertical: 7.4°
Horizontal 66°
Vertical: 7°
Horizontal: 67°
Vertical: 5.2°
Horizontal: 65°
Vertical: 4.8°
Electrical tilt
continuously adjustable
0.5°– 7°
0.5°– 7°
0.5°– 7°
0°– 6°
0°– 6°
Sidelobe suppression for
first sidelobe above horizon
+45°, –45°
0° ... 4° ... 7° T 0° ... 4° ... 7° T 0° ... 4° ... 7° T 0° ... 3° ... 6° T
0° ... 3° ... 6° T
15 ... 15 ... 14 dB 15 ... 15 ... 14 dB 15 ... 15 ... 15 dB 14 ... 14 ... 14 dB 14 ... 14 ... 14 dB
Front-to-back ratio, copolar
> 25 dB
> 25 dB
> 25 dB
> 25 dB
> 25 dB
Cross polar ratio
Maindirection
Sector
Typically:
25 dB
> 10 dB
Typically:
25 dB
> 10 dB
Typically:
25 dB
> 10 dB
Typically:
18 dB
> 10 dB
Typically:
20 dB
> 10 dB
Isolation: Intrasystem
> 30 dB
> 30 dB
> 30 dB
> 30 dB
> 30 dB
Isolation: Intersystem
> 50 dB (806– 960 // 1710 – 1880 MHz)11
> 50 dB (806– 960 // 1920 – 2170 MHz)11
> 30 dB (1710 – 1880 // 1920 – 2170 MHz)
Impedance
50 Ω
VSWR
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
50 Ω
50 Ω
< 1.5
< 1.5
50 Ω
< –150 dBc
Max. power per input
50 Ω
< 1.5
< 1.5
< –150 dBc
< –150 dBc
250 W
200 W
(at 50 °C ambient temperature)
200 W
XXXPol
806– 960 +45°/ –45° Polarization
130°
66°
7.5°
dB
3
3
dB
10
10
806– 960
–45°
0
0
Horizontal Pattern
Vertical Pattern
0.5°–7° electrical downtilt
1710 –1880 +45°/ –45° Polarization
125°
67°
806– 960
+45°
1920 –2170 1920 –2170
+45°
–45°
7-16
7-16
1710 –1880 1710 –1880
+45°
–45°
7-16 7-16
7-16
7-16
5.2°
Mechanical specifications
10
3
Input
dB
3
dB
10
Connector position
0
0
Horizontal Pattern
Vertical Pattern
0°– 6° electrical downtilt
Adjustment
mechanism
Weight
1920 –2170 +45°/ –45° Polarization
Wind load
120°
65°
4.8°
dB
3
0
Horizontal Pattern
110
3
dB
10
10
Max. wind velocity
6 x 7-16 female
Bottom
3 x, Position bottom
continuously adjustable
40 kg
Frontal:
480 N (at 150 km/h)
Lateral:
390 N (at 150 km/h)
Rearside: 1060 N (at 150 km/h)
200 km/h
Packing size
2949 x 304 x 204 mm
Height/width/depth
2628 / 262 / 149 mm
0
Vertical Pattern
0°– 6° electrical downtilt
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
Triple-multiband A-Panel
Dual Polarization
Half-power Beam Width
Adjust. Electr. Downtilt
824 – 960 1710 –2170 1710 –2170
X
X
X
65°
65°
65°
0°–7°
0°– 8°
0°– 8°
set by hand or by optional RCU (Remote Control Unit)
XXXPol A-Panel 824–960/1710–2170/1710–2170 65°/ 65°/65° 17/17/16.5dBi 0°–7°/0°–8°/0°–8°T
742 241
Type No.
Frequency range
824–960
824 – 894 MHz
880 – 960 MHz
+45°, –45°
+45°, –45°
2 x 16.5 dBi
2 x 17 dBi
Polarization
Gain: 824–960 MHz
1710–2170 MHz (Syst. 1)
1710–2170 MHz (Syst. 2)
Half-power beam width
Horizontal: 68°
Copolar +45°/ –45°
Vertical:
8.1°
Electrical tilt
0.5°–7°
continuously adjustable
Sidelobe suppression for
0° ... 4° ... 7° T
first sidelobe above horizon 16 ... 16 ... 14 dB
Front-to-back ratio, copolar
> 26 dB
Cross polar ratio
Typically:
Maindirection
0°
20 dB
Sector
±60°
> 10 dB
Isolation: Intrasystem
> 30 dB
Isolation: Intersystem
Horizontal: 65°
Vertical:
7.5°
0.5°–7°
1710–2170 1710–2170
1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz
+45°, –45°
+45°, –45°
+45°, –45°
2 x 16.5 dBi
2 x 16 dBi
Horizontal: 65°
Vertical:
7.8°
0°– 8°
2 x 16.8 dBi
2 x 16.3 dBi
Horizontal: 65°
Vertical:
7.3°
0°– 8°
2 x 17 dBi
2 x 16.5 dBi
Horizontal: 63°
Vertical:
6.8°
0°– 8°
0° ... 4° ... 7° T 0° ... 4° ... 8° T 0° ... 4° ... 8° T 0° ... 4° ... 8° T
16 ... 16 ... 14 dB 14 ... 14 ... 14 dB 16 ... 16 ... 15 dB 15 ... 16 ... 15 dB
> 26 dB
> 25 dB
> 25 dB
> 25 dB
Typically:
Typically:
Typically:
Typically:
20 dB
16 dB
18 dB
20 dB
> 10 dB
> 10 dB
> 10 dB
> 10 dB
> 30 dB
> 30 dB
> 30 dB
> 30 dB
> 50 dB (824 – 960 // 1710 – 2170 MHz)11
> 38 dB (1710 – 2170 // 1710 – 2170 MHz)
50 Ω
50 Ω
50 Ω
50 Ω
50 Ω
< 1.5
< 1.5
< 1.5
< 1.5
< 1.5
< –150 dBc
< –150 dBc
Impedance
VSWR
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power per input
250 W
200 W
(at 50 °C ambient temperature)
824 – 960 +45°/ –45° Polarization
65°
XXXPol
125°
7.5°
dB
3
3
dB
10
10
824 – 960
–45°
0
0
Horizontal Pattern
Vertical Pattern
0.5°–7° electrical downtilt
1710 –1880 +45°/ –45° Polarization
125°
1710 – 2170 1710 – 2170
+45°
–45°
824 – 960
+45°
1710 – 2170 1710 –2170
+45°
–45°
65°
7-16
7-16
7-16 7-16
7-16
7-16
7.8°
Mechanical specifications
10
3
Input
dB
3
dB
10
Connector position
0
0
Horizontal Pattern
Vertical Pattern
0°– 8° electrical downtilt
Adjustment
mechanism
Weight
1920 –2170 +45°/ –45° Polarization
Wind load
115°
63°
6.8°
0
dB
3
3
dB
10
10
Max. wind velocity
6 x 7-16 female
Bottom
3 x, Position bottom
continuously adjustable
34 kg
Frontal:
480 N (at 150 km/h)
Lateral:
390 N (at 150 km/h)
Rearside: 1060 N (at 150 km/h)
200 km/h
Packing size
2944 x 304 x 204 mm
Height/width/depth
2628 / 262 / 149 mm
0
Mounting accessories are not included in the scope of delivery (see page 186 – 191)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
111
112
Summary – Directional Antennas
Vertical Polarization
Single-band and Multi-band – UMTS
Vertical Polarization
Type
Height
[mm]
Page
824–960/1710–2170
824–960/1710–2170
65°
65°
5dBi
5dBi
738 445
738 446
310
310
114
114
VPol LogPer
806–2170
65°
11dBi
742 192
300
115
VPol F-Panel
1920–2170
60°
17.5dBi
741 415
982
116
Vpol F-Panel
1710–2170
65°
18dBi
742 445
1302
117
VVPol F-Panel
824–960
1710–2170
C
90°
90°
7dBi
7dBi
742 290
328
118
VVPol F-Panel
824–960
1710–2170
C
90°
90°
10dBi
11.5dBi
800 10046
662
119
120°
14.5dBi
741 786
982
120
VPol F-Panel
1920–210
0°–10°T
New Products
UMTS
VPol
VPol BiDir
VPol BiDir
Type No.
113
Multi-band Bidirectional Antenna
Vertical Polarization
Half-power Beam Width
824 – 960/1710 –2170
V
65°
VPol BiDir 824–960/1710–2170 65° 5dBi
Type No.
738 445
738 446
Input
1 x 7-16 female
1 x N female
Frequency range
824 – 960 MHz, 1710 – 2170 MHz
< 1.5
824 – 960 MHz: 5 dBi
1710 – 1880 MHz: 5.5 dBi
1880 – 2170 MHz: 6.5 dBi
Impedance
50 Ω
Polarization
Vertical
Max. power (total)
200 W (at 50 °C ambient temperature)
Weight
0.8 kg
Wind load
Frontal:
Lateral:
Rearside:
Max. wind velocity
25 N (at 150 km/h)
65 N (at 150 km/h)
35 N (at 150 km/h)
200 km/h
Packing size
422 x 212 x 95 mm
Height/width/depth
310 / 55 / 190 mm
Material:
Radiator: Tin plated copper.
Reflector: Weather-proof aluminum.
Radome: High impact plastic, colour: Grey.
All screws and nuts: Stainless steel.
Mounting:
Wall mounting: No additional mounting kit
needed.
For pipe mast mounting use clamps listed on the
datasheet (order separately).
Ice protection:
The radiating system is protected by the radome.
Due to its very sturdy construction, the antenna
remains operational even under icy conditions.
Grounding:
All metal parts of the antenna as well as the
inner conductor are DC grounded.
3
dB
10
0
Typical Horizontal Pattern
114
372 mm
Gain
8.5 mm
400 mm
VSWR
Logarithmic Periodic
Vertical Polarization
Half-power Beam Width
806 – 2170
V
65°
VPol LogPer 806–2170 65° 11dBi
Type No.
742 192
Input
1 x 7-16 female
Connector position
Bottom
Frequency range
806 – 1000 MHz
1000 – 1700 MHz
1700 – 2170 MHz
VSWR
< 1.5
< 1.5
< 1.5
Gain
11 dBi
11.3 dBi
11.5 dBi
50 Ω
50 Ω
50 Ω
Impedance
Polarization
Vertical
Vertical
Vertical
Front-to-back ratio
> 25 dB
> 25 dB
> 23 dB
65°
55°
55°
50°
50°
45°
< –150 dBc
< –150 dBc
< –150 dBc
Half-power Beam Width
horizontal
vertical
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power
300 W
250 W
200 W
(at 50 °C ambient temperature)
Weight
5.7 kg
Wind load
Frontal:
Lateral:
Rearside:
Max. wind velocity
20 N (at 150 km/h)
260 N (at 150 km/h)
30 N (at 150 km/h)
200 km/h
Packing size
360 x 175 x 1000 mm
300 / 155 / 785 mm
Material:
Radiator: Weather-proof aluminum.
Reflector screen: Weather-proof aluminum.
Radome: Fiberglass, colour: Grey.
All screws and nuts: Stainless steel.
Mounting:
The antenna can be mounted on tubular mast with a
diameter of 30 – 70 mm with supplied clamps.
Ice protection:
Due to the very sturdy antenna construction and the
protection of the radiating system by the radome, the
antenna remains operational even under icy conditions.
Grounding:
All metal parts of the antenna as well as the inner
conductor are DC grounded.
VPol
Height/width/depth
806 – 1000 MHz
1700 – 2170 MHz
0
Horizontal Pattern
0
Vertical Pattern
3
45°
10
dB
3
10
dB
3
10
dB
10
50°
55°
0
Horizontal Pattern
3
dB
65°
0
Vertical Pattern
115
F-Panel
Vertical Polarization
Half-power Beam Width
1920 –2170
V
60°
VPol F-Panel 1920–2170 60° 17.5dBi
741 415
Type No.
Frequency range
1920 – 2170 MHz
Polarization
Vertical
Gain
17.5 dBi
Half-power beam width
H-plane: 60°
E-plane: 8°
Front-to-back ratio
> 25 dB
Impedance
50 Ω
VSWR
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power
200 W (at 50 °C ambient temperature)
60°
VPol
110°
3
dB
10
0
Horizontal Pattern
Mechanical specifications
Input
Connector position*
7-16 female
Bottom or top
Weight
8°
Wind load
3
dB
10
0
Vertical Pattern
Max. wind velocity
Packing size
Height/width/depth
3.7 kg
Frontal:
Lateral:
Rearside:
190 N (at 150 km/h)
40 N (at 150 km/h)
230 N (at 150 km/h)
200 km/h
1084 x 172 x 62 mm
982 / 155 / 36 mm
* Inverted mounting:
Connector position top: Change drain hole screw.
116
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
Multi-band F-Panel
Vertical Polarization
Half-power Beam Width
Adjust. Electrical Downtilt
1710 –2170
V
65°
0°– 10°
set by hand or by optional RCU (Remote Control Unit)
VPol F-Panel 1710–2170 65° 18dBi 0°–10°T
742 445
Type No.
Frequency range
1710 – 1880 MHz
1710–2170
1850 – 1990 MHz
1920 – 2170 MHz
Polarization
Vertical
Vertical
Vertical
Gain
17.5 dBi
17.9 dBi
18.1 dBi
Horizontal: 65°
Vertical:
6.7°
Horizontal: 63°
Vertical:
6.5°
Half-power beam width
Horizontal:
Vertical:
Electrical tilt
68°
7°
0°– 10°
0°– 10°
0°– 10°
continuously adjustable continuously adjustable continuously adjustable
Sidelobe suppression for
first sidelobe above horizon
Front-to-back ratio
0° ... 5° ... 10° T
18 ... 16 .... 13 dB
0° ... 5° ... 10° T
18 ... 17 ... 14 dB
0° ... 5° ... 10° T
18 ... 17 ... 14 dB
> 25 dB
> 25 dB
> 25 dB
Impedance
50 Ω
50 Ω
50 Ω
VSWR
< 1.5
< 1.5
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power
300 W (at 50 °C ambient temperature)
1710 – 1880 MHz
130°
68°
7°
dB
3
3
dB
10
10
0
0
Vertical Pattern
0°– 10° electrical downtilt
continuously adjustable
1710 – 2170
VPol
1850 – 1990 MHz
125°
65°
7-16
6.7°
10
3
Mechanical specifications
dB
dB
10
3
VPol
Horizontal Pattern
Input
0
1 x 7-16 female
0
Horizontal Pattern
Vertical Pattern
0°– 10° electrical downtilt
continuously adjustable
1920 – 2170 MHz
Connector position
Adjustment
mechanism
63°
6.5°
Max. wind velocity
dB
3
0
Horizontal Pattern
3
dB
10
10
1x, Position bottom
continuously adjustable
Weight
Wind load
120°
Bottom
6.8 kg
Frontal:
Lateral:
Rearside:
130 N (at 150 km/h)
110 N (at 150 km/h)
310 N (at 150 km/h)
200 km/h
Packing size
1574 x 172 x 92 mm
Height/width/depth
1302 / 155 / 69 mm
0
Vertical Pattern
0°– 10° electrical downtilt
continuously adjustable
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 – 160
117
Dual-band F-Panel
Vertical Polarization
Half-power Beam Width
Integrated Combiner
824 – 960
1710 –2170
V
V
90°
82°
C
VVPol F-Panel 824–960/1710–2170 C 90°/82° 7/7dBi
742 290
Type No.
Frequency range
Polarization
824 – 960 MHz
1710 – 2170 MHz
Vertical
Vertical
Gain
7 dBi
Half-power beam width
Front-to-back ratio
Horizontal:
Vertical:
Horizontal:
Vertical:
> 18 dB
> 20 dB
50 Ω
50 Ω
Impedance
VSWR
7 dBi
90°
60°
82°
70°
< 1.7 (824 – 960 MHz) < 1.7 (1710 – 2170 MHz)
< 1.5 (870 – 960 MHz) < 1.5 (1710 – 1990 MHz)
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power
< –150 dBc
< –150 dBc
100 W (at 50 °C ambient temperature)
824 – 960
824 – 960
VPol
90°
VPol
1710 – 2170
VPol
60°
180°
C
7-16
10
3
dB
3
dB
10
0
0
Horizontal Pattern
Vertical Pattern
Mechanical specifications
1710 –2170
Input
82°
70°
170°
Max. wind velocity
10
0
Horizontal Pattern
118
3
dB
dB
10
Bottom
Weight
Wind load
3
1 x 7-16 female
Connector position
2.5 kg
Frontal:
Lateral:
Rearside:
30 N (at 150 km/h)
25 N (at 150 km/h)
70 N (at 150 km/h)
200 km/h
Packing size
444 x 172 x 92 mm
Height/width/depth
328 / 155 / 69 mm
0
Vertical Pattern
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
Dual-band F-Panel
Vertical Polarization
Half-power Beam Width
Integrated Combiner
824 – 960
1710 –2170
V
V
90°
82°
C
VVPol F-Panel 824–960/1710–2170 C 90°/82° 10/11dBi
800 10046
Type No.
Frequency range
Polarization
Gain
824 – 960 MHz
1710 – 2170 MHz
Vertical
Vertical
10 dBi
Half-power beam width
Front-to-back ratio
Horizontal:
Vertical:
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power
Horizontal:
Vertical:
> 18 dB
82°
19°
> 20 dB
50 Ω
50 Ω
< 1.7 (824 – 960 MHz)
< 1.5 (870 – 960 MHz)
< 1.5
< –150 dBc
< –150 dBc
Impedance
VSWR
11 dBi
90°
33°
100 W (at 50 °C ambient temperature)
824 – 960
824 – 960
VPol
90°
1710 – 2170
VPol
VPol
180°
C
33°
7-16
10
3
dB
3
dB
10
0
0
Horizontal Pattern
Vertical Pattern
Mechanical specifications
1710 –2170
Input
82°
Bottom
Weight
170°
Wind load
19°
Max. wind velocity
10
0
Horizontal Pattern
3
dB
dB
10
3
1 x 7-16 female
Connector position
4.4 kg
Frontal:
Lateral:
Rearside:
65 N (at 150 km/h)
50 N (at 150 km/h)
160 N (at 150 km/h)
200 km/h
Packing size
744 x 172 x 92 mm
Height/width/depth
662 / 155 / 69 mm
0
Vertical Pattern
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
119
F-Panel
Vertical Polarization
Half-power Beam Width
1920 –2170
V
120°
VPol F-Panel 1920–2170 120° 14.5dBi
741 786
Type No.
Frequency range
1920 – 2170 MHz
Polarization
Vertical
Gain
14.5 dBi
Half-power beam width
H-plane: 120°
E-plane: 8°
Front-to-back ratio
> 18 dB
Impedance
50 Ω
VSWR
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power
200 W (at 50 °C ambient temperature)
120°
VPol
215°
3
dB
10
0
Horizontal Pattern
Mechanical specifications
Input
Connector position*
7-16 female
Bottom or top
Weight
8°
Wind load
3
dB
10
0
Vertical Pattern
Max. wind velocity
Packing size
Height/width/depth
3.7 kg
Frontal:
Lateral:
Rearside:
180 N (at 150 km/h)
80 N (at 150 km/h)
230 N (at 150 km/h)
200 km/h
1084 x 172 x 72 mm
982 / 155 / 49 mm
* Inverted mounting:
Connector position top: Change drain hole screw.
120
Mounting accessories are not included in the scope of delivery (see page 194 – 197)
Summary – Omnidirectional Antennas
800/900/1800/2000
Vertical Polarization – 800/900
Type
Type No.
Connector Height
female
[mm]
Remarks
Page
VPol Omni
VPol Omni
870–960
806–960
360°
360°
2 dBi
2 dBi
738 450
K 75 11 61
N
N
180
273
indoor/outdoor 122
123
VPol Omni
890–960
360°
5 dBi
K 75 15 64 1
N
635
124
VPol Omni
870–960
360°
8 dBi
736 350
7-16
1543
125
VPol Omni
806–894
360°
11 dBi
738 192
7-16
3237
126
VPol Omni
870–960
360°
11 dBi
736 347
7-16
3033
127
VPol Omni
870–960
360° 10.5 dBi
736 349
7-16
2954
128
5°T
Vertical Polarization – Dual-band
VPol Omni
870–960/1710–1880 360°
2 dBi
738 449
N
216
indoor/outdoor 129
VPol Omni
824–960/1805–2170 360°
2 dBi
800 10147
N
216
indoor/outdoor 130
VVPol Omni 870–960/1710–1880 360°
870–960/1710–1880 360°
2 dBi
2 dBi
741 862
N
493
seperate
inputs
131
VVPol Omni 870–960/1710–1880 360°
1920–2170 360°
2 dBi
2 dBi
800 10111
N
493
seperate
inputs
132
739 785
7-16
800
133
738 187
737 190
7-16
7-16
1570
1560
134
135
VPol Omni
1710–1880
360°
8 dBi
VPol Omni
VPol Omni
1710–1880
1710–1880
360°
360°
11 dBi
11 dBi
6°T
Vertical Polarization – 1800/2000
VPol Omni
1710–2170
360°
2 dBi
738 454
N
115
indoor/outdoor 136
VPol Omni
1920–2170
360°
11 dBi
741 790
7-16
1387
137
121
Omni
VPol
Vertical Polarization – 1800
Omnidirectional Antenna
Vertical Polarization
Indoor and outdoor use
870 – 960
V
VPol Omni 870–960 360° 2dBi
738 450
Type No.
Input
N female
Connector position
Bottom or top
Frequency range
870 – 960 MHz
VSWR
< 1.5
Gain
2 dBi
Impedance
50 Ω
< –150 dBc
Polarization
Vertical
Max. power
100 Watt (at 50 °C ambient temperature)
Weight
200 g
Radome diameter
20 mm
Height
180 mm
Material:
Radiator: Brass.
Radome: Fiberglass, colour: White.
Mounting:
One hole mounting (16 mm diameter) to surfaces
of max. 10 mm thickness.
Grounding:
All metal parts of the antenna as well as
the inner conductor and the mounting kit
are DC grounded.
78°
3
dB
10
0
Vertical Pattern
122
180 mm
Intermodulation IM3
(2 x 43 dBm carrier)
Omnidirectional Antennas
Vertical Polarization
806 – 960
V
VPol Omni 806–960 360° 2dBi
K 75 11 61
Type No.
Frequency range
806 – 960 MHz
Vertical
Gain
2 dBi
Impedance
50 Ω
VSWR
348 mm
Polarization
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power
100 W (at 50 °C ambient temperature)
Mounting:
The antenna can be attached in two ways with
the supplied mounting kit:
1. On the tip of a tubular mast of 40 – 54 mm
diameter (connecting cable runs inside the
mast).
2. Laterally at the tip of a tubular mast of
20 – 54 mm diameter (connecting cable runs
outside the mast).
Material:
Radiator: Brass.
Radome: Fiberglass, colour: Grey.
Base: Weather-proof aluminum.
Mounting kit, screws and nuts: Stainless steel.
Grounding:
All metal parts of the antenna as well as
the inner conductor and the mounting kit
are DC grounded.
78°
dB
3
VPol
10
0
Vertical Pattern
Mechanical specifications
Input
Connector position
Bottom
Weight
0.74 kg
Radome diameter
Wind load
Max. wind velocity
Packing size
On the tip
Laterally at the tip
Brackets for side mounting (see page 198 – 200)
N female
Height
21 mm
17 N (at 150 km/h)
200 km/h
455 x 112x 97 mm
348 mm
123
Omnidirectional Antennas
Vertical Polarization
890 – 960
V
VPol Omni 890–960 360° 5dBi
K 75 15 64 1
Type No.
Frequency range
890 – 960 MHz
Polarization
Vertical
Gain
5 dBi
Impedance
50 Ω
VSWR
< 1.5
< –150 dBc
Max. power
715 mm
Intermodulation IM3
(2 x 43 dBm carrier)
250 W (at 50 °C ambient temperature)
Mounting:
The antenna can be attached in two ways with
the supplied mounting kit:
1. On the tip of a tubular mast of 40 – 54 mm
diameter (connecting cable runs inside the
mast).
2. Laterally at the tip of a tubular mast of
20 – 54 mm diameter (connecting cable runs
outside the mast).
Material:
Radiator: Brass.
Radome: Fiberglass, colour: Grey.
Base: Weather-proof aluminum.
Mounting kit, screws and nuts: Stainless steel.
Grounding:
All metal parts of the antenna as well as
the inner conductor and the mounting kit
are DC grounded.
30°
3
dB
VPol
10
0
Vertical Pattern
Mechanical specifications
Input
N female
Connector position
Bottom
Weight
0.90 kg
Radome diameter
Wind load
Max. wind velocity
Packing size
On the tip
124
Laterally at the tip
Height
21 mm
20 N (at 150 km/h)
200 km/h
825 x 112 x 97 mm
715 mm
Brackets for side mounting (see page 198 – 200)
Omnidirectional Antennas
Vertical Polarization
870 – 960
V
VPol Omni 870–960 360° 8dBi
Type No.
736 350
Frequency range
870 – 960 MHz
Polarization
Vertical
Gain
8 dBi
Impedance
50 Ω
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
1543 mm
VSWR
< –150 dBc
Max. power
500 W (at 50 °C ambient temperature)
Mounting:
The antenna can be attached laterally at the tip
of a tubular mast of 50 – 94 mm diameter with
two U-bolt brackets supplied with the antenna
(connecting cable runs outside the mast).
Material:
Radiator: Copper and brass. Radome:
Fiberglass, colour: Grey.
Base: Weather-proof aluminum.
Mounting kit, screws and nuts: Stainless steel.
Excellent grounding:
From the solid metal tip right down to the base
of the high gain antennas the grounding crosssection is 22 mm2 copper or more, exceeding
EN 50083-1.
The inner conductor is coupled capacitively.
13°
VPol
3
dB
10
0
Vertical Pattern
Mechanical specifications
Input
230
um
maximtop
mast
7-16 female
Connector position
Bottom
Weight
5.5 kg
Radome diameter
150
736 350
Wind load
Max. wind velocity
Packing size
51 mm
130 N (at 150 km/h)
200 km/h
1846 x 148 x 112 mm
104
Height
Brackets for side mounting (see page 198 – 200)
1543 mm
125
Omnidirectional Antennas
Vertical Polarization
806 – 894
V
VPol Omni 806–894 360° 11dBi
Type No.
738 192
Frequency range
806 – 894 MHz
Polarization
Vertical
Gain
11 dBi
50 Ω
Impedance
VSWR
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
500 W (at 50 °C ambient temperature)
Mounting:
The antenna can be attached laterally at the tip
of a tubular mast of 50 – 94 mm diameter with
two U-bolt brackets supplied with the antenna
(connecting cable runs outside the mast).
Material:
Radiator: Copper and brass.
Radome: Fiberglass, colour: Grey.
Base: Weather-proof aluminum.
Mounting kit, screws and nuts: Stainless steel.
Excellent grounding:
From the solid metal tip right down to the base
of the high gain antennas the grounding crosssection is 22 mm2 copper or more, exceeding
EN 50083-1.
The inner conductor is coupled capacitively.
3237 mm
Max. power
7°
VPol
3
dB
10
0
Vertical Pattern
Mechanical specifications
Input
230
um
maximtop
mast
7-16 female
Connector position
Bottom
Weight
8.5 kg
150
Radome diameter
Wind load
Max. wind velocity
Packing size
51 mm
230 N (at 150 km/h)
180 km/h
3516 x 148 x 112 mm
104
Height
126
3237 mm
Brackets for side mounting (see page 198 – 200)
Omnidirectional Antennas
Vertical Polarization
870 – 960
V
VPol Omni 870–960 360° 11dBi
Type No.
736 347
Frequency range
870 – 960 MHz
Polarization
Vertical
Gain
11 dBi
50 Ω
Impedance
VSWR
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
500 W (at 50 °C ambient temperature)
Mounting:
The antenna can be attached laterally at the tip
of a tubular mast of 50 – 94 mm diameter with
two U-bolt brackets supplied with the antenna
(connecting cable runs outside the mast).
Material:
Radiator: Copper and brass.
Radome: Fiberglass, colour: Grey.
Base: Weather-proof aluminum.
Mounting kit, screws and nuts: Stainless steel.
Excellent grounding:
From the solid metal tip right down to the base
of the high gain antennas the grounding crosssection is 22 mm2 copper or more, exceeding
EN 50083-1.
The inner conductor is coupled capacitively.
3033 mm
Max. power
7°
VPol
3
dB
10
0
Vertical Pattern
Mechanical specifications
Input
um
maximtop
mast
230
Connector position
Weight
150
Radome diameter
Wind load
Max. wind velocity
Packing size
736 347
7-16 female
Bottom
8 kg
51 mm
210 N (at 150 km/h)
200 km/h
3316 x 148 x 112 mm
104
Height
Brackets for side mounting (see page 198 – 200)
3033 mm
127
Omnidirectional Antennas
Vertical Polarization
Fixed Electrical Downtilt
870 – 960
V
5°
VPol Omni 870–960 360° 10.5dBi 5°T
Type No.
736 349
Frequency range
870 – 960 MHz
Polarization
Vertical
Gain
10.5 dBi
Electrical tilt
5°, fixed
Impedance
50 Ω
VSWR
< 1.5
< –150 dBc
Max. power
2954 mm
Intermodulation IM3
(2 x 43 dBm carrier)
500 W (at 50 °C ambient temperature)
Mounting:
The antenna can be attached laterally at the tip
of a tubular mast of 50 – 94 mm diameter with
two U-bolt brackets supplied with the antenna
(connecting cable runs outside the mast).
Material:
Radiator: Copper and brass.
Radome: Fiberglass, colour: Grey.
Base: Weather-proof aluminum.
Mounting kit, screws and nuts: Stainless steel.
Excellent grounding:
From the solid metal tip right down to the base
of the high gain antennas the grounding crosssection is 22 mm2 copper or more, exceeding
EN 50083-1.
The inner conductor is coupled capacitively.
7°
VPol
3
dB
10
0
Vertical Pattern
5° electrical downtilt
Mechanical specifications
Input
um
maximtop
mast
7-16 female
230
Connector position
Weight
Bottom
8 kg
Radome diameter
150
736 349
Wind load
Max. wind velocity
Packing size
51 mm
210 N (at 150 km/h)
200 km/h
3316 x 148 x 112 mm
104
Height
128
2954 mm
Brackets for side mounting (see page 198 – 200)
Dual-band Omni Antenna
Vertical Polarization
Indoor and outdoor use
870 – 960 / 1710–1880
V
VPol Omni 870–960/1710–1880 360° 2dBi
738 449
Type No.
Input
1 x N female
Connector position
Bottom or top
Frequency range
870 – 960 MHz / 1710 – 1880 MHz
VSWR
< 1.7
Gain
2 dBi
Impedance
50 Ω
< –150 dBc
Polarization
Vertical
Max. power
50 Watt: 870 – 960 MHz
50 Watt: 1710 – 1880 MHz
(at 50 °C ambient temperature)
Weight
250 g
Radome diameter
20 mm
Height
216 mm
Material:
Radiator: Brass.
Radome: Fiberglass, colour: White.
Mounting:
One hole mounting (16 mm diameter) to surfaces
of max. 10 mm thickness.
216 mm
Intermodulation IM3
(2 x 43 dBm carrier)
78°
dB
3
VPol
10
0
Vertical Pattern
129
Dual-band Omni Antenna
Vertical Polarization
Indoor and outdoor use
824 – 960 /1805 –2170
V
VPol Omni 824–960/1805–2170 360° 2dBi
800 10147
Type No.
Input
1 x N female
Connector position
Bottom or top
824 – 960 MHz / 1805 – 2170 MHz
VSWR
< 2.0
Gain
2 dBi
Impedance
50 Ω
Polarization
Vertical
Max. power
50 Watt: 824 – 960 MHz
50 Watt: 1805 – 2170 MHz
(at 50 °C ambient temperature)
Weight
250 g
Radome diameter
20 mm
Height
216 mm
Material:
Radiator: Brass.
Radome: Fiberglass, colour: White.
Mounting:
One hole mounting (16 mm diameter) to surfaces
of max. 10 mm thickness.
Grounding:
All metal parts of the antenna as well as
the inner conductor and the mounting kit
are DC grounded.
78°
3
dB
VPol
10
0
Vertical Pattern
130
216 mm
Frequency range
Dual-band Omni Antenna
870 – 960
1710–1880
870 – 960
1710–1880
V
V
Vertical Polarization
VVPol Omni 870–960/1710–1880 360°/360° 2/2dBi
741 862
Polarization
Gain
Isolation, between ports
Upper unit
870 – 960 MHz
1710 – 1880 MHz
Lower unit
870 – 960 MHz
1710 – 1880 MHz
Vertical
Vertical
2 dBi
2 dBi
> 25 dB
> 25 dB
Impedance
50 Ω
50 Ω
VSWR
< 1.8
< 1.8
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
50 W (at 50 °C ambient temperature)
493 mm
Frequency range
Material:
Radiator: Copper and brass.
Radome: Fiberglass, colour: Grey.
Base: Weather-proof aluminum.
Mounting kit and screws: Stainless steel.
Mounting:
The antenna can be attached laterally at the
tip of a tubular mast of 40 – 70 mm diameter
with a mounting clamp supplied with the
antenna. The connecting cables (not supplied)
run outside the mast.
Excellent grounding:
The metal parts of the antenna and the mounting
kit (exclusive the inner conductor of the upper
unit) are DC grounded.
130 mm
Type No.
870– 960
1710–1880
870– 960
1710–1880
N
N
3
dB
10
VPol
78°
0
Vertical Pattern
Mechanical specifications
Input
Connector position
Weight
Wind load
Max. wind velocity
Packing size
2 x N female
Bottom
1.2 kg
30 N (at 150 km/h)
200 km/h
665 x 112 x 97 mm
Height
496 mm
Radome diameter
30 mm
Bottom view
131
Multi-band Omni Antenna
870 – 960
1710 –1880
1920 – 2170
V
V
Vertical Polarization
VVPol Omni 870–960/1710–1880/1920-2170 360°/360° 2/2dBi
800 10111
Polarization
Gain
Isolation, between ports
Upper unit
870 – 960 MHz
1710 – 1880 MHz
Lower unit
1920 – 2170 MHz
Vertical
Vertical
2 dBi
2 dBi
> 25 dB
> 25 dB
Impedance
50 Ω
50 Ω
VSWR
< 1.7
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power per input
50 W (at 50 °C ambient temperature)
493 mm
Frequency range
Material:
Radiator: Copper and brass.
Radome: Fiberglass, colour: Grey.
Base: Weather-proof aluminum.
Mounting kit and screws: Stainless steel.
Mounting:
The antenna can be attached laterally at the
tip of a tubular mast of 40 – 70 mm diameter
with a mounting clamp supplied with the
antenna. The connecting cables (not supplied)
run outside the mast.
Excellent grounding:
The metal parts of the antenna and the mounting
kit (exclusive the inner conductor of the upper
unit) are DC grounded.
130 mm
Type No.
78°
870– 960
1710–1880
1920 – 2170
N
N
3
dB
VPol
10
0
Vertical Pattern
Mechanical specifications
Input
Connector position
Weight
Wind load
Max. wind velocity
Packing size
Bottom view
132
2 x N female
Bottom
0.85 kg
30 N (at 150 km/h)
200 km/h
665 x 112 x 97 mm
Height
493 mm
Radome diameter
30 mm
Omnidirectional Antenna
Vertical Polarization
1710–1880
V
VPol Omni 1710–1880 360° 8dBi
739 785
Type No.
Frequency range
1710 – 1880 MHz
Vertical
Gain
8 dBi
Impedance
50 Ω
VSWR
807 mm
Polarization
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power
200 W (at 50 °C ambient temperature)
Mounting:
The antenna can be attached laterally at the tip
of a tubular mast of 50 – 94 mm diameter with
one U-bolt bracket supplied with the antenna
(connecting cable runs outside the mast).
Material:
Radiator: Copper and brass.
Radome: Fiberglass, colour: Grey.
Base: Weather-proof aluminum.
Mounting kit, screws and nuts: Stainless steel.
Excellent grounding:
From the solid metal tip right down to the base
of the high gain antennas the grounding crosssection is 22 mm2 copper or more, exceeding
EN 50083-1.
The inner conductor is coupled capacitively.
13°
VPol
3
dB
10
0
Vertical Pattern
Mechanical specifications
Input
130
um
maximtop
mast
Connector position
Weight
Radome diameter
104
Wind load
Max. wind velocity
Packing size
Height
Brackets for side mounting (see page 198 – 200)
7-16 female
Bottom
4 kg
51 mm
90 N (at 150 km/h)
200 km/h
986 x 148 x 112 mm
807 mm
133
Omnidirectional Antennas
Vertical Polarization
1710–1880
V
VPol Omni 1710–1880 360° 11dBi
738 187
Type No.
Frequency range
1710 – 1880 MHz
Polarization
Vertical
Gain
11 dBi
50 Ω
Impedance
< 1.3
Intermodulation IM3
(2 x 43 dBm carrier)
1568 mm
VSWR
< –150 dBc
Max. power
200 W (at 50 °C ambient temperature)
Mounting:
The antenna can be attached laterally at the tip
of a tubular mast of 50 – 94 mm diameter with
two U-bolt brackets supplied with the antenna
(connecting cable runs outside the mast).
Material:
Radiator: Copper and brass.
Radome: Fiberglass, colour: Grey.
Base: Weather-proof aluminum.
Mounting kit, screws and nuts: Stainless steel.
Excellent grounding:
From the solid metal tip right down to the base
of the high gain antennas the grounding crosssection is 22 mm2 copper or more, exceeding
EN 50083-1.
The inner conductor is coupled capacitively.
7°
VPol
3
dB
10
0
Vertical Pattern
Mechanical specifications
Input
230
um
maximtop
mast
7-16 female
Connector position
Bottom
Weight
5.5 kg
Radome diameter
150
738 187
Wind load
Max. wind velocity
Packing size
51 mm
130 N (at 150 km/h)
200 km/h
1846 x 148 x 112 mm
104
Height
134
1568 mm
Brackets for side mounting (see page 198 – 200)
Omnidirectional Antenna
Vertical Polarization
Fixed Electrical Downtilt
1710–1880
V
6°
VPol Omni 1710–1880 360° 11dBi 6°T
737 190
Type No.
Frequency range
1710 – 1880 MHz
Polarization
Vertical
Gain
11 dBi
6°, fixed
Impedance
50 Ω
VSWR
< 1.3
Intermodulation IM3
(2 x 43 dBm carrier)
1560 mm
Electrical tilt
< –150 dBc
Max. power
200 W (at 50 °C ambient temperature)
Mounting:
The antenna can be attached laterally at the tip
of a tubular mast of 50 – 94 mm diameter with
two U-bolt brackets supplied with the antenna
(connecting cable runs outside the mast).
Material:
Radiator: Copper and brass.
Radome: Fiberglass, colour: Grey.
Base: Weather-proof aluminum.
Mounting kit, screws and nuts: Stainless steel.
Excellent grounding:
From the solid metal tip right down to the base
of the high gain antennas the grounding crosssection is 22 mm2 copper or more, exceeding
EN 50083-1.
The inner conductor is coupled capacitively.
7°
VPol
3
dB
10
0
Vertical Pattern
6° electrical downtilt
Mechanical specifications
Input
230
um
maximtop
mast
Connector position
Bottom
Weight
5.5 kg
Radome diameter
150
7-16 female
Wind load
Max. wind velocity
Packing size
51 mm
130 N (at 150 km/h)
200 km/h
1846 x 148 x 112 mm
104
Height
Brackets for side mounting (see page 198 – 200)
1560 mm
135
Omnidirectional Antenna
Vertical Polarization
Indoor and outdoor use
1710–2170
V
VPol Omni 1710–2170 360° 2dBi
738 454
Type No.
Input
N female
Connector position
Bottom or top
1710 – 2170 MHz
VSWR
< 1.5
Gain
2 dBi
Impedance
50 Ω
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Polarization
Vertical
Max. power
50 W (at 50 °C ambient temperature)
Weight
150 g
Radome diameter
20 mm
Height
115 mm
Material:
Radiator: Brass.
Radome: Fiberglass, colour: White.
Mounting:
One hole mounting (16 mm diameter) to surfaces
of max. 10 mm thickness.
Grounding:
All metal parts of the antenna and the mounting
kit are DC grounded. The inner conductor is not
DC grounded.
78°
3
dB
VPol
10
0
Vertical Pattern
136
115 mm
Frequency range
Omnidirectional Antenna
Vertical Polarization
1920–2170
V
VPol Omni 1920–2170 360° 11dBi
741 790
Type No.
Frequency range
1920 – 2170 MHz
Polarization
Vertical
Gain
11 dBi
50 Ω
Impedance
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
1387 mm
VSWR
< –150 dBc
Max. power
150 W (at 50 °C ambient temperature)
Mounting:
The antenna can be attached laterally at the tip
of a tubular mast of 50 – 94 mm diameter with
one U-bolt bracket supplied with the antenna
(connecting cable runs outside the mast).
Material:
Radiator: Copper and brass.
Radome: Fiberglass, colour: Grey.
Base: Weather-proof aluminum.
Mounting kit, screws and nuts: Stainless steel.
Excellent grounding:
From the solid metal tip right down to the base
of the high gain antennas the grounding crosssection is 22 mm2 copper or more, exceeding
EN 50083-1.
The inner conductor is coupled capacitively.
7°
VPol
3
dB
10
0
Vertical Pattern
Mechanical specifications
Input
130
um
maximtop
mast
Connector position
Weight
Radome diameter
104
Wind load
Max. wind velocity
Packing size
Height
Brackets for side mounting (see page 198 – 200)
7-16 female
Bottom
5 kg
51 mm
120 N (at 150 km/h)
200 km/h
1570 x 148 x 112 mm
1387 mm
137
138
Summary – Indoor Antennas
Vertical Polarization
Multi-band
Type
Type No.
Frequency
range
Connector
female
Page
VPol BiDir 824–960/1710–2170
65°
5dBi
738 446
824 – 960 MHz and
1710 – 2170 MHz
N
140
VPol Indoor 824–960/1710–2170
90°
7dBi
742 149
824 – 960 MHz and
1710 – 2170 MHz
N
141
VPol Indoor 1710–2170
360°
2dBi
741 573
1710 – 2500 MHz
N
142
VPol Indoor 824–960/1425–2170
360°
2dBi
741 572
824 – 960 MHz and
1425 – 2170 MHz
N
143
VPol Indoor 876–960/1710–2500
360°
2dBi
800 10137
876 – 960 MHz and
1710 – 2500 MHz
N
143
VPol Indoor 824–960/1425–2170
360°
2dBi
800 10177
824 – 960 MHz and
1425 – 2170 MHz
N
144
VPol Indoor 876–960/1710–2500
360°
2dBi
800 10173
876 – 960 MHz and
1710 – 2500 MHz
N
144
738 450
870 – 960 MHz
N
145
Indoor / Outdoor – Single-band
VPol Omni 870–960
360°
2dBi
VPol Omni 870–960/1710–1880
360°
2dBi
738 449
870 – 960 MHz and
1710 – 1880 MHz
N
146
VPol Omni 1710–2170
360°
2dBi
738 454
1710 – 2170 MHz
N
147
Indoor
VPol
Indoor / Outdoor – Dual-band / Multi-band
139
Multi-band Bidirectional Antenna
Vertical Polarization
Half-power Beam Width
824 – 960/1710 –2170
V
65°
VPol BiDir 824–960/1710–2170 65° 5dBi
738 446
Type No.
Input
1 x N female
Frequency range
824 – 960 MHz, 1710 – 2170 MHz
< 1.5
824 – 960 MHz: 5 dBi
1710 – 1880 MHz: 5.5 dBi
1880 – 2170 MHz: 6.5 dBi
Impedance
50 Ω
Polarization
Vertical
Max. power (total)
200 W (at 50 °C ambient temperature)
Weight
0.8 kg
Wind load
Frontal:
Lateral:
Rearside:
Max. wind velocity
25 N (at 150 km/h)
65 N (at 150 km/h)
35 N (at 150 km/h)
200 km/h
Packing size
422 x 212 x 95 mm
Height/width/depth
310 / 55 / 190 mm
Material:
Radiator: Tin plated copper.
Reflector: Weather-proof aluminum.
Radome: High impact plastic, colour: Grey.
All screws and nuts: Stainless steel.
Mounting:
Wall mounting: No additional mounting kit
needed.
For pipe mast mounting use clamps listed on the
datasheet (order separately).
Ice protection:
The radiating system is protected by the radome.
Due to its very sturdy construction, the antenna
remains operational even under icy conditions.
Grounding:
All metal parts of the antenna as well as the
inner conductor are DC grounded.
3
dB
10
0
Typical Horizontal Pattern
140
372 mm
Gain
8.5 mm
400 mm
VSWR
Indoor Multi-b. Direct. Antenna
Vertical Polarization
Half-power Beam Width
Integrated Combiner
824 – 960
1710 –2170
V
V
90°
90°
C
VVPol Indoor 824–960/1710–2170 90° 7dBi
742 149
Type No.
Frequency range
824 – 960 MHz / 1710 – 2170 MHz
Polarization
Vertical
≈ 7 dBi
Gain
Horizontal: ≈ 90°
Half-power beam width
50 Ω
Impedance
VSWR
Max. power
Input
870 – 960 MHz and 1710 – 1900 MHz: < 1.6
824 – 960 MHz and 1710 – 2170 MHz: < 2.0
50 W (at 50 °C ambient temperature)
Cable RG 223/CU of 1m length, white,
with N female connector
Weight
500 g
Packing size
321 x 165 x 50 mm
Height/width/depth
205 / 155 / 42 mm
824 – 960
VPol
1710 – 2170
VPol
C
N
Radiator: Brass.
Radome: ABS, colour: White.
Reflector: Aluminum.
Mounting plates: Stainless steel.
Mounting:
Two holes of 6 mm diameter in the mounting
plate.
Grounding:
All metal parts inclusive the inner conductor are
DC grounded.
Available accessories:
Broadband power splitter (800 – 2500 MHz).
90°
10
3
dB
Material:
0
Horizontal Pattern
VPol
Mounting:
Mount the attachment plate to the wall
using two screws of 4 mm diameter
in the position as indicated.
Align the antenna over the attachment
plate, keeping the cable in the middle
of the plate.
Pull the antenna downwards until
it clicks into place.
141
Indoor Omnidirectional Antenna
Vertical Polarization
Multi-band
1710 –2500
V
The antenna can be operated in the total frequency range
simultaneously.
● The antenna needs no additional groundplane.
●
VPol Indoor 1710–2500 360° 2dBi
100 mm dia.
741 573
Type No.
Frequency range
1710 – 2500 MHz
VSWR
1710
1850
1920
2170
–
–
–
–
1880
1990
2170
2500
MHz:
MHz:
MHz:
MHz:
Input
1 x N female
Gain
2 dBi
Impedance
50 Ω
Polarization
<
<
<
<
1.6
1.6
1.6
2.0
Vertical
Max. power (per band)
50 W (at 50 °C ambient temperature)
Weight
150 g
Diameter
100 mm
Height
50 mm (without connector)
Material:
Base: Aluminum.
Protective housing: High impact polystyrol,
colour: White.
Additional painting is possible.
Mounting:
Holes in the base enable a mounting on the
ceiling. Screws are supplied.
For the N connector a hole in the ceiling with
a diameter of 35 mm is required.
Grounding:
All metal parts including the inner conductor
are DC grounded.
Available accessories:
Broadband power splitters and tappers
(800 – 2500 MHz).
min. dia. 35 mm
N connector, female
VPol
80 mm
2 holes dia. 5 mm
12.9 mm
Clip the protective housing into position after
the antenna has been mounted with the help
of the three supplied screws.
142
Indoor Omnidirectional Antennas
Vertical Polarization
Multi-band
800/2000/2500
V
The antenna can be operated in all frequency ranges
simultaneously.
● The antennas need no additional groundplane.
●
741 572: VPol Indoor 824–960/1425–2170 360° 2dBi
800 10137: VPol Indoor 876–960/1710–2500 360° 2dBi
Type No.
Frequency range
VSWR
741 572
800 10137
824 – 960 MHz
1425 – 2170 MHz
876 – 960 MHz
1710 – 2500 MHz
< 2.0: 824 – 960 MHz
< 2.0: 1425 – 1710 MHz
< 1.6: 1710 – 1990 MHz
< 2.0: 1990 – 2170 MHz
< 1.9: 876 – 890 MHz
< 1.6: 890 – 960 MHz
< 1.6: 1710 – 2170 MHz
< 2.0: 2170 – 2500 MHz
Input
1 x N female
Gain
2 dBi
Impedance
50 Ω
Polarization
∅ 260 mm
741 572
Vertical
Max. power (per band)
50 W (at 50 °C ambient temperature)
Weight
Diameter
Height
400 g
300 g
260 mm
210 mm
78 mm (without connector)
Material:
Base: Aluminum.
Protective housing: High impact polystyrol,
colour: White.
Additional painting is possible.
Mounting:
Three holes in the base enable a mounting on
the ceiling. Two types of screws are supplied.
For the N connector a hole in the ceiling with a
diameter of 35 mm is required.
Grounding:
All metal parts including the inner conductor
are DC grounded.
Available accessories:
Broadband power splitters and tappers
(800 – 2500 MHz).
min. dia. 35 mm
3 holes dia. 5 mm
dia. 160 mm
VPol
N connector, female
13 mm
Clip the protective housing into position after
the antenna has been mounted with the help
of the three supplied screws.
143
Indoor Omnidirectional Antennas
Vertical Polarization
Multi-band
800/2000/2500
New pleasant design.
The antenna can be operated in all frequency ranges
simultaneously.
● The antennas need no additional groundplane.
800 10177: VPol Indoor 824–960/1425–2170 360° 2dBi
800 10173: VPol Indoor 876–960/1710–2500 360° 2dBi
V
●
●
∅ 265 mm
800 10177 800 10173
Type No.
Frequency range
VSWR
824 – 960 MHz
1425 – 2170 MHz
876 – 960 MHz
1710 – 2500 MHz
< 2.0: 824 – 960 MHz
< 2.0: 1425 – 1710 MHz
< 1.6: 1710 – 1990 MHz
< 2.0: 1990 – 2170 MHz
< 1.8: 876 – 890 MHz
< 1.6: 890 – 960 MHz
< 1.6: 1710 – 2170 MHz
< 2.0: 2170 – 2500 MHz
Input
1 x N female
Gain
2 dBi
Impedance
50 Ω
Polarization
800 10177
Vertical
Max. power (per band)
50 W (at 50 °C ambient temperature)
Weight
Diameter
Height
480 g
340 g
265 mm
215 mm
85 mm (without connector)
Material:
Base: Aluminum.
Protective housing: High impact polystyrol,
colour: White.
Additional painting is possible.
Mounting:
Three holes in the base enable a mounting on
the ceiling. Two types of screws are supplied.
For the N connector a hole in the ceiling with a
diameter of 35 mm is required.
Grounding:
All metal parts including the inner conductor
are DC grounded.
Available accessories:
Broadband power splitters and tappers
(800 – 2500 MHz).
min. dia. 35 mm
3 holes dia. 5 mm
dia. 160 mm
VPol
N connector, female
13 mm
144
Clip the protective housing into position after
the antenna has been mounted with the help
of the three supplied screws.
Omnidirectional Antenna
Vertical Polarization
Indoor and outdoor use
870 – 960
V
VPol Omni 870–960 360° 2dBi
738 450
Type No.
Input
N female
Connector position
Bottom or top
Frequency range
870 – 960 MHz
VSWR
< 1.5
Gain
2 dBi
Impedance
50 Ω
< –150 dBc
Polarization
Vertical
Max. power
100 W (at 50 °C ambient temperature)
Weight
200 g
Radome diameter
20 mm
Height
180 mm
Material:
Radiator: Brass.
Radome: Fiberglass, colour: White.
Mounting:
One hole mounting (16 mm diameter) to surfaces
of max. 10 mm thickness.
Grounding:
All metal parts of the antenna as well as
the inner conductor and the mounting kit
are DC grounded.
180 mm
Intermodulation IM3
(2 x 43 dBm carrier)
78°
3
dB
10
0
VPol
Vertical Pattern
145
Dual-band Omni Antenna
Vertical Polarization
Indoor and outdoor use
870 – 960 / 1710–1880
V
VPol Omni 870–960/1710–1880 360° 2dBi
738 449
Type No.
Input
1 x N female
Connector position
Bottom or top
Frequency range
870 – 960 MHz / 1710 – 1880 MHz
VSWR
< 1.7
Gain
2 dBi
Impedance
50 Ω
< –150 dBc
Polarization
Vertical
Max. power
50 W: 870 – 960 MHz
50 W: 1710 – 1880 MHz
(at 50 °C ambient temperature)
Weight
250 g
Radome diameter
20 mm
Height
216 mm
Material:
Radiator: Brass.
Radome: Fiberglass, colour: White.
Mounting:
One hole mounting (16 mm diameter) to surfaces
of max. 10 mm thickness.
78°
3
dB
10
0
VPol
Vertical Pattern
146
216 mm
Intermodulation IM3
(2 x 43 dBm carrier)
Omnidirectional Antenna
Vertical Polarization
Indoor and outdoor use
1710–2170
V
VPol Omni 1710–2170 360° 2dBi
738 454
Type No.
Input
N female
Connector position
Bottom or top
1710 – 2170 MHz
VSWR
< 1.5
Gain
2 dBi
Impedance
50 Ω
Intermodulation IM3
(2 x 43 dBm carrier)
115 mm
Frequency range
< –150 dBc
Polarization
Vertical
Max. power
50 W (at 50 °C ambient temperature)
Weight
150 g
Radome diameter
20 mm
Height
115 mm
Material:
Radiator: Brass.
Radome: Fiberglass, colour: White.
Mounting:
One hole mounting (16 mm diameter) to surfaces
of max. 10 mm thickness.
Grounding:
All metal parts of the antenna and the mounting
kit are DC grounded. The inner conductor is not
DC grounded.
78°
3
dB
10
0
VPol
Vertical Pattern
147
148
Summary – Remote Electrical Tilt (RET)
Type
Type No.
Page
RET-system Components
150
Controlling the RCU
151
Communication between OMC and CCU
154
Browser Application
156
Attachment of the RCU
157
Instructions of Feederline Installation
F-Panel with four connectors arranged on two levels
158
A-Panel with four connectors arranged on two levels
159
Triple-band antennas with Kathrein installation tool
160
Remote Control Unit (RCU)
860 10003
161
Central Control Unit (CCU)
860 10006 / 860 10026
162
Power Supply and Signal Cable
860 10007
163
DC Power and Signal Splitter
860 10002
164
Lightning Protection Device
860 10030
165
Earthing Clamp
860 10031
166
782 10147 / ..48 / ..49
167
782 10253 / ..54 / ..55 / ..56
168
Double Tower Mounted Amplifier
Smart Bias Tee
RET
Datasheets of RET-components
149
System for Remote Electrical Tilt (RET)
RET-system Components
RCU
(Remote Control Unit)
• Remote controlled motor, mounted at the
antenna and used to adjust the downtilt angle
CCU
(Central Control Unit)
• Controls several RCUs
• Provides power for connected devices;
e.g. RCU, TMA and/or Smart Bias Tees
• Handles alarming
• Designed for indoor BTS installation
Control cable
• Feeds power supply and control signals to the
RCUs
DC power and signal splitter
• Allocates power supply and control signals from
a common input onto three outputs for multiple
RCU-control
Lightning protection device
• Protects the RET system against lightning
• Needs to be utilised if RCUs are controlled with
separate cable
Earthing clamp
• Grounds the control cable
TMA
(Tower Mounted Amplifier)
• Installed to enhance coverage and improve
voice quality
• Forwards power supply and control signals to
connected RCUs
Smart Bias Tee
• Employed to feed control signals and power
supply onto the RF cables
Optional
150
System for Remote Electrical Tilt (RET)
Controlling the RCU
Alarm interface OC
RS 232
Ethernet
RCU interface
DC power
supply –48 V
AC power supply
110 – 240 V
(optional)
The major component to control the RCU is the
The number of RCUs and the maximum usable
Central Control Unit (CCU), which is located at
cable length, depend on power losses along the
the BTS. In order to cover all required
cables.
applications, the CCU can be accessed from the
Following, a summary of different examples is
Operational Maintenance Center (OMC) via the
given about how to connect RCUs using sepa-
Ethernet input and/or directly by a personal
rate cables:
RCU
Three options may be offered:
RCU
– using Smart Bias Tee’s in the feeder lines
– via TMA
connected to a single CCU.
Splitter
Max. cable
length 150 m
Utilising splitters up to nine RCUs may be
RCU
Max. cable
length 25 m
– Separate cables
XXPol
Antenna
Connection between CCU and RCU
XXPol
Antenna
XXPol
Antenna
computer via the RS 232 input.
The 5-conductor cable consists of two wires
RET
Use of separate cables
CCU
for the HDLC data, two wires for the +29 V
respectively +13 V power supplies and one for
BTS
grounding.
Example to connect 3 RCUs with separate cables
151
System for Remote Electrical Tilt (RET)
Controlling the RCU
Tees
XXPol
Antenna
XXPol
Antenna
XXPol
Antenna
Via feeder cable employing two Smart Bias
In order to reduce installation efforts and costs,
RCU
RCU
RCU
RCU
RCU
RCU
Kathrein offers a solution, which uses the feeder
line to forward the control signal and the power
Max. cable
length 25 m
supply up to the RCU.
3:1 Splitter
3:1 Splitter
3:1 Splitter
Max. cable
length 100 m
One of Kathrein’s Smart Bias Tees is added into
the feeder line close to the base station.
3:1 Splitter
A second Smart Bias Tee is mounted near the
antennas to recover the control signal and DC
voltage from the feeder.
Due to the use of the existing feeder line for the
CCU
RCU controlling, there is no need to install a
separate cable with its own lightning protection
BTS
system.
RCU
RCU
RCU
RCU
RCU
RCU
RCU
RCU
Splitter
RCU
RCU
XXPol
Antenna
RCU
Splitter
RCU
Splitter
RCU
Max. cable
length 25 m
Splitter
Smart
Bias-Tee
Splitter
Max. cable
length 150 m
Splitter
XXPol
Antenna
XXPol
Antenna
XXXPol
Antenna
RCU
Max. cable
length 25 m
RCU
XXXPol
Antenna
XXXPol
Antenna
Example to connect 6 RCUs with separate cable
3:1 Splitter
Max. cable
length 100 m
Feeder cable
RET
Smart
Bias-Tee
3x
BTS UMTS
CCU
CCU
3x BTS GSM 1800
BTS
Example to connect 9 RCUs with separate cables
152
Example to connect 6 RCUs utilising two Smart Bias Tees
System for Remote Electrical Tilt (RET)
Controlling the RCU
Via feeder cable utilising one Smart Bias Tee
AISG (Antenna Interface Standards Group)
and one TMA
Especially with UMTS, tower mounted amplifiers
(TMA) are implemented to the system to
enhance coverage and improve voice quality.
An elegant way of controlling the RET system is
to combine a Kathrein TMA and a RCU. Both,
the control signal and DC power supply are fed
onto the RF cable via a Smart Bias-Tee. The
TMA includes a Smart Bias-Tee to recover
Kathrein’s overall RET system works according
signals and voltage from the feeder cable
the AISG standard.
forwarding them to the connected RCU’s.
The AISG was founded in 2001 as a sub-group
Each of the three CCU outputs is suitable for the
of the UMTS standardisation group 3GPP
connection of one TMA and max. 3 RCU’s.
(3G Partnership Project).
The purpose of the AISG standard is to embed
RCU
RCU
RCU
define all interfaces and protocols between the
XXPol
Antenna
XXPol
Antenna
XXPol
Antenna
the RET control into the UMTS standard and
RCU
RCU
CCU and the RCU. The link between the OMC
and the BTS is not standardised by the AISG!
RCU
Max. cable
length 25 m
Splitter
Splitter
TMA
TMA
Several antenna and TMA manufacturers
(including Kathrein) as well as operators and
Splitter
TMA
OEM’s are members of the AISG. The groups’
overall goal is to guarantee the basic interoperability of antennas and the control infrastructure.
Feeder cable
Smart
Bias-Tee
Smart
Bias-Tee
Smart
Bias-Tee
CCU
3x
BTS UMTS
RET
3x BTS GSM 1800
Example to connect 6 RCUs utilising Smart Bias Tees and TMAs
153
System for Remote Electrical Tilt (RET)
Communication between OMC and CCU
Overview of general CCU network integration
The electrical tilt can be controlled either locally
pattern has to be adjusted much more often
or remotely.
compared to a GSM network. To meet this
demand, a remote controlled system via OMC
Local control:
is inevitable. The Ethernet interface may be
Configuration of the RET system and simple
selected for remote control in a local area
adaptation to network changes can be made
network (LAN) or wide area network (WAN).
RET
via local control. In this case, an installation
team has to be sent out to the site. A laptop is
The following transport and application protocols
connected to the RS232 interface and PPP link
are served by the CCU: TCP/IP, PPP, UDP,
at the CCU.
DHCP, HTML and ICMP/Ping. In future, the
Alternatively, you may use the Ethernet inter-
CCU will also be able to support a selection from
face.
the application protocols: XML-RPC, FTP,
Telnet, SNMP and NFS.
Remote control:
Due to the required network optimisation with
It is also anticipated that the software of the
UMTS, the downtilt of the vertical radiation
CCU will be extended to allow the operation of a
154
System for Remote Electrical Tilt (RET)
Communication between OMC and CCU
cablemodem or GSM-modem connected to the
Connection via modems
RS232 interface.
The hardware interface RS232 on the CCU can
Different ways to communicate with the CCU
be utilised to connect modems.
from the OMC (Operational Maintenance
If a fixed telephone line is available at the site,
Center) can be chosen depending on the net-
the link between the OMC and the CCU can
work connections implemented:
be accomplished using cable modems on both
Antenna
sides.
Fixed Line
Connection via ethernet
RCU
The base station transceivers on different sites
OMC
Ethernet
are surveyed from the OMC via a supplier
specific Ethernet connection.
Antenna
address and control the CCU from the OMC.
Ethernet
RS232
Modem
Modem
BTS-Control
BTS
Fixed line
RCU
CCU-Control
CCU
RS232
Kathrein is also using the medium Ethernet to
OMC
RS485
CCU-Control
Fixed line
Communication between OMC and CCU via fixed line
Ethernet
RS485
In case of missing Ethernet and fixed telephone
CCU
lines at the site a GSM-modem enables a wireless solution.
BTS
Antenna
Wireless
Communication between OMC and CCU via Ethernet
RCU
OMC
Ethernet
RS485
CCU-Control
RS232
CCU
RS232
Modem
Modem
BTS-Control
BTS
Communication between OMC and CCU via wireless units
RET
BTS-Control
155
System for Remote Electrical Tilt (RET)
Browser Application
The CCU runs a webserver. RCUs and CCUs as
RCUs, to also display the device status, com-
part of a network can be configured and
mand history list and various system errors. It is
controlled through a standard browser, e.g.
also possible to perform CCU software updates.
Netscape, Internet Explorer – no additional soft-
The browser application is a helpful tool for the
ware is required. You can control the RET-
installation team on site, especially during initial
system directly on site or via a long distance.
configuration of a RET-system
The connection to each CCU is generated easi-
Each CCU and with it each of the connected
ly by typing in its individual IP-address.
RCUs can be addressed and controlled
The appearing website contains all required
individually. Therefore, the browser application
control functions for normal service and
also offers a comfortable solution to respond on
installation.
new situations by changing the individual
The CCU program allows in addition to the
downtilt angles fast and easily.
configuration and control of the connected
RET
tion
orma
f
n
i
r
rthe
For fu see the
al !
manu
e
r
a
w
soft
Screenshot of CCU browser application
156
Attachment of the RCU
Attachment of the RCU (Remote Control Unit) for remote-controlled downtilt adjustment:
Check the proper functioning of the phase-shifter
over the entire adjustment
range, by twisting the
adjustment wheel in such a
way that the spindle moves
completely in and out.
Reset the downtilt to the
previous value.
Completely remove the black
adjustement wheel by simply
pulling it downwards.
Push the attachment nut of
the RCU down towards the
housing.
Place the RCU carefully over
the adjustment spindle,
observing the correct alignment of the RCU with regards
to the antenna, i.e. the flat
surfaces of the attachment
fixture on the antenna side
and those inside the RCU
housing must lie flat against
each other.
Push-up the RCU carefully to
the stop at the antenna.
Tighten the RCU attachment
nut using a torque-wrench;
wrench width = 41 mm,
min. torque = 15 Nm
max. torque = 18 Nm.
Connect the RCU control
cable immediately after
attachment of the RCU.
Please note!
In cases where a mechanical downtilt unit is installed,
this must not be set
for a downtilt of more than
14 degrees.
Please note!
Do not twist the RCU in
any way during attaching to
the antenna, as this could
damage the adjustment
spindle.
RET
Remove the protective cap
completely from the antenna.
157
General Instructions for Feederline Installation
for F-Panels
with four Connectors arranged on two Levels
Please note:
In order not to damage the interfaces, please make sure that only the right tools are used. For fixing the nut
of the connector we recommend using a common torque-wrench with a suitable wrench width.
Description of connector arrangement:
4
2
3
1
There are four interfaces for feeding the
antenna located at the bottom.
To make the installation of the feederlines
and the connectors easier, the interfaces
are arranged on two levels.
Attachment of the feederline connector and the RCU:
Start with the rearside located interface
no. 1.
After feederline installation the remote
control units (RCU) can be attached.
For full description of RCU installation see
datasheet Type no. 860 10003.
Place the connector carefully and fix the
nut using a torque-wrench (according to
the manufacturers guidelines).
RET
The further sequence for the installation is:
feederlines no. 2, 3, 4.
Please note:
Sealing of the correctly installed connector’s cap nuts for additional weather protection is not required, nor is
it recommended by the connector manufacturers.
158
General Instructions for Feederline Installation
for A-Panels
with four Connectors arranged on two Levels
Please note:
In order not to damage the interfaces, please make sure that only the right tools are used. For fixing the nut
of the connector we recommend using a common torque-wrench with a suitable wrench width.
Description of connector arrangement:
4
2
3
1
There are four interfaces for feeding the
antenna located at the bottom.
To make the installation of the feederlines
and the connectors easier, the interfaces
are arranged on two levels.
Attachment of the feederline connector and RCU:
Start with the rearside located interface
no. 1.
After feederline installation the remote
control units (RCU) can be attached.
For full description of RCU installation see
datasheet Type no. 860 10003.
Place the connector carefully and fix the
nut using a torque-wrench (according to
the manufacturers guidelines).
Please note:
Sealing of the correctly installed connector’s cap nuts for additional weather protection is not required, nor is
it recommended by the connector manufacturers.
159
RET
The further sequence for the installation is:
feederlines no. 2, 3, 4.
General Instructions for Feederline Installation
for Triple-band Antennas
with Kathrein Installation Tool, Type No. 850 10005
Note: To avoid any damage to the interfaces, please ensure that only suitable tools are used. To tighten
the nuts of the feederline connectors, we strongly recommend using a special Kathrein installation tool
(as shown below) in combination with a standard torque-wrench.
Description of connector arrangement:
Kathrein installation tool: Type No. 850 10005
1/2″ square actuation according to
DIN 3120 Form C
2
1
RET
interfaces (1–3)
3
27 or 32 mm
Feederline
connectors (4–9)
8
6
4
5
7
9
There are six RF-Connections and three RET-interfaces located at
the bottom of the antenna.
This tool is suitable for 7-16 connectors with a wrench size of
27 mm or 32 mm.
Tighten nut within a torque range of 25 – 33 Nm depending on
connector manufacturers’ specifications.
The tool has to be ordered separately!
Two tools per type no. (27 and 32 mm) were delivered in a
common package.
Attachment of the feederline connector and RCU:
A
B
The sequence for installation is: feederline no. 4, 5, 6, 7, 8, 9. Put the connector carefully in place
and hand-screw the nut on.
Use a torque-wrench to finish installation (see installation tool).
Repeat operations as shown in figures A and B for each feederline!
Note:
In order to protect
the RET interface the
protective caps have
to be attached during
feederline
installation!
RET
Before RCU installation, it is absolutely
essential to set the
downtilt to 0° (either
manually or by
remote control).
After feederline installation, the remote control units (RCU) can be attached,
The sequence for the installation of the RCU’s is: RCU no. 1, 2, 3.
For full description of RCU installation please refer to data sheet type no. 860 10003.
Not following these
instructions may
damage the downtilt
spindle!
Note: Sealing of the correctly installed connector’s cap nuts for additional weather protection is not
required, nor is it recommended by the connector manufacturers.
160
Remote Control Unit (RCU)
Remote Control Unit (RCU) for Kathrein base station antennas
with adjustable electrical downtilt and appropriate mechanical
interface.
Type No.
Power supply
Hardware interface
Logical interface
Adjustment time (full range)
860 10003
10 … 30 V
RS485
HEX coded commands
based on HDLC protocol, conform to AISG
typically 30 sec., depending on antenna type
Adjustment cycles
> 50000
Temperature range
–40 °C … +60 °C
Material of housing
Aluminum
Weight
approx. 1.1 kg
Packing size
297 x 217 x 135 mm
Dimensions
85 x 130 x 150 mm (without connectors)
Scope of supply:
RCU with suitable attachment interface for the
antenna.
Features:
The RCU can be easily attached without
dismantling of the antenna.
The RCU is suitable for operation under outdoor
conditions.
RCU in combination
with antenna 742 212
Two RCUs in combination
with antenna 742 234
As a result of more stringent legal regulations and judgements regarding product liability, we are
obliged to point out certain risks that may arise when products are used under extraordinary
operating conditions.
The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4,
which includes the static mechanical load imposed on an antenna by wind at maximum velocity.
Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused
by oscillating support structures), may result in the breakage of an antenna/RCU or even cause it to fall
to the ground.These facts must be considered during the site planning process.
The installation team must be properly qualified and also be familiar with the relevant national
safety regulations.
The details given in our data sheets have to be followed carefully when installing the antennas
and accessories.
The limits for the coupling torque of RF-connectors, recommended by the connector manufacturers must be obeyed.
Any previous datasheet issues have now become invalid.
161
RET
Please note:
Central Control Unit (CCU)
For Remote Electrical Tilt (RET/RCU) and
Tower Mounted Amplifier (TMA) Control, Indoor Use
Central Control Unit
Type No.
860 10006
Connectors to RCU
3 x 8 pin connector according DIN 41 326, IEC 130, female,
conform to AISG
Power supply from BTS
860 10026
DC: –48 V / max. 1.5 A
AC: 110 V … 240 V / max 0.7 A
DC: –48 V / max. 1.5 A
Power supply to RCU
3 x +29 V / max. 2 A / max. 50 W
Power supply to RCU
(via TMA)
3 x 13 V / max. 1.5 A / max. 50 W
Interface to RCU and TMA
RS 485 / power supply
Protocol
HDLC hex-coded command set, conform to AISG
Interface to BTS
and protocol
Ethernet (10 base T) or RS 232
SNMP, HTTP, XML-RPC
Alarm interface to BTS
8 x open collector output
Modem support
GSM, Siemens MC35 Terminal or TC35 Terminal
Max. number of RCU’s
and/or TMA’s
6 … 9 pcs., depending on cable configuration and max. power
Max. length of control cable
100 m / 6 RCU’s (depending on configuration)
Temperature range
–25 °C ... +55 °C ambient temperature
Packing size
597 x 367 x 148 mm
Height/width/depth
19" 1 HU* (43.6 / 483 / 250 mm)
(12
(24
(12
(24
V), BTS
V), BTS
V), Antenna
V), Antenna
Antenna
10253
10255
10254
10255
Antenna
782
782
782
782
Antenna
Bias Tee
Bias Tee
Bias Tee
Bias Tee
Antenna
Smart
Smart
Smart
Smart
Antenna
* HU = Height Unit
RCU
RCU
RCU
RCU
RCU
RS 485
Smart
Bias Tee
TMA
Splitter 1:3
Smart
Bias Tee
Accessories (order separately)
RET
162
Splitter for RCU
Remote Control Unit (RCU)
RCU-Cable
RCU-Cable
RCU-Cable
RCU-Cable
RCU-Cable
RCU-Cable
RCU-Cable
RCU-Cable
RCU-Cable
RCU-Cable
RCU-Cable
RCU-Cable
Ethernet Cable Crossover
To Splitter or to RET/TMA via Smart Bias Tee
3 x RS 485
and 3 x +13 V / 3 x +29 V
1
2
3
5
10
20
25
40
50
60
80
100
3
m
m
m
m
m
m
m
m
m
m
m
m
m
Central Control Unit
Ethernet 8 x Open
Collector
PC/Modem
AC
Depending
on Type No.
Alarm
interface
10002
10003
10007
10008
10029
10009
10010
10032
10011
10012
10033
10013
10014
10015
10034
Length
Interface
Network
860
860
860
860
860
860
860
860
860
860
860
860
860
860
860
Description
RS 232
Type No.
Smart
Bias Tee
DC:
–48 V
AC:
110 V – 240 V
Power Supply and Signal Cable
For Remote Control Unit (RCU)
Indoor and Outdoor Use
Cable for RCU assembled with suitable connectors for
Remote Control Unit / Splitter / Central Control Unit
860 10007 …
Type No.
Connectors
2 x 8 pin connector
according
DIN 41 326, IEC 130, female/male
Construction
Screen
1 x twisted pair 100 Ω/1 MHz
2 x power supply, 1 x ground
AWM style 20317 I/II A/B
Rated current
4 A (power supply)
(at 50 °C air temperature)
Temperature range
–40 °C to +80 °C, (fixed position)
Protection class
IP 67 (connected)
Cable diameter
8 mm
Flammability
VL 1581 VW-1
CSA
FT 1
Minimum bending radius:
one time
60 mm
several times 120 mm
RCU-Cable
Type No.
Description
Length
860
860
860
860
860
860
860
860
860
860
860
860
RCU-Cable
RCU-Cable
RCU-Cable
RCU-Cable
RCU-Cable
RCU-Cable
RCU-Cable
RCU-Cable
RCU-Cable
RCU-Cable
RCU-Cable
RCU-Cable
1
2
3
5
10
20
25
40
50
60
80
100
m
m
m
m
m
m
m
m
m
m
m
m
RET
10007
10008
10029
10009
10010
10032
10011
10012
10033
10013
10014
10015
163
DC-Power and Signal Splitter
For Remote Control Unit (RCU)
Indoor and Outdoor Use
3-way-Splitter for RCU
860 10002
Type No.
Connectors
4 x 8 pin connector
according DIN 41 326, IEC 130-9
1 x male, 3 x female
Locking of connector
Screwing
Rated current (power supply)
3 A (at 50 °C)
Max. voltage
60 V
Protection class
IP 65
Weight
250 g
Packing size
114 x 117 x 117 mm
Height/width/depth
91 / 103 / 72 mm
Material:
Connector plate: Aluminum.
Cap: Plastic.
Mounting:
To masts, 50 – 145 mm diameter by clamp
(supplied).
Wall mounting by screws (not supplied).
Note:
Connectors must be situated at the bottom.
No inverted mounting possible.
2 pins
(power supply, max. 3 A)
6 pins
(max. 0.1 A)
Output 1
Output 2
Output 3
RET
Input
Clamp, Art. No. 1311847
164
Lightning Protection Device (LPD)
For Remote Electrical Tilt (RET)
Indoor and Outdoor Use
The device is designed for lightning protection of control cables
carrying partial lightning currents up to 25 kA (shield) and
2,5 kA (inner conductor), according IEC 61643-1, IEC 61312-3.
Each pin is protected individually.
Lightning Protection Device for RET
860 10030
Connectors
2 x 8 pin connector
according DIN 41 326, IEC 130-9,
input: male, output: female
SPD-Type
8 x bipolar gas tube
Max. impuls current
Max. dynamic overvoltage
at spark gap (1 kV/µs)
Static overvoltage (100 V/s)
Grounding
25 kA (housing, shield) (10/350 µs)
inner conductors: 2,5 kA/pin (10/350 µs)
< 700 V
< 100 V
Via mounting plate / clamps at metallic surfaces
or via separate cable,
min. cross-section 5 mm2 Cu (screw M6)
Max. operation current
4 A at 50 °C
Max. operation voltage
60 V
Weight
Packing size
Height/width/depth
250 g
114 x 117 x 117 mm
91 / 103 / 72 mm
Material:
Connector plate: Aluminum.
Cap: Plastic.
Mounting:
To masts, 50 – 145 mm diameter by clamp
(supplied).
Wall mounting by screws M4 (not supplied).
Note:
No decoupling elements are integrated. The
coordination with additional LPD’s (device input)
should be checked according to IEC 61312.
Grounding of the device via the mounting plate
at metallic surfaces or via additional grounding
cable (not included in the delivery extend).
Connectors must be situated at the bottom.
No inverted mounting possible.
Important: A control cable with a minimum
length of 2 meters is required between Lightning
Protection Device and Central Control Unit at
the BTS to achieve the required decoupling.
RET
Type No.
Clamp, Art. No. 1311847
165
Earthing Clamp
For Power Supply and Control Cable
For Remote Control Unit (RCU)
The clamp is designed for lightning protection of control cables
according to EN 50164-1
Earthing clamp for RCU power supply and signal cable
Type No.
Max. lightning current
Contact resistance
Protection class
Grounding
Packing size
Weight
860 10031
≤ 100 kA (pulse 10/350 µsec)
< 1 mΩ
IP 68
Via stranded grounding wire,
16 mm2, length 1 m,
with integrated cable eyes, hole diameter 8 mm
Plastic bag: 210 x 210 mm
240 g
Body: Stainless steel with vulcanized EthylenePropylene-Caoutchouc
Screw: Stainless steel
Skin: Copper alloy
Grounding wire: Copper
Please note:
The earthing clamp is suitable only for the
Kathrein Power Supply and Signal Cables,
Type No. 860 10007 to 860 10015, 860 10029,
860 10032 and 860 10033 or shielded cables
with
– shield diameter 6.1 mm
– jacket diameter 7.8 mm ±0.3 mm
RET
Material:
166
DTMA UMTS AISG
Fullband Double Dual Duplex Tower Mounted Amplifier
(Masthead Amplifier)
• Double unit for easy use with XPol antennas
• Kathrein Cold Redundancy (patent pending) amplifier design for
improved system reliability
• By-pass mode to ensure cell operation in case of TMA failure
• Built-in lightning protection
• Compact size
• Suitable for antenna RET control according to AISG standard
RET = Remote Electrical Tilt
AISG = Antenna Interface Standards Group
Technical Data
Type No.
782 10147
782 10148
782 10149
DTMA UMTS 12 AISG DTMA UMTS 24 AISG DTMA UMTS 32 AISG
(12 dB gain)
(24 dB gain)
(32 dB gain)
Intermodulation products in Rx band
Return loss
Ant 1
2110 – 2170 MHz
60 MHz
Typically 0.3 dB
< ±0.2 dB
< 100 W (+50 dBm) CW
< 1.6 kW (+62 dBm) Peak
< –120 dBm (2 Tx carriers at +43 dBm)
Typically 20 dB
Rx Characteristics
Frequency range
Bandwidth
Loss in by-pass mode
Gain ripple
Return loss
Gain
–40 … +65 °C
+22 … +28 °C
Noise figure
Output 1-dB compression point
3rd order intercept point (OIP3)
Environmental Characteristics
Operating temperature range
IP rating
MTBF
EMC
DC and Alarm Characteristics
DC supply voltage
Power consumption
Alarm management
Modem Characteristics
Mechanical Characteristics
Material
Connectors
RF
RET DC
Mounting
Weight
Packing size
Dimensions (w x h x d)
1920 – 1980 MHz
60 MHz
< 2.6 dB (DC OFF)
< ±0.3 dB
Typically 20 dB
20 dB (DC ON)
> 12 dB (DC OFF)
12 ±1.0 dB
12 ±0.5 dB
Typically 1.5 dB
> 15 dBm
> 25 dBm
24 ±1.0 dB
24 ±0.5 dB
Typically 1.5 dB
> 20 dBm
> 30 dBm
Ant 0
BTS 1
BTS 0
Accessories (order separately)
32 ±1.0 dB
32 ±0.5 dB
Typically 1.8 dB
> 27 dBm
> 37 dBm
–40 … +65 °C
IP67
> 500 000 hours (Double TMA)
ETS 300 343-3
Type No.
Clamp set
suitable for mast
diameter of
734 360
34 – 60 mm
734 361
60 – 80 mm
734 362
80 – 100 mm
734 363
100 – 120 mm
734 364
120 – 140 mm
734 365
45 – 125 mm
+12 V nominal (minus grounded)
+24 V nominal
(minus grounded)
Typically 1.5 W per TMA Typically 3 W per TMA Typically 8 W per TMA
According to AISG standard
According to AISG standard
Aluminium housing
RET
Tx Characteristics
Frequency range
Bandwidth
Insertion loss
Ripple
Input power
7-16 female
8-pin female, IEC 60130-9
(Pin 1: +12 V DC nominal, pin 3: RS485A, pin 5: RS485B,
pin 7: DC return, pin 6: 24 V DC; other pins: Not connected)
Wall mounting: With 4 screws (max. 8 mm diameter)
Mast mounting: With additional clamp set
5 kg
502 mm x 262 mm x 214 mm
172 mm x 262 mm x 84 mm
(without connectors, without mounting brackets)
167
Smart Bias Tee
800 – 2170 MHz
The Smart Bias Tee combines the performance of a standard
Bias Tee (e. g. type 793 304) with the function of an additional
modem (AISG standard) in order to provide either DC voltage
as well as remote control signals via an RF feeder cable to a
TMA or RCU.
The Smart Bias Tee provides low RF signal insertion loss from
port 1 to port 2 and vice versa.The measures taken to protect
against static discharge and lightning ensure a high level of
reliability and operational safety.
• 782 10253: 12 V version for use near the BTS, in order to
feed-in DC voltage and RCU control signals into a feeder
cable
• 782 10254: 12 V version for use near the antenna, in order
to control an RCU (only required if no TMA is in use)
• 782 10255: 24 V version for use near the BTS, in order to
feed-in DC voltage and RCU control signals into a feeder
cable
• 782 10256: 24 V version for use near the antenna, in order
to control an RCU (only required if no TMA is in use)
782 10253
Port 1
Port 2
Port DC/RCU
Block diagram
782 10254
782 10256
Abbreviations:
RCU = Remote Control Unit for remote electrical control of
antenna tilt
BTS = Base Transceiver Station
TMA = Tower Mounted Amplifier
AISG = Antenna Interface Standards Group
Port 1 = Port for BTS/Antenna
Port 2 = Port for feeder cable
Port DC/RCU = Port for DC voltage and remote control unit signals
Antenna system
(1 sector)
without TMA
Block diagram
782 10253
782 10255
Antenna system
(1 sector)
with Kathrein TMA
Application Examples
Technical Data
Type No.
RET
Connectors
Port 1
Port 2
Port DC/RCU
Frequency range
Insertion loss
Port 1 ↔ Port 2
Isolation for DC and RCU signals
Port 1 ↔ Port 2
Port 1 ↔ Port DC/RCU
Port 2 ↔ Port DC/RCU
VSWR (all ports)
Input power
Port 1 or port 2
Port DC/RCU
Intermodulation products
Impedance
Temperature range
Modem carrier frequency
Application
Weight
Dimensions (w x h x d)
168
782 10253
782 10254
782 10255
782 10256
12 V / BTS
12 V / Antenna
24 V / BTS
24 V / Antenna
7-16 male
7-16 female
8-pin male connector
8-pin female connector
8-pin male connector
8-pin female connector
(IEC 60130-9)
(IEC 60130-9)
(IEC 60130-9)
(IEC 60130-9)
Pin 1: 12 VDC in
Pin 1: 12 VDC out
Pin 6: 24 VDC in
Pin 6: 24 VDC out
(Pin 3: RS485-A, pin 5: RS485-B. pin 7: ground, other pins: not connected)
800 – 2170 MHz
< 0.1 dB (800 – 2170 MHz)
> 70 dB
> 70 dB
0 dB
< 1.1 (800 – 2170 MHz)
< 250 W (800 – 2170 MHz)
< 250 W (800 – 2170 MHz)
< 2.5 A / +8 … +14 VDC
< 2.5 A / +14 … +30 VDC
< –160 dBc (3rd order; with 2 x 20 W)
50 Ω
–40 ... +60 °C
2.176 MHz
Indoor or outdoor (IP66)
0.65 kg
128 mm x 76 mm x 46 mm (including connectors)
Summary – Electrical Accessories
Splitters
Type
Type No.
2-way-Splitter 800/900
2-way-Splitter 800/900
2-way-Splitter
2-way-Splitter
3-way-Splitter
3-way-Splitter
4-way-Splitter
4-way-Splitter
K 63 20 62 1
K 63 20 62 7
800–2200
800–2200
800–2200
800–2200
800–2200
800–2200
2-way-Splitter 800–2500
3-way-Splitter 800–2500
4-way-Splitter 800–2500
Frequency
range
737
737
737
737
737
737
303
304
305
306
307
308
Remark
Max.
power
Connector Page
female
790 – 960 MHz Indoor/Outdoor 500 W
790 – 960 MHz Indoor/Outdoor 1000 W
N
7-16
170
170
800
800
800
800
800
800
N
7-16
N
7-16
N
7-16
171
171
171
171
171
171
N
N
N
172
172
172
–
–
–
–
–
–
2200
2200
2200
2200
2200
2200
MHz
MHz
MHz
MHz
MHz
MHz
Indoor/Outdoor
Indoor/Outdoor
Indoor/Outdoor
Indoor/Outdoor
Indoor/Outdoor
Indoor/Outdoor
200
700
200
700
200
700
W
W
W
W
W
W
860 10017
860 10018
860 10019
800 – 2500 MHz
800 – 2500 MHz
800 – 2500 MHz
Indoor
Indoor
Indoor
100 W
100 W
100 W
Type
Type No.
Frequency
range
Remark
Max.
power
2-way-Tapper 800–2500 7.0/1.0 dB
2-way-Tapper 800–2500 10.4/0.4 dB
2-way-Tapper 800–2500 15.1/0.1 dB
860 10020
860 10021
860 10022
800 – 2500 MHz
800 – 2500 MHz
800 – 2500 MHz
Indoor
Indoor
Indoor
100 W
100 W
100 W
N
N
N
173
173
173
500 W
500 W
500 W
7-16
7-16
7-16
174
174
174
Tappers
2-way-Tapper 800–2200 7.0/1.0 dB K 63 23 60 67
2-way-Tapper 800–2200 10.4/0.4 dB K 63 23 61 07
2-way-Tapper 800–2200 15.1/0.1 dB K 63 23 61 57
800 – 2200 MHz Indoor/Outdoor
800 – 2200 MHz Indoor/Outdoor
800 – 2200 MHz Indoor/Outdoor
Connector Page
female
Continuously adjustable ratio
2-way-Tapper 824–960/1710–2170 K 63 23 60 01 824 – 960 MHz
5.0–15.0dB
1710 – 2170 MHz
Indoor
100 W
N
175
2-way-Tapper 870–960/1710–2500
5.0–15.0dB
Indoor
100 W
N
175
Filter products summary
– Combiners, Filters, Bias Tees
– Duplexers
– DTMA
– 3-dB Couplers
870 – 960 MHz
1710 – 2500 MHz
tion
forma
n
i
d
e
gue
etail
For d the catalo lters,
e
z Fi
se
0 MH lifiers
0
5
2
–
“790 ners, Amp ations”
i
c
Comb Communi
e
l
i
b
o
for M
176
177
178
179
Electrical
Accessories
860 10023
169
Multi-band Low-loss Power Splitters
790 – 960
For indoor and outdoor use.
2-way-Splitter 790–960
K 63 20 62 1 K 63 20 62 7
Type No.
Frequency range
790 – 960 MHz
For connecting ... antennas
2
Insertion loss
< 0.05 dB
50 Ω
Impedance
VSWR
< 1.1
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power
500 W
1000 W
(at 50 °C ambient temperature)
Connector (female)
N
Weight
7-16
approx. 1.3 kg
Packing size
240 x 93 x 107 mm
Max. size
210 / 80 / 80 mm
Material:
Housing: Aluminum.
Inner conductor: Brass.
Mounting:
Bracket for wall mounting included in the scope
of supply: For pipe mast mounting use clamps
listed below (order separately).
DC capability:
DC transmission between all terminations
(suitable for remote power supply systems).
Input
K 63 20 62 7
Clamps (order separately)
Type No.
736
736
736
736
736
801
802
803
804
805
Description
1
1
1
1
1
clamp
clamp
clamp
clamp
clamp
Remarks
Mast:
Mast:
Mast:
Mast:
Mast:
34
60
80
100
120
–
–
–
–
–
60
80
100
120
140
mm
mm
mm
mm
mm
diameter
diameter
diameter
diameter
diameter
736 805
170
Multi-band Low-loss Power Splitters
800 –2200
For indoor and outdoor use.
2-way-Splitter 800–2200
3-way-Splitter 800–2200
4-way-Splitter 800–2200
737 303 737 304 737 305 737 306 737 307 737 308
Type No.
Frequency range
800 – 2200 MHz
For connecting ... antennas
2
3
Insertion loss
4
< 0.05 dB
50 Ω
Impedance
VSWR
< 1.15
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power
(at 50 °C ambient temperature)
Connector (female)
200 W
700 W
200 W
700 W
200 W
700 W
N
7-16
N
7-16
N
7-16
Weight
approx. 1.5 kg
Packing size
310 x 93 x 107 mm
Max. size
294 / 82 / 82 mm
Material:
Housing: Aluminum.
Inner conductor: Brass.
Mounting:
Bracket for wall mounting included in the
scope of supply.
For pipe mast mounting use clamps listed
below (order separately).
DC capability:
DC transmission between all terminations
(suitable for remote power supply systems).
Input
737 308
Clamps (order separately)
736
736
736
736
736
801
802
803
804
805
Description
1
1
1
1
1
clamp
clamp
clamp
clamp
clamp
Remarks
Mast:
Mast:
Mast:
Mast:
Mast:
34
60
80
100
120
–
–
–
–
–
60
80
100
120
140
mm
mm
mm
mm
mm
diameter
diameter
diameter
diameter
diameter
Splitters
Type No.
736 805
171
Multi-band Low-loss Power Splitters
800 –2500
For indoor use.
2-way-Splitter 800–2500
3-way-Splitter 800–2500
4-way-Splitter 800–2500
Type No.
860 10017 860 10018 860 10019
Frequency range
For connecting ... antennas
800 – 2500 MHz
2
3
Insertion loss
< 0.05 dB
50 Ω
Impedance
VSWR
< 1.25
< 1.25
Intermodulation IM3
(2 x 43 dBm carrier)
Max. power
4
< 1.3
< –150 dBc
100 W (at 50 °C ambient temperature)
Connector
N female
Weight
approx. 0.6 kg
Profile cross-section
25 x 25 mm
Packing size
242 x 110 x 95 mm
Max. size
204 / 63 / 41 mm
Material:
Housing: Aluminum.
Inner conductor: Brass.
DC capability:
DC transmission between all terminations
(suitbale for remote power supply systems).
Input
Splitters
860 10019
172
Multi-band Low-loss Power Tappers
800 –2500
For indoor use.
P1
2-way-Tapper 800–2500 7.0 /1.0dB
2-way-Tapper 800–2500 10.4/0.4dB
2-way-Tapper 800–2500 15.1/0.1dB
860 10020 860 10021 860 10022
Frequency range
Tap Loss
Input ↔ P1
Input ↔ P2
800 – 2500 MHz
– 1.0 dB
– 7.0 dB
– 0.4 dB
– 10.4 dB
For connecting ... antennas
P2
– 0.1 dB
– 15.1 dB
2
Insertion loss
< 0.05 dB
Impedance
50 Ω
VSWR
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power
100 W (at 50 °C ambient temperature)
Connector
N female
Weight
approx. 0.5 kg
Profile cross-section
25 x 25 mm
Packing size
267 x 95 x 111 mm
Max. size
244 / 64 / 25 mm
Material:
Housing: Aluminum.
Inner conductor: Brass.
DC capability:
DC transmission only between input and port P1.
P2 is coupled capacitively.
Input
860 10020
Tappers
Type No.
173
Multi-band Low-loss Power Tappers
800 –2200
For indoor and outdoor use.
2-way-Tapper 800–2200 7.0 /1.0dB
2-way-Tapper 800–2200 10.4/0.4dB
2-way-Tapper 800–2200 15.1/0.1dB
P1
K 63 23 60 67 K 63 23 61 07 K 63 23 61 57
Type No.
Frequency range
800 – 2200 MHz
Tap Loss
Input ↔ P1
Input ↔ P2
– 1.0 dB
– 7.0 dB
– 0.4 dB
– 10.4 dB
For connecting ... antennas
– 0.1 dB
– 15.1 dB
2
Insertion loss
P2
< 0.05 dB
Impedance
50 Ω
VSWR
< 1.5
Intermodulation IM3
(2 x 43 dBm carrier)
< –150 dBc
Max. power
500 W (at 50 °C ambient temperature)
Connector
7-16 female
Weight
approx. 1.3 kg
Packing size
310 x 93 x 112 mm
Max. size
244 / 90 / 55 mm
Material:
Housing: Aluminum.
Inner conductor: Brass.
DC capability:
DC transmission only between input and port P1.
P2 is coupled capacitively.
Mounting:
Bracked for wall mounting included in the scope
of supply.
For pipe mast mounting use clamps listed below
(order separately).
Input
K 63 23 60 67
Clamps (order separately)
Type No.
736
736
736
736
736
801
802
803
804
805
Description
1
1
1
1
1
clamp
clamp
clamp
clamp
clamp
Remarks
Mast:
Mast:
Mast:
Mast:
Mast:
34
60
80
100
120
–
–
–
–
–
60
80
100
120
140
mm
mm
mm
mm
mm
diameter
diameter
diameter
diameter
diameter
Tappers
736 805
174
Multi-band
Low-loss Power Tapper
Continuously Adjustable
824 – 960
1710 –2500
5.0 – 15.0
5.0 – 15.0
For indoor use.
P1
K 63 23 60 01: 2-way-Tapper 824–960/1710–2170 5.0–15.0dB
860 10023: 2-way-Tapper 870–960/1710–2500 5.0–15.0dB
K 63 23 60 01 860 10023
Type No.
Frequency range
824 – 960 MHz and
1710 – 2170 MHz
Power ratio between outputs
(P2 – P1)
870 – 960 MHz and
1710 – 2500 MHz
–5.0 dB to –15.0 dB
continuously adjustable
For connecting ... antennas
P2
2
Insertion loss
< 0.1 dB
Impedance
50 Ω
VSWR
< 1.7
Intermodulation IM3
(2 x 43 dBm carrier)
Blocking unit
< –150 dBc
Max. power
100 W (at 50 °C ambient temperature)
Connector
N female
Weight
0.5 kg
Profile cross-section
25 x 25 mm
Packing size
249 x 111 x 40 mm
277 x 111 x 40 mm
Max. size
235 / 100 / 25 mm
263 / 100 / 25 mm
Material:
Housing: Aluminum.
Inner conductor: Brass.
Adjustment mechanism: ASA.
DC capability:
DC transmission only between input and port P1.
P2 is coupled capacitively.
Input
860 10023
Splitting table
Splitting ratio
P1 / P2
–5
–6
–7
–8
–9
– 10
– 11
– 12
– 13
– 14
– 15
3.2
4
5
6.3
8
10
12.6
15.8
20
25.1
31.6
Splitting attenuation
PInput – P1 [dB]
PInput – P2 [dB]
– 1.2
– 1.0
– 0.8
– 0.6
– 0.5
– 0.4
– 0.3
– 0.3
– 0.2
– 0.2
– 0.1
– 6.2
– 7.0
– 7.8
– 8.6
– 9.5
– 10.4
– 11.3
– 12.3
– 13.2
– 14.2
– 15.1
Tappers
P2 / P1 [dB]
175
Combiners, Filters, Bias Tees
50 – 2500 MHz
Dual-band Combiner
793 532
793 533
Single Unit
Double Unit
806 – 960 / 1710 – 2170 MHz
806 – 960 / 1710 – 2170 MHz
782 10250 Single Unit, built-in DC stop
782 10251 Double Unit, built-in DC stop
793 423
793 424
Single Unit
Single Unit
793 532
Single Unit
793 533
Double Unit
782 10250
Single Unit
782 10251
Double Unit
806 – 960 / 1710 – 2170 MHz
806 – 960 / 1710 – 2170 MHz
1710 – 1880 / 1920 – 2170 MHz
1710 – 1880 / 1920 – 2170 MHz
782 10243 Single Unit, built-in DC stop 1710 – 1880 / 1920 – 2170 MHz
782 10244 Double Unit, built-in DC stop 1710 – 1880 / 1920 – 2170 MHz
782 10264 Single Unit
50 – 2200 / 2400 – 2500 MHz
793 423, 782 10243
Single Unit
793 424, 782 10244
Double Unit
793 425, 782 10245
Single Unit
793 426, 782 10246
Double Unit
793 528
Single Unit
793 529
Double Unit
Triple-band Combiner
793 425
793 426
Single Unit
Double Unit
782 10245
Single Unit
880 – 960 / 1710 – 1880 / 1920 – 2170 MHz
built-in DC stop
Double Unit
880 – 960 / 1710 – 1880 / 1920 – 2170 MHz
built-in DC stop
782 10246
793 528
793 529
Single Unit
Double Unit
880 – 960 / 1710 – 1880 / 1920 – 2170 MHz
880 – 960 / 1710 – 1880 / 1920 – 2170 MHz
806 – 960 / 1710 – 1880 / 1920 – 2170 MHz
806 – 960 / 1710 – 1880 / 1920 – 2170 MHz
Smart Bias Tee
782
782
782
782
10253
10254
10255
10256
12
12
24
24
V BTS
V Antenna
V BTS
V Antenna
800
800
800
800
–
–
–
–
2170
2170
2170
2170
MHz
MHz
MHz
MHz
Bias Tee
793 304
800 – 2170 MHz
DC Stop
793 301
800 – 2170 MHz
Filter products
Band-pass Filter
793 540
1710 – 1880 MHz
Low-pass Filter
793 539
176
876 – 960 MHz
For more information please contact: [email protected]
Duplexers
824 – 2170 MHz
Duplexer GSM-R / GSM
793 004
793 005
7-16
N
876 – 880 / 921 – 925 MHz
876 – 880 / 921 – 925 MHz
782
782
782
782
7-16
1 x N, 3 x 7-16
7-16, 19" drawer
7-16, outdoor
890
890
890
890
10164
10165
10161
10162
–
–
–
–
915
915
915
915
/
/
/
/
935
935
935
935
–
–
–
–
960
960
960
960
MHz
MHz
MHz
MHz
793 004
793 005
782 10164 (indoor)
782 10162 (outdoor)
782 10161 (19˝ drawer)
782 10167
7-16
880 – 915 / 925 – 960 MHz
Duplexer AMPS A-Band, B-Band A/B-Band
782 10168
782 10169
7-16
7-16, outdoor
824 – 835 / 869 – 880 MHz
824 – 835 / 869 – 880 MHz
782 10171
782 10172
7-16
7-16, outdoor
835 – 851 / 880 – 896 MHz
835 – 851 / 880 – 896 MHz
782 10215
782 10216
7-16
N
824 – 851 / 869 – 896 MHz
824 – 851 / 869 – 896 MHz
782 10257
782 10265
7-16, 400 W
7-16, 800 W
782 10168, 782 10171
(indoor)
782 10169, 782 10172
(outdoor)
824 – 846.5 / 869 – 891.5 MHz
824 – 846.5 / 869 – 891.5 MHz
782 10215, 782 10257
782 10216
Duplexer GSM 1800 / GSM 1900
792 542
792 544
7-16
7-16
1710 – 1785 / 1805 – 1880 MHz
1850 – 1910 / 1930 – 1990 MHz
Duplexer UMTS
7-16
1920 – 1980 / 2110 – 2170 MHz
Filter products
782 10192
For more information please contact: [email protected]
177
DTMAs
1920 – 2170 MHz
UMTS Double Tower Mounted Amplifier
782 10071
782 10072
12 dB gain
24 dB gain
UL: 1920 – 1980 / DL: 2110 – 2170 MHz
UL: 1920 – 1980 / DL: 2110 – 2170 MHz
UMTS Double Tower Mounted Amplifier
AISG Standard
12 dB gain
24 dB gain
32 dB gain
UL: 1920 – 1980 / DL: 2110 – 2170 MHz
UL: 1920 – 1980 / DL: 2110 – 2170 MHz
UL: 1920 – 1980 / DL: 2110 – 2170 MHz
Filter products
782 10147
782 10148
782 10149
178
For more information please contact: [email protected]
3-dB Couplers
800 – 2500 MHz
3-dB Coupler
793 506
793 006
793 554
7-16, outdoor
7-16, outdoor
7-16, outdoor
806 – 960 MHz
1700 – 2200 MHz
800 – 2200 MHz
3-dB Coupler with Cable Absorber
Antenna
Tx2
Tx1
792 699
792 702
793 555
806 – 960 MHz
1700 – 2200 MHz
800 – 2200 MHz
Measuring Directional Coupler
824 – 2500 MHz
Filter products
792 972
For more information please contact: [email protected]
179
180
Summary – Mechanical Accessories
Clamps, Downtilt Kits ...
Page
Mounting Configurations
182
A-Panels / C-Panels / Eurocell Panels
Dimensions
183
Clamps
185
Three Sector Clamps and Masts
187
2 x A-Panel Mounting Kit
188
Downtilt kits
189
F-Panels
Dimensions
192
Detailed Connector Position
193
Clamps
194
Three Sector Clamp
195
2 x F-Panel Mounting Kit
196
Downtilt kits
197
Slant Compensation
197
Omnidirectional Antennas
Clamp for larger Mast Diameters
198
Side-mounting Brackets
199
Tools
Azimuth Adjustment Tool
201
Kathrein Installation Tool (Triple-band Antenna)
160
181
Mechanical
Accessories
For additional information on the
mounting of antennas, please check
also our broschure:
Mounting Configurations
Small Pipe Diameter
Large Pipe Diameter
Off-set
Flat Surface
Not applicable for Eurocell Panels with connector position
rearside.
Standard Downtilt
182
Off-set Downtilt
A-Panels
Antenna Dimensions
72
64
A
B
C
256 mm
310 mm
350 mm
9
A-Panels
with 65° and 90° Half-power Beam Width
656 mm 1296 mm 1936 mm 2580 mm
710 mm 1350 mm 1990 mm 2634 mm
750 mm 1390 mm 2030 mm 2674 mm
A Corresponds with the antenna height mentioned in the technical data.
A
B
C
B
C
Bottom view
+45°
-45°
116
58
262
72
9
64
Dual-band A-Panels
with 65° Half-power Beam Width
A
B
C
770 mm
824 mm
864 mm
1316 mm
1367 mm
1407 mm
1916 mm
1967 mm
2007 mm
2516 mm
2567 mm
2607 mm
A Corresponds with the antenna height mentioned in the technical data.
A
Adjustment mechanism
with integrated scale
262
Bottom view
183
A-Panels ...
52
139
58
A-Panels / C-Panels / Eurocell Panels
Antenna Dimensions
72
A
B
C
64
9
Triple-band A-Panel
with 65° Half-power Beam Width
1498 mm 2058 mm 2628 mm
1541 mm 2101 mm 2671 mm
1581 mm 2141 mm 2711 mm
A Corresponds with the antenna height mentioned in the technical data.
A
B
C
B
C
149
Adjustment mechanism
with integrated scale
262
Bottom view
72
9
64
C-Panels
A
B
C
1294 mm 1934 mm 2254 mm
1340 mm 1980 mm 2300 mm
1382 mm 2022 mm 2342 mm
A Corresponds with the antenna height mentioned in the technical data.
Eurocell Panels
A
B
C
264 mm
––
––
654 mm
974 mm 1294 mm 1934 mm 2254 mm 2574 mm
710 mm 1030 mm 1350 mm 1990 mm 2310 mm 2630 mm
750 mm 1070 mm 1390 mm 2030 mm 2350 mm 2670 mm
A
A Corresponds with the antenna height mentioned in the technical data.
A-Panels ...
103
Top view
258
184
A-Panels
30° Half-power Beam Width
Mounting Hardware
A-Panels
with 30° Half-power Beam Width
A
B
∅ 11
656 mm 1296 mm 2580 mm
584 mm 1224 mm 2504 mm
A
B
A Corresponds with the antenna height mentioned in the technical data.
177
116
Side view
180.5
348
560
Bottom view
Clamps
Type No.
Description
733 736
K 61 14 03
K 61 14 04
K 61 14 05
2
2
2
2
clamps
clamps
clamps
clamps
Remarks
Mast:
Mast:
Mast:
Mast:
50 – 125 mm diameter
116 – 210 mm diameter
210 – 380 mm diameter
380 – 521 mm diameter
Weight Units per
approx. antenna
5.9
4.6
6.5
9.4
kg
kg
kg
kg
1
1
1
1
Pair of clamps K 61 14 03
Downtilt kits
656 mm
1296 mm
2580 mm
Downtilt angle
Type No.
Weight
0 – 33°
0 – 16°
0 – 8°
733 695
3.4 kg
Downtilt kit 733 695
185
A-Panels ...
Antenna height
A-Panels 65° and 90° / C-Panels / Eurocell Panels
Mounting Hardware
Clamps
C-Panels / Eurocell Panels C-Panels / Eurocell Panels
C-Panels / Eurocell Panels
Antenna height: 2574 mm
Antenna height: 654 mm
Antenna height: 264 mm
to
2254 mm
and all A-Panels 65° and 90°
10
3
10
8
25
10
3
3
8
8
25
25
26
4
65
9 4
1274
1994
2234
54
25
74
Mast diameter
Type No.
Distance A
mm
28 – 64 mm
*731 651*
22 – 30
330 g
see sketch
Large Pipe
new
new
50 – 115 mm
110 – 220 mm
210 – 380 mm
738 546
850 10002
850 10003
18 – 26
47 – 56
48 – 69
1.0 kg
2.7 kg
4.8 kg
see sketch
see sketch
see sketch
Off-set
60 – 115 mm
115 – 210 mm
210 – 380 mm
380 – 521 mm
2.0
2.6
4.0
5.3
see
see
see
see
Description
Small Pipe
A
733
733
733
733
677
678
679
680
117 – 124
146 – 160
148 – 168
150 – 175
Weight Units per
approx. antenna
kg
kg
kg
kg
* Not allowed for panels 742 241, 742 264, 742 265, 742 266
731 651
738 546
733 678
50 mm
A-Panels ...
26 mm
186
40 mm
sketch
sketch
sketch
sketch
A-Panels / C-Panels / Eurocell Panels
3 Sector Panel Arrangement – Mounting Hardware
3 Sector Clamp Kit / Pipe Mast with Flange Base
Slim and unobstrusive design
Nearly cylindrical optical appearance with small outer diameter
● Suitable for all A-Panels 65° and 90° (Single-band, Dual-band)
with weight less than 30 kg including downtilt kit
● Mounting of F-Panels possible but not optimized
●
●
3 Sector Clamp Kit
Type No.
Angle between antennas
Suitable for mast diameter
Type No. of pipe mast
(please order separately)
Number of pieces
742 033
742 034
120°
114.3 mm
742 035
120°
139.7 mm
742 036
2 x 3 sector clamp
2 x 3 sector clamp
2 x mounting support
2 x mounting support
clamp
clamp
Material – 3 sector clamp
Hot-dip galvanized steel Hot-dip galvanized steel
– Mounting support
Aluminum
Aluminum
clamp
– Screws
Stainless steel
Stainless steel
Outer diameter (Dout) of the
3 A-Panel Arrangement
460 mm
482 mm
Weight – Clamp kit
3.0 kg
3.2 kg
– 3 sector clamp
1.4 kg
1.5 kg
64 ± 0.5
Dout
9
E
B
60
°
3 sector clamp
F
C
A
Bottom view without downtilt kit
Mounting support clamp
D
207
228
E
49
49
F
45
45
D
Type No.
Pipe diameter
D
according DIN 2448
Wall thickness pipe
Pipe length
Flange diameter
Flange thickness
S
Hole circle diameter
Number of holes
Hole diameter
Enclosed bolts thread x length
Hot-dip galvanized steel
Weight
Material pipe mast
Material flange base
742 035
742 036
114.3 mm
139.7 mm
6.3 mm
4 mm
3000 mm
3000 mm
210 mm
265 mm
14 ± 1 mm
19 ± 1 mm
170 mm
225 mm
6
6
18 ± 1 mm
18 ± 1 mm
M16 x 100 mm
M16 x 100 mm
Quality min. 8.8
Quality min. 8.8
60 kg
55 kg
S355 J2H (St 52-3N) DIN EN 10210-1
S235 JR G2 (RSt 37-2) DIN EN 10025
Maximum permissible load: According DIN 4131 and DIN 4132
Fatigue class K2
18±1
170
210
225
265
742 035
742 036
187
A-Panels ...
Pipe Mast with Flange Base
129 ± 2
C
217
236
S
Type No.
A
B
742 033
114.3
88
742 034
139.7 100
all dimensions in mm
Torque 8 Nm
3000
D
A-Panels / C-Panels / Eurocell Panels
Mounting Hardware
2 x A-/C-Panel Mounting Kit
Use this mounting kit only for antennas less than
25 kg each.
850 10006
Type No.
No. of pieces
2 x brackets
Suitable for A-/C-Panels
65°, 90° with a max. height
2.6 m
Material: – Clamp
– Screws
Hot-dip galvanized steel
Stainless steel
Weight
Approx. 3.3 kg
Mounting
Screws are supplied
Recommended torque for M8 bolted connections: 12 Nm
64±0.2
0
R1
390±1
64±0.2
73
34
64±0.2
0.5
∅9±
280±0.5
Mounting Accessories (order separately)
Clamps (only the listed clamps are allowed!)
Weight Units per
approx. antenna
Type No.
Description
Remarks
850 10002
1 clamp
Mast: 110 – 220 mm diameter
2.7 kg
2
850 10003
1 clamp
Mast: 210 – 380 mm diameter 4.8 kg
2
A-Panels ...
Please chose the fitting downtilt kit that you need, from the antenna datasheet.
188
A-Panels / C-Panels / Eurocell Panels
Mounting Hardware
Downtilt kit
Antenna height: 654
974
1294
1934
2254
/ 656 mm
mm
/ 1296 mm
/ 1936 mm
/ 2256 mm
Use the downtilt kit together with
the clamps (see page 185 and 186)
Screws supplied
3
0
12
69
15
2
0
Scale
d
llowe
not a ore
e
r
a
lt kits weight m 70,
ownti
d
e
42 2
ith a
h
T
els w 742 266, 7 1
n
a
P
for
42 24
, like:
25 kg 742 272, 7 e page 191
n
a
h
t
se
71,
742 2 ossibility
p
t
l
i
wnt
for do
Antenna height
Downtilt angle
Type No.
654 / 656 mm
0° – 30°
737 972
974 mm
0° – 21°
737 973
1294 / 1296 mm
0° – 16°
737 974
1934 / 1936 mm
0° – 11°
737 975
2254 / 2256 mm
0° – 9°
–
Downtilt kit
without scale*
Type No.
Weight
737 978
approx. 2.8 kg
* Instructions to adjust the required downtilt angle are given in the datasheet or on the rearside of the antenna.
Mounting a downtilt kit enlarges the spacing between mast and antenna by 84 mm.
189
A-Panels ...
Downtilt kit
with scale
Downtilt angle
A-Panels / C-Panels / Eurocell Panels
Mounting Hardware
Downtilt kits
Suitable for:
A-Panels
with an antenna height of 2580 mm
C-Panels / Eurocell Panels
with an antenna height of 2574 mm
Screws supplied
Screws supplied
3
0
12
69
15
2
0
3
0
12
69
Scale
15
2
0
Scale
Type No. 737 971
Downtilt angle: 0° – 8°
ed
t allow re
o
n
s
i
t mo
lt kit
weigh
ownti
70,
The d els with a 266, 742 2
n
2
for Pa g, like: 74 , 742 241
k
2
7
5
e 191
2
2
than
, 742 ity see pag
1
7
2
742
sibil
lt pos
i
t
n
w
for do
Type No. 737 976
Downtilt angle: 0° – 8°
A-Panels ...
The downtilt kits should only be mounted with clamps
738 546, 850 10002, 850 10003
Mounting a downtilt kit enlarges the spacing between mast and antenna by 84 mm.
190
A-Panels / C-Panels / Eurocell Panels
Mounting Hardware
Downtilt Kit
Special downtilt kit for Panel antennas
with a weight greater than 25 kg.
Downtilt kit
M10
supplied
850 10007
Type No.
Preferred range of use
– Panel antennas with a weight of ≥ 25 kg
– Panel antennas with attached mounting plates
– Downtilt kit without scale for universal use
Weight
5.9 kg
Material
Hot-dip galvanized steel
All screws and nuts
M8
supplied
Stainless steel
Recommended mast clamps:
Type No.
Description
Mast diameter
Weight
approx.
Units per
antenna
738 546
1 clamp
50 – 115 mm
1.0 kg
2
850 10002
1 clamp
110 – 220 mm
2.7 kg
2
850 10003
1 clamp
210 – 380 mm
4.8 kg
2
Recommended torque for all bolted connections:
Screw size
Torque
M8
12 Nm
M10
26 Nm
Maximum acceptable load:
Frontal wind load
< 2500 N
Lateral wind load
< 830 N
Antenna weight
≤ 50 kg
64±0.5
0° – 15°
2058 mm
0° – 11°
2516 mm
0° – 8°
2628 mm
0° – 8°
∅9
64±0.5
232
M10
191
A-Panels ...
1498 mm
300
Downtilt angle
72
Antenna height
∅9
72
Downtilt angle
90
F-Panel Accessories
Dimensions of F-Panels with
33° – 105° Half-power Beam Width
Dimensions [mm]
(‘A’ corresponds to the antenna height given on the data sheet)
33° Half-power Beam Width
60° – 105 °Half-power Beam Width
A
B
C
A
B
C
209
263
303
182
236
266
342
396
436
342
396
426
662
716
756
502
556
586
982
1036
1076
662
716
746
1302
1356
1396
702
756
786
1942
1996
2036
982
1036
1066
1302
1356
1386
1622
1676
1706
1942
1996
2026
2582
2636
2666
Front view
Front view
A B C
9
A B C
64
72
ø 8.5
F-Panels
35
64
192
F-Panel Accessories
Dimensions of F-Panels
Detailed Connector Position
Vertical Polarization
60° – 65° Half-power Beam Width
155
90° Half-power Beam Width
155
76
33° Half-power Beam Width
262
52
+45°/–45° Polarization
65° Half-power Beam Width
155
58
90° Half-power Beam Width
155
54
65° and 90° Half-power Beam Width
adjustable electrical downtilt
+45°
155
199
45° Half-power Beam Width
Multi-band
adjustable electrical downtilt
45
30° Half-power Beam Width
Multi-band
adjustable electrical downtilt
299
45
65° Half-power Beam Width
2-Multi-band
adjustable electrical downtilt
299
48
65° Half-power Beam Width
2-Multi-band
adjustable electrical downtilt
323
193
F-Panels
–45°
F-Panel Accessories
Clamps for F-Panels
Clamps suitable for all F-Panels
Type No.
Mast
diameter
Weight
approx.
Units
per antenna
For more information
see data sheets
738 546
850 10002
850 10003
50 – 115 mm
110 – 220 mm
210 – 380 mm
1 kg
2.7 kg
4.8 kg
2
2
2
Type No. 738 546
40 mm
Clamps suitable for all F-Panels with a width of 155 mm until an antenna height of 1302 mm
Type No.
734
734
734
734
734
734
Mast
diameter
360 34 – 60
361 60 – 80
362 80 – 100
363 100 – 120
364 120 – 140
365 45 – 125
mm
mm
mm
mm
mm
mm
Antenna
height
182
182
182
182
182
182
…
…
…
…
…
…
1942
1942
1942
1942
1942
1942
Weight
Units
per
approx. antenna
mm
mm
mm
mm
mm
mm
60 g
70 g
80 g
90 g
110 g
80 g
1
1
1
1
1
1
738 546
50 – 115 mm 182 ... 2582 mm 1 kg
850 10002 110 – 220 mm 182 ... 2582 mm 2.7 kg
850 10003 210 – 380 mm 182 ... 2582 mm 4.8 kg
2
2
2
F-Panels
Type No. 734 362
194
For more information
see data sheets
Clamps are not allowed for
2-Multi-band F-Panels like
742 233, 742 234, 742 235
F-Panels – 3 Sector Panel Arrangement
Mounting Hardware
3 Sector Clamp Kit
Slim and unobstrusive design
Nearly cylindrical optical appearance with small outer diameter
● Suitable for all F-Panels with an antenna housing width
of 155 mm
●
●
3 Sector Clamp Kit
Type No.
742 263
Angle between antennas
Suitable for mast diameter
Number of pieces
120°
88.9 mm
2 x 3 sector clamp
2 x mounting support
clamp
Hot-dip galvanized steel
Aluminum
Material – 3 sector clamp
– Mounting support
clamp
– Screws
Outer diameter (Dout) of the
3 F-Panel Arrangement
Weight – Clamp kit
– 3 sector clamp
Stainless steel
315 mm
3.0 kg
1.4 kg
Remark
This clamp kit is not suitable for use
with additional mechanical downtilt kits
8.2
.9
88
168 ± 2
180 ± 2
65
60
°
64 ± 0.5
Torque 8 Nm
Dout
5°
–4
5°
+45°
Bottom view
195
F-Panels
50
–4
–45°
42
5°
Mounting support clamp
+4
+4
5°
3 sector clamp
F-Panel Accessories
Mounting Hardware
2 x F-Panel Mounting Kit
For arranging two F-Panels 65°, 90° side by side
(on air combining).
● The mounting kit consists of two mounting plates.
●
2 x F-Panel Mounting Kit
Type No.
742 113
No of units
Suitable for F-Panels
65°, 90° with max. height of
Material
Weight
Mounting
2
2m
Hot-dip galvanized steel
approx. 1.6 kg
Screws are supplied
270
101
∅9
64±0.5
∅9
12 18
19
41
20 10
75
10
116
15 15
45°
64±0.5
Configuration without mechanical downtilt
Configuration with mechanical downtilt
03
6
9 12
15
2
0
m
10 m
Use the 2 x F-Panel Mounting Kit
together with the following mounting accessories
Type No. Description
F-Panels
738
733
733
733
733
737
196
546
677
678
679
680
978
1
1
1
1
1
1
clamp
offset clamp
offset clamp
offset clamp
offset clamp
downtilt kit
Remarks
Mast: 50 – 115 mm diameter
Mast: 60 – 115 mm diameter
Mast: 115 – 210 mm diameter
Mast: 210 – 380 mm diameter
Mast: 380 – 521 mm diameter
Downtilt angle:
depending on antenna height
Weight Units per
approx. antenna
1.0
2.0
2.6
4.0
5.3
2.8
kg
kg
kg
kg
kg
kg
2
2
2
2
2
1
For a three sector panel arrangement,
use the mounting kit type no. 742 113
together with the three sector clamp
(see page 195).
F-Panel Accessories
Downtilt Kits and Slant Compensation Kit
for F-Panels
Downtilt Kits with Type No. 737 ... are suitable for all F-Panels
Use the downtilt kit together with
the clamps (see page 194).
Screws supplied
3
0
Downtilt kit
with scale
Downtilt kit
without scale*
12
69
Downtilt angle
Type No.
Type No.
Weight
342 mm
662 mm
982 mm
1302 mm
1622 mm
1942 mm
2582 mm
0° – 54°
0 °– 30°
0° – 21°
0° – 16°
0° – 13°
0° – 11°
0° – 8°
–
737 972
737 973
737 974
–
737 975
737 971
737 978
approx. 2.8 kg
15
Antenna height
2
0
Scale
* Instructions to adjust the required downtilt angle are given in the datasheet or on the rearside of the antenna.
Mounting a downtilt kit enlarges the spacing between mast and antenna by 84 mm.
Downtilt Kits with Type No. 732 ... are suitable for F-Panels until 1302 mm
Use the downtilt kit together with
the clamps (see page 194).
Screws supplied
86
10 4 2
0
Scale
Antenna height
342
502
662
982
1302
mm
mm
mm
mm
mm
Downtilt angle
0°
0°
0°
0°
0°
–
–
–
–
–
40°
25°
20°
14°
10°
Downtilt kit
with scale
Downtilt kit
without scale*
Type No.
Type No.
Weight
–
732 322
732 321
732 318
732 317
732 327
approx. 1.0 kg
* Instructions to adjust the required downtilt angle are given in the datasheet or on the rearside of the antenna.
Mounting a downtilt kit enlarges the spacing between mast and antenna by 42 mm.
Slant Compensation Kit Type No. 732 319
for F-Panels with 60° – 160° Half-power Beam Width
57 mm
77
Weight: appr. 200 g
197
F-Panels
mm
Use the slant compensation kit
type no. 732 319 together with the
clamps (see page 194).
Side-mounting Clamp
Omnidirectional Antennas
Large Pipe
Type No. 738 908
For mast diameters of 94 – 125 mm
Antenna
Mast
b
a
Omni
b
198
Side-mounting Bracket
Omnidirectional Antennas
∅D
Type No. 737 398
Side-mounting bracket
(for mast diameters of 40 – 105 mm)
Type No.
737 398
Bracket
At the top and
at the bottom
Fits for antenna
type no:
900 MHz
736 347
736 348
736 349
736 350
736 351
738 664
A
1800 MHz
739 785
738 187
739 404
737 190
Side-mounting is possible for four fixed distances between the tubular mast and the antenna:
900 MHz
A = 100 mm = 0.3 λ
1800 MHz
(holes 1 and 3)
A = 160 mm = 0.5 λ
A = 240 mm = 0.75 λ
A = 80 mm = 0.5 λ
A
A
A
A
(hole 2)
Bracket
Antenna
Antenna base
Mast
Bracket
Hole 3
D
Pipe
D
Hole 1
D
Horizontal
Radiation Pattern
Spacing
A
Curve
Hole 3
Hole 2
D
Pipe
D
D
Horizontal
Radiation Pattern
100 mm
Spacing
A
Curve
Pipe
D
Curve
Horizontal
Radiation Pattern
Spacing
A
100 mm
40 mm
dB
3
3
0
0
direction from mast
to antenna
80 mm
160 mm
240 mm
direction from mast
to antenna
3
100 mm
240 mm
0
direction from mast
to antenna
199
Omni
100 mm
dB
160 mm
dB
40 mm
Side-mounting Brackets
Omnidirectional Antennas
900
For mast diameters of 40 – 105 mm
Type No.
Bracket
Fits for antenna
type no.
K 61 33 5
K 61 33 6
at the bottom
only
at both the top
and the bottom
øD
K 75 11 6 ..
K 75 15 6 ..
738 779
741 558
Side mounting is possible for three fixed distances between
the tubular mast and the antenna:
100 mm = 0.3 λ
160 mm = 0.5 λ
240 mm = 0.75 λ
Pipe
D
Horizontal
Radiation Pattern
Spacing
A
Curve
Additional gain
to the nominal value
of the antenna gain
A
100 mm
2 dB
160 mm
3 dB
dB
40 mm
3
240 mm
2 dB
0
direction from mast
to antenna
100 mm
2.5 dB
160 mm
3.5 dB
dB
100 mm
3
240 mm
0
Omni
direction from mast
to antenna
200
2.5 dB
K 61 33 6
A-Panel / C-Panel / F-Panel / Eurocell Panel
Accessories
Azimuth Adjustment Tool
Type No. 738 440
Precise azimuth adjustment for mast mounted antennas can easily be achieved by using the azimuth
adjustment tool.
This tool is suitable to all types of Eurocell Panels
• Panels
• A-Panels
• C-Panels
• F-Panels
• X-Pol F-Panels
Elevation
compensation
Target object
Target object
Scale
Move the stopper to central position*
Panel
Clamping device
A-Panel
262
F-Panel 33°
equivalent for
F-Panel
A-Panel
199
F-Panel
F-Panel
155
equivalent for
F-Panel
F-Panel
X-Pol-F-Panel
X-Pol-F-Panel
Instruction:
– Use a map to work out the angle between the designed antenna azimuth and target
(church, building, mountain peak).
– Set this angle on the scale of the adjustment tool.
– Place the adjustment tool onto the antenna and tighten the clamping device.
– Use the telescope to aim at the target object, if necessary, use elevation compensation.
– Then rotate the antenna until the target object appears in the telescope.
201
Tools
* Observe the position of the stopper when fitting the azimuth adjustment tool.
Sales queries, orders, catalogues
or CD-ROM:
Fax: +49 80 31 1 84-8 20
E-Mail: [email protected]
Technical Information:
Fax: +49 80 31 1 84-9 73
E-Mail: [email protected]
Internet: www.kathrein.de
KATHREIN-Werke KG . Telephone +49 80 31 1 84-0 . Fax +49 80 31 1 84-9 91
Anton-Kathrein-Straße 1 – 3 . PO Box 10 04 44 . D-83004 Rosenheim . Germany
Subject to alteration.
9987.147/0204/10/ZW/HA
Please contact for:
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement