Xyron Personal Cutting System คู่มือผู้ใช้

USER MANUAL
|
FI
HBXYRON
Personal Cutting System™
+ pe
E
1 =
- a я
E
a
BEFORE YOU BEGIN
Read these instructions carefully.
If you are missing parts or the product does not
function properly, DO NOT return this product
to the store that you purchased it from.
Immediately Contact Xyron toll-free by dialing
1-877-392-9474.
FOR YOUR SAFETY
Read and observe all cautions and warnings
shown throughout these instructions.
No assembly required
Table of Contents
System Contents
Preparing to use your Personal Cutting System
Installing the Cutting Blade
Loading Paper
Inserting Design Books
Replacing the Cutting Mat
Selecting Shapes or Designs to Cut
Resizing Shapes
Deleting Selected Shapes
General Maintenance
Technical Specs
Trouble Shooting Guide
™
System Contents:
(A) Cutting Machine
(B) Cutting Blade
(C) Cutting Mat
(D) Two Design Books
(E) Power Cable
(F) Shape Removal Tool
Preparing to use your
Xyron Personal Cutting System™
1. Carefully unpack all components — retain all
packaging for future storage or transportation
2. Compare contents to the parts list (fig 1.1). If
any parts are missing, DO NOT return to the
location that you purchased the Personal Cutting
System™. Call Xyron, toll-free, 1-877-394-9474 for
immediate assistance.
3. Place your Xyron on a flat, stable surface close to an
electrical outlet.
WARNING: Do not use this product around
water or other electrical hazards.
Installing the Cutting Blade
1. Make sure the Personal Cutting System™ is off,
and unplugged from electrical outlet.
2. Open the top lid on the top of the Personal Cutting
System™.
3. Carefully remove the blade from the package and
insert into Tool Holder as shown in fig 2.1.
4. Tighten the side-screw by turning clockwise.
Tighten with fingers until snug.
5. If discarding a used or dull blade, place the used
blade into the package of the new replacement
blade, and discard entire package.
fig 2.1 [CAUTION!|
Do not
overtighten as you
could damage the
tool holder.
Loading Paper
1. Pull out the paper/cutting tray by depressing the
button on the front of the tray, and pulling away
from the machine (fig 3.1). The paper/cutting tray
will eject entirely from the machine.
2. Notice of how the
sample paper is
positioned in the
upper left corner
on the paper tray.
This is the proper
position of paper
that you intend to
cut. Remove the
sample paper and
discard.
3. Trim paper that
you intend to cut
to 4"x 4".
4. Position paper on
the tray and align
to the upper left
hand corner. (fig
3.2)
(ViTIPS
1. Open the top lid if you need to manually clear material
of the cutting surface, or to clean the machine.
2.The top lid is designed to snap off the machine if too
much force is applied to during handling. The top lid
simply snaps into place at the back hinge to the
machine. No tools are required.
Paper/Cutting Tray
(ф) пР5
1. To remove the tray, press the button on the tray lip
and pull out of the machine.
2. Inserting the tray. The tray will lock the tray into
place for cutting.
Inserting Xyron Design Books
2. Remove Xyron Design Book from the protective
packaging.
3. Keep the book closed and insert the spine of the
Design Book into the center of the dock
(fig 4.2). Be sure that the entire spine sits firmly
into the dock. If the book does not easily fit into
place, the book may be upside down. If upside
down, remove, rotate and reinsert.
4. When a Design Book is properly loaded, it will
appear as shown in fig 4.3.
5. After proper insertion, open the book to select
shapes.
=;
EN
SS
WARNING: Do not spill liquids onto the
dock. Damage
and risk of shock
could occur.
Exposing the
dock to excessive
moisture, such
as outdoor use,
could cause
safety and
mechanical
hazards.
[CAUTION!|
Do not intentionally touch the
electronic connections located on
the spine of the book. Dirt and oils
can shorten the life of the Design
Book.
[CAUTION!|
Do not transport your Personal
Cutting System” with the dock
extended.
IWARNING|
HAZARDOUS MOVING PARTS
KEEP FINGERS AND OTHER BODY
PARTS AWAY
‘CAUTION!
Do not use the Personal
Cutting System™ with the
dock overhanging a table.
This will cause the dock to
break-away.
1. Ensure good connection between dock and design
books by applying firm pressure to the spine when
inserting into the Personal Cutting System™.
. When the machine is on, and a book is inserted
correctly, the name of the book will appear on the
LCD screen.
. The dock WILL NOT close when a design book is
inserted. To remove a book, simply grab the middle
of the spine and pull up
. Store books in a dry, dust-free location.
. Do not transport your Personal Cutting System™ with
the dock extended and do not attempt to carry your
Personal Cutting System™ by the dock.
Replacing the Cutting Mat
The cutting mat is a self healing, tacky material
that keeps paper in place during the cutting
process. Over time, paper, dust, and dirt
will cause the cutting mat to have a reduced
tacky feel. When paper no longer is held inplace
throughout an entire cut (the blade pushes the
paper around), a new mat is required.
Avoid touching tacky, surface by using the
shape removal tool.
1. Remove the paper/cutting tray by depressing the
button on the tray, and remove completely from the
Personal Cutting System™.
2. To remove the mat grasp a corner of the used
cutting mat, remove completely and discard.
3. Unwrap a new Personal Cutting System™ cutting mat
(purchase at your local retailer). Remove the clear
liner first, and apply to your cutting tray. Smooth
any air bubbles out with your fingers, and apply firm
pressure for good bond.
4. Remove the patterned liner or liner with Top Side
label, to expose the tacky cutting surface.
5. Proceed with normal operation.
(V TIPS
1. Store your Personal Cutting System™ in a secure
location, such as the Personal Cutting System™ Carry
Bag to reduce dust accumulation on the cutting mat.
2. Be sure that the new cutting mat is placed so that the
patterned liner is facing up.
3. If your mat is still tacky, but the blade has cut all the
way through, the mat needs to be replaced or blade
damage could result.
4, Position the new cutting mat in the top left hand
corner-see figure 3.2 — this will insure that your
paper is properly backed during the cutting process.
5. Store unused cutting mats in a cool, dry place. This
will protect their shelf life until ready for use.
Selecting Shapes or Designs to Cut
(Vj TIPS
1.
1. Turn power on.
2. Open dock and insert any design book.
3.
4. Open book, and select any shape by touching the
Load desired paper.
highlighted button corresponding to designs within
the book. Buttons appear as a solid or dashed circle.
The machine will make an audible signal that a shape
was selected.
. Each shape has a number next to the button location
on the Design Book. When pressed, this number will
display on the LCD screen.
. Press the Cut button
Select multiple shapes by pressing each shape once
for each cut desired. Example, touch the same
button twice for two cuts. Touch two different shapes
to cut those shapes on the same paper currently
inserted on the paper/cutting tray.
. You may select as many shapes as desired — When
there are no more cut locations on the paper, the
Personal Cutting System™ will make an audible alert,
and instruct you to start your cut. After the cut is
complete, add more paper, and continue to select
shapes.
Resizing Shapes
Each shape in a Design Book is offered in
three sizes. If a resize button is not selected,
each shape will cut out in its pre-specified
default size. The default size is determined by
what is most usable for all Personal Cutting
System™ owners.
You may resize any shape or font on the
Personal Cutting System™.
A “+” before the number on the LCD indicates
that you have selected to enlarge the shape.
A "-" before the number on the LCD indicates
that you have selected to reduce the shape.
1. Before selecting a shape or design to cut, press the
Enlarge or Reduce button. (fig. 6.1) = D
2. Continue selecting shapes until ready to cut; press the
Cut button.
7 A
ИО АСФ
>
E
(Vj TIPS
1. Select a resizing option before each shape selection.
2. You may select different sizes for different shapes
during the same cutting session. You may continue to
select until the machine fills up the paper with shapes
to cut.
3. Resize different layers of layered designs to create
custom shapes and layouts unique to you.
Deleting Selected Shapes
After each cut is performed, the Personal
Cutting System™ automatically clears
its memory, so that it can accept your next
directions. You may find the need to delete a
selection prior to the cut occurring.
1. After a shape is selected, and you decide to delete it,
press the “trash can” icon on the design book. This
feature acts as a backspace would on a computer
— for each press of the icon, the last shape that was
selected is deleted.
2. Select a new shape, or, press cut to start the machine
on any shapes already selected.
(V TIPS
1. If you want to delete the last shape chosen, use the
“trash can” icon on the design book.
2. If you want to delete all shapes selected, press the
red “cancel” button to the left of the LCD screen.
General Maintenance
Your Xyron Personal Cutting System™ is
designed to be a long-lasting, durable
machine. lt is meant to be handled
frequently, and includes safety features to
keep all users protected, at all times.
In order to function properly, the following
safety features must be engaged.
Top Lid
The top lid must be closed for the Personal
Cutting System™ to operate. If opened during
operation, all cutting is immediately stopped.
To return to its home position, close the lid,
turn machine off then on.
(VTIPS
1. Open the top lid if you need to manually clear material
of the cutting surface, or to clean the machine.
2.The top lid is designed to snap off the machine if too
much force is applied to during handling. The top lid
simply snaps into place at the back hinge to the
machine. No tools are required.
Paper/Cutting Tray
(VTIPS
1. lo remove the tray , press the button on the tray lip
and pull out of the machine.
2. Inserting the tray. The tray will lock the tray into
place for cutting.
When to Replace the Blade
The cutting blade needs to be replaced when
it no longer easily cuts paper. Symptoms of a
dull blade are:
o Blade does not cut through entire shape.
o Blade does not penetrate through paper in some
areas of the shape.
o Shape has noticeable paper fibers on edges, or, rough
on edges.
Blades dull different for each user, based on
several variables. While the Personal Cutting
System” will cut paper stocks up to 80#'s,
or .010"thick doing so on a regular basis will
dull the blade faster than if cutting vellums or
thin scrapbook papers.
Safely discard dull blades by dropping them
in an empty aluminum soda can, or plastic
water bottle. This will insure that the blade
is not handled directly by others after it has
been thrown away.
' WARNING: The blade has a safety guard
that protects you from cutting
yourself while handling. Putting excessive
force on the protective blade cap could cause
the blade cap to retract and expose the tip of
the blade. For your safety, do not intentionally
force this cap open when handling the blade.
Technical Specifications
Drive method
Maximum cutting area
Cutting force
Minimum character size
Loadable number of tools
Blade types
LCD size
Power consumption
Rated power supply
Operating environment
External dimensions
Weight
Maximum Paper thickness
Manufactured in
stepper motors
3.85" x 3.85"
1.8 kg min.
Depends on Design Book
1
45 degree
2.5” x 5/8” (63.5mm x
15.87mm)
AC 100-240V 50/60Hz 1.2A
dedicated power adapter
16V DC 2.3 Amp
25°C
11in x 8.5in x 5.5in
Approximately 5 Ibs
(2.2 kg)
Vellum to 80# cardstock
010" (.3mm)
China
Trouble Shooting Guide
Symptom: Issue: Try This to Fix:
Unit does not e Unit not e Unplug power
turn on. receiving cable, plug
power back into
socket.
e Possible * Unplug power
damage cable to unit,
plug back into
unit
Turn machine
on and off
Contact
Technical
Support if
unit does not
function
Does Not Cut
* Shape book
not inserted
into dock
* Paper tray not
locked into
place
* Top lid open
* Open Top Lid,
unscrew blade,
push down on
blade and hand
tighten screw
e Check for
blade dullness
— see mainte-
nance section
e Shapes may
not yet be se-
lected. Review
LCD Screen to
review selected
shapes.
Trouble Shooting Guide
Symptom:
Issue:
Try This to Fix:
Does Not Cut
* Shape book
not inserted
into dock
* Paper tray not
locked into
place
* Top lid open
* Shape book may
not be properly
inserted.
Remove book,
check for any
debris near
where book
spine contacts
the dock.
Reinsert book
and select
shapes
Shape book
pages may not
be flat on dock.
Open book to
selected page,
and make sure
pages, and
binding of book
lay flat on the
dock.
Check that
paper/cutting
tray is fully
engaged. Tray
should be
locked into
position. Gently
tug on tray to
verify it is fully
locked.
* Check that top
lid is shut.
Trouble Shooting Guide
Symptom:
Issue:
Try This to Fix:
Does Not Cut
® Paper jammed
in blade
housing
* Remove blade,
and inspect the
cutting edge. Do
not retract the
safety cover. If
paper particles are
exposed (jutting
out from under the
safety cover), use
you shape removal
tool to carefully
remove the paper
bits, and return the
blade to the ma-
chine (see instruc-
tions of changing
the blade).
Design Book
does not insert
easily into dock
* Book inserted
incorrectly
e Dirt or refuse
in canal where
design book
rests in dock
Book may be
inserted upside
down - remove
and rotate, try to
reinsert.
Check that no
foreign debris has
collected in the
slot that the spine
of the design
book rests in the
dock. The design
book fits this
canal perfectly,
so, refuse may
interfere with the
book connection.
Trouble Shooting Guide
Symptom: Issue: Try This to Fix:
Blade has * Power was * Check to see if
. . ower cord is
stopped in interrupted E onnected to
cutting area e Blade is power electrical
jammed outlet, and is
e P firmly inserted into
aper has machine
come off e Turn unit off, then
cutting mat on again — blade
. should return to
* Motor is home position
damaged e If you hear the
motor running, but
the blade is not
moving, your blade
may be jammed
— turn machine
off, open lid and
remove paper, close
lid and turn on.
Blade should return
to home position.
Turn machine off,
open lid, remove
paper. Remove
paper/cutting tray
by sliding out of
machine. Turn
machine on. Blade
should return to
home position.
If blade does still
does not move
to home position,
you may have a
damaged motor.
Contact Xyron
Tech Support at :
1-877-392-9474
Trouble Shooting Guide
Symptom: Issue: Try This to Fix:
Lid has ® Too much * The lid breaks
detached from pressure away when too
machine applied to much force is
the lid, while applied to it. To
fix, simply snap
back the hinge
into the channel
of the lid. The
lid will function
nomally when
reinserted.
opened, or,
dropped
If you are unable to isolate and
solve your problem with the
tips above, call Xyron Technical
Support, at
1-877-392-9474
P/N 2489 Rev 3/1
">