Yamaha DVD CHANGER Owner's Manual

Yamaha DVD CHANGER Owner's Manual
UA
DVD CHANGER
LECTEUR DE DVD CHANGEUR
DVD-C740
OWNER’S MANUAL
MODE D’EMPLOI
NATURAL SOUND DVD PLAYER
STANDBY
ON
DISC
PLAY
PROGRESSIVE
1
REPEAT
2
3
4
5
CHANGE
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns the user that uninsulated voltage
within the unit may have sufficient magnitude to cause
electric shock. Therefore, it is dangerous to make
any kind of contact with any inside part of this unit.
WARNING
To reduce the risk of fire or electric shock, do not
expose this appliance to rain or moisture.
CAUTION
Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
radiation exposure.
The set complies with the FCC-Rules, Part 15 and
with 21 CFR 1040.10.
This symbol alerts the user that important literature
concerning the operation and maintenance of this
unit has been included. Therefore, it should be read
carefully in order to avoid any problems.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings.
Install in accordance with the manufacturers
instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety
purpose of the polarized or
grounding-type plug. A polarized plug
AC Polarized
Plug
has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong.The wide blade or the third prong are
provided for your safety.When the provided plug does not
fit into your outlet, consult an electrician for replacement of
the obsolete outlet.
10. Protect the power cord from being walked on or
pinched, particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12.
Use only with a cart, stand, tripod, bracket,
or table specified by the manufacturer or sold
with the apparatus.When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as if the power-supply cord or
plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, or when the apparatus has been
exposed to rain or moisture, does not operate normally, or
has been dropped.
15. Battery usage CAUTION – To prevent battery leakage
which may result in bodily injury or damage to the unit:
Install all batteries correctly, + and - as marked on the unit.
Do not mix batteries (old and new or carbon and
alkaline, etc.).
Remove batteries when the unit is not used for a long time.
EL 6475-E002: 01/3
FCC INFORMATION (for US customers)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly
approved by Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the
USA.
3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class "B" digital devices.
Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not
result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with
FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference,
which can be determined by turning the product "OFF" and "ON", please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial
type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you
can not locate the appropriate retailer, please contact Yamaha Electronics Corp., 6600 Orangethorpe Ave. Buena Park, CA90622.
The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association's Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying
blaring or distortion - and, most importantly, without affecting your sensitive hearing.
Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic
Industries Association's Consumer Electronics Group recommend you to avoid prolonged exposure from excessive
volume levels.
For Customer Use:
CAUTION
- VISIBLE AND INVISIBLE LASER RADIATION
WHEN OPEN. AVOID DIRECT EXPOSURE TO BEAM.
Read carefully the information located at the rear panel of the
player and enter below the Serial No. Retain this information for
future reference.
CAUTION
VISIBLE AND INVISIBLE LASER RADIATION
WHEN OPEN. AVOID DIRECT EXPOSURE TO BEAM.
Model No.
Serial No. __________________________
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
PRODUIT LASER DE CLASSE 1
U.S.A. model
FOR CANADIAN CUSTOMERS
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
PRODUIT LASER DE CLASSE 1
To prevent electric shock, match wide blade of plug to wide slot and
fully insert.
This Class B digital apparatus complies with Canadian ICES-003.
CAUTION
- VISIBLE AND INVISIBLE LASER RADIATION
WHEN OPEN. AVOID DIRECT EXPOSURE TO BEAM.
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the Radio Interference
Regulations of the Canadian Department of Communications.
CAUTION
VISIBLE AND INVISIBLE LASER RADIATION
WHEN OPEN. AVOID DIRECT EXPOSURE TO BEAM.
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
PRODUIT LASER DE CLASSE 1
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
Australia model
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
PRODUIT LASER DE CLASSE 1
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1 To assure the finest performance, please read
2
3
4
5
6
7
8
9
10
11
12
13
this manual carefully. Keep it in a safe place for
future reference.
Install this unit in a well ventilated, cool, dry, clean
place — away from direct sunlight, heat sources,
vibration, dust, moisture, or cold. In a cabinet,
allow about 2.5cm (1 inch) of free space all
around this unit for adequate ventilation.
Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds.
Do not expose this unit to sudden temperature
changes from cold to hot, nor locate this unit in
an environment with high humidity (i.e., a room
with a humidifier) to prevent condensation inside
this unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
Avoid installing this unit in a location where
foreign objects may fall onto this unit or where
this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
– Other components, as they may cause
damage and/or discoloration on the surface
of this unit.
– Burning objects (i.e., candles), as they may
cause fire, damage to this unit, and/or
personal injury.
– Containers with liquid in them, as they may
fall, spilling the liquid and causing an electrical
shock to the user and/or damage to this unit.
Do not cover this unit with a newspaper,
tablecloth, curtain, etc. in order not to obstruct
heat radiation. If the temperature inside this unit
rises, it may cause fire, damage to this unit, and/or
personal injury.
Do not plug in this unit to a wall outlet until all
connections are complete.
Do not operate this unit upside-down. It may
overheat, possibly causing damage.
Do not use excessive force on switches, knobs
and/or cords.
When disconnecting the power cord from the
wall outlet, grasp the plug; do not pull the cord.
Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
Use only the voltage specified on this unit. Using
this unit with a higher voltage than specified is
dangerous and may cause fire, damage to this
unit, and/or personal injury. YAMAHA will not be
held responsible for any damage resulting from
use of this unit with a voltage other than as
specified.
To prevent damage by lightning, disconnect the
power cord from the wall outlet during an
electrical storm.
14 Do not attempt to modify or fix this unit.
Contact qualified YAMAHA service personnel
when any service is needed. The cabinet should
never be opened for any reason.
15 When not planning to use this unit for long
periods of time (i.e., vacation), disconnect the AC
power plug from the wall outlet.
16 Be sure to read the “Troubleshooting” section on
common operating errors before concluding
that this unit is faulty.
17 Before moving this unit, press STANDBY/ON to
set the unit in standby mode, then disconnect
the AC power plug from the wall outlet.
The unit is not disconnected from the AC power
source as long as it is connected to the wall
outlet,even if this unit itself is turned off.This state is
called the standby mode.In this state,this unit is
designed to consume a very small quantity of power.
NOTE:
Pictures shown maybe different between countries.
Never make or change connections with the power
switched on.
LASER SAFETY
This unit employs a laser. Due to possible eye injury,
only a qualified service person should remove the
cover or attempt to service this device.
CAUTION
VISIBLE AND INVISIBLE LASER RADIATION
WHEN OPEN. AVOID EXPOSURE TO BEAM
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
This unit is designed for home use only. Do not use
this unit for business purposes.
Be sure to place this unit on a level surface.
If not so, this unit will fail to work normlly at the
PLAYXCHANGE operation and cause damage to
the disc(s) and this unit itself.
LASER
Type
Wave length
Output Power
Beam divergence
Semiconductor laser GaAlAs
650 nm (DVD)
780 nm (VCD/CD)
7 mW (DVD)
10 mW (VCD/CD)
60 degree
Contents
Supplied accessories ..................................................2
Notes about discs ......................................................2
Cleaning discs..........................................................................2
Symbols Used in this Manual ...................................2
Functional Overview
Front Panel ..................................................................3
Rear Panel ....................................................................4
Remote Control.........................................................5
Preparation
General Notes on connections ..............................6
Digital Connections ...................................................6
Analog Connections.................................................6
Video Connections ....................................................6
S-Video jacks ...........................................................................7
Component Video jacks...................................................7
Composite Video jacks .....................................................7
Inserting batteries into the Remote Control ......8
Using the Remote Control .............................................8
NTSC/PAL Conversion ............................................8
Switching On ...............................................................8
Menu Bars on TV Screen .........................................9
Temporary Feedback Field Icons.................................9
User Preference Settings..........................................9
General operation................................................................9
Picture ......................................................................................10
Sound .......................................................................................11
Language.................................................................................13
Features...................................................................................13
Other Feature......................................................................13
General Features ..................................................... 17
Moving to another title/chapter................................17
Search.......................................................................................17
Slow Motion .........................................................................17
Still Picture and Frame-by-frame playback ..........17
Scan ...........................................................................................17
Repeat......................................................................................18
Repeat A-B............................................................................18
Shuffle Across All Discs..................................................18
Time search ..........................................................................18
Zoom .......................................................................................18
Favorite Track Selection Across Disc ....................19
FTS for a Single disc .........................................................19
MP3 Disc Features .................................................. 20
Album/Title Playback.......................................................21
Repeat track/album/Disc ...............................................21
Access Control
Child Lock................................................................. 22
Activating/deactivating the Child Lock ..................22
Authorising discs ................................................................22
Deauthorising discs...........................................................22
Parental Control...................................................... 22
Activating/Deactivating Parental Control.............23
Country ...................................................................................23
Changing the 4-digit code ............................................23
If you forget your 4 digit code ...................................23
Parental Control Disclaimer ........................................23
Troubleshooting ........................ 24
Specifications ............................. 25
Operation
Basic Playback .......................................................... 14
Playing a DVD-Video.............................................. 14
Playing a title.........................................................................14
Resume....................................................................................14
Video CD and Super Video CD .......................... 15
Playing a disc.........................................................................15
Playing an Audio CD .............................................. 15
Playing a disc.........................................................................15
Special DVD Features ............................................ 16
Title/Disc menu ..................................................................16
Camera Angle......................................................................16
Changing the audio language......................................16
Subtitle Language...............................................................16
Special VCD & SVCD Features............................ 16
Playback Control (PBC).................................................16
Special CD & MP3 Features.................................. 16
CD text and MP3 text ...................................................16
1
English
Introduction
Introduction
Thank you for purchasing this YAMAHA DVD
player. This Owner’s Manual explains the basic
operation of this DVD player.
Supplied accessories
–
–
–
–
Remote control
Batteries (two AA size) for remote control
Audio/Video cable
Owner’s Manual
Symbols Used in this Manual
The below symbols appear in some headings and
notes with the following meanings:
DVD
– Description refers to playback of
DVD-video discs
VCD
– Description refers to playback of
Video CDs
CD
– Description refers to playback of
Audio CDs
Notes about discs
– This unit is designed for use with DVD video,
Video CD, Super video CD, Audio CD (CD text
supported), CD-R and CD-RW (MP3 Supported),
DVD+RW and DVD+R.
– CD-R and CD-RW cannot be played unless
finalized.
– Some discs cannot be played depending on the
disc characteristics or recording conditions.
– Be sure to use only CD-R and CD-RW discs made
by reliable manufacturers.
– Do not use any non standard shaped discs (heart,
etc.)
– Do not use disc with tape, scals, or paste on it,
damage to the unit may result.
– Do not use a disc printed on its surface by a
commercially available label printer.
Helpful Hints!
● Some DVD video discs require specific
functions or allow only limited functions
during playback.
● “ Ä ” may appears on the TV screen
which means that the function is not
available on that specific DVD video disc.
Cleaning discs
● When a disc becomes dirty, clean it with a
cleaning cloth. Wipe the disc from the centre out.
Do not wipe in a circular motion.
● Do not use solvents such as benzine, thinner,
commercially available cleaners, or antistatic spray
intended for analogue records.
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of
Dolby Laboratories.
”DTS” and ”DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
2
This product incorporates copyright protection
technology that is protected by method claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be authorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise authorized
by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
Functional Overview
English
Front Panel
STANDBY/ON
– to switch the player to standby mode
or ON
Disc Tray
– load up to 5 discs on the disc tray
/ OPEN/CLOSE
– to open/close the disc tray
NATURAL SOUND DVD PLAYER
STANDBY
ON
DISC
PLAY
CHANGE
PROGRESSIVE
1
2
3
4
5
REPEAT
DISPLAY
– shows the current status of the player
DISC (1, 2, 3, 4, 5)/LEDs
– to select and directly playback the
preferred disc / each LED flashes green
when button is selected
LEDs
– LED lights up when the cor responding
feature is set to ON
S/Q
– search backward* / go to a previous
chapter or track
R/T
– search forward* / go to the next
chapter or track
B; PLAY/PAUSE
– to star t or interrupt playback
9 STOP
– to stop playback
PLAYXCHANGE
– to change another disc(s) during
playback
* Press button for about two seconds.
3
Functional Overview
Rear Panel
VIDEO OUT - COMPONENT
– connect to COMPONENT VIDEO
input of your AV receiver
VIDEO OUT - VIDEO
– connect to VIDEO (composite)
input of your AV receiver
SUBWOOFER
– connect to an active subwoofer
VIDEO
AC Power Cord
– connect to a standard AC outlet
Progressive / Interlace SELECTOR
(NTSC only)
– to switch between Progressive or
interlace depending on your monitor
SUB WOOFER
Y
PB
480p
480i
R
COAXIAL
PCM
PR
OPTICAL
DIGITAL DTS
DIGITAL OUT
S VIDEO
COMPONENT
VIDEO OUT
SCAN MODE
1
2
AUDIO OUT
VIDEO OUT - S VIDEO
– connect to S VIDEO input of your
AV receiver
AUDIO OUT
– connect to AUDIO inputs of your AV
receiver or stereo system
DIGITAL OUT - OPTICAL
– connect to OPTICAL input of your
AV receiver
DIGITAL OUT - COAXIAL
– connect to COAXIAL input of your
AV receiver
Caution: Do not touch the inner pins of the jacks on the rear panel.
Electrostatic discharge may cause permanent damage to the player.
4
Functional Overview
DISC SKIP
– to select another disc
DIMMER
– to select 4 different
brightnesses for the display
T/C
– select title/chapter
SOUND MODE
– selects required sound mode
Stereo, Dolby Surroundcompatible or 3D sound
English
Remote Control
DISC SKIP
DIMMER
T C
SOUND MODE
1
2
3
4
5
6
7
8
9
RETURN RESUME
MENU
– access menu of a DVD disc
1, 2, 3, 4
– (left/right/up/down) select an
item in the menu
ENTER/OK
– acknowledge menu selection
S
– search backward* / go to a
previous chapter or track
0-9 numerical keys
– select numbered items in a
menu
CD TEXT BIT RATE
0
MENU
ON SCREEN
ENTER
OK
RETURN/RESUME
– go back to previous menu /
continue playback after play
was stopped
B/ I
– switch DVD player ON or go
to standby mode
STOP
PLAY
PAUSE
SUBTITLE
ANGLE
ZOOM
AUDIO
REPEAT
A B
SHUFFLE
SCAN
CD TEXT/BIT RATE
– activate/deactivate CD text if
available on the disc (audio
CDs)
– to display bit rate indicator
during playback (DVD, SVCD)
ON SCREEN
– access or remove player’s
system menu
T
– search forward* / next
chapter or track
STOP ( 9 )
– stop playback
PLAY ( B )
– star t playback
PAUSE ( ; )
– pause playback temporarily /
frame-by-frame playback
REPEAT
– repeat chapter, track, title, disc,
all discs
SUBTITLE
– subtitle language selector
A-B
– repeat a specific segment
ANGLE
– select DVD camera angle
SHUFFLE
– play tracks in random order
SCAN
– play the first 10 seconds of each
track/chapter within a disc
ZOOM
– enlarge video image
AUDIO
– audio language / format /
sampling selector
* Press and hold button for about two seconds.
5
Preparation
General Notes on connections
Never make or change connections with the
power switched on.
● Depending on the equipment you wish to
connect, there are various ways you could
connect this player. Possible connections are
shown in the following drawings.
● Please refer to the manuals of other equipment as
necessary to make the best connections.
● Do not connect this player via your VCR. The
video quality could be distorted by the copy
protection system.
● Do not connect this player’s audio out jack to the
phono in jack of your audio system.
Digital Connections
This player has COAXIAL and OPTICAL digital
out jacks. Connect one or both of them to your
AV receiver equipped with Dolby digital, DTS, or
MPEG decoder using each specific cable (separate
purchase).
Notes:
– If the audio format of the digital output does not
match the capabilities of your receiver, the receiver
will produce a strong, distorted sound or no sound at
all. Make sure to select the appropriate audio
format at menu screen included on the disc.
Pressing AUDIO once or more may change not only
audio languages but also audio formats, and the
selected format appears for several seconds on the
status window.
– MP3 Audio is not available on the Digital Output.
Analog Connections
Use audio/video cable supplied with this player to
connect the AUDIO OUT L (left) and R (right)
jacks to corresponding input jacks of your audio
equipment such as Stereo amplifier. You can
connect a subwoofer to the SUBWOOFER jack.
VIDEO
SUB WOOFER
Y
PB
480p
480i
R
COAXIAL
S VIDEO
DIGITAL OUT
Y
PR
OPTICAL
PCM
DIGITAL
DTS MPEG
PR
PCM
DIGITAL
DTS MPEG
S VIDEO
DIGITAL OUT
2
AUDIO OUT
R
L
R
L
480p
480i
R
OPTICAL
SCAN MODE
1
VIDEO OUT
PB
COAXIAL
COMPONENT
SCAN MODE
COMPONENT
VIDEO OUT
1
2
AUDIO OUT
O
C
COAXIAL
IN
OPTICAL
IN
AV receiver
Subwoofer
Stereo
amprifier
1
R
CD/DVD
L
Speakers
Left
speaker
You will need to set this player’s digital
output to ALL (see ‘User Preference
Settings’).
6
Right
speaker
Video Connections
If your AV receiver has video output jacks,
connect your receiver (and then to your TV) so
that you can use one TV for several different
video sources (LD, VCR etc.) by simply switching
the input source selector of your receiver.
The player has three types of video output jacks.
Use one of them in accordance with the input
jacks of the equipment to be connected.
Preparation
S (separate) video connection achieves a clearer
picture than composite video connection by
separating color and luminance when transmitting
signals. Use commercially available S-video cable.
Receiver (and TV) with S-video input is required.
Use commercially available coaxial cables.
Receiver (and TV) with component input is
required. Observe the color of each jack when
connecting. If your receiver does not have
component output jacks, connecting the player’s
component output directly to your TV’s
component input can reproduce better video
image.
Component Video jacks <B>
Component video connection achieves high
fidelity in reproducing colors (better performance
than S-video connection), separating video signal
into luminance (Y, terminal color-coded as green),
and color difference (Pb, blue/Pr, red).
Composite Video jacks <C>
Use audio/video cable supplied with this player
when connecting the player to a TV.
VIDEO
SCAN MODE selector
This switch will change the type of NTSC signal
output from the Pr/Cr Pb/Cb Y VIDEO OUT on
the player.
SUB WOOFER
Y
PB
480p
480i
R
COAXIAL
PR
OPTICAL
PCM
DIGITAL
DTS MPEG
S VIDEO
DIGITAL OUT
SCAN MODE
1
COMPONENT
VIDEO OUT
2
AUDIO OUT
480p:
Select progressive when you have a TV that can
accept progressive signals to enjoy accurate
colour reproduction and high quality images.
480i:
Select this setting when connected to a standard
(interlace format) TV.
CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE
FULLY COMPATIBLE WITH THIS PRODUCT
AND MAY CAUSE ARTIFACTS TO BE
DISPLAYED IN THE PICTURE. IN CASE OF 525
PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS
RECOMMENDED THAT THE USER SWITCH
THE CONNECTION TO THE “STANDARD
DEFINITION” OUTPUT. IF THERE ARE
QUESTIONS REGARDING OUR VIDEO
MONITOR COMPATIBILITY WITH THIS
MODEL 525P DVD PLAYER, PLEASE CONTACT
OUR CUSTOMER SERVICE CENTER.
SCAN MODE
Selector
V
S
<A>
<B>
PR/CR
S VIDEO
PB/CB
<C>
Y
COMPONENT
VIDEO
VIDEO
AV receiver
S VIDEO
OUT
COMPONENT
VIDEO OUT
VIDEO
OUT
S VIDEO
IN
COMPONENT
VIDEO IN
VIDEO
IN
This unit is compatible with the complete line of
YAMAHA projectors, including the DPX-1, LPX500, PDM-1 and DPX-1000.
7
English
S-Video jacks <A>
Preparation
Inserting batteries into the
Remote Control
+
+
3
-
CAUTION!
– Remove batteries if they are exhausted or
not to be used for a long time.
– Do not use old and new or different types
of batteries in combination.
– Batteries contain chemical substances, so
they should be disposed off properly and
kept away from children.
Using the Remote Control
● Direct the remote control at the remote sensor
of the player.
● Do not drop the remote control.
● Do not leave the remote control near extremely
hot or humid places.
● Do not spill water or put anything wet on the
remote control.
8
DVD discs are recorded according to color
system eg. NTSC and PAL. Your TV also operates
according to a color system.
This DVD player is compatible with NTSC and
PAL. To play on this DVD player, the color
system of the DVD disc, the TV and the DVD
player should match. If all three are not the same,
the DVD may play in only black and white, the
picture may roll continuously or the picture may
appear distorted.
To activate the conversion, refer to page 11.
Open the battery cover.
Insert batteries (AA size) with the correct polarity
as indicated by the + and - symbols inside the
battery compartment.
Close the cover.
-
1
2
NTSC/PAL Conversion
Switching On
1
2
3
4
Connect the AC power cord to the power outlet.
Switch on the TV and DVD player.
Select the correct input channel at your TV and
set the input source at your AV receiver to DVD.
➜ The player display lights up and the default
screen appears on the TV.
If you are using an external equipment (eg. audio
system or receiver), turn them on and select the
appropriate input source that was used to
connect to the player output. Refer to the
equipment owner’s manual for detail.
Note:
– If you do not have a proper picture or sound, refer
to ‘Troubleshooting’ section.
Preparation
English
Temporary Feedback Field Icons
Menu Bars on TV Screen
These icons will appear on the top left hand
corner of your TV screen.
● Operations can be carried out directly via the
multiple menu bars on the TV screen.
● The following functions are available via the menu
bars. Pressing ON SCREEN repeatedly will toggle
through menu bar 1, menu bar 2, menu bar 3 and
menu bar OFF:
Scan
Repeat A to end
Repeat all discs
Repeat A–B
Repeat disc
Angle
Repeat Title
Child Lock On
Repeat Track
Child Safe
Menu bar 1
From the left,
User Preference Settings ➜
Current Subtitle Language ➜
Current Audio Language ➜ Smart Color ➜
Sound Mode
The following functions are available with
activated disc via the menu bars:
Repeat Chapter
Resume
Shuffle all discs
Action Prohibited
Shuffle
Movie only
Shuffle Repeat
Music only
PlayXchange
Menu bar 2
User Preference Settings
In the User Preference Settings menu, you can
customize your player to suit your own particular
requirements.
From the left,
Frame by Frame ➜ Slow Motion ➜ Scan Speeds
➜ Camera Angle ➜ Enlarge Picture
Menu bar 3
From the left,
Disc ➜ Title ➜ Chapter ➜ Time Search ➜
Favorite Track Selection
General operation
1
2
3
1
2
3
1
2
Press ON SCREEN on the remote control.
The
will be highlighted in the menu bar.
Press 4 to activate the Personal Preferences
menu.
To select a preferred menu language,
Press 4 until r is highlighted.
Press 2 to enter the submenu and 4 to choose
Menu language.
Use 3/4 to select your preferred menu language.
For navigation and selection in Personal
preferences,
Use 1, 2, 3, 4 to toggle through the functions
and select your preferred option.
Press ENTER/OK to confirm a highlighted
selection.
The following items are available:
9
Preparation
Picture
– TV Shape
Select the aspect ratio of the TV to be connected.
16:9 ➜ when you connect a wide-screen TV to
this player.
4:3 LETTER BOX ➜ when you connect a
normal TV to this player. Displays a wide picture
with black bands displayed on the upper and
lower portions of the TV screen.
4:3 PAN SCAN ➜ when you connect a normal
TV to this player. Displays the wide picture on the
whole TV screen with a portion automatically cut
off.
– Monitor Type
Allows you to select the type of display device
that is connected to this unit.
In each device, a set of predefined Colour settings
is available or choose Personal that allows you to
select the colour settings according to your
preference.
1en
1en
1
2
TV shape
1 TV
Black Level shift
2 Plasma TV
Monitor Type
3 Projector
Video shift
4 Projection TV
– Video shift
Use this setting to personalize the position of the
picture on your TV by scrolling it to the left or
right.
16:9
4:3
Letter Box
1en
1en
1
2
TV shape
Black Level shift
Monitor Type
4:3
Pan Scan
Video shift
Note:
– Pan Scan is subject to availability on the disc.
– Black level shift (NTSC output only)
Select On for adapting the color dynamics to
obtain richer contrasts.
1en
1en
1
TV shape
10
Black Level shift
On
Video shift
Off
2
OK to exit
– Color settings
You can select one of five predefined sets of color
settings and one set (Personal) which you can
define yourself.
1en
1en
1
TV shape
1 Personal
Black Level shift
2 Rich
Video shift
3 Natural
Colour settings
4 Soft
2
● When Personal is selected it allows you to finetune saturation, brightness and contrast.
● Use 3 or 4 to adjust the values of these
parameters. Press ENTER/OK or 1 to exit.
Preparation
Disc
Type
1
2
Format
Output format
Selected mode
PAL
NTSC
AUTO
PAL60
NTSC
NTSC
DVD
NTSC
PAL
Not
Supported
PAL
PAL
VCD
NTSC
NTSC
PAL60
NTSC
PAL
NTSC
PAL
PAL
In the Personal Preferences Menu, select TV
System.
Press 3 or 4 to select PAL, NTSC or AUTO.
Notes:
– If you have a PAL only TV, ensure that your TV
System setting is PAL.
– AUTO can only be selected when using a TV that
supports both the NTSC and PAL systems
(multisystems).
– This setting is applicable for CVBS output on cinch
only.
– Slight picture distortions may occur due to this
conversion. This is normal. Thus, the AUTO format
is most suitable for the best picture quality.
Sound
– Digital output
● Digital output selection enables you to specify the
type of digital output suitable for your receiver.
● Select ALL (default setting), if you had connected
your DIGITAL AUDIO OUT to a multichanel
decoder receiver.
● Select PCM only if your receiver is not capable of
decoding compressed/encoded input stream.
● Select OFF to deactivate the DIGITAL AUDIO
OUT.
Note:
– Digital output is not available for MP3 discs.
1en
1en
1
Digital output
Off
Analog output
PCM only
Night mode
All
2
– Analog output
Select Stereo, Dolby Surround-compatible or 3D
Sound.
Stereo: In this setting, the 5.1 audio channels are
down-mixed to a stereo signal. Select this setting
when connecting to a TV, stereo amplifier/
receiver, etc.
11
English
– TV System (NTSC/PAL Conversion)
Allows you to select between PAL, NTSC and
AUTO mode depending on your TV.
The conversions supported are as follows:
Preparation
Dolby Surround-compatible: Select this setting
when using an equipment with a Dolby Surround
Pro Logic decoder. In this setting, the 5.1 audio
channels (Dolby Digital, MPEG-2, DTS) are
downmixed to a Dolby Surround-compatible 2channel output.
3D-Sound: In a setup without rear speakers
(analog stereo output), 3D Sound remixes the six
channels of digital surround into a two-speaker
output while retaining all of the original audio
information. The result is the listening sensation of
being surrounded by multiple speakers.
During DVD or Video-CD playback, these values
can be selected directly with SOUND MODE.
1en
1en
1
2
Digital output
Analog output
Stereo
Night mode
Dolby Surr-compat
Karaoke vocal
3D sound
– Night Mode
When set to ON, the dynamics of your sound
output are optimized. High volume outputs are
softened, enabling you to watch your favorite
action movie, etc. without disturbing others.
– Karaoke vocal
Put this setting to ON only when a multi-channel
karaoke DVD is being played. The karaoke
channels on the disc will then be mixed into a
normal stereo sound.
12
– PCM Output
Allows to select PCM digital output between
48kHz and 96kHz. When 48kHz has been
selected, 96kHz PCM data, (if available on disc)
will be converted to 48kHz.
Some 96kHz DVD are copy protected. If your
PCM output selection is 96kHz, the digital output
is downsampled to 48KHz.
– Sub-woofer Cut-off
The frequency of the subwoofer output can be
set to High (200Hz) or Low (100Hz) to match
your system’s playback sound quality.
Preparation
Selecting disc languages:
Menu/Audio/Subtitle language
● This is to select the audio language, subtitle
language and the language used in TV screen
menus or DVD menus which will always be used
for every disc to be played back.
● If the language selected is not available on the disc,
the default language designated by each disc will
be selected.
Features
– Access Control
Access Control contains the following features:
Child Lock - When Child Lock is set to ON, a 4digit code needs to be entered in order to
playback discs.
Parental control - Allows the conditional
presentation of DVDs containing Parental
Control information (see ‘Access Control’ section).
– Status Window
Displays the current status of the player and
appears with the menu bar. When disc playback
is stopped, it is displayed with the ‘Temporary
Feedback Field’ in the default screen. See ‘OnScreen Display’ information;
Factory setting is ON. Select OFF to suppress
display of the Status Window.
– Smart Power OFF
Puts the set to standby after a predefined time.
This can be set to Enabled or Disabled.
– Wake-up Timer
The wake-up timer allows your player to turn on
after a preset time. Whenever the player wakes
up, the value of wake up timer is set to zero
automatically. The Wake-up Timer will activate
when the set is switched to standby-mode.
Beeper
Help text
Smart Power off
Wake up timer
450
480
510
540
– IntelliPlay
Intelliplay is a convenient feature for automated
playback of disc content.
When switched to “ON”, the playback will
automatically play only disc with similar content
(either audio or video) to previous disc while
skipping the rest content.
For example, when a CD was played previously,
the player will search for the next audio disc in the
tray sequence (CD or MP3 disc). (→ Music only)
Pressing the Disc Direct Access to a disc other
than a music disc when IntelliPlay is set to ON, will
change to video mode. (→ Movie only)
IntelliPlay
On
Off
Other Feature
– PBC (Playback Control - for VCD)
The Playback Control can be set to ON or OFF
(see section “Special VCD & SVCD Features” for
details).
– Bit Rate Indicator
Press CD TEXT/BIT RATE to activate the bit rate
indicator. When activated, the bit rate for video
and audio, as well as the total bit rate is displayed.
This is only applicable during playback of
DVD and SVCD discs.
– Beeper
The beeper can be set to ON or OFF.
– Help text
When set to ON, help text describes the icons
selected. Select OFF if you no longer require the
help text.
13
English
Language
Operation
Basic Playback
1
2
3
4
5
Playing a DVD-Video
Press STANDBY/ON on the front panel.
Press OPEN/CLOSE / on the front panel to
open disc loading tray.
Place the chosen discs in the tray, with the label
facing up.
Press PLAY B.
➜ The disc tray closes and playback starts
automatically with all the loaded discs on the tray
in sequence.
To stop playback, press STOP.
NATURAL SOUND DVD
● DVD video discs may have one or more TITLES,
and each TITLE may have one or more
CHAPTERS.
● Playback stops at the end of each TITLE.
DVD-VIDEO DISC
TITLE 1
CHAPTER 1
CHAPTER 2
TITLE 2
CHAPTER 1
CHAPTER 2
CHAPTER 3
PLAYER
Playing a title
STANDBY
ON
PLAY
DISC
CHANGE
MULTI CH
1
2
3
4
5
REPEAT
● To playback a specific disc directly, press DISC
SKIP repeatedly on the remote control or one of
the DISC (1, 2, 3, 4, 5) on the front panel.
● Press PLAYXCHANGE on the front panel to
open the disc tray and reload or unload any discs
without interrupting current disc playback.
● Playback will stop after all discs have been played.
● When the disc tray is open, pressing PLAY,
OPEN/CLOSE, PLAYXCHANGE, DISC (1, 2, 3,
4, 5) will close the disc tray automatically.
Notes:
– DVDs may have a region code. Your player will
not play discs that have a region code different from
the region code of your player. The region code of
this player is stated on the rear panel.
– If ‘Child Lock’ is set to ON and the disc inserted
is not authorized, the 4-digit code must be entered
and/or the disc must be authorized (see ‘Access
Control’).
1
2
3
4
Press DISC (1, 2, 3, 4, 5) on the front panel or
DISC SKIP repeatedly on the remote control to
playback a specific disc directly.
➜ Playback starts automatically.
When the MENU appears on the TV screen, use
4, 3, 1, 2 or numerical keys on the remote
control to select an option and continue playback.
If the titles are numbered , press the numerical
keys or use 3/4 to select desired title in the
menubar.
To stop playback, press STOP.
Resume
The playback of a disc can be interrupted at any
point and then resumed from the point where the
playback was last stopped.
1
Press STOP to interrupt playback.
➜ The help line text appears “Press Stop again to
start from beginning” for 5 seconds.
2 Pressing PLAY will automatically resume playback
from the point where playback was interrupted.
OR
● Press STOP again and then press PLAY,
➜ Playback will starts from the beginning of the
discs.
● If you press PLAY when resume icon appears on
the screen, resume playback starts from the point
where playback was interrupted.
Note:
– Resume feature is also applicable to VCDs and
SVCDs.
14
Operation
The current VCD 2.0 and Super Video CD 1.0
standard features are:
Support following VCD and SVCD formats:
Features
Video
bit rate
resolution NTSC
resolution PAL
Video CDs 2.0
MPEG-1
constant 1,150 Kbps
352x240, 29.97Hz
352x288, 25Hz
Super Video CDs 1.0
MPEG-2
variable up to 2.6 Mbps
480x480 interlaced, 29.97Hz
480x576 interlaced, 25Hz
Still picture (photo)
resolution NTSC
resolution PAL
MPEG-1
352x240, 704x480
352x288, 704x576
MPEG-2 (1 Frame)
480x480, 704x480
480x576. 704x576
Audio
sampling
bit rate
audio channels
surround sound
MPEG-1 layer II
44.1KHz
224Kbps
1 stereo / 2 mono
Stereo with Dolby Pro-Logic
MPEG-1 layer II
44.1KHz
32-384Kbps
< 2 stereo / 4 mono
MPEG-1 (5+1) extension
Overlay graphics/text
sub-channels
coding
overlay video plane
<= 4
4 colour CLUT (2bits/pixel)
Playing an Audio CD
● Audio CDs contain only TRACKS.
● They can be played on your DVD player with the
audio output connected to a stereo system or to
your TV.
● If CD-text is available on the disc, it will be
displayed on both the TV screen and player’s
front display.
● Select tracks using the menubar on the TV screen
or by pressing the numerical keys directly.
● Your DVD player also allows you to compile
Favorite Track Selection (FTS) programs for your
discs by selecting or excluding tracks of your
choice (see FTS Program - Audio CDs).
Following formats can’t be supported in
VCD:
– HQ-VCD is encoded at 2.4Mbps or 2.6Mbps
– XVCD (eXtended VCD) with higher resolution
and data rate.
● Video CDs may have one or more TRACKS, and
TRACKS may have one or more INDEXES.
● To make easy and convenient access, you can
move between TRACKS and INDEXES.
● Some Video CDs have Play Back Control (PBC),
which is a predefined playback sequence stored
on the disc (see “Playback Control” section).
AUDIO CD
TRACKS
1
2
TRACK 1
INDEX 2
TRACK 2
INDEX 1
INDEX 2
INDEX 3
3
4
5
6
7
8
9 10 11 12 ...
Playing a disc
1
VIDEO CD
INDEX 1
2
3
Press DISC (1, 2, 3, 4, 5) on the front panel or
DISC SKIP repeatedly on the remote control to
playback a specific disc directly.
➜ Playback starts automatically.
➜ The TV screen will display the number of
tracks for selection and current playing status.
At the end of the disc, playback of the next
available disc starts. Playback stops after all the
discs are played back.
To stop playback, press STOP.
Playing a disc
1
2
3
Press DISC (1, 2, 3, 4, 5) on the front panel or
DISC SKIP repeatedly on the remote control to
playback a specific disc directly.
➜ Playback starts automatically.
➜ The current track number and its elapsed
playing time will be displayed.
To stop playback, press STOP.
Disc Resume feature is also applicable for VCDs
and SVCDs (see “Resume” section).
15
English
Video CD and Super Video CD
Operation
Special DVD Features
Special VCD & SVCD Features
DVDs may contain menus to navigate the disc
and access special features. Press the appropriate
numerical key or use 4, 3, 2, 1 to highlight your
selection in the DVD menu and press ENTER/OK
to confirm.
Playback Control (PBC)
Playback control is a feature on some Video CDs
/ Super Video CDs that enables interactive use.
Video CD discs with Playback Control features
enables user to access a selected track directly
from the menu.
Title/Disc menu
1
2
3
Press MENU.
➜ If the current title has a menu, the menu will
appear on the screen. Otherwise, the menu will
be displayed.
If menu is available on the disc, audio language,
subtitle options, chapters for the title and other
options will appear for selection.
To remove the title/menu, press MENU again.
1
2
3
4
5
Camera Angle
Some discs contain scenes which have been shot
simultaneously from various angles.
This DVD player allows you to select the desired
camera angle.
● When the DVD player encounters a scene shot
in multiple angles, it will give an indication on the
“Temporary Feedback Field.”
➜ The angle icon remains displayed until multiple
angles are no longer available.
● Use 3/4 to select the required angle.
➜ Playback changes to the selected angle.
● You can also select } in the menu bar or press
ANGLE on the remote control directly.
Special CD & MP3 Features
CD text and MP3 text
1
2
3
Changing the audio language
1
2
Select Y in the menu bar or press AUDIO on the
remote control directly.
Press AUDIO or 3/4 repeatedly to select the
different languages.
Load a Video CD with PBC and press PLAY.
Go through the menu with the keys indicated on
the TV screen until your chosen passage starts to
playback. If a PBC menu consists of a list of tracks,
you can select a track directly.
Enter your choice with the numerical keys.
Press RETURN/RESUME to go back to the
previous menu, if applicable on the menu.
You may also select PBC OFF under Personal
Preferences.
➜ When set to OFF, PBC menus are not
activated for further playback.
4
Some CD or MP3-CD discs may contain text
information (eg. track name, album name, artist
name etc.) which will appear on the player and TV
screen during playback.
By default, CD text display is set to ON.
To switch off the CD text display, press CD
TEXT/BIT RATE on the remote control during
playback.
Press CD TEXT/BIT RATE on the remote control
again to switch on the text display mode.
CD
play
Subtitle Language
1
2
16
Select Z in the menu bar or press SUBTITLE on
the remote control directly.
Press SUBTITLE or 3/4 repeatedly to select the
different subtitles.
Audio Disk Mode
track
time
total tracks
total time
11
2.34
14
5.29.78
Disc
The Best of Me
Artist
Bryan Adams
Track
Everything I do
Operation
Note:
– Unless stated, all operations described are based
on remote control use. Some operations can be
carried out using the menu bar on the TV screen.
1
Moving to another title/chapter
3
4
DVD
VCD
When a disc has more than one title/track or
chapter, you can move to another title/chapter as
follows:
1
2
Press ON SCREEN, then select W or X in the
menu bar.
Press 3/4 or the numerical keys to select a title/
chapter.
CD
1
2
3
Press T or S briefly during playback to go
to the next track or to return to the beginning of
the currect track respectively.
Press Stwice briefly to step back to the
previous track.
To go directly to any track, enter the track
number using the numerical keys.
Search
DVD
1
2
3
4
VCD
Select
in the menu bar and press 4.
Use 1/2 to select the required speed: –32, –8 or
–4 (backward), or +4, +8, +32 (forward).
Select 1 to play the disc at normal speed again.
To exit the Search mode, press 3.
2
5
VCD
Select
in the menu bar and press 4.
➜ Playback will pause.
Use 1/2 to select the required speed: –1, –1/2,
–1/4 or –1/8 (backward), or +1/8, +1/4, +1/2 or
+1 (forward).
Select 1 to play the disc at normal speed again.
If ; is pressed, the speed will be set to zero
(PAUSE).
To exit slow motion mode, press 3.
(Playback continues at the selected speed.)
Still Picture and Frame-by-frame
playback DVD VCD
1
Select
in the menu bar and press 4.
➜ Playback will pause.
2 Use 1/2 to select the previous or next picture
frame.
● Press PLAY to play the disc at normal speed again.
Note:
– You can also activate frame-by-frame playback by
pressing PAUSE repeatedly on the remote control.
Scan DVD VCD
1
2
CD
Scanning plays the first 10 seconds of each
chapter/track on a disc.
Press SCAN.
To continue playback at your chosen chapter/
track, press SCAN again or press PLAY.
CD
● To search forward or backward through different
speeds, you can also hold down T or S for
more than two seconds.
17
English
Slow Motion DVD
General Features
Operation
Repeat
Shuffle Across All Discs
DVD
Shuffle feature plays all tracks on all loaded discs
on the disc tray in random sequence.
Press SHUFFLE repeatedly during playback.
➜ SHUFFLE, SHF ALL DSC, SHUFFLE OFF
appears continuously on the front display for
about 3 seconds.
Notes:
– DVD Discs will not be included in the "Shuffle
across all discs" sequence.
– With VCD 2.0, set the PBC (Playback Control) to
Off.
Repeat chapter/title/disc
Each time you press REPEAT, the front display
changes as follows;
REPEAT CHPT
REPEAT OFF
1
REPEAT TITL
RPT ALL DSC
REPEAT DISC
REPEAT CHPT*: repeat the current chapter
REPEAT TITL: repeat the current title
REPEAT DISC*: repeat the entire disc
RPT ALL DSC: repeat all discs loaded on the tray
REPEAT OFF: exit repeat mode
* This feature may not be available with some
discs.
VCD
CD
Time search DVD
1
Repeat track/disc
Each time you press REPEAT, the front display
changes as follows;
REPEAT TRK
REPEAT DISC
REPEAT OFF
RPT ALL DSC
REPEAT TRK: repeat the current track
REPEAT DISC: repeat the entire disc
RPT ALL DSC: repeat all discs loaded on the tray
REPEAT OFF: exit repeat mode
2
3
Note:
– When only one disc is available on the disc tray,
continuous playback will apply when RPT ALL DISC
is selected.
Repeat A-B DVD VCD
1
2
3
CD
– DVD-Video Discs: repeat a sequence in a
title
– Video and Audio CDs: repeat a sequence
in a disc
Press A-B at your chosen starting point.
Press A-B again at your chosen end point.
➜ REPEAT A B appears briefly on the front
display, and the repeat sequence begins.
To exit the sequence, press A-B.
Select
in the menu bar and press 4.
➜ Playback will pause.
➜ The elapsed playing time is displayed in a time
edit box.
Enter hours, minutes and seconds from left to
right in the time edit box using the remote control
numerical keys.
➜ Each time an item has been entered, the next
item will be highlighted.
Press ENTER/OK to confirm the selected time.
➜ The time edit box will disappear and playback
starts from the selected time position on a disc.
1
3
1
off
0:00:34
4
Press ON SCREEN to remove the menu bar.
Zoom DVD
VCD
The Zoom function allows you to enlarge the
video image and to pan through the enlarged
image.
1
2
3
18
VCD
The Time Search function allows you to start
playing at any chosen time on a disc.
Select .
Press 3/4 to activate the ZOOM function and
select the required zoom factor: 1.33 or 2 or 4.
➜ Playback will continue.
➜ The selected zoom factor and ‘Press OK to
pan’ appears below the menu bar.
➜ The zoomed picture will appear on the TV
screen.
Press ENTER/OK to confirm the selection.
➜ The panning icon appears on the screen.
Operation
6
Use 1, 2, 3, 4 to pan across the screen.
When ENTER/OK is pressed only the panned
picture will be shown on the screen.
To exit ZOOM mode, select zoom factor to
“Off” (zoom factor 1) in the menu bar.
off
1
1
no
1
2
3
2
press OK to pan
Storing album/title
Press 4 to select ALBUM/TRACK. Albums are for
MP3 discs and Tracks for (S)VCD.
Use 2 and 1 to select the require Album/Track.
Press ENTER/OK to store the entire selected
Album/Track.
➜ The Album/Track. number will be added to
the program list.
● This FTS function allows you to create a list
favorite tracks by selecting tracks from different
discs available in the disc tray.
● The supported discs are CDDA, MP3, VCD,
SVCD.
● Favorite Track Selection (FTS) list contains up to
100 elements across all the discs on the tray.
4
Storing track/chapter
Press 4 on the selected TRACK/INDEX. Tracks
are for MP3/CDDA discs and Index for S(VCD).
➜ The track/chapter number will be highlighted.
Use 2 and 1 to select the required Track/Index.
Press ENTER/OK to confirm the selection.
➜ The selected Track/Index will be added to the
program list.
Press ON SCREEN to exit the FTS menu.
1
2
3
Switching a Program OFF
Use 3/4 to move to FTS.
Press 2 or 1 to select OFF.
Press ON SCREEN to exit.
Storing a Program
Press OPEN/CLOSE and load preferred discs
onto the disc tray.
In STOP mode, select FTS in the menu bar.
Press 4 in the menu bar.
➜ The FTS window menu appears.
Select All Discs option.
1
Storing entire disc as the FTS
Press 4 to select DISC.
Use 2 and 1 to select the require disc list for all
the loaded discs in the disc tray.
Press ENTER/OK to store the entire disc
selection.
1
Note:
– ZOOM mode gets deactivated when starting
playback of next element in FTS across disc and
Shuffle across Disc modes.
1
2
3
Favorite Track Selection Across Disc
1
2
3
4
1
2
3
2
3
4
5
2
3
Erasing a selection in a Program
While playback is stopped, select FTS in the menu
bar.
Use 4 to select PROGRAM.
Use 2 and 1 to select the required number.
Press ENTER/OK to erase the selection.
Press ON SCREEN to exit.
Erasing all selections
While playback is stopped, select FTS in the menu
bar.
Use 4 to select CLEAR ALL and press ENTER/
OK.
➜ All selections will be erased.
Press ON SCREEN to exit.
Note:
– Pressing PLAYXCHANGE or OPEN/CLOSE during
playback will erase the selected Program if any.
– With VCD 2.0, set the PBC (Playback Control) to
Off.
FTS for a Single disc
1
2
3
Select FTS in the menu bar.
Press 4 in the menu bar.
➜ The FTS window menu appears.
Select CURRENT DISC option.
19
English
4
5
Operation
1
2
3
Storing album/title
Press 4 to select ALBUM/TRACK. Albums are for
MP3 and Tracks for (S)VCD.
Use 2 and 1 to select the require Album/Track.
Press ENTER/OK to store the entire selected
Album/Track.
➜ The Album/Track number will be added to
the program list.
4
Storing track/chapter
Press 4 on the selected TRACK/INDEX. Tracks
are for MP3/CDDA and Index for (S)VCD.
➜ The track/chapter number will be highlighted.
Use 2 and 1 to select the required Track/Index.
Press ENTER/OK to confirm the selection.
➜ The selected Track/Index will be added to the
program list.
Press ON SCREEN to exit the FTS Menu.
1
2
Switching a Program OFF
Use 3/4 to move to FTS.
Press 2 or 1 to select OFF.
1
2
3
1
2
3
4
5
1
2
3
Erasing a selection in a Program
While playback is stopped, select FTS in the menu
bar.
Use 4 to select PROGRAM.
Use 2 and 1 to select the required number.
Press ENTER/OK to erase the selection.
Press ON SCREEN to exit.
Erasing all selections
While playback is stopped, select FTS in the menu
bar.
Use 4 to select CLEAR ALL and press ENTER/
OK.
➜ All selections will be erased.
Press ON SCREEN to exit.
CDDA
20
ANY
MP3 Disc Features
●
●
●
●
●
●
●
●
●
●
Support following MP3-CD formats (Joliet
format):
Max. 64 characters (file names or directory)
Max. nested directory is 8 levels
The max. album (directory) number is 100
Supported VBR bit-rate
Supported sampling frequencies for MP3 disc are:
32 kHz, 44.1 kHz, 48 kHz
Supported Bit-rates of MP3 disc are: 32, 64, 96,
128, 192, 256 (kbps)
Following formats can’t be supported
The files like *.WMA, *.AAC, *.DLF, *.M3U, *.PLS
Chinese filenames
The non-session closed discs
The discs recorded under UDF format
Downloading MP3 files from the Internet or
copying songs from your own legal discs is a
delicate process.
Sound
Quality
Bit Rate
AM radio
32 kbps
64 kbps
Approximate Approximate total
Reduction Ratio
MP3-CD time
40 : 1
40 hrs
20 : 1
20 hrs
Near-CD
96 kbps
15 : 1
15 hrs
CD-like
128 kbps
10 : 1
10 hrs
CD*
256 kbps
5 :1
5 hrs
CD*
320 kbps
3 :1
3 hrs
FM radio
Comment
Sound quality significantly affected
– not recommended
Balanced sound quality
– compression rate
Compression rate low
– suggest to play CDs instead
You may experience an occasional “skip”
while listening to your MP3 files. This is
normal.
Additional note for MP3 disc Playback:
– In compliance with the SDMI, digital-out is
muted while playing MP3 discs.
– Due to the recording nature of Digital Audio
MP3 (DAM),only Digital Audio music will play.
– The disc reading time may exceed 10 seconds
due to the large number of songs compiled
onto one disc.
– Playback of multi-session disc is supported for
the first 10 sessions with the same format.
– For multi-session discs with different formats,
only the first session will be available.
– Some MP3 discs cannot be played depending
on the disc characteristics or recording
conditions.
Operation
English
Album/Title Playback
This feature allows you to view and select the
next or previous MP3 disc Album/Title.
1
2
3
Press 3/4 to scroll through the previous or next
Album.
Press 1/2 to scroll through the previous or next
Track.
You can also select the desired album/track
number directly using the numeric keys on the
remote control.
Notes:
– In STOP mode: numbers are used for album
selection.
– In PLAY mode: numbers are used for track
selection.
● Only the following functions are possible for MP3
discs:
– STOP / PLAY / PAUSE
– SKIP NEXT / PREVIOUS
– REPEAT (TRACK / ALBUM / DISC / ALL
DISCS)
– SHUFFLE ACROSS ALL DISC
– FTS ACROSS ALL DISC
Repeat track/album/Disc
Each time you press REPEAT, the front display
changes as follows;
REPEAT TRK
REPEAT OFF
REPEAT ALBM
RPT ALL DSC
REPEAT DISC
REPEAT TRK: repeat a track
REPEAT ALBM: repeat an album
REPEAT DISC: repeat the current disc
RPT ALL DSC: repeat all discs loaded on the tray
REPEAT OFF: exit repeat mode
21
Access Control
Child Lock DVD
– Double-sided DVDs and multi-volume VCDs may
have a different ID for each side. In order to make
the disc ‘child safe’, each side has to be authorized.
VCD
Activating/deactivating the Child
Lock
1
2
3
4
5
6
7
When disc playback is stopped, select ACCESS
CONTROL in the Personal Preferences menu
using 3/4.
Enter a 4-digit code of your own choice twice.
Move to “CHILD LOCK” using 3/4.
Move to Ç / É using 2.
Select Ç using 3.
Press ENTER/OK or 1 to confirm, then press ON
SCREEN to exit the Personal Preferences menu.
➜ Now unauthorized discs will not be played
unless the 4-digit code is entered.
Select É to deactivate the CHILD LOCK.
Notes:
Confirmation of the 4-digit code is necessary when:
– The code is entered for the very first time (see
above),
– The code is changed or cancelled (see ‘Changing
the 4-digit code’),
1en
1en
1
Access control
Child lock
Status window
Parental level
2
Change country
Change code
Authorising discs
1
Insert the disc.
➜ The ‘child safe’ dialog will appear.
2 You will be asked to enter your secret code for
‘Play Once ‘or ‘Play Always.’
● If ‘Play Once’, disc can be played untill you select
another disc, open the disc tray or turn the player
off.
● If ‘Play Always’, disc will become authorized and
can always be played, even if the Child Lock is set
to ON.
Notes:
– The player memory can maintain 80 authorized
(‘Child safe’) disc titles. A disc will be placed in the
list when ‘Play Always’ is selected.
– Each time a ‘child safe’ disc is played, it will be
placed on top of the list. When the list is full, the last
disc in the list will be replaced when a new disc is
added.
22
Deauthorising discs
1
2
Insert the disc.
➜ Playback starts automatically.
Press 9 while { is visible.
➜ The | will appear and the disc is now
deauthorized.
Note:
– Playback continues even after you have
deauthorized the disc. Press 9 if you want to stop it.
Parental Control DVD
Movies on DVDs may contain scenes not suitable
for children. Therefore, discs may contain
‘Parental Control’ information which applies to
the complete disc or to certain scenes on the disc.
These scenes are rated from 0 to 8, and
alternative, more suitable scenes are available on
the disc. Ratings are country dependent. The
‘Parental Control’ feature allows you to prevent
discs from being played by your children or to
have certain discs played with alternative scenes.
1en
1en
1
2
Access control
Status window
• [][][]
insert code
Access Control
1
2
3
4
5
When disc playback is stopped, select ACCESS
CONTROL in the Personal Preferences menu
using 3/4.
Enter your 4-digit code. If necessary, enter the
code a second time.
Move to Parental Control using 3/4.
Move to value adjustment (‘– –’ -8) using 2.
Then use 3/4 or the numerical keys on the
remote control to select a rating from 1 to 8 for
the disc inserted.
Rating 0 (displayed as ‘– –’):
Parental Control is not activated. The Disc will be
played in full.
6
Ratings 1 to 8:
The disc contains scenes not suitable for children.
If you set a rating for the player, all scenes with the
same rating or lower will be played. Higher rated
scenes will not be played unless an alternative
which has the same rating or lower is available on
the disc. If no suitable alternative is found,
playback will stop and the 4-digit code has to be
entered.
Press ENTER/OK or 1 to confirm, then press 1
again to exit the Personal Preferences menu.
Access control
Child lock
Status window
Parental level
Change country
Change code
Country
1
2
3
4
5
6
You can set the DVD player to block or allow
DVD playback according to the country rating
selected in the DVD.
When disc playback is stopped, select ACCESS
CONTROL in the Personal Preferences menu
using 3/4.
Enter the 4-digit code.
Move to CHANGE COUNTRY using 4.
Press 2.
Select a country using 3/4.
Press ENTER/OK or 1 to confirm, then press 1
again to exit the menu.
Changing the 4-digit code
1
2
3
4
5
6
When disc playback is stopped, select ACCESS
CONTROL in the Personal Preferences menu
using 3/4.
Enter the current 4 digit code.
Move to CHANGE CODE using 4 and press 2.
Enter the new 4-digit code.
Enter the code a second time and reconfirm by
pressing ENTER/OK.
Press 1 to exit the menu.
➜ The new 4 digit code will be take effect.
If you forget your 4 digit code
1
2
3
4
Press 9 to exit the ‘Child Safe’ screen.
Select ACCESS CONTROL in the Personal
Preferences menu using 3/4.
The 4-digit code can be cancelled by pressing 9
four times in the ‘Access Control’ dialog.
You can then enter a new code (twice!) as
described above in ‘Changing the 4 digit code’.
Parental Control Disclaimer
This player features the PARENTAL CONTROL
system which is to activate when playing DVD
discs furnished with certain software coding only.
Also note that at the time of release of this player,
certain aspects of the technical standards had not
been settled between set makers and the disc
industries.
On this basis, YAMAHA cannot guarantee the
functioning of the PARENTAL CONTROL
system and denies any liability associated with
unintended watching of disc content.
If in doubt, please make sure the disc plays
according to your PARENTAL CONTROL
settings before you allow children access to the
player.
23
English
Activating/Deactivating Parental
Control
Troubleshooting
WARNING
Under no circumstances should you try to repair the system yourself, as this will invalidate the
warranty. Do not open the system as there is a risk of electric shock.
If a fault occurs, first check the points listed below before taking the system for repair.
Problem
24
Solution
No power
– Check if the AC power cord is properly connected.
No picture
– Check if the TV is switched on.
– Check the video connection.
Distorted picture
– Sometimes a small amount of picture distortion may appear.
This is not a malfunction.
Completely distorted picture or
black/white picture with DVD or
Video CD
– Make sure the NTSC/PAL setting at the DVD player matches
the video signal of your television.
(See NTSC/PAL Conversion/Settings)
No sound or distorted sound
– Adjust the volume.
– Check that the speakers are connected correctly.
No audio at digital output
– Check the digital connections.
– Check the settings menu to make sure the digital output is set
to ALL or PCM.
– Check if the audio format of the selected audio language
matches your receiver capabilities.
Disc can’t be played
– Ensure the disc label is facing up.
– Check if the disc is defective by trying another disc.
Picture freezes momentarily during
playback
– Check the disc for fingerprints/scratches and clean with a soft
cloth wiping from center to edge.
No return to start-up screen when
disc is removed
– Reset the player by switching the player off, then on again.
The player does not respond to the
remote control
– Aim the remote control directly at the sensor on the front of
the player.
– Reduce the distance to the player.
– Replace the batteries in the remote control.
– Re-insert the batteries with their polarities (+/– signs) as
indicated.
Buttons do not work or player stops
responding
– To completely reset the player, unplug the AC cord from the
AC outlet for 5-10 seconds.
Player does not respond to some
operating commands during
playback
– Operations may not be permitted by the disc. Refer to the
instructions of the disc.
This player does not respond to any
command when turned on for the
first time
– Turn on your TV and follow the procedures on the screen to
decide initial setup items.
Specifications
AUDIO PERFORMANCE
DVD Video
DVD+RW
DVD+R
Video CD and SVCD
CD (CD-R and CD-RW)
MP3 CD
DA Converter
DVD
CD/Video CD
S-Video CD
TV STANDARD (PAL/50Hz) (NTSC/60Hz)
Number of lines
Playback
625
Multistandard
525
(PAL/NTSC)
VIDEO PERFORMANCE
YUV output
S-Video output
Video output
Black Level Shift
Video Shift
Y: 1Vpp into 75 ohm
Pr/Cr Pb/Cb: 0.7Vpp into 75 ohm
Y: 1Vpp into 75 ohm
C: 0.3Vpp into 75 ohm
1 Vpp into 75 ohm
On/Off
Left/Right
24 bits
fs 96 kHz
fs 44.1 kHz
fs 48 kHz
fs 44.1 kHz
Signal-Noise (1kHz)
Dynamic Range (1kHz)
Harmonic Distortion + Noise (1kHz)
MPEG MP3
CONNECTIONS
Y Pb/Cb Pr/Cr (480i/p)
S-Video Output
Video Output
Audio L+R output
Subwoofer output
Digital Output
AUDIO FORMAT
CABINET
Dolby Digital/
DTS/MPEG
PCM
Dimensions (w x h x d)
Weight
Compressed Digital
16, 20, 24 bits
fs, 44.1, 48, 96 kHz
MP3
96, 112, 128, 256 kbps and
(Joliet)
variable bit rate fs 32, 44.1, 48kHz
Full decoding of Dolby Digital and DTS multi channel sound
Analog Stereo Sound
Dolby Surround-compatible downmix from Dolby Digital
multi-channel sound
3D Sound for virtual 5.1 channel sound on 2 speakers
2 Hz - 44 kHz
2 Hz - 20 kHz
2 Hz - 22 kHz
2 Hz - 20 kHz
105 dB
100 dB
0.003%
MPEG Audio L3
Cinch 3x (green, blue, red)
Mini DIN, 4 pins
Cinch (yellow)
Cinch (white/red) x2
Cinch (black)
1 coaxial, 1 optical
IEC958 for CDDA / LPCM
IEC1937 for MPEG1/2, Dolby
Digital, DTS
435 x 116 x 425 mm
Approx. 6 Kg
POWER SUPPLY
Power inlet
U.S.A. model
Australia model
Power usage
Power usage standby
120V, 60Hz
240V, 50Hz
Approx. 20W
< 5W
* typical playing time for movie with 2 spoken languages and
3 subtitle languages
Specifications subject to change without prior notice.
25
English
PLAYBACK SYSTEM
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
YAMAHA CORPORATION
3139 246 12101
Printed in China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement