Yamaha | PDM-1 | Operating instructions | Yamaha PDM-1 Operating Instructions

U
PDM-1
INPUT
INPUT
SURROUND
VOL
VOL
N
R
PICTURE
PICTURE
PICTURE
POS. /SIZE
SOUND
SOUND
HIGH DEFINITION
PLASMA MONITOR
SET
SET UP
UP
ASPECT
ASPECT
OFF TIMER
PC
PC
+
–
VOL
INPUT
POWE
R
/
Y
R - STANDB ON
G POWER
Operating Instructions
English
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: To reduce the risk of electric shock, do not remove cover or back.
No user-serviceable parts inside. Refer servicing to qualified service personnel.
The lightning flash with
arrow-head within a triangle
is intended to tell the user
that parts inside the product
are a risk of electric shock to
persons.
The exclamation point within
a triangle is intended to tell
the user that important
operating and servicing
instructions are in the papers
with the appliance.
WARNING: To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain
or moisture.
Do not place containers with water (flower vase, cups, cosmetics, etc.) above the set. (including
on shelves above, etc.)
WARNING: 1) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to
qualified service personnel.
2) Do not remove the grounding pin on the power plug. This apparatus is equipped with a three pin
grounding-type power plug. This plug will only fit a grounding-type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet, contact an electrician.
Do not defeat the purpose of the grounding plug.
2
Important Safety Instructions
1) Read these instructions.
All the safety and operating instructions should be read before the appliance is operated.
2) Keep these instructions.
The safety and operating instructions should be retained for future reference.
3) Heed all warnings.
All warnings on the appliance and in the operating instructions should be adhered to.
4) Follow all instructions.
All operating and use instructions should be followed.
5) Do not use this apparatus near water.
For example, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and
the like.
6) Clean only with dry cloth.
Do not use liquid cleaners or aerosol cleaners. Use a dry cloth for cleaning.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Slots and Openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to
protect it from overheating. The openings should never be blocked by placing the product on a bed, sofa, rug, or other
similar surface.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)
that produce heat.
This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is
provided or the manufacturer’s instructions have been adhered to.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider
than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11) Only use attachments / accessories specified by the Manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart / apparatus combination to avoid
injury from tip-over.
Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination
to overturn.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
This will prevent damage to the product due to lightning and power-line surges.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15) To prevent electric shock, ensure the grounding pin on the AC cord power plug is securely connected.
3
Table of Contents
Important Safety Instructions ...................................... 3
COMPLIANCE INFORMATION STATEMENT ............... 5
Safety Precautions ........................................................ 6
Accessories ................................................................... 8
Accessories Supplied ................................................... 8
Optional Accessories ................................................... 8
Remote Control Batteries ............................................. 9
Basic Controls ............................................................. 10
Connections ................................................................ 11
Basic connection ........................................................ 12
COMPONENT/RGB Input connection ....................... 13
Speaker Terminals connection ................................... 14
PC Input Terminals connection .................................. 15
SERIAL Terminals connection .................................... 17
Power ON/OFF and Input Signal Selection ............... 18
AC cord connection .................................................... 18
Power ON/OFF .......................................................... 18
Select the Input Signal ............................................... 19
Selecting the ON-Screen Menu Language ................ 19
On-Screen Menu Display from Remote Control ....... 20
ASPECT Controls ........................................................ 22
ADJUSTING PICTURE POSITION/SIZE ..................... 24
SOUND ADJUSTMENT ................................................ 26
MUTE ......................................................................... 26
SURROUND Controls ................................................. 27
PICTURE Adjustments ................................................ 28
ADVANCED SETTINGS ............................................ 29
SET UP TIMER ............................................................. 30
PRESENT TIME OF DAY Set .................................... 30
TIMER Set ................................................................. 31
SCREENSAVER (For preventing after-images) ........ 32
Setup of SCREENSAVER Time ................................. 33
SIDE BAR ADJUST ................................................... 33
SET UP for Input Signals ............................................ 34
COMPONENT/RGB/ IN SELECT .............................. 34
3D Y/C FILTER – For NTSC Video images ............... 34
COLOR SYSTEM / AUTO .......................................... 35
3:2 PULLDOWN ......................................................... 35
SYNC ......................................................................... 36
H-FREQ. (kHz)/V-FREQ. (Hz) ................................... 36
Troubleshooting .......................................................... 37
Specifications .............................................................. 38
Note:
Do not allow a still picture to be displayed for an extended period, as this can cause a permanent afterimage to remain on the plasma display.
Examples of still pictures include logos, video games, computer images, teletext and images displayed in
4:3 mode.
Trademark Credits
VGA is a trademark of International Business Machines Corporation.
Macintosh is a registered trademark of Apple Computer, USA.
S-VGA is a registered trademark of the Video Electronics Standard Association.
Even if no special notation has been made of company or product trademarks, these trademarks have been fully
respected.
•
•
•
4
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party: Yamaha Electronics Corporation
Address: 6660 Orangethorpe Avenue
Buena Park, CA90620
Telephone: 714-522-9105
Fax: 714-670-0108
Type of Equipment: High Definition Plasma Monitor
Moel Name: PDM-1
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received, including interference that may cause undesired operation.
See the user manual instructions if interference to radio reception is suspected.
FCC INFORMATION (for US customers only)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements.
Modifications not expressly approved by Yamaha may void
your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories
and/or another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used.
Follow all installation instructions. Failure to follow
instructions could void your FCC authorization to use this
product in the USA.
3. NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15 for
Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your
use of this product in a residential environment will not result
in harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in the
users manual, may cause interference harmful to the operation
of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product is
found to be the source of interference, which can be determined
by turning the unit “OFF” and “ON”, please try to eliminate the
problem by using one of the following measures:
Relocate either this product or the device that is being affected
by the interference.
Utilize power outlets that are on different branch (circuit breaker
or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead, change
the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory results,
please contact the local retailer authorized to distribute this
type of product. If you can not locate the appropriate retailer,
please contact Yamaha Electronics Corp., U.S.A. 6660
Orangethorpe Ave, Buena Park, CA 90620.
The above statements apply ONLY to those products distributed
by Yamaha Corporation of America or its subsidiaries.
CANADIAN NOTICE:
This Class B digital apparatus complies with Canadian ICES-003.
5
Safety Precautions
WARNING
Set up
Do not place the plasma display on sloped or unstable surfaces.
The plasma display may fall off or tip over.
•
Do not place any objects on top of the plasma display.
If water spills onto the plasma display or foreign objects get inside it, a short-circuit may occur which could result in fire
or electric shock. If any foreign objects get inside the plasma display, please consult an Authorized Service Center.
•
Do not cover the ventilation holes.
Doing so may cause the plasma display to overheat, which can cause fire or damage to the plasma display.
•
If using the pedestal (optional accessory), leave a space of 3 15/16” (10 cm) or more at the top, left and right, 2 3/8” (6
cm) or more at the bottom, and 2 3/4” (7 cm) or more at the rear. If using some other setting-up method, leave a
space of 3 15/16” (10 cm) or more at the top, bottom, left and right, and 3/4” (1.9 cm) or more at the rear.
Avoid installing this product near electronic equipment that easily receives electromagnetic waves.
It may cause interference in image, sound, etc. In particular, keep video equipment away from this product.
•
AC Power Supply Cord
The plasma display is designed to operate on 120 V AC, 50/60 Hz.
Securely insert the power cord plug as far as it will go.
If the plug is not fully inserted, heat may be generated which could cause fire. If the plug is damaged or the wall socket
plate is loose, they should not be used.
•
Do not handle the power cord plug with wet hands.
Doing so may cause electric shocks.
•
Do not do anything that might damage the power cable. When disconnecting the power cable, hold the plug, not
the cable.
Do not make any modifications, place heavy objects on, place near hot objects, heat, bend, twist or forcefully pull the
power cable. Doing so may cause damage to the power cable which can cause fire or electric shock. If damage to the
cable is suspected, have it repaired at an Authorized Service Center.
•
If the plasma display will not be used for a long period of time, unplug the power cord from the wall outlet.
If problems occur during use
If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odor is detected from the plasma
display, unplug the power cord immediately.
Continuous use of the Display under these conditions might cause fire or permanent damage to the unit. Have the
Display evaluated at an Authorized Service Center. Services to the Display by any unauthorized personnel are strongly
discouraged due to its high voltage dangerous nature.
•
If water or foreign objects get inside the plasma display, if the plasma display is dropped, or if the cabinet becomes
damaged, disconnect the power cord plug immediately.
A short may occur, which could cause fire. Contact an Authorized Service Center for any repairs that need to be made.
•
6
Safety Precautions
CAUTION
This plasma display is for use only with the following optional accessories. Use with any other type of optional
accessories may cause instability which could result in the possibility of injury.
NS-F100, NS-F80, NS-F70
• Speakers (main speaker) ................
(center speaker) .............. NS-CF100
PDS-150
• Pedestal ..........................................
..........................
Wall
Mounting
Unit
PWK-150
•
Always be sure to ask a qualified technician to carry out set-up.
When using the plasma display
Do not bring your hands, face or objects close to the ventilation holes of the plasma display.
Top of the plasma display is usually very hot due to the high temperature of exhaust air being released through the
ventilation holes. Burns or personal injuries can happen if any body parts are brought too close. Placing any object
near the top of the display could also result in heat damages to the object as well as to the Display if its ventilation
holes are blocked.
•
Be sure to disconnect all cables before moving the plasma display.
Moving the Display with its cables attached might damage the cables which, in turn, can cause fire or electric shock.
•
Disconnect the power plug from the wall outlet as a safety precaution before carrying out any cleaning.
Electric shocks can result if this is not done.
•
Clean the power cable regularly to prevent it from becoming dusty.
Built-up dust on the power cord plug can increase humidity which might damage the insulation and cause fire. Unplug
the cord from the wall outlet and clean it with a dry cloth.
•
Cleaning and maintenance
The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning
cloth or a soft, lint-free cloth.
If the surface is particularly dirty, soak a soft, lint-free cloth in a weak detergent solution and then wring the cloth to
remove excess liquid. Use this cloth to wipe the surface of the display panel, then wipe it evenly with a dry cloth, of the
same type, until the surface is dry.
Do not scratch or hit the surface of the panel with fingernails or other hard objects. Furthermore, avoid contact with
volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the surface may be adversely
affected.
•
•
If the cabinet becomes dirty, wipe it with a soft, dry cloth.
If the cabinet is particularly dirty, soak the cloth in a weak detergent solution and then wring the cloth dry. Use this cloth
to wipe the cabinet, and then wipe it dry with a dry cloth.
Do not allow any detergent to come into direct contact with the surface of the plasma display.
If water droplets get inside the unit, operating problems may result.
Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the cabinet
surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact
with articles made from rubber or PVC.
•
•
•
Note:
Do not allow a still picture to be displayed for an extended period, as this can cause a permanent after-image to remain
on the plasma display.
Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode.
7
Accessories
Accessories Supplied
Check that you have the Accessories and items shown
Remote Control Transmitter
EUR646525
Batteries for the Remote
Control Transmitter
(AA(R6) Battery × 2)
AC cord
INPUT
SURROUND
VOL
N
PICTURE
R
SOUND
PICTURE
POS. /SIZE
PC
SET UP
ASPECT
OFF TIMER
Ferrite core
(small size) × 1
Ferrite core
(large size) × 2
Fixing bands × 2
Speaker Wire × 2
Optional Accessories
• Speakers
(main speaker)
NS-F100
(center speaker)
NS-CF100
• Pedestal
PDS-150
• Wall Mounting Unit
PWK-150
NS-F80 (for shelf-placing)
NS-F70 (for wall-hanging)
For assembling
Full instructions are supplied with each of the optional accessories for use with this plasma display.
8
Remote Control Batteries
Requires two AA batteries.
1. Turn the transmitter face down.
Press and slide off the battery
cover.
2. Install the batteries as shown in the
battery compartment. (Polarity + or
– must match the markings in the
compartment.)
3. Replace the cover and slide in
reverse until the lock snaps.
Two "AA" size
Helpful Hint:
For frequent remote control users, replace old batteries with Alkaline
batteries for longer life.
Precaution on battery use
Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter.
Observe the following precautions:
1. Batteries should always be replaced as a pair. Always use new batteries when replacing the old set.
2. Do not combine a used battery with a new one.
3. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).
4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.
5. Battery replacement is necessary when the remote control acts sporadically or stops operating the plasma display.
9
Basic Controls
Main POWER ON/OFF Switch
Power Indicator
The Power Indicator will light.
POWER-OFF Indicator not illuminated
(The unit will still consume some power
as long as the power cord is inserted into
the wall outlet.)
STAND-BY .....Red
POWER-ON.....Green
•
•
•
—
INPUT
R - STANDBY
G POWER ON
VOLUME Adjustment
Push the Volume Up “+” or
Down “–” button to increase
or decrease the sound
volume level.
SURROUND button
(see page 27)
INPUT button
(VIDEO (S VIDEO), COMPONENT/
RGB and PC Mode Selection)
Press to select VIDEO (S VIDEO),
COMPONENT/RGB and PC input
signal modes sequentially. (see page 19)
STATUS button
Push the “STATUS” button to display
the current system status.
VIDEO
+
INPUT button
(VIDEO (S VIDEO), COMPONENT/RGB
and PC Mode Selection)
Push the “INPUT” button to select VIDEO
(S VIDEO), COMPONENT/RGB and PC
input signal modes sequentially.
(see page 19)
STAND-BY (ON/OFF) button
The plasma display must first be plugged into the wall
outlet and turned on at the power switch (see page 18).
Push this button to turn the plasma display ON, from STANDBY mode. Push it again to turn the plasma display OFF to
STAND-BY mode.
NORMAL
VOL
1
INPUT
INPUT
2
Sound mute On/Off (see page 26)
SURROUND
OFF TIMER
90
3
VOL
VOL
1 VIDEO (S VIDEO), COMPONENT/
RGB, PC mode
2 ASPECT mode (see page 22)
3 OFF TIMER
The OFF TIMER indicator is displayed
only when the off timer has been set.
N button
(see page 25, 26, 28, 29)
N
R
VOLUME Adjustment
Press the Volume Up “+” or Down
“–” button to increase or decrease
the sound volume level.
R button (see page 21)
ACTION button
Press to make selections
PICTURE
PICTURE
SOUND
SOUND
SET
SET UP
UP
PICTURE button
(see page 28)
POSITION buttons
SET UP button (see page 20)
PICTURE
POS. /SIZE
SOUND button (see page 26)
ASPECT
ASPECT
PICTURE POS./SIZE button
(see page 24)
PC
OFF TIMER
ASPECT button
Press to adjust the aspect.
(see page 22)
PC
PC button
Push the “PC” mode selection
button to select the PC mode.
This button is used to switch
OFF TIMER button
directly to PC mode.
The plasma display may be preset to switch to stand-by after a fixed period. The
setting changes to 30 minutes, 60 minutes, 90 minutes and 0 minutes (off timer
cancelled) each time the button is pressed.
30
60
90
When three minutes remain, “Off timer 3” will flash.
0
The off timer is cancelled if a power interruption occurs.
10
Connections
SPEAKER
Terminals (R)
SPEAKER
Terminals (L)
– Cable fixing bands
Secure any excess cables with bands, as required.
Pass the attached cable fixing
band through the clip as
shown in the figure.
To secure cables connected to
Terminals, wrap the cable fixing band
around them then pass the pointed end
through the locking block, as shown in
the figure.
1
2
To tighten:
To loosen:
Push
the catch
Pull
Pull
AUDIO
R
R
L
AUDIO
VIDEO
AV IN
AV IN Terminals
(see page 12, 15)
S VIDEO
L
AUDIO
VD
HD
PR/CR/R
PB/CB/B
COMPONENT/RGB IN
COMPONENT/RGB IN and Audio IN
Terminals (see page 13, 15)
Y/G
PC
From EXIT monitor Terminal
on Computer (see page 15)
IN
SERIAL
From SERIAL Terminal on
Computer (see page 17)
11
Connections
Basic connection
(Example) When connecting an AV amplifer
S VIDEO 4 pin socket
R
R
L
AUDIO
VIDEO
Luminance earth
Chrominance earth
Luminance in
Chrominance in
L
S VIDEO
AUDIO
HD
VD
AV IN
PR/CR/R
PB/CB/B
Y/G
COMPONENT/RGB IN
Video cable
S Video cable
Component
Video cable
AV amplifer
VOLUME
INPUT SELECTOR
VIDEO
S VIDEO
INPUT MODE
STANDBY
/ON
SPEAKERS
A
B
6CH
INPUT
PROGRAM
STEREO FM/AM
PRESET
/TUNING
A/B/C/D/E
PRESET
/TUNING
EDIT
EFFECT
TREBLE
BASS
BALANCE
MEMORY
SAT
MD/TAPE
CD–R
VCR 1
1
ON
VCR 2
OFF
COMPONENT
VIDEO
TUNING
MODE
MAN'L/AUTO FM AUTO/MAN'L MONO
SOURCE/REMOTE
D–TV/LD
DVD
CABLE
PROCESSOR BASS
DIRECT EXTENSION
TUNER
CD
PHONO
L
R
VIDEO AUX
SILENT
VCR 3/DVR
MONITOR
OUT
VIDEO AUX
PHONES
S VIDEO
VIDEO
L
REC OUT/ZONE 2
AUDIO R
MONITOR
OUT
OPTICAL
2
Subwoofer
Center speaker
(NS-CF100)
Front effect
speaker
Rear
speaker
Main
speaker
(NS-F100)
Main
speaker
(NS-F100)
Rear
speaker
Front effect
speaker
Notes:
(1) Change the “COMPONENT/RGB-IN” setting in the “SET UP” menu to “COMPONENT”. (see page 34)
(2) Any equipment and cables other than the display illustrated above are not included.
(3) Choose one connecting cable from Video, S Video or Component Video, that is suitable for the equipment being used.
(4) The quality of images obtained varies between connection methods in the descending order of Component Video,
S Video and Video.
12
Connections
COMPONENT/RGB Input connection
RGB signal (R, G, B, HD, VD) connection
RGB input to
R, G, B, HD, VD sockets
BNC-RCA
adaptor plug
Example of input signal source
HDTV-compatible VCR
5×BNC
RGB cables
RGB camera
R
L
AUDIO
VD
HD
PR/CR/R
PB/CB/B
Y/G
COMPONENT/RGB IN
AUDIO
2×RCA audio cables
Audio input to
L/R sockets
Computer
VD
HD
R
B
G
Notes:
(1) Change the “COMPONENT/RGB-IN” setting in the “SET UP” menu to “COMPONENT”. (see page 34)
(2) Any equipment and cables other than the display illustrated above are not included.
(3) Choose one connecting cable from Video, S Video or Component Video, that is suitable for the equipment being used.
(4) The quality of images obtained varies between connection methods in the descending order of Component Video,
S Video and Video.
13
Connections
Speaker Terminals connection
When you do not use an AV amplifer, connect the speakers directly with the speaker terminals of the plasma display.
Refer to the speaker’s Installation Manual for details on speaker installation.
Make sure to use the supplied ferrite core speaker cables to connect
the speakers. Other types of speaker wires are not suitable.
1
3
2
1
Remove the tubes
from the ends of
the speaker cables.
R
R
L
AUDIO
VIDEO
S VIDEO
2
L
AUDIO
VD
AV IN
HD
PR/CR/R
PB/CB/B
Y/G
COMPONENT/RGB IN
Audio cable
Audio cable
Component
Video cable
Video cable
S Video
cable
Audio
cable
R
Audio
OUT L
Video
OUT
(DVD Player)
R
Audio
OUT L
S Video
OUT
(DVD Player)
R
Audio
OUT
L
Component Video OUT
Y
PB
PR
(DVD Player)
VIDEO signal connection
Component signals (Y, PB, PR) connection
S VIDEO signal connection
Notes:
(1) Change the “COMPONENT/RGB-IN” setting in the “SET UP” menu to “COMPONENT”. (see page 34)
(2) Any equipment and cables other than the display illustrated above are not included.
(3) Choose one connecting cable from Video, S Video or Component Video, that is suitable for the equipment being used.
(4) The quality of images obtained varies between connection methods in the descending order of Component Video,
S Video and Video.
14
Connections
PC Input Terminals connection
COMPUTER
AUDIO
PC IN
POWER
/
R - STANDBY
INPUT
–
VOL
+
G POWER ON
Conversion adapter
(if necessary)
Less than
3" 15/16
(10 cm)
Ferrite core (large size)
(supplied)
D-sub 15p
RGB
PC cable
Less than
3" 15/16
(10 cm)
Ferrite core (small size)
(supplied)
Audio
1/8" (3mm) stereo plug
Connect a cable that matches
the audio output terminal on the computer.
Installing the ferrite core (Small size)
1
2
3
Open
Press the cable
through and close
Pull back the tabs
(in two places)
Installing the ferrite core (Large size)
1
2
3
Open
Pull back the tabs
(in two places)
Press the cable
through and close
Notes:
(1) Computer signals which can be input are those with a horizontal scanning frequency of 15.6 to 110 kHz and vertical
scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200
lines.)
(2) The display resolution is a maximum of 1,024 × 768 dots when the aspect mode is set to “NORMAL”, and 1,366 × 768
dots when the aspect mode is set to “FULL”. If the display resolution exceeds these maximums, it may not be possible
to show fine detail with sufficient clarity.
(3) The PC input terminals are DDC1/2B-compatible. If the computer being connected is not DDC1/2B-compatible, you will
need to make setting changes to the computer at the time of connection.
(4) Some PC models cannot be connected to the set.
(5) There is no need to use an adapter for computers with DOS/V compatible D-sub 15P terminal.
(6) The computer shown in the illustration is for example purposes only.
(7) Additional equipment and cables shown are not supplied with this set.
(8) Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified
frequency range.
15
Connections
Signal Names for D-sub 15P Connector
11 12 13 14 15
6
7
1
9 10
8
2
3
4
5
Pin layout for PC input
terminal
Pin No.
1
2
3
4
5
Signal Name
R
G
B
GND (Ground)
GND (Ground)
Pin No.
Signal Name
Pin No.
6
GND (Ground)
11
7
GND (Ground)
12
8
GND (Ground)
13
9
NC (not connected)
14
10
GND (Ground)
15
AV (VIDEO, S VIDEO) input
signal name
1
2
3
4
5
NTSC
PAL
PAL60
SECAM
Modified NTSC
horizontal
frequency(kHz)
15.734
15.625
15.734
15.625
15.734
vertical
frequency(Hz)
59.95
50
59.95
50
59.95
horizontal
frequency(kHz)
15.734
15.625
31.468
31.25
45
33.75
28.125
27
27
vertical
frequency(Hz)
59.94
50
59.94
50
60
60
50
24
48
horizontal
frequency(kHz)
31.5
31.5
35
37.5
31.7
37.9
46.9
53.7
49.7
48.4
56.5
60
68.7
68.7
64
80
91.1
75
vertical
frequency(Hz)
70
59.94
67
75
60
60
75
85
75
60
70
75
85
75
60
75
85
60
COMPONENT/RGB input
signal name
1
2
3
4
5
6
7
8
9
525 (480) /60i
625 (575) /50i
525 (480) /60p
625 (575) /50p
750 (720) /60p
1,125 (1,080) /60i
1,125 (1,080) /50i
1,125 (1,080) /24p
1,125 (1,080) /24sF
PC input
signal name
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
16
640 × 400 @70
640 × 400 @60
Macintosh13” (640 × 480)
640 × 480 @75
852 × 480 @60
800 × 600 @60
800 × 600 @75
800 × 600 @85
Macintosh16” (832 × 624)
1,024 × 768 @60
1,024 × 768 @70
1,024 × 768 @75
1,024 × 768 @85
Macintosh21” (1,152 × 870)
1,280 × 1,024 @60
1,280 × 1,024 @75
1,280 × 1,024 @85
1,600 × 1,200 @60
Signal Name
GND (Ground)
SDA
HD/SYNC
VD
SCL
Connections
SERIAL Terminals connection
The SERIAL terminal is used when the plasma display is controlled by a computer.
COMPUTER
6
1
RS-232C
straight cable
Ferrite core
(large size)
(supplied)
SERIAL
7
2
8
3
9
4
5
Pin layout for RS-232C
Installing the ferrite core
(Large size)
Open
Less than
3" 15/16
(10 cm)
D-sub 9p
Notes:
(1) Use the RS-232C cable to connect the computer to the plasma display.
(2) The computer shown is for example purposes only.
(3) Additional equipment and cables shown are not supplied with this set.
The SERIAL terminal conforms to the RS-232C interface specification, so that the plasma display can be controlled by a
computer which is connected to this terminal.
The computer will require software which allows the sending and receiving of control data which satisfies the conditions
given below. Use a computer application such as programming language software. Refer to the documentation for the
computer application for details.
Communication parameters
Signal level
Synchronization method
Baud rate
Parity
Character length
Stop bit
Flow control
RS-232C Conversion cable
Details
D-sub 9-pin female
RXD
2
3
TXD
5
GND
Non use
4 • 6
RS-232C compliant
Asynchronous
9600 bps
None
8 bits
1 bit
–
Basic format for control data
The transmission of control data from the computer starts
with a STX signal, followed by the command, the
parameters, and lastly an ETX signal in that order. If there
are no parameters, then the parameter signal does not need
to be sent.
7
8
1 • 9
C1 C2 C3
Start
(02h)
:
P1 P2 P3 P4 P5
ETX
Colon
Parameter(s)
(1 - 5 bytes)
3-character
command (3bytes)
End
(03h)
NC
Command
Command
PON
POF
AVL
AMT
STX
Shorted
IIS
DAM
Parameter
None
None
**
0
1
None
VID
YP1
RG1
None
NORM
ZOOM
FULL
JUST
SELF
Control details
Power ON
Power OFF
Volume 00 ~ 63
Audio MUTE OFF
Audio MUTE ON
Input select (toggle)
VIDEO Mode
COMPONENT / RGB mode (processed as
a Y/PB/PR or RGB signals as set by this unit)
PC mode
Screen mode select (toggle)
NORMAL (4:3)
ZOOM
FULL
JUST
AUTO
Notes:
(1) If multiple commands are transmitted, be sure to wait
for the response for the first command to come from
this unit before sending the next command.
(2) If an incorrect command is sent by mistake, this unit will
send an “ER401” command back to the computer.
With the power off, this display responds to PON command only.
17
Power ON/OFF and Input Signal Selection
AC cord connection
Connecting the AC cord plug to the plasma display.
Power ON/OFF
Connecting the plug to the Wall Outlet
R - STANDBY
INPUT
—
VOL
Push the
switch on the plasma display to turn the set
on POWER-ON.
Power Indicator: Green
+
G POWER ON
R - STANDBY
G POWER ON
Remote Control Sensor
Power Indicator
When the POWER is turned on for the first
time, the LANGUAGE selection screen is
displayed.
From the second time on, language
selection can be done from the setup
menu. (see page 19)
Select the desired language using the
and keys and press the ACTION
button.
INPUT
VOL
18
From the second time on, the screen shown below
is displayed for a while (setting condition is an
example).
OSD LANGUAGE
English (UK)
Deutsch
Fran ais
Italiano
Espa ol
ENGLISH (US)
SELECT
VIDEO
NORMAL
SET
Press the
button on the remote control to turn the
plasma display off.
Power Indicator: Red (STAND-BY)
Press the
button on the remote control to turn the
plasma display on.
Power Indicator: Green
SURROUND
N
Example: The screen below is displayed for a while after the
plasma display is turned on. (setting condition is
an example.)
R
To turn the power for the plasma display off, press the switch
on the plasma display, when the plasma display is on or in
standby mode.
Power ON/OFF and Input Signal Selection
Select the Input Signal
INPUT
Press the INPUT button to select the input
video signal desired from equipment such as
a VCR which has been connected to the
plasma display.
Input signals will change as follows:
For COMPONENT INPUT (see page 32)
VIDEO
R - STANDBY
INPUT
—
VOL
COMPONENT
PC
+
G POWER ON
For RGB INPUT (see page 32)
INPUT
—
+
VOL
VIDEO
RGB
PC
INPUT
SURROUND
VOL
N
R
Selecting the On-Screen Menu Language
SET UP
press to display the SET UP menu.
press to select the OSD LANGUAGE.
INPUT
SURROUND
press to select your preferred language.
VOL
N
SET UP
R
COMPONENT/RGB-IN SELECT
selectable languages
PICTURE
SOUND
SET UP
ENGLISH(UK)
Deutsch
Français
Italiano
Español
ENGLISH(US)
.......(Chinese)
RGB
SIGNAL
SCREENSAVER
ENGLISH (US)
OSD LANGUAGE
SET UP TIMER
19
On-Screen Menu Display from Remote Control
To PICTURE adjust menu
(see page 28)
Press to select each item.
PICTURE
NORMALIZE NORMAL
PICTURE MENU
PICTURE
BRIGHTNESS
COLOR
TINT
SHARPNESS
COLOR TEMP
ADVANCED SETTINGS
STANDARD
0
0
0
0
0
NORMAL
ON
SET UP
COMPONENT/RGB-IN SELECT
To ADVANCED SETTINGS
(see page 28, 29)
INPUT
ADVANCED SETTINGS
NORMALIZE NORMAL
BLACK EXTENSION
W/B HIGH R
W/B HIGH B
W/B LOW R
W/B LOW B
GAMMA
SURROUND
0
0
0
0
0
RGB
SIGNAL
SCREENSAVER
ENGLISH (US)
OSD LANGUAGE
SET UP TIMER
VOL
N
R
2. 2
To SOUND adjust menu
(see page 26)
PICTURE
SOUND
NORMALIZE
AUDIO MENU
BASS
TREBLE
BALANCE
SURROUND
SOUND
SET UP
SET UP
COMPONENT/RGB-IN SELECT
NORMAL
STANDARD
0
0
0
ON
PICTURE
POS. /SIZE
ASPECT
RGB
SIGNAL
SCREENSAVER
ENGLISH (US)
OSD LANGUAGE
SET UP TIMER
OFF TIMER
PC
To PICTURE POS./SIZE adjust
menu (see page 24)
During “VIDEO (S VIDEO)” and
“COMPONENT” input signal modes.
PICTURE POS./SIZE
NORMALIZE
H-POS
H-SIZE
V-POS
V-SIZE
NORMAL
SET UP
During “RGB” and “PC” input
signal modes.
PICTURE POS./SIZE
NORMALIZE NORMAL
H-POS
H-SIZE
V-POS
V-SIZE
CLOCK PHASE
20
COMPONENT/RGB-IN SELECT
RGB
SIGNAL
SCREENSAVER
ENGLISH (US)
OSD LANGUAGE
SET UP TIMER
On-Screen Menu Display from Remote Control
Press to access each adjust
screen.
R
Press the R button to return
to “SET UP” menu.
To SIGNAL screen for
VIDEO (see page 34, 35)
[ VIDEO ]
SIGNAL
3D Y/C FILTER (NTSC)
COLOR SYSTEM
3:2 PULLDOWN
AUTO (4:3 )
ON
AUTO
OFF
NORMAL
To SIGNAL screen for
COMPONENT (see page 35)
SIGNAL
3:2 PULLDOWN
To SIGNAL screen for
RGB (see page 36)
[ COMPONENT ]
[ RGB ]
SIGNAL
OFF
H&V
SYNC
H-FREQ.
V-FREQ.
31.5 kHz
60.0 Hz
To SIGNAL screen for PC
(see page 36)
[ PC ]
SIGNAL
H&V
SYNC
H-FREQ.
V-FREQ.
31.5 kHz
60.0 Hz
Note:
“SIGNAL” setup menu displays a different setting condition for each input signal. (see page 19)
START TIME
To setup SCREENSAVER
(See page 32)
Press to select each TIME
adjust screen.
WHITE BAR SCROLL
OFF
0:00
0:00
HIGH
0:00
00
00
FINISH TIME
SCREENSAVER
FUNCTION
MODE
SHOW DURATION
SAVER DURATION
SIDE BAR ADJUST
START TIME
HOURS ADJUSTMENT
MINUTES ADJUSTMENT
Press to display each
adjust screen.
FINISH TIME
HOURS ADJUSTMENT
MINUTES ADJUSTMENT
0:00
00
00
PERIODIC TIME
R
SHOW DURATION
HOURS ADJUSTMENT
MINUTES ADJUSTMENT
0:00
00
00
OPERATING TIME
Press the R button to return
to “SCREENSAVER” menu.
To SET UP TIMER selection
screen.(see page 30)
SET UP TIMER
PRESENT TIME
POWER ON FUNCTION
POWER ON TIME
POWER OFF FUNCTION
POWER OFF TIME
0:52
OFF
0:00
OFF
0:00
Press to select each
TIMER adjustment items.
When select TIMER
adjustment item, press
this button to SET UP
TIMER screen.
SAVER DURATION
HOURS ADJUSTMENT
MINUTES ADJUSTMENT
0:00
00
00
PRESENT TIME SETUP
PRESENT TIME OF DAY
HOURS ADJUSTMENT
MINUTES ADJUSTMENT
99 : 99
00
00
POWER ON SETUP
POWER ON TIME
HOUR ADJUSTMENT
MINUTES ADJUSTMENT
0 : 00
00
00
R
POWR OFF SETUP
Press the R button to return
to “SET UP” menu.
POWER OFF TIME
HOURS ADJUSTMENT
MINUTES ADJUSTMENT
0 : 00
00
00
21
ASPECT Controls
The plasma display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema format
picture.
ASPECT
INPUT
VOL
R
PICTURE
PICTURE
POS. /SIZE
SOUND
SET UP
ASPECT
OFF TIMER
PC
22
NORMAL
AUTO
SURROUND
N
ASPECT button
The aspect mode changes each time the ASPECT button
is pressed.
ZOOM
FULL
JUST
Notes:
(1) During RGB and PC input signal modes, the mode switches between
“NORMAL”, “ZOOM” and “FULL” only.
(2) For a 1,125i (1,080i), 750p (720p) signal input during “COMPONENT”
input signal mode, the mode is set to “FULL” mode, and switching
is not possible.
For a 525i (480i), 625i (575i), 525p (480p) and 625p (575p) signal
input during “COMPONENT” input signal mode, “AUTO” cannot be
selected.
(3) The aspect mode is memorized separately for each input terminal
(VIDEO (S VIDEO), COMPONENT, RGB and PC).
ASPECT Controls
Picture
Mode
Explanation
NORMAL will display a 4:3 picture at its standard 4:3
size.
4
NORMAL
NORMAL
3
4
ZOOM mode magnifies the central section of the picture.
16
ZOOM
ZOOM
3
4
9
FULL will display the picture at its maximum size but
with sight elongation.
16
FULL
FULL
3
4
9
16
JUST
JUST
3
4
9
16
AUTO
3
AUTO
For an elongated image
9
Image is expanded
4
3
For a 4:3 image
Changes in accordance
with the AUTO mode
setting (see page 35)
JUST mode will display a 4:3 picture at its maximum
size but with aspect correction applied to the center of
the screen so that elongation is only apparent at the
left and right edges of the screen. The size of the picture
will depend on the original signal.
The display will automatically become enlarged
(depending on the picture source), allowing you to view
the picture at its maximum size.
Note:
AUTO mode is designed to automatically adjust the
aspect ratio to handle a mix of 16:9 and 4:3 program
material. Certain 4:3 program material, such as stock
market data screens, may occasionally cause the image
size to change unexpectedly. When viewing such
programs, it is recommended that the ASPECT be set
to NORMAL.
Notes:
(1) Do not allow the picture to be displayed in 4:3 mode for an extended period, as this can cause a parmanent after-image
to remain on the plasma display panel.
(2) The S VIDEO terminal on this set can detect specially encoded signals that are compatible with a wide screen monitor.
When a full image from the S VIDEO terminal of specially encoded video is detected by the set, the screen size is
automatically set to FULL mode.
23
Adjusting PICTURE POSITION/SIZE
Adjusting screen
1
PICTURE
POS. /SIZE
Press to display the PICTURE POS./
SIZE menu.
INPUT
SURROUND
2
Press to select H-POS/H-SIZE/V-POS/
V-SIZE/CLOCK PHASE.
VOL
R
N
PICTURE
During “RGB” and “PC” input
During “VIDEO (S VIDEO)” and
“COMPONENT” input signal modes. signal modes.
PICTURE POS./SIZE
PICTURE POS./SIZE
NORMALIZE
H-POS
H-SIZE
V-POS
V-SIZE
NORMALIZE NORMAL
H-POS
H-SIZE
V-POS
V-SIZE
CLOCK PHASE
NORMAL
3
PICTURE
POS. /SIZE
SOUND
SET UP
ASPECT
OFF TIMER
PC
Press to adjust POS./SIZE.
R
Press to exit from adjust mode.
Notes:
(1) Adjustment details are memorized separately for different input signal formats (Adjustments for component signals are
memorized for 525i (480i), 625i (575i), 525p (480p), 1,125i (1,080i) and 625p (575p), 750p (720p) each, and RGB/PC
signals are memorized for each frequency.)
(2) If a “Cue” or “Rew” signal from a VCR or DVD player is received, the picture position will shift up or down. This picture
position movement cannot be controlled by the PICTURE POS./SIZE function.
24
Adjusting PICTURE POS./SIZE
When the Position Left “ ” button is pressed
When the Position Right “ ” button is pressed
When the Position Left “ ” button is pressed
When the Position Right “ ” button is pressed
When the Position Left “ ” button is pressed
When the Position Right “ ” button is pressed
When the Position Left “ ” button is pressed
When the Position Right “ ” button is pressed
H-POS
H-SIZE
V-POS
V-SIZE
CLOCK PHASE
Flickering and distortion can be eliminated by using the Position Left “ ” or Right “ ” button to
(RGB/PC in Mode) carry out adjustment.
Helpful Hint (
N
/
NORMALIZE
Normalization)
While the PICTURE POS./SIZE display is active, if either the N button on the remote control is pressed at any time or the
(ACTION button) is pressed during “NORMALIZE”, then all adjustment values are returned to the factory settings.
25
SOUND Adjustment
1
SOUND
Press to display the Sound menu.
INPUT
SURROUND
2
Select to adjust each item.
VOL
Press to select the desired adjustment menu.
R
N
Select the desired level by listening to the sound.
PICTURE
SOUND
SET UP
PICTURE
POS S
BASS
Adjusts low sounds
SOUND
NORMALIZE
AUDIO MENU
BASS
TREBLE
BALANCE
SURROUND
TREBLE
Adjusts high sounds
BALANCE
Adjusts left and right
volumes
NORMAL
STANDARD
0
0
0
ON
STANDARD
AUTO
Emits the original sound.
Automatically controls
proper volume level.
SURROUND (see next page)
Select ON or OFF
• To end adjustments
R
Press the R button
Note:
Press the SURROUND button to directly turn the surround effect ON and OFF. (see next page)
BASS, TREBLE and SURROUND settings are memorized separately for each SOUND mode (STANDARD, AUTO).
Helpful Hint (
N
/
NORMALIZE
Normalization)
While the “SOUND” menu is displayed, if either the N button on the remote control is pressed at any time or the
(ACTION button) is pressed during “NORMALIZE”, then all adjustment values are returned to the factory settings.
MUTE
Useful when answering the phone or receiving visitors.
Press this button to mute the sound.
Press again to reactivate sound. Sound is also reactivated when power is turned off or
volume level is changed.
26
SURROUND Controls
SURROUND
INPUT
SURROUND Button
The benefits of surround sound are enormous. You can be
completely enveloped in sound; just as if you were at a concert
hall or cinema.
The surround setting switches on and off each time the
SURROUND button is pressed.
ON
SURROUND
OFF
VOL
N
R
PICTURE
SOUND
SET UP
SURROUND
PICTURE
POS. /SIZE
ASPECT
ON
Note:
The surround settings are memorized separately for each SOUND mode
(STANDARD, AUTO).
OFF TIMER
PC
27
PICTURE Adjustments
1
2
PICTURE
PICTURE
Press the PICTURE button on the
Remote Control to display the
PICTURE menu.
NORMALIZE NORMAL
PICTURE MENU
PICTURE
BRIGHTNESS
COLOR
TINT
SHARPNESS
COLOR TEMP
ADVANCED SETTINGS
Select to adjust each item.
Press to select the menu to adjust.
STANDARD
20
0
0
0
0
NORMAL
ON
Select the desired level by looking at the picture
behind the menu.
Press the left
modes.
PICTURE
NORMALIZE NORMAL
PICTURE MENU
PICTURE
BRIGHTNESS
COLOR
TINT
SHARPNESS
COLOR TEMP
ADVANCED SETTINGS
button to switch between
STANDARD
STANDARD
20
0
0
0
0
NORMAL
ON
DYNAMIC
CINEMA
STANDARD
For viewing in standard (evening lighting)
environments.
This menu selects the normal levels of
BRIGHTNESS and PICTURE.
Press the left or right button to
select “ON”. Press the down button
to enter ADVANCED SETTINGS mode.
ADVANCED SETTINGS ON
Enables fine picture adjustment at a
professional level (see next page).
DYNAMIC
For viewing in brighter environments.
This menu selects higher than normal levels of
BRIGHTNESS and PICTURE.
CINEMA
Ideal for movies.
Note:
If you would like to change the picture and color of the
selected PICTURE menu to something else, adjust using
the items in the PICTURE menu. (see next page)
ADVANCED SETTINGS
NORMALIZE
BLACK EXTENSION
W/B HIGH R
W/B HIGH B
W/B LOW R
W/B LOW B
GAMMA
or right
NORMAL
0
0
0
0
0
Press the left or right button to switch between
modes.
NORMAL
COOL
WARM
2. 2
ADVANCED SETTINGS OFF
Displays images with settings of the
PICTURE menu.
Helpful Hint ( N /
NORMALIZE
Normalization)
While the “PICTURE” menu is displayed, if either the N button on the remote control is pressed at any time or the
(ACTION button) is pressed during “NORMALIZE”, then all adjustment values are returned to the factory settings.
28
PICTURE Adjustments
Item
Effect
Adjustments
Adjusts the proper picture contrast.
PICTURE
Less
More
BRIGHTNESS
Darker
Brighter
Adjusts color saturation.
COLOR
Less
TINT
(NTSC only)
Adjusts for easier viewing of dark pictures
such as night scenes and black hair.
More
Adjust for natural flesh tones.
Reddish
Greenish
Adjusts picture sharpness.
SHARPNESS
Less
More
Notes:
(1) “COLOR” , “TINT” and “SHARPNESS”
settings cannot be adjusted for “RGB”
and “PC” input signal modes.
(2) You can change the level of each
function (PICTURE, BRIGHTNESS,
COLOR, TINT, SHARPNESS) for each
PICTURE menu.
(3) The setting details for STANDARD,
DYNAMIC and CINEMA respectively
are memorized separately for each
input mode (VIDEO (S VIDEO),
COMPONENT RGB and PC).
(4) The “TINT” setting can be adjusted for
NTSC signal only during “VIDEO
(S VIDEO)” input signal.
Note:
In PICTURE, there is nor a noticeable change even when contrast is increased with a bright picture or reduced with a dark
picture.
ADVANCED SETTINGS
Item
BLACK
EXTENSION
Effect
Details
Adjusts the dark shades of the image in gradiation.
Less
More
Less
More
Less
More
Less
More
Less
More
Down
Up
W/B HIGH R
Adjusts the white balance for light red areas.
W/B HIGH B
Adjusts the white balance for light blue areas.
W/B LOW R
Adjusts the white balance for dark red areas.
W/B LOW B
Adjusts the white balance for dark blue areas.
GAMMA
2.0
2.2
2.5
Notes:
(1) Carry out “W/B” adjustment as follows.
A Adjust the white balance of the bright sections using the “W/B HIGH R” and “W/B HIGH B” settings.
B Adjust the white balance of the dark sections using the “W/B LOW R” and “W/B LOW B” settings.
C Repeat steps A and B to adjust.
Steps A and B affect each other’s settings, so repeat each step in turn to make the adjustment.
(2) The adjustment values are memorized separately for each input mode (VIDEO(S VIDEO), COMPONENT, RGB and PC).
(3) The adjustment range values should be used as an adjustment reference.
Helpful Hint (
N
/
NORMALIZE
Normalization)
On the remote control unit, while the “ADVANCED SETTINGS” menu is displayed, if either the N button is pressed at
any time or the
(ACTION button) is pressed during “NORMALIZE”, then all adjustment values are returned to the
factory settings.
29
SET UP TIMER
The timer can switch the Plasma Display ON or OFF.
Before attempting Timer Set, confirm the PRESENT TIME OF DAY and
adjust if necessary. Then set POWER ON TIME/POWER OFF TIME.
Display the SET UP TIMER screen
1
SET UP
Press to display the
SETUP menu screen.
INPUT
SURROUND
2
VOL
N
Press to select
SET UP TIMER.
SET UP
COMPONENT/RGB-IN SELECT
RGB
SIGNAL
SCREENSAVER
ENGLISH (US)
OSD LANGUAGE
SET UP TIMER
R
SET UP TIMER
PICTURE
SOUND
Press to display the
SET UP TIMER
screen.
SET UP
PRESENT TIME
POWER ON FUNCTION
POWER ON TIME
POWER OFF FUNCTION
POWER OFF TIME
0:52
OFF
0:00
OFF
0:00
PRESENT TIME OF DAY Set
To set up PRESENT TIME, follow the procedure described below.
1
Press to select PRESENT TIME OF DAY.
PRESENT TIME SETUP
PRESENT TIME OF DAY
HOURS ADJUSTMENT
MINUTES ADJUSTMENT
99 : 99
00
00
Press to display the PRESENT TIME OF
DAY SETTING screen.
2
Press to select HOURS ADJUSTMENT/
MINUTES ADJUSTMENT.
Press to set up Hours or Minutes.
button: Forward
button: Back
Press to complete PRESENT TIME OF
DAY setup.
30
PRESENT TIME SETUP
PRESENT TIME OF DAY
HOURS ADJUSTMENT
MINUTES ADJUSTMENT
0 : 52
00
52
TIMER Set
Press to select
POWER ON TIME/
POWER OFF TIME.
1
SET UP TIMER
PRESENT TIME OF DAY
POWER ON FUNCTION
POWER ON TIME
POWER OFF FUNCTION
POWER OFF TIME
0:52
OFF
0:00
OFF
0:00
Press to display the POWER ON SET
UP / POWER OFF SET UP screen.
Press to select HOURS ADJUSTMENT/
MINUTES ADJUSTMENT.
2
Press to adjust each time.
POWER ON SETUP
POWER ON FUNCTION
HOURS ADJUSTMENT
MINUTES ADJUSTMENT
0 : 52
00
52
POWER OFF SETUP
Press to complete POWER ON TIME/
POWER OFF TIME, and return to the
SET UP TIMER screen.
3
POWER OFF TIME
HOURS ADJUSTMENT
MINUTES ADJUSTMENT
Press to select POWER ON FUNCTION/
POWER OFF FUNCTION.
SET UP TIMER
Press to select ON.
PRESENT TIME OF DAY
POWER ON FUNCTION
POWER ON TIME
POWER OFF FUNCITON
POWER OFF TIME
0 : 00
00
00
0:52
ON
0:00
ON
0:00
Press to store setting.
4
R
Press twice to exit from SETUP.
Note :
Timer function will not work unless “PRESENT TIME OF DAY” is set.
31
SCREENSAVER (For preventing after-images)
Do not display a still picture, especially in 4:3 mode, for any length of time.
If the display must remain on, a SCREENSAVER should be used.
1
SET UP
Press to display the SETUP menu screen.
2
Press to select the SCREENSAVER.
SET UP
COMPONENT/RGB-IN SELECT
RGB
SIGNAL
SCREENSAVER
ENGLISH (US)
OSD LANGUAGE
SET UP TIMER
Press to select the SCREENSAVER screen.
NEGATIVE / SCROLL selection
3
Press to select the Function.
SCREENSAVER
Press to select the desired function.
WHITE BAR SCROLL
NEGATIVE
FUNCTION
MODE
SHOW DURATION
SAVER DURATION
SIDE BAR ADJUST
WHITE BAR SCROLL
INTERVAL
0:00
0:00
BRIGHT
WHITE BARSCROLL : A white bar will scroll from left to right.
NEGATIVE
: A negative image will be displayed on the screen.
MODE selection
4
Press to select the MODE.
SCREENSAVER
WHITE BAR SCROLL
TIME OF DAY
0:00
0:00
MID
FUNCTION
MODE
START TIME
FINISH TIME
SIDE BAR ADJUST
Press to select ON or OFF.
OFF
INTERVAL : Operates when SHOW DURATION and SAVER DURATION are set
up and those times arrive.
TIME OF DAY : Operates when START TIME and FINISH TIME are set up and those
times arrive.
ON : Operates when the
(ACTION) is pressed.
To stop the SCREENSAVER under ON, press the
R
button.
If the MODE is at ON, the menu screen will disappear and the SCREENSAVER will be activated.
After selecting TIME OF DAY or INTERVAL, the relevant SET UP TIME will become available for selection and the
OPERATING TIME may be set. (Time cannot be set when “MODE” is “ON” or “OFF.”)
SCREENSAVER
SCREENSAVER
FUNCTION
MODE
SHOW DURATION
SAVER DURATION
SIDE BAR ADJUST
32
WHITE BAR SCROLL
INTERVAL
0:00
0:00
HIGH
FUNCTION
MODE
START TIME
FINISH TIME
SIDE BAR ADJUST
SCREENSAVER
WHITE BAR SCROLL
TIME OF DAY
0:00
0:00
MID
FUNCTION
MODE
SHOW DURATION
SAVER DURATION
SIDE BAR ADJUST
WHITE BAR SCROLL
OFF
0:00
0:00
HIGH
SCREENSAVER
Setup of SCREENSAVER Time
Press to select START TIME/ FINISH TIME
(When TIME OF DAY is selected).
Press to select SHOW DURATION/ SAVER
DURATION (When INTERVAL is selected).
5
START TIME
START TIME
HOURS ADJUSTMENT
MINUTES ADJUSTMENT
Press to select each time adjustment screen.
FUNCTION
MODE
SHOW DURATION
SAVER DURATION
SIDE BAR ADJUST
FUNCTION
MODE
START TIME
FINISH TIME
SIDE BAR ADJUST
WHITE BAR SCROLL
INTERVAL
0:00
0:00
HIGH
FINISH TIME
FINISH TIME
HOURS ADJUSTMENT
MINUTES ADJUSTMENT
SCREENSAVER
SCREENSAVER
WHITE BAR SCROLL
TIME OF DAY
0:00
0:00
MID
0:00
00
00
0:00
00
00
PERIODIC TIME
Press to select HOURS ADJUSTMENT/
MINUTES ADJUSTMENT.
6
SHOW DURATION
HOURS ADJUSTMENT
MINUTES ADJUSTMENT
Press to set up HOURS or MINUTES.
0:00
00
00
OPERATING TIME
button: Forward
button: Back
SAVER DURATION
HOURS ADJUSTMENT
MINUTES ADJUSTMENT
0:00
00
00
Press to store settings.
Note :
Timer function will not work unless “PRESENT TIME OF DAY” is set.
SIDE BAR ADJUST
Do not display a picture in 4:3 mode for an extended period, as this can cause an after-image to remain on the side bars
on either side of the display field.
To prevent the appearance of such an after-image, change the brightness of the side bars.
1
To display the SCREENSAVER screen.
(Refer to page 32, operation guide steps 1 and 2)
4:3
Screen Display
Press to select the
SIDE BAR ADJUST.
2
side bars
after-images
Press to select
OFF, DARK, MID, BRIGHT.
SCREENSAVER
OFF
DARK
MID
R
3
Press to exit from SCREENSAVER.
BRIGHT
FUNCTION
MODE
SHOW DURATION
SAVER DURATION
SIDE BAR ADJUST
WHITE BAR SCROLL
INTERVAL
0:00
0:00
MID
Notes:
• Setting the side bar to BRIGHT mode for an extended period may result in occurence of after-images.
• The side bars may flash (alternate black/white) depending on the picture being shown on the screen. In such
an occurrence, use the Cinema mode.
33
SET UP for Input Signals
COMPONENT/RGB IN SELECT
Select to match the signals from the source connected to the COMPONENT/RGB input terminals.
Y, PB, PR signals
“COMPONENT”
R, G, B, HD, VD signals
“RGB”
1
SET UP
Press to display the SET UP menu screen.
INPUT
Press to select the “COMPONENT/RGB IN
SELECT”.
2
SURROUND
VOL
Press to select the desired mode.
R
N
SET UP
COMPONENT/RGB-IN SELECT
PICTURE
SOUND
RGB
SIGNAL
SCREENSAVER
ENGLISH (US)
OSD LANGUAGE
SET UP TIMER
SET UP
COMPONENT
PICTURE
POS. /SIZE
RGB
R
ASPECT
Press to exit from adjust mode.
3D Y/C FILTER – For NTSC Video images
Select “SIGNAL” from the “SET UP” menu during VIDEO (S VIDEO) input signal mode.
(“SIGNAL [VIDEO]” menu is displayed.)
SET UP
Press to select the “3D Y/C FILTER (NTSC)”
Press to set ON/OFF.
COMPONENT/RGB-IN SELECT
RGB
SIGNAL
SCREENSAVER
ENGLISH (US)
OSD LANGUAGE
SET UP TIMER
Press
(ACTION) button
SIGNAL
R
Press to exit from adjust mode.
Note:
When on, this setting only affects NTSC input signals.
34
3D Y/C FILTER (NTSC)
COLOR SYSTEM
3:2 PULLDOWN
AUTO (4:3 )
[ VIDEO ]
ON
AUTO
OFF
NORMAL
SET UP for Input Signals
COLOR SYSTEM / AUTO
Select SIGNAL from the “SET UP” menu during VIDEO (S VIDEO) input signal mode.
(“SIGNAL [VIDEO]” menu is displayed.)
SET UP
COMPONENT/RGB-IN SELECT
Press to select the “COLOR SYSTEM” or “AUTO”.
Press to select each function.
RGB
SIGNAL
SCREENSAVER
ENGLISH (US)
OSD LANGUAGE
SET UP TIMER
Press
If the image becomes unstable:
With the system set on Auto, under conditions of
low level or noisy input signals the image may in
rare cases become unstable. Should this occur,
set the system to match the format of the input
signal.
Mode
Color system
[ VIDEO ]
SIGNAL
3D Y/C FILTER (NTSC)
COLOR SYSTEM
3:2 PULLDOWN
AUTO (4:3 )
ON
AUTO
OFF
NORMAL
Function
Set the color system to match the input signal. If set to “AUTO”, the color system is
determined automatically.
AUTO
AUTO (4:3)
(ACTION) button
PAL
SECAM
M NTSC
NTSC
Set to “NORMAL” to view 4:3 images in an unchanged format when AUTO is selected.
If you would like to view 4:3 images in “Just” format, set to “JUST”.
3:2 PULLDOWN
When on, the display attempts to reproduce a more natural interpretation of sources such as movie pictures, which are
recorded at 24 frames per second.
If the picture is not stable, turn the setting to off.
SET UP
Select “SIGNAL” from the “SET UP” menu during VIDEO (S VIDEO) or
COMPONENT input signal mode. (“SIGNAL [VIDEO]” menu is displayed.)
Press to select 3:2 PULLDOWN.
Press to set ON/OFF.
COMPONENT/RGB-IN SELECT
RGB
SIGNAL
SCREENSAVER
ENGLISH (US)
OSD LANGUAGE
SET UP TIMER
Press
(ACTION) button
SIGNAL
Note:
When ON, this setting only affects the following signal input.
• NTSC signal input during “VIDEO (S VIDEO)” input signal mode.
• 525i(480i) signal input during “COMPONENT” input signal mode.
3D Y/C FILTER (NTSC)
COLOR SYSTEM
3:2 PULLDOWN
AUTO (4:3 )
SIGNAL
R
3:2 PULLDOWN
[ VIDEO ]
ON
AUTO
OFF
NORMAL
[ COMPONENT ]
OFF
Press to exit from adjust mode.
35
SET UP for Input Signals
SYNC
Select SIGNAL from the “SET UP” menu during RGB or PC input signal mode.
SET UP
COMPONENT/RGB-IN SELECT
Press to adjust.
RGB
SIGNAL
SCREENSAVER
ENGLISH (US)
OSD LANGUAGE
SET UP TIMER
Press
(ACTION) button
[ RGB ]
SIGNAL
H&V
SYNC
R
H-FREQ.
V-FREQ.
Press to exit from adjust mode.
31.5 kHz
60.0 Hz
[ PC ]
SIGNAL
H&V
SYNC
H-FREQ.
V-FREQ.
31.5 kHz
60.0 Hz
Setting RGB sync signal
Confirm that the input is set to RGB INPUT (this setting is valid only for RGB INPUT).
H & V:
The H and V sync signals are input from the HD/VD connector.
ON G:
Uses a synchronized signal on the Video G signal, which is input
from the G connector.
ON VIDEO: The composite video signal input from the VIDEO input terminal is
used by dividing the sync signals.
SYNC
H&V
SYNC
ON G
SYNC
ON VIDEO
Setting PC sync signal
Confirm that the input is set to PC INPUT (this setting is valid only for PC INPUT).
H & V: The H and V sync signals are input from the HD/VD connector.
ON G: Uses a synchronized signal on the Video G signal, which is input from
the G connector.
SYNC
H&V
SYNC
ON G
H-FREQ (kHz)/V-FREQ (Hz)
Displays the H (Horizontal)/V (Vertical) frequencies.
This display is valid only for RGB input and PC input.
Display range:
Horizontal 15.6 - 110 kHz
Vertical
48 - 120 Hz
36
H-FREQ.
V-FREQ.
31.5 kHz
60.0 Hz
Troubleshooting
Before you call for service, determine the symptoms and make a few simple checks as shown below.
Symptoms
Picture
Checks
Sound
Electrical Appliances
Cars/Motorcycles
Fluorescent light
Interference
Noisy Sound
Volume
(Check whether the mute function has been
activated on the remote control.)
Normal Picture
No Picture
No Sound
No Sound
Not plugged into AC outlet
Not switched on
PICTURE and BRIGHTNESS/Volume setting
(Check by pushing the power switch or
stand-by button on the remote control.)
If a signal with a non-applicable color system
format, or frequency is input, only the input
terminal indication is displayed.
No Picture
Normal Sound
Color controls set at minimum level.
(see page 28, 29)
Color system (see page 35)
No Color
Plasma display panel
Symptoms
Some parts of the screen do
not light up
Normal Sound
Check
The plasma display panel is manufactured using an extremely high level of precision
technology, however, sometimes some parts of the screen may be missing picture
elements or have luminous spots. This is not a malfunction.
Do not allow a still picture to be displayed for an extended period, as this can
cause a permanent after-image to remain on the plasma display.
Examples of still pictures include logos, video games, computer images, teletext
and images displayed in 4:3 mode.
After-images appear
Whirring sounds can be heard
from the display unit.
Note:
The permanent after-image on the plasma display resulting from fixed image use
is not an operating defect and as such is not covered by the Warranty.
This product is not designed to display fixed images for extended periods of time.
The display unit is fitted with a cooling fan to dissipate heat generated during normal
use.The whirring sound is caused by rotation of the fan and is not a malfunction.
37
Specifications
PDM-1
Power Source
Power Consumption
120 V AC, 50/60 Hz
Maximum
Stand-by condition
Power off condition
plasma display panel
Contrast Ratio
Screen size
5.5 A
2.4 W
0.9 W
Drive method AC type
50-inch, 16:9 aspect ratio
3000:1
1,106 mm (W) × 622 mm (H) × 1,269 mm (diagonal)
No. of pixels
1,049,088 (1,366 (W) × 768 (H)) [ 4,098 × 768 dots]
Operating condition
34 °F - 104 °F (0 °C - 40 °C)
20 % - 80 %
Temperature
Humidity
Applicable signals
Color System
Scanning format
PC signals
NTSC, PAL, PAL60, SECAM, Modified NTSC
525i (480i), 625i (575i), 525p (480p), 625p (575p), 750p (720p), 1,125/60i, 50i, 24p,
24SF (1,080/60i, 50i, 24p, 24SF) ············· SMPTE 274M
XGA display
VGA, SVGA, XGA
SXGA, UXGA (compressed)
Horizontal scanning frequency 15.6 - 110 kHz
Vertical scanning frequency 48 - 120 Hz
Connection terminals
AV
COMPONENT/RGB
Video IN (RCA)
S VIDEO IN (MINI DIN 4PIN)
AUDIO IN (RCA PIN JACK × 2)
Y/G (RCA)
PC
PB/B (RCA)
PR/R (RCA)
HD (RCA)
VD (RCA)
AUDIO IN (RCA PIN JACK × 2)
(HIGH-DENSITY D-SUB 15PIN)
SERIAL
38
AUDIO IN (M3.5 JACK)
EXTERNAL CONTROL TERMINAL (D-SUB9PIN)
1.0 Vp-p (75-ohm)
Y: 1 Vp-p (75-ohm), C: 0.286 Vp-p (75-ohm)
0.5 Vrms (high impedance)
1.0 Vp-p/composite (75-ohm)
0.7 Vp-p/non-composite (75-ohm)
0.7 Vp-p (75-ohm)
0.7 Vp-p (75-ohm)
1.0 - 5.0 Vp-p (high impedance)
1.0 - 5.0 Vp-p (high impedance)
0.5 Vrms (high impedance)
R,G,B/0.7 Vp-p (75-ohm)
HD, VD/1.0 - 5.0 Vp-p (high impedance)
0.5 Vrms (high impedance)
RS-232C COMPATIBLE
Specifications
PDM-1
Accessories Supplied
Remote Control Transmitter
Batteries
Ferrite core
Fixing bands
Speaker Wire
2 × AA Size
(small size) × 1, (large size) × 2
2 pcs
Optional Supplied
Speakers(main speaker)
Speakers(center speaker)
Pedestal
Wall-mounting unit
Dimensions
(W × H × D)
NS-F100, NS-F80, NS-F70
NS-CF100
PDS-150
PWK-150
47.6” (1,210 mm) × 28.5” (724 mm) × 3.9” (98 mm)
3.9"
(98 mm)
28.5" (724 mm)
47.6" (1,210 mm)
POWER
/
R - STANDBY
INPUT
–
VOL
+
G POWER ON
Mass (Weight)
approx. 94.8 lbs (main unit only)
Note:
Design and specifications are subject to change without notice. Weight and dimensions shown are approximate.
39
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in Japan
V707760-2
Download PDF

advertising