Yamaha | PDM-4210E | User's Manual | Yamaha PDM-4210E User's Manual

G
PDM-4210E
2004
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
All rights reserved.
Printed in Japan
QR60131
PDM-4210E
High definition plasma monitor
Moniteur plasma haute définition
USER'S MANUAL
MANUEL UTILISATEUR
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUAL DE USUARIO
011_PDM-4210_G_EN_Caution
2003.12.24 01:09
ページ 1
(ブラック 版)
ENGLISH
USER'S MANUAL
Thank you very much for purchasing the Yamaha High Definition
Plasma Monitor.
Before using your monitor, please carefully read this manual so you
will know how to operate the monitor properly. Keep this manual in a
safe place. You will find it useful in the future.
Notes on lnstallation Work:
This product is marketed assuming that it is installed by qualifed
personnel with enough skill and competence. Always have an
installation specialist or your dealer install and set up the product.
YAMAHA cannot assume liabilities for damage caused by mistake
in installation or mounting, misuse, modification or a natural
disaster.
Note for Dealers:
After installation, be sure to deliver this manual to the customer
and explain to the customer how to handle the product.
Notes about This Manual
• This information in this manual is subject to change without
notice.
• While meticulous care has been taken in the preparation of this
manual, you are requested to notify your dealer or us should
you have any comments, views or questions about our
product.
• Fully understand the prerequisites to using the product, such
as hardware and software specifications and constraints, in
using the product. We are not held liable for damages caused
by improper handling of the product.
• Reproduction of this manual in whole or in part without our prior
written permission is prohibited.
• The product names mentioned in this manual may be
trademarks or registered trademarks of their respective
owners.
READ ALL INSTRUCTIONS CAREFULLY.
KEEP THIS USER'S MANUAL FOR FUTURE REFERENCE.
For future reference, record the serial number of your monitor.
SERIAL NO.
The serial number is located on the rear of the monitor.
1
011_PDM-4210_G_EN_Caution
2003.12.24 01:09
ページ 2
(ブラック 版)
FEATURES
Large-screen, high-definition plasma display
panel
The 42-inch colour plasma display panel, with a resolution of 1024
(H) x 1024(V) pixels, creates a high-definition, large-screen (aspect
ratio : 16:9) and low-profile flat display. Free from electromagnetic
interferences from geomagnetic sources and ambient power lines,
the panel produces high-quality display images free from colour
misconvergence and display distortion.
High Performance Digital Processor
A wide range of personal computer signals can be handled, from
640 x 400, 640 x 480 VGA to 1600 x 1200 UXGA.
Easy-to-use remote control and on screen
display system
The remote control included eases the work of setting display controls.
Further, the on-screen display system, displays the status of signal
reception and display control settings in an easy-to-view fashion.
TruBass
TruBass, SRS and (O) symbol are trademarks of SRS Labs,Inc.
TruBass technology is incorporated under license from SRS Labs,
Inc.
About the Optional Video Unit
The following functions can be obtained by connecting the optional video
unit.
(1) A Composite/S video terminal and two component terminals have
been added. A composite video output terminal is also provided
as a monitoring output.
(2) A wide range of devices other than personal computers can also
be connected.
(3) It is possible to swich the component terminal to RGB input from
the Menu screen.
(4) A SCART terminal is also provided for the signal of the European
standard. It operates as composite/S/RGB input terminal, or
video output terminal.
Options
Ask your local retail dealer for further details on the following optional
attachments.
• Wall Mounting Unit
PWK-242
• Video Unit
PTB-4210
• This User’s Manual was printed before final product development.
After printing, some product specifications may change due to
operational upgrades and other reasons. In this case, the
specifications of the product itself will take precedence over the
specifications in this manual.
• TRADEMARK ACKNOWLEDGEMENT
VGA and XGA are registered trademarks of International Business
Machines Corporation.
APPLE and Macintosh are registered trademarks of Apple
Computer, Inc.
All brand or product names are trademarks or registered
trademarks of their respective holders.
2
CONTENTS
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
CAUTION: READ THIS
BEFORE OPERATING YOUR UNIT. . . . . 3
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . .
7
COMPONENT NAMES . . . . . . . . . . . . . . . . . . . .
8
Main Unit ..........................................
Remote control ......................................
Loading Batteries ..................................
Handling the Remote Control ........................
INSTALLATION INSTRUCTIONS.. . . . . . . . . .
Installation ........................................
Anti-tumble measures ..............................
Connecting to a PC ................................
Power Cord Connection ............................
OPERATING INSTRUCTIONS . . . . . . . . . . . .
Turning Power On and Off ..........................
Input Switching ....................................
Volume Adjustment ................................
Audio Mute ........................................
Size Switching ....................................
Input Signal Screen Display ........................
Automatic Adjustment of Screen Position and the Clock
Independent Operation of Multiple Monitors ..........
Using the Menu Screen ............................
PICTURE MENU....................................
AUDIO MENU......................................
TIMER MENU ......................................
FUNCTION MENU ..................................
SETUP MENU ......................................
LANGUAGE MENU ................................
OTHER FEATURES . . . . . . . . . . . . . . . . . . . . . .
Automatic Store ....................................
Signal Check ......................................
Power Save Mode ..................................
IMAGE RETENTION OF
PLASMA DISPLAY PANEL . . . . . . . . . .
NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . .
8
9
9
9
10
10
10
11
12
13
13
14
14
14
15
15
16
16
16
17
18
18
19
20
21
21
21
22
22
23
23
24
Symptoms That Appear to be Failures ................
Actions to Correct Abnormal Displays ................
24
26
PRODUCT SPECIFICATIONS . . . . . . . . . . . .
27
Signal Input........................................
Recommended Signal List ..........................
27
28
SUPPLEMENT . . . . . . . . . . . . . . . . . . . . . . . . . .
30
Optional Video Unit Function ........................
Optional Tuner Unit Function ........................
31
43
011_PDM-4210_G_EN_Caution
2003.12.24 01:09
ページ 3
(ブラック 版)
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
ENGLISH
This Plasma monitor has been designed and manufactured to meet international safety standards, but like any electrical equipment, care must
be taken if you are to obtain the best results and safety is to be assured.
Before using this product, please read and understand the Safety Instructions thoroughly to ensure correct usage, and follow all the
instructions.
Never use the monitor if a problem occurs.
Abnormal operations such as smoke, strange odor, no image, no sound, excessive sound, damaged casing, elements, cables, penetration of
liquids or foreign matter, etc. can cause a fire or electrical shock.
In such case, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure that the smoke
or odor has stopped, contact your dealer. Never attempt to make repairs yourself because this could be dangerous.
Do not insert liquids or foreign objects.
Penetration of liquids or foreign objects could result in fire or electrical shock. Use special caution in households where children are present.
If liquids or foreign objects should enter the projector, immediately turn off the power switch, disconnect the power plug from the power outlet
and contact your dealer.
• Do not place the monitor in a bathroom.
• Do not expose the monitor to rain or moisture.
• Do not place flower vases, pots, cups, cosmetics, liquids such as water, etc on or around the monitor.
• Do not place metals, combustibles, etc on or around the monitor.
Never disassemble or modify the monitor.
The monitor contains high voltage components. Modification could result in fire or electrical shock.
• Never remove any fixed cover.
Do not give the monitor any shock or impact.
If the monitor should be shocked and/or broken, it could result in an injury, and continued use could result in fire or electrical shock.
If the glass panel is broken or damaged, immediately turn off the power switch, disconnect the power plug from the power outlet and contact
your dealer.
Do not place the monitor on an unstable surface.
If the monitor should be dropped and/or broken, it could result in an injury, and continued use could result in fire or electrical shock.
• Do not place the monitor on an unstable, slanted or vibranting surface such as a wobbly or inclined stand.
Do not obstruct the ventilation of the monitor.
If the ventilation is obstructed during the operation of the monitor or just after switching off the power, it could result in damage and shorten the
lifespan of your monitor due to overheating. Make sure there is ample ventilation.
• Keep a space of 100mm (10cm) or more between the sides, rear and top of the monitor and other objects such as walls.
• Do not place anything around ventilation openings of the monitor.
• Never block ventilation openings.
• Do not put the plasma display panel side up.
• Do not cover the monitor with a tablecloth, etc.
• Do not place the monitor on a carpet or bedding, or near a curtain.
Use only the correct power outlet.
Incorrect power supply could result in fire or electrical shock. Use only the correct power outlet depending on the indication on the monitor and
the safety standard.
• The enclosed power cord must be used depending on the power outlet to be used.
Be cautious of the power cord connection.
Incorrect connection of the power cord could result in fire or electrical shock.
• Do not touch the power cord with a wet hand.
• Check that the connecting portion of the power cord is clean (with no dust), before using. Use a soft and dry cloth to clean the power plug.
• Insert the power plug into a power outlet firmly. Avoid using a loose, unsound outlet or contact failure.
• Do not cut off the fitted power plug, the removal of which could lead to impaired performance. If you wish to extend the lead, obtain an
appropriate extension lead or consult your dealer.
• Should you require replacing the fuse in the molded plug with a new fuse, then please replace with new one of the same value, type and
approval as the original. Ensure the fuse cover is returned to its original position.
Be sure to keep safety ground connection.
Connect the ground terminal of AC inlet of this monitor with the ground terminal provided at the power outlet using the enclosed power cord. If
the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet.
Be careful in handling the power cord and external connection cables.
If you keep using a damaged the power cord or cables, it can cause a fire or electrical shock. Do not apply too much heat, pressure or tension
to the power cord and cables.
If the power cord or cables are damaged (exposed or broken core wires, etc.), contact your dealer.
• Do not place the monitor or heavy objects on the power cord and cables. Also, do not place a spread, cover, etc, over them because this
could result in the inadvertent placing of heavy objects on the concealed power cord or cables.
• Do not pull the power cord and cables. When connecting and disconnecting the power cord or cables, do it with your hand holding the plug
or connector.
• Do not place the cord near the heater.
• Do not touch the power plug just after disconnecting it from the power outlet to prevent electric shock.
• Do not touch the power plug when lightening is close to you.
• Avoid coiling the power cord and bending it sharply.
• Protect the power cord from being walked on, pinched particularly at plugs, conveniences receptacles, and the point where they exit from the
apparatus.
• Do not modify the power cord.
3
011_PDM-4210_G_EN_Caution
2003.12.24 01:09
ページ 4
(ブラック 版)
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. (continued)
Be careful in handling the battery of the remote control.
Incorrect handling of the battery could result in fire or personal injury. The battery may explode if not handled properly.
• Keep the battery away from children and pets. If swallowed consult a physician immediately for emergency treatment.
• Do not allow the battery to be exposed to fire or water.
• Avoid fire or high-temperature environment.
• Do not hold the battery with metallic tweezers.
• Keep the battery in a dark, cool and dry place.
• Do not short circuit the battery.
• Do not recharge, disassemble or solder the battery.
• Do not physically impact the battery.
• Use only the battery specified in the manual of this monitor.
• Make sure the plus and minus terminals are correctly aligned when loading the battery.
• If you observe a leakage of the battery, wipe out the liquid and then replace the battery. If the liquid adheres your body or clothes, rinse well
with water.
• Obey the local laws on disposing the battery.
FOR THE CUSTOMERS IN THE U.K.
THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE U.K. PLEASE REFER TO THE
NOTES ON THIS PAGE.
IMPORTANT FOR UNITED KINGDOM
WORDING FOR CLASS I EQUIPMENT INSTRUCTION BOOKS AND LABELS
The mains lead on this equipment is supplied with a molded plug incorporating a fuse, the value of which is indicated on the pin face of the plug.
Should the fuse need to be replaced, an ASTA or BSI approved BS 1362 fuse must be used of the same rating. If the fuse cover is detachable
never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of
the plug. Fuse covers are available from your dealer.
DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to
reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.
Should it be necessary to change the mains plugs, this must be carried out by a competent person, preferably a qualified electrician.
If there is no alternative to cutting off the mains plug, ensure that you dispose of it immediately, having first removed the fuse, to avoid a possible
shock hazard by inadvertent connection to the mains supply.
WARNING: THIS EQUIPMENT MUST BE EARTHED IMPORTANT
The wires in the mains lead are coloured in accordance with the following code :
Green and Yellow = Earth, Blue = Neutral, Brown = Live.
As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN and YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the earth
symbol
or coloured GREEN or GREEN and YELLOW.
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN
must be connected to the terminal marked with the letter L or coloured BROWN or RED.
Green & Yellow
to Earth
Brown to Live
Fuse
Blue to Neutral
Cord Clamp
Be careful in moving the monitor.
Neglect could result in an injury or damage.
• Do not move the monitor during use. Before moving, disconnect the power plug and all external connections.
• You are advised to move the monitor with two persons.
• Avoid any impact or shock to the monitor; particularly take care of glass screen.
Do not put anything on top of the monitor.
Placing anything on the monitor could result in loss of balance or falling, and cause an injury or damage. Use special caution in households
where children are present.
Avoid a humid or dusty place.
Placing the monitor in a smoke, a highly humid, dusty place, oily soot or corrosive gas could result in fire or electrical shock.
• Do not place near the kitchen, a humidifier or other place where there is oil, smoke or humidity.
Avoid a high temperature environment.
The heat could have adverse influence on the monitor and other parts, and could result in transformation, melting or fire.
• Do not place the monitor, the remote control and other parts in direct sunlight or near a hot object such as heater, etc.
• Do not put the monitor in a place where the temperature is widely changing.
4
011_PDM-4210_G_EN_Caution
2003.12.24 01:09
ページ 5
(ブラック 版)
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. (continued)
ENGLISH
Remove the power cord for complete separation.
• For safety purposes, disconnect the power cord if the monitor is not to be used for prolonged periods of time.
• Before cleaning, turn off and unplug the monitor. Neglect could result in fire or electrical shock.
Installation environment
Do not obstruct a ventilation hole.
Do not put the monitor on carpet or blanket, or near a curtain which has a possibility of obstructing a ventilation hole of the monitor.
Do not put the monitor in the following places.
• Hot places such as near heater, place exposed to the direct rays of the sun.
• A place where the temperature is widely changing.
• Places with soot, dust or high humidity.
• Poor air ventilation place.
• Place near fire.
• A wet place such as bathroom, or shower room.
• Place where you can trip over it.
• Always vibrating or strongly vibrating places.
• Distorted or unstable places.
How to view the monitor
If you use the monitor in too dark a room, your eyes may become tired.
Please use it in a reasonably bright room.
Avoid direct rays of the sun to the screen in order to prevent eye fatigue.
Your eyes will get fatigued after viewing the monitor for long period of time.
Relax your eyes by viewing away from the monitor from time to time.
Please watch the monitor in downward direction.
Note on image retention
The plasma monitor illuminates phosphor to display images. The phosphor has a finite illumination life. After extended periods of illumination, the
brightness of the phosphor will be degraded to such extent that stationary images would burn-in that part of the screen as grayed-out images.
Tips to prevent such image retention are:
- Do not display images having sharp brightness differences or high-contrast images, such as monochrome characters and graphic patterns,
for long.
- Do not leave stationary images appearing for long, but try to refresh them at appropriate intervals of time, or try to move them using screen
saver function.
- Turn down the contrast and brightness controls.
How to clean the plasma display panel of the monitor
Before cleaning the monitor, turn off the monitor and disconnect the power plug from the power outlet.
To prevent scratching or damaging the plasma display panel face, do not knock or rub the surface with sharp or hard objects. Clean the
screen with a soft cloth moistened with warm water and dry with a soft cloth. If it is not enough, then use a cloth with mild detergent. Do not
use harsh or abrasive cleaners.
How to clean the cabinet of the monitor
Use a soft cloth to clean the cabinet and control panel of the monitor. When the plasma monitor is excessively soiled dilute a neutral detergent
in water, wet and wring out the soft cloth and afterward wipe with a dry soft cloth.
Never use acid/alkaline detergent, alcoholic detergent, abrasive cleaner, powder soap, OA cleaner, car wax, glass cleaner, etc. especially
because they would cause discoloration, scratches or cracks.
Prevention of an obstacle to Radio receivers
This monitor has been designed pursuant to the international EMI standards. This is to prevent a problem to Radio receivers.
- Keep the monitor away from Radio.
- Adjust Radio antennas in order for the monitor not to receive interference.
- The antenna cable of Radio should be kept away from the monitor.
- Use a coaxial cable for antenna.
You can check if this monitor influences Radio receivers by turning off all other equipment other than the monitor.
If you find a problem receiving Radio when using the monitor, check the instructions mentioned above.
Precautions for the cable connection
- Do ensure that all connections, (including the power plug, extension leads and interconnections between the pieces of equipment), are
properly made and in accordance with the manufacturers instructions. Switch off and withdraw the power plug before making or changing
connections.
- Confirm the connector is fixed tightly when the signal cable is connected.
Also confirm the screws on the connector are tightened.
- Plug the power cord of the monitor into a different socket from that for other equipment, such as Radio etc..
- Use a plug with ground terminal and make sure that it connects to the ground.
5
011_PDM-4210_G_EN_Caution
2003.12.24 01:09
ページ 6
(ブラック 版)
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. (continued)
Precaution during transportation
Please pay attention when you transport this monitor because it is heavy.
Furthermore, use the original carton box and its packaging materials when the monitor is transported.
Failure to transport the monitor in any carton except the original carton may result in damage to the monitor.
Save the original carton box and all packing material.
Do not physically impact the remote control.
A physical impact could cause damage or malfunction of the remote control.
• Take care not to drop the remote control.
• Do not place heavy objects on the remote control.
Avoid strong rays.
Any strong rays (such as direct sun rays or room lighting) onto the remote control sensors could invalidate the remote control.
Avoid radio interference.
Any interfering radiation could cause distorted images or noises.
• Avoid radio generator such as a mobile telephone, transceiver, etc. around the monitor.
Set the sound volume at a suitable level.
It is better to keep the volume level low and close the windows at night to protect the neighborhood environment.
Precautions for the installation
- Do not use makeshift pedestals and NEVER fix legs with wood screws - to ensure complete safety, always fit the manufacturers approved
pedestal or legs with the fixings provided according to the instructions.
- Use only with the cart, pedestal, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from tip-over.
- This product is designed to comply with the recommended safety standards for tilt and stability. Do not apply excessive pulling force to the
front, or top, of the cabinet that could cause the product to overturn resulting in product damage and/or personal injury.
- Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer.
- Only use the attachments/accessories specified by the manufacturer.
- Consult your dealer if you are in any doubt about installation, operation or safety of your equipment.
Other precautions
- Do not leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a
stand-by mode. Switch off using the switch on the equipment and show your family how to do this. Make special arrangements for infirm or
handicapped people.
- Disposal of this product may require specific instructions pertaining to your resident region.
- Never guess or take any chances with electrical equipment of any kind - it is better to be safe than sorry!
6
011_PDM-4210_G_EN_Caution
2003.12.24 01:09
ページ 7
(ブラック 版)
PRECAUTIONS
ENGLISH
• Please read this User's Manual thoroughly, especially the "CAUTION:READ THIS BEFORE OPERATING YOUR UNIT." and the "PRECAUTIONS"
sections. Mis-use may cause damage to your plasma monitor, which could shorten its lifespan, or cause injury to yourself. Should you
encounter any difficulty in the set-up or operation of your monitor, firstly refer to the Troubleshooting guide at the rear of this manual.
In the unlikely event of a problem occurring with your plasma monitor, switch off at the mains sockets, pull out the plugs, and contact your
dealer immediately.
• Under no circumstances remove the rear cover of your plasma monitor.
Never guess or take any chances with electrical equipment of any kind - it is better to be safe than sorry!
• It is prohibited for the end user of this product to copy, reverse engineer or reverse compile the software included therein, save to the extent
permitted by law.
• After the plasma monitor has been turned on for any length of time, you will notice that the screen becomes warm. Please note that this is
normal. Sometimes the screen might have some tiny bright or dark spots. Please note that this is normal.
• To prevent scratches or damages to the plasma display panel, do not knock or rub the surface with sharp or hard objects.
7
012_PDM-4210_G_ENG
2003.12.24 01:15
ページ 8
(ブラック 版)
COMPONENT NAMES
Front
Main Unit
Cabinet
(front frame)
Panel
Pedestal
Control panel
• Adjustment buttons are located
on the bottom.
• The back cover is provided with
indications to distinguish the
adjustment buttons.
Remote-control
receiver
9
Indicating lamp 13
MENU button 16
▼
▼
INPUT SELECT button
VOLUME
(OK button)
UP/DOWN
RECALL button 15
buttons 14
( SELECT button)
(
ADJUST SIZE button 15
buttons)
( SELECT button)
SUB-POWER button 13
• The main power switch is located at the back, on the
lower surface.
Main power switch 13
14
• ( ) indicates the function while the MENU is displayed on the screen.
Caution when moving the main unit
• As this product is heavy, whenever it is moved, two
people are required to transport it safely.
• Whenever the unit is moved it should be lifted forwards
using the two handgrips at the back, and the unit should
then be held at the base on both sides for stability.
Handgrips
Rear
Handgrips
Handgrips
External
speaker
terminals
External
speaker
terminals
11
11
External device connection terminals
RGB input terminals 11
8
012_PDM-4210_G_ENG
2003.12.24 01:15
ページ 9
(ブラック 版)
COMPONENT NAMES (continued)
ENGLISH
Remote control
POWER OFF button 13
13 POWER ON/OFF button
POWER ON button 13
MUTE button 14
14
VOLUME UP/DOWN buttons
VOL
RGB/VIDEO buttons 14
PinP button 34
AUTO button 16
MENU button 16
RGB 1
RGB 2
MUTE
VOL
AV1
AV2
AV3
AV4
AUTO
PinP
SIZE
RECALL
15 SIZE button
15 RECALL button
MENU
16 RETURN button
OK
OK button 16
ID
16 SELECT/ADJUST buttons
ID SET
16 ID SET button
ID button 16
Loading Batteries
1. Open the battery cover.
• Slide back and remove the battery
cover in the direction of the arrow.
Handling the Remote Control
Use the remote control within about 5 m from the front of the unit,
within a 30 degree arc either side of the remote control sensor.
2. Load the batteries.
• Load the two Size AA batteries included, matching polarity
markings on the batteries to those on
the case.
With in 30
degrees
With in 30
degrees
About 3m
About 3m
About 5m
3. Close the battery cover.
VOL
RGB 1
• Replace the battery cover in the direction of the arrow and snap
it back into place.
RGB 2
MUTE
VOL
AV1
AV2
AV3
AV4
AUTO
PinP
SIZE
RECALL
MENU
OK
ID
ID SET
CAUTION
ATTENTION
• Do not use new and old batteries together. The batteries could
explode or leak, resulting in fires, physical injury, or stains.
• When loading batteries, observe their correct polarities as
marked on the product. If loaded in the wrong direction, the
batteries could explode or leak, resulting in fires, physical injury,
or stains.
• Do not drop exert undue force on the remote control.
• To avoid possible failures. Do not splash the remote control with
water or put it on a wet object.
• It you do not intend to use the remote control for an extended
period of time, remove the batteries from it.
• If the remote control begins to lack responsiveness, replace the
batteries.
• Strong light such as direct sunlight impinging on the
photoreceptor of the remote control can cause operational
failure. Position this unit to avoid direct contact with such light.
9
012_PDM-4210_G_ENG
2003.12.24 01:15
ページ 10
(ブラック 版)
INSTALLATION INSTRUCTIONS
Installation
• When installing the monitor, use the pedestal.
The pedestal has been used for the illustrations in this manual.
CAUTION
• Use one of the special mount units to install this product. A mount of insufficient strength or inadequate
design can cause overturning or dropping and result in fire, electrical shock or injury. Please note that our
company assumes absolutely no responsibility for personal injuries or property damage caused by use of
other mount units or improper installation.
10cm (4 inches) or more*
Clamp
• Installation of the wall mount unit and ceiling mount unit can be dangerous, so do not attempt this work
yourself. Ask your dealer to provide the name of a qualified installer.
Cord
or
chain
• In order to prevent an internal temperature increase, maintain a space of 10cm (4 inches : For a desktop setup) or more between the sides and other objects such as walls, etc., so that the ventilation holes are not
blocked.(✻)
Anti-tumble measures
CAUTION
Have this unit mounted in a stable place. Take measures to prevent it from tumbling down to avoid possible physical injury.
Securing to a wall or pillar
Use a commercially available cord or chain, and a clamp to secure the set to a firm wall or pillar.
Hook
Chain
cord or chain for 42"
clamp for 42"
Wall or Pillar
Hook
Securing to desktop
1) Using wood screws (two), fasten the set to the clamping screw holes on the rear of the pedestal as shown.
2) Using commercially available wood screws, secure the set firmly in position.
Wood screw
Two places
10
012_PDM-4210_G_ENG
2003.12.24 01:15
ページ 11
(ブラック 版)
INSTALLATION INSTRUCTIONS (continued)
3
to
7
)
ENGLISH
Read CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. and PRECAUTIONS (
carefully to ensure maximum safety before proceeding to these steps:
• Choose a safe level location to install the product.
• Install the monitor to have ready access to a power socket available.
• Make sure that the power switch of this device is turned off.
Connecting to a PC
(1) Make sure that the display signal of the personal computer to be used is compatible with the specifications of this
device.
• See "Product Specifications" concerning the specifications of this device. 27
~
29
(2) Make sure that the power switch of the personal computer is turned off.
(3) Connect the signal input terminal (RGB 1 or RGB 2) on the rear panel of this device to the display signal output
terminal of the personal computer.
• Use a cable that fits the input terminal of this device and the output terminal of the personal computer.
• Depending on the type of personal computer being connected, the use of an optional conversion adapter or the adapter provided with
the personal computer may be necessary in some cases. For details, refer to the instruction manual of the personal computer or ask the
personal computer manufacturer or your local retail dealer.
Monitor rear panel
Speaker (R)
Speaker (L)
Power cable
connector
EUROPE
U.K. ONLY
Power cord
(DVI)
To signal
output
terminal
(D-sub)
3.5mm
Stereo
mini jack
(RS-232C)
For customer
installation
To signal
output
terminal
To audio
output
terminal
PC
11
012_PDM-4210_G_ENG
2003.12.24 01:15
ページ 12
(ブラック 版)
INSTALLATION INSTRUCTIONS (continued)
Power Cord Connection
Connect the power cord after completing all other connections.
EUROPE
U.K. ONLY
1
2
1
2
① Connect the power cord to this device.
➁ Connect the power cord plug to the power outlet.
(The type of plug is different from this drawing for some countries.)
CAUTION
• Use only the power cord provided.
• Do not use a power supply voltage other than that indicated (AC100-240V, 50/60Hz) as this may cause fire or electric shock.
12
012_PDM-4210_G_ENG
2003.12.24 01:15
ページ 13
(ブラック 版)
OPERATING INSTRUCTIONS
ENGLISH
Turning Power On and Off
• To turn the monitor power on, press the main power
Indicating lamp
Main power switch
switch on the monitor main unit to ON, and then press
the SUB POWER button or the ON/OFF or ON button on
the remote control.
• To turn the monitor power off, press the SUB POWER
button or the ON/OFF or OFF button on the remote
control, and then set the main power switch on the
monitor main unit to OFF.
• During normal use, the main power switch is set in the ON
position, and the monitor can then be turned ON/OFF using the
SUB POWER button or the ON/OFF button on the remote
control.
Indicating lamp
Indicating
lamp
Power status
Operating
Off
Off
When the main power switch is set
to OFF.
Off
(standby)
When the main power switch is
ON, and the OFF button on the
remote control or the SUB POWER
button on the underside of the
front of the frame is OFF.
On
When the main power switch is
ON, and the ON button on the
remote control or the SUB POWER
button on the underside of the
front of the frame is ON.
Off
(Power Save)
When the main power switch is
ON, and the ON button on the
remote control or the SUB POWER
button on the underside of the
front of the frame is ON.
However, the indicator also light orange
when the unit is in POWER SAVE mode.
Lights red
Lights green
Lights orange
SUB-POWER button
POWER OFF
button
POWER ON/OFF
button
POWER ON
button
When the indicating lamp lights in orange or the message “No Sync.
Signal”, “Power Save” or “Invalid Scan Freq.” appears on the
screen, see “Power Save Mode” or “Symptoms that Appear to be
Failures.” 22
24
ATTENTION
VOL
RGB 1
RGB 2
MUTE
VOL
AV1
AV2
AV3
AV4
AUTO
PinP
SIZE
RECALL
MENU
• Avoid repeatedly turning the monitor on and off at short
intervals. Failures might result from such operation.
• Turn off the main power switch if you do not plan to use the
monitor for an extended period of time.
• If a power failure occurs while the main unit is running, it will be
powered on upon recovery from the failure. Turn off the unit
main power switch before you leave the area in which the main
unit is located.
OK
ID
ID SET
13
012_PDM-4210_G_ENG
2003.12.24 01:15
ページ 14
(ブラック 版)
OPERATING INSTRUCTIONS (continued)
Volume Adjustment
The volume can be adjusted by pressing the VOL+ and
VOL- buttons of the remote control (or the ▲ and ▼
volume buttons of the monitor unit).
Volume setting value
▼
▼
Volume 15
VOLUME UP/DOWN
buttons
INPUT SELECT button
• When a button is pressed, the volume adjustment
status guide will be displayed.
MUTE button
• The volume will increase when the VOL+ (or ▲) button is
pressed while the guide is being displayed.
• The volume will decrease when the VOL- (or ▼) button is
pressed while the guide is being displayed.
VOL
RGB buttons
Adjustment status guide display
VOLUME
UP/DOWN buttons
RGB 1
RGB 2
MUTE
VOL
AV1
AV2
AV3
AV4
AUTO
PinP
SIZE
RECALL
Audio Mute
The audio volume can be temporarily muted by pressing
the MUTE button of the remote control.
MENU
OK
ID
ID SET
Volume setting value
Volume 15
Adjustment status guide display
(The display colour will change to magenta.)
Input Switching
• Input can be switched by pressing the RGB1, RGB2,
buttons of the remote control.
• Input can be switched in the sequence of RGB1 ➔
RGB2 by pressing the INPUT SELECT button of the
monitor.
RGB1
14
RGB2
• When a button is pressed, the volume adjustment
status guide (magenta) will be displayed.
• The volume setting can be lowered by pressing the VOL- button
while the audio is mute.
• The muting can be cancelled by pressing the VOL+ button or
MUTE button while the audio is mute.
When the MUTE button of the remote control is pressed
again, the audio will be restored and the volume display
(green) will appear.
012_PDM-4210_G_ENG
2003.12.24 01:15
ページ 15
(ブラック 版)
OPERATING INSTRUCTIONS (continued)
RGB 2
MUTE
VOL
AV1
AV2
AV3
AV4
AUTO
PinP
SIZE
RECALL
ENGLISH
RGB 1
RECALL button
MENU
OK
SIZE button
ID
ID SET
RECALL button
SIZE button
Size Switching
Each time the SIZE button of the remote control or the monitor is pressed, the screen display area will change in
sequence and the status will be displayed at the bottom of the screen.
Normal
Real*
Full
Zoom3
Zoom1
Zoom2
* Real mode gives an image of the same shape as it is displayed on a computer monitor.
This mode is only available for VGA (640 X 480) and WVGA (864 X 480).
Display area selection diagram (RGB input)
Resolution
Full display
Display
Full
Circular display
Normal
Real
Zoom1
Zoom2
Zoom3
640 X 480
(VGA)
800 X 600
(SVGA)
1024 X 768
(XGA)
1280 X 1024
(SXGA)
1600 X 1200
(UXGA)
* VGA and W-VGA
only
Processes such as compression (thinning) and expansion are performed for the above signal display. Because of this, there is a possibility that
flicker may become noticeable on Zoom (1 ~ 3) depending on the display contents. If this occurs, turning the Vertical Filter On 20 can reduce
the flicker.
Input Signal Screen Display
The input signal status can be displayed on the screen by pressing the RECALL button of the remote control or the
monitor.
• The display will go out in approximately 6 seconds.
RGB
RGB2
RGB
H : 48.4kHz
V : 60.1 Hz
Off-timer
On-timer
OFF
-- -- Min.
-- -- : -- --
Input mode
Signal mode
Input horizontal frequency
Input vertical frequency
15
012_PDM-4210_G_ENG
2003.12.24 01:15
ページ 16
(ブラック 版)
OPERATING INSTRUCTIONS (continued)
Using the Menu Screen
(On-screen display system)
VOL
AUTO button
MENU button
RGB 1
RGB 2
MUTE
VOL
AV1
AV2
AV3
AV4
AUTO
PinP
SIZE
RECALL
RETURN buttons
MENU
SELECT/ADJUST
buttons
OK
When the MENU button is pressed, the adjustment menu
screen will be displayed; from there, PC signal
adjustment and setting is possible by using the SELECT
button, ADJUST button and OK button.
• Refer to 17 settings.
21
concerning the adjustment items and the
Example: Selecting the Picture screen
ID SET
ID
ID button
OK button
ID SET button
1. Press the MENU button to display the Main Menu
screen.
Picture
MENU
Automatic Adjustment of
Screen Position and the Clock
Adjustment of the screen to a position suitable for the
PC signal and the clock adjustment can be performed
automatically by pressing the AUTO button of the remote
control.
2. Press the OK button to display the Picture Menu
screen. (Use the
and
SELECT buttons to select
other items.)
OK
CAUTION
Perform this adjustment for each input (RGB1 or RGB2) and for
each signal.
* Depending on the signal, satisfactory adjustment may not be
possible in some cases. In such cases, adjust by referring to the
Setup Menu item.
Audio
Timer
Function
Setup
Language
Select
OK Set
Picture
Contrast
Brightness
Colour
Hue
Picture Enhancement
Colour Temperature
Colour Temp.Adjust
Reset
Select
Return
:
:
:
:
:
:
+ 31
– 31
0
+ 31
Off
Normal
Reset
Exit
3. Use the
and
SELECT buttons to select the item to
be adjusted and then use the
and
ADJUST
buttons to adjust (example: Contrast).
Independent Operation of
Multiple Monitors (ID No)
Setting the ID No. of the remote control allows separate
control of up to a maximum of seven monitors.
Remote control ID No. 2 (initially ID no. 1) can be set by
pressing the ID SET button for 2 sec. or more while
holding down the ID button. The number will be
incremented (2• • • 6➔7➔1➔2) when this button pressed
continuously.
The remote control ID no. can be
checked by pressing the ID SET button
while holding down the ID button.
ID Number
Monitor
[1]
R/C
[1]
Monitor ID no.
Remote control ID no.
The ID remote control is operated by pressing the
various buttons while holding down the ID button;
Operation is possible only when the remote control and
monitor ID nos. are the same.
• The remote control can be operated normally by pressing the
various remote control buttons without holding down the ID button.
• Set the monitor using the ID No. of Function MENU. 19
16
Contrast
Next / Prev
+ 31
Adjust
Return
• Press the RETURN button to return to the previous screen.
• If there is no operation for a period of one minute, the
Adjustment Menu screen will be closed automatically.
012_PDM-4210_G_ENG
2003.12.24 01:15
ページ 17
(ブラック 版)
OPERATING INSTRUCTIONS (continued)
MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
Picture
Contrast
Brightness
Colour
Hue
Picture Enhancement
Colour Temperature
Colour Temp.Adjust
Reset
Select OK Set
OK
Picture
Contrast
Brightness
Colour
Hue
Picture Enhancement
Colour Temperature
Colour Temp.Adjust
Reset
Select OK Set
Picture
Contrast
Brightness
Colour
Hue
Picture Enhancement
Colour Temperature
Colour Temp.Adjust
Reset
Select
OK Set
+ 31
– 31
0
+ 31
Off
Normal
OK
Contrast
Next / Prev
Reset
Return
:
:
:
:
:
:
+ 31
– 31
0
+ 31
Off
Normal
Reset
Return
:
:
:
:
:
:
+ 31
– 31
0
+ 31
Off
Normal
+ 31
Adjust
Return
Colour Temperature
Next / Prev
Select
Normal
Return
OK
OK
Reset
Return
▼
▼
Selected characters
:
:
:
:
:
:
ENGLISH
PICTURE MENU
Picture
Colour Temp. Adjust
Amplitude
Red
– 63
Green
0
Blue
– 31
Cut Off
Red
+ 31
Green
0
Blue
+ 31
Reset
Select
On/Off
On
Reset
Return
Setup hint
Adjust for maximum visibility to suit the ambient brightness.
Adjust further till [+40] by pressing and holding
cursor button at
[+31]. The color for [+32] to [+40] numbers will change from white to
magenta. This special mode is better for dark scenes.
For brighter scene some parts of the picture might not be clear. We
recommend to set at [+31].
"Panel Life" in the Function Menu should be set to Normal when
Contrast setting is adjusted.
Contrast
Narrows the gap between
brightness and darkness.
Broadens the gap between
brightness and darkness.
Brightness
Black is subdued for
increased overall darkness.
Black is set off for increased
overall brightness.
Adjust to taste.
Colour
Darkens colours.
Lightens colours.
Adjust to taste.
Hue
Enhances red and weakens
green.
This is not available for adjustment when receiving PAL/SECAM signal.
Enhances green and weakens
In this case the character will be grayed out.
red.
Adjust for the most realistic skin colour.
Off
Picture Enhancement
Colour Temperature
Colour Temp. Adjustment
Amplitude
Red
Green
Blue
Cut Off
Reset
Red
Cool
Low
Normal
Middle
Warm
Off
Brighter scenes are
decreased in reddish colour.
High
Black / White
On
Sets the clarity of small details to the desired level.
Normally set to Normal.
Turn On when you wish to change colour temperature to suit user
preferences.
Brighter scenes are increased
in reddish colour.
Brighter scenes are
Brighter scenes are increased
decreased in greenish colour. in greenish colour.
Brighter scenes are
decreased in bluish colour.
Brighter scenes are increased
in bluish colour.
Adjust colour temperature to suit user preference. These settings are
Dark scenes are decreased in Dark scenes are increased in independently stored in each of the 4 Colour Temperature modes.
reddish colour.
reddish colour.
Green
Dark scenes are decreased in Dark scenes are increased in
greenish colour.
greenish colour.
Blue
Dark scenes are decreased in Dark scenes are increased in
bluish colour.
bluish colour.
(Selects the Reset mode)
The original factory settings for the items of this Menu page can be
restored by pressing the OK button.
17
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 18
(ブラック 版)
OPERATING INSTRUCTIONS (continued)
AUDIO MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
MENU
Movie
▼
▼
Selected characters
Audio Mode
OK
Audio
Audio Mode
Treble
Bass
Balance
SRS TruBass
Matrix Surround
Perfect Volume
Reset
Select
Set
Music
Speech
Favourite
:
:
:
:
:
:
:
Movie
+ 10
– 10
0L
Middle
Off
Off
Reset
Return
R
Setup hint
Movie: This selects the audio mode suitable for Movies.
Music: This selects the audio mode suitable for Music.
Speech: This selects the audio mode suitable for News, Talk show
etc.
Favourite: This mode should be adjusted to suit your preference.
Treble
Suppresses treble.
Enhances treble.
Adjust to taste.
Bass
Suppresses bass.
Enhances bass.
Adjust to taste.
Balance
Suppresses right-side sound.
Suppresses left-side sound.
Adjust to taste.
Middle
SRS TruBass takes advance of the ability of the human ear to
distinguish between two different tones. By using this ability, TruBass
gives enhanced bass sound that otherwise would not be heard.
Adjust it depending on the user’s preference.
SRS TruBass
Off
Low
High
Matrix Surround
Off
On
This features the spacious sound effects of a stadium.
Perfect Volume
Off
On
This will automatically adjust volume so each channel and input has
the same average volume level.
Reset
(Selects the Reset mode)
The original factory settings for the items of this Menu page can be
restored by pressing the OK button.
TIMER MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
Off Timer
On Timer
18
▼
Selected characters
▼
MENU
OK
--Min.
30Min.
60Min.
120Min.
90Min.
--(:--)
hours
(- - : )- minutes
Timer
Off Timer
On Timer
Select
Adjust
:
30Min.
: --:-Return
Setup hint
This function automatically sets the power to standby status when the
indicated time period has elapsed.
This automatically sets the power from standby to ON when the
indicated time period has elapsed. The settable time is 00:00~11:59.
Input the required time by
SELECT buttons on the remote
control.
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 19
(ブラック 版)
OPERATING INSTRUCTIONS (continued)
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
MENU
Screen Saver
Screen Wipe
Off
60Min.
5Min.
40Min.
This is used to reduce the panel image retention that can occur with
stationary pictures by displaying a completely white screen. Select
On (continuous operation) or 60 Min. (time limit operation) and press
the OK button. Press the MENU or RETURN button on the remote
control to return to normal viewing.
This turns the gray sidebars On/Off when watching normal mode
screen size area. It is always set to Off when the monitor is powered
On. It is recommended to set Black Side Panel to off to reduce the
panel image retention.
On
Video Power Save
Optional (grayed out)
Freeze Mode
Optional (grayed out)
Default Zoom
Optional (grayed out)
Reset
(Selects the Reset mode)
Normal
Extend 1
Off
Mode Display
Inverse
1
Standby White
Gamma
Extend 2
3
6
The original factory settings for the items of this Menu page can be
restored by pressing the OK button.
This function suppresses the contrast of the screen regardless of the
Contrast setting in the Picture Menu. By this control, power
consumption can be reduced or degradation of a panel can be
mitigated. The order of power consumption is Extend 2 < Extend 1 <
Normal.
If the Contrast setting is changed when this item is set to Extend 1 or
2, it will be changed to Normal automatically.
This functions displays the Input Signal Screen Display every time the
input mode and signal mode are changed.
Set to OFF if the Input Signal Screen Display is not needed when
switching signals.
On
2
7
4
5
On
Off
Normal
Off
1
On 60Min.
Off
2.2
Reset
Return
This moves the picture around the screen in small amounts, at set
intervals, to reduce the panel image retention. Image retention
occurs when stationary objects, such as screen logos, leave a slight
image visible after they should have disappeared.
60Min.
Off
ID Number
Function
Panel Life
Mode Display
ID Number
Inverse
Standby White
Gamma
Reset
Select
Set
Setup hint
10Min.
20Min.
On
Black Side Panel
Panel Life
Off
On 60Min.
Off
Off
Split
Panoramic
Reset
Return
▼
▼
Selected characters
OK
Function
Screen Saver
Screen Wipe
Black Side Panel
Video Power Save
Freeze Mode
Default Zoom
Reset
Select
Set
ENGLISH
FUNCTION MENU
60Min.
Assigns ID nos. to the monitors so that they can be controlled
individually (up to 7 monitors can be controlled).
This function changes each level of RGB signal invert to reduce the
panel image retention. When this function is required, select On
(continuous operation) or 60Min. (time limit operation) and press the
OK button. And press the Menu or Return button to exit.
15Min.
30Min.
120Min.
60Min.
This function is also provided to prevent image retention. If time is set
for this item, the screen changes into a white pattern when the
monitor enters power save mode, and continues for the period of
setting time.
2.2
Normally set to 2.2.
2.8
19
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 20
(ブラック 版)
OPERATING INSTRUCTIONS (continued)
SETUP MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
MENU
Setup
Auto Adjust
Horizontal Position
Vertical Position
Horizontal Clock
Clock Phase
Reset
Select
Return
OK
Adjust
0
+ 31
– 20
10
Reset
Exit
OK
Horizontal Position
Next / Prev
Adjust
Setup
Auto Adjust
Horizontal Position
Vertical Position
Horizontal Clock
Clock Phase
Reset
Select
Return
Adjust
0
+ 31
– 20
10
Reset
Exit
(Menu)
Auto Adjust*
Horizontal Position
Vertical Position
Horizontal Clock
Clock Phase
Moves the horizontal position
to left.
Moves down the vertical
position.
Setup hint
(Adjust)
Press the OK button to start
automatic regulation.
Moves the horizontal position
to right.
Horizontal Position, Vertical Position, Horizontal Clock and Clock
Phase are adjusted automatically.
Adjust the left-side display position.
(This function is only for RGB2. It is not available (grayed out) for
RGB1.)
Reduces the dot clock
frequency (shrinks the right
side).
Increases the dot clock
frequency (expands the right
side).
Slows the dot clock phase
(shifts slightly to left).
Advances the dot clock phase
Adjust for clear character visibility.
(shifts slightly to right).
(This function is only for RGB2. It is not available (grayed out) for
RGB1.)
(Selects the Reset mode)
0.7V
1.0V
Adjust for maximum character clarity.
(This function is only for RGB2. It is not available (grayed out) for
RGB1.)
The original factory settings for the items of this Menu page can be
restored by pressing the OK button. (This is effective only for RGB2.)
Normally set to 0.7 V. If white is found to spread across the screen, set
to 1.0 V. (This is effective only for RGB2.)
Frequency Display
Off
On
Set this to Off if the frequency information of the Input Signal Screen
Display is not required.
WVGA Type
Off
On
This is only available for W-VGA signal.
When it is set to On, the display area modecan be selected Full or
Real.
Vertical Filter
Off
On
Turn On when concerned about screen flicker.
Frequency Mode
Movie
PC
Set to Movie when viewing moving images on a personal computer.
RGB1
Optional (grayed out)
RGB2
Optional (grayed out)
* Depending on the type of signal displayed, displays may not be optimized through automatic adjustment. Adjust manually to optimize them.
20
Return
Moves up the vertical position. Adjust the vertical display position.
(This function is only for RGB2. It is not available (grayed out) for
RGB1.)
Reset
Input Level
10
Adjust
0.7V
Off
Off
On
Movie
DVI-PC
RGB
Return
▼
▼
Selected characters
Return
OK
Clock Phase
Next / Prev
Setup
Input Level
Frequency Display
WVGA Type
Vertical Filter
Frequency Mode
RGB1
RGB2
Select
Set
0
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 21
(ブラック 版)
OPERATING INSTRUCTIONS (continued)
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
MENU
ENGLISH
LANGUAGE MENU
Language
English
Français
Deutsch
Español
Italiano
Norsk
Svenska
OK
Select
Return
Exit
Select a language using the ▼ ▲ SELECT buttons and press the OK button.
OTHER FEATURES
Automatic Store
Approximately 1 sec. after adjustment is completed, the adjustments will be recorded as shown in the table below.
Menu
Picture
Display
Registration condition
For every input function, 1 setting
is registered.
Contrast
Menu
Function
Registration condition
1 setting is registered.
Screen Wipe
(not registered)
Colour
Black Side Panel
Hue
Panel Life
(not registered)
1 setting is registered.
Picture Enhancement
Mode Display
Colour temperature
ID Number
Brightness
Inverse
Colour Temp. Adjust
R Amplitude For every Colour Temperature, 1
setting is registered.
G Amplitude
Standby White
Gamma
Setup
B Amplitude
R Cut Off
Vertical Position
(not registered)
For every signal Mode, 1 setting is
registered. (Only for RGB2)
Horizontal Clock
B Cut Off
Clock Phase
Audio Mode
1 setting is registered.
Treble
Bass
For every Audio Mode, 1 setting is
registered.
Balance
1 setting is registered.
Input Level
For every Audio Mode, 1 setting is
registered.
1 setting is registered.
Frequency Display
WVGA Type
Vertical Filter
SRS TruBass
Matrix Surround
Auto Adjust
Horizontal Position
G Cut Off
Audio
Display
Screen Saver
Frequency Mode
Language
1 setting is registered.
Perfect Volume
• The previously recorded items will be lost.
• The signal mode can be identified by the horizontal/vertical sync
frequency and the sync signal polarity. Different signals for which
all the elements are the same or similar will be handled as the
same signal.
21
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 22
(ブラック 版)
OTHER FEATURES (continued)
Signal Check
Changes in the signal status are displayed on the screen as they arise.
Status
Display
When Mode Display is set to ON,
the input signal is switched or
when the RECALL button is
pressed.
RGB
Action
A guide is displayed for the input
terminal and the horizontal and
vertical sync frequency.
RGB2
RGB
H : 48.4kHz
V : 60.1 Hz
OFF
When the sync signal is no longer
detected.
When the input signal does not
match the monitor specifications
or is in an unstable state.
• A guide displays No Sync.
Signal, and Power Save (for
approx. 5 sec.)
• When the condition continues
and the sync signal cannot be
detected, the indicator lamp of
the power source changes in
orange and the mode switches
to power save mode.
Recheck the personal computer
power switch status and the
connection status.
"Invalid Scan Freq" appears on
the display panel.
Recheck the input signal
specifications.
-- -- Min.
-- -- : -- --
! No Sync. Signal
27
~
29
! Invalid Scan Freq.
Power Save Mode
When the RGB, RGB2 input is selected
• When this unit is connected to a VESA DPMS computer, the Power Save (Off) mode can be set to be activated automatically when the
computer is not being used to reduce power consumption by this unit.
RGB sync signal
Horizontal
Yes
No
Yes
No
Vertical
Yes
Yes
No
No
PC signal
Active (normal display)
Blank (no display)
Operation mode
On
Off
Indicating lamp
Lights green
Lights orange
Power consumption
365W (42")
3W or less (RGB1)
1W or less (RGB2 ; 100V<AC<120V)
3W or less (RGB2 ; 120V<AC<240V)
Returning to operating status
• Operate the personal computer, or press either the INPUT SELECT button of the main unit or the RGB1/RGB2 buttons of the remote control to
return the unit to power on mode.
22
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 23
(ブラック 版)
IMAGE RETENTION OF PLASMA DISPLAY PANEL
ENGLISH
There are different characteristics that result in panel image retention depending on how the plasma monitor is used.
Situations and effective usage methods related to ghosting are provided below.
Image retention characteristics of a plasma display panel
The image retention phenomenon of a plasma display panel occurs due to partial phosphor degradation arising from partial character and
figure display.
For example, when the character image as shown in Fig. A at the right is
continuously displayed for a long period of time, the only part of the phosphor
(Red,Green, Blue) that will degrade will be the colour of the applicable character
display portion. Consequently, when a white image is displayed on the entire
screen as shown in Fig. a, the character marks displayed up to that time will
become a colour difference visible to the eye, but the phosphor will never burn.
[Fig. A]
[Fig. a]
■The degree of image retention is proportional to the brightness of the characters and figures displayed as well as the display time.
• The tendency of the phosphor is to degrade more the brighter the characters
and figures are displayed. When images of figures with different levels of
brightness, as shown in Fig. B, are continuously displayed for a long period of
time, it becomes easier for image marks at locations when the brighter figures
are displayed to be noticeable.
[Fig. B]
[Fig. b]
✻ The image retention images in this document are exaggerated for the purpose of explanation. The actual manner in which the image retention
is seen differs depending on the operation time and brightness.
Methods to Reduce the Occurrence of Image Retention
• Lower the Contrast and Brightness settings of the plasma display panel as much as possible.
A function is provided in the display that allows you to control the brightness of the screen to reduce degradation of the panel. Using this
function makes it possible to reduce image retention.
(Refer to Panel Life (Extend 1.or Extend 2 shown on 19 )
• Set the plasma monitor to an “Screen Wipe” or “Inverse” display.
The occurrence of image retention when displaying images of identical patterns, such as static images, for long periods of time can be
reduced by displaying a reversed colour or completely white screen for about 1 ~ 2 hours after terminating the display.
(Settings can be made using Screen Wipe and Inverse of Function MENU shown on 19 )
• Using in combination with moving images
Since the degradation of the fluorescent material progresses comparatively uniformly for moving images, the occurrence of partial image
retention can be controlled. We recommend using the plasma monitor in combination with moving images such as those of DVD.
* Please be careful since image retention will occur if display is left in a two screen display state for a long period of time.
* Television broadcasts include images displayed for long periods of time in which the left and right or top and bottom of the image are cut
and broadcast station name or time are displayed for a long period of time at the same portion of the screen. Image retention in these
portions can be expected to occur, so please be aware.
NOTES
About screen defects
• High precision technology is used in the making of plasma display panel but there may be dark spots (points that do not illuminate) and bright
spots (points that are too bright) in some cases. These do not indicate a malfunction.
About residual images
• In some cases, residual images may remain after the short-term display of still images and another image is displayed, but these will
disappear and return to normalcy. This is not a malfunction.
About the panel screen
• Plasma display panels display images by means of electrical discharges inside the panel. Because of this, the temperature of the panel
surface may rise in some cases.Also, plasma display panels are made of finely processed glass. A reinforced glass filter is installed over the
panel surface but avoid strong impact because there is still danger of glass breakage.
23
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 24
(ブラック 版)
TROUBLESHOOTING
Symptoms That Appear to be Failures
Make the checks suggested below depending on the symptoms observed. If the symptoms remain uncorrected, contact your dealer.
CAUTION
Customer servicing can be hazardous.
Symptom
Point to check
• No picture with the power-indicating lamp
off.
• Check the way the power cable is connected.
• Press the power switch.
• The message “No Sync. Signal” or “Power
Save” is displayed.
No sync signal is detected.
• Check the way the signal cable is connected.
• Make sure that the switch of the computer, imaging equipment ,
etc., is turned on.
• Make sure the computer is not in the power-save mode.
• Check to see if the input selection matches the connection
terminal.
! No Sync. Signal
• No picture, with the power indicating lamp lit
orange.
• The message “Invalid Scan Freq.” is
displayed.
! Invalid Scan Freq.
An input signal is not received normally.
• Check to see if the input signal matches the monitor
specifications.
• Check the way the signal cable is connected.
See page
12
13
11
11
28
29
• The power indicating lamp is lit normally but
no picture displays.
24
• Check the contrast and brightness settings (adjust them for
higher contrast and brightness).
• Check the way the signal cable is connected.
• The display image appears flowing
slantwise.
• Text displayed across the screen appears
vertically streaked, with the characters in
vertical columns blurred.
• Adjust the dot clock frequency and phase. (Adjust the dot clock
frequency first, the dot clock phase next.)
(RGB input)
• Text displayed across the screen appears
blurred.
• A fine pattern flickers when displayed on the
screen.
• Adjust the dot clock phase for the clearest viewing.
(RGB input)
• The remote control does not work.
• Check to see if the batteries are loaded in the remote control in
opposite direction.
• Check to see if the batteries in the remote control are OK.
• Check if the setting of remote control ID no. is correct.
17
11
20
26
20
26
9
16
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 25
(ブラック 版)
TROUBLESHOOTING (continued)
Symptom
• The temperature of the display panel surface is high.
Point to check
See page
• Plasma display panel is lighting the phosphors in the display panel
by the discharge of internal radiation. In some cases, this may
cause the temperature of the panel surface to increase. Please
note that this is not a malfunction.
-
• There are points (*) on the screen that differ in colour from
the periphery of the screen.
*Points that do not light, points with brightness different
from that of the periphery, points with color different from
that of the periphery, etc.
• High-precision technology is used to manufacture the plasma
display panel, However in some cases, there are minor defects in
some parts of the screen. Please note that this is not a
malfunction.
• Vertical stripes appear, depending on the screen contents.
• The plasma display panel is lighting the phosphors by the
discharge of internal radiation. Depending on the screen contents,
in rare cases this may cause vertical stripes to appear because of
failure to light. Please note that this is not a malfunction.
• Coarse horizontal stripes appear in FULL display.
ENGLISH
Symptoms That Appear to be Failures (continued)
-
-
• Adjusting the Clock Phase will reduce the horizontal stripes.
(RGB input)
20
• Flickering in the form of horizontal lines oscillating up and
down.
(PC INPUT MODE only)
• If the direct frequency from the computer is below 85Hz, try a
higher frequency (upper limit 85Hz). There may be a slight
attenuation of the current image.
• Try turning the Vertical Filter On. For this case however, the
vertical resolution will drop.
20
• The fan motor is noisy. (Fan application model only)
• Use the fan that controls the temperature in the main body to lower
the temperature of this unit. If the ambient air temperature
increases, the fan will start, the RPMs will increase and motor
noise will grow louder. This is not a malfunction though.
-
• The top of the monitor heats up.
• When used for long periods of time, the top of the monitor may
heat up. This is not a malfunction.
-
• Text characters are displayed with varying thicknesses.
• The thicknesses of characters and lines may vary if images with a
vertical resolution greater than 512 lines are displayed; however,
this is not a malfunction.
-
25
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 26
(ブラック 版)
TROUBLESHOOTING (continued)
Actions to Correct Abnormal Displays (continued)
Depending on the kind of system equipment used, images may not be displayed normally. In this case, make the
adjustments suggested below. (only for RGB2)
Symptom 1
Text displayed across the screen appears vertically streaked, with some characters blurred (figure 1).
The display image appears flowing (figure 2) (RGB input).
Vertical
streaks
Figure 1
Before adjustment
Some characters
are blurred.
ABCDEFGHIJ
abcdefgABCDEFGabcd
ABCDEFGHIJ
abcdefgABCDEFGabcd
Example
ABC
B
ABC
After adjustment
All characters appear
crisp now.
ABC
ABC
After adjustment
All characters are
blurred.
1) Press the AUTO button on the remote control.
Adjustment
procedure
When adjustment is not possible with Auto Adjust
2) Press the MENU button. The Main Menu will be displayed.
3) Press the
SELECT button and select Setup.
4) Press the OK button. The Setup Menu will be displayed.
5) Press the
SELECT button and select Horizontal Clock.
(Display fine patterns as characters or a vertical striped pattern over the entire screen during Horizontal Clock adjustment.)
6) Press the
or
ADJUST buttons and search for clear characters over the entire screen.
7) Perform adjustment for symptom 2 below, when the characters are blurred on the entire screen.
• The display image may be momentarily disturbed during clock adjustment but this is not a failure.
Symptom 2
Text displayed across the screen appears blurred in its entirety (figure 2).
A fine pattern flickers when displayed on the screen (figure 3).
Before adjustment
Figure 2
ABCDEFGHIJ
abcdefgABCDEFGabcd
ABCDEFGHIJ
abcdefgABCDEFGabcd
Figure 3
Before adjustment
ABC
ABC
Example
After adjustment
After adjustment
ABC
1) Press the AUTO button on the remote control.
Adjustment
procedure
When adjustment is not possible with Auto Adjust
2) Press the MENU button. The Main Menu will be displayed.
3) Press the
SELECT button and select Setup.
4) Press the OK button. The Setup Menu will be displayed.
5) Press the
SELECT button and select Clock Phase.
(Display fine patterns as characters or a vertical striped pattern over the entire screen during Clock Phase adjustment.)
6) Press
or
ADJUST buttons to make the text appear
clean across the screen.
26
6) Press
or
ADJUST buttons to make the text appear
without flickering.
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 27
(ブラック 版)
PRODUCT SPECIFICATIONS
Product specifications and designs are subject to change without notice.
Display
dimensions
Approx. 42 inches (922 (H) x 522 (V) mm, diagonal 1059mm)
Resolution
1024 (H) x 1024 (V) pixels
Net dimensions
(excluding pedestal)
1030 (W) x 636 (H) x 91 (D) mm
Net weight
(excluding pedestal)
34.9kg
Ambient
conditions
ENGLISH
Panel
Temperature
Operating : 5˚C to 35˚C, Storage : 0˚C to 40˚C
Relative humidity
Operating : 20% to 80%, Storage : 20% to 90% (non-condensing)
Power supply
AC100 - 240V, 50/60Hz
Power consumption/at standby
365W / <3W
Audio output
12W + 12W (6Ω)
(RGB input)
Input signals
Input terminals
RGB1 DVI input terminal (DVI-D)
RGB1 audio input terminal (3.5mm Stereo Mini Jack)
RGB2 analog RGB input terminal (D-sub 15-pin)
RGB2 audio input terminal (3.5mm Stereo Mini Jack)
Video signals
0.7 V/1.0 Vp-p, analog RGB (Recommended Signal)
Sync signals
H/V separate, TTL level [2KΩ]
H/V composite, TTL level [2KΩ]
Sync on green, 0.3 Vp-p [75Ω]
43 modes 28
Recommended signal
29
• The monitor takes at least 30 minutes to attain optimal picture quality.
Signal Input
RGB terminal (D-sub 15-pin connector)
Pin
Input signal
1
R
2
G or sync on green
3
B
4
No connection
5
No connection
5
15
4
3
2
1
10
9
8
7
14
13
12
6
11
• When different kinds of input signals are simultaneously input to
the monitor via a graphics board or the like, the monitor will
automatically select the signals in the following priority order:
6
R.GND
7
G.GND
Sync signal type
Priority
B.GND
H/V separate sync.
1
H/V composite sync.
2
sync.on Green *
3
8
9
No connection
10
GND
11
No connection
12
[SDA]
13
H. sync or H/V composite sync
14
V.sync. [V.CLK]
15
[SCL]
*Even in the case of the recommended signals shown on the
following page, there may be instances when correct display is not
possible. In this case, use H/V separate sync, H/V composite sync.
27
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 28
(ブラック 版)
PRODUCT SPECIFICATIONS (continued)
Signal Input (continued)
DVI terminal (DVI-D)
Pin
Input signal
Pin
1
2
3
4
5
6
7
8
9
10
T.M.D.S. Data2T.M.D.S. Data2+
T.M.D.S. Data2/4 Shield
T.M.D.S. Data4T.M.D.S. Data4+
DDC Clock
DDC Data
No Connect
T.M.D.S. Data1T.M.D.S. Data1+
14
15
16
17
18
19
20
21
22
23
+5V Power
Ground (for+5V)
Hot Plug Detect
T.M.D.S. Data0T.M.D.S. Data0+
T.M.D.S. Data0/5 Shield
T.M.D.S. Data5T.M.D.S. Data5+
T.M.D.S. Clock Shield
T.M.D.S. Clock+
Input signal
11
T.M.D.S. Data1/3 Shield
24
T.M.D.S. Clock-
12
T.M.D.S. Data3-
13
T.M.D.S. Data3+
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
Frame GND
Recommended Signal List
With Digital RGB signal input (RGB1 input)
Signalmodus
Horizontal frequency
(kHz)
Dot clock frequency
(MHz)
70.08
31.47
25.18
59.94
31.47
25.18
864 X 480
59.94
31.47
34.24
4
640 X 480
72.81
37.86
31.50
5
640 X 480
75.00
37.50
31.50
6
640 X 480
85.01
43.27
36.00
7
800 X 600
56.25
35.16
36.00
8
800 X 600
60.32
37.88
40.00
No.
1
2
3
9
Signal Name
VGA
W-VGA
VESA
Resolution
Vertical frequency
(Hz)
640 X 400
640 X 480
800 X 600
72.19
48.08
50.00
10
800 X 600
75.00
46.88
49.50
11
800 X 600
85.06
53.67
56.25
12
1024 X 768
60.00
48.36
65.00
13
1024 X 768
70.07
56.48
75.00
14
1024 X 768
75.03
60.02
78.75
• Make sure that the signal of the equipment to be connected is compatible with the specifications on this list.
28
Remarks
WVGA type : On
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 29
(ブラック 版)
PRODUCT SPECIFICATIONS (continued)
ENGLISH
Recommended Signal List (continued)
With Analog RGB signal input (RGB2 input)
No.
Signal Name
Signal mode
Vertical frequency
Resolution
(Hz)
Horizontal frequency
(kHz)
Dot clock frequency
(MHz)
1
2
VGA
640 X 400
640 X 480
70.08
59.94
31.47
31.47
25.18
25.18
3
W-VGA
864 X 480
59.94
31.47
34.24
640 X 480
640 X 480
640 X 480
800 X 600
800 X 600
800 X 600
800 X 600
800 X 600
1024 X 768
1024 X 768
1024 X 768
1024 X 768
1152 X 864
1280 X 1024
1280 X 1024
1280 X 1024
1600 X 1200
1600 X 1200
1600 X 1200
640 X 480
832 X 624
1024 X 768
1152 X 870
1280 X 768
72.81
75.00
85.01
56.25
60.32
72.19
75.00
85.06
60.00
70.07
75.03
85.00
75.00
60.02
75.03
85.02
60.00
75.00
85.00
66.67
74.55
74.93
75.06
59.833
37.86
37.50
43.27
35.16
37.88
48.08
46.88
53.67
48.36
56.48
60.02
68.68
67.50
63.98
79.98
91.15
75.00
93.75
106.25
35.00
49.72
60.24
68.68
47.986
31.50
31.50
36.00
36.00
40.00
50.00
49.50
56.25
65.00
75.00
78.75
94.50
108.00
108.00
135.00
157.50
162.00
202.50
229.50
30.24
57.28
80.00
100.00
81.00
1280 X 768
69.997
56.137
94.760
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
VESA
Macintosh
W-XGA
Remarks
WVGA type:On
• The type of video board or connecting cable used may not allow for correct display adjustment of Horizontal Position, Vertical Position, Horizontal
Clock and Clock Phase.
• The monitor may fail to display an animation image correctly when a signal having a vertical frequency of 85Hz or higher is input to it.
• The monitor differentiates signal modes according to the horizontal and vertical frequencies and the horizontal and vertical sync signal
polarities. Note that different signals having all these elements alike may be handled as the same signal.
• Displaying images with more than 512 lines of vertical resolution at Full diplay (compressed display) can result in the interpolation of stripes.
29
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 30
(ブラック 版)
SUPPLEMENT
30
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 31
(ブラック 版)
Optional Video Unit Function
Additional functions when the optional video unit is installed are as follows: ( 31
~
42
)
ENGLISH
INSTALLATION INSTRUCTIONS
Connecting to a Video Imaging Device
(1) Make sure that the power switch of the monitor is turned off.
(2) Make sure that the power switch of the imaging device is turned off.
(3) Use a commercially available cable and connector to connect the signal input terminal on the rear panel of this
device and the signal output terminal of the imaging device.
Speaker (R)
EUROPE
U.K. ONLY
Power
cord
To composite
input terminal
To audio input
terminals
20
18
16
14
12
10
21 19
17
15
13
11
9
8
7
6
5
4
3
Speaker (L)
Monitor rear panel
DVD player
2
DVD player
1
VCR
To SCART
terminals
To audio output
terminals
To component
output terminals
To component
input terminals
Set-Top Box
To S video output
terminal
To composite
output terminal
To audio output
terminals
To SCART
terminal
To RGB,
video and audio
input terminals
[An example of connecting video imaging devices]
Use if the
video
equipment
has an
S video
input terminal
VCR
DVI-STB and RGB component setup
• If video equipment with an S video output terminal is used,
connection with S video cable is recommended to provide finer
video quality. (If the S video input terminal and the video input
terminal of AV3 connect to the monitor at the same time, S video
input would govern.)
• If the OUTPUT (MONITOR) terminal is connected to an external
monitor with a 75 Ohm terminal, it is possible to view the same
image as on the main unit. But it is possible to monitor only the
composite video signal from AV1, AV2, AV3, or AV4 input that is
displayed on the screen at the time.
To component video
equipment.
Please use connection
cable suitable for the terminal
form of video equipment.
Applicable video signals for each input terminal (See PRODUCT SPECIFICATIONS for details.
Terminal
Signal
RCA/SCART
CVBS
S-video
Component
DVI
RGB
PC
D-sub
STB
RGB
40
)
Remarks
Component
AV1
AV2
Refer to Setup Menu. 38
AV3
AV4
Refer to Setup Menu. 38
RGB1
Refer to Setup Menu. 39
RGB2
Refer to Setup Menu. 39
(
: Available)
31
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 32
(ブラック 版)
OPERATING INSTRUCTIONS
VOL
RGB/VIDEO
buttons
RGB 1
RGB 2
MUTE
VOL
AV1
AV2
AV3
AV4
AUTO
PinP
SIZE
RECALL
SIZE button
MENU
INPUT SELECT button
OK
SIZE button
Input Switching
• Input can be switched by pressing the AV1, AV2, AV3,
AV4, RGB1 or RGB2 buttons of the remote control.
• Input can be switched in the sequence of AV1➔AV2 ➔
AV1
AV3 ➔ AV4 ➔ RGB1 ➔ RGB2 by pressing the INPUT
SELECT button of the monitor.
AV2
RGB2
AV3
RGB1
AV4
Size Switching
Each time the SIZE button of the remote control or the
monitor is pressed, the screen display size will change
in sequence and the status will be displayed at the
bottom of the screen.
• During VIDEO signal input (AV1, AV2, AV3)
Panoramic
14:9Zoom
4:3
• During AV4 signal input
Full
C14:9L
Auto
Zoom
14:9Zoom
• The size will be fixed Full mode and not change when receiving
the component signal of 1080i/50, 1080i/60 or 720p/60.
Full
Zoom
C14:9L
• [Auto] is the mode using the Switch signal from the equipment
connected to AV4 terminal included in SCART connector No.8 pin
which indicate the picture format of the video source. When
Switch signal has not been detected, Default Zoom setting in the
Function Menu is used to choose.
• And during some input mode except AV4, if the Switch signal is
detected under the condition that [Auto] is selected for the
picture size of AV4, the input mode will automatically transfer to
AV4.
Full
Display size selection diagram
When you want to
Play a 4:3 image in a 16:9 screen.
Play a 4:3 image in a 16:9 screen with the
height and width of the middle of the
screen enlarged on equal scales and with
both sides appearing somewhat enlarged.
Set the display size to
4:3
Panoramic
Play a 16:9 VISTA size image from a 4:3
image faithfully reproduced on the 16:9
screen.
Zoom
Play a 4:3 image faithfully from a 16:9
screen in the standard vertical size and
horizontally squeezed.*
Full
Play a 14:9 image in a 16:9 screen
expanded vertically and squeezed
horizontally.
Play a 14:9 image expanded vertically on
the 16:9 screen.
Input signal
Remarks
Blanking occurs on both sides.
(4:3 signal)
(Vista)
• The 4:3 image is called a letterbox image.
• In some cases, some slight blanking may
remain at the top and bottom.
(Squeeze)
* An image with an aspect ratio of 16:9
shrunk horizontally to 4:3 to display in a 4:3
screen
This mode is provided for the broadcasting
program with WSS code-C14:9L.
C14 : 9L
(14:9 signal)
This mode is provided for the broadcasting
program with WSS code-14:9Zoom.
14 : 9Zoom
(14:9 signal)
32
Display screen
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 33
(ブラック 版)
Position + 31
Press
ENGLISH
Vertical picture position can be adjusted for [Panoramic], [Zoom] , [C14:9L] and [14:9Zoom] mode as follows.
1. Press the SIZE button and
SELECT buttons during picture size display.
2. The position display will appear.
3. The adjustment range of each picture size is as shown below.
[Panoramic]
- 12 to + 12
[Zoom]
- 31 to + 31
[C14:9L] and [14:9Zoom]
- 16 to + 16
4. When 1080i/50 or 1080i/60 component signal is received, vertical position can be adjusted only one step up. (The range: 0 to +1)
Position - 31
Press
ATTENTION
Using a wide-screen monitor
• This monitor has a screen mode selection feature. If an incompatible screen mode is selected to play certain software, such as a TV
program, the image will appear different from the original. Take this into consideration when making screen mode choices.
• Use of this monitor in its enlarged display mode with the wide feature enabled in coffee shops, hotels and other establishments for
commercial or pubic viewing purposes could infringe on the copyright holder’s rights protected by Copyright Law.
• When a normal 4:3 image is displayed over the entire screen in the Panoramic mode, parts of the periphery of the image may disappear
and/or appear distorted in some cases. Use the 4:3 mode to view images which were created in 4:3 mode.
This mode allows 4:3 content to be viewed without picture distortion.
33
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 34
(ブラック 版)
OPERATING INSTRUCTIONS (continued)
Displaying MULTI PICTURE
If the PinP button on the remote control is pressed
MULTI PICTURE will display.
Activating the P-in-P mode from the RGB input screen
Pressing the PinP button once will display 2 pictures.
RECALL button
VOL
PinP button
RGB 1
RGB 2
MUTE
VOL
AV1
AV2
AV3
AV4
AUTO
PinP
SIZE
RECALL
RECALL button
• This mode can be available from RGB1(DVI-PC) and RGB2(RGB)
input.
• The speaker icon can be shifted left and right by pressing the
and
SELECT buttons; the audio of the video will be output from
the side on which the speaker icon
RGB2
is located.
AV1
• The sub-screen position can be
selected up and down by pressing
SELECT buttons.
• When the speaker icon appears on
(Subthe left of the subscreen, as in the
screen)
illustration at right, you can use the
AV1, AV2, AV3 or AV4 buttons to
select the subscreen input mode.
• Pressing the PinP button or the RETURN button will cancel the 2
pictures display.
• "Frequency Mode" in the Setup Menu should be set to Movie when
sub-screen is the component signal of 1080i/50 or 1080i/60.
AV1: Displays the VIDEO input signal of the sub-screen.
Activating the Split mode from the video input screen
MENU
OK
ID
RETURN button
Main
Sub
RGB1
PAL, SECAM
NTSC3.58/4.43
576i, 576p
480i, 480p
1080i/50
1080i/60
720p/60
STB
RGB2
Component
AV1
~AV4
AV1
AV2
AV1~AV4
PAL
NTSC3.58
SECAM NTSC4.43
AV1
AV2
• The speaker icon can be shifted left
and right by pressing the and
SELECT buttons; the audio of the
video will be output from the side on
which the speaker icon is located.
• The same video input mode cannot
be selected for both screens at the same time.
• Pressing the PinP button again or the RETURN button will cancel
the 2 pictures display.
• When the Video input is set to RGB Video, this Split mode is not possible.
• Refer to the table for 2 pictures (Split) mode.
ID SET
2 Pictures (Split)
Input terminal
Pressing the PinP button one
time will display 2 pictures.
576i
576p
AV1, AV2
RGB1
RGB2
480i
1080i/50 1080i/60 720p/60 STB Component
480p
(
Main
Sub
: Available)
NOTE
• Even if the input of the horizontal / vertical synchronizing signal (or video signal) stops in the MULTI PICTURE display, the mode will not
change to power save mode.
• Please be careful since image retention will occur if the plasma monitor is left in a MULTI PICTURE display state for a long period of time.
Input Signal Screen Display
The input signal status can be displayed on the screen
by pressing the RECALL button of the remote control or
the monitor.
• The display will go out in approximately 6 seconds.
34
VIDEO
Off-timer
On-timer
AV1
Composite
OFF
-- -- Min.
-- -- : -- --
Input mode
Signal mode
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 35
(ブラック 版)
OPERATING INSTRUCTIONS (continued)
MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
OK
Picture
Picture Mode
Contrast
Brightness
Colour
Sharpness
Hue
Colour Temperature
Contrast Mode
Reset
Select OK Set
Dynamic
+31
-31
0
+15
0
Normal
Normal
Reset
Return
Picture
Picture Mode
Contrast
Brightness
Colour
Sharpness
Hue
Colour Temperature
Contrast Mode
Reset
Select OK Set
Dynamic
+31
-31
0
+15
0
Normal
Normal
Reset
Return
Picture
YNR
CNR
Film Mode
PAL Comb Filter
LTI
CTI
Black Enhancement
Auto Colour
Reset
Select OK Set
Dynamic
Off
Off
On
On
Off
Off
Off
Off
Reset
Return
Picture
YNR
CNR
Film Mode
PAL Comb Filter
LTI
CTI
Black Enhancement
Auto Colour
Reset
Select OK Set
Dynamic
Off
Off
On
On
Off
Off
Off
Off
Reset
Return
Picture
Colour Temp. Adjust
Colour Management
Colour Decoding
Select OK Set
Dynamic
Picture
Colour Temp. Adjust
Colour Management
Colour Decoding
Select OK Set
ENGLISH
PICTURE MENU
OK
Picture Mode
Next/Prev
Select
Dynamic
Return
Contrast Mode
Next/Prev
Select
Normal
Return
YNR
Next/Prev
Select
Off
Return
Auto Colour
Next/Prev
On/Off
OK
OK
OK
OK
Return
Dynamic
OK
Picture
Colour Temp. Adjust
Amplitude
Red
– 63
Green
0
Blue
– 31
Cut Off
Red
+ 31
Green
0
Blue
+ 31
Reset
Select
On/Off
Magenta
Red
Yellow
Green
Cyan
Blue
Return
Dynamic
OK
Return
Return
On
Reset
Return
Picture
Colour Management
Reset
Select
Picture
Colour Temp. Adjust
Colour Management
Colour Decoding
Select OK Set
Off
On
+ 60
+ 30
0
+ 60
+ 30
0
Reset
Return
On/Off
Picture
Colour Decoding
RGB
Red
Green
Colour
Hue
R
G
Reset
Select
B
0
+ 60
0
+ 31
Reset
Return
Exit
35
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 36
(ブラック 版)
OPERATING INSTRUCTIONS (continued)
PICTURE MENU (continued)
▼
▼
Selected characters
Dynamic
Picture Mode
Natural
Adjust for maximum visibility to suit the ambient brightness.
This can be adjusted further till [+40] by pressing and holding
cursor button at [+31]. The color for [+32] to [+40] numbers will change
from white to magenta. This special mode is better for dark scenes.
For normal viewing we recommend that the Contrast is set to [+31].
"Panel Life" in the Function Menu should be set to Normal when this
Contrast setting is adjusted.
Contrast
Narrows the gap between
brightness and darkness.
Broadens the gap between
brightness and darkness.
Brightness
Black is subdued for
increased overall darkness.
Black is set off for increased
overall brightness.
Adjust to taste.
Colour
Darkens colours.
Lightens colours.
Adjust to taste.
Sharpness
Soft
Sharp
Normally set to Centre position. Shift to the minus (-) side for a softer
effect and plus (+) for a sharper picture.
Hue
Enhances red and weakens
green.
This is adjustable when receiving PAL/SECAM signal.
Enhances green and weakens
Then the character will be grayed out.
red.
Adjust for most realistic skin colour.
Colour Temperature
Cool
Normal
Warm
Normal
Contrast Mode
Auto
Reset
Black / White
Dynamic
(Selects the Reset mode)
YNR
Off
Low
Normally set to Cool.
Dynamic:Emphasizes the differences between video shadings to
improve the feeling of contrast.
Normal : The gradation of an image is reproduced as faithfully as
possible.
Auto:Detects image brightness and automatically adjusts for natural
brightness.
The original factory settings for the items of this Menu page can be
restored by pressing the OK button.
Performs picture signal noise reduction. Turn up to reduce noise.
High
Performs colour signal noise reduction. Turn up to reduce noise.
It will be fixed as Off only when selecting DVI-STB mode.
CNR
Film Mode
Off
On
On:Automatically detects the movie film material and faithfully
reproduces the original film image.
Off:Set to OFF when switching between images does not appear
natural.
PAL Comb Filter
Off
On
This is available only when receiving a PAL composite signal. Turn On
to reduce the discolorations in fine picture detail and provide purer
colour.
LTI
Adjusts the sharpness of the picture signal.
Off
CTI
Low
Middle
High
Black Enhancement
Adjusts the sharpness of the colour signal.
Adjusts the black level compensation.
Auto Colour
Off
On
This is available only when receiving an NTSC composite/S.Video
signal. This monitors and adjusts the colour to maintain constant
colour levels. It also maintains natural flesh tones while preserving
fidelity of background colours.
Colour Temp. Adjustment
Off
On
Turn On when you wish to change colour temperature depending on
the user’s preference.
Amplitude
Red
Green
Blue
Cut Off
36
Setup hint
Dynamic: This setting is best for very bright ambient lighting.
Natural: This setting is for normal lighting conditions.
Red
Brighter scenes are
decreased in reddish colour.
Brighter scenes are increased
in reddish colour.
Brighter scenes are
Brighter scenes are increased
decreased in greenish colour. in greenish colour.
Brighter scenes are
decreased in bluish colour.
Brighter scenes are increased
Adjust colour temperature depending on the user’s preference. These
in bluish colour.
settings are independently stored in each of the 4 Colour Temperature
Dark scenes are decreased in Dark scenes are increased in modes.
reddish colour.
reddish colour.
Green
Dark scenes are decreased in Dark scenes are increased in
greenish colour.
greenish colour.
Blue
Dark scenes are decreased in Dark scenes are increased in
bluish colour.
bluish colour.
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 37
(ブラック 版)
OPERATING INSTRUCTIONS (continued)
▼
▼
Selected characters
Off
Colour Management
Magenta Magenta is weakened.
Setup hint
Turn On when the original balance of each colour is required to adjust
to suit user preferences.
On
Magenta is strengthened.
Red Red is weakened.
Red is strengthened.
Yellow Yellow is weakened.
Yellow is strengthened.
Green Green is weakened.
Green is strengthened.
Cyan Cyan is weakened.
Cyan is strengthened.
Blue Blue is weakened.
Blue is strengthened.
RGB
Colour Decoding
ENGLISH
PICTURE MENU (continued)
R
Red Darkens red only.
G
B
This adjusts listed colours individually to make them either deeper or
more pure. These settings are independently stored in each of the 4
Colour Temperature modes.
Select the single colour screen you need to adjust R/G/B level
individually depending on the user’s preference. Set it back to RGB
mode that indicates each colour (R/G/B) mode after adjusting.
Press the OK button every time the setting is changed.
Lightens red only.
Green Darkens green only.
Lightens green only.
Colour Darkens colours.
Lightens colours.
Enhances red and weakens
Hue green.
This adjusts R/G/B level or tint to make the colour appear natural.
These settings are independently stored in each of the 4 Colour
Temperature modes.
Enhances green and weakens
red.
FUNCTION MENU
2 item is added to the Menu shown in the page 19 .
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
MENU
Video Power Save
Default Zoom
▼
▼
Selected characters
OK
Off
On
Panoramic
4:3
14:9 Zoom
Function
Screen Saver
Screen Wipe
Black Side Panel
Video Power Save
Freeze Mode
Default Zoom
Reset
Select
Set
Off
On 60Min.
Off
Off
Split
Panoramic
Reset
Return
Function
Panel Life
Mode Display
ID Number
Inverse
Standby White
Gamma
Reset
Select
Set
Normal
Off
1
On 60Min.
Off
2.2
Reset
Return
Setup hint
This is used to reduce power consumption for video input when there
is no video signal. Setting it to On will place the monitor to the
standby mode when the AV input with no signal is selected.
This selects the screen display size that appears first when the power
turned on.
37
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 38
(ブラック 版)
OPERATING INSTRUCTIONS (continued)
SETUP MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
MENU
OK
Setup
System
Colour System
Video Input
Audio Input
Scart Output
RGB1
RGB2
Select
OK Set
Setup
System
Colour System
Video Input
Audio Input
Scart Output
RGB1
RGB2
Select
OK Set
Setup
System
Colour System
Video Input
Audio Input
Scart Output
RGB1
RGB2
Select
System1
System
OK
System2
AV1
AV2
AV3
AV4
Monitor
DVI-STB
Component
HDTV
Return
Select
Auto
PAL
SECAM
PAL
Return
Exit
Setup
Video Input
System 1
OK
AV1
AV2
AV3
AV4
Monitor
DVI-STB
Component
HDTV
Return
Select
System 1
OK
Monitor
DVI-STB
Component
HDTV
Return
▼
▼
Selected characters
OK Set
Setup
Colour System
System 1
Setup
Audio Input
AV1
AV2
AV3
AV4
Select
Auto
Composite/Component
Auto
S.Video
Return
Exit
Stereo
L/Mono
Stereo
L/Mono
Return
Exit
Setup hint
Do not change the original setting.
(System1 : Europe/Asia, System2 : North America)
Colour System
AV1
Auto
PAL
SECAM
NTSC3.58
NTSC4.43
This should correspond to the colour system of the signal from the
equipment that is connected to the AV1 video input terminal.
• Normally, set this to Auto. The system of the input signal will be
automatically recognized.
• If the input signal contains a lot of noise or has a low level at Auto and
the operation is erratic, set this to match the input signal.
• When the component signal is received, this setting is not available
(grayed out).
AV2
AV3
(Same to AV1)
AV4
Video Input
AV1
Auto
HDTV
AV2 (1st step)
RGB
Composite/Component
This should correspond to the signal mode of the signal from the
equipment that is connected to AV2 video input terminal.
AV2 (2nd step)
Auto
HDTV
This step should be set only when [Composite/Component] is selected on
the 1st step. The procedure is same as for AV1.
AV4
38
S.Video
SDTV/DVD
This should correspond to the signal mode of the signal from the
equipment that is connected to AV1 video input terminal.
• Normally, set this to Auto. The signal mode of the input signal will be
automatically recognized.
• If the input signal contains a lot of noise or has a low level at Auto and
the operation is erratic, set this to match the input signal.
SDTV/DVD
Composite
• If the signal from the equipment that is connected to the AV4 Scart input
terminal is S.Video or Composite, set this to correspond to that signal.
• If the signal is RGB, it will be automatically recognized and this setting
will have no effect.
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 39
(ブラック 版)
OPERATING INSTRUCTIONS (continued)
▼
▼
Selected characters
ENGLISH
SETUP MENU (continued)
Setup hint
Audio Input
Stereo
AV1
L/Mono
This should correspond to the audio signal from the equipment that is
connected to the AV1 audio input terminal. If the signal is monaural audio,
set this to L/Mono.
AV2
AV3
(Same to AV1)
AV4
Scart Output
Not Available (grayed out)
RGB1
DVI-PC
RGB2 (1st step)
RGB
Auto
RGB2 (2nd step)
DVI-STB
This should correspond to the signal mode of the signal from the
equipment that is connected to the RGB1 DVI terminal.
Component
This should correspond to the signal mode of the signal from the
equipment that is connected to the RGB2 D-sub terminal.
HDTV
SDTV/DVD
This step should be set only when [Component] is selected on the 1st
step.
This should correspond to the signal mode of the signal from the
equipment that is connected to the RGB2 D-sub terminal.
• Normally, set this to Auto. The signal mode of the input signal will be
automatically recognized.
• If the input signal contains a lot of noise or has a low level at Auto and the
operation is found erratic, set this to match the input signal.
OTHER FEATURES
Automatic Store
Approximately 1 sec. after adjustment is completed, the adjustments will be recorded as shown in the table below.
Menu
Picture
Display
Registration condition
Picture Mode
Contrast
Brightness
Colour
Sharpness
Hue
Colour Temperature
Contrast Mode
YNR
CNR
Film Mode
PAL Comb Filter
LTI
CTI
Black Enhancement
Auto Colour
Colour Temp. Adjust
1 setting is registered.
For every input function and every
Picture Mode, 1 setting is
registered.
R Amplitude For every Colour Temperature, 1
setting is registered.
G Amplitude
Menu
Picture
Function
Display
System
Colour System
For every Colour Temperature, 1
setting is registered.
1 setting is registered.
1 setting is registered.
AV1
AV2
AV3
AV4
Video Input
Audio Input
B Cut Off
Red
-
Default Zoom
Setup
R Cut Off
For every input function and every
Colour Management Picture Mode, 1 setting is
registered.
Magenta 1 setting is registered.
1 setting is registered.
Colour For every input function and every
Picture Mode, 1 setting is
Hue registered.
1 setting is registered.
Video Power Save
B Amplitude
G Cut Off
Registration condition
Yellow
Green
Cyan
Blue
Colour Decoding
Red
Green
AV1 1 setting is registered.
AV2
AV4
AV1 1 setting is registered.
AV2
AV3
AV4
RGB1
RGB2
• The previously recorded items will be lost.
39
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 40
(ブラック 版)
TROUBLESHOOTING
Symptoms That Seemingly Appear to be Failures
Make the checks suggested below depending on the symptoms observed. If the symptoms remain uncorrected, contact your dealer.
CAUTION
Customer servicing can be hazardous.
Symptom
• The screen becomes dark and the images cannot be seen
during VCR special playback (fast forward, rewind).
Point to check
See page
• This sometimes occurs when a component output VCR such as
the 480i is connected.
This is not a malfunction; therefore, please take note that this may
occur. When it does occur, change to composite output, or S.video
output.
–
PRODUCT SPECIFICATIONS
This table shows the specifications when the optional video unit has been inserted.
Panel
Display
dimensions
Approx. 42 inches (922 (H) x 522 (V) mm, diagonal 1059mm)
Resolution
1024 (H) x 1024 (V) pixels
Net dimensions
(excluding pedestal)
1030 (W) x 636 (H) x 91 (D) mm
Net weight
(excluding pedestal)
34.9kg
Ambient
conditions
Temperature
Operating : 5˚C to 35˚C, Storage : 0˚C to 40˚C
Relative humidity
Operating : 20% to 80%, Storage : 20% to 90% (non-condensing)
Power supply
AC100 - 240V, 50/60Hz
Power consumption/at standby
365W / <3W
Audio output
12W + 12W (6Ω)
(RGB input)
Input signals
Input terminals
RGB1 DVI input terminal (DVI-D)
RGB1 audio input terminal (3.5mm Stereo Mini Jack)
RGB2 analog RGB input terminal (D-sub 15-pin)
RGB2 audio input terminal (3.5mm Stereo Mini Jack)
Video signals
0.7 V/1.0 Vp-p, analog RGB (Recommended Signal)
480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60
Sync signals
H/V separate, TTL level [2KΩ]
H/V composite, TTL level [2KΩ]
Sync on green, 0.3 Vp-p [75Ω]
Recommended signal
46 modes 29
42
(Video input)
Input terminals
AV1: composite video input terminal (RCA)
AV1: Y PB PR video input terminal (RCA)
AV1: L/R audio input terminal (RCA)
AV2: composite video input terminal (RCA)
AV2: Y/G PB/B PR/R video input terminal (RCA)
AV2: L/R audio input terminal (RCA)
AV3: composite video input terminal (RCA)
AV3: S video input terminal (RCA)
AV3: L/R audio input terminal (RCA)
AV4: composite video / S video / RGB / L/R audio input terminal (Scart)
Video signals
AV1: PAL, SECAM, NTSC4.43, NTSC3.58
AV1: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60
AV2: PAL, SECAM, NTSC4.43, NTSC3.58
AV2: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60, RGB
AV3: PAL, SECAM, NTSC4.43, NTSC3.58
AV4: PAL, SECAM, NTSC4.43, NTSC3.58
AV4: RGB
Input signals
Video output Signal
OUTPUT (MONITOR): composite video monitor-output terminal (RCA)
OUTPUT (MONITOR): L/R audio monitor- output terminal (RCA)
AV4: composite video / L/R audio monitor-output terminal (SCART)
Recommended signal
15 modes 42
• The monitor takes at least 30 minutes to attain optimal picture quality.
40
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 41
(ブラック 版)
PRODUCT SPECIFICATIONS (continued)
ENGLISH
Signal Input
RGB terminal (D-sub 15-pin connector)
Pin
Input signal
1
R (PR/CR)
2
G or sync on green (Y)
3
B (PB/CB)
4
No connection
5
No connection
6
R.GND (PR/CR, GND)
7
G.GND (Y, GND)
8
B.GND (PB/CB, GND)
9
5
15
GND
11
No connection
12
[SDA]
13
H. sync or H/V composite sync
14
V.sync. [V.CLK]
15
[SCL]
(
3
2
1
10
9
8
7
14
13
12
6
11
• When different kinds of input signals are simultaneously input to
the monitor via a graphics board or the like, the monitor will
automatically select the signals in the following priority order:
No connection
10
4
Sync signal type
Priority
H/V separate sync.
1
H/V composite sync.
2
sync.on Green *
3
*There may be instances when correct display is not possible, even
when displaying the signals listed on the following page. In this
case, use H/V separate sync, H/V composite sync.
) : With component input
S-input connector pin specifications
Pin
Input signal
1
2
3
4
Y
Y-GND
C
C-GND
Frame
GND
1
3
2
4
Scart connector pin specifications
Pin
Signal
Pin
1
AUDIO OUT (RIGHT)
12 Not Used
2
AUDIO IN (RIGHT)
13 RGB-R GND
Signal
3
AUDIO OUT (LEFT/MONO)
14 GND
4
AUDIO GND
15 RGB-R / S.VHS CHROMINANCE IN
5
RGB-B GND
16 BLANKING SIGNAL
6
AUDIO IN (LEFT/MONO)
17 COMPOSITE VIDEO GND
7
RGB-B IN
18 BLANKING SIGNAL GND
8
AUDIO/RGB SWITCH / 16:9
19 COMPOSITE VIDEO OUT
9
RGB-G GND
20 COMPOSITE VIDEO / S.VHS LUMINANCE IN
10
Not Used
21 GND / SHIELD (CHASSIS)
11
RGB-G IN
20
18
16
14
12
10
21 19
17
15
13
11
9
8
7
6
5
4
3
2
1
41
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 42
(ブラック 版)
PRODUCT SPECIFICATIONS (continued)
Recommended Signal List
With Digital RGB signal input (RGB1 input)
Signal mode
No.
1
Signal Name
Resolution
Horizontal Dot clock Setup Menu Condition
Vertical frequency frequency frequency
DVI-PC
DVI-STB
(kHz)
(MHz)
(Hz)
640 X 400
70.08
31.47
25.18
○
640 X 480
59.94
31.47
25.18
○
864 X 480
59.94
31.47
34.24
○
4
640 X 480
72.81
37.86
31.50
○
5
640 X 480
75.00
37.50
31.50
○
6
640 X 480
85.01
43.27
36.00
○
7
800 X 600
56.25
35.16
36.00
○
8
800 X 600
60.32
37.88
40.00
○
2
3
9
VGA
W-VGA
VESA
800 X 600
72.19
48.08
50.00
○
10
800 X 600
75.00
46.88
49.50
○
11
800 X 600
85.06
53.67
56.25
○
12
1024 X 768
60.00
48.36
65.00
○
13
1024 X 768
70.07
56.48
75.00
○
14
1024 X 768
75.03
60.02
78.75
○
Remarks
○
WVGA type : On
15
480p
720 X 480
59.94
31.47
27.00
○
16
720p/60
1280 X 720
60.00
45.00
74.25
○
EIA-861
17
1080i/60
1920 X 1080
60.00
33.75
74.25
○
EIA-861
(
EIA-861
: acceptable)
With Composite Input(AV1~AV4 input) and S-video Input (AV3 input).
Signal mode
No.
1
2
Signal Name
NTSC4.43
NTSC3.58
PAL
SECAM
Horizontal
frequency (kHz)
Dot clock
frequency (MHz)
59.94
15.73
—
50.00
15.63
—
Horizontal
frequency (kHz)
Dot clock
frequency (MHz)
15.73
15.63
—
Resolution
Vertical frequency
(Hz)
525
625
Remarks
With R, G, B Video input (AV2 and AV4 input).
Signal mode
No.
1
Signal Name
Resolution
Vertical frequency
(Hz)
NTSC4.43/3.58
PAL, SECAM
525
625
59.94
50.00
Remarks
With component input (AV1, AV2 and RGB2-component input).
Signal mode
No.
Horizontal
frequency (kHz)
Dot clock
frequency (MHz)
50.00
15.63
—
59.94
15.73
—
576
50.00
31.26
—
Signal Name
Resolution
Vertical frequency
(Hz)
1
576i
576
2
480i
480
3
576p
4
480p
480
59.94
31.47
—
5
1080i/50
1080
50.00
28.13
—
6
1080i/60
1080
60.00
33.75
—
7
720p/60
720
60.00
45.00
—
Remarks
• The monitor differentiates the signal modes according to the horizontal and vertical frequencies and the horizontal and vertical sync signal
polarities. Note that different signals having all these elements alike may be handled as the same signal.
• Displaying images with more than 512 lines of vertical resolution at Full diplay (compressed display) can result in the interpolation of stripes.
42
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 43
(ブラック 版)
Optional Tuner Unit Function
The optional tuner unit works when installed with the optional video unit.
Additional functions when the optional tuner unit is installed are as follows: ( 43
~
56
)
ENGLISH
COMPONENT NAMES
Remote control (provided for the optional tuner unit)
This type of remote control is provided for the optional tuner unit as a substitute for the one shown in page
POWER ON / OFF button
PICTURE MODE button
RECALL button
INPUT SELECT button
MENU button
.
AUDIO MODE button
SURROUND button
CH I / II button
MULTI PICTURE (PinP) button
Buttons for MULTI PICTURE mode
RETURN button
SELECT / ADJUST buttons (
D/N
i+
I / II
A/B
MENU
PROGRAM UP / DOWN buttons
2-4-12
P+
-
)
+
OK
VOLUME UP / DOWN buttons
P-
OK button
9
DVD
MUTE button
FREEZE button
ZOOM button
FREEZE
DVD CONTROL buttons
ZOOM
PROGRAM SELECT buttons
1
2
3
4
5
6
7
8
9
PROGRAM UP / DOWN buttons
0
AV1
AV2
AV3
AV4
RGB1
RGB2
RGB / VIDEO buttons
TIME button
Loading Batteries
1. Open the battery cover.
• Slide back and remove the battery
cover in the direction of the arrow.
Handling the Remote Control
Use the remote control within about 5 m from front of the unit’s
remote-control sensor and within 30 degrees on both sides.
2. Load the batteries.
• Load the two Size AA batteries
included, matching polarity marking on
the batteries to those on the case.
With in 30
degrees
With in 30
degrees
About 3m
About 3m
About 5m
D/N
i+
I / II
A/B
MENU
3. Close the battery cover.
2-4-12
P+
-
+
OK
PDV D
• Replace the battery cover in the
direction of the arrow and snap it back
into place.
FREEZE
ZOOM
1
2
4
3
5
7
6
8
9
0
AV1
AV2
AV3
AV4
RGB1
RGB2
ATTENTION
CAUTION
• Do not use new and old batteries together. The batteries could
explode or leak, resulting in fires, physical injury, or stains.
• When loading batteries, observe their correct polarities as
marked on the product. If loaded in the wrong direction, the
batteries could explode or leak, resulting in fires, physical injury,
or stains.
• Do not drop or impact the remote control.
• Do not splash the remote control with water or put it on a wet
object to avoid possible failures.
• Before leaving the remote control out of use for an extended
period of time, remove the batteries from it.
• If the remote control begins to lack responsiveness, replace the
batteries.
• Strong light such as direct sunlight impinging on the
photoreceptor of the remote control can cause operational
failure. Position this unit to avoid direct contact with such light.
43
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 44
(ブラック 版)
COMPONENT NAMES (continued)
Remote control (provided for the optional tuner unit) (continued)
PICTURE MODE
AUDIO MODE
You may recall the picture mode by
pressing this button. Each time you
press it, the picture mode is changed
in the following sequence.
You may recall the audio mode by pressing
this button. Each time you press it, the audio
mode is changed in the following sequence.
Dynamic
Natural
D/N
Movie
Music
Favourite
Speech
MATRIX SURROUND
INPUT SELECT
i+
Press this button to change input
mode.
Press this button to set Matrix
Surround On or Off.
I / II
MULTI PICTURE
RECALL
A/B
MENU
You can see the input mode status on
the screen by pressing this button.
2-4-12
P+
-
Press this button to change the
screen to multi-pictures. Press it
again to return to normal picture.
CH I/II
+
OK
This button is for A2 / NICAM
models only.
MULTI MODE
P-
In multi-picture mode, pressing this
button will change the multi-picture
mode.
DV D
MUTE
DVD CONTROL
FREEZE
You can use these buttons to operate
the selected brand of DVD player.
Press this button to turn off the set
sound. Press again, or press the
volume up button to restore the sound.
ZOOM
1
2
3
4
5
6
7
8
9
PROGRAM SELECT
Press these buttons to select a TV
program directly.
FREEZE
Press this button to change the
picture to freeze mode. Press it again
to return to normal picture.
ZOOM
Press this button to change Picture size.
0
AV1
TIME
Press this button to display the
current time on screen when
receiving a television channel that
provides TELETEXT service.
44
AV2
AV3
AV4
RGB1
RGB2
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 45
(ブラック 版)
COMPONENT NAMES (continued)
ENGLISH
Remote control (provided for the optional tuner unit) (continued)
[Buttons for TELETEXT Mode]
SUBTITLE button
D/N
i+
TV button
I / II
TEXT button
A/B
MENU
COLOUR buttons
(RED, GREEN, YELLOW, BLUE)
2-4-12
P+
-
+
OK
PDVD
FREEZE
ZOOM
MODE button
1
2
4
5
6
7
8
9
TEXT / TV+TEXT button
3
PAGE UP / DOWN button
SUB PAGE buttons
0
AV1
AV2
AV3
AV4
RGB1
RGB2
INDEX button
REVEAL button
TV / TEXT button
HOLD button
CANCEL button
U. N. L. button
TELETEXT FUNCTION
Buttons on Remote Control
TEXT
TV
TV / TEXT
TEXT / TV + TEXT
Function
Press this to use the TELETEXT services.
Press this to return to the TV mode when in the TELETEXT mode.
This switches the receiver between the TV mode and the TELETEXT mode.
In TELETEXT mode, this button switches between TV+TEXT screen (split) and TELETEXT only.
MODE
This selects the FASTEXT and FAVOURITE modes.
INDEX
This selects the P100 page.
SUB PAGE
This allows receiving of a sub page. When the button is pressed, “S✱✱✱✱” will be displayed at the top left of the screen.
SUB TITLE
Use this to access a subtitle service directly rather than through a TELETEXT service (subject to subtitle service broadcasting).
CANCEL
This allows the screen to return to the TV mode temporarily while searching for a required text page. When the required text
page has been received, the page number will be displayed at the top left of the screen. Press the CANCEL button again to
display the TELETEXT screen.
RED
GREEN
YELLOW
BLUE
Each of these buttons selects a link page displayed at the lower part of the screen.
A FAVOURITE page can also be stored in the memory using one of the colours. It can then retrieve the page stored by
pressing the appropriate colour button.
To store a FAVOURITE page :
• press the MODE button ;
• press a colour button for the FAVOURITE page ;
• enter the FAVOURITE page number to be stored and press the same colour button again to confirm.
Each time this button is pressed, the screen display mode changes through the following.
U. N. L
normal state
upper half screen enlarged
lower half screen enlarged
HOLD
REVEAL
PAGE UP / DOWN
This holds the page currently being displayed on the screen. Instead of the page number, a "
the screen. Press this button again to release the hold state.
" indicator appears at the top of
This allows hidden information (found on some teletext pages) to be displayed on the screen.
These buttons increase / decrease the TELETEXT page number.
NOTE
• Certain pages do not show linked pages at the bottom of the screen. To display linked pages, press the INDEX button.
45
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 46
(ブラック 版)
INSTALLATION INSTRUCTIONS
Connecting Antenna
Make sure that the power switch of the monitor is turned off.
Speaker (R)
EUROPE
Monitor rear panel
Speaker (L)
U.K. ONLY
antenna
20
18
16
14
12
10
21 19
17
15
13
11
9
8
7
6
5
4
3
2
1
Precautions when connecting the antenna
• Please use a coaxial cable which is not prone to interference to connect the antenna. Avoid using a parallel
flat feeder wire as interference may occur, causing reception to be unstable and stripe noise to appear on
the screen.
• Avoid using an indoor antenna as this may cause interference. Please use CATV net or outdoor antenna.
• Keep the power cord as far away from the antenna wire as possible.
If there is noise apparent in the picture of VHF-Low band channel, please use double-shielded cable (not
provided) for RF LEADS to reduce the noise.
46
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 47
(ブラック 版)
OPERATING INSTRUCTIONS
POWER ON/OFF
button
ENGLISH
The functions of the buttons located on the bottom
of the monitor change as shown below:
D/N
i+
I / II
INPUT SELECT
button
A/B
MENU
PROGRAM UP/DOWN
buttons
2-4-12
P+
-
+
OK
P-
VOLUME
UP/DOWN buttons
DVD
▼
▼
▼
▼
FREEZE
MUTE button
MENU button
ZOOM
ZOOM button
INPUT SELECT button
(OK button)
PROGRAM UP/DOWN button
(
SELECT button)
1
2
3
4
5
6
7
8
9
PROGRAM SELECT
buttons
0
VOLUME UP/DOWN
buttons
(
ADJUST buttons)
RGB/VIDEO
buttons
AV1
AV2
AV3
AV4
RGB1
RGB2
SUB-POWER button
• ( ) indicates the function while the MENU is displayed on the screen.
Input Switching
Size Switching
• Input can be switched by pressing the AV1, AV2, AV3,
AV4, RGB1 or RGB2 buttons of the remote control. And
the way to return to a TV channel is as follows:
• Pressing INPUT SELECT button at RGB2 input screen.
• Pressing some PROGRAM SELECT buttons and select a TV
channel.
• Pressing PROGRAM UP/DOWN buttons at the screen without
OSD(On-screen display).
• Input can be switched in the sequence of TV ➔ AV1 ➔
AV2 ➔ AV3 ➔ AV4 ➔ RGB1 ➔ RGB2 by pressing the
INPUT SELECT button of the monitor or the remote
control.
TV
RGB2
AV1
AV2
RGB1
AV3
AV4
Each time the ZOOM button of the remote control is
pressed, the screen display size will change and the
status will be displayed at the bottom of the screen.
• During TV mode
Auto
Full
14:9Zoom
Zoom
C14:9L
• [Auto] is a mode which uses WSS (Wide Screen Signals), which
identify the picture format movies and programs are broadcast
in.
Various broadcast stations now transmit WSS. It can be detected
and the monitor will automatically switch to the correct format.
However, some broadcasters do not transmit WSS, and in these
cases monitor will not recognize which format is being
transmitted. Therefore, the Default Zoom setting in the Function
Menu is used to choose when a WSS has not been sent or has
not been detected.
47
012_PDM-4210_G_ENG
2003.12.24 01:16
ページ 48
(ブラック 版)
OPERATING INSTRUCTIONS (continued)
D/N
RECALL button
i+
MULTI PICTURE
button
I / II
A/B
MENU
SELECT buttons
2-4-12
MULTI MODE
button
A/B button
P+
-
+
OK
PDVD
FREEZE
ZOOM
Displaying MULTI PICTURE
If the MULTI PICTURE button on the remote control is
pressed, multiple pictures will display. Three types of
display can be selected by pressing the MULTI MODE
button on the remote control.
The multi picture mode will change in the following
sequence each time the MULTI MODE button is pressed.
2 pictures (Split)
4 pictures
PROGRAM UP/DOWN
buttons
1
2
3
4
5
6
7
8
9
0
AV1
AV2
AV3
AV4
RGB1
RGB2
12 pictures
Activating the Split mode from the TV screen
Pressing the MULTI PICTURE button one time will display 2 pictures.
• The speaker icon can be shifted left and right by pressing the A/B button; the audio will be output from the
side on which the speaker icon is located.
• The same signal input cannot be selected for both screens at the same time.
• The TV channel can be changed by pressing the
and
PROGRAM UP/DOWN buttons on the remote
control.
• The signal input mode of picture-A or picture-B (the one that the speaker icon is located on) can be selected
by pressing INPUT SELECT button on the remote control.
• Pressing the MULTI PICTURE button once again will cancel the multi picture mode.
• When the Video input is set to RGB Video, multi picture mode is not possible.
• Refer to the table for 2 pictures (Split) mode. 49
5
AV1
A
B
Activating the 4 pictures mode from the TV screen
Pressing the MULTI MODE button one time at the 2 pictures mode will display 4 pictures.
AV1
• Press [A/B] button to select picture A or picture B indicated by a red triangle. For pictures on right, press
SELECT buttons to select picture. The selected channel number would change green.
• The TV channel can be changed by pressing the
and
PROGRAM UP/DOWN buttons on the remote
control.
• The audio can only be output from picture A in the 4 picture mode.
• The same signal input mode cannot be selected for each screens at the same time.
• Pressing the MULTI PICTURE button from the 4 picture mode will cancel the multi picture mode. Pressing the
MULTI PICTURE button again will display the 4 pictures.
• Refer to the table for 4 pictures mode. 49
Activating the 12 pictures mode from the TV screen
Pressing the MULTI MODE button one time at the 4 pictures mode will display 12 pictures.
• Starting from channel 1, preset channels will automatically display in sequence on the 12 windows.
• This function activates only in TV mode.
• After several seconds, it refreshes the picture one by one.
• Pressing the MULTI PICTURE button at the 12 picture mode will cancel the multi picture mode. Pressing the
MULTI PICTURE button again will display the 12 pictures again.
• Pressing the MULTI MODE button from the 12 picture mode will display the 2 pictures (Split) mode.
A
B1
8
B2
6
B3 11
1
2
3
4
5
6
7
8
9
10
11
12
NOTE
• Even if the input of the horizontal / vertical synchronizing signal (or video signal) stops during multi picture display, the mode will not change
to power save mode.
• Please be careful since image retention will occur if the plasma display is left in a multi picture display state for a long period of time.
48
012_PDM-4210_G_ENG
2003.12.24 01:17
ページ 49
(ブラック 版)
OPERATING INSTRUCTIONS (continued)
ENGLISH
Displaying MULTI PICTURE (continued)
2 Pictures (Split)
Input terminal
Sub
Main
AV1
~AV4
AV1~AV4
AV1, AV2
RGB1
RGB2
TELE
PAL
NTSC3.58 576i 480i
1080i/50 1080i/60 720p/60 STB Component TEXT
SECAM NTSC4.43 576p 480p
Main
Sub
PAL, SECAM
NTSC3.58/4.43
576i, 576p
480i, 480p
AV1
AV2
1080i/50
1080i/60
720p/60
RGB1
STB
RGB2
Component
(
: Available)
4 Pictures
Input terminal
Sub
Main
AV1
~AV4
AV1~AV4
AV1, AV2
RGB1
RGB2
TELE
PAL
NTSC3.58 576i 480i
1080i/50 1080i/60 720p/60 STB Component TEXT
SECAM NTSC4.43 576p 480p
Main
Sub 1
PAL, SECAM
Sub 2
NTSC3.58/4.43
576i, 576p
Sub 3
480i, 480p
AV1
AV2
1080i/50
1080i/60
720p/60
RGB1
STB
RGB2
Component
(
: Available)
Input Signal Screen Display
The TV channel status can be displayed on the screen by
pressing the RECALL button of the remote control.
• The display will disappear in approximately 6 seconds.
TV
Off-timer
On-timer
1
ABCDE
OFF
-- -- Min.
-- -- : -- --
I
TV position
Name
Sound mode
Sound system
49
012_PDM-4210_G_ENG
2003.12.24 01:17
ページ 50
(ブラック 版)
OPERATING INSTRUCTIONS (continued)
D/N
i+
I / II
A/B
MENU
2-4-12
P+
-
+
OK
PDVD
FREEZE
FREEZE button
ZOOM
1
2
3
4
5
6
7
8
9
0
AV1
AV2
AV3
AV4
RGB1
RGB2
Picture Freezing
[Split]
When the FREEZE button on the remote control is pressed, the screen transfers into the
freeze mode.
5
• There are two types of Picture Freeze mode, Split and Strobe. You can select them at the “Freeze Mode”
setting of the Function Menu.
• The Split mode will display 2 pictures from the same source on the screen with one active picture and the
other still.
• The Strobe mode will display 12 pictures with the last picture active, while other 11 windows are still.
• Pressing the FREEZE button again changes the screen back to the normal picture.
• This function is also available from video input mode besides TV mode. Refer to the table for Freeze function
as below:
Split
A
B
[Strobe]
1
2
3
4
5
6
7
8
9
10
11
12
Active
Strobe
PAL, SECAM
NTSC3.58/4.43
576i
480i
576p
480p
1080i/50
1080i/60
720p/60
RGB, DVI-PC
(
: Available)
FUNCTION MENU
Refer to the page 37 . (In the same way as when the optional video unit is attached)
But 1 item is added and 5 items are deleted.
Freeze Mode
50
▼
▼
Selected characters
Split
Strobe
Setup hint
This switches the display condition of the FREEZE mode between Split
(2 pictures) and Strobe (12 pictures).
Mode Display
Not Available (grayed out)
ID Number
Not Available (grayed out)
Inverse
Not Available (grayed out)
Standby White
Not Available (grayed out)
Gamma
Not Available (grayed out)
012_PDM-4210_G_ENG
2003.12.24 01:17
ページ 51
(ブラック 版)
OPERATING INSTRUCTIONS (continued)
ENGLISH
SETUP MENU
[During TV mode]
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
MENU
OK
Setup
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Auto Off
Select OK Set
Setup
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Auto Off
Select OK Set
Setup
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Auto Off
Select OK Set
Setup
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Auto Off
Select OK Set
OK
Off
Return
OK
Off
Return
Setup
Manual Tuning
Position
Search
Descrambler
Name
Sound System
Colour System
Skip
NR
Select
Return
99
C 22
Off
ABCDE
BG
Auto
Off
Off
Exit
Setup
Fine Tuning
Select
Prog.No.199
+56
Return
OK
Off
Return
Setup
Sort
Position
100
101
102
103
104
105
106
107
OK
Off
Return
Name
ABCDE
BBC1
----BBC
FGHIJ
XYZAB
---------
Select
Setup
Auto Tuning
Country
Austria
Belgium
Croatia
Czech Republic
Denmark
Finland
France
Germany
Setup
Auto Tuning
Country
Greece
Hungary
Iceland
Ireland
Italy
Netherlands
Norway
Poland
Search
Select
Set
Return
Select
C.S.MHz
471MHz
C25
C40
C30
S27
S41
225MHz
C51
Return
Exit
Setup
Auto Tuning
Country
Portugal
San Marino
Spain
Sweden
Switzerland
Turkey
United Kingdom
Search
OK
Adjust
Search
OK
Set
Return
Select
OK
Set
Return
OK
Setup
Auto Tuning
Country
Setup
Auto Tuning
Portugal
San Marino
Spain
Sweden
Switzerland
Turkey
United Kingdom
Scanning Channel Number: 33
OK
Cancel
OK
Cancel
Search
Select
OK
Set
Return
51
012_PDM-4210_G_ENG
2003.12.24 01:17
ページ 52
(ブラック 版)
OPERATING INSTRUCTIONS (continued)
▼
Selected characters
▼
SETUP MENU (continued)
Setup hint
(Page3)
Select the country name using the ▼ ▲ SELECT buttons and press
OK button.
• If some required stations could not be preset using the auto tuning
function, select and preset the required station in the required
position using the manual tuning operation.
Auto Tuning
Country
(Page1)
Search
–
(Page2)
–
Press the OK button and it starts the auto tuning.
Manual Tuning
Position
1
2
3••••••199
AV00
Set the position number. This also can be set by ▼ ▲ PROGRAM
UP/DOWN buttons.
Search
–
–
Select the channel entry method. Enter a two digit channel number
(CH), a two digit S-band number, or a 3 digit frequency (MHz).
(C--)
–
–
Use the 0-9 NUMBER buttons to enter a two digit number. If the number
is a standard channel number, the unit begins searching for the channel.
(S--)
–
–
Use the 0-9 NUMBER buttons to enter a two digit number. If the number
is a standard S-band number, the unit begins searching for the channel.
(--MHz)
–
–
Use the 0-9 NUMBER buttons to enter a three digit number. If the number
is a standard frequency, the unit begins searching for the channel.
Off
Set this to Off normally. If it is set to On, the AV4 (Scart) terminal
operates as TV signal input, and the screen changes to display AV4
(Scart) input signal automatically.
On
This is used to input a 5 digit name for a TV station. After fixing the
cursor on the first digit, select a letter by ▼ ▲ SELECT buttons and
move to the next digit by
ADJUST button. Press the OK button
again when finished.
• Selectable letters are “0”~`”9”, ”A”~`”Z”, “+”, “–”, ” ”(blank),
”,”(comma) and ”.”(period) .
▼
Descrambler
Name
( :a letter)
Sound System
BG
I
Colour System
Auto
PAL
NTSC3.58
L'
DK
Select one of 5 different settings for the sound system.
L
SECAM
NTSC4.43
Select one of 5 different settings for the colour system.
Skip
Off
On
If this is set to On, the selected position will be skipped while
selecting positions by PROGRAM UP/DOWN buttons.
This is automatically set to On for non-broadcasting channels.
NR
Off
On
If this is set to On, it helps to reduce the noise interference visible on
the screen, especially in weaker signal reception areas.
Fine Tuning
After completing fine-tuning, press the RETURN button to exit this
Decreasing the frequency Increasing the frequency
mode.
data for the main tuner
data for the main tuner.
• The variable range is -56 ~ +56.
Sort
(Position list
designated rows)
–
–
Off
Auto Off
Move the cursor to the row of the channel you wish to change, and press
the OK button. The display characters change to green. Use the ▼ ▲
SELECT buttons to move the row to the disired location, and press the
OK button when you have finished. Press the RETURN button to exit.
If this is set to On, the power will be turned off when there is no
transmission signal and no operation for about 10 minutes in the TV
mode.
On
[During VIDEO signal input]
1 item is added to the Menu shown in the page 39 .
Scart Output
52
▼
▼
Selected characters
TV
Monitor
Setup hint
TV:AV4 (Scart) output will be fixed as TV signal output.
Monitor:AV4 (Scart) output can view the same image as displayed on
the main unit. It is possible to monitor only the composite video signal
from AV1, AV2, or AV3 input that is displayed on the screen at the time.
• If Descrambler is set to On, it will be fixed as TV automatically.
012_PDM-4210_G_ENG
2003.12.24 01:17
ページ 53
(ブラック 版)
OPERATING INSTRUCTIONS (continued)
ENGLISH
OTHER FUNCTIONS
A2 / NICAM / Sound Multiplex
• The CH I / II button is only useful for NICAM and sound multiplex signals.
Otherwise pressing this button will have no effect.
8
BILINGUAL / DUAL sound broadcast
NICAM [II]
When bilingual program is received, sound mode display appears in yellow as shown on
right.
Press the CH I / II button to select the sound to be heard.
Each time the button is pressed, I, II or ▼ (force mono) appear cyclically on the screen.
When receiving NICAM signals, NICAM display will appear as below.
Sound multiplex signal received
Yellow
Green
Yellow
NICAM signal received
[I]
[II]
Yellow
Yellow
NICAM [II]
NICAM [I]
Select I, II or
Green
(force mono) to hear the CH I, CH II or MONO broadcast respectively.
STEREO sound broadcast
8
When a stereo program is received, the sound mode display will appear in red, and you can
press the CH I / II button to select either stereo or mono sound.
Each time the button is pressed,
or ▼ (force mono)appear cyclically on the screen.
When receiving NICAM signals, the NICAM display will appear as below.
Sound multiplex signal received
Red
Green
NICAM signal received
NICAM
Select
or
Red
Green
(force mono) to hear the STEREO or MONO broadcast respectively.
Monaural sound broadcast
When a monaural program is received, the sound mode display will appear in green.
You can press the CH I / II button to swith the sound mode between monaural and forced
mono (sounds are identical).
Each time the button is pressed,
or ▼ (force mono) appear cyclically on the screen.
8
NOTE
• If the sound signal is not strong enough for quality reception, press the CH I / II button until ▼ appears on the screen to receive a clear mono sound.
• If the sound signal has hiss noise or the plasma monitor keeps switching between stereo and mono mode due to signal condition, press the
CH I / II button until ▼ appears on the screen to receive a clear mono sound.
53
012_PDM-4210_G_ENG
2003.12.24 01:17
ページ 54
(ブラック 版)
OPERATING INSTRUCTIONS (continued)
OTHER FUNCTIONS (continued)
DVD Player Selection
• You can use this remote control to operate various, brands of DVD player by pressing the following buttons on the remote control
simultaneously.
YAMAHA
Press
RECALL
3
or
5
RECALL
Other brands
Brands of DVD Player
Press
Brands of DVD Player
Press
Hitachi
RECALL
1
RCA
RECALL
9
Pioneer
RECALL
2
Mitsubishi
RECALL
0
Panasonic
RECALL
3
Onkyo
RECALL
INDEX
Toshiba
RECALL
4
Zenith
RECALL
MODE
Philips
RECALL
5
Orion
JVC
RECALL
6
Shinco
RECALL
CANCEL
Samsung
RECALL
7
Skyworth
RECALL
REVEAL
Sony
RECALL
8
Bubuko
RECALL
TV/TEXT
RECALL
Example
To operate a YAMAHA DVD player, press and hold the RECALL button, followed by the
3
or
5
button.
D/N
i+
I / II
A/B
MENU
RECALL button
2-4-12
P+
-
+
OK
PDVD
FREEZE
ZOOM
MODE button
1
2
3
4
5
6
7
8
9
SUB PAGE buttons
0
AV1
AV2
AV3
AV4
RGB1
RGB2
INDEX button
TV / TEXT button
CANCEL button
NOTE
• Not all models of the listed brands can be operated using this remote control.
54
REVEAL button
SUB PAGE
012_PDM-4210_G_ENG
2003.12.24 01:17
ページ 55
(ブラック 版)
TROUBLESHOOTING
ENGLISH
Symptoms That Seemingly Appear to be Failures
Make the checks suggested below depending on the symptoms observed. If the symptoms persist, contact your dealer.
CAUTION
Customer servicing can be hazardous.
Symptom
Possible reason
Remedy
(1) Connection of antenna cable to the TV is
poor.
(2) Corroded or poor antenna connections.
(3) Antenna has moved position.
(4) Adverse weather conditions.
(5) Transmitter problems.
(1) Make new connection and/or change antenna
plug.
(2) Make new connections or renew cable.
(3) Re-align antenna.
(4) None.
(5) Check with local Operator.
(1) Antenna has moved position.
(2) TV not tuned correctly.
(3) Adverse weather conditions.
(4) Transmitter problems.
(5) AV Input not set correctly.
(1) Re-align antenna.
(2) Re-tune or fine tune TV.
(3) None.
(4) Check with local Operator.
(5) Check the external equipment connected.
snowy picture - poor sound
multiple images - sound O.K
(1) Interference from electrical or mechanical (1) Check devices for shielding and renew if
motors, fluorescent lights, portable
necessary or move further from TV.
radios etc.
intermittent interference
(1) TV may be in AV mode.
(2) Picture/sound setting set to minimum.
(3) TV in standby or power save mode.
(1) Press the INPUT SELECT button or 0 to 9 buttons
on your remote control to return to normal TV
mode.
(2) Check picture / sound controls (go to MAIN
MENU).
(3) Press POWER ON / OFF button.
no picture or sound
55
012_PDM-4210_G_ENG
2003.12.24 01:17
ページ 56
(ブラック 版)
PRODUCT SPECIFICATIONS
This table shows the specifications when the optional video unit and tuner unit have been inserted.
Panel
Display
dimensions
Approx. 42 inches (922 (H) x 522 (V) mm, diagonal 1059mm)
Resolution
1024 (H) x 1024 (V) pixels
Net dimensions
(excluding pedestal)
1030 (W) x 636 (H) x 91 (D) mm
Net weight
(excluding pedestal)
34.9kg
Ambient
conditions
Temperature
Operating : 5˚C to 35˚C, Storage : 0˚C to 40˚C
Relative humidity
Operating : 20% to 80%, Storage : 20% to 90% (non-condensing)
Power supply
AC100 - 240V, 50/60Hz
Power consumption/at standby
365W / <3W
Audio output
12W + 12W (6Ω)
(RGB input)
Input signals
Input terminals
RGB1 DVI input terminal (DVI-D)
RGB1 audio input terminal (3.5mm Stereo Mini Jack)
RGB2 analog RGB input terminal (D-sub 15-pin)
RGB2 audio input terminal (3.5mm Stereo Mini Jack)
Video signals
0.7 V/1.0 Vp-p, analog RGB (Recommended Signal)
480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60
Sync signals
H/V separate, TTL level [2KΩ]
H/V composite, TTL level [2KΩ]
Sync on green, 0.3 Vp-p [75Ω]
Recommended signal
46 modes 29
42
(Video input)
Input terminals
AV1: composite video input terminal (RCA)
AV1: Y PB PR video input terminal (RCA)
AV1: L/R audio input terminal (RCA)
AV2: composite video input terminal (RCA)
AV2: Y/G PB/B PR/R video input terminal (RCA)
AV2: L/R audio input terminal (RCA)
AV3: composite video input terminal (RCA)
AV3: S video input terminal (RCA)
AV3: L/R audio input terminal (RCA)
AV4: composite video / S video / RGB / L/R audio input terminal (Scart)
Video signals
AV1: PAL, SECAM, NTSC3.58, NTSC4.43
AV1: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60
AV2: PAL, SECAM, NTSC3.58, NTSC4.43
AV2: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60, RGB
AV3: PAL, SECAM, NTSC3.58, NTSC4.43
AV4: PAL, SECAM, NTSC3.58, NTSC4.43
AV4: RGB
Input signals
Recommended signal
OUTPUT (MONITOR): composite video monitor-output terminal (RCA)
OUTPUT (MONITOR): L/R audio monitor- output terminal (RCA)
AV4: composite video / L/R audio output terminal (SCART)
Recommended signal
15 modes 42
(RF input)
Input terminals
ANT : 75Ω Unbalanced
RF Video System
PAL B, G, H / I / D, K
SECAM B, G / D, K / K1 / L, L'
Input signals
• The monitor takes at least 30 minutes to attain of optimal picture quality.
56
021_PDM-4210_G_FRA_caution
2003.12.23 16:47
ページ 1
(ブラック 版)
FRANÇAIS
Manuel Utilisateur
Nous vous remercions d’avoir acheté Yamaha Moniteur Plasma
Haute Définition.
Avant d’utiliser votre écran, veuillez lire attentivement ce manuel afin
de savoir comment opérer de manière sûre et adéquate votre
écran. Veuillez conserver ce manuel dans un endroit sûr afin de
pouvoir vous y référer ultérieurement. Celui-ci vous sera utile à
l’avenir.
Remarques concernant les travaux
d’installation :
Ce produit est commercialisé en présumant qu’il sera installé par
une personne qualifiée possédant les connaissances et les
compétences indispensables. Ce produit doit dans tous les cas
être installé et réglé avant emploi par un installateur spécialisé ou
votre revendeur. YAMAHA ne peut assumer aucune
responsabilité pour des dégâts ou des endommagements
causés au produit à cause d’une erreur commise lors de
l’installation ou du montage, d’une utilisation fautive ou
inadéquate, d’une modification du dispositif ou encore d’un
endommagement provoqué par un désastre naturel.
Remarques à l’attention des revendeurs :
Après l’installation, veillez à bien remettre au client ce manuel et
à lui expliquer comment utiliser le produit.
Remarques concernant ce Manuel
• Les informations contenues dans ce Manuel peuvent être
modifiées dans préavis.
• Bien que des soins méticuleux ont été pris dans la préparation
de ce Manuel, nous vous prions de contacter votre revendeur
ou notre société si vous avez des commentaires, des avis ou
des questions concernant notre produit.
• Il convient de comprendre parfaitement les conditions
préalables requises à l’utilisation de ce produit, telles que les
caractéristiques et les spécifications techniques concernant le
matériel et le logiciel et les contraintes, lorsque vous utilisez ce
produit. Nous n’assumerons aucune responsabilité pour les
dégâts causés par une utilisation fautive ou inadéquate de ce
produit.
• La reproduction totale ou partielle de ce Manuel sans notre
autorisation préalable est interdite.
• Les noms de produit mentionnés dans ce Manuel peuvent être
des noms de marque ou des marques déposées appartenant
à leurs propriétaires respectifs.
1
Download PDF

advertising