Timing Relays 120 700
Bulletin 700-FS
Timing Relays
Overview/Product Selection
Bulletin 700-FS
Table Of Contents
•
•
•
•
•
Product Selection . . . . . . . 120
Accessories . . . . . . . . . . . . 122
Connection Diagrams . . . . 123
Specifications . . . . . . . . . . 126
Adjustable Function and Timing Range Timing Relays
DIN Rail Mounted without Cost of Socket
22.5 mm Wide Multifunction or Single Functions
Available as SPDT or DPDT Contact Output, 8 A
Timing Ranges From 0.05s…60h
Catalog Number Explanation
700 – FS H
3 U U23
First Position
Bulletin Number
Sixth Position
Supply Voltages
Second Position
Type of Relay
Fifth Position
Fourth Position Time Ranges
Assembly of Contacts
Third Position
Function
Single-Function (With SPDT 1 C/O contacts)
700-FS
A
3
A
U23
Function
Contact Outputs
Time Ranges
Supply Voltages
A On-delay ➊
B Off-delay ➊
C On- and off-delay ➊
D One shot ➊
E Fleeting off-delay ➊
F Flasher (repeat cycle starts with pulse) ➊
G Flasher (repeat cycle starts with pause) ➊
I On-delay pulse generator ➊
J On-delay (pulse controlled) ➊
K One shot / watch dog
(pulse controlled) ➊
L Pulse converter ➊
All functions:
3 1 Changeover contact
(SPDT)
1 C/O
A 0.05…1 s
B 0.15…3 s
C 0.5…10 s
D 1.5…30 s
E 0.05…1 min
F 0.15…3 min
G 0.5…10 min
H 1.5…30 min
I 0.05…1 h
J 0.15…3 h
K 0.5…10 h
L 3.0…60 h
U 0.05 s…60 h ➋
Z12 12V DC
U23 24…48V DC
24…240V AC 50/60 Hz
.
Single Function (With 2PDT 2 C/O contacts)
Functions Available
Contact Outputs
ON-Delay
(DPDT) 2 C/O
ON-Delay
(DPDT) 2 C/O
OFF-Delay
(DPDT) 2 C/O
OFF-Delay
(DPDT) 2 C/O
Time Ranges
0.05 s…60 h ➌
Supply Voltages
12V DC
24…48V DC
24…240V AC
50/60 Hz
12V DC
24…48V DC
24…240V AC
50/60 Hz
➊ Factory-stocked item.
➋ Valid for functions "A" and "B" only.
➌ The time range of "0.05 s…60 h" is selectable in 12 smaller ranges plus an ON and OFF function for maintenance needs.
120
Cat. No.
Factorystocked Item
700-FSA4UZ12
700-FSA4UU23
✔
700-FSB4UZ12
700-FSB4UU23
✔
Bulletin 700-FS
Timing Relays
Product Selection, Continued
Multi-Function (This device offers you the flexibility of selecting one of 8 single timing functions.)
Functions Available
Contact Outputs
M Multi-function timing relays
8 Single-functions:
A, B, C, D, E, F, I, and L
ON and OFF function additional
(for installation and maintenance)
note: See next page for function description.
Time Ranges
(SPDT) 1 C/O
(SPDT) 1 C/O
0.05 s…60 h ➊
(DPDT) 2 C/O
(DPDT) 2 C/O
Supply Voltages
12V DC
24…48V DC
24…240V AC
50/60 Hz
12V DC
24…48V DC
24…240V AC
50/60 Hz
Cat. No.
Factorystocked Item
700-FSM3UZ12
✔
700-FSM3UU23
700-FSM4UZ12
✔
700-FSM4UU23
Special Function
Functions Available
Contact Outputs
Time Ranges
0.05 s…60 h ➊
Flasher (Repeat cycle starting with pulse or
pause)
SPDT (1 C/O)
2 x0.05 s…60 h (2
ranges)
OFF-delay without supply voltages (True
OFF-delay)➌
SPDT (1 C/O)
DPDT (2 C/O)
0.15 s…10 m ➋
0.5 s…10 s
1.5…30 s
2 N.O. + 1 common 0.05 s…1 min.
0.15…3 min.
0.5…10 min.
Star-Delta
Supply Voltages
12V DC
24…48V DC
24…240V AC
50/60 Hz
12V DC
24…48V DC
24…240V AC
50/60 Hz
24…240V DC
24…240V AC
50/60 Hz
24…48V DC
24…240V AC
50/60 Hz
Factorystocked
Item
Cat. No.
700-FSH3UZ12
700-FSHUU23
700-FSH3VZ12
700-FSH3VU23
✔
700-FSQ3QU18
✔
700-FSQ4QU18
✔
700-FSY2CU23
700-FSY2DU23
700-FSY2EU23
700-FSY2FU23
700-FSY2GU23
➊ The time range of "0.05 s…60 h" is selectable in 12 smaller ranges plus an ON and OFF function for maintenance needs.
➋ This time range is selectable in four smaller ranges: 0.15 s…2.5 s, 0.5 s…10 s,4 s…80 s, 30 s…10 min.
➌ Due to shock during shipment, the state of the contacts should be verified before initial use.
Multi-Function Timing Relay Function and Time Range Settings
Description
Up
Down
700-FSM4
Multi-function timing relays 700-FSM3U includes 10 setting
functions:
(A)On-delay
(B)Off-delay
A
(C)On- and off-delay
(D)One shot
(E)Fleeting off-delay
(F)Flasher (repeat cycle starts with pulse)
(I)On-delay pulse generator
(L)Pulse converter
(On)ON-Function *
(Off)OFF-Function *
* (for installation and maintenance)
Note: Switch ⊗ is on DPDT relays only. When switch is
down, one contact is instantaneous and one is timed.
When switch is up, both contacts are timed.
SPDT
DPDT
Multi-Time Setting Range 0.05 s…60 h
(1 s)0.05…1 s
(3 s)0.15…3 s
(10 s)0.5…10 s
(1 min)0.05…1 min
(3 min)0.15…3 min
(10 min)0.5…10 min
(1 h)0.05…1 h
(3 h)0.15…3 h
(10 h)0.5…10 h
10h
(60 h)3.…60 h
121
Bulletin 700-FS
Timing Relays
Accessories
Qty.
Cat. No.
Setting Knob with Scale
(for time setting without tools)
10
700-FSK
Panel Mounting Adapter
For surface mounting according to drilling plan EN 50 002
5
199-FSA
Labeling Sheet: 10 sheets with 105 self-adhesive paper labels each, 6 x 17 mm
10
100-FMS
Marking Tag Sheet: 10 sheets with 160 perforated paper labels each, 6 x 17 mm
10
100-FMP
Transparent Cover: To be used with marking tag sheets
100
100-FMC
100
100-FMA2 ➊
Description
Marking Tag Carrier: To be used with label strip
System Bulletin 1492-W
➊ Cat. No. 100-FMA2 is only a marking tag carrier. Please refer to the Terminal Block Accessories section, page 12-174 of publication A113 for appropriate marker
cards to be used with this carrier.
122
Bulletin 700-FS
Timing Relays
700-FS Function and Connection Diagrams
(A) On-Delay
(B) Off-Delay (Min. Pulse AC 50 ms…DC 30 ms)
➊
1c/o (SPST)
Output
1c/o (SPST)
Output
➊
2 c/o (DPDT)
Output 1
2 c/o (DPDT)
Output 1
Output 2
Output 2
Output 2
➋
➋
Output 2
➌
➋
(C) On- and Off-Delay
➌
➋
(D) One Shot
➊
Output
Output
➌
➌
(E) Fleeting Off-Delay (Min. Pulse AC 50 ms…DC 30 ms)
(F) Flasher (Repeat Cycle Starts with Pulse)
➊
Output
Output
➌
➌
(G) Flasher (Repeat Cycle Starts with Pause)
Output
(I) On-Delay Pulse Generator
Output
➌
(J) On-Delay (Pulse Controlled)
(K) One Shot/ Watch Dog (Pulse Controlled)
➊
➊
Output
Output
(Off) OFF-Function
(On) ON-Function
(L) Pulse Converter (Min. Pulse AC 50 ms…DC 30 ms)
➊
Output 1
Output 1
Output 2
Output 2
Output
➌
Cleverly Designed Function Display LED (Green)
Output in rest position, no timing
Output in rest position, time running
Output in operation position, no timing
Output in operation position, time running
➊ A voltage other than the supply voltage can be used at B1, but must be within voltages specified on timer.
➋ Output 2 is selectable as instantaneous contact with sliding switch (⊗) on front panel (instantaneous when switch is down, timed when switch is up).
➌ Available on multifunction "M," and single function "A" or "B" option timing relays along with code "4" (2PDT contacts). Bridge or potentiometer 10 kΩ, min. 0.25 W
(low voltage) for external time setting. Set timer dial to 0.0.
123
Bulletin 700-FS
Timing Relays
Connection Diagrams, Continued
Special Function Flasher (Repeat Cycle Starting with Pulse or Pause) Timing Relays
Description
t2 Setting
Up
Switch
Down
1 Range Setting
Separate Range Settings
t1 Setting
700-FSH3U
700-FSH3V
Supply Voltages (A1/A2)
Z12 12V DC
U23 24…48V DC,
24…240V AC, 50/60 Hz
Function Diagram / Connection Diagram
(H) Flasher (Repeat Cycle Starting with Pulse or Pause)
The repeat cycle timer permits different settings for on and off times.
The following operating modes are possible:
• Oscillating mode; repeat cycle starts with voltage applied at A1 and B1, and continues to repeat until voltage is off.
• One cycle mode; started by energizing B1 with voltage on A1 and A2.
• Output starts with pulse or pause (switch ⊗ Up or Down).
• 700-FSH3U provides (1) range setting for t1 and t2.
700-FSH3V provides (2) range settings for t1 and t2.
Supply Voltage Controlled, Oscillating Mode Starting with Pause — Switch ⊗ is Up
Output
Supply Voltage Controlled, Oscillating Mode Starting with Pulse — Switch ⊗ is Down
Output
Pulse Controlled, Output Starts With Pause (Min. Pulse AC 50 ms — DC 30 ms) — Switch ⊗ is Up One Cycle
Mode — Voltage Supplied at A1 and A2, then Pulsing “s” to Energize B1 will Initiate One Cycle.
Output
Pulse Controlled, Output Starts with Pulse (Min. Pulse AC 50 ms — DC 30 ms) — Switch ⊗ is Down One Cycle
Mode — Voltage Supplied at A1 and A2, then Pulsing “s” to Energize B1 will Initiate One Cycle.
Output
Note: If B1 is pulsed, a one full time cycle consisting of t1 and t2 is completed.
LED Operation Chart — Green LED
Output at Shelf State, No Timing _ LED Off
Output at Shelf State, Time is Running _ LED Flashing
Output NO Contact is Closed, No Timing _ LED On
Output NO Contact is Closed, Time is Running _ LED Long Flashing
124
Bulletin 700-FS
Timing Relays
Connection Diagrams, Continued
Function Diagram/Connection Diagram
(Q) Off-Delay without Supply Voltage (True Off-Delay) — When input power is turned on, the output contact changes state. When the power is removed, the time
delay begins. The output contact returns to shelf state at the end of the time delay.
Note: Min. pulse (t) required:
24V DC: 200 ms
24V AC: 325 ms
240V DC: 200 ms
240V AC: 175 ms
Output
Output 1
Output 2
LED
A1/A2
18
15 16
28
25 26
(Y) Star-Delta Timing Relay — When power is applied, the output contact 17/18(Y) changes state. After the time setting, the output contact 17/18(Y) returns to shelf
state. After the fixed time (50… 60 ms), the output contact 17/28∆ changes state. Both output contacts return to shelf state whenever the power is removed.
125
Bulletin 700-FS
Timing Relays
Specifications ➊
Time Characteristics (according to VDE 0435, Part 2021)
Setting Accuracy
Repeatability
Tolerance
±5% of full scale
±0.2% of the setting values
Voltage: ±0.001%/%∆U
Temperature: ±0.025%/°C
Supply
Supply Voltages
Voltage Tolerance
Power Consumption
Time Energized
Reset Time
Voltage Interruption
Cable Length
(Supply Voltage Control)
Cable Length
Vibration Resistance
Shock Resistance
Protection Class
24…48V DC and 24…240V AC, 50/60 Hz
(multi voltage)
–20…+20% (DC), –15…+10% (AC)
0.5 W at 24V DC, 5 VA at 240V AC
100%
50 ms
≤ 20 ms without reset (supply voltage)
Weight
Approval
Ambient Temperature
Max. 250 m (800 ft)
Terminals
Pulse Control (B1)
Pulse Duration
Input Voltage
Input Current
Max. Leakage Current
Climatic Withstand
≥ 50 ms (AC), ≥ 30 ms (DC)
Supply voltage range
1 mA
400 micro Amps
Max. 250 m (800 ft) without parallel load between
B1 and A2
Max. 50 m (160 ft) with load (<3 kΩ) between B1
and A2
Mounting
Disposal
Outputs
Contact Type
Switching Capacity
Short-Circuit Resistance
Life
State Indicator
Relay as changeover switch
Voltage: 440V AC
Current Ith (AC-1): 8 A (5 A for 700-FSQ)
Power: 2000 VA
According to IEC 947-5-1:
3 A/440V AC (inductive load, AC 14)
3 A/250V AC (inductive load, AC 15)
1 A/24V DC (inductive load, DC 13)
According to UL 508:
1.5 A/250V AC (B300)
3 A/120V AC (B300)
10 A gL
Mechanical: 30 million operations
Electrical operations:
4 Mil. at 1 A/250V AC, cos ϕ = 1
0.2 Mil. at 6 A/250V AC, cos ϕ = 1
1.5 Mil. at 1 A/250V AC, cos ϕ = 0.3
0.3 Mil. at 3 A/250V AC, cos ϕ = 0.3
0.5 Mil. at 6 A/24V DC, resistive
2 Mil. at 4 A/24V DC, resistive
2 Mil. at 0.2 A/230V DC, resistive
1 Mil. at 0.4 A/24V DC, L/R = 20 ms
1 Mil. at 0.2 A/110V DC, L/R = 20 ms
1 Mil. at 0.1 A/230V DC, L/R = 20 ms
1 LED, combination signal
General Data
2 kVAC/50 Hz test voltage according to VDE 0435
and 6 kV 1.2/50 µs surge voltage according to IEC
947-1 between all inputs and outputs
Performance of following requirements:
Surge capacity of the supply voltage according
to IEC 1000-4-5:
4 kV 1.2/50 µs
Burst according to IEC 1000-4-4:
EMC/Interference Immunity
6 kV 6/50 ns
ESD discharge according to IEC 1000-4-2:
Contact 8 kV, air 8 kV
Electromagnetic HF field according to IEC 8013 and conducted electromagnetic HF signal
according to IEC 801-6: Level 3
Electromagnetic fields according to EN 55 022:
EMC/Emission
class B
Safe Isolation
According to VDE 106, part 101
Insulation Characteristics
➊ Performance Data — See page Important-2, publication A113.
126
Certifications
Standards
56 Cycles (24 h) at 25…40°C and 95% relative
humidity according to IEC 68-2-30 and IEC 68-2-3
4 g in 3 axes at 10…500 Hz, test FC according to
IEC 68-2-6
50 g according to IEC 68-2-27
Enclosure:IP 40
IP 30 (Single-function)
Terminal:IP 20 according to IEC 947-1
100 g
UL, C-UL
Open: –25…+60°C
Enclosed: –25…+45°C
Storage: –40…+85°C
Screw terminal M3.5 for Number 2 Posidrive,
Philips, and slotted screws. Suitable for power
screwdriver. Rated tightening torque 8.8 lb.-in. (0.8
N•m, max. 1.2 N•m).
Dual-chamber system for terminal cross-sections
of 1 x 0.5 mm2…2 x 2.5 mm2 (solid) or stranded 2
x 2.5 mm2 (flexible with sleeve), #20…14 AWG.
Finger protection according to VDE 0106.
Front mounting; For snap-on mounting on 35 mm
DIN Rail or screw fixing by adapter and 2 screws
(M4 type)
Synthetic material without dioxin according to EC/
EFTA notification Number 93/0141/D electrical
contacts with cadmium
cUL Recognized, File E14840, cULus Listed, File
E14840,Guide NKCR,CE Marked (per EU Low
Voltage Directive 73/23 EEC 93/68 EEC: per
Electromagnetic Compatibility Directive 89/336
EEC 92/31 EEC 93/681 EEC)
EN 60947-1,EN 60947-5-1, EN 50081-1, IEC 947,
UL 508, CSA 22.2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement