Zanussi | ZDF 511 | User's Manual | Zanussi ZDF 511 User's Manual

User manual
ZDF 511
Thank you for selecting our
We wish you lots of enjoyment with your new
appliance and we hope that you will consider
our brand again when purchasing household
Please read this user manual carefully and
keep it throughout the product life cycle as a
reference document. The user manual should
be passed on to any future owner of the
Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ 3
"3 in 1 function" _ _ _ _ _ _ _ _ _ _ _ _ _ 18
Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4
Unloading the dishwasher _ _ _ _ _ _ _ _ 19
Washing programmes _ _ _ _ _ _ _ _ _ _ _ 9
Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ 19
First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10
Environmental concerns _ _ _ _ _ _ _ _ _ 21
Set the water softener _ _ _ _ _ _ _ _ _ _ 10
Something not working _ _ _ _ _ _ _ _ _ 22
Filling with dishwasher salt _ _ _ _ _ _ _ 12
Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ 24
Filling with rinse aid _ _ _ _ _ _ _ _ _ _ _ 13
Consumption values _ _ _ _ _ _ _ _ _ _ _ 25
Adjusting the dosage of rinse aid _ _ _ _ 13
Hints for test institutes _ _ _ _ _ _ _ _ _ _ 25
Loading cutlery and dishes _ _ _ _ _ _ _ 14
Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 26
Use of detergent _ _ _ _ _ _ _ _ _ _ _ _ _ 17
Guarantee conditions _ _ _ _ _ _ _ _ _ _ 28
Safety information
In the interest of your safety and to ensure the
correct use, before installing and first using the
appliance, read this user manual carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important
to ensure that all people using the appliance
are thoroughly familiar with its operation and
safety features. Save these instructions and
make sure that they remain with the appliance
if it is moved or sold, so that everyone using it
through its life will be properly informed on appliance use and safety.
Correct use
• This dishwasher is only intended for washing
household utensils suitable for machine
• Do not put any solvents in the dishwasher.
This could cause an explosion.
• Knives and other items with sharp points
must be loaded in the cutlery basket with
their points down or placed in a horizontal
position in the upper basket.
• Only use products (detergent, salt and rinse
aid) suitable for dishwashers.
• Avoid opening the door whilst the appliance
is in operation, hot steam may escape.
• Do not take any dishes out of the dishwasher
before the end of the dishwashing cycle.
• After use, isolate the appliance from the
power supply and turn off the water supply.
• This product should be serviced only by an
authorised service engineer, and only genuine spare parts should be used.
• Under no circumstances should you attempt
to repair the machine yourself. Repairs carried out by inexperienced persons will cause
injury or serious malfunctioning. Contact
your local Service Force Centre. Always insist on genuine spare parts.
General safety
• Dishwasher detergents can cause chemical
burns to eyes, mouth and throat. Could endanger life! Comply with the safety instructions of the dishwasher detergent manufacturer.
• The water in your dishwasher is not for drinking. Detergent residues may still be present
in your machine.
• Ensure that the door of the dishwasher is
always closed when it is not being loaded or
unloaded. In this way you will avoid anybody
tripping over the open door and hurting
• Do not sit or stand on the open door.
Child safety
• This appliance is designed to be operated
by adults. Don’t allow children to use the
dishwasher unsupervised.
• Keep all packaging well away from children.
There is risk of suffocation.
• Keep all detergents in a safe place out of
children’s reach.
• Keep children well away from the dishwasher when the door is open.
• Check your dishwasher for any transport
damage. Never connect a damaged machine. If your dishwasher is damaged contact your supplier.
• All packaging must be removed before use.
• Any electrical and plumbing work required to
install this appliance must be carried out by
a qualified and competent person.
• For safety reasons it is dangerous to alter
the specifications or attempt to modify this
product in any way.
• Never use the dishwasher if the electrical
supply cable and water hoses are damaged;
or if the control panel, work top or plinth area
are damaged such that the inside of the appliance is freely accessible. Contact your
local Service Force centre, in order to avoid
• All sides of the dishwasher must never be
drilled to prevent damage to hydraulic and
electric components.
For electrical and water connection carefully
follow the instructions given in specific paragraphs.
Control panel
On/Off button
Programme selection buttons
Delay start button
Indicator lights
Digital display
Function buttons
Setting mode
Always remember that when performing operations as:
– selecting a washing programme,
– setting the water softener,
– activating/deactivating the rinse aid dispenser
the appliance MUST be in setting mode:
• Press On/Off button, ALL programme selection button lights are illuminated = appliance
in setting mode.
• Press On/Off button, ONLY a programme
button light is illuminated = last performed
programme still set.
In this case the programme has to be cancelled
(see instructions “Cancel a washing programme in progress”).
Function buttons
In addition to the dishwashing programme selection,
the following functions can also be set with the help of
these buttons.
– the setting of the water softener,
– the cancelling of a programme in progress.
– the activation/deactivation of the rinse aid dispenser
Digital display
In the digital display is indicated:
– the level of hardness to which the water softener is
– the approximate remaining time of the running programme,
– activation/deactivation of the rinse aid dispenser,
– the end of the programme (a zero is visible),
– the countdown of the delay start,
– fault codes concerning malfunction of the appliance.
Select the washing programme and the delay
start with the door slightly opened. The start of
the programme or the countdown of the delay
start will occur only after the closure of the door.
Until that moment it is possible to modify the set
Programme selection buttons
• Starting the washing programme:
1. Press the On/Off button.
2. Press the button corresponding to the required
programme, the corresponding light remains illuminated while the other programme lights turn off.
In the digital display will appear, flashing, the running time of the programme (in minutes).
3. The programme in progress light illuminates.
4. Close the dishwasher’s door, the programme will
start automatically. In the digital display the running time of the programme is no longer flashing
and the programme in progress light remains illuminated.
Once the programme has started, if you want to
change the selection made you must cancel the washing programme in progress.
• Cancel the washing programme in progress:
1. Press and hold simultaneously function buttons
B and C until ALL programme button lights will
2. Release function buttons B and C.
3. Switch off the machine by pressing the On/Off
button or select a new washing programme (check
that there is detergent in the detergent dispenser.
This option allows the start of the programme to be
delayed from 1 to 19 hours. After having selected the
washing programme press the delay start button until
the flashing number of the hours for the delay start will
appear in the digital display.
Close the dishwasher’s door, the countdown starts automatically. Once the countdown has elapsed the
washing programme will start automatically.
• Cancel the delay start in progress:
To cancel a delay start in progress you have to reset
the dishwasher; follow the same instructions given in
"Cancel the washing programme in progress".
Delay start button
Cancelling a delay start involves also the cancelling of
the washing programme set. In this case you have to
select the washing programme again.
The selection of the washing programme and
delay start can occur also with the door closed.
Keep in mind that in this way, once a washing
programame button is pressed you have ONLY
3 seconds in which you can choose another
programme or select a delay start, after which
the selected programme will start automatically.
Indicator lights
Programme in progress light
Illuminates when the washing programme has been
When the delay start has been set, this light turns off
and will come on again once the countdown has
elapsed and the washing programme has started.
End of programme light
Illuminates when the washing programme has ended.
3 in 1 light
Indicates the activation/deactivation of the "3 in 1
function" (see "3 in 1 function" ).
Salt refilling light
Illuminates when special salt needs to be filled.
It can remain illuminated several hours after the salt
has been filled.
Rinse aid refilling light
Illuminates when rinse aid needs to be filled.
Washing programmes
Degree of soil
Type of load
Programme description
Intensive 70°
Heavy soil
Crockery, cutlery, pots
and pans
Main wash
2 intermediate rinses
Final rinse
AUTO 65° 50°
Normal / Light soil.
Crockery and cutlery
Main wash
1 or 2 intermediate rinses
Final rinse
Light soil
Crockery and cutlery
Main wash
Final rinse
Normal soil
Crockery and cutlery
Main wash
1 intermediate rinse
Final rinse
30 min.
Rinse and Hold
Partial load (to be completed later in the day).
1 cold rinse (to avoid food
scraps from sticking together).
This programme does not
require the use of detergent.
1) Ideal for washing a partially loaded dishwasher. This is perfect daily programme, made to meet the needs of a family of 4
persons who only wish to load breakfast and dinner crockery and cutlery.
2) Test programme for test institutes.
"Auto" washing programme
During the "Auto" washing programme the
amount of soil on the dishes is determined by
how cloudy the water is.
If the appliance is partially loaded and the
dishes lightly soiled, the "prewash", "main
wash", and "rinse" phases of the programme
are shorter and the water consumption level is
If the appliance is fully loaded and the dishes
heavily soiled, the "prewash", "main wash", and
"rinse" phases of the programme are longer
and the water consumption level is higher.
During the "Auto" programme the temperature
of the main wash water is also automatically
adjusted between 50°C and 65°C depending
on the amount of soil on the dishes.
For this reason the programme duration, water
and energy consumption levels can vary within
the stated range for "Auto" programme (see
"Washing programmes chart").
First use
• Fill the rinse aid dispenser
Before using your dishwasher for the first time:
• Ensure that the electrical and water connections comply with the installation instructions
• Remove all packaging from inside the appliance
• Set the water softener
• Pour 1 litre of water inside the salt container
and then fill with dishwasher salt
If you want to use combi detergent tablets such
as: "3 in 1", "4 in 1", "5 in 1" etc... set the 3 in 1
function (see "3 in 1 function").
Set the water softener
and mmol/l (millimol per litre - international unit
for the hardness of water).
The softener should be adjusted according to
the hardness of the water in your area. Your
local Water Authority can advise you on the
hardness of the water in your area.
The dishwasher is equipped with a water softener designed to remove minerals and salts
from the water supply, which would have a detrimental or adverse effect on the operation of
the appliance.
The higher the content of these minerals and
salts, the harder your water is.
Water hardness is measured in equivalent
scales, Clarke degrees, French degrees (°TH)
Water hardness
Adjusting the water hardness
Use of salt
64 - 88
91 - 125
9,0- 12,5
level 10
53 - 63
76 - 90
7,6 - 8,9
level 9
46 - 52
65 - 75
6,51 - 7,5
level 8
36 - 45
51 - 64
5,1 - 6,4
level 7
28 - 35
40 - 50
4,0 - 5,0
level 6
Water hardness
Adjusting the water hardness
Use of salt
23 - 27
33 - 39
3,3 - 3,9
level 5
18 - 22
26 - 32
2,61 - 3,2
level 4
13 - 17
19 - 25
1,9 - 2,5
level 3
5 - 12
7 - 18
0,71 - 1,8
level 2
< 0,7
level 1
The water softener must be set in both ways:
manually, using the water hardness dial and
Setting the water softener manually (see table)
The water softener is factory set at position 2.
Set switch to position 1 or
Setting the water softener
electronically (see table)
The water softener is factory set at position 5.
1. Press the On/Off button. The dishwasher
must be in setting mode.
2. Simultaneously press and hold function
buttons B and C, until the lights of function
buttons A, B and C start flashing.
3. Press function button A, the lights of function buttons B and C turn off while the light
of function button A goes on flashing. In the
digital display is visible the current level.
displayed = level 5
displayed = level 10
4. To change the level, press function button
A. Each time the button is pressed the level
changes. (For the selection of the new level
see the chart).
if the current level is 5, by pressing function
button A once, level 6 is selected.
if the current level is 10, by pressing function button A once, level 1 is selected.
5. To memorise the operation, switch off the
dishwasher by pressing the On/Off button.
Filling with dishwasher salt
Use only special salt suitable for dishwashers.
Unscrew the cap.
Only before filling with Using the funnel provided,
salt for the first time, fill pour in the salt until the
the salt container with wa- container is filled with salt.
Immediately start a complete programme.
Water will overflow from the container as salt is added.
Remove any trace of salt. Replace the cap tightly
turning it clockwise until it
stops with a click.
Top up the special salt when the light on the
control panel illuminates.
Filling with rinse aid
Open the lid.
Fill up with rinse aid. The Clean up any rinse aid
maximum level for filling is which overflows. Close
the lid and press until it
indicated by "max"
Never fill the rinse aid dispenser with any other sub- Top up the rinse aid when the light on the control panel
stances (e.g. dishwasher cleaning agent, liquid deter- illuminates.
gent). This would damage the appliance.
Adjusting the dosage of rinse aid
Increase the dose if there are drops of water or
lime spots on the dishes after washing.
Open the lid.
Reduce the dose if there are whitish streaks on
the dishes or a bluish film on glassware or knife
Set the dosage level. (The Close the lid and press undose is factory set in po- til it locks.
sition 4).
Loading cutlery and dishes
Sponges, household cloths and any object that
can absorb water may not be washed in the
• Before loading the dishes, you should:
– Remove all left over food and debris.
– Soften remnants of burnt food in pans
• When loading the dishes and cutlery, please
– Dishes and cutlery must not impede the
rotation of the spray arms.
– Load hollow items such as cups, glasses,
pans, etc. with the opening downwards so
that water cannot collect in the container
or a deep base.
– Dishes and items of cutlery must not lie
inside one another, or cover each other.
– To avoid damage to glasses, they must
not touch.
– Lay small objects in the cutlery basket.
• Plastic items and pans with non stick coatings have a tendency to retain water drops;
these items will not dry as well as porcelain
and steel items.
• Light items (plastic bowls etc.) must be loaded in the upper basket and arranged so
they do not move.
For washing in the dishwasher the following cutlery and dishes
are not suitable:
are of limited suitability:
• Cutlery with wooden, horn, china or mother-ofpearls handles.
• Plastic items that are not heat resistant.
• Older cutlery with glued parts that are not temperature resistant.
• Bonded cutlery items or dishes.
• Pewter or copper items.
• Lead crystal glass.
• Steel items prone to rusting.
• Wooden platters.
• Items made from synthetics fibres.
• Only wash stoneware in the dishwasher if it is specially marked as being dishwasher-safe by the manufacturer.
• Glazed patterns may fade if machine washed frequently.
• Silver and aluminium parts have a tendency to discolour during washing: Residues, e.g. egg white,
egg yolk and mustard often cause discolouring and
staining on silver. Therefore always clean left-overs
from silver immediately, if it is not to be washed
straight after use.
Load cutlery. For best results we recommend you
to use the cutlery grid provided (if the size and dimensions of the cutlery
allow it)
Place knives and other
Load the lower basket. Arrange serving dishes and
items of cutlery with sharp large lids around the edge of the basket.
points or edges with their
handles facing upwards.
Risk of injury!
The two rows of prongs on
the lower basket can be
easily lowered to allow
you to load pots, pans and
Load upper basket. Light
items (plastic bowls etc.)
must be loaded in the upper basket and arranged
so they do not move.
For taller items, the cup
racks can be folded upwards.
If plates are to be loaded in the upper basket: load
them starting from the rear positions; tilting them
slightly forwards and avoiding the front positions near
the door.
Adjusting the height of the
upper basket
If washing very large plates you can load them
in the lower basket after moving the upper basket to the higher position.
Maximum height of the dishes in :
upper basket
lower basket
With upper basket raised
20 cm
31 cm
With upper basket lowered
24 cm
27 cm
To move to the higher position proceed as follows:
1. Pull out the basket until it stops.
2. Carefully lift both sides upwards until the mechanism is engaged and the basket is stable.
To lower the basket to the original position proceed
as follows:
1. Pull out the basket until it stops.
2. Carefully lift both sides upwards and then allow the
mechanism to drop back down slowly, keeping
hold of it.
Never lift or lower the basket on one side only
When the basket is in the higher position you
will not be able to use the cup racks.
Use of detergent
Only use detergents suitable for dishwashers.
Open the lid.
Observe the manufacturer’s dosing and storage recommendations.
Fill in the detergent in
compartment A.
Observe the dosing levels.
For programmes with pre- When using detergent
Close the lid.
wash add an additional
tablets: place detergent
detergent dose in comtablets in compartment A.
"3 in 1 function"
This appliance is equipped with the "3 in 1 function", that allows the use of the "3 in 1" combi
detergent tablets.
These products are detergents with a combined
cleaning, rinsing and salt functions. They can
also contain other different agents depending
on which kind of tablets you choose ("3 in 1",
"4 in 1", "5 in 1" etc...)
Check whether these detergents are suitable
for your water hardness. See the manufacturers instructions.
Once this function is selected it will remain active also for the following washing programmes.
With the selection of this function the inflow of
rinse aid and salt from each respective supply
container is automatically deactivated and also
the indicator lights for salt and rinse aid are deactivated.
Select the "3 in 1 function" before the start of a
washing programme.
With the use of the "3 in 1 function", the cycle
durations may change.
Once the programme is running, the "3 in 1
function" can NO longer be changed.
If you want to exclude the "3 in 1 function" you
have to cancel the programme setting and then
deactivate the "3 in 1 function". In this case you
have to set a washing programme (and desired
options) again.
Activation/deactivation of the 3 in 1 function
Press simultaneously the two buttons positioned over the writing 3 in 1, until the "3 in 1
function "indicator light illuminates. This means
that the function is active.
To deactivate the function press the same buttons again until the indicator light corresponding to the "3 in 1" symbol turns off.
If the drying results are not satisfactory we
suggest that you:
1. Fill up the rinse aid dispenser with rinse aid.
2. Activate the rinse aid dispenser.
3. Set the rinse aid dosage to position 2.
• The activation/deactivation of the rinse aid
dispenser can only be possible with the "3 in
1" function active.
Activation/deactivation of the rinse aid dispenser
1. Press the On/Off button. The dishwasher
must be in setting mode.
2. Press simultaneously buttons B and C, until the lights of buttons A , B, and C start
3. Press button B, the lights of buttons A and
C turn off while the light of button B goes
on flashing. The digital display indicates the
current setting:
= Rinse aid dispenser
4. To change the setting, press button B
again, the digital display indicates the new
= Rinse aid dispenser activated.
5. To memorise the operation, switch off the
dishwasher by pressing the On/Off button.
If you decide to turn back to the use of standard
detergent system we advise that you:
1. Deactivate the "3 in 1" function.
2. Fill up the salt container and the rinse aid
dispenser again.
3. Adjust the water hardness setting to the
highest setting and perform 1 normal washing programme without loading any dishes.
4. Adjust the water hardness setting according to the hardness of the water in your
5. Adjust the rinse aid dosage.
Unloading the dishwasher
• Hot dishes are sensitive to knocks.
The dishes should therefore be allowed to
cool down before removing from the appliance.
• Empty the lower basket first and then the
upper one; this will avoid water dripping from
the upper basket onto the dishes in the lower
• Water may appear on the sides and the door
of the dishwasher as the stainless steel will
eventually become cooler than the dishes.
When the washing programme has finished, it
is recommended that the dishwasher is unplugged and the water tap turned off.
Care and cleaning
Cleaning the filters
NEVER use the dishwasher without filters. Incorrect repositioning and fitting of the filters will
produce poor washing results.
Clean filters A, B and C Turn the handle about 1/4 Remove filter A from the
thoroughly under running turn anticlockwise and re- base of the washing comwater.
move filters B and C.
Put the flat filter A back in Replace the filters and
the base of the washing lock by turning the handle
compartment and ensure clockwise to the stop.
that it fits perfectly under
the two guidesD.
Cleaning the spray arms
External cleaning
NEVER try to remove the spray arms.
Clean the external surfaces of the machine and
control panel with a damp soft cloth. If necessary use only neutral detergents. Never use
abrasive products, scouring pads or solvent
(acetone, trichloroethylene etc....).
If residues of soil have clogged the holes in the
spray arms, remove them with a cocktail stick.
Internal cleaning
Ensure that the seals around the door, the detergent and rinse aid dispensers are cleaned
regularly with a damp cloth.
We recommend every 3 months to run the wash
programme for heavy soiled dishes using detergent but without dishes.
Prolonged periods of nonoperation
If you are not using the machine for any prolonged period of time you are advised to:
1. Unplug the appliance and then turn off the
2. Leave the door ajar to prevent the formation of any unpleasant smells.
3. Leave the inside of the machine clean.
able, empty the machine, close the appliance
door, disconnect the water inlet pipe and empty
Moving the machine
If you have to move the machine (moving house
1. Unplug it.
2. Turn the water tap off.
3. Remove the water inlet and discharge hoses.
4. Pull the machine out together with the hoses.
Avoid over tilting the machine during transportation.
Frost precautions
Avoid placing the machine in a location where
the temperature is below 0°C. If this is unavoid-
Environmental concerns
Packaging material
The packaging materials are environmentally
friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<,
>PS<, etc. Please dispose of the packaging
materials in the appropriate container at the
community waste disposal facilities.
When a unit is no longer being used:
• Pull the plug out of the socket.
• Cut off the cable and plug and dispose of
• Dispose of the door catch. This prevents
children from trapping themselves inside
and endangering their lives.
The symbol
on the product or on its packaging indicates that this product may not be
treated as household waste. Instead it should
be taken to the appropriate collection point for
the recycling of electrical and electronic equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative consequences for the environment and
human health, which could otherwise be
caused by inappropriate waste handling of this
product. For more detailed information about
recycling of this product, please contact your
local council, your household waste disposal
service or the shop where you purchased the
Something not working
The dishwasher will not start or stops during
operation. Certain problems are due to the lack
of simple maintenance or oversights, which can
be solved with the help of the indications described in the chart, without calling out an
Fault code and malfunction
Switch off the dishwasher, open the door and
carry out the following suggested corrective actions.
Possible cause and solution
appears in the digital display.
The dishwasher does not fill with water.
• The water tap is blocked or furred with limescale.
Clean the water tap.
• The water tap is turned off. Turn the water tap on.
• The filter (where present) in the threaded hose fitting
at the water inlet valve is blocked.
Clean the filter in the threaded hose.
• The water inlet hose has not been correctly laid or
it is bent or squashed.
Check the water drain hose connection.
appears in the digital display.
The dishwasher will not drain.
• The sink spigot is blocked.
Clean out the sink spigot.
• The water drain hose has not been correctly laid or
it is bent or squashed.
Check the water drain hose connection.
appears in the digital display.
Anti-flood device is activated.
• Close the water tap and contact your local Service
Force Centre.
Fault code and malfunction
The programme does not start.
Once these checks have been carried out;
close the dishwasher’s door and switch on the
appliance. Press the button of the programme
that was running before the intervention of the
alarm. The programme will continue from the
point at which it was interrupted.
If the malfunction or fault code reappears contact the Service Force Centre.
For other fault codes not described in the above
chart, please contact your Service Force Centre.
Contact your local Service Force Centre, quoting the model (Mod.), product number (PNC)
and serial number (S.N.).
Possible cause and solution
• The dishwasher’s door has not been properly
closed. Close the door.
• The main plug is not plugged in. Insert the main plug.
• The fuse has blown out in the household fuse box.
Replace the fuse.
• Delay start has been set.
If dishes are to be washed immediately, cancel the
delay start.
This information can be found on the rating
plate located on the side of the dishwasher
So that you always have these numbers at
hand, we recommend you to make a note of
them here:
Mod. : . . . . . . . . . . . . . . . . . . . . . . .
PNC :. . . . . . . . . . . . . . . . . . . . . . . .
S.N. : . . . . . . . . . . . . . . . . . . . . . . . .
The wash results are not satisfactory
The dishes are not clean
• The wrong washing programme has been selected.
• The dishes are arranged in such a way as to stop
water reaching all parts of the surface. The baskets
must not be overloaded.
• The spray arms do not rotate freely due to incorrect
arrangement of the load.
• The filters in the base of the washing compartment
are dirty or incorrectly positioned.
• Too little or no detergent has been used.
• Where there are limescales deposits on the dishes;
the salt container is empty or the incorrect level of
the water softener has been set.
• The drain hose connection is not correct.
• The salt container cap is not properly closed.
The dishes are wet and dull
• Rinse aid was not used.
• The rinse aid dispenser is empty.
There are streaks, milky spots or a bluish coating on
glasses and dishes
• Decrease rinse aid dosing.
Water drops have dries onto glasses and dishes
• Increase rinse aid dosing.
• The detergent may be the cause. Contact the detergent manufacturer’s consumer care line.
If after all these checks, the problem persists,
contact your local Service Force Centre.
Technical data
Width x Height x Depth (cm)
Electrical connection
Voltage - Overall power - Fuse
Information on the electrical connection is given on the rating plate on the
inner edge of the dishwasher’s door.
Water supply pressure
Minimum - Maximum
0,05 - 0,8
place settings
Max. weight
60,0 x 85,0 x 61,0
Noise level
Consumption values
iations of the power supply and the amount of
The consumption values are intended as a
guide and depends on the pressure and the
temperature of the water and also by the var-
Consumption values
Programme duration (in Energy consumption (in
Water (litres)
Intensive 70°
AUTO 50° 65°
Eat-Load-Run 30 min.
ECO 50° (Test programme for Test Institutes)
Rinse and Hold
* The programme duration is visible in the digital
display when the washing programme is selected.
Hints for test institutes
Testing in accordance with EN 60704 must be
carried out with appliance fully loaded and using the test programme (see "Consumption
Test in accordance with EN 50242 must be
carried out when the salt container and rinse
aid dispenser have been filled with salt and
rinse aid respectively and using the test programme (see "Consumption values").
Full load: 12 standard place settings
Amount of detergent required
5 g + 25 g (Type B)
Full load: 12 standard place settings
Rinse aid setting
Upper basket
position 4 (Type III)
Cutlery basket
Lower basket
cup racks: position A
Any electrical and/or plumbing work required to
install this appliance should be carried out by a
qualified electrician and/or plumber or competent person.
Water connection
The dishwasher must not be connected to open
water appliances or instantaneous water heaters. This dishwasher may be fed with either hot
(max. 60°) or cold water. Nevertheless we advise you a cold water supply.
Only use, for connection to the water mains,
new hose-set; old hose-set must not be reused.
If the machine is connected to new pipes or
pipes which have not been used for a long time,
you should run the water for a few minutes before connecting the inlet hose.
Inlet hose
Connect the inlet hose to a water tap with an external
thread of 3/4”.
The inlet hose can be turned either to the left or the
right to suit the installation by means of the locknut.
The locknut must be correctly fitted to avoid water
Drain hose
Connect drain hose to the Required height: 30 to 100 Ensure that the hoses are When connecting the
sink. Secure it with the
cm above bottom of the
not kinked, crushed or en- drain hose to an under
supplied hose clamp.
sink trap spigot, the entire
plastic membrane (A)
must be removed. Failure to remove all the membrane will result in food
particles building up over
time eventually blocking
the dishwasher drain hose
If you use a drain hose extension the total
length should not be longer than 4 metres.
Likewise the internal diameter of the couplings
used for connections to the waste outlet must
be no smaller than the diameter of the hose
Electrical connection
Safety standards require the appliance to be
Prior to using the appliance for the first time,
ensure that the rated voltage and type of supply
on the rating plate match that of the supply
where the appliance is to be installed.
The fuse rating is also to be found on the rating
Always plug the mains plug into a correctly installed shockproof socket. Multi-way plugs,
connectors and extension cables must not be
This could constitute a fire hazard through overheating.
If necessary, have the domestic wiring system
socket replaced. In case that the electrical ca-
Good levelling is essential for correct closure and
sealing of the door.
When the appliance is correctly levelled, the door will
not catch on either side of the cabinet.
ble has to be replaced, contact your local Service Force centre.
The plug must be accessible after the appliance
has been installed.
Never unplug the appliance by pulling on the
cable. Always pull the plug.
The manufacturer accepts no liability for failure
to observe the above safety precautions.
Fitting under a counter
By removing the dishwasher’s worktop, you can
install it under a close fitting sink unit or a preexisting top.
Be sure that once the appliance has been installed, it is easily accessible for the service
engineer in the event that a repair is required.
Guarantee conditions
Guarantee/Customer Service
Standard guarantee conditions
We, Zanussi-Electrolux , undertake that if within
12 months of the date of the purchase this Zanussi-Electrolux appliance or any part thereof
is proved to be defective by reason only of faulty
workmanship or materials, we will, at our option
repair or replace the same FREE OF CHARGE
for labour, materials or carriage on condition
• The appliance has been correctly installed
and used only on the electricity supply stated
on the rating plate.
• The appliance has been used for normal domestic purposes only, and in accordance
with the manufacturer's instructions.
• The appliance has not been serviced, maintained, repaired, taken apart or tampered
with by any person not authorised by us.
• Electrolux Service Force Centre must undertake all service work under this guarantee
• Any appliance or defective part replaced
shall become the Company's property.
• This guarantee is in addition to your statutory
and other legal rights.
• Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or removable parts
of glass or plastic.
• Costs incurred for calls to put right an appliance which is improperly installed or calls to
appliances outside the United Kingdom.
• Appliances found to be in use within a commercial environment, plus those which are
subject to rental agreements.
• Products of Electrolux manufacturer that are
not marketed by Electrolux
Service and Spare Parts
In the event of your appliance requiring service,
or if you wish to purchase spare parts, please
contact your local Service Force Centre by telephoning
0870 5 929 929
Your telephone call will be automatically routed
to the Service Force Centre covering your postcode area.
For the address of your local Service Force
Centre and further information about Service
Force, please visit the website at
Before calling out an engineer, please ensure
you have read the details under the heading
"Something not working"
When you contact the Service Force Centre
you will need to give the following details:
1. Your name, address and postcode.
2. Your telephone number.
3. Clear concise details of the fault.
4. The model and Serial number of the appliance (found on the rating plate).
5. The purchase date.
Please note a valid purchase receipt or guarantee documentation is required for in guarantee service calls.
Customer Care
For general enquiries concerning your Electrolux appliance, or for further information on Electrolux products please contact our Customer
Care Department by letter or telephone at the
address below or visit our website at
Customer Care Department Electrolux Major
Appliances Addington Way Luton
Bedfordshire, LU4 9QQ Tel: 08705 727 727 (*)
(*) Calls may be recorded for training purposes
European Guarantee
This appliance is guaranteed by Electrolux in
each of the countries listed at the back of this
user manual, for the period specified in the appliance guarantee or otherwise by law. If you
move from one of these countries to another of
the countries listed, the appliance guarantee
will move with you subject to the following qualifications:• The appliance guarantee starts from the
date you first purchased the appliance which
will be evidenced by production of a valid
purchase document issued by the seller of
the appliance.
• The appliance guarantee is for the same period and to the same extent for labour and
parts as exists in your new country of residence for this particular model or range of
• The appliance guarantee is personal to the
original purchaser of the appliance and cannot be transferred to another user.
• The appliance is installed and used in accordance with instructions issued by Electrolux and is only used within the home, i.e.
is not used for commercial purposes.
• The appliance is installed in accordance with
all relevant regulations in force within your
new country of residence.
The provisions of this European Guarantee do
not affect any of the rights granted to you by
+35 5 4 261 450
Rr. Pjeter Bogdani Nr. 7 Tirane
+32 2 363 04 44
Bergensesteenweg 719, 1502
Česká republika
+420 2 61 12 61 12
Budějovická 3, Praha 4, 140 21
+45 70 11 74 00
Sjællandsgade 2, 7000 Fredericia
+49 180 32 26 622
Muggenhofer Str. 135, 90429 Nürnberg
+37 2 66 50 030
Pärnu mnt. 153, 11624 Tallinn
+34 902 11 63 88
Carretera M-300, Km. 29,900 Alcalá de Henares Madrid
Great Britain
+44 8705 929 929
Addington Way, Luton, Bedfordshire LU4 9QQ
+30 23 10 56 19 70
4, Limnou Str., 54627 Thessaloniki
+385 1 63 23 338
Slavonska avenija 3, 10000 Zagreb
+353 1 40 90 753
Long Mile Road Dublin 12
+39 (0) 434 558500 Lino Zanussi, 26 - 33080 Porcia (PN)
+37 17 84 59 34
Kr. Barona iela 130/2, LV-1012, Riga
+370 5 2780609
Ozo 10A, LT 08200 Vilnius
+352 42 431 301
Rue de Bitbourg, 7, L-1273 Hamm
+36 1 252 1773
H-1142 Budapest XIV, Erzsébet
királyné útja 87
+31 17 24 68 300
Vennootsweg 1, 2404 CG - Alphen
aan den Rijn
+47 81 5 30 222
Risløkkvn. 2 , 0508 Oslo
+43 18 66 400
Herziggasse 9, 1230 Wien
+48 22 43 47 300
ul. Kolejowa 5/7, Warszawa
+35 12 14 40 39 39
Quinta da Fonte - Edificio Gonçalves Zarco - Q 35 -2774-518 Paço de Arcos
+40 21 451 20 30
Str. Garii Progresului 2, S4, 040671
Schweiz - Suisse - Svizzera
+41 62 88 99 111
Industriestrasse 10, CH-5506 Mägenwil
+38 61 24 25 731
Gerbičeva ulica 98, 1000 Ljubljana
+421 2 43 33 43 22
Electrolux Slovakia s.r.o., Electrolux Domáce spotrebiče SK, Seberíniho 1, 821 03 Bratislava
+46 (0)771 76 76 76
Electrolux Service, S:t Göransgatan 143, S-105 45 Stockholm
+90 21 22 93 10 25
Tarlabaşı caddesi no : 35 Taksim
+7 495 937 7837
129090 Москва, Олимпийский
проспект, 16, БЦ "Олимпик"
Subject to change without notice
Download PDF