Zanussi | ZUD 9100 F | Instruction Booklet | Zanussi ZUD 9100 F Instruction Booklet

FREEZER
ZUD 9100 F
INSTRUCTION BOOKLET
2222740-62
CONTENTS
Instructions for the User
Instructions for the Installer
Important Safety Instructions
3
Technical Specifications
15
Description of the Appliance
4
Installation
15
Operation
5
Positioning
15
Before use
Freezer controls
Starting your appliance
Temperature control
Warning light (red)
Temperature acoustic alarm
Open door acoustic alarm
Freezing fresh food
Frozen food storage
Internal thermometer
Thawing
Ice making
5
5
5
5
5
5
6
6
6
6
6
6
Electrical Connection
16
Building-in Instructions
17
Grid preparation
Door reversal
Building the appliance in under a worktop
Fitting the plinth
17
17
18
22
Health and Safety Guidelines
7
Defrosting
8
Maintenance and Cleaning
9
Internal cleaning
Periodic cleaning
When the appliance is not in use
9
9
9
Something Not Working?
10
Service and Spare Parts
11
Customer Care Department
11
Zanussi Service Force
12
Guarantee Conditions
14
2
IMPORTANT SAFETY INSTRUCTIONS
These warnings are provided in the interests of your safety. Ensure that you understand them all
before installing or using this appliance. Your safety is of paramount importance.
If you are unsure about any of the meanings of these warnings contact the Customer Care Department.
Prior to Installation
■
General Safety
Check the appliance for transport damage. Under
no circumstance should a damaged appliance be
installed. In the event of damage please contact
your retailer.
■
■
Installation
■
This appliance is heavy. Care should be taken
when moving it.
■
It is dangerous to alter the specifications or
attempt to modify this product in any way.
■
Ensure that the appliance does not stand on the
electrical supply cable.
Important: if the supply cable is damaged, it
must be replaced by a cable available from the
manufacturer or your local Service Force Centre.
Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person.
■
■
■
■
■
■
During Use
Parts which heat up should not be exposed.
Whenever possible, the back of the appliance
should be close to a wall, but leaving the required
distance for ventilation, as stated in the installation instructions.
The appliance should be left for 2 hours after
installation before it is turned on, in order to allow
the refrigerant to settle.
Refrigerant
■
■
■
The refrigerant isobutane (R600a) is contained
within the refrigerant circuit of the appliance, a
natural gas with a high level of environmental
compatibility, which is nevertheless flammable.
During transportation and installation of the appliance, be certain that none of the components of
the refrigerant circuit become damaged.
If the refrigerant circuit should become damaged:
- avoid open flames and sources of ignition.
- thoroughly ventilate the room in which the appliance is situated.
Child Safety
■
■
This appliance contains hydrocarbons in its
cooling unit; maintenance and recharging
must therefore only be carried out by authorised technicians.
Take utmost care when handling your appliance so as not to cause any damages to the
cooling unit with consequent possible fluid
leakages.
The appliance must not be located close to
radiators or boilers.
Avoid prolonged exposure of the appliance to
direct sunlight.
Do not use other electrical appliances (such
as ice cream makers) inside of refrigerating
appliances.
■
This appliance is designed for domestic use only,
specifically for the storage of edible foodstuffs. It
is not intended for commercial or industrial use.
■
Containers with flammable gases or liquids can
leak at low temperatures. Do not store any containers with flammable materials, such as spray
cans, fire extinguisher refill cartridges etc. in the
freezer.
■
Frozen food should not be refrozen once it has
thawed out.
■
Do not place carbonated or fizzy drinks in the
freezer compartment.
■
Ice lollies can cause ‘frost/freezer burns’ if consumed straight from the freezer.
■
Do not remove items from the freezer compartment if your hands are damp/wet, as this could
cause skin abrasions or frost/freezer burns.
■
Bottles and cans must not be placed in the freezer as they can burst when the contents freeze.
■
Manufacturers’ recommended storage times
should be adhered to. Refer to relevant instructions.
Maintenance and Cleaning
Do not allow children to tamper with the controls
or play with the product.
■
There is a risk of suffocation! Keep packaging
material away from children!
3
Before cleaning, always switch off the appliance
and disconnect from the electrical supply.
■
When unplugging always pull the plug from the
mains socket, do not pull on the cable.
Servicing
■
This product should be serviced by an authorised
engineer and only genuine spare parts should be
used.
■
Under no circumstances should you attempt to
repair the appliance yourself. Repairs carried out
by inexperienced persons may cause injury or serious malfunctioning. Contact your local Service
Force Centre.
At the end of the Appliance Life
■
When disposing of your appliance use an authorised disposal site.
■
Remove the plug and ensure that any locks or
catches are removed, to prevent young children
being trapped inside.
DESCRIPTION OF THE APPLIANCE
➀
➁
➂
Freezer calendar
➃
Compartment for freezing
fresh food
➄
➅
Thermometer
Freezer control
Compartment for frozen
food storage
Magnet holder for door
alarm
➃
➄
°C
➀
➃
➂
➂
➁
4
6
5
4
1
2
3
➅
OPERATION
Before use
Remove all securing tapes. Wash inside the appliance
with lukewarm water and bicarbonate of soda
(5 ml to 0.5 litre of water). Do not use soap or detergent as the smell may linger. Dry thoroughly.
Freezer controls
6
5
4
➆ ➅ ➄➃➂ ➁
1
2
3
➀
➀ Thermostat control knob
➁ Push button ON/OFF
➂ Pilot light
➃ Warning light
➄ Fast-freezing indicator light
➅ Push button for fast-freezing and for stopping the audible signal (warning light on)
➆ Symbol for audible alarm (temperature warning and open door warning)
Starting your appliance
Insert the plug into the wall socket. The appliance
can be activated/deactivated by pressing the
ON/OFF button.When the pilot light ➂ is illuminated
this shows that the appliance is on.
To obtain a lower temperature, turn the thermostat
contol knob towards high numbers; to obtain a higher
temperature turn the control knob towards the low
numbers.
Temperature control
Warning light (red)
The temperature within the freezer is controlled by
the thermostat control knob ➀ situated at the bottom
of the cabinet .
To operate the freezer proceed as follows:
Turn the thermostat control knob beyond the «O»
position. When you first start the freezer, we suggest
that you turn the thermostat control knob to a medium setting. For easier turning of this control, use a
small coin. The internal temperature of the freezer is
automatically adjusted by the thermostat to ensure
safe food storage. However, if the appliance is working in unfavourable room conditions such as high
temperature and frequent door openings, it may be
necessary to select a more suitable setting.
If the temperature warning light ➃ lights up, it indicates that the temperature within the freezer has
reached a level where the safe food storage is no
longer ensured.
When the freezer is first switched on, the warning
light will stay on until the temperature has dropped to
a safe level for the storage of frozen food.
Temperature acoustic alarm
This appliance incorporates an alarm which gives off
an audible signal whenever the warning light comes
5
on. This signal can be temporarily stopped by
depressing the push button for fast-freezing ➅.
The fast-freezing push button can be released as
soon as the warning light is off.
Important
Do not put carbonated liquids, (fizzy drinks
etc.), in the freezer compartment.
Ice lollies, if consumed immediately after
removal from the freezer, can possibly result
in a low temperature skin burn.
Do not remove items from the freezer if your
hands are damp/wet, as this could cause skin
abrasions or "frost/freezer burns".
If there is a power failure during the storage of
frozen food, do not open the door during the
whole time of the power failure. If the freezer
is fully loaded, the frozen food will not be
affected if the power cut is of short duration;
otherwise, it is recommended to consume the
food within a very short time.
Open door acoustic alarm
This appliance also incorporates an alarm which
sounds if the door is left open for more than 60 seconds. The signal will be stopped when the door is
closed again.
Freezing fresh food
In any 24 hour period you can freeze up to 18 kg of
fresh food.
Activate fast freeze by depressing the fast-freeze
switch ➅ 24 hours before you want to freeze your
fresh food, the yellow light ➄ illuminates. This time
can be shortened, depending on the quantity of food
to be frozen. After the time has elapsed place the
food to be frozen in the two top compartments of the
freezer as this is the coldest part; if freezing only a
small amount of food, always use the top compartment.
Once the food is completely frozen (which could take
up to 24 hours) press the fast freeze switch to deactivate the fast freeze mode; the yellow light ➄ goes
off.
Distribute the frozen food packages in the other compartments, so that the top compartments can be
used for a further freezing operation.
Only freeze top quality, fresh and thoroughly cleaned
foodstuffs.
Do not allow fresh food to touch food which is
already frozen.
During the freezing process, ensure that the freezer
door remains closed.
Internal thermometer
This indicates the internal temperature of the freezer. It may indicate a temperature above -18°C when
large quantities of food are placed inside for freezing
or when the door is left open for a long time.
°C
PR202
Thawing
Frozen food, prior to being used, can be thawed in
the fridge or at room temperature depending on the
time available. Small food items may even be
cooked from frozen; in this case cooking will take
longer. Any frozen food which is allowed to thaw
accidentally should either be eaten as soon as possible or thrown away. Alternatively, if the food is
uncooked and has not been completely defrosted it
can be cooked and then refrozen.
Defrosted cooked food must never be refrozen.
Frozen food storage
When you first start the freezer or if the freezer has
been out of use for some time, we advise you to run
your appliance for at least two hours in the «fast
freeze» mode before storing frozen food.
To obtain the best performance from this appliance,
we strongly recommend that you make sure that the
commercially frozen foodstuffs were adequately
stored by the retailer and, furthermore, be sure that
these frozen foodstuffs are transferred from the foodstore to the consumer in the shortest possible time (a
temperature increase of the frozen food could shorten its storage period).
It is also advisable not to exceed the storage period
indicated by the producer of the food.
Finally, do not open the door frequently or leave it
open longer than is absolutely necessary.
Ice making
Fill each compartment of the ice tray 3/4full with
water and place it in the freezer. To release the ice
cubes, twist the tray along its length. Never use a
sharp instrument to remove ice from the tray.
6
HEALTH AND SAFETY GUIDELINES
Because of consumer demand, preservatives have been removed from many pre-prepared foods. This
together with the changes in shopping habits to a once-a-week shop, mean that safe handling and
storage of food is even more important than ever.
The following tips should help you to ensure that the food in your home is in as perfect condition as
possible.
■
Keep the freezer door closed as much as possible.
■
Do not push food together too much, try to allow
air to circulate around each item.
■
Cool cooked food as quickly as possible but do
NOT place in the freezer until cool. (Leave food
in a place as cool as possible in order that it can
then be placed in the refrigerator as soon as possible).
■
Do not store food uncovered.
■
The best way to defrost food is to put it in the
refrigerator to thaw slowly.
■
Ensure that food placed in the freezer is dated
and labelled and used in date order to ensure
that food is consumed at its best.
■
It is important that food is used before its “best
before” date.
■
Always wash your hands with soapy water and
dry them with a clean towel before handling food.
■
Keep work surfaces clean and avoid cross contamination by not using the same work surface or
knife, without washing them thoroughly in
between.
■
The foods to be frozen must be fresh and of the
best quality.
■
The size of each pack should be small enough to
ensure that it is used in one go. Small packs
freeze more quickly and uniformly and give better
results.
■
Frozen food, once thawed, must not be refrozen.
Lean food keeps better and longer than fatty
food, salt reduces the storage time.
■
Wrap the food in polythene or aluminium freezing
bags or foil so that they adhere to the food and
provide an airtight seal.
■
Packaging which is swollen or has traces of
refrozen water droplets on the pack could indicate that the product has not been kept at a suitable temperature and that it may have lost its
original quality. Partially thawed food must not be
refrozen, it must be consumed within 24 hours.
Never exceed the storage time indicated.
7
■
Never place hot food, bottles or cans of fizzy
drink in the freezer as they may explode.
Containers with a lid must not be filled to the
brim.
■
Do not open the door or place extra fresh food in
the freezer next to food which is already frozen
as this could cause the temperature of the frozen
food to rise and its quality and storage life to
reduce.
DEFROSTING
The freezer compartment will become progressively
covered with frost. This should be removed with the
special plastic scraper provided, whenever the thickness of the frost exceeds 1/4".
Important
In the event of a power failure causing the
temperature within your freezer to rise, do
not re-freeze the food without checking its
condition. The following guidelines should
assist you:
During this operation it is not necessary to switch off
the power supply or to remove the foodstuffs.
However, when the ice becomes very thick on the
inner liner, complete defrosting should be carried out
and it is advisable to carry out this operation when
the appliance is empty.
To carry out complete defrosting proceed as follows:
Ice-cream: once thawed should be discarded.
Fruits & Vegetables: if soft should be cooked
and used up.
Breads & Cakes: can be re-frozen without
danger.
Shellfish: should be refrigerated and used up
quickly.
Cooked Dishes: i.e. casseroles should be
refrigerated and used up.
Large Pieces of Meat: can be re-frozen providing there are still ice crystals remaining
within them.
Small Joints: should be cooked and can then
be re-frozen as cooked dishes.
Chicken: should also be cooked and refrozen as a cooked dish.
1. Remove any stored food, wrap it in several layers
of newspaper and put it in a cool place.
2. Turn the thermostat control ➀ to the «O» setting.
3. Leave the door open.
4. Remove the three large drawers.
5. When defrosting is completed, remove the water
that has collected in the small bottom drawer and
dry the interior thoroughly.
Turn the thermostat control to a medium setting and,
after letting the appliance run for at least two hours
in the «fast freeze» mode, replace the previously
removed food into the compartments.
Important
A temperature rise of the frozen food packs
during defrosting may shorten their storage
life.
Never use sharp metal tools to scrape off
frost from the evaporator as you could damage the appliance beyond repair.
8
MAINTENANCE AND CLEANING
Before any maintenance or cleaning work is carried
out, DISCONNECT the appliance from the ELECTRICITY supply.
Warning
This appliance contains hydrocarbons in its
cooling unit maintenance and recharging must
therefore only be carried out by authorised
technicians.
Internal cleaning
Clean the inside and accessories with warm water
and bicarbonate of soda (5ml to 0.5 litre of water).
Rinse and dry thoroughly.
NEVER USE DETERGENTS, ABRASIVE POWDERS, HIGHLY PERFUMED CLEANING PRODUCTS OR WAX POLISHES, TO CLEAN THE INTERIOR AS THESE WILL DAMAGE THE SURFACE AND
LEAVE A STRONG SMELL.
Important
Do not use abrasive products.
Periodic cleaning
The appliance is equipped with a ventilation grid.
Keep clean to guarantee good ventilation and good
working order of the appliance.
An accumulation of dust will affect the performance of
the appliance and cause excessive electricity consumption.
The structure of the appliance permits cleaning of the
rear zone close to the wall, using a vacuum cleaner.
1. Remove the plinth (1), then the ventilation grid (2);
2. Carefully pull the air deflector out (3).
3
S.I.013
When the appliance is not in use
When the appliance is not in use for long periods, disconnect from the electricity supply, empty all foods
and clean the appliance, leaving the door ajar to prevent unpleasant smells.
9
2
1
SOMETHING NOT WORKING?
Before contacting your local Service Force Centre check the following points.
IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation, a charge will be made even if the appliance is under guarantee.
Symptom
Solution
No power to the appliance
- Check there is power at the socket.
- Check there is not a power cut by checking the
household lights.
- Check the fuse has not blown.
The temperature in the freezer is too high
- Check the thermostat control knob is turned to the correct setting relative to ambient conditions.
- Check the ambient temperature is within the appliances
operating limits of 10°C to 38°C.
The freezer door will not open
- Has door just been opened?
- If so leave for a few minutes to allow the air pressure to
equalise.
The compressor runs continuously
- Adjust the thermostat control knob to give correct
temperature control. See page 5.
- Check that the door is closed.
- Large quantities of food have recently been placed in
the cabinet and/or door is frequently opened.
- Check that air ventilation is not obstructed.
Excessive frost and ice has built up.
- Ensure the door is not left opened.
- Check that nothing is preventing the door from closing.
- Is the door gasket intact and clean.
- Has advised periodic defrosting been carried out.
Noise
- Refer to normal operating sounds.
If after the above checks, there is still a fault, call your local Service Force Centre.
In-guarantee customers should ensure that the above checks have been made as the engineer will make a
charge if the fault is not a mechanical or electrical breakdown.
Please note that proof of purchase is required for any in-guarantee service calls.
10
SERVICE AND SPARE PARTS
Before calling out an engineer, please ensure you
have read the details under the heading ‘Something
Not Working?’
When you contact the Service Centre you will need
to give the following details.
In the event of your appliance requiring service, or if
you wish to purchase spare parts please contact
your local Zanussi Service Force Centre by
telephoning:
0870 5 929929
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model serial no. of the appliance (found on
the rating plate)
5. The purchase date
Your call will be automatically routed to the Service
Force Centre covering your post code area. The
address of your local Service Force Centre is
detailed on the following pages.
CUSTOMER CARE DEPARTMENT
For general enquiries concerning your Zanussi appliance or for further information on Zanussi products, you
are invited to contact our Customer Care Department by letter or telephone or visit our website at
www.zanussi.co.uk
Customer Care Department
Zanussi
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel: 08705 727727 (*)
(*) calls to this number may be recorded for training purposes.
11
12
13
GUARANTEE CONDITIONS
Standard guarantee conditions
We, Zanussi, undertake that if within 24 months of the date of purchase this Zanussi appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or
replace the same FREE OF CHARGE for labour, materials or carriage on condition that:
■
The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
■
The appliance has been used for normal domestic purposes only, and in accordance with the manufactuer's
instructions.
■
The appliance has not been serviced, maintained repaired, taken apart or tampered with by any person not
authorized by us.
■
All service work under this guarantee must be undertaken by a Zanussi Service Force Centre.
■
Any appliance or defective part replaced shall become the Company's property.
■
This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
■
Damage or calls resulting from transportation, improper use or neglect, thc replacement of any light bulbs or
removable parts of glass or plastic.
■
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside
the United Kingdom.
■
Appliances found to be in use within a commercial environment, plus those which are subject to rental
agreements.
■
Products of Zanussi manufacture which are not marketed by Zanussi.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home
subject to the following qualifications:
■
The guarantee starts from the date you first purchased your product.
■
The guarantee is for the same period and to the same extent for labour and parts as exists in the new
country of use for this brand or range of products.
■
This guarantee relates to you and cannot be transferred to another user.
■
Your new home is within European Community (EC) or European Free Trade Area.
■
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household.
■
The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service Organisation is aware of your move and able to look
after you and your appliance.
France
Germany
Italy
Sweden
UK
Senlis
Nurenberg
Pordenone
Stockholm
Slough
+33
+49
+39
+46
+44
(0)
(0)
(0)
(0)
(0)
44 62 29 99
911 323 2600
1678 47053
8 738 79 50
1753 219897
14
TECHNICAL SPECIFICATIONS
DIMENSIONS
Height
Width
Depth
81,5
59,6
54
POWER SUPPLY VOLTAGE AND FREQUENCY
TOTAL POWER ABSORBED
AVERAGE DAILY UNITS ELECTRICITY(*)
220-240 V / 50 Hz
90 W
0,72 kWh
GROSS CAPACITY
108 l
NET CAPACITY
100 l
cm
cm
cm
STAR RATING
(*)This figure is based on standard test results in accordance with European Standard EN153. Actual consumption will depend on how the appliance is used and where it is located.
INSTALLATION
Positioning
This appliance should only be installed at a location
where the ambient temperature corresponds to the
climate classification indicated on the rating plate,
which is located on the inside left of the appliance.
The following table shows which ambient temperature
is correct for each climate classification.
SN
+10°C to +32°C
ST
+18°C to +38°C
The appliance should be located in a dry atmosphere,
out of direct sunlight and away from continuous heat
and extreme temperature, e.g. not next to a boiler or
radiator, or in a very cold room e.g. an outhouse. If
these temperatures are exceeded i.e. warmer or colder, then the appliance may not operate correctly.
For building-in and door reversal instructions please
refer to the relevant instructions on the following
pages.
15
ELECTRICAL CONNECTION
This appliance complies with the E.E.C. Directive
No. 87/308 of 2.6.87 relative to radio interference
suppression.
WARNING:
THIS APPLIANCE MUST BE EARTHED.
The manufacturer declines any liability
should this safety measure not be
observed.
If the plug that is fitted to your appliance is not suitable for your socket outlet, it must be cut off and the
appropriate plug fitted.
Remove the fuse from the cut off plug.
The cut off plug should then be disposed of to prevent the hazard of shocks in case it should be
plugged into a 13amp socket in another part of your
home.
This appliance complies with the following
E.E.C. Directive:
- 73/23 EEC of 19.2.73 (Low Voltage Directive)
and subsequent amendments.
- 89/336 EEC of 3.5.89 (Electromagnetic
- Compatibility Directive) and subsequent amendments.
Please ensure that when the appliance is
installed it is easily accessible for the engineer
in the event of breakdown.
Important
The wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow
Blue
Brown
- Earth
- Neutral
- Live
If you fit your own plug, the colours of the wires in
the mains lead of your appliance, may not correspond with the markings identifying the terminals in
your plug, proceed as follows:
Connect the Green and the Yellow (earth) wire to the
terminal in the plug which is marked with the letter
«E» or the earth symbol
, or coloured green and
yellow.
13 AMP. FUSE
13 AMP
GREEN & YELLOW
Connect the blue (neutral) wire to the terminal in the
plug which is marked with the letter «N» or coloured
black.
BROWN
BLUE
Connect the brown (live) wire to the terminal in the
plug which is marked with the letter «L» or coloured
red.
D207
The plug moulded onto the lead incorporates a fuse.
For replacement, use a 13amp BS1362 fuse. Only
ASTA or BSI approved fuses should be used.
The plug must not be used if the fuse cover/carrier is
lost. The cover/carrier is indicated by the coloured
insert at the base of the plug.
A replacement cover/carrier must be obtained from
your local Zanussi Service Force Centre.
16
CORD CLAMP
BUILDING-IN INSTRUCTIONS
Before carrying out any work, remove the plug from
the power socket.
Grid preparation
Left door opening:
A
Remove the left side (A) of the grid cutting it from the
rear (see figure).
B
Right door opening:
Remove the right side (B) of the grid cutting it from
the rear (see figure).
DO002/2
To position the grid on the appliance proceed as follows:
Apply the grid to the base of the appliance by pushing
on to the clasps (a) until they click.
a
a
DO001
Door reversal
To reverse the opening direction of the door, proceed
as shown in the figures:
6
4
1
7
8
5
2
3
1
2
17
Attention
After completion of the door reversing operation, check that the door gasket adheres to the
cabinet. If the ambient temperature is cold (i.e.
in Winter), the gasket may not fit perfectly to
the cabinet. In that case, wait for the natural fitting of the gasket or accelerate this process by
heating up the part involved with a normal
hairdryer on a low setting.
10
13
9
12
11
3
Building in the appliance under a worktop
1. The dimensions of the recessed installation area
must correspond with those indicated in the figure.
60
0
5
min50
.
600
DO013
2. Installation kit
1xB
2xC
1xA
12
1
18
2
1
2
1
2
3. Two cabinet securing brackets are supplied with
the installation pack. They need to be assembled
onto the cabinet prior to cabinet being pushed into
the Kitchen aperture.
- To fit these brackets remove the two screws at the
top left and right hand front corners of the cabinet.
- Position the two brackets as shown in the figure
and replace the two securing screws.
Right hand
bracket
Left hand
bracket
4. Push the appliance into place. The plug socket
necessary for connection of the appliance to the
electricity supply should be positioned, so that the
plug is not placed in the recess.
596
5. To adjust the height proceed as follows:
- Loosen or tighten the two front feet.
- The rear feet are adjusted by turning the screw in
the front kick plate to the left or right.
5
55 x
ma
-
2Li89
+
6. If necessary, pads are supplied for the rear feet to
make sliding the appliance in and out of the recess
easier. To fit the pads, press them onto the rear
feet.
If required, the dimensions of these pads can be
reduced by breaking them where marked.
II52
2
1
B
115°
3
4
N.B. The joint cover (B) is to be assembled after having installed the appliance in the recess.
19
7. Screw appliance into place and retain the cabinet
with screws through the securing brackets into the
worktop or adjacent woodwork as necessary.
5
8. To mount the furniture door proceed as shown in
the figures:
2
1
a
10
C
4
3
b
6
a
b
C
clic
C
clic
7
8
20
c
UPPER PART OF KITCHEN FURNITURE PANEL
1
a
=
=
LOWER PART OF KITCHEN FURNITURE PANEL
2
275
275
x
ma
b
9
1
45
°
9/a
2
=
3
10
=
11
10
12
21
100
9. Refit the covering strip.
A
13
Fitting the plinth
Important
For the efficient operation of the appliance, it is
important that the original ventilation grid is
used.
■
Important
The plinth must be positioned at a minimun distance of 25 mm from the door.
22
a = 100
b = 150
■
For an opening height dimension A=820 mm and a
plinth height dimension a=100 mm, the plinth may
be fitted without adjustments. The same applies to
an opening height dimension B=870 mm and a
plinth height dimension b=150 mm.
For plinth heights greater than a=100 mm, b=150
mm, a cut should be made in the plinth, 580 mm
wide, in the centre of the appliance position, leaving a remaining height of a=100 mm, b=150 mm.
Attach plinth to the kitchen units.
A = 820
B = 870
■
580
25
25
DO008
- 80
© Electrolux Household Appliances Limited 2000
Download PDF

advertising