Zanussi | ZWD 1260 W | Instruction Booklet | Zanussi ZWD 1260 W Instruction Booklet

WASHER-DRYER
ZWD 1260 W
DRYING
FAST COLOUREDS
NON FAST COLOUREDS
WHITES + PREWASH
WHITES
RINSES
FRESHEN UP G
STORE DRY
Kg 2.5 80'
Kg 1 50'
SPIN
132989210
C
D
A
B
F
H
IRON DRY
Kg 2.5 60'
Kg 1 40'
ESSENTIAL
J
J
MIXED FABRICS
WOOL
WORN ONCE
DELICATES
RINSES
SHORT SPIN M
DRAIN
STORE DRY SYNTHETICS
Kg 1.5 100'
70'
Kg 1
K
P
L
Q
R
S
VA R I A B L E
SPIN
DRY
ON-OFF
PROGRAMME
ZWD 1260 W
HALF
LOAD
N
N
1200
INSTRUCTION BOOKLET
GB
Important Safety Information
It is most important that this instruction book should be retained with the appliance for future
reference. Should the appliance be sold or transferred to another owner, or should you move
house and leave the appliance, always ensure that the book is supplied with the appliance in
order that the new owner can get to know the functioning of the appliance and the relevant
warnings.
These warnings have been provided in the interest of safety. You MUST read them carefully
before installing or using the appliance.
Installation
●
●
●
●
●
●
●
This appliance is heavy. Care should be taken when
moving it.
It is dangerous to alter the specifications or attempt
to modify this product in any way.
All packing and transit bolts must be removed before
use. Serious damage can occur to the product and to
property if this is not adhered to. See relevant section
in instructions.
Any plumbing work required to install this appliance
should be carried out by a qualified plumber or
competent person.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
Care must be taken to ensure that the appliance does
not stand on the electrical supply cable.
If the machine is situated on a carpeted floor, please
adjust the feet in order to allow air to circulate freely.
●
●
●
●
●
Child Safety
●
●
●
●
●
This appliance is designed to be operated by adults.
Children should not be allowed to tamper with the
controls or play with the product.
Pets and children have been known to climb into
washer-dryers. Please check your drum before use.
The glass door becomes very hot during the washing
and drying cycle. Keep children away from the
vicinity of the appliance whilst it is in operation.
Keep all packaging well away from children.
Keep all detergents in a safe place out of children’s
reach.
●
●
●
Use
●
●
●
●
Always unplug the appliance and turn off the water
supply after use.
Do not overload the appliance. See relevant section
in the instruction book.
Only wash and dry fabrics which are designed to be
machine washed and dried. If in doubt, consult the
care label on the clothes.
Before washing, ensure that all pockets are empty
and buttons and zips are fastened. Avoid washing
●
●
2
frayed or torn articles and treat stains such as paint,
ink, rust, and grass before washing. Underwired bras
must NOT be machine washed.
Any objects such as coins, safety pins, nails, screws,
stones or any other hard, sharp material can cause
extensive damage and must not be placed into the
machine.
Garments which have been in contact with volatile
petroleum products should not be machine washed.
If volatile cleaning fluids are used, care should be
taken to ensure that the fluid is removed from the
garment before placing in the machine.
Wash small items such as socks, laces, washable
belts etc in a washing bag or pillow case as it is
possible for such items to slip down between the tub
and the inner drum.
Only use the advised quantities of fabric softener.
Damage to the fabric can ensue if you over-fill.
Refer to the manufacturer’s recommendations of
quantities.
As some duvets and eiderdowns should be
washed/dried in large commercial machines because
of their bulk, please check with the manufacturer of
the item before washing in a domestic machine.
The users should always check that they have not
left their gas lighters (disposable or otherwise) in
their clothing.
Never tumble dry items that have had contact with
chemicals such as dry cleaning fluid.These are of a
volatile nature and could cause an explosion.
Only tumble dry items which have been washed in
water or require airing.
Plastic detergent dispensers should not remain in the
drum during the drying cycle, as the plastic used is
not designed to withstand the heat. If you wish to
wash-through-to-dry you should use the
conventional detergent dispenser drawer.
Leave the porthole door slightly ajar between washes
to preserve the door seal.
Under no circumstances should you attempt to repair
the machine yourself. Repairs carried out by
inexperienced persons may cause injury or serious
malfunctioning. Contact your local Service Force
Centre. Always insist on genuine spare parts.
Contents
For the User
Washing and Drying Hints
Your New Washer-Dryer
Important Safety Information
Description of the Appliance
Detergent dispenser drawer
The Control Panel
Operating Sequence
Which detergent to use?....
And in which form?
Fabric Conditioners
4
2
Wash Care Symbols
Washing Programmes
Drying Programmes
Maintenance and Cleaning
5
5
6
Washing 5 kg of white cotton at 95°C
Load the laundry
Measure out the detergent
Measure out the fabric softener
Select the spin speed or option
or
Select the required programme
Start the machine
At the end of the programme
Washing 2.5 kg of mixed fabrics at 50°C
Load the laundry
Measure out the detergent
Measure out the fabric softener
Select the spin speed or option
or
Select the programme
Start the machine
At the end of the programme
Drying 2.5 kg of cotton
Load the laundry
Select the programme
Select the required time
Start the machine
At the end of the programme
Autodrying 1 kg of mixed fabrics
Load the laundry
Add the washing powder and additive
Select the programme
Select the required time
Start the machine
At the end of the programme
7-11
7
7
7
7
7
7
8
8
8
8
8
8
9
9
9
9
10
10
10
10
10
10
11
11
11
11
11
11
11
Descaling
After each wash
Maintenance wash
External cleaning
Cleaning the dispenser drawer
Cleaning the drawer recess
Cleaning the filter
The dangers of freezing
Something Not Working
Service and Spare Parts
Guarantee Conditions
12
13
13
13
14
15-16
17
18-19
18
18
18
18
18
18
18-19
19
20-21
21
22
For the Installer
Installation Instructions
Technical Specifications
Unpacking
Positioning
Water inlet
Water drainage
Levelling
Special conditions
In the interest of the environment
Electrical connection
Guide to use the Instruction Book
The following symbols will be found in the text to guide you throughout the instructions:
Safety instructions
Hints and tips
Environmental information
3
23
23
24
24
25
25-26
26
26
26
27
Your New Washer-Dryer
Your new washer-dryer meets all modern requirements for effective treatment of laundry with
low water, energy and detergent consumption.
It is gentle with your laundry, simple to use and easy to care for.
●
●
●
●
The special wool programme with its new delicate
wash system treats your woollens with extreme care.
The balance control ensures that the machine
remains stable when spinning.
Automatic cooling of the wash water to 60°C
before draining, with the 95°C programme. This
reduces thermal shock to fabrics, helping to prevent
creasing.
The two drying programmes will give your wash
that soft, relaxed feel whatever the weather.
In the interest
of the environment
●
●
●
Ecological hints
●
To save water and energy and help protect the
environment, we recommend that you follow these
hints:
● Adjust the quantity of detergent according to the
hardness of your water supply, the amount of
laundry and the degree of soiling.
● A programme without prewash is sufficient for
normally soiled laundry.
● Try to load the maximum drying capacity of the
machine as small loads are uneconomical.
● Always load well spun laundry. The higher the spin
speed, the lower the electricity consumption and the
shorter the drying times.
Materials marked with the symbol
are
recyclable.
Check with your local Council or Environmental
Health Office to see if there are facilities in your area
for re-cycling this appliance.
When the appliance is to be scrapped, cut off the
power supply cable and make the door lock device
unusable to prevent young children from being
trapped inside.
Help to keep your country tidy - use authorised
disposal sites for your old appliance.
How do we help to protect the environment?
We use recycled paper!
Important
Your machine is fitted with a balance control device, which ensures the machine is stable during the spin.
If the wash load appears not to have been spun sufficiently at the end of the wash cycle, because it is not evenly
distributed in the drum, the balance control device may have operated. It will therefore be necessary to redistribute the
wash load manually and select a spin programme. For more detailed information see the section headed "Something
Not Working".
4
Description of the Appliance
1 Detergent dispenser drawer
2 Programme guide
3 Drying time selector dial
4 Drying indicator light
5 “Mains-on” light
6 ON-OFF button
7 HALF LOAD button
8 Spin Speed selector dial
9 Programme selector dial
10 Door opening handle
11 Filter
12 Adjustable feet
5
34
1
8
DRYING
FAST COLOUREDS
NON FAST COLOUREDS
WHITES + PREWASH
WHITES
RINSES
FRESHEN UP G
STORE DRY
Kg 2.5 80'
Kg 1 50'
SPIN
C
D
A
B
F
H
IRON DRY
Kg 2.5 60'
Kg 1 40'
ESSENTIAL
J
J
MIXED FABRICS
WOOL
WORN ONCE
DELICATES
RINSES
SHORT SPIN M
DRAIN
STORE DRY SYNTHETICS
Kg 1.5 100'
70'
Kg 1
K
P
L
Q
R
S
VA R I A B L E
SPIN
DRY
ON-OFF
9
PROGRAMME
ZWD 1260 W
HALF
LOAD
N
N
1200
2
67
10
11
12
Detergent dispenser drawer
Prewash
Main wash
Fabric softener
C0063
5
The Control Panel
DRYING
FAST COLOUREDS
NON FAST COLOUREDS
WHITES + PREWASH
WHITES
RINSES
FRESHEN UP G
STORE DRY
Kg 2.5 80'
Kg 1 50'
C
D
A
B
F
SPIN H
IRON DRY
Kg 2.5 60'
Kg 1 40'
ESSENTIAL
MIXED FABRICS
WOOL
WORN ONCE
DELICATES
RINSES
SHORT SPIN M
K
P
L
Q
R
DRAIN S
STORE DRY SYNTHETICS
Kg 1.5 100'
70'
Kg 1
J
J
DRY
ON-OFF
VA R I A B L E
SPIN
PROGRAMME
7
8
ZWD 1260 W
HALF
LOAD
N
N
1200
1
2
3 45 6
7 Spin speed selector dial
1 Programme guide
This dial allows you to select the desired spin speed or
the following options:
●
= no spin. All the spinning phases are excluded.
To be used for items that tend to crease. If position
is selected for cotton items (programmes 95°,
60° and 40°), the machine will perform an extra
rinse (4 instead of 3).
●
= Rinse Hold. The water of the last rinse is not
emptied out to prevent any creasing in the clothes if
they are left damp in the drum.
If you select the Rinse Hold option
in an
automatic washing & drying programme the
machine will not dry.
We recommend you not to select a lower spin speed
so as to avoid a too long drying time when carrying
out the automatic washing & drying programme.
The spin speeds on the dial refer to cotton programmes.
For mixed fabrics and wool, position 1200 corresponds
to 850, for delicates 650 rpm.
Position 450 corresponds to 350 rpm for delicates.
2 Drying time selector dial
Graduated up to 120 mins for cottons (light blue
section) and synthetics (green section), this dial allows
you to select the desired drying time according to the
type and quantity of laundry and the required degree of
dryness.
Turn the dial clockwise only.
Cooling phase
To allow the laundry to cool down, a cooling phase
starts automatically 10 minutes before the end of drying
and this phase must in no circumstances be reduced or
interrupted.
3 Drying indicator light
This light illuminates when the machine is drying.
4 Mains-on light
This light illuminates when the machine starts working
and goes out when the ON-OFF button is released.
8 Programme selector dial
5 ON-OFF button
Turn the dial clockwise to select the required wash and
drying programme.
Before setting the dial to any position ensure that the
machine is switched off.
By depressing this button the machine starts operating.
When depressed again, the machine stops.
6 HALF LOAD button
Select this button to reduce water consumption on the
rinse cycle when washing a smaller load of cottons or
linens (maximum load size = 2.5 kg).
6
Operating Sequence
3. Measure out the fabric
softener
Before the first wash, we recommend that you run a
cotton cycle at 60°C, without any laundry in the
machine, to remove any manufacturing residue from the
drum and tub.
Pour 1/2 a measure of detergent into the main wash
compartment
of the dispenser drawer and start the
machine.
If required, pour fabric softener into the compartment
marked
(the amount used must not exceed the
“MAX” mark in the drawer).
Close the drawer gently.
WASHING 5 KG OF WHITE COTTON AT 95°C
Suppose you have 5 kg of normally soiled laundry to
wash. It is white cotton and is suitable for high
temperature washing.
1. Load the laundry
C0065
Open the door by pulling the door handle outwards.
Place the laundry in the drum, one item at a time,
shaking them out as much as possible. Close the door.
4. Select the spin speed or option
or
450
Turn the dial to the required position.
550
1200
10
P0004
850
65
0
00
750
2. Measure out the detergent
5. Select the required programme
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent required and pour
it into the main wash compartment .
If you wish to carry out the prewash, pour detergent into
the compartment marked .
Turn the programme selector dial clockwise to the
programme B or A (if you wish to perform a prewash).
B
P1006S
C0064
7
6. Start the machine
WASHING 2.5 KG OF MIXED FABRICS AT 50°C
Suppose you have 2.5 kg of Mixed fabrics to wash.
They are rather delicate fabrics and should not be
washed at a high temperature.
Before starting the machine check that:
● the appliance is plugged in
● the water supply taps are turned on
● the drain hose is correctly and securely positioned
● the door and the detergent dispenser drawer are
closed.
Depress the ON-OFF button: the mains-on light will
illuminate and the machine starts operating.
1. Load the laundry
Open the door by pulling the door handle outwards.
Place the laundry in the drum, one item at a time,
shaking them out as much as possible. Close the door.
ON-OFF
P0004
T0001S
7. At the end of the programme
2. Measure out the detergent
The machine stops automatically.
If you have selected the RINSE HOLD option
, the
machine will stop with the water of the last
rinse left in the tub, to prevent the fabric from creasing.
To drain only, select position
or the drain
programme “S”.
To drain and spin, select programme “H” or turn the
spin speed selector dial to the desired speed position: the
machine will spin at the selected speed .
The door is controlled by a safety device which releases
2 minutes after the end of the programme.
Switch the machine off by depressing the ON-OFF
button again. The mains-on light goes out.
When the programme has finished you are advised to
unplug the appliance and turn off the water taps.
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent required and pour
it into the main wash compartment .
C0064
3. Measure out the fabric
softener
If required, pour fabric softener into the compartment
marked
(the amount used must not exceed the
“MAX” mark in the drawer).
Close the drawer gently.
C0065
8
7. At the end of the programme
4. Select the spin speed or option
or
The machine stops automatically.
If you have selected the RINSE HOLD option
, the
machine will stop with the water of the last rinse left in
the tub, to prevent the fabric from creasing. To drain
only, select position
or the drain programme “S”.
To drain and spin, select programme “M” or turn the
spin speed selector dial to the desired speed position: the
machine will spin at the selected speed.
The door is controlled by a safety device which releases
2 minutes after the end of the programme.
Switch the machine off by depressing the ON-OFF
button again. The mains-on light goes out.
When the programme has finished you are advised to
unplug the appliance and turn off the water taps.
450
Turn the dial to the required position.
550
1200
10
850
65
0
00
750
5. Select the programme
Turn the programme selector dial clockwise to the
programme K.
K
M0017a
6. Start the machine
Before starting up the machine check that:
● the appliance is plugged in
● the water supply taps are turned on
● the drain hose is correctly and securely positioned
● the door and the detergent dispenser drawer are
closed.
Depress the ON-OFF button: the mains-on light will
illuminate and the machine starts operating.
ON-OFF
T0001S
9
4. Start the machine
DRYING 2.5 KG OF COTTON
You have for example just machine-washed and spun at
1000 rpm 5 kg of laundry.
They are cotton fabrics of medium weight which you
want to iron as soon as they are dry.
Switch off the machine.
Then remove the laundry from the appliance and divide
the items to obtain two loads of approx. 2.5 kg each.
Depress the ON-OFF button, the mains-on light and
drying light will illuminate and the machine starts
operating.
ON-OFF
1. Load the laundry
Open the door by pulling the handle outward.
Load the items one at a time and close the door.
T0001S
2. Select the programme
5. At the end of the programme
Turn the programme selector dial clockwise to
programme J.
The machine stops automatically and the drying light
goes out.
The door is controlled by a safety device which releases
2 minutes after the end of the programme.
Switch the machine off by depressing the ON-OFF
button again, the mains-on light goes out.
If the laundry is still too damp, select a further brief
drying time, bearing in mind that during the last 10
minutes the appliance carries out a cooling and
anticrease phase.
When the programme has finished you are advised to
unplug the appliance and turn off the water taps.
J
M0017b
3. Select the required time
Following indications given in the programme chart on
page 17, turn the time selector dial clockwise to the 60
mins setting (light blue section).
60
M0019a
10
6. At the end of the programme
AUTODRYING 1 KG OF MIXED FABRICS
You intend to wash and dry automatically 1 kg of mixed
fabrics which do not need ironing.
Proceed as follows:
1. Load the laundry.
2. Add the washing powder and fabric softener.
The machine stops automatically and the drying light
goes out.
The door is controlled by a safety device which releases
2 minutes after the end of the programme.
Switch the machine off by depressing the ON-OFF
button again, the mains-on light goes out.
If the laundry is still too damp, select a further brief
drying time, bearing in mind that during the last 10
minutes the appliance carries out a cooling and
anticrease phase.
When the programme has finished you are advised to
unplug the appliance and turn off the water taps.
3. Select the programme
Turn the programme selector dial clockwise to
programme K.
K
M0017a
4. Select the required time
Following indications given in the programme chart on
page 17, turn the time selector dial clockwise to the 60
mins setting (green section).
60
M0019a
5. Start the machine
Depress the ON-OFF button: the mains-on light comes
on and the machine starts operating.
ON-OFF
T0001S
Note:
The drying light stays out until the laundry has spun. It
illuminates when the drying cycle starts.
11
Washing and Drying Hints
Do NOT overload the machine. Weigh the laundry the
first few times you use the appliance.
●
The average weights of the most common items are
listed below as a guide:
1000g = 1 kg
Sheet
Pillow case
100-200 g
Tablecloth
400-500 g
Serviette
50-100 g
Tea towel
70-120 g
Linen hand towel
100-150 g
Towelling hand towel
150-250 g
Towelling bath towel
700-1000 g
Bath robe
●
700-1000 g
●
●
●
1000-1500 g
Man’s shirt
200-300 g
Apron
150-200 g
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
Load the laundry loosely alternating large items with
small ones.
Sort the laundry according to the type of fabric,
colour-fastness and how dirty it is.
Avoid washing unhemmed or torn items as they may
unravel.
Before washing, empty all pockets of small objects
which may have been left inside (coins, keys, screws
etc). as these could damage the drain pump.
When washing curtains, remove the hooks.
Close poppers and zips and fasten loose buttons.
It is essential to wash new coloured items separately
when washing for the first time.
When washing fabrics requiring different wash
temperatures together, always select the lowest
temperature.
White items should not be washed with coloured
items.
Very small items (handkerchiefs, ribbons, socks etc)
should be washed in a washing bag or a pillow case.
Use a good quality detergent suitable for automatic
washing machines.
Use the correct quantities of detergent.
For wool, use gentle detergent only in small
quantities.
Bleach is very corrosive; it should be used with care
and kept out of reach of children.
●
●
●
●
Some stains such as fruit, wine, grass, rust etc. are
difficult to remove and should be treated before
washing with specific products, which can be found
in most household shops. In some cases it may help
to soak the stain before washing with a special presoak product or biological detergent.
If you have used the machine to wash, rinse or spin
only non-colour fast garments, there may be dye left
in the sump. To ensure any subsequent wash is not
contaminated with the dye, select and carry out a
rinse and spin programme, without any garments, to
ensure that any dye is removed from the sump.
Do not leave the damp laundry load in a heap too
long before drying.
Avoid drying dark clothes with light coloured fluffy
items such as towels as these can attract the fluff.
If you overdry the laundry, besides wasting energy,
any subsequent ironing may become more difficult
because the fabric could be heavily crumpled.
Remove the laundry when the appliance has finished
drying.
To avoid a static charge when drying is completed,
use either a fabric softener when you are washing the
laundry or a fabric conditioner specifically for
tumble dryers.
Particularly delicate items such as synthetic curtains,
woollen and silk, garments with metal inserts, nylon
stockings, bulky garments such as anoraks,
bedcovers, quilts, sleeping bags and duvets must not
be machine dried.
Garments padded with foam-rubber or materials
similar to foam-rubber must not be machine dried;
they represent a fire hazard.
Also, fabrics containing residues of setting lotions or
hair sprays, nail solvents or similar solutions must
not be machine dried in order to avoid the formation
of harmful vapours.
For drying, follow the indications given on the
manufacturer’s labels.
Drying at high temperature
Drying at reduced temperature
Do not tumble dry
Important:
As a dryer, the machine works on the condensation
principle.
Therefore, the water taps must be open and the
drain hose must drain water into a sink or into
the drain pipe, even during the drying cycle.
12
Which detergent?....
And in which form?
To ensure you obtain the best wash results from your
appliance, it is important to use the right detergent in
your everyday wash, and only detergents recommended
for use in automatic machines.
To maintain the appearance of your clothes and
household textiles and to make them last longer you
should use different types of detergent for different
washes, whether for whites, colours or delicates.
Not only are there different types of detergent, but they
are also available in different forms. Whether you chose
a powder or liquid in traditional or compact form is
your own personal choice.
TRADITIONAL POWDERS
Pour the powder directly into the dispenser drawer. Do
not sprinkle powder onto clothes in the machine drum.
TRADITIONAL LIQUIDS
WHITES
Liquid can be placed in the main wash compartment of
the detergent drawer marked with the symbol
, start
the machine immediately upon placing the
detergent in the dispenser drawer.
Alternatively the detergent is measured into the
specially designed dosing device* which should be
placed on top of the laundry, and at the back of the
machine drum.
We recommend the Ariel product
range which is biological and
designed to provide excellent
cleaning and stain removal even
at low temperatures.
NON BIOLOGICAL
If you prefer to use a non
biological detergent, which does
not contain enzymes we
recommend Fairy. Fairy provides
good cleaning and stain removal.
COMPACT POWDERS AND LIQUIDS
Compact detergents (or concentrates as they are also
known) are available in liquid or powder form, and
generally require a smaller dosage. Follow the
manufacturer’s instructions to ensure the most
economical usage. Pour the detergent directly into the
dispenser drawer, or alternatively measure the detergent
into the specially designed dosing device* which
should be placed on top of the laundry, and at the back
of the machine drum.
COLOUREDS
For coloured items you should use a
detergent which is designed to clean
while maintaining the original colour.
Ariel Color does not contain bleach
and therefore helps to preserve
colours.
* If you use a dosing device in a washer dryer,
please ensure the dosing device/ball is removed
before carrying out a drying programme.
DELICATE ITEMS
FABRIC CONDITIONERS
When washing delicates such as
woollens, you should use a product
which is specially designed to care for
fine fabrics.
Dreft Automatic is suitable for
woollens and other delicates.
These are ideal for improving ‘softness’, and also
reduce static cling on synthetics and make ironing
easier. They are available in two types:
For example Lenor liquid fabric
softener, for use in the washing
machine/washer dryer. The
liquid fabric softener should be
poured into the compartment
marked with the symbol .
Follow the manufacturer’s dosage
instructions and never exceed the
MAX level.
LAUNDRY BLEACH
For additional stain removal you may
wish to use a product such as Ace
Gentle Bleach which is used in addition
to your chosen detergent. Ace is
suitable for all washable fabrics
including silks, woollens and coloureds.
Bounce conditioning sheets for use
in a tumble dryer. We recommend
the conditioning sheets are pinned
(using a safety pin) to an article
of laundry and placed in the
tumble dryer.
13
Wash Care Symbols
Wash care labels inside garments recommend how to launder your clothes with the best results. The care labelling
code is in line with care labelling used in the rest of Europe. The symbols used make it easy to select the correct
programme on your washing machine.
WASHING SYMBOL
WASH ACTION
95
Normal (Maximum)
White Cotton or Linen
without Special Finishes
60
Normal (Maximum)
Cotton, Linen or Viscose
without Special Finishes
Colourfast at 60°C.
50
Reduced (Medium)
Nylon, Polyester/Cotton, Viscose
with Special Finishes,
Cotton/Acrylic Mix.
40
Normal (Maximum)
Cotton, Linen or Viscose
Colourfast at 40°C but not 60°C.
40
Reduced (Medium)
Acrylics, Acetate, Triacetate, Wool
mixes, Polyester/wool blends.
40
Much Reduced (Minimum)
Hand wash only
FABRIC
Wool, wool mixtures, Silks
Do not machine wash
BLEACHING
Chlorine bleach may be used
IRONING
Hot iron
Cotton, Linen, Viscose
Warm iron
Polyester mixtures, Wool
Cool iron
Acrylic, Nylon, Polyester
DRY CLEANING
May be dry cleaned. Other letters and/or a bar beneath the circle will
indicate the required process to the dry cleaner.
TUMBLE DRYING
with high heat setting
with low heat setting
May be tumble dried
X
A cross through any symbol means «DO NOT»
Important Notes
fabric conditioner to avoid the conditioner entering the
machine prematurely.
When using liquid detergent and a prewash programme,
place the detergent into the correct compartment in the
dispenser drawer, after the prewash has finished.
For best results, always use the dispenser drawer for
dispensing detergents and liquid additives.
Once the dispenser has been filled, close it by pushing it
in gently. This is particularly important if you are using
14
Washing Programmes
Programmes for cotton and linen
Wash programme/
Washing symbol
Degree of soil
and type of laundry
WHITES
+
PREWASH
For heavy soiled cotton
items.
WHITES
White cotton, for
example normally soiled
work garments, sheets,
household linen,
underwear, towels.
Fast coloured cotton or
FAST
COLOUREDS linen fabrics, shirts,
underwear, towels.
Non fast coloured
NON- FAST cotton or linen fabrics,
COLOUREDS shirts, blouses,
underwear.
Programme
dial position
Possible
options
Max.
load
A
Prewash at 40 °C
Wash at 95°C
3 rinses
Long spin
HALF LOAD
VARIABLE SPIN
RINSE HOLD
NO SPIN
5 kg
B
Wash at 95 °C
3 rinses
Long spin
HALF LOAD
VARIABLE SPIN
RINSE HOLD
NO SPIN
5 kg
C(*)
Wash at 60 °C
3 rinses
Long spin
HALF LOAD
VARIABLE SPIN
RINSE HOLD
NO SPIN
5 kg
D
Wash at 40 °C
3 rinses
Long spin
HALF LOAD
VARIABLE SPIN
RINSE HOLD
NO SPIN
5 kg
Description
RINSES
Separate rinse cycle for
hand washed cotton
and linen items
F
4 rinses
Long spin
VARIABLE SPIN
RINSE HOLD
NO SPIN
5 kg
FRESHEN UP
For softening hand
washed items
G
1 rinse
Long spin
VARIABLE SPIN
RINSE HOLD
NO SPIN
5 kg
SPIN
Separate spin for
cotton and linen items
H
Long spin
VARIABLE SPIN
5 kg
(*) This programme at 60°C with cold water filling is the reference programme for the Energy label according to
EEC Directive 92/75.
Water filling: 30°-30°-40° programmes: cold water filling
30°-50°-60° programmes: hot and cold filling
30°-50°-95° programmes: hot water filling
Important!
● Some programmes when selected may start with a short drain. This is quite normal and not a fault with the appliance.
When a programme is selected, the selector dial will advance to the water filling position. E.g. Programme B is
selected, there is a short drain. The appliance takes in water and the selector will appear to move to the C position.
The appliance will have memorised the programme selected, in this case B, and will run the correct programme
even though the selector dial appears to be at position C.
● We recommend that you do not switch the appliance off and on during its operation. This would modify the
memorised programme in progress with unsatisfactory washing results.
15
Washing Programmes
Programmes for synthetics, mixed fabrics, delicates and wool
Wash programme/
Washing symbol
Degree of soil
and type of laundry
Programme
dial position
Possible
options
Max.
load
K
Wash at 50 °C
3 rinses
Short spin
VARIABLE SPIN
RINSE HOLD
NO SPIN
2.5 kg
VARIABLE SPIN
RINSE HOLD
NO SPIN
2.5 kg
VARIABLE SPIN
2.5 kg
Description
MIXED
FABRICS
Synthetic or mixed
fabrics, underwear,
coloured garments,
non-shrink shirts,
blouses.
WORN
ONCE
Lightly soiled synthetic
or mixed fabrics
L
Wash at 30 °C
3 rinses
Short spin
SHORT
SPIN
Separate spin for
delicate items
M
Draining of water
and short spin
Specially tested
programme for wool
garments bearing the
“Pure new wool, nonshrink, machine
washable” label.
P
Wash at 40 °C
3 rinses
Short spin
VARIABLE SPIN
RINSE HOLD
NO SPIN
1 kg
DELICATES
Delicate fabrics, for
example curtains
Q
Wash at 40 °C
3 rinses
Short spin
VARIABLE SPIN
RINSE HOLD
NO SPIN
2.5 kg
RINSES
This programme can be
used for rinsing hand
washed garments.
R
3 rinses, with fabric
softener, if required
Short spin
VARIABLE SPIN
RINSE HOLD
NO SPIN
2.5 kg
DRAIN
For emptying out the
last rinse water in
programmes with the
Rinse Hold option
.
S
Draining of water
WOOL
-
Important!
● Some programmes when selected may start with a short drain. This is quite normal and not a fault with the
appliance.
When a programme is selected, the selector dial will advance to the water filling position.
●
We recommend that you do not switch the appliance off and on during its operation. This would modify the
memorised programme in progress with unsatisfactory washing results.
●
The wool wash cycle of this machine has been approved by Woolmark for the washing of machine washable
Woolmark products provided that the garments are washed according to the instructions on the garment label and
those issued by the manufacturer of this washing machine. M9604.
16
Drying Programmes
Degree of drying
Type of fabric
Cotton and linen
(towels, T-shirts,
bathrobes)
Store dry (*)
Programme J
Suitable for items
to put away
Synthetic and mixed
without ironing
fabrics (jumpers,
blouses, underwear,
household linen)
Programme N
Iron dry
Suitable for
ironing
Max. load
Spin speed
Drying time mins
1000
Light blue section
80-90
1200
70-80
1000
50-60
1200
40-50
1.5,0 kg
850
Green section
90-100
1,0 kg
850
60-70
1000
Light blue section
60-70
1200
50-60
1000
40-50
1200
30-40
2.5 kg
1.0 kg
Cotton and linen
(sheets, tablecloths,
shirts, etc.)
2.5 kg
Programme J
1.0 kg
(*) The STORE DRY drying programme for cotton is the reference programme for the Energy Label data, in
compliance with EC directive 92/75.
17
Maintenance and Cleaning
Before any maintenance or cleaning is carried out you
must DISCONNECT the appliance from the electricity
supply.
Descaling
The water we use normally contains lime. It is a good
idea to periodically use a water softening powder in the
machine. Do this separately from any laundry washing,
and according to the softening powder manufacturer's
instructions. This will help to prevent the formation of
lime deposits.
C0066
C0067
C0068
P1086
After each wash
Leave the door open for a while. This helps to prevent
mould and stagnant smells forming inside the appliance.
Keeping the door open after a wash will also help to
preserve the door seal.
Cleaning the drawer recess
Maintenance Wash
Having removed the drawer, use a small brush to clean
the recess, ensuring that all washing powder residue is
removed from the upper and lower part of the recess.
Replace the drawer and run the rinse programme
without any clothes in the drum.
With the use of low temperature washes it is possible to
get a build up of residues inside the drum.
We recommend that a maintenance wash be performed
on a regular basis.
To run a maintenance wash:
● The drum should be empty of laundry.
● Select the hottest cotton wash programme.
● Use a normal measure of detergent, must be a
powder (such as Ariel Futur).
External cleaning
P0038
Clean the exterior cabinet of the appliance with soap
and water only, and then dry thoroughly.
Cleaning the filter
Cleaning the dispenser drawer
A clean filter is important for the correct operating of
the machine, and should therefore be cleaned after every
washing programme.
Open the filter door and place a container underneath to
catch any spillage.
The water drain filter
The washing powder and additive dispenser drawer
should be cleaned regularly.
Remove the drawer by pressing the catch downwards
and by pulling it out. Flush it out under a tap, to remove
any traces of accumulated powder.
To aid cleaning, the top part of the additive
compartment should be removed.
P0011
18
If the filter is blocked and the machine is unable to drain
you will need to drain the water manually from the
machine at this stage. To do this, unhook the drain hose
from the standpipe or sink and hold the end of the hose
over a bowl on the floor. The water should drain by
gravity into the bowl. When the bowl is full, hook the
hose back up and empty the bowl. Repeat the procedure
until water stops flowing out.
Unscrew and remove the filter.
Clean the filters using a hard bristle brush.
Tighten up the inlet hoses.
P1090
The dangers of freezing
If the machine is exposed to temperatures below 0°C,
certain precautions should be taken.
● Turn off the water taps.
● Unscrew the inlet hoses.
● Unhook the drain hose from the rear support and
position the end of this hose and that of the inlet
hoses in a bowl. Run the draining programme.
● Disconnect the appliance.
● Screw the inlet hoses and reposition the drain hose.
● When you intend to start the machine again, make
sure that the room temperature is above 0°C.
P0133
P0132
Clean carefully under a fast running tap.
P0040
Warning
When the appliance is in use and depending on the
programme selected there can be hot water in the filter.
Never remove the filter during a wash cycle, always
wait until the appliance has finished the cycle, and is
empty. When replacing the filter, ensure it is securely
retightened so as to stop leaks and young children being
able to remove it.
The water inlet filters
If your water is very hard or contains traces of lime
deposit, the water inlet filters may become clogged.
It is therefore a good idea to clean them from time to
time.
Turn off the water taps. Unscrew the water inlet hoses.
19
Something Not Working
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out
an engineer. Before contacting your local Service Force Centre, please carry out the checks listed below.
IMPORTANT: if you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation, a charge will be made even if the appliance is under guarantee.
Symptom
Possible causes
The machine does not start
●
●
●
●
●
●
The machine does not fill
●
●
●
●
The machine fills then empties
immediately
●
●
●
The machine does not empty and/or
does not spin
●
●
●
●
●
●
There is water on the floor
●
●
●
●
●
Unsatisfactory washing results
●
●
●
●
The machine vibrates when spinning
●
●
●
●
●
The door has not been closed.
The plug is not properly inserted in the power socket.
There is no supply at the socket
The main fuse or the fuse in the plug has blown.
The selector dial is not correctly positioned.
The ON-OFF button has not been depressed.
Ensure the water taps are open.
The filters in the inlet hoses are blocked.
The inlet hoses may be squashed or kinked.
The door has not been closed.
The end of the drain hose is too low.
The end of the drain hose is submerged in water.
There is no vent in the end of the drain hose.
The drain hose may be squashed or kinked.
The RINSE HOLD
or NO SPIN
option has been selected.
The drain filter may be blocked.
The drain hose extension, if fitted, is not correct. Follow the
instructions for connecting to the waste.
The drainage system pipes are blocked.
The wash load is unbalanced: redistribute the clothes inside the drum to
allow the machine to spin.
Too much detergent or unsuitable detergent has been used (creates too
much foam).
Check whether there are any leaks from one of the inlet hose(s) fittings.
It is not always easy to see this as the water runs down the hose; check
to see if it is damp.
The drain hose may be damaged or not securely positioned.
The detergent dispenser drawer or recess is clogged.
The drainage system pipes are blocked.
Too little detergent or unsuitable detergent has been used. An
insufficient amount of detergent leaves the laundry looking grey and
causes lime scale to form.
Stubborn stains have not been treated prior to washing
The correct wash programme has not been selected.
Too much laundry has been placed in the drum.
The internal packing has not been removed.
The machine is in contact with the wall or furniture.
The machine is not stable and level (check diagonally).
The washing load is badly distributed in the drum.
Maybe there is very little laundry in the drum.
20
Symptom
Possible causes
The door will not open
●
●
●
The programme is still running.
The door lock has not yet released.
Water in the tub: the door cannot be opened if water is present in the
tub.
Spinning starts late or the machine
does not spin
●
The electronic unbalance detection device has cut in because the
laundry is not evenly distributed in the drum. The laundry is
redistributed by reverse rotation of the drum. This may happen several
times before the unbalance disappears and normal spinning can resume.
If, after 20 minutes, the laundry is still not evenly distributed in the
drum, the machine will not spin. In this case, redistribute the load
manually and reselect the spin programme.
The machine makes an unusual
noise
●
The machine is fitted with a type of motor which makes an unusual
noise compared with other traditional motors. This new motor ensures
a softer start and more even distribution of the laundry in the drum
when spinning, as well as increased stability of the machine.
No water is visible in the drum
●
Machines based on modern technology operate very economically
using very little water without affecting performance.
The machine does not dry or does
not dry properly
●
The drying time has not been selected
The water taps are not turned on
The drain filter is clogged
The machine is overloaded
The selected drying time/section is not suitable for the laundry or a
lower spin speed has been selected.
●
●
●
●
Service & Spare Parts
In the event of your appliance requiring service, or if
you wish to purchase spare parts, please contact your
local Service Force Centre by telephoning:
Republic of Ireland
Tel: +353 (0) 1 353 4090751
Email:service.eid@electrolux.ie
Mod. ..........
Prod. No. ...........
Ser. No. .........
0870 5 929929
Your telephone call will be automatically routed to the
Service Force Centre covering your post code area.
For the address of your local Service Force Centre and
further information about Service Force, please visit the
website at www.serviceforce.co.uk.
Before calling out an engineer, please ensure you have
read the details under the heading “Something Not
Working”.
When you contact the Service Force Centre you will
need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of fault
4. The model and serial number of the appliance (found
on the rating plate - see picture)
5. The purchase date.
Please note that a valid purchase receipt or guarantee
documentation is required for in-guarantee service calls.
For Customer Care in the Republic of Ireland please
contact us at the following address:
Zanussi-Electrolux
Electrolux Group (Ire) Ltd
Long Mile Road
Dublin 12
21
Mod. ..........
Prod. No. ...........
P0042
Ser. No. .........
Customer Care
For general enquiries concerning your Zanussi
Electrolux appliance or for further information on
Zanussi Electrolux products, please contact our
Customer Care Department by letter or telephone at the
address below or visit our website at www.zanussi.co.uk
Customer Care Department
Zanussi Electrolux
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel 08705 727727*
* calls to this number may be recorded for training
purposes.
Guarantee Conditions
Standard guarantee conditions
Exclusions
We, Zanussi Electrolux undertake that if, within 12
months of the date of the purchase, this Zanussi
Electrolux appliance or any part thereof is proved to be
defective by reason only of faulty workmanship or
materials, we will, at our option, repair or replace the
same FREE OF ANY CHARGE for labour, materials or
carriage on condition that:
● The appliance has been correctly installed and used
only on the electricity supply stated on the rating
plate.
● The appliance has been used for normal domestic
purposes only, and in accordance with the
manufacturer’s instructions.
● The appliance has not been serviced, maintained,
repaired, taken apart or tampered with, by any
person not authorised by us.
All service work under this guarantee must be
undertaken by a Service Force Centre.
Any appliance or defective part replaced shall become
the Company’s property.
This guarantee is in addition to your statutory and other
legal rights.
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
This guarantee does not cover:
●
●
●
●
Damage or calls resulting from transportation,
improper use or neglect, the replacement of any light
bulbs or removable parts of glass or plastic.
Costs incurred for calls to put right an appliance
which is improperly installed or calls to appliances
outside the United Kingdom.
Appliances found to be in use within a commercial
environment, plus those which are subject to rental
agreements.
Products of Zanussi Electrolux manufacture which
are NOT marketed by Zanussi Electrolux.
European guarantee
If you should move to another country within Europe
then your guarantee moves with you to your new home
subject to the following qualifications:
● The guarantee starts from the date you first
purchased your product.
● The guarantee is for the same period and to the same
extent for labour and parts as exists in the new
country of use for this brand or range of products.
● The guarantee relates to you and cannot be
transferred to another user.
● Your new home is within the European Community
(EC) or European Free Trade Area.
● The product is installed and used in accordance with
our instructions and is only used domestically, i.e. a
normal household.
● The product is installed taking into account
regulations in your new country.
Before you move please contact your nearest Customer
Care Centre, listed below, to give them details of your
new home. They will then ensure that the local Service
Organisation is aware of your move and able to look
after you and your appliances.
France
Senlis
+33 (0)344 62 29 29
Germany
Nurnberg
+49 (0)800 234 7378
Italy
Pordenone
+39 (0)434 39 4700
Sweden
Stockholm
+46 (0)8 672 53 90
UK
Slough
+44 (0)1753 219897
Ireland
Dublin
+353 (0)1 4090751
22
Installation Instructions
It is dangerous to alter the specifications or
attempt to modify this product in any way.
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
Any plumbing work required to install this
appliance should be carried out by a qualified
plumber or competent person.
Should the appliance power supply cable need to
be replaced, this should be carried out by our
Service Force Centre.
Technical Specifications
DIMENSIONS
Height
Width
Depth
POWER SUPPLY VOLTAGE
TOTAL POWER ABSORBED
WATER PRESSURE
LOAD CAPACITY
85 cm
60 cm
58 cm
230-240 V/50 Hz
2050 W (10A)
Minimum
Maximum
50 kPa (0.5 bar)
800 kPa (8.0 bar)
Washing
Cotton, linen
Synthetics
Delicate fabrics
Wool
Drying
Cotton, linen
Synthetics
5.0 kg
2.5 kg
2.5 kg
1.0 kg
2.50 kg
1.52 kg
SPIN SPEED
Maximum
1200 rpm
CONSUMPTION DATA FOR WASHING
5 KG NORMALLY SOILED COTTON
ITEMS AT 60°C WITH COLD WATER
FILLING
Energy
Water
1.10 kWh
63 litres
145 mins
This appliance complies with the following E.E.C. Directives:
- 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications;
- 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.
23
Unpacking
Fill all the holes with the plastic plugs supplied with the
instruction booklet.
All transit bolts and packing must be removed
before using the appliance.
You are advised to keep all the packaging for re-use in
case the machine is to be transported again.
Using a spanner unscrew and remove the two rear
bottom screws. Slide out the two plastic pins.
Lay the machine gently on its back, making sure that the
hoses are not squashed.
P1128
P0002
Important !
You are advised to keep all the packaging for re-use in
case the machine is to be transported again.
In case of moving out the same precautions as per
paragraphe “The dangers of freezing” must be taken
i.e. the residual water in the hoses must be pumped out.
Positioning
P0001
P1129
Install the machine on a flat hard floor.
Make sure that air circulation around the machine is not
impeded by carpets, rugs etc. Check that the machine
does not touch the wall or other kitchen units.
Never place cardboard, wood or similar materials under
the machine to compensate for any unevenness in the
floor.
Your new washing machine has been designed to be
permanently plumbed in to your home’s water supply
and drainage system. However, if this is not possible, it
may be connected to suitable existing taps with the
drain hose discharging into a sink.
The appliance has two inlet hoses, hot and cold, with
female 3/4” BSP thread connectors. If this connection is
not compatible with the plumbing of the existing
installation, a variety of connectors are available from
good hardware stores and plumbers merchants to suit
most domestic plumbing. Any alteration to your
existing plumbing must be carried out by a competent
person, or qualified plumber.
Remove the polystyrene block from the bottom of the
machine and release the two plastic bags.
Very carefully slide out the left polythene bag, removing
it towards the right and then downwards.
1
2
3
P1124
P1126
Repeat the operation for the right polythene bag,
removing it towards the left and then upwards.
Installation on a Suspended Floor
P1127
Suspended wooden floors are particularly susceptible to
vibration. To help prevent vibration we recommend you
place a waterproof wood panel, at least 15 mm thick
under the appliance, secured to at least 2 floor beams
with screws. If possible install the appliance in one of
the corners of the room, where the floor is more stable.
Remove the polystyrene base.
Set the machine upright and unscrew the remaining rear
screw. Slide out the relevant pin.
24
Water inlet
Water drainage
The inlets on the back of the appliance are colour coded,
blue for cold and red for hot.
Connect the hose supplied with the machine to a tap
with a 3/4” thread.
Do not use previously used hoses.
This appliance is designed to be permanently plumbed
into your home's drainage system using one of the
following methods.
1. Into a drainage standpipe.
Firstly form a hook in the end of the drain hose using
the “U” piece” supplied.
“U” piece
supplied
P1088
P1199
If only a cold water supply is available, connect the two
hoses to a cold water outlet by means of a «Y»
connection piece.
Installation should comply with local water authority
and building regulations’ requirements.
The appliance must be given a separate cold water
supply and not be connected to a mixer tap, a single
outlet water heater or a booster pump. A minimum
water pressure of 50 kPa (0.48) bar is required for safe
operation of the appliance.
Place the drain hose into your standpipe, which should
have an internal diameter of approximately 38mm thus
ensuring there is an air break between the drain hose
and standpipe.
30 cm (12")
38 mm (11.2”)
standpipe
diameter
If you cannot make the cold water connection direct
from the rising mains, you may be able to operate the
appliance from your cold water storage system.
There should be a minimum distance of 5.02m
(16.5 ft) between the appliance’s inlet and the bottom of
the water storage tank.
There will be sufficient pressure for the hot water
supply, providing there is a minimun height of 2.74
metres (9 ft) between the bottom of the cold water
storage tank and the bottom of the hot water cylinder.
Set the hoses correctly by loosening the ring nuts. After
positioning the inlet hoses, be sure to tighten the ring
nuts again to prevent leaks.
P1074
When discharging into a standpipe ensure that the top of
the standpipe is no more than 90cm (35.4'') and no less
than 60cm (23.6'') above floor level.
Max. 90 cm (35.4”)
Min. 60 cm (23.6”)
3 pin
P1039
The drain hose may be extended to a maximum of 4
metres. An additional drain hose and joining piece is
available from your local Service Force Centre.
The joining piece must have an internal diameter of
18mm.
P0021
25
2. Onto a sink outlet spigot.
Some vibration is inevitable, especially if mounted on a
wooden floor. Sprung wooden floors are particularly
susceptible to vibration. For advice, consult a builder. If
possible, always place the machine on a solid floor.
If the outlet spigot has not been used before, remove
any blanking plug that may be in place.
Special conditions
If the floor is carpeted or covered with crumbly or soft
material, insert a rigid support base under the feet to
prevent noise, vibration or displacement. The base
should protrude a few centimetres beyond the edges of
the machine.
P1197
Warning
The machine should NOT be placed on deep pile
carpeting.
Push the drain hose onto the spigot and secure with a
clip if required, ensure a loop is formed in the drain
hose (see diagram) to prevent waste from the sink
entering the washing machine.
Note
Please ensure that when the appliance is installed it is easily
accessible for the engineer in the event of a breakdown.
In the interest of the environment
Loop
Washing machines and dishwashers should be connected
to the FOUL drainage system, the water will then be
taken to a sewage works for treatment before being
discharged safely into a river.
It is essential that these appliances are not connected to
the surface water drainage system as this water is
discharged directly into a river or stream and may cause
pollution.
If you require any further advice please contact your local
water authority.
P1198
The drain hose may be extended to a maximum of 4
metres. An additional drain hose and joining piece is
available from your local Service Force Centre.
The joining piece must have an internal diameter of 18mm.
Important
Before connecting up the machine to new pipework or
to pipework that has not been used for some time, run
off a reasonable amount of water to flush out any debris
that may have collected in the pipes.
Levelling
Level the washing machine by raising or lowering the
feet. The feet may be tight to adjust as they incorporate
a self locking nut, but the machine MUST be level and
stable.
SHOWER
SINK
TOILET
BATH
WASHING
MACHINE
BIDET
DISHWASHER
RAINWATER
'RUN-OFF'
FOUL DRAIN
SURFACE WATER
DRAINS & SEWERS
P1051
UNTREATED
DISCHARGE
FOUL SEWERS
SEWAGE
TREATMENT
WORKS
TREATED
DISCHARGE
Any necessary adjustment can be made with a spanner.
Accurate levelling prevents vibration, noise and
displacement of the machine during operation.
RIVER
P0987
26
RIVER
Electrical connection
The wire coloured green and yellow must be connected
to the terminal marked with the letter «E» or by the
earth symbol
or coloured green and yellow.
The wire coloured blue must be connected to the
terminal marked «N» or coloured black.
The wire coloured brown must be connected to the
terminal marked «L» or coloured red.
Upon completion there must be no cut, or stray strands
of wire present and the cord clamp must be secure over
the outer sheath.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
The manufacturer declines any liability should
this safety measure not be observed.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the appliance’s
rating plate. The rating plate is located at the top of the
rim of the open door.
WARNING:
A cut off plug inserted into a 13 amp socket is
a serious safety (shock) hazard.
Ensure that the cut off plug is disposed of
safely.
Mod. ..........
Prod. No. ...........
Ser. No. .........
Should the appliance power supply cable neeed to be
replaced, this should be carried out by our Service
Force Centre.
Mod. ..........
Prod. No. ...........
Note
When the appliance is installed the power supply cable
must be accessible.
Ser. No. .........
P0042
The appliance is supplied with a 13amp plug fitted.
In the event of having to change the fuse in the plug
supplied, a 13amp ASTA approved (BS1363A) fuse
must be used.
Should the plug need to be replaced for any reason,
proceed as described below.
The wires in the mains lead are coloured in accordance
with the following code:
Green and Yellow
- Earth
Blue
- Neutral
Brown
- Live
Permanent connection
In the case of permanent connection it is necessary that
you install a double pole switch between the appliance
and the electricity supply (mains), with a minimum gap
of 3mm between the switch contacts and of a type
suitable for the required load in compliance with the
current electrical regulations.
The switch must not break the yellow and green earth
cable at any point.
GREEN & YELLOW
13A
E
N
L
BROWN
BLUE
P1041
CORD CLAMP
27
From the Electrolux Group. The world’s No. 1 choice.
The Electrolux Group is the world's largest producer of powered appliances for kitchen, cleaning and outdoor use.
More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum
cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150
countries around the world.
© Electrolux plc 2004
Download PDF

advertising