User manual | LevelOne

LevelOne
FSW-1640TX
FSW-2440TX
16/24-Port 10/100Mbps 11" Fast Ethernet Smart Switch
User’s Guide
Version: 1.0
2
TABLE OF CONTENTS
1
UNPACKING INFORMATION ........................................................................5
2
PRODUCT INTRODUCTION ..........................................................................6
2.1
MODELS .........................................................................................................6
2.2
KEY FEATURES ..............................................................................................6
2.3
FRONT PANEL ................................................................................................6
2.3.1
10/100Mbps TP Ports............................................................................6
2.3.2
Cabling..................................................................................................6
2.3.3
Status LEDs...........................................................................................6
2.4
REAR PANEL ..................................................................................................7
2.4.1
Power Socket.........................................................................................7
3
INSTALLATION ................................................................................................8
3.1
3.2
4
HELPFUL SUGGESTIONS ..............................................................................9
4.1
4.2
4.3
4.4
4.5
5
PRIOR TO INSTALLATION ................................................................................9
HALF- AND FULL-DUPLEX .............................................................................9
FAST ETHERNET .............................................................................................9
AUTO-NEGOTIATION ......................................................................................9
MAC ADDRESS TABLE.................................................................................10
SMART FUNCTION SETTINGS ................................................................... 11
5.1
6
TO LOCATE THE SWITCH ON A DESKTOP ..........................................................8
RACKMOUNT PLACEMENT ..............................................................................8
START SMART FUNCTION .............................................................................11
USE FUNCTION MENU .................................................................................12
6.1
MAIN MENU .................................................................................................12
6.2
AGING TIME.................................................................................................13
6.3
PORT STATUS ...............................................................................................13
6.3.1
E: Port Enable/Disable .......................................................................15
6.3.2
A: Port AN Enable/Disable or Reset...................................................15
6.3.3
R: port rate control 10/100M ..............................................................16
6.3.4
D: Port duplex mode Half/Full ...........................................................16
6.3.5
F: Flow control enable/disable ...........................................................17
6.4
MIRROR FUNCTION ......................................................................................18
6.4.1
P: set Port mirror status......................................................................19
3
R: Reset all mirror Configure..............................................................22
6.4.2
6.4.3
I/E: Ingress/Egress rule Configure......................................................22
6.5
VLAN FUNCTION ........................................................................................23
6.6
QOS FUNCTION ...........................................................................................25
6.6.1
T: TCI THRESHOLD. .........................................................................25
6.6.2
W: Set High/Low queue weight. ..........................................................25
6.6.3
P: Port Based Qos...............................................................................26
6.7
TRUNKING FUNCTION ..................................................................................26
6.8
LOAD DEFAULT ............................................................................................30
6.9
SAVE ............................................................................................................30
7
SAMPLE APPLICATION................................................................................32
8
PRODUCT SPECIFICATIONS ......................................................................33
4
1
UNPACKING INFORMATION
Thank you for purchasing LevelOne 11" Fast Ethernet Switch. Before
continuing, please check the contents of the product package. This product
package should contain the following items:
One (1) Switch
One (1) Power Cord
One (1) Console Cable
Four (4) Rubber Feet
Rackmount Kit
This User’s Guide
If anything is missing, please contact your place of purchase.
16-Port 100BASE-TX Fast Ethernet Switch
24-Port 100BASE-TX Fast Ethernet Switch
Power Cord
Console Cable
Rackmount Kit
Rubber Feet
User’s Guide
5
2
PRODUCT INTRODUCTION
2.1 Models
These LevelOne 11" Fast Ethernet Switches are multi-speed, versatile
network devices combining both standard and "Big-Pipe" ports under the
same hood. The Switches are Twenty-Four (24) ports and Sixteen (16) ports
Fast Ethernet Switches.
2.2 Key Features
Store-and-Forward technology filtering/forwarding is used to eliminate bad
packets.
Back-Pressure Flow-Control support for Half-Duplex operation.
IEEE802.3x Flow-Control support for Full-Duplex operation.
LEDs on front panel for easy access and real time viewing of Switch status.
All TP ports support Auto-MDI/MDIX, and Auto-Negotiation function.
2.3 Front Panel
16-Port 100BASE-TX Fast Ethernet Switch
24-Port 100BASE-TX Fast Ethernet Switch
2.3.1 10/100Mbps TP Ports
Each 10/100Mbps TP port provides an Auto-Negotiation function that senses
for the attached device's maximum operating speed and automatically sets
the Switch to operate at that speed. Users only need to connect a network
device into any TP port. Auto-MDIX is also supported on all TP ports which
allows uplinking to another Switch free of cross-over or straight cable
selection hassle.
2.3.2 Cabling
10Mbps -When transmitting at 10Mbps Category 3, 4 or 5 TP cabling with
RJ-45 sockets can be used.
100Mbps -To transmit at 100Mbps requires Category 5 TP cabling.
Port Type
Cable Type
Connector
10BASE-T
Category 3, 4 or 5 TP
RJ-45
100BASE-TX
Cat.5 TP
RJ-45
Note: Category 5 TP cable is recommended whenever installing new cabling.
2.3.3 Status LEDs
The Switches come with a complete range of LEDs. The table below lists
each LEDs name, color and a brief description of its function.
6
Name
Color Function
Pwr
Green Lit: Power "On"
LINK/ACT Green Lit: When the port has a valid physical connection with
another device.
Blinks: When the port is sending or receiving data
(Activity).
FD/Half Green Lit: When the port is set to Full-Duplex mode.
OFF: When the port is in Half-Duplex mode.
Speed
Green Lit: When the port is operating at 100Mbps.
Off: When the port is operating at 10Mbps.
2.4 Rear Panel
16-Port 100BASE-TX Fast Ethernet Switch
24-Port 100BASE-TX Fast Ethernet Switch
2.4.1 Power Socket
The Power Socket is designed to be used with the power cord included in the
product package.
Attach the female end of the cord to the power connector on the back panel.
Attach the male end of the cord to a grounded power outlet.
7
3
INSTALLATION
The LevelOne 11" Fast Ethernet Smart Switch is "Plug-&-Play". It does not
require software configuration. Users can immediately use any of the features
of this product simply by attaching the cables and turning on the power.
3.1 To locate the switch on a desktop
Attach the Four (4) rubber feet included in the product package to the
bottom of the Switch, one in each corner.
Place the Switch on a clean, flat desk or tabletop close to a power outlet.
Plug in all network connections and the power cord.
3.2 Rackmount placement
Attach One (1) rackmounting bracket on each side of the Switch front panel
and secure each bracket with the provided screws.
Use the other provided screws to secure each Switch to the rack.
8
4
HELPFUL SUGGESTIONS
4.1 Prior to Installation
Before installing the Switch and connecting network devices, it is important to
plan the network's layout. Things you should consider include:
Dedicated Bandwidth: File servers and other high-traffic hardware improve
their performance if they have their own dedicated 10Mbps or 100Mbps
bandwidth.
Full-Duplex: Determine which devices support Full-Duplex connections.
Fast Ethernet: Make sure rules for cable lengths and categories are
followed.
Auto-Negotiation: Devices with different speeds may be easily swapped
when the other end of the cable is fixed to a port with Auto-Negotiation.
4.2 Half- and Full-Duplex
The Switch supports both Half- and Full-Duplex modes for 10BASE-T and
100BASE-TX.
In Half-Duplex mode: Data cannot be transmitted and received at the same
time. Attached devices must finish transmitting data before they can receive
data.
In Full-Duplex mode: Data can be transmitted and received at the same
time.
However:
Full-Duplex transmission is only possible between two devices with a
dedicated link (ex: Switch-Switch, Switch-PC)
Both devices must have Full-Duplex capability
Both devices must be set to Full-Duplex (ex: Auto-Negotiation –
Auto-Negotiation, Non-Auto-Negotiation to Non-Auto-Negotiation)
The 100BASE-TX/10BASE-T ports on the Switch detect and set the line's
operating mode by using their Auto-Negotiation function.
4.3 Fast Ethernet
100BASE-TX is called "Fast Ethernet". In Fast Ethernet data travels ten times
faster (100Mbps) than in traditional Ethernet (10Mbps).
Below is a list of the cable types and connectors supported by the Switch for
10BASE-T and 100BASE-TX networks.
Port Type
Cable Type
Connector
10BASE-T Category 3, 4 or 5 TP RJ-45
100BASE-TX Cat. 5 TP
RJ-45
Note: If your 10BASE-T network currently uses Category 5 TP cabling, you
can instantly upgrade the network to a 100BASE-TX network by changing
network devices.
4.4 Auto-Negotiation
Every 10/100Mbps dual speed port on the Switch has a Built-In
"Auto-Negotiation" function. This technology automatically sets the best
possible bandwidth as soon as a connection is established with another
network device. This capability is achieved via the Switch’s Auto-Negotiation
function that automatically detects the modes and speeds the second
9
(attached) device is capable of.
Evaluating Auto-Negotiation Capability:
If attached device is:
The Switch will automatically set its TP ports
to operate at:
100Mbps,no
100Mbps (100BASE-TX, Half-Duplex)
Auto-Negotiation
100Mbps,with
200Mbps (100BASE-TX, Full-Duplex)
Auto-Negotiation
10Mbps,no Auto-Negotiation 10Mbps (10BASE-T, Half-Duplex)
10Mbps,with
20Mbps (10BASE-T, Full-Duplex)
Auto-Negotiation
Note: If the attached device is set to a fixed mode (ex: Forced Full-Duplex) it
will not operate as an Auto-Negotiation device.
4.5 MAC Address Table
Every Ethernet data packet includes both source and destination addresses.
This Six (6)-bytes ID is called the MAC (Media Access Control) Address.
The Switch can automatically learn and store MAC addresses. However, the
MAC address table is volatile: it disappears when the Switch is powered “Off”
or reset.
Note: When the network needs reconfiguration, we recommend turning off
the power first. After all nodes have been moved, turn the Switch back "On" to
rebuild the internal MAC address table.
10
5
SMART FUNCTION SETTINGS
5.1 Start Smart Function
The Switch has a smart function that you can use to manage your local area
network (LAN ) more effectively. You also can use the default setting to make
the Switch operate as a dumb switch.
If you want to use smart function, install the Switch as below:
Use the “RS-232” connector to connect the Switch to a computer. Connect
one (1) cable end to the Switch, and connect the other end to the computer’s
“COM1” or “COM2” port.
Note: If your Windows program doesn’t have a hyper terminal, you have to
install it first.
Power “ON” the Switch
Execute the “HyperTerminal” program:
Start Menu Æ Application Program Æ Communication Æ Hyper Terminal
Setup the connection content of Hyper Terminal:
In connection tag, select which “COM” port is used to connect PC and
the Switch.
Then press the “SETUP” button, set “Bits per second” to 9600, “Data
bits” to 8, “Parity” to None, “Stop bits” to 1, “Flow control” to None.
After finishing the setting-up action in Hyper Terminal window, press any key
to continue. Now the computer can connect to Switch and use the user
interface menu to select control function.
Note: If you also have “Term95”, it could be easier to use the following
procedures:
(a). Execute the “Term95” program;
(b). Select the “Setting” / “Line” into the ”RS232 settings” menu;
(c). RS232 settings: set as the following and select “Ok”.
Item
Setting
Port
COM
Baud rate
9600
Data bits
8 bits
Parity
None
Stop bits
1
Flow control
NA
(d). Power “ON” the Switch.
11
6
USE FUNCTION MENU
6.1 Main menu
Now we use the 24 ports switch as an example for explanation; the functions
of 16 ports switch is the same as 24 ports switch.
The main menu function selections are listed below:
1. Aging Time
2. Port Status
3. Mirror Function
4. VLAN Function
5. QOS Function
6. Trunking Function
7. Load Default
8. Save
After you connect the Switch through the console port, the following screen
shows up on the monitor:
LevelOne FSW-2440TX
24-Port Smart Switch
====================
Main Menu
====================
1. Aging Time
2. Port Status
3. Mirror Function
4. VLAN Function
5. QOS Function
6. Trunking Function
7. Load Default
8. Save
[TAB]: Next Item
Version:A1.0
[BACKSPACE]: Back
[ENTER]: Enter Sub Menu
Control Keys are displayed on the bottom of each menu:
Key
Function
TAB
Next Item
BACKSPACE
Back
Enter
Enter Sub Menu / Next Page
ESC
Exit from Sub Menu
12
6.2 Aging Time
You can Enable or Disable the Aging Time setting. The Aging Time setting is
from 1 to 65535 seconds.
LevelOne FSW-2440TX
24-Port Smart Switch
====================
Current AGE_TIME : 00300
(unit : 1 second)
---> (E)nable/(D)isable Aging Time?
(ESC): Exit
---> Please select: E
---> Enter Aging Time (1 ~ 65535): 300
Set Age Time to 00300......OK!
Press 'SPACE BAR' to continue
6.3 Port Status
When you enter Port Status, the first menu you will see is as below:
LevelOne FSW-2440TX
24-Port Smart Switch
====================
Port
01
02
03
04
05
06
07
08
09
10
11
12
---------------------------------------------------------------------------LINK
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
En
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
An
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
---
---
---
---
---
---
---
---
---
---
---
Duplex -----
---
---
---
---
---
---
---
---
---
---
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
Mirror OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Rate
---
Flow
ON
[E]:Rx/Tx Enable/Disable [A]:Auto-Negotiation [R]:Data Rate [D]:Duplex
Mode
[F]:Flow Control
[ESC]:Exit
[Enter]: Next Page
13
You can press “Enter” for viewing the status of the rest of the ports.
LevelOne FSW-2440TX
24-Port Smart Switch
====================
Port
13
14
15
16
17
18
19
20
21
22
23
24
---------------------------------------------------------------------------LINK
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
En
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
An
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
---
---
---
---
---
---
---
---
---
---
---
Duplex -----
---
---
---
---
---
---
---
---
---
---
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
Mirror OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Rate
---
Flow
ON
[E]:Rx/Tx Enable/Disable [A]:Auto-Negotiation [R]:Data Rate [D]:Duplex
Mode
[F]:Flow Control
[ESC]:Exit
[Enter]: Next Page
E: set port Rx/Tx ENABLE/DISABLE, the operating status of the port. Use this
screen to enable or disable the selected port. Press ‘E’ to enable Rx and Tx
or ‘D’ to disable Rx and Tx or press ‘R’ or ’T’ to change Rx/Tx current status. A
disabled port does not transmit any packets to the connected segment, nor
forward any received packets to the switching back-plane.
A: set AN function ENABLE/DISABLE, the Auto Negotiation status for the port.
Use this screen to enable or disable the Auto Negotiation function for the port.
R: set data rate 10/100, the current connection speed specified for the port.
Use this screen to set the speed of a port. Port speed can be either 100Mbps
or 10Mbps. If Auto Negotiation is enable there has no effect on the speed
selection. Force to change data rate if and only if the Auto Negotiation mode
will be disabled.
D: set duplex full/half mode, the current connection speed specified for the
port. Use this screen to set the speed of a port. Port speed can be either
100Mbps or 10Mbps. If Auto Negotiation is enable there has no effect on the
14
duplex mode selection. Force to change duplex mode if and only if the Auto
Negotiation mode will be disabled.
F: set flow control ENABLE/DISABLE, the Flow Control capability for the port.
Use this screen to enable or disable Flow Control capability of full duplex
mode for the port. The flow control result will depend on the result of Auto
Negotiation. For Smart Switch, pause enable or disable will depend on link
partner's Flow Control Capability.
6.3.1 E: Port Enable/Disable
This function can disable or enable transmit and receive of select port, default
value is port enabled.
For example: Select port#01 and press ‘D’ to disable port 1.
LevelOne FSW-2440TX
24-Port Smart Switch
====================
Set Port Rx/Tx Enable/Disable
---> Select port # : 1
Select Port is Tx/Rx Disabled now
---> [D]: Disable
[E]: Enable
[ESC]: Exit
---> Please select: D Disable.
Set Port # 01
Press 'SPACE BAR' to continue
6.3.2 A: Port AN Enable/Disable or Reset
Which indicates the current auto-negotiation status of the ports. Enable or
disable the auto-negotiation when connect with another device. The default
value is auto-negotiation enable.
For example: disable port#02’s AN function.
15
LevelOne FSW-2440TX
24-Port Smart Switch
====================
Set Port Auto-Negotiation Enable/Disable
---> Select port # : 2
---> [D]: Disable
[E]: Enable
[ESC]: Exit
---> Please select: D Disable.
Set Port # 02 Auto-Negotiation
Press 'SPACE BAR' to continue
6.3.3 R: port rate control 10/100M
Which can change data rate of the ports. Data rate is changed only when
auto-negotiation function is disabled. The default value of data rate is 10Mb.
For example: force port#03’s data rate to 10Mb.
LevelOne FSW-2440TX
24-Port Smart Switch
====================
Set Data Rate 100Mb/10Mb
---> Select port # : 3
Warnning : Auto-Negotiation is Enable on this port
force to change will disable AN !
---> [0]: 10Mb
[1]: 100Mb
[ESC]: Exit
---> Please select: 0 Speed 10Mb.
Set Port # 03
Press 'SPACE BAR' to continue
6.3.4 D: Port duplex mode Half/Full
Which can force full/half duplex mode of the ports. Duplex mode is changed
only when the corresponding port’s auto-negotiation function is disabled. The
default value of duplex mode is half duplex mode.
For example: set port#04 to half duplex mode.
16
LevelOne FSW-2440TX
24-Port Smart Switch
====================
Set Port Duplex Mode
---> Select port # : 4
Warnning : Auto-Negotiation is Enable on this port
force to change will disable AN !
---> [F]: Full duplex
[H]: Half duplex
[ESC]:Exit
---> Please select: H Half Duplex Mode.
Set Port # 04
Press 'SPACE BAR' to continue
6.3.5 F: Flow control enable/disable
Which can show and set the flow control capability of the ports. The default
value for flow control capability is enabled.
For example: disable port#5’s flow control capability.
LevelOne FSW-2440TX
24-Port Smart Switch
====================
Set Port Flow Control Capability
---> Select port # : 5
---> [E]: Enable flow control capability
[D]: Disable flow control capability
[ESC]:Exit
NOTE : flow control capability only apply to full-duplex mode
---> Please select: D Flow Control Capability Disable.
Set Port # 05
Press 'SPACE BAR' to continue
NOTE: Until the cables connect to the corresponding ports (it means the LINK
status should display as UP), the port status shown above are now ineffective.
If Auto-Negotiation is enable, the function has no effect on the speed
selection and duplex-mode setting.
17
After change the port control configuration, the brief summary status will show
as below.
LevelOne FSW-2440TX
24-Port Smart Switch
====================
Port
01
02
03
04
05
06
07
08
09
10
11
12
---------------------------------------------------------------------------LINK
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
En
ON
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
An
ON
ON
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
---
100
10
100
---
---
---
---
---
---
---
Duplex -----
H
H
H
---
---
---
---
---
---
---
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
Mirror OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Rate
---
Flow
ON
[E]:Rx/Tx Enable/Disable [A]:Auto-Negotiation [R]:Data Rate [D]:Duplex
Mode
[F]:Flow Control
[ESC]:Exit
[Enter]: Next Page
6.4 Mirror Function
With the Port Mirror Control, you can perform the following:
P: set Port mirror status
R: Reset all mirror Configure
I: Ingress rule Configure
E: Egress rule Configure
18
LevelOne FSW-2440TX
24-Port Smart Switch
====================
Port
01
02
03
04
05
06
07
08
09
10
11
12
-----------------------------------------------------------------------------OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Port
13
14
15
16
17
18
19
20
21
22
23
24
-----------------------------------------------------------------------------OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
No Capture Port select!
Ingress Filter : All frames
MAC : 00-00-00-00-00-00
00-00-00-00-00-00
Divider : 00000
Egress Filter : All frames
MAC :
Divider : 00000
[P]: set Port mirror status, [R]: Reset all mirror Configure
[I]: Ingress rule Configure, [E]: Egress rule Configure
[ESC]:Exit
[ ]
6.4.1 P: set Port mirror status
P: set port mirror status to be the capture port or mirror ingress, egress or
both ingress and egress frames on the selected port.
After select one port, you have 5 settings to the selected port.
C: set the Capture port.
B: mirror both Ingress and Egress frames of the selected port.
O: set to OFF.
I: only mirror ingress frames.
E: only mirror egress frames.
For example: Set port#01 as capture port and mirror both ingress and egress
frames of port#02.
Choose port#01 as Mirror Capture Port.
19
Port
01
02
03
04
05
06
07
08
09
10
11
12
-----------------------------------------------------------------------------OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Port
13
14
15
16
17
18
19
20
21
22
23
24
-----------------------------------------------------------------------------OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
No Capture Port select!
Ingress Filter : All frames
MAC : 00-00-00-00-00-00
00-00-00-00-00-00
Divider : 00000
Egress Filter : All frames
MAC :
Divider : 00000
[P]: set Port mirror status, [R]: Reset all mirror Configure
[I]: Ingress rule Configure, [E]: Egress rule Configure
[ESC]:Exit
[P]
[C]
---> Please select port : 1
---> [C]: Capture,
[B]: In/Egress. [O]: Off
[I]: Ingress only, [E]: Egress only [ESC]:Exit
You can see Port 1 is marked as “CAP”
LevelOne FSW-2440TX
24-Port Smart Switch
====================
Port
01
02
03
04
05
06
07
08
09
10
11
12
-----------------------------------------------------------------------------CAP OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Port
13
14
15
16
17
18
19
20
21
22
23
24
-----------------------------------------------------------------------------OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Ingress Filter : All frames
MAC : 00-00-00-00-00-00
00-00-00-00-00-00
Divider : 00000
Egress Filter : All frames
MAC :
Divider : 00000
[P]: set Port mirror status, [R]: Reset all mirror Configure
[I]: Ingress rule Configure, [E]: Egress rule Configure
[ESC]:Exit
[ ]
20
Choose port#02 as mirrored port for both ingress and egress frames.
Port
01
02
03
04
05
06
07
08
09
10
11
12
-----------------------------------------------------------------------------CAP OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Port
13
14
15
16
17
18
19
20
21
22
23
24
-----------------------------------------------------------------------------OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Ingress Filter : All frames
MAC : 00-00-00-00-00-00
00-00-00-00-00-00
Divider : 00000
Egress Filter : All frames
MAC :
Divider : 00000
[P]: set Port mirror status, [R]: Reset all mirror Configure
[I]: Ingress rule Configure, [E]: Egress rule Configure
[ESC]:Exit
[P]
[B]
---> Please select port : 2
---> [C]: Capture,
[B]: In/Egress. [O]: Off
[I]: Ingress only, [E]: Egress only [ESC]:Exit
You can see Port 2 is marked as “I/E”
21
LevelOne FSW-2440TX
24-Port Smart Switch
====================
Port
01
02
03
04
05
06
07
08
09
10
11
12
-----------------------------------------------------------------------------CAP I/E
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Port
13
14
15
16
17
18
19
20
21
22
23
24
-----------------------------------------------------------------------------OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Ingress Filter : All frames
MAC : 00-00-00-00-00-00
00-00-00-00-00-00
Divider : 00000
Egress Filter : All frames
MAC :
Divider : 00000
[P]: set Port mirror status, [R]: Reset all mirror Configure
[I]: Ingress rule Configure, [E]: Egress rule Configure
[ESC]:Exit
[ ]
6.4.2 R: Reset all mirror Configure
R: Reset all mirror Configure, use this function to disable all mirror
configuration.
6.4.3 I/E: Ingress/Egress rule Configure
I/E: Ingress/Egress mirror rule Configure, use this function to select mirror
rules of all system.
After you press “I” or “E”, you have 5 settings to Ingress or Egress.
P: mirror all port's frames
Press ‘P‘ to monitor all frames of all ports that are set as Ingress/Egress
ports.(default will mirror all frames of selected ports)
D: mirror Dest. MAC Address
Select ‘D’ to mirror all Ingress/Egress frames that has specific Destination
MAC Address(Setup in ‘M’ enter MAC Address) of all ports that be chosen set
as Ingress/Egress ports.
S: mirror Source MAC Address
Select ‘S’ to mirror all Ingress/Egress frames that has specific Source MAC
Address(Setup in ‘M’ enter MAC Address) of all ports that be chosen as
22
Ingress/Egress ports.
M: enter MAC Address
Press ‘M‘ to setup the MAC Address.
V: set Divider
Press ‘V‘ to set Ingress/Egress mirror divider. The value indicates
receive/transmit frames that have passed the device and divided by the value
only one in n frames.
Port
01
02
03
04
05
06
07
08
09
10
11
12
-----------------------------------------------------------------------------CAP OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Port
13
14
15
16
17
18
19
20
21
22
23
24
-----------------------------------------------------------------------------OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Ingress Filter : All frames
MAC : 00-00-00-00-00-00
00-00-00-00-00-00
Divider : 00000
Egress Filter : All frames
MAC :
Divider : 00000
[P]: set Port mirror status, [R]: Reset all mirror Configure
[I]: Ingress rule Configure, [E]: Egress rule Configure
[ESC]:Exit
[I]
[ ]
---> [P]: mirror all port's frames
[D]: mirror Dest. MAC Address
[S]: mirror Source MAC Address
[M]: enter MAC Address
[V]: set Divider
[ESC]: Exit
NOTE:
1. Only one port can be chosen as capture port at the same time.
2. Mirror multi-ports is possible but can create congestion at the mirror
capture port.
3. The Ingress/Egress mirror divider indicate that all frames pass to/through
the device will be captured to the monitor port in n frames, the n value will
display in decimal and the range is from 0 to 1023.
6.5 VLAN Function
Every time select this submenu, we have to check whether to reset the
original VLAN Configure. Select (Y)es to reset VLAN group. It means that
system will clear all VLAN group after select (Y)es.
23
LevelOne FSW-2440TX
24-Port Smart Switch
====================
VLAN\Port
01
02
03
04
05
06
07
08
09
10
11
12
----------------------------------------------------------------------------[ V01 ] :
V
V
V
V
V
V
V
V
V
V
V
V
[ V02 ] :
[ V03 ] :
[ V04 ] :
[ V05 ] :
VLAN\Port
13
14
15
16
17
18
19
20
21
22
23
24
----------------------------------------------------------------------------[ V01 ] :
V
V
V
V
V
V
V
V
V
V
V
V
[ V02 ] :
[ V03 ] :
[ V04 ] :
[ V05 ] :
Reset Vlan ? (Y)es/(N)o
In this feature, user can set up five VLAN groups.
LevelOne FSW-2440TX
24-Port Smart Switch
====================
VLAN\Port
01
02
03
04
05
06
07
08
09
10
11
12
----------------------------------------------------------------------------[ V01 ] :
V
V
V
V
V
V
V
V
V
V
V
V
[ V02 ] :
[ V03 ] :
[ V04 ] :
[ V05 ] :
VLAN\Port
13
14
15
16
17
18
19
20
21
22
23
24
----------------------------------------------------------------------------[ V01 ] :
V
V
V
V
V
V
V
V
V
V
V
V
[ V02 ] :
[ V03 ] :
[ V04 ] :
[ V05 ] :
[TAB]: Next Item
[BACKSPACE]: Back [ENTER]: Toggle
[Number Key]: Which Row [ESC]: Exit
Press Number “1” to “5” for selecting VLAN group.
Press “Tab” for moving to next port and “Enter” to Enable or Disable VLAN of
the port.
Press “Back Space” for moving to pre-port.
Note: Each port has to set to its belonging VLAN group, or it will be
considered as one independent VLAN group. For example, it can not
24
communicate with each other.
6.6 QOS Function
With the System Submenu, you can perform the following:
E/D: enable/disable port base setting. Set Enable will open all QOS Functions.
It means the device will have such ability to receiving 802.1p frames and
accept the Configure under below setting.
T: Setting TCI THRESHOLD of 802.1p frame. If 802.1p frame pri[2:0 >= TCI
THRESHOLD. Then it will be qualified as high priority frame.
W: Setting the high/low priority queue weighting.
P: Port Based setting. Set high or low priority to decided ports.
6.6.1 T: TCI THRESHOLD.
Change the threshold for 802.1p frame. If 802.1p frame pri[2:0] >= TCI
THRESHOLD then it will be qualified as high priority frame.
The default TCI THRESHOLD is 4. When an incoming 802.1p priority tag
value is greater than or equal to 4, the incoming packet will be classified as
high priority.
LevelOne FSW-2440TX
24-Port Smart Switch
====================
Current TCI THRESHOLD is : 04
(default:4, pri[2:0]>=TCI THRESHOLD will be qualified as high priority
frame)
Change TCI THRESHOLD : 4
802.1p frame pri[2:0] >= 04 will be qualified as high priority frame!
Press 'SPACE BAR' to continue
6.6.2 W: Set High/Low queue weight.
Set high queue to "15" and low queue to "1". It means the system will transmit
15 packets in high queue then transmit 1 packet in low queue. You must set
up Hign/Low queue weight respectively.
25
LevelOne FSW-2440TX
24-Port Smart Switch
====================
High/Low Queue Weight : 15 : 01
Select (H)igh queue weight / (L)ow queue weight : H
Change the weight value ( 0 ~ 15, 0: Lowest, 15: Highest) : 15
6.6.3 P: Port Based Qos.
Set decided port as high or low priority port. If set Port 1 as high priority port,
it means all packets received by port 1 will be treat as high priority packets.
LevelOne FSW-2440TX
24-Port Smart Switch
====================
[Port Base QOS]
Port
01
02
03
04
05
06
07
08
09
10
11
12
----------------------------------------------------------------------------Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
Port
13
14
15
16
17
18
19
20
21
22
23
24
----------------------------------------------------------------------------Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
[TAB]: Next Item
[BACKSPACE]: Back [ENTER]: Toggle
[Number Key]: Which Row [ESC]: Exit
6.7 Trunking Function
With the System Submenu, you can perform the following:
26
LevelOne FSW-2440TX
24-Port Smart Switch
[ Chip 00 : Disable Trunking ]
Trunk\Port
09
10
11
12
21
22
23
24
----------------------------------------------------------------------------T_G[01]
T_G[02]
T_G[03]
T_G[04]
[ Chip 01 : Disable Trunking ]
Trunk\Port
05
06
07
08
17
18
19
20
----------------------------------------------------------------------------T_G[05]
T_G[06]
T_G[07]
T_G[08]
[ Chip 02 : Disable Trunking ]
Trunk\Port
01
02
03
04
13
14
15
16
----------------------------------------------------------------------------T_G[09]
T_G[10]
T_G[11]
T_G[12]
Select Chip (0~2):
Select Chip: select chip number. It means the specific chip will have such
ability of port trunking after setting Trunk group and Forwarding table.
After you select one chip, you can press “E” or “D” to Enable or Disable the
Trunking function to the selected chip.
LevelOne FSW-2440TX
24-Port Smart Switch
[ Chip 00 : Disable Trunking ]
Trunk\Port
09
10
11
12
21
22
23
24
----------------------------------------------------------------------------T_G[01]
T_G[02]
T_G[03]
T_G[04]
[ Chip 01 : Disable Trunking ]
Trunk\Port
05
06
07
08
17
18
19
20
----------------------------------------------------------------------------T_G[05]
T_G[06]
T_G[07]
T_G[08]
[ Chip 02 : Disable Trunking ]
Trunk\Port
01
02
03
04
13
14
15
16
----------------------------------------------------------------------------T_G[09]
T_G[10]
T_G[11]
T_G[12]
Select Chip (0~2): (E)nable/(D)isable Trunking
For the selected chip, you can now set up the Trunking port.
T: Setting trunk group. Per chip provide 4 trunk groups and there are at least
27
two ports in one trunk group.
F: Assign forwarding table.
LevelOne FSW-2440TX
24-Port Smart Switch
====================
[ Chip 00 : Enable Trunking ]
Trunk\Port
09
10
11
12
21
22
23
24
----------------------------------------------------------------------------T_G[01]
T_G[02]
T_G[03]
T_G[04]
Set (T)runk group or (F)orwarding table :
For example: Select Trunk group 1 and choose port 9, 10, 21, 22 as a
trunking port.
1. Select Chip 0 and Enable the trunking function.
LevelOne FSW-2440TX
24-Port Smart Switch
[ Chip 00 : Disable Trunking ]
Trunk\Port
09
10
11
12
21
22
23
24
----------------------------------------------------------------------------T_G[01]
T_G[02]
T_G[03]
T_G[04]
[ Chip 01 : Disable Trunking ]
Trunk\Port
05
06
07
08
17
18
19
20
----------------------------------------------------------------------------T_G[05]
T_G[06]
T_G[07]
T_G[08]
[ Chip 02 : Disable Trunking ]
Trunk\Port
01
02
03
04
13
14
15
16
----------------------------------------------------------------------------T_G[09]
T_G[10]
T_G[11]
T_G[12]
Select Chip (0~2): (E)nable/(D)isable Trunking
2. Select Trunk group 1 and choose port 9, 10, 21, 22 as a trunking port.
28
LevelOne FSW-2440TX
24-Port Smart Switch
====================
[ Chip 00 : Enable Trunking ]
Trunk\Port
09
10
11
12
21
22
23
24
----------------------------------------------------------------------------T_G[01]
V
V
V
V
T_G[02]
T_G[03]
T_G[04]
Set (T)runk group or (F)orwarding table :T
[TAB]: Next Item
[BACKSPACE]: Back [ENTER]: Toggle
[Number Key]: Which Row [ESC]: Exit
3. Set Forwarding Table. All Ports except trunking ports have to assign one
forwarding table.
For example:
Select (F)orwarding table for Trunk Group 1.
LevelOne FSW-2440TX
24-Port Smart Switch
====================
[ Chip 00 : Enable Trunking ]
Trunk\Port
09
10
11
12
21
22
23
24
----------------------------------------------------------------------------T_G[01]
V
V
V
V
T_G[02]
T_G[03]
T_G[04]
Set (T)runk group or (F)orwarding table :F
Select Trunk Group :1
You can set port 1, 5, 9, 13, 17, 21 packet forwarding to [01] trunking port.
The rest may be deduced by analogy.
29
LevelOne FSW-2440TX 24-Port Smart Switch
[Chip 00 Trunk Group01 Forwarding Table]
Fwd\Port
01 02 03 04 05 06 07 08 09 10 11 12
----------------------------------------------------------------------------09
V
V
V
10
V
V
V
21
V
V
V
22
V
V
V
Fwd\Port
13 14 15 16 17 18 19 20 21 22 23 24
----------------------------------------------------------------------------09
V
V
V
10
V
V
V
21
V
V
V
22
V
V
V
[TAB]: Next Item
[BACKSPACE]: Back [ENTER]: Toggle
[Number Key]: Which Row [ESC]: Exit
Note: Each port only forwards to one trunking port.
6.8 Load Default
L: Load Default Settings
LevelOne FSW-2440TX
24-Port Smart Switch
====================
Waiting ... done
Note: For load default settings, it will not save the settings. You need to press
“Save” to save current settings.
6.9 Save
Save the current settings.
30
LevelOne FSW-2440TX
24-Port Smart Switch
====================
Waiting ... done
31
7
Sample Application
The optimal application for the Switch is as a "big pipe" backbone
interconnecting file servers with bandwidth-hungry workgroups, departments,
and offices.
FSW-2440TX
100BASE-TX
FSW-1640TX
100BASE-TX
Workstation with 10/100Mbps
Fast Ethernet Adapter
Workstation with 10/100Mbps
Fast Ethernet Adapter
32
8
PRODUCT SPECIFICATIONS
Model
Standards
Ports
Media Support
Bandwidth
Forwarding/Filtering
Rate
Latency
MAC Addresses
Buffer Memory
Duplex Modes
Crossover
LED Indicators
Power Supply
Power Consumption
Environment
Certifications
Dimensions
FSW-1640TX
IEEE 802.3: 10BASE-T
IEEE 802.3u: 100BASE-TX
IEEE 802.3x: Flow-Control for Full-Duplex operation
IEEE 802.1p
Sixteen port 100BASE-TX (Copper)
10BASE-T: Category 3, 4 or 5 TP
100BASE-TX: Category 5 TP
100BASE-TX: 200/100Mbps
10BASE-T: 20/10Mbps
148810 packets/second per port @ 100Mbps, maximum
14881 packets/second per port @ 10Mbps, maximum
10 µsec @100Mbps, minimum
75 µsec @ 10Mbps, minimum
4K MAC address, Self-Learning
512K Bytes Packet Memory
TP ports have 10/100Mbps Full/Half-Duplex Auto-Negotiation function
All the TP ports support Auto-MDIX function
One (1) for Power
One (1) per port for Link/ACT
One (1) per port for Full/Half-Duplex
One (1) per port for 10/100Mbps (speed)
Input voltage: 100 ~ 240 +/-10% VAC/ 50 ~ 60 Hz
16.5 watt maximum
Operating Temperature: 0° ~ 45°C (32° ~ 113°F)
Storage Temperature: -20° ~ 70°C (-4° ~ 158°F)
Humidity: 10% ~ 90% Non-Condensing
FCC Class A
CE Mark
263x187x43mm(10.4x7.4x1.7inches)
33
Model
Standards
Ports
Media Support
Bandwidth
Forwarding/Filtering
Rate
Latency
MAC Addresses
Buffer Memory
Duplex Modes
Crossover
LED Indicators
Power Supply
Power Consumption
Environment
Certifications
Dimensions
FSW-2440TX
IEEE 802.3: 10BASE-T
IEEE 802.3u: 100BASE-TX
IEEE 802.3x: Flow-Control for Full-Duplex operation
IEEE 802.1p
Twenty-Four (24) 100BASE-TX (Copper)
10BASE-T: Category 3, 4 or 5 TP
100BASE-TX: Category 5 TP
100BASE-TX: 200/100Mbps
10BASE-T: 20/10Mbps
148810 packets/second per port @ 100Mbps, maximum
14881 packets/second per port @ 10Mbps, maximum
10 µsec @100Mbps, minimum
75 µsec @ 10Mbps, minimum
4K MAC address, Self-Learning
768K Bytes Packet Memory
TP ports have 10/100Mbps Full/Half-Duplex Auto-Negotiation function
All the TP ports support Auto-MDIX function
One (1) for Power
One (1) per port for Link/ACT
One (1) per port for Full/Half-Duplex
One (1) per port for 10/100Mbps (speed)
Input voltage: 100 ~ 240 +/-10% VAC/ 50 ~ 60 Hz
16.5 watt maximum
Operating Temperature: 0° ~ 45°C (32° ~ 113°F)
Storage Temperature: -20° ~ 70°C (-4° ~ 158°F)
Humidity: 10% ~ 90% Non-Condensing
FCC Class A
CE Mark
265x185x44mm (10.4x7.3x1.7inches)
34
FCC WARNING
This equipment has been tested and found to comply with the limits for a Class A computing device pursuant
to Part 15 of FCC Rules, which are designed to provide reasonable protection against electromagnetic
interference in a commercial environment.
Changes or modifications to the equipment not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
CE MARK WARNING
This is a Class A product. In a domestic environment this product may cause radio interference in which case
the user may be required to take adequate measures.
35

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project