EmCORE-i9457 3.5” Embedded Board Quick Installation Guide Version 1.3 Form Factor CPU Chipset 3.5” Embedded Board mPGA 478 Socket for Intel® Core™ 2 Duo, Core™ Duo, Celeron M Intel® 945GME Intel® ICH7M I/O LAN Audio CF II/ Mini-PCI/ USB/ IDE/ COM/ LPT/ FDD 1 x Realtek RTL8111 PCIe GbE ALC655 AC97 codec, Line-in/out, Mic-in Video Dual Channels LVDS/ Analog RGB ♦ Technical Support If you have any technical difficulties, please consult the user’s manual first at: ftp://ftp.arbor.com.tw/pub/manual Please do not hesitate to call or e-mail our customer service when you still can not find out the answer. http://www.arbor.com.tw E-mail: [email protected] Declaration of Conformity FCC Class A This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Copyright® 2013 All Rights Reserved. 4041945700130P -1- Packing List Before you begin installing your single board, please make sure that the following materials have been shipped: 1 x EmCORE-i9457 3.5” Embedded Board 1 x Driver CD 1 x Quick Installation Guide 1 x CPU Cooler 90 x 66 x 27.8mm (W x L X H) 1 x ATX Power cable ATX main power connector (2x10-pin) to EmCORE-i9457 power connector (2x5-pin) If any of the above items is damaged or missing, contact your vendor immediately. Ordering Information EmCORE-i9457VLG CBK-08-9457-00 3.5” Intel 65nm µFC-PGA Core™ Duo/Core™ 2 Duo/ Celeron M Embedded Board 1 x Audio Cable 1 x COM Port Cable 1 x LPT to FDD Cable 1 x IDE Cable 1 x LPT Cable 1 x Keyboard & Mouse Cable 1 x SATA Cable 2 x USB Cables The Installation Paths of CD Driver Windows 2000 & XP Driver Path CHIPSET \CHIPSET\INTEL\INF 9.11 VGA \GRAPHICS\INTEL_2K_XP_32\1432 LAN \ETHERNET\REALTEK\8111_WINXP_5764 AUDIO \AUDIO\REALTEK_AC97\WINDOWS_A401\98_2K_XP Windows 7 CHIPSET \CHIPSET\INTEL\INF 9.1.1.1004 -2- VGA \GRAPHICS\INTEL_WIN7_32\1930 LAN Windows 7 built-in LAN driver AUDIO \AUDIO\REALTEK_AC97\Win7_32_64_6305 Specifications Form Factor 3.5” Embedded Board CPU Supports socket mPGA 478 for Intel® Core™ 2 Duo/ Core™ Duo/ Celeron M Chipset Intel® 945GME + Intel® ICH7M System Memory 1 x 200-pin SO-DIMM socket up to 2GB DDR2 533/667 SDRAM VGA/ LCD Controller Intel® Graphics Media Accelerator 950 graphics core w/ Analog RGB/ Dual Channels LVDS (Dual independent display) Ethernet 1 x RTL8111 PCIe GbE Controller I/O Chips WINBOND W83627HG BIOS Phoenix-Award PnP Flash BIOS Audio ALC655 AC’97 Codec, Line-in/out, Mic-in IDE Interface 1 x IDE (Ultra ATA 33), support 2 IDE devices SATA 1 x Serial ATA with 150MB/s HDD transfer rate Serial Port 2 x COM ports (1 x RS232, 1x RS232/422/485 selectable) Parallel Port/ Floppy 1 x SPP/EPP/ECP mode 1 x Floppy connector, shared with Parallel Port KBMS Standard PS/2 Keyboard and Mouse (via Y-cable) Universal Serial Bus 6 x USB 2.0 ports LCD Dual Channels LVDS Expansion Interface 1 x CF II socket, 1 x Mini-PCI socket Hardware Monitor Chip Integrated in W83627HG Operation Temp. -20oC ~ 70oC (-4oF ~ 158oF) Watchdog Timer 255-level Reset Dimension (L x W) 146 x 102 mm (5.7” x 4”) -3- 8.84 3.38 95.2 101.96 Unit: mm Board Dimension 1.6 30.1 7.59 90 29.47 47.75 10 5 3.35 41.28 42.16 28.24 103.32 132.27 115.11 22.48 32.64 mPGA478 SOCKET 1 1 + 14.61 CF 1 1 5 6 1 2 6.5 29.46 3.1 Unit: mm 5 6.3 -4- + 31.47 146 133.93 95.91 46.99 8.84 3.38 95.2 101.96 Unit: mm 1.6 30.1 7.59 90 29.47 -5- 47.75 Jumpers & Connectors 5 6 1 1 2 9 10 1 2 1 2 1 1 123 7 12 AUDIO1 JV4 15 JV3 14 124 6 3 1 9 10 1 2 9 10 1 2 1 2 JRS2 JCOM2 JSMB1 10 9 8 USB3 USB2 2 2 3 4 1 1 4 JFRT1 9 10 11 COM2 43 44 5 IDE1 16 USB1 20 17 LAN1 MINIPCI1 13 CFD1 26 1 62 SATA1 2 52 1 19 LPT1 3 002 RES1 JBAT1 19 1 DIMM1 991 18 KBM1 20 mPGA478 SOCKET VGA1 2 93 04 24 14 21 COM1 25 LVDS1 24 JVLCD1 5 10 6 1 1 29 1 1 2 30 1 INV1 1 1 05 23 22 ATX1 CPUF1 -6- LED1 Jumpers/ Connectors Quick Reference Jumpers Label Function JRS2 COM2 RS-232/422/485 Selection JV3, JV4 COM2 Power source special Support JBAT1 Clear CMOS Setting JVLCD1 LCD Panel Voltage Selection Connectors Label Function INV1 LCD Inverter Connector SATA1 SATA Connector LPT1 Parallel/FDD Port Connector JFRT1 Switches and Indicator Connector IDE1 IDE Connector USB2, USB3 USB Connectors JSMB1 External SMBus Connector JCOM2 RS-422/485 Output Connector COM2 Serial Port Connectors AUDIO1 Audio Interface Connector MINIPCI1 MiniPCI Slot USB1 Double stack USB connector LAN1 RJ-45 connector KBM1 PS/2 Keyboard and Mouse connector VGA1 CRT Connector COM1 Serial Port Connector ATX1 ATX Power Connector CPUF1 CPU Fan Connector LVDS1 LVDS LCD Connector CFD1 CompactFlash Type II Socket Switch & indicators LED1: Power/ HDD indicators LED Mode Green Power ON/ Standby Yellow HDD activity RES1: Reset Button Jumpers JRS2: COM2 RS-232/422/485 Selection (9) Connector type: 2.54mm pitch 2x3-pin headers. Mode RS-232 (Default) RS-422 RS-485 1-2 Short Open Open 3-4 Open Short Open 5-6 Open Open Short 1 2 1 2 1 2 5 6 5 6 5 6 JV3, JV4: COM2 Power source Special Support (14), (15) Connector type: 2.54mm pitch 2x3-pin headers. Setup JV3/JV4 1 2 3 POS: +5V on pin 1 JV3 JV4 1 2 3 POS: +12V on pin 9 POS: +5V on pin 1 and +12V on pin 9 JV3 JV4 1 2 3 JV3 JV4 JBAT1: Clear CMOS Setting (19) Connector type: 2.54mm pitch 1x3-pin headers Pin Mode -7- 1-2 Keep CMOS (Default) 2-3 Clear CMOS 3 3 2 1 2 1 33 22 11 JVLCD1: LCD Panel Voltage Selection (24) Parallel port connector is shared w/ FDD. Pin 1 3 5 7 9 11 13 15 17 19 The voltage of LCD panel could be selected by JVLCD1 in +5V or +3.3V. Connector type: 2.54mm pitch 1x3-pin headers. Pin Voltage 1-2 +5V 3 2 1 3 2 1 2-3 +3.3V (Default) 3 2 3 2 1 1 Connectors INV1: LCD Inverter Connector (1) Description 1 +12V 2 GND 3 Backlight on/off 4 Brightness control 5 GND 1 2 3 4 5 Description GND TX+ TXGND RXRX+ GND 1 7 LPT1: Parallel Port Connector (3) Desc. AFD ERROR INIT SLIN GND GND N/C BUSY PE SELECT 19 20 Pin 2 4 6 8 10 12 14 16 18 20 1 2 It can be selected by LPT or FDD mode via BIOS. Connector type: 2.54mm pitch 2x10-pin headers. Desc. STROBE PTD0 PTD1 PTD2 PTD3 PTD4 PTD5 PTD6 PTD7 ACK It provides connectors for system indicators that provides light indication of the computer activities and switches to change the computer status. Connector type: 2.54mm pitch 2x2-pin headers. Pin Description Pin Description 1 PWRBTN+ 2 PWRBTN- 3 RESET+ 4 RESET- 1 3 2 4 Connector type: 2.00mm pitch 2x24 box headers. High speed transfer rates (150MB/s). Pin 1 3 5 7 9 11 13 15 17 19 Desc. RWCHEADDIRSTEPGND GND N/C MOBWDWE- IDE1: Primary IDE Connector (5) SATA1: Serial ATA Connector (2) Pin 1 2 3 4 5 6 7 Pin 2 4 6 8 10 12 14 16 18 20 JFRT1: Switches and Indicators (4) Connector type: 2.00mm pitch 1x5-pin box wafer connector. Pin Desc. N/C RINDEXTRAK0WPRDATADSKCHGN/C N/C N/C DSB- Pin Description Pin Description 1 IDE RESET 2 GND 3 DATA7 4 DATA8 5 DATA6 6 DATA9 7 DATA5 8 DATA10 9 DATA4 10 DATA11 11 DATA3 12 DATA12 13 DATA2 14 DATA13 15 DATA1 16 DATA14 17 DATA0 18 DATA15 19 GND 20 N/C (Key) 21 REQ 22 GND 23 IO WRITE 24 GND 25 IO READ 26 GND 27 IO READY 28 IDESEL 29 DACK 30 GND 31 IRQ14 32 N/C 33 ADDR1 34 ATA66 DETECT 35 ADDR0 36 ADDR2 37 CS2# 38 CS3# 39 IDEACTP 40 GND 41 VCC (+5V) 42 VCC (+5V) 43 GND 44 N/C -8- 1 2 43 44 USB2, USB3: USB ConnectorS (6), (7) Each one connector supports two USB 2.0 by pin headers. Pin Desc. Pin Desc. 1 +5V 2 +5V 3 USBD1- 4 USBD2- 5 USBD1+ 6 USBD2+ 7 GND 8 GND 9 GND 10 N/C (Key) 1 2 9 10 MiniPCI1: MiniPCI slot (13) USB1: USB Connector (16) LED JSMB1: External SMBUS Connector (8) Connector type: 2.00mm pitch 1x3-pin box wafer c o n n e c t o r . Pin Description 1 Data 2 Clock 3 GND 1 2 3 87654321 USB 1 2 3 4 USB LAN1 supports one 10/100/1000 base-T Ethernet. Connector type: RJ-45. LED RS-422 TX+ DATA+ 2 TX- DATA- 3 RX+ N/C 4 RX- N/C 87654321 1 2 3 4 RS-485 1 1 2 3 4 Mini-Din Keyboard & Mouse connector 1 2 3 4 Pin Description 1 KB Data 2 MS Data 3 GND Connector type: 2.54mm pitch 2x5-pin box headers. 4 +5V Pin Desc. Pin Desc. 1 DCD# 2 RXD 5 KB Clock 3 TXD 4 DTR# 6 MS Clock 1 2 5 GND 6 DSR# 7 RTS# 8 CTS# 9 RI# 10 N/C 6 5 4 3 2 1 VGA1: CRT Connector (20) 9 10 Connector type: D-Sub 15-pin female. AUDIO1: Audio Interface Connector (12) Connector type: 2.00mm pitch 2x5-pin headers Pin USB KBM1: Keyboard & USB Mouse (18) COM2: Serial port Connector (11) Desc. LED LAN Connector type: 2.54mm pitch 1x4-pin box wafer connector. Pin 1 2 3 4 LAN1: LAN Connector (17) JCOM2: RS-422/485 Output Connector (10) Pin LED USB1 supports two USB 2.0 connectors w/ 480MB/s. LAN Connector type: Double stack USB type A. Desc. Pin Desc. Pin Desc. 1 RED 9 VCC 2 GREEN 10 GND 3 BLUE 11 N/C 1 Line Left in 2 Line Right in 4 N/C 12 D-DATA 3 GND 4 GND 5 GND 13 H-SYNC 5 MIC1 6 MIC2 6 GND 14 V-SYNC 7 GND 8 GND 7 GND 15 D-DCLK 9 Line Out Left 10 Line Out Right 8 GND -9- 1 11 5 15 COM1: RS-232 Connector (21) LVDS1: LVDS LCD Connector (25) Connector type: DF-13-30DP-1.25V connector. Connector type: D-Sub 9-pin male. Pin Desc. Pin Desc. Pin Desc. Pin Desc. 1 DCD# 6 DSR# 2 VDD 1 VDD 2 RXD 7 RTS# 6 3 TXD 8 CTS# 9 4 DTR# 9 RI# 5 GND 1 5 ATX1: ATX Power Connector (22) Pin Description Pin Description 6 1 4 TX2CLK+ 3 TX1CLK+ 6 TX2CLK- 5 TX1CLK- 8 GND 7 GND 10 TX2D0+ 9 TX1D0+ 12 TX2D0- 11 TX1D0- 14 GND 13 GND 16 TX2D1+ 15 TX1D1+ 6 +5VSB 1 PS_ON 7 +5V 2 GND 18 TX2D1- 17 TX1D1- 8 +5V 3 GND 9 N/C 4 +12V 20 GND 19 GND 10 GND 5 +3.3V 10 CPUF1: CPU FAN Connector (23) 5 The fan must be a +12V fan. Connector type: 2.54mm pitch 1x3-pin wafer one wall connector. Pin Description 1 GND 1 2 +12V 3 3 Fan_Detect 2 22 TX2D2+ 21 TX1D2+ 24 TX2D2- 23 TX1D2- 26 GND 25 GND 28 TX2D3+ 27 TX1D3+ 30 TX2D3- 29 TX1D3- 2 1 30 29 CFD1: CompactFlash Type II Socket (26) After hot-swapping CF II, you must restart your system for device detecting. Default setting: IDE Master. - 10 -
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021