MODEL: M7EASV - M
MODEL: M7EASV
Super-mini Signal Conditioners with
LCD Display M7E-UNIT Series
DC ALARM
(dual or quad alarm trip)
Functions & Features
• Provides relay outputs at preset DC input levels
• Quad or dual trip
• Front LCD display indicating values in scaled engineering
unit range is used to program the module
• Adjustable deadband (hysteresis)
• Software lock
• ON delay time selectable
• Hi/Lo trip and energized/de-energized coil independently
selectable for each setpoint
• Enclosed relays
• Relays can be powered by 200 V AC and 100 V DC
• High-density mounting on DIN rail
Typical Applications
• Annunciator
• Various alarm applications
Mode
Set
[3] POWER INPUT
AC Power
M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,
47 – 66 Hz)
DC Power
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
[4] OPTIONS (multiple selections)
Standards & Approvals
blank: Without CE
/CE: CE marking
Other Options
blank: none
/Q: Option other than the above (specify the specification)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating
TERMINAL SCREW MATERIAL
/S01: Stainless steel
EX-FACTORY SETTING
/SET: Preset according to the Ordering Information Sheet
(No. ESU-7762)
Default setting will be used if not otherwise specified.
83
(3.27)
Down
2: 4 points; N.O. or make contact
3: 4 points; N.C. or break contact
5: 2 points; SPDT or transfer contact
SPECIFICATIONS OF OPTION: Q (multiple selections)
29.5
(1.16)
Up
[2] OUTPUT
124
(4.88)
mm (inch)
MODEL: M7EASV-[1][2]-[3][4]
ORDERING INFORMATION
• Code number: M7EASV-[1][2]-[3][4]
Specify a code from below for each [1] through [4].
(e.g. M7EASV-Z12-M2/CE/Q)
• Specify the specification for option code /Q
(e.g. /C01/S01/SET)
[1] INPUT
Current
Z1: Range 0 – 50 mA DC (Input resistance 100 Ω)
Voltage
S1: Range -1000 – +1000 mV DC (Input resistance 1 MΩ min.)
S2: Range -10 – +10 V DC (Input resistance 1 MΩ min.)
http://www.m-system.co.jp/
M7EASV SPECIFICATIONS
ES-7762 Rev.11 Page 1/5
MODEL: M7EASV
FACTORY DEFAULT SETTING
INPUT CALIBRATION
MOVING AVERAGE
SCALING RANGE
DECIMAL POINT
SCALING UNIT
L1 ALARM VALUE
L1 ALARM TRIP OPERATION
L1 ALARM HYSTERESIS
L1 ALARM COIL AT ALARM
L2 ALARM VALUE
L2 ALARM TRIP OPERATION
L2 ALARM HYSTERESIS
L2 ALARM COIL AT ALARM
L3 ALARM VALUE
L3 ALARM TRIP OPERATION
L3 ALARM HYSTERESIS
L3 ALARM COIL AT ALARM
L4 ALARM VALUE
L4 ALARM TRIP OPERATION
L4 ALARM HYSTERESIS
L4 ALARM COIL AT ALARM
POWER ON DELAY TIMER
ALARM ON DELAY TIMER
LATCHING
LCD CONTRAST
LCD BACK LIGHT
LCD BACK LIGHT OFF TIME
Z1: 4 - 20 mA DC
S1: 1 - 100 mV DC
S2: 1 - 5 V DC
NONE
0.0 - 100.0
XXX.X
°C
20.0
Lo alarm trip
1.0
Coil energized
80.0 (2 point alarm)
30.0 (4 point alarm)
Hi alarm trip (2 point alarm)
Lo alarm trip (4 point alarm)
1.0
Coil energized
70.0
Hi alarm trip
1.0
Coil energized
80.0
Hi alarm trip
1.0
Coil energized
5
0
Invalid
50
Off Timer
10
RELATED PRODUCTS
• PC configurator software (model: M7CFG)
Downloadable at M-System’s web site.
A dedicated cable is required to connect the module to the
PC. Please refer to the internet software download site or
the users manual for the PC configurator for applicable
cable types.
GENERAL SPECIFICATIONS
Construction: Plug-in
Connection: M3 screw terminals (torque 0.8 N·m)
Screw terminal: Chromated steel (standard) or stainless
steel
Housing material: Flame-resistant resin (black)
Isolation: Input to output to power
Programming: Front control buttons or PC software
Programmable parameters:
• Input range
• Input fine adjustments
• Moving average (None, 4, 8, 16 or 32 samples)
• Scale Range: -9999 to +9999
Unit: User specific unit programmable.
http://www.m-system.co.jp/
Decimal point position
• Alarm output (L1...L4 independently)
Setpoint (scaled value)
Trip action (Hi or Lo)
Deadband (hysteresis) (scaled value)
Relay coil (energized or de-energized)
• Power ON delay time (0 to 99 sec.)
• Alarm ON delay time (0 to 999 sec.)
• Latching or not
• LCD Contrast
Back Light (On, Off, Off timer)
• Tag name
• Alarm test
Refer to the instruction manual for details.
LCD DISPLAY
Display functions: Displays and sets measured range,
engineering unit, alarm operation
Effective visual area: Approx. 15.6 × 18.9 mm (0.61” ×
0.74”)
Number of pixels: 68 × 95 (horizontal × vertical)
Character color: Black
Backlight: LED (orange in normal status, red when an alarm
is tripped.)
Backlight life: Approx. 50 000 hours
(Expected time for the LCD brightness to be reduced by half
when the LCD is used continuously in 50 % brightness in
25°C)
LCD type: Transreflective FSTN
Display range: -9999 to +9999
Decimal point position: Selectable
Display rate: 150 msec.
INPUT SPECIFICATIONS
■ DC Current: Shunt resistor attached to the input terminals
(0.5 W)
Operational range: 0 – 70 mA DC with 100 Ω, 0.5 W
Input range: 0 – 50 mA DC
Minimum span: 2 mA
Factory default setting: 4 – 20 mA DC
Offset: Lower range can be any specific value within the
input range provided that the minimum span is maintained.
■ DC VOLTAGE
Code S1 (narrow spans)
Operational range: -1150 – +1150 mV DC
Input range: -1000 – +1000 mV DC
Minimum span: 10 mV
Factory default setting: 0 – 100 mV DC
Code S2 (wide spans)
Operational range: -11.5 – +11.5 V DC
Input range: -10 – +10 V DC
M7EASV SPECIFICATIONS
ES-7762 Rev.11 Page 2/5
MODEL: M7EASV
Minimum span: 0.1 V
Factory default setting: 1 – 5 V DC
Offset: Lower range can be any specific value within the
input range provided that the minimum span is maintained.
OUTPUT SPECIFICATIONS
■ Quad Alarm
Relay rating: 100 V AC @ 1 A (cos ø = 1)
120 V AC @ 1 A (cos ø = 1)
240 V AC @ 0.5 A (cos ø = 1)
30 V DC @ 1 A (resistive load)
Maximum switching voltage: 250 V AC or 125 V DC
(Limited to the max. voltage 150 V AC or to the use for
Measurement Category I in order to conform with EU
Directive)
Maximum switching power: 120 VA or 30 W
Minimum load: 5 V DC @ 10 mA
Mechanical life: 5 × 107 cycles
■ DUAL ALARM
Relay rating: 100 V AC @ 4 A (cos ø = 1)
120 V AC @ 4 A (cos ø = 1)
240 V AC @ 2 A (cos ø = 1)
30 V DC @ 4 A (resistive load)
Maximum switching voltage: 250 V AC or 125 V DC
(Limited to the max. voltage 150 V AC or to the use for
Measurement Category I in order to conform with EU
Directive)
Maximum switching power: 480 VA or 150 W
Minimum load: 5 V DC @ 10 mA
Mechanical life: 5 × 107 cycles
Alarm Trip Operation
• Example
L1 (3–6)
L2 (5–7)
Terminal No. in parentheses
Quad N.O. contacts (LL, L, H, HH)
ON
OFF
ON
PERFORMANCE in percentage of FS input
Setpoint accuracy (trip point accuracy): ±(0.1 % of FS + 1
digit)
Display accuracy: ±(0.1 % of FS + 1 digit)
Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)
Response time: ≤ 0.5 sec. (0 – 100 % at 90 % setpoint)
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @1 minute (input to output
to power to ground)
STANDARDS & APPROVALS
EU conformity:
EMC Directive
EMI EN 61000-6-4
EMS EN 61000-6-2
Low Voltage Directive
EN 61010-1
Measurement Category II (output)
Installation Category II (power)
Pollution Degree 2
Input or output to power: Reinforced insulation (300 V)
Input to output: Basic insulation (300 V)
(When 150 V AC max. load voltage or measurement
category I, applicable as reinforced insulation)
RoHS Directive
EN 50581
OFF
ON
OFF
L3 (5–8)
OFF
L4 (3–9)
Input
%
0
ON
50
LL
Approx. 6 VA at 264 V
•DC: Approx. 3 W
Operating temperature: -5 to +55°C (23 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Surface or DIN rail
Weight: 200 g (0.44 lb)
L
100
H
HH
Trip operation in power failure
Output code 2 : All relays turn OFF .
Output code 3: All relays turn ON .
Output code 5: Terminals 3 – 9, 5 – 8 turn ON.
INSTALLATION
Power Consumption
•AC:
Approx. 4 VA at 100 V
Approx. 5 VA at 200 V
http://www.m-system.co.jp/
M7EASV SPECIFICATIONS
ES-7762 Rev.11 Page 3/5
MODEL: M7EASV
EXTERNAL VIEW
Refer to the instruction manual for the setting procedure.
LCD Display
Mode Button
Up Button
Down Button
Up
Mode
Set Button
PC Configurator
Jack
Set
Down
DIMENSIONS unit: mm (inch)
6 (.23)
5 4
59 (2.32)
6
DIN RAIL
35mm wide
8
28.5 (1.12)
8
(.31)
11–M3
SCREW
9
72 (2.83)
83 (3.27)
36 (1.42)
3 2 1
2–4.2x5
(.17x.20)
MTG HOLE
6 (.24) deep
8 7
11 10
22 (.87)
94 (3.70)
29.5 (1.16)
124 (4.88)
[4 (.16)]
(.31)
• When mounting, no extra space is needed between units.
TERMINAL ASSIGNMENTS unit: mm (inch)
Input shunt resistor (model: REM2) attached for current input
19 (.75)
INPUT RESISTOR
(model: REM2)
3 2 1
6
9
5 4
8 7
11 10
http://www.m-system.co.jp/
M7EASV SPECIFICATIONS
ES-7762 Rev.11 Page 4/5
MODEL: M7EASV
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
■ OUTPUT CODE 3: N.C. Relay
■ OUTPUT CODE 2: N.O. Relay
+
INPUT
R
–
*
1
Low Drift
Amplifier
2
Ry
Digital
Computation
Circuit
4
CONFIGURATOR
Ry
JACK
Ry
Ry
Digital
Computation
9 L4 OUTPUT
9 L4 OUTPUT
6 L1 OUTPUT
6 L1 OUTPUT
3 COM
3 COM
8 L3 OUTPUT
8 L3 OUTPUT
7 L2 OUTPUT
7 L2 OUTPUT
5 COM
5 COM
10 U(+)
CONTROL SW
POWER
11 V(–)
Base Socket
*Input shunt resistor attached for current input.
■ OUTPUT CODE 5: SPDT Relay
■ Relay Protection
• AC Powered
9 N.C.
+
INPUT
R
–
1
*
Low Drift
Amplifier
2
4
CONFIGURATOR
Ry
6 N.O.
Inductive
Load (Coil)
L1 OUTPUT
LOAD
Digital
Computation
Circuit
Varistor or Spark
Quenching Circuit
3 COM
U
Ry
JACK
8 N.C.
7 N.O.
• DC Powered
Inductive
Load (Coil)
L2 OUTPUT
LOAD
5 COM
Diode, Varistor or
CR Circuit
10 U(+)
Digital
Computation
POWER
11 V(–)
CONTROL SW
Base Socket
*Input shunt resistor attached for current input.
Specifications are subject to change without notice.
http://www.m-system.co.jp/
M7EASV SPECIFICATIONS
ES-7762 Rev.11 Page 5/5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement