4000 S Basin Mixer Tap
4000 S Basin Mixer Tap
I & M Instructions
4000 S Basin Mixer Tap
I & M Instructions
Products available from Reliance
Thermostatic Mixing Valve
Thermostatic Shower and Brassware
4000 S
Basin Mixer Tap
Timeflow Controls
Electronic Controls
Pressure Reducing Valves
Heating Products
General Plumbing Products
Reliance Water Controls®
Worcester Road, Evesham, Worcestershire, WR11 4RA, UK
Tel: +44 (0) 1386 712 400 Fax: +44 (0) 1386 712 401
www.rwc.co.uk
Reliance Water Controls® reserves the right to make changes to the products which
may affect the accuracy of this information.
ZINS200070_001_01-11
POWERED BY
TECHNOLOGY
Unique engineering from timeflow specialists Presto
provides a reliable basin mixer control.
POWERED BY
TECHNOLOGY
4000 S Basin Mixer Tap
I & M Instructions
Description
4000 S Basin Mixer Tap
I & M Instructions
Notes
A high quality timeflow basin mixer tap featuring a self cleaning one piece
cartridge which has a 15 sec timed flow rate according to BSEN 816. The
mixer tap, blends hot and cold water to a present temperature
Specification
Connections:
Pre-set Flowrate: Minimum Pressure:
Maximum Working Pressure:
Maximum temperature:
Flow Time:
15MM
6 LPM at 1bar
0.2 bar (Remove flow regulator if below 1 bar)
6 bar
80°C
15 Seconds
Spares
Description
Basin Mixer Cartridge - 15 Sec:
POWERED BY
1
Product Code
SKIT 200 070
TECHNOLOGY
POWERED BY
TECHNOLOGY
6
4000 S Basin Mixer Tap
I & M Instructions
4000 S Basin Mixer Tap
I & M Instructions
Tap Body
Installation
Maintenance
Note: Ensure all pipework is throughly
flushed through before connection
Remove the indice from the control knob
Basin Sealing
Ring
Basin
Connect the flexible tail connections,
making sure the o-rings are fitted.
Use a 4mm allen key to remove
the retaining screw on the control know
Rubber
Gasket
Fit the rubber gasket and pipe clamp,
screw on retaining nut.
Pipe Clamp
Note: The Control knob is under
spring tension
Fit tap to basin, ensure the sealing ring
is central to the body fo the tap.
Flexible Tail
Connector
Pull away the control knob, display ring and spring
Plastic washer
Completely unscrew the nut and
temporarily re-fit the control
knob with the retaining screw.
5
Retaining Nut
Flexible Tail
Connectors
Connect the flexible tails to the 1/2"
isolating adaptor.
1/2” Adaptor
Strainer Seal
Flat-face
adaptor
Remove the complete cartridge for the tap body
POWERED BY
O-Rings
15mm
compression
isolating
valve
TECHNOLOGY
POWERED BY
Fit the strainer seals supplied to the check
valve assembly
Fit 15mm compression isolating valves
using the flat face adaptors supplied.
TECHNOLOGY
2
4000 S Basin Mixer Tap
I & M Instructions
4000 S Basin Mixer Tap
I & M Instructions
On the temperature limiter use a suitable tool to cut the temperature limiter
this should be cut to the same temperature that your hot water supply is set
to.
Commisioning
Remove the indice from the control knob
Use a 4mm allen key to remove the retaining screw on the control know
Note: The Control knob is under spring tension
Pull away the
control knob
Install the regulating section of the temperature limiter in the groove of the
display ring
Refix the control knob
Open isolators
Turn on the water supply
Operate the tap and check the water supply doesn not exceed 40°C at its max
setting.
POWERED BY
3
TECHNOLOGY
POWERED BY
TECHNOLOGY
4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement