UMG 508 UMG 508 – Multifunction power analyser

UMG 508 UMG 508 – Multifunction power analyser
UMG 508
Power quality
Colour graphical
display
Ethernet-Modbus
gateway
Ethernet connection
Graphic
programming
Alarm management
UMG 508 – Multifunction power analyser
Communication
• Profibus (DP/V0)
• Modbus (RTU, TCP, Gateway)
• TCP/IP
• BACnet (optional)
• HTTP (Homepage)
• FTP (File transfer)
• SNMP
• TFTP
• NTP (time synchronisation)
• SMTP (email function)
• DHCP
Interfaces
• Ethernet
• Profibus / RS485 (DSUB-9)
Power quality
• Harmonics up to 40th harmonic
• Short-term interruptions (> 20 ms)
• Transient recorder (> 50 μs)
• Starting currents (> 20 ms)
• Unbalance
• Full wave effective value
recording (up to 4.5 min.)
Networks
• IT, TN, TT networks
• 3 and 4-phase networks
• Up to 4 single-phase networks
8 digital inputs
• Pulse input
• Logic input
• State monitoring
• HT / LT switching
5 digital outputs
• Pulse output kWh / kvarh
• Switch output
• Threshold value output
• Logic output
Peak demand management (optional)
• Up to 64 switch-off stages
Measured data memory
• 256 MByte Flash
• 32 MB SDRAM
Accuracy of measurement
• Energy: Class 0.2S (… / 5 A)
• Current: 0.2 %
• Voltage: 0.1 %
Network visualisation software
• GridVis®-Basic (in the scope of supply)
PLC functionality
• Graphical programming
• Jasic® programming language
• Programming of threshold values etc.
UMG 508
Areas of application
• Continuous monitoring of the power quality
• Energy management systems (ISO 50001)
• Master device with Ethernet gateway for subordinate
measurement points
• Visualisation of the energy supply in the LVDB
• Analysis of electrical disturbances in the event of
power quality problems
• Cost centre analysis
• Remote monitoring in the property operation
• Use in test fields (e.g. in universities)
Main features
High quality measurement with high sampling rate
(20 kHz per channel)
Power quality
• Harmonics analysis up to 40th harmonic
• Acquisition of short-term interruptions
• Acquisition of transients
• Display of waveforms (current and voltage)
• Unbalance
• Vector diagram
Fig.: GridVis® – Graph set
User-friendly, colour graphical display with intuitive user guidance
• High resolution graphics display
• User-friendly, self-explanatory and intuitive operation
• Clear and informative representation of online graphs and
further power quality events
Modern communications architecture via Ethernet
• Ethernet interface and web server
• Faster, better cost-optimised and more reliable communication
system
• High flexibility due to the use of open standards
• Integration in PLC systems and BMS through additional
interfaces
• BACnet optionally available
2
Fig.: Large colour display, e.g. 12 monthly demand
values
UMG 508
Modbus Gateway function
• Economical connection of devices without Ethernet interface
• Integration of devices with Modbus-RTU interface possible
• Data can be scaled and described
• Minimised number of IP addresses required
Graphical programming
• Comprehensive programming options (PLC functionality)
• Jasic® source code programming
• Sustainable functional expansions far beyond pure
measurement
• Complete APPs from the Janitza library
Powerful alarm management
Fig.: GridVis® topology view
Internet
• Can be programmed via the graphic programming or Jasic®
source code
• All measured values can be used
• Can be arbitrarily, mathematically processed
• Individual forwarding via email sending, switching of digital
outputs, writing to Modbus addresses etc.
• Watchdog APP
• Further alarm management functions via GridVis®-Service alarm
management
Fig.: The alarm management system reports
events arising in good time.
Dimension diagrams
All dimensions in mm
Side view
View from below
Ethernet connection
Cut out: 138+0,8 x 138+0,8 mm
3
UMG 508
Typical connection
SPS
12
5
13
4
14
3
15
2
16
1
1
Digital Outputs 1-5
2
8
3
7
4
6
5
5
6
Digital Inputs 5-8
7
4
8
3
9
2
10
1
DSUB-9
RS485
Modbus/Profibus
Digital Inputs 1-4
UMG 508
Ethernet
RJ45
11
SPS
10/100Base-TX
Auxiliary Supply
N/-
L/+
18
17
Current Input 1-4
I2
I3
I1
PE
19
PE
PE
N
N
L1
L1
20
21
22
23
24
25
S1
S1
L2
PC
Voltage Input 1-4
V1 V2 V3 V4 Vref
I4
26
27
28
29
30
Switch
PC
31
S2
S2
S1
S2
L3
S1
S2
Device overview and technical data
UMG 508
Item number
52.21.001
52.21.002
52.21.003
Supply voltage AC
95 ... 240 V AC
44 ... 130 V AC
20 ... 50 V AC
Supply voltage DC
80 … 340 V DC
48 … 180 V DC
20 … 70 V DC
Item number (UL)
52.21.011
52.21.012
Supply voltage AC
95 ... 240 V AC
44 ... 130 V AC
Supply voltage DC
80 … 280 V DC
48 … 180 V DC
52.21.081
52.21.081
Device options
BACnet communication
52.21.081
L1 L2 L3 N PE
S1
S2
S1
S2
S2
General
Use in low, medium and high voltage networks
Accuracy voltage measurement
Accuracy current measurement
Accuracy active energy (kWh, …/5 A)
Number of measurement points per period
Uninterrupted measurement
S1
•
0.1 %
0.2 %
Class 0.2S
400
•
RMS - momentary value
Current, voltage, frequency
•
Active, reactive and apparent power / total and per phase
•
Power factor / total and per phase
•
Energy measurement
Active, reactive and apparent energy [L1, L2, L3, L4, ∑ L1–L3, ∑ L1–4]
•
Number of tariffs
8
Fig.: Current and voltage measurement
Recording of the mean values
Voltage, current / actual and maximum
•
Active, reactive and apparent power / actual and maximum
•
Frequency / actual and maximum
•
Demand calculation mode (bi-metallic function) / thermal
•
Other measurements
Operating hours measurement
Clock
Weekly timer
•
•
Jasic®
Power quality measurements
Harmonics per order / current and voltage
1st – 40th
Harmonics per order / active and reactive power
1st – 40th
4
Comment:
For detailed technical information please refer
to the operation manual and the Modbus address list
• = included - = not included
UMG 508
Distortion factor THD-U in %
•
Distortion factor THD-I in %
•
Voltage unbalance
•
Rotary field indication
•
Current and voltage, positive, zero and negative sequence component
Transients
•
> 50 µs
Error / event recorder function
•
Short-term interruptions
20 ms
Oscillogram recording (waveform U and I)
•
Full wave effective values (U, I, P, Q)
•
Under and overvoltage recording
•
Measured data recording
Fig.: Example for the configuration of current
measurement via 3 current transformers in a threephase 4-wire network on the UMG 508 display
Memory (Flash)
256 MB
Average, minimum, maximum values
•
Measured data channels
8
Alarm messages
•
Time stamp
•
Time basis average value
freely user-defined
RMS averaging, arithmetic
•
Displays and inputs / outputs
LCD colour graphical display 320 x 240, 256 colours, 6 buttons
•
Language selection
•
Digital inputs
8
Digital outputs (as switch or pulse output)
5
Voltage and current inputs
each 4
Password protection
•
Peak load management (optionally 64 channels)
•
Communication
Interfaces
RS485: 9.6 – 921.6 kbps (DSUB-9 connector)
•
Profibus DP: Up to 12 Mbps (DSUB-9-plug)
•
Ethernet 10/100 Base-TX (RJ-45 socket)
•
Protocols
Fig.: Illustration of the full wave effective values
for an event
Modbus RTU, Modbus TCP, Modbus RTU over Ethernet
•
Modbus Gateway for Master-Slave configuration
•
Profibus DP V0
•
HTTP (homepage configurable)
•
SMTP (email)
•
NTP (time synchronisation)
•
TFTP
•
FTP (File-Transfer)
•
SNMP
•
DHCP
•
TCP/IP
•
BACnet (optional)
•
ICMP (Ping)
•
Software GridVis®-Basic*1
Online and historic graphs
•
Databases (Janitza DB, Derby DB); MySQL, MS SQL with higher GridVis® versions)
•
Manual reports (energy, power quality)
•
Graphical programming
•
Topology views
•
Manual read-out of the measuring devices
•
Graph sets
•
Programming / threshold values / alarm management
Application programs freely programmable
7
Graphical programming
•
Programming via source code Jasic®
•
Technical data
Type of measurement
Constant true RMS
Up to 40th harmonic
Comment:
For detailed technical information please refer
to the operation manual and the Modbus address list.
Nominal voltage, three-phase, 4-conductor (L-N,
L-L)
417 / 720 V AC *2
Nominal voltage, three-phase, 3-conductor (L-L)
600 V AC
• = included - = not included
Measurement in quadrants
4
Networks
TN, TT, IT
Measurement in single-phase/multi-phase networks
1 ph, 2 ph, 3 ph, 4 ph and up to 4 times 1 ph
*1 Optional additional functions with the packages
GridVis®-Professional, GridVis®-Enterprise,
GridVis®-Service and GridVis®-Ultimate.
*2 With UL variants: 347/600 V
Measured voltage input
Overvoltage category
600 V CAT III
Measured range, voltage L-N, AC
(without potential transformer)
10 … 600 Vrms
5
UMG 508
Measured range, voltage L-L, AC
(without potential transformer)
18 … 1000 Vrms
Resolution
0.01 V
Impedance
4 MOhm / phase
Frequency measuring range
40 ... 70 Hz
Power consumption
approx. 0.1 VA
Sampling frequency
20 kHz / phase
External
auxiliary power
Measured current input
Rated current
1/5A
Resolution
0.1 mA
Measurement range
0.001 … 8.5 Amps
Overvoltage category
300 V CAT III
Measurement surge voltage
4 kV
Power consumption
approx. 0.2 VA (Ri = 5 MOhm)
Overload for 1 sec.
120 A (sinusoidal)
Sampling frequency
20 kHz
Digital inputs and outputs
Number of digital inputs
8
Maximum counting frequency
20 Hz
Reaction time (Jasic® program)
200 ms
Input signal present
18 ... 28 V DC (typical 4 mA)
Input signal not present
0 ... 5 V DC, current < 0.5 mA
Number of digital outputs
5
Switching voltage
max. 60 V DC, 30 V AC
Switching current
max. 50 mA Eff AC / DC
Output of voltage dips
20 ms
Pulse output (energy pulse)
max. 20 Hz
Maximum cable length
up to 30 m unscreened, from 30 m screened
Fig.: Connection of two electronic relays to digital
outputs 4 and 5
Mechanical properties
Weight
1080 g
Device dimensions in mm (H x W x D)
144 x 144 x approx. 81
Battery
Type CR1/2AA, 3 V, Li-Mn
Protection class per EN 60529
Front: IP40; Rear: IP20
Assembly per IEC EN 60999-1 / DIN EN 50022
Front panel installation
Connecting phase (U / I),
Single core, multi-core, fine-stranded
Terminal pins, core end sheath
0.2 to 2.5 mm²
0.2 to 2.5 mm²
Environmental conditions
Temperature range
Operation: K55 (-10 ... +55 °C)
Relative humidity
Operation: 0 ... 75 % RH
Operating height
0 ... 2,000 m above sea level
Degree of pollution
2
Installation position
user-defined
Electromagnetic compatibility
Electromagnetic compatibility of
electrical equipment
Directive 2004/108/EC
Electrical appliances for application within
particular voltage limits
Directive 2006/95/EC
Equipment safety
Safety requirements for electrical
equipment for measurement, regulation, control
and laboratory use –
Part 1: General requirements
IEC/EN 61010-1
Part 2-030: Particular requirements for
testing and measuring circuits
IEC/EN 61010-2-030
Noise immunity
Class A: Industrial environment
IEC/EN 61326-1, EMV-ILA Version 01-03
Electrostatic discharge
IEC/EN 61000-4-2
Voltage dips
IEC/EN 61000-4-11, EMV-ILA V01-03
Emissions
Class B: Residential environment
IEC/EN 61326-1, EMV-ILA Version 01-03
Radio disturbanc voltage strength 30 – 1000 MHz
IEC/CISPR11/EN 55011
Radiated interference voltage 0.15 – 30 MHz
IEC/CISPR11/EN 55011
Radiated interference voltage 9 – 150 kHz
EMV-ILA V01-03
Safety
Europe
CE labelling
USA and Canada
UL variants available
Firmware
Firmware update
6
Update via GridVis® software.
Firmware download (free of charge) from
the website:
http://www.janitza.com
Comment:
For detailed technical information please refer
to the operation manual and the Modbus address list.
• = included - = not included
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement