T170 HydroSeeder - Finn Corporation

T170 HydroSeeder - Finn Corporation
9281 LeSaint Drive • Fairfield, Ohio 45014
Phone (513) 874-2818 • Fax (513) 874-2914
Sales: 800-543-7166
T170 HydroSeeder ®
Parts and Operator’s Manual
Model SL
LBT170-SL
Serial No. _____________
NOTES
INDEX
SAFETY FIRST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SAFETY SUMMARY SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
OPERATION & MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-38
Definition of HydroSeeding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
The Finn HydroSeeder® & How It Works . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Mounting The HydroSeeder® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Dimensions, Capacities & Truck Requirements. . . . . . . . . . . . . . . . . . . . . . 6-8
Truck Mounting Calculations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
General Mounting Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Attachments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Pre-Start Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Equipment Check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
Two Valve Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11
1. Discharge Through Boom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
2. Extension Hose Through Boom . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
3. Extension Hose or Hose Reel Through Remote Port . . . . . . . . 11-12
Starting Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Area Coverage - Material Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13
Tank Capacity Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Loading (For Wood Fiber Mulch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-16
Prior to Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Discharge Nozzle Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Application of Slurry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-19
I. General Application Techniques . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
II. Discharge Through the Boom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
III. Procedures When Using Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . 17-19
A. Pump Take-Off System or Hose Reel w/Remote Valve . . . . . . 18
B. Extension Hose System w/o Remote Valve . . . . . . . . . . . . . . . 18
C. Hose Work w/Radio Remote. . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Reloading Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Liming w/The HydroSeeder®. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-20
Troubleshooting Your HydroSeeder® . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-24
Cleaning and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25
After First 4-8 Hours of Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Daily. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25
Weekly or Every 40 Hours of Operation . . . . . . . . . . . . . . . . . . . . . . . . . 25
Seasonal and Winter Storage Maintenance . . . . . . . . . . . . . . . . . . . . . . 25
Continued . . .
HydroSeeder® is a registered trademark of the Finn Corporation
INDEX CONTINUED
OPERATION & MAINTENANCE Cont'd . . .
Hydraulic System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Lubrication Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-27
Clump Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-29
Clump Maintenance Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-31
Clump Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32-33
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-38
PARTS SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39-80
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Pictorial Reference. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Structure & Railing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42-43
Hatch Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44-45
Discharge Boom Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46-47
Engine & Radiator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-49
Engine Sheet Metal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-51
Air Intake & Exhaust Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52-53
Electrical System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54-55
Clump, Piping & Discharge Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 56-57
Clump Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58-59
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60-61
Control Box Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62-63
Agitator & Seal Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64-65
Hydraulic System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66-67
Hydraulic Agitator Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Discharge Hose Extensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Hose Reel Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70-71
Decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72-73
Recommended Spare Parts & Repair Kits . . . . . . . . . . . . . . . . . . . . . . . . . .74
Tool Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76-77
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
WARRANTY REGISTRATION CARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79-80
SAFETY FIRST
With any piece of equipment, new or used, the most important
part of its operation is SAFETY!
Finn Corporation encourages you and your employees to
familiarize yourselves with your new equipment and to stress
safe operation.
The first five pages of this manual are a summary of all the
main safety aspects associated with this unit. Be sure to read
completely before operation of machine.
This symbol is used throughout the operation and
maintenance sections of this manual to call attention to safety procedures.
- Pay Attention -
DANGER:
Immediate hazards which WILL result in severe personal injury or
death.
WARNING:
Hazards or unsafe practices which COULD result in severe personal
injury or death.
CAUTION:
Hazards or unsafe practices which COULD result in minor personal
injury or product or property damage.
IMPORTANT:
Indicates that equipment or property damage could result if instructions
are not followed.
NOTE:
Gives helpful information.
Finn Corporation
CALIFORNIA
CALIFORNIA
Proposition 65 Warning
Proposition 65 Warning
The engine exhaust and some of its
constituents are known to the State
of California to cause cancer, birth
defects, and other reproductive harm.
Battery posts, terminals and related
accessories contain lead and lead
compounds, chemicals known to the
State of California to cause cancer
and reproductive harm. Wash hands
after handling.
1
HYDROSEEDER® SAFETY SUMMARY SECTION
It is important that all operators of this machine are familiar with all of the safety aspects covered in this section
and have read the entire Operator’s Manual before operating the machine. Always keep a copy of this manual
with the machine. It is the responsibility of the operator of the machine to fully understand this safety summary
section. Remember that YOU are the key to safety. Good safety practices protect not only you but also the
people working with and around you. Keep in mind that this safety section is written for this type of machine
only. Practice all other usual and customary safe working precautions; and above all, remember that safety is
up to you.
The FINN HydroSeeder® is designed to mix and apply water, seed, fertilizer, agricultural lime and hydraulic
mulch to the prepared seedbed. The resultant slurry from mixing one or more of the above materials may react
causing harmful or deadly gasses within the tank. Heat, evaporation or extended emptying period can/will
accelerate the formation of these gasses. Please contact your supplier(s) of these slurry components regarding
their potential reactivity.
I. PRE-START EQUIPMENT CHECK (equipment
check is to be made with the engine off):
II. MACHINE OPERATION:
2. If HydroSeeder® is a trailer unit, check hitch and hitch
bolts, lights, brakes and all safety components.
1. Always wear safety goggles
when operating the machine.
Other safety attire such as
safety shoes, ear protection, gloves, hard hats, dust
masks, etc. should be worn
as required by warning decals
on machine, operator’s manuals or job site requirements.
Remove rings, watches, etc.
Avoid loose fitting clothing that may get caught in rotating machinery.
3. Make sure loading hatch bag cutter is in place and
secure.
2. Do not operate the machine
without all guards in place.
1. If you have a chassis mounted unit, check devices securing HydroSeeder® to the
truck or trailer frame.
4. Check that all guard railing is in place and secure.
5. Verify that all guards are in place.
6. With the ignition switch on, verify that the signal horn is
operating correctly.
7. By carefully looking down through the loading hatch,
inspect the slurry tank for foreign objects. Never enter
the tank without following the procedures described in
#3 of the Maintenance section in this safety summary.
8. Remove unnecessary objects (or material) from the
tank top.
9. Make sure no one is working on or inside the machine.
Signal “All Clear” before starting the engine.
10. Inspect all hydraulic hoses for cracks, bulges or damage. If hoses are bad replace immediately.
11. Inspect all discharge hoses for cracks, bulges or damage. If hoses are bad replace immediately.
2
3.
Do not load unit while in transit. Load only when
parked and unit is as level as possible. Take care not
to drop pens, lighters, etc. or pieces of paper or plastic
bags into the tank, as these objects might plug the
slurry system. Should any object be dropped into the
tank, do NOT reach into the tank to retrieve the foreign
object. See #3 under Maintenance on Page 4 before
allowing any personnel to enter the tank.
4. Make sure area to be sprayed is clear of all persons,
animals, etc.
5. The driver of the carrying or towing vehicle is responsible for the safety of the operator(s) of the machine.
Make sure the driver is aware and avoids all possible
hazards to the operator(s) of the machine, such as
low tree limbs, low power lines, etc. Vehicles on which
equipment is mounted or towed must be stopped and
started gradually. Avoid abrupt starts or stops. Never
operate on a slope or a hill that may endanger the
driver and/or the operator(s). All personnel should
review and be familiar with stop/start signals between
the driver and operator(s) before going into operation.
Only the operator should be located on the platform
during operation.
6. Operator(s) of equipment
should never ride on the
machine at speeds of greater
than 5 MPH (8 kmh).
7. Never operate machine in
an enclosed area without
venting the engine exhaust
of both the equipment and
vehicle on which the equipment is mounted. Deadly
carbon monoxide fumes can
accumulate.
8. Never operate this or any other machinery when
fatigued, tired, under the influence of alcohol, illegal
drugs or medication. You must be in good physical
condition and mentally alert to operate this machine.
9. Never modify the machine. Never remove any part
of the machine (except for service and then reinstall
before operating).
10. Use proper means (steps,
ladder) for mounting and
dismounting of the machine.
Never mount or dismount a
moving machine.
III. SLURRY APPLICATION:
1. Do not aim discharge spray
toward power-lines, transformers, or other high voltage
electrical conductors. Also
do not aim discharge spray
towards people, animals
or anything other than the
intended application area.
2. Never engage the clutch
when both the recirculation
and discharge valves are
closed. Operation with both
valves closed will result in
extreme heat generation that
could cause severe bodily
injury and damage to the
equipment.
3. Recirculation valve must be open and material flowing back into the tank when using the remote valve. A
closed or plugged recirculation line will cause extreme
heat in the pump or discharge lines which will result in
severe bodily injury and damage to the equipment.
4. During application through a hose, high pressure
can be exerted at the end of the hose. Hose holding
personnel must establish good footing. The operator
should apply gradual pressure to the hose only after
hose holding personnel are firmly positioned and have
firm control of the hose. Additional personnel to direct
hose may be necessary if working on slopes. The
proper technique for hose holding personnel is to firmly
grasp the hose over the shoulder or under both arms.
Never hold the hose so it goes between the legs. If the
hose holding personnel finds that it is uncomfortable
for him to handle the hose by himself additional hose
holders should be positioned at the end of the hose.
5. Plan application so that the furthest area is covered
first; working back toward the HydroSeeder®, so that
the individuals are not walking back over slippery
ground.
6. Before opening any valves
or pipe clamps shut machine
down and check if material in
the pipe is hot. If hot, do NOT
open valve or pipe clamps as
the hot material may cause
severe personal injury. Allow
to cool and open with caution.
7. Except when loading materials, keep loading hatch lid
closed to protect operator and prevent splashing of wet
material onto the tank top.
8. Wash off spillage of slippery mulch or slurry additive
from the tank top and platform before operating equipment.
3
MAINTENANCE:
1. Before servicing the machine,
turn off engine and allow all
moving parts to stop. To prevent accidental starting disconnect battery cables. Tag
the engine operating area
to show that the machine is
being serviced. Use lockout/
tagout procedure (OSHA 29
CFR 1910.147).
2. Certain hydroseeding amendments, when combined
with or without the addition of water or heat or the
element of time, may react causing harmful or deadly
gasses! Consult your material suppliers regarding
reactivity information. The slurry tank must be flushed
and drained after each day of operation.
3. Your slurry tank may be considered a confined space
by OSHA under 29 CFR
1910.146. Before entering
any confined space, your
company must develop a
procedure for safe entry.
Make sure your company’s
plan meets all the requirements of 29 CFR 1910.146. including the following:
a)
Drain, flush and ventilate tank interior.
b)
Turn off engine and disconnect battery cables
and perform lockout/tagout procedures. (29 CFR
1910.147)
c)
Provide continuous ventilation or proper breathing
apparatus.
d)
If tank must be entered, personnel entering the
tank must be tethered to a lifeline.
e)
Provide stand-by individual outside of tank able to
communicate with person inside and able to haul
him out with lifeline if necessary.
4. Before loosening any clamps
or opening any valves, determine if material in the line is
hot by feeling the pipe. Do
NOT allow material to come
in contact with personnel.
Severe bodily injury could
result.
5. On trailer units, perform general maintenance such as
checking the safety chains, hitch and hitch bolts, tires,
brakes. Repair or replace if worn or broken. Never
operate machine on improperly inflated or damaged
tires. Always use a safety cage or cable restraints when
re-inflating a repaired tire.
4
6.
Radiator maintenance: Liquid cooling systems build
up pressure as the engine gets hot. Before removing
radiator cap, stop the engine and let the system cool.
Remove radiator cap only after the coolant is cool.
7. Battery maintenance: Lead-acid batteries contain sulfuric acid, which damage eyes of skin on contact.
Always wear a face shield to avoid acid in the eyes.
If acid contacts the eyes, flush immediately with clean
water and get medical attention. Wear rubber gloves
and protective clothing to keep acid off skin. Lead-acid
batteries produce flammable and explosive gasses.
Keep arcs, sparks, flames and lighted tobacco away.
8. Filling of fuel: Never fill the tank with the engine running, while smoking or when near an open flame.
Never smoke while handling fuel or working on the fuel
system. The fumes in an empty container are explosive. Never cut or weld on fuel lines, tanks or containers. Move at least 10 feet (3 meters) away from fueling
point before starting engine. Wipe off any spilled fuel
and let dry before starting engine.
NOTE: Be careful not to allow fuel, lubricant, hydraulic fluid or cooling fluids to penetrate into
the ground or be discharged into the water
system. Collect all fluids and dispose of them
properly.
9. It is recommended that only authorized genuine FINN
replacement parts be used on the machine.
10. Do not use either cold start fluid if engine is equipped
with glow plug type preheater or other intake manifold
type preheater. It could cause an explosion or fire and
severe injury or death.
11. Diesel fuel or hydraulic fluid under pressure can penetrate the skin or eyes and cause injury, blindness or
death. Pressure may build up in the hydraulic system;
use caution when removing the cap.
12. Make certain that all decals on the machine are maintained in good legible condition. Replacement decals
are available through Finn Corporation by specifying
part number shown in the lower right hand corner of
the decal. See page 5 for the current safety decals
mounted on the unit. See pages 74-75 in the Parts
Manual for the location and quantity of all decals on
this unit.
CURRENT SET OF SAFETY DECALS
�������
�������
�����������������������
���������������������������������
���������������������
��������������������������������������������
�������������������������������������������������
�����������������������������������������������������������������������
���������������������������������������������������������������������������
�����������������������������������������������������������
��������������
�������
������������������
������������������������
����������������������
�����������
�����������������������
�����������������������������������������������
���������������������������������������������������������
�����������������������
�������������������
���������������
������������
��������
���������
�������������
�����������������
�����������������������
������������������������������������������������
�����������������������������������������������������������������������
�����������������
��������������
�������������������������������������
����������������������������������������������������������
��������
���������
�����������������������
����������������
������������������������
�������������������
���������������
��������
������������
���������������������������������
�������������������������������������
���������������������������
�����������������������������
����������������������������������������������������������
���������
��������
������������������������������
��� �������������������������������������������������������������������������������������������������
��� �����������������������������������������������������������������������������������������������������
��� ������������������������������������������������������������������
��������������������������������������
�����������������������������������������������������������������������������������
��� �������������������������������������������������������������������������������
��������
������������������������������������������
����������������������������������������������������������
������������
������������
����������
����������������������������������
������������������������
������
��������
������������
�������������������������������������������������
���������������������������������������������������������
���������
��������
���������
������������
������������
������������������������
���������
�����������������������
��������������
���������������������������
�������������������������
�������������������������
��������������������
����������������������������
������������������������
������������������������
������������������������������
�����
�������������������������
�������������������
������������������������
���������������������������
�������
���������
��������
5
OPERATION AND MAINTENANCE
MANUAL FOR
FINN T170 HYDROSEEDERS®
This manual gives you step-by-step instructions for the operation and maintenance of the Finn HydroSeeder®.
For best results and to insure longer life of the equipment, please follow these instructions carefully. For your
safety read the entire manual before operating this unit.
DEFINITION OF HYDROSEEDING:
Hydroseeding is the process whereby seed, fertilizer and/or lime and wood fiber mulch (using water as a carrying medium) are applied on the soil to establish vegetation.
THE FINN HYDROSEEDER® AND HOW IT WORKS:
The Finn HydroSeeder® will apply seed, fertilizer and/or lime, wood fiber mulch, or stabilizing materials in
any prescribed or desired combination. The materials placed in the HydroSeeder® slurry-tank are mixed with
water and kept in suspension by a dual agitation process, recirculation of slurry and mechanical agitation, thus
forming a slurry that is pumped to the discharge assembly and directed onto the seed bed by the operator. This
equipment is designed to accomplish hydroseeding in one easy operation with maximum efficiency.
MOUNTING THE HYDROSEEDER®:
For speed and mobility of operation, the HydroSeeder® should be mounted on a truck or trailer, however, it is
important to select a carrier with sufficient capacity to handle the added weight.
DIMENSIONS, CAPACITIES, & TRUCK REQUIREMENTS:
T170
*CF Back of cab to end of frame
C Distance from HydroSeeder® front to center of gravity
*CA Back of cab to center of rear axle or trunnion on
tandem
*FE Front axle weight – Empty
English
Truck GVW **
(Metric)
35,900 lbs. (16,284 kg)
CA **
110 in.
(279 cm+)
C (loaded)
71 in.
(180+ cm)
HW HydroSeeder® weight
C (empty)
112 in.
(284+ cm)
*RE Rear axle weight – Empty
OAL
191.5 in. (486.41+ cm)
HW (empty)
6,500 lbs. (2,948+ cm)
*FL Front axle weight – Loaded
G Distance from center of bogie to HydroSeeder® center
of gravity
*RL Rear axle weight – Loaded
*WB Truck wheel base
HW (water only)
* These dimensions needed from the truck supplier as
well as front axle capacity and rear axle capacity.
HW (full load) ***
** Truck GVW depends on the truck weight. CA dimensions are approximate only, and depend on the front and
rear axle capacities, as well as the front and rear empty axle weights.
21,200 lbs. (9,616+ kg)
23,900 lbs. (10,841+ kg)
***Weight of HydroSeeder®, water, and full charge of granular solids only. No auxiliary equipment or loads included.
6
TRUCK MOUNTING CALCULATIONS:
HW
C
G
(WB x FL) – (WB x FE) = G
HW
WB x (RE + HW -RL) = G
HW
G + C must be equal to or less than CA
(WB x FE) + (G x HW) = FL
WB
CA
FE
CF
OAL
RE
WB
FL
(WB x RE) + HW x (WB – G) = RL
WB
RL
Figure 1 - Truck Mounting Calculations & Dimensions
GENERAL MOUNTING GUIDELINES:
A BODY GUIDE OF HEAVY ANGLE, SHOULD BE BOLTED
OR WELDED TO THE HYDROSEEDER® LEG NEAR THE
FRONT END OF THE TANK. IT SHOULD EXTEND BELOW
THE LEG AND CONTACT WEAR PLATE BOLTED TO THE
FRAME SIDE RAIL. THIS GUIDE RESTRICTS LATERAL
MOVEMENT OF TANK & THUS RELIEVES SHEAR STRESS
ON MOUNTINGS.
SHIMS MAY BE REQUIRED FOR
PROPER ALIGNMENT OF GUIDE
PLATE TO WEAR PLATE.
SLOTTED ANGLE ON TOP
WITH 1/2” THICK COVER
STRAP
IMPORTANT:
INSURE THAT TUBES
ARE INSERTED TO PREVENT FULL COMPRESSION OF SPRINGS WHEN
BOLTS ARE TIGHTENED.
3/16” GAP
MOUNTING
KIT
#011562
3/8” x 6” WIDE MIN.WELD SECURELY TO
HYDROSEEDER®. BOLT
TO TRUCK CHASSIS.
FULL LENGTH SPACER THICK
ENOUGH TO COVER RIVET
HEADS; DRILL CLEARANCE
HOLES FOR RIVET HEADS
WHERE NEEDED.
2"
WARNING:
DO NOT WELD OR DRILL
TRUCK FRAME IN THIS AREA.
5/8” GRADE 8 BOLT &
NUTS. - ALL PLACES.
Figure 2 - General Truck Mounting Guidelines
7
Once the proper carrier has been selected, the HydroSeeder® must be securely mounted to it.
CAUTION:
Your FINN HydroSeeder® should be mounted by a qualified truck body
installer.
IMPORTANT:
Mounting the HydroSeeder® to the truck must allow for tire clearance as well
as frame twist. Place hard wood spacers along the length of truck rails or use
Finn Spring Mounting Kit (#011562) or equivalent.
ATTACHMENTS:
1. Extension hoses for reaching remote areas are available in 50 ft. (15m) lengths. All connections are
camlock quick operating fittings. The hose is connected to the end of the discharge boom in place of
a nozzle. The nozzle is connected to the end of the hose and controlled by the person on the ground.
The flow is controlled by a second person on the HydroSeeder®. This allows for a full pressure and
volume operation.
CAUTION:
Since the extension hose will be seeing the full output of the pump with
the recirculation closed, the equipment operator and individual at the
end of the hose should exercise extreme care when operating unit on high
pressure. The high pressure on the hose can exert strong forces causing
hose operator to lose control of hose or footing. The hose will require
additional holders on slopes. Engage the clutch only after the hose operator is firmly positioned and has firm control of hose.
2. For lower pressure applications, or for close up work, i.e. around buildings, the remote valve attachment can be used. The attachment includes semi-rigid hose with quick disconnect fittings along with a
hand held valve which fits the end of the hose and accepts the standard nozzle assemblies. The hose is
connected to the outlet on the discharge pipe above the pump. The machine is run at 1/2 to 3/4 throttle
and material is applied where desired.
DANGER:
The recirculation valve must be open when using a remote valve. If valve
is not open, extreme heat will occur resulting in damage and/or bodily
injury.
3. Hose Reel. The live hose reel will mount on the HydroSeeder® or on the truck frame. The 200 foot
capacity electric rewind reel will wind up and store empty hose. A pivoting feature provides three
locking positions, enabling curb-side, 45 degree, and rear hose discharge. It is electrically connected
to the HydroSeeder® battery. Optionally connection is also available with hydraulic power. The entire
hose reel is protected by a UV-protective canopy.
4. Hardened Pump Parts. Pump casing, impeller, and suction cover are treated with special material
designed to resist wear.
5. Rear Spray Bar. The spray bar option is not designed for slurry application but for the dispersion of
liquids for dust control, watering, feeding and washing applications. Rear spray bar is arranged so that
operation is remotely controlled from the truck cab.
8
6. Radio Remote Control. The radio remote control option provides the operator with pump on/off control, throttle control, and engine shutdown at the end of the hose. With control of the engine throttle,
the operator can precisely adjust the pump flow to whatever output the situation requires (i.e., for
close-up work around buildings). The ability to remotely shut off the pump allows the operator to
close the recirculation valve for increased performance during hose work. Carrying the remote valve
at the end of the hose becomes unnecessary.
NOTE:
For remote pump on/off control, the clutch cylinder must be connected
to an air supply.
7. Air Flush System. The air flush option uses compressed air to purge any remaining mulch slurry from
the HydroSeeder® hose, the discharge boom and the recirculation piping. To maximize performance, all
discharge plumbing should be purged after every load. The air flush system provides a quick and easy
means of purging without the need to acquire a flush tank and an additional water supply.
PRE-START CHECK:
Safety check to insure operator safety:
1. Check condition of all mounting hardware securing HydroSeeder® to truck frame.
2. Make sure bag cutter is in place and secure.
3. Inspect that all railings are in place and secure.
4. Insure that all guards are in place.
5. With the ignition switch on, verify that the amber safety light under the operator’s platform is
flashing.
EQUIPMENT CHECK:
CAUTION:
Equipment check is made with the engine off and all rotating parts
stopped.
1. See that tool kit contains all the prescribed items (see tool list on page 75).
2. Inspect the “slurry-tank” for foreign objects. See #2 and #3 in Maintenance Section of the Safety
Summary Section on page 4.
3. Check fuel level.
4. Check the hydraulic oil level (see hydraulic system for oil specifications).
5. Check engine oil level...for oil type refer to the engine manual.
6. Check fluid level in radiator.
7. Inspect air cleaner for dust and dirt, clean if necessary.
8. Secure the drain plug on the outside-bottom of the slurry-tank.
9. Check to be certain pump drain plug is in place.
9
10. Lubricate equipment - See Lube Chart on pages 26-27.
A. Each lubrication point is marked.
B. Check automatic pressure lubricator at pump. If the stem is fully extended with thumb nut all
the way up then pressure lubricator contains lubricant - if not, lubricant must be replaced by
the following procedure (See Figure 3):
THUMB NUT
a) Turn thumb nut clockwise until stem rises to maximum height.
STEM
b) Remove cap and fill cap with sodium (water soluble) base grease.
(FINN part number 000698). Do not use lithium base (chassis
lube) grease.
PRESSURE
DISK
SPRING
CAP
c) Replace cap.
d) Turn thumb nut counter-clockwise until the thumb nut is at the
top of the stem. The spring and pressure disc in the lubricator
forces the grease, under pressure, to the pump seal.
IMPORTANT:
GREASE
Figure 3
Pressure Lubricator
When the thumb nut has moved down to within 1/2” (1.25 cm) of touching
the cap, reservice the automatic lubricator.
11. Engage and disengage clutch to determine if it “snaps” in and out.
12. Check and clean nozzle of obstructions.
13. Check pump discharge and recirculation valve handles for free movement.
14. Make sure all tank vents are clean and open. Do not plug or cap.
TWO VALVE OPERATION:
This HydroSeeder® is equipped with two independently operated plug valves to control slurry
flow. One is located in the recirculation line
below the platform, and the other is located in
the discharge line above the platform. The valve
handles should be positioned as shown in Figures
4-6 for the particular application required.
DISCHARGE VALVE
(SHOWN CLOSED)
RECIRCULATION
VALVE
(SHOWN CLOSED)
10
TANK
Figure 4 - DO NOT Engage Clutch
WARNING:
Never engage the slurry pump clutch when both valve handles are
positioned as shown Figure 4. Both valves are closed and will result in
extreme heat generation that will cause damage or bodily injury if the
slurry pump is running.
1. DISCHARGE THROUGH BOOM:
Flow is through boom with no flow through closed recirculation valve (Figure 5). Flow through boom is controlled FLOW
by engaging and disengaging slurry pump clutch. Do not
use the discharge valve to control distance. Valve should be
completely open. Control the spray volume and spray dis- OPEN
tance by adjusting the engine RPM.
2. EXTENSION HOSE THROUGH BOOM:
Flow is through boom with no flow through closed recirculation valve (Figure 5). Extension hose is connected to boom
and flow is controlled by engaging and disengaging pump
clutch, or controlling the speed of the engine.
DANGER:
CLOSED
TANK
Figure 5 - Discharge Through Boom
Do not use remote valve in this application.
3. EXTENSION HOSE OR HOSE REEL THROUGH REMOTE PORT:
Flow is through recirculation with no flow through closed discharge valve (Figure 6). Flow through hose is controlled by engaging and disengaging slurry pump clutch, or by remote valve at end of hose. Open recirculation
valve allows flow back into tank when the remote valve is closed.
CLOSED
OPEN
FLOW
TANK
FLOW
Figure 6 - Discharge Through Extension Hose or Hose Reel
11
DANGER:
Recirculation valve must be open and material flowing back into tank
when using a remote valve. A closed or plugged recirculation line will
cause extreme heat resulting in damage and/or bodily injury.
STARTING PROCEDURE:
CAUTION:
See safety summary section of the manual (pages 2-4) before operating
the machine.
Before starting, open the recirculation valve, close discharge valve and recirculation valve (if applicable), disengage clutch, and place the agitator control in the neutral position.
1. Set throttle about 1/4 open.
2. Turn the key clockwise until the starter engages and the engine starts.
NOTE:
Once the keyswitch has been turned to START, if the engine does not start
within 15 seconds, all of the lights on the five gauges will illuminate. At this
point, the engine will not start until you reset the system by turning the keyswitch back to OFF and attempt to restart the engine.
3. Allow engine to warm up for 3 to 5 minutes.
NOTE:
This engine has a safety system which will shut the engine off if the engine
oil pressure drops below 7 PSI. or if the water temperature reaches 230˚
Fahrenheit (110˚ Centigrade).
AREA COVERAGE - MATERIAL CAPACITY:
To determine the coverage per load for any HydroSeeder®, three questions must be answered prior to the application. First, is the job to be done “one step” (which is when the seed, fertilizer and mulch are applied proportionally per load) or “two step” (which is when the seed and fertilizer are applied alone and then covered by
mulch as a second operation)? Second, at what rates (usually in pounds per 1,000 square feet, or pounds per
acre) are the seeding materials to be applied? Finally, what are the loading capacities of the HydroSeeder®?
Application rates vary for different geographic locations, but in general, seed is applied at 6-10 pounds per
1,000 square feet; fertilizer is applied at a rate of approximately 400 pound per acre; and fiber mulch is applied
at 1,500 to 2,000 pounds per acre. (Note: There are 43,560 square feet in an acre). Local agronomists, agricultural extension agents, or soil and water conservation officials should be contacted for more specific information
on application rates for a given area.
The following tables show loading versus coverage rates for the Finn HydroSeeder®. Table A shows rates for
“one step” applications. The coverage area is determined by the fiber mulch capacity of the HydroSeeder®, and
the rate at which it is applied. Table B shows the area coverage when seeding only, where little or no mulch is
applied. The coverage area is determined by the granular solids capacity of the HydroSeeder®, and the rate at
which the solids are applied.
12
TABLE A
Using Seed, Fertilizer and Mulch
Unit
Amount of Material in Tank (pounds(kilograms))
T170
Seed
Fertilizer
Mulch
172 (78)
200 (91)
750 (340)
Coverage Area (sq. ft.(sq. m.))
21,780 (2,023)
Above Table is based on 1,500 pounds of mulch, 400 pounds of fertilizer and 345
pounds of seed (8 pounds/1,000 sq. ft.) per acre.
Table A Example: For T170
750 pounds Mulch per Tank
750 pounds Mulch per Tank
1,500 Pounds Mulch per Acre
= 0.5 Acre per Load
400 Pounds Fertilizer per Acre x 1 Acre = 400 Pounds Fertilizer per Load
345 Pounds Seed per Acre x 0.5 Acre = 172 Pounds Fertilizer per Load
TABLE B
Seed & Fertilizer Only
Unit
Amount of Material in Tank (pounds(kilograms))
Seed
T170
1,742 (790)
Fertilizer
Total
2,000 (907) 3,742 (1,697)
Coverage Area (sq. ft.(sq. m.))
(sq. ft. (sq. m.))
Acerage (Hectare)
217,800 (20,233)
5 (2.02)
Above Table is based on rates of 8 pounds seed and 9.2 pounds fertilizer per
1,000 sq. ft.
Table B Example: For T170
3,742 Pound Tank Capacity (Solids)
8 Pounds (Seed) + 9.2 Pounds (Fertilizer) per 1,000 Sq. Ft.
8 Pounds Seed
1,000 Sq. Ft.
= 217,800 Square Feet per Load
x 217,800 Square Feet = 1,742 Pounds Seed per Tank
13
Top of
Load Hatch
1,750 Gallons
6,625 Liters
Bottom
Gallons
(Liters)
1,700 (6,435)
1,600 (6,055)
1,500 (5,675)
1,400 (5,300)
1,300 (4,925)
1,200 (4,545)
1,100 (4,165)
1,000 (3,785)
900 (3,405)
800 (3,025)
700 (2,650)
600 (2,270)
500 (1,890)
400 (1,515)
300 (1,135)
200 (755)
100 (375)
T170
in. (cm) from
top of load hatch
9.5 (24.1)
12 (30.5)
14.25 (36.2)
16.5 (42)
18.75 (47.6)
21.25 (54)
23.5 (59.7)
25.75 (65.4)
28 (71.1)
30 (76.2)
32.5 (82.5)
35.25 (89.5)
37.75 (95.9)
40.25 (102.2)
43.25 (110)
46.75 (118.7)
50.25 (127.6)
in. (cm) from
bottom
49.25 (125.1)
46.75 (118.7)
44.5 (113)
42.25 (107.3)
40 (101.6)
37.5 (95.25)
35.25 (89.5)
33 (83.8)
30.75 (78.1)
28.75 (73)
26.25 (66.7)
23.5 (59.7)
21 (53.3)
18.5 (47)
15.5 (39.4)
12 (30.5)
8.5 (21.6)
Figure 7 - Tank Capacity Chart
14
LOADING (FOR WOOD FIBER MULCH, IF LIMING SEE PAGE 21):
CAUTION:
Take care not to lose pens, lighters, etc. from shirt pockets or drop pieces
of paper or plastic bags into the tank, as these might plug the slurry system.
1. With clutch disengaged and agitator control in the neutral position, start engine and allow it to warm up
(See starting procedure page 12).
2. Start filling the unit with water. When water reaches the top of the agitator shaft, move agitator
control to full reverse position.
Fill the tank with water from any stream or pond using a fill pump. When filling from a pond
or stream be sure to use a suction strainer to filter out contaminants which could damage the
pump and unit. Other sources of water:
1. Any pressure source, eg. fire hydrant. This unit is supplied with a 6” air gap fill
port but it is necessary to consult with local authorities before using water main, in
order to abide to all local ordinances.
2. Water tanker.
3. Piping System Cleanout Procedure (Purging Line):
A. Remove discharge nozzle and gasket from discharge boom.
B. Aim discharge boom assembly into an open area away from any persons, obstructions or high
voltage power lines.
C. Open discharge valve and close recirculation valve.
D. Increase engine speed to approximately 1/2 to 3/4.
E. Engage clutch with a firm snap. Do NOT slip clutch.
F. When discharge stream is clear flush the hose on the reel (if applicable), open recirculation
valve and close discharge valve. After recirculation stream is clear disengage clutch.
G. Replace nozzle and gasket in discharge boom.
4. Continue filling tank with water.
5. Increase engine speed to full RPM. Governed speed of the engine on the Finn HydroSeeder® should
be 2,700 to 2,800 RPM under load.
6. Start loading dry material, loading the lightest material first. Agitator control should be in full reverse
for mixing.
A. Seed - Cut the seed bag and dump contents into the slurry tank. (When using inoculant, add
it in the tank along with the seed.) When using quick swelling seeds load them just prior to
application.
B. Wood Fiber Mulch - Empty the entire bag in or cut bag and drop in the sections of fiber. The
amount of mulch to be used should be loaded by the time the water level is at 3/4 full. If
agitator stalls or a high pitch squeal comes from the hydraulic system, reverse agitation to
forward for a moment to clear the obstruction, then return agitation to reverse.
CAUTION:
Hydraulic system will overheat if agitator shaft is jammed for extended
period. This will damage hydraulic oil and system components.
15
C. Fertilizer - Stand over hatch opening and drop the bag onto the bag cutter. Grasp both ends of
the bag and dump material.
D. All other additives - Consult with manufacturer for proper loading technique.
7. When all materials are loaded and in suspension, and the tank is full, move the agitator to neutral then
full speed forward to insure all material is mixed. It may be necessary to change the agitator direction
more than once to insure a thorough mixture.
8. After material is thoroughly mixed, slow agitator in forward direction to 1/2 to 3/4 speed or enough to
create movement in all of the corners of the tank. Do not over agitate the slurry. Always discharge the
material with the agitator control in forward position.
9. Close the hatch lid on the slurry tank.
NOTE:
The slurry should not be recirculated for more than 15 minutes prior to discharge to reduce wear and keep seed from swelling.
NOTE:
If foaming occurs, reduce agitator speed.
PRIOR TO APPLICATION:
1. Operator should familiarize self with area to be seeded and develop a plan to insure uniform application.
2. Develop a plan for communication between operator and driver of the carrying or towing vehicle to
signal for start, stop, turn, etc. through the use of the signal horn.
3. Operator takes up position on the platform. From this point application will be controlled by the use
of the clutch, valve, discharge assembly and throttle.
DISCHARGE NOZZLE SELECTION:
Nozzles are stored in the tool box. This HydroSeeder® is
equipped with 6 nozzles - two long distance and four ribbon
fan nozzles. The smaller long distance nozzle is generally
better suited for seed, fertilizer and/or lime application while
the large long distance nozzle is better for wood fiber mulch
application. All of the ribbon fan nozzles are generally suited
for both types of application.
Nozzle
Part Number
Distance (A)
B
A
Figure 8 - Nozzle Spray Dimensions
Width (B)
Discharge Time
Lg. Long Distance
008465
Up to 200 ft. (61m)
-
7.5 min.
Sm. Long Distance
011703
Up to 150 ft. (46m)
-
30 min.
Sm. Narrow Ribbon
011707
Up to 75 ft. (23m)
15 ft. (4.6m)
30 min.
Sm. Wide Ribbon
011706
Up to 45 ft. (14m)
25 ft. (7.6m)
30 min.
Lg. Narrow Ribbon
011891
Up to 90 ft. (28m)
23 ft. (7m)
10.6 min.
Lg. Wide Ribbon
011890
Up to 50 ft. (15m)
35 ft. (10.5m)
10.6 min.
16
APPLICATION OF SLURRY:
I. GENERAL APPLICATION TECHNIQUES
DANGER:
Do not spray toward power lines, transformers or other high voltage conductors.
CAUTION:
The driver of the carrying vehicle should remain alert for hazards to
the operator, such as low power lines, hanging branches, etc. Driver
should never start or stop abruptly.
1. Determine which nozzle would best suit the application needs according to the nozzle selection chart
on page 16.
2. Application of seed, fertilizer and lime: Elevate discharge nozzle no less than 10˚ above the area to be
sprayed, allowing the slurry to gently rain onto the seed bed.
3. Application of wood and paper fiber: Whenever possible aim the stream towards the ground to
create a surface with small pock marks which help get seed in contact with ground. Do not allow the
stream to blast away the surface of the seed bed.
4. Generally the most remote area of the seed bed should be covered first. Distance is controlled by
engine speed and nozzle selection. Do NOT partially close the valve to control the distance.
5. While moving along area to be seeded, the operator should move the nozzle back and forth in a slow,
even arc.
6. If application is to be interrupted for a short period of time, disengage the clutch. If shutdown is going
to be for an extended period of time (i.e., lunch break, reloading, etc.), close the valves to prevent slurry from dewatering. Re-engage the clutch to continue application.
7. It may be necessary to slow the agitator as the tank empties to reduce foaming.
II. DISCHARGE THROUGH THE BOOM:
1. Move the discharge valve handle to the open position, the recirculation valve handle to the closed position, and engage the clutch. At this time, should the operator want to stop spraying for a short period,
disengage the clutch; then re-engage to continue spraying.
2. When the tank is empty, or when discontinuing discharge for an extended period of time, disengage the
clutch, then immediately move the discharge valve to the closed position, and idle the engine. This will
maintain moisture in the discharge piping and help prevent plugging. Move the agitator control to the
neutral position.
III. PROCEDURES WHEN USING HOSES:
Always pump clear water through the hose before pumping mulch. If the inside hose liner is dry, it will dewater
the mulch causing plugging.
17
A. PUMP TAKE OFF SYSTEM OR HOSE REEL WITH REMOTE VALVE:
1. Open recirculation valve and close discharge valve and close remote valve at the end of the hose.
2. Engage clutch. When stream is flowing freely through the recirculation line, open the pump take off
valve.
CAUTION:
The high pressure on the hose can exert strong forces causing hose operator to lose control of hose or footing. The hose will require additional
holders on slopes. Open the pump take off valve and the remote valve
slowly and only after the hose operator is firmly positioned and has firm
control of hose.
3. With the engine at approximately 2,000 RPM, open the remote valve at the end of the hose to discharge
the load.
4. When finished spraying, close the remote valve, disengage the clutch, and stop the engine. If using
fiber mulch, retain as much water as possible in the hose by elevating the ends or by coupling the ends
together.
5. If another load is to be done, see reloading procedure on page 19. If finished for the day, follow the
clean up procedure and flush out the hose.
DANGER:
The recirculation valve must be open when using a remote valve. If not
open, extreme heat generated by dead-head pump which will cause damage and/or bodily injury will occur.
B. EXTENSION HOSE SYSTEM - WITHOUT REMOTE VALVE:
1. Connect the extension hose into the end of the discharge boom.
2. A person controlling the end of the hose directs a second operator at the machine to control the clutch
and adjust the engine speed.
CAUTION:
Since the extension hose will be seeing the full output of the pump with
the recirculation closed, the equipment operator and individual at the
end of the hose should exercise extreme care when operating unit on high
pressure. The high pressure on the hose can exert strong forces causing
hose operator to lose control of hose or footing. The hose will require
additional holders on slopes. Engage the clutch only after the hose
operator is firmly positioned and has firm control of hose.
3. When hose operator is ready, signal the second operator to engage clutch and slowly increase the
engine RPM until the desired discharge pressure is reached.
4. When finished spraying, disengage the clutch, stop the engine, and close the discharge valve. If using
fiber mulch, retain as much water as possible in the hose by elevating the ends or by coupling the ends
together.
5. If another load is to be done, see reloading procedure on page 19. If finished for the day, follow clean
up procedure and flush out the hose.
18
C. HOSE WORK WITH RADIO REMOTE:
1. Begin with the engine around 1/4 throttle (1,400 RPM).
2. Close recirculation valve. If using an extension hose connected to the discharge boom, open the discharge valve. If using the hose reel, close the discharge valve and open the pump take off valve to the
hose reel.
3. Switch Remote On/Off switch on the control panel to the "ON' position.
4. When the operator is in position, engage the pump using the remote transmitter and increase throttle to
the desired output.
IMPORTANT:
To quickly shut off the engine at any time, press the red "E-Stop" button on
the transmitter. To restart the engine, the key switch on the control panel must
be returned to the "OFF" position and then re-started.
5. When finished spraying, turn the pump off and decrease the engine throttle to idle.
CAUTION:
When using the radio remote control option, the secondary operator(s)
must be aware that the machine can be activated remotely at any time
after the Remote On/Off switch on the control panel is switched ON. If
any maintenance or troubleshooting needs to be performed while the
engine is running, the Remote On/Off switch must be in the off position.
RELOADING PROCEDURE:
1. Start at step 2 in loading procedure on page 15.
2. After last load of the day refer to the cleaning and maintenance section of the manual on pages 24-33.
3. If the unit is equipped with an Air Flush System, refer to the Air Flush System Parts & Operator's
Manual.
LIMING WITH THE HYDROSEEDER®:
In using large concentrations of granular solids through the HydroSeeder®, it is advisable to keep the slurry
moving through the pump at all times. This keeps the solids from settling in the lines, and creating a stoppage.
This unit was designed for the application of agricultural grade lime only.
PROCEDURE:
1. With clutch disengaged and agitator control in neutral position, start engine and allow it to warm up
(see starting procedure on page 12).
2. Start filling the unit with water. When water reaches the top of the agitator shaft move agitator control to approximately 1/2 speed reverse.
3. Open both the recirculation and discharge valves.
4. Remove the discharge nozzle and gasket from the discharge boom.
5. Aim the discharge boom assembly into an open area away from any persons, obstructions or high voltage power lines.
19
6. Move the throttle to approximately 1/2 engine speed.
7. Engage the clutch, and move the throttle to full engine speed. A stream of water should be coming
from the end of the recirculation pipe beside the hatch opening, as well as from the boom.
8. As soon as both streams are clear, close the discharge valve and make sure water is being
recirculated back to the tank.
9. Decrease throttle to 3/4 speed. Increase agitator speed to full reverse. DO NOT DISENGAGE
CLUTCH!
10. 20 pounds of granular solids displaces approximately 1 gallon of water. When filling the tank with
water, the volume of granular solids must be accounted for. For example; If using the T170 maximum
recommended capacity of 5,000 pounds, 250 gallons (5,000/20 = 250) would have to subtracted from
the total tank capacity (1,750 gallons - 250 gallons = 1,500 gallons). If 1,000 pounds of solids were
used, 50 gallons (1,000/20) would have to be subtracted (1,750 gallons - 50 gallons = 1,700 gallons).
11. Fill the tank to the required capacity for the rate of granular solids to be applied.
12. Load the material (see “Loading” pages 15-16, steps 5-8).
13. When ready to apply slurry, install gasket and nozzle into boom.
14. Move agitator control to 3/4 speed, forward.
15. With the clutch still engaged, open the discharge valve.
CAUTION:
To decrease pump wear and increase discharge distance, it may now be
desirable to close the recirculation valve. However, the recirculation
valve must be open BEFORE closing the discharge valve if the application of slurry is to be interrupted. Extreme heat, which will cause damage
and/or bodily injury, will occur if both valves are closed.
16. Apply the slurry (see “Application of Slurry” pages 17-19).
17. If another load is to be applied, start again at step “1”. If finished, follow the clean-up procedure.
TROUBLESHOOTING YOUR HYDROSEEDER®:
Because of the tremendous work load usually placed upon the HydroSeeder®, minor malfunctions will occur
from time to time. If these are not remedied immediately, they could lead to poor performance and damage to the
equipment. This section describes possible problems and the action to correct them.
1. Foam in the tank and air entrainment.
The mixture of dry materials with water will sometimes cause excessive foaming while others will
cause air entrainment. This is noticed primarily in the erratic discharge and a drop in pressure and distance.
Some solutions are:
A. As the slurry level drops in the tank, slow the agitator.
B. Add 2 or 3 ounces (4 to 6 cl) of an antifoaming agent to the tank.
C. If you can determine which additive is causing the air problem, either add it last or not at all.
D. Limit recirculation time as much as possible.
E. Open pump suction bleed valve to exhaust air trapped in the pump or suction line. Close valve
as soon as the air stops.
20
2. Plugging or clogging:
DANGER:
Turn off engine and disconnect battery cables before working on equipment. Serious injury or death can result from moving parts or high pressure spray.
Sometimes when a stoppage occurs, you will not be able to find anything in the line. When this happens, it means that the system became airbound instead of plugged. To remedy this, see “Foaming”.
Plugging can occur in any one of four places; the valve and recirculation nozzle, the discharge nozzle,
the pump area and the sump area. The plugging is caused by either foreign objects or dewatered
mulch.
A. Obstruction in the discharge nozzle is determined by a change or stoppage of the spray pattern.
a) Disengage clutch.
b) Make certain that the pump has stopped rotating.
c) Remove the nozzle, slowly and carefully.
d) Clear the nozzle with the nozzle cleaning rod attached to the underside of the guard rail.
DANGER:
Severe injury can result from opening clamps when piping is hot. Before
loosening any clamps, determine if the pipe is hot. If so, let it cool before
attempting repair.
B. If the recirculation system is not working:
a) Disengage the clutch and shut down the engine.
b) Remove the two clamps on each side of the recirculation valve.
c) Slide the rubber seals back and remove the valve assembly.
d) Check the valve assembly, the recirculation nozzle in the discharge pipe, and the recirculation
pipe going into the tank. Clear any obstructions.
e) Replace valve assembly and slide the seals back into place. Lubricate the outside of the seals.
f) Replace the clamps.
3. Obstruction in the pump, which can be determined by a drop in pressure. If the drop in pressure is
accompanied by a frothy or whitish discharge stream, the blockage is in the suction line or sump area.
To clear the pump:
A. Disengage the clutch and stop the engine.
B. Loosen the suction pipe clamps. If there is material in the tank, shut off the suction line valve.
C. Remove the clamp closest to the pump.
NOTE:
If no water comes out, it means that the obstruction is in the sump area.
E. Reach into the pump and remove the obstruction. If it is jammed, the pump suction cover may
have to be removed.
F. Reassemble removing pipe “plug” in process.
G. Open suction line valve.
21
4. Obstruction in the sump area, which is located at the bottom of the tank on the inside where the suction pipe is attached:
A. The easiest way to clear the sump is to back flush through the discharge plumbing with the
water supply hose.
B. Another method is to remove the drain plug and run a long pole through the opening and into
the sump area. Remove the obstruction and replace the drain cap.
C. Use a pipe or pole through the loading hatch opening to dislodge the obstruction.
TROUBLESHOOTING YOUR HYDROSEEDER®:
Problem
Probable Causes
Suggested Solutions
Tank Bearing
Lack of lubrication - seal worn
Bolts not tightened properly
Replace seal and follow lube schedule
Tighten uniformly to 25 ft. lbs.
Pressure Pipe Clamps
Rubber seal cracked, pinched
or torn
Replace, always grease seal before
clamping shut
Suction Pipe Clamps
Rubber seal cracked, pinched
or torn
Replace, always grease seal before
clamping shut
Discharge Swivels
Not greased often enough
Rebuild swivels w/repair kit (part
#012397, quantity 2 required)
Pump Shaft
Pressure lubricator not serviced
Replace pump seal, service pressure
lubricator daily
Pump Suction Cover
Cover O-Ring bad
Replace cover O-Ring, use grease
when replacing
Discharge Boom or
Nozzle Camlock Fittings
Worn or no gasket
Replace gasket
LEAKS:
MACHINE JUMPS DURING OPERATION:
Agitator
Agitator bent by heavy object
falling on it
Straighten agitator or shim, so it runs
true
Bent Paddles
Loading wood fiber mulch into
tank before tank is half full
Straighten agitator paddle, realign
agitator to run true
FOAMING OF SOLUTION AND LACK OF DISTANCE:
Pump loses prime - lacks
distance - leaves excessive
amount in tank (100 gal
(378 liters) or more)
22
Sucking air in suction lines
Check all suction connections to see
that rubber seals are in good shape.
Grease seals before replacing clamps.
Air entrainment
See page 20
Low engine RPM (Below
Check throttle cable and linkage,
2,750 RPM-No load)
See authorized engine dealer
Soft water
Slow the agitator
TROUBLESHOOTING YOUR HYDROSEEDER®:
Problem
Probable Causes
Suggested Solutions
Pump loses prime - lacks
Too much agitation
Slow the agitator
distance - leaves excessive
Pump worn
Reset pump tolerance page 30
amount in tank (100 gal
Suction partially plugged
Clean out machine see pages 24-25
(378 liters) or more)
Nozzle worn or plugged
Clean nozzles, replace if necessary
Fertilizer
Change type
Clutch slippage
Readjust clutch - see clutch manual
Valve stuck
Frozen
Thaw out ice & lubricate - leave in
discharge position during storage
Constant plugging during
operation
Foreign material in slurry
Drain and clean out tank - check
storage for foreign materials
Constant plugging during
Loading HydroSeeder® before
Reinstruct your operator - see
loading and discharging
tank is half full of water
pages 15-16
Incorrect loading procedure
See loading procedure pages 15-16
Improper operation by operator
Reinstruct your operator Review Operator’s Manual)
Clutch slipping
Readjust clutch - see manual
Not moving valve handle
far enough
Valve should be fully open
Machine not being flushed out
prior to reloading
See page 15
Machine not being run at
correct RPM during loading
Reinstruct your operator - see
page 15
Letting water run out, leaving
wood fiber mulch to dry out
If hose has to be uncoupled, seal ends
to keep water in hose and prevent
wood fiber mulch from drying out
Does not pull load or overheats
Out of adjustment
Readjust clutch, instructions in
clutch manual
Jumps out of engagement
Too loose or too tight
Readjust clutch - see manual
Fertilizer with highly abrasive fillers
Change fertilizer - avoid abrasive
fillers
Overloading machine with dry
material
Load machine to recommended
capacities
Too much time allowed between
loading and discharging
After loading and mixing has been
completed, set agitator at 1/2 speed
in reverse and disengage pump
Recirculating all the time
Close recirculation valve when
discharging through the boom
VALVE:
Extension hose plugs after use
CLUTCH:
PUMP:
Excessive wear
23
TROUBLESHOOTING YOUR HYDROSEEDER®:
Problem
Probable Causes
Suggested Solutions
Frozen
Warm housing to melt ice
Jammed with fertilizer or lime
Remove cover and clean interior
Impeller rusted to suction cover plate
Pull cover and remove rust
PUMP CONT'D:
Will not turn
CAUTION:
Do not turn the shaft backwards with a pipe wrench - this will unscrew
the impeller from the shaft. Consequently, when clutch is engaged, the
impeller will screw onto the shaft with such force, great enough to break
the impeller.
CLEANING AND MAINTENANCE:
AFTER FIRST 4 - 8 HOURS OF OPERATION:
1. Check and adjust clutch - see clutch manual.
DAILY:
1. Cleaning the HydroSeeder®
A. Fill the slurry tank to the center of the agitator shaft.
B. Move agitator lever to full speed to flush off inside of tank top and walls.
C. Remove discharge nozzle and gasket from discharge boom.
D. While pointing discharge toward an open area, move discharge valve handle to discharge position and engage clutch. Allow to discharge until clear water is coming out.
E. Move recirculation valve handle to recirculation and allow to run momentarily.
F. Disengage clutch, idle the engine, move valve handle to discharge position, move agitator handle to neutral and turn off the engine.
G. Always remove the drain plug and allow the tank to drain.
H. In freezing weather leave main tank drain plug out and remove pump drain plug. Move all
slurry valves to open position.
I.
Wash the outside of the HydroSeeder ® , including the radiator, to remove any corrosive
materials.
J. If using lime - the daily maintenance should be performed after every load.
K. Clean out extension hoses.
L. Make sure all tank vents are clean and open. Do not plug or cap.
2. Lubricating the HydroSeeder® (See lube chart pages 26-27)
IMPORTANT:
24
Lubrication should be performed IMMEDIATELY AFTER cleaning of equipment. Engine not running.
A. Lubricate the agitator shaft bearings located on the outside front and rear of the slurry-tank.
B. Service the automatic lubricator on the pump as needed (for service see page 10).
C. Check the engine oil and replenish when necessary. Change oil and filter after first 100 hours
then 250 hours thereafter. Consult the engine operator’s manual for the correct grade of oil
and the engine break-in procedure.
D. Lubricate the swivel on the discharge assembly and the swivel on the hose reel.
E. If equipped with the Air Flush Option, refer to the Air Flush System Manual.
WEEKLY OR EVERY 40 HOURS OF OPERATING TIME:
1. Clean the air cleaner following the instructions in the engine operator’s manual.
2. Lubricate all the points on the HydroSeeder® as outlined in the daily maintenance section and, in addition, lubricate the four grease fittings on the clutch/pump.
3. Check the level in the hydraulic oil reservoir - maintain level at sight gauge.
4. Check the clutch adjustment to insure that it “snaps” in and out of engagement. Adjust the clutch with
the engine off.
5. Check the anti-freeze in the radiator.
6. Inspect the slurry-tank for build up of residue in the suction area and clear if necessary.
7. Check and clean engine radiator. Flush with clear low pressure water and blow dry with compressed
air. Do NOT use high pressure water spray.
8. Check pivoting hose reel swivel bolt. Ensure proper torque. Replace bolts if any show signs of wear.
SEASONAL AND WINTER STORAGE MAINTENANCE:
1. Drain the slurry-tank of all water prior to storage and leave the drain plug disconnected.
2. If possible, cover machine with tarp or park inside of an enclosure.
3. Store the HydroSeeder® with all slurry valve handles in the open position. To prevent damage from
freezing, it is advisable to remove all slurry valves and store in a heated area.
4. Pour one quart of mineral oil or environmentally safe lubricant into the pump housing and spin pump
by hand to prevent rust in the pump. Remove drain plug.
5. Chip and steel brush any interior rust spots in the slurry-tank and touch up with paint. See #2 and #3
in Maintenance Section of the Safety Summary Section on page 4.
6. Lubricate all fittings.
7. Check anti-freeze in radiator.
8. Lubricate equipment again just prior to starting operation after storage.
10. Change hydraulic oil and filter. (500 hours)
11. Disconnect battery cables. In cold weather, remove battery and store in safe warm place.
12. Add fuel stabilizer to fuel tank.
HYDRAULIC SYSTEM:
The hydraulic system on your Finn HydroSeeder® is designed to give trouble free service, if maintained. The
most important areas of maintenance are the hydraulic oil and filtration. The reservoir holds 22 gallons of Mobil
DTE-13M or equivalent hydraulic oil. The hydraulic oil should be replaced per the lubrication schedule or if the
oil becomes milky or it gives off a burnt odor. The hydraulic oil filter must be replaced on schedule with a 25
micron absolute filter – Finn part #021618. The hydraulic system relief is factory set at 2,800 PSI.
25
3
3
4
9
3
2
7
9
8
11
12
10
6
26
1
5
LUBRICATION CHART
Ref. No.
1
2
3
4
5
6
7
8
9
10
11
12
Location
Lubricant
Frequency
BL
CL
CL
DF
CL
MO
MO
BL
HO
HO
SL
CL
AF
Daily
Weekly
Daily
Daily
Daily
Daily
See Engine Manual
Weekly
Weekly
Seasonally or 500 Hours
Each Load
Weekly
Seasonally
Check Grease Level in Pressure Lubricator
Check Clutch Lever Bearings
Grease Agitator Shaft Bearings
Check Fuel Level
Grease Discharge Swivels
Check Engine Oil Level
Check Engine Oil and Filter
Grease Pump Bearings
Check Hydraulic Fluid Level
Change Hydraulic Fluid and Filter
Grease Discharge and Recirculation Valves
Grease Valve Arm Lever
Change Engine Coolant
Number
1
2
2
1
2
1
1
2
1
1
2
1
1
LUBRICANT OR FLUID USED
BL
CL
MO
HO
SL
AF
DF
Bearing Lube (Soda Based)
Chassis Lubricant
See Engine Manual
Mobil DTE-13M or Equivalent Hydraulic Oil
Special Stick Lubricant
50/50 Anti-Freeze and Water Mixture
Diesel Fuel
TIME KEY
DAILY (8 hours)
WEEKLY (40 hours)
EACH LOAD
SEASONALLY (500 hours)
SEE ENGINE MANUAL
FLUID CAPACITIES
Fuel - 38 Gallons (143.8 L)
Hydraulic Oil - 22 Gallons (83 L)
Engine Coolant - 4-1/4 Gallons (16 L) 50/50 Mix Only
Engine Oil - See Engine Manual
27
8
16
7
6
17
23
21
22
20
14
15
13 12
11
10
5
1
19
24
18
30
25
26
29
27
4
32
36
31
37
38
39
28
33
34
2
40
35
Figure 9 - Clump Parts
28
9
3
CLUMP PARTS
Ref. No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Part Number
Description
005146
X0824SS
0Y08SS
005150
X0824SS
WF08SS
005145
005144
006443
006444
005446
012733
012734
005544-02
007705
005570
012729
100031
100019
100018
100026
100308
100307
022314
100011
100341
100003
100028
100013
100032
100040
100323
012695
012732
012731
X0516SS
X0724SS
WL07SS
X0820SS
160234
Suction Cover
Suction Cover Bolt
Suction Cover Nut
O-Ring
Suction Cover Bolt
Suction Cover Washer
Impeller
Clump Casing
Mechanical Shaft Seal
Grease Retainer
Flange Pilot Bearing
Grease Retainer
Bearing Retainer Ring
Sealing Gasket
Grease Fitting
Instruction Plate
Clump Shaft
Release Bearing
Connecting Link
Release Lever
Lever Spring
Lock Washer
Drive Shaft Nut
Pilot Bearing
Clutch Body
Clutch Facing
Driving Ring
Pressure Plate
Adjusting Ring
Adjusting Ring Plate
Cross Shaft
Clutch Yoke
Clump Housing
SN-11 Nut
Bearing
Thrust Bearing Retainer Bolt
Flange Bearing Bolt
Flange Bearing Lock Washer
Bolt
Pipe Plug
No. Req’d
1
4
4
1
8
8
1
1
1
1
1
1
1
1
2
1
1
1
6
6
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
6
4
4
3
2
29
CLUMP MAINTENANCE SECTION:
CAUTION:
Clump maintenance to be done only while engine is not running, and battery cables are disconnected.
A. FACTORY-TOLERANCES
1. To check clump tolerances loosen the two clamps on the pump suction piping and remove the inlet
elbow. Through the pump suction hole, insert a feeler gauge between the impeller (7) and the suction
cover (1). This measurement on a new clump is between .040-.045"(1.00-1.15 mm).
B. IMPELLER CLEARANCE
TO BRING THE CLUMP BACK TO PROPER TOLERANCE, PROCEED AS FOLLOWS:
1. Push suction cover (1) into casing (8) until suction cover hits impeller (7). Impeller should be in full
contact with suction cover (1).
2. Tighten bolts (5) finger tight. Impeller (7) should rub the suction cover (1) and not turn easily through
one revolution.
3. Tighten bolts (2) to 15 lb. ft. (165 kg/m). Impeller (7) should turn freely through one revolution.
4. Back off bolts (5) 3/4 turn.
5. Tighten bolts (2) 3/4 turn and tighten nuts (3) to 15 lb.ft. (165 kg/m).
6. Tighten cap screws (5) to 15 lb. ft. Clearance gap should be about .040" (1.00 mm).Check to see if
impeller (7) turns freely through one revolution.
NOTE:
Tightening of the bolts (7) should be in a criss-cross pattern. DO NOT
TIGHTEN TO OVER 15 LB. FT. (165 kg/m). Doing so can crack the flange
of the suction cover (1).
C. CLEANING
1. To clean impeller (7), loosen the two vitaulic pipe clamps and remove the suction pipe assembly. The
eye of the impeller (7) can then be seen through the suction cover plate (1) and is readily accessible for
cleaning.
2. To remove impeller (7), remove the eight bolts (5) holding the cover (1) in place. Remove suction
cover (1), being careful not to damage the O-Ring (4).
3. Take the impeller wrench, which is stored in the toolbox, and position it so that the hole is aligned
with any of the eight tapped holes in the front of the pump casing (8). The 90° leg of the wrench
should face in towards the impeller and be positioned between any two of the impeller fins. Bolt the
wrench securely in place with one of the suction cover bolts (5). Using a pipe wrench on the shaft
(17), unscrew the impeller (7) turning the shaft in a clockwise direction. Be careful not to unscrew the
impeller too far before removing the puller wrench.
30
D. INSTALLING NEW SEAL ASSEMBLY
(DO NOT UNWRAP THE NEW SEAL ASSEMBLY UNTIL YOU ARE READY TO INSTALL. ALL PARTS OF
THE ASSEMBLY ARE PACKED IN SEQUENCE OF INSTALLATION.)
1. To replace the seal assembly (9), perform the above operations under cleaning and remove pump casing
(8) by removing the three bolts (39) holding the clump casing (8) to the clutch body (33).
2. After cleaning all parts including pump shaft, begin the reassembly of the clump. Install seal grease
retainer (10) with the cavity portion of the seal facing outward. Rebolt the casing onto the pump frame
using the three bolts (39). Using a light oil lubricant (3 in 1), install the ceramic seat with its neoprene
holder into the seal recess making sure it is square with the shaft. Lubricate the inside of the bellows
assembly with a light oil and check to be sure the steel ring is stuck (glued) to the end of the assembly.
Slide the bellows assembly onto the shaft and push till the steel ring is against the ceramic seat.
3. Install the seal spring on the hub of the impeller. After coating the threads on the clump shaft (18) with
an anti-seize compound, install the impeller (7) - seating it securely.
4. Utilizing the rubber O-Ring (4) reinstall suction cover (1) using the eight cover bolts (5). At this time,
check to see that the clump runs freely. If the impeller (7) rubs the cover plate (1), you do not have the
impeller (7) tight on the shaft (17) or the suction cover (1) needs readjustment - see “impeller clearance”. Tighten these bolts (5) uniformly using 15 ft. pounds (165 kg/m) on the torque wrench.
5. After reinstalling the suction pipe assembly, lubricate and tighten the victaulic clamps. Service the
automatic lubricator.
31
5
40 Pressure Lubricator
(Includes Items #41-43)
41
4
41
3
41
2
1
42
43
13
14
12
15
11
10
16
9
17
8
18
7
6
NOTE:
39
35
38
Item #19 (10¨ Clutch
Assembly Kit) Includes
Items #20-36)
34
37
28
33
27
31
26
23
30
36
29
34
32
25
Figure 17 - Clump Assembly
32
24
22
21
20
CLUMP ASSEMBLY
Ref. No.
Part Number
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
005146
005150
005145
006443
005144
006444
005446
012733
012734
012729
012731
012732
100063
012695
100323
100042
100040
005574-02
012783
100321
100030
100031
100332
100224
100029
100026
100032
100013
100028
100341
100003
100011
100008
100019
100018
100009
100308
100307
022314
002383
008190
007954
008189
Suction Cover
O-Ring
Impeller
Mechanical Shaft Seal
Clump Casing
Grease Retainer
Flange Pilot Bearing
Seal
Bearing Retainer Ring
Clump Shaft
Bearing
SN-11 Nut
Instruction Plate
Clump Housing
Clutch Yoke
Woodruff Key
Yoke Shaft
Modified Clutch Lever
10" Clutch Asembly Kit
External Snap Ring
Bearing Carrier
Release Bearing
Internal Snap Ring
Lube Fitting
Release
Lever Spring
Adjusting Ring Plate
Adjusting Ring
Pressure Plate
10" Clutch Disc
Driving Ring
Clutch Body
Retaining Ring
Connecting Link
Release Lever
Clevis Pin
Lock Washer
Drive Shaft Nut
Pilot Bearing
Pressure Lubricator
Screw, Nut, Follower & Spring
Spring
Plunger
No. Req’d
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
6
6
6
6
1
1
1
1
1
1
1
33
NOTES
34
NOTES
35
NOTES
36
NOTES
37
NOTES
38
T170
®
HydroSeeder
Parts Manual
Model SL
LBT70-SL
39
NOTES
40
PICTORIAL REFERENCE
STRUCTURE & RAILING
CONTROLS
(Pages 42-43)
(Pages 60-61)
HATCH ASSEMBLY
CONTROL BOX WIRING
(Pages 44-45)
(Pages 62-63)
CLUMP, PIPING
& DISCHARGE ASSEMBLY
(Pages 56-57)
CLUMP ASSEMBLY
(Pages 58-59)
DISCHARGE BOOM ASSY
(Pages 46-47)
AGITATOR & SEAL ASSY
ENGINE & RADIATOR
HYDRAULIC SYSTEM
ENGINE SHEET METAL
HYDRAULIC AGITATOR DRIVE
AIR INTAKE & EXHAUST SYSTEM
(Pages 64-65)
(Pages 66-67)
(Page 68)
(Pages 48-49)
HOSE REEL ASSEMBLY
(Pages 70-71)
(Pages 50-51)
(Pages 52-53)
ELECTRICAL SYSTEM
(Pages 54-55)
DISCHARGE HOSE EXTENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 69
DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pages 72-73
RECOMMENDED SPARE PARTS & REPAIR KITS . . . . . . . . . . . . . . . . . . . . . . . . Page 74
TOOL KIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 75
41
41
40
42
39
43
8
29
38
37
9
11
10
6
SEE FUEL TANK
DETAIL
(On Page 43)
7
12
5
13
4
3
14
2
1
7
23
36
35
34
9
33
8
32
15
16
31
24
28
27
26
25
17
22
18
19
20
29
30
42
21
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
21
FUEL TANK DETAIL
44
45
STRUCTURE & RAILING
Ref. No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
Part Number
012700
012755
008582-01
F170-0015
008639
008582-02
012703
012737
F280-0005
F170-0013
190047
F330-0082
012705
012708
012702
F330-0086
012669
F330-0078
085152
005619
012514
005613
F330-0075
002290
012736
F330-0084
F330-0081
F170-0029
002191
002190
190018
060316
012701
F330-0089
012771
012707
012750
008470
005700
012515
012749
FW71225
005700
012693
012694
Description
Swing Gate
Spring Hinge
Front Tank Top Support
Left Rear Toe Rail
Left Rear Guard Rail
Rear Tank Top Support
Slide Gate
Front Side Guard Rail
Front Side Toe Rail
Tank Top
Foam Gasket
Front Toe Rail
Front Guard Rail
Hatch Safety Guard Rail
Right Rear Guard Rail
Right Rear Toe Rail
Toolbox
Tool Box Mount
Rubber Stud Mount
U-Bolt For 1-1/4" Round Pipe
Square U-Bolt For 1-1/2" Square Pipe
Square Tubing Plug
Nozzle Holder
Rear Marker Light - Red
Rear Corner Guard Rail
Rear Corner Toe Rail
Boom Holddown
Control Box Mount
2-1/2" Male Brass Adapter
Dust Cap w/Gasket - Main Tank Drain
2" Wide Conformable Safety Walk
3 Marker Light
Long Rear Guard Rail
Long Rear Toe Rail
Ladder Hand Rail
Short Rear Guard Rail
Fill Stack Extension
Fill Port Plug
Nylon Lanyard
1-1/4" Pipe Plug
Fill Port
Slide Gate Snapper Pin
Nylon Lanyard
Poly Fuel Tank
Fuel Gauge
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
No. Req’d
1
1
1
1
1
1
2
2
2
1
33'
1
1
2
1
1
1
1
2
2
6
10
1
2
1
1
1
1
2
1
A/R (Ft.)
1
1
1
2
1
1
1
1
1
1
2
2
1
1
43
2
3
1
4
3
2
8
5
9
9
10
8
6
11
6
7
7
13
13
12
14
12
12
13
5
15
44
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
14
12
13
HATCH ASSEMBLY
Ref. No.
Part Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
012711
070627
085152
002909
005433
005487-04
005487-03
012714-04
012714-03
012751
X0848SS
W08FSS
Y08LSS
012605
012709
Description
Hatch Lid
Hatch Lid Hinge
Rubber Stud Mount
Hatch Handle
Soft Latch
Side Hatch Lid Gasket
Side Gasket Strip Retainer Strap
Front/Back Hatch Lid Gasket
Front/Back Gasket Retainer Strap
Bag Cutter
1/2-13 UNC x 3" Lg. Hex Head Cap Screw - SS
1/2" Flat Washer - SS
1/2-13 UNC Lock Nut - SS
1/2" SS Sealing Washer
Hatch Liner
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
No. Req’d
1
2
2
1
2
2
2
2
2
1
2
4
4
2
1
45
3
4
5
2
9
7
8
3
6
NOTE:
ITEM #1 (DISCHARGE BOOM ASSEMBLY)
INCLUDES ITEMS #2 - #7.
46
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
DISCHARGE BOOM ASSEMBLY
Ref. No.
1
Part Number
012764
Description
Discharge Boom Assembly
No. Req’d
1
2
012763
Lower Boom Discharge Weldment
1
3
012283
2-1/2" Straight Swivel
2
4
012762
Upper Boom Discharge Weldment
1
5
012756
Boom Discharge Handle
1
6
012726-01
Boom Stand Pipe
1
7
010544
2-1/2" Female Coupler
1
8
9
006513
011914
2-1/2" Coupler Gasket
Black Hand Knob
1
1
NOT ILLUSTRATED
012397
Swivel Repair Kit
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
A/R
47
1
SEE VIEW A
(On Page 49)
2
3
8
4
9
7
6
5
10
11
12
15
16
9 (REF)
12
14
48
13
14
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
19
18
VIEW A
17
20
21
22
ENGINE & RADIATOR
Ref. No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Part Number
Description
075200
KU1G521-97010
075565
075563
075562
023807
F816-0008-01
F330-0096
F170-0042
F170-0014
075227
022450
075228
008641
008676
023438
KU16631-43560
075202
023814
075292-05
075284-01
008640
KU16010-32430
080105
Kubota V3300 Diesel Engine
Fan Belt
1/2" Fan Spacer
Pusher Fan
Radiator
Radiator Cap
Fan Guard
Fan Guard Mounting Strap
Top Radiator Mount
Radiator Fan Shroud
Upper Radiator Hose
2-1/2" Hose Clamp
Lower Radiator Hose
Isolator Mount
Radiator Mount
Rubber Shock Mount
Fuel Filter
Electric Fuel Pump
Electric Throttle Actuator
Actuator Mount
Throttle Pivot
Hydraulic Pump
Oil Filter
Pre-Fuel Filter
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
No. Req’d
1
1
1
1
1
1
1
1
1
1
1
4
1
2
1
1
1
1
1
1
1
1
1
1
49
1
16
2
3
4
15
14
13
5
6
12
10
10
8
11
9
7
50
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
ENGINE SHEET METAL
Ref. No.
Part Number
Description
No. Req’d
1
055669
Lock Positioning Hinge
1
2
F260-0006-02
Radiator Cap Cover
1
3
F260-0006-03
Hinge Spacer
1
4
F170-0023
Radiator Shroud
1
5
075562-01
Radiator Screen
1
6
F170-0026
Front Sheet Metal Mount
2
7
F170-0020
Radiator Pan
1
8
F170-0018
Left Front Engine Foot
1
9
F170-0019
Right Front Engine Foot
1
10
052397
Rear Engine Mount
2
11
007433
Rubber Shock Mount
6
12
007887
Snubbing Washer
6
13
F170-0025
Rear Sheet Metal Mount
2
14
F170-0035
Engine Side Panel
1
15
008663
Rear Engine Panel Weldment
1
16
F916-0033
Engine Top Cover
1
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
51
5
9
4
10
6
3
2
11
7
10
8
12
13
14
13
16
NOTES:
15
● Air Intake Assembly Includes
Items #1-16.
● Item #1 (Air Cleaner Assembly)
Includes Items #2-8.
● Exhaust Assembly Includes
Items #17-21.
10
17
18
19
18
20
18
21
52
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
AIR INTAKE & EXHAUST SYSTEM
Ref. No.
Part Number
Description
No. Req’d
AIR INTAKE ASSEMBLY
1
2
012646
012621
Air Cleaner Assembly
Air Cleaner
1
1
3
012623
Safety Filter Element (3.75-E2)
1 per
4
012622
Main Filter Element (3.75-E1)
1 per
5
012621D
Filter Cap
1 per
6
012621A
Flapper Valve
1 per
7
012621C
Mounting Bracket
1 per
8
012621B
Dust Load Indicator Gauge
1 per
9
012608
Pre-Cleaner
1
10
022657
4" Clamp
9
11
012609
Pre-Cleaner Adapter
1
12
008618
Hump Adapter
1
13
007391
3" Clamp
2
14
008652
Air Cleaner Tube Weldment
1
15
008617
Hump Adapter
1
16
008666
Cobra Elbow
1
EXHAUST ASSEMBLY
17
008648
Exhaust Extension
1
18
000461
2" Muffler Clamp
3
19
008653
Silencer
1
20
008674
Muffler Support
1
21
008684
Tailpipe
1
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
53
5
13
WHITE/
WHITE
6
14
WHITE
7
15
RED
8
16
YELLOW
BLACK
(12)
12
4
BROWN BLACK ORANGE
BLACK
(12)
BLUE
GREEN
11
3
OPEN
BLUE
10
2
RED
9
1
YELLOW RED
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
AMBER
LIGHT
BLK (5)
FLASHER
BLK (5)
WHT (13)
BLK (12)
RED (16)
YEL (16)
BRN (6)
BLK (7)
YEL (2)
BLU (10)
ORG (4)
GRN (11)
WHT (14)
BLU (8)
RED (1)
RED (9)
3)
T (1
WH
WHT (12)
WHT
WHT
85
86
87
30
B
A
THROTTLE
PRESSURE
SENDER
RED
HOSE REEL
LEAD
HORN
RELAY
BLU
85
87
86
BLU
BLU
BLU
GRN
30
BLU
STARTER
50 30
RED
AUX
RELAY
TEMP
SENDER
TACH
SENDER
54
RED
(─)
12V BATTERY
(+)
PULL
SOLENOID
HOLD
WHT
FUEL
PUMP
GLOW
PLUGS
ELECTRICAL SYSTEM
Part Number
Description
No. Req’d
FW75307
12 VDC/75 AMP SPST Power Relay
2
007336
Amber Warning Light
1
021198
Flasher
1
006499
Horn
1
011851
12 Volt Battery
1
011770
Battery Box
1
080096
Positive Battery Cable (2 Ga. x 62" Lg - Red)
1
000241
Ground Strap
1
075202
Electric Fuel Pump
1
023814
Electric Throttle Actuator
1
FW71680
Electrical Housing
1
FW71357
Female Insert - 16 Pin
1
075310
Temperature Sender
1
075308
Pressure Sender
1
075329
Tach Sensor
1
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
55
38
16
37
17
31
33
39
32
30
25
24
34
35
36
22
23
23
22
20
16
1
26
21
23
2
3
27
28
29
22
1
19
2
17
18
4
5
17
6
16
REF:
CLUMP ASSY
15
(See Pages 58-59)
9
14
10
1
11
2
5
13
12
56
8
7
4
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
CLUMP, PIPING & DISCHARGE ASSEMBLY
Ref. No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
Part Number
011736
011919
008259
0X1232
012722
012058
012491
012491-02
012457
160428
160006
008471
008472
008469
008645
002771
002820
008647
160263
008646
011727-09
006721
006722
011727-10
011776
012786
004962
011950
011951
011727-11
012726-03
012462-05
005703-02
011777
011953
008487
004962
012758
011882
Description
5" Vitaulic Pipe Clamp
Seal For 5" Vitaulic Pipe Clamp
5" Dia x 90º Pipe Elbow
3/4-10 x 2" Lg. Hex Hd. Cap Screw (Grade 5/Zinc)
Suction Valve Flange Weldment
5" Flanged Suction Gate Valve
Suction Valve Bleeder Valve Assembly
Suction Elbow Weldment
1/2" Dia. Stainless Steel Ball Valve
1/2" Dia. x 4" Lg. SCH 40 Nipple
1/2" Dia. x 90º Elbow
5" x 4" Reducing Pipe Clamp
Seal For Reducing Pipe Clamp
Pump Discharge Gasket
Pump Flange Weldment
2-1/2" Vitaulic Pipe Clamp
Seal For 2-1/2" Vitaulic Pipe Clamp
Lower Discharge Pipe Weldment
1-1/2" Dia. Pipe Cap
Discharge Valve Stand Pipe
Recirculation Nozzle
1-1/4" Vitaulic Pipe Clamp
Seal For 1-1/4" Vitaulic Pipe Clamp
Recirculation Nozzle
1-1/4" Round Port 2-Way Valve
Recirculation Lever
Lube Screw
Gasket For 1-1/4" Valve
Spring For 1-1/4" Valve
Recirculation Nozzle
Recirculation Pipe
1/2 of Guardian Coupling
1-1/4" Coupling Deflector
2-1/2" Round Port 2-Way Valve
Spring
Gasket
Lube Screw
Valve Foot Pedal
2-1/2" SCH 40 x 3" Toe-Goe Pipe
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
No. Req’d
3
1 Per
1
16
2
1
1
1 Per
1 Per
1 Per
1 Per
1
1
1
1
3
1 Per
1
1
1
1
3
1 Per
1
1
1 Per
1 Per
1 Per
1 Per
1
1
1
1
1
1
1
1
1
1
57
5
40 Pressure Lubricator
(Includes Items #41-43)
41
4
41
3
41
2
1
42
43
13
14
12
15
11
10
16
9
17
8
18
7
6
NOTE:
39
35
38
Item #19 (10¨ Clutch
Assembly Kit) Includes
Items #20-36)
34
37
28
33
27
31
26
23
30
36
29
34
32
58
22
25
24
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
21
20
CLUMP ASSEMBLY
Ref. No.
Part Number
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
005146
005150
005145
006443
005144
006444
005446
012733
012734
012729
012731
012732
100063
012695
100323
100042
100040
005574-02
012783
100321
100030
100031
100332
100224
100029
100026
100032
100013
100028
100341
100003
100011
100008
100019
100018
100009
100308
100307
022314
002383
008190
007954
008189
Suction Cover
O-Ring
Impeller
Mechanical Shaft Seal
Clump Casing
Grease Retainer
Flange Pilot Bearing
Seal
Bearing Retainer Ring
Clump Shaft
Bearing
SN-11 Nut
Instruction Plate
Clump Housing
Clutch Yoke
Woodruff Key
Yoke Shaft
Modified Clutch Lever
10" Clutch Asembly Kit
External Snap Ring
Bearing Carrier
Release Bearing
Internal Snap Ring
Lube Fitting
Release
Lever Spring
Adjusting Ring Plate
Adjusting Ring
Pressure Plate
10" Clutch Disc
Driving Ring
Clutch Body
Retaining Ring
Connecting Link
Release Lever
Clevis Pin
Lock Washer
Drive Shaft Nut
Pilot Bearing
Pressure Lubricator
Screw, Nut, Follower & Spring
Spring
Plunger
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
No. Req’d
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
6
6
6
6
1
1
1
1
1
1
1
59
21
22
23
19
20
18
DETAIL A
4
17
5
6
13
7
2
1
16
3
15
12
10
8
13
9
24
11
14
NOTE:
10
60
NOTE:
ITEM #9 ALSO
INCLUDES ITEMS #10.
ITEM #13 ALSO
INCLUDES ITEMS #14.
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
CONTROLS
Ref. No.
Part Number
Description
1
008672
Agitator Control Handle
1
2
008673
Agitator Handle Pivot
1
3
022202
Black Handle Grip
1
4
008650
Control Box Assembly
1
Control Box Decal
1 Per
5
008656
No. Req’d
6
004996
1" Pipe Plug
1
7
012777
Recirculation Handle
1
8
F330-0102
Agitator Control Box
1
9
012780-05
Recirculation Valve Rod Assembly
1
10
006737
11
012493-01
Bleeder Valve Handle
1
12
012493-09
Handle Bearing Pad
1
13
012780-08
Clutch Rod Assembly
1
14
006737
Ball Joint
Ball Joint
2 Per
2 Per
15
000427
Black Handle Grip
1
16
012760
Clutch Handle
1
17
F170-0029
Control Box Mount
1
18
085148
U-Bolt
1
19
031245
Snapper Pin
1
20
F330-0081
Boom Holddown
1
21
006596
Agitator Control Cable (74" Lg.)
1
22
004983
Clamp and Shim
1
23
007675
Ball Joint
2
24
007913
Rubber Strap w/S-Hooks
1
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
61
RED
17
19
YEL 42
30
50
BLU
AC
HORN BUTTON
3
GRN 3
RED 5
EE
E
RED
BLK 40
BLU
WHT 9
HOUR
“─”
ORG
“+”
PRESS
ORG
7
15
8
16
YELLOW/ ORANGE/
RED
RED
BROWN
BLUE/
RED
YEL
VOLT
ORG
BLK
YEL
TEMP
RED 20
BLK
BLU
BLK
EE
WHT 10
WHT 37
TACH
GRY
EE
EE BRN 26
BLK
BLK
YEL 30
WHT 8
13
14
12
4
11
3
BLACK BLACK/ ORANGE/ BROWN/
RED
BLACK
RED
5
6
9
RED/
BLACK
10
BLUE
1
2
YELLOW/
BROWN/ BLUE/
BLACK BLACK ORANGE BLACK YELLOW RED
RED 36
SHUTOFF BUTTON
BRN
BLU 8
BRN
IGNITION
KEY SWITCH
RED 5
ORG 30
YEL
GRN
GRN 46
RED
BLU 34
ORG 26
E
8
7
6
5
4
3
2
1
YEL 30
FUSE
PANEL
10 A
10 A
YEL
#45297
#45297
BLU
YEL/BLK
(Not Used)
PLUG
BLK 26
PLUG
BRN/RED
GLO PLUG
TIMER
WHT 4
THROTTLE SWITCH
ORG 3
RED
BLK
BRN 36
BLK/RED
RED 33
GRN 4
E
GRN 4
FF
MM
YEL 4
E
YEL 4
FF
MM
BLK 4
EE
BLK 4
FF
MM
ORG/RED
#FW71684
BLK
BLU 16
ORG/BLK
YEL/RED
RED 10
ORG
BRN/BLK
RED 5
BRN
BLU/BLK
62
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
WHT 8
SAFETY
SWITCH
RED/BLK
2-Conductor Cable
12 Ga. Wire - xxx Denotes Color
16 Ga. Wire - xxx Denotes Color
Ground Wire
WIRING LEGEND
BLU/RED
G NO NC S B
WHT 8
30 AMP
BREAKER
FLASHER
CONTROL BOX WIRING
Part Number
Description
No. Req’d
008658
Modified Control Box
1
008659
Modified Subpanel
1
023802
Safety Switch
1
045055
30A Panel Mount Circuit Breaker
1
021198
Flasher
1
012825
Flasher Mounting Bracket
1
052118
6 Circuit Fuse Panel
1
055449
ATO/ATC 10 Amp Fuse
2
031401
Stud-Type Junction Block (8-Std)
1
020886
Button
2
075330
Hourmeter
1
075309
Temperature Gauge
1
075313
Voltmeter
1
075328
Tachometer
1
075307
Pressure Gauge
1
KU66711-55131
Ignition Key Switch
1
FW71555
Throttle Toggle Switch
1
080526
Switch Boot
1
045297
1/2" Conduit Plug (Gray w/Seal)
2
FW71684
Liquid-Tight Fitting
1
FW71356
16-Pin Male Insert
1
FW71359
16-Pin Electrical Housing Hood
1
008656
Control Box Decal
1
KU15694-65592
Glo Plug Timer
1
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
63
2
BEARING & SEAL ASSEMBLY
NOTE:
ITEM #1 (BEARING & SEAL ASSY)
INLUDES ITEMS #2 - 9.
2“ AGITATOR SHAFT
THROUGH BACK SIDE
3
4
APPLY (1) SOLID, CONTINUOUS
BEAD OF SILICONE ADHESIVE
AROUND OUTER EDGE ON THE
INSIDE FACE OF THE CLAMPING
RING BEFORE INSTALLATION.
5
6
7
8
9
OUTSIDE
OF TANK
10
NOTE:
TO TIGHTEN, TURN THE NUT - NOT THE BOLT.
TORQUE TO 25 FT LBS. - DO NOT OVER TORQUE.
11
AGITATOR ASSEMBLY
16
NOTE:
ITEM #12 (AGITATOR ASSY)
INLUDES ITEMS #13 - 20.
19
20
13
13
17
16
16
14
15
18
13
16
17
DRIVE
END
64
13
14
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
AGITATOR & SEAL ASSEMBLY
Ref. No.
1
Part Number
Description
012529
Bearing and Seal Assembly
No. Req’d
2
2
012527
Inner Clamping Ring w/Studs
1 per
3
012528
Agitator Shaft Seal
1 per
4
012525
Outer Clamping Ring
1 per
5
012451
Flangette
1 per
6
012450
2" Dia. Ball Bearing
1 per
7
012452
Flangette w/Lube Coupling
1 per
008154
Lube Coupling Adapter
1 per
8
012605
Agitator Seal Washer
4 per
9
000Y08
Agitator Hex Nut
4 per
10
012625
2" Split Lock Collar
2
11
007705
Grease Fitting
2
022407
Grease Line Elbow
2
012520
Bulk Head Fitting
2
012521
Grease Line Hose
2
12
012505
Agitator Assembly
1
13
X1240
3/4-10 UNC x 2-1/2" Lg. Hex Hd. Cap Screw
8 per
(Bolt-On Paddles)
14
F330-0010-02
Bolt-On Paddle w/Identification Hole
2 per
15
012495-01
Drive Stub Shaft
1 per
16
Y08L
3/4-10 UNC Lock Nut
16 per
17
X1236
3/4-10 UNC x 2-1/4" Lg. Hex Hd.Cap Screw
8 per
(Stub Shaft Flange Only)
18
012502
Main Agitator Section
1 per
19
012496-01
Idle Stub Shaft
1 per
20
F170-0003-01
Bolt-On Paddle
2 per
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
65
7
5
4
6
3
2
1
31
9
8
25
26
27
30
22
23
24
28
21
20
19
18
9
10
11
12
12
66
16
13
14
17
15
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
29
HYDRAULIC SYSTEM
Ref. No.
Part Number
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
011783
160709
160303
021617
021618
008654-05
FW71711
008293
023652
008654-03
008654-06
008606
012333
055308
008654-04
008640
008603
008654-01
055359
008654-02
023617
022346
011936
012044
012083
160307
011648
008660
160236
022592
080329
Fill Cap
1" NPT x 3/4" NPT Bell Reducer
3/4" NPT Close Nipple
Return Line Filter
Filter Element
3/4" Dia. x 22" Lg. Hydraulic Hose
90 Degree Adapter
Hydraulic Valve
90 Degree Adapter
3/4" Dia. x 34" Lg. Hydraulic Hose
1/2" Dia. x 31" Lg. Hydraulic Hose
Straight Adapter
Hydraulic Motor
Straight Adapter
1/4" Dia. x 37" Lg. Hydraulic Hose
Hydraulic Pump
90 Degree Adapter
1-1/4" Dia. x 36" Lg. Suction Hose
Straight Adapter
3/4" Dia. x 36" Lg. Hydraulic Hose
Straight Adapter
Standard Tee
Straight Adapter
Pressure Gauge
1-1/4" Ball Valve
1/4" NPT Close Nipple
Suction Strainer
Straight Adapter
1/2" Dia. Pipe Plug
Standard Tee
Sight Gauge
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
No. Req’d
1
1
1
1
1
1
2
1
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
67
5
1
2
7
8
3
9
4
6
REF:
STRUCTURE & RAILING
(See Pages 42-43)
REF:
AGITATOR & SEAL
ASSEMBLY
(See Pages 64-65)
HYDRAULIC AGITATOR DRIVE
Ref. No.
Part Number
Description
1
2
3
4
5
6
7
8
9
012333
012354
012522-02
012522-04
011780
003055B
055103
190127-40
012625
Hydraulic Motor
Hydraulic Motor Mount
Rubber Bushing
Torque Arm Insert
Rigid Coupling
Motor Bushing
Agitator Bushing
Key
Split Collar
68
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
No. Req’d
1
1
1
1
1
1
1
1
2
DISCHARGE HOSE EXTENSIONS
Part Number
Description
No. Req’d
BOOM TAKE OFF SYSTEM
007930-02
007929
002191
160768
010544
006513
Boom Discharge Extension Hose Assembly
1-1/2” x 50 ft. Extension Hose w/ Nipples
2-1/2" Male Brass Adapter
2-1/2" to 1-1/2" Reducer Bushing
2-1/2" Female Coupler
2-1/2" Quick-Coupler Gasket
As Ordered
1 per
1 per
1 per
1 per
1 per
PUMP TAKE OFF SYSTEM
007930-01
007929
001207
002158
006515
011908
Pump Remote Discharge Hose Assembly
1-1/2” x 50 ft. Extension Hose w/ Nipples
1-1/2" Male Brass Adapter
1-1/2" Female Brass Coupler
1-1/2" Coupler Gasket
Remote Valve Operation – Heavy Duty
007711
007710
002158
160540
007740
007710
003243
160309
160763
006102
001207
006621
006604
006096
160761
006622
006605
006096
160761
Pump Take Off Valve Assembly
1-1/2" Full Port Ball Valve
1-1/2" Female Brass Coupler
1-1/2" x 2" Lg. SCH 40 Nipple
Remote Valve Assembly
1-1/2" Full Port Ball Valve
1-1/2" Aluminum Nipple Pipe
1-1/2 " Std. Close Nipple
2" x 1-1/2" Tank Bushing
2" Female Coupler
1-1/2" Male Brass Adapter
Wide Ribbon Nozzle Assembly
Nozzle, Wide Ribbon
2" Male Adapter
2" to 1" Reducer Bushing
Narrow Ribbon Nozzle Assembly
Nozzle, Narrow Ribbon
2" Male Adapter
2" to 1" Reducer Bushing
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
As Ordered
1 per
1 per
1 per
1 per
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
69
13
14
15
15
15
6
5
3
7
12
4
11
8
9
2
1
10
16
17
18
20
21
19
NOTE:
ITEM #1 (HOSE REEL ASSEMBLY)
INCLUDES ITEMS #2 - 9.
21
20
21
70
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
HOSE REEL
ELECTRIC MOTOR
STARTER
CIRCUIT
BREAKER
6 GA. RED
ENGINE
GROUND
POWER
(See Hose Reel Lead
On Page 54)
SOLENOID
6 GA. RED
16 GA. BLUE
6 GA. RED
6 GA. BLACK
PUSH BUTTON
HOSE REEL ASSEMBLY
Ref. No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Part Number
Description
008212
080302
008144
008200
008433
008313
008314
008188
008199
012757-01
003207
003299
011894
F330-0077
F330-0094
F330-0104
F330-0068
008433
F330-0067
012781
012798
Hose Reel and Swivel Assembly
Flanged Riser
Hose Reel Gear
Hose Reel Chain - 69" Lg.
Pinlock w/Brackets Assembly
Idle Side Bearing
Drive Side Bearing
Electric Motor
Chair Sprocket - 11 Tooth
Spring Retainer Plate
1-1/2" Dia. X 90 Degree Swivel Joint
Torsion Spring
Hose Roller and Spool Guide
Hose Reel Canopy
Hose Reel Canopy Support
Hose Reel Mount Cover
Upper Hose Reel Bracket
Pinlock w/Brackets Assembly
Lower Hose Reel Bracket
Hose Reel Lock Angle
Hose Reel Bearing Block
008450
020886
008420
008419
011654
HOSE REEL WIRING
Hose Reel Solenoid Kit
Push Button
70 Amp Circuit Breaker
30 Amp Circuit Breaker
40 Amp Circuit Breaker
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
No. Req’d
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
2
4
1
1
1
1
1
71
18
17
19 15
20
21
23
3
22
7
24
16
1
3 (Inside of Railing -
2
Both Sides of Tank)
7
15
4
5
6
14
7
8
13
12
30
11
9
10
LEFT SIDE
OF UNIT
31
29
32
35
13
15
28
21
27
33
26
7
34
25
72
7
16
14
13
36
34
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
DECALS
Ref. No.
*1
*2
Part Number
023174
011595
Description
No. Req’d
"FINN" Decal
"HydroSeeder®" Decal
2
2
012820 - T170/T280/T330 Decal Sheets
3
4
5
6
7
8
*9
10
*11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
* NOTE:
012821
011790
005188
005187
007230
005186
011690
011662
012661-03
012179
012687
007231-01
007230-01
012819
012817
008286-02
005735
011567
005216
012818
012886-01
012041
012278
023391
031462
031463
012688
020970
012597
011569
012180
031297
007231
006869
"WARNING! Fall Hazard" Decal
"1,500 Gallon" Decal
"1,000 Gallon" Decal
"800 Gallon" Decal
"Service Daily" (Up Arrow) Decal
"500 Gallon" Decal
FINN Nameplate
"U.S. Patent No." Decal
"T170" Decal
"WARNING! Do Not Operate w/o Guards . . ." Decal
"CAUTION. Hydraulic System Instructions" Decal
"Service Weekly" (Down Arrow) Decal
"Service Daily" (Down Arrow) Decal
"BLEEDER VALVE - Open/Close" Decal
"RECIRCULATION VALVE - Close/Open" Decal
"AGITATOR OPERATION" Decal
"VALVE - Open/Closed" Decal
"DANGER! Electrocution Hazard . . ." Decal
"WARNING! Burn Hazard!" Decal
"CLUTCH - Engage/Disengage" Decal
"DANGER! Confined Space Hazard! . . ." Decal
"HydroSeeder® Operating Instructions . . ." Decal
"DANGER! BURN HAZARD!" Decal
"DIESEL FUEL" Decal
"WARNING! Burn Hazard! . . ." Decal
"WARNING! Sever Hazard! . . ." Decal
"CAUTION! Fall Hazard!" Decal
"WARNING! Fall Hazard!" Decal
"CAUTION. Keep This Tank Vent Clean . . ." Decal
"CAUTION. This Connection Is For Remote . . ." Decal
"CAUTION. To Avoid Damage To Suction Cover . . ." Decal
"CAUTION. New Clutch Information"
"Service Weekly" (Up Arrow) Decal
"CAUTION. Seal Lubricator Must Be Kept In Operation . . ." Decal
3
1
1
1
5
1
1
1
2
1
1
2
4
2
1
1
1
1
2
1
1
1
2
1
1
1
1
1
1
1
1
1
2
1
These items are not a part of the Decal Sheets (P/N 012820).
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
73
RECOMMENDED SPARE PARTS AND REPAIR KITS
Part Number
Description
No. Req’d
RECOMMENDED SPARE PARTS
000698
Pump Seal Lubricator Grease (1 Lb. Can)
2
011919
Suction Pipe Seal - 5 In.
3
008472
Suction Pipe Seal - 5 In. x 4 In. Reducer
3
002820
Discharge Pipe Seal
3
006722
Recirculation Pipe Seal
2
006513
Nozzle Coupler Gasket
2
007469
Lube Sticks For Recirculation and Discharge Valves (Box of 24)
4
012623
Air Cleaner Safety Filter Element (3.75-E2)
1
012622
Air Cleaner Main Filter Element (3.75-E1)
1
KU1G521-97010
Fan Belt
1
KU16631-43560
Fuel Filter
1
KU1C010-32430
Oil Filter
1
031245
Snapper Pin – Boom Holddown
1
021618
Hydraulic Filter Element
2
REPAIR KITS
012397
Swivel Repair Kit
005295
Pump Seal Kit Consisting of:
005150
O-Ring
1
006443
Mechanical Seal Assembly
1
006444
Grease Retainer
1
006447
Grease Seal
2
012384
Hydraulic Motor Seal Kit
NOTE:
74
Recommended spare parts are available to avoid unnecessary down time.
Repair Kits are available to recondition parts, which periodically need service.
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
TOOL KIT
Part Number
011703
002191
001042
160309
160768
006512
011706
002191
006604
160766
011707
002191
006605
160766
011890
002191
011861
160769
011891
002191
011860
160769
008476
006513
002190
005220
021375
021741
000698
020365
007469
012681A
012681T
Description
No. Req’d
Long Distance Nozzle Assembly
2-1/2" Male Brass Adapter
1-1/2" Long Distance Brass Nozzle
1-1/2" Standard Close Nipple
2-1/2" To 1-1/2" Reducer Bushing
Nozzle Gasket
Wide Ribbon - Small Nozzle Assembly
2-1/2" Male Brass Adapter
Wide Ribbon - Small Nozzle (50500)
2-1/2" To 1" Reducer Bushing
Narrow Ribbon - Small Nozzle Assembly
2-12" Male Brass Adapter
Narrow Ribbon - Small Nozzle (25500)
2-1/2" To 1" Reducer Bushing
Wide Ribbon - Large Nozzle Assembly
2-1/2" Male Brass Adapter
Wide Ribbon - Large Nozzle (501500)
2-1/2" To 2" Reducer Bushing
Narrow Ribbon - Large Nozzle Assembly
2-1/2" Male Brass Adapter
Narrow Ribbon - Large Nozzle (251500)
2-1/2" To 2" Reducer Bushing
Long Distance Nozzle
2-1/2" Quick Coupler Gasket
Main Tank Drain Cap With Gasket
Impeller Wrench
Grease Gun (Hose Not Included)
12" Whip Hose With 1/8" Male Ends
Grease For Pressure Lubricator (1 Lb. Can)
Multi-Purpose Grease Cartridge
Lube Sticks For Discharge & Recirculation Valves (Box of 24)
Touch-Up Paint (FINN Beige - 4.5 Oz Aerosol)
Touch-Up Paint (FINN Beige - 0.5 Oz. Wet)
Engine Operator's Manual
HydroSeeder® Parts and Operator's Manual
WHEN ORDERING PARTS, BE SURE TO STATE
SERIAL NUMBER OF MACHINE
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
75
NOTES
76
NOTES
77
WARRANTY
Finn warrants to the original Purchaser for use (or rental to others for use) all new construction machinery and attachments therefore manufactured by Finn to be free from defects in material and workmanship for a period of 12 months from
date of purchase or 1200 hours of use, whichever comes first. Replacement parts provided under the terms of this warranty
are warranted for the remainder of the warranty period applicable to the product in which installed, as if such parts were
original components of that product. Finn makes no warranty with respect to (a) allied equipment or trade accessories not
manufactured by it (such as, but not limited to tires, ignitions, starters, hose, batteries, magnetos, carburetors, engines
or like or unlike equipment or accessories), such being subject to the warranty, if any, provided by their respective manufactures; or (b) secondhand, used, altered, or rebuilt machines. Further, the warranty herein expressed shall be rendered null and
void to the extent any defect or failure of the products warranted hereby arises out of or is caused by accessories or component parts not manufactured or supplied by Finn, whether same are supplied by Purchaser, dealers or any other party. THE
WARRANTY DESCRIBED IN THIS PARAGRAPH SHALL BE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.
Upon notification of Finn during the above-stated warranty period of any failure to conform to this warranty, and upon
inspection by Finn to verify said nonconformity and verify the continuing existence of the warranty period, Finn will
provide a new part or a repaired part, whichever Finn elects, to replace the part found to be defective. Such parts will be
provided without charge to the Purchaser during normal working hours at a place of business of a Finn dealer or other
establishment authorized by Finn to effect said repairs or replacements, but Purchaser shall bear all costs of transporting
the product to and from such place of business or establishment. Correction of nonconformities, in the manner and for the
period time provided above, shall constitute fulfillment of all liabilities of Finn under this contract.
THE REMEDIES OF THE USER SET FORTH HEREIN ARE EXCLUSIVE, WITHOUT REGARD TO WHETHER
ANY DEFECT WAS DISCOVERABLE OR LATENT AT THE TIME OF DELIVERY OF THE PRODUCT TO THE
PURCHASER.
The essential purpose of this exclusive remedy shall be to provide the Purchaser with repair or replacement of parts that
prove to be defective within the period and under the conditions previously set forth. This exclusive remedy shall not have
failed of its essential purpose (as that term is used in the Uniform Commercial Code) provided Finn remains willing to
repair or replace defective parts within a commercially reasonable time after it obtains actual knowledge of the existence
of a particular defect.
IN NO EVENT SHALL FINN BE LIABLE FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL OR INDIRECT
DAMAGES, INCLUDING LOST PROFITS OR LOST COMMERCIAL OPPORTUNITIES, WITH RESPECT TO
THE SALE OF THE ABOVE WARRANTED PRODUCT OR ANYTHING DONE TN CONNECTION THEREWITH,
OR FOR PROPERTY DAMAGE SUSTAINED BY A PERSON CLAIMING TO BE A THIRD PART BENEFICIARY OF
A SURVIVING WARRANTY UNDER THE LAW OF ANY JURISDICTION.
NOTICE
FINN CORPORATION URGES THE USE OF ONLY FINN CORPORATION SUPPLIED PARTS AND
ATTACHMENTS TO ASSURE PROPER PERFORMANCE AND SAFE OPERATION OF FINN CORPORATION
EQUIPMENT. INSIST ON PARTS AND ATTACHMENTS MANUFACTURED OR SUPPLIED BY FINN
CORPORATION WHEN YOU PURCHASE, REPAIR OR REPLACE YOUR FINN EQUIPMENT AND
ATTACHMENTS. BECAUSE FINN CORPORATION CANNOT ASSURE THAT PARTS AND ATTACHMENTS
NOT MANUFACTURED OR SUPPLIED BY FINN MEET FINN CORPORATION'S QUALITY STANDARDS,
SPECIFICATIONS, OR OPERATING REQUIREMENTS, OUR WARRANTY IS NOT EFFECTIVE TO THE EXTENT
ANY FAILURE OF OR DEFECT IN A FINN CORPORATION PRODUCT ARISES FROM OR IS CAUSED BY
PARTS, ATTACHMENTS OR COMPONENTS NOT ORIGINATING WITH FINN CORPORATION. USE OF FINN
CORPORATION EQUIPMENT WITH PARTS AND ATTACHMENTS NOT MANUFACTURED OR SUPPLIED BY
FINN COULD RESULT IN PERSONAL INJURY.
Effective December 8, 1995
CALIFORNIA
CALIFORNIA
Proposition 65 Warning
Proposition 65 Warning
The engine exhaust and some of its
constituents are known to the State
of California to cause cancer, birth
defects, and other reproductive harm.
78
Battery posts, terminals and related
accessories contain lead and lead
compounds, chemicals known to the
State of California to cause cancer
and reproductive harm. Wash hands
after handling.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement