AMAX panel - Bosch Security Systems

AMAX panel - Bosch Security Systems
AMAX panel
AMAX panel 2100 | AMAX panel 3000 | AMAX panel 3000 BE | AMAX panel 4000
en
Installation Manual
AMAX panel
Table of Contents | en
3
Table of contents
1
Safety
7
2
Short information
9
2.1
Keypad indicators
9
3
System overview
11
4
Optional modules and peripheral devices
14
4.1
Bosch option bus
14
4.2
Keypad
14
4.2.1
General
14
4.2.2
Address setting
15
4.2.3
Wiring
16
4.2.4
Status indicator
16
4.3
DX2010
17
4.3.1
General
17
4.3.2
Address setting
17
4.3.3
Wiring
18
4.3.4
Status indicator
18
4.4
DX3010
18
4.4.1
General
18
4.4.2
Address setting
19
4.4.3
Wiring
19
4.4.4
Status indicator
20
4.5
B426
20
4.5.1
General
20
4.5.2
Address setting
20
4.5.3
Wiring
20
4.5.4
Status indicator
20
4.6
B450 with B442 or B443
21
4.6.1
General
21
4.6.2
Address setting
21
4.6.3
Wiring
21
4.6.4
Status indicator
22
4.7
DX4010V2
22
4.7.1
General
22
4.7.2
Address setting
23
4.7.3
Wirinig
23
4.7.4
Status indicator
23
4.8
DX4020-G
23
4.8.1
General
23
4.8.2
Address setting
23
4.8.3
Wiring
24
4.8.4
Status indicator
24
4.9
RF radion receiver
25
4.9.1
General
25
4.9.2
Address setting
25
4.9.3
Wiring
25
4.9.4
Status indicator
25
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
4
en | Table of Contents
AMAX panel
5
Installation
26
5.1
Module installation
26
5.2
Battery installation
27
5.3
System power up
28
5.4
System status indicator
29
5.5
Certification
29
5.5.1
EN 50131-3 Grade 2, Environmental Class 2 - AMAX 2100 / 3000 / 3000 BE / 4000
30
5.5.2
NFA2P AFNOR / CNPP - AMAX 2100 / 3000 / 3000 BE /4000
30
5.5.3
INCERT - AMAX 4000
32
5.5.4
SFF - AMAX 2100 / 3000 / 3000 BE / 4000
32
6
Settings
34
6.1
Communication and reporting
34
6.1.1
Receivers
34
6.1.2
Reports
41
6.1.3
Test report duration
46
6.1.4
Dual IP
47
6.1.5
IP communicator
47
6.1.6
Remote access
50
6.1.7
Remote PC
50
6.1.8
Call back and domestic call
51
6.1.9
Ring times
52
6.2
Users and codes
52
6.2.1
User code
52
6.2.2
Installer code
53
6.2.3
Code length
57
6.2.4
Code permissions
57
6.2.5
Force code change
57
6.2.6
Macro configuration
58
6.2.7
Code reporting
58
6.3
Zones
59
6.3.1
Add / delete zone
59
6.3.2
Zone function settings
61
6.3.3
Pulse count duration
74
6.3.4
Cross zone timer
74
6.3.5
Zone indication keypad and event log
74
6.4
Keypads and areas
75
6.4.1
Keypad area
75
6.4.2
Entry/exit timing
76
6.4.3
Common area
77
6.4.4
Keypad indication
77
6.4.5
Keypad lockout
79
6.5
System
79
6.5.1
System setting
79
6.5.2
System view
83
6.5.3
System factory default
84
6.6
Outputs and sirens
85
6.6.1
Outputs
85
6.6.2
Sirens
92
6.7
RF devices
92
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Table of Contents | en
5
6.7.1
RF options
92
6.7.2
RF devices / user
93
6.8
Key programming
93
7
Configuration
96
7.1
Service mode
96
7.2
Programming with a keypad
96
7.2.1
Text keypad programming
7.2.2
LED/LCD keypad programming
106
7.3
Communication with PC software
107
7.3.1
Prerequisites for connecting to A-Link Plus
108
7.3.2
Direct connection
109
7.3.3
Modem connection
109
7.3.4
Network connection
109
8
Address programming
111
8.1
Service mode
111
8.2
Communication and report programming
111
8.2.1
Receiver programming
111
8.2.2
Reports programming
115
8.2.3
IP communicator programming
117
8.2.4
Communication operations programming
121
8.3
User and code programming
122
8.3.1
User code programming
122
8.3.2
Installer code programming
126
8.3.3
Code length programming
126
8.3.4
Code permission programming
126
8.3.5
Force code change
127
8.3.6
Macro programming
127
8.4
Zone programming
127
8.4.1
Add/delete zone programming
127
8.4.2
Zone function programming
133
8.4.3
Pulse count duration programming
137
8.4.4
Zone cross timer programming
137
8.5
Keypad and area programming
137
8.5.1
Keypad area programming
137
8.5.2
Area timing programming
138
8.5.3
Common area programming
139
8.5.4
Keypad indication programming
139
8.5.5
Keypad lockout programming
140
8.6
System programming
140
8.6.1
System setting programming
140
8.6.2
System factory default programming
144
8.7
Output and siren programming
144
8.7.1
Output programming
144
8.7.2
Siren programming
147
8.8
RF device programming
147
9
Troubleshooting
150
9.1
General trouble
150
9.2
Trouble fault inquiry
152
Bosch Sicherheitssysteme GmbH
96
Installation Manual
2016.05 | 08 | F.01U.309.277
6
en | Table of Contents
AMAX panel
10
Maintenance
165
10.1
Firmware upgrade with the ICP-EZRU2 upgrade key
165
11
Technical data
166
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
1
Safety | en
7
Safety
Danger!
Electricity
Injuries due to electricity are possible if the system is not operated correctly or if the system
is opened or modified not accordingly to this manual.
–
Disconnect all Telecommunication Network Connectors before switching off the power.
–
To switch off the power, make sure to have a circuit breaker available.
–
Make sure that the system is switched off during the installation and wiring process.
–
Only open or modify the system accordingly to this manual.
–
Make sure to connect the system to a socket-outlet with a protective grounding contact.
–
Only qualified installers /service personnel are allowed to install this system.
Danger!
Battery
Injuries due to electric shock, fire or explosion are possible if the battery is handled or
connected incorrectly.
–
Always handle the battery carefully and replace it carefully.
–
Make sure that the grounding terminal is always connected and that N, L1 or
xx are
connected correctly.
–
Make sure to first disconnect the positive wire of the battery when removing it from the
system.
–
Be careful when connecting the positive (red) wire and the "BATT +" port of the system.
Make sure not to short-circuit with the "BATT +" port of the AMAX panel or the housing to
prevent electric arc from occurring.
Danger!
Electrostatic-sensitive components
Injuries due to electric shock are possible if anti-static steps are not followed.
Always contact the grounding terminal before installing or altering the system to discharge the
possibly carried static electricity.
Caution!
!
Sensitive components
Damage of sensitive components is possible if the system is not handled carefully or if the
system is opened or modified not accordingly to this manual.
–
Always handle the system carefully.
–
Only open or modify the system accordingly to this manual.
Caution!
!
Battery
Damage or contamination of the system is possible if the battery is not handled correctly or if
the battery is not replaced on a regular basis.
–
Only use a non-spillable battery.
–
Place a label with the last replacement date on the battery.
–
Under normal conditions of use, replace the battery every 3-5 years.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
8
en | Safety
AMAX panel
–
Recycle the battery after replacement according to local regulations.
Caution!
!
Installation
Damage or malfunction of the system is possible if the system is not mounted and installed
correctly.
–
Place the system inside the monitored area on a stable surface.
–
Make sure to mount keypads on the inner side of the monitored area.
–
Once the system is tested and ready to use, secure the enclosure door and additional
enclosures with screws.
Caution!
!
Maintenance
Damage or malfunction of the system is possible if it is not maintained on a regular basis.
–
It is recommended to test the system once a week.
–
Make sure to get the system maintained four times a year.
–
Only qualified installers /service personnel are allowed to maintain this system.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
2
Short information | en
9
Short information
This manual contains detailed and advanced information on installation, settings and
programming of the AMAX panel 2100 / 3000 / 3000 BE / 4000 together with the applicable
keypads, modules and devices.
4
2.1
For information on operating the AMAX panel, refer to the AMAX Operation Manual.
Keypad indicators
The following tables show an overview and a description of the keypad indicator icons.
All keypad types
Keypad Indicator
Status
Definition
on
Area is armed in AWAY mode.
off
Area is not armed in AWAY mode.
Slow flash (1 second lights on/1
Exit time.
Icons
AWAY
second lights off)
Fast flash (0.25 seconds lights on/
System is in programming mode or
0.25 seconds lights off)
code function mode. STAY
indicator flashes simultaneously.
Or:
One or more areas but not all are
in AWAY mode (master keypad)
STAY
on
Area is armed in STAY mode.
off
Area is not armed in STAY mode.
Slow flash (1 second lights on/1
Exit time.
second lights off)
Fast flash (0.25 seconds lights on/
System is in programming mode or
0.25 seconds lights off)
code function mode. AWAY
indicator flashes simultaneously.
When bypass function is
performed, only the STAY indicator
flashes.
Or:
One or more areas but not all are
in STAY mode (master keypad)
MAINS
on
AC main power is normal.
Slow flash (1 second lights on/1
AC main power supply failed.
second lights off)
on
System fault, tamper, bypassed
zone or isolated zone condition is
present and has been viewed but
not restored yet.
FAULTS
Or:
System is in service mode.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
10
en | Short information
AMAX panel
off
System is in normal status.
Flashes
System fault, tamper, bypassed
zone or isolated zone condition
must be acknowledged.
All icons
Flashing
No communication to the keypad.
Status
Definition
on
Zone is triggered.
off
Zone is normal.
Fast flash (0.25 seconds lights on/
Zone was alarmed or is in alarm
0.25 seconds lights off)
status.
Slow flash (1 second lights on/1
Interior zone is in STAY arm mode.
second lights off)
Or:
Only for LED/LCD
Keypad Indicator
Icons
1 2 3 ….
This zone is bypassed or isolated
in the current area (area keypad) /
ZONE (1-8)
There is a bypassed or isolated
zone in this area (master keypad).
Only for LCD
Keypad Indicator
Status
Definition
on
Area is disarmed.
Icons
The following table shows an overview and a description of the keypad sound icons.
Sound Indicator
Definition
Short beep
A keypad button has been pressed.
Short beep, followed by a one-second
The requested operation is refused. Incorrect
beep
operation signal.
Two short beeps
The system accepted the code. The system executed
the requested function.
One short beep every minute
Fault tone, unacknowledged system failure.
One short beep every two seconds
Exit time started.
Continued sound
–
Last 10 seconds on exit time
–
Keypad fault or tamper sound (fault or tamper
to be acknowledged)
–
Keypad alarm sound
Continuous 0.5 second beep, stops
Entry delay time (until alarm occurs or area is
for 0.5 seconds
disarmed)
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
System overview | en
11
System overview
3
RADION
LCD / LED Keypad
Text Keypad
DX2010
B426
DX4020G
Option bus
B450
(B442/B443)
DX4010V2
DX3010
AMAX 3000
AMAX 2100 / 3000
USB
GSM/
GPRS
PSTN
Public
IP network
DSL
Ethernet
GPRS
IP
AMAX SDK
A-Link Plus
Telephone
CMS
Video
Signaling
Figure 3.1: AMAX 2100 / 3000 overview
RADION
LCD / LED Keypad
Text Keypad
DX2010
B426
USB
DX4020G
GSM/
GPRS
PSTN
Ethernet
DSL
Option bus
B450
(B442/B443)
Public
IP network
DX3010
DX4010V2
GPRS
IP
AMAX SDK
A-Link Plus
Telephone
CMS
Video
Signaling
Figure 3.2: AMAX 3000 BE / 4000 overview
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
12
en | System overview
AMAX panel
Wiring diagrams
4
≤ 500mA
/ B450
Figure 3.3: Wiring diagram AMAX 2100 / 3000
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
System overview | en
AMAX panel
R
G
B
13
Y
_ 900mA
AUX 1: <
_ 900mA
AUX 2: <
TIP
TH
RH RING
R
G
B
Y
AUX1 AUX2 AUX2 AUX1
+12V +12V -
Bosch Option
AUX Power
_ 900mA
Bus 2 <
1=
2=
Keypads:
IUI-AMAX-LED8
IUI-AMAX-LCD8
AC
+
Bosch Option
_ 900mA
Bus 1 <
1=
2=
I/O Moduls:
DX2010
DX3010
DX4010
Adr. 103 - 108
Adr. 150 - 151
Adr. 253
Communicators:
DX4020G
B426 / B450
Adr. 134
Adr. 134(6) / 250(9)
RF Receiver:
RF3227E
RFRC-OPT
AC
I∑
_
< 2000mA
IUI-AMAX4-TEXT
IUI-SOL-TEXT
3=
IUI-AMAX3-LED16
4=
IUI-AMAX3-LED8
5-16 Inst. Guide
Transformer
Keypads:
GND
[email protected]
Battery
12V 7Ah
_ 18Ah
12V <
Y
Y
G
G
B
B
R
R
+12V
P0+4
+12V
P0+3
+12V
P0+
COM
P0-2
COM
P0-1
PO+4: _
<
_
PO+3: <
_
PO -2: <
_
PO -1: <
L16
1=
1= (1)
230V ~50Hz
230mA
Fuse 1 A
750mA
750mA
500mA
500mA
supervised
100 Ω - 2,2 k
COM
L15
Factory
Default
L14
Program Key Port
3
COM
1
3
2
L13
Zones
L12
3
COM
♥
Slow flash: Normal state
On: Trouble state
Off: Trouble state
L10
Zones
Wachdog
output
<100mA
_
+
0V
L1a
L1b
2
L11
4
COM
L9
Tamper
PO-5
+12V
L2
L3
COM
L4
L5
L6
COM
L7
COM
L8
IUI-AMAX3 +4 Keypad
3
3
Fire
2
Intrusion
3
2
1
2
3
4
Tamper Switch
Zone Switch
EOL 2,2 k
NO + NC
B
G
3
1
Y
COM
2
1
3
Z1
2
R
3
Figure 3.4: Wiring diagram AMAX 3000 BE / 4000
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
14
en | Optional modules and peripheral devices
AMAX panel
4
Optional modules and peripheral devices
4.1
Bosch option bus
The AMAX panel provides Bosch option bus 1 and option bus 2 (only for AMAX 3000 BE and
AMAX 4000) to connect modules and devices. Each module can be connected to each bus.
A maximum of 14 modules (8 keypads) can be connected to each bus.
The total length of the cable for the connection of all keypads and expansion modules wired to
one option bus must not exceed 700m. Particular modules require limitation in cable distance,
e.g. the last keypad must be placed within 200m.
The AMAX panel tests the communication with the modules and transmits the communication
failure report in case of failure of communication.
Cable Details:
–
R: AUX 12V +
–
B: 12V –
–
G: Data
–
Y: Data
Notice!
AMAX 2100 / 3000 provides 12 VDC power supply with a maximum of 500mA for option bus
1. AMAX 3000 BE / 4000 provides a maximum of 900mA for each option bus 1 and 2. When
the total current of the bus exceeds the limit, an external power supply is required.
Notice!
When a data bus address is changed, the module needs to be re-powered to enable the new
address.
The following overview displays the maximum number of modules that can be connected.
Module
AMAX 2100
AMAX 3000 /
AMAX 4000
3000 BE
Keypads
4
8
16
DX2010
-
3
6
DX3010
1
2
DX3010
DX4010
1
-
DX4010
B426
2 or 1 if B450 with B442 or B443 / DX4020G is used
B450 + B442 GPRS + DX4020G
1
RF receiver
-
1
Table 4.1: Maximum number of modules
4.2
4.2.1
Keypad
General
AMAX panel supports five types of keypad as follows:
–
IUI-AMAX4-TEXT (LCD text keypad)
–
IUI-AMAX3-LED16 (16 zone LED keypad)
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Optional modules and peripheral devices | en
–
IUI-AMAX3-LED8 (8 zone LED keypad)
–
IUI-AMAX-LED8 (8 zone LED keypad)
–
IUI-AMAX-LCD8 (8 zone LCD keypad)
15
Dedicated zones for keypads
Keypads can not be assigned to any zones. Certain zones are dedicated to keypads.
The following table shows which zones are dedicated for keypad 1 – 16.
Panel
Keypad
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
AMAX 2100
5
6
7
8
-
-
-
-
-
-
-
-
-
-
-
-
AMAX 3000 /
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
3000 BE / 4000
4.2.2
Address setting
Address setting for IUI-AMAX4-TEXT, IUI-AMAX3-LED16 and IUI-AMAX3-LED8 Keypads
For IUI-AMAX4-TEXT, IUI-AMAX3-LED16 and IUI-AMAX3-LED8 keypads, the address of the
keypad is programmed with 6-position DIP switch. The address of each keypad is unique.
DIP switch
S1
S2
S3
S4
S5
S6
Keypad address
1
2
3
4
5
6
1
On
Off
Off
Off
Off
Off
2
Off
On
Off
Off
Off
Off
3
On
On
Off
Off
Off
Off
4
Off
Off
On
Off
Off
Off
5**
On
Off
On
Off
Off
Off
6**
Off
On
On
Off
Off
Off
7**
On
On
On
Off
Off
Off
8**
Off
Off
Off
On
Off
Off
9*
On
Off
Off
On
Off
Off
10*
Off
On
Off
On
Off
Off
11*
On
On
Off
On
Off
Off
12*
Off
Off
On
On
Off
Off
13*
On
Off
On
On
Off
Off
14*
Off
On
On
On
Off
Off
15*
On
On
On
On
Off
Off
16*
Off
Off
Off
Off
On
Off
Table 4.2: Keypad address settings
* AMAX 4000
** AMAX 3000 / 3000 BE / 4000
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
16
en | Optional modules and peripheral devices
On
Off
O
N
1
2
AMAX panel
DIP
3
4
5
6
Figure 4.1: 6-Position DIP Switch
DIP switches 5 and 6 are not used.
Address setting for IUI-AMAX-LED8 and IUI-AMAX-LCD8 Keypads
IUI-AMAX-LED8 and IUI-AMAX-LCD8 keypads can be set only to address 1 or address 2 through
the address jumper.
Address 1
Jumper not short-circuited
Address 2
Jumper short-circuited (both metal pins are covered)
Table 4.3: Keypad Jumper Settings
4.2.3
Wiring
The following graphic shows how to wire a keypad to the option bus of the AMAX panel. The
last keypad must be placed within a cable distance of 200m.
AMAX 2100 / 3000
R
Y
G
Keypad
B
R
B
G
Y
R
B
G
Y
AMAX 3000 BE / 4000
Figure 4.2: Connecting a keypad to the AMAX Panel
Notice!
The maximum number of keypads to be added to one option bus is 8.
4.2.4
Status indicator
If all indicators of the keypad are flashing, the keypad loses connection to the AMAX panel.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Optional modules and peripheral devices | en
4.3
DX2010
4.3.1
General
17
The AMAX panel supports DX2010 input expansion modules. Each expansion module supports
up to 8 zone inputs.
For information on the installation, refer to Module installation, page 26.
4.3.2
Address setting
Each DX2010 module connected to the AMAX panel needs its own data bus address.
Data Bus Address
Zones
102***
9 - 16
103**
17 - 24
104**
25 - 32
105*
33 - 40
106*
41 - 48
107*
49 - 56
108*
57 - 64
Table 4.4: DX2010 Address Settings
DIP switch
S1
S2
S3
S4
S5
S6
Data bus address
32
16
8
4
2
1
102***
Off
Off
Off
Off
Off
On
103**
Off
Off
Off
Off
On
Off
104**
Off
Off
Off
Off
On
On
105*
Off
Off
Off
On
Off
Off
106*
Off
Off
Off
On
Off
On
107*
Off
Off
Off
On
On
Off
108*
Off
Off
Off
On
On
On
Table 4.5: DX2010 DIP switch settings
* AMAX 3000 BE / 4000
** AMAX 3000 / 3000 BE / 4000
*** AMAX 3000
On
Off
O
N
1
2
DIP
3
4
5
6
Figure 4.3: DX2010 DIP Switch Settings
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
18
en | Optional modules and peripheral devices
AMAX panel
Notice!
When the data bus address is changed, the module and the panel need to be re-powered to
enable the new address
4.3.3
Wiring
The following table and graphic show how to wire DX2010 to the option bus of the AMAX
panel.
Do not use twisted pair or shielded cables to connect DX2010 to the AMAX panel.
Power Supply
Wire diameter of 0.8mm
Wire diameter of 1.2mm
AMAX panel
30m
76m
AMAX panel (DX2010 out not
305m
610m
305m
610m
used)
External power supply
Table 4.6: Lengths of cable for DX2010
R
Y
G
DX2010
DX2010
AMAX 2100 / 3000
B
TMPR R
B
G
Y
1 COM
TMPR R
B
G
Y
1 COM
R
B
G
_
+
Y
12V
AMAX 3000 BE / 4000
Figure 4.4: Connecting DX2010 to the AMAX panel
4.3.4
Status indicator
LED condition
Denotation
On
Trouble condition:
–
Grounding conductor is not connected or there is a
communication failure between the module and the AMAX
panel
4.4
4.4.1
–
No zones distributed
–
Module address setting error
Stable flash
Normal operation
Off
Power failure
DX3010
General
The AMAX panel supports DX3010 output expansion modules. Each module supports 8 fully
programmable relay outputs.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Optional modules and peripheral devices | en
19
For information on the installation, refer to Module installation, page 26.
4.4.2
Address setting
Each DX3010 module connected to the AMAX panel needs its own data bus address.
Data Bus Address
Outputs
150
5-12
151*
13-20
Table 4.7: DX3010 Address Settings
DIP switch
S1
S2
S3
S4
S5
S6
Data bus address
1
2
4
8
16
Mode
150
On
On
On
On
On
Off
151*
Off
On
On
On
On
Off
Table 4.8: DX3010 DIP switch settings
* AMAX 3000 / 3000 BE / 4000
On
Off
O
N
1
2
DIP
3
4
5
6
Figure 4.5: DX3010 DIP Switch Settings
4.4.3
Wiring
The following table and graphic show how to wire DX3010 to the option bus of the AMAX
panel.
Power Supply
Wire diameter of 0.8mm
Wire diameter of 1.2mm
AMAX panel
12.2m
24.4m
External power supply
305m
610m
Table 4.9: Lengths of cable for DX3010
AMAX 2100 / 3000
R
Y
G
B
DX3010
R
B
G
DX3010
Y
R
B
G
Y
R
_
+
B
12V
G
Y
AMAX 3000 BE / 4000
Figure 4.6: Connecting DX3010 to the AMAX Panel
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
20
en | Optional modules and peripheral devices
4.4.4
AMAX panel
Status indicator
None.
4.5
B426
4.5.1
General
The AMAX panel supports up to three communication modules:
–
ITS-DX4020-G and B426 or
–
B450 with B442 or B445 and B426 or
–
B426 and B426
The B426 Ethernet communication module supports monitored two-way IP communication via
Ethernet to perform alarm transmission, remote programming, and control of the AMAX panel.
Installation
1. Disconnect all power supplies of the AMAX panel before installing B426.
2.
Use the standard three-hole installation mode to install B426 in the enclosure of the
AMAX panel or another enclosure. For more information refer to Module installation, page
26 and to the B426 ethernet communication module documentation.
3.
Use network or direct connection to access the built-in web server when reconfiguring
the module or when connecting the module to the AMAX panel with A-Link Plus.
4.5.2
Address setting
Set the rotary switch to 6 which corresponds to option bus address 134 for the first B426 or
4020G or B450.
Set the rotary switch to 9 which corresponds to option bus address 250 for the second B426.
4.5.3
Wiring
The following graphic shows how to wire B426 to the option bus 1 or 2 of the AMAX panel.
Make sure, that the cable doesn’t exceed 150 meters.
AMAX 2100 / 3000
R
Y
G
B426
B
R
Y
G
B
R
B
G
Y
AMAX 3000 BE / 4000
Figure 4.7: Connecting B426 to the AMAX panel
4.5.4
Status indicator
B426 provides several LED indicators. The following table describes the system status
indicator (blue).
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Optional modules and peripheral devices | en
LED condition
21
Denotation
On
Trouble condition
Stable flash
Normal operation
3 quick flashes
Communication error
Off
Power failure or other failure conditions
Table 4.10: B426 System Status Indicator
4.6
B450 with B442 or B443
4.6.1
General
Use B450 in combination with a plug-in communicator for primary or backup alarm
communication, remote panel programming and other remote applications. The B450 supports
Conettix IP protocol with full authentication, 256 bit AES encryption and resistance to Denial
of Service attacks. B450 also supports compatible Bosch panels using SIA DC-09, CSV-IP. It is
a reliable way to add cellular network communications to existing or new commercial security
and fire installations.
For the AMAX panel, B450 can be used in combination with either B442 or B443 with the
following communication possibilities:
–
B442: GSM (GPRS)
–
B443: GSM (GPRS, EDGE), UMTS
The communication of B443 is faster than B442.
Installation
1. Disconnect all power supplies of the AMAX panel before installing B450.
2.
Use the standard three-hole installation mode to install B450 in the enclosure of the
AMAX panel or another enclosure. For more information refer to Module installation, page
26 and to the B450 Conettix plug-in communicator interface documentation.
4.6.2
3.
Insert SIM card into B442.
4.
Insert B442 into B450.
P
B442 clicks and the module combination is ready to be wired.
Address setting
4
4.6.3
Set the rotary switch to 6 which corresponds to option bus address 134.
Wiring
The following graphic shows how to wire B450 to the option bus of the AMAX panel.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
22
en | Optional modules and peripheral devices
AMAX panel
AMAX 2100 / 3000
R
Y
G
B
B450
R / PWR
Y/A
R
G/B
B
B / COM
G
Y
AMAX 3000 BE / 4000
Figure 4.8: Wiring of B450 with an AMAX panel
4.6.4
Status indicator
B450 with B442 or B443 provide several LED indicators. The following table describes the
heartbeat LED indicator of B450 and the status LED indicator of B442 or B443 (blue).
LED Condition
Heartbeat LED of B450
Status LED of B442 or
B443
Denotation
On
Trouble Condition
Stable flash
Normal Operation
3 quick flashes
Communication error
Off
Power failure or other failure conditions
Stable flash
Normal Operation
3 quick flashes
Communication error
Off
Power failure or other failure conditions
Table 4.11: B450 with B442 System Status Indicator
4.7
DX4010V2
4.7.1
General
The DX4010V2 USB / serial interface module creates a local connection between the AMAX
panel and a serial printer (or a parallel printer with a converter box).
The recommended printer is STAR MICRONICS SP500 SP512MD42.
The printer can be connected to the DX4010V2 via a serial cable.
Installation
1. Disconnect all power supplies of the AMAX panel.
2.
Remove the screws from the enclosure cover to access the DX4010V2 board.
3.
Connect the circuit wiring and install the jumper pins.
4.
Replace the enclosure cover.
5.
Connect a USB or serial cable to the printer.
6.
Enable the print function in the user menu.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
4.7.2
Optional modules and peripheral devices | en
23
Address setting
The option bus address is 253.
On
Off
O
N
1
2
DIP
3
4
5
7
6
8
Figure 4.9: DX4010V2 DIP switch settings
4.7.3
Wirinig
The following graphic shows how to wire a DX4010V2 USB / serial interface module to the
option bus of the AMAX panel.
AMAX 2100 / 3000
R
Y
G
B
DX4010V2
R
Y
R
G
B
B
G
Y
AMAX 3000 BE / 4000
Figure 4.10: Wiring of DX4010V2
4.7.4
Status indicator
None.
4.8
DX4020-G
4.8.1
General
The Conettix ITS-DX4020-G GPRS communication module allows IP communication via
commercial GPRS network. Transmission of alarm information via GPRS is the default for ITSDX4020-G. SMS or USB mode can be chosen for configuration. Remote programming and
control of the AMAX panel is supported.
Installation
1. Disconnect all power supplies of the AMAX panel before installing ITS-DX4020-G.
2.
Insert SIM card.
3.
Use the standard three-hole installation mode to install the ITS-DX4020-G in the
enclosure of the AMAX panel or another enclosure.
4.
Connect the magnetic antenna to ITS-DX4020-G.
For information on the installation, refer to Module installation, page 26.
4.8.2
Address setting
4
Set bus address to 134.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
24
en | Optional modules and peripheral devices
4.8.3
AMAX panel
Wiring
The following graphics show how to wire ITS-DX4020-G to the option bus of the AMAX panel.
Two modes are possible: GPRS and GSM
AMAX 2100 / 3000
Y
R
G
B
DX4020G
R
Y
R
G
B
B
G
Y
AMAX 3000 BE / 4000
Figure 4.11: GPRS mode in support of IP
AMAX 2100 / 3000
1RING
1RING
TIP
TIP
R
Y
G
B
DX4020G
PNL
PSTN
BUS
TIP
AMAX 3000 BE / 4000
R
TH
Y
RH
G
RING
B
R
B
G
Y
Figure 4.12: GSM mode in support of PSTN (Contact ID)
4.8.4
Status indicator
Normally, the AMAX panel tests the communication with the module. In case of a
communication failure, a fault report including the module address is sent.
The following table describes the status LED indicator of DX4020-G.
LED condition
Denotation
On
Normal condition
Flash
Trouble condition
Off
Power failure
Table 4.12: DX4020-G System Status Indicator
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Optional modules and peripheral devices | en
4.9
RF radion receiver
4.9.1
General
25
The RADION receiver OP is a wireless receiver that connects the RADION wireless system
components to AMAX 3000 / 3000 BE / 4000. Features include the following:
–
Cover and wall tamper protection
–
RFID and configuration data contained in persistent memory
–
Detection and reporting of radio frequency interference
–
Support of two types of device enrollment
Installation
1. Disconnect all power supplies of the AMAX panel before installing B450.
2.
Mount the receiver onto a wall in a location accessible for future maintenance using the
provided anchors and screws. For best reception, place the receiver in a central location
among the transmitters. In situations where there is a large distance between the
transmitter and receiver, it might be necessary to install receivers for optimum results.
4.9.2
Address setting
4
Set the rotary switch to 1.
The AMAX panel supports only one receiver.
4.9.3
4.9.4
Wiring
1.
Connect the RADION receiver to the option bus.
2.
Make sure that the cable distance to the AMAX panel doesn’t exceed 300 meters.
Status indicator
The following table describes the system status indicator of the RFRC-OPT RADION receiver.
LED condition
Denotation
On
Normal operation
Stable flash
Receiver is being programmed with the zone and transmitter IDs
from the AMAX panel.
Turns off momentarily
Receiver has obtained a valid transmission from a RADION
transmitter.
3 quick flashes
Communication error and/or self-test failure
Causes:
–
A communication failure between the AMAX panel and the
receiver or
–
Off
An invalid address switch setting
Power failure or wiring failure
Table 4.13: RFRC-OPT RADION receiver system status indicator
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
26
en | Installation
5
AMAX panel
Installation
This chapter describes the installation and the system power up of the AMAX panel.
Danger!
Electricity
Injuries due to electricity are possible if the system is not operated correctly or if the system
is opened or modified not accordingly to this manual.
–
Disconnect all Telecommunication Network Connectors before switching off the power.
–
To switch off the power, make sure to have a circuit breaker available.
–
Make sure that the system is switched off during the installation and wiring process.
–
Only open or modify the system accordingly to this manual.
–
Make sure to connect the system to a socket-outlet with a protective grounding contact.
–
Only qualified installers /service personnel are allowed to install this system.
Caution!
!
Installation
Damage or malfunction of the system is possible if the system is not mounted and installed
correctly.
–
Place the system inside the monitored area on a stable surface.
–
Make sure to mount keypads on the inner side of the monitored area.
–
Once the system is tested and ready to use, secure the enclosure door and additional
enclosures with screws.
5.1
Module installation
The enclosure contains only PCBs and transformers of the fixed AMAX panel for installation,
no other hardware.
1.
Open the knockout holes for wiring in the module.
2.
Position two upper mounting holes on the installation wall with the module.
3.
Pre-install screws on the mounting holes (provided by the installer).
4.
Mount the screws on the module.
5.
Fasten the screws.
6.
Fix the two lower mounting holes with screws.
Notice!
Make sure to choose a appropriate positioning screw kit when you install the system in a nonload bearing wall.
Expansion modules can be placed in the enclosure of the AMAX panel. Several places are
available. Figure 6.1. and figure 6.2 show the standard enclosure installation and the
enclosure installation with a mounting plate.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Installation | en
TIP
L1a
TH
L2
RH RING
L1b
2
L3
COM
R
L4
G
COM
TH
Y
L6
L7
L8
COM
COM
L3
AUX1 AUX2 AUX2 AUX1
+12V +12V -
L2
RH RING
L1b
R
L4
B
L5
♥
2
B
♥
L5
TIP
L1a
1
27
G
COM
Y
-
AC
AC
GND
Y
+
R
B
G
P0+4
L16
P0-1
P0+
P0+3
COM
P0-2
L12
L15
L13
L14
COM
COM
L9
L10
L11
AUX1 AUX2 AUX2 AUX1
+12V +12V -
L7
COM
L8
-
AC
AC
GND
Y
+
G
R
B
P0+
P0+3
P0+4
P0-2
P0-1
L15
L14
L16
COM
COM
L12
L13
COM
L9
L10
L11
COM
Enclosure - Standard
COM
L6
3
EN √
1
4
EN √
Enclosure with mounting plate
Figure 5.1: Enclosure Standard / Enclosure with mounting plate
♥
1RING 1RING TIP
1
TIP
EN √
L8
L7
L6
COM
COM
L3
L5
L2
L4
COM
COM
A
L1
B
COM
G
B
12V
Y
P0-2
R
PWR
GND
-
P0-1
+
P0+
AC
AC
Figure 5.2: Enclosure Standard / Enclosure with mounting plate
5.2
Battery installation
The AMAX Panel supports one sealed lead-acid rechargeable battery. After the battery is fully
charged, it can be used as backup power supply to support the system.
For further information refer to Technical data, page 166.
Danger!
Battery
Injuries due to electric shock, fire or explosion are possible if the battery is handled or
connected incorrectly.
–
Always handle the battery carefully and replace it carefully.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
28
en | Installation
AMAX panel
–
Make sure that the grounding terminal is always connected and that N, L1 or
xx are
connected correctly.
–
Make sure to first disconnect the positive wire of the battery when removing it from the
system.
–
Be careful when connecting the positive (red) wire and the "BATT +" port of the system.
Make sure not to short-circuit with the "BATT +" port of the AMAX panel or the housing to
prevent electric arc from occurring.
Caution!
!
Battery
Damage or contamination of the system is possible if the battery is not handled correctly or if
the battery is not replaced on a regular basis.
–
Only use a non-spillable battery.
–
Place a label with the last replacement date on the battery.
–
Under normal conditions of use, replace the battery every 3-5 years.
–
Recycle the battery after replacement according to local regulations.
How to mount the battery
1. Place the battery on the bottom of the enclosure.
2.
Position the red and black wires.
3.
Connect one end of the black wire to the "BATT -" port of the AMAX panel, and the other
end to the negative (-) pole of the battery.
4.
Connect one end of the red wire to the "BATT +" port of the AMAX panel, the other end to
the positive (+) pole of the battery.
P
Once the installation is complete, the AMAX panel will begin to charge the battery.
AMAX 2100 / 3000
+
BATT _
AMAX 3000 BE / 4000
+
BATT _
_
+
Battery
Figure 5.3: Connection of the battery for AMAX 2100 / 3000 and AMAX 3000 BE / 4000
5.3
System power up
1.
Power up the AMAX panel.
The language setting menu is displayed.
2.
Set the date and time. Otherwise, the system prompts as fault.
P
After the AMAX panel is powered up or reset, it resets to previous arming / disarming
status.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Installation | en
29
To reduce false alarms caused by system power up (or by power supply restoration after both
mains supply and AUX power supply fail), the AMAX panel is does not perform zone tests
within one minute after the system power up.
5.4
System status indicator
The AMAX panel indicates the system status by using the LED status indicator on the system
main board.
Slow flash of red on status indicator (repeating on and off with an interval of one second)
indicates a normal system operation.
5.5
Certification
Prerequisites for certification conform installation
The AMAX panel is certified. To realize a usage of the system conformable to the certification
described in this chapter, the following prerequisites have to be fulfilled:
–
Use one of the following possibilities for devices:
–
Two supervised warning devices (PO-1 PO-2 & PO+) and one ATS 2 communicator
(onboard dialer, B426, D4020 or DX4020G)
–
One self powered warning device and one ATS 2 communicator (onboard dialer,
B426, D4020 or DX4020G)
–
Two communicators, one ATS 2 (onboard dialer, B426, D4020 or DX4020G) and one
ATS 1 (onboard dialer, B426, D4020 or DX4020G)
–
One ATS 3 communicator (DX4020 or B426)
–
Connect all communicators to a central monitoring station.
–
Only use the onboard dialer and the option bus communicator for alarm transmission.
–
Connect one 12V / 7AH or one 12V / 18Ah battery to the system.
–
Ensure the maximum current for all components with a 7Ah Battery to be 550mA.
–
Ensure the maximum current for all components with a 18Ah Battery to be 1500mA
(standby 12h, recharge battery 80% in 72h) (PCB =l 00mA, IUI-AMAX Keypads = 31mA,
DX2010 = 35mA, DX3010 = 10mA, B426 = 100mA, B450 = 180mA, DX4020G = 65mA,
RF3227E = 30mA, RFRC-OPT = 30mA).
–
Make sure to have an indication of the arm / disarm status accessible from outside the
monitored area (this indication can be time limited).
–
Use one of the following methods for the access to the monitored area:
–
Starting the entry procedure by opening a door
–
Indicating the arm / disarm status
–
Preventing the access to the monitored area (e.g. mechanical door strike)
–
Only use the enclosure lock only in non EN setup.
–
Only use the telephone arming in non EN setup.
–
Only mount additional modules (except input module DX2010) inside the enclosure.
–
If one or more communicator modules are mounted in an extra enclosure, this enclosure
must have a tamper protection.
–
Install the tamper skirt on the PCB of the input module DX2010, if the input module
DX2010 is mounted on the external enclosure (AE20).
–
Program the system with the EN settings indicated on the programming sheet.
–
Remove the EN indication (on label) if the system is set without EN parameters.
–
Connect no more than 10 devices to one zone input (Panel, Keypad, Input Module, RFUN,
…)
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
30
en | Installation
5.5.1
AMAX panel
EN 50131-3 Grade 2, Environmental Class 2 - AMAX 2100 / 3000 / 3000
BE / 4000
Certification Body:
VDS Schadenverhütung
Amsterdamer Str. 172
50735 Köln
Website: www.vds.de
The panel complies with the following standards:
EN 50131-3
EN 50131-6
EN 50136-2-1
EN 50136-2-3
5.5.2
NFA2P AFNOR / CNPP - AMAX 2100 / 3000 / 3000 BE /4000
Certification body:
AFNOR Certification
11, rue Francis de Pressensé
93571 LA PLAINE Saint Denis Cedex
Tel: + 33 (0) 1 41 62 80 00
Fax: + 33 (0) 1 49 17 90 00
Website: www.afnor.org, www.marquenf.com
E-mail: [email protected]
Certification body:
CNPP – Certification Department – CNPP Cert.
Route de la Chapelle Réanville
CS 22265
27950 SAINT MARCEL
Tel: + 33 (0) 2 32 53 63 63
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
Installation | en
AMAX panel
31
Fax: +33 (0) 2 32 53 64 46
Website: www.cnpp.com
E-mail: [email protected]
The panel complies with the following standards:
RTC 50131-3 NF3248H58-2011 V1
RTC 50131-6 NF3248H58-2011 V1
Reference:
NF324 H58 2.5
Option 3: Grade 2 (European EN standards) + RTC
Certification number:
1223400001
AMAX 4000
1223400002
AMAX 3000
1223400002
AMAX 2100
Prerequisites for an NFa2p conform installation
For an NFa2p conform installation it is necessary to seal the enclosure either with a sealing
wire or an adhesive seal.
For further information about the sealing wire and the adhesive seal, please reverse directly to
your local Bosch contact.
Sealing the enclosure with a sealing wire
1. Open the pre-opened hole which is on the right of the enclosure.
2.
Pass the sealing wire through this hole, and bring the two wires in the corresponding hole
of the enclosure door.
3.
Seal the sealing lead as near as possible from the enclosure.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
32
en | Installation
AMAX panel
Figure 5.4: Sealing the enclosure with a sealing wire
Sealing the enclosure with an adhesive seal
4 Close the lock, attach the adhesive seal on the enclosure and enclosure door and press
firmly.
Environmental class
When an NFa2p conform installation is made, the environmental class of the panel is “1”
5.5.3
INCERT - AMAX 4000
INCERT certification number (only for AMAX 3000 BE): B-509-0063
5.5.4
SFF - AMAX 2100 / 3000 / 3000 BE / 4000
Certification Body:
VDS Schadenverhütung
Amsterdamer Str. 172
50735 Köln
Website: www.vds.de
Certification Body:
SSF Stöldskyddsföreningen
Tegeluddsvägen 100
115 87 Stockholm
Website: www.stoldskyddsfpreningen.se
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Installation | en
33
The panel complies with the following standards:
SSF 1014 Edition 4 Alarm class 1
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
34
en | Settings
6
AMAX panel
Settings
This chapter describes the settings of the AMAX panel in the same order as they appear in the
menu structure of the text keypad. For an overview of the menu structure, refer to Text keypad
programming, page 96.
The settings can be configured either via a text keypad or via the PC software A-Link Plus.
For information on how to configure the settings via a text keypad and how to navigate a text
keypad, refer to Text keypad programming, page 96.
For information on how to connect the AMAX panel to a PC, refer to Communication with PC
software, page 107.
6.1
Communication and reporting
This section outlines the programming information required for the AMAX panel when
communicating with a base station receiver. These parameters specify the telephone
numbers/IP address to be called, transmission formats, and internet communication options.
6.1.1
Receivers
Receiver telephone number / IP address and port
The AMAX panel can report event information from an on-board dialer, which can call four
different receivers and four different telephone numbers. The dialer reports to receiver 1 to 4
by programming. You can program the dialer with 4 separate telephone numbers/IP addresses
and ports, reporting format type and subscriber ID number, and internet communication
options if necessary.
Example
You can set up dialer 1 to report to receiver 1 in Bosch Network (Conettix) format and set up
dialer 2, dialer 3, and dialer 4 to report to a receiver of a central monitoring station in Contact
ID format only, if dialer 1 is unsuccessful.
How to program a telephone number via a text keypad
1. Enter the digits of a telephone number in the text keypad.
2.
To enter a 4-sec pause in the dialing sequence, enter [*] [3].
A pause might be necessary when the dialer communicates through an old (slower)
telephone exchange or when a PABX system is in place.
How to program a telephone number via address programming
1. Enter one digit of a telephone number in each address for the telephone numbers.
2.
To enter a 4-sec pause in the dialing sequence, insert “13”.
A pause might be necessary when the dialer communicates through an old (slower)
telephone exchange or when a PABX system is in place.
3.
To terminate the input, insert “15”.
Example for address programming
–
To program the telephone number “9672 1055” as the telephone number for receiver 1,
program the following sequence into address 000 - 016:
[9 6 7 2 1 0 5 5 15 x x x x x x x x] (x stands for any digit)
–
To program the number “02 pause 9672 1055”, program the following sequence into
address 000 - 016:
[0 2 13 9 6 7 2 1 0 5 5 15 x x x x x]
The following table shows how to program the numbers, keys, and functions for a telephone
number via address programming or via installer menu programming.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Settings | en
Digit required
35
Number to program via
Button to press via installer
address programming
menu programming
0-9
0-9
0-9
*
11
*1
#
12
*2
4 sec pause
13
*3
Terminal
15
Not required
How to program an IP address and port
1. Program an IP address with 17 digits: digits 1 - 12 for the IP address and 13 - 17 for the
port.
2.
Use no punctuation in the IP address.
3.
If any unit of the IP address has less than 3 digits, use 0 to fulfill the data in the higher
bits.
4.
The remaining 5 digits program the port. Port number ranges from 0-65535.
5.
If a port number has less than 5 digits, use 0 to fulfill the data.
Example
4 To program the IP address “10.16.1.222:80”, enter the following sequence into the
correspondent address:
[0 1 0 0 1 6 0 0 1 2 2 2 0 0 0 8 0]
Notice!
Programming option anti-replay, acknowledge wait time, and pulse interval time are only used
in Conettix IP.
Telephone number for receiver 1 - 4 / IP address and port
When the corresponding data format for above programming address is a network
communication format, it is explained as an IP address, and port. For a non network format, it
is explained as a telephone number.
The AMAX panel contacts the telephone number / IP Address of the central monitoring station
in order to transmit a report. If the contact is successful, the relevant information is
transmitted, and the communicator returns to standby mode.
Contact your monitoring station for the correct telephone number / IP address before you
program these addresses.
Receiver subscriber ID number
Receiver 1 - 4 subscriber ID number
The subscriber ID number is transmitted to identify the calling AMAX panel.
Digits from 0 - 9 and letters from B - F are supported
How to program a subscriber ID number
1. Enter the subscriber ID number in the six addresses provided for each destination.
2.
If a subscriber ID number has less than 6 digits, use 0 to full fill the data in the higher
bits.
Example
4
Program subscriber ID number as 4729 in six addresses: [0 0 4 7 2 9]
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
36
en | Settings
AMAX panel
The following table shows how to program the numbers, keys, and functions for a subscriber
ID number via address programming or via installer menu programming.
Digit required
Number to program via
Button to press via installer
address programming
menu programming
0-9
0-9
0-9
B
11
*1
C
12
*2
D
13
*3
E
14
*4
F
15
*5
Receiver transmission format (Contact ID, SIA, Conettix IP)
Receiver 1 - 4 transmission format
When an event occurs, reports are sent to the central monitoring station via different
communication protocols using the transmission format CID or SIA.
The communication protocols contain various information on the events to be reported, for
example:
–
event code
–
alarm type
–
subscriber ID / ID number 1 and 2 for account number 1 and 2 (4 digits for CID, 6 digits
for SIA)
–
new event or previously reported
–
zone number
–
area number
–
RRCVR (receiver number)
–
LPREF (account prefix)
For reports with the AMAX panel, five kinds of communication protocols are available:
–
Contact ID (default)
–
SIA DC03
–
Conettix IP
–
SIA DC09
–
SIA DC09 (2x ID)
Which communication protocols can be used in a particular case depends on the receiver of
the provider. Therefore, contact your provider.
TCP/UDP transmission
For SIA DC09 and SIA DC09 (2x ID) both TCP and UDP are available.
Protocols overview
The following table shows an overview of the available communication features for each
communication protocol.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
Settings | en
AMAX panel
Communication features
37
Communication protocol
Contact ID
SIA DC03
Connetix IP SIA DC09
SIA DC09
(2x ID)
Transmission via
√
√
telephone line
Transmission via IP
√
√
√
√
√
√
CID
CID/SIA
CID/SIA
Ethernet
Transmission via IP
Wireless
Transmission format
CID
SIA
The following table shows an overview of the available configurations for each communication
protocol.
Configurations
Transmission format
Contact ID
SIA DC03
Connetix IP SIA DC09
SIA DC09
(2x ID)
Phone number
√
√
IP address and port
Subscriber ID*
√
√
√
ID number 1*
√
√
√
√
√
ID number 2*
√
LPREF
√
√
RRCVR
√
√
TCP/UDP transmission**
√
√
Encryption option
√
√
Time zone
√
√
Local time
√
√
synchronization
* 4 digits for CID, 6 digits for SIA
** SIA DC09 TCP only works with B426 v03.04.001 or later and B450 v03.03.001 or later
Receiver transmission encryption
The transmission encryption function is only available for the transmission format SIA DC09
and SIA DC09 (2x ID).
The following transmission formats can be selected:
–
128 bits key
–
192 bits key
–
256 bits key
The maximum length of the encryption key is 64 digits.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
38
en | Settings
AMAX panel
Time zone
This option is used to set the GMT offset for the time zone of the panel. Only one time zone
can be set for the panel.
Local time synchronization
The option enables or disables the synchronization with the local time.
Events and message overview
The following table shows an overview of the events and their message formats.
Event Description
CID
SIA
format format
SYSTEM RESET
ALL
KP
Dialer
EN
Event
Recall
Event
Event
√
BURG ALARM
1130
BA
√
BURG ALARM RESTORE
3130
BR
√
BURG 24-HOUR
1133
BA
√
BURG 24-HOUR RESTORE
3133
BH
√
SENSOR FAULT
1380
BT
√
SENSOR FAULT RESTORE
3380
BJ
√
SENSOR BYPASS
1570
BB
√
SENSOR BYPASS RESTORE
3570
BU
√
SENSOR TAMPER
1144
TT
√
SENSOR TAMPER RESTORE
3144
TJ
√
ARM AWAY
3401
CL
DISARM AWAY
1401
ARM STAY
√
√
√
√
√
√
√
√
√
√
√
√
√
OP
√
√
√
3441
CL
√
√
√
DISARM STAY
1441
OP
√
√
√
KEYPAD PANIC
1120
PA
√
√
KEYPAD FIRE
1110
FA
√
√
KEYPAD EMERGENCY
1100
QA
√
√
DURESS
1121
HA
√
√
KEYPAD TOOMUCH RETRY
1421
JA
√
BATTERY LOW
1309
YT
√
√
BATTERY RESTORE
3309
YR
√
√
AC FAIL
1301
AT
√
√
AC RESTORE
3301
AR
√
√
AUX POWER
1300
IA
√
AUX POWER RESTORE
3300
IR
√
COMM TEST
1602
RP
2016.05 | 08 | F.01U.309.277
Installation Manual
√
Bosch Sicherheitssysteme GmbH
AMAX panel
Settings | en
Event Description
CID
SIA
format format
ALL
KP
Dialer
EN
Event
Recall
Event
Event
CONFIG CHANGED
1306
YG
√
√
COMM FAIL
1350
YC
√
√
COMM RESTORE
3350
YK
√
√
EXTERNAL MODULE FAULT
1333
EM
√
EXTERNAL MODULE RESTORE
3333
EN
√
EXTERNAL MODULE TAMPER
1341
ES
√
EXTERNAL MODULE TAMPER RESTORE
3341
EJ
√
DATE TIME SET
1625
JT
√
JV
√
USER CODE CHANGE
SERVICE MODE ON
√
SERVICE MODE OFF
√
ENTER PROGRAM MODE
LB
√
EXIT PROGRAM MODE
LX
√
√
√
√
1351
LT
√
√
PHONE LINE RESTORE
3351
LR
√
√
PANIC 24-HOUR
1120
PA
√
PANIC 24-HOUR RESTORE
3120
PH
√
FIRE 24-HOUR
1110
FA
√
FIRE 24-HOUR RESTORE
3110
FH
√
FIRE UNVERIFIED
1378
FG
√
OUTPUT FAULT
1320
YA
√
OUTPUT RESTORE
3320
YH
√
DAYLIGHT SAVING TIME +1h
1625
JT
√
√
DAYLIGHT SAVING TIME -1h
1625
JT
√
√
1422
SOFTWARE UPDATE
√
√
√
√
√
YZ
√
√
RB
√
CLOCK FAIL
1626
TAMPERZONE TAMPER
1137
TA
√
TAMPERZONE TAMPER RESTORE
3137
TH
√
ZONE EXT FAULT
1150
UA
√
Installation Manual
√
√
1412
√
√
JP
REMOTELINK SUCCESS
Bosch Sicherheitssysteme GmbH
√
√
PANEL ACCESS
√
√
PHONE LINE FAIL
FAULT OVERRIDE
39
√
√
√
√
2016.05 | 08 | F.01U.309.277
40
en | Settings
AMAX panel
Event Description
CID
SIA
format format
ALL
KP
Dialer
EN
Event
Recall
Event
Event
√
√
√
ZONE EXT FAULT RESTORE
3150
UR
√
DELAY EXIT
1134
BA
√
DELAY EXIT RESTORE
3134
BR
√
BURG ALARM VERIFIED
1139
BV
√
√
BURG ALARM UNVERIFIED
1130
BG
√
√
IP MODULE FAULT
1333
EM
√
√
IP MODULE RESTORE
3333
EN
√
√
IP MODULE CFG CHANGE
√
IP MODULE NETWORK TROUBLE
√
IP MODULE NETWORK RESTORE
√
PRINTER MISSING
1336
VZ
√
PRINTER MISSING RESTORE
3336
VY
√
PRINTER ERROR
1335
VT
√
PRINTER ERROR RESTORE
3335
VR
√
PRINTER MODULE MISSING
1333
EM
√
PRINTER MODULE MISSING RESTORE
3333
EN
√
RF RECEIVER MISSING
1333
EM
√
RF RECEIVER MISSING RESTORE
3333
EN
√
RF RECEIVER TAMPER
1341
ES
√
RF RECEIVER TAMPER RESTORE
3341
EJ
√
RF RECEIVER FAULT
1333
ET
√
RF RECEIVER FAULT RESTORE
3333
ER
√
RF RECEIVER JAM
1344
XQ
√
RF RECEIVER JAM RESTORE
3344
XH
√
RF RECEIVER CONFIGURATION CONFLICT
√
RF RECEIVER CONFIGURATION CONFLICT
√
√
RESTORE
RF POINT MISSING
1381
UY
√
RF POINT MISSING RESTORE
3381
UJ
√
RF POINT BATTERY FAULT
1384
XT
√
RF POINT BATTERY FAULT RESTORE
3384
XR
√
RF POINT FAULT
1380
BT
√
RF POINT FAULT RESTORE
3380
BJ
√
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Settings | en
Event Description
CID
SIA
format format
ALL
KP
Dialer
EN
Event
Recall
Event
Event
RF REPEATER MISSING
1150
UZ
√
RF REPEATER MISSING RESTORE
3150
UH
√
RF REPEATER BATTERY FAULT
1384
XT
√
RF REPEATER BATTERY FAULT RESTORE
3384
XR
√
RF REPEATER TAMPER
1383
TA
√
RF REPEATER TAMPER RESTORE
3383
TH
√
RF REPEATER AC FAULT
1334
YP
√
RF REPEATER AC FAULT RESTORE
3334
YR
√
RF KEYFOB BATTERY FAULT
1384
XT
√
RF KEYFOB BATTERY FAULT RESTORE
3384
XR
√
RF KEYFOB PANIC ALARM
1120
PA
√
RF KEYFOB SILENT ALARM
1122
HA
√
RF CHANGE KEYFOB
41
√
RF POINT ENCLOSURE TAMPER
1383
TA
√
RF POINT ENCLOSURE TAMPER RESTORE
3383
TH
√
RF POINT MISSING ALARM
1150
UZ
√
RF POINT MISSING ALARM RESTORE
3150
UH
√
√
√
√
√
Receiver network programming options
When the AMAX panel transmits a report via a network, the following options should be
programmed other than the IP address and port.
Anti reply
Anti replay prevents unauthorized messages from being sent to the Central Monitoring Station
and being recognized as originating from the AMAX panel.
4
Contact your central monitoring station for the correct setting.
Acknowledge wait time
When no callback from the receiver after the acknowledge time is reached, the AMAX panel
takes it as an unsuccessful communication and makes another attempt. The time ranges from
5 to 99 sec.
4
Contact your central monitoring station for the correct setting.
Network polling time
The polling is used for both panel and remote receiver to know whether the network
connection is good or not. Each time when polling is due, the AMAX panel will send a polling
message. The polling time ranges from 1 to 999 minutes.
6.1.2
1.
For time less than 3 digits, use 0 to fulfill.
2.
Contact your central monitoring station for the correct setting.
Reports
System reporting
Report transmission sequence
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
42
en | Settings
AMAX panel
If the event has disabled the report (option 0), no report is sent out. If the report has any
destination to contact the panel (option 1 - 11), It will call the related destination by related
reporting format type and subscriber ID number.
Attempt rules:
1.
Attempt times and duration
–
Within the report expiring time the AMAX panel will retry sending the report to each
enabled destination till the report has been sent to the destination, or till the report
buffer overflows and the old report is replaced by new incoming reports.
–
For each enabled destination, the retry interval time between two retries is 15
seconds for the 1st retry to 4th retry, and the retry interval time between two retries
is 10 minutes for the 5th retry to 8th retry, after the 8th retry the retry interval time
between two retries is 60 minutes.
2.
Attempt priority
–
The attempt priority is destination 1, 2, 3, 4 Domestic. The disabled destinations will
be ignored.
3.
Communication fail fault
–
If the attempt times for one destination reaches 4, the system will cause the
communication fail fault for this destination.
4.
Backup destination process
–
The AMAX panel can save up to a maximum of 50 un-reported events. If the unreported events are more than 50, it will delete earlier event and only save the last
50 events in the buffer to send out.
Sequential logic to send report
–
If the event reporting path is disabled, the relevant reports will not be sent.
–
If the event reporting path is set to a single path (receiver 1, 2, 3 or 4), the AMAX panel
will send a report to the corresponding path.
–
If the event reporting path is set to more than one path (e.g. receiver 1, 2, 3, 4) and any
of these paths fails, the reporting will fail.
–
If the event reporting path is set to one or more receivers with other receivers as backup,
the AMAX panel will send the report to the main receivers first. Only this reporting fails,
the AMAX panel attempts to send the report to the backup receivers in succession.
Communication path fault will occur when all valid paths fail. Communication path fault
will recover when any one of the paths recovers.
Display of faults
When multiple reports are queued for delivery, the communication path fault is displayed as a
logic or relationship. Example:
Set zone status recovery report to send report to receiver 1. Set keypad emergency report to
send report to receiver 1, with receiver 2, 3, and 4 as backup.
Communication path fault is as follows: When communication paths 1, 2, 3, and 4 all fail, only
the illumination of zone indicator 1 expresses that communication path 1 of the zone status
recovery report fails and the all communication paths 1, 2, 3 and 4 of the keypad emergency
report fail as well.
Communication path fault recovery is as follows:
–
When communication path 1 fault recovers, zone indicator 1 goes off, indicating that the
communication path 1 fault of the zone status recovery report recovers and the
communication part 1 fault of the keypad emergency report recovers
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
Settings | en
AMAX panel
–
43
When any one path fault of communication paths 2, 3, and 4 recover, as the
communication path fault is displayed as a logic or relationship, zone indicator 1 still
illuminates, indicating that the communication path 1 fault of the zone status recovery
report has not be recovered, but the path fault of the keypad emergency report has been
recovered
Zone status reporting and zone recovery reporting
Zone restore report
Alarm report
In arming status, in case of alarm event, the alarm report will be sent.
Alarm recovery report
In arming status, when a zone is restored, a zone recovery report is sent either if the lock-out
option for the zone is disabled or if the lock-out option for the zone is enabled and the alarm
output time has ended.
If the non-24-hour zone is not recovered in disarming, the system will automatically send a
zone recovery report. The 24-hour zone sends the recovery report only when the zone
recovers.
Zone fault report
If the zone is triggered at the end of exit delay, a zone fault report will be sent, indicating that
the zone is automatically bypassed by the system. At the end of exit delay time, the 24-hour
zone in triggering status will not send the fault report, i.e. the 24-hour zone will not be
automatically bypassed.
The non 24-hour zone fault recovery report will be sent when the zone recovers or the system
disarms. For the 24-hour zone, only the alarm recovery event will occur.
The zone fault occurs when the zone is triggered and recovers when the zone is normal. Zone
fault will occur when one of the following conditions is met:
–
For 24-hour zone, (internal) instant zone, if the forced arming option is set to allow, the
zone fault event will occur when the arming operation is executed while the zone is in
triggering status
–
When the zone is locked
–
For (internal) delay and (internal) follow zone, if they are still in triggering status at the
end of exit delay, zone fault event will occur
–
For 24-hour zone, if it is in triggering status when the bypass is cancelled, zone fault
event will occur
Fault recovery conditions:
–
–
Zone resumes to normal conditions
When the failed (internal) delay zone, (internal) instant zone and (internal) follow zone
are disarmed, the fault recovery event will occur even if the zone is still in triggering
status
Zone bypass report
After a manual zone bypass operation is executed, the zone is bypassed and a relevant zone
bypass report is sent.
The zone bypass will be recovered when the system is disarmed and the zone bypass recovery
report will also be sent while disarming.
Zone tamper alarm
In case of zone tamper event, the tamper report will be sent. When zone tamper recovers, the
system status report will be sent.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
44
en | Settings
AMAX panel
AWAY arm / disarm report
The system disarming report is sent at the disarming command and the system arming report
is sent when the arming succeeds.
Duress report
The duress report is sent at the disarming command. The duress report will not be sent in the
operation of arming, but sent with ordinary disarming report. The duress report has no
corresponding alarm recovery report.
Key switch arming
Sends system arming report when the transient key switch or locking key switch is used to
arm areas.
Quick arming
Sends system arming report when the keypad is used for quick arming.
Telephone arming
Sends system arming report when the telephone is used for arming of the panel.
Telephone arming is only available when there is Area 1 and 1 Area alternatively in the system.
RPC arming
Sends system arming report when the remote PC is used to arm areas through network or
telephone connection.
STAY arm / disarm report
The perimeter disarming report is sent at the disarming command and the perimeter arming
report is sent when the arming succeeds.
Quick arming
Sends perimeter arming report when the keypad is used for quick arming.
RPC arming
Sends perimeter arming report when the remote PC is used to arm areas through network or
telephone connection.
AC fault report recovery
When the system detects a recovery of the AC power that lasts longer than the AC power
delay report time, the report will be sent.
AC fault report domestic
When the system detects disconnection of AC power and after the AC fault delay time has
ended, the report will be sent.
System status reports
–
External module fault reports
–
–
System tamper report and recovery report
Zone expansion module fault report and recovery report for zone expansion module
1-6
–
Output expansion module fault report and recovery report for output expansion
module 1 or 2
–
Network module fault report and recovery report for network module 1 or 2
–
Keypad fault report and recovery report
–
Zone expansion module tamper report and recovery report
–
Keypad tamper report and recovery report
–
Auxiliary power fault report
–
Auxiliary power fault restore report
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
Settings | en
AMAX panel
–
45
Battery low voltage fault report
When the battery voltage is lower than 11.0V or battery low voltage is detected in the
dynamic battery test, the AMAX panel will send the battery low voltage report.
The system continuously monitors the battery voltage and will perform a dynamic battery
test each time the system is armed, when the system is reset or in every battery check
interval.
–
Battery low voltage fault recovery report
When the battery voltage is lower than 12.0V or recovery to normal voltage is detected in
the dynamic battery test, the battery low voltage fault recovery report will be sent.
–
Access denial report
When the times of entering wrong code reaches the specified value, an access denial
report will be generated and alarm will be made. For more information on how to set a
limit to failure attempts, refer to Follow EN standard, page 79 and Keypad lock count,
page 79.
This function is used to prevent unwanted users from accessing the system. When the
number of incorrectly entered codes reaches a specific value, the AMAX panel will
execute following actions:
–
Activate alarm siren and other alarm outputs
–
Lock the keypad in which the incorrect codes have been entered for 3 minutes
–
Send an access denial report
–
On-board output 1 - 2 fault report and recovery report
–
Communication path 1 - 4 fault report and recovery report
–
Changing programming parameters report
System report with domestic
The system reports for domestic calls behave in the same way as the system status reports.
Panic alarm report
In case of panic, a panic alarm report can be executed. The panic alarm report has no
corresponding alarm recovery report.
4
For information on how to execute a panic alarm report, refer to Panic 2 button alarm,
page 46.
Fire alarm report
In case of fire, a fire alarm report can be executed. The fire alarm report has no corresponding
alarm recovery report.
4
For information on how to execute a fire alarm report, refer to Fire 2 button alarm, page
46.
Medical alarm report
In case of a medical emergency, a medical alarm report can be executed. The medical alarm
report has no corresponding alarm recovery report.
4
For information on how to execute a medical alarm report, refer to Medical 2 button alarm,
page 46.
Automatic test report
The system supports sending automatic test report. The interval of sending automatic test
reports is configurable.
4
For more information on automatic test reports, refer to Test report duration, page 46.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
46
en | Settings
AMAX panel
Report expiry time
If a report or a domestic call is sent but can not be acknowledged, this option defines the
amount of time in minutes of how long the report or a domestic call will be sent. After the
defined amount of time has been passed and the report or a domestic call still has not been
acknowledged, it will be ignored. Possible values are 1 to 255 minutes. If 000 or any other
value is entered, the report or a domestic call will be sent without time limit until it is
acknowledged.
Report delay entry time
This option defines the delay time until a report is send or a domestic calling is initiated when
an alarm occurs during entry time. The possible value range is 00-99 seconds. If 00 is selected
and an alarm occurs during entry time, a report is send immediately or the domestic calling is
initiated immediately after the entry time ends. The default setting is 30.
Panic 2 button alarm
If the user presses and holds both the buttons 1 and 3 on the keypad for 3 seconds, or
presses and holds both [#] and [*] for 3 seconds, the emergency alarm will be triggered. The
following settings are possible:
–
Disabled
–
Report will be send
–
Siren will be triggered
–
Report will be send and siren will be triggered.
Fire 2 button alarm
If the user presses and holds both the buttons 4 and 6 on the keypad for 3 seconds, the fire
alarm will be triggered. The following settings are possible:
–
Disabled
–
Report will be send
–
Siren will be triggered
–
Report will be send and siren will be triggered.
Medical 2 button alarm
If the user presses and holds both the buttons 7 and 9 on the keypad for 3 seconds, the
medical aid alarm will be triggered. The following settings are possible:
6.1.3
–
Disabled
–
Report will be send
–
Siren will be triggered
–
Report will be send and siren will be triggered.
Test report duration
There are two types of automatic test reports, configurable periodic reports and regular daily
reports. The periodic test is sent according to the configuration (interval, hour and minute)
and the local time. Therefore, the date and time of the system has to be set correctly. When
the time that is configured as hour and minute is reached, a periodic test report is send. The
next periodic test report is sent after the configured interval and is not influenced by any
other reports sent in between periodic test reports.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Settings | en
47
Test report interval
The test report interval can be set to 1 hour, 2 hours, 3 hours, 4 hours, 6 hours, 8 hours, 12
hours or 24 hours.
The periodic test report can be disabled. Regular daily automatic test reports will be sent
instead.
Test report hour
In this option the reference hour from which the test report interval will be started can be
entered. Values from 00 - 23 are valid. An invalid value will be treated as 00.
Test report minute
In this option the reference minute from which the test report interval will be started can be
entered. Values from 00 - 59 are valid. An invalid value will be treated as 00.
6.1.4
Dual IP
Dual IP Settings are valid only when used with Conettix IP communication format. IP module 1
is ITS-DX4020-G module or B426 module; IP module 2 is B426 module. IP module 2 does not
support RPC connection.
When the report is transmitted with Conettix IP Communication, some reports might be
missed. It is recommended not to separately use the ITS-DX4020-G module. If the ITS-DX4020G module is used, other network modules (e.g. B426) or the public telephone network can be
set as backup channel to ensure that no reports are missed.
The communication path of B426 / ITS-DX4020-G / B 450 is as follows:
Module
Address Setting
Corresponding
Communication Path
Module 1: B426 module 1 / ITS-
134
Paths 1 and 2
250
Paths 3 and 4
DX4020-G / B 450
Module 2: B426 module 2
Only when IP module 1 is used and set to paths 1 to 4, the report can be sent to those paths.
6.1.5
IP communicator
Modules
The modules B426 and B450 can be connected to the AMAX panel and used as IP
communicators.
B426 can be set as module 1 or 2. B450 can only be set as module 1.
For more information on B426 and B450, refer to the corresponding manuals.
IPv6 mode
This option enables / disables the IPv6 mode. If this option is disabled, the IPv4 mode is used.
IPv4 DHCP
This option enables / disables the IPv4 DHCP. If a DHCP service is available is this option is
enabled, the IPv4 address, the IPv4 subnet mask, the IPv4 default gateway, the IPv4 DNS
server IP and alternative IPv4 DNS server IP are configured automatically.
IPv4 address
This option sets the IPv4 address. Possible values are 0.0.0.0 to 255.255.255.255.
This option is only configurable if IPv4 DHCP is disabled.
IPv4 subnet mask
This option sets the address of the IPv4 sub-network mask. Possible values are 0.0.0.0 to
255.255.255.255.
This option is only configurable if IPv4 DHCP is disabled.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
48
en | Settings
AMAX panel
IPv4 default gateway
This option sets the address of the local network gateway to the internet or intranet. Possible
values are 0.0.0.0 to 255.255.255.255.
This option is only configurable if IPv4 DHCP is disabled.
IPv4 DNS server IP
This option sets the IPv4 DNS server IP address in static IP mode. Possible values are 0.0.0.0
to 255.255.255.255.
This option is only configurable if IPv4 DHCP is disabled.
IPv6 DNS server IP
This option sets the IPv6 DNS server IP address in static IP mode. Possible values are
0000:0000:0000:0000:0000:0000:0000:0000 to FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF.
UPnP (universal plug and play) enable
This option enables / disables devices to connect to the network. If this option is enabled, IP
devices discover each other's presence on the network and can connect to communicate. If
this option is enabled, a router can forward port numbers through the keypad, allowing
reports to reach receivers behind the router.
HTTP port number
This option defines the web server port number. Possible values are 1 to 65535.
If TLS enhanced security is enabled, HTTPS is applied instead of HTTP. The default value for
HTTPS is 443.
ARP cache time (sec)
This option defines the time-out for ARP cache entries (in seconds). Possible values are 1 to
600.
Web/USB access enable
This option enables / disables authorized users to view and modify the B426 configuration
parameters through a standard web browser or the B450 configuration through a USB
connection.
Web/USB access password
This option defines the password required to log in for web access. Possible values are ASCII
printable characters. The length must be 4 to 10 characters.
Firmware upgrade
This option enables / disables the module’s firmware to be modified via the external web
interface. If this option is disabled, the module’s firmware has to be modified through the
control panel.
Module hostname
This option allows the user to customize a hostname for the module. Once set, this hostname
can be used to contact the control panel via RPS over network. If enabled, a web browser can
connect to this communication unit at this hostname for the purposes of configuration and
diagnostics.
If this field is left blank, the module will determine its hostname based on its MAC address
(the factory default hostname).
Possible values are characters (letters, numbers and dashes). The maximum length is 63
characters.
Unit description
This option allows the user to enter a description of the module (location, attributes, etc.).
Possible values are ASCII printable characters. The maximum length is 20 characters.
TCP/UDP port number
This option defines the local port number that the module listens to for incoming network
traffic.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
Settings | en
AMAX panel
49
The TCP/UDP port is typically configured as 7700 when the control panel is communicating
with the B5512, B4512 and B3512, a central station receiver, RPS, or automation.
Possible values are 0 – 65535. Port numbers are assigned in various ways based on three
ranges:
System ports
0 - 1023
User ports
1024 - 49151
Dynamic or private ports
49152 - 65535
4
In order to limit unwanted traffic, select a number above 1023.
TCP keep alive (sec)
This option defines the time (in seconds) between TCP keep-alive transmissions to verify that
an idle connection is still active.
Possible values are 0 – 65.
Alternative IPv4 DNS server IP
This option sets an alternate IPv4 DNS server IP address.
If the module fails to obtain an address from the primary server, the alternate DNS server will
be used if one has been specified. The alternate IPv4 DNS address has a dot decimal notation,
which consists of the four octets of the address expressed separately in decimal and
separated by periods. Possible values are 0.0.0.0 to 255.255.255.255. A default value is
entered if the DHCP service is available.
This option is only configurable if IPv4 DHCP is disabled.
Alternative IPv6 DNS server IP
This option sets an alternate IPv6 DNS server IP address.
If the module fails to obtain an address from the primary server, the alternate DNS server will
be used if one has been specified. The alternate IPv6 DNS address has a hexadecimal
notation, which consists of the eight groups of the address expressed separately in
hexadecimal and separated by colons. Possible values are
0000:0000:0000:0000:0000:0000:0000:0000 to FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF. A
default value is entered if the DHCP service is available.
AES (advanced encryption standard) encryption
This option enables / disables AES encryption. The AES specifies a FIPS approved
cryptographic algorithm that protects electronic data. The AES algorithm is a symmetric block
cipher that can encrypt and decrypt information.
AES key size
This option defines the cryptographic key bit size that is used for encryption. Possible values
are:
–
128 bits
–
192 bits
–
256 bits
AES key string
This option defines the encryption key in hexadecimals. Possible values are 32 or 48 or 64
hexadecimals characters:
–
For a 128-bit key length, enter 32 hexadecimal characters.
–
For a 192-bit key length, enter 48 hexadecimal characters.
–
For a 256-bit key length, enter 64 hexadecimal characters.
Configure B450?
This option defines whether or not you are using a B450 module.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
50
en | Settings
AMAX panel
SIM PIN
This option defines the SIM PIN. This option is only applicable if the SIM card uses a PIN for
security.
The SIM PIN is hidden on the display and appears as asterisks (********) when entered. If an
invalid SIM PIN is entered, an event is logged in history. A report is sent only if the report
function is enabled. If no SIM PIN is required, you can leave the field blank.
Possible values are numbers. The length must be 4 to 8 characters.
Network access point name
This option defines the IP address for the network access point. Possible values are ASCII
printable characters. The maximum length is 99 characters. The entry is case sensitive.
Network point user name
This option defines the user name for the network access point. Possible values are ASCII
printable characters. The maximum length is 30 characters. The entry is case sensitive.
Network access point password
This option defines the password required to access the network access point. Possible values
are ASCII printable characters. The maximum length is 30 characters. The entry is case
sensitive.
6.1.6
Remote access
The AMAX panel supports remote programming via USB, telephone, or IP network using the
remote programming software A-Link Plus. The following options can be performed:
–
Setting the date and time
–
Uploading / downloading programming parameters
–
Remote arming / disarming of each area
–
Enabling / disabling the alarm siren of each area
–
Enabling / disabling each output
–
Maintenance
–
Domestic testing
–
Communication testing
–
Downloading voice files
–
Viewing history events
Remote access armed
This option enables / disables the remote access while the system is armed.
Remote PSTN access
This option enables / disables the remote access for telephone.
Remote IP access
This option enables / disables the remote access for programming. If this function is disabled,
the system can not be programmed via an IP network anymore.
RPC access code
In this option the RPC access code can be entered. The maximum length is ten digits.
6.1.7
Remote PC
IP Address
RPC IP address is a fixed IP address for remote programming software.
Port number
RPC port number is the port number for remote programming.
How to program an IP address and port
1. Program an IP address with 17 digits: digits 1 - 12 for the IP address and 13 - 17 for the
port.
2.
2016.05 | 08 | F.01U.309.277
Use no punctuation in the IP address.
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Settings | en
3.
51
If any unit of the IP address has less than 3 digits, use 0 to fulfill the data in the higher
bits.
4.
The remaining 5 digits program the port. Port number ranges from 0-65535.
5.
If a port number has less than 5 digits, use 0 to fulfill the data.
Example
4 To program the IP address “10.16.1.222:80”, enter the following sequence into the
correspondent address:
[0 1 0 0 1 6 0 0 1 2 2 2 0 0 0 8 0]
DHCP Update / RPC poll Time Interval
DHCP update / RPC poll time is the interval at which AMAX panel connects to the RPC
(Remote Programming PC).
The AMAX panel send UDP data packets to the RPC according to the DHCP Update Time
Interval setting (0=disabled 1-15h Interval), when the panel is reset and when call back is
finished.
RPC gets the Subscriber ID, IP address and port from the UDP data packets (IP No. and Port
is parsed from UDP data packet).
RPC with running RPS (Remote Programming Software = A-Link Plus) saves the received UDP
data packet information into its own RAM, the information is lost after RPS is closed.
When a connection is started and the IP address set in the customer information doesn’t
match with the IP Address from the RAM, the A-Link Plus opens a window to ask if the new IP
Address and Port should be used.
When RPS is opened, a connection can only be established when the IP address and port
number of the AMAX panel have not changed, after RPS received previous data.
If the IP address has changed RPC with running RPS must wait for the next UDP Data package
send from the Panel. When the connection is established, the AMAX panel sends a polling
telegram of 25 bytes.
6.1.8
Call back and domestic call
Call back telephone number
This address stores the telephone number to call when upload / download is requested or the
user enters his code + [5] [7] and presses [#] to initiate a modem call from the AMAX panel to
establish a communication link with the remote computer. The computer must be running
remote programming software A-Link Plus and must be set to waiting for an incoming call. The
call back telephone number is also necessary if remote connect with call back verification is
required.
Domestic call
Four recordable voice messages for four dialing telephone numbers are supported. Each of the
four recordable voice messages can take up to 9 seconds. The voice messages are recorded
with the tool “Rec.exe” that comes with A-Link Plus and are transferred via A-Link Plus to the
AMAX panel. They can only be transferred via USB or network connection. The supported
format of the voice message files is the following:
–
For firmware version up to 1.4: .wav
–
For firmware version 1.5 and higher: .va3
When the AMAX panel is activated into zone tamper / zone alarm, the programmed telephone
number is dialed and the recorded voice message is played.
All alarm events only need one report / acknowledgement.
The transmission sequence is repeated until the AMAX panel receives an acknowledgement
tone.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
52
en | Settings
AMAX panel
The AMAX panel automatically hangs up after about 45 seconds if it cannot detect the
acknowledgement tone and redial later.
The user presses any key on the telephone between two acknowledgement tones to confirm
the alarming.
The acknowledgement tone is the DTMF signal sent by the remote user with any key ([0] - [9]
or [*] or [#]).
If the AMAX panel received the acknowledgement from the user, it will send a 2 seconds long
confirmation beep as an acknowledge tone and hang up the line.
6.1.9
Ring times
Ring Count
This function defines the number of rings before the AMAX panel answers an incoming call. It
is necessary to enable remote arming and remote upload/download to use this function.
The following values are selectable:
–
0 = The panel does not answer any incoming calls.
–
1 – 13 = Number of rings until the control panel answers.
–
14 = The control panel is called, the phone is allowed to ring only twice and hangs up.
After 8 to 45 seconds the control panel is called again and answers to the first ring. If the
control panel is called before 8 seconds have passed, it does not answer the call.
–
15 = The control panel is called, the phone is allowed to ring only four times and hangs
up. Within 45 seconds the control panel is called again, it answers to the first ring and the
connection is established. This prevents the answering machine or fax machine from
answering the call.
6.2
Users and codes
The AMAX system provides two types of access codes, the installer codes and user codes.
Each of them allows specific access and operation of the AMAX panel functions.
6.2.1
User code
The default users are master user 1 (code: [2580]) and master user 2 (code: [2581]). These
codes should be changed to individual codes. If a new user is assigned, an individual user
code is assigned to this user.
Notice!
Identical codes are not allowed. User codes are not permitted to be the same as the installer
code.
User Code Priority
User codes can differ in permission levels. Each user code is assigned to a permission level.
Code Permission Level
User Type
00
Master User 1
01
Master User 2
02
Super User
03
Basic User
04
Arming User
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Settings | en
05
Duress User
06 -15
No Priority
53
Please refer to Installer code, page 53 for a description of the user permission levels.
User Code in Area
This option has a different function dependant on which user type has been selected above.
–
For Super User, Basic User, Arming User and Duress User:
For each of these user types any area can be assigned individually. Keyfobs are
automatically assigned to the selected areas as well.
For example: If 01 and 02 is selected in this option, area 01 and 02 is assigned. Keyfobs
are also assigned to area 01 and 02.
–
For Master User 1 and 2:
For master users all areas are automatically assigned although they are displayed as
unassigned on the keypad. Areas can not be unassigned. Changes in this option only
apply to keyfobs.
For example: If 01 and 02 is selected in this option, all areas are assigned and keyfobs are
assigned to area 01 and 02.
User Macro Authorizing
For each user, up to three recordable macros can be assigned.
Keyfob ID
Keyfobs are designed for arming and disarming the system remotely, trigger a panic alarm, or
for additional control functionality. For each user, one keyfob ID can be assigned
To operate the buttons, press and hold either button for at least one sec in order to use the
desired feature.
The AMAX panel identifies keyfob users by device RFID. AMAX Keypad programming supports
entering RFID automatically for Radion devices.
4
When the keyfob RFID is asked for, press [*] for 3s to toggle between AUTO and
MANUAL mode.
When MANUAL is selected, enter the 9-digit RFID manually.
When AUTO is selected, trigger the RF device and the RFID is entered automatically.
Keyfob Button 3
For the keyfob button 3 the following settings can be selected:
0 – not used
1 – output control
2 – STAY arm
6.2.2
Installer code
The installer code is designed to program the AMAX panel. In addition, the installer code is
used for some code commands.
The default installer code is 1234. The default user code 1 is 2580. The default user code 2 is
2581. These codes should be changed to an individual code.
Notice!
Identical codes are not allowed. User codes are not permitted to be the same as the installer
code.
Quick keypad operations
The following table shows an overview of the quick keypad operations and the corresponding
user permissions of user codes and installer codes.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
54
en | Settings
AMAX panel
Function
Command
D A B S M M I
Default code for user 1 = 2580
1
2
N
Default code for user 2 = 2581
Arm/Disarm
AWAY Arm
[code] + [#] / [#] for 3 sec. (quick arm)
√
√
√
√
√
√
√
AWAY Arm All Areas (only
[code] + [0] [0] + [#]
√
√
√
√
√
√
√
√
√
√
on master keypad)
Direct AWAY Arm (only on
[code] + [2-digit area no.] + [#]
master keypad
STAY Arm
[code] + [*] / [*] for 3 sec. (quick arm)
√
√
√
√
√
√
√
STAY Arm All Areas (only
[code] + [0] [0] + [*]
√
√
√
√
√
√
√
[code] + [2-digit area no.] + [*]
√
√
√
√
√
√
√
[code] + [#]
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
on master keypad)
Direct STAY Arm (only on
master keypad
Disarm
Disarm One Area (only on a [code] + [2-digit area no.] + [#]
master keypad)
Disarm All Areas (only on
[code] + [#]
master keypad)
Display
Display Info (Fault/Tamper
[code] + [2] [1] + [#]
Analysis)
Bypass/Isolate
Bypass/Unbypass Zone
Text keypad: [code] + [3] [1] + [#] + [1
√
√
√
√
√
√
√
√
√
√
√
√
√
√
or 2-digit zone no.] + [#]
LED/LCD keypad: [code] + [3] [1] + [1 or
2-digit zone no.] + [*] + [#]
[code] + [3] [1] + [#] (cancel LED
keypad)
Bypass Fault/Tamper
[code] + [3] [4] + [#]
Inquire Bypass
[code] + [3] [3] + [#]
√
√
√
Isolate Zone
[code] + [3] [5] + [#]
√
√
√
Inquire Isolate
[code] + [3] [6] + [#]
√
√
√
√
√
√
Reset
Reset Fault/Tamper (In
[code] + [6] + [#]
√
some country versions only
the installer can reset a
tamper alarm)
Macros
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Settings | en
Function
Command
55
D A B S M M I
Default code for user 1 = 2580
1
2
N
√
√
√
√
√
√
√
√
√
√
√
√
Default code for user 2 = 2581
Record Macro 1
[code] + [8] [1] + [#] + sequence to be
recorded + [#] for 3 sec.
Record Macro 2
[code] + [8] [2] + [#] + sequence to be
recorded + [#] for 3 sec.
Record Macro 3
[code] + [8] [3] + [#] + sequence to be
recorded + [#] for 3 sec.
Play Macro 1
[code] + long press [1] / [1] for 3 sec.
*
*
*
*
*
*
√
*
*
*
*
*
*
√
*
*
*
*
*
*
√
(quick macro)
Play Macro 2
[code] + long press [2] / [2] for 3 sec.
(quick macro)
Play Macro 3
[code] + long press [3] / [3] for 3 sec.
(quick macro)
Alarm commands
Keypad Emergency Alarm
long press [1] and [3] or [*] and [#]
√
√
√
√
√
√
√
Keypad Fire
long press [4] and [6]
√
√
√
√
√
√
√
Keypad Medical Alarm
long press [7] and [9]
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
Other Commands
Switch to Master Keypad
[code] + [0] [0] [0] + [#] (only on text
keypad)
Switch to Area 01-16
[code] + [0] [2-digit area no.] + [#] (only
on text keypad)
Display all Event Log
[code] + [2] [2] + [#] (only on text
keypad)
Display EN Event Log
[code] + [2] [3] + [#] (only on text
keypad)
Display Dialer Event Log
[code] + [2] [4] + [#] (only on text
keypad)
Siren Test
[code] + [4] [1] + [#]
√
√
√
√
Communication Test
[code] + [4] [2] + [#]
√
√
√
√
Walk Test
[code] + [4] [3] + [#]
√
√
√
√
Change Date/Time
[code] + [5] [1] + [#]
√
√
√
Daylight Saving Time (+1h) [code] + [5] [2] + [#]
√
√
√
√
Daylight Saving Time (-1h)
[code] + [5] [3] + [#]
√
√
√
√
Add/Change User Code
[code] + [5] [4] + [#]
√
√
√
Change Individual Code
[code] + [5] [5] + [#]
√
√
√
√
Installation Manual
2016.05 | 08 | F.01U.309.277
Bosch Sicherheitssysteme GmbH
√
√
√
56
en | Settings
AMAX panel
Function
Command
D A B S M M I
Default code for user 1 = 2580
1
2
N
Default code for user 2 = 2581
Call Back
[code] + [5] [7] + [#]
√
√
√
√
Change Language
[code] + [5] [8] + [#] + [2-digit no. for
√
√
√
√
√
√
√
√
available languages] + [#]
01=EN; 02=DE; 03=ES; 04=FR ; 05=PT;
06=PL; 07=NL; 08=SE; 09=TR
Installer Access
[code] + [7] [1] + [#] (enable)
[code] + [7] [2] + [#] (disable)
System Reset
[code] + [9] [9] [8] [9] + [#]
√
√
D = Duress User
A = Arming User
B = Basic User
S = Super User
M1 = Master User 1
M2 = Master User 2
IN = Installer
* This function can be enabled/disabled individually for every user.
Quick keypad configurations
The following table shows an overview of the quick keypad configurations and the
corresponding user permissions of user codes and installer codes.
Function
Command
D A B S M M I
Default code for installer = 1234
1
2
N
Default code for user 1 = 2580
Default code for user 2 = 2581
Change Dom. Phone No. 1
[code] + [5] [6] + [#] + [ _ _ _ _ _ _ ] + [# ]
√
(LED keypad )
Change Dom. Phone No. 2
[code] + [5] [6] + [#] [#] + [ _ _ _ _ _ _ ] +
√
[# ] (LED keypad )
Change Dom. Phone No. 3
[code] + [5] [6] + [#] [#] [#] + [ _ _ _ _ _
√
_ ] + [# ] (LED keypad )
Change Dom. Phone No. 4
[code] + [5] [6] + [#] [#] [#] [#] + [ _ _ _ _
√
_ _ ] + [# ] (LED keypad )
Change Dom. Phone No.
[code] + [5] [6] + [#] + [ _ ] +[#] +[ _ _ _ _
1-4
_ _ ] + [# ] (text keypad )
√
Service Mode
[code] + [7] [3] + [#] (enable/disable)
√
Programming Mode
[code] + [9] [5] [8] + [#]
√
Commands only for address programming mode
Exit Programming Mode
[9] [5] [9] + [#]
√
without saving
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Settings | en
Function
Command
57
D A B S M M I
Default code for installer = 1234
1
2
N
Default code for user 1 = 2580
Default code for user 2 = 2581
Exit Programming Mode
[9] [6] [0] + [#]
√
[9] [6] [1] + [#]
√
Copy Control Panel Data to [9] [6] [2] + [#]
√
with saving
Set Factory Default
Programming Key
Copy Programming Key
[9] [6] [3] + [#]
√
[9] [9] [9] + [#]
√
Data to Control Panel
Display Firmware Version
D = Duress User
A = Arming User
B = Basic User
S = Super User
M1 = Master User 1
M2 = Master User 2
IN = Installer
Notice!
The installer commands can be used only when all areas of the system are in disarming status
with no alarm activated and when the installer access is enabled by the user.
6.2.3
Code length
The length of the codes can be set in a range from 4 to 6 digits.
6.2.4
Code permissions
Tamper reset by user
This option defines whether tampers can be reset with a user code. If this option is disabled,
tamper resets can only be performed with the installer code.
Arm / disarm installer
This option defines whether the arm / disarm function can be performed with the installer
code. If this option is disabled, the arm / disarm function can not be performed with the
installer code.
Date / time master user
This option defines whether the date / time function can be performed with a master user
code. If this option is disabled, the date / time can not be set with a master user code.
6.2.5
Force code change
This option defines whether the installer code and master user 1/2 code has to be changed
during programming. If this option is enabled, programming can only be finished if the installer
code is changed. For an EN compliant operation, it is necessary to enable this option.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
58
en | Settings
6.2.6
AMAX panel
Macro configuration
Macros are used to assign complicated or often used button sequences on the keypad to one
button to simplify the operation of the system. Therefore, a button sequences is entered on
the keypad, recorded and assigned to a macro. If this macro is played, the recorded button
sequence will be executed.
It is possible to record up to three macros.
Input Macro Number
In this option the number of the macro to be configured is selected. (Possible numbers are 1,
2 and 3.)
Macro without Code
This option enables/disables the quick play function of the macro. If this function is enabled,
the user can press the number of the macro for three seconds to execute the macro playing
function without entering a code.
Macro Recording Timeout
This option defines the timeout of the macro recording process. (Possible values are 01 – 99
seconds.) The timeout defines the time after which the macro recording process is cancelled
due to inactivity of the user.
Play Pause Time
This option defines the speed of the macro playing process. If a user wants to observe the
macro playing process more closely, it can be adjusted to display the single operations longer.
The default setting is 03=300ms and can be adjusted to 01=100ms, 02=200ms and so on.
Level 1 access
This option enables/disables the code inside a macro. This function is relevant only if the
macro without code function is disabled.
The possible selections are:
–
1-enable
–
0-disable
If this function is enabled, a code will be recorded during the macro recording process and
will be executed during the macro playing process. This means that a user switch is possible
when the macro playing function is executed.
If this function is disabled, there will be no code recorded during the macro recording process
and the operation assigned to the macro will be executed without a code. This means that
there is no user switch possible in the macro playing function and that the user who is
executing the macro playing function is also executing the operation assigned to the macro.
6.2.7
Code reporting
The following codes are reported when an alarm occurs:
Installer
Report = 0
User 1 - 250
Report = 1 - 250
A-Link Plus
Report = 251
Phone arm
Report = 252
Single-button arm / disarm
Report = 253
Key switch arm / disarm
Report = 254
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Settings | en
6.3
Zones
6.3.1
Add / delete zone
59
When adding or changing a zone, it is required to select the area, the zone functions and the
module of the zone source, based on zone numbers.
When the zone is specified as “0”, i.e. the zone is not used; any address set on the zone
function and module selection is invalid.
Zone module
The AMAX panel supports onboard zones, keypad zones and DX2010 zones and RF zones. For
each zone number a certain range of selectable modules is defined.
Zone function
In this option, the zone function can be selected. Up to 15 configurations for zone functions
can be defined under the option zone function.
When selecting the zone function via text keypad, the zone type that has been selected for the
zone function of each zone is displayed.
Zone in area
Each zone is assigned to an area. This assignment influences the way how zones are indicated
on keypads.
4
For more information, please refer to Zone indication keypad and event log, page 74.
Zone Name
This option is used to name zones.
4
Use the numbers on the text keypad as an alphabetical input.
Number on the
Alphabetical input when number is pressed consecutively
text keypad
1
.,'?!"1-()@/:_¹²³©®º«»µ¶
2
abc2æåäàáâãçćč
3
def3èéêëðę
4
ghi4ìíîïğ
5
jkl5£
6
mno6öøòóôõñ
7
pqrs7ßšśş
8
tuv8ùúûüűţ
9
wxyz9ýþźżžŸ
*
Switches between small letters and capital letters
0
space 0 ; + & % * = < > £ € $ ¥¤ [ ]{}\ ~ ^ ` ¿ ¡ § # |
RF zones
AMAX 3000 / 3000 BE / 4000 identifies RF zones by Zone RFID. AMAX Keypad programming
supports entering RFID automatically for Radion devices.
How to enter the RFID on the keypad
1. When the zone RFID is asked, press * button for 3 second toggles between AUTO and
MANUAL mode.
2.
When MANUAL is selected, enter 9 – digit RFID using pin keys.
When AUTO is selected, trigger RF device in order to enter RFID automatically.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
60
en | Settings
AMAX panel
Hardwired input zones
On-board inputs:
The AMAX panel provides onboard hard-wired inputs. An additional input is provided for the
enclosure tamper.
On-board zone response time:
The AMAX panel supports different response times for the onboard zones. The response time
value range is 000.0-999.9 seconds.
On-board zone EOL
Single EOL: If the zone tamper function is not selected, each zone uses a single 2.2 kilo ohm
EOL. The panel can detect the zone as short, normal or open.
Loop resistance (ohm)
Min
Type
0
1650
2200
2970
Zone status
Max
1430
triggered
2750
normal
∞
triggered
The detectors (sensors) will be connected between zone and COM terminal through EOL
series (open triggered) or parallel connection (short triggered).
COM
Zone
The detectors (sensors) will be connected between zone and COM terminal through EOL
series connection (open triggered) or EOL parallel connection (short triggered).
COM
Zone
The panel sets the short / open as activate when connecting with single EOL.
The valid zone number is 1-8 for AMAX 2100 / 3000 / 3000 BE, 1-16 for AMAX 4000.
Dual EOL: If the tamper supervision is set, we only can use the NC contact point. The EOL
status is:
Zone Status
Loop resistance (ohm)
Min
Type
Max
o
1430
tamper
1650
2200
2750
normal
2970
4400
4950
triggered
∞
tamper
5220
Using one 2.2 kilo resistor as EOL of the tamper zone, which works together with the zone
EOL 2.2 kilo.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Settings | en
COM
61
1
2
Z3
BBBBB7DPSHU6ZLWFK
BBBBB=RQH6ZLWFK
NC (normally close): If the zone option is set to “NC”, an alarm occurs when the zone is
opened. When the zone is closed, the system is in normal mode.
NO (normally open): If the zone option is set to “NO”, an alarm occurs when the zone is
closed. When the zone is opened, the system is in normal mode.
On-board tamper input
A separate input is provided for enclosure tamper. The response time of the tamper input can
be programmed individually. The response time value range is 000.0-999.9 seconds.
6.3.2
Zone function settings
Zone type
The following zone types can be selected for each zone function.
Zone function option
Zone type
Bosch Sicherheitssysteme GmbH
Description
00
Not used
01
Instant
02
Interior instant
03
Delay 1
04
Interior delay 1
05
Delay 1 exit
06
Interior delay 1 exit
07
Delay 2
08
Interior delay 2
09
Delay 2 exit
10
Interior delay 2 exit
11
Follower
12
Interior follower
13
24-hour
14
Key AWAY toggle
15
Key AWAY on/off
16
Key STAY toggle
17
Key STAY on/off
18
24-hour panic
19
24-hour fire
Installation Manual
2016.05 | 08 | F.01U.309.277
62
en | Settings
AMAX panel
20
24-hour fire with verification*
21
Tamper
22
Bold contact
23
External fault
24
Technical alarm
25
Reset
26
Instant report
* Only possible for AMAX 4000 zone 1
00 - Not used
If a zone is not used, program the zone type location to 0. An EOL resistor is not required if
this zone type is not used. This zone type never activates the sirens or the dialer.
01 - Instant
The instant zone type performs as described below:
1.
2.
Disarm:
–
Zone normal - no alarm / no report
–
Zone triggered - no alarm / no report
AWAY Arm:
–
Zone normal - no alarm / no report
–
Zone triggered - alarm / report
–
(Zone triggered during exit time no alarm / no report)
–
(Zone triggered during entry time alarm / report is delayed for 30 second or entry
time is expired, when system is disarmed before, no report)
3.
STAY Arm:
–
Zone normal - no alarm / no report
–
Zone triggered - alarm / report
–
(Zone triggered during exit time no alarm / no report)
–
(Zone triggered during entry time alarm / report is delayed for 30 second / entry time
is expired, when system is disarmed before, no report) When zone is triggered, not
bypassed and system is forced to arm, a zone fault report is sent.
–
When the system is disarmed and zone is not restored before, a Zone fault restore
report is sent.
02 - Interior instant
The interior instant zone type performs as described below:
1.
Disarm:
–
2.
AWAY Arm:
–
3.
same as the instant zone disarm status
same as the instant zone AWAY arm status
STAY Arm:
–
When zone is triggered, not bypassed and system is forced to arm, a zone fault
report is send.
–
When system is disarmed and zone is not restored before, a zone fault restore report
is sent.
–
2016.05 | 08 | F.01U.309.277
This zone will be ignored and performed as disarm.
Installation Manual
Bosch Sicherheitssysteme GmbH
Settings | en
AMAX panel
4
63
Refer to Keypad Indicators to see how the zone is displayed during exit time.
03 - Delay 1
The delay 1 zone type performs as described below:
1.
Disarm: same as instant zone disarm status
2.
AWAY Arm:
–
Zone normal - no alarm / no report
–
Zone triggered - entry time starts - no alarm / no report
–
Disarming during entry time - no alarm / no report
–
Zone triggered - during exit time - no alarm / no report
–
Zone triggered - during entry time - no alarm / no report
–
Zone triggered - entry time is expired - alarm / report
–
(report is delayed for a specified time (default: 30s; value range: 00-99), when
system is disarmed before, no report)
3.
STAY Arm: same as AWAY arm performance.
–
–
First delay zone will start the entry time; all other delay zones will follow.
When system is disarmed and zone is not restored before, a zone restore report is
sent.
04 - Interior delay 1
The interior delay 1 zone type performs as described below:
1.
Disarm: same as the instant zone disarm status
2.
AWAY Arm: same as the delay zone AWAY arm status
3.
STAY Arm:
–
4
This zone will be ignored and performed as disarm.
Refer to Keypad Indicators to see how the zone is displayed during exit time.
05 - Delay 1 exit
The delay 1 exit zone type performs as described below:
1.
DISARM: same as instant zone disarm status
2.
AWAY Arm:
–
Zone normal - no alarm / no report
–
Zone triggered - entry time starts - no alarm / no report
–
Disarming during entry time - no alarm / no report
–
Zone triggered - during exit time - no alarm / no report / abbreviates remaining time
for exit to 5 seconds
–
Zone triggered - during entry time - no alarm / no report
–
Zone triggered - entry time is expired - alarm / report (report is delayed for 30
second, when system is disarmed before, no report)
3.
STAY Arm: same as AWAY arm performance
–
First delay zone will start the entry time; all other delay zones will follow.
–
When system is disarmed and zone is not restored before, a zone restore report is
sent.
06 - Interior delay 1 exit
The Interior delay 1 exit zone type performs as described below:
1.
Disarm: same as the instant zone disarm status
2.
AWAY Arm: same as the delay exit zone AWAY arm status
3.
STAY Arm:
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
64
en | Settings
AMAX panel
–
4
This zone will be ignored and performed as disarm.
Refer to Keypad Indicators to see how the zone is displayed during exit time.
07 - Delay 2
The delay 2 zone type performs as described below:
1.
Disarm: same as instant zone disarm status
2.
AWAY Arm:
–
Zone normal - no alarm / no report
–
Zone triggered - entry time starts - no alarm / no report
–
Disarming during entry time - no alarm / no report
–
Zone triggered - during exit time - no alarm / no report
–
Zone triggered - during entry time - no alarm / no report
–
Zone triggered - entry time is expired - alarm / report
–
(report is delayed for a specified time (default: 30s; value range: 00-99), when
system is disarmed before, no report)
3.
STAY Arm: same as AWAY arm performance.
–
First delay zone will start the entry time; all other delay zones will follow.
–
When system is disarmed and zone is not restored before, a zone restore report is
sent.
08 - Interior delay 2
The interior delay 2 zone type performs as described below:
1.
Disarm: same as the instant zone disarm status
2.
AWAY Arm: same as the delay zone AWAY arm status
3.
STAY Arm:
–
4
This zone will be ignored and performed as disarm.
Refer to Keypad Indicators to see how the zone is displayed during exit time.
09 - Delay 2 exit
The delay 2 exit zone type performs as described below:
1.
DISARM: same as instant zone disarm status
2.
AWAY Arm:
–
Zone normal - no alarm / no report
–
Zone triggered - entry time starts - no alarm / no report
–
Disarming during entry time - no alarm / no report
–
Zone triggered - during exit time - no alarm / no report / abbreviates remaining time
for exit to 5 seconds
–
Zone triggered - during entry time - no alarm / no report
–
Zone triggered - entry time is expired - alarm / report (report is delayed for 30
second, when system is disarmed before, no report)
3.
STAY Arm: same as AWAY arm performance
–
First delay zone will start the entry time; all other delay zones will follow.
–
When system is disarmed and zone is not restored before, a zone restore report is
sent.
10 - Interior delay 2 exit
The Interior delay 2 exit zone type performs as described below:
1.
Disarm: same as the instant zone disarm status
2.
AWAY Arm: same as the delay exit zone AWAY arm status
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
Settings | en
AMAX panel
3.
STAY Arm:
–
4
65
This zone will be ignored and performed as disarm.
Refer to Keypad Indicators to see how the zone is displayed during exit time.
11 - Follower
The follower zone type performs as described below:
1.
Disarm:
2.
AWAY Arm:
–
same as the instant zone disarm status
–
Zone normal - no alarm / no report
–
Zone triggered - alarm / report
–
Zone triggered - during exit time - no alarm / no report
–
Zone triggered - during entry time - no alarm / no report
–
The remaining delay time is handed over from the delay zone to the follower zone.
–
The follower zone performance as the same as a delay zone.
–
If there are two or more zones programmed as delay zones and both are triggered,
the follower zone will follow the first triggered delay zone.
3.
STAY Arm: same as the delay zone.
12 - Interior follower
The interior follower zone type performs as described below:
1.
Disarm: same as the instant zone disarm status
2.
AWAY Arm: same as the follower zone AWAY arm status
3.
STAY Arm:
–
4
This zone will be ignored and performed as disarm.
Refer to Keypad Indicators to see how the zone is displayed during exit time.
13 - 24 hour
The 24-hour zone type performs as described below:
1.
2.
3.
Disarm:
–
Zone normal - no alarm / no report
–
Zone triggered - alarm / report
AWAY Arm:
–
Zone normal - no alarm / no report
–
Zone triggered - alarm / report
–
Zone triggered - during exit time - alarm / report
–
Zone triggered - during entry time - alarm / report
STAY Arm: same as AWAY arm performance.
–
A 24 - hour zone does not send a restore report until the zone is restored.
14 - Key AWAY toggle
The key switch AWAY toggle zone type performs as described below:
1.
2.
3.
Disarm:
–
Zone normal - no action
–
Zone triggered - activate AWAY arm / report
AWAY Arm:
–
Zone normal - no action
–
Zone triggered - activate disarm / report
STAY Arm: same as AWAY arm performance
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
66
en | Settings
AMAX panel
This zone will ignore all other programming items, such as bypass, forcing arm.
When the system is armed in this mode, the keypad activates two beeps and report sent is by
user code 254.
15 - Key AWAY on/off
The key switch AWAY on / off zone type performs as described below:
1.
2.
3.
Disarm:
–
Zone normal - no action
–
Zone triggered - activate AWAY arm / report
AWAY Arm:
–
Zone normal - activate disarm / report
–
Zone triggered - no action
STAY Arm: same as AWAY arm performance
Wiring diagram for key-switch zone: short for arm. The momentary time is capable of lasting
Minimum 300ms.
Wiring diagram for key-switch zone: open for arm. The momentary time is capable of lasting
Minimum 300ms.
When the key-switch operates the arm/disarm, the keypad sounds two beeps and report sent
to the system by user code 254.
Notice!
When the key-switch operates the arm/disarm successfully, the siren sounds short to indicate
it.
16 - Key STAY toggle
The key switch momentary STAY zone type performs as described below:
1.
2.
3.
Disarm:
–
Zone normal - no action
–
Zone triggered - activate STAY arm / report
AWAY Arm:
–
Zone normal - no action
–
Zone triggered - activate disarm / report
STAY Arm: same as AWAY arm performance
This zone will ignore all other programming items, such as bypass, forcing arm.
When the system is armed in this mode, the keypad activates two beeps and report sent is by
user code 254.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Settings | en
67
17 - Key STAY on/off
The key switch on/off STAY zone type performs as described below:
1.
2.
3.
Disarm:
–
Zone normal - no action
–
Zone triggered - activate STAY arm / report
AWAY Arm:
–
Zone normal - activate disarm / report
–
Zone triggered - no action
STAY Arm: same as AWAY arm performance
When the key-switch operates the arm / disarm, the keypad sounds two beeps and report sent
to the system by User Code 254.
Notice!
When the key-switch operates the arm/disarm successfully, the siren sounds short to indicate
it.
18 - 24-Hour panic
The 24-hour panic zone type performs as described below:
1.
2.
3.
Disarm:
–
Zone normal - no alarm / no report
–
Zone triggered - silent alarm / report
AWAY Arm:
–
Zone normal - no alarm / no report
–
Zone triggered - silent alarm / report
–
Zone triggered - during exit time - silent alarm / report
–
Zone triggered - during entry time - silent alarm / report
STAY Arm: same as AWAY arm performance
–
A 24-hour panic zone has no restore report until the zone is restored.
19 - 24 Hour fire
The 24-hour fire zone type performs as described below:
1.
2.
3.
Disarm:
–
Zone normal - no alarm / no report
–
Zone triggered - alarm / report
AWAY Arm:
–
Zone normal - no alarm / no report
–
Zone triggered - alarm / report
–
Zone triggered - during exit time - alarm / report
–
Zone triggered - during entry time - alarm / report
STAY Arm: same as AWAY arm performance
–
A fire zone does not send a restore report until the zone is restored.
20 - 24-hour fire with verification
(Only possible for AMAX 4000 / AMAX 3000 BE zone 1)
The 24-hour fire with verification zone type performs as described below:
1.
Disarm:
–
Bosch Sicherheitssysteme GmbH
Zone normal - no alarm / no report
Installation Manual
2016.05 | 08 | F.01U.309.277
68
en | Settings
AMAX panel
–
Zone triggered: After the first alarm, the AMAX panel performs a fire verification reset
(10 seconds) and then waits a period up to two minutes for a second alarm. If a
second alarm occurs within this period, the AMAX panel indicates a fire alarm.
Otherwise, the AMAX panel resets back to its normal condition. At the end of the two
minute period an unverified fire alarm is logged and reported. A fire zone does not
send a restore report until the zone is restored.
2.
AWAY arm: same as disarm performance
3.
STAY arm: same as disarm performance
21 - Tamper
The tamper zone type performs as described below:
1.
2.
3.
Disarm:
–
Zone normal - no alarm / no report
–
Zone triggered - alarm / report
AWAY Arm:
–
Zone normal - no alarm / no report
–
Zone triggered - alarm / report
–
Zone triggered - during exit time - alarm / report
–
Zone triggered - during entry time - alarm / report
STAY Arm: same as AWAY arm performance
–
A tamper zone does not send a restore report until the zone is restored.
22 - Bolt contact
The bolt-contact zone type performs as described below:
1.
2.
3.
Disarm:
–
Zone normal - no alarm / no report
–
Zone triggered - no alarm / no report
AWAY Arm:
–
Zone normal - no alarm / no report
–
Zone triggered - no alarm / no report
–
Zone triggered - during exit time - no alarm / no report
–
Zone triggered - during entry time - no alarm / no report
STAY Arm: same as AWAY Arm performance.
–
This zone is mainly for prevention of arming (to ensure exit/entry door is locked
before arming the system and no alarm occurs when entering the premise through
the entry/exit door).
23 - External fault
The external fault zone type performs as described below:
1.
2.
3.
Disarm:
–
Zone normal - no alarm / no report
–
Zone triggered - fault / report
AWAY Arm:
–
Zone normal - no alarm / no report
–
Zone triggered - alarm / report
–
Zone triggered - during exit time - fault / report
–
Zone triggered - during entry time - fault / report
STAY Arm: same as AWAY Arm performance
–
2016.05 | 08 | F.01U.309.277
The restore report will be sent when the zone is restored.
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Settings | en
69
24 - Technical alarm
The technical alarm zone type performs as described below:
1.
2.
3.
Disarm:
–
Zone normal - no alarm / no report
–
Zone triggered - alarm / report
AWAY Arm:
–
Zone normal - no alarm / no report
–
Zone triggered - alarm / report
–
Zone triggered - during exit time - alarm / report
–
Zone triggered - during entry time - alarm / report
STAY Arm: same as AWAY arm performance.
–
A technical zone does not send a restore report until the zone is restored.
25 - Reset
The reset zone type performs as described below:
1.
2.
Disarm:
–
Zone normal - no alarm / no report
–
Zone triggered - performs system reset / no report
AWAY Arm:
–
3.
Zone normal - no alarm / no report
STAY Arm: same as AWAY arm performance
26 - Instant report
The instant report zone type performs as described below:
1.
Disarm:
–
Zone normal - no action
–
Zone triggered - report
2.
AWAY Arm: same as disarm performance
3.
STAY Arm: same as disarm performance
Overview of the zone function options
Description
Zone function option
Force arm / bypass
Silent alarm / Chime
mode
Zone pulse count
Bosch Sicherheitssysteme GmbH
0
Disabled
1
Force arm
2
Bypass
3
All
0
Disabled
1
Silent alarm
2
Chime mode
3
All
0
Disabled
1-9
1-9 pulses
Installation Manual
2016.05 | 08 | F.01U.309.277
70
en | Settings
AMAX panel
Zone lockout
Zone EOL
Zone status report
Unverified alarm
report / cross zone
Zone domestic call
2016.05 | 08 | F.01U.309.277
0
Disabled
1
1 times alarm lockout
2
3 times alarm lockout
3
6 times alarm lockout
4
Alarm duration
0
EOL 2,2k
1
DEOL 2,2k / 2,2k
2
Reserved
3
NC
4
NO
0
No report required
1
Receiver 1
2
Receiver 2
3
Receiver 3
4
Receiver 4
5
Receiver 1, 2, 3, and 4
6
Receiver 1 (2, 3, and 4 for backup)
7
Receiver 1 (2 for backup) and receiver 3 (4 for backup)
8
Receiver 1, 2
9
Receiver 1 (2 for backup)
10
Receiver 3, 4
11
Receiver 3 (4 for backup)
0
Disabled
1
Unverified alarm report
2
Cross zone
3
All
Follow “alarm report” option's logic. range 0-11
0
No reports allowed
1
Report to destination 1
2
Report to destination 2
3
Report to destination 3
4
Report to destination 4
5
Report to destination 1 ,2, 3, 4
6
Report to destination 1 (2, 3, and 4 for backup)
Installation Manual
Bosch Sicherheitssysteme GmbH
Settings | en
AMAX panel
7
71
Report to destination 1 (2 for backup) and 3 (4 for
backup)
Zone alarm on keypad
Trouble domestic
8
Report to destination 1, 2
9
Report to destination 1 (2 for backup)
10
Report to destination 3, 4
11
Report to destination 3 (4 for backup)
0
Disabled
1
Enabled
0
Disabled
1
Enabled
Detection time x100ms 000-99 0 – 999ms
9
Force arm / bypass
This option defines whether a zone is allowed to be force armed or bypassed. The following
options are possible:
–
Disable forced arming and bypass
–
Allow forced arming
–
Allow bypassing
–
Allow both forced arming and bypassing
Force arm
If forced arming is allowed, a zone can be armed when it is in triggering status. If forced
arming is not allowed, the system does not allow the user to arm the system unless the zone
with problems has resumed to normal status or been manually bypassed.
The arming with a zone in triggering status is called forced arming.
When the operating system arms:
–
When the keypad or key switch zone is used to execute system arming, the system will
show the zone status at first. If a zone in triggering status is not bypassed and the forced
arming option is in disabled status, it cannot be successfully armed.
–
When the keypad or key switch zone is used to execute system arming, the system shows
the zone status at first. If a zone in triggering status is not bypassed and the forced
arming option is in enabled status, the system is successfully armed. If the zone is still
not recovered at the end of the exit delay time, the system shows the fault report of the
zone.
–
When the fault is recovered, a zone recovery report is sent.
The exceptions to forced arming option:
–
In telephone and programming software remote arming, forced arming is available even if
the zone is programmed as enabled or disabled forced arming.
Bypassing
If bypassing is allowed, the operator can bypass zones before arming the system. If bypassing
is not allowed, manual bypass of the zone is not available. After manual bypass of the zone, a
zone bypass report is sent.
The zone bypass is valid in only one arming period and will be resumed after disarming. Before
disarming, the bypassed zones ignore all zone triggering and restoration events.
The key switch zone cannot be bypassed.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
72
en | Settings
AMAX panel
Silent alarm / chime mode
This option defines whether silent alarm and chime mode are allowed for a zone. The
following options are possible:
–
Disable silent alarm and chime mode
–
Allow silent alarm
–
Allow chime mode
–
Allow both silent alarm and chime mode
Silent alarm
Allowing the silent alarm option can set the zone to mute alarm. Silent alarm will not trigger
the output of keypad buzzer and the output of the type of event of system audio alarm, but
can trigger the output of the type of event of system alarm (both sound and silent) and the
alarm event can still be transmitted according to programming path.
Chime mode
If chime mode is allowed, the process is as follows:
If the chime mode is used and a zone is triggered the keypad buzzer will sound for 1 second
(only in disarmed status).
Zone pulse count
This option defines whether the zone pulse count mode is allowed for a zone.
The process is as follows:
–
Pulse count duration time must be configured
–
Pulse count for a zone can be set to a value between 1 and 9 (0 = disabled)
The process is as follows:
–
An alarm is created only if the zone is triggered as many times as the value “pulse count”
within the time “count duration”
4
For more information, refer to Pulse count duration programming, page 137.
Zone lockout
The zone lockout defines after how many times of triggering an alarm during one arming cycle,
the zone in which the alarm occurred will be “locked”. If a zone is locked, the alarms its
alarms will be ignored by the system. This option defines whether the zone lockout mode is
allowed for a zone and after how many times of triggering an alarm the zone will be locked.
The following selections are possible:
–
Disabled
–
Locked after triggering the alarm 1 time
–
Locked after triggering the alarm 3 times
–
Locked after triggering the alarm 6 times
–
Alarm duration
The zone lockout will be reset after disarming.
1 time
The AMAX panel will process locking according to the following logic:
1.
When an alarm is triggered within the period of alarm output time, the AMAX panel will
ignore the status detection of the zone.
2.
After the alarm has been triggered 1 time, the zone will be locked.
3.
If the alarm occurs in the locked zone, the zone will send zone fault report.
4.
Before the end of the alarm output time, ten zone recovery events will not be transmitted.
5.
If the zone locking option is disabled, the times of alarms will not be restrained. Even
when other zones are locked, that zone can still generate the alarm.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
Settings | en
AMAX panel
73
3 times
Similar to 1 time of alarm locking, with alarm limited to not more than 3 times.
6 times
Similar to 3 times of alarm locking, with alarm limited to not more than 6 times.
Alarm duration
Locking occurs within the period of alarm output time. Repeating the process of alarm locking
in the period of alarm output time, without limit to times.
Zone EOL
The system supports tamper detection of the zone. This function ensures that the zone is in
normal operating status and triggers an alarm if not. The following selections are possible:
–
0 = EOL 2,2k
–
1 = DEOL 2,2k / 2,2k
–
2 = reserved
–
3 = NC
–
4 = NO
EOL 2,2k (end of line)
An EOL resistor with 2,2k is required for the zone. A zone alarm is triggered if another value
than 2,2k is registered.
DEOL 2,2k / 2,2k (double end of line)
A DEOL resistor with twice 2,2k is required for the zone. A zone alarm is triggered if 4,4k are
registered. A tamper alarm is triggered if any other value is registered.
NC (normally closed)
A NC resistor is required for the zone. A zone alarm is triggered if the resistor is closed.
NO (normally open)
A NO resistor is required for the zone. A zone alarm is triggered if the resistor is opened.
Zone status report
This option defines whether and to which destinations a zone status report is sent.
The AMAX panel reports the zone status according to the specified path, including alarm, zone
fault, zone bypass and zone tamper alarm.
Unverified alarm report / cross zone
This option defines whether the unverified alarm report and cross zone options are allowed
for a zone. The following selections are possible:
–
Disable unverified alarm report and cross zone option
–
Allow unverified alarm report option
–
Allow cross zone option
–
Allow both unverified alarm report and cross zone option
Unverified alarm report
If the unverified alarm report option is allowed and when a cross zone is triggered, but no
alarm is created, system creates an unverified alarm in order to report. The system reports
unverified alarms if option unverified alarm report is enabled.
Cross zone
If the cross zone option is allowed, the process is as follows:
Prerequisites:
–
At least two zones in the same area have option cross zone enabled
–
System option cross zone timer is set to a value higher than 0
When one of these zones is triggered for more than 20 seconds, an alarm is created.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
74
en | Settings
AMAX panel
When one of these zones (the first zone) is triggered for a shorter time than 20 seconds, the
cross zone timer starts, no alarm is created at this time
–
When no more zones (with cross zone option) are triggered within the cross zone time,
no alarm is created
–
When the first zone is triggered twice or more within the cross zone time, no alarm is
created
–
When a second zone or further zones (with cross zone option) is / are triggered within
–
When the first zone or one of the other zones (with cross zone option) is / are triggered
the cross zone time, then an alarm is created for all triggered zones
twice or more after cross zone time is expired, the timer restarts
Zone domestic call
The system supports domestic call mode.
The process is as follows:
–
If the domestic call mode is configured for a zone and an alarm from this zone is created
the alarm will be reported via the onboard voice dialer to the destination(s) configured
and needs acknowledgement.
Zone alarm on keypad
This option enables / disables the zone alarm on the keypad. If this option is enabled, a zone
alarm can be sounded on the keypad buzzer. The alarm is only indicated on the keypad. An
output will not be triggered.
If the keypad alarm tone function is disabled and the zone alarm on keypad function is
enabled, the alarm tone on the keypad is still enabled.
If the keypad alarm tone function is enabled and the zone alarm on keypad function is
disabled, the alarm tone on the keypad is still enabled.
For more information on the keypad alarm tone, refer to Keypad alarm tone, page 77.
Trouble domestic
This option enables / disables the domestic call for trouble. If this option is disabled and a
trouble event occurs for the zone, a domestic call will not be sent.
Detection time x100ms
This option defines the amount of time in ms which has to pass before an event will be
recognized. Any event that occurs and disappears before that amount of time has passed will
be ignored. Possible values are 0 to 999ms.
6.3.3
Pulse count duration
The pulse code duration defines the period for the zone pulse count feature.
6.3.4
Cross zone timer
The cross zone timer defines the period for the cross zone feature.
6.3.5
Zone indication keypad and event log
Zones may be indicated on LED/LCD keypads and in event logs with a number that are
different from the zone number used for programming and hardware input.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Settings | en
75
One area system
Zones are indicated on LED/LCD keypads according to the zone numbers. When one zone is
disabled the indication number of all following (higher) zone numbers will shift to a value
decreased by one.
Multi area system
Only zones assigned to one area are indicated on an area LED/LCD keypad in order beginning
with 1 and by following the order of zone numbers.
Examples:
AMAX 3000 / 3000 BE / 4000:
In a one area or area 1 system keypad the zone number 17 is indicated on a 16 zone LED/LCD
keypad. After disabling zone 16 (or another one in range 1 to 16), zone number 17 is indicated
on the LED/LCD keypad as zone number 16.
AMAX 2100:
In a one area system keypad the zone number 17 is indicated on an 8 zone LED/LCD keypad.
After disabling zone 5, zone number 17 is indicated on the LED/LCD keypad as zone number
5.
The following table shows the area assignment and keypad indication of zones in a multi area
system:
Zone Number
Area
1
2
1
2
2
2
3
1
1
4
1
2
5
1
3
6
1
4
7
2
3
8
2
4
9
2
5
10
2
6
11
1
5
12
1
6
6.4
Keypads and areas
6.4.1
Keypad area
Indication keypad area 1
Indication keypad area 1
Master keypad
The AMAX panel supports master keypads. User access to a master keypad differs from user
access to an area keypad. The master keypad switches to the master keypad mode or to the
area that the user declares after entering the user code. The arming/disarming, area alarm, AC
power fault, system fault and system event of each area can be displayed on the master
keypad. The master keypad can also enter the user menu.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
76
en | Settings
AMAX panel
It is possible to execute arming/disarming on a master keypad. It is possible to either arm all
areas or to arm only a single area via the direct arm function.
It is not possible to perform a bypass operation on a master keypad. When relevant operations
are made to an area, the master keypad should be switched to the corresponding area.
Area keypad
It is possible to operate each area with a single or multiple independent keypads.
Each area keypad can only operate the corresponding programmed area.
When the area keypad has no corresponding zones, the area keypad cannot be used to
execute zone-related operations such as arming/disarming and bypassing, but can be used to
execute operations unrelated to zones, e.g. event inquiry.
Each area keypad can display the status of the zone belonging to the area. However, for IUIAMAX3- LED8 keypad, IUI-AMAXLED 8 keypad and IUI-AMAX-LCD 8 keypad, each area can
display up to 8 zones and cannot display other zones, but can report zone events. For IUIAMAX3LED16 keypad, each area can display up to 16 zones and cannot display other zones,
but can report zone events. Keypad IUI -AMAX4-TEXT can display up to 64 zones.
How to program keypads
–
To program a master keypad via installer menu programming, enter area 00 in the section
KEYPAD IN AREA.
–
To program a master keypad via address programming, enter area 00 into the
corresponding addresses.
–
To program an area keypad via installer menu programming, enter area 01 – 16 in the
section KEYPAD IN AREA.
–
To program an area keypad via address programming, enter area 01 – 16 into the
corresponding addresses.
For keypad no. 1 the default setting is area 01
For keypads no. 2 – 16 the default setting is 99 for not used.
Displaying areas in a LED/LCD keypad
For any area, the logic numbers of the zones are displayed on the LED/LCD keypad and logic
numbers or zone names of the zones are displayed on the keypad instead of actual physical
numbers. For example: The zones 1, 2, and 3 of 1 area or area 1 displayed on the keypad are
actually zones 20, 31, and 37.
6.4.2
Entry/exit timing
The AMAX panel supports separate entry and exit delay times for each area.
Exit delay
The programming range is 0 - 255 seconds. In the mode of system arming, the keypad will
beep during exit and will make continuous long beep sound in the last 10 seconds to notify
the exit time is coming to an end.
Entry delay 1
The programming range is 0 - 255 seconds. Entry delay time starts when a delay zone 1 (zone
type 03, 04, 05, 06) is triggered in armed state.
Entry delay 2
The programming range is 0 - 255 seconds. Entry delay time starts when a delay zone 2 (zone
type 07, 08, 09, 10) is triggered in armed state.
Entry and exit delay time audible
This option defines whether an entry or exit delay time is silent or audible. One or more of the
following entry and exit delay time scenarios can be selected individually for audible or silent
indication of entry and exit time.
–
2016.05 | 08 | F.01U.309.277
Entry time (STAY) for area keypad
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Settings | en
–
Exit time (STAY) for area keypad
–
Entry time (STAY) for master keypad
–
Exit time (STAY) for master keypad
–
Entry time (AWAY) for area keypad
–
Exit time (AWAY) for area keypad
–
Entry time (AWAY) for master keypad
–
Exit time (AWAY) for master keypad
77
Per default, all entry and exit time scenarios are set to audible indication.
6.4.3
Common area
Area 1 can be used as an independent or a common area with other areas being subordinated.
If area 1 is a common area the following applies:
–
Only when all subordinate areas are armed, the common area can be armed.
–
If a subordinate area is in STAY arm mode, the common area is in STAY arm mode too.
–
If a subordinate area is disarmed, the common area will be disarmed too.
–
If any zones under common zones are triggered or in tamper status and forced arming is
disabled, the common area cannot be armed.
Common area indication
If area 1 is a common area, the following icons are used to indicate the status on the keypad:
Indication on keypad
Description
COMM ✓
No event in common area, no open zones
COMM Ø
Event in common area if force arming is
disabled for the zone, e.g. open zone
READY
No event in area, no open zones
Ø READY
Event in area if force arming is disabled for
the zone, e.g. open zone
The following cases of common area and subordinate areas behavior are possible:
Area 1
Case 1
Case 2
Case 3
Case 4
Case 5
COMM ✓
COMM Ø
COMM Ø
COMM ✓
COMM Ø
READY
READY
Armed / exit
Armed
Armed
Ø READY
Ø READY
(common
area)
Area 2
delay
Area 3
6.4.4
READY
READY
COMM Ø
Keypad indication
Keypad alarm tone
This option enables / disables the area keypad alarm tone.
If the keypad alarm tone function is disabled and the zone alarm on keypad function is
enabled, the alarm tone on the keypad is still enabled.
If the keypad alarm tone function is enabled and the zone alarm on keypad function is
disabled, the alarm tone on the keypad is still enabled.
For more information on the zone alarm on keypad, refer to Zone alarm on keypad, page 74.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
78
en | Settings
AMAX panel
Alarm indicator enable
This option enables / disables the alarm indication on keypads depending on the arming
status. The following selections are possible:
–
Disabled
–
STAY armed enabled
–
AWAY armed enabled
–
Both enabled
Backlight on entry time
This option enables/disables the keypad backlight during entry time. If this option is enabled,
the keypad backlight turns on when the system is in STAY arm mode and the entry time starts
and turns off when the entry time ends and no other button is pressed.
Keypad LED expiration
This option defines the keypad LED indication timeout in seconds when armed. Possible
values are 00 - 99. If 00 is selected, the LED indication stays on.
Master keypad LED on
This option defines the LED indication of the master keypad. The following selections are
possible:
–
0 = disable
–
1 = 1st area on
–
2 = 1st area flash
–
3 = all area on
–
4 = 1st area on ex
–
5 = 1st area flh ex
–
6 = all area on ex
0 = disable
The master keypad LED indication is disabled.
1 = 1st area on
When the first area is armed, the master keypad LED is on (STAY or AWAY LED, depending on
the arming mode).
When no area is armed, the master keypad LED is off.
2 = 1st area flash
When the first area is armed, the master keypad LED is flashing (STAY or AWAY LED,
depending on the arming mode).
When all areas are armed, the master keypad LED is on (STAY and / or AWAY LED, depending
on the arming mode).
When no area is armed, the master keypad LED is off.
3 = all area on
When all areas are armed, the master keypad LED is on (STAY and / or AWAY LED, depending
on the arming mode).
When no or not all areas are armed, the master keypad LED is off.
4 = 1st area on ex
When the first area is armed, the master keypad LED is on (STAY and / or AWAY LED,
depending on the arming mode).
When no area is armed, the master keypad LED is off.
During the exit time, the master keypad LED is flashing (STAY and / or AWAY LED, depending
on the arming mode).
5 = 1st area flh ex
When the first area is armed, the master keypad LED is flashing (STAY and / or AWAY LED,
depending on the arming mode).
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Settings | en
79
When all areas are armed, the master keypad LED is on (STAY and / or AWAY LED, depending
on the arming mode).
When no area is armed, the master keypad LED is off.
During the exit time, the master keypad LED is flashing (STAY and / or AWAY LED, depending
on the arming mode).
6 = all area on ex
When all areas are armed, the master keypad LED is on (STAY and / or AWAY LED, depending
on the arming mode).
When no or not all areas are armed, the master keypad LED is off.
During the exit time, the master keypad LED is flashing (STAY and / or AWAY LED, depending
on the arming mode).
Master keypad alarm tone
This option enables / disables the master keypad alarm tone.
For panic, fire and medical alarms that are triggered on a master keypad, this option defines
whether a master keypad alarm tone occurs or not, no matter what settings are configured for
the option keypad alarm tone.
For all other alarms, faults and tampers, this option defines whether the master keypad alarm
tone settings follow the area keypad alarm tone settings or not.
Master keypad restore
This option defines the time in seconds after which a master keypad switches back from area
mode to master mode. Possible values are 00 -99. If 00 is selected, the keypad never switches
back to master mode.
6.4.5
Keypad lockout
Follow EN standard
This option defines whether the EN standard concerning keypad lockout is followed or not. If
this option is enabled, the EN standard concerning keypad lockout is followed. That means
that when it is possible to attempt access more than 3 times in a period of 60 second, then
the number of successive failure attempts is limited to 3. The keypad will then be locked for 5
minutes.
If this option is enabled, the option “keypad lock count” cannot be configured anymore.
Keypad lock count
The number of attempts to enter a wrong user code can be set from 1 to 15 in order to
supervise valid user access. The keypad will be locked for 3 minutes, when the number of
attempts reaches the declared value.
This option is only available if the option “Follow EN Standard” is disabled.
6.5
System
6.5.1
System setting
This chapter describes the system settings that can be accessed via the SYSTEM SETTINGS 1
and the SYSTEM SETTINGS 2 menu and their submenus if available.
Date and time
Change date and time
The AMAX panel has a 24-hour clock and a 12-month calendar that need to be set after power
up. The order is day, month, year, hour, and minute, with each item occupying two digits [DD]
[MM] [YY] [HH] [MM].
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
80
en | Settings
AMAX panel
DST options
The daylight saving time setting determines when daylight saving time will start and end.
Therefore, date and time has to be set correctly.
Predefined daylight saving time settings are available for four regions. Alternatively, a daylight
saving time setting can be configured individually.
Daylight saving time starts and ends according to the daylight saving time settings of a certain
region. Individually configured daylight saving time starts and ends at 1 a.m.
The daylight saving time settings are the following:
1 - Euro
Europe, Azerbaijan, Turkey, Lebanon, Cyprus
2 - Brazil
Southern region of Brazil
3 - Mexico
Southern region of Mexico
4 - US nor Mexico
USA, Canada, northern region of Mexico
5 - Customize
Can be customized individually
Fault configuration
Fault sound reminder
When the command [2] [1] on the keypad is used for fault inquiry, the keypad can be
programmed to sound prompt tone to indicate new system fault. The system is defaulted to
enable. In case of a new fault, all keypads will sound a short beep once a minute.
AC fault delay time
The fault report to display on the keypad will be delayed for the selected time (01 – 98
minutes; default = 60 minutes; disabled = 99).
Date/time fault
In case of date/time settings fault, it is possible to choose to display the fault or transmit fault
prompt tone at the same time, or to not display and stop fault prompt tone. If it is chosen to
not display, the fault prompt tone is set, and the system will prompt nothing if no date and
time are set after power-up.
Battery check interval
This option defines the time interval in which the battery test is carried out (01 – 15 minutes;
00 = disabled). The battery test is also carried out when the system is armed or during system
power up.
Phone line supervision
If this option is enabled, the system supervises whether the phone line is broken or
disconnected.
Siren supervision
If this option is enabled, the system supervises whether the siren is shortened or
disconnected.
The possible values are:
–
Disabled
–
Siren 1 monitored
–
Siren 2 monitored
–
Siren 1 and 2 monitored
AC fault auto reset
This option enables/disables the automatic AC fault reset function.
If this option is enabled, an AC fault indication is restored automatically after the AC power
supply is restored.
If this option is disabled, an AC fault indication has to be reset manually after the AC power
supply is restored.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
Settings | en
AMAX panel
81
Communication fault auto reset
This option enables/disables the automatic communication fault reset function.
If this option is enabled, a communication fault indication is restored automatically after the
communication is restored.
If this option is disabled, a communication fault indication has to be reset manually after the
communication is restored.
Phone fault auto reset
This option enables/disables the automatic phone fault reset function.
If this option is enabled, a phone fault indication is restored automatically after the phone is
restored.
If this option is disabled, a phone fault indication has to be reset manually after the phone is
restored.
General fault auto reset
This option enables/disables the automatic general fault reset function.
If this option is enabled, any fault indication is restored automatically after the fault is
restored.
If this option is disabled, any fault indication has to be reset manually after the fault is
restored.
Quick arming
This option enables/disables the quick arm function via which the user can arm the system by
pressing and holding [*] / [#] for three seconds without entering the code.
Installer access until next arming
Before using installer access, a standard user has to enable installer access first. If the option
installer access until next arming is enabled, installer access permission is limited to next
arming.
Force arm when system is in trouble condition
This option enables/disables the forced arming of an area although it is in a fault or tamper
condition.
Event record count per set/unset period
This option defines the maximum number of records for an event within the set / unset period.
Language version
In this option, the currently used language can be changed to the displayed languages.
Keypad 2 button alarm
This option enables/disables the keypad 2 button function:
The emergency alarm is transmitted, if [1] and [3], or [*] and [#] are pressed on the keypad
and held for three seconds. The fire alarm is transmitted, if [4] and [6] are pressed and held
for three seconds. The silent keypad emergency alarm is transmitted, if [7] and [9] are
pressed and held for three seconds.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
82
en | Settings
AMAX panel
System tamper indication
System tamper all areas
In case of a system tamper event, all keypads indicate an alarm. This option defines the
behavior of the alarm on the keypad for area 01 if the alarm is acknowledged on a master
keypad.
–
0 = area 1:
If the tamper event alarm is acknowledged on a master keypad and 0 = area 1 is selected,
the alarm on the keypad for area 01 is still indicated and has to be acknowledged
separately.
–
1 = all areas:
If the tamper event alarm is acknowledged on a master keypad and 1 = all areas is
selected, the alarm on the keypad for area 01 is not indicated any more.
Zone tamper bypass when DEOL zone is bypassed
If the option is enabled, the system creates a tamper alarm when DEOL zone is tampered,
even when this zone is bypassed or isolated.
Enclosure tamper timing
The AMAX panel supports different response times for the onboard tamper used for panel
enclosure. The response time value range is 000.0-999.9 seconds.
Area name
This option is used to name areas. The maximum length of an area name is ten characters.
4
Use the numbers on the text keypad as an alphabetical input.
Number on the
Alphabetical input when number is pressed consecutively
text keypad
1
.,'?!"1-()@/:_¹²³©®º«»µ¶
2
abc2æåäàáâãçćč
3
def3èéêëðę
4
ghi4ìíîïğ
5
jkl5£
6
mno6öøòóôõñ
7
pqrs7ßšśş
8
tuv8ùúûüűţ
9
wxyz9ýþźżžŸ
*
Switches between small letters and capital letters
0
space 0 ; + & % * = < > £ € $ ¥¤ [ ]{}\ ~ ^ ` ¿ ¡ § # |
Company name
This option is used to name the company in which this AMAX system is used.
4
2016.05 | 08 | F.01U.309.277
Use the numbers on the text keypad as an alphabetical input.
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Settings | en
83
Voice default
This option enables/disables the voice default settings for the domestic call. If DEFAULT
VOICE YES is selected, all recorded voice messages are deleted and the default tone is used
for domestic calls. For more information on recorded messages and domestic calls, refer to
Call back and domestic call, page 51.
Schedule programming
This function is used to schedule operations according to the needs of the users. The
following operations can be scheduled:
–
Arming/disarming
–
Switching output on/off
–
Activating/deactivating users
It is possible to schedule up to 16 operations on a daily or hourly basis.
Notice!
Please note that this function can only be accessed and programmed via the remote
programming software A-Link Plus.
How to program a schedule
1. Select the function you want to schedule. The following function can be selected:
Arm (up to 16 areas)
Disarm (up to 16 areas)
Switch on output (up to 20 outputs)
Switch off output (up to 20 outputs)
Activate user (up to 250 users)
Deactivate user (up to 250 users)
6.5.2
2.
Enter the desired start time (hh:mm) and the date (dd/mm) for the schedule.
3.
Choose the selected days for the schedule (yes/no for each weekday).
4.
Optionally select a exception (e.g. for holidays)
P
The schedule is programmed and can be enabled/disabled by the user.
System view
Fault analysis
This option display faults, tampers and the bypass/isolate status. The AMAX panel can display
eight categories of 41 types of system faults and tampers.
How to display faults and tampers via a text keypad
In a text keypad the faults and tampers are displayed directly.
How to display faults and tampers via a master keypad
In a master keypad the system faults and tampers are displayed directly. After an area is
selected, the area-specific faults and tampers are displayed.
How to display the bypass status
1. Enter your code + [3] [3] and press [#].
The system beeps twice and the bypassed zones are displayed.
2.
Use [▲] and [▼] to display all bypassed zones.
3.
Press [#] to exit.
How to display the isolate status
1. Enter your code + [3] [6] and press [#].
The system beeps twice and the isolated zones are displayed.
2.
Use [▲] and [▼] to display all isolated zones.
3.
Press [#] to exit.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
84
en | Settings
AMAX panel
How to display faults and tampers via a LED/LCD keypad
1. Enter your code + [2] [1] and press [#].
The system beeps twice. The FAULT indicator is extinguished and the STAY and AWAY
indicators flash. One of the number indicators is lit. Example: 2.
2.
Enter the number that is lit in the system. Example: 2.
One of the number indicators is lit. Example: 1.
3.
Repeat step 2 until there is no number lit anymore.
4.
Refer to the table Types of fault or tamper conditions for a description of the fault or
temper. The consecutively lit number indicators correspond to fault or tamper types.
Example: 2 – 1, which indicates a panel AC failure.
5.
If necessary press [0] to return to step 2.
6.
Press [#] to exit.
P
The STAY and AWAY indicators are extinguished and the FAULT indicator is lit.
For an overview of the possible faults and tampers and how to solve them, see Trouble fault
inquiry, page 152.
Firmware version
This option displays the current firmware version.
6.5.3
System factory default
The system can be reset to the factory default settings either via software or via hardware.
Recorded voice messages are not automatically deleted when the system is reset to the
factory default setting. Voice messages have to be deleted separately. Therefore, refer to Voice
default, page 83.
How to reset the system to the factory default settings via software
Factory default
This option resets the system to the factory settings.
4
Select DEFAULT PANEL YES if you really want to reset the system or select DEFAULT
P
All programming parameters are reset to factory default.
PANEL NO if you don’t want to reset the system.
PAD default option
This option enables/disables the possibility to reset the system via hardware. If this option is
disabled, the system can not be reset via hardware any more.
How to reset the system to the factory default settings via hardware
The system can be reset to factory default settings with the ‘resetting to factory default’ pads
at the top on the printed circuit board on the main board of the AMAX panel if this possibility
is enabled in the software.
1.
Disconnect the AC power supply and the backup battery.
2.
Short-circuit the “resetting to factory default” pads.
3.
Power up the system.
Quick flash of the red LED indicator on the printed circuit board of the AMAX panel
indicates that the factory default is reset.
P
All programming parameters are reset to factory default immediately after releasing the
short-circuited bonding pads.
Notice!
If the default pads are short-circuited for over 10 seconds after power-up, the AMAX panel
discards resetting to factory default.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Settings | en
6.6
Outputs and sirens
6.6.1
Outputs
85
Onboard / extension output
The AMAX panel is equipped with on-board outputs and supports DX3010 output extension
modules with each extension module supporting 8 relay outputs.
When on-board output 1 or 2 fails due to a short circuit or an open circuit, as long as there is a
backup power supply, the output fault will not affect the normal operation of the whole
system, but will be detected by the system, if monitoring of siren 1 is enabled. Refer to Siren
supervision, page 80.
Each output is programmable and can be set to follow multiple events.
Depending on the type of the output event, the output parameters can be defined as area
output or follow zone alarm output. The output polarity of each output can be programmed
and defined as one of the following modes: continuous output, pulse output or inverted
output.
The maximum output time is specified by programming and will automatically be reset after
expiration.
Output event types
For one output up to three output event types can be defined. For each of the three output
event types the output area and zone, the output mode and output time can be set
individually. In case of an alarm, output, output event type 1 has the highest priority; output
event type 3 has the lowest.
Output event types - overview
Description
Output area / zone
00
Not used
No
01
System disarmed
0 = All areas
02
System armed
03
System alarm
04
System alarm (audible and silent)
05
External AWAY siren
06
External STAY siren
07
Internal siren
08
Internal siren with tamper
09
Entry / exit delay warning
10
Telephone line fault
11
AC power supply fault
12
Low battery
13
Tamper
Output event
type
1 - 16 = areas 1 - 16*
0 = Any area
1 - 16 = areas 1 - 16*
1 - 16 = areas 1 - 16*
0 = Any area
1 - 16 = areas 1 - 16*
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
86
en | Settings
AMAX panel
14
External fault
15
All faults
16
Fire alarm
17
Fire reset
18
AWAY armed
19
STAY armed
20
Reset
0 = Any area
1 - 16 = areas 1 - 16*
0 = All areas
1 - 16 = areas 1 - 16*
0 = Any area
1 - 16 = areas 1 - 16*
21
Follow zone event
Zone number 1 - 64*
22
RF keyfob button 3 (e.g. garage
0 = Any area
door)
1 - 16 = areas 1 - 16*
23
RF keyfob button 4 (e.g. light)
24
Chime indication
25
Verified alarm
26
Unverified alarm
27
Technical alarm
28
Bypassed zone
29
Ready to arm
30
Walk test output mode
31
24h alarm
32
24h panic alarm
33
Medical alarm
34
RF power fault
0 = Any repeater
35
Follow zone
0 = Any area
0 = All areas 1 - 16 = Areas 1 - 16*
0 = Any area
1 - 16 = areas 1 - 16
1 - 16 = areas 1 - 16
36
Schedule
Table 6.1: The value ranges of output event options
* AMAX 2100 areas 1 - 2 zones 1 - 8
AMAX 3000 / 3000 BE areas 1 - 8 zones 1 - 32
AMAX 4000 areas 1 - 16 zones 1 - 64
Output events - detailed description
00 - Not used
01 - System disarmed
The output is operated in the following cases:
–
2016.05 | 08 | F.01U.309.277
The system is disarmed after a system reset.
Installation Manual
Bosch Sicherheitssysteme GmbH
Settings | en
AMAX panel
–
87
The system operated the disarm command.
The output is reset in the following cases:
–
The system is armed.
–
The programmed output time ends.
02 - System armed
The output is operated in the following cases:
–
The system is armed after a system reset.
–
The system operated the arm command. (After the exit time ends.)
The output is reset in the following cases:
–
The system is disarmed.
–
The programmed output time ends.
If the output time is set to 000, the output will continue until the system is disarmed.
03 - System alarm
This output is operated when an alarm occurs.
The output is reset in the following cases:
–
The system is disarmed and alarm is reset.
–
The programmed output time ends.
In case of a new alarm, the output time will be reset.
If the output time is set to 000, the output will continue until the zone is restored or the
system is disarmed.
04 - System Alarm (audible and silent)
This output is operated in case of an audio alarm of the system:
–
Zone (alarm or tamper) programmed to disable zone silent alarm
–
System tamper / DX2010 tamper / keypad tamper
–
Keypad alarm (emergency alarm, fire alarm, medical aid alarm)
This output also operates in case of a silent alarm of the system:
–
Zone (alarm or tamper) programmed to enable zone silent alarm.
The output is reset in the following cases:
–
The alarm is reset.
–
The system is armed.
–
The system is disarmed.
In case of a new alarm, the output time will be reset.
If the output time is set to 000 and the alarm siren sounds time to 0, the output will continue
until the alarm output is reset or the system is disarmed by entering your code + [3] [2] + [#].
The output of the following system alarms is only one second:
–
Alarm siren test
–
Pacing (tamper / alarm / reset)
–
Key switch arming or locking key switch disarming
05 - External AWAY siren
The output is operated in the following cases:
–
The system is in AWAY mode and a zone intruder alarm (intruder alarm = instant / interior
instant / delay / interior delay / delay exit / interior delay exit / follower / interior
follower / 24h (can be silenced) / fire (can be silenced) / technical alarm (can be
silenced)) occurs.
–
The system is in AWAY mode and a tamper alarm occurs.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
88
en | Settings
AMAX panel
(No output is operated when the system is disarmed.)
06 - External STAY siren
The output is operated in the following cases:
–
The system is in STAY mode and a zone intruder alarm (intruder alarm = instant / interior
instant / delay / interior delay / delay exit / interior delay exit / follower / interior
follower / 24h (can be silenced) / fire (can be silenced) / technical alarm (can be
silenced)) occurs.
–
The system is in STAY mode and a tamper alarm occurs.
(No output is operated when the system is disarmed.)
07 - Internal siren
The output is operated in the following cases:
–
The system is in AWAY mode and a zone intruder alarm (intruder alarm = instant / interior
instant / delay / interior delay / delay exit / interior delay exit / follower / interior
follower / 24h (can be silenced) / fire (can be silenced) / technical alarm (can be
silenced)) occurs.
–
The system is in AWAY mode and a tamper alarm occurs.
–
The system is in STAY mode and a zone intruder alarm (intruder alarm = instant / interior
instant / delay / interior delay / delay exit / interior delay exit / follower / interior
follower / 24h (can be silenced) / fire (can be silenced) / technical alarm (can be
silenced)) occurs.
–
The system is in AWAY mode and a tamper alarm occurs.
–
The system is disarmed and a zone tamper alarm occurs.
When the system is armed the output mode is a one pulse activation (1sec) (enabled / disable
option can be combined with disarm).
When the system is disarmed the output mode is a two pulse activation (1sec) (enabled /
disable option can be combined with arm).
When programming mode is entered the output mode is a one pulse activation (1sec)
(enabled / disable option).
08 - Internal siren with tamper
The output is operated when an internal siren with tamper occurs.
09 - Entry/exit delay warning
Entry delay warning
This output is operated during the entry time.
The output is reset in the following cases:
–
The system is disarmed.
–
The entry time expires.
–
The programmed output time ends.
Exit delay warning
This output is operated during the exit time when the system is armed.
The output is reset in the following cases:
–
The system is disarmed.
–
The exit time expires.
–
The programmed output time ends.
If the output time is set to 000, the output will continue until the delay warning time ends.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
Settings | en
AMAX panel
89
10 - Telephone line fault
This output is operated when a telephone line fault occurs.
The output is reset in the following cases:
–
The telephone line is restored and the fault is reset.
–
The programmed output time ends.
If the output time is set to 000, the output will continue until the telephone line is restored
and the fault is reset.
11 - AC power supply fault
This output is operated when an AC power fault occurs.
The output is reset in the following cases:
–
The AC power supply is restored and the fault is reset.
–
The programmed output time ends.
If the output time is set to 000, the output will continue until the AC power supply is restored
and the fault is reset.
12 - Battery fault
This output is operated when a low battery fault occurs.
The dynamic battery test is performed every four hours after the system is powered up and
every time the system is armed.
The output is reset in the following cases:
–
A dynamic battery test reports that the backup battery voltage is normal and the fault is
reset.
–
The programmed output time ends.
If the output time is set to 000, the output will continue until the battery is restored and the
fault is reset.
13 - Tamper
This output is operated when a tamper occurs.
The output is reset when the programmed output time ends.
If the output time is set to 000, the output will continue until the tamper condition is restored
and the tamper is reset.
14 - External fault
This output is operated when an external fault occurs.
The output is reset when the programmed output time ends.
If the output time is set to 000, the output will continue until the external fault is restored and
the fault is reset.
15 - All faults
This output is operated when a fault occurs.
The output is reset when the programmed output time ends.
If the output time is set to 000, the output will continue until the fault is restored and the fault
is reset.
16 - Fire alarm
This output is operated when a fire alarm occurs.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
90
en | Settings
AMAX panel
17 - Fire reset
This output is operated when a fire alarm is reset.
18 - AWAY armed
This output is operated when the system is in AWAY mode.
The output is reset when the programmed output time ends.
If the output time is set to 000, the output will continue until the system is disarmed.
19 - STAY armed
This output is operated when system is in STAY mode.
The output is reset when the programmed output time ends.
If the output time is set to 000, the output will continue until the system is disarmed.
20 - Reset
This output is operated when a reset is performed in the system.
21 - Follow zone event
This output imitates the zone alarm state. The output is operated when an alarm or a tamper
is generated in the corresponding zone.
The output is reset when the system arming or disarming or the output time ends.
22 - RF keyfob button 3
If the output time of this output is set to 000, the keyfob button 3 works as a toggle:
This output is operated when the keyfob button 3 is pressed.
The output is reset when the keyfob button 3 is pressed again.
23 - RF keyfob button 4
If the output time of this output is set to 000, the keyfob button 4 works as a toggle:
This output is operated when keyfob button 4 is pressed.
The output is reset when the keyfob button 4 is pressed again.
24 - Chime indication
This output is operated when a chime indication occurs.
25 - Verified alarm
This output is operated when a verified alarm occurs.
26 - Unverified alarm
This output is operated when an unverified alarm occurs.
27 - Technical alarm
This output is operated when a technical alarm occurs.
28 - Bypassed zone
This output is operated when a zone is bypassed.
29 - Ready to arm
This output is operated when the system is in ready to arm state.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
Settings | en
AMAX panel
91
30 - Walk test output mode
This output is operated when the system is in walk test mode.
31 - 24h alarm
This output is operated when a 24h alarm occurs. This output works only a 24-hour zone.
The output is reset when the 24h alarm is reset or the output time ends.
32 - 24h panic alarm
This output is operated when a 24h panic alarm occurs. This output works only on zone type
10.
The output is reset when the 24h panic alarm is reset or the output time ends.
33 - Medical Alarm
This output is operated when a medical alarm occurs.
The output is reset when the medical alarm is reset or the output time ends.
34 - RF power fault
The output is operated in the following cases:
–
The battery of the RF transmitter is low.
–
The battery of the RF repeater is low.
–
An AC power fault of the RF repeater occurs.
The output is reset in the following cases:
–
The RF power is normal and the system is reset.
–
The programmed output time ends.
35 - Follow zone
This output imitates the zone state. The output is operated according to the corresponding
zone.
The output is reset according to the corresponding zone.
36 - Schedule
This output is operated when a schedule is enabled.
The output is reset when the schedule is reset or the output time ends.
Output mode
Three different output modes are available.
0 - Continuous output
The output is continuous, the level is high.
1 - Pulse output
The output occurs in pulses, the period is 1 second.
2 - Continuous inverted output
The output is continuous, the level is low (level is high in idle state). When PO-1 or PO-2 is set
to inverted, supervision is disabled for these outputs.
Output time
Each output is operated for a specific time and resets at the end of output time.
The actual output time of system audio alarm, system alarm, and follow zone event is related
to the ringing of the alarm siren.
The possible output time value range is 0 - 999 seconds.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
92
en | Settings
6.6.2
AMAX panel
Sirens
Alarm Siren Ringing Time
The alarm siren ringing time is valid only when the keypad alarm tone is enabled. When an
audio alarm occurs in the system, the alarm siren begins to ring. After a valid arming /
disarming command, an alarm reset or after the alarm siren ringing duration ends, the alarm
siren stops ringing.
4
For programming of alarm time, refer to Output programming, page 144.
Beep For Warning Devices
Enables / disables beep for warning devices when the system is armed, disarmed, or during
walk test.
Internal Siren Beep as Indication
Enables / disables internal siren beep as indication when the system is armed, disarmed, or
programming mode is entered.
Silence Warning Device When Disarmed
Enables / disables silence warning device when disarmed or by pressing any key.
6.7
RF devices
6.7.1
RF options
RF receiver functionality
Enables or disables RF receiver functionality.
RF supervision interval
Disables or defines RF Supervision Interval. The interval can be set to 20 minutes, 1, 2.5, 4, 12
or 24 hours.
RF jam detect level
Defines RF jam detect level. The range is 00 - 15:
–
00 = disabled
–
01 = most sensitive
–
15 = least sensitive
RF device low level battery resound
Disables or sets the interval for keypad acoustic indication of RF device low level battery fault.
Siren beep arm / disarm (RF keyfob)
Enables or disables keypad acoustic indication on arm / disarm.
Keyfob panic option
Defines the behavior when keyfob panic button is pressed. The option can be set to no alarm,
silent alarm, or non silent alarm.
Zone missing as alarm
This option enables / disables the alarm function for a missing zone.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
6.7.2
Settings | en
93
RF devices / user
RF User
Keyfobs are designed for arming and disarming the system remotely, trigger a panic alarm, or
for additional control functionality.
To operate the buttons of the keyfob, press and hold either button for at least one sec in
order to use the desired feature.
The AMAX panel identifies keyfob users by device RFID. AMAX Keypad programming supports
entering RFID automatically for Radion devices.
4
When the keyfob RFID is asked for, press [*] for 3s to toggle between AUTO and
MANUAL mode.
When MANUAL is selected, enter the 9-digit RFID manually.
When AUTO is selected, trigger the RF device and the RFID is entered automatically.
RF Repeater
The AMAX panel identifies repeater devices by device RFID. AMAX Keypad programming
supports entering RFID automatically for Radion devices.
4
When the repeater RFID is asked for, press [*] for 3s to toggle between AUTO and
MANUAL mode.
When MANUAL is selected, enter the 9-digit RFID manually.
When AUTO is selected, trigger the RF device and the RFID is entered automatically.
RF Sensor Diagnose
The AMAX panel supports diagnostic feature for RF sensors. The keypad diagnose displays
signal/noise ratio distance. In dependency of the rating, the AMAX panel displays the numbers
of the RFID or RELOCATE. The AMAX panel keeps on polling for the signal and updates the
indication on a regular basis.
RF Repeater Diagnose
The AMAX panel supports diagnostic feature for RF repeaters. The keypad diagnose displays
signal/noise ratio distance. In dependency of the rating, the AMAX panel displays the numbers
of the RFID or RELOCATE. The AMAX panel keeps on polling for the signal and updates the
indication on a regular basis.
Clear RF devices
The AMAX panel provides the option to clear all RF devices in a step.
6.8
Key programming
Programming with the ICP-EZPK Programming Key
The programming key allows you to save or copy programming information from your AMAX
panel and to transfer it to other AMAX panels with the same applications.
The programming key can also be used to back up existing information.
4
If you have a new programming key, enter the programming mode, program the system as
required, and connect the programming key to the AMAX panel.
To connect the programming key:
4
Connect the programming key to the plug on top of the printed circuit board (PCB) of the
AMAX panel.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
94
en | Settings
AMAX panel
Notice!
Please note that the direction of the programming key should be consistent with the direction
marked on the PCB.
Caution!
If you do not enter the programming mode first, which connects the blank ICP-EZPK
!
Programming Key (blue) to the AMAX panel, no data can be uploaded / downloaded.
An unknown error may be caused if the programming mode is not exited before removing the
programming key.
How to copy parameters from the AMAX panel to the key
On a text keypad:
1.
Connect the programming key to the plug on top of the printed circuit board (PCB) of the
AMAX panel. The direction of the programming has to be consistent with the direction
marked on the PCB.
2.
If the key is write-protected, unlock the key by moving the switch on the inside of the key
to “unlock”.
3.
Select text keypad installation menu ADDRESS / KEY PROGR – COPY DATA TO KEY and
press [#].
After successfully copying the programming data of the AMAX panel to the programming
key, a confirmation tone occurs. Wrong prompt tone and display of Failure of AMAX
Panel Parameters to Key indicate a damage of the programming key data. In this case,
the data needs to be copied onto the programming key again.
4.
Unplug the programming key from the AMAX panel.
On a LED/LCD keypad:
1.
Connect the programming key to the plug on top of the printed circuit board (PCB) of the
AMAX panel. The direction of the programming has to be consistent with the direction
marked on the PCB.
2.
If the key is write-protected, unlock the key by moving the switch on the inside of the key
to “unlock”.
3.
Enter your code + [958] + [#] + [962] + [#].
How to copy parameters from the key to the AMAX panel
On a text keypad:
1.
Connect the programming key to the printed circuit board (PCB) plug of the AMAX panel.
The direction of the programming has to be consistent with the direction marked on the
PCB.
2.
If the key is write-protected, unlock the key by moving the switch on the inside of the key
to “unlock”.
3.
Select text keypad installation menu ADDRESS / KEY PROGRAM – COPY DATA TO
PANEL and press [#].
After successfully copying the programming data in the programming key to the AMAX
panel, a confirmation tone occurs. Wrong prompt tone and display of Failure of Key
Parameters to AMAX Panel indicate a damage of the programming key data. In this case,
the data needs to be copied onto the AMAX panel again.
4.
Unplug the programming key from the AMAX panel.
On a LED/LCD keypad:
1.
Connect the programming key to the printed circuit board (PCB) plug of the AMAX panel.
The direction of the programming has to be consistent with the direction marked on the
PCB.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Settings | en
2.
95
If the key is write-protected, unlock the key by moving the switch on the inside of the key
to “unlock”.
3.
Enter your code + [958] + [#] + [963] + [#].
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
96
en | Configuration
7
AMAX panel
Configuration
This chapter describes how to configure the settings of the AMAX panel. The settings can be
configured either via a text keypad or via the remote programming software A-Link Plus.
4
7.1
For detailed description of the settings, refer to Settings, page 34.
Service mode
During configuration and programming of the system, the service mode can be used. If the
system is modified during service mode, there won’t be any alarms triggered.
Service mode expiry time
The service mode expiry time defines the time for how long the service mode will be active.
Possible values are 0 - 999.
If 000 is entered, the service mode won’t be enabled.
If 999 is entered, the service mode will stay on until it is disabled.
Service mode configuration
The service mode configurations can be set via a text keypad or via A-Link Plus.
Reports can be enabled or disabled for the service mode.
Triggering outputs can be enabled or disabled for the service mode.
The keypad buzzer can be enabled or disabled for the service mode.
How to enable the service mode on a text keypad
1. Enter the installer code + [73] and press [#].
2.
Enter the service mode expiration time in minutes. Default: 999.
3.
Enable or disable the service mode report.
4.
Enable or disable the service mode output.
5.
Enable or disable the service mode keypad buzzer.
P
The system is in service mode and the triangle LED is lit.
How to disable the service mode on a text keypad
The service mode only has to be disabled if it has been enabled before.
1.
Enter the installer code + [73] and press [#].
2.
The system is in normal mode and the triangle LED is off.
7.2
Programming with a keypad
7.2.1
Text keypad programming
Access to the Menus
Accessing the programming menu
1. Confirm that the system is disarmed and that no alarm occurred.
2.
Enter the installer code. The default setting for the installer code is [1234].
The system displays [958] PROGR. MODE [-EXIT].
3.
Enter [958] + press [#].
P
You have now access to the programming menu for configuring the AMAX system.
P
The STAY and AWAY indicators flash to indicate the programming mode.
Accessing the user menu
4 Enter a user code. The default users are master user 1 (code: [2580]) and master user 2
(code: [2581]).
P
The system displays [▼/▲] USER MENU *STAY #AWAY [-] INFO.
P
You have now access to the user menu for operating the AMAX system.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
Configuration | en
AMAX panel
97
Navigation of the Menus
This section provides an overview of how to navigate the programming menu of a text keypad.
Selecting a Menu
1. Select the menu and operate according to the menu prompt.
2.
Press [▼] or [▲] to navigate to the desired menu.
3.
Press [#] to enter a menu.
Exiting a Menu
4 Press [–] to get back to the previous menu.
Confirming the Input
4 Press [#] to confirm the input.
Switching between Settings
4 Press and hold [*] for 3 seconds to switch between settings.
Operating a Menu
1. Operate according to the menu prompt.
Select the menu and enter data for specific programming items according to the display
on the keypad to complete the programming, step by step.
2.
Press [#] to confirm each step.
Exiting the Programming Menu
1. Complete all programming input by repeating the programming steps above and press [–]
to get back to the current main menu level by level.
2.
Press [–] to get to the EXIT PROG. +SAVE menu.
It is optional to save or not to save the programming data.
1.
Select EXIT PROG. +SAVE and press [#] to save the data and to exit the programming
mode.
2.
Select EXIT PROG. UNSAVED and press [#] to exit programming mode without saving
the data.
Programming Menu Structure
The following graphics show an overview of the installer menu structure displayed on a text
keypad.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
98
en | Configuration
AMAX panel
Menu Items
Parameters / Description
Certification
Default
1 COM+REPORT MANAG
RECEIVER SETTING
INPUT RECEIVER No.
FORMAT
1
1-Cid
TEL.No.(17 DIGIT)
SUBSCRIBER ID No.
Telephone No. </= 17 Digits IP = 12 Dig. + Port = 5 Dig.
0-9B-E
000000
2-sia dc03
TEL.No.(17 DIGIT)
SUBSCRIBER ID No.
Telephone No. </= 17 Digits IP = 12 Dig. + Port = 5 Dig.
0-9B-E
000000
3-conettix ip
IP/PORT 17 DIGIT
SUBSCRIBER ID No.
NETWORK ANTIREPLAY
NETW. POLLING: min
ACK WAIT TIME: sec
4-sia dc09
PROTOCOL TYPE
IP/PORT 17 DIGIT
DC09 ID No.1(3-16)
LPREF(6 DIGIT)
DC09 RRCVR ENABLE
RRCVR(6 DIGIT)
TCP/UDP TRANSMIT
DC09 ENCRYPT. OPT.
DC09 ENCRYPT. KEY
SET TIME ZONE
LOCAL TIME SYNC EN
NETW. POLLING: min
ACK WAIT TIME: sec
5-sia dc09(2xid)
PROTOCOL TYPE
IP/PORT 17 DIGIT
DC09 ID No.1(3-16)
DC09 ID No.2(3-16)
LPREF(6 DIGIT)
DC09 RRCVR ENABLE
RRCVR(6 DIGIT)
TCP/UDP TRANSMIT
DC09 ENCRYPT. OPT.
DC09 ENCRYPT. KEY
SET TIME ZONE
LOCAL TIME SYNC EN
NETW. POLLING: min
ACK WAIT TIME: sec
0-9B-E
0-disable 1-enable
EN=1
05 - 99 seconds
1-Cid
2-sia dc03
000000
1
1
05
1
000000
0
000001
0
0-disable 1-enable
0-tcp
1-udp
0-disable
1-128 bits key
2-192 bits key
3-256 bits key
0
0
0=-12:00, 1=-11:00, 2=-10:00, 3=-9:00, 4=-8:00, 5=-7:00, 6=6:00, 7=-5:00, 8=-4:30, 9=-4:00, 10=-3:30, 11=-3:00, 12=2:00, 13=-1:00, 14=+0:00, 15=+1:00, 16=+2:00, 17=+3:00,
18=+3:30, 19=+4:00, 20=+4:30, 21=+5:00, 22=+5:30,
23=+5:45, 24=+6:00, 25=+6:30, 26=+7:00, 27=+8:00,
28=+8:30, 29=+9:00, 30=+9:30, 31=+10:00, 32=+11:00,
33=+12:00, 34=+13:00, 35=+14:00
0-disable 1-enable
05 - 99 seconds
1-Cid
2-sia dc03
15
0
1
5
1
000000
0
000001
0
0-disable 1-enable
0-tcp
1-udp
0-disable
1-128 bits key
2-192 bits key
3-256 bits key
0
0
0=-12:00, 1=-11:00, 2=-10:00, 3=-9:00, 4=-8:00, 5=-7:00, 6=6:00, 7=-5:00, 8=-4:30, 9=-4:00, 10=-3:30, 11=-3:00, 12=2:00, 13=-1:00, 14=+0:00, 15=+1:00, 16=+2:00, 17=+3:00,
18=+3:30, 19=+4:00, 20=+4:30, 21=+5:00, 22=+5:30,
23=+5:45, 24=+6:00, 25=+6:30, 26=+7:00, 27=+8:00,
28=+8:30, 29=+9:00, 30=+9:30, 31=+10:00, 32=+11:00,
33=+12:00, 34=+13:00, 35=+14:00
0-disable 1-enable
05 - 99 seconds
15
0
1
5
Figure 7.1: Communications and Reporting Manager
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
Configuration | en
AMAX panel
Menu Items
REPORT SETTING
ZONE RESTORE REP.
AWAY ARM/DI REPORT
STAY ARM/DI REPORT
AC FAULT REP. REC.
AC FAULT REP. DOME
SYSTEM STATUS REP.
SYS REP. WITH DOME
PANIC ALARM REPORT
FIRE ALARM REPORT
MEDICAL AL. REPORT
AUTOM. TEST REPORT
REPORT EXP. TIME:m
RPT DEL. ENTRY T:s
PANIC 2BUTTON AL
FIRE 2BUTTON AL
MEDICAL 2BUTTON AL
Parameters / Description
0-no report
1-receiver 1
2-receiver 2
3-receiver 3
4-receiver 4
5-rec 1, 2, 3, 4
6-rec 1 (2,3,4 b)
7-rec 1,3 (2,4 b)
8-rec 1, 2
9-rec 1 (2 b)
10-rec 3, 4
11-rec 3 (4 b)
000 = No time limit 001 - 255 = 1 - 255 minutes
Certification
EN=1/5/6/7
EN=1/5/6/7
EN=1/5/6/7
EN=1/5/6/7
EN=0
SSI,EN=30
0-disabled
1-report
2-siren
3-all
99
Default
6
6
6
6
0
6
0
0
0
0
6
0
30
1
1
1
TEST REPORT DURAT.
TEST RPT INTERV: h
TEST REPORT: hour
TEST REPORT: min
DUAL IP
IP COMMUNICATOR
INPUT MODULE No.
IPV6 MODE
IPV4 DHCP
IPV4 ADDRESS
IPV4 SUBNET MASK
IPV4 DFLT GATEWAY
IPV4 DNS SERVER IP
IPV6 DNS SERVER IP
UPNP ENABLE
HTTP PORT NUMBER
ARP CA TIME(SEC)
WEB/USB ACCESS
WEB/USB PWD
FIRMWARE UPGRADE
MODULE HOSTNAME
UNIT DESCRIP.
TCP/UDP PORT NUM
TCP KEEP AL.(SEC)
ALT IPV4 DNS SERVR
ALT IPV6 DNS SERVR
AES ENCRYPTION
AES KEY SIZE
AES KEY STRING
CONFIG B450 ?
SIM PIN
NET. ACC. P NA
NET. P USR NA
NET. ACC. P PWD
0-disable
1-1 hour
2-2 hours
3-3 hours
4-4 hours
5-6 hours
6-8 hours
7-12 hours
8-24 hour
00 - 23 hours Others = Do not use real-time report
00 - 59 minutes Others = Do not use real-time report
0-1 ip module
1-2 ip modules
1,2
0-disable 1-enable
0-disable 1-enable
0.0.0.0 - 255.255.255.255
0.0.0.0 - 255.255.255.255
0.0.0.0 - 255.255.255.255
0.0.0.0 - 255.255.255.255
0000:0000:0000:0000:0000:0000:0000:0000 FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF
0-disable 1-enable
1-65535
1-600 (seconds)
0-disable 1-enable
4-10 ASCII printable characters in length
0-disable 1-enable
Up to sixty-three characters (letters, numbers, and dashes)
Up to twenty ASCII printable characters
1-65535
0-65 (seconds)
0.0.0.0 - 255.255.255.255
0000:0000:0000:0000:0000:0000:0000:0000 FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF
0-disable 1-enable
1-128 bits, 2-192 bits, 3-256 bits
32 or 48 or 64 hexadecimals characters
Only display for module 1, two options for this item:
"NO, RETURN", "YES, CONTINUE"
4-8 numbers
0-99 ASCII printable characters
0-99 ASCII printable characters
0-99 ASCII printable characters
EN=1-8
8
99
99
1
0
1
0
255.255.255.0
0
0
0
1
00080
600
0
B42V2
0
07700
45
0
0
0
1
Figure 7.2: Communications and Reporting Manager (continued)
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
100
en | Configuration
AMAX panel
Menu Items
Parameters / Description
Certification
Default
REMOTE ACCESS
REM. ACCESS ARMED
0-disable 1-enable
1
REMOTE PSTN ACCESS
0-disable 1-enable
1
REMOTE IP ACCESS
0-disable 1-enable
0
RPC ACCESS CODE
0000000000
RPC IP/ PORT/ POLL
RPC IP ADDRESS
RPC PORT 5 DIGIT!
RPC POLL: 1-15h
15
CALLBACK/ DOMESTIC
CALLBACK SETTING
0-disable 1-enable
0
CALLBACK/DOMEST No
DOMESTIC CALL
DOMESTIC No (1-4)
CHANGE DOM PHO. No
CALLBACK PHONE No
RING TIMES
0
= Panel does not answer
1 - 13 = Number of rings until the control panel responds
14
= Call the control panel and allow the phone to ring no
more than twice and hang up. Wait a minimum of 8 sec and
call the control panel again. The control panel answers on
the first ring.
15
= Call the control panel and allow the phone to ring no
more than four times and then hang up. If you call again
within 45 sec, the control panel answers the call on the first
ring.
14
Figure 7.3: Communications and Reporting Manager (continued)
Menu Items
2 CODE
Parameters / Description
Certification
Default
MANAGER
USER
CODE
USER No.
USER CODE PRIORITY
USER CODE IN AREA
USER MACRO AUTH.
CHANGE USER CODE
KEYFOB ID: MANUAL
KEYFOB ID: AUTO
KEYFOB BUTTON3
0-master 1 code
1-master 2 code
2-super
code
3-basic
code
4-arming code
5-duress code
6-not used
2580
2581
press* 3s for AUTO. 9 Digits
press* 3s for MANUAL. Trigger device, RFID will be entered
0-not used
1-output control
2-stay arm
INSTALLER CODE
1234
CODE LENGTH
4
CODE PERMISSIONS
TAMPER RESET USER
0-disable 1-enable
1
ARM/DISARM INSTAL.
0-disable 1-enable
1
DATE/TIME MASTER U
0-disable 1-enable
FORCE CODE CHANGE
MACRO CONFIG
INPUT MACRO (1-3)
LEVEL 1 ACCESS
REC T.OUT:1-80sec
PAUSE T:100ms 1-15
CODE INSIDE MACRO
0-disable 1-enable
1
EN=0
0
1
0-disable 1-enable
0-disable 1-enable
0
60
03
1
Installation Manual
Bosch Sicherheitssysteme GmbH
Figure 7.4: Code Manager
2016.05 | 08 | F.01U.309.277
Configuration | en
AMAX panel
Menu Items
3 ZONE
Parameters / Description
Certification
101
Default
MANAGER
ADD/DELETE ZONES
INPUT ZONE No.
ZONE MODULE SEL.
ZONE FUNCTION
ZONE IN AREA
ZONE NAME INPUT
ZONE RFID: MANUAL
ZONE RFID: AUTO
ZONE FUNCTION
ZONE FUNCTION No.
ZONE TYPE
FORCE ARM/BYPASS
SILENT AL./CHIME
ZONE PULSE COUNT
ZONE LOCKOUT
0-on board zone
1-keypad zone
2-input mod. zone
3-RF all
4-RF RFGB glassb.
5-RF RFUN no magn
6-not used
00 = zone not used 01 - 16 = Area 1- 16
00
press* 3s for AUTO. 9 Digits
press* 3s for MANUAL. Trigger device, RFID will be entered
00-not used
01-instant
02-interior inst.
03-delay 1
04-interior del.1
05-delay 1 exit
06-inter. del 1 e
07-delay 2
08-inter. del 2
09-delay 2 exit
10-inter. del 2 e
11-follower
12-inter. followe
13-24 hour
14-key away toggl
15-key away on/of
16-key stay toggl
17-key stay on/of
18-24 hour panic
19-24 hour fire
20-24 h fire veri
21-tamper
22-bolt contact
23-external fault
24-technical al.
25-reset
26-instant report
0-disabled
1-force arm
2-bypass
3-all
0-disabled
1-silent alarm
2-chime mode
3-all
00 = disabled 01 - 09 Pulses
0-disabled
1-1 time al. lock
2-3 time al. lock
3-6 time al. lock
4-alarm duration
EN=0/2
3
EN=0/2
0
EN=0
0
EN=0
0
Figure 7.5: Zone Manager
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
102
en | Configuration
AMAX panel
Menu Items
ZONE EOL
ZONE STATUS REPORT
UNVERF.REP/CROS.ZN
ZONE DOMESTIC CALL
ZONE ALARM ON KP
TROUBLE DOM EN
DETECT. T. x100ms
PULSE COUNT DURAT.
Parameters / Description
0-eol 2,2k
1-deol 2,2k/2,2k
2-reserve
3-nc
4-no
0-no report
1-receiver 1
2-receiver 2
3-receiver 3
4-receiver 4
5-rec 1, 2, 3, 4
6-rec 1 (2,3,4 b)
7-rec 1,3 (2,4 b)
8-rec 1, 2
9-rec 1 (2 b)
10-rec 3, 4
11-rec 3 (4 b)
0-disabled
1-unverified alar
2-cross zone
3-all
0-no report
1-destination 1
2-destination 2
3-destination 3
4-destination 4
5-dest. 1,2,3,4
6-dest 1 /2,3,4 b
7-dest 1,3 /2,4 b
8-dest. 1,2
9-dest 1 /2 b
10-dest. 3,4
11-dest 3 /4 b
0-disable 1-enable
0-disable 1-enable
000 = disabled
1 - 999 sec = Duration
CROSS ZONE TIMER
Certification
Default
1
EN=1/5/6/7
6
EN=0
0
0
0
1
3
EN=0
60
60
Figure 7.6: Zone Manager (continued)
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
Configuration | en
AMAX panel
Menu Items
Parameters / Description
Certification
103
Default
4 KP/AREA MANAGER
KEYPAD AREA
INPUT KEYPAD No.
KEYPAD IN AREA
ENTRY/EXIT TIMING
INPUT AREA No.
EXIT DELAY: sec
ENTRY DELAY 1: sec
ENTRY DELAY 2: sec
AUDIBLE: MUL SEL *
COMMON AREA
KEYPAD INDICATION
KEYPAD ALARM TONE
ALARM INDIC ENABLE
01 - 16 00 = Master 99 = not used
EN=45
entry time(stay)
exit time(stay)
ent time(sty) mst
exit tim(sty) mst
entry time(away)
exit time(away)
ent time(awy) mst
exit tim(awy) mst
00-none
01-follow area 2
02-follow ar 2-3
03-follow ar 2-4
04-follow ar 2-5
05-follow ar 2-6
06-follow ar 2-7
07-follow ar 2-8
08-follow ar 2-9
09-follow ar 2-10
10-follow ar 2-11
11-follow ar 2-12
12-follow ar 2-13
13-follow ar 2-14
14-follow ar 2-15
15-follow ar 2-16
0
MASTER KP AL TON
MASTER KP RES: sec
0-disable 1-enable
0-disable
1-stay arm
2-away arm
3-both arm
0-disable 1-enable
01-99 sec, 00=always on
0-disable
1-1st area on
2-1st area flash
3-all area on
4-1st area on ex
5-1st area flh ex
6-all area on ex
0-disable 1-enable
00-99, 00=always
KEYPAD LOCKOUT
FOLLOW EN STANDARD
KEYPAD LOCK COUNT
0-disable 1-enable
EN=1?
0-15, only valid when "FOLLOW EN STANDARD" is disabled EN=10?
BACKL. ON ENTRY T.
KP LED EXP.: sec
MASTER KP LED ON
45
30
30
yes
yes
yes
yes
yes
yes
yes
yes
1
3
EN=0/1
1
0
2
1
60
0
10
Figure 7.7: Keypad and Area Manager
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
104
en | Configuration
AMAX panel
Menu Items
Parameters / Description
Certification
Default
5 SYSTEM MANAGER
SYSTEM SETTING 1
DATE/TIME
CHANGE DATE / TIME
DST OPTIONS
0
0-disable
1-euro
2-brazil
3-mexico
4-us nor mexico
5-customize
permanent start/stop at 1 am
START DST
MONTH
ORDINAL
WEEK DAY
1=January,2=February,3=March,4=April,5=May,6=June,7=J
uly
1=1st,2=2nd,3=3rd,4=4th,5=last
1=Monday,2=Tuesday,3=Wednesday,4=Thursday,5=Friday
6=Saturday,7=Sunday
STOP DST
MONTH
ORDINAL
WEEK DAY
FAULT CONFIG
FAULT SOUND REMIND
AC FAULT DELAY T.
DATE / TIME FAULT
BATT. CHK INTERVAL
PHO. LN SUPERVISED
SIREN SUPERVISED
1=January,2=February,3=March,4=April,5=May,6=June,7=J
uly
1=1st,2=2nd,3=3rd,4=4th,5=last
1=Monday,2=Tuesday,3=Wednesday,4=Thursday,5=Friday
6=Saturday,7=Sunday
0-disable 1-enable
0-98 min 99=disable
0-disable 1-enable
00 = disabled 01 - 15 minutes
0-disable 1-enable
0-disabled
1-po-1 enabled
2-po-2 enabled
3-po-1+2 enabled
QUICK ARM ONLY */#
0-disable 1-enable
INSTALLER ACCESS
0-disable 1-enable
EN=1
EN=15
EN=1
1
60
1
15
0
EN=3
0
EN=0
1
0
SYSTEM SETTING 2
FORCE ARM FAULT/TA
0-disable 1-enable
EN=0
EVENT RECORD COUNT
3 - 10 Record count of same event per armed period
EN=3-10
1
LANGUAGE VERSION
1-EN 6-PL 9-TR
2-DE 4-FR 5-PT 7NL
1-EN 3-ES 6-PL 8SE
1-EN 3-ES 4-FR 5PT
KP 2 BUTTON ALARM
0-disable 1-enable
EN=0
1
SYS TAMPER INDIC.
SYS TAMP. ALL AR.
DEOL TAMP. BYPASS
ENCL TAMP. TIMING
0 = area1 1 = all areas
0-disable 1-enable
1 - 9999 x100ms
EN=?
3
10
AREA NAME
INPUT AREA No.
AREA NAME
COMPANY NAME
VOICE MEM. DEFAULT
DEFAULT VOICE YES
DEFAULT VOICE NO
SYSTEM VIEW
FAULT ANALYSIS
FW VERSION
FACTORY DEFAULT
DEFAULT PANEL YES
DEFAULT PANEL NO
PAD DEFAULT OPTION
0-disable 1-enable
1
Installation Manual
Bosch Sicherheitssysteme GmbH
Figure 7.8: System Manager
2016.05 | 08 | F.01U.309.277
Configuration | en
AMAX panel
Menu Items
Parameters / Description
Certification
105
Default
6 OUTPUT MANAGER
OUTPUT SETTINGS
ENTER OUTPUT No.
OUTPUT EVENT TYPE1
OUTPUT TIME3: sec
00-not used
01-syst. disarmed
02-system armed
03-sys al audible
04-sys alarm all
05-ext.away siren
06-ext.stay siren
07-int. siren
08-int. sir w.tmp
09-entry/exit del
10-tel.line fault
11-mains fault
12-battery fault
13-tamper
14-ext. fault
15-all faults
16-fire alarm
17-fire reset
18-away armed
19-stay armed
20-reset
21-follow zn even
22-RF kf button 3
23-RF kf button 4
24-chime indic.
25-verified alarm
26-unverif. alarm
27-technic. alarm
28-bypassed zone
29-ready to arm
30-walk test
31-24 hour alarm
32-panic alarm
33-medical alarm
34-RF power fault
35-follow zone
36-schedule
00 = all/any Area/s 01–16 Area 1-16
0-continuous
1-pulse
2-continuous inv
Master Timer for Outputs
see OUTPUT EVENT TYPE1
00 = all/any Area/s 01–16 Area 1-16
0-continuous
1-pulse
2-continuous inv
Master Timer for Outputs
see OUTPUT EVENT TYPE1
00 = all/any Area/s 01–16 Area 1-16
0-continuous
1-pulse
2-continuous inv
Master Timer for Outputs
SIREN SETTINGS
SIREN TIME: min
SIREN BEEP ENABLE
INT SIREN INDIC ON
SIREN OFF ANY KEY
Master Timer for Outputs
0-disable 1-enable
0-disable 1-enable
0-disable 1-enable
OUTPUT AREA/ZONE 1
OUTPUT MODE 1
OUTPUT TIME 1: sec
OUTPUT EVENT TYPE2
OUTPUT AREA/ZONE 2
OUTPUT MODE 2
OUTPUT TIME 2: sec
OUTPUT EVENT TYPE3
OUTPUT AREA/ZONE 3
OUTPUT MODE 3
5
0
0
0
0
0
0
0
000
00
1
1
1
Figure 7.9: Output Manager
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
106
en | Configuration
AMAX panel
Menu Items
7 RF
Parameters / Description
Certification
Default
MANAGER
RF SETTINGS
RF RECEIVER
RF SUPERVISION
RF JAM DETECT LEV.
RF LOW BATT REPEAT
SIREN BEEP ARM/DIS
RF KEYFOB PANIC AL
RF ZN MISSING = AL
0-disable 1-enable
0
0-disable
1-20min
2-1h
3-2,5h
4-4h
5-12h
6-24h
EN=1
00 - 15 00 = disable, 01 = most sensitive
4
12
0-disabled
1-4h
2-24h
2
0-disable 1-enable
1
0-no alarm
1-silent alarm
2-audible alarm
2
0-disable 1-enable
EN=0
1
RF DEVICES / USER
RF REPEATER
REPEATER No: 1-8
REPEATER ID: AUTO
REPEATERID: MANUAL
press* 3s for AUTO. 9 Digits
press* 3s for MANUAL. Trigger device, RFID will be entered
RF SENSOR DIAGNOSE
RF ZONE No:
RF REPEATER DIAGN.
REPEATER No: 1-8
CLR ALL RF DEVICES
CLEAR CONFIRM
CLEAR CANCEL
Figure 7.10: RF Manager
Menu Items
Parameters / Description
Certification
Default
8 ADDR./KEY PROGR.
ADDRESS PROGRAM
For Addresses, refer to Installation Guide
COPY DATA TO PANEL
copy data from blue programming key to Panel
COPY DATA TO KEY
copy data from Panel to blue programming key
Figure 7.11: Address and Key Programming
7.2.2
LED/LCD keypad programming
An LED/LCD keypad can be used to program the system but only works with address
programming (please refer to Address programming, page 111) as the programming menu can
not be displayed on the LED/LCD keypad. Therefore, it is recommended to use a text keypad
or the PC software A-Link Plus for programming the system.
Accessing the programming menu
1. Confirm that the system is disarmed and that no alarm occurred.
2.
Enter the installer code. The default setting for the installer code is 1234.
3.
Enter [958] + press [#].
P
The STAY and AWAY indicators flash to indicate the programming mode.
Navigation
Programming an option
1. Enter the required address and press [#].
2.
Enter the desired data value and press [*] to confirm.
3.
Press [#] to proceed to the next address or press [*] to get back to the previous address.
4.
Repeat step 1 if you want to program multiple options.
Exiting the Programming Mode
It is optional to save or not to save the programming data.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Configuration | en
1.
Enter [960] and press [#] to save the data and to exit the programming mode.
2.
Enter [959] and press [#] to exit programming mode without saving the data.
107
For LED/LCD keypads, the programming data is displayed by the number indicators, as
described in the graphic below.
Programming Data Indicators
Data
Value
Zone Indicators
1
2
3
4
5
6
7
8
Mains
0
1
X
2
X
3
X
4
X
5
X
6
X
7
X
8
9
X
X
X
10
11
12
13
X
X
X
X
X
X
14
X
X
15
X
X
X
Notice!
When the programming data exceeds the display range of the LED/LCD number indicators,
there will be no display on the keypad.
7.3
Communication with PC software
Communication with Bosch Software Packages
The AMAX system can communicate with the following software packages:
AMAX SDK (software development kit)
AMAX SDK is a Windows DLL (dynamic link library) used to integrate AMAX panel information
into 3rd party software. AMAX SDK integrates the AMAX panel functionalities and enables
receiving AMAX panel data with a 3rd party system management software.
AMAX SDK can connect to the AMAX panel via USB or IP.
4
For more information on AMAX SDK refer to your local Bosch contact.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
108
en | Configuration
AMAX panel
Remote programming software A-Link Plus
The AMAX system can be accessed and programmed via the remote programming software ALink Plus. All control panel and status information are accessible and an operation of the
AMAX panel from a remote location is possible.
A-Link Plus can connect to the AMAX panel via USB, IP or modem.
The AMAX panel supports remote programming via USB, telephone, or IP network using the
remote programming software A-Link Plus. The following options can be performed:
7.3.1
–
Setting the date and time
–
Uploading / downloading programming parameters
–
Remote arming / disarming of each area
–
Enabling / disabling the alarm siren of each area
–
Enabling / disabling each output
–
Maintenance
–
Domestic testing
–
Communication testing
–
Downloading voice files
–
Viewing history events
Prerequisites for connecting to A-Link Plus
Notice!
This manual describes how to connect to A-Link Plus. Programming the AMAX panel via A-Link
Plus is described in the A-Link Plus for AMAX Online Help.
Notice!
This manual describes the configuration with the A-Link Plus software in connection with the
firmware version V 1.5 or higher. If you are using an older firmware version, refer to your local
Bosch contact.
How to open A-Link Plus
1. Install A-Link Plus on your PC.
2.
Open A-Link Plus.
The default values for both Operator and Password are “ADMIN”.
How to prepare a connection
1. Select Customer –> New Customer.
The Customer Information tab opens.
2.
Under Customer Number, enter a number.
3.
Select the Control Panel Configuration tab.
4.
Under Control Panel Series, select AMAX.
5.
Under Model, select your panel model.
6.
Only for AMAX panels V1.4 and lower: Select Communication and Report manager –>
Receiver setting.
7.
Only for AMAX panels V1.4 and lower: In the column Receiver 1 and the line Subscriber
Number, enter the value that is currently programmed in your AMAX panel as receiver 1.
8.
Select Communication and Report manager –> Remote Access -> Automation Pass
code.
9.
Enter the value that is currently programmed in your AMAX panel as RPS access code.
10. Select Code manager -> Installer code.
11. Enter the value that is currently programmed in your AMAX panel as installer code.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
7.3.2
Configuration | en
109
Direct connection
A direct connection is used to connect the AMAX panel to the PC via USB.
How to connect via USB
1. Plug one end of the USB cable into USB port of the AMAX panel mainboard and the other
end into the USB port of your PC.
7.3.3
2.
In A-Link Plus, select the Link tab.
3.
Under Communication Model, select Direct Connect.
4.
Click Connect.
P
The AMAX panel is now connected to the PC.
Modem connection
A modem connection is used to connect the AMAX panel to the PC through a telephone
network.
The number of rings, the call back telephone number, and the telephone remote connection
enabled function are set on the AMAX panel. For more information, refer to Communication
operations programming, page 121.
How to connect via telephone network
Notice!
The first three steps are only necessary if you are not using the default modem string. Default
modem string: “AT&CI&D2X0&Q0S7=255S9=0+MS=B103B17”
1.
In A-Link Plus, select File –> Communication Settings.
The Communication Setting dialog box opens.
2.
Set the modem related parameters according to your telephone network.
3.
Click Save.
4.
Select the Customer information tab.
5.
Under Control Panel Phone Number, enter the telephone number associated to the
AMAX panel.
6.
Select the Link tab.
7.
Under Communication Model, select Modem Connect.
8.
If you are using the default modem string, set a checkmark for Using the default modem
string.
9.
For an automatic dialing connection, click Connect.
For a manual dialing connection, click Wait for Incoming Call and on the AMAX panel
keypad, enter the user code and press [5] [7] + [#].
P
7.3.4
The AMAX panel is now connected to the PC.
Network connection
A network connection is used to connect the AMAX panel to the PC through a IP network,
either TCP or UDP.
How to connect via IP network
1. In A-Link Plus, select File –> Communication Settings.
The Communication Setting dialog box opens.
2.
Under Local IP Address, select your latest IP address.
3.
Under Local Port, enter your correct port number.
4.
Click Save.
5.
Select the Link tab.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
110
en | Configuration
6.
AMAX panel
Under Communication Model, select Network Connect(TCP/IP SSL) or Network
Connect(UDP).
7.
Only for UDP and in case of a low transfer rate of the network or if a DX4020-G module is
used, set a checkmark for Specific network.
8.
For an automatic network connection, click Connect.
For a manual network connection, click Wait for Incoming Call and on the AMAX panel
keypad, enter the user code and press [5] [7] + [#].
P
2016.05 | 08 | F.01U.309.277
The AMAX panel is now connected to the PC.
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
8
Address programming | en
111
Address programming
With a LED/LCD keypad it is mandatory to use address programming.
With a text keypad both address programming and installer menu programming are possible.
Programming with keypad is possible only when all of zones in the system are in disarmed
status and no alarm is activated. The installer code is required for programming.
The control panel programming options are stored in a non-volatile flash memory. This
memory has all relevant configuration and user-specific data even after a total power loss.
Because the data retention time is quite long without power, reprogramming is not required
after powering up the control panel.
Notice!
It is not recommended to use other keypads or methods simultaneously to program the
system while programming with the current keypad.
The following chapters show an overview of all relevant programming options and their
addresses according to the descriptions in the chapter Settings, page 34.
8.1
Service mode
Option
Address
Default
Service mode expiration time (0 = disabled, 1 - 999 =
1702 - 1704
090
Service mode report (0 = disabled, 1 = enabled)
1705
0
Service mode alarm output (0 = disabled, 1 = enabled)
1706
0
Service mode keypad buzzer (0 = disabled, 1 = enabled)
1707
0
enabled)
8.2
Communication and report programming
8.2.1
Receiver programming
The following table shows how to program the numbers, keys, and functions for a telephone
number via address programming or via installer menu programming.
Digit required
Number to program via
Button to press via installer
address programming
menu programming
0-9
0-9
0-9
*
11
*1
#
12
*2
4 sec pause
13
*3
Terminal
15
Not required
The following table shows how to program the numbers, keys, and functions for a subscriber
ID number via address programming or via installer menu programming.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
112
en | Address programming
AMAX panel
Digit required
Number to program via
Button to press via installer
address programming
menu programming
0-9
0-9
0-9
B
11
*1
C
12
*2
D
13
*3
E
14
*4
F
15
*5
Receiver No.
Option
Address
Default
1
Transmission format for receiver (0 = not
0023
1
0000 - 0016
15
0017 - 0022
000000
0024
1
0025 - 0026
05
0027 - 0029
001
0140
1
0141 - 0142
06
0143 - 0158
000001
used, 1 = CID, 2= SIA, 3 = Conettix IP, 4 = SIA
DC 09, 5 = SIA DC09 (2x ID))
Telephone number / IP address and port (0 9, 11 = *, 12 = #, 13 = pause, 15 = terminal)
Subscriber ID number (0 - 9 = 0 - 9, 11=B,
12=C, 13=D, 14=E, 15=F)
Anti-replay for receiver (0 = disabled, 1 =
EN=1
enabled)
Acknowledge wait time for receiver (05 - 99
seconds )
Network polling time for receiver (001 - 999
minutes )
DC09 data format (1 = ADM-CID, 2 = SIADCS)
DC09 acct1 length (3 - 16, all other input is
treated as “3”)
DC09 acct1 (0 - 9 = 0 - 9, 10=A, 11=B, 12=C,
13=D, 14=E, 15=F)
000000
0000
DC09 acct2 length (3 - 16, all other input is
0159 - 0160
06
0161 - 0176
000001
treated as “3”)
DC09 acct2 (0 - 9 = 0 - 9, 10=A, 11=B, 12=C,
13=D, 14=E, 15=F)
000000
0000
DC09 Rrcvr enable (0 = disabled, other =
0177
0
0178 - 183
000001
enabled)
DC09 Rrcvr (0 - 9 = 0 - 9, 10=A, 11=B, 12=C,
13=D, 14=E, 15=F)
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Address programming | en
DC09 Lpref (0 - 9 = 0 - 9, 10=A, 11=B, 12=C,
0184 - 0189
000000
0190
0
0191 - 0254
0
DC09 TCP/UDP selection (0=TCP, 1=UDP)
0255
0
Local time auto sync enable (0=disabled,
0256
0
1708 - 1709
15
Transmission format for receiver
0053
1
Telephone number / IP address and port
0030 - 0046
15
Subscriber ID number
0047 - 0052
000000
Anti-replay for receiver
0054
1
Acknowledge wait time for receiver
0055 - 0056
05
Network polling time for receiver
0057 - 0059
001
DC09 data format
0260
1
DC09 acct1 length
0261 - 0262
06
DC09 acct1
0263 - 0278
000002
113
13=D, 14=E, 15=F)
DC09 encryption option (0=disable, 1=128
bits key, 2=192 bits key, 3=256 bits key)
DC09 encryption key (0 - 9 = 0 - 9, 10=A,
11=B, 12=C, 13=D, 14=E, 15=F)
1=enabled)
Time zone offset Gmt index* (0=-12:00,
1=-11:00, 2=-10:00, 3=-9:00, 4=-8:00, 5=-7:00,
6=-6:00, 7=-5:00, 8=-4:30, 9=-4:00, 10=-3:30,
11=-3:00, 12=-2:00, 13=-1:00, 14=+0:00, 15=
+1:00, 16=+2:00, 17=+3:00, 18=+3:30, 19=
+4:00, 20=+4:30, 21=+5:00, 22=+5:30, 23=
+5:45, 24=+6:00, 25=+6:30, 26=+7:00, 27=
+8:00, 28=+8:30, 29=+9:00, 30=+9:30, 31=
+10:00, 32=+11:00, 33=+12:00, 34=+13:00,
35=+14:00)
2
EN=1
000000
0000
DC09 acct2 length
0279 - 0280
06
DC09 acct2
0281 - 0296
000002
000000
0000
Bosch Sicherheitssysteme GmbH
DC09 Rrcvr enable
0297
0
DC09 Rrcvr
0298 - 0303
000001
DC09 Lpref
0304 - 0309
000000
DC09 encryption option
0310
0
DC09 encryption key
0311 - 0374
0
Installation Manual
2016.05 | 08 | F.01U.309.277
114
en | Address programming
3
AMAX panel
DC09 TCP/UDP selection
0375
0
Local time auto sync enable
0376
0
Time zone offset Gmt index*
1708 - 1709
15
Transmission format for receiver
0083
1
Telephone number / IP address and port
0060 - 0076
15
Subscriber ID number
0077 - 0082
000000
Anti-replay for receiver
0084
1
Acknowledge wait time for receiver
0085 - 086
05
Network polling time for receiver
0087 - 089
001
DC09 data format
0380
1
DC09 acct1 length
0381 - 0383
06
DC09 acct1
0383 - 0398
000003
EN=1
000000
0000
DC09 acct2 length
0399 - 0400
06
DC09 acct2
0401 - 0416
000003
000000
0000
4
2016.05 | 08 | F.01U.309.277
DC09 Rrcvr enable
0417
0
DC09 Rrcvr
0418 - 0423
000001
DC09 Lpref
0424 - 0429
000000
DC09 encryption option
0430
0
DC09 encryption key
0431 - 0494
0
DC09 TCP/UDP selection
0495
0
Local time auto sync enable
0496
0
Time zone offset Gmt index*
1708 - 1709
15
Transmission format for receiver
0113
1
Telephone number / IP address and port
0090 - 0106
15
Subscriber ID number
0107 - 0112
000000
Anti-replay for receiver
0114
1
Acknowledge wait time for receiver
0115 - 0116
05
Network polling time for receiver
0117 - 0119
001
DC09 data format
0500
1
DC09 acct1 length
0501 - 0502
06
Installation Manual
EN=1
Bosch Sicherheitssysteme GmbH
AMAX panel
Address programming | en
DC09 acct1
0503 - 0518
115
000004
000000
0000
DC09 acct2 length
0519 - 0520
06
DC09 acct2
0521 - 0536
000004
000000
0000
DC09 Rrcvr enable
0537
0
DC09 Rrcvr
0538 - 0543
000001
DC09 Lpref
0544 - 0549
000000
DC09 encryption option
0550
0
DC09 encryption key
0551 - 0614
0
DC09 TCP/UDP selection
0615
0
Local time auto sync enable
0616
0
Time zone offset Gmt index*
1708 - 1709
15
* The address for setting the time zone is the same for all four receivers. Therefore, only one
time zone can be set for all receivers.
Notice!
Enter a telephone number when the Contact ID or SIA is selected. Enter an IP address and
port number when the Conettix IP is selected. Anti-replay for receiver, acknowledge wait time
for receiver, and network polling time for receiver are valid only when Conettix IP is used.
How to program an IP address and port
1. Program an IP address with 17 digits: digits 1 - 12 for the IP address and 13 - 17 for the
port.
2.
Use no punctuation in the IP address.
3.
If any unit of the IP address has less than 3 digits, use 0 to fulfill the data in the higher
bits.
4.
The remaining 5 digits program the port. Port number ranges from 0-65535.
5.
If a port number has less than 5 digits, use 0 to fulfill the data.
Example
4 To program the IP address “10.16.1.222:80”, enter the following sequence into the
correspondent address:
[0 1 0 0 1 6 0 0 1 2 2 2 0 0 0 8 0]
8.2.2
Reports programming
System reports
Option
Address
Default
Zone status restore report
0120
6
AWAY arming / disarming report
0121
6 EN=1/5/6/7
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
116
en | Address programming
AMAX panel
STAY arming / disarming report
0122
6 EN=1/5/6/7
AC fault report by receiver
0138
6
AC fault report domestic
0137
0
System status report (zone fail, comm. fail, telephone line 0123
6
EN=1/5/6/7
fail, AC fail, low battery and so on.)
System status report with domestic
0139
0
Keypad panic alarm report
0124
0
Keypad fire alarm report
0125
0
Keypad medical alarm report
0126
0
Automatic test report
0127
6
EN=1/5/6/7
0 = no report, 1 = receiver 1, 2 = receiver 2, 3 = receiver 3, 4 = receiver 4, 5 = receiver 1,2,3,4,
6 = receiver 1 (2,3,4 for backup), 7 = receiver 1 (2 for backup), receiver 3 (4 for backup), 8 =
receiver 1,2, 9 = 1 (2 for backup), 10 = receiver 3,4, 11 = receiver 3 (4 for backup)
Report expiry time (000 - 999 = 0 - 999 sec.)
0135 - 0137
000
Report delay entry time (00 - 99 = 0 - 99 sec.)
1669 - 1670
30
Keypad 2 button alarm (0 = disabled, 1 = report, 2 = siren, 0141
1
3 = both)
Notice!
When the transmission format for receiver in the receiver programming is set to 0 (not used),
i.e. setting the report option as sending report to a receiver, then the AMAX panel will actually
not send any report.
Automatic test report
Option
Address
Default
Automatic test report time: interval
0128
8 VDS-A,
(0 = disable, 1 = 1 hour, 2 = 2 hours, 3 = 3 hours, 4 = 4
EN=1-8
hours, 5 = 6 hours, 6 = 8 hours, 7 = 12 hours, 8 = 24
hours)
Automatic report time: hour
0130 - 0131
99
0132 - 0133
99
0134 - 0136
000
(00 - 23 = 0 - 23 hours, others = do not use real-time
report)
Automatic report time: minute
(00 - 59 = 0 - 59 minutes, others = do not use real-time
report)
Report expiry time
(000 - 999 = 000 - 999 minutes)
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
8.2.3
Address programming | en
117
IP communicator programming
Module no. Option
Address
Default
1
DHCP enable (0 = disabled, 1 = enabled)
50000
1
IPv6 mode (0 = disabled, 1 = enabled)
50002
0
IPv4 static address (0.0.0.0 -
50004 -
000000
255.255.255.255)
50015
000000
IPv4 subnet mask (0.0.0.0 -
50028 -
255255
255.255.255.255)
50039
255000
IPv4 default gateway (0.0.0.0 -
50052 -
000000
255.255.255.255)
50063
000000
Primary DNS server IPv4 address (0.0.0.0 -
50076 -
000000
255.255.255.255)
50087
000000
Alternate DNS server IPv4 address (0.0.0.0 - 50100 -
000000
255.255.255.255)
50111
000000
Primary DNS server IPv6 address
50124 -
000000
(0000:0000:0000:0000:0000:0000:0000:000 50155
000000
0-
00000
FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF)
Alternate DNS server IPv6
50188 -
000000
address(0000:0000:0000:0000:0000:0000:0 50219
000000
000:0000 -
00000
FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF)
Local port number (0 - 65535)
50252 -
07700
50256
UPnP enable (0 = disabled, 1 = enabled)
50262
1
Web port number (0 - 65535)
50264 -
00080
50268
ARP cache timeout (1 – 600)
50274 -
600
50276
Enable encryption (0 = disabled, 1 =
50284
0
50286
1
enabled)
AES key size (1 = 128 bits, 2 = 192 bits, 3 =
256 bits)
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
118
en | Address programming
AMAX panel
Module no. Option
Address
Default
AES key string (32 or 48 or 64 hexadecimals 50292 -
01-02-0
characters)
3-04-05-
50355
06-07-0
8-09-1011-12-1
3-14-1516-01-0
2-03-0405-06-0
7-08-0910-11-1
2-13-1415-16
Web/USB password (character range from
50420 -
423432
0x20 to 0x7f, length: 4 - 10)
50429
5632
Web/USB access enable (0 = disabled, 1 =
50460
0
50462
0
Module hostname (A - Z, a - z, 0 - 9, it must
50464 -
000000
end with 00)
50591
000000
enabled)
Firmware upgrade enable (0 = disabled, 1 =
enabled)
00000
Unit description (A - Z, a - z, 0 - 9, if length
50720 -
000000
is less than 40 it must end with 00)
50759
000000
000000
…
TCP keep alive time (0 - 65)
50800 -
45
50801
Current SIM PIN (4-8 numbers, it must end
50804 -
000000
with 00)
50821
000000
000000
000
Primary network access point name
50844 -
000000
(character range from 0x20 to 0x7f, it must
51043
000000
end with 00)
000000
0000
Primary network username (character range 51244 -
000000
from 0x20 to 0x7f, it must end with 00)
000000
51305
000000
…
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Address programming | en
Module no. Option
Address
Default
Primary network password (character range 51500 -
000000
from 0x20 to 0x7f, it must end with 00)
000000
51561
119
000000
…
2
DHCP enable
50001
1
IPv6 mode
50003
0
IPv4 static address
50016 –
000000
50027
000000
50040 –
255255
50051
255000
50064 –
000000
50075
000000
50088 –
000000
50099
000000
50112 –
000000
50123
000000
50156 –
000000
50187
000000
IPv4 subnet mask
IPv4 default gateway
Primary DNS server IPv4 address
Alternate DNS server IPv4 address
Primary DNS server IPv6 address
00000
Alternate DNS server IPv6 address
50220 –
000000
50251
000000
00000
Local port number
50257 –
07700
50261
UPnP enable
50263
1
Web port number
50269 –
00080
50273
ARP cache timeout
50279 –
600
50281
Bosch Sicherheitssysteme GmbH
Enable encryption
50285
0
AES key size
50289
1
Installation Manual
2016.05 | 08 | F.01U.309.277
120
en | Address programming
AMAX panel
Module no. Option
AES key string
Address
Default
50356 –
01-02-0
50419
3-04-0506-07-0
8-09-1011-12-1
3-14-1516-01-0
2-03-0405-06-0
7-08-0910-11-1
2-13-1415-16
Web login password
50440 –
423432
50459
563200
00000
Web access enable
50461
0
Firmware upgrade enable
50463
0
Module hostname
50592 –
000000
50719
000000
00000
Unit description
50760 –
000000
50799
000000
000000
…
TCP keep alive time
50802 –
45
50803
Current SIM PIN
50824 –
000000
50841
000000
000000
000
Primary network access point name
51044 –
000000
51243
000000
000000
0000
Primary network username
51372 –
000000
51436
000000
000000
…
Primary network password
51628 -
000000
51692
000000
000000
…
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
8.2.4
Address programming | en
121
Communication operations programming
Dual IP settings
Option
Address
Default
Dual IP settings (0 = 1 IP module, 1 = 2 IP modules)
0990
0
Notice!
Dual IP settings are valid only when used in the Conettix IP format. This programming option
is valid for B426 and ITS-DX4020-G modules. ITS-DX4020-G cannot be set as No. 2 IP module.
Remote access to panel when panel Is armed
Option
Address
Default
Remote access to panel when panel is armed (0 =
0929
1
Option
Address
Default
Remote PC IP address
0930 - 0941
15
Remote PC port number
0942 - 0946
15
AMAX panel DHCP update time (hours)
0947
15
Remote programming (0 = disabled, 1 = enabled)
0970
1
Option
Address
Default
Call back setting (0 = disabled, 1 = enabled)
0972
0
Call back telephone number (see How to program a
0974 - 0989
15
Option
Address
Default
Domestic telephone number 1
1496 - 1511
15
Domestic telephone number 2
1512 - 1527
15
Domestic telephone number 3
1528 - 1543
15
Domestic telephone number 4
1544 - 1559
15
disabled, 1 = enabled)
Remote PC setting
Call back setting
telephone number via address programming, page 34)
Domestic telephone number
See How to program a telephone number via address programming, page 34
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
122
en | Address programming
AMAX panel
Ring count
Option
Address
Default
Ring count (0 = The panel does not answer any incoming
0973
14
calls.
1 - 13 = Number of rings until the control panel answers.
14 = The control panel is called, the phone is allowed to
ring only twice and hangs up. After 8 seconds the control
panel is called again and answers to the first ring.
15 = The control panel is called and the phone is allowed
to ring only four times.)
8.3
User and code programming
8.3.1
User code programming
User no.
Option
Address
Default
01 (master
Authority level (0 = master 1, 1 = master 2, 2 =
5994
0
code 1)
super, 3 = general, 4 = arm only, 5 = duress, 6 5995 - 5998
0000
5999
7
User code
6000 - 6005
258000
Keyfob RFID
6006 - 6014
15
Keyfob button 3 option (0 = not used, 1 =
6015
0
15 = no authority)
Area selection (BIT mask:
–
Area 1 -- 0000 0000 0000 0001 (0x0001)
–
Area 2 -- 0000 0000 0000 0010 (0x0002)
–
Area 3 -- 0000 0000 0000 0100 (0x0004)
–
Area 4 -- 0000 0000 0000 1000 (0x0008)
–
Area 5 -- 0000 0000 0001 0000 (0x0010)
–
Area 6 -- 0000 0000 0010 0000 (0x0020)
–
Area 7 -- 0000 0000 0100 0000 (0x0040)
–
Area 8 -- 0000 0000 1000 0000 (0x0080)
–
Area 9 -- 0000 0001 0000 0000 (0x0100)
–
Area 10 -- 0000 0010 0000 0000 (0x0200)
–
Area 11 -- 0000 0100 0000 0000 (0x0400)
–
Area 12 -- 0000 1000 0000 0000 (0x0800)
–
Area 13 -- 0001 0000 0000 0000 (0x1000)
–
Area 14 -- 0010 0000 0000 0000 (0x2000)
–
Area 15 -- 0100 0000 0000 0000 (0x4000)
–
Area 16 -- 1000 0000 0000 0000 (0x8000))
Macro play right (BIT mask:
–
Play macro 1 right -- 0001 (0x1)
–
Play macro 2 right -- 0010 (0x2)
–
Play macro 3 right -- 0100 (0x4))
output control, 2 = STAY arm)
reserved
2016.05 | 08 | F.01U.309.277
6016
Installation Manual
Bosch Sicherheitssysteme GmbH
Address programming | en
AMAX panel
02 (master
code 2)
03 (as an
example for
the
following
users 04 to
250)
Authority level
6017
1
Area selection
6018 - 6021
0000
Macro play right
6022
7
User code
6023 - 6028
258100
Keyfob RFID
6029 - 6037
15
Keyfob button 3 option
6038
0
reserved
6039
Authority level
6040
15
Area selection
6041 - 6044
0000
Macro play right
6045
0
User code
6046 - 6051
15
Keyfob RFID
6052 - 6060
15
Keyfob button 3 option
6061
0
reserved
6062
123
For the users 04 to 250 the same options as for user 03 can be programmed with the same
number of addresses for each option:
–
Authority level: 1 address each
–
Area selection: 4 addresses each
–
Macro play right: 1 addresses each
–
User code: 6 addresses each
–
Keyfob RFID: 9 addresses each
–
Keyfob button 3 option: 1 address each
The default values for user 04 to 250 are the same as the default values of user 03.
The following addresses are used for programming the users 04 to 250:
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
124
en | Address programming
AMAX panel
User no.
Address
User no.
Address
User no.
Address
04
6063 - 6085
37
6822 - 6844
70
7581 - 7603
05
6086 - 6108
38
6845 - 6867
71
7604 - 7626
06
6109 - 6131
39
6868 - 6889
72
7627 - 7649
07
6132 - 6154
40
6891 - 6913
73
7650 - 7672
08
6155 - 6177
41
6914 - 6936
74
7673 - 7695
09
6178 - 6200
42
6937 - 6959
75
7696 - 7718
10
6201 - 6223
43
6960 - 6982
76
7719 - 7741
11
6224 - 6246
44
6983 - 7005
77
7742 - 7764
12
6247 - 6269
45
7006 - 7028
78
7765 - 7787
13
6270 - 6292
46
7029 - 7051
79
7788 - 7810
14
6293 - 6315
47
7052 - 7074
80
7811 - 7833
15
6316 - 6338
48
7075 - 7097
81
7834 - 7856
16
6339 - 6361
49
7098 - 7120
82
7857 - 7879
17
6362 - 6384
50
7121 - 7143
83
7880 - 7902
18
6385 - 6407
51
7144 - 7166
84
7903 - 7925
19
6408 - 6430
52
7167 - 7189
85
7926 - 7948
20
6431 - 6453
53
7190 - 7212
86
7949 - 7971
21
6454 - 6476
54
7213 - 7235
87
7972 - 7994
22
6477 - 6499
55
7236 - 7258
88
7995 - 8017
23
6500 - 6522
56
7259 - 7281
89
8018 - 8040
24
6523 - 6545
57
7282 - 7304
90
8041 - 8063
25
6546 - 6568
58
7305 - 7327
91
8064 - 8086
26
6569 - 6591
59
7328 - 7350
92
8087 - 8109
27
6592 - 6614
60
7351 - 7373
93
8110 - 8132
28
6615 - 6637
61
7374 - 7396
94
8133 - 8155
29
6638 - 6660
62
7397 - 7419
95
8156 - 8178
30
6661 - 6683
63
7420 - 7442
96
8179 - 8201
31
6684 - 6706
64
7443 - 7465
97
8202 - 8224
32
6707 - 6729
65
7466 - 7488
98
8225 - 8247
33
6730 - 6752
66
7489 - 7511
99
8248 - 8270
34
6753 - 6775
67
7512 - 7534
100
8271 - 8293
35
6776 - 6798
68
7535 - 7557
101
8294 - 8316
36
6799 - 6821
69
7558 - 7580
102
8317 - 8339
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
Address programming | en
AMAX panel
125
User no.
Address
User no.
Address
User no.
Address
103
8340 - 8362
136
9099 - 9121
169
9858 - 9880
104
8363 - 8385
137
9122 - 9144
170
9881 - 9903
105
8386 - 8408
138
9145 - 9167
171
9904 - 9926
106
8409 - 8431
139
9168 - 9190
172
9927 - 9949
107
8432 - 8454
140
9191 - 9213
173
9950 - 9972
108
8455 - 8477
141
9214 - 9236
174
9973 - 9995
109
8478 - 8450
142
9237 - 9259
175
9996 - 10018
110
8501 - 8523
143
9260 - 9282
176
10019 - 10041
111
8524 - 8546
144
9283 - 9305
177
10042 - 10064
112
8547 - 8569
145
9306 - 9328
178
10065 - 10087
113
8570 - 8592
146
9329 - 9351
179
10088 - 10110
114
8593 - 8615
147
9352 - 9374
180
10111 - 10133
115
8616 - 8638
148
9375 - 9397
181
10134 - 10156
116
8639 - 8661
149
9398 - 9420
182
10157 - 10179
117
8662 - 8684
150
9421 - 9443
183
10180 - 10202
118
8685 - 8707
151
9444 - 9466
184
10203 - 10225
119
8708 - 8730
152
9467 - 9489
185
10226 - 10248
120
8731 - 8753
153
9490 - 9512
186
10249 - 10271
121
8754 - 8776
154
9513 - 9535
187
10272 - 10294
122
8777 - 8799
155
9536 - 9558
188
10295 - 10317
123
8800 - 8822
156
9559 - 9581
189
10318 - 10340
124
8823 - 8845
157
9582 - 9604
190
10341 - 10363
125
8846 - 8868
158
9605 - 9627
191
10364 - 10386
126
8869 - 8891
159
9628 - 9650
192
10387 - 10409
127
8892 - 8914
160
9651 - 9673
193
10410 - 10432
128
8915 - 8937
161
9674 - 9696
194
10433 - 10455
129
8938 - 8960
162
9697 - 9719
195
10456 - 10478
130
8961 - 8983
163
9720 - 9742
196
10479 - 10501
131
8984 - 9006
164
9743 - 9765
197
10502 - 10524
132
9007 - 9029
165
9766 - 9788
198
10525 - 10547
133
9030 - 9052
166
9789 - 9811
199
10548 - 10570
134
9053 - 9075
167
9812 - 9834
200
10571 - 10593
135
9076 - 9098
168
9835 - 9857
201
10594 - 10616
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
126
en | Address programming
8.3.2
8.3.3
AMAX panel
User no.
Address
User no.
Address
User no.
Address
202
10617 - 10639
219
11008 - 11030
236
11399 - 11421
203
10640 - 10662
220
11031 - 11053
237
11422 - 11444
204
10663 - 10685
221
11054 - 11076
238
11445 - 11467
205
10686 - 10708
222
11077 - 11099
239
11468 - 11490
206
10709 - 10731
223
11100 - 11122
240
11491 - 11513
207
10732 - 10754
224
11123 - 11145
241
11514 - 11536
208
10755 - 10777
225
11146 - 11168
242
11537 - 11559
209
10778 - 10780
226
11169 - 11191
243
11560 - 11582
210
10801 - 10823
227
11192 - 11214
244
11583 - 11605
211
10824 - 10846
228
11215 - 11237
245
11606 - 11628
212
10847 - 10869
229
11238 - 11260
246
11629 - 11651
213
10870 - 10892
230
11261 - 11283
247
11652 - 11674
214
10893 - 10915
231
11284 - 11306
248
11675 - 11697
215
10916 - 10938
232
11307 - 11329
249
11698 - 11720
216
10939 - 10961
233
11330 - 11352
250
11721 - 11743
217
10962 - 10984
234
11353 - 11375
218
10985 - 11007
235
11376 - 11398
Installer code programming
Option
Address
Default
Installer code
1644 - 1649
123456
Option
Address
Default
Code length (4 - 6 = 4 - 6 digits, 15 = code is not used)
1643
4
Code length programming
The code length is always the same for the user and for the installer code.
8.3.4
Code permission programming
Tamper reset by user
Option
Address
Default
Tamper reset by User (0 = disabled, 1 = enabled)
1601
1
Option
Address
Default
Arm/disarm installer (0 = disabled, 1 = enabled)
1602
1
Arm/disarm installer
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Address programming | en
127
Date / time master user
8.3.5
8.3.6
Option
Address
Default
Date / time master user (0 = disabled, 1 = enabled)
1713
1
Option
Address
Default
Force code change (0 = disabled, 1 = enabled)
1710
0
Force code change
Macro programming
Macro no.
Option
Address
Default
1
Level 1 access (quick play macro) (0 = disabled,
1616
0
Macro recording timeout (seconds)
1617 - 1618
60
Macro play pause time (unit: x100ms)
1619 - 1620
03
Code inside macro* (0 = disabled, 1 = enabled)
1621
1
Macro data length**
1622 - 1624
00
Level 1 access (quick play macro)
1625
0
Macro recording timeout
1626 - 1627
60
Macro play pause time
1628 - 1629
03
Code inside macro*
1630
1
Macro data length**
1631 - 1633
00
Level 1 access (quick play macro)
1634
0
Macro recording timeout
1635 - 1636
60
Macro play pause time
1637 - 1638
03
Code inside macro*
1639
1
Macro data length**
1640 - 1642
00
1 = enabled)
2
3
* This function is relevant only if the macro without code function is disabled.
** This function can not be changed via the programming menu, only via address programming
or via A-Link Plus.
8.4
Zone programming
8.4.1
Add/delete zone programming
AMAX 4000 supports up to 64 zones, 16 keypads and 16 areas.
AMAX 3000 / 3000 BE support up to 32 zones, 8 keypads and 8 areas.
AMAX 2100 supports up to 8 zones, 4 keypads and 2 areas.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
128
en | Address programming
AMAX panel
Zone Module Selection
Zone no.
Address
Default
Zone no.
Address
Default
01
1432
0
05
1436
0
02
1433
0
06
1437
0
03
1434
0
07
1438
0
04
1435
0
08
1439
0
Value range: 0 = onboard zone, 3 = RF all, 4 = RF RFGB glassbreak, 5 = RF RFUN no magnet,
15 = not used
Zone no.
Address
Default
Zone no.
Address
Default
09
1440
0
13
1444
0
10
1441
0
14
1445
0
11
1442
0
15
1446
0
12
1443
0
16
1447
0
Value range: 0 = onboard zone (AMAX 4000), 2 = DX2010 zone, 3 = RF all, 4 = RF RFGB
glassbreak, 5 = RF RFUN no magnet, 15 = not used
Zone no.
Address
Default
Zone no.
Address
Default
17
1448
15
25
1456
15
18
1449
15
26
1457
15
19
1450
15
27
1458
15
20
1451
15
28
1459
15
21
1452
15
29
1460
15
22
1453
15
30
1461
15
23
1454
15
31
1462
15
24
1455
15
32
1463
15
Value range: 1 = Keypad zone (zones 17 to 32 are dedicated to keypad 1 to 16), 2 = DX2010
zone, 3 = RF all, 4 = RF RFGB glassbreak, 5 = RF RFUN no magnet, 15 = not used
Zone no.
Address
Default
Zone no.
Address
Default
33
1464
0
49
1480
0
34
1465
0
50
1481
0
35
1466
0
51
1482
0
36
1467
0
52
1483
0
37
1468
0
53
1484
0
38
1469
0
54
1485
0
39
1470
0
55
1486
0
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Address programming | en
40
1471
0
56
1487
0
41
1472
0
57
1488
0
42
1473
0
58
1489
0
43
1474
0
59
1490
0
44
1475
0
60
1491
0
45
1476
0
61
1492
0
46
1477
0
62
1493
0
47
1478
0
63
1494
0
48
1479
0
64
1495
0
129
Value range: 2 = DX2010 zone, 3 = RF all, 4 = RF RFGB glassbreak, 5 = RF RFUN no magnet,
15 = not used
Notice!
When a zone is assigned to an RF device (3), then the dedicated on-board zone is not
available.
Notice!
AMAX 2100 only: when keypad zones (1-4) are used, onboard zones (5-8) are disabled.
Notice!
Zones may be indicated on keypads with a number that differs from the zone number used for
programming and hardware input: Zones are indicated on LED/LCD keypads according to the
zone numbers. When one zone is disabled the indication number of all following (higher) zone
numbers will shift to a value decreased by one.
Examples:
AMAX 3000 / 3000 BE / 4000:
In a one area or area 1 system keypad the zone number 17 is indicated on a 16 zone LED/LCD
keypad. After disabling zone 16 (or another one in range 1 to 16), zone number 17 is indicated
on the LED/LCD keypad as zone number 16.
AMAX 2100:
In a one area system keypad the zone number 17 is indicated on an 8 zone LED/LCD keypad.
After disabling zone 5, zone number 17 is indicated on the LED/LCD keypad as zone number
5.
Zone function selection
Zone no.
Address
Default
Zone no.
Address
Default
01
1368
3
33
1400
0
02
1369
1
34
1401
0
03
1370
1
35
1402
0
04
1371
1
36
1403
0
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
130
en | Address programming
AMAX panel
05
1372
1
37
1404
0
06
1373
1
38
1405
0
07
1374
1
39
1406
0
08
1375
1
40
1407
0
09
1376
0
41
1408
0
10
1377
0
42
1409
0
11
1378
0
43
1410
0
12
1379
0
44
1411
0
13
1380
0
45
1412
0
14
1381
0
46
1413
0
15
1382
0
47
1414
0
16
1383
0
48
1415
0
17
1384
0
49
1416
0
18
1385
0
50
1417
0
19
1386
0
51
1418
0
20
1387
0
52
1419
0
21
1388
0
53
1420
0
22
1389
0
54
1421
0
23
1390
0
55
1422
0
24
1391
0
56
1423
0
25
1392
0
57
1424
0
26
1393
0
58
1425
0
27
1394
0
59
1426
0
28
1395
0
60
1427
0
29
1396
0
61
1428
0
30
1397
0
62
1429
0
31
1398
0
63
1430
0
32
1399
0
64
1431
0
Value range: 0 - 15
For an explanation of the zone functions, refer to Add / delete zone, page 59.
Zone area selection
Zone no.
Address
Default
Zone no.
Address
Default
01
1240 - 1241
01
33
1304 - 1305
0
02
1242 - 1243
01
34
1306 - 1307
0
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
Address programming | en
AMAX panel
03
1244 - 1245
01
35
1308 - 1309
0
04
1246 - 1247
01
36
1310 - 1311
0
05
1248 - 1249
01
37
1312 - 1313
0
06
1250 - 1251
01
38
1314 - 1315
0
07
1252 - 1253
01
39
1316 - 1317
0
08
1254 - 1255
01
40
1318 - 1319
0
09
1256 - 1257
01
41
1320 - 1321
0
10
1258 - 1259
01
42
1322 - 1323
0
11
1260 - 1261
01
43
1324 - 1325
0
12
1262 - 1263
01
44
1326 - 1327
0
13
1264 - 1265
01
45
1328 - 1329
0
14
1266 - 1267
01
46
1330 - 1331
0
15
1268 - 1269
01
47
1332 - 1333
0
16
1270 - 1271
01
48
1334 - 1335
0
17
1272 - 1273
0
49
1336 - 1337
0
18
1274 - 1275
0
50
1338 - 1339
0
19
1276 - 1277
0
51
1340 - 1341
0
20
1278 - 1279
0
52
1342 - 1343
0
21
1280 - 1281
0
53
1344 - 1345
0
22
1282 - 1283
0
54
1346 - 1347
0
23
1284 - 1285
0
55
1348 - 1349
0
24
1286 - 1287
0
56
1350 - 1351
0
25
1288 - 1289
0
57
1352 - 1353
0
26
1290 - 1291
0
58
1354 - 1355
0
27
1292 - 1293
0
59
1356 - 1357
0
28
1294 - 1295
0
60
1358 - 1359
0
29
1296 - 1297
0
61
1360 - 1361
0
30
1298 - 1299
0
62
1362 - 1363
0
31
1300 - 1301
0
63
1364 - 1365
0
32
1302 - 1303
0
64
1366 - 1367
0
131
Value range: 00 = zone not used, 1 - 16 = area 1 - 16
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
132
en | Address programming
AMAX panel
Zone name programming
Zone no.
Address
Default
Zone no.
Address
Default
1
2952 - 2987
0
33
4104 - 4139
0
2
2988 - 3023
0
34
4140 - 4175
0
3
3024 - 3059
0
35
4176 - 4211
0
4
3060 - 3095
0
36
4212 - 4247
0
5
3096 - 3131
0
37
4248 - 4283
0
6
3132 - 3167
0
38
4284 - 4319
0
7
3168 - 3203
0
39
4320 - 4355
0
8
3204 - 3239
0
40
4356 - 4391
0
9
3240 - 3275
0
41
4392 - 4427
0
10
3276 - 3311
0
42
4428 - 4465
0
11
3312 - 3347
0
43
4464 - 4499
0
12
3348 - 3383
0
44
4500 - 4535
0
13
3384 - 3419
0
45
4536 - 4571
0
14
3420 - 3455
0
46
4572 - 4607
0
15
3456 - 3491
0
47
4608 - 4643
0
16
3492 - 3527
0
48
4644 - 4979
0
17
3528 - 3563
0
49
4680 - 4715
0
18
3564 - 3599
0
50
4716 - 4751
0
19
3600 - 3635
0
51
4752 - 4787
0
20
3636 - 3671
0
52
4788 - 4823
0
21
3672 - 3707
0
53
4824 - 4859
0
22
3708 - 3743
0
54
4860 - 4895
0
23
3744 - 3779
0
55
4896 - 4931
0
24
3780 - 3815
0
56
4932 - 4967
0
25
3816 - 3851
0
57
4968 - 5003
0
26
3852 - 3887
0
58
5004 - 5039
0
27
3888 - 3923
0
59
5040 - 5075
0
28
3924 - 3959
0
60
5076 - 5111
0
29
3960 - 3995
0
61
5112 - 5147
0
30
3996 - 4031
0
62
5148 - 5183
0
31
4032 - 4067
0
63
5184 - 5219
0
32
4068 - 4103
0
64
5220 - 5255
0
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Address programming | en
133
How to insert alphabetical characters via address programming
–
A character needs two values to provide input to two addresses.
–
Determine these values using the matrix of table below.
–
Every character in this table has a row index and also a column index.
–
Row index is the first, and column index is the second value for each character.
0
2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
!
"
#
$
%
&
'
(
)
*
+
-
,
.
/
3
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
4
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
5
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
6
‛
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
7
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
8
đ
Ą
ᶏ
Ł
Ğ
..
Ć
Ś
Ű
Ş
İ
Ź
Ę
ź
Ż
9
Ń
ń
Č
ł
ǧ
¨
ć
ś
ű
č
ş
I
Ț
ę
ţ
ż
10
á
ɨ
¢
£
€
¥
Š
§
š
©
ª
«
¬
‫־‬
®
¯
11
°
±
²
³
Ž
µ
¶
•
ž
¹
°
»
Œ
œ
Ÿ
¿
12
À
Á
Â
Ã
Ä
Å
Æ
Ç
È
É
Ê
Ë
Ì
Í
Î
Ï
13
Đ
Ñ
Ò
Ó
Ô
Õ
Ö
×
Ø
Ù
Ú
Û
Ü
Ý
Þ
ß
14
à
á
â
ã
ä
å
æ
ç
è
é
ê
ë
ì
í
î
ï
15
ð
ñ
ò
ó
ô
ô
ö
÷
ø
ù
ú
û
ü
ý
þ
ÿ
Table 8.1: Characters
Example
A = 4 1, A = Address 3736 = 4, Address 3737 = 1
o = 6 15, k = 6 11
8.4.2
Zone function programming
Zone function
Option
Address
Default
00
Selection of a zone type (00 - 26)*
1000 - 1001
00
Allow bypass/force arm (0 = disabled, 1 = allow
1002
3
force alarm, 2 = allow bypass, 3 = allow both)
Silent alarm/chime mode (0 = disabled, 1 = silent
VDS-A
EN=0/2
1003
alarm, 2 = chime mode, 3 = both)
0
VDS-A
EN=0/2
Pulse count (0 = disabled, 1 - 9 = 1 - 9 times)
1004
0
Zone lockout (0 = disabled, 1 = 1 time, 2 = 3
1005
3
VDS-A EN=0
times, 3 = 6 times, 4 = alarm duration)
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
134
en | Address programming
AMAX panel
Zone DEOL (0 = EOL, 1 = DEOL, 2 = reserved, 3 =
1006
1
1007
6
NC, 4 = NO) (3 and 4 are not applicable for
wireless zones)
Report (1 = receiver 1,
2 = receiver 2,
VDS-A
EN=1/5/6/7
3 = receiver 3,
4 = receiver 4,
5 = receiver 1, 2, 3, 4,
6 = receiver 1 (2, 3, 4 backup)
7 = receiver 1 (2 backup) and receiver 3 (4
backup)
8 = receiver 1, 2
9 = receiver 1 (2 backup)
10 = receiver 3, 4
11 = receiver 3 (4 backup))
Cross zone/unverified alarm (0 = disabled, 1 =
1008
0
1009
0
Zone reaction time (unit: x100ms)
1010 - 1013
0003
Trouble domestic (0 = disabled, 1 = enabled)
1014
1
Zone alarm on keypad (0 = disabled, 1 = enabled) 1754
0
Selection of a zone type*
1015 - 1016
01
Allow bypass/force arm
1017
3
VDS-A EN=0
unverified alarm, 2 = cross zone, 3 = both)
Zone domestic call (1 = dom. 1,
2 = dom. 2,
3 = dom. 3,
4 = dom. 4,
5 = dom. 1, 2, 3, 4,
6 = dom. 1 (2, 3, 4 backup)
7 = dom. 1 (2 backup) and dom. 3 (4 backup)
8 = dom. 1, 2
9 = dom. 1 (2 backup)
10 = dom. 3, 4
11 = dom. 3 (4 Backup))
01 (as an
example for the
following zone
VDS-A
EN=0/2
functions 02 to
15)
Silent alarm/chime mode
1018
0
VDS-A
EN=0/2
Pulse count
1019
0
Zone lockout
1020
3
Zone DEOL
1021
1
Report
1022
6
VDS-A EN=0
VDS-A
EN=1/5/6/7
Cross zone/unverified alarm
2016.05 | 08 | F.01U.309.277
Installation Manual
1023
0
VDS-A EN=0
Bosch Sicherheitssysteme GmbH
AMAX panel
Address programming | en
Zone domestic call
1024
0
Zone reaction time
1025 - 1028
0003
Trouble domestic
1029
1
Zone alarm on keypad
1755
0
135
*For an explanation of the zone types, refer to Add / delete zone, page 59.
For the zone functions 02 to 15 the same options as for zone functions 01 can be programmed
with the same number of addresses for each option:
–
Selection of a zone type: 2 addresses each
–
Allow bypass/force arm: 1 address each
–
Silent alarm/chime mode: 1 address each
–
Pulse count: 1 address each
–
Zone lockout: 1 address each
–
Zone DEOL: 1 address each
–
Report: 1 address each
–
Cross zone/unverified alarm: 1 address each
–
Zone domestic call: 1 address each
–
Zone reaction time: 4 addresses each
–
Trouble domestic: 1 address each
The default values for zone functions 02 to 15 are the same as the default values of zone
functions 01, except for the option “Selection of a zone type”.
The following addresses are used for programming the zone functions 02 to 15:
Zone function
Option
Address
Default
02
Selection of a zone type*
1030 - 1031
02
Allow bypass/force arm trouble domestic option
1031 - 104
3003160
as shown above
03
00003
Zone alarm on keypad
1756
0
Selection of a zone type*
1045 - 1046
03
Allow bypass/force arm trouble domestic option
1047 - 1059
3003160
as shown above
04
00003
Zone alarm on keypad
1757
0
Selection of a zone type*
1060 - 1061
04
Allow bypass/force arm trouble domestic option
1062 - 1074
3003160
as shown above
05
00003
Zone alarm on keypad
1758
0
Selection of a zone type*
1075 - 1076
05
Allow bypass/force arm trouble domestic option
1077 - 1089
3003160
as shown above
06
Bosch Sicherheitssysteme GmbH
00003
Zone alarm on keypad
1759
0
Selection of a zone type*
1090 - 1091
06
Installation Manual
2016.05 | 08 | F.01U.309.277
136
en | Address programming
AMAX panel
Allow bypass/force arm trouble domestic option
1092 - 1104
as shown above
07
00003
Zone alarm on keypad
1760
0
Selection of a zone type*
1105 - 1106
07
Allow bypass/force arm trouble domestic option
1107 - 1119
3003160
as shown above
08
00003
Zone alarm on keypad
1761
0
Selection of a zone type*
1120 - 1121
08
Allow bypass/force arm trouble domestic option
1122 - 1134
3003160
as shown above
09
00003
Zone alarm on keypad
1762
0
Selection of a zone type*
1135 - 1136
09
Allow bypass/force arm trouble domestic option
1137 - 1149
3003160
as shown above
10
00003
Zone alarm on keypad
1763
0
Selection of a zone type*
1150 - 1151
10
Allow bypass/force arm trouble domestic option
1152 - 1164
3003160
as shown above
11
00003
Zone alarm on keypad
1764
0
Selection of a zone type*
1165 - 1166
11
Allow bypass/force arm trouble domestic option
1167 - 1179
3003160
as shown above
12
00003
Zone alarm on keypad
1765
0
Selection of a zone type*
1180 - 1181
12
Allow bypass/force arm trouble domestic option
1182 - 1194
3003160
as shown above
13
00003
Zone alarm on keypad
1766
0
Selection of a zone type*
1195 - 1196
13
Allow bypass/force arm trouble domestic option
1197 - 1209
3003160
as shown above
14
00003
Zone alarm on keypad
1767
0
Selection of a zone type*
1210 - 1211
14
Allow bypass/force arm trouble domestic option
1212 - 1224
3003160
as shown above
15
2016.05 | 08 | F.01U.309.277
3003160
00003
Zone alarm on keypad
1768
0
Selection of a zone type*
1225 - 1226
15
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Address programming | en
Allow bypass/force arm trouble domestic option
1227 - 1239
as shown above
137
3003160
00003
Zone alarm on keypad
1769
0
*For an explanation of the zone types, refer to Add / delete zone, page 59.
8.4.3
Pulse count duration programming
Option
Address
Default
Pulse count duration (0 = disabled, 1 - 999 = 1 - 999
1606 - 1608
060
seconds)
8.4.4
VDS-A
EN=000
Zone cross timer programming
Option
Address
Default
Zone cross timer (1 - 999 = 1 - 999 seconds)
1594 - 1596
060
8.5
Keypad and area programming
8.5.1
Keypad area programming
Keypad
Address
Default
no.
Keypad
Address
Default
no.
1
1560 - 1561
01
9
1576 - 1577
99
2
1562 - 1563
99
10
1578 - 1579
99
3
1564 - 1565
99
11
1580 - 1581
99
4
1566 - 1567
99
12
1582 - 1583
99
5
1568 - 1569
99
13
1584 - 1585
99
6
1570 - 1571
99
14
1586 - 1587
99
7
1572 - 1573
99
15
1588 - 1589
99
8
1574 - 1575
99
16
1590 - 1591
99
Value range: 00 = master keypad, 01 - 16 = area 01 - 16, 99 = not used
Notice!
The system supports up to 16 master keypads. When the master keypad is not switched to
the corresponding area, no arming/disarming, bypass and alarm reset operations can be
performed on the master keypad. Operations can only be performed in the area when the
master keypad is switched to the corresponding area.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
138
en | Address programming
8.5.2
AMAX panel
Area timing programming
Exit and entry delay time
Area
Exit Delay
Default
Address
Entry Delay
Default
Entry Delay Default
Address
2 Address
1
0785 - 0787
45
0788 - 0790
30
0791 - 0793 30
2
0794 - 0796
45
0797 - 0799
30
0800 - 0802 30
3 **
0803 - 0805
45
0806 - 0808
30
0809 - 0811 30
4 **
0812 - 0814
45
0815 - 0817
30
0818 - 0820 30
5 **
0821 - 0823
45
0824 - 0826
30
0827 - 0829 30
6 **
0830 - 0832
45
0833 - 0835
30
0836 - 0838 30
7 **
0839 - 0841
45
0842 - 0844
30
0845 - 0847 30
8 **
0848 - 0850
45
0851 - 0853
30
0854 - 0856 30
9*
0857 - 0859
45
0860 - 0862
30
0863 - 0865 30
10 *
0866 - 0868
45
0869 - 0871
30
0872 - 0874 30
11 *
0875 - 0877
45
0878 - 0880
30
0881 - 0883 30
12 *
0884 - 0886
45
0887 - 0889
30
0890 - 0892 30
13 *
0893 - 0895
45
0896 - 0898
30
0899 - 0901 30
14 *
0902 - 0904
45
0905 - 0907
30
0908 - 0910 30
15 *
0911 - 0913
45
0914 - 0916
30
0917 - 0919 30
16 *
0920 - 0922
45
0923 - 0925
30
0926 - 0928 30
000-999 seconds
000-999 seconds, EN=045
000-999 seconds, EN=045
seconds
seconds
* AMAX 4000
** AMAX 3000 / 3000 BE / 4000
Entry and exit delay time audible
Option
Address
Default
Area 1
1714 - 1715
15
Area 2
1716 - 1717
15
Area 3
1718 - 1719
15
(01 = entry time (STAY) for area keypad,
02 = exit time (STAY) for area keypad,
04 = entry time (STAY) for master keypad,
08 = exit time (STAY) for master keypad,
10 = entry time (AWAY) for area keypad,
20 = exit time (AWAY) for area keypad,
40 = entry time (AWAY) for master keypad,
80 = exit time (AWAY) for master keypad)
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
8.5.3
Address programming | en
Area 4
1720 - 1721
15
Area 5
1722 - 1723
15
Area 6
1724 - 1725
15
Area 7
1726 - 1727
15
Area 8
1728 - 1729
15
Area 9
1730 - 1731
15
Area 10
1732 - 1733
15
Area 11
1734 - 1735
15
Area 12
1736 - 1737
15
Area 13
1738 - 1739
15
Area 14
1740 - 1741
15
Area 15
1742 - 1743
15
Area 16
1744 - 1745
15
Option
Address
Default
Common area
1593
0
139
Common area programming
(00 = none,
01 = follow area 2,
02 = follow area 2 - 3,
03 = follow area 2 - 4,
04 = follow area 2 - 5,
06 = follow area 2 - 7,
07 = follow area 2 - 8,
08 = follow area 2 - 9,
09 = follow area 2 - 10,
10 = follow area 2 - 11,
11 = follow area 2 - 12,
12 = follow area 2 - 13,
13 = follow area 2 - 14,
14 = follow area 2 - 15,
15 = follow area 2 - 16)
Notice!
In case of common area, area 1 will be the common area. When there is only one area in the
system, the address for common area programming can only be programmed as 1.
8.5.4
Keypad indication programming
Option
Address
Default
Keypad alarm tone (0 = disabled, 1 = enabled)
0622
1
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
140
en | Address programming
AMAX panel
Alarm indication on keypads (0 = disabled, 1 = STAY
1615
3
Backlight on entry time (0 = disabled, 1 = enabled)
1668
1
Keypad arm LED indication timeout (00 – 99, 00 = always
1682 - 1683
00
1681
2
Master keypad alarm tone (0 = disabled, 1 = enabled)
1680
1
Master keypad back to master mode timeout (00 - 99,
1700 - 1701
60
Option
Address
Default
Follow EN standard
1679
0
Keypad lockout (0 = disabled, 1 - 15 = 1 - 15 times)
1592
armed enabled, 2 = AWAY armed enabled, 3 = both
enabled)
on)
Master keypad LED on (0 = disabled, 1 = 1st area on, 2 =
1st area flash, 3 = all area on, 4 = 1st area on ex, 5 = 1st
area flh ex, 6 = all area on ex)
00=never)
8.5.5
Keypad lockout programming
10
VDS-A
EN=10
8.6
System programming
8.6.1
System setting programming
DST options programming
Option
Address
Default
Auto daylight saving time option (00=disable auto DST,
1746 - 1747
00
01=Europe, 02=Brazil, 03=Mexico, 04=US and north
Mexico, 05=customize DST settings)
Customize start: month (1=January ,2=February, 3=March, 1748
3
4=April, 5=May, 6=June, 7=July, 8=August, 9=September,
10=October, 11=November, 12=December)
Customize start: ordinal (week) (1=1st, 2=2nd, 3=3rd,
1749
5
1750
7
4=4th, 5=last)
Customize start: weekday (1=Monday, 2=Tuesday,
3=Wednesday, 4=Thursday, 5=Friday, 6=Saturday,
7=Sunday)
Customize stop: month (1=January ,2=February, 3=March, 1751
10
4=April, 5=May, 6=June, 7=July, 8=August, 9=September,
10=October, 11=November, 12=December)
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
Address programming | en
AMAX panel
Customize stop: ordinal (week) (1=1st, 2=2nd, 3=3rd,
1752
5
1753
7
Option
Address
Default
AC fault report delay time (99 =disabled, 0 - 98 = 0 - 98
1613 - 1614
141
4=4th, 5=last)
Customize stop: weekday (1=Monday, 2=Tuesday,
3=Wednesday, 4=Thursday, 5=Friday, 6=Saturday,
7=Sunday)
Fault configuration programming
minutes)
60 VDS-A
EN=00-60
Display and prompt tone of date and time fault (0 =
0620
1
Fault prompt tone (0 = disabled, 1= enabled)
0621
1
Battery Check interval (0 =disabled, 1 - 15 = 1 - 15
1612
15
disabled, 1= enabled)
minutes)
VDS-A EN=1
VDS-A
EN=15
Phone line monitor (0 = disabled, 1= enabled)
1599
0
Siren supervision (minutes)
0623 - 0624
00
Siren / PO1+2 Supervision (0 = disabled, 1 = OC1 monitor 1598
0
enabled, 2 = OC2 monitor enabled, 3 = enabled)
AC fault auto reset (0 = disabled, 1= enabled)
1671
0
Communication fault auto reset (0 = disabled, 1=
1672
0
Phone fault auto reset (0 = disabled, 1= enabled)
1673
0
General fault auto reset (0 = disabled, 1= enabled)
1674
0
Option
Address
Default
Quick arming (0 = disabled 1= enabled)
1597
1
Option
Address
Default
Installer access until next arming (0 = disabled, 1 =
1660
0
Option
Address
Default
Remote IP access (0 = disabled, 1 = enabled)
0971
0
enabled)
Quick arm programming
VDS-A EN=0
Installer access until next arming programming
enabled)
Remote IP access programming
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
142
en | Address programming
AMAX panel
Force arm when system is in trouble programming
Option
Address
Default
Force arm when system is in trouble condition (0 =
1611
1
Option
Address
Default
Event record count per set/unset period (3 - 10)
1609
10
Option
Address
Default
Language version of the keypad (0 = default, 1 = EN, 2 =
0996
0
Option
Address
Default
Keypad 2 button alarm (0 = disabled, 1 = enabled)
0992
1
Keypad 2 button panic alarm (0 = disabled, 1 = report, 2 = 0993
1
disabled, 1 = enabled)
Event record count per set/unset period programming
Language Version Programming
DE, 3 = ES, 4 = FR, 5 = IT, 6 = PL, 7 = NL, 8 = SE, 9 = TR)
Keypad 2 button alarm
siren, 3 = all)
Keypad 2 button fire alarm (0 = disabled, 1 = report, 2 =
0994
1
0995
1
Option
Address
Default
System tamper indication in area (0 = area 1, 1 = all
1610
0
1603
1
1675 - 1678
0003
Option
Address
Default
Area 1 name
2596 - 2615
0
Area 2 name
2616 - 2635
0
Area 3 name
2636 - 2655
0
siren, 3 = all)
Keypad 2 button medical alarm (0 = disabled, 1 = report,
2 = siren, 3 = all)
System tamper indication
areas)
Zone tamper bypass when DEOL zone is bypassed (0 =
disabled, 1 = enabled)
Tamper debounce time (unit: x100s)
Area and company name programming
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Address programming | en
Area 4 name
2656 - 2675
0
Area 5 name
2676 - 2695
0
Area 6 name
2696 - 2715
0
Area 7 name
2716 - 2735
0
Area 8 name
2736 - 2755
0
Area 9 name
2756 - 2775
0
Area 10 name
2776 - 2795
0
Area 11 name
2796 - 2815
0
Area 12 name
2816 - 2835
0
Area 13 name
2836 - 2855
0
Area 14 name
2856 - 2875
0
Area 15 name
2876 - 2895
0
Area 16 name
2896 - 2915
0
Company Name
2916 - 2951
0
143
An area or company name may have up to 18 characters. Each character of the area or
company name uses 2 addresses.
How to insert alphabetical characters via address programming
–
A character needs two values to provide input to two addresses.
–
Determine these values using the matrix of table below.
–
Every character in this table has a row index and also a column index.
–
Row index is the first, and column index is the second value for each character.
0
2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
!
"
#
$
%
&
'
(
)
*
+
-
,
.
/
3
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
4
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
5
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
6
‛
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
7
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
8
đ
Ą
ᶏ
Ł
Ğ
..
Ć
Ś
Ű
Ş
İ
Ź
Ę
ź
Ż
9
Ń
ń
Č
ł
ǧ
¨
ć
ś
ű
č
ş
I
Ț
ę
ţ
ż
10
á
ɨ
¢
£
€
¥
Š
§
š
©
ª
«
¬
‫־‬
®
¯
11
°
±
²
³
Ž
µ
¶
•
ž
¹
°
»
Œ
œ
Ÿ
¿
12
À
Á
Â
Ã
Ä
Å
Æ
Ç
È
É
Ê
Ë
Ì
Í
Î
Ï
13
Đ
Ñ
Ò
Ó
Ô
Õ
Ö
×
Ø
Ù
Ú
Û
Ü
Ý
Þ
ß
14
à
á
â
ã
ä
å
æ
ç
è
é
ê
ë
ì
í
î
ï
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
144
en | Address programming
15
AMAX panel
ð
ñ
ò
ó
ô
ô
ö
÷
ø
ù
ú
û
ü
ý
þ
ÿ
Table 8.2: Characters
Example
A = 4 1, A = Address 3736 = 4, Address 3737 = 1
o = 6 15, k = 6 11
8.6.2
System factory default programming
Factory default pads enable
Option
Address
Default
Factory default pads (0 = disable, 1 = enabled)
1604
1
8.7
Output and siren programming
8.7.1
Output programming
Output no.
Available for module
Available on panel
01 - 03
On-board output
AMAX 2100 / 3000 / 3000 BE / 4000
04
On-board output
AMAX 3000 BE / 4000
05 - 12
DX3010 module 1 output
AMAX 2100 / 3000 / 3000 BE / 4000
13 - 20
DX3010 module 2 output
AMAX 3000 / 3000 BE / 4000
Output no.
Option
Address
Default
01
Output event type 1 (00-36)*
0625 - 0626
05
Output area/zone no. 1
0627 - 0628
00
Output mode 1 (0 = continuous, 1 = pulse, 3 =
0629
0
Output time 1 (seconds)
0630 - 0632
180
Output event type 2 (00-36)*
13164 - 13165
00
Output area/zone no. 2
13166 - 13167
00
Output mode 2 (0 = continuous, 1 = pulse, 3 =
13168
0
Output time 2 (seconds)
13169 - 13171
000
Output event type 3 (00-36)*
13172 - 13173
00
Output area/zone no. 3
13174 - 13175
00
Output mode 3 (0 = continuous, 1 = pulse, 3 =
13176
0
Output time 3 (seconds)
13177 - 13179
000
Output event type 1
0633 - 0634
05
continuous inverted)
continuous inverted)
continuous inverted)
02
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Address programming | en
03
04
Bosch Sicherheitssysteme GmbH
Output area/zone no. 1
0635 - 0636
00
Output mode 1
0637
0
Output time 1
0638 - 0640
000
Output event type 2
13180 - 13181
00
Output area/zone no. 2
13182 - 13183
00
Output mode 2
13184
0
Output time 2
13185 - 13187
000
Output event type 3
13188 - 13189
00
Output area/zone no. 3
13190 - 13191
00
Output mode 3
13192
0
Output time 3
13193 - 13195
000
Output event type 1
0641 - 0642
05
Output area/zone no. 1
0643 - 0644
00
Output mode 1
0645
0
Output time 1
0646 - 0648
180
Output event type 2
13196 - 13197
00
Output area/zone no. 2
13198 - 13199
00
Output mode 2
13200
0
Output time 2
13201 - 13203
000
Output event type 3
13204 - 13205
00
Output area/zone no. 3
13206 - 13207
00
Output mode 3
13208
0
Output time 3
13209 - 13211
000
Output event type 1
0649 - 0650
07
Output area/zone no. 1
0651 - 0652
00
Output mode 1
0653
0
Output time 1
0654 - 0656
180
Output event type 2
13212 - 13213
00
Output area/zone no. 2
13214 - 13215
00
Output mode 2
13216
0
Output time 2
13217 - 13219
000
Output event type 3
13220 - 13221
00
Output area/zone no. 3
13222 - 13223
00
Output mode 3
13224
0
Installation Manual
145
2016.05 | 08 | F.01U.309.277
146
en | Address programming
AMAX panel
05 (as an
example for the
following
outputs 06 to
20)
Output time 3
13225 - 13227
000
Output event type 1
0657 - 0658
00
Output area/zone no. 1
0659 - 0660
00
Output mode 1
0661
0
Output time 1
0662 - 0664
000
Output event type 2
13228 - 13229
00
Output area/zone no. 2
13230 - 13231
00
Output mode 2
13232
0
Output time 2
13233 - 13235
000
Output event type 3
13236 - 13237
00
Output area/zone no. 3
13238 - 13239
00
Output mode 3
13240
0
Output time 3
13241 - 13243
000
* For an explanation of the output events, refer to , page 85 in chapter Outputs, page 85.
For the outputs 06 to 20 the same options as for output 05 can be programmed with the same
number of addresses for each of the three output options.
–
Output event: 2 addresses each
–
Output area/zone no.: 2 addresses each
–
Output mode: 1 address each
–
Output time: 3 addresses each
The default values for outputs 06 to 20 are the same as the default values of output 05.
The following addresses are used for programming the outputs 06 to 20 with three output
event types each:
Output no.
Address
Output no. Address
Output no. Address
06
0665 - 0672
11
16
07
08
09
2016.05 | 08 | F.01U.309.277
0705 - 0712
0745 - 0752
13244 - 13251
13324 - 13331
13404 - 13411
13252 - 13259
13332 - 13339
13412 - 13419
0673 - 0680
12
0713 - 0720
17
0753 - 0760
13260 - 13267
13340 - 13347
13420 - 13427
13268 - 13275
13348 - 13355
13428 - 13435
0681 - 0688
13
0721 - 0728
18
0761 - 0768
13276 - 13283
13356 - 13363
13436 - 13443
13284 - 13291
13364 - 13371
13444 - 13451
0689 - 0696
14
0729 - 0736
19
0769 - 0776
13292 - 13299
13372 - 13379
13452 - 13459
13300 - 13307
13380 - 13387
13460 - 13467
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Address programming | en
10
0697 - 0704
15
0737 - 0744
20
147
0777 - 0784
13308 - 13315
13388 - 13395
13468 - 13475
13316 - 13323
13396 - 13403
13476 - 13483
Notice!
When the zone activating alarm is programmed as a silent alarm, keypad and audible alarm
have no output.
8.7.2
Siren programming
Option
Address
Default
Beep for warning devices (0 = disabled, 1 = enabled)
1600
1
Internal siren beep as indication (0 = disabled, 1 =
1611
0
1605
1
Option
Address
Default
Printer functionality (0 = disabled, 1= enabled)
0991
0
RF receiver functionality (0 = disabled, 1= enabled)
0948
0
RF supervision interval (0 = disabled, 1 = 20 min, 2 = 1h, 3 0949
4
enabled)
Silence warning device when disarmed (0 = disabled, 1 =
enabled)
8.8
RF device programming
RF Options
EN=2
= 2h, 4 = 4h, 5 = 12 h, 6 = 24h)
RF jam detect level (00 - 15, 00 = disabled, 01 = most
0950
12
0951
2
0952
1
0953
0
0954
1
sensitive, 15 = least sensitive)
RF device low level battery resound (0 = disabled, 1 = 4h,
2 = 24h)
Siren beep arm/disarm (RF keyfob) (0 = disabled, 1=
enabled)
Keyfob panic option (0 = no alarm, 1 = silent alarm, 2 =
sound alarm)
RF missing as alarm (0 = disabled, 1= enabled)
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
148
en | Address programming
AMAX panel
Wireless zone RFID
RFID for
Default
RFID for
wireless
Address
(ten
wireless
Address
Default
(ten
zone no.
digits, 15
zone no
digits, 15
= not in
= not in
use)
use)
1
5256 - 5265
15
33
5576 - 5585
15
2
5266 - 5275
15
34
5586 - 5595
15
3
5276 - 5285
15
35
5596 - 5605
15
4
5286 - 5295
15
36
5606 - 5615
15
5
5296 - 5305
15
37
5616 - 5625
15
6
5306 - 5315
15
38
5626 - 5635
15
7
5316 - 5325
15
39
5636 - 5645
15
8
5326 - 5335
15
40
5646 - 5655
15
9
5336 - 5345
15
41
5656 - 5665
15
10
5346 - 5355
15
42
5666 - 5675
15
11
5356 - 5365
15
43
5676 - 5685
15
12
5366 - 5375
15
44
5686 - 5695
15
13
5376 - 5385
15
45
5696 - 5705
15
14
5386 - 5395
15
46
5706 - 5715
15
15
5396 - 5405
15
47
5716 - 5725
15
16
5406 - 5415
15
48
5726 - 5735
15
17
5416 - 5425
15
49
5736 - 5745
15
18
5426 - 5435
15
50
5746 - 5755
15
19
5436 - 5445
15
51
5756 - 5765
15
20
5446 - 5455
15
52
5766 - 5775
15
21
5456 - 5465
15
53
5776 - 5785
15
22
5466 - 5475
15
54
5786 - 5795
15
23
5476 - 5485
15
55
5796 - 5805
15
24
5486 - 5495
15
56
5806 - 5815
15
25
5496 - 5505
15
57
5816 - 5825
15
26
5506 - 5515
15
58
5826 - 5835
15
27
5516 - 5525
15
59
5836 - 5845
15
28
5526 - 5535
15
60
5846 - 5855
15
29
5536 - 5545
15
61
5856 - 5865
15
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Address programming | en
30
5546 - 5555
15
62
5866 - 5875
15
31
5556 - 5565
15
63
5876 - 5885
15
32
5566 - 5575
15
64
5886 - 5895
15
149
Wireless repeater RFID
RFID for wireless
Address
repeater no.
Bosch Sicherheitssysteme GmbH
Default (ten digits,
15 = not in use)
1
5896 - 5905
15
2
5906 - 5915
15
3
5916 - 5925
15
4
5926 - 5935
15
5
5936 - 5945
15
6
5946 - 5955
15
7
5956 - 5965
15
8
5966 - 5975
15
Installation Manual
2016.05 | 08 | F.01U.309.277
150
en | Troubleshooting
AMAX panel
9
Troubleshooting
9.1
General trouble
Problem
Reason
No display on the keypad
–
after power up
–
Solution
AC power or battery fuse –
Check if the AC power
failure
and battery fuses are
Abnormal RBGY wiring
properly connected and
operate normally
–
Reconnect RBGY
No response to the keypad
–
Abnormal RBGY wiring
–
Reconnect RBGY
operation (wrong tone
–
The keypad is locked
–
Operate after 3 minutes
after many times of
–
Set the jumper again
sounds on pressing any key).
–
wrong passwords are
referring to the
entered
information on keypad
Wrong jumper when
address settings
multiple keypads are
used
Constant on of the zone
–
Wrong zone wiring
indicator.
–
Abnormal detector
–
Fault indicator constant on /
–
flash
–
again
function
–
Reset the detector
Zone EOL resistor is not
–
Correctly connect the
correctly connected to
zone EOL resistor to the
the end of the detector
end of the detector
Date and time fault
–
Set date and time
displayed in
–
Connect the battery or
programming although
resume the voltage of
date and time are not set
–
–
–
–
–
Backup battery is not
the battery to over 12V
–
Connect the alarm siren
connected or the voltage
(with the alarm siren
of the battery connected
substituted by a resistor
is lower than 12V
of 1K)
Alarm siren is not
–
Correctly set the
connected
telephone number again
The telephone number is –
Connect the telephone
incorrectly set
network
Telephone network is
–
Connect the tamper
not connected
switch or the short
The tamper switch is not
circuit jumper
connected
–
Enter zone wiring once
–
Connect modules for
External module should
programming such as
be used for
DX2010, DX3010, B426,
programming, but it not
or ITS-DX4020-G
actually connected
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Troubleshooting | en
No response from the zone
–
To ensure normal
for a short time after power
operation, the system
up
should be left alone for a
151
–
Operate after 1 minute
–
Check if the 18V of the
minute after power up
AC power fault
–
AC power fuse is burnt.
transformer is correctly
wired and replace the
fuse
Over current protection of the –
Abnormal wiring of the
auxiliary power
12V auxiliary power
–
The auxiliary power
–
Reconnect the auxiliary
power
–
Use external power
exceeds the power
supply for perimeter
supply upper limit for the
devices
AMAX panel
The auxiliary power cannot be –
AC power and battery
recovered after short circuit
fail
Failure of battery is still
–
The battery might be
–
Power up AC power and
battery again
–
The fault will be
displayed after the battery is
tested 4 hours after the
automatically cleared
replaced
system is armed each
when the system is reset
time
or the battery is re-
The voltage of the
tested
battery is lower than 12V –
Charge the new battery
–
for a period of time until
the voltage reaches 12V
or above
Not entering programming
–
mode after power up
–
The red LED on the main
–
board goes off
The system is in alarm
–
Reset the alarm
state
–
Disarm the system and
The system is in arming
keep it in the disarming
state
status
Abnormal AC power and
–
backup battery
The system does not dial
Check AC power and
backup battery
–
The main board fails
–
Replace the main board
–
Relevant receiver
–
Correctly set the
when the alarm presents.
parameters are not set
telephone number, set
transmission format to
CID and set zone alarm
to corresponding paths
Remote telephone arming fail
–
The remote telephone
–
arming is disabled (the
0144 to a number from 1
address 0144 is set to 0)
–
There are multiple areas
in the system
Program the address
to 15
–
The telephone arming is
available when the
system has area 1 only
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
152
en | Troubleshooting
AMAX panel
RPS cannot perform remote
–
programming and control
Both addresses 0144
–
and 0145 are set to 0
Program the address
0144 to a number from 1
to 15. Program the
address 0145 to 1
Occasionally abnormal
–
communication in use of
Contact ID/personal
–
telephone alarm
Extension system is used –
Add dial delay in
in the telephone network
programming
The telephone network
–
support ADSL as well
No response from the keypad
–
and the alarm siren
The zone silent alarm is
Connect the system after
the ADSL filter
–
enabled
Disable the zone silent
alarm
(disabled) when an alarm is
triggered by the zone
The AMAX panel cannot send
–
The transmission format
–
Program the
any reports (programmed to
of the receiver is
transmission format of
send reports to receiver)
programmed to 0 = not
the receiver to 1 or 3
used
A-LINK cannot be connected
–
with ITS- DX4020-G
–
The parameters of
–
Recommend to set the
DX4020-G module are
parameter ACK TIMEOUT
not properly set.
of DX4020-G module to
The option Specific
the maximum (600) and
network is not selected
set TRANSMIT BUFFER
for an IP remote
LIFE TIME to the
connection if a DX4020G module is used.
maximum (120)
–
Select the option
Specific network for an
IP remote connection if a
DX4020-G module is
used.
9.2
Trouble fault inquiry
Fault Inquiry
Faults and tampers can be displayed via the fault analysis function. For more information refer
to System view, page 83.
The following faults and tampers are possible:
Lit number indicators
First
Second
Third
1
Accessory module failure
1
1
1
1
1
2
1
2
1
3
2016.05 | 08 | F.01U.309.277
Description of the fault or tamper
Network/IP module 1 failure
1-2
Network/IP module 1 - 2 failure
Output expansion module failure
1-2
Output expansion module 1 – 2 fault
Input expansion module failure
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Troubleshooting | en
1
3
1-6
1
4
1
4
1
Module DX4010 missing
1
4
2
Printer missing
1
4
3
Printer fault
1
5
1
5
1
RF receiver 1 fault
1
5
2
RF receiver 1 missing
1
5
3
RF receiver 1 jammed
1
6
1
6
1
RF sensor missing*
1
6
2
RF sensor fault*
1
7
1
7
1
8
1
8
1
Configuration conflict sensors*
1
8
2
Configuration conflict repeaters*
1
8
3
Configuration conflict keyfobs*
Input expansion module 1 - 6 failure
Printer failure
RF receiver failure
RF sensor failure
RF repeater failure
1–8
RF repeater 1 – 8 missing
RF config failure
2
Power failure
2
1
Panel AC failure
2
2
Panel low battery
2
3
Panel Aux power failure
2
3
2
4
2
4
2
5
2
5
2
6
2
6
2
7
RF sensor power failure*
2
8
RF keyfob battery failure*
3
1-2
Panel Aux power 1 – 2 fault
Bosch option bus power failure
1-2
Bosch option bus 1 – 2 power fault
RF repeater AC power failure
1-8
RF repeater 1 – 8 AC power fault
RF repeater battery failure
1–8
RF repeater 1 – 8 battery fault
Output failure
3
1
Onboard output 1 fault
3
2
Onboard output 2 fault
Bosch Sicherheitssysteme GmbH
153
Installation Manual
2016.05 | 08 | F.01U.309.277
154
en | Troubleshooting
AMAX panel
4
4
Keypad failure
1 - 16
Keypad 1 – 16 failure
5
5
System failure
1
Date time not set
6
Communication failure
6
1
Communication fault 1
6
2
Communication fault 2
6
3
Communication fault 3
6
4
Communication fault 4
6
5
Phone line fault
7
Tamper
7
1
System tamper
7
2
Keypad tamper
7
2
7
3
7
3
7
4
7
4
7
5
7
5
7
6
7
6
7
7
7
7
7
8
7
8
8
8
1 - 16
Keypad 1 - 16 tamper
Zone expansion module tamper
1-6
Zone expansion module 1 -6 tamper
Zone tamper DEOL
1 - 16
Sensor tamper DEOL
Zone type tamper
1 – 16
Zone type 1 – 16 tamper
Keypad Lock out
1
Keypad Lock out
RF receiver tamper
1
RF receiver tamper
RF repeater tamper
1–8
RF repeater tamper
External failure
1 - 16
External fault zone 1 - 16
Table 9.1: Types of fault or tamper conditions
* In case one or more faults occur in this category
Fault Description
1 - Accessory Module Failure
–
Network/IP Module 1-2 Failure
Condition:
No communication with the DX4020 / ITS-DX4020G if DX4020 / ITS-DX4020G is available.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
Troubleshooting | en
AMAX panel
155
Restore:
4
Restore the communication with DX4020 / ITS - DX4020G to a normal condition and reset
the fault. For more information, refer to DX4020-G, page 23.
Supervise:
1.
Report the DX4020 / ITS - DX4020G fault to configured destination on address 124 when
the fault is detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off, when there is no other system fault.
–
Output Expansion Module 1-2 Failure
Condition:
No communication with DX3010 if DX3010 is available.
Restore:
4
Restore the communication with DX3010 to a normal condition and reset the fault. For
more information, refer to DX3010, page 18.
Supervise:
1.
Report the DX3010 fault to configured destination on address 140 when the fault is
detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off, when there is no other system fault.
–
Input Expansion Module 1-6 Failure
Condition:
No communication with DX2010 if DX2010 is available.
Restore:
4
Restore the communication with DX2010 to a normal condition and reset the fault. For
more information, refer to DX2010, page 17.
Supervise:
1.
Report the DX2010 fault to configured destination on address 140 when the fault is
detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off, when there is no other system fault.
–
Printer Failure
Module DX4010 Missing
Condition:
No communication with DX4010 if printer is available.
Restore:
4
Restore the communication with DX4010 to a normal condition and reset the fault.
Supervise:
1.
Report the DX4010 missing fault to configured destination when the fault is detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off, when there is no other system fault.
Printer Missing
Condition:
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
156
en | Troubleshooting
AMAX panel
No communication with the printer available, if the printer is enabled and the DX4010 is in a
normal condition.
Restore:
4
Restore the communication with the printer to a normal condition and reset the fault.
Supervise:
1.
Report the printer missing fault to configured destination when the fault is detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off, when there is no other system fault.
Printer Fault
Condition:
The printer condition is abnormal (e.g. printer no paper/printer buffer is overflow/...) if printer
is enabled and the DX4010 is in a normal condition.
Restore:
4
Restore the printer to a normal condition and reset the fault.
Supervise:
1.
Report the printer error to configured destination when the fault is detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off, when there is no other system fault.
–
RF Receiver Failure
RF Receiver 1 Fault
Condition:
The receiver condition is abnormal (e.g. RF micro is removed/hold RF micro in reset/...) if a
wireless module is enabled.
Restore:
4
Restore the communication with the receiver to a normal condition and reset the fault.
For more information, refer to RF devices, page 92.
Supervise:
1.
Report the receiver fault to configured destination when the fault is detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off, when there is no other system fault.
RF Receiver 1 Missing
Condition:
1.
No communication with receiver available if a wireless module is enabled.
2.
A RF zone, repeater or keyfob is configured, but the wireless module is disabled.
Restore:
4
Restore the communication with the receiver to a normal condition, enable the wireless
module and reset the fault. For more information, refer to RF devices, page 92.
Supervise:
1.
Report the receiver missing fault to configured destination when the fault is detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off when there is no other system fault.
RF Receiver 1 Jammed
Condition:
A signal is disturbing the receiver if a wireless module is enabled.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
Troubleshooting | en
AMAX panel
157
Restore:
4
Remove the disturbing signal around the receiver, enable the wireless module and reset
the fault. For more information, refer to RF devices, page 92.
Supervise:
1.
Report the receiver jam fault to configured destination when the fault is detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off when there is no other system fault.
–
RF Sensor Failure
RF Sensor Missing
Condition:
A wireless zone sends no status report to the receiver in the RF supervision interval if a
wireless module is enabled.
Restore:
4
Make sure that all wireless zones are sending status reports to the receiver in the RF
supervision interval and reset the fault. For more information, refer to RF devices, page 92.
Supervise:
1.
Report the wireless zone missing fault to configured destination when the fault is
detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off when there is no other system fault.
RF Sensor Fault
Condition:
A wireless zone is in an abnormal condition (e.g. Remove the pyro from the smoke
detector/...) and a wireless module is enabled.
Restore:
4
Restore all wireless zones to a normal condition and reset the fault. For more
information, refer to RF devices, page 92.
Supervise:
1.
Report the wireless zone fault to configured destination when the fault is detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off when there is no other system fault.
–
RF Repeater Failure
1-8 RF Repeater 1-8 Missing
Condition:
No status report is send to the receiver in the RF supervision interval if a wireless module is
enabled.
Restore:
4
Make sure that status reports are sent to the receiver in the RF supervision interval and
reset the fault. For more information, refer to RF devices, page 92.
Supervise:
1.
Report the repeater missing fault to configured destination when the fault is detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off when there is no other system fault.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
158
en | Troubleshooting
–
AMAX panel
RF Config Failure
Configuration Conflict Sensors
Condition:
A wireless zone configuration is in error condition.
Restore:
4
Restore all wireless zones to a normal condition and reset the fault. For more
information, refer to RF devices, page 92.
Supervise:
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
4
Reset the fault.
P
The FAULT indicator is turned off when there is no other system fault.
Configuration Conflict Repeaters
Condition:
A repeater configuration is in error condition.
Restore:
4
Restore all repeaters to a normal condition and reset the fault. For more information,
refer to RF devices, page 92.
Supervise:
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
4
Reset the fault.
P
The FAULT indicator is turned off when there is no other system fault.
Configuration Conflict Keyfobs
Condition:
A keyfob configuration is in error condition.
Restore:
4
Restore all keyfobs to a normal condition and reset the fault. For more information, refer
to RF devices, page 92.
Supervise:
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
4
Reset the fault.
P
The FAULT indicator is turned off when there is no other system fault.
2 - Power Failure
–
Panel AC Failure
Condition:
1.
AC supply deficiency caused by a transformer.
2.
Power supply fuse is broken (230V).
3.
Power supply is disconnected (230V).
Restore:
1.
Reconnect the AC supply and reset the fault. For more information refer to Installation,
2.
Monitor the voltage by MPU.
page 26.
Supervise:
1.
If the AC supply is not restored one hour after the fault occurred, report the fault to
configured destination on address 124.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
Troubleshooting | en
AMAX panel
159
When the AC supply is reconnected, the MAINS indicator lights up (except in
programming mode or in code functions mode).
2.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off when there is no other system fault.
–
Battery Low Battery
Condition:
1.
The battery voltage is lower than 11V+-1%.
2.
No battery is connected.
Restore:
1.
Connect a battery. For more information, refer to Battery installation, page 27.
2.
Raise battery voltage to 12V+-1%, perform a dynamic battery test (time set in
programming address 204) and reset the fault.
Supervise:
1.
Set the system to perform a dynamic battery test on a regular basis (time set in
programming address 204) and every time the system is armed or reset.
2.
Report the low battery to the configured destination programmed on address 124.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
3.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off when there is no other system fault.
–
Panel Aux Power 1-2 Failure
Condition:
The Aux power supply voltage is lower than 9V.
Restore:
4
Raise the voltage to 12V and reset the fault.
Supervise:
1.
Monitor the voltage by MPU.
2.
Report the AUX power fault to the configured destination programmed on address 124.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
3.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off when there is no other system fault.
–
Bosch Option Bus Power 1-2 Failure
Condition:
Bosch option bus power supply voltage is lower than 9V+-5%.
Restore:
4
Raise the voltage to 12V and reset the fault. For more information refer to Bosch option
bus, page 14.
Supervise:
1.
Monitor the voltage by MPU.
2.
Report the Bosch Option Bus Power Supply fault to the configured destination
programmed on address 124.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
3.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off when there is no other system fault.
–
RF Repeater 1-8 AC Power Failure
Condition:
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
160
en | Troubleshooting
AMAX panel
1.
AC power failure to the repeater.
2.
The repeater is not wired correctly, if a wireless module is enabled.
Restore:
4
Restore the repeater AC power and reset the fault.
Supervise:
1.
Report the repeater AC power fault to configured destination when the fault is detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off when there is no other system fault.
–
RF Repeater 1-8 Battery Failure
Condition:
The repeater is in a low battery condition if a wireless module is enabled.
Restore:
4
Restore the repeater battery and reset the fault. For more information refer to RF devices,
page 92.
Supervise:
1.
Report the repeater battery fault to configured destination when the fault is detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off when there is no other system fault.
–
RF Sensor Power Failure
Condition:
The sensor is in a low battery condition if a wireless module is enabled.
Restore:
4
Restore the sensor battery and reset the fault. For more information refer to RF devices,
page 92.
Supervise:
1.
Report the sensor power fault to configured destination when the fault is detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off when there is no other system fault.
–
RF Keyfob Battery Failure
Condition:
The keyfob is in a low battery condition if a wireless module is enabled.
Restore:
4
Restore the keyfob battery and reset the fault. For more information refer to RF devices,
page 92.
Supervise:
1.
Report the keyfob battery fault to configured destination when the fault is detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off when there is no other system fault.
3 -Output Failure
–
2016.05 | 08 | F.01U.309.277
Onboard Output 1-2 Fault
Installation Manual
Bosch Sicherheitssysteme GmbH
Troubleshooting | en
AMAX panel
161
Condition:
An onboard output is in a short circuit or open circuit condition.
Restore:
4
Restore the onboard output to a normal condition and reset the fault. For more
information refer to Outputs, page 85.
Supervise:
1.
Report the onboard output 1-2 fault to configured destination when the fault is detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off when there is no other system fault.
4 -Keypad Failure
–
Keypad 1-16 failure
Condition:
No communication between the panel and a keypad.
Restore:
4
Restore the communication between the panel and the keypad and reset the fault. For
more information refer to Keypad area, page 75.
Supervise:
1.
Report the keypad fault to the configured destination programmed on address 124.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off when there is no other system fault.
5- System Failure
–
Date and Time not set
Condition:
Date and time is not set after the system is powered on.
Restore:
4
Program date and time and reset the fault. For more information refer to System setting,
page 79.
Supervise:
1.
Report the date and time fault to the configured destination programmed on location
124.
2.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description)
3.
No report to the AMAX panel system, when date and time setting is recorded in
nonvolatile memory and AMAX Panel is reset. The FAULT indicator is turned off when
there is no other system fault.
6 - Communication Failure
–
Communication Fault 1 - 4
Condition:
The panel can not send the report to the destination 1 after four attempts.
Restore:
Make sure that reports can be sent and reset the fault. For more information refer to System
setting, page 79.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
162
en | Troubleshooting
AMAX panel
Supervise:
1.
Report the fault to configured destination on address 124 when the fault is detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off when there is no other system fault.
7- Tamper
–
System Tamper
Condition:
Onboard panel tamper input is open.
Restore:
4
Close the panel tamper input and reset the fault.
Supervise:
1.
Report the tamper condition to configured destination on address 124 when the tamper
condition is detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the tamper condition is reset, send the restored report to the configured
destinations.
P
The FAULT indicator is turned off when there is no other system fault.
–
Keypad 1-16 Tamper
Condition:
Keypad 1 is open and the tamper contact is triggered.
Restore:
4
Close the keypad and reset the tamper condition.
Supervise:
1.
Report the tamper condition to configured destination on address 124 when the tamper
condition is detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the tamper condition is reset, send the restored report to the configured
destinations.
P
The FAULT indicator is turned off when there is no other system fault.
–
Zone Expansion Module 1-6 Tamper
Condition:
A disassembly of DX2010 module 1, 2, 3, 4, 5, or 6 is detected and the occurrence of zone
extension module 1, 2, 3, 4, 5 or 6 is considered as a tamper condition.
Restore:
4
Restore the DX2010 module 1, 2, 3, 4, 5, or 6 to a normal condition and reset the fault.
For more information, refer to DX2010, page 17.
Supervise:
1.
Report the tamper condition to configured destination on address 0124 when the tamper
condition is detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the tamper condition is reset, send the restored report to the configured
destinations.
P
2016.05 | 08 | F.01U.309.277
The FAULT indicator is turned off when there is no other system fault.
Installation Manual
Bosch Sicherheitssysteme GmbH
Troubleshooting | en
AMAX panel
–
163
Zone Tamper 1-16 DEOL
Condition:
Tamper contact is triggered (if the corresponding zone is programmed as DEOL).
Restore:
4
Restore the tamper contact and reset the tamper condition.
Supervise:
1.
Report the sensor tamper to configured destination on address 124 when the sensor
tamper is detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the tamper condition is reset, send the restored report to the configured
destinations.
P
The FAULT indicator is turned off when there is no other system fault.
–
Zone type 1-16 Tamper
Condition:
Tamper contact (directly connected to the zone) is triggered (zone type = tamper).
Restore:
4
Restore the tamper contact and reset the tamper condition.
Supervise:
1.
Report the tamper condition to configured destination on address 124 when the tamper
condition is detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the tamper condition is reset, send the restored report to the configured
destinations.
P
The FAULT indicator is turned off when there is no other system fault.
–
Keypad Lock out
Condition:
If the number of incorrect code entries reaches the specified limit (programmed in address
0499), the keypad locks.
Restore:
4
Wait until the keypad lockout time (3min) expires and reset the fault.
Supervise:
1.
Report the keypad lock out to configured destination on address 124 when the keypad
lock out is detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the keypad lock out condition is reset, send the restored report to the configured
destinations.
P
The FAULT indicator is turned off when there is no other system fault.
–
RF Receiver Tamper
Condition:
A receiver is in tamper condition (e.g. when someone removes the device from its base or
pulls it out of the wall) if a wireless module is enabled.
Restore:
4
Restore the receiver and reset the tamper condition. For more information refer to RF
devices, page 92.
Supervise:
1.
Report receiver tamper fault to configured destination when the fault is detected.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
164
en | Troubleshooting
AMAX panel
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off when there is no other system fault.
–
RF Repeater Tamper
Condition:
A repeater is in tamper condition (e.g. when someone removes the device from its base or
pulls it out of the wall) if a wireless module is enabled.
Restore:
4
Restore the repeater and reset the tamper condition. For more information refer to RF
devices, page 92.
Supervise:
1.
Report repeater tamper fault to configured destination when the fault is detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off when there is no other system fault.
8 - External Failure
–
External Fault Zone 1-16
Condition:
A fault contact (direct connected to the zone) is triggered (zone type = external fault).
Restore:
4
Restore the fault contact and reset the fault.
Supervise:
1.
Report the fault condition to configured destination on address 124 when the fault
condition is detected.
Slow flash FAULT indicator (refer to Keypad indicators, page 9 for a detailed description).
2.
When the fault is reset, send the restored report to the configured destinations.
P
The FAULT indicator is turned off when there is no other system fault.
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Maintenance | en
165
Maintenance
10
Caution!
!
10.1
Maintenance
Damage or malfunction of the system is possible if it is not maintained on a regular basis.
–
It is recommended to test the system once a week.
–
Make sure to get the system maintained four times a year.
–
Only qualified installers /service personnel are allowed to maintain this system.
Firmware upgrade with the ICP-EZRU2 upgrade key
Use the ICP-EZRU2 firmware upgrade key (green) to upgrade the firmware of the AMAX panel.
1.
Power off the AMAX panel and remove the battery.
2.
Unplug the USB cable, if plugged.
3.
Connect the firmware upgrade key to the plug on top of the printed circuit board (PCB)
of the AMAX panel. Make sure that the direction of the programming key is consistent
with the direction marked on the PCB.
4.
Power up the AMAX panel.
The LED of the firmware upgrade key flickers while the upgrade is sent to the AMAX
panel. This takes about one minute. When upgrade is terminated, the LED blinks slowly.
5.
Remove upgrade key.
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
166
11
en | Technical data
AMAX panel
Technical data
Electrical
AMAX 2100
AMAX 3000
AMAX 3000
AMAX 4000
BE
Power supply type
EN = A
Panel PCB maximum quiescent
100
current in mA
Transformer
Transformer input in VAC
230
Transformer output in VAC
18
Transformer AC power in VA
20
50
Transformer fuse in mA
500
1000
AC input
Minimum operating voltage in
195
VDC
Maximum operating voltage in
253
VDC
Line voltage frequency in Hz
50
DC output
DC output maximum current for 1100
2000
all components in mA
DC output maximum current for –
Battery 7Ah standby 12h (recharge Batt 80% in 72h) =
all components: dependency on
550mA
battery
–
Battery 7Ah standby 36h + 15min alarm current
500mA (recharge Batt 80% in 72h) = 150mA
–
Battery 18 Ah standby
12h (recharge Batt 80%
in 72h) = 1500mA
–
Battery 18Ah standby
36h (recharge Batt 80%
in 24h) = 480mA
–
Battery 18Ah standby
36h + 15min alarm
current 1000mA
(recharge Batt 80% in
24h) = 400mA
Aux 1 / 2 output
Aux 1 / 2 output voltage
+12V / GND
Aux 1 / 2 nominal output voltage 13.8 (+3% / -5%)
under AC line input in VDC
2016.05 | 08 | F.01U.309.277
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Technical data | en
AMAX 2100
AMAX 3000
AMAX 3000
167
AMAX 4000
BE
Aux 1 / 2 output max. Vpp in mV 675
Aux 1 / 2 output voltage range
12.82 – 13.9
13.11 – 14.2
500
900
under AC line input in VDC
Aux 1 / 2 output current in mA
Outputs
PO -1 / PO -2 maximum
500
supervised output current in mA
PO -3 maximum current in mA
100
PO +3 / PO +4 maximum current
750
in mA (+12V)
Watchdog PO -5 maximum
100
current in mA
Option bus
Option bus nominal output
13.8 (+3% / -5%)
voltage under AC line input in
VDC
Option bus output voltage range 13.11 – 14.2
under AC line input in VDC
Option bus 1 maximum current
500
900
in mA
Option bus 2 maximum current
900
in mA
Battery
Battery type
12 V / 7 Ah
12 V / 7Ah / 12 V / 18 Ah
Bosch D 126
Bosch IPS-BAT12V-18AH
Low battery condition in VDC
below 11.0
Minimum battery condition in
10.8
VDC
Electrical: Keypads
IUI-AMAX4-TEXT
IUI-AMAX3-LED16 IUI-AMAX3-LED8
(LCD text keypad) (16 zone LED
keypad)
Minimum operating voltage in
(8 zone LED
keypad)
10.8
VDC
Maximum operating voltage in
13.8
VDC
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
168
en | Technical data
AMAX panel
IUI-AMAX4-TEXT
IUI-AMAX3-LED16 IUI-AMAX3-LED8
(LCD text keypad) (16 zone LED
keypad)
Standard current consumption
(8 zone LED
keypad)
31
in mA
Maximum current consumption
100
60
in mA
EN type
B
Mechanical
AMAX 2100
AMAX 3000
AMAX 3000
AMAX 4000
BE
Dimension in cm (H x W x D)
26.0 x 28.0 x 8.35
37.5 x 32.2 x 8.8
Weight in g
1950
4700
Panel features
Number of zones
8
32
64
Number of users
64
128
250
Number of events
256 history events, stamped with time, and date
256 EN history events, stamped with time, and date
256 dialer history events, stamped with time, and date
Pin code variations
1000000
Number of devices
Number of keypads
4
Number of DX 2010 modules
Number of DX 3010 modules
1
Number of DX 4010 modules
1
8
16
3
6
2
Number of GPRS modules: B450 Up to 2 different GPRS modules, each GPRS module can
with B442 or B443, DX4020-G
only be connected once
Number of IP modules: B426,
2 (1 if 1 of the GPRS modules above is connected, 0 if 2 of
B450
the GPRS modules above are connected)
Number of RF receivers
-
1
Number of RF repeaters
-
DSRF = 0, RADION = 8
Number of RF sensors
-
32
Number of RF keyfobs
-
DSRF = 24, RADION = 128
64
Zones
Zone 1
2016.05 | 08 | F.01U.309.277
Single or dual end-of-line
2 wire fire zone, single, or
(EOL 2,2KΩ)
dual end-of-line (EOL 2,2KΩ)
NC, NO
NC, NO
Installation Manual
Bosch Sicherheitssysteme GmbH
AMAX panel
Technical data | en
AMAX 2100
AMAX 3000
AMAX 3000
169
AMAX 4000
BE
Zone 2 – 16 COM
7 single or dual end-of-line (EOL 2,2KΩ)
15 single or
NC, NO
dual end-ofline (EOL
2,2KΩ)
NC, NO
Tamper
Enclosure tamper input (does not reduce point capacity)
Option bus
Dimensions in mm
4 wire, Ø 0.6 – 1.2
Maximum cable length in m
200 (panel to last keypad)
Maximum bus length in m
700 (maximum 14 devices, maximum 8 keypads)
Environmental
AMAX 2100
AMAX 3000
AMAX 3000
AMAX 4000
BE
Minimum operating temperature -10
in °C
Maximum operating
55
temperature in °C
Minimum relative humidity in %
10
Maximum relative humidity in %
95
Protection class
IP 30, IK 06
Certification
Europe
CE
EN 50130-4 (6/2011)
EN 55022 (5/2008)
EN 60950-1:2006 + A11:2009
EN
EN 50131-3 grade 2
Environmental class II
France
AFNOR
NF a2P 1223400001
NF a2P 1223400002
Environmental class I
Belgium
INCERT (only for AMAX 3000 BE)
B-509-0063
Germany
VDS
Home
Bosch Sicherheitssysteme GmbH
Installation Manual
2016.05 | 08 | F.01U.309.277
Bosch Sicherheitssysteme GmbH
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany
www.boschsecurity.com
© Bosch Sicherheitssysteme GmbH, 2016
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement