V452-K - Panasonic Canada
VCR (mode)
TV (mode)
(Enables VCR functions)
POWER
(Enables TV functions)
POWER
DISPLAY
(Turns VCR off/on)
VCR
TV
1
2
3
(For TV or VCR mode)
4
5
6
7
8
SPEED
(Changes tape speed)
(Ejects tape)
9
ADD/DLT
EJECT
0
CM/ZERO
SEARCH
PLAY
COMMERCIAL SKIP/
ZERO SEARCH
(Starts COMMERCIAL SKIP/ Zero Search)
ACTION
(Displays menu)
REW
REC
FAST
FORWARD/
SEARCH
ADD/DELETE
PROG
STOP
SEARCH/ ENTER
(Set search system /Tunes TV channel)
TAPE
RESET
POSITION COUNTER PAUSE/SLOW
POWER
REWIND/
SEARCH
PLAY (Plays a tape)/
FAST FORWARD/SEARCH
REWIND/SEARCH
RECORD
(Rewinds tape/ reverse visual
search)
STOP (Stops tape)
CHANNEL UP/ DOWN
TRACKING/ V-LOCK
Remote
Sensor
RECORD
STOP/EJECT
Remote keys
(Records a program, etc.)
TAPE POSITION
(Locates tape position)
NUMBER Keys
(Fast forwards tape/ forward visual
search)
FF
SELECT
ACTION
DISPLAY
(Adds or deletes a channel)
SPEED
100
EJECT
PLAY
(Selects channel directly)
INPUT
INPUT
(For LINE or channel)
Cassette Compartment
(Displays VCR status)
VCR/TV
VCR/TV
VCR/TV selector
SAP/Hi-Fi
VOL
COUNTER RESET
CH
PLAY, STOP, REW, and FF
function as
operation keys when menus
are displayed.
TRACKING
(Resets counter to zero)
Rear View of the VCR
PROGRAM
SAP/Hi-Fi
(Displays Timer Program screen)
(Selects audio mode for play
or record)
PAUSE/SLOW
(Displays still, frame by frame,
or slow motion picture)
VOLUME +/-
AC Power Plug
While plugged into an AC outlet, the VCR consumes 3.0 W
of electrical power in off condition.
CHANNEL /
TRACKING/ V-LOCK
(Adjusts TV volume)
(Selects channel/ reduces
picture noise during Play and
Slow mode)
Audio Input Connector
(L/R)
EJECT button: Press to eject tape. EJECT is not available during recording.
VHF/UHF Antenna
Input Terminal
Video Input Connector
AUDIO
IN FROM ANT.
R
L
VIDEO
Multi Function Display
Power Indicator
Lights up when power is on.
IN 1
Timer Indicator
Lights up when the VCR is set for a Timer
Recording, or when One Touch Recording
(OTR) is used.
Flashes when a Timer Recording is set, but a
tape has not been inserted into the VCR.
OUT
VHF/UHF
OUT TO TV
VHF/UHF Antenna
Output Terminal
Audio Output
Connector (L/R)
Video Output
Connector
Reset Language, Channels, Clock,VCR’s Output Channel
VCR
CLOCK CHANNEL
REPEAT PLAY
:OFF
REMOTE WARNING :ON
AUTO SHUT- OFF
:OFF
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
Press ACTION*
to display MENU.
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3
PANASONIC PRODUCT – LIMITED WARRANTY
SELECT :
EXIT
: ACT I ON
Language
1) Press
to select
language item.
VCR
CLOCK CHANNEL
REPEAT PLAY
:OFF
REMOTE WARNING :ON
AUTO SHUT- OFF
:OFF
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
SELECT :
SET :
EXIT
: ACT I ON
repeatedly.
2) Press
VCR
CLOCK CHANNEL
REPEAT PLAY
:OFF
REMOTE WARNING :ON
AUTO SHUT- OFF
:OFF
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
SELECT :
SET :
EXIT
: ACT I ON
For English
VCR
RELOJ
CANAL
REPETICION
:INACT
AVISO/CONT.REMOTO :ACT
APAGADO AUTOMATICO :INACT
LANGUE/LANGUAGE:ESPAÑOL
CANAL DE SALIDA :3
ELEGIR
SAL I R
:
FIJAR :
: ACT I ON
For Spanish
MAGNETO. HORL.
CANAL
REPRISE LECTURE
: NON
MESSAGE D’ ERREUR
: OUI
COUPURE AUTO
: NON
LANGUAGE/IDIOMA : FRANÇAIS
CA SORTIE : 3
Channels
Clock
1) Press
to select
CHANNEL.
VCR
CLOCK CHANNEL
ANTENNA : CABLE
AUTO SET
WEAK SIGNAL DISPLAY : OFF
For French
3) Press ACTION to exit.
1) Press
CLOCK.
to select
VCR
CLOCK CHANNEL
AUTO CLOCK SET
MANUAL
TIME ZONE ADJUST : 0
Time Zone
Adjust
(Only when Auto Clock
is set.)
1) Press
to select
CLOCK.
VCR
CLOCK CHANNEL
AUTO CLOCK SET
MANUAL
TIME ZONE ADJUST : 0
SELECT :
: ACT I ON
EXIT
SELECT :
: ACT I ON
EXIT
2) Press
to select
2) Press
to select
“MANUAL,” and press
“ANTENNA,” then
SELECT :
. (For Auto Clock Set, EXIT : ACT I ON
press to set
select “AUTO CLOCK
your antenna system
to select
2) Press
SET.”)
(“TV” or “CABLE.”)
“TIME ZONE
VCR
CLOCK CHANNEL
VCR
CLOCK CHANNEL
ADJUST”
ANTENNA : CABLE
AUTO CLOCK SET
AUTO SET
WEAK SIGNAL DISPLAY : OFF
MANUAL
TIME ZONE ADJUST : 0
SET :
SELECT :
: ACT I ON
EXIT
SET :
SELECT :
EXIT
: ACT I ON
to select
3) Press
“AUTO SET,” then
press .
• If you use Cable
Box, set it to the
PBS channel in your
time zone.
VCR
CLOCK
(“TIME ZONE ADJUST”
appears only when
auto clock is set.)
VCR
CLOCK
CHANNEL
9 /29
29 / 2002 SUN 2 : --PM
CH AUTO SET PROCEEDING
CANCEL : STOP
• After Channel Auto
Set is finished, Auto
Clock Set will be
performed.
VCR
CLOCK CHANNEL
AUTO CLOCK SET
MANUAL
TIME ZONE ADJUST : 0
SET :
SELECT :
: ACT I ON
EXIT
and press to
subtract or add
hour(s) as necessary.
3) Press ACTION.
DST:ON
SELECT HOUR
SELECT :
SET :
: ACT I ON
EXIT
CHANNEL
SEL.
:
REGLER:
QUITTER : ACT I ON
3) Press
and
to select and set
the date, time, and
DST (Daylight
Saving Time).
• “TIME ZONE
ADJUST” returns to
“0” if clock is set
manually.
4) Press ACTION to
start the Clock and
exit this mode.
VCR’s Output Channel
1) Press
to select
“VCR’S OUTPUT CH.”
VCR
CLOCK CHANNEL
REPEAT PLAY
:OFF
REMOTE WARNING :ON
AUTO SHUT- OFF
:OFF
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
Richmond, British Columbia
Calgary, Alberta
Mississauga, Ontario
To add channel:
Select channel with NUMBER keys and
press ADD/DLT.
Panasonic Canada Inc.
12111 Riverside Way
Richmond, BC V6W 1K8
Tel: (604) 278-4211
Fax: (604) 278-5627
Panasonic Canada Inc.
6835-8th St. N. E.
Calgary, AB T2E 7H7
Tel: (403) 295-3955
Fax: (403) 274-5493
Panasonic Canada Inc.
5770 Ambler Dr.
Mississauga, ON L4W 2T3
Tel: (905) 624-8447
Note
Fax: (905) 238-2418
CHANNEL 08 ADDED
2) Press
CLOCK
Lachine, Québec
.
CHANNEL
To delete channel:
Select channel with CH / or NUMBER
keys and press ADD/DLT.
IF YOU PRESS ACTION
KEY, VCR ’ S OUTPUT CH
SWITCHES TO CH 4.
CHANNEL 08 DELE TED
VCR
CLOCK
CHANNEL
PLEASE TUNE YOUR TV TO
CH 4.
DST (Daylight Saving Time)
Panasonic Canada Inc.
5770 Ambler Drive,
Mississauga, Ontario L4W 2T3
(905) 624-5010
www.panasonic.ca
Montréal: 3075 Louis A. Amos, Lachine, Québec H8T 1C4 (514) 633-8684
Toronto: 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 238-2181
Calgary: 6835 8th Street N.E., Calgary, Alberta T2E 7H7 (403) 295-3922
Vancouver: 12111 Riverside Way, Richmond, BC V6W 1K8 (604) 278-4211
Printed in Indonesia
LSQT0546A
S0102-0
-8-
LSQT0546A(Basic Operations) - Front
After 3 seconds
Hi-Fi Indicator
Lights up when Hi-Fi audio is
monitored in Playback Mode.
VCR
CLOCK CHANNEL
REPEAT PLAY
:OFF
REMOTE WARNING :ON
AUTO SHUT- OFF
:OFF
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :4
Note to CABLE system installer
This reminder is provided to call the CABLE system installer’s attention to Article 820-40 of the
NEC in USA (and to the Canadian Electrical Code in Canada) that provides guidelines for
proper grounding and, in particular, specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of cable entry as practical.
K
SELECT :
SET :
: ACT I ON
EXIT
• To Make Corrections,
repeat steps 1) ~ 3).
VCR auto adjusts clock for DST.
Spring (First Sunday in April)
DST:ON ➛ Sets clock ahead one hour.
Autumn (Last Sunday in October)
DST:ON ➛ Turns clock back one hour.
• If your area does not observe Daylight
Saving Time, select DST:OFF.
• Keep these time changes in mind when
programming VCR for timer recordings.
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
-9-
- 10 -
WARRANTY SERVICE
For product operation and information assistance, please contact your
Dealer or our Customer Care Centre at:
Telephone #:
Fax #:
Web:
(905) 624-5505
(905) 238-2360
www.panasonic.ca
Add or Delete a Channel
SELECT :
SET :
: ACT I ON
EXIT
3) Press ACTION.
Clock/ Status/ Channel/ Speed Display
Displays the current time. Briefly displays VCR
status when a function button is pressed.
Briefly displays the channel number, or “L” when a
channel or line input is selected. Briefly displays the
recording speed when SPEED is pressed.
Panasonic Canada Inc. warrants this product to be free from defects in
material and workmanship and agrees to remedy any such defect for a
period as stated below from the date of original purchase.
VHS Video Cassette Recorder – One (1) year, parts and labour
LIMITATIONS AND EXCLUSIONS
This warranty does not apply to products purchased outside Canada or to
any product which has been improperly installed, subjected to usage for
which the product was not designed, misused or abused, damaged during
shipping, or which has been altered or repaired in any way that affects the
reliability or detracts from the performance, nor does it cover any product
which is used commercially. Dry cell batteries are also excluded from
coverage under this warranty.
This warranty is extended to the original end user purchaser only.
A purchase receipt or other proof of date of original purchase is required
before warranty service is performed.
THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, EXCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.
IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR ANY
SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES.
In certain instances, some jurisdictions do not allow the exclusion or
limitation of incidental or consequential damages, or the exclusion of implied
warranties, so the above limitations and exclusions may not be applicable.
Video Cassette Recorder
Operating Instructions
(Basic Operations)
For advanced operations, see the separate
“Advanced Operations” instruction book.
Model No. PV-452-K
For product repairs, please contact one of the following:
• Your Dealer who will inform you of an authorized Servicentre nearest you.
• Our Customer Care Centre at (905) 624-5505 or www.panasonic.ca
• A Panasonic Factory Servicentre listed below:
VCR
VCR Indicator
Lights up when the
VCR/TV selector is
set to VCR.
Limited Warranty
• Warranty • Reset Language, Channels, Clock, VCR’s Output Channel • DST
Front View of the VCR
Remote Control Buttons
• Location of Controls (Remote Control Buttons, Multi Function Display, Front & Rear View of the VCR )
Location of Controls
Location of Controls
- 11 -
Panasonic Canada Inc.
3075, rue Louis A. Amos
Lachine, QC H8T 1C4
Tel: (514) 633-8684
Fax: (514) 633-8020
CUSTOMER’S RECORD:
Customer Name:
Model Number:
Date of Purchase:
Dealer’s Name:
Address:
Table of Contents
Important Safeguards and Precautions .................... 2
Before Using ............................................................ 3
Connections and Initial Setup (Ready to Play) ......... 4
Playback / Record on a Tape ................................... 5
Timer Recording ................................................... 6, 7
Location of Controls ........................................... 9, 10
Reset Language, Channels,
Clock, VCR’s Output Channel .............................. 11
Limited Warranty .................................................... 12
Serial Number:
Phone Number:
IF YOU SHIP THE PRODUCT TO A SERVICENTRE
Carefully pack and send prepaid, adequately insured and preferably in the
Accessory Purchases:
original carton. Include details of the defect claimed, and proof of date of original
purchase.
As an ENERGY STAR Partner, Panasonic
has determined that this product or product
model meets the ENERGY STAR guidelines
for energy efficiency.
Please read these instructions carefully before attempting to connect,
operate or adjust this product. Please save this manual.
LSQT0546A
- 12 -
INSTALLATION
1 POWER SOURCE CAUTION
Operate only from a power source indicated on
the unit or in this manual. If necessary, have
your Electric Utility Service Company or Video
Products Dealer verify the power source in your
home.
2 POLARIZED OR GROUNDING PLUG
As a safety feature, this Video product comes
with either a polarized power cord plug (one
blade is wider than the other), or a three-wire
grounding type plug.
POLARIZED PLUG CAUTION:
This plug will only fit into an outlet one way. If you
cannot fully insert the plug, try reversing it. If it still
will not fit, have an electrician install the proper wall
outlet. Do not defeat the safety feature by tampering
with the plug.
GROUNDING PLUG CAUTION:
This plug will only fit into a three-hole grounding
outlet. If necessary, have an electrician install the
proper outlet. Do not defeat the safety feature by
tampering with the plug.
3 POWER CORD
Make sure power cords are routed so that they
are not likely to have anything rest on them, roll
over them, or be in the way of walking traffic.
If an extension cord is used, make sure it also
has either a polarized or grounded plug and that
the cords can be securely connected. Frayed
cords, damaged plugs, and damaged or cracked
wire insulation are hazardous and should be
replaced by a qualified service technician.
Overloaded outlets and extension cords are fire
hazards and should be avoided.
4 DO NOT BLOCK VENTILATION HOLES
Ventilation openings in the cabinet release heat
generated during operation. If they are blocked,
heat build-up inside the unit can cause failures
that may result in a fire hazard or heat damage
to cassettes. For protection, follow these rules:
a. Never cover ventilation slots or the unit while
in use, or operate the unit when placed on a
bed, sofa, rug, or other soft surface.
b. Avoid built-in installation, such as a book
case or rack, unless proper ventilation is
provided.
5 AVOID EXTREMELY HOT LOCATIONS OR
SUDDEN TEMPERATURE CHANGES
Do not place the unit over or near any kind of
heater or radiator, in direct sunlight, inside a
closed vehicle, etc.. Do not move the unit
suddenly between areas of extreme temperature
variation. If the unit is suddenly moved from a
cold place to a warm place, moisture may
condense in the unit and on the tape.
6 TO AVOID PERSONAL INJURY
• Do not place unsecured
equipment on a sloping
surface.
• Do not place this unit on any
support that is not firm, level,
and adequately strong. The
unit could fall causing serious
injury to a child or adult and
damage to the unit.
• An appliance and cart combination should be
moved with care. Quick stops, excessive force,
and uneven surfaces may cause the appliance
and cart combination to overturn.
• Carefully follow all operating instructions and
use the manufacturer's recommended
accessories when operating this unit or
connecting it to any other equipment.
Congratulations
OUTDOOR ANTENNA INSTALLATION
1 SAFE ANTENNA AND CABLE CONNECTION
If an outside antenna or cable system is connected to the
equipment, be sure the antenna or cable system is grounded
so as to provide some protection against built up static
charges and voltage surges.
Part 1 of the Canadian
Electrical Code, in USA
Section 810 of the National
Electrical Code, ANSI/NFPA
70, provides information with
respect to proper grounding
of the mast and supporting
structure, grounding of the
lead-in wire to an antenna discharge unit, size
of grounding conductors, location of antenna discharge unit,
connection to grounding electrodes and requirements for the
grounding electrode.
2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER
LINES OR CIRCUITS
An outside antenna system should be located well away
from power lines, electric light or power circuits and where it
will never come into contact with these power sources if it
should happen to fall. When installing an outside antenna,
extreme care should be taken to avoid touching power lines,
circuits or other power sources as this could be fatal.
Because of the hazards involved, antenna installation should
be left to a professional.
NEC - NATIONAL
Head Cleaning
on your new purchase! With proper use, this
dependable product will provide years of
enjoyment. Please fill in the information below.
(Serial number is on tag on back of VCR.)
• Date of Purchase
ELECTRICAL CODE
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
USING THE VIDEO UNIT
If the unit has been in storage or moved to a new location, refer
first to the INSTALLATION section of these safeguards.
1 KEEP THIS VIDEO UNIT AWAY FROM WATER OR
MOISTURE OF ANY KIND.
2 IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR
STRONG IMPACT, unplug the unit and have it inspected by
a qualified service technician before use.
3 DURING AN ELECTRICAL STORM
During a lightning storm, whether indoors or outdoors, or
before leaving the unit unused for extended periods of time,
disconnect all equipment from the power source as well as
the antenna and cable system.
4 WHEN THE UNIT IS PLUGGED IN
• Never expose the unit to rain or water. DO NOT
OPERATE if liquid has been spilled into the unit.
Immediately unplug the unit, and have it inspected by a
service technician. Fire and shock hazards can result from
electrical shorts caused by liquid contact inside.
• Never drop or push any object through openings in the
unit. Some internal parts carry hazardous voltages and
contact can cause electric shock or fire hazard.
• Avoid placing the unit directly above or below your TV set
as this may cause electrical interference. Keep all
magnets away from electronic equipment.
5 USING ACCESSORIES
Use only accessories recommended by the manufacturer to
avoid risk of fire, shock, or other hazards.
6 CLEANING THE UNIT
Unplug the unit. Then, use a clean, dry, chemically
untreated cloth to gently remove dust or debris. DO NOT
USE cleaning fluids, aerosols, or forced air that could overspray, or seep into the unit and cause electrical shock. Any
substance such as wax, adhesive tape, etc. may mar the
cabinet surface. Exposure to greasy, humid, or dusty areas
may adversely affect internal parts.
SERVICE
1 DO NOT SERVICE THIS PRODUCT YOURSELF
If, after carefully following the detailed operating instructions,
this Video product does not operate properly, do not attempt
to open or remove covers, or make any adjustments not
described in the manual. Unplug the unit and contact a
qualified service technician.
2 IF REPLACEMENT PARTS ARE REQUIRED
Make sure the service technician uses only parts specified
by the manufacturer, or those having the same safety
characteristics as the original parts. The use of unauthorized
substitutes may result in fire, electric shock, or other
hazards.
3 HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY
CHECK
After any service or repairs to the unit, request the service
technician to conduct a thorough safety check as described
in the manufacturer’s service literature to ensure that the
video unit is in safe operating condition.
• Dealer Purchased From
• Dealer Address
• Dealer Phone No.
• Model No.
PV-452-K
• Serial No.
Old or damaged tapes may clog heads.
Video Head Clog Sensor
Screen-right appears during
play if clogging is detected.
V I DEO HEADS MAY
NEED CLEAN I NG
To remove screen, press
PLEASE I NSERT HEAD
CLEAN I NG CASSETTE
PLAY.
OR REFER TO MANUAL
• Use “dry” type head
END
: PLAY
cleaning cassette only.
(Part No. NV-TCL30PT is recommended.)
• Follow cleaning tape instructions carefully.
Excessive use of tape can shorten head life.
Accessories
Remote Control
Batteries 2 “AA”
LSSQ0264
POWER
DISPLAY
VCR
TV
VCR/TV
1
2
3
4
5
6
7
8
100
0
INPUT
RF Coaxial
Cable
VJAS0196
SPEED
9
ADD/DLT
EJECT
CM/ZERO
SEARCH
Cleaning the VCR
Use soft, dry cloth or dusting attachment of a
vacuum to remove dust from all cabinet vent
holes. You may moisten cloth with non-abrasive,
antistatic cleaner/ polisher.
Caution:
Alcohol and various solvents could damage
finish.
PLAY
REW
FF
SELECT
ACTION
REC
Specifications
PROG
STOP
TAPE
RESET
POSITION COUNTER PAUSE/SLOW
SAP/Hi-Fi
VOL
Power Source:
120 V AC, 60 Hz
Power Consumption: Power On
CH
Approx. 23 W
TRACKING
Power Off
Video Signal:
Video Recording
System:
Audio Track:
Loading the Batteries
Battery replacement caution
• Do not mix old and new batteries.
• Do not mix alkaline with manganese batteries.
Approx. 3.0 W
EIA Standard NTSC colour
4 rotary heads helical
scanning system
1 track (Normal)
2 channel
Tuner:
Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69
CABLE Channels: Midband A ~ I (14 ~ 22)
Superband J ~ W (23 ~ 36)
Hyperband AA ~ EEE
(37 ~ 64)
Lowband A-5 ~ A-1 (95 ~ 99)
Special CABLE channel 5A
(01)
Ultraband 65 ~ 94, 100 ~ 125
Operating
Temperature:
5 °C ~ 40 °C (41 °F ~ 104 °F)
Operating Humidity: 10 % ~ 75 %
Weight:
2.5 kg (6.0 lbs).
Dimensions:
360 (W) x 93 (H) x 242 (D) mm
14-3/16” (W) x 3-11/16” (H) x
9-9/16” (D) inch
Note: Designs and specifications are subject
to change without notice.
Prevent Accidental Tape Erasure
To record again
Break off the tab to
prevent recording.
Features for a Quality Picture
Digital Auto Picture
Automatically controls the video output signal for
less noise depending on the tape condition.
Digital Auto Tracking
Cover the hole
with cellophane
tape.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
Record/Playback Time
Only use tapes with the
Tape Speed
Setting
SP
-2-
LSQT0546A(Basic Operations) - Back
Type of Video Cassette
T60
(Standard Play) 1 Hour
LP
(Long Play)
FCC Warning: Any unauthorized changes or modifications to this equipment would void the
user’s authority to operate.
mark in this unit.
T120
Manual Tracking Control
(to reduce picture noise)
Use during Playback and Slow Motion mode to
reduce picture noise.
Press CH (TRACKING) / on the remote
control or on the VCR until the picture clears up.
To return to Auto Tracking, press POWER off,
then on again a few seconds later.
T160
2 Hours
2 Hours 40 Minutes
R
R
R
SLP
5 Hours
2 Hours 4 Hours 20 Minutes
(Super Long Play) 3 Hours 6 Hours
8 Hours
R
V-Lock Control (to reduce picture jitter)
In Still mode, CH (TRACKING)
a V-Lock control.
-3-
Plugging the VCR Power Cord into an AC wall outlet starts auto channel and clock set.
/
operates as
Record on a Tape
Playback a Tape
1 Insert a tape.
• Loose or peeling labels
may cause tape jam.
Connecting
For ANT./Cable ➛ VCR ➛ TV
1 Connect cable from
Antenna/Cable to VCR’s IN
FROM ANT. jack.
2 Connect VCR’s OUT TO TV
jack to TV’s ANT. IN jack
with included RF Cable
accessory.
VCR
IN FROM ANT.
TV
1
2
IN FROM ANT. Cable TV
Converter Box
1
OUT TO TV
VHF/UHF
IN from
ANT./CABLE
2
After search has begun, each additional
press of FF or REW changes speed as
shown below.
[SLP] : Approx. 21X ↔ Approx. 9X
[LP] : Approx. 9X ↔ Approx. 7X
[SP] : Approx. 7X ↔ Approx. 3X
If at 21X, 9X, or 7X speed the picture is
interrupted, change speed to 9X, 7X, or 3X.
Notes
• Picture interruption may occur with some TVs.
• FF and REW search speed may vary
depending on current tape position.
Still (Freeze) Picture
➛ Press PAUSE/SLOW.
➛ Press PLAY to release.
Initial Setup (Ready to Play)
1 Turn TV on and tune to channel 3.
2 Plug VCR Power Cord into AC wall
Special Features During Play
Forward/Reverse Scene Search
➛ Press FF or REW.
➛ Press PLAY to release.
VHF/UHF
VCR
2 Press PLAY to play tape.
• If tape has no rec. tab (p. 3), auto play begins.
IN from
ANT./CABLE
OUT TO TV
For DSS/Cable Box ➛ VCR ➛ TV
1 Connect your cable box’s
TV
OUT jack to the VCR’s IN
FROM ANT. jack with an RF
cable.
2 Connect VCR’s OUT TO TV
jack to TV’s ANT. IN jack
with included RF Cable
accessory.
3 Settings are made automatically.
When setup is done, this screen
appears.
outlet. VCR comes on and auto
channel and clock set starts.
• If screen below does not appear, check
VCR - TV connection and, if TV is
tuned to channel 3, try switching it to
channel 4.
• To change VCR’s output channel,
please refer to “VCR’s Output Channel”
(p. 11).
VCR
CLOCK
CHANNEL
9 /29 / 2002 SUN 2 : 20PM
DST : ON
SETT I NG : CH 10
AUTO CLOCK SET
COMPLETED
If “AUTO CLOCK SET IS INCOMPLETE”
appears, manually set clock.
See below.
VCR
CLOCK
Frame by Frame Picture
➛ Press PAUSE/SLOW in Still mode.
➛ Press PLAY to release.
Slow Motion Picture
➛ Hold down PAUSE/SLOW in Still mode.
➛ Press PLAY to release.
Notes
• These features work best in SP or SLP mode.
• The sound will be muted.
• To reduce picture noise, see “Manual
Tracking Control” on p. 3.
• After VCR is in Still or Slow mode for 5 minutes,
it auto switches to Stop mode to protect the
tape and the video heads.
If Auto Clock Set was incomplete.
1 Press ACTION* on remote to display
CLOCK menu.
VCR
CANCEL : STOP
1/ /
CLOCK
CHANNEL
:
DST:ON
SELECT MONTH
VCR
CLOCK
AUTO CLOCK SET
2 Press
to select the month and
to set. In the same manner, select and
set the date, year, time, and DST
(Daylight Saving Time).
PROCEEDING
CANCEL : STOP
If you use a cable box, turn it on and set it
to the Public Broadcasting Station (PBS)
channel in your time zone. If you use a
DSS receiver, it must be turned off.
VCR
CLOCK
CHANNEL
9 /29 / 2002 SUN 2 : 20PM
• To edit, press PAUSE/SLOW to pause,
and again to resume recording.
5 Press STOP to stop recording.
One Touch Recording
(record in progress)
Press REC repeatedly to set length as follows:
30 min. ➛ 1 hr. ➛ 1:30 ➛ 2:00 ➛ 3:00
➛ 4:00 ➛ exit.
The VCR shuts off according to the length set.
Record one station, watch another
Press VCR/TV
(“VCR” goes out on Multi Function Display),
➛ select channels on TV (recording continues).
Select channels on VCR (in STOP or
PAUSE mode)
Press VCR/TV
(“VCR” lights up on Multi Function Display),
➛ select channels on VCR.
Notes
• Watching one channel and recording
another is not possible when using Cable
Box or DSS Receiver.
• After 5 minutes in Pause mode, VCR stops
to protect the tape and the video heads.
Review, Replace, or Clear Program
1 1) Press PROG*.
2) Press
2
(Recording is not in progress)
to display program screen.
Example
1) Set record DATE,
CH
Today
to select:
press
13 SAT --:-- --:-- -TODAY
1~31=
one
time,
SLP
SELECT START DATE
31 1
2
8 9
6
or DAILY= MON~ FRI,
SELECT :
SET:
END
: PROG
SELECT
/
Selection
Order
DAILY
or WEEKLY= same time
7
each week and press .
WEEKLY
WEEKLY
WEEKLY
(SAT)
(MON)
(SUN)
2) Set remaining items,
to select and
press
press to set START/ STOP times,
CH(channel) or LINE input (p. 9 of “Advanced Operations”
book), and tape speed (p. 3).
TIMER PROG.
DATE
START
LIST
STOP
Press PROG to end programming.
a 1) Press PROG.
to select LIST.
2) Press
b
TIMER PROG.
L I ST
DT START
STOP CH SPD
7
9 : 00A 12 : 00A 08
SP
8 10 : 00P 12 : 00P 02 SP
10
8 : 00P 9 : 00P 10 SP
9 : 00P 10 : 00P L
LP
SU
TIMER PROG.
L I ST
DT START
STOP CH SPD
13 2 : 00 P 3 : 20P 02 SLP
-- -- : -- -- : --- --- --- -- : -- -- : --- --- -- : -- -- : -CANCEL : ADD / DLT
SELECT :
SET :
EXIT
: PROG
To Enter More Programs
Press
to select and
press to set an unused program.
Then repeat step 2.
Or, press PROG to exit.
4 Press POWER off to set the timer Recording. (“TIMER” lights on Multi Function Display.)
(Recording is in progress)
Press POWER and then STOP within
10 seconds to cancel the Timer
Recording.
(The TIMER indicator goes out on Multi
Function Display.)
CANCEL : ADD / DLT
SELECT :
SET :
EXIT
: PROG
c To Replace program...
TIMER PROG.
DATE
START
LIST
STOP
CH
7 SUN 9:00A 12:00A 08
TODAY
SP
SELECT START DATE
3
Press
to select
desired program.
Cancel a Timer Recording
SET:
SELECT :
END
: PROG
1) Press to display.
2) Repeat Step 2
(page 6) to set
new programs.
or
To Clear program...
TIMER PROG.
L I ST
DT START
STOP CH SPD
-- -- : -- -- : --- -8 10 : 00P 12 : 00P 02 SP
10
8 : 00P 9 : 00P 10 SP
9 : 00P 10 : 00P L
LP
SU
Press ADD/DLT.
CANCEL : ADD / DLT
SELECT :
SET :
EXIT
: PROG
d Press PROG to end the programming.
Notes
• If you are using a Cable Box, VCR Timer Programming Channel (Step 2 above) must
be set to the Cable Box output channel and your Cable Box must be manually set to
the desired channel. The Cable Box must be left on.
• If a power interruption occurs while programming the timer, the timer program(s) may be
cancelled. If “TIMER PROGRAMS WERE LOST DUE TO POWER INTERRUPTION”
appears on-screen, please re-enter the timer programs.
Important notes when using DSS receiver
• When recording programs via DSS receiver, DSS receiver must be left on.
• When recording programs via an antenna or cable, DSS receiver must be turned off.
Auto Operation Functions
Insert a tape ➛ Power comes on ➛ Play starts if there is no record tab (see p. 3).
Auto Rewind
Play
Fast Forward
➛ Tape end ➛ Rewind
Play Auto Eject
(Repeat Play must be off)
Play ➛ Tape end ➛ Rewind ➛ Tape ejects if there is no record tab
DST:ON
SET COMPLETED
:
SET
START : ACT I ON
WARNING
Over tightening “Nut type” RF coaxial cables
may damage jacks. Finger tighten only.
to start recording.
Timer Recording
Auto Play
SELECT :
SET :
: ACT I ON
EXIT
CHANNEL
4 Press REC
Timer Recording
This video recorder, equipped with
HQ (High Quality) system, is
compatible with existing VHS
equipment. Only use tapes with the
mark. Only tapes tested and
inspected for use in 2, 4, 6, and 8
hour machines are recommended.
Manual Clock Set
CH AUTO SET PROCEEDING
to select record speed (p. 3).
Timer Recording
Press REW or FF in Stop mode to
Rewind or Fast Forward tape.
Press EJECT on remote,
or STOP/EJECT on VCR to eject tape.
Plugging the AC Power Plug into an AC outlet
CHANNEL
3 Press SPEED
3 Press STOP to stop tape.
PLEASE SET CLOCK BY
PRESSING ACTION KEY
CLOCK
• For “LINE” input, see p. 9 of “Advanced
Operations” book.
• If recording from a channel over 100, first
press 100 key then the other 2 digits.
CHANNEL
AUTO CLOCK SET IS
INCOMPLETE
VCR
1 Insert a tape with a record tab (p. 3).
2 Press CH or NUMBER keys
to select the channel.
R
This symbol warns the user that uninsulated
voltage within the unit may have sufficient
magnitude to cause electric shock. Therefore,
it is dangerous to make any kind of contact
with any inside part of this unit.
This symbol alerts the user that important
literature concerning the operation and
maintenance of this unit has been included.
Therefore, it should be read carefully in order
to avoid any problems.
Screw driver
R
Warning: To prevent fire or shock hazard, do not expose this equipment to rain or
moisture.
CAUTION: To prevent electric shock, match wide blade of plug to wide slot, fully insert.
Continuously analyzes the signal and adjusts for
optimum picture quality.
R
Record Tab
R
Safety Precautions
Please make all cable or antenna connections before plugging into the AC
outlet.
Playback / Record on a Tape
3 Press ACTION to start clock and exit.
-4-
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
-5-
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
-6-
-7-
• Timer Recording
FOR YOUR SAFETY, READ AND RETAIN
ALL SAFETY AND OPERATING
INSTRUCTIONS. HEED ALL WARNINGS IN
THE MANUAL AND ON THE UNIT
Connections / Initial Setup (Ready to Play)
• Connections • Initial Setup • Clock Set • Select Channel • Playback • Record • Auto Operation
Important Safeguards and Precautions
• Important Safeguards • Accessories • Head Cleaning • Loading Batteries • Prevent Tape Erasure • Specifications • Record/Playback Time
Before Using
To find out the present tape position.
Tape position is displayed for VHS-C type
Cassettes, tapes under 30 minutes long,
and some other tapes, but the position is
not correct.
(Rear connection shown.)
VCR
(HiFi)
VCR
(HiFi)
IN FROM ANT.
TV
OUT TO TV
R
R
L
1 Press ACTION to display menu.
VCR
CLOCK CHANNEL
REPEAT PLAY
:OFF
REMOTE WARNING :ON
AUTO SHUT- OFF
:OFF
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
1 Press TAPE POSITION
• “DETECTING TAPE
POSITION” only
appears the first time
a cassette is inserted
and it takes several
seconds for correct
indication to appear.
DETECTING TAPE POSITION
R
L
AUDIO IN
VIDEO OUT
When set to “ON,” picture is displayed
regardless of signal strength.
to detect tape position.
R
L
AUDIO OUT
Weak Signal Display ON/OFF Feature
VHF/UHF
VIDEO IN
BEG I N
• The present tape
position indication is
displayed.
END
2 Press TAPE POSITION
to return to normal screen.
1
Connect VIDEO OUT jack on Playing VCR to VIDEO IN jack on Recording VCR.
To monitor the dubbing, also connect a TV as shown.
2
Connect AUDIO L/R OUT jacks on Playing VCR to AUDIO L/R IN jacks on Recording
VCR.
Remote Warning ON/OFF Feature
In place of a Playing VCR, you can use other equipment, such as a Camcorder.
Simply connect the unit’s Audio/Video outputs to the Recording VCR.
If Multi-brand feature is used (page 2), and this
feature is set to on, a warning appears
whenever an invalid key is pressed in TV mode.
SELECT :
: ACT I ON
EXIT
2
VCR
CLOCK CHANNEL
ANTENNA : CABLE
AUTO SET
WEAK SIGNAL DISPLAY : OFF
SELECT :
SET :
: ACT I ON
EXIT
to select
Press
and display CHANNEL.
Press
to select
WEAK SIGNAL
DISPLAY, and press
to set ON or OFF.
• ON: Picture is displayed despite signal
condition and may be of poor quality.
OFF: Screen turns solid blue when signal
is weak or non-existent.
• Selecting ON has no effect on connected
equipment with blue back feature.
3 Press ACTION to return to normal screen.
Playing (Source) VCR
1
Recording (Editing) VCR
Insert pre-recorded tape.
Insert blank tape with record tab.
VCR
CLOCK CHANNEL
REPEAT PLAY
:OFF
REMOTE WARNING :ON
AUTO SHUT- OFF
:OFF
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
SELECT :
SET :
: ACT I ON
EXIT
2
Press INPUT* to set VCR Input mode to LINE
for Video Input. (See “Selecting the Input
Mode” below.)
and press to set ON
or OFF.
• If “OFF,” remote
warning will not appear
if invalid key is pressed.
When set to ON, all operations except for timer
record and tape eject are prohibited. Useful for
households with small children.
VCR LOCK ACT I VATED
3 Press ACTION to return to normal screen.
To turn on, hold down
REC on the VCR in Stop
mode with no tape
inserted for 7 sec.
(Please ignore the NO
CASSETTE warning.)
To turn off, repeat above.
VCR LOCK OFF
3
Press PLAY, then PAUSE/SLOW
immediately to enter PLAY/PAUSE mode.
Press REC, then PAUSE/SLOW
immediately to enter REC/PAUSE mode.
Before Requesting Service
Check the following points once again if you are having trouble with your VCR.
On-Screen Displays (OSD)
Function & Channel Displays
CH 0 8
(BO : refers to “Basic Operations” Instruction book.)
(AO : refers to “Advanced Operations” Instruction book.)
Blank Tape/
No Video Signal Indications
When a function button
is pressed, e.g. PLAY, or
you change channels,
a 5 second display
appears.
Power
When blank tape is detected during play,
or the current channel has no signal (with
Weak Signal Display feature (p. 10) set to
OFF), the TV screen will turn solid blue.
No power…
Recording & Playback
4
Press PLAY to start dubbing.
Playing VCR starts playback.
5
Press STOP to stop dubbing.
Press PAUSE/SLOW to start dubbing.
Recording VCR starts recording.
Press STOP to stop dubbing.
The power shuts off at a preset time.
• VCR Lock cancels in 24 hours if clock is set.
1 Press ACTION to display menu.
Press
to select
2
AUTO SHUT-OFF.
VCR
CLOCK CHANNEL
REPEAT PLAY
:OFF
REMOTE WARNING :ON
AUTO SHUT- OFF
:OFF
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
VCR Status & Clock Displays
To display or remove
overlay at right,
➛ press DISPLAY*.
Function Status
Current Time
CH 02
REC
1 2 : 0 0AM
-0 : 1 2 : 3 4
0 : 25
SP
STEREO
SAP
MONO
Rec Time Remaining
(OTR mode only.
See p. 5 of Basic
Operations book.)
Channel
Counter
Tape Speed
Broadcast Audio
Being Received
Warning and Instruction Displays
PLEASE SET CLOCK BY
PRESSING ACTION KEY
TURN VCR OFF
FOR TIMER RECORDING
(See p. 3 of Basic
Operations book.)
These displays will alert you to a missed
operation or provide further instructions.
Caution
Page
If you attempt to set or review a Timer
Recording and the Clock is not set...
See page 6 of
Basic Operations
book
After a Timer Program has been set...
See page 6 of
Basic Operations
book
During special effects playback,
picture may contain some vertical
jitter when using a TV with an
Automatic Vertical Hold Control...
• Set TV’s Vertical Hold Control to MANUAL, then
adjust.
VCR cannot be controlled...
•
•
•
•
•
Remote Control
VCR cannot be remote controlled...
CHECK CASSETTE
RECORD TAB
If you press REC on the remote
control or VCR, and a cassette is
inserted with no record tab...
See page 3 of
Basic Operations
book
NO CASSETTE
If you press PLAY, FF, REW, or REC
on the remote control or VCR without
a cassette inserted...
See page 5 of
Basic Operations
book
SELECT :
SET :
: ACT I ON
EXIT
TO CANCEL TIMER REC
PRESS POWER THEN
STOP KEY
Press repeatedly to
change shut-off time as
shown below.
REC
To Monitor Dubbing on Your TV
Selecting the Input Mode
1
Method 1:
Press INPUT repeatedly.
Channel Number ↔ LINE
2
Turn your TV on and tune to the
Recording VCR channel (CH3 or CH4).
Set the VCR/ TV Selector on the
Recording VCR to “VCR.”
Note
Panasonic Canada Inc.
5770 Ambler Drive,
Mississauga, Ontario L4W 2T3
(905) 624-5010
www.panasonic.ca
-8-
LSQT0547A(Advanced Operations) - Front
Printed in Indonesia
LSQT0547A
S0102-0
K
2 Hours
Method 2:
/ .
Press CH
Display will change as below.
• Dubbing tapes protected with
Copy Guard will result in poor
quality recordings.
1
LINE
2
3
(CABLE) (TV)
125 or 69
• “L” lights on Multi-Function Display
(about 4 sec.) when LINE is selected.
Montréal: 3075 Louis A. Amos, Lachine, Québec H8T 1C4 (514) 633-8684
Toronto: 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 238-2181
Calgary: 6835 8th Street N.E., Calgary, Alberta T2E 7H7 (403) 295-3922
Vancouver: 12111 Riverside Way, Richmond, BC V6W 1K8 (604) 278-4211
OFF
4 Hours
6 Hours
VIDEO HEADS MAY
NEED CLEANING
PLEASE INSERT HEAD
CLEANING CASSETTE
OR REFER TO MANUAL
END
If you press POWER or STOP during
a Timer Recording...
(visible in VCR mode only)
See page 6 of
Basic Operations
book
If head cleaning becomes necessary
while playing back a tape...
See page 3 of
Basic Operations
book
If you press a function button other
than STOP/EJECT or POWER while
the VCR is in VCR Lock mode...
See page 10
:PLAY
VCR LOCK ACTIVATED
• The shut-off countdown will not
function during Play or Record.
REMOTE CONTROL IS SET
TO TV MODE
If you press an invalid key on the
remote while in TV mode...
ACTION and PROG buttons do not
respond...
Miscellaneous
Video Cassette Recorder
Operating Instructions
(Advanced Operations)
For Basic operations, see the separate
“Basic Operations” instruction book.
Model No. PV-452-K
Make sure VCR power is on.
Check Remote batteries.
Make sure VCR LOCK is set to off. (AO p. 10)
Make sure Remote is in VCR mode. (AO p. 2)
Make sure Timer Recording is not in progress.
Correction
• Make sure VCR power is on.
• Make sure Remote is in VCR mode.
• Aim Remote Control directly at remote sensor on
VCR. (BO p. 10)
• Avoid any object blocking signal path.
• Check Remote batteries. (BO p. 3)
• Make sure VCR LOCK is set to off. (AO p. 10)
• Exposing VCR remote sensor to direct fluorescent or
outdoor light may cause signal interference.
• Check connections between VCR, external antenna,
and TV.
• Press VCR button for VCR mode. (AO p. 2)
• Check Remote batteries. (BO p. 3)
Correction
Programs cannot be viewed on TV... • Make sure TV power is on.
• Make sure TV is set to output of VCR.
• Check connections between VCR, external antenna,
and TV.
• Set VCR/TV selector to “TV.” (BO p. 5)
• Make sure proper signal source is selected.
Video cassette cannot be inserted... • Insert the cassette with window side up; record tab
facing you.
• Check if a tape is already in the unit.
Video cassette cannot be removed... • Completely insert Power Plug into an AC outlet.
Video cassette ejects when a
• Make sure cassette record tab is intact. (BO p. 3)
recording is started or the power is
turned off for timer recording...
In Stop mode, the motor
(CYLINDER) continues to rotate...
3 Press ACTION to return to normal screen.
Note
Correction
• Check connections between VCR, external antenna,
and TV.
• Check connections selection. (BO p. 4, AO p. 3)
• Make sure your antenna system (CABLE or TV) is
correctly set. (Channels [BO p. 11])
• Make sure cassette record tab is intact. (BO p. 3)
• Confirm that clock is set to current time and date.
Timer recording cannot be
• Make sure Cable/DSS box (if used) is left on and
performed…
tuned to channel to be recorded.
• Set recording start/stop times correctly. (BO p. 6)
• Make sure VCR POWER button is pressed off. (BO p. 6)
• Timer recording may not be performed or continued if
a power interruption occurs before or during a Timer
Recording, even after power is restored.
There is no playback picture, or the • Select channel 3 or 4 on TV to match VCR output
channel (3 or 4) (BO p. 4) or select LINE.
playback picture is noisy or contains
• Set VCR/TV selector to “VCR.”
streaks...
• Adjust TRACKING control in either direction. (BO p. 3)
• Try Head Cleaning. (BO p. 3)
Auto Shut-Off Feature
The operation of steps 4 and 5 must be done on the playing
and recording VCRs at the same time.
Correction
• Completely insert Power Plug into an AC outlet.
• Set POWER button to on.
• Make sure power source is active.
TV program cannot be recorded...
OSD
VCR Lock Feature
1 Press ACTION to display menu.
Press
to select
2
REMOTE WARNING
On-Screen Displays (OSD)
• Before Requesting Service • On-Screen Displays (OSD)
Tape Position Display Feature
Connection
• Special VCR Features • Copy Your Tapes (Dubbing)
Special VCR Features
Copying Your Tapes (Dubbing)
• To enable Quick play mechanism, the cylinder will
rotate for about 3 minutes. This reduces response
time from Stop to Play mode and from Play to Rewind
Search mode.
Table of Contents
Multi-Brand Control Feature ..................................... 2
Advanced Connections (Cable/DSS) ....................... 3
MTS Broadcast ........................................................ 4
VHS Hi-Fi Stereo System ......................................... 5
Tape Operation .................................................... 6, 7
Copying Your Tapes (Dubbing) ................................ 9
Special VCR Features ............................................ 10
On-Screen Displays (OSD) .................................... 11
Before Requesting Service .................................... 12
As an ENERGY STAR Partner, Panasonic
has determined that this product or product
model meets the ENERGY STAR guidelines
for energy efficiency.
See pages 2, 10
USE VCR : VCR KEY
Please read these instructions carefully before attempting to connect,
operate or adjust this product. Please save this manual.
Caution : Unauthorized exchanging and/or copying of copyrighted recordings may be
copyright infringement.
-9-
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
- 10 -
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
- 11 -
LSQT0547A
- 12 -
Audio/Video connection
If your TV has AUDIO IN and VIDEO IN terminals, you can connect your VCR
to them to receive higher quality picture and sound.
The Remote Control can be set to control some TV functions.
1 Find your TV Brand Code Number from those shown below.
2 Setup for TV control,
➛ hold down TV button,
➛ enter code with NUMBER keys.
IN FROM ANT.
VCR
TV
3
Confirm code entry,
AUDIO OUT
➛ press POWER to turn your TV on or off.
• See table below for controllable functions in each mode.
R
R
L
AUDIO IN
OUT TO TV
Notes
VIDEO IN
VCR
All
VOL UP/DOWN
TV
VCR/TV, PLAY, STOP, EJECT, SAP/Hi-Fi, DISPLAY,
FF, REW, PAUSE/SLOW, REC, SPEED, CM/ZERO,
RESET COUNTER, TAPE POSITION
POWER, INPUT, ENTER,
NUMBER keys, CH UP/DOWN,
VOL UP/DOWN
3
Set the VIDEO/TV selector of your TV (Monitor/Receiver) to “VIDEO.”
TV
STEREO
SAP
MONO
VCR
R
L
AUDIO
CATV
Sylvania ................................. 05
Sharp ............................... 06, 07
Sony ...................................... 08
Toshiba ................................. 09
Sanyo .................................... 10
Fisher .................................... 10
IN FROM ANT.
R
or
Panasonic ....................... 01, 02
Quasar ............................ 01, 02
RCA ...................................... 03
GE ......................................... 03
Zenith .................................... 04
Magnavox .............................. 05
You Can
TV
ANT
TV Brand Code Numbers
Cable Box)
VIDEO
L VHF/UHF
CABLE BOX
IN OUT
OUT TO TV
VIDEO
VHF/UHF
IN 1 OUT
JVC ....................................... 11
Hitachi ................................... 12
Mitsubishi ........................ 07, 13
Samsung ............................... 14
Gold Star ................... 15, 16, 17
IN OUT
R
AUDIO
L
VCR
■ Connect With Two Cable Boxes
Important Notes
VCR
• Due to changes in infra-red commands used by manufacturers, some brands have several codes.
If your unit does not respond to the first code, please try the next one.
• Some TV brands require you to turn on the power manually.
CABLE BOX
IN FROM ANT.
AUDIO
R
IN OUT
VIDEO
L VHF/UHF
OUT TO TV
IN 1 OUT
ANT
or
2-Way Splitter CABLE BOX
A/B Switch
CATV
OUT 1 OUT 2
IN OUT
IN 1 IN 2
• view any
(including
scrambled)
channel.
AUDIO OUT
• Arrow indicates selection.
R
R
L
VHF/UHF
R
AUDIO IN
• use VCR
Remote
Control to
select
channels
without using
Multi-brand
control feature.
You Can
3 Do a recording.
See p. 5 of “Basic Operations” Instruction book.
L
OUT TO TV
1
SEARCH
INDEX
PROGRAM END
ENTER INDEX NUMBER :1
USING 1- 9 KEYS
FORWARD SEARCH :FF
REVERSE SEARCH :REW
NEXT :SEARCH
EXIT :STOP
The following are possible audio broadcast types and on-screen displays.
The signal being received is indicated with an “ ” mark while the selected audio mode is
indicated with an arrow.
1 Start playback.
To display the broadcast signal being received,
➛ press DISPLAY*.
2 Press SAP/ Hi-Fi to display audio mode.
MTS Stereo and SAP broadcast
2
INDEX SEARCH
1 2 : 0 0AM
STEREO
SAP
MONO
STOP
SAP broadcast
1 2 : 0 0AM
STEREO
SAP
MONO
CH 02
0 : 00 : 00
SP
3
H I F I : L/R
HIFI : L
HIFI : R
NORMAL
STEREO
SAP
MONO
SELECT :
SET :
: ACT I ON
EXIT
Examples of Program End Search.
• Select “HIFI(L/R)” or
“HIFI(L)” or “HIFI(R)” to
listen to stereo recordings in
stereo sound.
Select “NORMAL” for
monaural sound.
Program 1
Program 2 or BLANK
the current tape position
Press SEARCH button
End Point
FF
Fig. 2
Program 1
To Calculate Index Number
Fig. 3
Example 1:
To go to rec. 2 from rec. 4, enter 3 and press
REW.
BLANK
Program 2
BLANK
Program 1
3
4
5
6
7
To go to rec. 6 from rec. 2, enter 4 and press
FF.
1
1 2 : 0 0AM
CH 02
0 : 00 : 00
SP
1 2 : 0 0AM
• Only tapes recorded in Hi-Fi stereo will playback with true stereo sound.
Standard stereo tapes will playback in monaural sound.
• To listen to Hi-Fi stereo playback, the VCR AUDIO (L/R) jacks must be connected to
a stereo TV or an external stereo amp and speakers. (See page 4.)
• If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.
• Hi-Fi and normal audio playback volume level may differ.
NOTE:
2
3
4
5
6
7
1 min Skip
2nd Press
2 min Skip
3rd Press
3 min Skip
• No indication appears.
To quickly return to a specified tape location.
1 Press DISPLAY during play
to display Counter.
2
PLAY
1 2 : 0 0AM
0 : 00 : 00
SP
Press RESET
COUNTER at desired
position to reset to
“0:00:00”.
Program 2
If search
exceeds a few
seconds in
BLANK area.
4 Press STOP.
5
REW
1 2 : 3 0AM
CH 02
0 : 30 : 30
SP
Upon locating end point,
➛ search continues 7 sec. past end point,
➛ tape rewinds to 10 sec. before end point,
➛ tape plays to end point and stops.
Example 2:
1st Press
3 Continue to record, playback, etc.
BLANK
FF
2
PLAY
Zero Search
End Point
the current tape position
Press SEARCH button
End Point
1
• Press CM/ZERO repeatedly to change
skip time as shown below.
Fig. 1
FF
Press SAP/ Hi-Fi repeatedly
to select desired mode.
1 Press CM/ZERO in Play mode.
Press
to select REPEAT PLAY
and press to set ON
or OFF.
ON : Play repeats at
tape end or if
unrecorded portion
over 30 sec. is
detected.
3 Press ACTION to return to normal screen.
Press CM/ZERO in Stop
mode to start ZERO
SEARCH.
• Unit will go into FF or
REW mode and stop at
the last point the
Counter was set to
0:00:00.
STOP
STEREO
SAP
MONO
STOP
Normal monaural sound broadcast.
:SEARCH
VCR
CLOCK CHANNEL
REPEAT PLAY
:OFF
REMOTE WARNING :ON
AUTO SHUT- OFF
:OFF
IDIOMA/LANGUE : ENGLISH
VCR’ S OUTPUT CH :3
the current tape position
Press SEARCH button
CH 02
0 : 00 : 00
SP
You Cannot
MONO broadcast
Press FF on the remote
to start PROGRAM
END SEARCH.
• To cancel, press
STOP or PLAY.
Notes
STOP
Secondary Audio Program (sub language) broadcast.
Select SAP audio mode for the sub language.
2
EXIT
Play begins at search
end. To search forward
or back 1 index, press
FF or REW on the
remote or VCR while
screen left is displayed
(10 sec.).
2
in Stop or Play mode.
SEARCH
PROGRAM END
VCR fast forwards (skips) over 1~3 minutes
of recorded tape.
1 Press ACTION to display menu.
1 Press SEARCH twice to display SEARCH
INDEX
Commercial Skip
Set to playback a recording over and over.
Locates end point of recording for continuity.
SEARCH START :FF
• To cancel, press
STOP or PLAY.
See p. 5 of “Basic Operations” Instruction book.
• Arrow indicates
selection.
Multi-channel Television Sound Stereo broadcast.
Select STEREO audio mode.
• If stereo broadcast is weak and display flickers, select
MONO audio mode for possibly better results.
Press SEARCH* to
display SEARCH in Stop
or Play mode, and then
press NUMBER keys to
select recording
number.
(Display disappears after 5 seconds.)
STOP
MTS Stereo broadcast
Program End Search
• To calculate number,
see below.
Press FF or REW on
the remote to start
search.
FORWARD SEARCH :FF
REVERSE SEARCH :REW
Notes
• record and view • view channel
other than
both scrambled
the one
and
selected for
unscrambled
any type of
channels if
recording.
additional
equipment is
TV
• do a Timer
added.
IN OUT
recording of
This connection
R AUDIO
a channel
requires: two
L
unless you
converter
VIDEO
select it at
boxes, an A/B
VHF/UHF
the cable
switch, and a 2box.
way splitter.
Index Search
Audio Mode for Playback
Receivable Broadcast Types
You Cannot
• record
scrambled
channels.
Press SAP/ Hi-Fi repeatedly
to select desired mode.
• Refer to “Receivable
Broadcast Types” on page 4.
Stereo Amplifier
Multi-channel Television Sound Stereo (main language)
and Secondary Audio Program (sub language)
broadcasts are being received simultaneously.
Select STEREO or SAP audio mode.
■ With a Cable Box (VCR
(Display disappears after 5 seconds.)
2
Notes
• Not all functions listed may be controllable.
• In TV mode, it may be necessary to press ENTER after pressing NUMBER keys for channel
selection.
1 Press SAP/ Hi-Fi to display audio mode.
INDEX
TV
Connect VCR’s L/R AUDIO OUT jacks to the TV’s L/R AUDIO IN jacks.
• You can use a TV connected to a Stereo amp and speakers instead of a Stereo TV.
Repeat Play
For each recording, an invisible index mark is placed on the tape. A program index and
program information are also included for timer recordings. These marks are used to
access or scan recordings.
INDEX
VCR
2
Make the Audio/Video Connection as shown on page 3.
Search System
INDEX
Unit
Mode
Connect the VCR’s VIDEO OUT jack to the TV’s VIDEO IN jack.
Audio Mode for Recording
Tape Operation
INDEX
1
After remote is set up, you can select VCR or TV for the desired function.
Press VCR or TV on the remote.
(Table below shows available unit buttons for each mode.)
VHF/UHF
VIDEO OUT
• Repeat setup after remote battery replacement.
• Remote will not control every TV made by the manufacturer listed. If you get no
response, your particular unit cannot be controlled. There are NO additional codes for
the products listed. If your product is not listed, then the remote is not compatible with
that product.
Using Multi-Brand Control
R
L
Connection
Tape Operation
1 2 : 3 1AM
CH 02
0 : 00 : 00
SP
• If Program End Search is started very
close to an index mark, that mark may be
skipped over.
• To cancel, press PLAY or STOP.
indicates start points of each recording.
Note
• If Index Search is started very close to an
index mark, that index mark may not be
counted in the search.
CH 02
0 : 00 : 00
SP
®
Equipped with
-TV Noise Reduction for true
®
-TV Noise Reduction is
MTS reproduction.
required for good stereo separation and audio
®
is a registered trademark, and is
fidelity.
®
Technology Licensing.
licensed by
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
-2-
LSQT0547A(Advanced Operations) - Back
-3-
-4-
-5-
-6-
-7-
• Tape Operation
Multi-Brand Control Setup
VHS Hi-Fi Stereo System
MTS Broadcast
• MTS Broadcast • VHS Hi-Fi Stereo System
Advanced Connections
• Multi-Brand Control Feature • Advanced Connections
Multi-Brand Control Feature
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement