Toshiba SD-R1202 Computer Drive User manual

Add to My manuals
16 Pages

advertisement

Toshiba SD-R1202 Computer Drive User manual | Manualzz

TOSHIBA

Storage Device Division

CD-RW/DVD-ROM

DRIVE

SD-R1202

Installation Instructions

with VOB InstantCD/DVD and

CyberLink PowerDVD

TM

Software

VERSION 2.0

MAY 2002

CD-RW/DVD-ROM DRIVE

Instruction Instructions

For the following Drive:

SD-R1202

TOSHIBA AMERICA INFORMATION SYSTEMS, INC.

STORAGE DEVICE DIVISION

9740 Irvine Blvd.

Irvine, CA 92618

Contents of this manual are subject to change without prior notice.

© 2002 TOSHIBA AMERICA INFORMATION SYSTEMS, INC.

All rights reserved

Printed in USA

P/N 460023-B0

Limited Warranty

Toshiba America Information Systems, Inc.

Storage Device Division

9740 Irvine Boulevard, Irvine, California 92618

1-949-583-3000

What does my limited warranty cover?

Toshiba America Information Systems, Inc. (“Toshiba”) warrants the Toshiba Storage

Product (“Product”) you have purchased from Toshiba or from a Toshiba authorized dealer is free from defects in materials or workmanship under normal use during the warranty period. This limited warranty extends only to the original purchaser and cannot be transferred to anyone. This limited warranty applies only to Products that are in cartons which are unopened on the date of purchase. During the warranty period,

Toshiba will, at its option, repair or replace defective parts with new parts or with reconditioned parts. Reconditioned parts will be equivalent or superior in performance to new parts. Either your sales receipt or proof of purchase is required to receive warranty service.

How long is my limited warranty coverage?

Product

2.5" Hard Disk Drives

1.8" Hard Disk Drives

DVD-ROM Drives

DVD-ROM/CD-RW Combo Drives

DVD-RAM Drives

Free parts, labor

3 years

1 year

1 year

1 year

1 year

Where is this limited warranty valid?

This limited warranty is valid only within the United States and Puerto Rico.

What is not covered by this limited warranty?

• Damage caused by improper installation or improper connection to a peripheral

(printer, etc.)

• Damage caused by an external electrical fault or an accident

• Damage caused by accident, misuse, abuse, neglect or improper maintenance

• Damage from use outside usage or storage parameters set forth in the product User’s

Guide

• Damage from use of parts not manufactured or sold by Toshiba

• Damage to or loss of any programs, data or removable storage media, or costs of recovering such programs or data

• Software or data loss that may occur during repair or replacement

• Product purchased from anyone other than Toshiba or a Toshiba authorized dealer

• Product purchased outside the United States and Puerto Rico

• Modifications to product not approved in writing by Toshiba

• Service made necessary by use of incompatible third party products

• Routine cleaning, or normal cosmetic and mechanical wear

• Damage or loss during transit to Authorized Service Partner

Toshiba’s sole obligations with respect to software distributed under the Toshiba brand name are set forth in the applicable end-user license agreement. Unless otherwise stated in writing, non-Toshiba software is provided on an “as is” basis by Toshiba.

Any service or repair for items not covered by this limited warranty shall be at

Toshiba’s or its Authorized Service Partner’s rates and terms then in effect.

How do I obtain warranty service?

In order to obtain warranty service, please contact Toshiba’s authorized service center.

Details on contacting Toshiba’s authorized service center can be found at www.sdd.toshiba.com.

Disclaimer and limitation of remedy

ALL OTHER EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT, INCLUDING

THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE AND/OR NONINFRINGEMENT OF THIRD PARTY RIGHTS, ARE HEREBY

DISCLAIMED. TOSHIBA EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN

THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY

LAW ARE LIMITED IN DURATION TO THE TERM OF THIS EXPRESS LIMITED WAR-

RANTY. SOME COUNTRIES, STATES OR JURISDICTIONS DO NOT ALLOW THE EXCLU-

SION OF IMPLIED WARRANTIES OR LIMITATIONS ON HOW LONG AN IMPLIED WAR-

RANTY LASTS, SO THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO

YOU. YOU MUST READ AND FOLLOW ALL SET-UP AND USAGE INSTRUCTIONS IN THE

APPLICABLE USER GUIDES AND/OR MANUALS ENCLOSED. IF YOU FAIL TO DO SO,

THIS PRODUCT MAY NOT FUNCTION PROPERLY AND YOU MAY LOSE DATA OR SUFFER

OTHER DAMAGE. TOSHIBA, ITS AFFILIATES AND SUPPLIERS DO NOT WARRANT THAT

OPERATION OF THIS PRODUCT WILL BE UNINTERRUPTED OR ERROR FREE.

IF THIS PRODUCT FAILS TO WORK AS WARRANTED ABOVE, YOUR SOLE AND EXCLU-

SIVE REMEDY SHALL BE REPAIR OR REPLACEMENT. IN NO EVENT WILL TOSHIBA, ITS

AFFILIATES OR SUPPLIERS BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY

DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT. THIS LIMITATION

APPLIES TO DAMAGES OF ANY KIND WHATSOEVER INCLUDING (1) DAMAGE TO, OR

LOSS OR CORRUPTION OF, YOUR RECORDS, PROGRAMS, DATA OR REMOVABLE

STORAGE MEDIA, OR (2) ANY DIRECT OR INDIRECT DAMAGES, LOST PROFITS, LOST

SAVINGS OR OTHER SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL

DAMAGES, WHETHER FOR BREACH OF WARRANTY, CONTRACT, TORT OR OTHER-

WISE, OR WHETHER ARISING OUT OF THE USE OF OR INABILITY TO USE SUCH

PRODUCT AND/OR THE ENCLOSED USER GUIDES AND/OR MANUALS, EVEN IF

TOSHIBA, OR AN AUTHORIZED TOSHIBA REPRESENTATIVE, AUTHORIZED SERVICE

PARTNER OR DEALER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES

OR OF ANY CLAIM BY ANY OTHER PARTY.

SOME STATES OR JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF

INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR SOME PRODUCTS, SO THE ABOVE

EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY

GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS

WHICH VARY FROM COUNTRY/STATE/JURISDICTION TO COUNTRY/STATE/JURISDIC-

TION.

Protection of Stored Data

For your important data, please make periodic back-up copies of all the data stored on the hard disk or other storage devices as a precaution against possible failures, alteration, or loss of the data.

IF YOUR DATA IS ALTERED OR LOST DUE TO ANY TROUBLE,

FAILURE OR MALFUNCTION OF THE HARD DISK DRIVE OR OTHER STORAGE DEVICES

AND THE DATA CANNOT BE RECOVERED, TOSHIBA SHALL NOT BE LIABLE FOR ANY

DAMAGE OR LOSS OF DATA, OR ANY OTHER DAMAGE RESULTING THEREFROM.

WHEN COPYING OR TRANSFERRING YOUR DATA, PLEASE BE SURE TO CONFIRM

WHETHER THE DATA HAS BEEN SUCCESSFULLY COPIED OR TRANSFERRED. TOSHIBA

DISCLAIMS ANY LIABILITY FOR THE FAILURE TO COPY OR TRANSFER THE DATA

CORRECTLY.

Critical Applications

The Product you have purchased is not designed for any “critical applications.” “Critical applications” means life support systems, medical applications, connections to implanted medical devices, commercial transportation, nuclear facilities or systems or any other applications where product failure could lead to injury to persons or loss of life or catastrophic property damage. ACCORDINGLY, TOSHIBA, ITS AFFILIATES AND SUPPLI-

ERS DISCLAIM ANY AND ALL LIABILITY ARISING OUT OF THE USE OF THE PRODUCT

IN ANY CRITICAL APPLICATIONS. IF YOU USE THE PRODUCT IN A CRITICAL APPLICA-

TION, YOU, AND NOT TOSHIBA, ASSUME FULL RESPONSIBILITY FOR SUCH USE.

Table of Contents

Checking your Kit Packaging ...................................................................... 1

System Requirements .................................................................................... 1

Setting Jumpers ............................................................................................. 2

Placing CD-RW/DVD-ROM inside your computer ...................................... 2

Connecting Cables ........................................................................................ 3

IDE BUS (data) Cable ............................................................................... 3

Power Cable .............................................................................................. 4

Audio Cable .............................................................................................. 4

Completing Installation ................................................................................ 5

ATAPI CD/DVD Software Driver .............................................................. 5

VOB InstantCD/DVD Software ................................................................. 5

CyberLink Power DVD ............................................................................. 6

CD-RW/DVD-ROM Front Panel ................................................................... 6

CD-RW/DVD-ROM Back Panel .................................................................... 6

Specifications ................................................................................................ 7

Technical Support ......................................................................................... 8

LASER CAUTION

This appliance contains a laser system and is classified as a "CLASS 1 LASER PRODUCT". To use this model properly, read this Owner's Manual carefully and keep this manual for future reference. In case of any trouble with this model, please contact your nearest "Authorized Repair Center". To prevent direct exposure to the laser beam,

do not try to open the enclosure

CAUTION!

• REFLECTIVE OBJECTS SHOULD NOT BE PLACED IN THE DISK SLOT

DUE TO POSSIBLE HAZARDOUS RADIATION EXPOSURE.

• USE OF CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER THAN

SPECIFIED IN THIS MANUAL MAY RESULT IN HAZARDOUS RADIA-

TION EXPOSURE.

Version

01

02

Date Published

January 2002

May 2002

Revised Contents

Initial release

Address/Phone Number changes

Congratulations on your purchase of a Toshiba CD-RW/DVD-ROM drive and Kit.

The following information will help you in the simple installation of your new

CD-RW/DVD-ROM drive.

CHECKING YOUR KIT PACKAGING

Please unpack your CD-RW/DVD-ROM kit, and assure that you have the following items:

! Toshiba CD-RW/DVD-ROM Drive

! CD-R Blank Media CD

! CD-RW Blank Media CD

! CyberLink PowerDVD

™ Software CD

! VOB InstantCD/DVD Software CD

! CD-RW/DVD-ROM Installation Instructions (this manual)

! Quick Start Guide

! Mounting screws

(4)

! IDE BUS cable

! DVD/CD audio cable

Additional items you may need that are not included in the kit are:

! Phillips Screwdriver

! Mounting hardware (i.e. some computer systems use mounting rails).

SYSTEM REQUIREMENTS

The CD-RW/DVD-ROM kit requires the following:

✔ At least 55MB of free hard disk space

✔ At least 32MB of RAM

✔ *Pentium II processor at 266MHz or higher or....

*Celeron 300A processor or higher or....

*K6-2 processor at 300MHz or higher

✔ Display card supporting DirectDraw

✔ 16-bit or better sound card

✔ Microsoft

Windows 95 or higher

✔ Amplified stereo speakers

* These requirements are only required if you are using the CyberLink PowerDVD ™ software for movie playback. Toshiba’s CD-RW/DVD-ROM drive will work as a CD-ROM, DVD-ROM and CD-RW when using a lower speed Pentium system.

1

The following steps must be performed to properly install your CD-RW/DVD-

ROM.

! Set drive’s jumpers

! Connect audio cable

! Attach IDE BUS cable

! Connect power cable

! Mount CD-RW/DVD-ROM

! Install CyberLink PowerDVD

software (used for viewing DVD movies)

! Install VOB InstantCD/DVD software (used for recording CDs)

SETTING JUMPERS

The mode select jumpers are six (6) straight pins located on the rear of the CD-RW/

DVD-ROM. By placing a jumper on the pins, you can select the following functions:

CS: – Drive is configured using host interface signal CSEL

SL: – Configures drive as Slave

MA: – Configures drive as Master (default mode)

C

S

S

L

M

A

Mode Select Jumpers

In most installations, jumper should remain in MA (Master) position (factory default). It is recommended that you install your CD-RW/DVD-ROM only on the secondary IDE BUS. If you are installing on primary IDE BUS, your hard drive would then be the Master, and you should set your CD-RW/DVD-ROM to the

Slave position (SL).

PLACING CD-RW/DVD-ROM INSIDE YOUR COMPUTER

Now that you have set your drive’s jumpers, you are ready to install your

CD-RW/DVD-ROM inside your computer.

2

IMPORTANT: Disconnect power from your computer system before beginning installation.

1. Remove computer cover and faceplate if required (refer to your computer system’s manual for removal information).

2. If the CD-RW/DVD-ROM is replacing a CD-ROM, disconnect all connectors and remove the CD-ROM presently installed in your system.

3. Your Toshiba CD-RW/DVD-ROM can be placed in any free half-height drive slot at the front of your computer. (It can be mounted horizontally or vertically.)

4. Carefully start sliding the CD-RW/DVD-ROM into the opening with the disc tray facing the front of the computer. Before you push the drive all the way in you will need to connect the IDE BUS cable, audio cable and the power cable to the back of the drive.

CONNECTING CABLES

Cable Locations on Rear of CD-RW/DVD-ROM

IDE BUS (Data) Cable - Most computer system have a primary and secondary

IDE BUS cable already installed (an IDE BUS cable is include with your kit if your system does not have a secondary IDE BUS cable).

If you are replacing a CD-ROM: connect the CD-RW/DVD-ROM drive using the

BUS cable that the CD-ROM was connected to. Insure that the jumper setting of the CD-RW/DVD-ROM is the same as the CD-ROM drive you are replacing.

If the CD-RW/DVD-ROM is not replacing a CD-ROM and/or is in addition to a

CD-ROM: locate the secondary IDE BUS cable in your system. If your system does not have a secondary IDE BUS cable installed, you will need to install the

IDE BUS cable that was included with your kit.

Installing secondary IDE BUS cable: locate the secondary IDE BUS connector on your system’s motherboard (refer to your system’s documentation for location). Connect one end of the IDE BUS cable to motherboard, assuring that it is keyed properly and that cable’s colored edge is aligned with Pin 1.

3

4

Connect secondary IDE BUS cable to CD-RW/DVD-ROM drive, assuring that pin

1 of the cable (side with red stripe) is connected to pin 1 on the drive.

• If the CD-RW/DVD-ROM is the only drive connected on the secondary IDE

BUS cable: connect drive to the last set of pins on IDE BUS cable.

• If there is a device (i.e. CD-ROM) connected to the secondary IDE BUS

cable: connect CD-RW/DVD-ROM to the open middle connector . The CD-

RW/DVD-ROM drive should then be jumpered to SL (slave) position.

If the CD-RW/DVD-ROM is to be the slave on the Primary BUS: connect the CD-

RW/DVD-ROM to the open connector on the primary IDE BUS cable. The CD-RW/

DVD-ROM drive should be jumpered to the SL (slave) position. Note: the primary

IDE BUS cable, in most cases, will be connected to your hard drive. The hard drive will be the Master on the primary BUS.

Power Cable - Inside your computer system, locate an unused power supply cable.

Connect the power cable to the power socket at the back of the CD-RW/DVD-

ROM. One side of the plug has chamfered edges, so the power connector fits only one way so be sure to insert the DC power plug in the correct direction. Push plug completely into the socket making sure the plug fits correctly.

Audio Cable - Connecting your CD-RW/DVD-ROM to your sound card allows you to play audio CDs on your computer (speakers or headphones are also needed).

If the CD-RW/DVD-ROM is in addition to a CD-ROM: If you choose to have both a CD-ROM and CD-RW/DVD-ROM installed in your system, in most circumstances, only one audio cable can be used (there are some sound cards that will allow you to have two audio connections). You must decide which device you would like to hear audio from and connect the audio cable from the sound card to the CD-ROM or CD-RW/DVD-ROM (DVD audio is transmitted through the data cable, not the audio cable).

If the CD-RW/DVD-ROM is to be the only CD-ROM device in your system:

• If replacing a CD-ROM that had an audio cable connection: connect CD-

RW/DVD-ROM drive to the audio cable that the CD-ROM was connected.

Cable connects to the analog audio connector at the left rear of the CD-RW/

DVD-ROM (see Cable Location photo on page 3 for location).

• If you do not have an audio cable presently in your system: connect the CD-

RW/DVD-ROM using the audio cable that was included with this kit. Connect one end to your sound card and the other end to the analog audio connector at the left rear of the CD-RW/DVD-ROM (see Cable Location photo on page 3 for location). Refer to the instructions which came with your sound card for details on any sound-driver software required.

COMPLETING INSTALLATION

After you have connected all the necessary cables, push the CD-RW/DVD-ROM completely into the computer’s drive slot. Mount the drive per your computer’s instructions using the screws included in your kit. If you are using other screws, assure that the screw length does not exceed 3±0.5mm (measured from outside surface of side or bottom of CD-RW/DVD-ROM to tip of screw). Replace the computer cover and all outer screws.

ATAPI CD/DVD Software Driver:

Toshiba’s CD-RW/DVD-ROM drives do not require any unique device drivers for

Windows '95/'98/2000/Me/XP/NT. After installing your drive and re-booting, your system should recognize your drive. Win '95/'98/2000/Me/XP/NT operating systems support all Toshiba ATAPI CD-RW, CD-ROM and DVD-ROM drives natively.

VOB InstantCD/DVD Software:

Before installing VOB software it is recommended you visit VOB’s website to check for any software updates (http://www.vobinc.com).

To install software insert the installation CD into your newly installed drive. If

Autorun” is enabled on your system, the Installation window will appear automatically. If it does not appear, go to Windows Start menu, select “Run” and type d:\setup.exe (substitute the appropriate letter of your new drive for d:). From the Installation window select InstantCD/DVD and follow the installation instructions that appear on your screen. For additional information on this software, please refer to the documentation found on the VOB “InstantCD/DVD” CD.

InstantDisc - This easy to use software enables you to create your own CDs.

InstantBackup - Easy to use backup solution with support for CD-R(W), DVD-

RAM, and DVD-R(W) drives. Includes compression, encryption, spanning and scheduled backups.

InstantCopy - Professional CD Duplication program including DAO-RAW support, easy to use profiles and On-the-Fly Data Processing.

InstantWrite - The only complete UDF packet writing software. Supports CD-

R(W), DVD-RAM and DVD-R and all UDF levels up to 2.01. With easy to use format wizard and Defragmentation utility.

InstantMusic - Easy to use 16 track harddisc recording studio. Song composing made easy. Includes real-time mixer, about 1000 high quality samples and various effect filters.

InstantVideo - Creates VideoCDs- and SuperVideoCDs that can be played back in almost any DVD-Player. AVIs are automatically encoded to the correct MPEG-1 format.

5

CyberLink PowerDVD:

*Before installing CyberLink software it is recommended you visit CyberLink’s website to check for any software updates (http://www.gocyberlink.com).

CyberLink PowerDVD ™ is a high-quality, pure-software DVD player that brings high-quality movies and karaoke into your multimedia PC. You can playback high resolution DVD titles or MPEG-2 files with superb MPEG-2 video and Dolby

AC-3 audio quality.

To install, insert CyberLink PowerDVD ™ into your newly installed CD-RW/DVD-

ROM. Go to Windows Start menu, select “Run” and type d:\setup.exe (substitute the appropriate letter of your CD-RW/DVD-ROM drive for d:). Follow the installation instructions on screen. For additional information on using this software, please refer to the PowerDVD ™ Help file (if you have opened PowerDVD ™ software, click “?”).

CD-RW/DVD-ROM MEDIA

After installing the VOB and CyberLink software your system is ready to use.

Some important things to remember when using your CD-RW/DVD-ROM Drive:

! Do not insert more than one CD or DVD disc into the drive at a time.

! Do not insert anything other than a CD or DVD disc into drive.

! Use media that is the correct size and shape.

! Use media that meets write/read requirements listed in the Specifications

(see page 14).

EMERGENCY EJECT

CAUTION!

The following procedure is intended only as a last resort when pressing the Eject button fails to open the CD-RW/DVD tray.

Do not use Emergency Eject Procedure while the drive is in operation.

Inserting Bar to Eject DVD Tray

1.

Turn CD-RW/DVD-ROM drive power OFF.

2.

Insert a solid bar (i.e. large paper clip*) into Emergency Eject hole and push in as shown in the picture below.

3.

CD-RW/DVD-ROM tray will open/eject.

This procedure cannot be repeated without cycling the drive’s power. After the media is removed and the loading tray is closed, the tray will not reopen without first turning the power ON/OFF.

* Use a bar that is less than 1.5mm in diameter. Do not insert more than 50mm in depth as this may damage the drive.

CD-RW/DVD-ROM FRONT PANEL

The photo below illustrates the following features of the SD-R1202 CD-RW/

DVD-ROM front panel:

"

Loading Tray

$

Busy Light

#

%

Eject Button

Emergency Eject Hole

CD-RW/DVD-ROM BACK PANEL

The photo below illustrates the following features of the SD-R1202 CD-RW/DVD-

ROMs back panel:

"

Digital Audio Out Connector

$

Analog Audio Out Connector

#

Mode Select Jumper

%

ATAPI Connector

&

Power Connector

SPECIFICATIONS

DATA CAPACITY

ROTATIONAL SPEED

DVD

2,048 Byte/Block

CD

2,048 Byte/Block (mode 1)

2,336 Byte/Block (mode 2)

DVD : 7,580rpm

(12X - Single Layer)

CD-ROM, CD-R: 8,561rpm

5,053rpm

(3.3-8X -Dual Layer)

(13.8 - 40X)

DVD-R (Ver 2), DVD-RW, CD-RW: 3,281rpm (8.6 - 20X)

DVD-Video : 2,780rpm

(2-4.8X)

CD-DA Transfer: 3,200rpm

DVD-R (Ver 1): 3,200rpm

(2 - 4.8X)

CD-R (Write): 3,400-

5,940rpm (12, 16X)

1,700-3,960rpm (8X CLV)

(12.7 - 16X)

CD-DA, Video-CD:

1,200 - 2,000rpm (4 - 6X)

2,550-5,940rpm (12X CLV)

High Speed CD-RW (write):

850 - 1,980 rpm (4X CLV)

CD-RW (write):850 - 1,980 rpm

(4XCLV)

850-1,980 rpm (4X CLV)

2,125 - 4,950 (10X CLV)

SUSTAINED DATA

TRANSFER RATE

DVD: 6,682-16,200KB/s

DVD(dual layer): 4,432-10,800KB/s

DVD-VIDEO, DVD-R, DVD-RW: 2,704-6,536KB/s

CD-RW: 1,294-3,000KB/s (mode 1) 1,475-3,422KB/s (mode 2)

CD: 2,588-6,000KB/s (mode 1) 2,950-6,843KB/s (mode 2)

ACCESS TIME (Typ.)

DVD

CD

DATA BUFFER

POWER SUPPLY

MTBF

Avg. Random Access Avg Random Seek Avg. Full Stroke

130ms

110ms

120ms

105ms

210ms

180ms

2,048 KByte

+5v, +12v

100,000 hours

DIMENSIONS (Wx H x D) 5.7” x 1.6” x 7.6” (146mm x 41.5mm x 193mm)

WEIGHT 2.03lbs ( 0.92kg)

MOUNTING ORIENTATION ±10° vertical / ±20° horizontal

APPLICABLE WRITE DISC CD-DA, CD+(E)G, CD-MIDI, CD-ROM, CD-ROM XA,

MIXED MODE CD, CD-I, CD-I Bridge (Photo-CD, Video-

CD), Multi-session CD (Photo-CD, CD-Extra, Portfolio)

APPLICABLE READ DISC DVD-ROM, DVD-R, DVD-RW, CD-DA, CD+(E)G, CD-MIDI,

CD-TEXT, CD-ROM, CD-ROM XA, CD-I, CD-I Bridge

(Photo-CD, Video-CD), Multi-session CD (Photo-CD, CD-

Extra, CD-R, CD-RW, Portfolio), CD-R, CD-RW

TECHNICAL SUPPORT

Technical support can be obtained by calling 805/644-6350 or by sending an email to: [email protected] or visiting our website at:

http://www.sdd.toshiba.com

7

8

460023-B0

P/N 460023-B0

advertisement

Related manuals