hd cctv dvr user manual
HD CCTV DVR
USER MANUAL
 2MP ~ 5MP Video Recording
Please read instructions thoroughly before operation and retain it for future reference.
For the actual display & operation, please refer to your DVR in hand.
Complete user manual download: www.surveillance-download.com/user/z404.swf
404_2404_1304_408_308_1308_d1308_416_416t_316_1316_d1316_manual_V1.2
IMPORTANT SAFEGUARD
CAUTION
RISK OF ELECTRIC SHOCK
CAUTION:
To reduce the risk of electric shock, do not expose this apparatus to rain or moisture. Only operate this apparatus
from the type of power source indicated on the label. The company shall not be liable for any damages arising out
of any improper use, even if we have been advised of the possibility of such damages.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
This exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the appliance.
All lead-free products offered by the company comply with the requirements of the European law on the Restriction of Hazardous
Substances (RoHS) directive, which means our manufacture processes and products are strictly “lead-free” and without the
hazardous substances cited in the directive.
The crossed-out wheeled bin mark symbolizes that within the European Union the product must be collected separately at the
product end-of-life. This applies to your product and any peripherals marked with this symbol. Do not dispose of these products as
unsorted municipal waste. Contact your local dealer for procedures for recycling this equipment.
This apparatus is manufactured to comply with the radio interference requirements.
Federal Communications Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
Trademark Acknowledgements
(EagleEyes) - The trademark application is filed and under process in the U.S. and other countries.
iPhone®, iPad® and iOS® are the registered trademark of Apple Inc., and Apple holds the intelligential property rights to the iPhone, iPad and
iOS content.
Microsoft®, Windows®, Internet Explorer®, Google Chrome™ & QuickTime® mentioned in this document are the registered trademarks of their
respective holders.
Disclaimer
The information in this manual was current when released. We reserve the right to revise or remove any content in this manual at any time. We
do not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of this manual. For the actual display
& operation, please refer to your DVR in hand. The content of this manual is subject to change without notice.
Grounding
This is a Safety Class 1 Product (provided with a protective earthing ground incorporated in the power cord). The mains plug shall only be
inserted in a socket outlet provided with a protective earth contact. Any interruption of the protective conductor inside or outside of the instrument
is likely to make the instrument dangerous. Intentional interruption is prohibited.
Water & Moisture
Do not expose this product to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the product.
MPEG4 Licensing
THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND
NON-COMMERCIAL USE OF A CONSUMER FOR (i) ENCODING VIDEO IN COMPLIANCE WITH THE MPEG-4 VISUAL STANDARD
(“MPEG-4 VIDEO”) AND/OR (ii) DECODING MPEG-4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND
NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE MPEG-4
VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT
RELATING TO PROMOTIONAL INTERNAL AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA, LLC. SEE
HTTP://WWW.MPEGLA.COM.
GPL Licensing
This product contains codes which are developed by Third-Party-Companies and which are subject to the GNU General
Public License (“GPL”) or the GNU Lesser Public License (“LGPL”).
The GPL Code used in this product is released without warranty and is subject to the copyright of the corresponding
author.
Further source codes which are subject to the GPL-licenses are available upon request.
We are pleased to provide our modifications to the Linux Kernel, as well as a few new commands, and some tools to get
you into the code. The codes are provided on the FTP site, and please download them from the following site or you
can refer to your distributor:
http://download.dvrtw.com.tw/GPL/DVR/TVI/linux-3.3-fa.tgz
TABLE OF CONTENTS
1. HARDWARE OVERVIEW................................................................................................................ 1 1.1 Package Content ...................................................................................................................................................1 1.2 Front Panel ............................................................................................................................................................1 1.3 Rear Panel .............................................................................................................................................................2 2. CONNECTION AND SETUP ........................................................................................................... 4 2.1 SATA Hard Disk Installation....................................................................................................................................4 2.2 Camera Connection ...............................................................................................................................................6 2.2.1 Normal Camera .............................................................................................................................................6 2.2.2 HD CCTV Camera Series ..............................................................................................................................6 2.2.3 Other brand’s speed dome camera ...............................................................................................................7 2.2.4 IP Camera......................................................................................................................................................7 2.3 DVR Power On ......................................................................................................................................................8 3. FOR INITIAL USE............................................................................................................................ 9 3.1 Setup Wizard .........................................................................................................................................................9 3.2 Clear Hard Disk .................................................................................................................................................... 11 3.3 Change User Name and Password ......................................................................................................................12 4. USER INTERFACE ........................................................................................................................ 13 4.1 DVR Access .........................................................................................................................................................13 4.2 Live Page .............................................................................................................................................................13 4.2.1 DVR Status ..................................................................................................................................................13 4.2.2 Channel Status ............................................................................................................................................14 4.2.3 Record-related Icons ...................................................................................................................................14 4.3 Quick Menu Bar ...................................................................................................................................................15 4.4 Main Menu ...........................................................................................................................................................15 5. FREQUENTLY-USED FUNCTIONS .............................................................................................. 16 5.1 Key Lock / Unlock ................................................................................................................................................16 5.2 User Level Creation .............................................................................................................................................16 5.3 PTZ Control..........................................................................................................................................................18 5.4 Playback ..............................................................................................................................................................19 5.4.1 Playback Control..........................................................................................................................................20 5.4.2 Event Search ...............................................................................................................................................20 5.4.3 Audio Playback ............................................................................................................................................20 5.5 Video Backup .......................................................................................................................................................20 5.6 Video Playback on PC (.dv5) ...............................................................................................................................21 5.6.1 Convert the file format to AVI .......................................................................................................................22 5.7 Digital Zoom .........................................................................................................................................................22 6. MAIN MENU .................................................................................................................................. 23 6.1 QUICK START .....................................................................................................................................................23 6.1.1 GENERAL ...................................................................................................................................................23 6.1.2 TIME SETUP ...............................................................................................................................................25 6.1.3 DAYLIGHT ...................................................................................................................................................25 6.1.4 EaZy ............................................................................................................................................................26 6.2 SYSTEM ..............................................................................................................................................................26 6.2.1 ACCOUNT ...................................................................................................................................................26 6.2.2 TOOLS.........................................................................................................................................................27 6.2.3 SYSTEM INFO ............................................................................................................................................28 6.2.4 ONLINE .......................................................................................................................................................30 6.2.5 BACKUP DATA ............................................................................................................................................30 6.2.6 BACKUP LOG .............................................................................................................................................32 6.3 EVENT INFORMATION .......................................................................................................................................33 6.3.1 QUICK SEARCH .........................................................................................................................................33 6.3.2 EVENT SEARCH .........................................................................................................................................33 6.3.3 HDD INFO ...................................................................................................................................................34 6.3.4 EVENT LOG ................................................................................................................................................34 6.4 ADVANCED CONFIG...........................................................................................................................................35 6.4.1 CAMERA .....................................................................................................................................................35 6.4.2 DETECTION ................................................................................................................................................36 6.4.3 ALERT .........................................................................................................................................................38 6.4.4 NETWORK ..................................................................................................................................................39 6.4.5 DISPLAY ......................................................................................................................................................41 6.4.6 RECORD .....................................................................................................................................................42 6.4.7 DEVICES .....................................................................................................................................................43 6.4.8 DCCS ..........................................................................................................................................................44 6.4.9 IVS ...............................................................................................................................................................44 6.4.10 NOTIFY .....................................................................................................................................................49 6.4.11 JOYSTICK .................................................................................................................................................54 6.5 SCHEDULE SETTING .........................................................................................................................................54 6.5.1 RECORD / DETECTION / ALARM IN / ALARM OUT / PUSH VIDEO / BUZZER ........................................54 6.5.2 REGULAR REPORT ...................................................................................................................................55 6.5.3 AUTO BACKUP ...........................................................................................................................................55 6.5.4 REGULAR REBOOT ...................................................................................................................................57 7. REMOTE OPERATION.................................................................................................................. 58 7.1 Web Browser .......................................................................................................................................................58 7.1.1 IVS Statistics ................................................................................................................................................60 7.1.2 PTZ Panel ....................................................................................................................................................61 7.2 Mobile Devices .....................................................................................................................................................62 7.2.1 Prerequisites ................................................................................................................................................62 7.2.2 Where to download ......................................................................................................................................62 7.2.3 Manual Setup ..............................................................................................................................................62 APPENDIX 1 SPECIFICATIONS ....................................................................................................... 64 APPENDIX 2 PUSH VIDEO CONFIGURATION ............................................................................... 72 A2.1 Alarm Sensor Connection ..................................................................................................................................72 A2.2 Configuration .....................................................................................................................................................73 APPENDIX 3 SET PUSH VIDEO....................................................................................................... 74 A3.1 Prerequisite .......................................................................................................................................................74 A3.2 Enable Push Video ............................................................................................................................................75 A3.2.1 From iOS Mobile Device (iPhone / iPad) ...................................................................................................75 A3.2.2 From Android Mobile Device .....................................................................................................................76 APPENDIX 4 COMPATIBLE USB FLASH DRIVE LIST ................................................................... 77 APPENDIX 5 COMPATIBLE SATA HDD LIST .................................................................................. 78 APPENDIX 6 MAIN MENU STRUCTURE ......................................................................................... 79 APPENDIX 7 DVR BATTERY REPLACEMENT ............................................................................... 81 APPENDIX 8 EAZY NETWORKING ................................................................................................. 82 A8.1 Via EagleEyes on iOS / Android Device .......................................................................................................82 A8.2 Via Internet Explorer on PC / Laptop ............................................................................................................87 A8.3 Cloud Icons ..................................................................................................................................................92 HARDWARE OVERVIEW
1. HARDWARE OVERVIEW
Note: The functions on the front panel and rear panel may vary, depending on the model you have.
1.1 Package Content

Standard Package
 DVR
 HDD screws
 Adapter & power cord
 Quick Start

Optional Accessories
 I/O terminal block
 IR Remote Controller
 USB Mouse
1.2 Front Panel
1)
LED Indicators
DVR is powered on.
The hard disk is reading or recording.
An alarm is triggered.
Timer recording is on.
Under playback status.
2)
CH1 ~ 16 / 1 ~ 8 / 1 ~ 4
Press the channel number buttons to select the channel to display.
3)
Press to show the 4 channel display mode.
4)
SEQ
Press to display each channel in full screen one by one starting from CH1. When the last channel is displayed, it
will repeat from CH1 again. To exit this mode, press SEQ again.
5)
SLOW
In the playback mode, press to show slow playback.
6)
ZOOM
Press to enlarge the picture of selected channel in the FRAME or FIELD recording mode.
7)
PLAY
Press to playback the latest recorded data.
8)
LIST (Event List Search)
Press to quickly search the recorded files by event types, or select FULL to show all the event logs.
To quickly search the time you want, select QUICK SEARCH. For details, please refer to “5.4.2 Event Search”
at page 20.
9)
ENTER
Press ENTER to confirm the setting.
10) MENU
Press MENU to enter the main menu.
1
HARDWARE OVERVIEW
11) ▲ ( / PAUSE) / ▼ ( / STOP) / ◄ ( / REW) / ► ( / FF)
Press ▲ / ▼ / ◄ / ► to move up / down / left / right.
In the playback mode:
Press ▲ to pause playback.
Press ▼ to stop playback.
Press ► to fast forward.
Press ◄ to fast rewind.
12) AUDIO (SLOW + ZOOM)
Press SLOW + ZOOM to select live or playback audio from audio channel 1~4.
Live audio from audio channel 1~4
(indicated in white).
Playback audio from audio channel 1~4
(indicated in yellow).
Audio channel unselected
13) P.T.Z. (
Press
+ SEQ)
+ SEQ at the same time to enter / exit the PTZ control mode.
14) USB port
There are two USB ports on the front panel, one for connecting your USB mouse for mouse control, and the other
one for connecting your USB flash drive for video backup.
Note: It’s not allowed to have two USB mice or two USB flash drives connected on the front panel.
Note: For the compatible USB flash drive list, please refer to “APPENDIX 4 COMPATIBLE USB FLASH
DRIVE LIST” at page 77.
1.3 Rear Panel
1)
VIDEO IN
Connect to the video connector of a camera.
Note: The DVR will automatically detect the video system of the camera, please make sure that the
cameras are properly connected to the DVR and power-supplied before the DVR is turned on.
2)
VIDEO OUT
Connect to a CRT monitor for main or spot monitor output.
3)
AUDIO IN
Connect to the audio connector of a camera if the camera supports audio recording.
Note: To make a video backup with audio, make sure the camera which supports the audio function is
connected to the video-in channel and audio-in channel. For example, the audio data from audio
CH1 will be recorded with the video data from video CH1.
For 16CH models, the audio CH1 ~ CH4 are corresponding to video CH1 ~ CH4 respectively.
4)
AUDIO OUT
Connect to a speaker with 1 mono audio output.
5)
HDMI
Connect to the HDMI port of the monitor which supports HDMI video output for main or spot monitor output.
6)
VGA
Connect to the VGA port of the monitor which supports VGA video output for main or spot monitor output.
7)
IR
Connect the IR receiver extension line for remote control.
2
HARDWARE OVERVIEW
8)
eSATA
This port is used to connect a storage device supporting eSATA interface; for instance, an external hard disk or a
disk array.
Note: Please purchase a disk array supporting Linux system to ensure your DVR to work properly.
Note: If the disk array is not connected or detected well, check the mode of your disk array, or do a reset
default on your disk array and try again.
9)
USB port
There are two USB ports on the front panel, one for connecting your USB mouse for mouse control, and the other
one for connecting your USB flash drive for video backup.
Note: It’s not allowed to have two USB mice or two USB flash drives connected on the front panel.
Note: For the compatible USB flash drive list, please refer to “APPENDIX 4 COMPATIBLE USB FLASH
DRIVE LIST” at page 77.
10) External I/O (Alarm IN / Alarm Out / RS485)
These ports are used to connect external devices (such as speed dome cameras or external alarm, etc).
11) LAN
Connect to Internet by LAN cable.
12) DC IN
Connect to the supplied adapter.
13)
Power Switch
Switch to “—” to turn on the power, and “” to turn off the power.
3
CONNECTION AND SETUP
2. CONNECTION AND SETUP
Before the DVR is powered on, make sure you have installed a hard disk, connected at least one camera and a
HDMI monitor. For details, please refer to the following sections.
Note: The DVR is designed to automatically detect the video system of the connected cameras (NTSC or
PAL). To make sure the system detection is correct, please check if the cameras are connected to
the DVR and power-supplied before the DVR is powered on.
2.1 SATA Hard Disk Installation
At least a hard disk is necessary for the recorder to save video footage, and firmware upgrade might be failed if
there’s no hard disk installed in this recorder.
Either of the following two types of hard disk installation is applicable for your DVR model. Please check the
instructions below to see which installation method is the right one for your DVR to install a hard disk.
 Type 1
Note: Here takes an 8CH model as an example of how to connect a hard disk to your device. To know
how many hard disks could be installed, please refer to the specifications of your device.
Step1: Remove the top cover, and find the hard disk connector and bracket in the device.
Step2: Get a compatible hard disk. With the PCB side facing down, insert the hard disk to one of the hard disk
connector.
Note: To use a green hard disk, use ONLY the hard disk designed especially for surveillance to ensure the
device works properly.
CR2032
CR2032
Hard Disk
Connector
Hard Disk
Bracket
Step3: Fasten the hard disk to the bracket by securing the screw on the bracket.
CR2032
Hard Disk
Step4: Replace the top cover and fasten the screws you loosened in Step1.
4
CONNECTION AND SETUP
 Type 2
Note: Here takes an 8CH model as an example of how to connect a hard disk to your device. To know
how many hard disks could be installed, please refer to the specifications of your device.
Step1: Remove the top cover, and find where to install a hard disk.
Step2: Get a compatible hard disk. With the PCB side facing down, find the screw holes on the DVR base, and place
the hard disk in the DVR.
Note: To use a green hard disk, use ONLY the hard disk designed especially for surveillance to ensure the
device works properly.
Screw hole
CR2032
Screw hole
Hard Disk
Screw hole for
fastening hard disk
Step3: Align the screw holes on the DVR base and the hard disk. Then, fasten the hard disk o the DVR base with the
supplied screws from the bottom side of the DVR.
Step4: Connect the data bus and power cable for the hard disk.
CR2032
Step5: Replace the top cover and fasten the screws you loosened in Step1.
5
CONNECTION AND SETUP
2.2 Camera Connection
Install the camera on the wall or ceiling based on your installation environment and camera type. For installation
details, please refer to the user manual of your camera.
2.2.1 Normal Camera
STEP 1: Connect the coaxial cable to the DVR.
STEP 2: (Optional) Connect the audio cable to the DVR.
STEP 3: Power on the camera and see if the live video shows.
2.2.2 HD CCTV Camera Series
STEP 1: Connect the coaxial cable to the DVR.
STEP 2: Power on the camera and see if the live video shows.
STEP 3: On the DVR side, right click to show the main menu, and go to
OSD MENU to configure the camera if needed.
(ADVANCED CONFIG)  DCCS 
ADVANCED CONFIG
CAMERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
DEVICES
DCCS
IVS
NOTIFY
JOYSTICK
CH1 CH2 CH3 CH4
OSD MENU
DCCS MENU
SETUP
SETUP
F.W.
DEVICE
CONNECTION
1017
AVT Series
OK
EXIT
EZUM Camera Series
If the cameras you connected are our EZUM camera series, we have also designed a series of icons for quick
camera setup. Based on the EZUM camera type connected, you may find some of the icons as listed below for
quick camera configurations, and the sub-functions of each icon may also vary based on the camera connected.
Path: Bottom left on each camera channel view 
.
Day & Night
Configure the day and night modes of the camera
IR Management
Manually adjust the brightness of IR LEDs.
Noise Reduction
Reduce image noise if needed.
Optics
Manually change the shutter speed if needed.
Color
Manually adjust the color-related parameters if needed.
Image Enhancement
Enhance the image performance for better sharpness
and overall identification even in overexposure areas.
Zoom
Used with the motorized lens cameras for optical zoom.
Hot Point
Click on the screen to move the surveillance area to the
point just clicked.
PTZ Control
Open the PTZ control panel to pan, tilt, zoom and cruise
the camera.
Advanced
Set other camera parameters such as camera system,
and mirroring or flipping camera images.
6
CONNECTION AND SETUP
2.2.3 Other brand’s speed dome camera
Note: The recorder must support RS485 connection to connect a speed dome camera. Please check the
specifications of your recorder for details.
STEP 1: Connect the coaxial cable to the DVR.
STEP 2: Find where the connectors of RS485-A and RS485-B are located on the DVR rear panel, and follow the
instructions of your camera manual to connect to the DVR. Then, power on the camera.
STEP 3: On the DVR side, right click to show the main menu, and go to
to set the camera.
(ADVANCED CONFIG)  DEVICES
a) Select the device to PTZ.
b) Set the ID to the value the same as the one set in the camera.
c) Select the protocol to P-P, P-D, S-T or S-E.
Note: P-P and P-D are protocols used Pelco, and S-T and S-E are protocols used by Samsung.
d) Set the baud rate to the value the same as the one set in the camera.
e) Set the interface to RS485.
ADVANCED CONFIG
CAMERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
DEVICES
DCCS
IVS
NOTIFY
JOYSTICK
CH1 CH2 CH3 CH4
DEVICE
ID
PROTOCOL
RATE
INTERFACE

PTZ
000
P-P
2400
RS485



EXIT
2.2.4 IP Camera
Note: Check the specifications of your DVR and see if the DVR supports IP camera connection.
STEP 1: Connect the camera to the same switch / router as the one the DVR is connected, and power on the
camera.
STEP 2: On the DVR side, move the cursor to the left to show the quick bar, and choose
your camera.
(IP Search) to find
IP SEARCH
IP
10.1.1.12
10.1.1.12
PORT
88
88
MAC
00:0e:53:e5:9a:f1
UNKNOWN
TYPE
IP CAMERA
IP CAMERA
PROTOCOL
AVTECH
ONVIF
CONNECT

SETUP
STATUS
UNUSED
UNUSED
EXIT
STEP 3: Select the IP address which is not used and select CONNECT to assign which channel the live video
should be displayed.
7
CONNECTION AND SETUP
2.3 DVR Power On
This device should be operated only with the type of power source indicated on the manufacturer’s label. Connect
the indicated AC power cord to the power adapter, and plug into an electrical outlet.
If your device has a power switch on the rear panel, turn it to “—“. The power LED will be on. If your device doesn’t
have a power switch on its rear panel, the power is on once the power source is connected.
Note: Before the DVR is powered on, make sure (1) the cameras are connected and power-supplied for
the detection of the camera video system to be correct, and (2) a monitor is connected to the DVR
for correct video output detection.
Note: To ensure that your DVR works constantly and properly, it's recommended to use an UPS,
Uninterruptible Power Supply (Optional), for continuously operation.
Note: When your DVR is powered on, please check the chapter of “3. FOR INITIAL USE” in the user
manual to know how to configure this device and change the default user name and password.
To download the user manual, please scan the QR code on the first page, or go to
www.surveillance-download.com/user/z404.swf.
8
FOR INITIAL USE
3. FOR INITIAL USE
For the first time to power on this device, you might be prompted to:

Go through the setup wizard

Clear hard disk

Change default user name and password
3.1 Setup Wizard
The setup wizard is prompted to guide you finishing the most common settings you might need to do.
Note: It’s okay to skip the wizard. You can configure the following settings later in their respective
menus.
SETUP WIZARD
ENGLISH

WELCOME TO THE SETUP WIZARD.
PLEASE FOLLOW THE WIZARD TO FINISH BASIC CONFIGURATIONS.
SKIP
EaZy
NEXT
Choose EaZy (EaZy Networking) to directly go to the EaZy Networking setting page, and refer to “APPENDIX 8
EAZY NETWORKING” at page 82 for details.
Note: To configure network setup by using EaZy Networking later, please go to QUICK START  EaZy.
Or select “NEXT” to go to the next step.
SETUP WIZARD
PLEASE INPUT THIS MACHINE NAME
SKIP
PREV
NEXT
Name the device. If you don’t want to name the device, just skip to the next step.
Note: To name the device later, please go to SYSTEM  SYSTEM INFO.
SETUP WIZARD
USER NAME
PASSWORD
CONFIRM PASSWORD
office_hd
office145
office145
PLEASE INPUT THE ADMINISTRATOR’S USER NAME AND PASSWORD.
SKIP
PREV
NEXT
Change the default user name and password. If you don’t change the user name and password here, you’re not
able to go to the next step. This step is compulsory.
Note: To change or edit user name and passwords, please go to SYSTEM  ACCOUNT.
9
FOR INITIAL USE
SETUP WIZARD
DATE
TIME
FORMAT
GMT
2015/MAR/05
14:33:46
Y/M/D

GMT+08:00 
SKIP
PREV
NEXT
Set the date and time.
If you don’t want to set the date and time now, just skip to the next step. However, it’s necessary to keep the date
and time right to ensure the accuracy of the recorded data.
Note: To set the date and time later, please go to QUICK START  TIME SETUP (“6.1.2 TIME SETUP”
at page 25). When the date and time are changed, you’ll be prompted to clear the hard disk(s).
Select YES to erase the previous recorded data, or there might be data disorder and you wouldn’t
find the footage you need.
SETUP WIZARD
NTP SERVER
SYNC PERIOD
Pool.ntp.org
OFF

SKIP
PREV
NEXT
Configure if you want to connect this device to an NTP server to get the right time online.
Note: To set the date and time later, please go to QUICK START  TIME SETUP (“6.1.2 TIME SETUP”
at page 25).
SETUP WIZARD
NETWORK TYPE
IP
GATEWAY
NETMASK
PRIMARY DNS
SECONDARY DNS
PORT
STATIC

192.168.1.10
192.168.1.1
255.255.255.0
8.8.8.8
168.95.1.1
80
SKIP
PREV
NEXT
Configure network setup by using the traditional method. For details, please download
www.surveillance-download.com/user/network_setup/network_setup_recorder.pdf.
Note: To configure network setup by using the traditional method later, please go to ADVANCED
CONFIG  NETWORK (“NETWORK” at page 39).
SETUP WIZARD
SMTP SERVER
PORT
MAIL FROM
SSL ENCRYPTION
VERIFY PASSWORD
USER NAME
PASSWORD
SKIP
Smtp.gmail.com
465
manager@gmail.com
ON
ON
manager@gmail.com
●●●●●●
PREV
NEXT
Configure event notifications by email.
Note: To configure email notifications later, please go to ADVANCED CONFIG  NETWORK -> EMAIL
(“E-MAIL” at page 39).
10
FOR INITIAL USE
SETUP WIZARD
DDNS
SYSTEM NAME
HOST NAME
E-MAIL
ON
Eagleeyes

MAC000E533A3D
CURRENT HOST ADDRESS
MAC000E533A3D4A.ddns.eagleeyes.tw
SKIP
PREV
NEXT
Enable DDNS if needed.
Note: To enable the DDNS later, please go to ADVANCED CONFIG  NETWORK  DDNS (“NETWORK”
at page 39).
3.2 Clear Hard Disk
When this device is powered on, hard disk detection will be on, and you’ll be prompted to clear the hard disk(s):
CLEAR HDD
CLEAR HDD HDD0
YES
NO
Please choose “YES” to clear the connected hard disk(s), or this device will not detect hard disks properly for
video recording.
It might take some time to clear the connected hard disk(s). When it’s done, you’ll see the remaining hard disk
capacity on the top right corner of the screen.
Note: It’s necessary to clear hard disks in order to format the connected disks to the right format to save
video data. The format used for this device can NOT be read directly on a PC. Please do not install
the hard disk directly to a PC and try to copy the video data saved in the hard disk. The video data
might be impaired.
To change later, right click to show the main menu, and select
(SYSTEM)  SYSTEM INFO  CLEAR
HDD. The DVR will reboot when hard disk data are cleared.
SYSTEM
ACCOUNT
TOOLS
SYSTEM INFO
ONLINE
BACKUP DATA
BACKUP LOG
BAUD RATE
HOST ID
R.E.T.R
AUTO KEY LOCK(S)
CLEAR HDD
RESET DEFAULT
REMOTE CONTROL ID
DEVICE TITLE
2400
000
5
NEVER
HDD-0
SUBMIT
000
OFFICE
SERIAL TYPE
VIDEO FORMAT
VERSION




RS485
NTSC
1019-1008-1010-1010
EXIT
11
FOR INITIAL USE
3.3 Change User Name and Password
It’s highly recommended to change the user name and password of this device to keep your account safe.
Otherwise, any person could access this device if he knows the default user name and password.
If you didn’t go through the setting wizard at the first place, you’ll be prompted to change the user name and
password:
WARNING
PLEASE BE ADVISED TO MODIFY THE
DEFAULT ACCOUNT TO ENSURE YOUR
INFORMATION SECUIRTY.
 MODIFY
O REMIND ME LATER
O DON’T REMIND ME ANYMORE
CONFIRM
Choose MODIFY to start the change immediately.
To change later, right click to show the main menu, and select
default user name and password of SUPERVISOR.
SYSTEM
ACCOUNT
TOOLS
SYSTEM INFO
ONLINE
BACKUP DATA
BACKUP LOG
EXIT
USER LIST
USER NAME
admin
ADD
GROUP
GROUP
SUPERVISOR
EDIT
DEL
12
(SYSTEM)  ACCOUNT to change the
USER INTERFACE
4. USER INTERFACE
4.1 DVR Access
Connect your USB mouse to one of the USB ports on the DVR front panel, and check if there’s a mouse icon (
on the screen, indicating the USB mouse is detected properly.
)
Move your mouse to enter the DVR password with the password keypad. The default user name and password
are both “admin”. The status will be changed from
(key lock) to
(unlock).
Note: You may configure four different user levels to have different access privileges in SYSTEM 
ACCOUNT. For details, please refer to “5.2 User Level Creation” at page 16.
Password Input
4.2 Live Page
4.2.1 DVR Status
Note: Certain icons are for selected models only.
Key lock
Key unlock
Overwrite on
Overwrite off
Internet disconnected
Internet connected
Local connection
USB mouse connected
USB flash drive / device connected
No USB device connected
IVS on
Click to mute an alert buzzer when it sounds
Timer record on
Timer record off
PTZ mode on
PTZ mode off
Sequence mode on
Sequence mode off
Backup event queued and USB flash drive needed
USB flash drive full
13
USER INTERFACE
4.2.2 Channel Status
Note: The functions shown may vary based on the model or the access user level you use.
For Analog Camera
Live audio on
Audio off
Audio playback on
Audio playback off
Recording
PTZ control
Motion event
Alarm event
PIR event
Virtual fence event
One way pass event
Scene Change event
Auto search on
Auto search off
Original size
Fit to screen
Live audio on
Audio off
Audio playback on
Audio playback off
Recording
PTZ control
Alarm event
Motion event
Live information
Playback information
Quick camera control
Camera quick setup
For IP Camera
4.2.3 Record-related Icons
1) Manual Recording
By defaults, manual recording is on ( ) when the DVR is powered on and a hard disk is installed.
2) Event Recording
The event icons,
/
/
/
/
/
, show on the channel status bar when their respective
events occur and the related record function is on.
3) Timer Recording
When timer recording is on, you will see “
” on the screen.
4) HDD Overwritten
Be defaults, the HDD overwritten function is set to ON, and “
” will be shown on the screen.
Note: To disable this function, right click to display the main menu in the live view, and go to “
(ADVANCED CONFIG.)  RECORD  OVERWRITE.
14
”
USER INTERFACE
4.3 Quick Menu Bar
Move to the arrow mark to extend the quick menu bar and show the five functions as follows:
Quick Menu: Open
Click to show the channel switch panel and select the channel you
want.
Click to display the playback control panel, and click
to play the
latest recorded video clip, or click
to enter the search list.
Available only for models which support IP camera connection.
Search for any IP camera(s) connected and assign the camera to a
specific channel. For details, please check “2.2.4 IP Camera” at page 7.
Switch to the channel you want first, and click
to enter the zoom-in
mode. In this mode, click and drag the red frame on the bottom left of
the screen to move to the place you want to see. To exit this mode,
click .
Click to show the power off panel to either halt or reboot the system.
4.4 Main Menu
Right-click anywhere on the screen to show the main menu as follows, and right-click again to exit.
Main Menu
QUICK START
Click to set the status display, image settings,
and date & time.
SYSTEM
Click to set the system configurations.
EVENT INFORMATION
Click to enter the event search menu.
ADVANCED CONFIG
Click to set CAMERA, DETECTION, ALERT,
NETWORK, DISPLAY, RECORD, DEVICES*,
DCCS, IVS*, NOTIFY* and JOYSTICK.
SCHEDULE SETTING
Click to set timer for record, motion detection,
alarm (in and out)*, Push Video*, buzzer, regular
report*, auto backup*, and regular reboot*.
* For selected models only
15
FREQUENTLY-USED FUNCTIONS
5. FREQUENTLY-USED FUNCTIONS
5.1 Key Lock / Unlock
To lock or unlock local operation, click
(lock) or
(unlock) or
(lock) on the DVR status bar to change the status to
(unlock).
To unlock local operation, you’ll be prompted to enter the user name and password to access.
Note: The default user name and password are both admin, which is the highest user level.
Note: Different user level has different access privilege for certain DVR functions. Please refer to “5.2
User Level Creation” at page 16.
5.2 User Level Creation
Note: This function is available only for SUPERVISOR.
To create different user account for different access privilege, click
(SYSTEM), and select ACCOUNT to
enter USER LIST.
SYSTEM
ACCOUNT
TOOLS
SYSTEM INFO
ONLINE
BACKUP DATA
BACKUP LOG
USER LIST
USER NAME
admin
power
normal
guest
EXIT
ADD
GROUP
GROUP
SUPERVISOR
POWER USER
NORMAL
GUEST
EDIT
DEL
Different user group has different access privilege for certain functions as described below:
Note: It’s also available to create a new user group and customizing its access rights. For details, please
refer to “GROUP" at page 27.
Function
User Group
SUPERVISOR
POWER USER
USER
GUEST
Key lock / unlock




/
Live audio on / off



/
Playback audio on / off



/
Full screen / original size display



PTZ Control


Manual alarm out


Camera quick setup


 DVR status
/
 Channel status
16

FREQUENTLY-USED FUNCTIONS
Function
User Group
SUPERVISOR
POWER USER
USER
GUEST
Channel Selection




Playback


IP Search

Digital Zoom




Power

Quick Start

System

Event Information

Advanced Config.

Schedule Setting

REGULAR
REGULAR
REGULAR
REBOOT
REBOOT
REBOOT
 Quick menu bar
 Main menu
 Playback control
/
/
Fast Forward


Fast Rewind


Play / Pause


Stop


Slow Playback


Previous / Next Hour


Quick Search


17
FREQUENTLY-USED FUNCTIONS
5.3 PTZ Control
Note: This function is available only for SUPERVISOR and POWER USER. To know more details, please
refer to “5.2 User Level Creation” at page 16.
Note: For our brand’s HD CCTV motorized camera series, click
focal length and focus adjustment.
might only show specific icons for
For details, please refer to its own user manual.
In the full view
In the split view, click the channel you want to switch to the full screen mode, and click
to show the PTZ
control panel.
/
/
/
+/-
/
/
Enter
Click to confirm your selection / enter the menu.
Up / Down / Left / Right
Click the arrow keys ( /  /  / ) to more the camera lens up /
down / left /right.
Iris + / Iris -
This two buttons are designed for the PTZ camera which uses
Pelco-D to control. To know the actions after clicking Iris + and Iris -,
please refer to the camera’s user manual.
Zoom in / out max
Click to zoom in on the image to the largest / zoom out on the image
to its original size.
Click to zoom in / out on the image.
Users could also zoom in / out on the image by simply drawing a
square on the screen, and the zoom ratio depends on how large the
square is.
Zoom in / out


/
Focus near / far
Zoom in: Draw the square from top left to bottom right.
Zoom out: Draw the square from bottom right to left top.
Click to adjust the focus of the image.
Click to activate the auto function.
Before using it, you need to assign a specific function that will be
Auto mode
is clicked. For details, please refer to the user
enabled when
manual of the camera.
Auto tracking
Click to start auto tracking when your speed dome camera supports
this function.
Preset point
Click to enter the PTZ preset point you want to see.
Camera Menu
Click to enter the camera main menu.
For details about each camera menu, please refer to its own user
manual.
This function is used to memorize the focus parameters you’ve made
after you use
Manual Focus
/
/
/
to manually adjust the focal length
and focus. The next time when you move to the same focal length,
the camera will use the parameters as the ones for Auto Focus.
Auto Focus
Click to automatically adjust the focus of the camera.
Joystick
Click to control the movement of a speed dome camera or a
motorized-pan camera. Drag and hold the mouse on the screen to
move the camera. You’ll see  and
on the screen. The farther
these two icons, the faster the movement.
Config.
Click to configure the speed to pan / tilt the speed dome camera.
18
FREQUENTLY-USED FUNCTIONS
In the split view
Click
on the channel status bar to display the panel as follows:
Up / Down / Left / Right
Click to move your selection up / down / left / right, or
change settings.
/
Digital zoom in / out
Click to zoom in / out the camera image digitally.
/
Focus near / far
Click to adjust the focus of the image.
Preset point
Click to display the preset point panel for preset point
viewing or setting. For details, please refer to the section
below.
/
/
/
How to set a preset point:
Step1:
Step2: Click
click
or
/
to the proper ratio you need, and
/
/
to move to the point you
want to configure as a preset point.
Step3: Click the numbering you want to configure for this
point, and wait till you see
(command sending)
appearing and disappearing on the DVR status bar.
Step4: Repeat from Step1 again to set other points if
needed, or click
to return to the preset point
selection panel.
How to go to a preset point:
Step1:
Step2: Select the numbering within which saves the camera view you want to
see, and wait till you see
(command sending) appearing and
disappearing on the DVR status bar.
5.4 Playback
Note: This function is NOT available for GUEST. Please refer to “5.2 User Level Creation” at page 16.
Click “
” on the quick menu bar to display the playback control panel, and click
video clip, or click
to play the latest recorded
to enter the search list.
Note: There must be at least 8192 images of recorded data for playback to work properly. If not, the
device will stop playback. For example, if the IPS is set to 30, the recording time should be at least
273 seconds (8192 images / 30 IPS) for the playback to work properly.
19
FREQUENTLY-USED FUNCTIONS
5.4.1 Playback Control
Fast Forward
Increase the speed for fast forward. Click once to get 4X speed forward and click
twice to get 8X speed, etc., and the maximum speed is 32X.
Fast Rewind
Increase the speed for fast rewind. Click once to get 4X speed rewind and click
twice to get 8X speed, etc., and the maximum speed is 32X.
Click to play the latest recorded video clip immediately, and click again to pause.
/
Play / Pause
Stop
/
once to get one frame forward, and click
In the pause mode, click
one frame rewind.
Click to stop the video playback.
to get
Slow Playback
Click once to get 1/4X speed playback, and click twice to get 1/8X speed
playback.
Previous /
Next Hour
Click to jump to the next / previous time interval in an hour, for example, 11:00 ~
12:00 or 14:00 ~ 15:00, and start playing the earliest event video clip recorded
during this whole hour.
Repeat
Click to set point A and point B in a video clip, and the system will play only the
specified range in that clip.
Backup
Click to open the backup menu for video backup.
5.4.2 Event Search
Click
to quickly search the recorded files by event types, or select FULL to show all the event logs.
To quickly search the time you want, select QUICK SEARCH.
5.4.3 Audio Playback
In the playback mode, click
or
on the channel status bar to play or mute audio recording.
Note: To make a video backup with audio, or play a recording with audio, make sure the camera which
supports the audio function is connected to the video-in channel and audio-in channel. For
example, the audio data from audio CH1 will be recorded with the video data from video CH1.
For 16CH models, the audio CH1 ~ CH4 are corresponding to video CH1 ~ CH4 respectively.
5.5 Video Backup
Note: This function is available for SUPERVISOR. For details, please refer to “5.2 User Level Creation”
at page 16.
Note: Before using your USB flash drive for video backup, please format it to "FAT32” first with your PC
or laptop. For the list of compatible USB flash drives, please refer to “APPENDIX 4 COMPATIBLE
USB FLASH DRIVE LIST” at page 77.
Note: Video backup could be made via a USB flash drive or the Internet. It’s NOT allowed to connect the
hard disk to your PC / laptop directly for it may impair the recorded data saved in the hard disk.
20
FREQUENTLY-USED FUNCTIONS
To copy video data for video backup, click
(SYSTEM), and select BACKUP DATA.
SYSTEM
ACCOUNT
TOOLS
SYSTEM INFO
ONLINE
BACKUP DATA
BACKUP LOG
START DATE
START TIME
END DATE
END TIME
CHANNEL
2009/NOV/19
08:30:21
2009/NOV/19
17:59:29
3 SELECTED
 ALL
 CH1
 CH2
 CH3
 CH4
 CH5
HARD DISK
OUTPUT FILE FORMAT
TARGET DEVICE
BACKUP
REQUIRE SIZE: 554MB
EXIT
ALL HDD
AVI
USB DEVICE
SUBMIT
SUBMIT




AVAILABLE SIZE: 3788.0MB
Step1: Select the time within which includes the video data you want to backup.
Step2: Select the channel(s) within which includes the video data you want to backup.
Step3: In OUTPUT FILE FORMAT, select the output video format: DEFAULT / AVI.
 When DEFAULT is selected, the footage is saved to ".dv5”, and you can only open it with our own video player
on PC. For details, please check "5.6 Video Playback on PC (.dv5)”.
Note: It’s recommended to save the file to the default format for security reasons. Only specific video
player supports the default format and not everyone can see the video footage.
 When AVI is selected, the footage will be converted to “.avi”, and you can open it with any media player which
supports the “avi” format on PC.
Step4: In TRAGET DEVICE, select USB DEVICE for video backup.
Step5: In REQUIRE SIZE, select SUBMIT to know the file size of the selected footage.
Step6: In BACKUP, select SUBMIT to start copying footage to your USB flash drive, and wait till the backup
successful message appears.
5.6 Video Playback on PC (.dv5)
For video backup with the format “.dv5”, you can only use our own player to play.
Note: It’s NOT allowed to remove the hard disk installed in the DVR and connect it directly to your PC to
check recorded video clips. It might impair the files saved in the hard disk, causing the loss of
those files even when the disk is replaced back to the DVR.
To play “.dv5” video on your PC:
Step1: Insert the USB flash drive with recorded data into your PC.
Note: The supported PC operating systems are Windows 10, Windows 8, Windows 7, Windows Vista &
Windows XP.
Step2: Find the program “PLAYER.EXE” in the USB flash drive, and double-click it to install.
Note: “PLAYER.EXE” can also be downloaded from www.surveillance-download.com/user/z404.swf.
Step3: Run the program, VideoPlayer, and browse to where you save the recorded data.
Step4: Select the file you want to start video playback.
21
FREQUENTLY-USED FUNCTIONS
5.6.1 Convert the file format to AVI
To convert the video file format to AVI, click AVI from the playback panel to start file conversion.
Note: The recorded audio (if any) will be removed when the file format is converted to AVI.
Note: If the footage includes data for multiple channels, click to a specific channel for this function to
work properly.
5.7 Digital Zoom
Switch to the channel you want to zoom in, and move to the left side of the screen to show the quick start bar.
Click
to enter the zoom-in mode. In this mode, click and drag the red frame on the bottom left of the screen to
move to the place you want to see.
To exit this mode, right-click anywhere on the screen.
Note: You need to exit the zoom mode first to use other DVR functions.
22
MAIN MENU
6. MAIN MENU
6.1 QUICK START
6.1.1 GENERAL
QUICK START
GENERAL
TIME SETUP
DAYLIGHT
EaZy
CHANNEL TITLE
EVENT STATUS
DATE DISPLAY
DCCS DISPLAY
ON
ON
ON
ON
MOUSE SENSITIVITY
0
AUDIO GAIN
0
RECORD CONFIG
SETUP
5
5
10
15
EXIT
1)
CHANNEL TITLE
Select to display the channel title or not (ON / OFF).
2)
EVENT STATUS
Select to display the event icons or not (ON / OFF).
Note: For details about each event icon, please refer to “4.2 Live Page” at page 13.
3)
DATE DISPLAY
Select to display the date or not (ON / OFF).
4)
DCCS DISPLAY
Select to display the OSD or not (ON / OFF) when users are using specific camera functions.
Note: This function is available only when the connected HD CCTV camera is the same brand as this
recorder.
5)
MOUSE SENSITIVITY
Select the mouse sensitivity. The higher the value, the more sensitive the mouse.
6)
AUDIO GAIN
Select the level to enhance the audio signals. The higher the value, the stronger the signals.
23
MAIN MENU
7)
RECORD CONFIG
Click SETUP to enter the setting page individually for manual record, event record and timer record.
a) Select the record type you want to set.
b) In CHANNEL, select ALL to apply the changes here to all channels.
Note: The I.P.S. section is based on NTSC system.
MANUAL RECORD
CHANNEL
ALL
EVENT RECORD
IMAGE SIZE
FHD(1080P)
QUICK START
TIMER RECORD
I.P.S.
240
QUALITY
SUPER BEST
BITRATE (kbps)
2064
EXIT
Or, select BY CHANNEL to set the image size, image per second & image quality individually for each
channel.
Note: The available options for IMAGE SIZE depend on the recorder you have.
Note: Some models support up to 5MP (2592 x 1944) video recording for IP cameras. However, when
the image size is set to 3MP (2048 x 1536) or more, the local live display and playback will be set
to sub stream display (D1 by default). To check the recording at 3MP or more resolution, please
copy and play it on a PC / laptop.
IMAGE SIZE
The pixels of the image, for example, FHD(1080P) = 1920 x 1080.
The more the pixels, the clearer the image but the more the file size.
I.P.S.
Image per second. The more the I.P.S., the more fluent the video but the more the
file size.
QUALITY
Image quality.
BITRATE
It is used to set the upper limit of the transmission number per second. The value
could be configured from 256 up to 8192 depending on the DVR model you have.
The value set here is related to the image size. For example, here are the
recommended values:
 FHD(1080P) => 2048
 HD(720P) => 1024
The more the value, the bigger the file size, but the system stability might go down.
The less the value, the smaller the file size, but the image quality might go down.
24
MAIN MENU
6.1.2 TIME SETUP
QUICK START
GENERAL
TIME SETUP
DAYLIGHT
EaZy
DATE
TIME
NTP SERVER
FORMAT
SYNC PERIOD
GMT
2009 / NOV / 17
15 : 35 : 53
tock.stdtime.gov.tw
Y/M/D
DAILY
(GMT+08:00)TAIPEI
EXIT
1)
DATE
Set the current date. The default display format is YEAR – MONTH – DATE (Y-M-D).
2)
TIME
Set the current time in HOUR : MIN : SEC.
3)
NTP SERVER
Click to change the default NTP server to another server they’re familiar with, or keep the default NTP
server.
Note: This function works only when this device is configured to the Internet.
4)
FORMAT
Select one date format from the following three options: Y/M/D, M/D/Y or D/M/Y.
5)
SYNC PERIOD
Select to synchronize the time every day (DAILY), or turn this function off (OFF).
6)
GMT
Select your time zone.
6.1.3 DAYLIGHT
QUICK START
GENERAL
TIME SETUP
DAYLIGHT
EaZy
DAYLIGHT SAVING
ON
START TIME
1ST
MON
AUG
06:00
END TIME
LAST
OCT
10:00
MON
ADJUST
01:00
EXIT
Depending on the time zone you’re in:
1)
DAYLIGHT SAVING
Select to enable (ON) or disable (OFF) this function.
2)
START TIME / END TIME
Set the start time and end time.
3)
ADJUST
Set the time in HOUR : MIN.
25
MAIN MENU
6.1.4 EaZy
EaZy Networking is a cloud service to connect your devices to the Internet automatically through our free mobile
app, EagleEyes, in a few steps without going through the complicated network setup including port forwarding.
For details, please refer to “APPENDIX 8 EAZY NETWORKING” at page 82.
QUICK START
GENERAL
TIME SETUP
DAYLIGHT
EaZy
ENABLE EAZY NETWORKING
ON
EXIT
6.2 SYSTEM
6.2.1 ACCOUNT
USER LIST
This function is used to create a new user account, or modify or delete an existing account for different access
privilege.
Note: For details about available local operations of each user level, please refer to “5.2 User Level
Creation” at page 16.
SYSTEM
ACCOUNT
TOOLS
SYSTEM INFO
BACKUP DATA
BACKUP LOG
USER LIST
USER NAME
admin
power
user
guest
EXIT
ADD
GROUP
GROUP
SUPERVISOR
POWER USER
NORMAL
GUEST
EDIT
DEL
 How to create an account
Select ADD, enter a user name and its password, and assign a user group in which includes the access rights
you wish to grand to this new account. Then, select SAVE to create and return to the user list page.
ADD
USER NAME
PASSWORD
CONFIRM PASSWORD
GROUP
TEST1


GUEST
SAVE

CANCEL
26
MAIN MENU
GROUP
This function is used to create a new group with customized user access rights for different functions if needed,
and you can create a user account and assign it to your customized group.
Note: The default user groups are SUPERVISOR, POWER USER, USER and GUEST, and they’re not
allowed to be removed. For details about available local operations of each user group, please
refer to “5.2 User Level Creation” at page 16.
SYSTEM
ACCOUNT
TOOLS
SYSTEM INFO
ONLINE
BACKUP DATA
BACKUP LOG
USER LIST
GROUP
 ━
SUPERVISOR
POWER USER
USER
GUEST
GENERAL
LIVE PLAYBACK NETWORK LIVE STREAM
BACKUP
PTZ CONTROL
POWER CONTROL
REVIEW LOG
CONFIG SETUP
CLEAR LOG
ACCOUNT SETUP
CLEAR HDD
PUSH VIDEO
PUSH STATUS
ALARM OUT
NETWORK PLAYBACK STREAM
ALL
ENABLE
ENABLE
ENABLE
ENABLE
DISABLE
DISABLE
DISABLE
DISABLE
DISABLE
ENABLE

EXIT
 How to create a group and customize access rights
Step1: Enter a name in the column next to , and select  to create a group. You’ll find it added in the group list.
Step2: Select the group you just added in the group list, and select the tabs of GENERAL, LIVE, PLAYBACK,
NETWORK LIVE STREAM and NETWORK PLAYBACK STREAM to choose the corresponding
functions you want to enable or disable.
Step3: Return to USER LIST, and create an account or modify an existing account to assign it to the group you
just added.
6.2.2 TOOLS
SYSTEM
ACCOUNT
TOOLS
SYSTEM INFO
ONLINE
BACKUP DATA
BACKUP LOG
LANGUAGE
UPGRADE
NETWORK UPGRADE
BACKUP CONFIG
RESTORE CONFIG
UPGRADE CAMERA PARAMETERS
UPGRADE CAMERA FIRMWARE
ENABLE AUTO PLUG AND PLAY
BIND MAC ADDRESS
ENGLISH
SUBMIT
SUBMIT
SUBMIT
SUBMIT
UPGRADE
UPGRADE
ON
ON

EXIT
1)
LANGUAGE
Select the language of the OSD.
2)
UPGRADE
Save the upgrade files obtained from your installer or distributor in a compatible USB flash drive, and insert it
into the USB port at the front panel. Then, click SUBMIT to start upgrading.
Note: Before using the USB flash drive, please use your PC to format the USB flash drive to FAT32 format
first. For the list of compatible USB flash drives, please refer to “APPENDIX 5 COMPATIBLE USB
FLASH DRIVE LIST” at page 77.
Note: After upgrading firmware, it’s recommended to clear all HDD data for the system to work more
stably. Before clearing all HDD data, please remember to make video backup.
27
MAIN MENU
3)
NETWORK UPGRADE
Click SUBMIT for perform system upgrade via Internet.
Note: This function requires Internet access. Please make sure this recorder is connected to Internet
before using this function.
4)
BACKUP CONFIG / RESTORE CONFIG
To save the DVR current configurations for later use, such as restoring after DVR upgrade or applying to
another DVR, insert a compatible USB flash drive into the USB port, and select SUBMIT in BACKUP
CONFIG to copy the current DVR configurations to a file “System.bin” and save to your USB flash drive.
To restore the DVR configurations, insert the USB flash drive including “System.bin” to the USB port, and
select SUBMIT in RESTORE CONFIG.
5)
UPGRADE CAMERA PARAMETERS / UPGRADE CAMERA FIRMWARE
This function is used only to upgrade the parameters / firmware of our brand’s HD CCTV camera when
necessary.
Get the upgrade file from our installer or distributor and save it to a USB flash drive. Then, select
UPGRADE to start the upgrade.
6)
ENABLE AUTO PLUG AND PLAY
Switch to ON allow the camera to be detected and configured automatically when it’s connected to this
device.
Note: This function is available only when the brand of the cameras connected is the same as this
device.
7)
BIND MAC ADDRESS
This function is recommended to be used when your surveillance system is more than 256 cameras. It would
be helpful for the system to get the address of each connected camera quickly if the system accidentally
shuts down and needs to recover.
6.2.3 SYSTEM INFO
SYSTEM
ACCOUNT
TOOLS
SYSTEM INFO
ONLINE
BACKUP DATA
BACKUP LOG
BAUD RATE
HOST ID
R.E.T.R
AUTO KEY LOCK(S)
CLEAR HDD
RESET DEFAULT
REMOTE CONTROL ID
DEVICE TITLE
VIDEO FORMAT
SERIAL TYPE
2400
000
5
NEVER
HDD-0
SUBMIT
000
office
AUTO




RS485
VIDEO FORMAT
NTSC
VERSION
1001-1000-1000-1001
EXIT
1)
BAUD RATE
Set the baud rate of the DVR (2400 / 4800 / 9600 / 19200 / 38400 / 57600 / 115200).
Note: This function is used when an external controller is connected to this DVR and further
configurations should be made for this DVR to work with the controller. For details, please check
the user manual of the external controller.
28
MAIN MENU
2)
HOST ID
Set the ID of the DVR (000 ~ 254).
Note: This function is used when an external controller is connected to this DVR and further
configurations should be made for this DVR to work with the controller. For details, please check
the user manual of the external controller.
3)
R.E.T.R (Remote Event Trigger Recording)
Select the timeout in minute after which the R.E.T.R. function will be activated (3 / 5 / 10 / 30).
4)
AUTO KEY LOCK(S)
Set the time-out in second after which the key lock function is activated (NEVER / 30 / 60 / 120).
5)
CLEAR HDD
Select the HDD you want to clear, and click YES to confirm or NO to cancel.
It’s recommended to clear all data in the hard disk when:
 It’s the first time to use this DVR to ensure the recorded data are not mixed with other data previously saved in the
same hard disk.
 The DVR firmware is upgraded for the system to work more stably. Before clearing all HDD data, please remember
to make video backup.
 DVR date and time are changed accidentally when the recording function is activated. Otherwise, the recorded
data will be disordered and you will not be able to find the recorded file to backup by time search.
6)
RESET DEFAULT
Click “SUBMIT” to reset all settings as default, and select YES to confirm or NO to cancel. The DVR will
reboot after reset.
7)
REMOTE CONTROL ID
This function is available when users need to control two or more DVRs with one IR remote controller. The
ID set here is used to identify the DVR the remote controller is going to control. Please also read the user
manual of the IR remote controller for details.
8)
DEVICE TITLE
Enter a title for this device.
9)
VIDEO FORMAT
Allow the DVR to detect the video format automatically (AUTO), or choose NTSC or PAL manually.
10) SERIAL TYPE
Here shows the serial type of the DVR (RS-485).
11) VIDEO FORMAT
Here shows the information of the DVR video format (NTSC / PAL).
12) VERSION
Here shows the firmware version information.
29
MAIN MENU
6.2.4 ONLINE
Insert a compatible USB flash drive to the USB port at the front panel.
Note: Before using your USB flash drive for video backup, please format it to "FAT32” first with your PC
or laptop. For the list of compatible USB flash drives, please refer to “APPENDIX 4 COMPATIBLE
USB FLASH DRIVE LIST” at page 77.
SYSTEM
ACCOUNT
TOOLS
SYSTEM INFO
ONLINE
BACKUP DATA
BACKUP LOG
ANONYMOUS VIEWER LOGIN
DROP ALL VIDEO CONNECTION
LOGIN FAILURE NUMBER
LOCK TIME OF LOGIN FAILURES
OFF
SUBMIT
3
1 MIN


EXIT
1)
ANONYMOUS VIEWER LOGIN
Switch to ON to allow anonymous login, meaning there’s no need to enter user name and password for
remote access.
2)
DROP ALL VIDEO CONNECTION
Click SUBMIT to force disconnection of all remote logins when needed.
3)
LOGIN FAILURE TIMES
Select how many times of remote login failures (1 ~ 20) to enable device lock automatically for security
reasons.
4)
LOCK TIME FOR LOGIN FAILURES
Select the device lock time (1 MIN / 2 MINS / 3 MINS / 5 MINS / 10 MINS / 30 MINS / 1 HOUR) when
remote login failures reach to the number specified in LOGIN FAILUTRE TIME(S). You’ll be unable to
see the login page of this device until the specified time is up.
6.2.5 BACKUP DATA
Note: It’s NOT allowed to remove the hard disk installed in the DVR and connect it directly to your PC to
check video footage. It might impair the files saved in the hard disk, causing the loss of those files
even when the disk is replaced back to the DVR.
Note: This function is available only when a hard disk is installed.
Insert a compatible USB flash drive to the USB port at the front panel.
Note: Before using your USB flash drive for video backup, please format it to "FAT32” first with your PC
or laptop. For the list of compatible USB flash drives, please refer to “APPENDIX 4 COMPATIBLE
USB FLASH DRIVE LIST” at page 77.
30
MAIN MENU
SYSTEM
ACCOUNT
TOOLS
SYSTEM INFO
ONLINE
BACKUP DATA
BACKUP LOG
EXIT
1)
START DATE
START TIME
END DATE
END TIME
CHANNEL
HARD DISK
OUTPUT FILE FORMAT
TARGET DEVICE
BACKUP
REQUIRE SIZE: 554MB
2009/NOV/19
08:30:21
2009/NOV/19
17:59:29
ALL
ALL HDD
DEFAULT
USB DEVICE
SUBMIT
SUBMIT


AVAILABLE SIZE: 3788.0MB
START DATE / START TIME
Select the start date & time.
2)
END DATE / TIME
Select the end date & time.
3)
CHANNEL
Click to select the channel(s).
4)
HARD DISK
Select the hard disk containing the video data you need or ALL HDD.
5)
OUTPUT FILE FORMAT
Select the file format for backup video: DEFAULT or AVI.
 When DEFAULT is selected, the copied video is saved to ".dv5”, and you can only open it with our own video
player on PC. For details, please check the next section, "Video Playback on PC (.dv5)”.
Note: It’s recommended to save the file to the default format for security reasons. Only specific video
player supports the default format and not everyone can see the video footage.
 When AVI is selected, the copied footage will be converted to “.avi”, and you can open it with any media player
which supports the “.avi” format on PC.
6)
TARGET DEVICE
Select the device you want to use for video backup: USB DEVICE.
7)
BACKUP
Click SUBMIT to start backup.
8)
REQUIRE SIZE
To know the size of the expected backup video before backup, click SUBMIT to start calculating.
Video Playback on PC (.dv5)
For video backup with the format “.dv5”, you can only use our own player to play.
Note: It’s NOT allowed to remove the hard disk installed in the DVR and connect it directly to your PC to
check recorded video clips. It might impair the files saved in the hard disk, causing the loss of
those files even when the disk is replaced back to the DVR.
To play “.dv5” video on your PC:
Step1: Insert the USB flash drive with recorded data into your PC.
Note: The supported PC operating systems are Windows 10, Windows 8, Windows 7, Windows Vista &
Windows XP.
31
MAIN MENU
Step2: Find the program “PLAYER.EXE” in the USB flash drive, and double-click it to install.
Note: “PLAYER.EXE” can also be downloaded from www.surveillance-download.com/user/z404.swf.
Step3: Run the program, VideoPlayer, and browse to where you save the recorded data.
Step4: Select the file you want to start video playback.
Convert the file format to AVI:
To convert the video file format to AVI, click AVI from the playback panel to start file conversion.
Note: The recorded audio (if any) will be removed when the file format is converted to AVI.
Note: If the footage includes data for multiple channels, click to a specific channel for this function to
work properly.
6.2.6 BACKUP LOG
This function is used to export event logs for quick checking or backup. A .csv file will be exported to your USB
flash drive. You can open it with a text editor to see the logs.
Note: This function is available only when a hard disk is installed.
Insert a compatible USB flash drive to the USB port at the front panel.
Note: Before using the USB flash drive, please use your PC to format the USB flash drive to FAT32 format
first. For the list of compatible USB flash drives, please refer to “APPENDIX 4 COMPATIBLE USB
FLASH DRIVE LIST” at page 77.
SYSTEM
ACCOUNT
TOOLS
SYSTEM INFO
ONLINE
BACKUP DATA
BACKUP LOG
START DATE
START TIME
END DATE
END TIME
CHANNEL
DATA TYPE
2009/NOV/19
08:30:21
2009/NOV/19
17:59:29
ALL
3 SELECTED
 ALL
 MANUAL
 MOTION
 ALARM
 SYSTEM
 TIMER
SUBMIT
BACKUP
EXIT
1)
START DATE / START TIME
Select the start date & time.
2)
END DATE / TIME
Select the end date & time.
3)
CHANNEL
Click to select the channel(s).
32




MAIN MENU
4)
DATA TYPE
Click “SETUP” to select the event type you want: MANUAL / MOTION / ALARM / SYSTEM / TIMER /
HUMAN DETECTION / INFLOW / OUTFLOW / VIRTUAL FENCE / ONEWAY / SENCE CHANGE,
or select ALL to choose all event types.
Note: The event types available depend on the model you have.
5)
BACKUP
Click SUBMIT to start backup. You’ll see a log file (.csv) in the flash drive. You may open it with any txt
editor, such as NotePad.
6.3 EVENT INFORMATION
6.3.1 QUICK SEARCH
EVENT INFORMATION
QUICK SEARCH
EVENT SEARCH
HDD INFO
EVENT LOG
CHANNEL
SUN
1
8
15
22
29
00

2 SELECTED
2009
MON
2
9
16
23
30
06
NOV
TUE
3
10
17
24
WED
4
11
18
25
THU
5
12
19
26
12
FRI
6
13
20
27
18
15 : 20
EXIT
SAT
7
14
21
28
24
SUBMIT
Step1: Select the channel including the video data you want to search.
Step2: Select the year and month including the video data you want to search from the calendar, and the date with
recorded data will be highlighted.
Note: To select the year and month, move your mouse to the display bar. Then, click and hold to drag up
or down.
Step3: Select the date you want from the calendar, and the time with recorded data will be highlighted from the
time scale bar.
Step4: To immediately play the video clip, click SUBMIT.
To choose the start time for video playback, move your mouse cursor to the highlighted time, and click to
confirm the time when the time display below is the time you want. The video playback is activated right
away when you confirm the time.
Note: For video playback operations, please refer to “5.4 Playback” at page 19.
6.3.2 EVENT SEARCH
EVENT INFORMATION
QUICK SEARCH
EVENT SEARCH
HDD INFO
EVENT LOG
DATE
TIME
CHANNEL
HARD DISK
EVENT TYPE
SEARCH
2009/NOV/19
16:13:16
1

ALL HDD

MOTION
START

EXIT
33
MAIN MENU
1)
DATE / TIME
Select the specific time period that you want to search.
2)
CHANNEL
Select the video channel you want to search.
3)
HARD DISK
Select the hard disk including the video data you want to search, or select ALL HDD.
4)
EVENT TYPE
Select the event type you want to search (MOTION / ALARM / HUMAN DETECTION / INFLOW /
OUTFLOW / VIRTUAL FENCE / ONEWAY / SCENE CHANGE), or select ALL to choose all events.
Note: Some events are available only for selected models.
5)
SEARCH
Click START to start search and play the video data immediately.
6.3.3 HDD INFO
You can check the remaining capacity of the connected hard disk in this device and its current status.
If the healthy status goes to:
 GOOD - This hard disk works normal.
 BELOW AVERAGE - The hard disk might work with some errors. Please pay attention and do video backup if needed.
 REPLACEMENT NEEDED – Please replace this hard disk immediately to ensure continuous video recording.
EVENT INFORMATION
QUICK SEARCH
EVENT SEARCH
ID
TYPE
STATUS
SIZE
TEMP.
HDD-0 NORMAL READY 890.562GB 46°C
SERIAL NUMBER
ST31000526SV
FREE SIZE
864.832GB
FORMAT TIME HEALTHY STATUS
2011/DEC/13
GOOD
18:18:53
HDD INFO
EVENT LOG
EXIT
6.3.4 EVENT LOG
You can check all system events (SYSTEM) and backup logs (BACKUP), or clear all log records.
EVENT INFORMATION
QUICK SEARCH
EVENT SEARCH
HDD INFO
EVENT LOG
SYSTEM
EVENT
KEY UNLOCK
BACKUP
TIME
COMMENT
2009/NOV/19 15:49:07
VIDEO LOSS
2009/NOV/19 15:32:05
POWER ON
2009/NOV/19 15:32:02
PREV
NEXT
04
CLEAN
EXIT
34
MAIN MENU
6.4 ADVANCED CONFIG
6.4.1 CAMERA
ADVANCED CONFIG
CAMERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
DEVICES
DCCS
IVS
NOTIFY
JOYSTICK
CH1 CH2 CH3 CH4
INTERFACE
CAMERA TYPE (Appears only when INTERFACE is COAXIAL)
BRIGHTNESS
CONTRAST
SATURATION
HUE
REC
TIME STAMP DISPLAY
CHANNEL TITLE
REC AUDIO
ALARM OUT DURATION (SECS) (For selected models only)
CONNECTION (Appears only when INTERFACE is IPCAM)
COAXIAL
AUTO
128
128
128
128
ON
ON
CH1
ON
3
SETUP


EXIT
1)
INTERFACE
Here shows how the camera is connected to this device: COAXIAL or IPCAM.
Usually this function will be detected automatically unless you want to change the camera type from an IP
camera to an analog camera.
If an IP camera was previously connected and now you want to replace it with an analog camera, please
manually change IPCAM to COAXIAL for the camera detection to work properly.
2)
CAMERA TYPE (Appears only when INTERFACE is COAXIAL)
When INTERFACE is COAXIAL, you’ll see CAMEA TYPE and the options are AUTO (default) / TVI /
ANALOG HD.
3)
BRIGHTNESS / CONTRAST / SATURATION / HUE (Appears only when INTERFACE is COAXIAL)
Click the current value to manually adjust the brightness/contrast/saturation/hue of each channel here.
4)
REC
Select if you want to enable recording for the selected channel (ON / OFF).
Note: When this function is disabled, no manual, event or timer recording will be activated even if any
of these three record functions is set to ON.
5)
TIME STAMP DISPLAY
Enable this function and the recording time will be shown on the video during video playback.
6)
CHANNEL TITLE
Click the channel title column to change the channel title (up to 12 characters). The default title is the
channel number.
7)
REC AUDIO
Enable or disable audio recording for the selected channel if the connected camera supports audio
recording.
8)
ALARM OUT DURATION (SECS) (For selected models only)
Select the duration time in second when an alarm-out event occurs (3 / 5 / 10 / 20 / 30).
35
MAIN MENU
9)
CONNECTION (Appears only when INTERFACE is IPCAM)
When INTERFACE is IPCAM, you’ll see CONNECTION to further configure the IP camera.
CONNECTION – CH1
VENDOR
MODEL
STREAM PROTOCOL
METHOD
URI
PORT
SUB STREAM PATH
RECORD STREAM PATH
USER NAME
PASSWORD
CACHE TIME (MSEC)
ONVIF
RTP-Unicast
HTTP
182.168.1.10
88
test
test
6.4.2 DETECTION
ADVANCED CONFIG
CAMERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
DEVICES
DCCS
IVS
NOTIFY
JOYSTICK
CH1 CH2 CH3 CH4
LS
SS
TS
MOTION
ALARM
AREA
PRIVACY MASK
INTERNAL ALARM (For selected models only)
GUARD LOCK
07
03
02
OFF
OFF
EDIT
EDIT
ON
SETUP
EXIT
1)
LS (Level of Sensitivity)
LS is to set the sensitivity of comparing two different images. The smaller the value is, the higher sensitivity
for motion detection. The highest sensitivity setting is 00, and the lowest sensitivity setting is 15. The default
value is 07.
2)
SS (Spatial Sensitivity)
SS is to set the sensitivity for detecting the size of one object (the number of the grids) on the screen. The
smaller the value is, the higher sensitivity for motion detection.
The highest sensitivity setting is 00, and the lowest sensitivity setting is 15. The default setting is 03.
Note: The default setting of SS is 03, which means once an object is detected more than 3 grids, the
system will get triggered. So the value of SS must be less than the number of grids that you set
up for the motion detection area.
3)
TS (Time of Sensitivity)
TS is to set the sensitivity regarding how long one object stays in the detection area and triggers the
recording. The smaller the value is, the higher sensitivity for motion detection.
The highest sensitivity setting is 00, and the lowest sensitivity setting is 15. The default setting is 02.
4)
MOTION
Select if you want to activate the motion detection function for the selected channel (ON / OFF).
5)
ALARM
Select N.C. / N.O. depending on your installation need. The default alarm value is OFF.
36
MAIN MENU
6)
AREA
Click EDIT to set the motion detection area.
There are 16 × 12 grids per camera for all channels. Pink blocks represent the area that is not being
detected while the transparent blocks are the area under detection.
7)
PRIVACY MASK
You can cover certain areas on the camera image with privacy masks.
Note: Up to 4 areas could be added.
NAME
1
2
2
2
FUNCTION
OFF
ON
OFF
OFF
PRIVACY MASK
MOSAIC COLOR
TRANSPARENCY
0%
25%
0%
0%
EDIT
Select one existing profile, and choose EDIT to modify it.

EDIT
PRIVACY MASK - EDIT
FUNCTION
MOSAIC COLOR
TRANSPARENCY
MASK AREA
ON
50%
SETUP
APPLY
8)
Item
Description
MOSAIC SIZE
Choose the mosaic size of the privacy mask. The options are: 8×8, 32×32, and 64×64.
MOSAIC COLOR
Select the color for the privacy mask.
TRANSPARENCY
Select the transparency for your privacy mask. The options are: 0%, 25%, 50%, and 100%.
MASK AREA
Select “SETUP” to enter the area selection page. To exit, right click on the mouse.
INTERNAL ALARM (For selected models only)
This function is available only when an HD CCTV camera with a PIR sensor built-in is connected to this
device. You could enable or disable the PIR detection here.
Note: To know which camera could work with this function, please check with your installer or
distributor.
9)
CAMERA GUARD
This function is available only for the camera which supports motorized-pan. It will temporarily disable the
pan function of the camera and move the camera angle to a preset area for surveillance when Guard is
enabled on the mobile app, EagleEyes, remotely.
To use this function, you need to at least have one preset point and preset group configured on your camera,
and have the mobile app, EagleEyes, installed on your mobile device.
Note: To know how to configure preset points and preset groups, please refer to the user manual of your
camera. To know where to download the app, EagleEyes, please refer to “7.2 Mobile Devices” at
page 62.
37
MAIN MENU
CAMERA GUARD – CH1
GUARD LOCK
TIMEOUT (SECS)
PRESET GROUP
PRESET NUMBER
ON
30
1
3



APPLY
Enable GUARD LOCK, choose the preset group and point you want to monitor, and configure the timeout
after which the camera will be fixed to the selected point. Any attempt to pan the camera to another point will
be failed when GUARD on the mobile app, EagleEyes, is enabled.
6.4.3 ALERT
ADVANCED CONFIG
CAMERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
DEVICES
DCCS
IVS
NOTIFY
JOYSTICK
EXT. ALERT
INT. BUZZER
KEY BUZZER
VLOSS BUZZER
MOTION BUZZER
ALARM BUZZER
HDD BUZZER
ALARM DURATION (SEC)
HDD NEARLY FULL (GB)
HDD OVERHEAT ALERT (°C)
HDD FAILURE BUZZER
ON
OFF
ON
ON
ON
ON
ON
5
5
60
ON



EXIT
1)
EXT. ALERT
Select to enable or disable the sound when any external alarm is triggered (ON / OFF).
2)
INT. BUZZER
Select to enable or disable the sound (ON / OFF) for all internal buzzers: KEY BUZZER, VLOSS
BUZZER, MOTION BUZZER, ALARM BUZZER, and HDD BUZZER.
Note: When this item is set to OFF, item 3) to item 7) will be disabled even though they are set to ON.
3)
KEY BUZZER
Select to enable or disable the sound when pressing the buttons on the front panel (ON / OFF).
4)
VLOSS BUZZER
Select to enable or disable the sound when video loss happened (ON / OFF).
5)
MOTION BUZZER
Select to enable or disable the sound when any motion alarm is triggered (ON / OFF).
6)
ALARM BUZZER
Select to enable or disable the sound when any internal alarm is triggered (ON / OFF).
7)
HDD BUZZER
Select to enable or disable the sound (ON / OFF) when the HDD remaining capacity reaches to the value set
in HDD NEARLY FULL (GB).
8)
ALARM DURATION (SEC)
Select the duration time for alarm buzzer in second (5 / 10 / 20 / 40).
9)
HDD NEARLY FULL (GB)
If HDD BUZZER is enabled, select the duration time for buzzer notifications when the hard disk available
capacity is 5/10/15/20 GB left.
38
MAIN MENU
10) HDD OVERHEAT ALERT (°C)
Select the temperature alert for your hard disk to be aware of the possible overheat of your hard disk.
11) HDD FAILURE ALERT
Select to enable or disable the sound when any of the installed hard disk(s) fails to work normally (ON /
OFF).
6.4.4 NETWORK
NETWORK
 WAN is used to connect this recorder to Internet for remote access from anywhere as long as Internet access is
available.
 DDNS is used when the Internet access is available.
Note: For more details about these two functions and network configurations, please get the setup
manual from
www.surveillance-download.com/user/network_setup/network_setup_recorder.pdf.
ADVANCED CONFIG
CAMERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
DEVICES
DCCS
IVS
NOTIFY
JOYSTICK
WAN E-MAIL DDNS PROTOCOL EaZy
NETWORK TYPE
IP
GATEWAY
NETMASK
PRIMARY DNS
SECONDARY DNS
PORT
CHECK INTERNET AVAILABILITY BY ADDRESS
ENABLE UPNP
EXIT
STATIC 
192.168.001.010
192.168.001.254
255.255.255.000
8.8.8.8
168.95.1.1
80
www.google.com
OFF
MAC: 00:0E:53:EC:A7:B4
E-MAIL
When this function is enabled and an event occurs, a html file including a link will be sent to the specified E-mail
address. Click the link to access to this DVR and check the event recording.
ADVANCED CONFIG
CAMERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
DEVICES
DCCS
IVS
NOTIFY
JOYSTICK
WAN
E-MAIL
DDNS
SMTP SERVER
PORT
MAIL FROM
SSL ENCRYPTION
VERIFY PASSWORD
USER NAME
PASSWORD
PROTOCOL
EaZy
Smtp.gmail.com
465
manager@gmail.com
ON
ON
manager@gmail.com
●●●●●●
EXIT
1)
SMTP SERVER
Enter the SMTP server address provided from your e-mail system supplier.
2)
PORT
Enter the port number provided from your e-mail system supplier. If this column is left blank, the e-mail
server will use port 25 to send e-mails.
3)
MAIL FROM
Enter the email address which will be used to send Email notifications.
39
MAIN MENU
4)
SSL ENCRYPTION
Select ON if your e-mail server is using SSL encryption to protect your e-mail content from unauthorized
access.
5)
VERIFY PASSWORD
Some mail servers are required to verify the password. Please enter the “user name” and “password”.
6)
USER NAME / PASSWORD
Enter the “user name” and “password” to access the email address entered in MAIL FROM when VERIFY
PASSWORD is set to ON.
PROTOCOL
ADVANCED CONFIG
CAMERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
DEVICES
DCCS
IVS
NOTIFY
JOYSTICK
WAN E-MAIL DDNS PROTOCOL EaZy
TCP PAYLOAD LENGTH
8192
UDP PAYLOAD LENGTH
1200
EXIT
1)
TCP PAYLOAD LENGTH / UDP PAYLOAD LENGTH
Configure the payload length from 100 ~ 10000.
The higher the value, the larger data packet is carried, and the longer time is needed for the video to display.
The lower the value, the less data packet is carried, and the more possibility you might see video lag.
EaZy
This function is used to connect this recorder to Internet by using EaZy Networking. For details, please refer to
“APPENDIX 9 EAZY NETWORKING” at page 82.
ADVANCED CONFIG
CAMERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
DEVICES
DCCS
IVS
NOTIFY
JOYSTICK
WAN E-MAIL DDNS PROTOCOL EaZy
ENABLE EAZY NETWORKING ON
EXIT
40
MAIN MENU
6.4.5 DISPLAY
ADVANCED CONFIG
CAMERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
DEVICES
DCCS
IVS
NOTIFY
JOYSTICK
FULL SCREEN DURATION
QUAD SCREEN DURATION (For selected models only)
HDD DISPLAY MODE
HDMI RESOLUTION
VGA RESOLUTION (For selected models only)
SPOT MONITOR
03

03

REMAINING SIZE
AUTO
1920 X 1024
SETUP



EXIT
1)
FULL SCREEN DURATION
Select the full screen dwell duration time in second (03 / 05 / 10 / 15).
2)
QUAD SCREEN DURATION (For selected models only)
Select the quad screen dwell duration time in second (03 / 05 / 10 / 15).
3)
HDD DISPLAY MODE
Select REMAINING SIZE to show the remaining HDD capacity for recording, REMAINING TIME to
show the remaining recording time, or DAYS KEPT to show how many recording data are saved in day.
4)
HDMI RESOLUTION
Select the display resolution you want. The default value is AUTO. This is used for the main display output.
Note: To have the best image quality on your monitor, make sure (1) the selected DVR output resolution
is supported by your monitor, and (2) the output settings on both the LCD monitor and DVR are
consistent.
If the image is not positioned or scaled properly, please go to your monitor’s menu for adjustment.
For details, please refer to the user manual of your monitor.
5)
VGA RESOLUTION (For selected models only)
Select the display resolution you want. The options are 1920 x 1080 / 1280 x 720 / 1024 x 768.
Note: To have the best image quality on your monitor, make sure (1) the selected DVR output resolution
is supported by your monitor, and (2) the output settings on both the LCD monitor and DVR are
consistent.
If the image is not positioned or scaled properly, please go to your monitor’s menu for adjustment.
For details, please refer to the user manual of your monitor.
6)
SPOT MONITOR
Specify how VGA / composite port is used for video output: CALL MONITOR / EVENT MONITOR /
LIVE / MAIN MONITOR.
Note: For some models, only the composite port supports this function. The available output options are
depending on the model you have.
 CALL MONITOR is used for sequence display. When this option is selected, go to “CALL SCREEN
DURATION” to select the duration time in second (03 / 05 / 10 / 15) and “CALL MONITOR
PERMIT” to choose the channel(s) you want for sequence display.
SPOT MONITOR
SPOT MONITOR (For selected models only)
SPOT DISPLAY
CALL SCREEN DURATION
CALL MONITOR PERMIT
VGA
CALL MONITOR
5
4 selected
41




MAIN MENU
 EVENT MONITOR is used when any alarm event occurs. When this option is selected, go to
“LAYOUT” to select how many channels you want to see, and “PRE-ALARM (SEC)” and
“POST-ALARM (SEC)” to set how many seconds you’d like to see before (0 ~ 5) and after (3 ~ 10)
the event starts.
SPOT MONITOR
SPOT DISPLAY
LAYOUT
PRE-ALARM (SEC)
POST-ALARM (SEC)
EVENT MONITOR
4
3
5




 LIVE is used to select how many channels you’d like to show on the spot monitor.
SPOT MONITOR
SPOT DISPLAY
LAYOUT
CH1
CH5


LIVE
4


CH3
CH8


 MAIN MONITOR is used for normal video display.
6.4.6 RECORD
Note: Please DO NOT change the date or time of your DVR after the recording function is activated.
Otherwise, the recorded data will be disordered and you will not be able to find the recorded file
to backup by time search. If users change the date or time accidentally when the recording
function is activated, it’s recommended to clear all HDD data, and start recording again.
ADVANCED CONFIG
CAMERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
DEVICES
DCCS
IVS
NOTIFY
JOYSTICK
MANUAL RECORD
EVENT RECORD
TIMER RECORD
PRE-ALARM RECORD
OVERWRITE
KEEP DATA LIMIT (DAYS)
RECORD CONFIG
SUBSTREAM RESOLUTION
ON
ON
ON
ON
ON
OFF
SETUP
CIF
EXIT
1)
MANUAL RECORD
Set the manual recording function on / off.
42


MAIN MENU
2)
EVENT RECORD
Set the event recording function on / off.
3)
TIMER RECORD
Set the timer recording function on / off.
4)
PRE-ALARM RECORD
Select to enable or disable the pre-alarm function (ON / OFF).
When pre-alarm and event recording functions are both activated, the DVR will record 8MB data before an
alarm / motion event is triggered.
5)
OVERWRITE
Select ON to overwrite previous recorded data in your hard disk when the hard disk is full. When this
function is on and the hard disk is full, the DVR will clear 8GB data from the oldest for continuous recording
without notice.
6)
KEEP DATA LIMITS (DAYS)
Assign the maximum recording days from 1 to 31 after which all the recorded data will be removed, or select
7)
OFF to disable this function.
RECORD CONFIG
Click SETUP to enter the setting page individually for manual record, event record and timer record.
For details, please refer to “6.1.1 GENERAL” at page 23.
8)
SUBSTREAM RESOLUTION
Select the resolution for sub-streams: FRAME / CIF.
Sub-streams are used for remote surveillance from a PC or mobile device. When the bandwidth is low,
choose a lower resolution helps to quickly view the video, but the video quality might get low.
6.4.7 DEVICES
Note: This function is used when the DVR supports RS485 connection, and you want to connect other
brand’s speed dome camera.
ADVANCED CONFIG
CAMERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
DEVICES
DCCS
IVS
NOTIFY
JOYSTICK
CH1 CH2 CH3 CH4
DEVICE
ID
PROTOCOL
RATE
INTERFACE
PTZ
00
NORMAL
2400
RS485




EXIT
1)
DEVICE
For connecting other brand’s speed dome camera, select PTZ.
2)
ID
Click the current value to set the ID number (0 ~ 255) for the connected camera if necessary.
Make sure the ID setting of the camera is the same as the setting here, or the DVR will not be able to control
the device.
Note: To know the default ID of the speed dome camera, please refer to its user manual.
43
MAIN MENU
3)
PROTOCOL
Select NORMAL (our protocol), P-D (PELCO-D), P-P (PELCO-P), S-T (SAMSUNG-T) or S-E
(SAMSUNG-E) protocol.
4)
RATE
Select the baud rate for the connected speed dome camera (2400 / 4800 / 9600 / 19200 / 38400 /
57600 / 115200).
Make sure the baud rate setting of the camera is the same as the setting here, or the DVR will not be able to
control the device.
Note: To know the default baud rate of the speed dome camera, please refer to its user manual.
5)
INTERFACE
Select RS485 if the connected speed dome camera uses RS485 wires to transmit control signals.
6.4.8 DCCS
This function is used for our brand’s HD CCTV camera series. Users could access the setup menu of the camera
itself for further configurations.
ADVANCED CONFIG
CAMERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
DEVICES
DCCS
IVS
NOTIFY
JOYSTICK
CH1 CH2 CH3 CH4
OSD MENU
DCCS MENU
SETUP
SETUP
F.W.
1031
DEVICE
AVT series
CONNECTION
OK
EXIT
1)
OSD MENU
When the connected camera is properly recognized, click SETUP to enter the setup page of the camera
itself.
2)
DCCS MENU
This menu appears when the camera is properly recognized, and it is used to enter the additional function
setup page designed for the connected camera.
Note: Functions additionally designed are not available for every HD CCTV camera. Please check the
camera user manual for details.
6.4.9 IVS
Note: This function is for selected models only.
Note: Before using the IVS function, make sure the event record function is enabled on your DVR.
IVS, Intelligent Video Surveillance, is the advanced application for motion detection, but more precise and smarter.
It can be applied to different situations with one of the following three modes: FLOW COUNTING, VIRTUAL
FENCE, and ONE WAY.
When anyone crosses the detection line (virtual fence), the recording will be on.
Note: Four camera channels are supported for this function.
44
MAIN MENU
ADVANCED CONFIG
CAMERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
DEVICES
DCCS
IVS
NOTIFY
JOYSTICK
IVS1 IVS2 IVS3 IVS4
CAMERA
IVS MODE
DISPLAY LINE
SENSITIVITY
RESET COUNT
VIRTUAL FENCE AREA
SCENE CHANGE
SCENE CHANGE LEVEL
CH3
FLOW COUNTING
OFF
7
SUBMIT
SETUP
OFF
MIDDLE





EXIT
1)
CAMERA
Select the camera channel that you want to use the IVS function.
2)
IVS MODE
Select one of the following three modes depending on your environment:
3)
MODE
DESCRIPTION
FLOW COUNTING
A virtual detection line is set to detect the moving direction of pedestrians for flow counting.
VIRTUAL FENCE
A virtual detection line is set to detect intruders crossing the detection line, and an alarm will be
triggered.
ONE WAY
A virtual detection line is set to detect intruders from the specified direction, and an alarm will be
triggered.
DISPLAY LINE
Select to display the detection line for IVS on the screen or not.
4)
SENSITIVITY
Set the sensitivity for IVS from 00 ~ 15. The larger the value, the more sensitive the IVS will be.
5)
RESET COUNT
Click SUBMIT to reset the flow counting number to 0 when the IVS mode is set to FLOW COUNTING
and activated.
6)
VIRTUAL FENCE AREA
Click SETUP to draw the detection line for IVS, and set the detection direction from left to right, or right to
left. This area setting is the detection base for IVS MODE.
Note: There are some tips to draw the detection line. For details, please check
www.surveillance-download.com/user/IVS_setup.pdf.
7)
SCENE CHANGE
Select ON to trigger a motion event when the camera is sensed to be moved and the camera scene is
changed. At the same time, the icon “
“
8)
” will be also shown on the screen in addition to the motion icon
”.
SCENE CHANGE LEVEL
Set the detection sensitivity for SCENE CHANGE to HIGH, MIDDLE or LOW.
45
MAIN MENU
IVS APPLICATION
 FLOW COUNTING
Step1: Go to VIRTUAL FENCE AREA to draw a detection line with your mouse, and decide the
detection direction by selecting REVERSE.
Step2: Click APPLY to finish the IVS setting and return to the live view. The IVS icon “
on the status bar. Click it to show the flow counting on the top left side.
” will be shown
When anyone walks across the detection line, the system will determine his movement is in or out,
and add one count to the corresponding channel on the flow counting panel.
IN
People coming from the opposite direction to the arrow mark.
OUT
People coming from the same direction as the arrow mark.
46
MAIN MENU
 VIRTUAL FENCE and ONE WAY
Step1: Go to VIRTUAL FENCE AREA to draw a detection line with your mouse, and decide the
detection direction by selecting REVERSE.
Step2: Click APPLY to finish the IVS setting and return to the live view.
When anyone walks across the detection line, the system will determine his movement is in or out,
and:
VIRTUAL FENCE
An event happens for anyone walking across the detection line, and “
will be shown on the screen.
ONE WAY
An event happens for anyone walking from the opposite direction to the
arrow mark, and “
47
” will be shown on the screen.
”
MAIN MENU
IVS STATISTICS
Click “
”“
” to enter the event search menu. Then, select STATISTIC
LIST
QUICK SEARCH
RECORD
MOTION
ALARM
TIME
SYSTEM
HUMAN DETECTION
IVS
FULL
STATISTIC
CHANNEL
EVENT TYPE
TIME
STATISTIC
3 SELECTED
 ALL
 CH1
 CH2
 CH3
 CH4
 CH5




3 SELECTED
 ALL

 INFLOW
 OUTFLOW
 VIRTUAL FENCE
 ONEWAY

 MOTION
2010/MAY/17
SUBMIT
EXIT
Set all the criteria you want to search, and click SUBMIT in STATISTIC to show the event statistics by
DAY in LIST (default) or CHART.

To check the statistics in the bar chart, click CHART.

To switch to the MONTH or HOUR view, click DAY at the bottom.
List View
IVS STATISTIC
LIST
CHART

HOUR
COUNT
00:00 – 00:59
0
01:00 – 01:59
0
02:00 – 02:59
0
03:00 – 03:59
0
04:00 – 04:59
0
05:00 – 05:59
10
06:00 – 06:59
0
07:00 – 07:59
0
08:00 – 08:59
5
09:00 – 09:59
0
2010/MAY/17

BACKUP
48
DAY
EXIT
MAIN MENU
Chart View
IVS STATISTIC
LIST
CHART

30
COUNT
24
18
12
6
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
0
HOUR
2010/MAY/17

BACKUP
DAY
EXIT
6.4.10 NOTIFY
You can configure this DVR to send notifications for certain events to mobile devices with our mobile app,
EagleEyes, installed, or to the specified E-mail address(es) or FTP site.
PUSH VIDEO
Note: This function is for selected models only.
Before using this function, make sure:





An external alarm is connected to the alarm-in port on the rear panel.
You have an iOS or Android mobile phone or tablet.
You have subscribed the mobile network service from your mobile service provider.
The mobile app, EagleEyes, is installed in your mobile device. For details, please refer to “7.2 Mobile Devices” at page 62.
You have configured EagleEyes to access this DVR, and Guard is enabled. For details, please refer to “APPENDIX 3 SET PUSH
VIDEO” at page 74.
You’ll get an active event notification with video telling you the occurrence of alarm event(s).
ADVANCED CONFIG
CANERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
DEVICES
DCCS
IVS
NOTIFY
JOYSTICK
PUSH VIDEO
PUSH STATUS
MESSAGE MAIL
MAIL
RESET ALL GUARD CONNECTION
SUBMIT
GUARD TRIGGER BY
ALARM IN 1
CH01
ALARM OFF / INTERNAL ALARM
CH02
ALARM OFF
CH03
ALARM N.O.
CH04
ALARM OFF
FTP





CH1
CH2
office
CH4
EXIT
1)
RESET ALL GUARD CONNECTION
When there’re more than 2 users who have the authority to enable Push Video on their mobile devices and
configure its related settings, it might be confusing to know whose command is working. In this case, use this
function could force the camera to discard all Push Video setup and reconfigure it.
49
MAIN MENU
2)
GUARD TRIGGER BY
Specify which alarm device (alarm-in) should be used when GUARD is enabled from your iOS or Android
mobile device.
3)
ALARM TYPE
Select the external alarm type to ALARM NO., ALARM N.C. and INTERNAL ALARM.
4)
CH01 ~ 04
Enter the text you want to see when your iOS or Android mobile device receives Push Video. The default
text is the channel number.
PUSH STATUS
Before using this function, make sure:




You have an iOS or Android mobile phone or tablet.
You have subscribed the mobile network service from your mobile service provider.
The mobile app, EagleEyes, is installed in your mobile device. For details, please refer to “7.2 Mobile Devices” at page 62.
You have configured EagleEyes to access this DVR, and Guard is enabled. For details, please refer to “APPENDIX 3 SET PUSH
VIDEO” at page 74.
You’ll get a text message telling you the occurrence of selected system event(s).
ADVANCED CONFIG
CANERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
DEVICES
DCCS
IVS
NOTIFY
JOYSTICK
PUSH VIDEO
PUSH STATUS
MESSAGE MAIL
MAIL
FTP
ACTION
ON
EVENT

ALL

VIDEO LOSS

HDD FULL

POWER ON

HDD (CLEAR / NO HDD / OVER TEMPERATURE)

NET LOGIN

KEY UNLOCK

UPS

SYSTEM ABNORMAL
EXIT
Step1: Switch ACTION to ON.
Step2: Select the system event(s) you want to get notified via your mobile device.
Step3: Enable GUARD in EagleEyes on your mobile device, and try to trigger a system event to see if you’ll get
Push Status.
50
MAIN MENU
MESSAGE MAIL
Note: For E-mail notifications, make sure you have configured an E-mail account in NETWORK 
E-MAIL to send the notifications.
Enable this function in ACTION, select the event type(s) you want to send notifications in EVENT, and add the
E-mail address(es) to which you want to send notifications in RECEIVER.
You’ll get an E-mail telling you the occurrence of your selected event(s).
ADVANCED CONFIG
CANERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
DEVICES
DCCS
IVS
NOTIFY
JOYSTICK
PUSH VIDEO
PUSH STATUS
MESSAGE MAIL
MAIL
FTP
ACTION
ON
EVENT

ALL

VIDEO LOSS

HDD FULL

POWER ON

HDD (CLEAR / NO HDD / OVER TEMPERATURE)

NET LOGIN

KEY UNLOCK

NETWORK

UPS

SYSTEM ABNORMAL
RECEIVER
SETUP
EXIT
MAIL
Note: For E-mail notifications, make sure you have configured an E-mail account in NETWORK 
E-MAIL to send the notifications.
ADVANCED CONFIG
CANERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
DEVICES
DCCS
IVS
NOTIFY
JOYSTICK
PUSH VIDEO
PUSH STATUS
MESSAGE MAIL
MAIL
FTP
E-MAIL BY EVENT
ON
E-MAIL BY GUARD
ON
RECEIVER
SETUP
CONTENT TYPE
AVI

EXIT
1)
E-MAIL BY EVENT
Select to receive email notifications when any event occurs.
2)
E-MAIL BY GUARD
Select to receive email notifications only when Push Video and Push Status events occur.
3)
RECEIVER
Click “Setup” to enter the email address(es) of the person(s) to receive email notifications.
4)
CONTENT TYPE
Select which type of notifications you want to receive: LINK, AVI or JPEG.
 For LINK, you’ll receive an html file. For details, please refer to the next section “How to check video footage by
LINK”.
 For AVI, you’ll receive a file of video footage in the “AVI” format.
 For JPEG, you’ll receive a snapshot in the “JPEG” format.
51
MAIN MENU
How to check video footage by “LINK”
Step1: Open the html file received.
Note: Please accept and install ActiveX control on your computer. It’s recommended to use Internet
Explorer to open the HTML file.
Step2: Enter the user name and password to log into this DVR, and select the channel you want.
Step3: Click Open to download the footage to your computer and play.
Note: The footage download and playback will be failed if either of your DVR and PC is not connected to
Internet.
FTP
ADVANCED CONFIG
CANERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
DEVICES
DCCS
IVS
NOTIFY
JOYSTICK
PUSH VIDEO
PUSH STATUS
MESSAGE MAIL
MAIL
FTP
UPLOAD BY EVENT
ON
UPLOAD BY GUARD
ON
USER NAME
office
PASSWORD

SERVER
211.75.33.2144
PORT
25
DIRECTORY
video
CONTENT TYPE
AVI
EXIT
1)
UPLOAD BY EVENT
Select to get event notifications uploaded when any event occurs.
52

MAIN MENU
2)
UPLOAD BY GUARD
Select to get event notifications uploaded only when Push Video and Push Status events occur.
3)
USER NAME / PASSWORD / SERVER / PORT / DIRECTORY
Enter the information needed for FTP uploading.
4)
CONTENT TYPE
Select which type of notifications you want to receive: LINK, AVI or JPEG.
 For LINK, you’ll receive an html file. For details, please refer to the next section “How to check video footage by
LINK”.
 For AVI, you’ll receive a file of video footage in the “AVI” format.
 For JPEG, you’ll receive a snapshot in the “JPEG” format.
How to check video footage by “LINK”
Step1: Open the html file received.
Note: Please accept and install ActiveX control on your computer. It’s recommended to use Internet
Explorer to open the HTML file.
Step2: Enter the user name and password to log into this DVR, and select the channel you want.
Step3: Click “Open” to download the footage to your computer and play.
Note: The footage download and playback will be failed if either of your DVR and PC is not connected to
Internet.
53
MAIN MENU
6.4.11 JOYSTICK
In this menu, you can adjust the speed of pan / tilt movement of the speed dome camera or a motorized-pan
camera.
Note: To control the movement of the speed dome camera, you can choose
from the PTZ control
panel and move on the screen (“5.3 PTZ Control” at page 18), or simply connect the compatible
joystick, AVX102, to the DVR.
ADVANCED CONFIG
CONNECTION
MAX SPEED OF X AXIS
100
CAMERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
NOTIFY
MULTICASTING
JOYSTICK
MAX SPEED OF Y AXIS
CURVE ORDER OF X AXIS
CURVE ORDER OF Y AXIS
100
1
1
EXIT
6.5 SCHEDULE SETTING
6.5.1 RECORD / DETECTION / ALARM IN / ALARM OUT / PUSH VIDEO / BUZZER
Select the timer type you want to configure (RECORD / DETECTION / ALARM IN / ALARM OUT / PUSH
VIDEO / BUZZER), choose ON to enable the timer, and select the day and time for this function.
Note: Push Video is available for selected models only.
Note: The selected time bar is marked as blue.
SCHEDULE SETTING
RECORD
DETECTION
ALARM IN
ALARM OUT
PUSH VIDEO
BUZZER
REGULAR REPORT
AUTO BACKUP
REGULAR REBOOT
RECORD TIMER
0
2
ON
4
6
8
SUN
MON
TUE
WED
THU
FRI
SAT
EXIT
X axis
Y axis
0 ~ 24 hours. Each time bar is 30 minutes.
Monday ~ Sunday.
54
10
12
14
16
18
20
22
24
MAIN MENU
6.5.2 REGULAR REPORT
This function is used to send event reports to the specified E-mail address. Users could configure up to 5 profiles
to receive different reports about specific channels at different time.
Note: This function is for selected models only.
Note: This function is available only when a hard disk is installed, and the DVR is connected to Internet.
SCHEDULE SETTING
RECORD
DETECTION
ALARM IN
ALARM OUT
PUSH VIDEO
BUZZER
REGULAR REPORT
AUTO BACKUP
REGULAR REBOOT
PROFILE
ACTIVE
EXECUTION PERIOD
EXECUTION DAY OF MONTH
EXECUTION HOUR
CHANNEL
EVENT TYPE
E-MAIL
1
ON
MONTHLY
1
1
CH1
MOTION
SETUP





EXIT
Step1: Select the profile you want to configure, and enable it.
Step2: Select the frequency to send reports in PERIOD: DAILY / MONTHLY / WEEKLY.
Step3: When MONTHLY or WEEKLY is selected, select which date or day from EXECUTION DAY OF
MONTH or EXECUTION DAY OF WEEK.
Step4: Then, select which time you want to receive reports, which channel(s) you want to see, and which event
type(s) you want to see (MANUAL / MOTION / ALARM / SYSTEM / TIMER / HUMAN
DETECTION / INFLOW / OUTFLOW / VIRTUAL FENCE / ONEWAY / SCENE CHANGE).
Step5: Configure the email address to receive reports.
Note: The sender E-mail should be configured in ADVANCED CONFIG  NETWORK  E-MAIL for this
function to work properly. For details, please refer to “E-MAIL” at page 39.
6.5.3 AUTO BACKUP
This function is used to schedule video backup regularly, uploading security footages to a FTP site (remotely) or
saving to an USB device connected to the DVR (locally).
Note: This function is for selected models only.
You can configure up to 7 profiles and use one of them as your backup preference.
SCHEDULE SETTING
RECORD
DETECTION
ALARM IN
ALARM OUT
PUSH VIDEO
BUZZER
REGULAR REPORT
AUTO BACKUP
REGULAR REBOOT
PROFILE
ACTIVE
FTP USER NAME
FTP PASSWORD
FTP PORT
FTP SERVER
FTP DIRECTORY
METHOD
VIDEO
AUDIO
VIDEO SOURCE
EXECUTION PERIOD
EXECUTION DAY OF WEEK
EXECUTION HOUR
BACKUP START DAY OF WEEK
BACKUP START TIME
BACKUP END DAY OF WEEK
BACKUP END TIME
EXIT
55
1
ON
Office

25
211.75.33.2144
Video
FTP
ALL
2 SELECTED
RECORD STREAM
WEEKLY
MON
23
MON
23:00
MON
23:00










MAIN MENU
1)
PROFILE
Select the profile you want to configure.
2)
ACTIVE
Switch to ON to enable the selected profile.
3)
FTP USER NAME / FTP PASSWORD / FTP PORT / FTP SERVER / FTP DIRECTORY
Enter all the information needed to access the FTP site you want if you want to upload those footages to an
FTP site.
4)
METHOD
Choose where you to save those footages: FTP / USB DEVICE.
5)
VIDEO / AUDIO
Select the video / audio channels you want to backup.
6)
VIDEO SOURCE
Choose RECORD STREAM or SUB STREAM:
 RECORD STREAM: The video quality is good, but it also consumes much storage.
 SUB STREAM: It consumes less storage, but the video quality might be not satisfactory.
7)
EXECUTION PERIOD
Select how often you want to backup footages: WEEKLY or DAILY.
8)
EXECUTION DAY OF WEEK
This option is available only when WEEKLY is chosen. Select one day from MON ~ SUN.
For example, if you want to backup video data from Monday, 01:00am to Friday, 23:59pm on every Saturday,
09:00am, choose SAT here.
9)
EXECUTION HOUR
Select an exact hour to start rebooting from 0 ~ 23.
For example, if you want to backup video data from Monday, 01:00am to Friday, 23:59pm on every Saturday,
09:00am, choose 9 here.
10)
BACKUP START DAY OF WEEK
This option is available only when WEEKLY is chosen. Select one day from MON ~ SUN.
For example, if you want to backup video data from Monday, 01:00am to Friday, 23:59pm on every Saturday,
choose MON here.
11)
BACKUP START TIME
Enter the start time for backup.
For example, if you want to backup video data from Monday, 01:00am to Friday, 23:59pm on every Saturday,
enter 01:00 here.
12)
BACKUP END DAY OF WEEK
This option is available only when WEEKLY is chosen. Select one day from MON ~ SUN.
For example, if you want to backup video data from Monday, 01:00am to Friday, 23:59pm on every Saturday,
choose FRI here.
13)
BACKUP END TIME
Enter the end time for backup.
For example, if you want to backup video data from Monday, 01:00am to Friday, 23:59pm on every Saturday,
enter 23:59 here.
56
MAIN MENU
6.5.4 REGULAR REBOOT
This function is used to schedule this device to reboot regularly to free some unused cache data and make the
system more reliable.
Note: This function is for selected models only.
SCHEDULE SETTING
RECORD
DETECTION
ALARM IN
ALARM OUT
PUSH VIDEO
BUZZER
REGULAR REPORT
AUTO BACKUP
REGULAR REBOOT
ACTIVE
EXECUTION PERIOD
EXECUTION DAY OF MONTH
EXECUTION HOUR
ON
MONTHLY
1
1



EXIT
2)
ACTIVE
Switch to ON to enable this function.
3)
EXECUTION PERIOD
Select how often you want to reboot the system: MONTHLY, WEEKLY or DAILY.
4)
EXECUTION DAY OF MONTH / EXECUTION DAY OF WEEK
Depending on the option you selected in EXECUTION PERIOD:
 EXECUTION DAY OF MONTH shows when MONTHLY is selected. Select one day from 1 ~ 31 to reboot.
 EXECUTION DAY OF WEEK shows when WEEKLY is selected. Select one day from Monday ~ Sunday to
reboot.
5)
EXECUTION HOUR
Select an exact hour to start rebooting from 0 ~ 23.
57
REMOTE OPERATION
7. REMOTE OPERATION
7.1 Web Browser
You can view the images or operate your DVR with a web browser, for example, Microsoft Internet Explorer.
Note: The supported PC operating systems are Windows 10, Windows 8, Windows 7, Windows Vista &
Windows XP, and it’s recommended to run Internet Explorer as administrator (Run as
administrator).
Note: To use Mozilla Firefox or Google Chrome for remote access, please go to Apple’s official website
(http://www.apple.com) to download and install QuickTime first.
Note: The illustration below is just for your reference and may be different from what you actually see.
Some functions and buttons are for selected models or certain user levels only.
Step 1: Key in the IP address used by this device in the URL address box, such as 60.121.46.236, and press
Enter. You will be prompted to enter the user name and password to access the device.
If the port number this device used is NOT 80, you need to key in the port number additionally. The
format is ipaddress:portnum.
For example, for the IP address 60.121.46.236 and port No. 888, please key
in ”http://60.121.46.236:888” into the URL address box, and press Enter.
Step 2: Enter the user name and password, and click OK. You will see a similar screen as the following when the
login information is correct.
Note: The default user name and password for remote access are both admin.
Icon
Description
Click to go to the live view of the DVR.
Click to go to the detailed DVR setting.
Click to enter the PTZ mode. This function is also used for our band’s HD CCTV motorized camera
series to adjust its focal length and focus remotely. For details, please refer to “7.1.2 PTZ Panel” at
page 61.
Video / Audio Control
Format
H.264 / QuickTime
QuickTime is Apple Inc.’s multimedia software. You need to have QuickTime installed in you
operation system first. When “QuickTime” is selected, you will be promoted to enter the user name
and password to access the server of the DVR.
Quality
BEST / HIGH / NORMAL / BASIC
Select the image quality.
Sub Stream
Resolution
FRAME / CIF
Select the sub stream resolution (FRAME: 704*480 / CIF: 352*240) for live display.
58
REMOTE OPERATION
Icon
Description
Audio
Select the audio channel you want for listening to the live audio.
Note: Your camera must support audio recording, and connect to the video channel
which supports audio recording and the audio input of the DVR. For details,
please refer to “1.3 Rear Panel” at page 2.
means mute.
To disable the mute status, click this icon again and select the audio channel you want.
Priority*
Quality / Frame rate
This function is used to choose the live display priority between Quality and Frame rate.
When “Quality” is chosen, the video quality goes up but the display will get lagged.
When “Frame rate” is chosen, the display is fluent but the video quality will go down.
Streaming
This function shows only when a single channel is selected. Choose the stream resolution for live
display.
When Sub Steam is selected, the resolution will be the one selected in Sub Stream
Resolution; When Recording is selected, the resolution will be the one selected in “
“DVR” -> “Record”. -> “Manual”.
Cache Time
” ->
Select the cache time from 0 ~ 800ms.
The higher the value, the more time it’s going to be needed to wait for the image to show, but the
better the image quality will be.
Channel Control
Channel Selection
(1 ~ 16 / 1 ~ 8 / 1 ~ 4)
Click one of the numbers to switch to the channel you want to see in full screen.
Click to go to the previous / next channel, or change setting.
/
Click to take a snapshot of the current view, and save it to the specified path in your PC set in “
”
 “General”.
/
/
/
:
Click to display each channel one by one, starting from CH1. When the last channel is
displayed, it will start from CH1 again.
:
To exit from this display mode, press any other channel display button.
Click to show 4-cut / 9-cut / 16-cut display.
Click to enable local desktop display remotely. An individual window will pop up to show the local
view. All operations available at the local side could be done independently and remotely in this
window.
Click to switch the display to full screen.
Event Search & Playback
Increase the speed for fast rewind. Click once to get 4X speed rewind and click twice to get 8X
speed, etc., and the maximum speed is 32X.
Increase the speed for fast forward. Click once to get 4X speed forward and click twice to get 8X
speed, etc., and the maximum speed is 32X.
Click to play the current video clip.
Click to pause the video playback.
Click to stop the video playback.
Click to play the video clip slowly, once to get 4X slower, twice get 8X slower.
Click to enter the record list and search and footage you need.
Click to enter the backup menu and copy the footage you need to your PC.
Note: To play the backup file (.avc), go to
player to install.
-> General -> Configure, and download the
Alarm Out*
Channel Selection
(1 ~ 8 / 1 ~ 4)
Click one of the channel numbers to command the camera to trigger the alarm-out device you want.
IVS Panel*
This button is enabled only when the IVS mode is enabled. Click to show the detection line.
Click to enter the IVS statistics page. For details, please refer to “7.1.1 IVS Statistics” at page 60.
* For selected models only
59
REMOTE OPERATION
7.1.1 IVS Statistics
Note: This function is for selected models only.
60
REMOTE OPERATION
7.1.2 PTZ Panel
Note: This function is for selected models only.
Function
Description
Click to enter the camera main menu. For details about each camera menu, please refer to its own
user manual.
///
Click the arrow keys ( /  /  / ) to more the camera lens up / down / left /right.
PTZ Channel
Select the channel which connects the PTZ camera or our brand’s HD CCTV motorized camera you
want to control.
Preset
Click on the preset point numbering to which you want your camera to move.
/
Click to adjust the focus of the image.
/
Click to zoom in / out the image.
/
Click to zoom in on the image to the largest / zoom out on the image to its original size.
Click to start auto tracking when your speed dome camera supports this function.
Click to take a snapshot of the current view, and save it to the specified path in your PC set in
 General.
Click to activate the auto function. Before using it, you need to assign a specific function that will be
enabled when “
” is clicked. For details, please refer to the user manual of your PTZ camera or
our brand’s HD CCTV motorized camera.
61
REMOTE OPERATION
7.2 Mobile Devices
Note: For more details about mobile surveillance via your mobile device, download the instructions of
EagleEyes installation and configuration from
www.surveillance-download.com/user/eagleeyes_quick.pdf.
EagleEyes is a mobile phone program used with our surveillance system for remote surveillance. It has several
advantages:
 It’s free (Except EagleEyes Plus for iPhone, EagleEyes Plus+ for Android, and EagleEyesHD Plus for iPad).
 It’s compatible with several popular mobile platforms, such as iOS and Android.
7.2.1 Prerequisites
Before installing EagleEyes to your mobile device for remote surveillance, make sure you have checked the
following:

Your mobile platform is iOS or Android.

Mobile Internet services are subscribed and available to use for your mobile device.
Note: You might be charged for Internet access via the wireless or 3G network. For the Internet access
rate details, please check with your local network operator or service provider.

You have noted down the IP address, port number, user name and password used to access your network
camera from Internet.
7.2.2 Where to download


For iOS users, please go to “App Store”, and search “EagleEyes” to download.
For Android users, please go to “Play Store”, and search “EagleEyes” to download.
When the download is completed, EagleEyes will be installed automatically to the location where all applications
are saved in your phone by default, or where you specify.
7.2.3 Manual Setup
Note: To know how to configure by EaZy Networking, please refer to “APPENDIX 8 EAZY NETWORKING”
at page 82.
Step1: Open EagleEyes to go to the address book.
Step2: Then, click +, and select Manual to go to the setting page.
62
REMOTE OPERATION
Step3: In the setting page, enter all the information needed to access this device in the REQUIRED column,
and click Get Type to examine if the information you entered is correct. The device type will be detected
properly.
Step4: (Optional) Configure the settings in the OPTIONAL column as needed.
Step5: Click Save to return to the address book. Enable Guard to receive Push Video / Push Status.
Note: Push Video / Push Status is for selected models only. Before enabling Guard, please make sure if
your device supports this function.
Step6: Click on the item you just added in the address book to access and check the live view.
63
APPENDIX 1 SPECIFICATIONS
APPENDIX 1 SPECIFICATIONS

4CH Models
Model 1
Model 2
Model 3
 Video
Video System
NTSC / PAL (auto detection)
Video Compression Format
H.264
Video Signal
IP / TVI / Analog HD / 960H
Analog HD / TVI / 960H
Video Input
4 quadbrid channels
4 tribrid channels
Video Input Interface
Analog Mode
IP Mode
Video Output
Video Resolution
Composite video signal 1 Vp-p 75Ω BNC
Ethernet, 10/100 Base-T
NO
BNC
YES
VGA
YES
HDMI
YES
Analog Mode
IP Mode
1080P / 720P / QHD / 960H / Frame / Field / CIF
Live & Playback:
1920 x 1080 / 1280 x 720 /
640 x 480 / 320 x 240
Record**:
2592 x 1944 / 2048 x 1536 /
1920 x 1080 /
1280 x 720/ 640 x 480 /
320 x 240
NO
 Record & Backup
Max. Recording Rate
Up to 120 IPS @ 1920 x 1080
Recording Mode
Up to 60 IPS @ 1920 x 1080
Manual / Timer / Motion / Alarm / Remote
Pre-alarm Recording
YES
Playback Channel
4CH
Quick Search
Time / Motion / Alarm search mode
Backup Device
USB 2.0 flash drive / Network
Regular Backup
YES
 Audio
Audio Input
1 audio input
Audio Output
1 audio output (Mono)
 General
Hard Disk Storage
6TB SATA HDD x 2
SATA Interface
eSATA Interface
(For external disk array connection)
YES
YES
Image Quality Setting
NO
SUPER BEST / BEST / HIGH / NORMAL
USB Mouse Control
YES
Motion Detection Area
16 × 12 grids per channel
Motion Detection Sensitivity
Event Notification
3 adjustable parameters for accurate detection
Push Video / Push Status /
FTP / E-Mail
Push Status / FTP / E-Mail
Picture Zoom
2X digital zoom
PTZ Control
Alarm I/O
YES
4 inputs, 1 output
NO
RS485
YES
IR Remote Control
NO
YES (IR receiver built-in)
Key Lock (Password Protection)
User Level
Our brand’s PTZ camera only
YES
4 user levels for different access privilege
64
APPENDIX 1 SPECIFICATIONS
Model 1
Model 2
Model 3
 General
Video Loss Detection
YES
Camera Title
Supports up to 25 letters
Video Adjustable
Hue / Saturation / Contrast / Brightness
Date Display Format
YY/MM/DD, DD/MM/YY & MM/DD/YY
Daylight Saving
YES
Power Source (±10%)
DC12V / 3A
Operating Temperature
10℃ ~ 40℃ (50℉~104℉)
Operating Humidity
10% ~ 85%
Dimensions (mm)***
Net Weight (kg)
DC12V / 2A
345(W) × 58.8(H) × 223(D)
260(W) x 48(H) x 223(D)
2.17
--
 Network
Ethernet
10/100 Base-T. Supports remote control and live view via Ethernet
Network Protocol
TCP/IP, PPPOE, DHCP and DDNS
 Remote Surveillance from PC
Compatible Operating System
Compatible Program
Windows & MAC
Web Browser:
Internet Explorer, Google Chrome & Safari
CMS Lite:
32CH central management software for Windows OS
QuickTime:
For both Windows and MAC operating systems
Max. online users
20
Web Transmitting Compression Format
H.264
Network Live Audio
YES
Remote Independent Operation
YES
Remote Event Download & Playback
YES
 Mobile Surveillance
App
EagleEyes
Compatible Devices
Push Video
iOS & Android mobile devices
YES (4CH)
NO
Push Status
YES
 Others
EaZy Networking
IVA Support
YES
YES
(4 channels in analog mode)
NO
DCCS Support
YES
Free DDNS service
YES
Privacy Mask
YES
Multiplex Operation
System Recovery
Optional Peripherals
Live display / record / playback / backup / network operations
System auto recovery after power failure
Disk Array (AVX997 / AVX992) /
HDMI Matrix (HDM02) /
USB Joystick (AVX102)
HDMI Matrix (HDM02) / USB Joystick (AVX102)
* The specifications are subject to change without notice.
** To see 5MP video playback, you need to backup the footage and play on PC.
*** Dimensional tolerance: ±5mm
65
APPENDIX 1 SPECIFICATIONS

8CH Model
Model 4
Model 5
Model 6
Model 7
 Video
Video System
NTSC / PAL (auto detection)
Video Compression Format
H.264
Video Signal
IP / TVI / Analog HD / 960H
Analog HD / TVI / 960H
Video Input
8 quadbrid channels (IP / TVI / Analog HD /
960H) + 1 IP channel
8 tribrid channels
Video Input
Interface
Analog Mode
IP Mode
Video Output
Ethernet, 10/100 Base-T
NO
BNC
VGA
HDMI
Video Resolution
Composite video signal 1 Vp-p 75Ω BNC
YES
YES
(up to 1080P resolution)
YES
YES
(up to 4K2K resolution)
YES
Analog Mode
1080P / 720P / QHD / 960H / Frame / Field / CIF
IP Mode
Live & Playback:
1920 x 1080 /
1280 x 720 /
640 x 480 / 320 x 240
Record**:
2592 x 1944 /
2048 x 1536 /
1920 x 1080 /
1280 x 720 /
640 x 480 / 320 x 240
2592 x 1944** /
2048 x 1536** /
1920 x 1080 /
1280 x 720 /
640 x 480 / 320 x 240
NO
 Record & Backup
Max. Recording
Rate
Analog Mode
IP Mode
Up to 240 IPS @
1920 x 1080
(8 channels)
Up to 120 IPS @ 1920 x 1080 (8 channels)
Up to 240 IPS @ 1280 x 720 (8 channels)
--
UP to 270 IPS @ 1920 x 1080 (9 channels)
Recording Mode
Manual / Timer / Motion / Alarm / Remote
Pre-alarm Recording
YES
Playback Channel
9CH
8CH
Quick Search
Time / Motion / Alarm search mode
Backup Device
USB 2.0 flash drive / Network
Regular Backup
YES
 Audio
Audio Input
4 audio inputs
1 audio input
Audio Output (Mono)
1 audio output
1 audio output
 General
Hard Disk Storage
6TB SATA HDD x 3
6TB SATA HDD x 2
SATA Interface
eSATA Interface
(For external disk array connection)
Image Quality Setting
YES
YES
NO
SUPER BEST / BEST / HIGH / NORMAL
USB Mouse Control
YES
Motion Detection Area
Motion Detection Sensitivity
Event Notification
16 × 12 grids per channel
3 adjustable parameters for accurate detection
Push Video / Push Status / FTP / E-Mail
Push Status / FTP / E-Mail
Picture Zoom
2X digital zoom
PTZ Control
YES
66
APPENDIX 1 SPECIFICATIONS
Model 4
Model 5
Model 6
Model 7
 General
Alarm I/O
8 inputs, 1 output
4 inputs, 1 output
RS485
YES
IR Remote Control
NO
YES (IR receiver built-in)
Key Lock (Password Protection)
YES
User Level
4 user levels for different access privilege
Video Loss Detection
YES
Camera Title
Supports up to 25 characters
Video Adjustable
Hue / Saturation / Contrast / Brightness
Date Display Format
YY/MM/DD, DD/MM/YY & MM/DD/YY
Daylight Saving
Power Source (±10%)
YES
19V / 3.42A
12V / 3A
Operating Temperature
10℃ ~ 40℃ (50℉~104℉)
Operating Humidity
Dimensions (mm)***
Net Weight (kg)
4 inputs
10% ~ 85%
430(W) x 65(H) x
338(D)
345(W) x 68.3(H) x 225(D)
--
2.17
---
 Network
Ethernet
10/100 Base-T. Supports remote control and live view via Ethernet
Network Protocol
TCP/IP, PPPOE, DHCP and DDNS
 Remote Surveillance from PC
Compatible Operating System
Compatible Program
Windows & MAC
Web Browser:
CMS Lite:
QuickTime:
Internet Explorer, Google Chrome & Safari
32CH central management software for Windows OS
For both Windows and MAC operating systems
Max. online users
20
Web Transmitting Compression Format
H.264
Network Live Audio
YES
Remote Independent Operation
YES
Remote Event Download & Playback
YES
 Mobile Surveillance
App
EagleEyes
Compatible Devices
Push Video
iOS & Android mobile devices
YES (4CH)
NO
Push Status
YES
 Others
EaZy Networking
IVA Support
YES
YES (4 channels in analog mode)
NO
DCCS Support
YES
Free DDNS service
YES
Privacy Mask
YES
Multiplex Operation
Live display / record / playback / backup / network operations
System Recovery
Optional Peripherals
System auto recovery after power failure
Disk Array (AVX997 / AVX992) / HDMI Matrix
(HDM02) / USB Joystick (AVX102)
HDMI Matrix (HDM02) / USB Joystick (AVX102)
* The specifications are subject to change without notice.
** To see 5MP video playback, you need to backup the footage and play on PC.
*** Dimensional tolerance: ±5mm
67
APPENDIX 1 SPECIFICATIONS

16CH Model
Model 8
Model 9
 Video
Video System
NTSC / PAL (auto detection)
Video Compression Format
H.264
Video Signal
IP / TVI / Analog HD / 960H
Video Input
16 quadbrid channels (IP / TVI / Analog HD / 960H),
within which IP channels are up to 9 channels
Video Input Interface
Analog Mode
Composite video signal 1 Vp-p 75Ω BNC
IP Mode
Video Output
BNC
YES
VGA
YES (up to 1080P resolution)
HDMI
Video Resolution
Ethernet, 10/100 Base-T
Analog Mode
IP Mode
2 ports (up to 4K2K resolution)
1 port (up to 4K2K resolution)
1080P / 720P / QHD / 960H / Frame / Field / CIF
2592 x 1944** / 2048 x 1536** / 1920 x 1080 / 1280 x 720/ 640 x 480 / 320 x 240
 Record & Backup
Max. Recording Rate
Analog Mode
Up to 480 IPS @ 1920 x 1080 (16 channels)
IP Mode
UP to 270 IPS @ 1920 x 1080 (9 channels)
Recording Mode
Manual / Timer / Motion / Alarm / Remote
Pre-alarm Recording
YES
Playback Channel
16CH
Quick Search
Time / Motion / Alarm search mode
Backup Device
USB 2.0 flash drive / Network
Regular Backup
YES
 Audio
Audio Input
8 audio inputs
Audio Output (Mono)
2 audio outputs
 General
Hard Disk Storage
6TB SATA HDD x 3
SATA Interface
YES
eSATA Interface
(For external disk array connection)
YES
Image Quality Setting
SUPER BEST / BEST / HIGH / NORMAL
USB Mouse Control
YES
Motion Detection Area
Motion Detection Sensitivity
Event Notification
16 × 12 grids per channel
3 adjustable parameters for accurate detection
Push Video / Push Status / FTP / E-Mail
Picture Zoom
2X digital zoom
PTZ Control
YES
Alarm I/O
8 inputs, 1 output
RS485
YES
IR Remote Control
YES (IR receiver built-in)
Key Lock (Password Protection)
User Level
YES
4 user levels for different access privilege
Video Loss Detection
YES
Camera Title
Video Adjustable
Supports up to 25 letters
Hue / Saturation / Contrast / Brightness
Date Display Format
YY/MM/DD, DD/MM/YY & MM/DD/YY
Daylight Saving
YES
68
APPENDIX 1 SPECIFICATIONS
Model 10
Model 11
 General
Power Source (±10%)
19V / 3.42A
Operating Temperature
10℃ ~ 40℃ (50℉~104℉)
Operating Humidity
10% ~ 85%
Dimensions (mm)***
432(W) × 90(H) × 326(D)
 Network
Ethernet
10/100 Base-T. Supports remote control and live view via Ethernet
Network Protocol
TCP/IP, PPPOE, DHCP and DDNS
 Remote Surveillance from PC
Compatible Operating System
Compatible Program
Windows & MAC
Web Browser:
CMS Lite:
QuickTime:
Internet Explorer, Google Chrome & Safari
32CH central management software for Windows OS
For both Windows and MAC operating systems
Max. online users
20
Web Transmitting Compression
Format
H.264
Network Live Audio
YES
Remote Independent Operation
YES
Remote Event Download & Playback
YES
 Mobile Surveillance
App
EagleEyes
Compatible Devices
iOS & Android mobile devices
Push Video
YES (4CH)
Push Status
YES
 Others
EaZy Networking
YES
IVA Support
YES (4 channels in analog mode)
DCCS Support
YES
Free DDNS service
YES
Privacy Mask
YES
Multiplex Operation
System Recovery
Optional Peripherals
Live display / record / playback / backup / network operations
System auto recovery after power failure
Disk Array (AVX997 / AVX992) / HDMI Matrix (HDM02) / USB Joystick (AVX102)
* The specifications are subject to change without notice.
** For 3MP / 5MP video recording, the local live display and playback only support sub stream display (D1 by default).
*** Dimensional tolerance: ±5mm
69
APPENDIX 1 SPECIFICATIONS

16CH Model
Model 10
Model 11
Model 12
 Video
Video System
NTSC / PAL (auto detection)
Video Compression Format
H.264
Video Signal
IP / TVI / Analog HD / 960H
Analog HD / TVI / 960H
Video Input
16 quadbrid channels
(IP / TVI / Analog HD / 960H),
within which IP channels are up
to 9 channels
16 tribrid channels
Composite video signal 1 Vp-p
75Ω BNC
Composite video signal 1 Vp-p 75Ω BNC
Ethernet, 10/100 Base-T
NO
Video Input Interface
Analog Mode
IP Mode
Video Output
Video Resolution
BNC
YES
VGA
YES (up to 1080P resolution)
YES
HDMI
YES (up to 4K2K resolution)
YES
Analog Mode
IP Mode
1080P / 720P / QHD / 960H / Frame / Field / CIF
2592 x 1944** / 2048 x 1536** /
1920 x 1080 / 1280 x 720/
640 x 480 / 320 x 240
NO
 Record & Backup
Max. Recording Rate
Analog Mode
IP Mode
Up to 240 IPS @ 1920 x 1080 (16 channels)
Up to 480 IPS @ 1280 x 720 (16 channels)
UP to 270 IPS @ 1920 x 1080
(9 channels)
Recording Mode
NO
Manual / Timer / Motion / Alarm / Remote
Pre-alarm Recording
YES
Playback Channel
16CH
Quick Search
Time / Motion / Alarm search mode
Backup Device
USB 2.0 flash drive / Network
Regular Backup
YES
 Audio
Audio Input
4 audio inputs
1 audio input
Audio Output (Mono)
1 audio output
1 audio output
 General
Hard Disk Storage
6TB SATA HDD x 3
SATA Interface
eSATA Interface
(For external disk array connection)
Image Quality Setting
YES
YES
NO
SUPER BEST / BEST / HIGH / NORMAL
USB Mouse Control
YES
Motion Detection Area
Motion Detection Sensitivity
Event Notification
16 × 12 grids per channel
3 adjustable parameters for accurate detection
Push Video / Push Status /
FTP / E-Mail
Push Status / FTP / E-Mail
Picture Zoom
2X digital zoom
PTZ Control
YES
Alarm I/O
8 inputs, 1 output
4 inputs
YES
NO
RS485
IR Remote Control
YES (IR receiver built-in)
Key Lock (Password Protection)
User Level
YES
4 user levels for different access privilege
70
APPENDIX 1 SPECIFICATIONS
Model 10
Model 11
Model 12
 General
Video Loss Detection
YES
Camera Title
Supports up to 25 letters
Video Adjustable
Hue / Saturation / Contrast / Brightness
Date Display Format
YY/MM/DD, DD/MM/YY & MM/DD/YY
Daylight Saving
YES
Power Source (±10%)
19V / 3.42A
Operating Temperature
10℃ ~ 40℃ (50℉~104℉)
Operating Humidity
10% ~ 85%
Dimensions (mm)***
430(W) x 65(H) x 338(D)
 Network
Ethernet
10/100 Base-T. Supports remote control and live view via Ethernet
Network Protocol
TCP/IP, PPPOE, DHCP and DDNS
 Remote Surveillance from PC
Compatible Operating System
Compatible Program
Windows & MAC
Web Browser:
Internet Explorer, Google Chrome & Safari
CMS Lite:
32CH central management software for Windows OS
QuickTime:
For both Windows and MAC operating systems
Max. online users
20
Web Transmitting Compression
Format
H.264
Network Live Audio
YES
Remote Independent Operation
YES
Remote Event Download & Playback
YES
 Mobile Surveillance
App
EagleEyes
Compatible Devices
Push Video
iOS & Android mobile devices
YES (4CH)
NO
Push Status
YES
 Others
EaZy Networking
IVA Support
YES
YES
(4 channels in analog mode)
NO
DCCS Support
YES
Free DDNS service
YES
Privacy Mask
YES
Multiplex Operation
System Recovery
Optional Peripherals
Live display / record / playback / backup / network operations
System auto recovery after power failure
Disk Array (AVX997 / AVX992) /
HDMI Matrix (HDM02) /
USB Joystick (AVX102)
HDMI Matrix (HDM02) / USB Joystick (AVX102)
* The specifications are subject to change without notice.
** For 3MP / 5MP video recording, the local live display and playback only support sub stream display (D1 by default).
*** Dimensional tolerance: ±5mm
71
APPENDIX 2 PUSH VIDEO CONFIGURATION
APPENDIX 2 PUSH VIDEO CONFIGURATION
Note: This function is for selected models only.
A2.1 Alarm Sensor Connection
Connect the alarm sensor, such as magnetic contacts, to the alarm-in port on the DVR rear panel. Alarm-in 1
corresponds to video channel 1, alarm-in 2 corresponds to video channel 2, and so on.
Note: The voltage restriction for alarm-in device connection is under DC24V 1A.
72
APPENDIX 2 PUSH VIDEO CONFIGURATION
A2.2 Configuration
Before configuring Push Video, make sure:
1. The DVR system is set up as described in “2. CONNECTION AND SETUP” at page 4.
2. The DVR is connected to Internet.
3. You’ve installed the app, EagleEyes, on your iOS or Android mobile devices.
For details, please refer to “7.2 Mobile Devices” at page 62.
Step1: Right click to show the main menu.
Go to
(ADVANCED CONFIG.)  NOTIFY. In PUSH VIDEO, select the alarm device you want, and
configure the alarm type. For details, please refer to “PUSH VIDEO” at page 49.
ADVANCED CONFIG
CANERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
DCCS
NOTIFY
JOYSTICK
PUSH VIDEO
PUSH STATUS
MESSAGE MAIL
MAIL
FTP
RESET ALL GUARD CONNECTION
SUBMIT
ALARM TRIGGERED DEVICE
ALARM IN 1
CH01
ALARM OFF / INTERNAL ALARM
CH02
ALARM OFF
CH03
ALARM N.O.
CH04
ALARM OFF





CH1
CH2
office
CH4
EXIT
Step2: Open EagleEyes, and add this DVR to the EagleEyes address book.
Step3: Enable Push Video as described below, and try to trigger your sensor to see if you can receive Push Video
successfully.
73
APPENDIX 3 SET PUSH VIDEO
APPENDIX 3 SET PUSH VIDEO
This DVR series supports instant event notifications to your iOS / Android mobile device with our self-developed
program, “EagleEyes”, installed. When a man is detected by an external alarm device, the DVR will immediately
receive alarm signals and send to your iOS / Android mobile device.
Note: iOS and Android are the trademarks or registered trademarks of their respective holders.
A3.1 Prerequisite
Before setting this function, make sure you have checked the following:
 You have an iOS or Android mobile device with our self-developed program, “EagleEyes”, installed. For details, please
refer to the previous chapter.
 An external alarm device is connected to the external I/O ports on the rear panel. Make sure a camera is also connected
to record for alarm occurrences. To know which video channel corresponds to which alarm pin, please refer to
“APPENDIX 2 PUSH VIDEO CONFIGURATION” at page 72.
 The event record function of your DVR is not disabled.
 The motion detection function of your DVR is not disabled.
 Your DVR is connected to Internet. For details, please refer to
www.surveillance-download.com/user/network_setup/network_setup_recorder.pdf.
74
APPENDIX 3 SET PUSH VIDEO
A3.2 Enable Push Video
A3.2.1 From iOS Mobile Device (iPhone / iPad)
Step1: In the iPhone / iPad main menu, select Settings  Notifications. Select EagleEyes, and make sure
the notification is set to on.
Step2: Open EagleEyes, and switch Guard to ON. You’ll receive the message indicating that Push Video is on.
Step3: Return to the main page or standby page of iPhone / iPad. You’ll receive event notifications when there’s
an alarm event. Follow the on-screen instruction to immediately play the recorded clip.
75
APPENDIX 3 SET PUSH VIDEO
A3.2.2 From Android Mobile Device
In the address book, switch Guard from OFF to ON.
76
APPENDIX 4 COMPATIBLE USB FLASH DRIVE LIST
APPENDIX 4 COMPATIBLE USB FLASH DRIVE LIST
Please upgrade the firmware of the DVR to the latest version to ensure the accuracy of the following table. If the
USB flash drive is not supported by the DVR, you will see
on the screen.
Note:
Please use your PC to format the USB flash drive as “FAT32”.
Note:
You can backup up to 2GB video data for one-time USB backup. To backup more data, please set
the time & channel(s) you want, and start USB backup again.
MANUFACTURER
MODEL
CAPACITY
Transcend
JFV35
4GB
JFV30
8GB
Kingston
DataTraveler
1GB
PQI
U172P
4GB
Apacer
AH320
2GB
AH320A
8GB
AH220
1GB
AH320
4GB
A-data
RB-18
1GB
Sandisk
Cruzer Micro
2GB
Cruzer Micro
4GB
Cruzer4-pk
2GB
Netac
U208
1GB
MSI
F200
4GB
SONY
Micro Vault Tiny 2GB
2GB
Micro Vault Tiny 4GB
4GB
Micro Vault Tiny
1GB
77
APPENDIX 5 COMPATIBLE SATA HDD LIST
APPENDIX 5 COMPATIBLE SATA HDD LIST
Please upgrade the firmware of the device to the latest version to ensure the accuracy of the following table.
Note: It’s necessary to install a hard disk first before firmware upgrade to ensure the upgrade process
works properly.
Note: To use a green hard disk, use ONLY the hard disk designed especially for surveillance to ensure the
device works properly.
MODEL
Pipeline HD
ST3500312CSS
Pipeline HD
ST500VT000
Pipeline HD
ST1000VM002
Pipeline HD
ST1000VM002
Seagate*
CAPACITY
MODEL
CAPACITY
500GB
ST3000VX004
3TB
500GB
ST3000VX005
3TB
1TB
ST3000VX006
3TB
1TB
ST3000VX000
3TB
ST31000525SV
1TB
ST4000VM000
4TB
ST31000340AS
1TB
ST4000VX000
4TB
ST1000VX000
1TB
ST4000VX002
4TB
ST1000VX002
1TB
ST4000VX007
4TB
ST1000VX001
1TB
ST6000VX0001
6TB**
ST1000VX005
1TB
ST6000VX0011
6TB**
ST2000VX000
2TB
ST6000NM0024
6TB**
ST2000DM001
2TB
ST8000VX002
8TB**
ST2000VX004
2TB
ST8000VX0022
8TB**
ST3000VM002
3TB
ST100000VX0004
10TB**
WD
MODEL
CAPACITY
MODEL
CAPACITY
WD10PURX
1TB
WD30EFRX
3TB
WD20PURX
2TB
WD40PURX
4TB
WD20EURS
2TB
WD40EURX
4TB
WD20EURX
2TB
WD60EURX
6TB**
WD20EFRX
2TB
WD60PURX
6TB**
WD2002FAEX
2TB
WD6001FFWX
6TB**
WD30PURX
3TB
WD6001FSYZ
6TB**
WD30EURX
3TB
TOSHIBA
MODEL
CAPACITY
MODEL
CAPACITY
DT01ACA050
500GB
MD03ACA200V
2TB
DT01ABA050V
500GB
DT01ABA300V
3TB
DT01ACA100
1TB
DT01ACA300
3TB
DT01ABA100V
1TB
MD03ACA300V
3TB
DT01ACA200
2TB
MD03ACA400V
4TB
DT01ABA200V
2TB
MD04ABA500V
5TB
* To know more details about SRS and its related support and service, please contact your local Seagate representative directly.
** Please be advised to pay attention to the heat dissipation of the hard disk which is over 4TB because it might generate much heat
during operation. It’s recommended that ambient temperature is not over 35°C.
78
APPENDIX 6 MAIN MENU STRUCTURE
APPENDIX 6 MAIN MENU STRUCTURE
QUICK START
GENERAL
CHANNEL TITLE
EVENT STATUS
DATE DISPLAY
DCCS DISPLAY
MOUSE SENSITIVITY
AUDIO GAIN
RECORD CONFIG
TIME SETUP
DATE
TIME
NTP SERVER
FORMAT
SYNC PERIOD
GMT
DAYLIGHT
EaZy
SYSTEM
ACCOUNT
TOOLS
LANGUAGE
UPGRADE
NETWORK UPGRADE
BACKUP CONFIG
RESTORE CONFIG
UPGRADE CAMERA PARAMETERS
UPGRADE CAMERA FIRMWARE
SYSTEM INFO
BAUD RATE
HOST ID
R.E.T.R.
AUTO KEY LOCK(S)
CLEAR HDD
RESET DEFAULT
REMOTE CONTROL ID
DEVICE TITLE
SERIAL TYPE
VIDEO FORMAT
VERSION
ONLINE
ANONYMOUS VIEWER LOGIN
LOGIN WITH CAPTCHA IMAGE
DROP ALL VIDEO CONNECTION
LOGIN FAILURE TIMES
LOCK TIME FOR LOGIN FAILURES
BACKUP DATA
BACKUP LOG
EVENT INFORMATION
QUICK SEARCH
EVENT SEARCH
HDD INFO
EVENT LOG
ADVANCED CONFIG
CAMERA
INTERFACE
CAMERA TYPE* / CONNECTION*
BRIGHTNESS
CONTRAST
SATURATION
HUE
REC
TIME STAMP DISPLAY
CHANNEL TITLE
REC AUDIO
ALARM OUT DURATION (SECS)
79
APPENDIX 6 MAIN MENU STRUCTURE
ADVANCED CONFIG
DETECTION
LS
SS
TS
MOTION
ALARM
AREA
PRIVACY MASK
INTERNAL ALARM*
CAMERA GUARD
ALERT
EXT. ALERT
INT. BUZZER
KEY BUZZER
VLOSS BUZZER
MOTION BUZZER
ALARM BUZZER
HDD BUZZER
ALARM DURATION (SEC)
HDD FAILURE BUZZER
HDD NEARLY FULL (GB)
HDD OVERHEAT ALERT (°C)
HDD FAILURE BUZZER
NETWORK
WAN
E-MAIL
DDNS
PROTOCOL
EaZy
DISPLAY
FULL SCREEN DURATION
QUAD SCREEN DURATION*
HDD DISPLAY MODE
HDMI RESOLUTION
VGA RESOLUTION*
SPOT MONITOR
RECORD
MANUAL RECORD
EVENT RECORD
TIMER RECORD
PRE-ALARM RECORD
OVERWRITE
KEEP DATA LIMIT (DAYS)
RECORD CONFIG
SUBSTREAM RESOLUTION
DEVICES*
DCCS
IVS*
NOTIFY
PUSH VIDEO*
PUSH STATUS
MESSAGE MAIL
MAIL
FTP
JOYSTICK
SCHEDULE SETTING
RECORD
DETECTION
ALARM IN*
ALARM OUT*
PUSH VIDEO*
BUZZER
REGULAR REPORT*
AUTO BACKUP*
REGULAR REBOOT*
*For selected models only
80
APPENDIX 7 DVR BATTERY REPLACEMENT
APPENDIX 7 DVR BATTERY REPLACEMENT
DVR time reset after power failure, for example, caused by a power outage, will cause the disorder of the recorded data,
and users may have problems in searching the event clip they want. To keep the DVR time from resetting, a
non-chargeable lithium battery, CR2032, is installed in the DVR.
However, the DVR time might still get reset when the DVR battery is low or even running out of power. If so, please
replace the DVR battery, CR2032, right away as instructed below.

How to replace CR2032
Note: The lithium battery, CR2032, is a non-chargeable battery, and should be purchased separately.
Please replace only with the same or equivalent type battery in case of danger.
Step1: Stop all DVR recording immediately to prevent the disorder of the recorded data. Then, back up the
recorded data if necessary.
Step2: Power off the DVR, and disconnect the DVR power.
Step3: Remove the DVR cover, and find the battery on the mainboard.
Step4: Push the release as indicated below to remove the battery.
Step5: Get a new battery with the side of “CR2032” facing up, and install it to the mainboard.
Step6: Replace the DVR cover and connect to power.
Step7: Set DVR date & time, and resume recording. For details, please refer to “6.1.2 TIME SETUP” at page 25,
and “6.4.6 RECORD” at page 42.
81
APPENDIX 8 EAZY NETWORKING
APPENDIX 8 EAZY NETWORKING
EaZy Networking is a free P2P cloud service to connect AVTECH devices to the Internet automatically by
plug-and-play, enabling you to check the live view via your mobile device or laptop at anytime (in 64 kbps). Should
you feel the live view is not fluent enough and would like to speed it up, AVTECH provides several data plans for
you to subscribe. We've also offered 2GB data allowance as a gift on each device for you to experience. When
2GB is up, the network transmission speed will restore to what it should be.
In most cases, the device is connected via P2P. Connection via the relay server is only applied to some complex
environments such as the private IP-based network environment used by a large enterprise.
EaZy Networking could be configured via EagleEyes on an iOS / android device, or via Internet Explorer.
Before using this function, make sure:
 This DVR is connected to a switch or router, and the switch or router is ready for Internet connection.
 The network icon on the top right corner is
, not
.
 You have an iOS / Android mobile device with EagleEyes installed, or a PC / laptop with Internet Explorer
installed.
A8.1 Via EagleEyes on iOS / Android Device
A8.1.1 Setup
Step1: Right-click to show the main menu, and select “NETWORK”  “WAN”. Set "NETWORK TYPE” to “DHCP”,
and make sure the network icon on the top right corner is changed from
to
.
Note: If the setting is made via the Setting Wizard, the network type will be automatically switched to
DHCP.
ADVANCED CONFIG
CAMERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
DEVICES
DCCS
IVS
NOTIFY
JOYSTICK
EXIT
WAN E-MAIL DDNS PROTOCOL EaZy
NETWORK TYPE
IP
GATEWAY
NETMASK
PRIMARY DNS
SECONDARY DNS
PORT
CHECK INTERNET AVAILABILITY BY ADDRESS
ENABLE UPNP
DHCP

192.168.001.010
192.168.001.254
255.255.255.000
8.8.8.8
168.95.1.1
80
www.google.com
OFF
MAC: 00:0E:53:EC:A7:B4
Step2: In the same menu, select “EaZy”. Enable EaZy Networking, and leave this page open. You’ll need to scan
the QR code later.
QUICK START
GENERAL
TIME SETUP
DAYLIGHT
EaZy
ENABLE EAZY NETWORKING
ON
EXIT
82
APPENDIX 8 EAZY NETWORKING
Step3: Open EagleEyes on your mobile device, and select “…” on the top left corner in the address book. Then,
click “
”.
Step4: Click “Login” in the section of “Cloud” and register an account for “Cloud Service”. If you’ve got an account,
please just log in.
Step5: Go back to the address book and click “+” to add a new device.
There are two methods to add new devices, “EaZy” and “Manual”.
Select “EaZy”, and choose the DVR icon to continue.
83
APPENDIX 8 EAZY NETWORKING
Step6: Click “
” in the section of “MAC address” to open the QR code scan page, and scan the QR code on the
DVR screen mentioned in Step2. The MAC address will be filled automatically.
Fill in the Captcha code manually, and click “Apply”.
Step7: Follow the on-screen instruction to finish the rest of the settings, and see if this device is added
successfully to the address book as a cloud device.
At the same time, you’ll be prompted to confirm if you want to remove the default user name and password.
 When the default user name and password are removed, you can ONLY use the user name and password of
the cloud service to access this recorder locally and remotely. If you forget the user name and password of the
cloud service, you could only reset the recorder and do all configurations again.
 When the default user name and password are kept, other people might be able to access this recorder if they
know the default user name and password of this recorder.
Confirm if you want to keep the default account to continue, and return to the address book. You’ll see the
newly-added device in the address with a cloud icon on it.
Step8: Click the newly-added device and see if you could access successfully.
84
APPENDIX 8 EAZY NETWORKING
A8.1.2 Checking Remaining Data Allowance
Step1: Log into the cloud service.
Step2: Select “Details” to go to account information, and select “Available Data Allowance”.
A8.1.3 Sharing Cloud Device Access to Other Account(s)
Note: One cloud device could be shared up to 30 cloud accounts, but the access to the device might be
failed because it is still restricted to the maximum online user setup of the device.
Step1: Log into the cloud service.
Step2: Select “Buddy” to go to the buddy sharing page. Then, choose the cloud device you want to share, and
switch from “OFF” to “Share”.
85
APPENDIX 8 EAZY NETWORKING
Step3: Enter the cloud account or the E-mail registered by the account, and select “Add”.
Step4: Check again the account to which you want to share your cloud device, and select “Next” to confirm and
continue.
Step5: Specify the access permission of the specified account, which account’s data allowance should be
consumed after access successfully, and how long the account is allowed to stay after access successfully.

Who should pay data allowance:
Who should pay
data allowance
The order to consume data allowance
I
The free data allowance provided by the device -> The additional data allowance shared to
other account(s) by the owner -> The additional data allowance of the device’s owner -> The
data allowance shared to other account(s) by the buddy
Buddy
The additional data allowance of the buddy -> The data allowance shared with other account(s)
by the buddy
Note: When there’s no data allowance to use, the network transmission will be down to 1 FPS. To restore
the fluency of live view, users need to subscribe a data plan from EagleEyes, or configure the
network settings by themselves.
86
APPENDIX 8 EAZY NETWORKING
Step6: Check again the configurations you made for the account to which you want to share your cloud device,
and select “Share!” to confirm.
Step7: (Optional) Configure the data allowance shared to other accounts to use.
Step8: Return to the address book of EagleEyes. You’ll see the device being shared is marked with an icon of two
people.
A8.2 Via Internet Explorer on PC / Laptop
Note: EaZy Networking setup via a web browser is only available on Internet Explorer.
A8.2.1 Setup
Step1: Right-click to show the main menu, choose
(ADVNACED CONFIG), select “NETWORK”  “WAN”.
Set "NETWORK TYPE” to “DHCP”, and make sure the network icon on the top right corner is changed
from
to
.
Note: If the setting is made via the Setting Wizard, the network type will be automatically switched to
DHCP.
ADVANCED CONFIG
CAMERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
DEVICES
DCCS
IVS
NOTIFY
EXIT
WAN E-MAIL DDNS PROTOCOL EaZy
NETWORK TYPE
IP
GATEWAY
NETMASK
PRIMARY DNS
SECONDARY DNS
PORT
CHECK INTERNET AVAILABILITY BY ADDRESS
MAC: 00:0E:53:EC:A7:B4
87
DHCP

192.168.001.010
192.168.001.254
255.255.255.000
8.8.8.8
168.95.1.1
80
www.google.com
APPENDIX 8 EAZY NETWORKING
Step2: In the same menu, select “EaZy”. Enable EaZy Networking, and write down the MAC address starting with
“000E53" under the QR code. You’ll need it later.
ADVANCED CONFIG
CAMERA
DETECTION
ALERT
NETWORK
DISPLAY
RECORD
DEVICES
DCCS
IVS
NOTIFY
EXIT
WAN E-MAIL DDNS PROTOCOL
ENABLE EAZY NETWORKING ON
EaZy
MAC: 00:0E:53:EC:A7:B4
ADVANCED CONFIG
GENERAL
TIME SETUP
DAYLIGHT
EaZy
ENABLE EAZY NETWORKING
ON
EXIT
Step3: Open Internet Explorer on a PC / laptop, and enter https://ez.eagleeyes.tw.
In the login page, register an account for “Cloud Service”. If you’ve got an account, please just log in.
Note: You PC must be connected to Internet.
Step4: For the first time to access this website, you’ll be prompted to install a plugin: EaZy Control. Please install
this plugin to ensure the service works properly.
Note: If you’re not prompted to install the plugin, please lower the security level of Internet Explorer,
and try to log into he cloud service again.
Step5: Click “+” to add a new device and you’ll be prompted to install a program, EaZy Wizard. Follow the
instructions to install this program.
88
APPENDIX 8 EAZY NETWORKING
Step6: Enable EaZy Wizard, and click “Start” to go to the login page. Log into the cloud service.
Step7: Select the recorder picture, or choose “DVR / NVR” on the bottom right corner. Then, enter the MAC
address you wrote down in Step2, and the security code.
Click “Apply” to continue.
Step8: When your device is found, you’ll be directed to the next page to change the device title if you want.
Note: The device name changed here will be fixed and can’t be changed later.
Click “Apply” to continue. You’ll be prompted to confirm if you want to remove the default user name and
password.
 When the default user name and password are removed, you can ONLY use the user name and password of
the cloud service to access this recorder locally and remotely. If you forget the user name and password of the
cloud service, you could only reset the recorder and do all configurations again.
 When the default user name and password are kept, other people might be able to access this recorder if they
know the default user name and password of this recorder.
Confirm if you want to keep the default account, and click “Apply” to continue and return to the main page.
89
APPENDIX 8 EAZY NETWORKING
Step9: You’ll see the newly-added device with a cloud icon on the main page. Click the device and see if you can
access the device successfully.
A8.2.2 Checking Remaining Data Allowance
Step1: Log into the cloud service.
Step2: Select “Account Information” on the top right corner to go to account information, and select “Available
Data Allowance”.
A8.2.3 Sharing Cloud Device Access to Other Account(s)
Note: One cloud device could be shared up to 30 cloud accounts, but the access to the device might be
failed because it is still restricted to the maximum online user setup of the device.
Step1: Log into the cloud service.
Step2: Select “Buddy Share” to go to the buddy sharing page. Then, choose the tag “Your own device(s)”, and
select “Share With Buddy”.
90
APPENDIX 8 EAZY NETWORKING
Step3: Choose the cloud device you want to share, and click “Next” to enter the cloud account or the E-mail
registered by the account you want to share with. Then, select “Add”.
Step4: Check again the account to which you want to share your cloud device.
To add more accounts, select “Add”; to remove the existing account, select “Delete”; to continue buddy
setup, select “Next”.
Step5: Specify the access permission of the specified account, which account’s data allowance should be
consumed after access successfully, and how long the account is allowed to stay after access successfully.

Who should pay data allowance:
Who should pay
data allowance
The order to consume data allowance
I
The free data allowance provided by the device -> The additional data allowance shared to
other account(s) by the owner -> The additional data allowance of the device’s owner -> The
data allowance shared to other account(s) by the buddy
Buddy
The additional data allowance of the buddy -> The data allowance shared with other account(s)
by the buddy
Note: When there’s no data allowance to use, the network transmission will be down to 1 FPS. To restore
the fluency of live view, users need to subscribe a data plan from EagleEyes, or configure the
network settings by themselves.
Step6: Check again the configurations you made for the account to which you want to share your cloud device,
and select “Share!” to continue.
Step7: (Optional) Configure the data allowance shared to other accounts to use.
91
APPENDIX 8 EAZY NETWORKING
Step8: Return to the main page. You’ll see the device being shared is marked with an icon of two people.
A8.3 Cloud Icons
Device connection ok
Device being shared to you
and connection ok
Device shared to other
account and connection ok
Device connection failed
Device being shared to you
and connection failed
Device shared to other
account and connection
failed
92
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising