advertisement
ATEX / IECEx Zone 2 and 22 UL Class I Division 2
Lumen X7 User Manual
7" Industry Tablet Type B7-A23.-2.../........
User Manual - Translation
7" Industry Tablet
- Lumen X7
Type B7-A23.-2.../……..
ATEX / IECEx Zone 2 / 22
UL Class I Division 2
Document No.: B1-A234-7D0001 / 391688
Revision 0 / Status: 23 March 2016
Proviso: Subject to technical changes. Changes, mistakes and printing errors do not substantiate any claim to damages.
Content
English
Page
1-61
BARTEC
GmbH
Max-Eyth-Straße 16
97980 Bad Mergentheim
Germany
Phone: +49 7931 597-0
Fax: +49 7931 597-119
Contact:
Download:
www.bartec.de/automation-download
Table of content
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Table of content
Subject to technical changes.
03/2016
- empty -
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
1. Basic Safety Information
1.1
Basic Safety Information
Information on this User Manual
Read carefully before putting the devices into operation.
The User Manual is a fixed part of the product. It must be kept in the direct vicinity of the device and the installation, operating and service staff must have access to it at all times.
The User Manual contains important information, safety instructions and test certificates which are necessary for the perfect function of the device in operation.
The User Manual is directed at all individuals concerned with the commissioning, handling and servicing of the product. The applicable guidelines and standards for areas with gas and dust atmosphere (99/92/EG, EN/IEC 60079-17 and EN/IEC 60079-19) must be observed when conducting this work.
Knowledge of the safety and warning information in this User Manual and the strict compliance with it is essential for safe installation and commissioning. Accidents, injuries and material damage can be avoided by circumspect handling and systematically following the instructions.
The examples, tables, and figures provided in this User Manual are for illustration purposes. Due to the different requirements of the respective application, the BARTEC company cannot assume responsibility or liability for actual use based on the examples and figures.
The BARTEC company reserves the right to carry out technical changes at any time.
In no event will BARTEC company be responsible or liable for indirect or consequential damages resulting from the use or application of this User Manual.
Safety and warning information is particularly emphasised in this User Manual and marked by symbols.
DANGER
DANGER describes a directly imminent danger. If not avoided, death or severe injury will be the consequence.
WARNING
WARNING describes a possibly imminent danger. If not avoided, death or severe injury may be the consequence.
CAUTION
CAUTION describes a possibly imminent danger. If not avoided, mild or slight injury may be the consequence.
ATTENTION
ATTENTION describes a possibly damaging situation. If not avoided, the plant or objects in its vicinity may be damaged.
Important information on effective, economical & environmentally compliant handling.
Subject to technical changes.
03/2016
EN 1/61
Basic Safety Information
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
1.1.1 Languages
The original User Manual with safety information is written in German. All other available languages are translations of the original User Manual.
The User Manual is available in German and English. If further languages are required, these must be requested from BARTEC or stated on placing an order.
1.1.2 Changes in the document
BARTEC reserves the right to change the content of this document without notification.
No warranty is assumed for the correctness of the information. In cases of doubt, the
German safety instructions apply because it is not possible to rule out errors of translation or printing. In the case of legal disputes, the “General Terms and Conditions of Business” of the BARTEC Group also apply.
The current versions of the datasheets, operating instructions, certificates and EC declarations of conformity can be downloaded from
www.bartec.de
under Products in the product area “Automation & Enterprise Mobility” or may be requested directly from
BARTEC GmbH.
1.1.3
1.2
1.3
Registered trademarks
ARM®
Android
Bluetooth®
Winmate is a registered trademark of ARM Limited is a registered trademark of Google Inc. is a registered trademark of Bluetooth Special Interest Group is a registered trademark of Winmate Communication, Inc.
Handling the product
The product described in this User Manual left the factory in a perfect and tested state in terms of safety. To maintain this state and to achieve a perfect and safe operation of this product, it may only be operated in the manner described by the manufacturer. In addition, the perfect and safe operation of this product requires correct transportation, proper storage and careful operation.
The safe and perfect handling of the Industry Tablet is a prerequisite for its perfect and correct functioning.
Intended use
1.3.1 Exclusive purpose
The Industry Tablet series is a handheld piece of electrical equipment. It serves the purpose of the mobile recording, processing and/or radio transmission of data within potentially explosive atmospheres.
EN 2/61
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Basic Safety Information
It is used exclusively in combination with devices which comply with the requirements placed on the overvoltage category I.
The admissible operating data of the device used must be considered.
1.3.2
1.4
1.5
1.6
Unintended use
Any other use is unintended and may lead to damage and accidents. The manufacturer shall not be liable for any use extending beyond the exclusive purpose.
Duties of the operator
The operator undertakes to only permit persons to work with the Industry Tablet who:
are acquainted with the basic regulations on safety and accident prevention, and who have been inducted in the use of the Industry Tablet,
have read and understood the documentation, the safety chapter and the warnings.
The operator checks that the safety and accident prevention regulations applicable to the respective case of use have been observed.
General safety information
Do not dry wipe or clean devices in potentially explosive atmospheres!
Do not open devices in potentially explosive atmospheres.
General statutory provisions or guidelines on occupational health and safety, accident prevention provisions and environmental protection laws must be heeded, e.g. Operational Safety Ordinance (BetrSichV) and nationally applicable ordinances.
Use suitable clothing and shoes with respect to the danger of hazardous electrostatic charges.
Avoid heat influences outside the specified temperature range.
Protect device from external influences! Do not expose device to caustic/aggressive liquids, vapours or spray. In the case of malfunction or damaged enclosure, remove the device immediately from the potentially explosive atmosphere and bring it to a safe place.
Maintenance
The pertinent erection and operating provisions for electrical systems must be observed!
(E.g. Directive 99/92/EC, Directive 94/9/EC, BetrSichV and nationally applicable ordinances EN 60079-14 and the series DIN VDE 0100)!
Observe the national waste disposal regulations when disposing of the devices.
Subject to technical changes.
03/2016
EN 3/61
Basic Safety Information
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
1.6.1 Servicing
No constant servicing will be necessary if operated correctly under consideration of the assembly instructions and environmental conditions. See Chapter “Service, inspection, repair” in this respect.
1.6.2 Inspection
According to EN/IEC 60079-17 and EN/IEC 60079-19, the operator of electrical systems in potentially explosive atmospheres is obliged to have these inspected by an electrician to ensure correct condition.
1.6.3
1.6.4
1.7
1.8
Repairs
Repairs to explosion-protected devices may only be performed by authorised personnel with original spare parts and according to the state of the art. The applicable provisions must be observed in this respect.
Commissioning
Labelling, test certificate and standards
Labels on explosion protection and the test certificate are attached to the Industry Tablet.
See Chapter 3 “Technical data” with respect to labelling.
The guidelines and standards applicable to the Industry Tablet for devices and protected systems for intended use in potentially explosive atmospheres are provided in Chapter 3
“Technical data”.
Warranty
It must be checked that all components and documents are available before commissioning.
WARNING
No changes or retrofits may be made without the written consent of the manufacturer.
If non-specified components are used, the explosion protection will no longer be guaranteed. In the case of externally procured parts, it is not guaranteed that these have been designed and manufactured in accordance with their load and requisite safety.
Contact the manufacturer before any changes or retrofits to receive a release.
Only use original spare and wearing parts.
EN 4/61
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Basic Safety Information
The manufacturer shall exclusively assume the complete warranty only for spare parts ordered from him.
Our “General Terms and Conditions of Sale and Delivery” shall apply in principle. These shall be made available to the operator on signing of contract at the latest. Warranty and liability claims in the case of injury and damage to property shall be excluded if they are attributable to one or several of the following causes:
−
Unintended use of the Industry Tablet.
−
Incorrect handling.
−
Failure to observe the information in the User Manual and the Quick Reference Guide with respect to transport, storage, commissioning, operation and service.
− Independent structural changes.
− Faulty monitoring of parts subject to wear and tear.
− Incorrectly performed repairs.
− Cases of disaster through the impact of foreign bodies and force majeure.
The BARTEC company grants a warranty period of three years starting from the date of delivery from the Bad Mergentheim factory on the Industry Tablets (exception: battery 6 months). The warranty period for accessories is one year starting from the date of delivery from the Bad Mergentheim factory. This warranty covers all parts of the delivery and shall be restricted to the free replacement or repair of the defective parts in our Bad
Mergentheim factory. For this purpose, any packaging supplied must be kept where possible. In the case of warranty, the goods must be returned to us after written agreement using an RMA form. There shall be no claim to repair at the sight of erection.
The information contained herein refers to the explosion-protected version of the Lumen
X7 Industry Tablet series.
This User Manual contains all important information on the subject of explosion protection.
A Quick Start Guide and further product information on handling and commissioning are similarly available.
1.9 Co-applicable documents - set of documents
−
User Manual for the Lumen X7 Industry Tablet series:
The use, commissioning and settings of the explosion-protected version of the
Industry Tablet series are described in this User Manual.
−
Quick Start Guide for the Lumen X7 Industry Tablet series:
The safety relevant information, initial use and further data on the explosion-protected version of the Industry Tablet series are described in this Quick Start Guide.
−
Technical Datasheet for the Lumen X7 Industry Tablet series:
This Technical Datasheet contains the most important explosion-relevant technical data as well as general technical data.
Subject to technical changes.
03/2016
EN 5/61
Basic Safety Information
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
1.10 Definition of terms
A few abbreviations are used in the documentation.
NI
Lumen X
= Non Incendive => is used as generic term for Zone 2 and Division 2 version
= stands for the entire explosion-protected product series
1.11 Configuration
The devices are only supplied with preinstalled operating system.
- Android 4.2.1 (Jelly Bean)
Customer software or further applications are not contained in the delivery.
This User Manual refers to the following configurations:
Configuration Version
Processor
ARM® Cortex™-A7 Quad Core 1.5 GHz
System memory
1 GB Mobile DDR2
16 GB eMMC
Main memory
Expandable memory
Micro SD card, supports up to 32 GB
Display
WLAN/WiFi
Bluetooth
WWAN
(optional)
GPS
Kamera
7" WSVGA TFT LCD with 1024 x 600 Pixel resolution
IEEE 802.11 a/b/g/n
Version 3.0 + EDR
3.75G - only data transfer
HSPA / UMTS / GPRS / WCDMA / GSM integrated
5 MP camera on the back
RFID NFC/HF
−
13,56 MHz
−
ISO 15693 (Read)
−
ISO 14443-A (Read)
−
ISO 18092 (Read/Write)
EN 6/61
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
2. Product Description
2.1 Lumen X7
Product Description
Lumen X7 Industry Tablets are tough tablets with 7" display, which have been designed for use in the industrial environments and especially developed by BARTEC for use in potentially explosive atmospheres.
The Lumen X7 Industry Tablet is based on the ARM Cortex-A7 Quad Core processor running at 1.5 GHz. The 7-inch capacitive multi-touch display offers 1024 x 600 pixel
WVGA resolution.
The Lumen X7 Industry Tablet owns a large number of international certifications and can be used worldwide. It is approved for ATEX/IECEx Zone 2 / 22 and UL Class I Division 2.
Further country approvals are available on request.
Because of its numerous functions, the Lumen X7 Industry Tablet is perfect for stock management, transport, maintenance technicians, operating personnel, engineers, and project managers afield and in industry.
2.2 Structure
Front and side view
Subject to technical changes.
03/2016
EN 7/61
Product Description
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
4
5
8
9
6
7
11
12
13
Position Designation
1
2
3
10
14
15
16
17
18
19
7” touch screen
Home button
Menu button
Description
Display and data input medium of the tablet
Returns to home screen
Opens a list of actions that the user can do on the current screen
Return button
Trigger button
Light sensor Controls the screen brightness
Battery status green Indicates the device is charging
Battery status red Indicates low battery
Power mode status Blue light: indicates Power On
Standard I/O cover
Volume up
Volume down
No light: indicates no Power
Prevents the access to the Inputs/Outputs in potentially explosive atmospheres
Increases the volume of music or radio
Audio Jack
(under cover)
Power Jack
(under cover)
Decreases the volume of music or radio
Connects a set of headphones, external speakers, or an audio device
DC-IN power input jack
USB ports
(under cover)
Connects USB flash drive 2.0 / mouse / printer / keyboard, etc
Memory card reader port for MicroSD Card
MicroSD Card
Reader (under cover)
3G Module/SIM card slot (under cover)
Docking connector
Service window to insert Micro SIM card also provides access to 3G module.
Port to docking solutions such as vehicle docking to provide power and external antenna
Power Button
Returns to the previous screen
If the device was equipped with scanners, this button can be function as a trigger button
Press and hold the button for 3 seconds to turn on the device
Press to turn on/off the screen
Press and hold the button for 3 seconds to select:
•
Power Off - to turn off the device press button for 8 Sec to force system power off
•
Airplane mode – to disable all wireless connections
•
Restart - to restart the device
EN 8/61
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Rear view
Product Description
Subject to technical changes.
03/2016
23
24
25
Position Designation
20 LED auxiliary light
21
22
Rear Camera
Optional Barcode
Battery
Speaker
2 x Battery Clips
Description
Provides lighting while using the camera
5 MP autofocus camera captures photos and videos
Barcode scanner for reading 1D/2D barcode is not available as certified version for use in hazardous locations.
Replaceable battery, battery with 3.7 V, 5300 mAh
Provides audio output for music and video
2 clips for battery lock and unlock
EN 9/61
Product Description
2.3
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Purpose of use
The Lumen X7 Industry Tablets are handheld electrical devices. They serve the purpose of entry, processing and (radio) transmission of data within potentially explosive atmospheres.
The Lumen X7 Industry Tablet is used exclusively in combination with devices which comply with the requirements placed on the overvoltage category I.
The Lumen X7 Industry Tablets, Type B7-A231-2…./…….. have been modified for use in the following potentially explosive atmospheres:
−
UL Class I Division 2
The Lumen X7 Industry Tablets, Type B7-A231-2…./…….. may not be used in the following zones:
− ATEX / IECEx Zone 0, 1, 2, 22 and 21
− Class II Division 2
− Class I, II Division 1
− Class III
The Lumen X7 Industry Tablets, Type B7-A234-2…./…….. have been modified for use in the following potentially explosive atmospheres:
−
ATEX / IECEx Zone 2 und Zone 22
−
UL Class I Division 2
The Lumen X7 Industry Tablets, Type B7-A234-2…./…….. may not be used in the following zones:
− ATEX / IECEx Zone 0, 1 and 21
− Class II Division 2
− Class I, II Division 1
− Class III
EN 10/61
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
3. Technical Data
3.1 Explosion protection NI
ATEX Zone 2 and 22
Type B7-A234-2…/……..
Labelling
Test certificate
Standards
Guidelines
Lumen X7
II 3G Ex ic IIC T5 Gc
II 3D Ex ic IIIB T100°C Dc
-10 °C ≤ Ta ≤ +50 °C
EPS 15 ATEX 1 037 X
EN 60079-0:2012 + A11:2013
EN 60079-11:2012
ATEX
EMV
R&TTE
RoHS
94/9/EG
2004/108/EG
1999/5/EG
2002/95/EG
IECEx Zone 2 and 22
Type B7-A234-2…/……..
Labelling
Test certificate
Standards
Lumen X7
Ex ic IIC T5 Gc
Ex ic IIIB T100°C Dc
-10 °C ≤ Ta ≤ +50 °C
IECEx EPS 15.0053X
IEC 60079-0:2011 Edition 6.0
IEC 60079-11:2011 Edition 6.0
UL Class I Division 2
Type
Type
B7-A234-2…/……..
B7-A231-2…/……..
Labelling
Test certificates
USA and Canada
Standards
Lumen X7
Class I Division 2
E321557 Vol 5 sec 1
ANSI/ISA 12.12.01-2013
CAN/CSA C22.2 No. 213-M1987
Technical Data
Subject to technical changes.
03/2016
EN 11/61
Technical Data
3.2
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
X - labelling (special conditions of use for secure operation within the potentially explosive atmosphere)
The ambient temperature range is -10 °C to +50 °C.*
The device must be protected from impact with high impact energy, from intense
UV-irradiation, and strongly charge generating processes.
It is not allowed to use connectors inside the potentially explosive atmosphere.*
It is not allowed to remove, change and/or charge the battery inside the potentially explosive atmosphere.*
*See individual chapter on the points in the User Manual.
Applicable standards
Explosion protection
EN 60079-0:2012 + A11:2013
EN 60079-11:2012
IEC 60079-0:2011
IEC 60079-11:2011
ANSI/ISA 12.12.01
Explosive atmospheres - Part 0: Equipment -
General requirements
Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
Explosive atmospheres - Part 0: Equipment -
General requirements
Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
ANSI/ISA-12.12.01-2013 Nonincendive Electrical
Equipment for Use in Class I and II, Division 2 and Class III, Divisions 1 and 2 Hazardous
(Classified) Locations
Electrical safety
IEC 60950-1 (ed.2); am1
CSA22.2 No. 60950-1-07
Information technology equipment - Safety -
Part 1: General requirements
Radio specification - WLAN / Bluetooth
Electromagnetic compatibility and radio spectrum
EN 300 328 V1.8.1: 2012 matters (ERM) – wideband transmission systems
– data transmission equipment operating in the
2.4 GHz ISM band and using wideband modulation techniques
EN 12/61
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Technical Data
Safety specification - Specific Absorption Rate (SAR)
Human exposure to radio frequency fields from hand-
EN 62209-2:2010 held and body-mounted wireless communication devices
– Human models, instrumentation and procedures – Part
2: Procedure to determine the specific absorption rate
(SAR) for wireless communication devices used in close proximity to the human body
RSS-132
Issue 3 January 2013
RSS-133
Issue 6 January 2013
Industry Canada: Cellular Telephone Systems Operating in the Bands 824-849 MHz and 869-894 MHz
Industry Canada: 2 GHz Personal Communications
Services
RSS-139
Issue 2 February 2009
RSS-210
Issue 8 December 2010
Industry Canada: Advanced Wireless Services (AWS)
Equipment Operating in the Bands 1710-1780 MHz and
2110-2180 MHz
Industry Canada: Licence-exempt Radio Apparatus (All
Frequency Bands): Category I Equipment
Safety specification - Laser and/or LED Products
EN 60825-1
Safety of laser products – Equipment classification and requirements
Electromagnetic compatibility (EMC)
Electromagnetic compatibility and radio spectrum matters
EN 300 440-1 V1.6.1:2010
(ERM) – short range devices – radio equipment to be used in the 1 GHz to 40 GHz frequency range – Part 1:
Technical characteristics and test methods
EN 300 440-2 V1.4.1:2010
Electromagnetic compatibility and radio spectrum matters
(ERM) – short range devices – radio equipment to be used in the 1 GHz to 40 GHz frequency range – Part 2:
Harmonised EN covering essential requirements of article
3.2 of the R&TTE Directive
EN 50566:2013
EN 55022: 2010
EN 55024: 2010
EN 61000-3-2: 2006 + A1:
2009 + A2: 2009
EN 61000-3-3: 2008
FCC Part 15 Class B
IC ICES-003
Product standard to demonstrate compliance of radio frequency fields from handheld and body-mounted wireless communication devices used by the general public (30 MHz - 6 GHz)
Information technology equipment – radio disturbance characteristics – limits and methods of measurement
Information technology equipment – radio disturbance characteristics – limits and methods of measurement
Limits – Limits for harmonic current emissions
(equipment input current <= 16 A per phase)
Limits – limitation of voltage charges, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current <=16 A per phase and not subject to conditional connection
EMC requirements in the USA: Testing for compliance with limits for a digital device of Class B
EMC requirements in Canada:
Testing for compliance with limits for a digital device of
Class B
Subject to technical changes.
03/2016
EN 13/61
Technical Data
3.3
3.3.1
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Features
Performance features
Processor
RAM
Main memory
Extension slot
Lumen X7 interfaces
(underneath the protection cover)
ARM® Cortex™-A7 Quad Core 1.5 GHz
1 GB Mobile DDR2
16 GB eMMC
Micro SD card slot supports up to 32 GB
It is not allowed to insert or change the card inside the potentially explosive atmosphere!
1 x SIM card slot
1 x Micro SD card slot
1 x Micro USB 2.0 type B (OTG)
1 x power connection (DC)
1 x audio combo connection
(Microphone In/Line-out)
1 x 7-pin docking connector (PoGo pin)
Interface for charging via desktop docking station
Operating system
Application availability
Software development
Android 4.2 (Jelly Bean)
Google App Store is pre-installed
Own development possible with standard Google
Android SDK.
Additional are the OS image, SDK and drivers available as download.
3.3.2 Physical features
Dimensions in mm/in
(Length x Width x Height)
Weight (with standard battery)
Display
Size
Brightness
Resolution
Touch
Interactive sensor technology
Keys on front side
(see also chapter 2.2 "Structure")
212.4 x 132.8 x 19 mm
(8.36 x 5.23 x 0.75 inch)
600 g (ca. 1.32 lb)
7"
500 cd/m² (nits)
1024 x 600 pixels projective capacitive multi-touch
- Light sensor
- G sensor
- Proximity sensor
- Digital compass
- 1 x Power on/off button
- 2 x Function button (F1, F2)
- 1 x Volume up/down button
- 4 x Home, Menue
EN 14/61
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Technical Data
3.3.3 User environment
Operating temperature
in battery mode
Operating temperature
In AC modus, only outside potentially explosive atmosphere
Operating temperature
during charging
Storage temperature
(without battery)
Air humidity
Class of protection (EN 60529)
-20 °C to +50 °C / -4 °F to +122 °F
-20 °C to +60 °C / -4 °F to +140 °F
0 °C to +40 °C / +32 °F to +104 °F
-30 °C to +60 °C /-22 °F to +140 °F
5 % to 95 % (non-condensing)
Ex-version IP 54
Non Ex-version IP65
3.3.4 Voice and data transmission Wi-Fi (Wireless LAN)
Wi-Fi connections are realised with the assistance of ARM® Cortex™-A7 Quad Core
1.5 GHz processor.
WLAN/WiFi radio module
Radio standard
Data rate
IEEE 802.11a/b/g/n
IEEE802.11a: up to 54 Mbit/Sec
IEEE802.11b: up to 11 Mbit/Sec
IEEE802.11g: up to 54 Mbit/Sec
IEEE802.11n: up to 65 Mbit/Sec
Frequency range
(country dependant)
Operating channels
IEEE802.11a: 5 GHz
IEEE802.11b: 2.4 GHz
IEEE802.11g: 2.4 GHz
IEEE802.11n: 2.4 GHz and 5 GHz
The actual operating channels and frequencies are subject to the applicable rules and the certification authorities in the respective country.
Wi-Fi alliance
Roaming
Aerial
Wi-Fi certified for 802.11a, 802.11b, 802.11g,
802.11n
Supports seamless roaming between the respective access points (802.11b, 802.11g, 802.11a/b/g und
802.11a/b/g/n) internal
3.3.5 Voice and data transmission Wireless WAN
WWAN radio module (optional)
HSPA / UMTS / GPRS / WCDMA /
GSM
GPS
Subject to technical changes.
03/2016
3.75G integrated
EN 15/61
Technical Data
3.3.6
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Voice and data transmission Bluetooth
Bluetooth-Verbindungen connections are realised with the assistance of ARM®
Cortex™-A7 Quad Core 1.5 GHz processor.
Bluetooth
Aerial
Version 2.1 or 3.0 + EDR internal
3.3.7 Audio
DANGER
Non-certified accessories endanger explosion protection.
Danger to life in a potentially explosive atmosphere!
Only use the audio connection outside the potentially explosive atmosphere!
3.3.8 Camera
5 MP camera with autofocus and LED flash on the back
3.3.9 RFID
The maximum read/write ranges of the RFID reader will depend on the different ambient conditions. For example:
- Transponder (tag), size
- Aerial used in the tag (size, model ...)
- Site of installation (metal, wood or other base)
- Ambient conditions
- External magnetic influences
- Temperature
- Humidity
Available option:
Internal NFC/HF Reader (High Frequency)
3.3.9.1 Internal HF reader
Supported standards
ISO 14443-A (Read)
ISO 15693 (Read)
ISO 18092 (Read/Write)
NXP Mifare_One (S50_4byte)
NXP Mifare_One (S70_4byte)
NXP Mifare_UltraLight C
NXP Mifare_One (S50_7byte)
NXP Mifare_UltraLight
TI HF-I Plus
TI HF-I Pro
NXPI-Code SLI
SONY Felica
SONY Felica Lite s
EN 16/61
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
3.3.10
3.4
Technical Data
NFC (Near Field Communication)
The communication between NFC-capable devices via active-active (Peer-To-Peer).
Supported standards
ISO 14443-A (Read)
ISO 15693 (Read)
ISO 18092 (Read/Write)
NXP Mifare_One (S50_4byte)
NXP Mifare_One (S70_4byte)
NXP Mifare_UltraLight C
NXP Mifare_One (S50_7byte)
NXP Mifare_UltraLight
NXP Mifare DesFire_EVI
TI HF-I Plus
TI HF-I Pro
NXPI-Code SLI
SONY Felica
SONY Felica Lite s
Battery
DANGER
Do not replace or charge the battery in a potentially explosive atmosphere.
Danger to life in a potentially explosive atmosphere!
Use original BARTEC/Winmate accessories only.
Do not open, disassemble, puncture, or crush the battery.
Do not leave or store the Lumen X7 Industry Tablet in an area which is near a heat source such as vehicle dashboard, dryer or other heat source.
Do not allow conductive objects to contact the battery.
Please contact your manufacturer if you suspect damage to your Lumen X7
Industry Tablet or battery for inspection and reparation.
The life of the battery will depend on different use factors and the device settings, e.g.:
- Use and setting of WLAN / Bluetooth
- Background lighting/screensaver
- The settings in power management
- Use and setting of the optional 3.75G module
- Use and setting of the RFID module
- Use and setting of the camera
Subject to technical changes.
03/2016
EN 17/61
Technical Data
3.5
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Battery Type B7-A2Z0-0027
Weight
Lithium polymer battery 3.7 V / 5300 mAh
130 g (ca. 0.286 lb)
Operating temperature
−
During charging
−
During discharging in potentially explosive atmosphere
0 °C to +45 °C / +32 °F to 113 °F
-20 °C to +50 °C / -4 °F to 122 °F
−
During discharging in safe atmosphere
-20 °C to +60 °C / -4 °F to 140 °F
Storage temperature
Relative air humidity
Lifecycle
Performance
Charging time
-20 °C to +50 °C / -4 °F to 122 °F
5 % to 95 % (non condensing)
≥ 300 depending on device settings, up to 12 hours
3 hours
External interfaces
DANGER
Non-certified accessories endanger the explosion protection.
Danger to life exists in potentially explosive atmospheres!
The external interfaces "Micro USB Type B (OTG Host, data exchange and charging), Pogo Pin (charging in docking station)" may only be used outside the potentially explosive range with accessories specified by the manufacturer.
Only use original BARTEC/Winmate accessories.
3.6 Product labelling
EN 18/61
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Description of the external interfaces
Warning
Camera
Technical Data
Type plate
Battery type B7-A2Z0-0027
Front side
Rear side
Subject to technical changes.
03/2016
EN 19/61
Technical Data
3.7
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Laser labels
The accessible laser radiation is in the visible spectral range (630 nm to 680 nm). It is not dangerous to the eye for short term exposure (up to 0.25 s).
NB:
In the case of laser devices of class 2, the eye is not in danger from incidental short term exposure to laser radiation, i.e. radiation exposure up to 0.25 s.
Laser devices of class 2 may therefore be used without protective measures if it is ensured that:
• neither intentional looking into the device is necessary for the application for a period longer than 0.25 s
• nor repeated looking into the laser radiation or reflected laser radiation.
In compliance with IEC 60825 and EN 60825, Clause 5 the following information is provided:
DEUTSCH
KLASSE 1
KLASSE 2
KLASSE 1 LASER PRODUKT
LASERLICHT
NICHT IN DEN LASERSTRAHL
SEHEN
KLASSE 2 LASER PRODUKT
ENGLISH
CLASS 1
CLASS 2
CLASS 1 LASER PRODUCT
LASER LIGHT
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
FRENCH / FRANÇAIS
CLASSE 1 PRODUIT LASER DE CLASSE 1
CLASSE 2
LUMIERE LASER NE PAS
REGARDER LE
RAYON FIXEMENT
PRODUIT LASER DE CLASSE 2
PORTUGUESE / PORTUGUÊS
CLASSE 1 PRODUTO LASER DA CLASSE 1
ITALIAN / ITALIANO
CLASSE 1
CLASSE 2
PRODOTTO AL LASER DI
CLASSE 1
LUCE LASER
NON FISSARE IL
RAGGIOPRODOTTO
AL LASER DI CLASSE 2
DUTCH / NEDERLANDS
KLASSE 1
KLASSE 2
KLASSE-1 LASERPRODUKT
LASERLICHT
NIET IN STRAAL STAREN
KLASSE-2 LASERPRODUKT
NORWEGIAN / NORSK
KLASSE 1
KLASSE 2
LASERPRODUKT, KLASSE 1
LASERLYS IKKE STIRR INN I
LYSSTRÅLEN
LASERPRODUKT, KLASSE 2
CLASSE 2
LUZ DE LASER NÃO FIXAR O
RAIO LUMINOSO
PRODUTO LASER DA CLASSE 2
DANISH / DANSK
KLASSE 1 KLASSE 1 LASERPRODUKT
KLASSE 2
LASERLYF
SE IKKE IND I STRÅLEN
KLASSE 2 LASERPRODUKT
FINNISH / SUOMI
LUOKKA 1 LUOKKA 1 LASERTUOTE
LUOKKA 2
LASERVALO
ÄLÄ TUIJOTA SÄDETTÄ
LUOKKA 2 LASERTUOTE
EN 20/61
Subject to technical changes.
03/2016
7” Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
4. Transport and Storage
4.1 Transport
Transport and Storage
Report any transport damage or incomplete deliveries immediately after receipt in writing to the forwarding company and BARTEC GmbH.
Any damage caused through incorrect storage shall not be covered by the warranty provisions of BARTEC GmbH.
4.2 Storage
ATTENTION
Property damage through incorrect storage!
Observe storage temperatures.
Keep humidity away from the Lumen X7 Industry Tablet.
Additional information on the batteries
The batteries of BARTEC (type B7-A2Z0-0027) are developed and manufactured in accordance with the highest industrial standards. The operating time or storage period of a battery is restricted, however. The actual life of a battery is influenced by different factors, e.g. hot, cold, rough operating environment and falling from a great height. If a battery is kept longer than six months, the performance may be impaired on a permanent basis. Keep the batteries in a dry, cool place. For longer periods of storage, remove the batteries from the device to prevent self-discharge.
Batteries kept for a duration of six months or longer should be charged and discharged again at least every three months. If electrolyte has escaped, do not touch the areas affected and dispose of the batteries as prescribed. Replace the battery if the operating time has shortened considerably.
The standard warranty period for all BARTEC batteries is six months, whereby it is irrelevant whether the battery was acquired separately or was contained in the scope of the delivery of the Industry Tablet.
Subject to technical changes.
03/2016
EN 21/61
Commissioning
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
5. Commissioning
5.1
5.1.1
DANGER
Avoid electrostatic charging in potentially explosive atmosphere.
Risk of fatal injury in an explosive atmosphere!
Do not dry wipe or clean the devices.
Wear suitable clothing and shoes.
Do not use rubber gloves or similar.
DANGER
Unintended use endangers explosion protection.
Risk of fatal injury in an explosive atmosphere!
Do not make any changes to the Lumen X7 Industry Tablet.
In the case of functional disturbances or damage to the enclosure, the device should be removed immediately from the potentially explosive atmosphere to a safe place. Remove battery to decommission the device!
Do not use any battery replicas or batteries from other manufacturers.
Before you assemble the device, make sure that all components and documents exist.
Scope of delivery
−
1 x 7" ex-certified Lumen X7 Industry Tablet
−
1 x battery
−
1 x hand strap
−
1 x capacitive stylus
−
1 x USB network adapter with EU plug
−
1 x USB network adapter with US plug
−
1 x USB cable (Type A to micro Type B)
−
1 x Quick Start Guide
Optional accessories
Authorized accessories from BARTEC
For the Ex area:
−
Replacement battery
−
Hand strap
−
1 x capacitive stylus
EN 22/61
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
For the non-Ex area:
−
USB network adapter for EU, UK, US and AUS
−
USB cable (Type A to micro Type B)
−
Micro USB Host cable (OTG)
−
Micro SD card
−
Screen protector
−
Charging station for Lumen X7 Industry Tablet
−
Battery charging station
−
Vehicle charging docking station
−
Vehicle charging adapter (Input 12 V DC, Output USB Type A)
−
Mobile power station
−
Hand strap
−
Leather case with screen protector ans shoulder strap
5.2
Commissioning
Requirements in potentially explosive atmosphere
Lumen X7 Industry Tablet
−
The Industry Tablet may not be opened.
Exceptions are the interface cover at the lower side for the installation of the
SIM/Micro SD card or the connection of the Micro USB cable, headset, and power (DC).
−
Do not use, swap or replace and non-specified components.
−
Do not retrofit any components to the internal plugs or slots. One exception is the
SIM card and the Micro SD card.
−
Protect the Industry Tablet from impact!
−
Do not expose the Industry Tablet to caustic/aggressive liquids, vapors, mists!
−
Avoid the impact of moisture outside the specifications.
−
Avoid thermal impact outside the specified temperature range.
−
Use the following data interfaces only outside the potentially explosive atmosphere and exclusively with the devices specified by the manufacturer!
- 1 x 7-pin docking connector (PoGo pin for charging in the docking station)
- 1 x Micro USB Type B (OTG Host, data exchange and charging)
- Interfaces underneath the cover
1 x SIM card
1 x Micro SD card
1 x Micro USB 2.0 Type B (OTG)
1 x Power connection (DC)
1 x Audio combi connection (microphone In/Line Out)
Subject to technical changes.
03/2016
EN 23/61
Commissioning
5.3
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Battery
−
The battery may not be opened.
−
Only charge the battery (type B7-A2Z0-0027) outside the potentially explosive atmosphere.
−
Only use the battery for the purpose listed in this User Manual. Is only suitable for the
Lumen X7, Type B7-A234-2…./……..
−
It is not allowed to remove, change and/or charge the battery inside the potentially explosive atmosphere.
−
There is a danger of burning if used incorrectly. Do not expose the battery to temperatures of more than +60 °C (+140 °F).
−
Defective batteries must be disposed of immediately, whereby the provisions on battery disposal applicable in the respective region must be observed.
−
The battery may explode if it catches fire!
−
Do not short circuit the battery!
Accessories
−
Only install or replace accessories outside the potentially explosive atmosphere.
−
User accessories exclusively which have been tested or certified by BARTEC for this purpose.
−
The end user can replace the battery, SIM card, micro SD card, hand strap, and screen protector himself.
Handling accessories
DANGER
Non certified accessories endanger explosion protection.
Danger to life exists in potentially explosive atmospheres!
Only use original accessories from BARTEC/ Winmate.
Only permitted outside the potentially explosive atmosphere:
Insert/charge battery.
Insert/replace micro SD card.
Insert/replace SIM card.
Attach/remove accessories such as hand strap and screen protector.
5.4 First steps
The individual steps are explained in detail in the following chapters!
Unpack the Lumen X7 Industry Tablet.
Insert SIM card and micro SD card.
Insert battery.
Charge battery.
Switch on/off the Lumen X7 Industry Tablet.
Remove/replace screen protector.
EN 24/61
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
5.4.1
Commissioning
Open/Close protective I/O cover
Open protective I/O cover
Open the protective I/O cover outside of the potentially explosive atmosphere.
1. Place the Industry Tablet on a flat mat.
2. Open carefully the protective I/O cover.
Close the protective I/O cover
1. The protective cover must be correctly aligned, the Inputs/Outputs have to be fully covered.
DANGER
The protective I/O cover has to be closed.
Danger to life exists in potentially explosive atmospheres!
The protective cover must be correctly aligned, the Inputs/Outputs have to be fully covered.
5.4.2 Insert SIM card and Micro SD card
ATTENTION
Damage to the SIM / micro SD card through electrostatic discharges!
Use an antistatic mat.
Ensure that the operator is correctly earthed.
A maximum of 32 GB are supported.
To insert the SIM card and Micro SD card, the protective I/O cover must be removed.
Work steps:
Only insert or replace the SIM / micro SD card outside of the potentially explosive atmosphere.
Only use SIM / micro SD cards which have been tested and certified by BARTEC for this purpose.
1. Place the Industry Tablet on its front (display facing downwards) on a flat mat.
2. Open the protective rubbed bumper.
3. Insert the SIM card (with the golden parts facing up and cut-off corner facing out) and push it in the direction of the arrows as shown in the figure.
4. Push the SD card in the slot to insert it.
Subject to technical changes.
03/2016
EN 25/61
Commissioning
5.4.3
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Insert battery
DANGER
In potentially explosive atmospheres, battery latches must be locked.
Danger to life exists!
Check the locking of the battery latches carefully.
Work steps:
Only install or replace the battery outside the potentially explosive atmosphere.
1. Disconnect any cables connected to the Industry Tablet.
2. Place the Industry Tablet on its front (display facing downwards) on a flat mat.
3. Insert the battery on the connector-pins side (c) first, and then lower the battery (d) into the battery compartment. Continue to hold the battery latches (e) before the battery is fully inserted.
Make sure the battery is completely lowered into the compartment before letting go the battery latches (e). The battery will be flat against the housing once it is fully inserted.
5.4.4 Charge battery
DANGER
Non-certified accessories endanger explosion protection.
Danger to life exists!
Use only the adapter included with the Industry Tablet. Using other adapters may damage the Industry Tablet and the battery.
The Industry Tablet operates either on external adapter or internal battery power. To connect the Industry Tablet to the power supply, the protective I/O cover must be removed.
Work steps:
1. Plug the adapter into the Power Jack of the Industry tablet.
2. Plug the adapter power cable into the electrical outlet. As soon as the adapter is connected with the outlet, the battery will be charged. The battery LED display (see chapter 2.2 "Structure") at the Industry Tablet changes.
EN 26/61
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
5.4.5
LED Status
OFF
Solid red
Solid green
Commissioning
Description
The Industry Tablet is not charging or not properly connected
Low battery
Charging in progress
Turn On and Off the Lumen X7 Industry Tablet
Work steps: Turn the device on
The device may be power supplied either via the adapter or the battery.
1. Press and hold the Power On/Off button (f) for 3 seconds, located on the top of the device.
Do not press the Power On/Off button repeatedly!
Do not perform the following operations until the hard drive indicator turns off:
- Connect or disconnect the adapter
- Press the Power On/Off button
- Touch the tablet buttons, screen, or external keyboard/mouse
Work steps: Turn the device off
Make sure you have closed any programs that are open on the desktop.
1. To turn off the device, press and hold the Power On/Off button (f) on top of the device for 6 seconds or longer until the phone options menu appears.
2. Tap Power off.
The user can also use the Phone options menu to put the device into silent or airplane mode, see features table in chapter 2.2 "Structure".
Subject to technical changes.
03/2016
EN 27/61
Commissioning
5.4.6
5.5
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Remove/replace screen protector
DANGER
Non-certified accessories endanger explosion protection.
A danger to life exists in a potentially explosive atmosphere!
A condition for a safety conscious operation is the use of original screen protectors which have been specified for use by BARTEC.
Using screen protectors from different manufacturers renders the ignition protection useless so that there is a danger of fire or explosion.
Only admissible outside potentially explosive atmospheres:
The screen protector may only be attached or replaced outside the potentially explosive atmosphere!
ATTENTION
Incorrect handling may cause damage to property!
Use a screen protector so as not to impair the device warranty.
Only use screen protector (Type B7-A2Z0-0030) from BARTEC.
Observe the installation instructions for the screen protector.
Do not use any sharp objects to remove the screen protector!
The screen protector can be ordered from BARTEC. The installation instructions for the screen protector forms part of the scope of delivery. Parts number: B7-A2Z0-0030 screen protector, 1 piece.
Screen protector
IECEx-, ATEX- and UL certified
Order number
B7-A2Z0-0030
Work steps:
Only remove or replace the screen protector outside the potentially explosive atmosphere.
1. Lift a corner of the screen protector (g) and remove it from the display.
2. Attach the screen protector in accordance with the "Screen protector installation instructions".
RFID
The internal RFID NFC/HF reader is pre-installed in all devices.
The unique concept permits ultramodern technologies to be combined with each other. It is therefore possible to capture data via RFID technology. The data can be directly processed in the device thanks to virtual keyboards and color display.
The data can be transmitted to other corporate areas for further processing using WLAN,
3.75G, or Bluetooth and are therefore available in real time for further processing.
EN 28/61
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
6. Operation
6.1
6.2
6.2.1
6.2.2
Operation
The operator using an electric system in a potentially explosive environment must keep the accompanying operation equipment in good condition, operate and monitor it correctly and conduct the requisite services and repairs. Before operation the devices it must be checked that all components and documents are available.
Final inspection
The following aspects must be checked before putting the device into operation:
Is there any damage to the display, scanner window (optional) or enclosure?
Is the battery correctly inserted and locked?
Does the screen protector (if used) have the requisite certification?
Is the micro SD card specified for the Lumen X7 Industry Tablet?
Has the SIM card been correctly inserted?
Have only accessory parts been attached to the device which have been released for use in potentially explosive atmospheres?
Care and cleaning
We recommend that the devices be cleaned regularly depending on use and also treated with care to ensure smooth and trouble free operation.
Care
Display
Enclosure
Environment
−
Use screen protector.
−
Use a soft cloth to clean and do not use aggressive cleaners.
− Protect device from impacts.
− Do not expose to extreme loads, e.g. strong knocks and falling from great heights.
−
Do not expose to extreme temperatures.
−
Do not leave in dirty, moist or wet environment.
Cleaning
DANGER
Danger to life exists in potentially explosive atmospheres!
Only clean the devices and the accessories outside of the potentially explosive atmosphere.
Subject to technical changes.
03/2016
EN 29/61
Operation
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
ATTENTION
Devices and accessories can be destroyed if handled incorrectly!
Generally separate the charger from the power supply.
Only clean the interface contacts if the battery has been removed.
There should be no residue, e.g. fluff on the contacts.
There should be no moisture residue on the contacts.
Heed the safety precautions when drying with compressed air.
To guarantee your own safety and the operational safety of the device, observe the precautionary measures carefully.
6.2.3
EN 30/61
Suitable materials for cleaning
−
Alcohol cleaning cloths
−
Lens cleaning cloths
−
Cotton swabs
−
Isopropanol
−
Compressed air spray with tube
Enclosure
−
With alcohol cleaning cloths.
Keys and intermediate spaces
Screen
−
−
With alcohol cleaning cloths.
With alcohol cleaning cloths.
−
Avoid collections of fluid and rub with smooth cloths.
Battery contacts
Interface contacts
Accessories such as charger, docking station, etc.
−
Remove the battery from the device to clean.
− Soak the cotton swabs in an alcohol solution to remove all grease and dirt deposits on the contacts.
−
Repeat cleaning several times.
− Before replacing the battery, the contacts must be completely dry and no fluff should remain.
−
To clean the interface contacts, remove the battery from the device.
−
Soak the cotton swabs in an alcohol solution to remove all grease and dirt deposits on the contacts.
−
Repeat cleaning several times.
−
Before the interfaces of the devices are used again, the interface contacts must be completely dry and no fluff should remain.
−
Separate the accessories from the power supply to clean.
−
Soak the cotton swabs in an alcohol solution to remove all grease and dirt deposits on the contacts.
− Repeat cleaning several times.
−
Before the accessory is reconnected to the power supply, the contacts must be completely dry and no fluff should remain.
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
6.3 Operation, recommendations and requirements
6.3.1
6.3.2
Operation
Basic safety and health protection requirements
Consult your local health and safety officer to ensure that you are acquainted with the safety regulations in your company which serve to protect employees at the workplace.
Ergonomic recommendation
The following recommendations should be considered for everyday work at the workplace:
−
Avoid one-sided, constantly repetitive movements.
−
Body posture should be as neutral as possible.
−
Avoid exercising great force.
−
Keep objects which are used frequently within a functional distance.
−
Adjust the working height to the body height and type of work.
−
Erect objects without vibration.
−
Avoid the exercising of direct pressure.
−
Ensure that the tables and chairs are adjustable.
−
There must be sufficient room for body movements.
−
Ensure that the working environment is suitable.
−
Optimise work flows.
−
Alternate between the left and right hand as frequently as possible when conducting repetitive tasks.
6.3.3 Vehicle installation
It is not permitted to connect a warning device which leads to horn sounds or light signals when receiving a call in road traffic.
Information on conducting telephone conversations only applies if a 3.75G module is used.
RF signals may impair incorrectly installed or inadequately shielded electronic systems in vehicles (including safety systems). If you have any questions on your vehicle, get in touch with the manufacturer or sales person.
You can also learn from the manufacturer whether additional equipment has been fitted to the vehicle. An airbag has a strong impact. Do NOT place objects, such as installed or portable radio equipment, in the area above the airbag or in the area of deployment of the airbag. If radio equipment was not correctly installed in the vehicle, severe injuries may result if the airbag is triggered.
Position the device within good range. Ensure that you have access to the device without having to take your eye off the road.
Subject to technical changes.
03/2016
EN 31/61
Operation
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Road traffic safety
Do not take any notes and do not use the device when driving. Making a list of to-dos or browsing through the address book when driving has a negative effect on safe driving.
When driving on the road, you must primarily think of your safety and that of other road users. You should therefore concentrate completely on the road. Check the legal provisions on the use of wireless devices in road traffic of the respective region. Always observe these.
If you use a wireless device during driving a car, rely on your good judgement and remember the following:
−
Become acquainted with the wireless device and its functions such as the shortcut dialling or dial repetition function. These functions may prove to be useful if you would like to make calls without taking your eye off the road.
−
Where possible, use hands-free equipment.
−
Let your dialogue partner know that you are behind the steering wheel. When necessary discontinue the call in dense traffic or poor weather conditions. Rain, sleet, snow, ice and even very dense traffic represent dangers.
−
Dial the required numbers carefully and estimate and the traffic situation. Make your calls once you have brought your car to a stop or before you leave. Plan your calls such that these can be done when parked. If you really must make a call during the trip, only dial a part of the number, check the road and look in the rear view mirror and then dial the rest of the number.
−
Do not succumb to stressful and emotional telephone conversations which could take your attention from the road. Let your dialogue partner know that you are in a car and refrain from conversations which could take your attention from the road.
−
Call for help using your mobile device if necessary. Dial the emergency services (911 in the USA and 112 in Europe) or other local emergency service numbers in the event of fire, accident or medical emergencies. Remember that these calls are free of charge on the wireless device! The call can be made independently of security code or networks with or without a SIM card.
−
Help your fellow humans in emergency situations with your mobile device. If you witness a serious accident, crime or any other emergency, call the emergency service (911 in the USA and 112 in Europe) or another local emergency service number because you could be the one who needs help next time.
−
Call the breakdown service or a special mobile radio number for support if you encounter problems on the road. If you pass a car with a breakdown, which does not represent a serious impediment to traffic, pass traffic lights which do not function, a traffic accident with slight damage and without injuries or a possibly stolen car, please get in touch with the road police or another special mobile radio number for support.
EN 32/61
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Operation
The “Mobile Communication Industry” requests you to give safety priority when using your device/telephone.
6.3.4
6.3.4.1
6.3.4.2
6.3.4.3
6.3.4.4
6.3.4.5
Information on the use of wireless devices
Heed all warnings referring to the use of wireless devices.
Safety in aircraft
Switch off the wireless device when asked to do so by the ground staff and by employees of the airline. If your device has a flight mode or similar function, find out about its correct use with the help of the aircraft staff.
Safety in hospitals
Wireless devices emit radio frequencies and cause disturbances to medical technical electrical devices. Wireless devices should be switched-off on request when you are in hospitals, clinics or health establishments. This is intended to avoid any possible interferences with sensitive medical equipment.
Heart pacemakers
Manufacturers recommend that a minimum distance of 15 cm be observed between a wireless handheld device and a pacemaker to avoid potential interference. This guideline is in line with the independent research results and recommendations of Wireless
Technology Research.
−
Persons with heart pacemakers should ALWAYS keep at least 15 cm away from the activated device.
− The device may not be worn by these persons in the breast pocket.
− The device should be held to the ear which is further away from the heart pacemaker.
− If you have reason to assume that an interference has arisen you should SWITCH-
OFF the device immediately.
Hearing aids
The wireless device may cause disturbances to hearing devices. Get in contact with the manufacturer of your hearing device in the case of disturbances to ask about possible solutions.
−
The device should be held to the ear which is furthest away from the heart pacemaker.
− If you have reason to assume that interference has arisen you should SWITCH OFF the device immediately.
Other medical equipment
Ask your doctor or the manufacturer of the medical device to determine whether putting the wireless product into operation impairs the medical device.
Subject to technical changes.
03/2016
EN 33/61
Operation
6.3.5
6.3.6
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
LED devices
CAUTION
LED light! May damage eyesight!
If you use LED for the camera flash, keep the camera flash LED at least 317 mm
(12.5 inch) away from a person’s eyes. Otherwise serious damage may be caused to the eyes.
Devices from BARTEC/Winmate equipped with LED devices comply with the following guidelines:
−
IEC 62471:2006-07 for LED safety.
Restrictions in the case of wireless devices
The use of wireless devices is possibly forbidden or restricted. This applies primarily on board aircraft, in hospitals, in the vicinity of explosive substances or under other hazardous conditions. If you are not sure which regulations apply to the use of the device, ask permission before switching it on.
Radio modules
The device contains radio modules. The identification data for these modules are provided below:
− Radio module from BARTEC/Winmate which supports WLAN 802.11 a/b/g/n and
Bluetooth.
−
ARM® Cortex™-A7 Quad Core 1.5 GHz (WLAN-WiFi IEEE 802.11 a/b/g/n, Bluetooth
Version 3.0 + EDR, GPS, WWAN 3.75G - GSM / GPRS / EDGE / WCDMA / HSDPA /
HSUPA).
Bluetooth® radio technology
This is an authorised Bluetooth® product. Further information and an end product list is provided at
https://www.bluetooth.org/tpg/listings.cfm
.
Country-specific roaming
This device has the International Roaming function (IEEE802.11d) which ensures that the device is used on the channels prescribed for the respective country.
Ad-hoc operation
The ad-hoc operation is restricted to the channels 36–48 (5150–5250 MHz). The use of this bandwidth is restricted to indoor areas; use outdoors is not permitted.
EN 34/61
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
6.4
Operation
Operating frequency - FCC and IC
5 GHz only
Use in the UNII-Band 1 (Unlicensed National Information Infrastructure) in the range of
5150-5250 MHz is restricted to indoor rooms. The failure to heed this rule leads to the illegal operation of the device.
Industrial standard declaration for Canada
ATTENTION
Devices can be damaged by inappropriate handling!
The device for the frequency range 5150-5250 MHz is exclusively intended for operation in indoor rooms in order to restrict possible co-channel interference for satellite mobile radio systmes to a minimum. The frequency ranges 5250-5350
MHz and 5650-5850 MHz are primarily intended for the high power radar devices
(i.e. these radar devices take priority). These radar devices may cause interference and/or damage WLAN devices.
2.4 GHz only
In the USA the channels 1 to 11 are available for the 802.11 b/g operation. The range of channels is restricted by the firmware.
FCC requirements to protect against high-frequency interference
Subject to technical changes.
03/2016
This device has been tested and satisfies the limit values for a digital device of Class B according to Part 15 of the FCC Guideline. These limit values were stipulated to guarantee appropriate protection against disturbances if the device is used in residential areas.
The device generates and uses radio frequency energy and may emit this energy. This can have a disturbing effect on other radio frequencies if the device is not connected and used in accordance with the operating instructions. A guarantee that no interference will arise for a certain installation cannot be given.
If the device causes interference to the radio or TV reception which can be recognised by switching the device on and off, the interference should be eliminated by one or several of the following measures:
− Re-alignment or moving of the receiving aerial.
− Enlarging the distance between device and receiver.
− Connecting the device to a different socket than the one to which the receiver is connected.
−
Advice from the dealer or a radio/television technician.
EN 35/61
Operation
EN 36/61
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Declaration in accordance with the FCC regulations, Part 15.21
Changes which have not been explicitly approved by the party responsible for compliance with the regulations can lead to the expiry of the operating authorization for this device.
Radio transmission devices (Part 15)
This device satisfies the requirements of Part 15 of the FCC Guidelines. The operation of the device is based on the following two conditions:
−
The device may not cause any damaging interference.
−
The device must absorb all receiving interference including interference which may lead to undesirable operation.
Requirements placed on the protection from high frequency interference - Canada
This digital device of Class B satisfies the Guidelines of the Canadian standard ICES-003.
Radio transmission devices
This device corresponds to RSS 210 (Industry & Science Canada). The operation of the device is based on the following two conditions:
−
The device may not cause any damaging interference.
−
The device must absorb all receiving interference including interference which may lead to undesirable operation.
Label symbol: “IC:” before the radio certification means that the technical data of Industry
Canada have been satisfied.
Country approvals
For 2.4 GHz products: Europe covers Belgium, Bulgaria, Denmark, Germany,
Estonia, Finland, France, Greece, Great Britain, Ireland, Iceland, Italy, Latvia,
Liechtenstein, Lithuania, Luxembourg, Malta, Netherlands, Norway, Austria, Poland,
Portugal, Romania, Sweden, Switzerland, Slovakia, Slovenia, Spain, Czech Republic,
Hungary and Cyprus.
Test symbols are attached to the device which shows that the radio modules are approved for use in the following countries: USA, Canada and Europe.
Detailed information on the test symbol for other countries is provided in the EC declaration of conformity.
USA
WARNING
It is not permitted to operate the device without official approval.
Acquire a permission from the authorities first.
The channels 1 to 11 are available in the USA for 802.11 b/g operation. The range of the channels is restricted by the firmware.
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Operation
Radio transmitters for RLAN devices
The operation of RLAN devices (5 GHz) is subject to the following restrictions in Canada:
−
Frequency range restricted to 5.60 GHz to 5.65 GHz.
This device complies with the radio standard RSS 210 of the Industry & Science Canada.
The operation of the device is based on the following two conditions:
−
The device may not cause any damaging interference.
−
The device must absorb all receiving interference including interference which may lead to undesirable operation.
Label symbol “IC:” before the radio certification merely means that the technical data of
Industry Canada have been satisfied.
6.5 Electromagnetic fields
Reduction in high frequency energy – intended use
Only use device in compliance with the supplied instructions.
International
The device complies with the internationally recognised standards for the recommended maximum values for electromagnetic fields of radio devices. Information on
“internationally“ recommended maximum values for electromagnetic fields is provided in
BARTEC’s Declaration of Conformity at
http://www.bartec.de/
.
Europe
Portable devices have been specially tested for operation in direct body proximity. Use exclusively belt clips, holsters and similar accessories which have been tested and approved by BARTEC to ensure compliance with the EU regulations.
USA and Canada
Declaration on joint use
To comply with the FCC guidelines with respect to exposure to high frequency energy, the aerial for this transmitter should not be used in the direct vicinity of, or in an operation unit with, other transmitters/aerials with the exception of those approved in this document.
Subject to technical changes.
03/2016
The Lumen X7 Industry Tablet should only be worn close to the body when turned off.
Portable devices have been specially tested for operation in direct body proximity. Use exclusively belt clips, holsters and similar accessories which have been tested and approved by BARTEC to ensure compliance with the FCC regulations. Belt clips, holsters and similar accessories of third manufacturers may not satisfy the FCC requirements for the recommended maximum values for electromagnetic fields and should not therefore be used.
Micro SD card
The Micro SD card slot provides a secondary, non-volatile memory. The slot is located on the side of the Industry Tablet. Further information is provided in the documentation supplied with the card. Observe the manufacturer’s recommendations on use.
EN 37/61
Operation
6.6
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Use the Android 4.2 Operating System
6.6.1 Wake up the phone
If you do not use the phone for a while, the screen dims and then darkens to conserve the battery.
Work steps:
1. Press the Power on/off button (a) on the top of the Industry Tablet.
2. Drag the lock symbol (arrow) to the right.
There are several options to choose the screen lock method such as: Slide, Voice
Lock, Pattern, PIN, or Password.
3. To select the screen lock method, tap select Settings and then select Security.
EN 38/61
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
6.6.2
6.6.3
Operation
Use the touch screen
Tap
Tap and hold
Drag
Slide
Double tap
Zoom out/ zoom in
Simply touch the icon, symbol, or onscreen button using your finger.
Touch an item using your finger and not lifting it until an action occurs.
Touch and hold an item for some amount of time and then, without lifting your finger, move your finger along the screen until you reach target position.
Quickly move your finger across the surface of the screen, without pausing it when you first touch it. (e.g. scroll a page or a list up or down).
Tap quickly twice on a webpage, map, or other screen to zoom.
Double tapping after pinching the zoom in some application to fit the width of the screen.
Place two fingers on the screen at once and pinching them together (to zoom out) and spreading them apart (to zoom in).
Orientation of the screens rotates with the phone as user turn it from upright to its side and back again.
Rotate the screen
Use the Home screen
The home screen is the starting point to access all the features on the Industry Tablet. It displays application icons, widgets, shortcuts, and other features. The user can personalize the home screen. See "Personalize the home screen".
Subject to technical changes.
03/2016
2
3
4
Position Designation
1 Status Bar
Launcher icon
Apps
Settings
Description
Shows the time, signal strength, battery status, and other information. It also displays notification icons.
Opens the launcher and view all applications.
Applications that the user can use directly on the home screen.
General settings that concern the Industry
Tablet.
EN 39/61
Operation
6.6.4
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Personalize the home screen
The user can add application icons, shortcuts, widgets, and other items to any part of the
Home screen where there is free space. The user can also change the wallpaper.
Change the wallpaper
Work steps:
1. Tap and select Settings, select Display and then tap Wallpaper.
2. On the menu that opens tap the type of item you want to add.
Move an item
Work steps:
1. Tap and hold the item you want to move, until it can be moved.
2. Drag the element to a new location on the screen.
3. Place the element where you want to put it and release your finger. (Example: To move the Clock to the home screen.)
EN 40/61
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Remove an item
Work steps:
1. Tap and hold the element (a) you want to remove (here the clock item).
The launcher icon (b) will change into a Remove icon.
Operation
Subject to technical changes.
03/2016
2. Drag the item you want to remove to the Remove icon.
When the item turns red, release yout finger.
The element you want to remove is removed.
View other elements on the home screen
Extensions to the home screen provide extra space for APPS, shortcuts, and other items.
Work steps:
1. Slide your finger left or right across the home screen.
2. Tap the launcher icon to show the entire APPS and Widgets of the device.
APPS
WIDGETS
EN 41/61
Operation
EN 42/61
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Status and notification icons
The status bar appears at the top of every screen. On the left are notification icons (d) and on the right are status icons (e), along with the current time.
Notification icons
The following icons indicate that you have received notification.
New email message
New text or multimedia message
Incoming call
Missed call
Speakerphone is activated Alarm is set
Upcoming event
Data is syncing
Problem with sign-in or sync
Phone microphone is muted
Downloading data
Phone is connected via USB cable
A screenshot is captured
Status icons The following icons indicate the status of the Industry Tablet, for example if users are connected to a Wi-Fi network that is not connected to the internet, the network icons are appears in white color.
Connected to GPRS mobile network
Bluetooth is on
Connected to 1xRTT mobile network
Connected to EDGE mobile network
Connected to 3G mobile network
Conneted to a Bluetooth device
No SIM card installed
Vibration mode
Ringer is silenced
Mobile network signal strength
Searching for a network signal
Battery is very low
Battery is low
No signal
Connected to a Wi-Fi network
Roaming
Battery is partially drained
Battery is full
Airplane mode
Battery is charging
Receive location data from
GPS
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
6.6.5
Operation
Use the On-Screen Keyboard
The user will be able to enter text using the On-Screen Keyboard. Some applications will launch the keyboard automatically. In others, the user needs to touch a text field where the user wants to enter text to launch the keyboard.
Enter text by typing
Work steps:
Open a text field (in this example we used Google Chrome to create a note).
The On-Screen Keyboard opens.
6.6.6 Edit text
Tap (e) once to capitalize the alphabet.
If the user taps in a text field which already contains text, the insertion point is set where the user taps and the cursor appears. The user can drag the cursor to pick exactly where you want to add more text. The user can also select a word to copy, cut and paste it. See "Edit text".
Tap the delete key to erase characters to the left of the cursor.
Tap the key to enter numbers.
Tap the key to return to letters.
To open a small window with a set of common symbols, tap and hold the periode key. Slide your finger up to the list of the options.
Lift your finger when you find your selection. The selected symbol will be inserted.
Work steps:Select text
1. Double tap the text you want to select.
2. Tap Select All to select all the sentences in the menu that appear.
The selected text is highlighted in blue, with a tab at each end of the selected word.
Subject to technical changes.
03/2016
EN 43/61
Operation
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
3. Drag the selection tab to expand or reduce the range of the selected text.
Work steps: Cut or copy text
Select the text that should be cut or copied and then should be pasted.
Tap on the key to remove the selected text from the text field. The removed text is stored in a temporary area so that you can paste it into a different text field.
Tap on the key to copy the selected text from the text field. The copied text is stored in a temporary area so that you can paste it into a different text field.
Work steps: Paste text
1. Place the cursor in the text field where you want to paste the text. The user can paste text that you copied from one application into a text field in any application
2. Tap and hold into the location that you want to paste the text. Tap Paste in the menu that opens to replace the text with the cut or copied text.
6.6.7 Set the display
Use the display settings to configure brightness and other screen settings.
Configure brightness
For the longest battery life between charges, use the lowest brightness level.
EN 44/61
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Operation
Work steps:
1. Tap and then tap Settings.
2. Tap Display and then tap Brightness. The following options for Brightness will be offered:
Automatic
Brightness
Tap Automatic Brightness to adjust the brightness automatically
Economical
Backlight
Slide bar
Tap Economical Backlight to save power.
Slide the bar to adjust the brightness manually.
Configure Font size
Work steps:
1. Tap and then tap Settings.
2. Tap Display and then tap Font size. There are several options for Font Size: Small,
Normal , Large, or Huge.
6.6.8
6.6.9
Set the audio profile
Use the sound settings to configure how and at what volume the phone rings, vibrates or alerts the user in other ways when the user receives a call, receives a notification, or an alarm sounds.
Work steps:
1. Tap and select Settings and then tap Audio profiles.
2. Tap General and then tap Settings (located on the right side of the screen).
The user can select to disable or adjust music, video games and other media as well as notifications and alarms. The following options will be offered:
General
Ring
Silent
Meeting
Outdoor
Silent only
Vibrate only
Loudest ring and vibrate
Adjust volume
Work steps:
Press the volume keys on the side of the Industry Tablet to change the ring volume
(On Home screen) or earpiece volume (during a call).
Subject to technical changes.
03/2016
EN 45/61
Operation
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
6.6.10 Set language and keyboard
Use the language and keyboard settings to select the language for the text on your
Industry Tablet and for configuring the On-Screen Keyboard, including words that you add to its dictionary.
Set language
Work steps:
1. Tap and then tap Settings.
2. Tap Language & Input and then Language to open the language screen, where user can select the language to use for the text on the device.
EN 46/61
Language
Spell checker
Personal dictionary
Opens the language screen, where the user can select the language to use for the text on the device.
Improves the text input experience on
Android by helping the user to identify and correct spelling errors quickly.
Adds custom words to a personal dictionary for faster typing.
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Operation
Change the keyboard language
The current keyboard language is displayed on the space key and the user can switch languages.
Work steps:
Tap the keyboard icon located on the top right.
There are four input options:
Hardware-physical keyboard
English (US) - Android
Keyboard
Google voice typing
Tap Hardware-physical keyboard to use the Hardware-physical keyboard.
Tap English (US) - Android Keyboard to use the Android Keyboard.
Tap Settings (on the display's right) to change the input language via Input
languages >> ACTIVE INPUT METHODS.
Make the required settings in General by tapping (for example autocapitalization, auto-correction, or other options).
Tap Google voice typing to control the
Industry Tablet via speech.
Subject to technical changes.
03/2016
EN 47/61
Operation
6.6.11
6.6.12
6.6.13
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
USB debugging setting
To permit debugging tools on a computer to communicate with the user’s Industry Tablet via USB connection.
Work steps
1. Tap and then tap System settings.
2. Tap { } Developer options and then tap USB debugging to allow USB debugging.
If the USB is connected, there will be a symbol in the notification icons on the bottom right.
About the phone
About Phone includes information about user’s Industry Tablet.
System Update
Provides information regarding the local or online update of your devices.
Status
Legal Information
Opens the status screen with a list of information about battery, network, signal strength, and other details.
Lists details about the model number, Android
Version, Baseband version etc. This information is useful if the user needs to work with the support team.
Screenshot capture
Screenshot capture is result of simultaneous oppress of volume key (-) and On-/Off key.
The screenshots stored on the device: Phone Storage / Pictures / Screenshots
Volume key (-) On-/Off key
EN 48/61
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
6.7
Operation
Connection to mobile networks and devices
When users assemble their Industry Tablet with a SIM card from the service provider, their phone is configured to use their provider networks for voice calls and for transmitting data.
Different locations may have different mobile networks available. The user may need to configure the Industry Tablet to use certain networks. To obtain fastest networks, the user can configure the Industry Tablet to 3.75G. To extend the life of battery the user can use
2G network.
6.7.1 Check the network (3G) connection
Work steps:
1. Tap and then tap Settings.
2. Tap More… in the Wireless & networks, and then tap Mobile networks.
3. Tap Network operators to select the network operator.
Do not change the parameters of the access point to prevent the user to be unable to access network sources.
6.7.2 Turn on the data service
Work steps:
1. Tap and then tap Settings.
2. Tap More… in the Wireless & networks, and then tap Mobile networks.
3. Tap Data enabled to enable the data connection via mobile network.
Subject to technical changes.
03/2016
4. Select the desired network operator to enable the data connection.
EN 49/61
Operation
6.7.3
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Connect to Wi-Fi networks
Turn on the Wi-Fi and connect to a Wi-Fi network
Work steps:
1. Tap and then tap Settings.
2. Tap Wireless & networks and then select Wi-Fi to turn it on.
3. Tap Wi-Fi.
The device scans for available Wi-Fi networks and displays the list of it. Secured networks are indicated with a lock icon .
If the phone finds a network that you have connected previously, it connects to it automatically.
4. Tap a network to connect to it.
If the network is open, you are prompted to confirm that you want to connect it by tapping Connect.
If the network is secured, users are prompted to enter a password or other credentials.
To check the details about the speed, security, address, and related settings, tap its name in the Wi-Fi settings screen.
EN 50/61
Work steps: Add a Wi-Fi Network
1. Turn on Wi-Fi, in the Wi-Fi settings screen, tap on the icon (at the top right over the list of the recognized networks).
The Add network window is displayed.
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Operation
6.8
6.8.1
6.8.2
2. Input the Network SSID (name of the network) (a).
3. If the network is secured, tap the security menu (b) and then tap the type of security deployed on the network. Enter any required security credentials.
4. Tap Save (c).
Connection to Bluetooth devices
Turn Bluetooth on or off
Work steps:
1. Tap and then tap Settings.
2. Tap Wireless & networks and the select Bluetooth to activate the Bluetooth function.
Connect / disconnect to Bluetooth devices
Connect
Work steps:
1. Tap and then tap Settings.
2. Tap Wireless & networks and then tap Bluetooth. The Industry Tablet will automatically scan and display the IDs of all available Bluetooth devices in range.
3. Tap Search for devices to search for other Bluetooth devices.
4. Tap the ID of the other device in the list in Settings to pair them.
Subject to technical changes.
03/2016
Work steps: Disconnect
1. Tap the device in the Bluetooth settings screen.
2. Tap OK to confirm that you want to disconnect.
EN 51/61
Operation
6.9
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Connection / disconnection via USB
DANGER
Non certified accessories endanger explosion protection.
Danger to life exists in potentially explosive atmospheres!
The external Micro USB Type B interface (OTG Host, data exchange, and charging) must only be used outside hazardous areas with specified accessories recommended by the manufacturer.
ATTENTION
Data loss due to incorrect connection/disconnection of USB devices!
When connecting your Industry Tablet to a computer and mounting its USB storage or SD card, the user must follow the computer’s instructions for connecting and disconnecting USB device, to avoid damaging or corrupting files.
The user can connect the Industry Tablet to a computer with an USB cable to transfer files between the Industry Tablet and another computer.
Connect Lumen X7
Work steps:
1. Use the USB cable that came with your Industry Tablet to connect the phone to a
USB port on your computer.
2. After you received a notification that the USB is connected, tap the notification panel and then tap (USB) connected as a media device.
EN 52/61
3. Select Media device (MTP) to confirm the file transfer.
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Operation
When the device is connected as USB storage, the screen indicates that USB storage is in use and user will receive a notification.
Subject to technical changes.
03/2016
Disconnect Lumen X7
Work steps:
1. Tap the notification panel and then tap USB connected.
2. Tap Turn off USB storage in the screen that opens.
3. Disconnect the Industry tablet by unplugging the USB cable.
EN 53/61
Operation
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
6.10 Use the camera
The Industry Tablet is equipped with a 5 MP camera on the rear side, which the user can use to capture photos or video.
Make sure that the protective lens cover is clean before taking pictures. A dirty lens cover can cause blurry pictures.
6.10.1
6.10.2
Open the camera
Work steps:
Tap the Launcher and then tap Camera . The camera opens in portrait mode, ready to take a picture or to shoot a video.
Take a picture
Work steps:
1. Adjust the exposure, flash, and other necessary settings. Or leave it automatic.
2. Das gewünschte Objekt auf dem Bildschirm einrahmen und zum Vergrößern oder
Verkleinern aufziehen bzw. zusammenschieben.Frame your subject / object on screen.
Tap the On Screen Shutter icon.
The camera brings the image into focus. When the image is in focus, the focus indicators in each corner will turn green. The camera is ready to capture.
Touch the icon to change camera settings.
View pictures
After taking a photo, a thumbnail of the picture is shown on the corner of the capture screen.
Work steps:
Tap the thumbnail to view the picture. The following options are available:
Share photo
Delete photo
View another photo in the gallery.
EN 54/61
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
6.10.3 Record a video
Operation
Work steps:
1. Tap to switch from camera to video mode.
2. Point the lens to record the scene where you want to start.
3. Tap the Record icon to start the video recording.
The countdown time remaining to record the video is located on the upper left. When the time left is less than a minute, the countdown turns red.
4. Tap the Record icon to stopp the video recording.
6.10.4 Open the galery
Work steps:
1. Tap the Launcher and then tap Gallery .
2. Tap a folder to view the pictures or video inside in full screen mode.
3. Slide the pictures to the right or left to view the previous or next picture.
6.11 Use RFID NFC/HF
6.11.1 Enable RFID HF/NFC
1. Enter the “Settings“ menu with a tab on the setting symbol. (Picture 1)
2. Select the option “More“ to open the menu for “Wireless & Networks“. (Picture 2)
3. Enable NFC option to “ON“. (Picture 3)
4.
Subject to technical changes.
03/2016
Picture 1 Picture 2 Picture 3
EN 55/61
Operation
6.11.2
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Daten mit Punkt zu Punkt (P2P) Verbindung übertragen
1. There are two NFC capable devices required.
2. Enable NFC on the receiver device.
3. Enable NFC function on Lumen X7 as described in chapter 6.11.1.
4. Select the program or file what you transmit.
5. Bring both NFC devices close together that connection can established.
6. If connection is established then you can transmit the file with a tab on the message
“Touch to beam“
7. Confirm the message box with “Yes”.
8. Check on the receiver device that the file is received.
Example:
Example 1: Google Maps
Example 2: Internet URL Adresse
EN 56/61
Subject to technical changes.
03/2016
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Example 3: Kontaktdaten
Operation
6.11.3 Use Read / Write Function
The RFID HF/NFC Reader supports following protocols:
−
ISO 14443-A (read)
−
ISO 14443-B (read)
−
ISO 15693 (read)
−
ISO 18092 (read/write)
By default, no application for read / write function is pre-installed.
The user can download an existing application from Google App Store what is usable for the RFID HF/NFC reader.
Another option is to use the standard Google Android SDK (Software Development Kit) for development of a customized solution. For the Lumen X7 is a SDK available for download what is needed for the development. See Chapter 12.1
Example Application for test:
Open Google App Store and search for “NXP” and install it.
Subject to technical changes.
03/2016
EN 57/61
Faults and troubleshooting
7” Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
7. Faults and Troubleshouting
7.1
EN 58/61
DANGER
Danger to life exists in potentially explosive atmospheres!
Examine defective devices and any accessories only outside the potentially explosive atmosphere.
Troubleshooting
Problem
The battery does not charge.
Solution
- Check that the external power supply is connected and that the replaceable battery is inserted correctly.
There is no WLAN signal.
The WLAN signal is very poor.
Bluetooth connection to other devices is not working.
The GPS application cannot find my position.
There is no sound from the loudspeaker.
power button to wake up the device.
- The settings for the background lighting are possibly too low. Increase the settings of the background lighting.
- Check under "System settings/Wireless & networks" whether the WLAN is activated.
- If the function is deactivated, activate the function. If the Industry Tablet finds a network that you have connected previously, it connects to it automatically.
- Select a network with a better signal strength.
- Check that the Bluetooth is switched on in both devices.
- Check whether the two devices are connectable.
- •Check whether the two devices are compatible with one another
- Check whether the two devices are further than
10 m apart.
- Check under "System settings/Wireless & networks" whether the GPS is activated.
- You may possibly be outside the GPS range. Take the Industry Tablet outdoors or closer to a window.
- Check whether the objects in the environment generate faults such as microwaves or mobile telephones.
- Move the Industry Tablet away from such devices.
- Check the volume setting with the buttons for high and low.
- When using external audio devices check whether the cable has been connected correctly.
- Check that a Lumen X7 with integrated RFID
Reader is used.
The RFID reader does not work.
Subject to technical changes.
03/2016
7” Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
8. Service, Inspection, Repair
8.1
8.2
8.3
8.3.1
Disposal
Service, inspection, and repair of Lumen X7 Industry Tablets may be conducted exclusively by trained and qualified staff! The staff who is familiar with the service, inspection, and repair of Lumen X7 Industry Tablets, has been informed about the risks and has the qualifications necessary for this work.
Service intervalls
DANGER
Prevent electrostatic charging in potentially explosive atmospheres.
Danger to life in explosive atmosphere!
Do not dry wipe or clean devices.
The mechanical state of the Industry Tablet should be regularly checked. The service intervals will depend on the ambient conditions. We recommend that a service be conducted at least once a year. Regular servicing is not necessary if the Industry Tablet is correctly operated in accordance with the installation instructions and under appropriate consideration of the ambient conditions.
Inspection
According to EN/IEC 60079-17 and EN/IEC 60079-19, the owner/operator of electrical plants in potentially explosive atmospheres is obliged to have these plants checked by an electrician to ensure that they are in a correct condition.
Service and repair work
In addition to Directive 99/92/EC, the standards EN/IEC 60079-17 and EN/IEC 60079-19 also apply to the servicing and repair as well as the testing of accompanying operating devices.
Work connected with assembly/dismantling, operation and servicing may only be conducted by trained specialists. All statutory requirements and other binding guidelines on occupational health and safety, accident prevention and environmental protection must be observed.
Information on sending in for repairs
The following information is required for the repair:
- Serial number of the device, see label for series number in chapter 3.6 "Product labelling"
- Model number or product name, see type plate in chapter 3.6 "Product labelling"
- Software type and version number, see system information in Control Panel
Subject to technical changes.
03/2016
EN 59/61
Repair, Disposal,
Packaging Information
9. Disposal
7" Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
Please read through the handling guidelines for the RMA process before you send in a defective device for repair. Then complete the RMA form (Return Merchandise
Authorization), sign it and send it to our "Returns Centre".
E-Mail:
Fax:
+49 7931 597-119
We cannot guarantee the processing within the contractually agreed period for any returns received by us without RMA number.
The handling guidelines and the RMA form are available for download from our website:
http://www.bartec.de
If you have any questions? Please write us a mail or give us a call.
E-Mail: [email protected]
Telephone: +49 7931 597-444
The Lumen X7 Industry Tablets contain metallic and plastic parts and electronic components.
As professional electrical devices, our devices are intended exclusively for commercial use, so-called B2B devices, in accordance with the WEEE Directive.
The WEEE Directive provides the framework for the treatment of old electrical equipment throughout Europe. This means that you may not dispose of these devices in usual household waste but must dispose of them separately in an environmentally compatible manner and can also bring them to the collection points of public disposal companies.
All products purchased from us can be returned to us by our customers for disposal.
We will ensure disposal in accordance with the applicable laws.
The sender shall bear the costs of postage and packaging.
10. Forwarding and Packaging Information
ATTENTION
Sensitive devices! Damage may be caused by incorrect packaging!
Use original packaging for transport.
EN 60/61
Subject to technical changes.
03/2016
7” Industry Tablet - Lumen X7
Type B7-A23.-2…/……..
11. Accessories
Accessories and
Additional Information
Description
Ex-certified accessories
Spare battery
Lithium polymer battery 3.7 V / 5.300 mAh
Screen protector
Protect the touchscreen from dirt and water
Micro SD card
• storage capacity of 4 GB
• storage capacity of 8 GB
Hand strap
For a safe handling during use of the device
Capacitive Stylus
For direct entry via touchscreen
Optional accessories for the non-Ex area
USB power adapter
Input: AC 100-240 V / 50-60 Hz / 0.3 A
Output: DC 5 V / 3 A / 15 W max.
- with EU-plug, with US-plug
USB cable
Type A to micro Type B
USB car charger cable
Desk Docking Station
- 4 x USB 2.0 (2 x rear, 2 x side), LAN (10/100),
- COM (RS232), 12V DC IN
Vehicle Docking Station
- 4 x USB 2.0, LAN (10/100), COM (RS232),
12V up to 36V DC IN
Quick Start Guide
12. Additional Information
12.1 Links
Order number
B7-A2Z0-0027
B7-A2Z0-0030
17-28BE-F006/000A
17-28BE-F006/000B
03-9849-0141
03-9849-0144
03-9914-0013
03-9919-0025
03-9914-0012
03-9915-0020
03-9915-0021
B1-A234-7E0001
All original Winmate documents refer to the non-explosion-protected version.
Please heed the safety information in the BARTEC manuals when using original
Winmate documents.
The explosion-protected Lumen X7 series from BARTEC and the non-explosionprotected Winmate E430RM4 series do not differ in terms of software.
The available software in the Winmate download center runs on all devices.
http://www.bartec-group.com
BARTEC website
http://www.bartec.de/automation-download/
BARTEC download page
Subject to technical changes.
03/2016
EN 61/61
Your partner for safety technology.
Challenge us!
BARTEC
GmbH
Germany
Max-Eyth-Str. 16
97980 Bad Mergentheim
Phone: +49 7931 597-0
Fax: +49 7931 597-119 [email protected]
www.bartec.de
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement