NuPoint Unified Messaging User Guide

NuPoint Unified Messaging User Guide
NuPoint Unified Messaging
User Guide
RELEASE 8.3
NOTICE
The information contained in this document is believed to be accurate in all respects but is not warranted
by Mitel Networks™ Corporation (MITEL®). The information is subject to change without notice and should
not be construed in any way as a commitment by Mitel or any of its affiliates or subsidiaries. Mitel and its
affiliates and subsidiaries assume no responsibility for any errors or omissions in this document. Revisions
of this document or new editions of it may be issued to incorporate such changes.
No part of this document can be reproduced or transmitted in any form or by any means - electronic or
mechanical - for any purpose without written permission from Mitel Networks Corporation.
Trademarks
The trademarks, service marks, logos and graphics (collectively "Trademarks") appearing on Mitel's
Internet sites or in its publications are registered and unregistered trademarks of Mitel Networks
Corporation (MNC) or its subsidiaries (collectively "Mitel") or others. Use of the Trademarks is prohibited
without the express consent from Mitel. Please contact our legal department at legal@mitel.com for
additional information. For a list of the worldwide Mitel Networks Corporation registered trademarks, please
refer to the website: http://www.mitel.com/trademarks.
Other product names mentioned in this document may be trademarks of their respective companies and
are hereby acknowledged.
Mitel® NuPoint Unified Messaging™
User Guide
Release 8.3
January 2017
®,™ Trademark of Mitel Networks Corporation
© Copyright 2017, Mitel Networks Corporation
All rights reserved
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
About Your Voice Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
About This Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Your Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Preparing to Access Your Mailbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Accessing Your Mailbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Inside Your Company . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
From Your Own Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
From Another Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Outside Your Company . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
From an Outside Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
From a Outside Line to the Automated Receptionist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Setting Up Your Mailbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Menu Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Greetings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Passcode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Playing Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Accessing the Voice Mail and Email Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Playing Your Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
While Listening to a Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
When You Have Finished Listening to a Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Making Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Making a Voice Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Recording a voice message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Sending a Message when You Have Finished Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
User Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Accessing User Options and User Tutorial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Greetings, Name and Passcode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Distribution Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Creating or Modifying a Distribution List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Using a Distribution List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Call Schedule Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
NuPoint WakeUp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Pager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Message Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
iii
Document Title - Using Variables
Future Delivery Audit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Record-A-Call Optional Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Recording while on a Two-Party Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Recording Using Softkeys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Recording Using Hard Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Placing a Call On Hold While Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Listening to a Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Fax Optional Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Fax Delivery Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Playing and Printing Fax Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
From a Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
From a Fax Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
When You Have Finished Listening to a Fax Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Making a Fax Message (Without Voice) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
From Your Company Fax System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
From Your Own Mailbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Making a Fax Message (With Voice) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
From Your Company Fax System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
From Your Own Mailbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Using Your PC for Fax Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Downloading and Installing Fax Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Sending a Fax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Viewing and Forwarding Fax Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Using Your PC for Voice Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Outlook Client Plug-in for Microsoft Outlook 2010, 2013 and 2016 . . . . . . . . . . . . . . . . . . . . . . 25
Install the Outlook Client Plug-in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
NuPoint Unified Messaging Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Multimedia Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Configure the NuPoint Account Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Navigate Voice Messages in Outlook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Play a Voice Message in Outlook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Send a New Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Reply to a Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Forward a Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
View a Fax Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Text-to-Speech (TTS) Optional Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Playing a Text-to-Speech Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
iv
Table of Contents
Speech Auto Attendant Optional Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Speaking Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Universal Voice Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Making Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Placing a Call with Voice Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Placing a Call with Digit Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Cancelling a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Calling the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Speech Navigation Optional Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Speaking Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Universal Voice Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Enabling Speech Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Entering Voice Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Accessing Your Mailbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Accessing the Voice Mail and Email Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Managing Your Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Accessing Other Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
v
Document Title - Using Variables
vi
INTRODUCTION
ABOUT YOUR VOICE MAIL
Mitel® NuPoint Unified Messaging™ (UM) allows you to manage your voice mail, Record-A-Call
(RAC), fax, and Microsoft® Outlook® email messages from a touch-tone phone as well as from
your PC.
Voice mail, Record-A-Call, fax, and email are all "messages" that are accessible through your
voice mailbox and that you access using a menu system. The Voice Mail menu provides access
to most of the voice mailbox features and options including fax messages. Any voice mail user
can access this menu. The Email menu only provides access to emails and is available only
to users with the Advanced Unified Messaging feature with Text-to-Speech option.
In addition to accessing your messages over the phone, you can now play and manage your
voice messages from your Microsoft Outlook inbox. You install a plug-in player that allows you
to play voice messages from your email inbox over your PC speakers or over the phone. To
use this feature, you must have the Advanced Unified Messaging feature. For more information,
see “Using Your PC for Fax Messages” on page 21.
A Speech Auto Attendant (SAA) is also available to place calls to people by using voice
commands. The SAA is a speech-enabled application that allows you to place calls to people
quickly and efficiently by speaking their names. In addition to placing calls by name, you can
say a department name or telephone number. A tutorial introduces you to the system features,
and voice-based help is available to answer questions. See “Speech Auto Attendant Optional
Feature” on page 36 for more information.
The Speech Navigation optional feature enables users to manage their mailboxes using voice
commands. Instead of struggling to find and press a button on their telephone dial, they can
simply “say the command" from their principal or alternate extension. This is particularly helpful
for drivers who wish to use their cell phones in hands-free mode.
Note: Depending on how your mailbox is configured, you may not have all of the options
described in this guide. Consult your System Administrator for more information.
ABOUT THIS DOCUMENT
This guide provides instructions on the functionality of the Mitel telephone user interface (TUI),
Mitel Outlook Client Plug-in, and Speech Auto Attendant. If you use another supported email
client, please refer to the Web View Help for more information. Also refer to the NuPoint Unified
Messaging Mitel TUI Quick Reference Guide on http://edocs.mitel.com/UG/Index.html.
YOUR TELEPHONE
Before using the voice mail features of your system, familiarize yourself with your telephone.
•
Message key - Used to call the NuPoint UM Voice system and access your mailbox.
•
Keypad - Used to make menu selections within the voice mail system.
•
Message light - Used to indicate when you have new voice messages in your mailbox.
1
NuPoint UM User Guide
•
Softkeys - Used to select many of the voice mail menu options. To select a menu option
that appears in the telephone display, you can press either the associated context-sensitive
softkey that appears in your phone’s digital display or the keypad digit for the option.
Note: The softkey names used in this guide may differ slightly depending on your
telephone. For example, the Del (delete) softkey may appear as the Discard softkey,
on specific phones.
PREPARING TO ACCESS YOUR MAILBOX
Before accessing your mailbox, be sure to get the following information from your System
Administrator:
•
the NuPoint UM Receptionist number (optional)
•
the NuPoint UM Voice system access extension
•
your mailbox number
•
your default passcode.
If you have any problems or questions about procedures, consult your System Administrator.
2
ACCESSING YOUR MAILBOX
All of your voice messages will reside in your personal "mailbox", which is passcode protected.
Your System Administrator will assign you a temporary passcode to use the first time you access
your mailbox. How you log into your mailbox will depend on whether you’re calling from inside
or outside your company.
INSIDE YOUR COMPANY
FROM YOUR OWN EXTENSION
1.
Dial the internal NuPoint UM Voice access number.
2.
Enter your passcode when prompted.
FROM ANOTHER EXTENSION
1.
Dial the internal NuPoint UM Voice access number.
2.
Press the
3.
Enter your mailbox number followed by the
4.
Enter your passcode when prompted.
key when prompted to enter a passcode
key.
OUTSIDE YOUR COMPANY
FROM AN OUTSIDE LINE
1.
Dial the external NuPoint UM Voice access number.
2.
Enter your mailbox number followed by the
3.
Enter your passcode when prompted.
key.
FROM AN OUTSIDE LINE TO THE AUTOMATED RECEPTIONIST
1.
Dial the NuPoint UM Receptionist number.
2.
Press the
3.
Enter your mailbox number followed by the
4.
Enter your passcode when prompted.
key to access the NuPoint UM Voice system.
key.
3
NuPoint UM User Guide
SETTING UP YOUR MAILBOX
When you access your mailbox for the first time, a user tutorial automatically activates. This
tutorial guides you through your first mailbox session, explains how to record a greeting and
your name, and prompts you to change your temporary passcode.
Tip: After playing or sending messages, the system may return you to a previous menu
with different options than the menu you were just using.
MENU OVERVIEW
For an illustration of the menu overview, refer to the NuPoint Unified Messaging Mitel TUI Quick
Reference Guide (http://edocs.mitel.com/UG/Index.html).
GREETINGS
After opening your mailbox, you will be asked to record one or more greetings that callers will
hear when they call your mailbox. For example, you may record one greeting that callers hear
when your line is busy (such as, "I’m currently on the phone and unable to take your call") and
a different one when you’re not at your phone (such as, "I’m currently away from my desk").
If your System Administrator has enabled the Extended Absence Greeting feature for your
mailbox, you can also record an Extended Absence Greeting. This greeting allows you to inform
callers of an extended absence. Callers cannot press a key to skip the greeting. At the end of
the greeting, callers can either transfer to the attendant or leave a message.
Note: Once recorded, the Extended Absence Greeting is effectively enabled. This
means that all callers being forwarded to your mailbox will hear the extended absence
greeting. Once you log into your voicemail, you will be prompted to press 1 to retain
your Extended Absence Greeting, or to press 2 to disable the Extended Absence
Greeting.
If your System Administrator has disabled message delivery for the Extended Absence
Greeting, then after the greeting, callers will only be able to transfer to the attendant. See
“Greetings, Name and Passcode” on page 11.
NAME
You will be prompted to record your name so that the system can:
4
•
Address you when you call into the system (for example, "Hello, Jane Smith").
•
Inform other users when a message comes from you (for example, "4:45 p.m., from Jane
Smith").
•
State your name to other users when they address messages to your mailbox (for example,
"Jane Smith").
PASSCODE
You will always be prompted for your passcode before accessing your mailbox. The first time
you access your mailbox, you will use the temporary passcode assigned by the System
Administrator. During the tutorial, you will be prompted to change your passcode to a number
containing 4 to 10 digits. Define a passcode that you can easily remember, but do not select
an obvious code like "1234".
Note: Passcodes are required only if you wish to protect your privacy; you can choose
not to have a passcode by pressing 0000 when prompted during the tutorial.
When your mailbox is set up, you’re ready to start using the NuPoint UM Voice features.
Note: For added security, your Administrator may configure your passcode to expire at
regular intervals.
5
NuPoint UM User Guide
PLAYING MESSAGES
When you access your mailbox to retrieve your messages, the system tells you how many
messages you have ("You have 2 urgent messages and 2 unplayed messages."). For Advanced
Unified Messaging (UM) users with the Text-to-Speech (TTS) option, the system tells you how
many voice mails and emails you have ("You have 2 unplayed messages, 1 saved message,
3 unplayed emails, and 1 saved email).
You access voice mails and emails from separate menus. After the message summary,
Advanced UM with TTS users can access either the voice mail or the email menu. You can exit
either menu to access the other one.
Notes:
1. Advanced UM users who do not have the TTS option cannot access the email menu.
2. If the system experiences a delay obtaining information from the email server, it may
be unable to tell you how many email messages you have. To avoid this problem,
keep fewer than 10,000 emails in your mailbox.
3. If your mailbox is nearly full (80% of capacity), you will receive a warning message
instructing you to delete unneeded messages. The warning is played as a prompt
when you log in to your mailbox and emailed to the address programmed in your
mailbox parameters.
ACCESSING THE VOICE MAIL AND EMAIL MENUS
After you access your mailbox
•
If you are a regular voice mail user, you are already in the Voice Mail menu.
•
If you have the Advanced UM with TTS feature, you press
menu or
to access the Email menu.
to access the Voice Mail
PLAYING YOUR MESSAGES
After accessing either the Voice Mail menu or the Email menu, press
•
or the Play (or Play Message) softkey. Your urgent messages will automatically be
played first. Then, depending on your mailbox settings, you may have the option to play
unplayed or saved messages first; otherwise, your unplayed messages will be played first.
Note: If the date and time option is enabled on your voice mail system, the system will
automatically play this information at the beginning of each message. Consult your
System Administrator for more information.
6
WHILE LISTENING TO A MESSAGE
At any time during message playback you can
PRESS THIS KEY,
OR
PRESS THIS
SOFTKEY
TO PERFORM THIS ACTION
More then Pause
Pause the message for 30 seconds.
←
Move back five seconds within the message.
Æ
Move forward five seconds within the message.
Skip
Skip to your next message.
More then Play
Return to the beginning of your previous message.
Note: You may not have access to all of the options above, depending on how your
mailbox is configured. Consult your System Administrator for more information.
WHEN YOU HAVE FINISHED LISTENING TO A MESSAGE
At the end of a message, you can
PRESS
THIS KEY,
OR
PRESS THIS
SOFTKEY
TO PERFORM THIS ACTION
Play (or Restart)
Play the message again.
Answer
Answer the person who sent the message.
When you are finished recording your answer, press
or the Send softkey to send it and continue your session.
Then press
to send your answer to additional mailboxes if you wish.
7
NuPoint UM User Guide
PRESS
THIS KEY,
OR
PRESS THIS
SOFTKEY
Answer (with
Dial-back option
enabled)
TO PERFORM THIS ACTION
to answer by voice mail (as above)
to dial-back the caller and then delete the message.
to dial-back the caller and then keep the message.
Give
Give the message to another mailbox, distribution list, or off-system
telephone number.
The system will also give you the opportunity to record additional
comments before sending the message to someone else.
When you have added your comments, press
or the Send (or Exit) softkey and continue your session.
Then press
to give the message to additional mailboxes if you wish.
Keep
Keep the message.
Kept messages can be accessed only after you have skipped
through your unplayed messages and message receipt queues.
Del (or Discard)
Discard the message.
Note: If you accidentally discard a message, you can retrieve it by immediately pressing
or the Undelete softkey. If you press any key other than the
key immediately
after discarding the message, you will not be able to retrieve the discarded message.
Note: You may not have access to all of the options above, depending on how your
mailbox is configured. Consult your System Administrator for more information.
8
MAKING MESSAGES
To make a message, you must first access your mailbox by calling the system access number
and entering your passcode. You can then make a voice message before or after listening to
any unplayed messages in your mailbox. Remember that you can address your messages to
other mailboxes, distribution lists, and off-system telephone numbers.
MAKING A VOICE MESSAGE
RECORDING A VOICE MESSAGE
1.
Press
or the Make Message softkey to make a message.
2.
Enter the recipient's number or, to dial by name, press the specific key assigned to this
feature on your voice mail system, and then dial the recipient's last name and first name
until the system recognizes the name.
Note: The system will automatically announce the specific key to press to dial by name.
This is a configurable feature and thus the key to press will vary for each voice mail
system.
3.
After the system confirms the recipient's name, enter the names or numbers of any other
intended recipients (for example, you may wish to send a single message to all members
of a certain committee, telling them the time and place of the next committee meeting).
4.
When you have finished addressing your message, press
5.
Begin recording your message after the tone. (You may press
or the Record softkey.
to pause during
recording and then any key to resume recording, or you may use the Pause/Resume
softkeys.)
SENDING A MESSAGE WHEN YOU HAVE FINISHED RECORDING
Once you have finished recording, you may choose to send, review, modify, cancel, or specify
special delivery for your voice message, by selecting from the following options:
PRESS
THIS KEY,
OR
PRESS THIS
SOFTKEY
TO PERFORM THIS ACTION
Send
Send the message and exit to the main menu.
Append
Add to the recording.
Del
Delete the recording and start over.
9
NuPoint UM User Guide
PRESS
THIS KEY,
OR
PRESS THIS
SOFTKEY
TO PERFORM THIS ACTION
Review
Replay the message.
End Record
Access message addressing options such as urgent delivery, future
delivery, confidential, and return receipt.
Once you have selected from these options, press
or the Send (or Exit) softkey to send your message and exit
to the main menu.
Note: If you regularly send messages to multiple users, consider creating personal
distribution lists to make addressing your messages even easier (see “Distribution Lists”
on page 12).
10
USER OPTIONS
The user options menu allows you to listen to the user tutorial, change your greetings, record
your name, and define your password, create voice mail distribution lists, and select call
scheduling options.
ACCESSING USER OPTIONS AND USER TUTORIAL
Press
or the Options softkey to access user options from the main menu.
You can press
at any time to go through the user tutorial again.
GREETINGS, NAME AND PASSCODE
When you first set up your mailbox (see “Setting Up Your Mailbox” on page 4), you recorded a
greeting and your name and selected a passcode. The user options menu allows you to change
these at any time. You should update your greeting(s) regularly — for example, to let callers
know whether you're in or out of the office.
From the user options menu, you can
PRESS
THIS
KEY, OR
PRESS
THIS
SOFTKEY
Greetings
TO PERFORM THIS ACTION
Change your greeting(s). You can record a Primary greeting and one or
more Conditional greetings. Record Conditional greetings you want callers
to hear when your line is busy (e.g., "I’m currently on the phone and unable
to take your call"), when you’re not there (e.g., "I’m currently away from my
desk"), or for extended absences ("I will be away until October 15th,...").
You can now press
personal greeting,
greeting, or
to record or change your conditional
to record or change your primary personal
to enable your Extended Absence Greeting.
After you have recorded your greeting, press
or the Chng softkey to select which greeting—Primary or
Conditional—you want your callers to hear.
Change
Name
Re-record your name.
Passcode
Change your passcode.
Note: You may not have access to Conditional greetings, depending on how your
mailbox is configured. Consult your System Administrator for more information.
11
NuPoint UM User Guide
DISTRIBUTION LISTS
A distribution list allows you to record a single message and then send it to a large number of
people without addressing them each individually. You can use distribution lists whenever you
make a message, or give a message to someone else.
CREATING OR MODIFYING A DISTRIBUTION LIST
1.
Press
or the Dist Lists softkey from the user options menu.
2.
Enter the number of the distribution list, ensuring the first digit is always zero (0).
3.
Press
to record a name for the distribution list (e.g., "product planning committee").
The system will play this name each time you address messages to this distribution list.
4.
Press
to add members to the list; press
to drop members.
5.
Enter the numbers or names of users you wish to add or drop.
6.
Press
if you would like the system to play back the list of members you have selected.
7.
Press
to exit to the main menu.
Note: All personal distribution lists must begin with the number 0.
USING A DISTRIBUTION LIST
•
Instead of entering a mailbox number, enter the number of the distribution list you want to
use. The system reads back the number of the distribution list.
CALL SCHEDULE OPTIONS
NUPOINT WAKEUP
NuPoint UM WakeUp allows you to program NuPoint UM Voice to call you at a specific telephone
number at a specific time. You can schedule wake up calls for Monday through Friday,
weekends, every day, or as needed.
1.
From the user options menu, press
2.
At the Call Schedule Options menu, press
3.
To schedule wakeup calls:
•
press
to reach NP WakeUp.
enter the time for the wakeup call (two digits for the hour, two digits for the
minute). If prompted, press
12
to reach Call Schedule Options.
for a.m. or
•
press
to make this a daily wakeup call.
•
press
to cancel this wakeup call.
for p.m.
•
press
to change the time.
4.
To cancel all wakeup calls, press
.
5.
To exit to the User Options menu, press
.
PAGER
Paging allows you to define a schedule so that when a message arrives in your mailbox, NuPoint
UM Voice notifies your pager.
1.
From the user options menu, press
to reach Call Schedule Options.
2.
At the Call Schedule Options menu, press
3.
At the Paging menu, select an option:
to reach Paging.
•
press
to review the schedule.
•
press
to disable paging.
•
press
to change the telephone number.
•
press
to change the time.
•
press
to exit to the User Options menu.
MESSAGE DELIVERY
Message Delivery allows you to define a schedule so that if a message arrives in your mailbox,
NuPoint UM Voice will call you at a specific telephone number at a specific time so that you
can retrieve the message.
1.
From the user options menu, press
to reach Call Schedule Options.
2.
At the Call Schedule Options menu, press
3.
At the Message Delivery menu, select an option:
to reach Message Delivery.
•
press
to review the schedule.
•
press
to disable message delivery.
•
press
to change the telephone number.
•
press
to change the time.
•
press
to exit to the User Options menu.
13
NuPoint UM User Guide
FUTURE DELIVERY AUDIT
Future Delivery Audit allows you to audit any message scheduled for future delivery. You can
schedule delivery of any message up to 365 days in the future using the message addressing
options menu. See “Sending a Message when You Have Finished Recording” on page 9.
14
1.
From the user options menu, press
to reach Call Schedule Options.
2.
At the Call Schedule Options menu, press
3.
At the Future Delivery Audit menu, select an option
to reach Future Delivery Audit.
•
press
to audit the message.
•
press
to discard the message.
•
press
to keep the message.
•
press
to play the recipients.
•
press
to hear the delivery time.
•
press
to exit to the User Options menu.
RECORD-A-CALL OPTIONAL FEATURE
The Record A Call feature allows you to use your NuPoint UM Voice system to record your
telephone conversations.
Note: You may be required by law to inform the other party that you are recording the
conversation. For specific instructions, consult your System Administrator.
RECORDING WHILE ON A TWO-PARTY CALL
Your system may be programmed to automatically begin recording external calls when you or
the other party answers. Contact your System Administrator for details.
If your system does not automatically record conversations, you must press a Record key to
begin recording while you are on a two-party call. What key you press depends on whether the
Softkey feature is available on your phone. The following phones support softkeys:
•
Superset 4150
•
5140 IP
•
5240 IP
RECORDING USING SOFTKEYS
•
To begin recording while you are on a two-party call, press the Record softkey that appears
on your phone’s digital display screen.
Pausing or resuming recording during a call
•
To pause the recording press the Pause softkey.
•
To resume recording after pausing, press the Resume softkey.
Stopping the recording
•
To stop the recording without saving the recorded conversation, press the Stop and Erase
softkeys.
•
To stop and save a recording, press the Stop and Save softkeys.
Note: Your administrator may configure your Record A Call settings to automatically
save a recorded conversation when you hang up the phone. If auto-save is enabled,
you can save the recorded call simply by hanging up the phone at the end of your
conversation.
15
NuPoint UM User Guide
RECORDING USING HARD KEYS
To begin recording a call using hard keys, press the Record key that your System Administrator
has programmed on your phone.
Note: Using hard keys with Record A Call, you can only start a recording session. Your
System Administrator must enable auto-save in order for your conversations to be saved
automatically when you hang up the phone. Consult your System Administrator for more
information.
PLACING A CALL ON HOLD WHILE RECORDING
•
Putting a call on hold during the recording saves the recording, and sends it to your mailbox.
•
Taking the call off hold starts a new recording session.
Note: Depending on system programming, hanging up, or pressing TRANS/CONF or
a line appearance key, may also save the recording. Consult your System Administrator
for details.
LISTENING TO A RECORDING
To listen to a recorded conversation after the call has ended
16
1.
Lift your handset.
2.
Access your voice mailbox.
3.
Follow the prompts to retrieve the recording, as you would to retrieve any regular voice
message.
FAX OPTIONAL FEATURE
The Fax feature allows you to manage fax messages that are sent to your mailbox, using the
TUI. You can retrieve unplayed fax messages, play a voice message that accompanies a fax,
send a fax to a fax machine, and deliver a fax (with or without a voice message) to another user.
FAX DELIVERY OPTIONS
You can access Fax delivery options from the User Options menu. From the Main menu, press
and then
to access the following Fax Delivery options:
PRESS THIS
KEY
TO PERFORM THIS ACTION
To send all unplayed fax messages in your mailbox to your default fax number.
To define a default fax delivery number. All your faxes will be automatically sent to
this number when you press
from while you are in the Fax delivery
menu.
To fax into your mailbox a cover page that will become your Personal Cover Page.
This page will be automatically included with all faxes that you send from your
mailbox.
From a fax phone
To toggle between enabling and disabling automatic fax delivery to your default fax
number. Automatic fax delivery immediately sends all fax messages that arrive in
your mailbox to your default fax number.
PLAYING AND PRINTING FAX MESSAGES
Fax messages are treated just like voice messages in your mailbox. When you access your
mailbox to retrieve messages, the system will first tell you how many messages you have, for
example, "You have 2 urgent messages and 4 unplayed messages with fax".)
FROM A TELEPHONE
To play a fax message:
1.
After accessing your mailbox, press
or the Play (or Play Message) softkey. Your
urgent messages will automatically be played first.
2.
For any fax messages, the system will prompt you to press
From this menu, you can:
•
Press
for fax delivery options.
to dial the number of a fax machine where you want the fax to be printed. Dial the
number when prompted.
17
NuPoint UM User Guide
•
The system will confirm the number. Press
to accept the number, or press
to dial a new number.
•
After you press
to accept the number, press
to that number, or press
3.
to deliver the fax immediately
to schedule a time for future delivery.
If you have additional fax messages, you can send them to the same fax number you
entered for the first number simply by pressing
and then
.
Note: You can also use the fax delivery options under the User Options menu (refer to
the Mitel TUI Quick Reference Guide). Using this menu, you can set up a default fax
delivery number. After you program that number, you can simply press
delivery options (after playing the message with fax), and then press
for fax
to print your
fax message.
FROM A FAX PHONE
To retrieve and print a fax message from a fax phone:
1.
After accessing your mailbox, press
or the Play (or Play Message) softkey, and then
press
to access the Fax Delivery Options menu.
2.
Press
to receive a fax message print out from that fax machine.
3.
When prompted, press the Start button on the fax machine.
4.
Once you receive the fax print-out, you can stay on the line to resume your mailbox session.
WHEN YOU HAVE FINISHED LISTENING TO A FAX MESSAGE
See “When You Have Finished Listening to a Message” on page 7.
MAKING A FAX MESSAGE (WITHOUT VOICE)
You can send a fax message to a recipient’s mailbox, using a fax phone. You can send the
message directly from your company’s fax system or from your own mailbox. If you send a fax
from your company’s fax system, your name is not included in the message header; and if you
send a fax from your own mailbox, your name is included in the message header.
FROM YOUR COMPANY FAX SYSTEM
Note: Your name will not be included in the recipient’s message header.
18
1.
From a fax phone, dial your company Fax system access number.
2.
When you hear the system greeting, enter the recipient’s mailbox number, or to dial by
name, press the appropriate keys to dial the recipient’s last name followed by their first
name until the system recognizes the name.
3.
You will hear the recipient’s personal greeting. At the tone, press the Start button on the
fax machine to send your fax.
4.
After the fax has been sent, you can press
press
to mark the message urgent, or you can
to leave a message for another mailbox.
FROM YOUR OWN MAILBOX
Note: Your name will be included in the recipient’s message header.
1.
Access your mailbox, and when you hear your own greeting, press
2.
Enter your passcode.
3.
Press
4.
Enter the recipient’s mailbox number, or to dial by name, press the appropriate keys to dial
the recipient’s last name followed by their first name until the system recognizes the name.
5.
Once the system confirms the recipient’s name, enter the names or numbers of any other
intended recipients.
6.
When you are finished addressing your fax message, press
to make a message.
to leave a fax, and then
press the Start button on your fax machine to send your fax, or press
7.
.
After the fax has been sent, you can press
for more options.
to send the message; or press
to
access message addressing options such as urgent delivery, future delivery, confidential,
and return receipt. Once you have selected from these options, press
to send
your message and exit to the main menu.
19
NuPoint UM User Guide
MAKING A FAX MESSAGE (WITH VOICE)
You can send a combined voice and fax message to a recipient’s mailbox, using a fax phone.
You can send the message directly from your company’s fax system or from your own mailbox.
If you send a fax from your company’s fax system, your name is not included in the message
header; and if you send a fax from your own mailbox, your name is included in the message
header.
FROM YOUR COMPANY FAX SYSTEM
Note: Your name will not be included in the recipient’s message header.
1.
From a fax phone, dial your company’s Fax system access number.
2.
When you hear the system greeting, enter the recipient’s mailbox number, or to dial by
name, press the appropriate keys to dial the recipient’s last name followed by their first
name until the system recognizes the name.
3.
You will hear the recipient’s personal greeting. At the tone, record a voice message.
4.
When you are finished recording your voice message, press the Start button on your fax
machine to send your fax.
5.
After the fax has been sent, you can press
press
to mark the message urgent, or you can
to leave a message for another mailbox.
FROM YOUR OWN MAILBOX
Note: Your name will be included in the recipient’s message header.
1.
From a fax phone, dial your company’s Fax system access number.
2.
When you hear the system greeting, enter your own mailbox number.
3.
When you hear your own greeting, press
4.
Enter your passcode.
5.
Press
.
to make a message, and then follow the instructions for sending a voice-only
message from your mailbox (including addressing).
6.
At the tone, record a voice message.
7.
When you are finished recording, press
to leave a fax, and then press the Start button
on your fax machine to send your fax, or press
20
for more options.
USING YOUR PC FOR FAX MESSAGES
You can also use your PC to manage fax messages. The Fax feature allows you to add the
Fax Printer driver to your Printers folder. Using Fax Printer, you can send faxes from any
application with a Print function.
Faxes can also be sent from the Web View interface. For information about sending faxes from
the Web View interface, refer to the Web View Help.
Note: Custom Cover Pages must be in TIFF format only.
DOWNLOADING AND INSTALLING FAX PRINTER
To use the Fax Printer for fax messages, you must first download and install it to your PC from
the Web View interface.
To download and install the Fax Printer driver:
Notes:
1. To install the Fax Printer driver, you must have local administrator rights on the PC,
and access to the Internet.
2. The Fax Printer driver can be installed on one of the following operating systems:
Windows 2000, 2003, Vista (Business, Enterprise or Ultimate), Windows 7.0,
Windows 8.0/8.1, or Windows 10.
3. The Fax Printer driver supports most file formats, including DOC, PDF and XLS. It
does not, however, support TIFF files on Windows 7.0 and Windows 8.0.
1.
Log in to the Web View interface and click on the Downloads tab.
2.
Click on Download Fax Printer. Internet access is required.
3.
In the Security Warning window, click Run to run FaxPrinter.exe. The installation will start
automatically.
4.
Click Next on each dialog. When prompted, accept the Terms of Use.
The Fax Printer driver is now installed.
SENDING A FAX
Faxes can be sent using the NuPoint Fax Printer using any software with a Print function. If
you wish, you can set up a Personal Cover Page (see Fax Delivery Options) or create Custom
Cover Pages. If you have a Personal Cover Page, it will be the default cover page for faxes
you send.
Only TIFF format can be used as a Custom Cover Page. You can save multiple Custom Cover
Pages to customize your faxes for their recipients.
21
NuPoint UM User Guide
To send a Fax using the NuPoint Fax Printer:
Note:
1. Before sending a fax for the first time, obtain the fully qualified domain name or IP
address of the NuPoint UM server from your System Administrator.
2. If you have a Windows 7.0 or Windows 8.0 operating system, you cannot send faxes
in TIFF format. Other file formats, such as DOC, PDF, and XLS, are supported.
1.
Open the document and select Print. In the print menu, select NuPoint Fax Printer from
the list of available printers.
OR
If NuPoint Fax Printer has been set up as your default printer, right click on the document
in Windows Explorer and select Print.
When the document is ready to be sent to the server, the NuPoint Fax Client window will
appear.
If you have never sent a fax before or the client could not connect to the server, the Server
Settings tab will display:
Figure 1: Server Settings Tab
Note: If your mailbox password changes, you will need to update the Server Settings
tab with the new password the next time you send a fax.
2.
Enter your credentials to connect to the server.
a.
In the NuPoint Server field, enter the fully qualified domain name (FQDN) of the server.
b. In the Mailbox field, enter your NuPoint UM mailbox number.
c.
In the Passcode field, enter your NuPoint UM mailbox passcode.
d. Click Connect. The Status will update to Connected.
22
3.
Click on the Delivery Options tab.
Figure 2: Delivery Options Tab
a.
In the Recipients field, enter the list of recipients (NuPoint UM mailbox numbers or fax
numbers), separated by commas.
Note: For external fax numbers, include any digits that must be dialed from your
system to reach an external line.
b. If you wish to use a Custom Cover Page, select the Use a Custom Cover Page check
box.
c.
Enter the full name of the cover page OR click on the Browse... button to select it
Note: If you do not use a Custom Cover Page, the server will use your Personal
Cover Page, or, if you do not have one, the System Cover Page.
d. Click on the Send Fax button.
When the fax has been received by the server, a popup will display with the message The fax
is successfully queued for delivery. If the fax cannot be sent, you will receive a message in
your voice mail to notify you of the failure.
When you send your next fax, the Server Settings tab will not display unless the Fax Printer
could not connect to the server, for example, if your password has changed.
VIEWING AND FORWARDING FAX MESSAGES
To view a Fax Message:
•
Open the message from your e-mail inbox and view the attached document. To be viewable,
the fax must not exceed the file size limit for the email client (20 MB for MS Outlook or 25
MB for Google Gmail).
•
From the Messages tab in the Web View interface, click on the Play button. Depending on
its file format, the fax will open in a TIFF or PDF viewer.
•
From your telephone, send the fax to a fax machine.
23
NuPoint UM User Guide
To forward a Fax Message:
•
From the Messages tab in the Web View interface, click on the Forward Fax button to
forward the message as a fax.
OR
•
24
From the Messages tab in the Web View interface, click on the Forward button to forward
the message as an attachment to an e-mail.
USING YOUR PC FOR VOICE MESSAGES
If you are an Advanced Unified Messaging (UM) user, you can install the Mitel Outlook Client
Plug-in (OCP) in your Microsoft® Outlook email client and use it to manage your messages.
The OCP enables you to listen to your voice messages on either your phone or your PC. You
can also use it navigate through the list of your messages, reply to and forward messages, and
record new voice messages to be sent as email attachments.
Four types of NuPoint UM messages are supported by the OCP: voice messages, confidential
voice messages, Record-A-Call messages, and fax messages. Each message type has a
unique icon to help identify it.
OUTLOOK CLIENT PLUG-IN FOR MICROSOFT OUTLOOK 2010, 2013
AND 2016
If you are a NuPoint Unified Messaging Advanced user with Outlook 2010, 2013 and 2016, use
the following procedures to install the Mitel Outlook Client Plug-in and manage your messages.
Notes:
1. The OCP works with the 32-bit and 64-bit variants of Microsoft Outlook 2010, 2013
and 2016 installed on one of the following operating systems: Vista (Business,
Enterprise or Ultimate), or Windows 7 (Enterprise or Ultimate), Windows 8.0/8.1, or
Windows 10.
2. If a voicemail message is moved from the Inbox to a personal folder, the message
is deleted from the telephone user interface (TUI). If the message is then moved
back to the Inbox, it is deleted since the associated TUI message has been deleted.
The message may reside in the Deleted folder if the permanent delete configuration
parameter is disabled. See your System Administrator for more information.
3. A phone or extension is required to create new voicemails, reply to voicemails, and
forward voicemails using the Call Me/Meet Me feature.
4. A PC sound card and speakers/headset is required to listen to voicemail messages
through your computer.
5. After deleting a message in Outlook, you may experience a delay of up to ten minutes
before your MWI lamp is extinguished. This is a known issue with Microsoft
Exchange 2013. If your enterprise is using another type of mail server, you should
not experience any delay with message synchronization.
INSTALL THE OUTLOOK CLIENT PLUG-IN
Note: Once you have installed the plug-in, Outlook takes slightly longer to open and
close. Avoid restarting Outlook immediately after closing it.
Before You Begin
Obtain the following information from your System Administrator before you begin this
procedure:
25
NuPoint UM User Guide
•
The location of the OutlookClientPlugin.exe file
Note: To install the Outlook Client Plug-in, you must have local administrator rights on
the PC.
To install the plug-in on Microsoft Outlet 2010, 2013 and 2016 (32- or 64-bit variant):
1.
Close Microsoft Outlook if you have it open.
2.
If you have the Outlook Client Plug-in previously installed, remove the application with
Add/Remove Programs in Control Panel:
-
Click Start > Control Panel, and then open Add or Remove Programs.
-
Select Outlook Client Plug-in, and then click Change/Remove.
-
Navigate to the OutlookClientPlugin.exe file for the Outlook Client Plug-in, and then
double-click the file and click Run. You may have to click Run a second time if you get
a security warning. The Outlook Client Plug-in Setup window opens.
Note: The OutlookClientPlugin.exe file can be installed from either Mitel OnLine
or the Downloads tab in the Web View interface. If this tab is unavailable, see your
system administrator in order to have the OCP download enabled on your mailbox.
3.
If you are asked to remove the existing application, click OK.
4.
If you are asked permission to continue the installation, click Continue.
5.
Click Next. The License Agreement window opens.
6.
Select the button to agree with the terms of the license agreement.
7.
Click Next. The User Settings window opens.
8.
Enter the address of the NuPoint Unified Messaging platform, and click Next. The Choose
Destination Location window opens.
9.
Click Next to accept the default setting for the installation location or click Change to place
the files in another location. After you have specified the location, the Start Copying Files
window opens.
10. Click Next. The software installs, and then the InstallShield Wizard Complete window
opens.
11. Click Finish.
12. Open Microsoft Outlook, and confirm that the Mitel NuPoint UM tab appears in the Ribbon.
NUPOINT UNIFIED MESSAGING TAB
Once the Mitel Outlook Client Plug-in has been installed, the Unified Messaging tab appears
in the Ribbon located in the upper portion of Microsoft Outlook 2010, 2013 or 2016.
26
Figure 3: Mitel NuPoint UM tab in Outlook 2010/2013/2016 Ribbon
The following buttons are available on the Mitel NuPoint UM tab:
•
Next Voice Message: Locates the NuPoint UM message that appears after the currently
selected NuPoint UM message.
•
Previous Voice Message: Locates the NuPoint UM message that appears before the
currently selected NuPoint UM message.
•
New Voice Message: Create a new voice message and send it to one or more NuPoint
users.
•
Reply with Voice: Sends a reply to the sender of a NuPoint UM message with a voice
message.
•
Forward with Voice: Forwards a NuPoint UM message to another user with a voice
message.
•
Delete Message: Deletes any type of message (not just voice messages).
•
Autoplay: This button toggles the Autoplay feature on and off. When the feature is on,
NuPoint UM messages are played as soon as they selected (highlighted or opened). When
the feature is off, you must select the message and click the Play button.
•
Settings: Click this button to configure mailbox settings that enable you to send new voice
messages, reply to messages, forward messages, and listen to confidential messages.
•
About: Displays the version number of the Outlook Client Plug-in for Outlook 2010, 2013
and 2016.
MULTIMEDIA CONTROLS
Voice Messages
The following multimedia controls appear on NuPoint UM voice messages received in Outlook
2010, 2013 and 2016:
Figure 4: Voice Message Multimedia Controls in Outlook 2010/2013/2016
If the message contains multiple attachments (original message and replies), they are displayed
above the multimedia controls.
The multimedia controls enable you to do the following:
•
Play: Click the play button to play the message.
•
Stop: Click the stop button to stop message playback.
•
Volume slider: Use the volume slider to adjust or mute the playback volume.
•
Playback slider: Use the playback slider to select a particular point in the audio file.
•
Phone: Click to connect to your NuPoint UM mailbox and play back messages through the
telephone
27
NuPoint UM User Guide
•
Save: Use the save button to save all attachments (original message and replies) to a
storage medium.
Fax Messages
Once the Mitel Outlook Client Plug-in has been installed, multimedia controls appear on NuPoint
UM fax messages received in Outlook 2010, 2013 and 2016.
Figure 5: Fax Message Multimedia Controls in Outlook 2010/2013/2016
The multimedia controls enable you to do the following:
•
View fax: Press the play button to open the fax message in a TIFF viewer such as Windows
Photo Viewer or a PDF viewer such as Adobe Acrobat. To be viewable, the fax must not
exceed the file size limit for Outlook (20 MB).
•
Save: Use the save button to save the fax file to a storage medium.
CONFIGURE THE NUPOINT ACCOUNT SETTINGS
You must configure your NuPoint account settings before you can access the following functions
using the Call/Meet Me feature:
-
Listen to a confidential voicemail
-
Create a new voicemail
-
Reply to a voicemail with a voice message
-
Forward a voicemail with a voice message
To update the settings:
1.
In Microsoft Outlook, click Mitel NuPoint UM > Settings. The Settings dialog displays.
Figure 6: NuPoint Account Settings
28
2.
In the NuPoint Server field, enter the fully qualified domain name (FQDN) of the server.
3.
In the Mailbox field, enter your NuPoint UM mailbox number.
4.
In the Passcode field, enter your NuPoint UM mailbox passcode.
5.
Program the system to use either Call Me or Meet Me functionality:
•
For Call Me, select NuPoint will Call Me at the following number, enter your extension
number, and select Same as Mailbox if your extension is the same as your mailbox. When
you require a phone, the system will automatically dial your number.
•
For Meet Me, select I will call into the NuPoint system. When you require a phone, you
will be prompted to manually enter your extension number and log in.
6.
Click Test connection to validate the connection to the NuPoint UM server.
If the test is successful, the dialog displays a check mark. If the test is unsuccessful, the
dialog displays an "X" mark and lists the faulty setting (server address, passcode, etc.).
7.
Click OK.
Note: If you have not already tested the connection, it is tested when you press OK.
NAVIGATE VOICE MESSAGES IN OUTLOOK
To view the next NuPoint UM message in Outlook 2010, 2013 and 2016:
1.
In Microsoft Outlook, click Mitel NuPoint UM.
2.
Click the Next Voice Message button.
To view the previous NuPoint UM message in Outlook 2010, 2013 and 2016:
1.
In Microsoft Outlook, click Mitel NuPoint UM.
2.
Click the Previous Voice Message button.
PLAY A VOICE MESSAGE IN OUTLOOK
Use the Autoplay button in the NuPoint UM tab to control message playback. If Autoplay is
enabled, messages are played as soon as they are highlighted or opened. If Autoplay is
disabled, messages are played only when you select them and click the Play or Call Me/Meet
Me button.
Note: Fax and confidential voice messages cannot be played through the PC speakers.
Note: To save hard drive space, the Network Administrator may configure user email
accounts to receive voice messages in text format only.
29
NuPoint UM User Guide
To play a voice message in Outlook 2010, 2013 and 2016:
1.
In Microsoft Outlook, click Mitel NuPoint UM.
2.
Select a message in the inbox. (If Autoplay is enabled, message playback commences
immediately.)
3.
To play the message over your PC speakers, click the Play button. Use the multimedia
controls to control the following:
4.
5.
•
To stop playback, click Stop.
•
To change or mute the playback volume, adjust the volume slider.
•
To select a particular point in the recording, adjust the playback slider.
•
To save the audio file to storage media, click the Save button and follow the prompts.
To play the message in a Call Me or Meet Me session, click the Phone button.
•
If you selected the "Call Me" option in the NuPoint Account Settings, the system dials
your extension. When you answer the phone, the message is played. To stop playback,
click the Stop button. To exit the panel, click the Phone button.
•
If you selected the "Meet Me" option in the NuPoint Account Settings, the system
prompts you to call in to your voice mailbox and log in. Once you have logged in, the
message is played. To stop playback, click the Stop button. To exit the panel, click the
Phone button.
To delete the message from NuPoint UM, select it and click Delete on the Home ribbon.
Depending on the mail server in use, there may be a slight delay before your MWI is
extinguished.
SEND A NEW MESSAGE
You can record a new voice message using the Call Me/Meet Me feature and then send the
message as an email attachment. Before you can use this feature, you must enter your NuPoint
account settings.
To create a new voice message in Outlook 2010, 2013 and 2016:
1.
In Microsoft Outlook, click Mitel NuPoint UM.
2.
Click New Voice Message. The New Voice Message window opens.
Figure 7: New Voice Message in Outlook 2010/2013/2016
3.
30
To specify the message recipients:
a.
In the To: field, enter the names or mailbox numbers of the message recipients. Use
semicolons to separate multiple entries.
b. Click Check names to resolve the names and mailbox numbers to NuPoint UM users.
c.
4.
If all names can be resolved, you can continue to the next step. If any name cannot
be resolved, you will be prompted to remove it or, if the name is ambiguous, to select
an alternative.
To start the recording:
Note: Click Suppress prompt if you want to hear a beep, rather than a prompt,
prior to recording your voice message. Click Urgent message to mark it urgent.
a.
Click Record message and, depending on your account configuration, establish either
a Call Me or Meet Me session:
•
Call Me — The system dials your extension. When you answer the phone, the
message is played.
•
Meet Me — The system prompts you to call in to your voice mailbox and log in.
Once you have logged in, the message is played.
b. When you answer your extension telephone, you will hear a message ("You may start
your message now...") followed by a beep. If Select prompt has been selected, you
will only hear a beep.
c.
5.
Record your message. It can be up to three minutes long.
To stop the recording:
•
Click Stop.
•
Press # on the telephone.
•
Hang up the telephone.
If you have pressed Stop or #, you may review the message by clicking Review message.
If you have hung up, you must re-establish the recording session (by pressing Record
message) before you attempt to review the message.
6.
Click Send.
REPLY TO A MESSAGE
You can reply to a voice or fax message in Outlook with another voice message that you record
using the Call Me/Meet Me feature and then send as an email attachment. Before you can use
this feature, you must enter your NuPoint account settings.
Note: You can only reply to NuPoint voice messages using this procedure. Reply to
other messages with emails.
To reply to a voice message in Outlook 2010, 2013 and 2016:
1.
In Microsoft Outlook, click Mitel NuPoint UM.
2.
Highlight the message in the inbox, and then click Reply with Voice. The Reply with Voice
window opens.
31
NuPoint UM User Guide
Figure 8: Reply with Voice Message in Outlook 2010/2013/2016
3.
The To: field contains the name of the original sender. No changes or additions can be
made to this field.
4.
To start the recording:
Note: Click Suppress prompt if you want to hear a beep, rather than a prompt,
prior to recording your voice message. Click Urgent message to mark it urgent.
a.
Click Record comments and, depending on your account configuration, establish
either a Call Me or Meet Me session:
•
Call Me — The system dials your extension. When you answer the phone, the
message is played.
•
Meet Me — The system prompts you to call in to your voice mailbox and log in.
Once you have logged in, the message is played.
b. When you answer your extension telephone, you will hear a message ("You may start
your message now...") followed by a beep. If Select prompt has been selected, you
will only hear a beep.
c.
5.
6.
Record your message. It can be up to three minutes long.
To stop the recording:
•
Click Stop.
•
Press # on the telephone.
•
Hang up the telephone.
If you have pressed Stop or #, you may review the message by clicking Review comments.
If you have hung up, you must re-establish the recording session (by pressing Record
comments) before you attempt to review the message.
The original message is updated within the following note:
"You replied with voice to this message on <DAY DATE TIME>."
32
FORWARD A MESSAGE
You can forward a voice or fax message that you have received, and include another voice
message with it as an email attachment. Before you can use this feature, you must enter your
NuPoint account settings.
Note: If an Advanced UM user with a non-English language computer forwards a
voicemail message to another Advanced UM user, the message will be added to the
recipient’s email client but not to his or her NuPoint message store. As a result, the
message will be deleted when synchronization occurs. To avoid this problem, change
the subject line of voice messages forwarded from non-English language computers.
To forward a voice message in Outlook 2010, 2013 and 2016:
1.
In Microsoft Outlook, click Mitel NuPoint UM.
2.
Highlight the message in the inbox, and then click Forward with Voice. The Forward with
Voice window opens.
Figure 9: Forward with Voice Message in Outlook 2010/2013/2016
3.
To specify the message recipients:
a.
In the To: field, enter the names or mailbox numbers of the message recipients. Use
semicolons to separate multiple entries.
b. Click Check names to resolve the names and mailbox numbers to NuPoint UM users.
c.
4.
If all names can be resolved, you can continue to the next step. If any name cannot
be resolved, you will be prompted to remove it or, if the name is ambiguous, to select
an alternative.
To start the recording:
Note: Click Suppress prompt if you want to hear a beep, rather than a prompt,
prior to recording your voice message. Click Urgent message to mark it urgent.
a.
Click Record comments and, depending on your account configuration, establish
either a Call Me or Meet Me session:
•
Call Me — The system dials your extension. When you answer the phone, the
message is played.
•
Meet Me — The system prompts you to call in to your voice mailbox and log in.
Once you have logged in, the message is played.
33
NuPoint UM User Guide
b. When you answer your extension telephone, you will hear a message ("You may start
your message now...") followed by a beep. If Select prompt has been selected, you
will only hear a beep.
c.
5.
6.
Record your message. It can be up to three minutes long.
To stop the recording:
•
Click Stop.
•
Press # on the telephone.
•
Hang up the telephone.
If you have pressed Stop or #, you may review the message by clicking Review comments.
If you have hung up, you must re-establish the recording session (by pressing Record
comments) before you attempt to review the message.
The original message is updated within the following note:
"You forwarded this message to <NAMES> with voice to this message on <DAY DATE
TIME>."
VIEW A FAX MESSAGE
To view a fax message in Outlook 2010, 2013 and 2016:
1.
In Microsoft Outlook, click Mitel NuPoint UM.
2.
Select the message in the inbox.
3.
Click View Fax. Depending on its file format, the fax will display in either a TIFF viewer
(Windows Photo Viewer) or a PDF viewer (Adobe Acrobat). To be viewable, the fax must
not exceed the file size limit for the email client (20 MB for Outlook).
TEXT-TO-SPEECH (TTS) OPTIONAL FEATURE
The Text-to-Speech (TTS) feature allows you to listen to Microsoft Outlook and Google Mail
email messages from the NuPoint UM Voice mailbox. The text of the email message is
converted to speech and played back over the phone.
Note: TTS is only available with the Advanced Unified Messaging feature.
You can access Text-to-Speech options from the Message System Choice menu.
Note: You need to have TTS enabled in order to access this menu. Contact your System
Administrator for details.
From the Message System Choice menu, press
options:
34
to access the following Text-to-Speech
PRESS THIS
KEY
TO PERFORM THIS ACTION
Play Text-to-Speech message again.
Keep Text-to-Speech message.
Delete Text-to-Speech message.
Exit the menu.
PLAYING A TEXT-TO-SPEECH MESSAGE
To play a Text-to-Speech message
1.
After accessing the Message System Choice menu, the system will prompt you to either
play your unread email messages or your read email messages.
2.
Select
to play the unread email messages or
to play your read email messages.
The system will begin playback of the message in the following order: subject, sender
name, date, time, and body of message. If the email message contains an attached file,
the system will provide notification that a file attachment is present. The importance of the
email is also indicated.
Once you have listened to the desired email message, you can:
•
Press
to keep the message;
•
Press
to delete the message;
•
Press
to play the message again;
•
Press
to exit from the Message System Choice menu.
Note: Before exiting, the system will play a summary of the total number of voicemail
and email messages remaining in the mailbox.
35
NuPoint UM User Guide
SPEECH AUTO ATTENDANT OPTIONAL FEATURE
The NuPoint Unified Messaging Speech Auto Attendant (SAA) is a speech-enabled application
that allows you to place calls to people quickly and efficiently by speaking their names. In
addition to placing calls by name, you can say a department name or telephone number. An
online tutorial introduces you to the system features, and voice-based help is available to answer
questions.
The Speech Auto Attendant routes incoming calls based on spoken commands. Typically, you
say the name of the person you want to speak to and the system transfers your call to the
requested party. The Speech Auto Attendant also supports up to 15 departments and allows
you to call any of the department numbers or names. See “Making Calls” on page 38 for detailed
calling instructions.
The SAA has the ability to store four numbers per person and provides you with the option to
select which of your phone numbers will be the default Speech Auto Attendant number. Refer
to the Web View Help for instructions on how to configure your default phone number.
The following features are available with the Speech Auto Attendant application:
•
Call by Name: You can place calls to any person in the company directory by saying a
person’s name.
•
Call by Number: You can place calls to any number in the company directory by saying a
phone number (extension).
•
Call by Department: You can place calls to any department in the company directory by
saying a department name.
•
Touchtone (DTMF) Dialing: You can place calls to any number in the company directory
by using the keypad to enter the digits.
•
Universal Commands: You can use several generic voice commands (such as "help" or
"operator") to navigate through the system. See “Universal Voice Commands” on page 37
for more information.
•
Barge-in: You can interrupt a system prompt with a speech or keystroke command. The
Speech Auto Attendant will stop playing the prompt and respond to the command.
Note: Barge-in is an optional feature of the Speech Auto Attendant and must be
enabled on your mailbox. Consult your System Administrator for details.
36
•
Tutorial: The Speech Auto Attendant provides a tutorial which allows you to record your
name (if you are a new user), or use the existing recorded name from your voice mail
system. It also introduces you to the system features.
•
Presence: The Speech Auto Attendant provides the ability to determine and playback the
current presence state of the matched person prior to transferring your call. Presence refers
to the person’s availability in relation to the telephone (ie. busy, away, do not disturb etc.).
The presence status information is for reference only, and thus a call will be transferred no
matter what the presence status of the called party may be.
Note: Presence is an optional feature of the Speech Auto Attendant and must be
enabled on your mailbox. Consult your System Administrator for details.
•
Disambiguation: The Speech Auto Attendant provides the ability to transfer calls to the
operator for multiple directory matches (i.e. two people named "John Doe" in the same
directory). You will be notified of the duplicate names and immediately transferred to the
operator, who will ask for more details in order to transfer your call to the right person.
•
Error Handling: The Speech Auto Attendant responds to an error by instructing you to
retry the command. After two recognition errors, the system will transfer your call to the
operator.
•
Timeout: The Speech Auto Attendant will time out when it detects no speech or DTMF
input. Help prompts will be played to aid you in choosing an action.
SPEAKING TIPS
The Speech Auto Attendant responds to natural speech commands. When you become more
comfortable with the prompts, you can use Barge-in to navigate through the system prompts
more quickly.
When you are speaking to the Speech Auto Attendant, follow the guidelines below:
•
Speak clearly, but don’t shout.
•
Speak at your normal pace, that is, not too slowly and not too quickly.
•
In noisy environments, do not use speaker phones as the background noise will affect the
speech recognition success rate.
•
If you are prompted to confirm a name, answer only "Yes" or "No". If you answer "No", wait
for the system prompt before you state the name again.
•
If the system does not recognize a name, it may be because the name is not programmed
into the system or because your pronunciation of the name is not in the system. Contact
your System Administrator to have the name added or to have the pronunciation corrected.
UNIVERSAL VOICE COMMANDS
The following voice commands are available from anywhere within the Speech Auto Attendant
system:
•
Cancel or Stop: Terminates the current operation.
•
Operator: Transfers your call to the operator.
•
Repeat: Replays the most recent prompt.
•
Help: Plays the list of available help commands.
•
Tutorial: Starts the system tutorial.
•
Auto Attendant: Transfers the call to the Speech Auto Attendant.
37
NuPoint UM User Guide
MAKING CALLS
You can use the Speech Auto Attendant to place calls either with voice commands or digit
dialing.
PLACING A CALL WITH VOICE COMMANDS
The Speech Auto Attendant can call contact names or departments that are programmed in
the company directory by responding to your voice commands.
To place a call using voice commands
1.
Dial the Speech Auto Attendant access number.
2.
When the Auto Attendant answers, say one of the following:
•
the first and last name of the person that you want to call;
•
a department name; or
Note: You can listen to all the department names that are programmed in the system
by speaking the "department" command.
•
3.
a phone number (speak the number one digit at a time).
The system confirms the requested name and then dials the number associated with your
spoken command.
Note: If, after two attempts, the Speech Auto Attendant cannot recognize the name
of the person or department that you are trying to call, you will be routed to the
operator.
4.
If the Presence feature is enabled, the system will also indicate the presence state of the
called party. The presence status information is for reference only, and thus the call will be
transferred no matter what the presence status may be.
PLACING A CALL WITH DIGIT DIALING
The Speech Auto Attendant can call contact names or departments that are programmed in
the company directory by responding to the digits that you press on the keypad.
To place a call using digit dialing
1.
Dial the Speech Auto Attendant access number.
2.
When the Auto Attendant answers, enter the digits to dial on the keypad.
3.
The system confirms the requested number and then dials the digits that you selected.
Note: If, after two attempts, the Speech Auto Attendant cannot recognize the number
of the person or department that you are trying to call, you will be routed to the
operator.
4.
38
If the Presence feature is enabled, the system will also indicate the presence state of the
called party. The presence status information is for reference only, and thus the call will be
transferred no matter what the presence status may be.
CANCELLING A CALL
You can cancel a call in progress in one of two ways.
To cancel a call
•
Say "Cancel" or "No" before the Speech Auto Attendant says "Dialing"; or
•
Press 0 (zero) before the Auto Attendant says "Dialing". This command will cancel the call
and the system will automatically route your call to the operator.
CALLING THE OPERATOR
You can call the operator from anywhere in the system.
To call the operator
•
Say "Operator" or "Zero" at any time; or
•
Dial 0 at any time.
39
NuPoint UM User Guide
SPEECH NAVIGATION OPTIONAL FEATURE
NuPoint UM Speech Navigation is a speech-enabled application that allows you to manage
your mailbox using voice commands. In addition to being able to perform standard tasks such
as play, delete and keep messages, you can transfer to the operator, enter numeric digits, and
exit the system simply by speaking the appropriate commands.
Since you issue commands by speaking them, rather than by pressing buttons on a keypad,
Speech Navigation enables you to operate in hands-free mode. This is useful if you have a cell
phone or similar device configured as an alternate extension on your mailbox.
The following features are available with the Speech Navigation application:
•
Multiple Command Options: Speech navigation supports the concept of aliases so that
up to two different phrases can be used to accomplish the same task. For example, users
can say, “Delete Message” or “Discard Message” to delete a voice message.
•
Barge-In: This feature allows users to interrupt a system prompt with a speech or keystroke
command. The system stops playing the prompt and responds to the command. Barge-in
allows experienced system users to skip quickly through the prompts.
•
Error Handling: Speech Navigation responds to an error by instructing the user to retry
the command. After three recognition errors, the system will play the prompt, "I do not
understand that comma: Please call again," and then disconnect the call.
•
Mailbox Extensions: When Speech Navigation is enabled for a mailbox, it applies all of
the user's extensions, including alternate extensions such as teleworker phones and cell
phones. The enables users to call the message center from remote locations and immediately begin using Speech Navigation commands.
•
Commands: The following commands can be invoked with Speech Navigation: Play Message, Keep/Save Message, Delete/Discard Message, Answer/Reply To Message,
Forward/Give Message, Next Message, Make Message, User Options, Operator, and the
digits zero to nine. In addition, users can leave the system by saying one of the following
commands: Bye, Goodbye, Hang-up, or Quit. See “Entering Voice Commands” on page 41
for more information.
SPEAKING TIPS
The Speech Navigation responds to natural speech commands. When you become more
comfortable with the prompts, you can use Barge-in to navigate through the system prompts
more quickly.
When you are speaking to the Speech Navigation, follow the guidelines below:
40
•
Speak clearly, but don’t shout.
•
Speak at your normal pace, that is, not too slowly and not too quickly.
•
In noisy environments, do not use speaker phones as the background noise will affect the
speech recognition success rate.
•
If the system does not recognize your command, you will be prompted to repeat it. If you
fail three times in a row, the system will play the prompt, "I do not understand that command.
Please call again," and then disconnect the call.
•
The system recognizes North American English only.
UNIVERSAL VOICE COMMANDS
The following Speech Navigation voice commands are available when you are logged into your
mailbox:
•
Operator | Transfer to operator | Attendant | Transfer to attendant:
Transfers you to the operator.
•
Bye | Goodbye | Hang-up | Quit:
Provided that you are not currently recording a message, the system plays a message
summary ("You have x messages. Goodbye."), terminates the call and exits the system.
•
Exit:
Takes you up one level in the menu structure.
ENABLING SPEECH NAVIGATION
After your administrator has enabled Speech Navigation for your mailbox, you can turn it on
and off from the Web View.
To enable Speech Navigation for your mailbox:
1.
Open the Web View interface in a web browser.
2.
Enter your Mailbox number and Passcode, and then click Submit.
3.
Select the Speech Navigation tab.
4.
Click Enable Speech Navigation.
Speech Navigation is "turned on" for your mailbox’s primary and alternate extensions.
Note: After you enable Speech Navigation, you will receive prompts only in North
American English, even if your mailbox is configured to use non-English prompts.
ENTERING VOICE COMMANDS
You can use the Speech Navigation voice commands to access your mailbox and manage
messages. Some submenus require the digit dialing.
ACCESSING YOUR MAILBOX
The method to access your mailbox varies depending on whether you are calling from one of
your extensions or from an external number.
From Your Own Extension (Primary or Alternate)
To access your mailbox from your primary extension or one of your alternate extensions:
41
NuPoint UM User Guide
1.
Dial the NuPoint UM Voice access number.
2.
Say your passcode when prompted. (For higher security, enter your passcode with the TUI.)
From an External Number
To access your mailbox from an external number (not one of your extensions):
1.
Dial the NuPoint UM Voice access number.
2.
Enter your mailbox number on the keypad, followed by the
3.
Enter your passcode on the keypad when prompted.
key.
ACCESSING THE VOICE MAIL AND EMAIL MENUS
After you access your mailbox, the system tells you how many messages you have and prompts
you to begin entering Speech Navigation voice commands. The available commands vary
depending on whether you are a regular or Advanced UM voicemail user.
If You Are a Regular Voicemail User
If you are a regular voice mail user, you are already in the Voice Mail menu, so you will hear a
message similar to this: "You have 2 urgent messages and 2 unplayed messages. You may
say Play to play the first message, New Message to make a new message, User Options to
go to User Options..."
•
Proceed to “Managing Your Messages” on page 42.
If You Are Advanced UM Voicemail User with TTS
If you have the Advanced UM with TTS feature, you will hear a message similar to this: "You
have 2 unplayed messages, 1 saved message, 3 unplayed emails, and 1 saved email message.
Say Voicemail to access your voicemail messages; say Email to access your email messages."
1.
Say Voicemail to access the Voice Mail menu or Email to access the Email menu.
2.
Proceed to “Managing Your Messages” on page 42.
Note: Advanced UM users who do not have the TTS option cannot access the email
menu.
MANAGING YOUR MESSAGES
After you have accessed the Voicemail or Email menu, you can manage your messages with
the following Speech Navigation voice commands.
At any time during message playback you can use the telephone user interface to pause the
message, move forward or backward five seconds, skip to the next message or return to the
beginning of the previous message. For details concerning which keys (or softkeys) to press,
see page 7.
Note that some commands, such as Give Message and Answer Message, lead to submenus
that require the digit dialing on the telephone keypad.
42
SAY
TO PERFORM THIS ACTION
Play
Plays the message. Your urgent messages will be played first.
Then, depending on your mailbox settings, you may have the
option to play unplayed or saved messages first; otherwise, your
unplayed messages will be played first.
Play Message
EQUIVALENT
KEY
To replay a message, say "Play" again.
Keep
Keep the message.
Keep Message
Kept messages can be accessed only after you have skipped
through your unplayed messages and message receipt queues.
Save
Save Message
Next
Next Message
Delete
Discard the message.
Delete Message
The system will ask, "Are you sure you want to delete the
message?” Say Yes to confirm the deletion.
Discard
Discard Message
Answer
Answer Message
Answer the person who sent the message using one of the
following options:
• Press
to answer with a voice mail message.
• Press
to dial the caller and keep the message.
• Press
to dial the caller and discard the message.
43
NuPoint UM User Guide
EQUIVALENT
KEY
SAY
TO PERFORM THIS ACTION
Give
Give To
Give one of your voice messages to another mailbox, distribution
list, or off-system telephone number.
Give Message
1. Say or enter the mailbox, distribution list or telephone number.
Forward
2. Say Record, add your comments, and then select one of the
following options:
Forward Message
• Say Review or press
• Say Send or press
to review the message.
to send the message.
• Say Discard or press
to discard the message.
• Say Append or press
to add another comment.
• Say Options or press
options:
to access message addressing
- Say Mark Confidential or press
message as confidential.
- Say Request Receipt or press
return receipt.
- Say Make Urgent or press
message as urgent.
to mark the
to receive a
to mark the
- Say Make Future Delivery or press
to deliver
the message up to 60 days in the future. Then
follow the prompts to specify a date and time.
44
EQUIVALENT
KEY
SAY
TO PERFORM THIS ACTION
Make
Make a new voice message and address it to another mailbox,
distribution list, or off-system telephone number.
Make Message
1. Say or enter the mailbox, distribution list or telephone number.
2. Say Record, add your comments, and then select one of the
following options:
• Say Review or press
• Say Send or press
to review the message.
to send the message.
• Say Discard or press
to discard the message.
• Say Append or press
to add another comment.
• Say Options or press
options.
to access message addressing
- Say Mark Confidential or press
message as confidential.
to mark the
- Say Request Receipt or press
return receipt.
- Say Make Urgent or press
message as urgent.
to receive a
to mark the
- Say Make Future Delivery or press
to deliver
the message up to 60 days in the future. Then
follow the prompts to specify a date and time.
User Options
Allows you to listen to the user tutorial, change your greetings,
record your name, and define your password, create voice mail
distribution lists, and select call scheduling options.
• Say Change Greeting or press
conditional or extended greeting.
• Say Change Name or press
to update your primary,
to re-record your name.
• Say Change Passcode or press
mailbox passcode.
to change your
• Say Change Distribution List or press
distribution lists.
to manage your
• Say Change Call Schedule Options or press
manage your call schedule options.
• Say Activate Tutorial or press
tutorial.
to
to play the system
45
NuPoint UM User Guide
SAY
TO PERFORM THIS ACTION
Exit
Takes you up one level in the menu structure.
Bye
Provided that you are not currently recording a message, the
system plays a message summary ("You have x messages.
Goodbye."), terminates the call and exits the system.
Goodbye
Hang up
EQUIVALENT
KEY
Quit
Note: You may not have access to all of the options above, depending on how your
mailbox is configured. Consult your System Administrator for more information.
ACCESSING OTHER MENUS
Although Speech Navigation is optimized to enable you to manage your voice and email
messages, you can also use it to manage a number mailbox options. However, once you access
the submenus for these options, you must use the telephone keypad rather than voice
commands to make selections. The following submenus require telephone keypad commands:
46
•
Make Future Delivery (under Make Message > Options and Give Message > Options)
•
Change Greeting (under User Options)
•
Distribution List (under User Options)
© Copyright 2017, Mitel Networks Corporation. All Rights Reserved.
The Mitel word and logo are trademarks of Mitel Networks Corporation.
Any reference to third party trademarks are for reference only and Mitel makes no representation of the ownership of these marks.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising