Zinsser 249021, 249020, 249019 User manual

Zinsser 249021, 249020, 249019 User manual
TECHNICAL DATA
BEY-04
BULLS-EYE®
ZERO™
.DESCRIPTION AND USES
®
®
PRODUCT APPLICATION
.
SURFACE PREPARATION
™
Zinsser Bulls-Eye Zero is a high performance, ecofriendly water-based primer for interior and exterior
applications. This product has been formulated to meet
clean air regulations to provide a fast drying, low odor
primer/sealer with excellent adhesion, enamel holdout and
stain blocking properties.
Surfaces should be clean, dry, sound and free of any
contamination, mildew, rust or unsound coatings that may
interfere with adhesion. Remove loosely adhered or
unsound coatings. Sand any remaining paint film edges
smooth. If unsure of cleanliness, always wash surface with
household ammonia and water solution, appropriate
cleaning solution or solvent (do not use TSP as a cleaner).
Rinse the surface thoroughly and allow to dry before
application of the primer. Spot prime knots and sap
streaks with Zinsser B-I-N Primer/Sealer.
Bulls-Eye Zero delivers the performance of oil-based
primers with none of the odors or solvents that contribute
to poor air quality. Bulls-Eye Zero is excellent for use in
residential, institutional or commercial use in schools,
hospitals, hotels, nursing homes, restaurants, etc.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO
LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS
BRAIN DAMAGE, ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH-Approved respirator to
control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National
Lead Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.
Use on interior and exterior new or previously painted
drywall, wood (pine, fir, cedar, redwood, plywood, T-111),
cured plaster, masonry (stucco, cement, poured concrete,
concrete block), hardboard, vinyl, PVC, fiberglass, tile,
Metal (aluminum, steel, galvanized metal). Adheres to
tough surfaces, such as chalky exterior siding and trim,
high gloss enamels, old varnish, tile, galvanized metal and
hardboard.
Seals unpainted porous surfaces, extending the coverage
of the topcoat. Bulls-Eye Zero is an excellent under-coater
for oil or latex enamels, and provides high holdout and
smooth sanding surface necessary to prevent variations in
topcoat gloss.
LIMITATIONS
Bulls-Eye Zero is not recommended for applications to
floors, decks, roof surfaces or any surface subject to
immersion or prolonged contact with water.
Bulls-Eye Zero locks in stains such as residual nail head
dust, asphalt, creosote, tannin bleed for cedar or redwood,
lipstick, crayon, oil, grease, handprints, most ball point and
felt tip pen marks. When priming over bare cedar or
redwood, allow 24 hours dry time before painting.
Persistent stains may require a second coat.
PERFORMANCE CHARACTERISTICS






APPLICATION
Apply only when air, material, and surface temperatures
are between 50-85ºF (10-29ºC) and the relative humidity
is below 85%. Thoroughly mix to ensure any settled
pigment is re-dispersed before using. In most cases only
one coat is necessary to prime most surfaces. If excessive
absorption occurs over very porous substrates a second
coat may be necessary. Spot priming is recommended
only under high-hiding topcoat finishes. For best results,
prime entire surface before painting.
.
For interior & exterior use
Sticks to all surfaces
Seals common stains
Low odor
Mildew resistant film
Dries in 1 hour
.PRODUCTS
SKU
249019
249020
249021
.
Apply with a synthetic (nylon, polyester or blend) bristle
brush, roller, or airless sprayer. Follow manufacturer's
instructions when using spray equipment. For airless
spraying use a .017" tip at 2000 to 2500 psi. Wear NIOSH
approved respirator and provide adequate ventilation.
.
Description
1-Quart
1-Gallon
5-Gallon
1
Form: GDH-70
Rev.: 053113
TECHNICAL DATA
BULLS-EYE® ZERO™
PRODUCT APPLICATION (cont.)
.
THINNING
Bulls-Eye Zero is formulated to be used without thinning.
If thinning is necessary, add no more than 10 fluid ounces
of clean water per gallon and mix thoroughly. Note that
excessive thinning will hinder stain blocking properties.
TINTING
Bulls-Eye Water-Base may be tinted with up to 2 ounces
of universal colorant per gallon. Tinting the primer toward
the color of the topcoat helps hide in one coat. For mid or
deep tone colors use Bulls-Eye 1-2-3 Deep Tint. Shake or
stir well before using.
DRY TIME
Dries to the touch in 30 minutes, can be recoated in 1
hour. Lower temperatures, higher humidity, and the
addition of tint will prolong dry and cure time. Allow more
time at cooler temperatures.
CLEAN-UP
Clean up spills and paint drips with detergent and warm
water. Wipe up splatters before they dry. If spills or drips
have dried, use denatured alcohol or ammoniated
detergent to soften and remove primer. Wash application
tools in detergent and warm water immediately use.
Follow equipment manufacturer’s directions to clean spray
equipment. Dispose of unused or unwanted product in
accordance with local laws regulating water-based
coatings.
2
Form: GDH-70
Rev.: 053013
TECHNICAL DATA
BULLS-EYE® ZERO™
.PHYSICAL PROPERTIES
.
Physical Properties
BULLS-EYE ZERO
Resin Type
Water-based Acrylic
Pigment Type
Titanium Dioxide
Solvents
Weight
Solids
Water, Glycol Ethers
Per Gallon
10.7 lbs.
Per Liter
1.28 kg
By Weight
49.4%
By Volume
34.4%
Volatile Organic Compounds
0 g/l
Recommended Dry Film
Thickness (DFT) per Coat
1.0-1.5 mils
(25-37.5µ)
Wet Film to Achieve DFT (Unthinned
material)
3.0-4.5 mils
(75-112.5µ)
Theoretical Coverage at
1 mil DFT (25µ)
552 sq.ft./gal.
2
(13.6 m /l)
2
Practical Coverage at
Recommended DFT (assume 15%
material loss)
Dry Times at 70°F
(21ºC) and 50%
Relative Humidity
Approximately 400 sq.ft./gal. (9.8 m /l)
depending on application method
and surface porosity
Touch
30-45 minutes
Recoat
1 hour
Full Cure
2 days
Shelf Life
5 years
Flash Point
>200ºF (93ºC)
MPI Certified
#17, 50, 137, 149
Storage
Store indoors at 40-80°F (4-26°C)
Safety Information
For additional information, see MSDS
The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The
statements of this literature do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use
of our materials are beyond our control, we can guarantee these products only to conform to our standards of quality, and our liability, if any,
will be limited to replacement of defective materials. All technical information is subject to change without notice.
Rust-Oleum Corporation
11 Hawthorn Parkway
Vernon Hills, Illinois 60061
An RPM Company
Phone: 877•385•8155
www.rustoleum.com
Form: GDH-70
Rev.: 053113
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement