Integra DPC-7.9 Blu-ray / DVD Player Owner Manual

Document
DPC-7.9_En.book Page 1 Tuesday, July 22, 2008 4:37 PM
DVD Changer
DPC-7.9
Instruction Manual
DPC-7.9_En.book Page 2 Tuesday, July 22, 2008 4:37 PM
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS
TO RAIN OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING
TO
QUALIFIED
SERVICE
PERSONNEL.
WARNING
AVIS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
Important Safety Instructions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
2
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the
manufacturer.
Use only with the cart, stand, PORTABLE CART WARNING
tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to
avoid injury from tip-over.
S3125A
Unplug this apparatus during lightning storms or
when unused for long periods of time.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
15. Damage Requiring Service
Unplug the apparatus from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
A. When the power-supply cord or plug is damaged,
B. If liquid has been spilled, or objects have fallen
into the apparatus,
C. If the apparatus has been exposed to rain or
water,
D. If the apparatus does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the apparatus to its normal operation,
E. If the apparatus has been dropped or damaged in
any way, and
F. When the apparatus exhibits a distinct change in
performance this indicates a need for service.
16. Object and Liquid Entry
Never push objects of any kind into the apparatus
through openings as they may touch dangerous voltage points or short-out parts that could result in a
fire or electric shock.
The apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases shall be placed on the apparatus.
Don’t put candles or other burning objects on top of
this unit.
17. Batteries
Always consider the environmental issues and follow local regulations when disposing of batteries.
18. If you install the apparatus in a built-in installation,
such as a bookcase or rack, ensure that there is adequate ventilation.
Leave 20 cm (8&quot;) of free space at the top and sides and
10 cm (4&quot;) at the rear. The rear edge of the shelf or
board above the apparatus shall be set 10 cm (4&quot;)
away from the rear panel or wall, creating a flue-like
gap for warm air to escape.
DPC-7.9_En.book Page 3 Tuesday, July 22, 2008 4:37 PM
Precautions
1. Recording Copyright—Unless it’s for personal use
only, recording copyrighted material is illegal without the permission of the copyright holder.
2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact
the dealer from whom you purchased this unit.
3. Care—Occasionally you should dust the unit all over
with a soft cloth. For stubborn stains, use a soft cloth
dampened with a weak solution of mild detergent and
water. Dry the unit immediately afterwards with a
clean cloth. Don’t use abrasive cloths, thinners, alcohol, or other chemical solvents, because they may
damage the finish or remove the panel lettering.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the unit’s rear panel
(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).
5.
6.
7.
8.
9.
The power cord plug is used to disconnect this unit
from the AC power source. Make sure that the plug
is readily operable (easily accessible) at all times.
Preventing Hearing Loss
Caution
Excessive sound pressure from earphones and headphones can cause hearing loss.
Batteries and Heat Exposure
Warning
Batteries (battery pack or batteries installed) shall
not be exposed to excessive heat as sunshine, fire or
the like.
Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands
are wet or damp. If water or any other liquid gets
inside this unit, have it checked by the dealer from
whom you purchased this unit.
Handling Notes
• If you need to transport this unit, use the original
packaging to pack it how it was when you originally bought it.
• Do not leave rubber or plastic items on this unit
for a long time, because they may leave marks on
the case.
• This unit’s top and rear panels may get warm
after prolonged use. This is normal.
• If you do not use this unit for a long time, it may
not work properly the next time you turn it on, so
be sure to use it occasionally.
• When you’ve finished using this unit, remove all
discs and turn off the power.
Installing this Unit
• Install this unit in a well-ventilated location.
• Ensure that there’s adequate ventilation all
around this unit, especially if it’s installed in an
audio rack. If the ventilation is inadequate, the
unit may overheat, leading to malfunction.
10.
11.
12.
• Do not expose this unit to direct sunlight or heat
sources, because its internal temperature may
rise, shortening the life of the optical pickup.
• Avoid damp and dusty places, and places subject
to vibrations from loudspeakers. Never put the
unit on top of, or directly above a loudspeaker.
• Install this unit horizontally. Never use it on its
side or on a sloping surface, because it may cause
a malfunction.
• If you install this unit near a TV, radio, or VCR,
the picture and sound quality may be affected. If
this occurs, move this unit away from the TV,
radio, or VCR.
To Obtain a Clear Picture—This unit is a hightech, precision device. If the lens on the optical
pickup, or the disc drive mechanism becomes dirty
or worn, the picture quality may be affected. To
maintain the best picture quality, we recommend
regular inspection and maintenance (cleaning or
worn part replacement) every 1,000 hours of use
depending on the operating environment. Contact
the dealer from whom you purchased this unit for
details.
Moisture Condensation
Moisture condensation may damage this unit.
Read the following carefully:
Moisture may condense on the lens of the optical
pickup, one of the most important parts inside this
unit.
• Moisture condensation can occur in the following
situations:
– The unit is moved from a cold place to a warm
place.
– A heater is turned on, or cold air from an air
conditioner is hitting the unit.
– In the summer, when this unit is moved from an
air conditioned room to a hot and humid place.
– The unit is used in a humid place.
• Do not use this unit when there’s the possibility
of moisture condensation occurring. Doing so
may damage your discs and certain parts inside
this unit.
If condensation does occur, remove all discs and
leave this unit turned on for two to three hours. By
this time, the unit will have warmed up and any condensation will have evaporated.
Region Numbers—The DVD standard uses region
numbers to control how discs can be played around
the world, the world being divided into six regions.
This unit will only play DVD discs that match its
region number, which can be found on its rear panel
(e.g., 1 ,
).
About this Manual—This manual explains how to
use all of this unit’s functions. Although the DVD
standard offers many special features, not all discs
use them all, so depending on the disc being played,
this unit may not respond to certain functions. See
the disc’s sleeve notes for supported features.
ALL
13.
3
DPC-7.9_En.book Page 4 Tuesday, July 22, 2008 4:37 PM
Precautions—Continued
This unit contains a semiconductor laser system and is
classified as a “CLASS 1 LASER PRODUCT”. So, to
use this model properly, read this Instruction Manual
carefully. In case of any trouble, please contact the store
where you purchased the unit.
To prevent being exposed to the laser beam, do not try
to open the enclosure.
CAUTION:
CLASS 1M VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN. DO NOT VIEW
DIRECTLY WITH OPTICAL INSTRUMENTS.
THIS PRODUCT UTILIZES A LASER. USE OF
CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
The label on the right is applied
on the rear panel.
1. This unit is a CLASS 1 LASER
PRODUCT and employs a laser
inside the cabinet.
2. To prevent the laser from being exposed, do not remove the
cover. Refer servicing to qualified personnel.
For U.S. models
FCC Information for User
CAUTION:
The user changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
For Canadian Models
NOTE: THIS CLASS B DIGITAL APPARATUS
COMPLIES WITH CANADIAN ICES-003.
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
4
Mod&egrave;le pour les Canadien
REMARQUE: CET APPAREIL NUM&Eacute;RIQUE DE
LA CLASSE B EST CONFORME &Agrave; LA NORME
NMB-003 DU CANADA.
Sur les mod&egrave;les dont la fiche est polaris&eacute;e:
ATTENTION: POUR &Eacute;VITER LES CHOCS &Eacute;LECTRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.
For British models
Replacement and mounting of an AC plug on the power
supply cord of this unit should be performed only by
qualified service personnel.
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code:
Blue:
Neutral
Brown: Live
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as
follows:
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or
coloured black.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or
coloured red.
IMPORTANT
The plug is fitted with an appropriate fuse. If the fuse
needs to be replaced, the replacement fuse must
approved by ASTA or BSI to BS1362 and have the same
ampere rating as that indicated on the plug. Check for
the ASTA mark or the BSI mark on the body of the fuse.
If the power cord’s plug is not suitable for your socket
outlets, cut it off and fit a suitable plug. Fit a suitable
fuse in the plug.
For European Models
Declaration of Conformity
We, ONKYO EUROPE
ELECTRONICS GmbH
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the
corresponding
technical standards such as EN60065,
EN55013, EN55020 and EN61000-3-2, -3-3.
GROEBENZELL, GERMANY
K. MIYAGI
ONKYO EUROPE ELECTRONICS GmbH
DPC-7.9_En.book Page 5 Tuesday, July 22, 2008 4:37 PM
Connecting the DPC-7.9 ......................... 18
Before Making Any Connections................18
AV Cables &amp; Connectors............................18
Connecting Your TV or Projector...............19
Connecting an AV receiver .........................20
Connecting a Stereo Amp ...........................20
Connecting a Component with an HDMI
Input.......................................................21
Connecting -compatible Components .........22
Controlling AV Components that are
Out of Range..........................................23
Powering Up &amp; Setting Up the
DPC-7.9 .......................................... 24
Powering Up the DPC-7.9...........................24
First Time Setup ..........................................24
Setting the HDMI ........................................25
Basic Playback ........................................ 26
Loading &amp; Removing Discs........................26
Loading Discs During Playback..................27
Selecting Discs ............................................27
Starting, Pausing &amp; Stopping Playback ......28
Navigating Disc Menus...............................29
Using the Disc Navigation Window............30
Selecting Titles, Chapters &amp; Tracks by
Number ..................................................31
Locating Specific Points in Time ................32
Fast Forward &amp; Reverse..............................33
Frame-by-Frame Playback ..........................33
Slow-motion Playback ................................34
Adjusting the Display Brightness................34
Using JPEG CDs .........................................35
Configuring the DPC-7.9 .........................44
Using the On-screen Setup Menus ............. 45
Picture Menu............................................... 45
Audio Menu ................................................ 47
Language Menu .......................................... 48
Display Menu ............................................. 48
Operating Setting Menu.............................. 49
Initial Setup Menu ...................................... 50
Selecting Other Languages ......................... 50
Language Code List.................................... 51
Troubleshooting ......................................52
Specifications ..........................................56
Connections
18
Getting Started
and Setting up
24
Before Using the DPC-7.9....................... 17
Installing the Remote Controller’s
Batteries .................................................17
Using the Remote Controller.......................17
Basic Playback
26
Controls &amp; Connectors........................... 12
Front Panel ..................................................12
Display ........................................................13
Rear Panel ...................................................14
Remote Controller .......................................15
Advanced Playback.................................37
Repeat Playback ......................................... 37
A–B Repeat Playback ................................. 38
Random Playback ....................................... 38
Memory Playback....................................... 39
Using Last Memory .................................... 40
Selecting Camera Angles............................ 41
Selecting Languages &amp; Audio Formats...... 41
Selecting Subtitles ...................................... 41
Zooming...................................................... 42
Displaying Information............................... 43
Playback
Techniques
37
Introduction ............................................... 6
Supplied Accessories.....................................6
DPC-7.9 Features ..........................................7
Disc Notes .....................................................8
DPC-7.9-related Terminology.....................11
Detailed Settings
44
Precautions................................................ 3
Using Chain Mode...................................... 36
Using Party Mode ....................................... 36
Miscellaneous
information
52
Important Safety Instructions .................. 2
Overview
2
Contents
5
DPC-7.9_En.book Page 6 Tuesday, July 22, 2008 4:37 PM
Introduction
Thank you for purchasing an Integra DPC-7.9
DVD Changer. Read this manual carefully before
using your new DVD Changer. A good understanding of its features and operation will allow you to
achieve optimum performance and enjoyment.
Keep this manual for future reference.
Supplied Accessories
Make sure you have the following accessories:
Remote controller (RC-656DV) &amp; 2 batteries (AA/R6)
AV connecting cable (RCA/phono) (1.5 m)
cable (0.8 m)
This cable is used to connect the DPC-7.9 to other
compatible Integra/Onkyo components for
(Remote Interactive) control.
connection, you must
To use
, in addition to an
make an analog audio connection (RCA) between the
DPC-7.9 and your Integra/Onkyo AV receiver.
Coaxial digital cable (1.0 m)
Power cord
(Power cord varies from country to country.)
In catalogs and on packaging, the letter at the end of the product
name indicates the color. Specifications and operation are the
same regardless of color.
6
DPC-7.9_En.book Page 7 Tuesday, July 22, 2008 4:37 PM
Introduction—Continued
DPC-7.9 Features
Highlights
•
•
•
•
•
•
•
•
•
HDMI output with 1080p upscaling
Dolby*1 Digital and DTS Digital Out*2
Holds up to six discs
Chain mode for successive disc playback
Party mode plays discs in random order
DVD-Video playback
Audio CD playback
MP3/WMA*3 playback with on-screen display
JPEG picture display and slideshow (with HD JPEG
resolution via HDMI)
• CD-R, CD-RW (Audio CD, MP3/WMA/JPEG)
• DVD-R/RW, DVD+R/RW (DVD-Video, MP3/WMA/
JPEG)
• Vector Linear Shaping Circuitry*4
• Fast forward and reverse
• Repeat playback options include: Chapter, Title, 1
Disc, All Discs, Track, and Folder (MP3/WMA)
• Random playback options include: Title, 1 Disc, All
Discs, and Folder (MP3/WMA)
• Supports up to 8 soundtracks/languages
• Supports up to 32 subtitle languages
*1.
Manufactured under license from Dolby Laboratories. Dolby
and the double-D symbol are trademarks of Dolby Laboratories.
*2.
Manufactured under license under U.S. Patent #’s: 5,451,942 &amp;
other U.S. and worldwide patents issued &amp; pending. DTS and
DTS Digital Out are registered trademarks and the DTS logos
and Symbol are trademarks of DTS, Inc. All rights reserved.
Video
•
•
•
•
•
•
•
•
•
•
•
•
480i video output by advanced scaling devices
Advanced 108 MHz/14-bit video D/A converter
HDMI*5 digital interface
Component video output
S-Video and composite video outputs
Title, chapter, track, or time search
Last Memory function allows you to resume playback
from a specific point on a DVD-Video disc, even if
that disc has been removed from the DPC-7.9
Supports 4:3 and 16:9 aspect ratio TVs
View mode (Normal/View mode 1/2/3)
Multiple camera angle support
Parental Lock function
Screen Saver function
Audio
• Digital/analog isolated circuit layout to reduce digital
noise
• Audiophile-class performance
• Dynamic Range Control setting
• 192 kHz/24-bit D/A converter
• Coaxial digital output
• Optical digital output
• Analog output
*3. Windows Media, and the Windows logo are trademarks, or
registered trademarks of
Microsoft Corporation in the
United States and/or other countries.
*4.
VLSC and the VLSC logo are registered trademarks of Onkyo
Corporation.
*5.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC.
*6
RIHD is a trademark of Onkyo Corporation.
• Niles is a registered trademark of Niles Audio Corporation.
• Xantech is a registered trademark of Xantech Corporation.
Others
•
•
•
•
•
•
•
Onkyo RIHD*6 system control
Ultra-quiet loading mechanism
Load discs without stopping playback
Program playback (32 tracks, Title, Chapter)
Zoom function
Adjustable display brightness
Slow motion playback
7
DPC-7.9_En.book Page 8 Tuesday, July 22, 2008 4:37 PM
Introduction—Continued
• Don’t use discs with an unusual shape, such as those
shown below, because you may damage the DPC-7.9.
Disc Notes
Supported Discs
The DPC-7.9 supports the following discs.
Disc
Logo
Format or file type
DVD-Video
*1
DVD-R*2
DVD-Video, MP3,
WMA, JPEG
DVD-RW*2
DVD-Video, MP3,
WMA, JPEG
Audio CD*3
PCM
CD-R*2
Audio CD, MP3, WMA,
JPEG
CD-RW*2
JPEG CD
Audio CD, MP3, WMA,
JPEG
JPEG
– DVD+R/RW –
The DPC-7.9 supports DVD+R/RW discs recorded in
the following formats:
• Discs recorded in DVD-Video mode.
• Discs recorded in ISO 9660 Level 2 or Joliet format containing MP3, WMA, or JPEG files.
*1 The Australian model will play PAL and NTSC DVD-Video
discs. When set to AUTO, PAL and NTSC video is output as it
is. When set to PAL, only PAL video is output. When set to
NTSC, only NTSC video is output.
*2 MP3, WMA, and JPEG files are supported on discs recorded in
ISO 9660 Level 2 or Joliet format. (See “MP3/WMA/JPEG
Compatibility” on page 9 for more details.) However, some
CD-R, CD-RW, DVD-R, and DVD-RW discs may not work
properly for any of the following reasons: incomplete disc
finalization, disc burner characteristics, disc characteristics, the
disc is damaged or dirty, the total size of the data is too small.
See the manual supplied with your disc burner for more information. Condensation or dirt on the optical pickup lens can also
affect playback.
*3 Some audio CDs feature copy protection that doesn’t conform
to the official CD standard. Since these are nonstandard discs,
they may not play properly in the DPC-7.9.
• The DPC-7.9 supports DVD-R/+R dual layer discs.
• The DPC-7.9 does not support disc types not listed.
• The DPC-7.9 supports 8 cm and 12 cm discs.
8
• Don’t use discs that have residue from adhesive tape,
rental discs with peeling labels, or discs with custommade labels or stickers. Doing so may damage the
DPC-7.9 and you may not be able to remove the disc
properly.
About playing copy-controlled CDs
Some copy-controlled CDs may not conform to official
CD standards. They are special discs and may not play
on the DPC-7.9.
DVD Region Numbers
1
The North American DPC-7.9 supports only
Region 1 DVD-Video discs bearing this logo.
4
The Australian DPC-7.9 supports only Region 4
DVD-Video discs bearing this logo.
If you attempt to play a disc intended for another region,
a message saying that the disc cannot be played appears.
Function Support
The following icons are used throughout this manual to
indicate which functions can be used with the various
disc formats and file types.
Icon
Disc format or file type
DVD
DVD-Video
CD
Audio CD
MP3
MP3 file
WMA
WMA file
JPEG
JPEG file
About this Manual
This manual explains how to use all of the DVD player’s
functions. Although the DVD standard offers many special features, not all discs use them all, so depending on
the disc being played, the DVD player may not respond
to certain functions. See your disc’s sleeve notes for supported features.
When you attempt to use a DVD feature that is
not available, this logo may appear on-screen,
indicating that the feature is not supported by
the current disc or by the DVD player.
DPC-7.9_En.book Page 9 Tuesday, July 22, 2008 4:37 PM
Introduction—Continued
Disc Content Organization
MP3/WMA/JPEG Compatibility
■ DVD-Video Format
DVD-Video discs contain titles, which are usually subdivided into chapters.
• The DPC-7.9 can play/display MP3, WMA, and JPEG
files recorded on CD-R, CD-RW, DVD-R, DVD-RW,
DVD+R and DVD+RW discs.
• Discs must be in ISO 9660 Level 2 or Joliet format
(folders can be up to eight levels deep). Music files
recorded on discs that use the HFS (hierarchical file
system) cannot be played.
• Discs must be finalized.
• The DPC-7.9 can only recognize the first session on
multisession discs.
• You can determine the order in which the DPC-7.9
plays/displays your MP3/WMA songs and JPEG pictures by prefixing file and folder names with a threedigit number. For example 001.Root, 002.Folder, and
so on, and 001.Track.mp3, 002.Track.mp3, and so on.
• Only the first eight characters of folder and track names
(excluding the filename extension) are displayed.
• The folder numbered “001” appears as “ROOT” in the
Disc Navigator.
• The DPC-7.9 supports up to 255 folders and up to 255
files per folder.
• If you try to play an incompatible file, the message
“This format cannot be played” appears on the display.
Title 1
Chapter 1
Chapter 2
Title 2
Chapter 1
Chapter 2
DVD-Video
■ Audio CD Format
Audio CDs contain tracks.
Track 1
Track 2
Track 3
Track 4
Track 5
Audio CD
■ MP3/WMA Files
MP3 and WMA files are typically organized into folders.
The DPC-7.9 handles MP3 and WMA files as tracks.
Track 1
Folder 1
Track 2 Track 3
Folder 2
Track 1 Track 2
MP3/WMA
(CD-R/CD-RW/DVD-R/DVD-RW/
DVD+R/DVD+RW)
■ JPEG Files
JPEG picture files are typically organized into folders.
The DPC-7.9 handles JPEG files as tracks.
Track 1
Folder 1
Track 2 Track 3
Folder 2
Track 1 Track 2
JPEG
(CD-R/CD-RW/DVD-R/DVD-RW/
DVD+R/DVD+RW)
■ MP3
• MP3 files must be MPEG1 Audio Layer 3 format, 44.1
or 48 kHz, fixed bit-rate.
• MP3 files must have a “.mp3” or “.MP3” filename
extension.
• Variable bit-rates (VBR) from 64 kbps to 320 kbps are
supported. (Playing times may display incorrectly
with VBR.)
■ WMA
• WMA files must have the copyright option turned off.
• Sampling rates 44.1/48 kHz are supported.
• Variable bit-rates (VBR) from 48 kbps to 192 kbps are
supported. (Playing times may display incorrectly
with VBR.)
• WMA files must have a “.wma” or “.WMA” filename
extension.
■ JPEG
• JPEG files must have a “.jpg” or “.JPG” filename
extension.
• JPEG files must be less than 5 megabytes in size.
About WMA
WMA is an acronym for Windows Media Audio and
refers to an audio compression technology developed by
Microsoft Corporation. WMA content can be encoded
by using Windows Media&reg; Player version 7, 7.1 or 8.
9
DPC-7.9_En.book Page 10 Tuesday, July 22, 2008 4:37 PM
Introduction—Continued
Handling Discs
Copyright
• Never touch the underside of a disc. Always hold discs
by the edge, as shown.
It is forbidden by law to copy, broadcast, show, broadcast
on cable, play in public, or rent copyrighted material
without permission.
DVD-Video discs are copy-protected, and any recordings made from these discs will be distorted.
Underside
• Never attach adhesive tape or sticky labels to discs.
Cleaning Discs
• For best results, keep your discs clean. Fingerprints
and dust can affect the sound and picture quality and
should be removed as follows. Using a clean soft
cloth, wipe from the center outwards, as shown. Never
wipe in a circular direction.
✔
• To remove stubborn dust or dirt, wipe the disc with a
damp soft cloth, and then dry it with a dry cloth.
• Never use solvent-based cleaning fluids, such as thinner or benzine, commercially available cleaners, or
antistatic sprays intended for vinyl records, because
they may damage the disc.
Storing Discs
• Don’t store discs in places subject to direct sunlight, or
near heat sources.
• Don’t store discs in places subject to moisture or dust,
such as in a bathroom or near a humidifier.
• Always store discs in their cases and vertically. Stacking, or putting objects on unprotected discs may cause
warping, scratches, or other damage.
10
This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by
Macrovision Corporation and other rights owners. Use
of this copyright-protection technology must be authorized by Macrovision Corporation, and is intended for
home and other limited viewing uses only, unless otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
DPC-7.9_En.book Page 11 Tuesday, July 22, 2008 4:37 PM
Introduction—Continued
DPC-7.9-related Terminology
■ CD-R (Compact Disc Recordable): A type of
CD that can be recorded only once. Can be used to
make audio CDs, or MP3/WMA/JPEG discs.
■ CD-RW (Compact Disc Rewritable): A type of
CD that can be recorded many times. Can be used to
make audio CDs, MP3/WMA/JPEG discs.
■ Chapter: Titles on DVD-Video discs can be subdivided into chapters.
■ Component video: A video connection format
that separates the luminance (Y) and color difference
signals (PR, PB), providing better picture quality than
S-Video.
■ Composite video: A video connection format that
mixes the luminance and color signals together.
■ Dolby Digital: The multi-channel digital surround
sound format used on most DVD-Videos.
■ Downmixing: The process of mixing multiple
audio channels into fewer channels. For example, a
surround mix can be downmixed into two channels
for reproduction on stereo systems.
■ Downsampling: The process of reducing the sampling rate of digital audio.
■ DTS (Digital Theater System): The surround
format that uses less compression for faithful reproduction.
■ DVD-R (DVD Recordable): A type of DVD disc
that can be recorded only once. Can be used to make
DVD-Video discs or to store computer data.
■ DVD-RW (DVD Rewritable): A type of DVD disc
that can be recorded many times. Can be used to
make DVD-Video discs or to store computer data.
■ DVD-Video: The format for storing movies on
DVD, with interactive menus, multiple language
soundtracks, subtitles, camera angles, and so on.
■ Field: In interlaced scanning, a field is a single scan
of the screen. There are two fields per frame.
■ Frame: An individual TV picture is called a frame.
With the NTSC color system there are 30 frames per
second.
■ HD: Abbreviation for high definition, as in
HDTV(high-definition TV).
■ HDCP (High-bandwidth Digital Content
Protection): The video encryption technology
developed by Intel for HDMI/DVI. It’s designed to
protect video content and requires a HDCP-compatible device to display the encrypted video.
■ HDMI (High Definition Multimedia Interface):
A new connection format that greatly simplifies AV
connections by carrying uncompressed SD or HD
digital video and digital audio all in one cable.
■ Interlaced scanning: TV pictures are made by
scanning the screen in horizontal lines from top to
bottom. With Interlaced scanning, two scans (fields)
are used to make each picture (frame). Contrast with
Progressive scanning.
■ JPEG (Joint Photographic Experts Group):
The compressed file format used to store digital photos.
■ LFE (Low-Frequency Effects): The surroundsound channel used for low-frequency effects.
■ Linear PCM: The uncompressed digital audio format used for audio CDs. PCM stands for Pulse Code
modulation.
■ MP3 (MPEG 1 Audio Layer 3): Popular compressed file format for storing digital music.
■ MPEG1 (Moving Picture Experts Group 1):
The compressed digital video format used for Video
CDs.
■ MPEG2 (Moving Picture Experts Group 2):
The compressed digital video format used for
DVD-Videos, offering better picture quality than
MPEG1.
■ NTSC: The color TV system used in the United
States, Japan, Taiwan, and Korea.
■ PAL: The color TV system used in most of Europe,
the United Kingdom, Australia, Brazil, and China.
■ Progressive scanning: TV pictures are made by
scanning the screen in horizontal lines from top to
bottom. With progressive scanning, each picture
(frame) is made by scanning the entire screen in one
go, resulting is a clearer and stabler picture. Contrast
with Interlaced scanning.
■ RIHD (Remote Interactive over HDMI):
Onkyo’s implementation of CEC (Consumer Electronics Control), which allows integrated system
control over HDMI and is part of the HDMI standard.
■ S-Video: A video connection format that separates
the luminance (Y) and color (C) signals, providing
better picture quality than composite video.
■ Title: Movies on DVD-Video are called titles.
■ WMA (Windows Media Audio): A compressed
file format for storing digital music.
11
DPC-7.9_En.book Page 12 Tuesday, July 22, 2008 4:37 PM
Controls &amp; Connectors
Front Panel
A
B
7
C456
K
8
9
J
M NOPQ R S
L
The page numbers in parentheses show where you can find the main explanation for each item.
A On/Standby button (24)
This button is used to set the DPC-7.9 to On or
Standby.
Don’t turn on the power until you’ve completed,
and double checked all connections.
B Standby indicator (24)
This indicator lights up when the DPC-7.9 is in
Standby mode.
C Random button (38)
This button is used with the Random function.
D Repeat button (37)
This button is used with the Repeat function.
E Dimmer button (34)
This button is used to adjust the display brightness
and turn the disc tray light on or off.
F Display button (43)
This button is used to display information about the
current disc, title, chapter, or track, including the
elapsed time, remaining time, total time, and so on.
G Display
See “Display” on page 13 for more information.
H Remote control sensor (17)
This sensor receives control signals from the remote
controller.
I Open/Close button (25, 26, 27)
This button is used to open and close the disc tray.
J Disc Select 1–6 buttons (27)
These buttons are used to select discs. Playback
starts automatically when a disc is selected with
these buttons.
12
K Disc tray (26)
The disc tray has six bays for loading up to six
discs.
L Disc tray light
This light illuminates the disc tray. It comes on
when the DPC-7.9 is turned on, and is brighter
while the disc tray is open.
M Disc Skip button (26, 27)
This button is used to select the disc bays (i.e.,
rotate the disc tray) when loading or removing
discs, and to select discs for playback.
N Down [
] button (28, 30, 31, 35)
This button is used to select the previous chapter or
track. During playback it selects the beginning of
the current track.
O Up [
] button (28, 30, 31, 35, 38)
This button is used to select the next chapter or
track.
P Party Mode button (36)
This button is used with the Party mode function.
Q Pause button (28)
This button is used to pause playback.
R Stop button (28)
This button is used to stop playback and to cancel
Party mode.
S Play button (28)
This button is used to start playback and to cancel
fast forward and fast reverse.
DPC-7.9_En.book Page 13 Tuesday, July 22, 2008 4:37 PM
Controls &amp; Connectors—Continued
Display
1
2
CHAIN MODE DISC
ALL
DVD
CD
3
TITLE
4 5
6 7 8 9 0A B
CHP
PRGV
TRACK
LAST
TOTAL
REMAIN
CDVD
D
E
C
1
2
3
4
5
6
F
The page numbers in parentheses show where you can find the main explanation for each item.
1 CHAIN MODE, ALL, DVD &amp; CD indicators
(36)
The CHAIN MODE indicator appears when the
Chain mode function is on. The ALL, DVD, and CD
indicators show the type or Chain mode selected.
When Party mode is selected, the CHAIN MODE
and CD indicators appear.
2 DISC indicator
The number of the currently selected disc appears
here.
3 TITLE indicator
While stopped, the total number of titles on the current DVD-Video disc is displayed here. During
playback, the number of the current title is displayed.
4 CHP indicator
This indicator appears while the number of the current chapter is being displayed.
5 TRACK indicator
This indicator appears while track numbers are
being displayed. While stopped, the total number of
tracks on the current audio CD, or MP3/WMA disc
are displayed. During playback, the number of the
current track is displayed.
6 PRGV indicator
This indicator appears when the component video
output is outputting progressive video. While the
indicator is shown, nothing is output by the other
video outputs.
7 LAST indicator (40)
This indicator appears when the Last Memory function has been set.
9 REMAIN indicator
This indicator appears while the remaining time is
being displayed.
0 Camera angle
indicator (41)
This indicator appears if the DVD-Video disc being
played features multiple camera angles.
A Play
indicator (28)
This indicator is shown during playback.
B Pause
indicator (28)
This indicator appears when playback is paused.
C Disc indicators 1–6 (26)
These indicators show how many discs are loaded.
The number of the current disc has a circle around
it.
When the disc tray is closed, all of the disc indicators appear until the DPC-7.9 has checked each bay
for the presence of a disc. If a bay is found to have
no disc, the corresponding indicator disappears.
D Chapter &amp; track number
Chapter and track numbers appears here.
E Time display
Time information, such as total time, remaining
time, and so on, is displayed here in hours, minutes,
and seconds. Other messages are also displayed.
F CDVD indicator
This indicator shows the type of disc currently
selected:
DVD: DVD-Video, DVD-R, DVD-RW, DVD+R, or
DVD+RW
CD: Audio CD, MP3/WMA/JPEG CD-R, or
CD-RW
8 TOTAL indicator
This indicator appears while the total time is being
displayed.
13
DPC-7.9_En.book Page 14 Tuesday, July 22, 2008 4:37 PM
Controls &amp; Connectors—Continued
Rear Panel
1
4
2
5
3
67 8
9 J K
A RS 232
This port is for servicing.
B IR IN/OUT (23)
The IR IN connector can be used to connect a commercially available IR receiver, which can be used
to pickup signals from the remote controller when
the DPC-7.9 is located in another room, installed in
a rack, or is out of range of the remote controller
The IR OUT connector can be used to connect a
commercially available IR emitter, which can be
used to pass remote controller signals received by
the IR IN along to other AV components.
C COMPONENT 2 VIDEO OUTPUT
These BNC connectors can be used to connect a TV
or projector with BNC component video inputs.
The DPC-7.9 has two component video outputs, the
COMPONENT 1 and COMPONENT 2, however,
they output the same video signal.
D ANALOG AUDIO OUTPUT
These RCA/phono connectors can be connected to
the analog audio inputs on your TV, hi-fi amp, AV
receiver. There are two sets of outputs. You could
connect one set to your AV receiver, the other to your
TV for those occasions when you want to watch a
DVD-Video but don’t want to use your AV receiver.
The DPC-7.9 has two pairs of stereo analog audio
output connectors. They output the same audio signal respectively.
E
REMOTE CONTROL
These
(Remote Interactive) connectors can be
connected to the
connectors on your other Integra/Onkyo AV components for interactive control.
If you’re using RIHD, do not connect anything to
these connectors.
F OPTICAL AUDIO OUTPUT
This optical digital audio output can be connected to
an optical digital audio input on a hi-fi amp, AV
receiver, or surround sound decoder (Dolby Digital,
DTS).
14
L
G COAXIAL AUDIO OUTPUT
This coaxial digital audio output can be connected
to a coaxial digital audio input on a hi-fi amp, AV
receiver, or surround sound decoder (Dolby Digital,
DTS).
H HDMI OUT
This HDMI jack outputs digital video and audio and
can be connected to an HDMI input on a compatible
TV or other component.
I S VIDEO OUTPUT
These connectors can be used to connect TVs or
projectors with S-Video inputs.
The DPC-7.9 has two S-Video output connectors.
They output the same video signal.
J VIDEO OUTPUT
These RCA/phono connectors can be used to connect TVs or projectors with composite video inputs.
The DPC-7.9 has two composite video output connectors. They output the same video signal respectively.
K COMPONENT 1 VIDEO OUTPUT
These RCA/phono connectors can be used to connect a TV or projector with RCA/phono component
video inputs.
The DPC-7.9 has two component video outputs, the
COMPONENT 1 and COMPONENT 2, however,
they output the same video signal.
L AC INLET
The supplied power cord connects to this polarized
inlet. The other end of the power cord should be
connected to a suitable wall outlet. On the Australian model, the power cord is not polarized.
See page 19–22 for connection information.
DPC-7.9_En.book Page 15 Tuesday, July 22, 2008 4:37 PM
Controls &amp; Connectors—Continued
Remote Controller
The page numbers in parentheses show where you can
find the main explanation for each item.
A On button (24)
1
2
This button is used to turn on the DPC-7.9.
Don’t turn on the DPC-7.9 until you’ve completed,
and double checked all connections.
P
Q
B Standby button (24)
R
C Number buttons (31, 32, 39, 49)
This button is used to set the DPC-7.9 to Standby.
S
3
T
U
4
5
6
W
X
Y
7
8
9
J
V
Z
These buttons are used to enter title, chapter, and
track numbers and to enter times for locating specific points in time.
To enter a single-digit number, simply press the corresponding button. To enter a double-digit number,
enter the numbers in order from left-to-right (e.g., to
enter 14, press [1] then [4].
The [+10] button is used to enter multiples of ten
(i.e., 10, 20, 30, and so on). For example, to enter
the number 25, press the [+10] button twice followed by the [5] button.
D Audio button (29, 41)
a
b
c
This button is used to select foreign language
soundtracks and audio formats (e.g., Dolby Digital
or DTS).
E Subtitle button (29, 41)
This button is used to select subtitles.
K
d
F Random button (38)
This button is used with the Random Playback function.
G Slow [
L
e
M
N
O
f
g
]/[ ] buttons (34)
These buttons are used for slow motion playback.
H Down [
] button (28, 30, 31, 35)
This button is used to select the previous chapter or
track. During playback it selects the beginning of
the current track.
I Play [ ] button (28)
This button is used to start playback.
J FR [
] button (33)
This button is used to start fast reverse.
K [ ], [ ], [ ], [ ] buttons (29)
These buttons are used to navigate DVD-Video
menus and the on-screen setup menus.
L Top Menu button (29, 35)
This button is used to select the top menu.
M Menu button (29, 35)
This button is used to select the menu.
15
DPC-7.9_En.book Page 16 Tuesday, July 22, 2008 4:37 PM
Controls &amp; Connectors—Continued
N Aspect/Zoom button (42, 46)
This button is used to change the view mode. Pressing and holding it for a few seconds selects Zoom
mode.
O Resolution button (25)
This button is used to set the video resolution of the
HDMI OUT, and to turn the HDMI OUT on or off.
P Open/Close [ ] button (26, 27)
This button is used to open and close the disc tray.
Q Disc Skip [+]/[–] button (26, 27)
This button is used to select the disc bays (i.e.,
rotate the disc tray) when loading or removing
discs, and to select discs for playback.
R Search button (31, 32)
This button is used to search for titles, chapters,
tracks, and specific points in time.
S Memory button (39)
This button is used with the Memory Playback
function.
T Repeat button (37)
This button is used to set the Repeat Playback functions.
U A–B button (38)
This button is used to set the A–B Repeat Playback
function.
V CLR button (40, 49)
This button is used to cancel various functions.
W Display button (43)
This button is used to display information about the
current disc, title, chapter, or track, including the
elapsed time, remaining time, total time, and so on.
X Angle button (41)
This button is used to select different camera angles.
Y Last Memory button (40)
This button is used with the Last Memory function.
Z Pause [ ] button (28, 33)
This button is used to pause playback. For DVDs,
pressing this button while playback is paused moves
the video forward one frame at a time.
a Up [
] button (28, 30, 31, 35)
This button is used to select the next chapter or
track.
b Stop [ ] button (28)
This button is used to stop playback.
c FF [
] button (33)
This button is used to start fast forward.
d Enter button (45)
This button is used to start playback of the selected
title chapter, or track and to confirm settings.
e Setup button (45)
This button is used to open and close the on-screen
setup menus.
16
f Return button (45)
This button is used to return to the previous screen.
g Chain Mode button (36)
This button is used with the Chain mode function.
DPC-7.9_En.book Page 17 Tuesday, July 22, 2008 4:37 PM
Before Using the DPC-7.9
Installing the Remote Controller’s
Batteries
1
Open the battery compartment, as
shown.
Using the Remote Controller
To use the remote controller, point it at the DPC-7.9’s
remote control sensor, as shown below.
Remote control sensor
DPC-7.9
)
30˚
2
3
Insert the two supplied batteries (AA/
R6) in accordance with the polarity diagram inside the battery compartment.
Close the battery compartment.
Notes:
• If the remote controller doesn’t work reliably, try
replacing both batteries.
• Don’t mix new and old batteries, or different types of
batteries.
• If you intend not to use the remote controller for a long
time, remove the batteries to prevent possible leakage
and corrosion.
• Flat batteries should be removed as soon as possible to
prevent possible leakage and corrosion.
5
30˚
.
ox
pr
16
(
ft.
m
Ap
Notes:
• The remote controller may not work reliably if the
DPC-7.9 is subjected to bright light, such as direct
sunlight or inverter-type fluorescent lights. Keep this
in mind when installing the DPC-7.9.
• If another remote controller of the same type is used in
the same room, or the DPC-7.9 is installed close to
equipment that uses infrared rays, the remote controller may not work reliably.
• Don’t put anything, such as a book, on the remote controller, because the buttons may be pressed inadvertently, thereby draining the batteries.
• The remote controller may not work reliably if the
DPC-7.9 is installed in a rack behind colored glass
doors. Keep this in mind when installing the DPC-7.9.
• The remote controller will not work if there’s an obstacle between it and the DPC-7.9’s remote control sensor.
17
DPC-7.9_En.book Page 18 Tuesday, July 22, 2008 4:37 PM
Connecting the DPC-7.9
RCA/phono AV Connection Color Coding
This chapter explains how to connect the DPC-7.9 to
your other AV components.
• Read the manuals supplied with your AV components.
• Don’t connect the power cord until you’ve completed
all audio and video connections.
RCA/phono AV connections are usually color coded:
red, white, and yellow. Use red plugs to connect rightchannel audio inputs and outputs (typically labeled “R”).
Use white plugs to connect left-channel audio inputs and
outputs (typically labeled “L”). And use yellow plugs to
connect composite video inputs and outputs.
Optical Digital Jack
Right (red)
The DPC-7.9’s optical digital jack has shutter-type cover
that open when an optical plug is inserted and close
when it’s removed. Push plugs in all the way.
Left (white)
Caution: To prevent shutter damage, hold the optical
plug straight when inserting and removing.
• Push the plugs in all the way
to make a good connection.
• To prevent interference, keep
audio and video cables away
from power cords and speaker
cables.
Before Making Any Connections
(Yellow)
Analog audio
Right (red)
Left (white)
Composite video
(Yellow)
Right!
Wrong!
AV Cables &amp; Connectors
HDMI connections can carry uncompressed, standard or high definition digital video and digital
audio, for the best picture and sound quality.
HDMI
Video
Component
video
Y
Y
PB
PB
PR
PR
Y
Y
PB
PB
PR
PR
Y
PB
PR
Component video separates the luminance (Y) and
color difference signals (PR, PB), providing the
best picture quality. (Some TV manufacturers
label their component video inputs slightly differently.)
The DPC-7.9 has RCA/phono and BNC component video outputs.
S-Video
S-Video provides better picture quality than composite video.
Composite
video
Composite video can be found on virtually all TVs,
VCRs, and other video equipment. Use only dedicated composite video cables.
Audio
18
Optical
digital
Optical digital audio connections with the optical
digital audio output and a suitable AV receiver,
you can enjoy DVD-Videos with surround sound.
Coaxial
digital
Coaxial digital audio connections with the coaxial
digital audio output and a suitable AV receiver,
you can enjoy DVD-Videos with surround sound.
Analog
RCA/phono analog audio connectors can be found
on virtually all AV components.
DPC-7.9_En.book Page 19 Tuesday, July 22, 2008 4:37 PM
Connecting the DPC-7.9—Continued
Connecting Your TV or Projector
This section explains how to connect the DPC-7.9 to
your TV or projector.
See page 21 for connecting a TV or projector that
supports HDMI.
In this hookup example, the TV handles the audio and
video. To enjoy Dolby Digital or DTS (surround), you’ll
need a compatible decoder (see page 20).
The DPC-7.9 has four types of video output: HDMI,
component video, S-Video, and composite video.
HDMI offers the best picture quality, so if your TV supports it, see page 21. Component video offers the next
best picture quality, so if your TV supports it, use a commercially available component video cable to connect
the DPC-7.9’s COMPONENT VIDEO OUTPUT to the
component video input on your TV. If your TV supports
progressive scanning, you must use component video in
order to take advantage of that feature. S-Video offers
better picture quality than composite video, so if your
TV supports it, use the S-Video cable to connect the
DPC-7.9’s S VIDEO OUTPUT to an S-Video input on
your TV. Failing that, use the supplied composite video
cable to connect the DPC-7.9’s VIDEO OUTPUT to a
composite video input on your TV.
Compatibility of this unit with progressive-scan TVs.
This player is compatible with progressive video Macro
Vision System Copy Guard.
CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY
CAUSE ARTIFACTS TO BE DISPLAYED IN THE
PICTURE. IN CASE OF 525 OR 625 PROGRESSIVE
SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE “STANDARD DEFINITION”
OUTPUT. IF THERE ARE QUESTIONS REGARDING OUR TV SET COMPATIBILITY WITH THIS
MODEL 525p AND 625p DVD PLAYER, PLEASE
CONTACT OUR CUSTOMER SERVICE CENTER.
*1 The DPC-7.9 has two composite
video output connectors and two
pairs of stereo analog audio output
connectors. They output the same
video and audio signals respectively.
*2 The DPC-7.9 has two S-Video output connectors. They output the
same video signal.
*3 The DPC-7.9 has two component
video outputs. The COMPONENT 1
output uses RCA/phono connectors.
The COMPONENT 2 output uses
BNC connectors. They output the
same video signal.
(red)
S-Video cable*2
(white)
Component
video cable*3
(yellow)
IN
Y
AV RCA/
phono cable
(supplied)*1
Only one connection
required! Choose
component video,
S-Video, or
composite video.
PB
PR
(red)
S VIDEO IN
(white)
(yellow)
TV or projector
VIDEO IN
L
R
ANALOG
INPUT
19
DPC-7.9_En.book Page 20 Tuesday, July 22, 2008 4:37 PM
Connecting the DPC-7.9—Continued
Digital Connection
• When the HDMI Output setting is set to On (see
page 46), the DPC-7.9 cannot output progressive
video. To output progressive video, you must set
the HDMI Output setting to Off (see page 46),
and set the Progressive setting to Progressive (see
page 46).
• When the Progressive setting is set to Progressive
so that progressive video is output by the COMPONENT VIDEO OUTPUT, and the PRGV indicator is shown, nothing is output by the VIDEO
(composite video) and S VIDEO (S-Video) outputs. To output video from these outputs, you
must set the Progressive setting to Interlaced (see
page 46).
• The Progressive can also be changed by pressing
and holding the Down [
] button, and then
pressing [On/Standby] button.
Notes:
• Before making any connections, turn off the DPC-7.9
and your TV and disconnect their power cords from
the wall outlets.
• Also refer to the connection information supplied with
your TV.
• Connect the DPC-7.9’s video outputs directly to your
TV. Don’t connect a VCR or other video equipment in
between your DPC-7.9 and TV. Doing so may result in
picture distortion, because of the copy protection system used on DVD-Video discs.
• When you use the analog audio outputs, don’t play
DTS CDs or don’t select DTS soundtracks on
DVD-Video discs. Doing so will produce unpleasant
digital noise, which may damage your equipment.
Connecting an AV receiver
Analog Connection
Use an RCA/phono audio cable to connect the
DPC-7.9’s ANALOG AUDIO OUTPUTs to a pair of
analog audio inputs on your AV receiver, as shown.
Signal flow
To enjoy Dolby Digital or DTS surround sound, you
need to connect one of the DPC-7.9 digital audio outputs
to the digital input on a Dolby Digital or DTS decoder or
an AV receiver with built-in decoders.
Use an optical (or coaxial) digital audio cable to connect
the DPC-7.9’s COAXIAL (or OPTICAL) DIGITAL
AUDIO OUTPUT to an optical (or coaxial) input on
your AV receiver, as shown.
Optical
digital
cable
OPTICAL
OPTICAL
COAXIAL
Coaxial
digital
cable
(supplied)
Connect one or
the other
COA
XIAL
Signal flow
AV component with
Dolby Digital/DTS decoder
Notes:
• Make sure that the Digital/HDMI Audio Out setting
on the Audio menu is set to All (see page 47). Otherwise, you won’t get surround sound.
• Also refer to the connection information supplied with
your AV receiver or decoder.
• When playing Dolby Digital or DTS source material,
be sure to select Dolby Digital or DTS decoding,
respectively, on your AV receiver or decoder. See the
relevant manuals.
• You can experience Dolby Digital only with DVDs
that bear the Dolby Digital logo. Likewise, you can
experience DTS only with DVDs or CDs that bear the
DTS logo.
L
R
(white)
(red)
ANALOG
INPUT
RCA/phono cable
(white)
20
(red)
Connecting a Stereo Amp
This section explains how to connect the DPC-7.9 to a
stereo amp for better sound quality than that of most
TVs. This is ideal for playing your audio CDs and MP3/
WMA discs in the DPC-7.9. DVD-Video discs will
sound better too.
DPC-7.9_En.book Page 21 Tuesday, July 22, 2008 4:37 PM
Connecting the DPC-7.9—Continued
Analog Connection
Use an RCA/phono audio cable to connect the
DPC-7.9’s ANALOG AUDIO OUTPUTs to a pair of
analog audio inputs on your stereo amp, as shown.
converted and output as PCM. DTS signals will not be
output at all.
• Never connect the DPC-7.9 to the AC-3RF input on a
Dolby Digital receiver. The AC-3RF format is not supported by the DPC-7.9.
Signal flow
Connecting a Component with an
HDMI Input
L
R
(white)
(red)
ANALOG
INPUT
This section shows how to connect the DPC-7.9 to an AV
receiver, HDTV, or projector with an HDMI input.
RCA/phono cable
(white)
What is HDMI?
(red)
Note:
• When you use the analog audio outputs, don’t play
DTS CDs or don’t select DTS soundtracks on
DVD-Video discs. Doing so will produce unpleasant
digital noise, which may damage your equipment.
Digital Connection
HDMI (High Definition Multimedia Interface) is a new
connection format that can carry uncompressed, standard or high definition digital video and up to eight channels of digital audio. Until now, several separate video
and audio cables have been required to connect AV components together. With HDMI, a single cable is all that’s
necessary to achieve the best picture and audio quality.
HDMI video is compatible with DVI (Digital Visual
Interface). To send HDMI video to a DVI input requires
an HDMI-to-DVI cable. The DPC-7.9 supports HDCP
(High-bandwidth Digital Content Protection), and for an
HDMI-to-DVI connection to work, the other component
must also support it. Note that this may not work with
some DVI components.
Using HDMI
Use an optical (or coaxial) digital audio cable to connect
the DPC-7.9’s COAXIAL (or OPTICAL) DIGITAL
AUDIO OUTPUT to an optical (or coaxial) input on
your stereo amp, as shown.
Use the HDMI cable to connect the DPC-7.9’s HDMI
OUT to an HDMI input on your AV receiver. Alternatively, you can connect the DPC-7.9 directly to the
HDMI input on your TV.
Signal flow
OPTICAL
COA
XIAL
Connect one or the other
OPTICAL
Optical
digital cable
COAXIAL
Coaxial
digital
cable
(supplied)
Signal flow
HDMI cable
HDMI
IN
HDTV,
projector
or
AV receiver
HDMI
IN
Notes:
• Be sure to set the Audio menu, Digital/HDMI Audio
Out setting to “PCM” (see page 47). Otherwise an
unpleasant digital noise may be heard, which may
damage your equipment.
• When the Audio menu, Digital/HDMI Audio Out setting is set to “PCM,” Dolby Digital signals will be
HDMI
HDMI
IN
HDTV,
projector
21
DPC-7.9_En.book Page 22 Tuesday, July 22, 2008 4:37 PM
Connecting the DPC-7.9—Continued
Notes:
• The DPC-7.9 supports HDCP (High-bandwidth Digital Content Protection), a protection system for digital
video. HDMI components that you connect to the
DPC-7.9 must also support HDCP.
• The DPC-7.9 supports HDMI (High-Definition Multimedia Interface) Specification Information Version
1.0.
Connecting
Components
AV receiver
HDMI &amp; the DPC-7.9
IN
L
■ Video
The DPC-7.9’s HDMI OUT supports the following
video resolutions:
• 720 x 480i 60 Hz
• 720 x 480p 60 Hz
• 720 x 576i 50 Hz (European and Australian models
only)
• 720 x 576p 50 Hz (European and Australian models
only)
• 1280 x 720p 50/60 Hz
• 1920 x 1080i 50/60 Hz
• 1920 x 1080p 50/60 Hz
If the connected HDTV or projector doesn’t support a
resolution, you may get no picture.
On the DPC-7.9, you can select a resolution suitable for
use with the connected HDTV or projector (see
page 25).
■ Audio Formats
The DPC-7.9’s HDMI OUT supports the following
audio formats:
• PCM (48 kHz, 44.1 kHz, 96kHz)
• Dolby Digital
• DTS
If your TV only supports HDMI digital audio up to
48 kHz, change the Linear PCM Out setting to Down
Sample On (see page 47).
If your TV doesn’t support Dolby Digital, set the Digital/
HDMI Audio Out setting to PCM (see page 47).
If your TV doesn’t support DTS, the DPC-7.9 will not be
able to play DTS format audio or soundtracks. In this
case, on your DVD-Video disc’s audio setup menu,
select an audio format other than DTS.
RIHD (CEC)
The DPC-7.9 supports RIHD (Remote Interactive over
HDMI), which is Onkyo’s implementation of CEC
(Consumer Electronics Control), which allows integrated system control over HDMI and is part of the
HDMI standard. In addition to Integra/Onkyo AV components, it allows interoperability with CEC-compatible
AV components and TVs made by other manufacturers.
To use RIHD, make sure that CEC is turned on on your
other components (e.g., TV, AV receiver)
22
-compatible
REMOTE
CONTROL
R
• The remote controller supplied with Integra/Onkyo
AV receiver or amplifiers can be used to control the
DPC-7.9.
• The function of the upper and lower
connectors are
the same. Connect to either one.
• Connecting an
cable only does not make the system operational. You must also connect the audio
cables as well.
• For remote control operation, you must make an analog RCA connection between your DPC-7.9 and the
other AV component, even if they are connected digitally.
• If you’re using RIHD, do not connect anything to the
RI connectors.
DPC-7.9_En.book Page 23 Tuesday, July 22, 2008 4:37 PM
Connecting the DPC-7.9—Continued
Controlling AV Components that are Out of Range
You can use the following multi-room kits to control the
DPC-7.9 when it’s out of range of the remote controller:
• Multiroom kits such as those made by Niles and Xantech.
Controlling Other Out-of-range AV
Components
If another AV component is out of range of its remote
controller, you can use a commercially available IR
emitter to retransmit the remote controller signals
received at the DPC-7.9’s IR IN, as shown below.
Signal flow
IR receiver
Connecting
block
IR IN
IR OUT
DPC-7.9
IR emitter
Controlling the DPC-7.9 When It’s Out of
Range
If the DPC-7.9 is located in another room, installed in a
cabinet, or out of range of its remote controller, you can
use a commercially available IR receiver to pickup the
remote controller signals and feed them to the DPC-7.9,
as shown below.
Connecting
block
Signal flow
IR receiver
Remote controller
Other
component
Connect the IR emitter to the DPC-7.9’s IR OUT, and
place the IR emitter in front of the other AV component’s
remote control sensor (usually located on its front
panel), as shown below. See the instructions supplied
with the IR emitter.
Other component
IR IN
Remote control
sensor
from
connecting block
DPC-7.9
IR emitter
Remote controller
Miniplug cable
Inside
cabinet
Miniplug
Connect the IR receiver to the DPC-7.9 as shown below.
from connecting block
IR Emitter
DPC-7.9
Signal flow
Miniplug cable
Only remote controller signals received by the
DPC-7.9’s IR IN are fed through to the IR OUT. Signals
picked up by the DPC-7.9’s remote control sensor are
not output.
Signal flow
DPC-7.9
23
DPC-7.9_En.book Page 24 Tuesday, July 22, 2008 4:37 PM
Powering Up &amp; Setting Up the DPC-7.9
3
On/Standby
Remote controller
Standby indicator
On
Standby
To turn on the DPC-7.9, press the
[On/Standby] button (or the
remote controller’s [On] button).
The DPC-7.9 comes on, the display
lights up, and the Standby indicator
goes off.
To turn off the DPC-7.9, press the [On/
Standby] button (or the remote controller’s [Standby] button). The DPC-7.9
enters Standby mode and the Standby
indicator comes on.
First Time Setup
The very first time you turn on your DPC-7.9, the Initial
Setup menu appears on-screen, as shown.
Initial Setup
TV Shape
HDMI Output Setting
On-Screen Language
Enter
Powering Up the DPC-7.9
Before connecting the power cord, connect all your AV
components (see page 18 to page 22).
Don’t forget to turn on your TV or projector and select
the video input to which the DPC-7.9 is connected.
If you’re using a hi-fi amp, AV receiver, or surround
sound decoder for audio playback, turn that on as well
and select the audio input to which the DPC-7.9 is connected.
1
Connect the supplied power cord
to the DPC-7.9’s AC INLET.
2
Plug the other end of the power
cord into a suitable wall outlet.
The DPC-7.9 enters Standby mode, and
the Standby indicator comes on.
When you disconnect the power cord,
always disconnect it from the wall outlet first, and then the DPC-7.9’s AC
INLET.
4:3 Letter box
4:3 Pan Scan
16:9 Widescreen
√ 16:9 Compressed
Here you need to specify the size of your TV (standard
4:3 or widescreen 16:9), specify a HDMI output setting,
and select a language for the on-screen setup menus. You
can change these settings later by using the on-screen
setup menus (see page 44).
1
Remote controller
2
Remote controller
3
Remote controller
Use the remote controller’s Up/
Down [ ]/[ ] buttons to select a TV
shape, and then press [Enter].
See page 45 for more information on
the TV Shape options.
The HDMI Output Setting menu
appears.
Select a HDMI Output Setting
option, and then press [Enter].
See page 46 for more information on
the HDMI output options.
The On-Screen Language menu
appears.
Select a language, and then
press [Enter].
See page 48 for more information on
the language options.
The Initial Setup menu closes.
24
DPC-7.9_En.book Page 25 Tuesday, July 22, 2008 4:37 PM
Powering Up &amp; Setting Up the DPC-7.9—Continued
Your DPC-7.9 is now ready for use. See page 26 for
information on loading discs, and page 27 for information on selecting and playing discs.
Notes:
• You can cancel the Initial Setup by pressing the Open/
Close [ ] button, and complete the settings later by
using the on-screen setup menus (see page 50).
• You can change the language of the on-screen setup
menus, and your preferred languages for DVD menus,
foreign language soundtracks, and subtitles individually on the Language page of the on-screen setup
menus (see page 48).
• Depending on the connected CEC-compatible TV,
some of the DPC-7.9’s settings may change when
RIHD is on.
• Not all DVD-Video discs have multi-language menus,
foreign language soundtracks, and subtitles. In such
cases, the disc’s default language is used.
Resolution
Setting the HDMI
This section explains how to turn HDMI on and off and
change the video resolution when your TV or projector
is connected to the HDMI OUT.
1
2
Remote controller
While “HDMI ON” is displayed,
press the [Resolution] button on
the remote controller repeatedly
to change the HDMI resolution.
The fist button press displays the current resolution on-screen. Press the button again while the resolution is
displayed to change the setting. The
DPC-7.9 supports the following resolutions:
Auto:
The resolution is automatically set
to the native resolution of the TV
connected to the HDMI OUT.
480p(480p/576p):
The setting displayed depends on
the country in which you purchased
the DPC-7.9.
720 &times; 480p 60Hz or 720 &times; 576p
50Hz
480i(480i/576i):
The setting displayed depends on
the country in which you purchased
the DPC-7.9.
720 &times; 480i 60Hz or 720 &times; 576i
50Hz
720p:
1280 &times; 720p 50/60Hz
1080i:
1920 &times; 1080i 50/60Hz
1080p:
1920 &times; 1080p 50/60Hz
Tip:
These settings can also be changed by using the onscreen setup menus (see page 46).
Note:
• Depending on your setup, you may find that there’s no
picture when you turn on HDMI. In this case, you
need to check the HDMI resolution setting and your
TV’s settings. If there is no picture, press the [Resolution] button repeatedly until the picture reappears.
Press the [Resolution] button to
turn HDMI on or off.
If HDMI is off, “HDMI OFF” appears
on the display the first time the button is
pressed. Press the button again while
“HDMI OFF” is displayed to turn on
HDMI.
To turn off HDMI, press and hold the
[Resolution] button.
25
DPC-7.9_En.book Page 26 Tuesday, July 22, 2008 4:37 PM
Basic Playback
Open/Close
Disc Select
3
Remote controller
Disc Skip
Play
4
Open/
Close
Disc Skip
Press the [Disc Skip] button to
access the other disc bays.
The disc tray turns counterclockwise
two bays at a time.
Press the remote controller’s Disc Skip
[+] button to turn the disc tray counterclockwise. Press the Disc Skip [–] button to turn it clockwise.
When you’ve finished, press the
Open/Close [ ] button again.
The disc tray closes.
See page 27 for information on selecting and playing discs.
Remote controller
Tip: If you press the Play [ ] button,
the disc tray will close and playback of
the disc in the right bay will start automatically. If there is no disc in that bay,
the DPC-7.9 will check the other bays
and play the first disc it finds.
Tip: If you press one of the DISC
SELECT 1–6 buttons, the disc tray will
close and playback of the selected disc
will start automatically.
Play
Loading &amp; Removing Discs
DVD
CD
MP3
WMA
JPEG
This section explains how to load and remove discs.
1
Remote controller
2
26
Press the Open/Close [ ]
button.
The disc tray opens and the six disc
number indicators appear on the display. A circle appears around the number of the disc bay on the right.
Place a disc, label side up, into
each bay.
Notes:
• You can load up to six discs. You don’t have to load all
six discs every time.
• When the disc tray is closed, all of the disc indicators
appear until the DPC-7.9 has checked each bay for the
presence of a disc. If a bay is found to have no disc, the
corresponding indicator disappears.
• The disc tray can be opened and closed even while the
DPC-7.9 is in Standby mode, so you don’t have to turn
it on to load or remove your discs. (The disc tray may
take several seconds to open.)
• The DPC-7.9 supports 8 cm and 12 cm discs. To avoid
damaging your discs or DPC-7.9, always place discs
in the center of the disc bays.
• Only load discs that are supported by the DPC-7.9 (see
page 8). Don’t load cartridge-type discs.
• To avoid personal injury, keep your hands away from
the disc tray as it closes.
• Always use the Open/Close [ ] button to open and
close the disc tray. Never push the disc tray, and don’t
touch it, or obstruct it while it’s opening or closing.
Don’t press down on the disc tray while it’s open, and
don’t load anything other than supported discs. Doing
so may damage your discs or DPC-7.9.
DPC-7.9_En.book Page 27 Tuesday, July 22, 2008 4:37 PM
Basic Playback—Continued
Open/Close
Disc Select
Selecting Discs
DVD
CD
MP3
WMA
JPEG
The section explains how to select loaded discs.
Disc Skip
Open/
Close
Disc Skip
Loading Discs During Playback
DVD
CD
MP3
WMA
JPEG
This section explains how to load and remove discs without stopping playback.
1
Remote controller
2
Use the Disc Select buttons to
select loaded discs.
On the display, the number of the current disc has a circle around it.
What happens next depends on the type
of disc you selected, as follows:
DVD-Video:
Typically a menu appears onscreen. See page 29.
Audio CD:
Playback starts automatically.
MP3/WMA/JPEG:
Playback starts automatically.
Note:
• Disc contains different types of
file does not start playback
autoamtically.
Press the Open/Close [ ]
button.
The disc tray opens.
The disc that’s currently playing
remains inside the DPC-7.9 and its disc
bay is empty and won’t come to the
front. To remove this disc you must
stop playback before pressing the
Open/Close [ ] button.
Notes:
• The type of disc currently selected is shown on the display: DVD, or CD (see page 13).
• You can select discs while the DPC-7.9 is stopped or
during playback.
• You can use the [Disc Skip] button to skip the current
disc and start the next disc. If disc #6 is the current
disc, disc #1 will be selected next.
Load or remove discs as
required, and press the [Disc
Skip] button to access the other
disc bays.
Remote controller
3
Remote controller
When you’ve finished, press the
Open/Close [ ] button again.
The disc tray closes.
Playback of the current disc continues
uninterrupted until you either stop
playback or select another disc.
Tip: If you press one of the DISC
SELECT 1–6 buttons, the disc tray will
close, playback of the current disc will
stop, and playback of the newly
selected disc will start automatically.
27
DPC-7.9_En.book Page 28 Tuesday, July 22, 2008 4:37 PM
Basic Playback—Continued
■ Pause
Stop
Remote controller
■ Stop
Pause
Play
To pause playback, press the
Pause [ ] button.
Playback pauses and the Pause indicator appears on the display.
To resume playback, press the Play [ ]
button.
Playback resumes and the Pause
indicator disappears.
To stop playback, press the Stop
[ ] button.
Playback stops and the Play indicator disappears.
Remote controller
Pause
Down
Up
Play
Stop
Enter
Starting, Pausing &amp; Stopping
Playback
DVD
This section explains how to start, pause, and stop playback.
■ Start
Remote controller
28
To start playback, press the Play
[ ] button.
Playback starts and the Play indicator appears on the display.
If the disc is a DVD-Video, you may
need to start playback from a menu (see
page 29).
Notes:
• During playback, you can select chapters or tracks by
using the Up [
] and Down [
] buttons.
• When you stop playback of a DVD-Video disc, the
DPC-7.9 remembers the point at which playback was
stopped. To resume playback from that point, press the
Play [ ] button. To cancel the Resume function, press
the Stop [ ] button again. The Resume function is
reset when another disc is selected.
• With the Last Memory function you can resume playback from a specific point even if the disc has been
removed (see page 40).
• Do not move the DPC-7.9 or subject it to vibration
during playback. Doing so may damage your discs or
DPC-7.9.
• Prolonged display of the same picture or menu may
cause irreparable damage to your TV screen, known as
screen burn-in. To prevent this, don’t keep playback
paused for too long and always press the Stop [ ] button when you’ve finished playing a DVD-Video disc.
Your DPC-7.9 features a screen saver to protect your
TV from the effects of burn-in (see page 48).
With some DVD-Video discs, you may experience picture noise that is not normally visible with regular TV
broadcasts. This is usually because DVD-Video discs
uses a lot of high-resolution video data. The amount of
noise, if any, will depend on your particular TV and the
problem can sometimes be alleviated by turning down
your TV’s sharpness control.
DPC-7.9_En.book Page 29 Tuesday, July 22, 2008 4:37 PM
Basic Playback—Continued
Audio
Subtitle
Notes:
• Not all DVD-Video discs have menus.
• Menu operation varies from disc-to-disc. See the
disc’s sleeve notes for details.
• On some DVD-Video discs, options such as foreign
language soundtracks, subtitles, and audio formats
appear on a separate menu called the disc menu, and
titles and chapters appear on what’s called the title
menu. To display the disc menu, press the [Menu] button. If no menu appears, press the [Top Menu] button.
• With DVD-Video discs, foreign language soundtracks
and audio formats can usually be selected during playback by using the remote controller’s [Audio] button
(see page 41). Similarly, subtitles can be selected by
using the remote controller’s [Subtitle] button (see
page 41).
Enter
Stop
Top Menu
Menu
Play
Navigating Disc Menus
DVD
DVD-Video discs usually have an on-screen menu from
which you can select titles, chapters, and other options,
including foreign language soundtracks, subtitles, and
audio formats (e.g., Dolby Digital or DTS).
1
2
Remote controller
Load and select a DVD-Video
disc.
See page 26 and page 27.
With DVD-Video discs, a menu usually
appears automatically. If it doesn’t, try
pressing the [Top Menu] button.
Use the remote controller’s navigation [ ], [ ], [ ], [ ] buttons to
select items on the menu, and
use the [Enter] button to confirm
your selection.
If you select a playback option (e.g.,
subtitles), another menu of options will
typically appear, in which case you use
the remote controller’s navigation buttons to select items and the [Enter] button to confirm your choice.
Play
Down
Up
Stop
Enter
Top Menu
Menu
Return
29
DPC-7.9_En.book Page 30 Tuesday, July 22, 2008 4:37 PM
Basic Playback—Continued
Using the Disc Navigation Window
CD
MP3
WMA
Press the Down [
] button to restart
the current track. Press it again to select
earlier tracks.
Alternatively, the number button is
used to select a track.
JPEG
On the disc navigation window, you can select CD tracks
or MP3, WMA, or JPEG files.
1
For MP3, WMA, and JPEG discs:
To open a folder, use the remote controller’s Up/Down [ ]/[ ] buttons to
select it, and then press [Enter].
Use the Up/Down [ ]/[ ] buttons to
select tracks in the open folder.
Load and select an audio CD or
MP3, WMA, or JPEG disc.
See page 26 and page 27.
The disc navigation window appears.
It may take a while to read the contents
of discs that contain many files and
folders.
For JPEG discs, press the [Menu] button to open the disc navigation window.
You can select the next or previous
track during playback by using the Up
[
] and Down [
] buttons.
Press the Down [
] button to restart
the current track. Press it again to select
earlier tracks.
This is the display for an MP3 disc.
1
2
Play
1/10
Disc
1/8
Use the Left/Right [ ]/[ ] buttons to
select other folders.
4: DATA
00:00:24
00:05:06
00:05:30
/MP3 music
001. ROOT
002. MP3 music
Repeat
Ramdom
: Off
: Off
To close a folder (i.e., move back up the
directory tree), press the [Return] button.
When all the tracks in that folder have
been played, tracks in the next folder
are played.
If the disc contains MP3/WMA files
and JPEG files, they are played/displayed in order. JPEG files will be displayed in a slideshow. Press the
[Top Menu] button to display the first
nine pictures at thumbnail-size (see
page 35). Depending on the disc, the
first nine pictures may be displayed
automatically.
3
003. Integra 1
004. Integra 2
M
M
M
M
P3
001. Track01
P3
002. Track02
P3
003. Track03
P3
004. Track04
Name: Integra Title
4
Artist Name: Integra Artist
5
A Folder number and file number.
B Elapsed time, remaining time, and
total time of currently playing
song. (Only elapsed time is shown
for WMA files.) (See also page 43.)
C Repeat function and Random
function status.
D For JPEG files, a preview and the
file size are displayed here.
E Information about the song
currently playing (e.g., song title,
artist name, album name) is
displayed here, if available.
2
Remote controller
Press the Play [ ] button to start playback. Press the Stop [ ] button to stop
playback. Press the Pause [ ] button to
pause playback and the Play [ ] button
to resume it.
For audio CDs:
Use the Up/Down [ ]/[ ] buttons to
select a track, and press the Play [ ]
button (or [Enter]) to start playback.
You can select the next or previous
track during playback by using the Up
[
] and Down [
] buttons.
30
3
Press the Stop [ ] button to stop
playback.
Remote controller
Notes:
• You can use the Random Playback function to play a
random selection of MP3/WMA files (page 38).
• During random playback, memory playback, or party
mode playback, the remote controller’s navigation
[ ], [ ], [ ], [ ] buttons, Open/Close [ ] button,
and Disc Skip [+]/[–] buttons cannot be used with the
disc navigation window.
• Depending on their size and format, some JPEG files
cannot be displayed.
DPC-7.9_En.book Page 31 Tuesday, July 22, 2008 4:37 PM
Basic Playback—Continued
3
Play
Remote controller
Use the number buttons to specify a chapter or title.
To enter, for example, “2,” press the [2]
button.
Search
Disc
1:DVD-VIDEO
Title
Current/Total
Chapter
2/
3 Current/Total
2 / 22
To enter, for example, “12,” press the
[1] button, followed by the [2] button.
Search
Search
Disc
Number
buttons
1:DVD-VIDEO
Current/Total
Chapter
2/
3 Current/Total 12 / 22
To clear the number, press the [CLR]
button.
Use the Left/Right [ ]/[ ] buttons to
toggle between Title and Chapter or
Folder and Track.
CLR
4
Play
Up
Down
Title
Enter
Remote controller
Press the Play [ ] or [Enter] button to start playback of the specified chapter or title.
During playback, you can select other
chapters by using the Up [
] and
Down [
] buttons.
Selecting Titles, Chapters &amp; Tracks by
Number
DVD
CD
MP3
WMA
This section explains how to select titles, chapters, and
tracks by number.
1
Load and select a disc.
See page 26 and page 27.
2
Press the [Search] button.
The Search window appears on-screen,
as shown.
This is the display for a DVD-Video
disc.
Remote controller
Notes:
• You can also select chapters by using the number buttons, without opening the Search window.
• If the current DVD-Video disc contains only one title,
you won’t be able to select other titles. Similarly, if it
contains no chapters, you won’t be able to select chapters.
• DVD-Video discs usually have on-screen menus for
selecting titles and chapters (see page 29).
• With some discs you may not be able to select titles
and chapters as described here.
Search
Disc
1:DVD-VIDEO
Title
Current/Total
Chapter
2/
3 Current/Total
4 / 22
With some DVD-Video discs, you can
select only titles, and the Chapter Current/Total information is not displayed.
Some discs won’t allow you to select
titles.
For audio CDs, you can select tracks.
For MP3 and WMA discs, you can
select tracks and folders.
31
DPC-7.9_En.book Page 32 Tuesday, July 22, 2008 4:37 PM
Basic Playback—Continued
Play
2
Remote controller
Use the number buttons to enter
a time.
To enter, for example, 1 hour, 25 minutes, 30 seconds, press the [1], [2], [5],
[3], and [0] buttons.
Search
Disc
1: DVD-VIDEO
Title
1 : 25 : 30
To enter, for example, 2 minutes, 15
seconds, press the [2], [1], and [5] buttons.
Search
Disc
1: DVD-VIDEO
Search
Number
buttons
3
Title
0 : 02 : 15
Press the Play [ ] button to
locate the specified point.
Playback starts from the specified
point.
Remote controller
Play
Locating Specific Points in Time
DVD
CD
With the Time Search function you can locate specific
points in time.
1
Remote controller
Press the [Search] button twice.
The Search window appears on-screen,
as shown.
Search
Disc
1: DVD-VIDEO
32
Title
-- : -- : --
Notes:
• The Time Search function works only within the currently playing title (DVD-Video) or track (audio CD).
For example, if the current title is one hour long and
you enter the time 1 hour, 30 minutes, nothing will
happen.
• In some cases, playback may start from a slightly different point to the one you specified.
• Time Search may not work with some discs.
• You can’t use the [Search] button during random playback, memory playback, or party mode playback.
DPC-7.9_En.book Page 33 Tuesday, July 22, 2008 4:37 PM
Basic Playback—Continued
Play
■ Fast
reverse
Remote controller
Remote controller
Pause
During playback, press the FR
[ ] button to start fast reverse.
Playback reverses and “x 2” appears
on-screen.
To change the fast-reverse speed, press
the FR [ ] button repeatedly to
select: x 2, x 4, x 8, or x 16.
To resume normal playback,
press the Play [ ] button.
Note:
• No sound is output during fast forward or fast reverse
of a DVD-Video, MP3, or WMA disc.
Pause
Play
Down
Up
FR
FF
Frame-by-Frame Playback
DVD
With the Frame-by-Frame Playback function, you can
forward playback one frame at a time.
1
Remote controller
2
Press the Pause [ ] button to
pause playback, and then press
the Pause [ ] button repeatedly
to forward playback one frame at
a time.
To resume normal playback,
press the Play [ ] button.
Remote controller
Fast Forward &amp; Reverse
DVD
CD
MP3
WMA
The section explains how to fast forward and reverse.
■ Fast
forward
Remote controller
Remote controller
During playback, press the FF
[ ] button to start fast forward.
Playback fast forwards and “x 2”
appears on-screen.
To change the fast-forward speed, press
the FF [ ] button repeatedly to select:
x 2, x 4, x 8, or x 16.
Notes:
• No sound is output during frame-by-frame playback.
• Prolonged display of the same picture or menu may
cause irreparable damage to your TV screen, known as
screen burn-in. To prevent this, don’t display the same
frame for too long. Your DPC-7.9 features a screen
saver to protect your TV from the effects of burn-in
(page 48).
To resume normal playback,
press the Play [ ] button.
33
DPC-7.9_En.book Page 34 Tuesday, July 22, 2008 4:37 PM
Basic Playback—Continued
Slow-motion Playback
DVD
With the Slow-motion Playback function you can watch
a scene slowly either forward or backward.
■ Forward
slow
motion
Remote controller
During playback, press the Slow
[ ] button.
Forward slow-motion playback starts
and “ 1/2” appears on-screen.
To change the slow-motion speed, press
the Slow Forward [ ] button repeatedly to select: 1/2, 1/4, 1/6, or 1/8.
Dimmer
Adjusting the Display Brightness
You can adjust the brightness of the display as follows.
■ Backward During playback, press the Slow
slow
[ ] button.
motion
Backward slow-motion playback starts
and “ 1/2” appears on-screen.
Remote controller
To change the slow-motion speed, press
the Slow Back [ ] button repeatedly
to select: 1/2, 1/4, 1/6, or 1/8.
■ Resume
playback
To resume normal playback,
press the Play [ ] button.
Remote controller
Notes:
• No sound is output during slow-motion playback.
• The slow-motion speed indication is only approximate, and the actual speed will vary from disc to disc.
34
1
Press the [Dimmer] button
repeatedly to cycle through the
following options:
Disc tray light off + normal brightness
Disc tray light off + dim
Disc tray light off + dimmer
Disc tray light on + normal brightness
Notes:
• When the display brightness on another Integra/
Onkyo AV component connected via
is changed,
the “disc tray light off” option might not work.
• Even if you selected the “disc tray light off” option,
the disc tray light will come on when the disc tray is
opened.
• The display brightness cannot be adjusted via RIHD.
DPC-7.9_En.book Page 35 Tuesday, July 22, 2008 4:37 PM
Basic Playback—Continued
Stop
2
You can use the following functions during the slideshow:
To display the next or previous picture,
use the Up [
] and Down [
] buttons.
To turn a picture upside down, use the
Up/Down [ ]/[ ] buttons (not while
zoomed in).
To rotate a picture clockwise or counterclockwise, use the Left/Right [ ]/
[ ] buttons (not while zoomed in).
To pause the slideshow, press the [ ]
button. Press the Play [ ] button to
resume.
To zoom in or out, use the FF [ ] and
FR [ ] buttons. Use the Left/Right
[ ]/[ ] and Up/Down [ ]/[ ] buttons
to move around the picture while
zoomed in. To cancel the zoom, press
the Play [ ] button.
To return to the navigation window,
press the [Menu] button.
To view the thumbnail display, press
the [Top Menu] button.
Use the Up [
] and Down [
] buttons to display the next or previous
thumbnail page.
3
To stop the slideshow, press the
Stop [ ] or [Menu] button.
Depending on the type of JPEG disc,
either the first nine pictures appear in
thumbnail-size or the disc navigation
window appears.
The slideshow stops automatically
when all pictures have been displayed.
Pause
Play
Pause
Play
Down
Up
FR
Stop
FF
Enter
Remote controller
Top Menu
Menu
Using JPEG CDs
The DPC-7.9 supports JPEG CDs, so you can view your
photos on TV either individually or as a slideshow.
1
Load and select a CD containing
JPEG pictures.
Use the [ ], [ ], [ ], [ ] buttons to
select a picture, and then press the Play
[ ] or [Enter] button to start the slideshow.
Notes:
• You can view JPEG images in high definition by
changing the HD JPEG mode setting (see page 46).
• The Memory and Random functions cannot be used
with JPEG files.
• Chain mode cannot be used with JPEG files.
• The Zoom function cannot be used in HD JPEG mode.
35
DPC-7.9_En.book Page 36 Tuesday, July 22, 2008 4:37 PM
Basic Playback—Continued
Chain Mode
Party Mode
Using Chain Mode
DVD
CD
MP3
WMA
With the Chain mode function, you can play all discs, all
DVD-Video discs, or all audio CDs and MP3/WMA
discs consecutively as if they were one big disc.
1
Remote controller
2
Remote controller
Press the [Chain Mode] button
repeatedly to select CD, DVD, or
ALL.
The CHAIN MODE indicator flashes
on the display.
ALL:
All discs are played consecutively.
DVD:
All DVD-Video discs are played
consecutively.
CD:
All audio CDs, including MP3 and
WMA discs, are played consecutively.
To cancel Chain mode, press the [Chain
Mode] button repeatedly until the
CHAIN MODE indicator disappears.
While the CHAIN MODE indicator
is flashing, press the Play [ ]
button to start Chain mode playback.
The Chain mode function will be cancelled if you do not start playback
within 5 seconds of pressing the [Chain
Mode] button.
Note:
• JPEG files are skipped during Chain mode playback.
• With the DVD and All Chain modes, DVD-Video
menus are ignored and titles are played automatically.
This may not work with some discs.
• You can’t use the repeat functions with Chain mode.
• You can use the Random function with Chain mode.
36
Using Party Mode
CD
MP3
WMA
With the Party mode function, you can play all of the
audio CDs and MP3/WMA discs in random order.
Remote controller
Press the [Party Mode] button.
The CHAIN MODE and CD indicators
appear.
All loaded audio discs, including MP3
and WMA discs, are played in random
order.
Press the Stop [ ] button to stop Party
mode playback and cancel the Party
mode function.
DPC-7.9_En.book Page 37 Tuesday, July 22, 2008 4:37 PM
Advanced Playback
Repeat Playback
DVD
CD
MP3
WMA
JPEG
With the Repeat Playback function you can play the current disc, title, chapter, track, or folder of MP3/WMA
files over-and-over again.
1
Repeat
Remote controller
2
Play
Remote controller
3
Search
Remote controller
Press the Play [ ] button to start
repeat playback.
Press the [Repeat] button repeatedly to select a repeat option.
The currently selected repeat option
appears on-screen and “REPEAT”
appears on the display.
The available options depend on the
current disc type, as follows:
DVD-Video:
Chapter, Title, 1 Disc, All Discs.
Audio CD:
Track, 1 Disc, All Discs.
MP3/WMA/JPEG:
Track, Folder, 1 Disc, All Discs.
To cancel Repeat Playback, use
the [Repeat] button to select Off.
Repeat
A-B
Random
Up
Play
Notes:
• Repeat Playback may not work with some
DVD-Video discs.
• If you press the [Repeat] button while the Memory
Playback function is on (see page 39), the current
memory list will play repeatedly.
• The Repeat function cannot be used with Chain mode
or Party mode.
• If you select another disc, repeat playback is cancelled.
• The Repeat function can be used in combination with
the Random function (see page 38).
37
DPC-7.9_En.book Page 38 Tuesday, July 22, 2008 4:37 PM
Advanced Playback—Continued
A–B Repeat Playback
DVD
CD
MP3
Audio CD:
1 Disc, All Discs.
MP3/WMA:
Folder (files in subfolders are not
played), 1 Disc, All Discs.
With the “Title” option, chapters within
the current title are played at random.
With the “1 Disc” option, all titles,
chapters, tracks, and folders on the current disc are played at random.
If you press the [Random] button during playback, random playback begins
after the current chapter, or track has
finished.
WMA
With the A–B Repeat Playback function you can play a
specified section over-and-over again.
1
Remote controller
2
Remote controller
3
Remote controller
During playback, press the [A–B]
button to set the A point (i.e., the
start of the section you want to
repeat).
“Repeat A–” appears on-screen.
Press the [A–B] button again to
set the B point (i.e., the end of the
section you want to repeat).
Playback repeats between the A and B
points, and “Repeat A–B” appears onscreen.
To cancel A–B Repeat Playback,
press the [A–B] button to select
Off.
3
Remote controller
4
Remote controller
Notes:
• A–B Repeat Playback may not work with some
DVD-Video discs.
• In some cases, the A and B points may be at slightly
different points to the ones you specified.
Random Playback
DVD
CD
MP3
WMA
With the Random Playback function you can enjoy a
random selection of discs, titles, chapters, tracks, or
MP3/WMA folders.
1
Select a disc.
See page 27.
2
Press the [Random] button
repeatedly to select a random
option.
The currently selected random option
appears on-screen.
The available options depend on the
current disc type, as follows:
DVD-Video:
Title, 1 Disc, All Discs.
Remote controller
38
Press the Play [ ] button to start
random playback.
Random playback starts.
To cancel random playback, use
the [Random] button to select
Off.
Notes:
• To select the next random disc, title, chapter, track, or
MP3/WMA folder during random playback, press the
Up [
] button.
• Random playback may not work with some
DVD-Video discs.
• Random playback cannot be used with the Memory
Playback function.
• You can’t use the [Search] button during random playback.
• During random playback, the remote controller’s navigation [ ], [ ], [ ], [ ] buttons and number buttons
cannot be used with the disc navigation window.
• If you select another disc, random playback is cancelled, except when the random option is set to “All
Disc,” in which case playback continues.
• The Random Playback function can be combined with
the Repeat Playback function.
DPC-7.9_En.book Page 39 Tuesday, July 22, 2008 4:37 PM
Advanced Playback—Continued
3
Remote controller
Press the [Enter] button.
The new item is added to the memory
list as step 01.
Memory List
No.
Number
buttons
Memory
Disc
Title/Folder
Chapter/Track
1
Chapter/Total 001 / 002
Current/Total --- / 008
01
02
1
-
001 / 002
--- / ---
005 / 008
--- / ---
03
-
--- / ---
--- / ---
04
-
--- / ---
--- / ---
05
-
--- / ---
--- / ---
CLR
4
Repeat steps 2 and 3 to add more
items to the memory list.
New items will be added to the memory
list as steps 02, 03, and so on.
5
To play the memory list, press
the Play [ ] button.
Last
Memory
Play
Remote controller
Stop
Enter
6
Remote controller
To stop playback, press the Stop
[ ] button.
Memory Playback
DVD
CD
MP3
WMA
With the Memory Playback function, you can create
your own memory list of up to 32 titles, chapters, or
tracks.
1
Remote controller
Press the [Memory] button.
The Memory List window appears onscreen, as shown.
Inserting New Items in the List
Remote controller
Memory List
No.
Disc
1
01
02
03
04
05
-
Title/Folder
Chapter/Total 001 / 002
--- / ----- / ----- / ----- / ----- / ---
Chapter/Track
Current/Total --- / 008
--- / ----- / ----- / ----- / ----- / ---
To insert a new item into the
memory list, use the Up/Down
[ ]/[ ] buttons to select the step
before which you want to insert
the new item, and then press the
[Enter] button.
Memory List
The top row ( ) is used to enter disc,
title/folder, and chapter/track numbers.
Steps in the memory list are numbered.
2
Remote controller
Enter the disc, title/folder, and
chapter/track numbers of the
item you want to add to the memory list.
Use the remote controller’s Left/Right
[ ]/[ ] buttons to select the parameters, and use the number buttons to
select Title/Folder or Chapter/Track.
The number of the currently selected
disc is already entered.
To add all of the titles, folders, chapters,
or tracks on the disc, press the [+10]
button.
No.
01
02
03
04
05
Remote controller
Disc
Title/Folder
Chapter/Track
1
Chapter/Total 001 / 002
Current/Total --- / 008
1
1
3
-
001 / 002
--- / --001 / 002
001 / ----- / ---
005 / 008
--- / --003 / 008
--- / 008
--- / ---
Enter the disc, title/folder, and
chapter/track numbers of the
item to be inserted.
Press the [Enter] button.
The new item is inserted into the memory list and subsequent items move
down the list.
39
DPC-7.9_En.book Page 40 Tuesday, July 22, 2008 4:37 PM
Advanced Playback—Continued
Deleting Items from the List
Remote controller
To delete an item, use the Up/
Down [ ]/[ ] buttons to select it,
and then press the [CLR] button.
The item is deleted and subsequent
items move up the list.
1
Remote controller
2
Editing Steps
1
Remote controller
To edit a step, use the Up/Down
[ ]/[ ] buttons to select it, edit
the disc, title/folder, and chapter/
track numbers, and then press
the [Enter] button.
Remote controller
3
Remote controller
2
Remote controller
Remote controller
DVD
With the Last Memory function you can resume playback from where you left off even if another disc has
been selected or the disc has been removed. Last Memory also remembers the soundtrack and subtitle languages that you were using.
40
To resume playback, select the
disc and press the Play [ ] button.
The Last Memory dialog box appears,
as shown.
Yes
4
Using Last Memory
To stop playback, press the Stop
[ ] button once or twice.
At this point you may choose to
play another disc, or to turn off
the DPC-7.9.
Last Memory is set.
Start playback from memory location ?
To close the Memory Play Setup
window, press the [Return] button.
• Deleting the memory list:
Press the Stop button to stop playback of the memory
list, and while “Memory” is displayed on-screen,
press the [CLR] button. The memory list is deleted and
“Memory Clear” is displayed on-screen.
Note:
• The entire memory list is cleared when the DPC-7.9 is
set to Standby.
During playback, press the
[Last Memory] button.
The last memory point for the disc is
stored, the LAST indicator appears,
and “LAST MEM” appears on the display.
If the [Last Memory] button is pressed
again, the last memory point will be
updated.
No
Memory Clear
To resume playback from last
memory point, select “Yes,” and
then press [Enter].
To start playback from the beginning,
select “No,” and then press [Enter].
To start playback from the beginning
and delete the last memory point, select
“Memory Clear,” and then press
[Enter].
Notes:
• The Last Memory function can store the settings for
up to six DVD-Video discs. When you set the Last
Memory function for a seventh disc, the first disc’s settings are lost.
• The Last Memory function will not work while a
menu is being displayed on-screen.
• The Last Memory function may not work with some
DVD-Video discs.
• Even if you select another disc, or inadvertently turn
off the DPC-7.9 during playback, you can resume
playback from the same point when you select the disc
again.
DPC-7.9_En.book Page 41 Tuesday, July 22, 2008 4:37 PM
Advanced Playback—Continued
Selecting Languages &amp; Audio
Formats
DVD
Some DVD-Video discs feature soundtracks in several
languages and audio formats (e.g., Dolby Digital or
DTS). Music DVD-Video discs sometimes feature
soundtracks in several audio formats, such as PCM or
Dolby Digital 5.1. See the disc’s sleeve notes for details.
Angle
Audio
Remote controller
Subtitle
Selecting Camera Angles
DVD
Some DVD-Video discs feature multiple camera angles
that allows you to view scenes from different angles. If
the currently playing DVD-Video disc features multiple
camera angles, the camera
indicator appears on the
display. Such a disc usually has the multiple camera
angle logo ( ) printed on its sleeve notes.
Remote controller
Press the [Angle] button repeatedly to cycle through the available camera angles.
The number of the currently selected
camera angle appears on-screen. For
example, on a disc with three camera
angles, you’d see 1/3, 2/3, and 3/3.
Notes:
• With some DVD-Video discs you may not be able to
select different camera angles even though the camera
indicator is displayed.
• With some DVD-Video discs you can select camera
angles from a menu.
• Some DVD-Video discs won’t allow you to select different camera angles while playback is paused.
During playback, press the
[Audio] button repeatedly to
cycle through the available
soundtracks.
The name of the selected soundtrack
appears on-screen for several seconds.
Notes:
• With DVD-Video discs, when you stop playback and
cancel the Resume function (see page 28), or select
another disc, the soundtrack language will revert to
your default language (see page 48), or the disc’s
default language.
• With some discs, selecting another soundtrack may
cause the picture to skip momentarily.
• With some DVD-Video discs you need to select
soundtracks from a menu, and you may not be able to
select other soundtracks during playback.
Selecting Subtitles
DVD
Some DVD-Video discs feature subtitles in several languages. See the disc’s sleeve notes for details.
Remote controller
During playback, press the [Subtitle] button repeatedly to cycle
through the available subtitles.
The name of the selected subtitle
appears on-screen for several seconds.
To turn off subtitles, use the [Subtitle]
button to select Off.
Notes:
• With DVD-Video discs, when you stop playback and
cancel the Resume function (see page 28), or select
another disc, the subtitle language will revert to your
default subtile language (see page 48), or the disc’s
default subtitle language.
• With some DVD-Video discs you can select subtitles
from a menu, and you may not be able to select subtitles during playback.
• To check the subtitle language currently selected,
press the [Subtitle] button once. The current setting
will appear on-screen for several seconds.
41
DPC-7.9_En.book Page 42 Tuesday, July 22, 2008 4:37 PM
Advanced Playback—Continued
Play
Stop
Enter
Zoom
Zooming
DVD-V
JPEG
With the Zoom function you can enlarge any part of the
picture.
1
Remote controller
2
Remote controller
3
Remote controller
During playback or paused,
press and hold the [Zoom] button.
“Zoom x 1.0” appears on-screen.
Press the [Zoom] again repeatedly to Zoom in.
The number of zoom steps available
depends on the resolution of the disc or
file.
After the maximum zoom, the picture
returns to its normal size.
To see other areas of the picture
while zoomed, use the remote
controller’s arrow [ ], [ ], [ ],
[ ] buttons.
Notes:
• During a JPEG slideshow, you can use the FF [ ]
and FR [ ] buttons to zoom in and out.
• The Zoom function may not work with some DVDs.
• The Zoom function can also be used while playback is
paused or during slow-motion playback.
• The Zoom function cannot be used with HD JPEG.
42
DPC-7.9_En.book Page 43 Tuesday, July 22, 2008 4:37 PM
Advanced Playback—Continued
Displaying Information
DVD
You can display various information about the current
disc, title, chapter, or track as follows.
1
Display
Remote controller
Display
2
Remote controller
3
During playback, press the [Display] button.
Various information appears on-screen.
The operating status (e.g., Stop, Play,
Resume), disc number, and disc type
information is displayed along the top
of the screen.
DVD-Video:
Current title number, total number
of titles on disc, elapsed title time,
remaining title time, total title time,
selected soundtrack, selected subtitle, and the number of available
camera angles.
Press the [Display] button again
to see more information.
DVD-Video: Current chapter number,
total number of chapters in title,
elapsed chapter time, remaining chapter time, total chapter time.
Press the [Display] button again
to cancel the information display.
Remote controller
■ For audio CDs:
Pressing the [Display] button repeatedly during playback will display the following information:
• Elapsed track time (on-screen, the elapsed track time
and remaining track time will be displayed)
• Remaining track time
• Elapsed disc time (on-screen, the elapsed disc time
and remaining disc time will be displayed)
• Remaining disc time
■ For MP3 and WMA discs:
Pressing the [Display] button repeatedly during playback will display the following information:
• Elapsed track time
• Track name
• Folder name
• Total number of folders
43
DPC-7.9_En.book Page 44 Tuesday, July 22, 2008 4:37 PM
Configuring the DPC-7.9
This chapter explains the various functions and settings of the on-screen setup menus.
Functions and settings are arranged into six menus: Picture, Audio, Language, Display, Operation Setting, and
Initial Setup.
The following table lists all the functions and settings, with a brief description and page number where you can find full
details.
Menu
Picture
Audio
Language
Display
Operation
Setting
Initial Setup
Setting
Description
TV Shape
Select the aspect ratio that matches your TV.
45
View Mode
Stretch the picture to fit your TV screen.
46
HDMI Output Setting
Turn HDMI video output on or off.
46
Progressive Setting
Set the component video output to progressive or interlaced.
46
HD Resolution
Select the video resolution for the HDMI OUT.
46
HD JPEG mode
For displaying JPEG images at a high resolution on a HDTV.
46
Video Black Level
Choose a video black level.
47
Brightness
Adjust the picture brightness.
47
Sharpness
Adjust the picture sharpness.
47
PAL Output Setting (European and Australian models only)
Convert the disc’s video format.
47
Digital/HDMI Audio Out
Settings for the digital signal output by the optical, coaxial, and
HDMI digital audio outputs.
47
Linear PCM Out
Select whether or not the DPC-7.9 downsamples 96 kHz digital audio.
47
Dynamic Range Control
Set the Dynamic Range function.
47
On-Screen Language
Select a language for the on-screen setup menus and messages.
48
Disc Menu Language
Select your preferred language for disc menus.
48
Audio Language
Select your preferred language for soundtracks.
48
Subtitle Language
Select your preferred language for subtitles.
48
On-Screen Display
Turn on or off on-screen messages and indicators.
48
On-Screen Display Color
Select a color for on-screen setup menus and messages.
48
Background
Select a background color for when playback is stopped.
48
Screen Saver
Set the Screen Saver function.
48
Parental Lock
Set the Parental Lock function.
49
Security Code
Change a security code for use with parental lock.
49
HDMI Control
Turn on or off RIHD control over HDMI.
50
Power Control
Turn on or off RIHD power control over HDMI.
50
Direct Change
Turn on or off RIHD direct change over HDMI.
50
Auto Power Off
Sets the Auto power off function.
50
This menu appears automatically the very first time you turn on
your DPC-7.9. (These settings are available in other menus.)
24
TV Shape
HDMI Output Setting
On-Screen Language
44
Page #
DPC-7.9_En.book Page 45 Tuesday, July 22, 2008 4:37 PM
Configuring the DPC-7.9—Continued
6
Remote controller
When you’ve finished, press the
[Setup] button again.
The on-screen setup menu closes.
Enter
Setup
Picture Menu
TV Shape
Using the On-screen Setup Menus
This section explains how to use the on-screen setup
menus.
1
Turn on your DPC-7.9 and TV.
On your TV, select the video input to
which the DPC-7.9 is connected.
2
Press the [Setup] button.
The on-screen setup menu appears, as
shown.
Remote controller
Picture
3
Remote controller
4
Remote controller
5
Remote controller
TV Shape
: 16:9 Compressed
View Mode
: Normal
HDMI Output Setting
: On
Progressive Setting
: Interlace
HD Resolution
: Auto
HD Jpeg mode
: Off
Video Black Level
: Light
Brightness
:4
Sharpness
:4
Use the remote controller’s navigation buttons to navigate the
menus.
Use the Left/Right [ ]/[ ] buttons to
move left or right. Use the Up/Down
[ ]/[ ] buttons to move up or down.
When you’ve selected an item,
press the [Enter] button to see
the available options.
Use the navigation buttons to
select the options, and press the
[Enter] button to confirm your
selection.
Press the [Return] button to go back
one step.
With this setting you can select a picture format to match
the aspect ratio of your TV.
4:3 Letter box: Choose this
option if you have a standard TV
(4:3 aspect ratio). When you
watch widescreen DVD-Video
movies, the entire picture will be
visible and there will be black
bars at the top and bottom of the screen, as shown.
4:3 Pan &amp; Scan: Choose this
option if you have a standard TV
(4:3 aspect ratio) and want to use
the full height of the screen when
watching widescreen
DVD-Video movies. In order to
use the full height of the screen, the picture will be
cropped on both sides, as shown. This option won’t
work with discs that don’t support pan and scan.
16:9 Widescreen: Choose this option if you have a
widescreen TV (16:9 aspect ratio). Depends on TV,
the picture appears stretched when watching programs
in 4:3 format.
16:9 Compressed (default):
Choose this option if you
have a widescreen TV (16:9
aspect ratio) and the picture
appears stretched when
watching programs in 4:3 format. Some widescreen TVs
have a setting to correct this. If your TV doesn’t, and
4:3 programs appear stretched, select this option to correct the problem.
Notes:
• This setting does not apply to DVD menus.
• When the HDMI OUT signal is at a resolution of
720p, 1080i, or 1080p programs in 4:3 format will
appear stretched, so we recommend that you select the
16:9 Compressed option.
• With some DVD-Video discs this setting may have no
effect. See the disc’s sleeve notes to see which picture
format is used.
45
DPC-7.9_En.book Page 46 Tuesday, July 22, 2008 4:37 PM
Configuring the DPC-7.9—Continued
View Mode
HD Resolution
With this setting you can adjust the aspect of the picture
so that it fits your TV screen. Due to your TV’s aspect
ratio setting and the DVD’s aspect ratio, black bars may
appear above and below the picture or at the sides and the
aspect of the picture may be unsuitable. In this case, use
this setting to adjust the aspect of the picture as you like.
With this setting you can set the video resolution for the
HDMI OUT.
Normal (default): The picture is displayed in its
original aspect ratio.
View Mode 1: The picture is stretched horizontally
to make it fit the height of the screen.
View Mode 2: The picture is stretched vertically to
make it fit the width of the screen.
View Mode 3: The picture is stretched horizontally
and vertically to make it fit the screen.
Tip:
The view mode can also be changed by using
the remote controller’s [Aspect] button.
Note:
• This setting does not apply to DVD menus.
HDMI Output Setting
With this setting you can turn the HDMI video output on
or off. See page 25 for more information.
On (default): Video is output by the HDMI OUT.
Off: Video is not output by the HDMI OUT.
Progressive Setting
With this setting you can set the component video output
to progressive or interlaced. While the HDMI Output Setting is set to On, this setting is fixed at Interlaced and cannot be changed. See page 25 for more information.
Interlaced: Component video output is interlaced.
Progressive: Component video output is progressive.
Notes:
• When Progressive is selected, no video is output by
the composite video, S-Video, and HDMI outputs.
• This setting can also be changed by pressing and holding the Down [
] button, and then pressing [On/
Standby] button.
46
Auto (default): The resolution is automatically
scaled to the preferred resolution of the TV connected to the HDMI OUT.
If Auto is selected but the DPC-7.9 doesn’t support
the resolution preferred by the TV, the resolution will
be 480p/576p.
480i (480i/576i): The setting displayed depends on
the country in which you purchased the DPC-7.9.
720 x 480i 60 Hz or 720 x 576i 50 Hz
480p (480p/576p): The setting displayed depends on
the country in which you purchased the DPC-7.9.
720 x 480p 60 Hz or 720 x 576p 50 Hz
720p: 1280 x 720p 50/60 Hz
1080i: 1920 x 1080i 50/60 Hz
1080p: 1920 x 1080p 50/60 Hz
Tip:
When the HDMI Output Setting is set to On, you can
also change this setting by using the remote controller’s
[Resolution] button (see page 25).
Note:
• If Auto selected but the DPC-7.9 doesn’t support the
TV’s native resolution, the resolution will be 480p/
576p.
HD JPEG mode
If your TV is connected to the HDMI OUT and the
HDMI resolution is set to 720p, 1080i, or 1080p, this setting allows you to display your JPEG pictures in high
definition.
On: JPEG pictures displayed in high definition.
Off (default): JPEG pictures displayed as normal.
Notes:
• If your TV is connected to a video output other than
the HDMI OUT, or the HD Resolution set to something other than 720p, 1080i, or 1080p, even if this
setting is set to On, your JPEG pictures will not be
displayed in high definition.
• When using HD JPEG, it may take a while to display
each picture. And the Zoom function cannot be used.
Also, on-screen status messages such as “Play” and
“Stop” are not displayed.
DPC-7.9_En.book Page 47 Tuesday, July 22, 2008 4:37 PM
Configuring the DPC-7.9—Continued
Video Black Level
With this setting you can adjust the picture blackness of
analog video output.
Light: Blacks are lighter, and the entire picture
becomes lighter.
Dark: Blacks are darker, and the entire picture
becomes darker.
On the North American model, Light is the default setting. On the Australian model, Dark is the default setting.
Brightness
With this setting you can adjust the picture brightness.
1-7: 1 is the darkest. 7 is the brightest. The default
brightness is 4 (default).
Sharpness
With this setting you can adjust the picture sharpness.
1-7: 1 is the softest. 7 is the sharpest. The default
sharpness is 4 (default).
Audio Menu
Digital/HDMI Audio Out
With this setting you can configure the optical, coaxial,
and HDMI digital outputs.
All (default): Dolby Digital and DTS signals are output as they are.
PCM: Dolby Digital signals are down mixed to 2
channels and output as PCM.
Off: No digital signals are output.
Linear PCM Out
With this setting you can configure the DPC-7.9 to output digital audio with higher sampling rates (e.g.,
96 kHz) as it is or down sample it to 48 kHz.
If the AV component you connect to the DPC-7.9’s digital audio outputs supports 96 kHz digital audio, select
Down Sample Off. Otherwise, select Down Sample On.
Down Sample On: 96 kHz digital audio is down
sampled and output at 48 kHz.
PAL Output Setting (European and
Australian models only)
With this setting you can specify how the DPC-7.9 outputs video signals.
AUTO (default): Use this option to watch PAL and
NTSC format discs. The DPC-7.9 does not convert
the video format. When you play a PAL disc, the
video output will be PAL format. And when you play
an NTSC disc, it’ll be NTSC format. Your TV must
support NTSC playback in order to watch NTSC format discs.
NTSC: Use this option if you want to play only
NTSC format discs. When you play a PAL disc, the
DPC-7.9 will convert PAL format video signals to
NTSC-compatible format.
PAL: Use this option if your TV doesn’t support
NTSC playback, or the picture is distorted when
watching NTSC discs. The DPC-7.9 will convert
NTSC format video signals to PAL-compatible format.
Note:
• This setting can also be changed by pressing and holding the Up
button, and then pressing [On/
Standby] button.
Down Sample Off (default): 96 kHz digital audio is
output as it is.
Notes:
• Some copy-protected DVD-Video discs may use
96 kHz digital audio only for A/D conversion to the
analog audio outputs.
• With some discs, even if you select Down Sample Off,
the digital audio will be down sampled to 48 kHz, and
in some cases may not be output by the DPC-7.9’s digital audio outputs.
Dynamic Range Control (Dolby Digital
only)
With the Dynamic Range Control function you can
reduce the dynamic range of Dolby Digital material so
that you can still hear quiet parts even when listening at
low volume levels—ideal for watching movies late at
night when you don’t want to disturb anyone.
On: The dynamic range of Dolby Digital material is
compressed.
Off (default): The full dynamic range is preserved.
Notes:
• The impact of the Dynamic Range Control function
depends on the Dolby Digital material that you are
playing and with some material there will be little or
no effect.
• When the DPC-7.9 is set to Standby, this function is
automatically set to off.
47
DPC-7.9_En.book Page 48 Tuesday, July 22, 2008 4:37 PM
Configuring the DPC-7.9—Continued
Language Menu
• With some DVD-Video discs you can select subtitles
from a menu.
On-Screen Language
On-Screen Display
Disc Menu Language
With this setting you can turn on or off on-screen messages, such as “Play,” “Stop,” and “Resume.”
With this setting you can select your preferred language
for disc menus. When you play a DVD-Video disc with
multiple language disc menus, your preferred language
will be selected automatically.
Select “Others” if you can’t find your language displayed. See “Selecting Other Languages” on page 50.
Notes:
• Not all DVD-Video discs have menus in multiple languages.
• Even if a DVD-Video disc has menus in multiple languages, this setting may not always work.
• If a DVD has only one menu language, that will be
used.
• With some DVD-Video discs you can select languages
from a menu.
Audio Language
With this setting you can select your preferred language
for soundtracks. When you play a DVD-Video disc with
multiple language soundtracks, your preferred language
will be selected automatically.
Select “Others” if you can’t find your language displayed. See “Selecting Other Languages” on page 50.
Notes:
• Not all DVD-Video discs have soundtracks in multiple
languages.
• Even if a DVD-Video disc has soundtracks in multiple
languages, this setting may not always work.
• If a DVD has only one soundtrack, that will be used.
• With some DVD-Video discs you can select languages
from a menu.
Subtitle Language
With this setting you can select your preferred language
for subtitles. When you play a DVD-Video disc with
multiple language subtitles, your preferred language will
be selected automatically.
Select “No Subtitle” if you don’t want subtitles displayed. Select “Others” if you can’t find your language.
See “Selecting Other Languages” on page 50.
Notes:
• Not all DVD-Video discs have subtitles.
• Even if a DVD-Video disc has subtitles in multiple
languages, this setting may not always work.
• If a DVD has only one subtitle language, that will be
used.
48
Display Menu
With this setting you can select a language for the onscreen setup menus and messages.
Select one of the displayed language.
On (default): On-screen messages are displayed.
Off: On-screen messages are not displayed.
On-Screen Display Color
With this setting you can set the color and theme of the
Disc navigation window.
Pearl (default):
Sapphire:
Amethyst:
Garnet:
Background
With this setting you can select the color of the background that’s displayed when the DPC-7.9 is stopped.
Blue:
Gray:
Graphic (default): The theme picture specified for
the On-Screen Display Color setting is used.
Screen Saver
With the Screen Saver function you can protect your TV
against screen burn-in, which can occur when the same
image or menu is displayed for a long time.
On (default): Screen saver on.
Off: Screen saver off.
When the Screen Saver function is set to On, and
DVD-Video playback is stopped for 15 minutes, the
Screen Saver function automatically displays a moving
image.
Once the screen saver has been activated, you can cancel
it by pressing the Play [ ] button.
Note:
• The Screen Saver function also works with audio CDs
and MP3/WMA discs.
DPC-7.9_En.book Page 49 Tuesday, July 22, 2008 4:37 PM
Configuring the DPC-7.9—Continued
Operating Setting Menu
Parental Lock
With the Parental Lock function you can block access to
certain scenes that the authors have flagged as being
unsuitable for children.
To use parental lock, you must set a security code.
1
Select “Operation Setting” menu
in the setup.
2
Use the navigation [ ]/[ ]/[ ]/[ ]
buttons to select “Parental
Lock”, and then press the [Enter]
button.
The security code input screen appears.
Remote controller
3
Remote controller
4
Remote controller
• Not all discs use parental lock. See the disc’s sleeve
notes for details.
• Discs with parental lock may cut certain scenes,
replace certain scenes with children-friendly scenes,
or prevent playback of the entire disc.
Change the Security Code
To change the Security Code, confirm your existing code
then enter a new one.
1
Select “Operation Setting” menu
in the setup.
2
Use the navigation [ ]/[ ]/[ ]/[ ]
buttons to select “Security
Code”, and then press the [Enter]
button.
The security code input screen appears.
Remote controller
Enter the security code using the
remote controller’s number buttons, and then press the [Enter]
button.
The default security code is “8888.”
You can change the security code in the
next step.
Remote controller
Use the Up/Down [ ]/[ ] buttons
to change the level of parental
lock, and then press the [Enter]
button.
At level 8 parental lock is off, with level
1 being the strictest level.
Remote controller
Notes:
• When entering a security code, you can use the [CLR]
button to delete the numbers entered so far, if necessary.
3
4
Enter the existing security code
using the remote controller’s
number buttons, and then press
the [Enter] button.
The default security code is “8888.”
Even if a new security code has been
entered, the code “8888” can still be
used.
Once the security code has been
entered, the new security code input
screen appears.
Enter the new security code
using the remote controller’s
number buttons, and then press
the [Enter] button.
The new security code has been set.
Note:
• If you forget your security code, enter “8888” instead.
“8888” is a security code that can always be used.
49
DPC-7.9_En.book Page 50 Tuesday, July 22, 2008 4:37 PM
Configuring the DPC-7.9—Continued
HDMI Control
With this setting, you can turn RIHD control over HDMI
on or off.
On (default): RIHD control on.
Off: RIHD control off.
Notes:
• RIHD (Remote Interactive over HDMI) is Onkyo’s
implementation of CEC (Consumer Electronics Control), which allows integrated system control over
HDMI and is part of the HDMI standard. In addition
to Integra/Onkyo AV components, it allows interoperability with CEC-compatible AV components and TVs
made by other manufacturers. However, operation
with components other than RIHD-compatible components or recommended components cannot be guaranteed.
• Select Off if a connected component is incompatible
or you’re not sure about its compatibility.
• If operation is unreliable when set to On, select Off
instead.
Power Control
With this setting, you can turn RIHD power control over
HDMI on or off.
On (default): RIHD power control on.
Off: RIHD power control off.
Notes:
• The Power Control setting can be set only when the
HDMI Control setting is set to On.
• When set to On, the DPC-7.9 can be turned on or off
automatically along with the other RIHD-compatible
components in the system.
• HDMI power control only works with RIHD-compatible components that support it and may not work
properly with some components due to their settings
or compatibility.
• When set to On, the DPC-7.9 consumes more power.
• When set to On, the DPC-7.9 enters Standby mode
and the Standby indicator lights up.
erly with some components due to their settings or
compatibility.
Auto Power Off
The Auto power off function automatically turns off the
DPC-7.9 after 20 minutes of inactivity.
Initial Setup Menu
This menu appears automatically the very first time you
turn on the DPC-7.9. See “First Time Setup” on page 24
for more information.
TV Shape—see page 45
HDMI Output Setting—see page 46
On-Screen Language—see page 48
Selecting Other Languages
This section explains how to select other languages for
disc menus, audio, and subtitles.
1
Remote controller
2
Remote controller
3
Remote controller
Direct Change
With this setting, you can turn RIHD direct change over
HDMI on or off.
On (default): RIHD direct change on.
Off: RIHD direct change off.
Notes:
• The Direct Change setting can be set only when the
HDMI Control setting is set to On.
• When set to On, when playback is started on the
DPC-7.9, it will automatically be selected as the input
source on an RIHD-compatible TV or AV receiver.
• HDMI direct change only works with RIHD-compatible components that support it and may not work prop-
50
Select “Others” from the Disc
Menu Language, Audio Language, or Subtitle menu, and
then press [Enter].
The language code boxes appear.
Use the remote controller’s Left/
Right [ ]/[ ] buttons to select the
code boxes.
Use the Up/Down [ ]/[ ] buttons
to enter a language code.
See adjacent table for language codes.
When you’ve finished, press the
[Enter] button.
DPC-7.9_En.book Page 51 Tuesday, July 22, 2008 4:37 PM
Configuring the DPC-7.9—Continued
Language Code List
Use this list when specifying other languages.
Language
Japanese
English
French
German
Italian
Spanish
Chinese
Dutch
Portuguese
Swedish
Russian
Korean
Greek
Afar
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Bislama
Bengali
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
Bhutani
Esperanto
Estonian
Basque
Persian
Finnish
Fiji
Faroese
Frisian
Irish
Scots-Gaelic
Galician
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Code
JA
EN
FR
DE
IT
ES
ZH
NL
PT
SV
RU
KO
EL
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
BN
BO
BR
CA
CO
CS
CY
DA
DZ
EO
ET
EU
FA
FI
FJ
FO
FY
GA
GD
GL
GN
GU
HA
HI
HR
HU
HY
IA
IE
IK
IN
Language
Kirghiz
Latin
Lingala
Laothian
Lithuanian
Latvian
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay
Maltese
Burmese
Nauru
Nepali
Norwegian
Occitan
Oromo
Oriya
Panjabi
Polish
Pashto, Pushto
Quechua
Rhaeto-Romance
Kirundi
Romanian
Kinyarwanda
Sanskrit
Sindhi
Sangho
Serbo-Croatian
Sinhalese
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
Turkish
Tsonga
Code
KY
LA
LN
LO
LT
LV
MG
MI
MK
ML
MN
MO
MR
MS
MT
MY
NA
NE
NO
OC
OM
OR
PA
PL
PS
QU
RM
RN
RO
RW
SA
SD
SG
SH
SI
SK
SL
SM
SN
SO
SQ
SR
SS
ST
SU
SW
TA
TE
TG
TH
TI
TK
TL
TN
TO
TR
TS
Language
Icelandic
Hebrew
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Kashmiri
Kurdish
Code
IS
IW
JI
JW
KA
KK
KL
KM
KN
KS
KU
Language
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volap&uuml;k
Wolof
Xhosa
Yoruba
Zulu
Code
TT
TW
UK
UR
UZ
VI
VO
WO
XH
YO
ZU
51
DPC-7.9_En.book Page 52 Tuesday, July 22, 2008 4:37 PM
Troubleshooting
Symptom
Can’t turn
on the
DPC-7.9?
Possible cause
The power cord is not connected.
External interference is affecting the DPC-7.9’s
digital circuitry.
The wrong input source is selected on your TV.
The video cable is not connected properly.
On the European and Australian models, the PAL
Output Setting is set incorrectly for the connected
TV.
No HDMI Video Output?
The HDMI Output Setting is set to Off.
Your TV doesn’t support HDMI Resolution settings of 480i, 720p, 1080i, and 1080p.
No Component Video Output?
No picture?
Your TV does not support progressive scanning.
HD JPEG mode is on.
Remedy
Connect the power cord to a suitable wall outlet.
Turn off the DPC-7.9, wait five seconds, then try turning it on
again. If that fails, disconnect the power cord from the wall outlet, wait 10 seconds, reconnect it, then try turning it on again.
On your TV, select the input to which the DPC-7.9 is connected (page 24).
Check the video cable and correct as necessary (pages 19, 21).
Change the PAL Output Setting to the correct setting for the
TV.
Try pressing the [Resolution] button on the remote controller
repeatedly to switch the HDMI OUT on, and then pressing
the [Resolution] button repeatedly to get picture (page 25).
Press and hold down the Down [
] button, and then press
the [On/Standby] button to change the component video output to interlaced (page 46). Make sure the PRGV indicator is
not on.
When HD JPEG mode is on, no video is output by the COMPONENT VIDEO OUT.
No S-Video or Composite Video Output?
The Progressive setting is set to Progressive.
The Progressive setting is not set to interlaced.
Your TV is connected with S-video or composite
video and HD JPEG mode is selected.
The wrong input source is selected on your hi-fi
amp or AV receiver.
The audio cable is not connected properly.
The hi-fi amp or AV receiver connected to the
DPC-7.9’s audio outputs is not on.
The Digital/HDMI Audio Out setting is incorrect.
When set to Progressive, only the component video output
outputs video.
Press and hold down the Down [
] button, and then press
the [On/Standby] button to change the component video output to interlaced (page 46). Make sure the PRGV indicator is
not on.
HD JPEG mode can only be used with the HDMI OUT.
On your hi-fi amp or AV receiver, select the input to which
the DPC-7.9 is connected (page 20).
Check the audio cable and correct as necessary (page 19–21).
Turn on the hi-fi amp or AV receiver.
Check the Digital/HDMI Audio Out setting and correct as
necessary (page 47).
No Sound from the HDMI OUT?
The Digital/HDMI Audio Out setting is set to Off.
No sound?
The DVD player is connected to the DVI jack on
your TV or AV receiver.
The HDMI setting on your TV or AV receiver is set
to DVI.
Your TV or AV receiver doesn’t support Dolby
Digital.
Your TV or AV receiver doesn’t support DTS.
Your TV or AV receiver doesn’t support 96 kHz
PCM.
52
Change the Digital/HDMI Audio Out setting to either All or
PCM (page 47).
You won’t hear any sound from the HDMI output if the
source component is only DVI/HDCP-Compatible.
Change the HDMI setting on your TV or AV receiver to
HDMI.
Change the Digital/HDMI Audio Out setting to PCM (see
“Audio Formats” on page 22).
The DPC-7.9 will not be able to play DTS format audio or
soundtracks. On your DVD-Video disc’s audio setup menu,
select an audio format other than DTS (see “Audio Formats”
on page 22).
Change the Linear PCM Out setting to Down Sample On
(page 47).
DPC-7.9_En.book Page 53 Tuesday, July 22, 2008 4:37 PM
Troubleshooting—Continued
Symptom
No sound?
Possible cause
No Digital Audio Output?
The Digital/HDMI Audio Out setting is set to
Off.
Your TV or AV receiver doesn’t support Dolby
Digital.
Your TV or AV receiver doesn’t support DTS.
The source material is DTS and the Digital/
HDMI Audio Out setting is set to PCM.
The picture distorts
occasionally?
Picture instability or
noise?
Can’t start playback?
Can play CDs but not
DVDs?
Can play DVDs but not
CDs?
Can’t play MP3/WMA/
JPEG discs?
Can’t select MP3 files?
Remedy
Change the Digital/HDMI Audio Out setting to
either All or PCM (page 47).
Change the Digital/HDMI Audio Out setting to
PCM (page 47).
The DPC-7.9 will not be able to play DTS format
audio or soundtracks. On your DVD-Video disc’s
audio setup menu, select an audio format other
than DTS.
When the Digital/HDMI Audio Out setting is set to
PCM, DTS sources are not output by the digital
audio outputs. Change the setting to ALL.
Change the Linear PCM Out setting to Down Sample On (page 47).
Remove the disc and clean it (page 10).
A little picture distortion may occur when using
these functions. This is normal.
Your TV or AV receiver doesn’t support
96 kHz PCM.
The disc is dirty.
You’re using the Fast Forward or Fast Reverse
function.
The DPC-7.9 is connected to your TV via a
VCR or other video equipment and its copy
protection system is affecting the picture.
No discs loaded.
The selected disc cannot be played because
it’s incompatible.
The disc is upside down.
The disc is not centered in the disc bay.
The disc is dirty.
The selected disc has parental lock and the
Parental Lock function is on.
The Chain mode function is set to play only
CDs.
The Chain mode function is set to play only
DVDs.
The disc is not ISO9660 Level 2 format or
Joliet.
The disc has not been finalized.
MP3 files without a “.mp3” or “.MP3” filename extension are not recognized.
Load the disc the correct way up (page 26).
Place the disc in the center of the disc bay (page 26).
Remove the disc and clean it (page 10).
The sampling rate or bit-rate is not supported.
Use MP3 files that use the supported sampling
rates and bit-rates.
Connect the DPC-7.9 directly to your TV
(page 19).
Load some discs (page 26).
Load only compatible discs (page 8).
Turn off the Parental Lock function (page 49).
Change the Chain mode setting or cancel Chain
mode (page 36).
Change the Chain mode setting or cancel Chain
mode (page 36).
Use only ISO9660 Level 2 format or Joliet discs
(page 9).
Finalize the disc (page 9).
Use the correct filename extension (page 9).
WMA files without a “.wma” or “.WMA” filename extension are not recognized.
The WMA file’s copyright option is on.
JPEG files without a “.jpg” or “.JPG” filename
extension are not recognized.
Don’t use the copyright option (page 9).
The JPEG file is too big.
Use JPEG files that are less than 5 megabytes
(page 9).
The message “BAD DISC”
appears on the display?
The disc is dirty.
Remove the disc and clean it (page 10).
Buttons on the DPC-7.9
and remote controller
don’t work?
Power supply voltage fluctuations and other
anomalies, such as static electricity, can interfere with normal operation.
Turn off the DPC-7.9, wait five seconds, then turn
it on again. If that doesn’t resolve the issue, disconnect the power cord from the wall outlet, wait five
seconds, reconnect it, then try again.
Can’t play WMA files?
Can’t view JPEG files?
Use the correct filename extension (page 9).
Use the correct filename extension (page 9).
53
DPC-7.9_En.book Page 54 Tuesday, July 22, 2008 4:37 PM
Troubleshooting—Continued
There are no batteries in the remote controller.
The batteries are flat.
The batteries are installed incorrectly.
Buttons on the DPC-7.9
work OK but those on
the remote controller
don’t?
You’re not pointing the remote controller at
the DPC-7.9’s remote sensor.
You’re too far away from the DPC-7.9.
A strong light source is interfering with the
DPC-7.9’s remote sensor.
If the DPC-7.9 is installed in a cabinet with
colored glass doors, the remote controller may
not work reliably when the doors are closed.
The
cable is not connected properly.
The
work?
functions don’t
The DPC-7.9 is not connected with an analog
audio connection.
The HDMI Control setting is set to Off.
A component in your system does not support
CEC.
A component in your system has HDMI CEC
control turned off.
RIHD doesn’t work?
One of the components in your system does
not support CEC or is not connected correctly.
There’s a problem with the HDMI cable that
you’re using.
The DPC-7.9’s settings may be changed by
disconnecting and connecting the HDMI
cable.
An
cable is connected to the DPC-7.9.
54
Install new batteries (page 17).
Replace with new batteries (page 17).
Check the batteries and correct as necessary
(page 17).
Point the remote controller at the DPC-7.9’s
remote sensor (page 17).
Use the remote controller closer to the DPC-7.9
(page 17). The remote controller has a range of
approximately 16 ft. (5 meters).
Make sure that the DPC-7.9 is not subjected to
direct sunshine or inverter-type fluorescent lights.
Relocate if necessary.
Open the doors, or use a cabinet without colored
glass.
Make sure the
cable is connected properly.
To use
, you must make an
connection
and an analog audio connection (RCA) between
the DPC-7.9 and the AV receiver, even if they are
connected digitally.
Set the HDMI Control setting to On.
Refer to the component’s instruction manual to see
if it supports CEC.
Refer to the component’s instruction manual and
turn on HDMI CEC control.
Refer to the other component’s instruction manual
to see if it supports CEC and check your connections.
Try another HDMI cable.
Display a video manually on the TV.
Disconnect the
cable.
DPC-7.9_En.book Page 55 Tuesday, July 22, 2008 4:37 PM
Troubleshooting—Continued
■ Abnormal Behavior
The DPC-7.9 contains a microcomputer for signal processing and control functions. In very rare situations, severe
interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely even that this
should happen, unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in again.
Alternatively, press and hold the Stop [ ] button until “RESET” appears on the display (about 10 seconds).
■ Restoring the Default Settings
To reset the DPC-7.9 to its factory defaults, turn it on, and when “Integra DVD” has disappeared from the display,
while holding down the Stop [ ] button, press the [On/Standby] button. “INITIALIZE” appears on the display. When
the reset is complete, “COMPLETE” is displayed, and the DPC-7.9 enters Standby mode.
■ HDMI Status Mode
If you’re using an HDMI connection and there’s no picture or sound, you can check the status of the HDMI connection
by pressing and holding down the DPC-7.9’s [Display] button for 10 seconds until a message ID appears on the display.
Look up the message ID in the following tables and check the HDMI connections and settings on both the DPC-7.9 and
the connected component.
HDMI connection and HDMI-related settings status
Displayed ID
Message
MSG ID 001
MSG ID 005
MSG ID 015
Turn the DPC-7.9 and the connected component off, then turn them on again. Make sure that the
connected component is working properly and that the DPC-7.9’s HDMI settings are configured
suitably for that component.
No picture from the HDMI connection
Displayed ID
Message
MSG ID 002
The HDMI Output Setting is set to Off. Change it to On (page 46).
MSG ID 003
MSG ID 004
The HDMI cable may not be connected properly. Check the connection. Also, make sure the HDMI
input on the TV or AV receiver is correctly configured to received HDMI.
MSG ID 005
MSG ID 006
MSG ID 007
Make sure the HDMI input on the TV or AV receiver is correctly configured to received HDMI.
The connected component may not support HDCP. Make sure the connected component supports
HDCP.
Turn the DPC-7.9 and the connected component off, then turn them on again.
The DPC-7.9 may be connected to the other component’s DVI jack. Some TVs may not properly
receive the video output by the DPC-7.9. Also, with a DVI connection, there will be no sound.
MSG ID 008
The DPC-7.9’s HD Resolution setting is set to 480i or 720p or 1080i or 1080p. If your TV doesn’t
support these resolutions, select another resolution (page 25).
MSG ID 009
The connected component may not be receiving the HDMI signal properly.
Try selecting another resolution on the DPC-7.9 (page 25).
No sound from the HDMI connection
Displayed ID
Message
MSG ID 010
The DPC-7.9’s Digital/HDMI Audio Out setting is set to Off. Change the setting to All or PCM
(page 47).
MSG ID 011
MSG ID 014
The connected component may not support 96 kHz PCM. Set the DPC-7.9’s Linear PCM Out setting to Down Sample On (page 47).
MSG ID 012
MSG ID 013
The connected component may not support Dolby Digital. Set the DPC-7.9’s Digital/HDMI Audio
Out setting to PCM (page 47).
MSG ID 016
MSG ID 017
The connected component may not support DTS.
The DPC-7.9 cannot play the DTS format audio or soundtrack. On your DVD-Video disc’s audio
setup menu, select an audio format other than DTS.
55
DPC-7.9_En.book Page 56 Tuesday, July 22, 2008 4:37 PM
Specifications
Signal System
NTSC (North American model),
PAL/NTSC (European and Australian models)
Composite Video Output/Impedance
1.0 V(p-p)/75Ω negative sync, RCA
S-Video Output/Impedance
Y: 0.7 V(p-p)/75Ω negative sync, 4-pin mini DIN,
C: 0.286 V(p-p)/75Ω
Component Video Output/Impedance
Y: 1.0 V(p-p)/75Ω, PB/PR: 0.7 V(p-p)/75Ω, RCA/BNC
DVD Linear Audio
4 Hz–44 kHz (96 kHz), 4 Hz–22 kHz (48 kHz)
Audio CD
4 Hz–20 kHz (44.1 kHz)
Signal to Noise Ratio
95 dB
Audio Dynamic Range
95 dB
THD (Total Harmonic Distortion)
0.007% (1 kHz)
Wow and Flutter
Below threshold of measurability
Audio Output
Audio Output/
Impedance
Audio Output/
Impedance
Power supply
Digital
Optical
Digital
Coaxial
–22.5 dBm
0.5 V (p–p), 75 Ω
Analog
2.0 V (rms), 540 Ω
North American model
AC 120 V, 60 Hz
European and Australian models
AC 100–240 V, 50 Hz
Power Consumption
15 W
Stand-by Power Consumption
0.5 W
Dimensions (W x H x D)
435 X 131 X 436 mm (17-1/8&quot; X 5-3/16&quot; X 17-3/16&quot;)
Weight
6.3 kg (13.9 lbs.)
Operating Conditions Temperature/Humidity
5&deg;C–35&deg;C (41&deg;F–95&deg;F) / 5%–85%
Disc compatibility
AUDIO CD, DVD-VIDEO, MP3, WMA, CD-R and RW,
DVD-R/RW/R DL, DVD+R/RW/R DL (DVD-Video), JPEG-CD
Disc that have not been property finalized may only be partially playable or not playable at all.
Specifications and features subject to change without notice.
Integra Division of
ONKYO U.S.A. CORPORATION
18 park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 201-818-9200 Fax: 201-785-2650 http://www.integrahometheater.com
Integra Division of
ONKYO CORPORATION
Sales &amp; Product Planning Div.: 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8163
En
I0807-1
SN 29344789
(C) Copyright 2008 ONKYO CORPORATION Japan. All rights reserved.
56
* 2 9 3 4 4 7 8 9 *
">
Hello! I am an AI chatbot specifically trained to assist you with the Integra DPC-7.9 Blu-ray / DVD Player Owner Manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!
Assistant typing
Assistant terminated
Related

Onkyo DVD Player DV-HD805 User manual

Integra DPC-7.9 Blu-ray / DVD Player Owner Manual

Onkyo C-7030 Instruction Manual

Integra DPC-7.9 DVD Changer Instruction Manual | Online PDF

Integra DPC-7.5 Blu-ray / DVD Player Instruction manual

Onkyo C 7030 Instruction Manual

Integra DPC-7.4 Blu-ray / DVD Player Instruction manual

Integra DPC-5.2 Blu-ray / DVD Player Instruction manual

Integra DPC-6.1 Blu-ray / DVD Player Instruction manual

Integra DPC-7.7 Blu-ray / DVD Player Instruction manual

Integra DPC-8.5 Blu-ray / DVD Player Instruction manual

Integra DPS-6.7 Blu-ray / DVD Player Instruction manual
