PRINCE SERIE
USER'S MANUAL
PRINCE SERIE
ASH-09AP, ASH-12AP
Thank you for choosing SINCLAIR air conditioner. For correct operation, please read this owner manual
carefully before operating the unit and keeps it carefully for consultation.
CONTENTS
Operation and maintenance
Notices for operation ...
■ .............................1
■ ................................3
Notices for operation
Names and functions of each part ...
■ ...................4
Operation of wireless remote control .....................5
■ Emergency operation ..............................10
■ Clean and care
■ ...................................11
■ ...................................13
Troubleshooting
Installation service
Notices for installation
■ ...............................16
Installation dimension diagram .........................18
■ ■ ...............................19
Install indoor unit ...
Install outdoor unit ...
■ ..............................21
Test operation and check after installation
■ .................23
The figures in this manual may be different with the material objects, please refer
to the material objects for reference.
This symbol stands for the items
should be forbidden
This symbol stands for the items
should be followed
Do not dispose this product as unsorted municipal waste.
Collection of such waste separately for special treatment
is necessary.
Notices for operation
Please read the following carefully before operating
★ When the voltage
is very high, the
components would be easily
damaged, when the voltage
is very low, the compressor
vibrates terribly and that the
refrigerant system will be
damaged, the compressor
and electric components
cannot work, the voltage
should be stable; there
shouldn’t be big fluctuation.
★ Don’t leave windows
and doors open for
a long time while operating
the air conditioner.
It can decrease the air
conditioning capacity.
★ When having a
burning smell or
smoke, please turn off the
power supply and contact
with the service center.
If the abnormity still exists,
the unit may be damaged,
and may cause electric
shock or fire.
★ Be sure to pull out
the power plug as
the air conditioner not in use
for a long time.
Otherwise, the accumulated
dusts that may cause over
heating or fire.
Never splice the
power cord or use
an extended cord.
It can cause overheating or
fire.
★ Don't block the air
★ The power supply
must adopt the
intake or outlet vents
of both the outdoor and indoor special circuit that with air
units.
switch protection and assure
It can decrease the air conditioning it has enough capacity.
capacity or cause a malfunction.
The unit will be turned
on or off according to your
requirement automatically,
please do not turn on or turn
off the unit frequently, otherwise disadvantage effect may
be caused to the unit.
★Keep combustilble
spray away from the
units more than 1m.
★ Don’t attempt to
repair the air
conditioner by yourself.
The wrong repair will lead to
It can cause a fire or explosion an electric shock or fire, so
you should contact the service
center to repair.
1
Notices for use
★ Please don't cut off or damage the
power cords and control cords.
If they are damaged, please ask the qualified
personnel to change them.
★ To adjust the airflow direction
appropriately. At operating,the
louvers of air conditioner could be adjusted
by pressing the SWING button on wireless
remote control to change the airflow direction.
Swing louver
★ Don’t insert your hands or stick into
the air intake or outlet vents.
Guide louver
★
Don’t blow the wind to animals
and plants directly. It can cause
a bad influence to them.
★ Don’t use the air conditioner
★ Don’t apply the cold wind to
the body for a long time.
It can cause the health problems.
for other purposes, such as
drying clothes, preserving foods, etc.
★ Splashing water on the air
★ Don’t place a space heater
conditioner can cause an electric
shock and malfunction.
2
near the air conditioner.
Notices for operation
Working principle and special functions for cooling
Principle:
Air conditioner absorbs heat in the room and transmit to outdoor and discharged,
so that indoor ambient temperature decreased, its cooling capacity will increase
or decrease by outdoor ambient temperature.
Anti-freezing function
If the unit is running in COOL mode and in low termperature, there will be frost formed
on the heat exchanger, when indoor heat exchanger temperature decreased below 0
the indoor unit microcomputer will stop compressor running and protect the unit.
Working principle and special functions for heating
Principle:
* Air conditioner absorbs heat in the room and transmit to outdoor and discharged,
will increase, its heating capacity will decrease by outdoor ambient temperature.
so that indoor ambient temperature increased, so room heating capacity.
* If outdoor temperature got lower, please operate with the other heating ventilating
equipments.
Defrosting:
* When outdoor temperature is low but high humidity, after a long while running,
frost will form on outdoor unit, that will effect the heating effect, at this time,
the auto defrosting function will act, the heat running will stop for 8-10mins.
* During the auto defrosting, the fan motors of indoor unit and outdoor unit will stop.
* During the defrosting, the indoor indicator flashes, the outdoor unit may emit vapor.
This is due to the defrosting, it isn't malfunction.
* After defrosting finished,the heating will recover automatically.
Anti-freezing function:
In "HEAT" mode, if in the following status, the indoor heat exchanger haven't achieve
the certain temperature, that the indoor unit will not act, in order to prevent cool air blowing.
(Within 3mins)
1.Heating starts. 2.After Auto defrosting finished. 3.Heating under the low temperature.
The climate type of this unit is according to the nameplate.
3
Names and functions of each part
Indoor unit
Air in
⑵
⑴
⑶
⑷
Air out
⑹
⑸
⑴ Manual switch
⑼
⑵ Front panel
⑶ Filter
⑷ Guide louver
⑸ Receiving window
⑹ Bind tape
Outdoor unit
⑺ Connection wire
⑻Drainage pipe
Air in
⑼ Remote control
⑺
⑻
Air out
4
遥控器各按键的名称及作用
Operation of wireless remote control
Name and function of wireless remote control
Note: Besure that there are no obstructions between receiver and remote controoler;
Don't drop or throw the remote control; Don't let any liquid in the remote control and
put the remote control directly under the sunlight or any place where is very hot.
Signal transmitter
SLEEP
SLEEP button
● Press this button, Sleep On and Sleep
Off can be selected. After powered on,Sleep
Off is defaulted. After the unit is turned
off, the Sleep function is canceled. After
Sleep function set up, the signal of Sleep
will display. In this mode, the time of timer
can be adjusted. Under Fan and Auto
modes, this function is not available.
FAN
FAN button
● Press this button, Auto, Low, Middle, High
speed can be circularly selected. After
powered on,Auto fan speed is default.
Under Blow mode, Low fan speed only
can be set up.
Remote control
Low fan
Middle fan
High fan
ON/OFF
CLOCK
ON/OFF button
● Press this button, the unit will be turned
signal blink and display.Within 5
seconds, the value can be adjusted by
pressing + or - button, if continuously
press this button for 2 minutes above,
in every 0.5 seconds, the value on ten place
of Minute will be increased 1. During blinking,
repress the Clock button or Confirm button,
signal will be constantly displayed and
it denotes the setting succeeded. After
powered on, 12:00 is defaulted to display
and signal will be displayed. If there is
signal be displayed that denotes the
current time value is Clock value, otherwise
is Timer value.
on, press it once more, the unit will be
turned off. Sleep function will be canceled,
while unit off.
MODE
CLOCK button
● Press this button, the clock can be set up,
MODE button
● Press this button, Auto, Cool,Dry, Fan,
Heat mode can be selected circularly.
Auto mode is default while power on.
Under Auto mode,the temperature will not
be displayed; Under Heat mode, the
o
initial value is 28℃( 82 F);Under other
modes, the initial value is 25℃( 77 oF).
AUTO
COOL
DRY
FAN
HEAT
(only for cooling and heating unit)
5
Operation of wireless remote control
Names and functions of wireless remote control
This wireless remote control is universal, and it could be used for many units, some
buttons of this control which are not available to this unit will not be described below.
+
+ button
● Presetting temperature can be increased.
Press this button, the temperature can be
set up, continuously press this button
and hold for two seconds, the relative
contents can quickly change, until unhold
this button and send the order that the ℃
(oF) signal will be displayed all the time.
The temperature adjustment is unavailable under the Auto mode, but the order
can be sent if pressing this button.
Temperature of Celsius degree setting:
16-30 ; for Fahrenheit degree setting:
61-86.
Remote control
-
- button
● Presetting temperature can be decreased.
BLOW
Press this button, the temperature can be
set up, continuously press this button
and hold for two seconds, the relative
contents can quickly change, until unhold
this button and send the order that the ℃
(oF) signal will be displayed all the time.
The temperature adjustment is unavailable under the Auto mode, but the order
can be sent by if pressing this button.
BLOW button
● Press this button, the Blow On and Blow
Off can be set up. Under the Cool and Dry
mode, press this button once, the signal
"DRY" will be displayed, and BLOW is
turned on; When repressing this button
once more, signal "DRY" will be concealed,
at this time, the BLOW is turn off. After
powered on, Blow Off is defaulted. If
operating ON/OFF button and changing
mode to Cool, Dry, the status of BLOW
will stay in the original position. If unit
is off, only Blow off can be set up and send
the signal. This function is not available
under the Auto, Fan and Heat mode
and there is no Blow signal displayed.
TURBO
LIGHT
LIGHT button
● Press this button at unit On or Off status,
Light On and Light Off can be set up.
After powered on, Light On is defaulted.
TURBO button
● Under Cool or Heat mode, press this
button can turn on or turn off the Turbo
function.After the Turbo function turned
on, the signal of Turbo will display. The
signal will be automatically cancelled if
changing the mode or fan speed.
6
Operation of wireless remote control
Names and functions of wireless remote control
This wireless remote control is universal, and it could be used for many units, some
buttons of this control which are not available to this unit will not be described below.
TIMER ON
TIMER ON BUTTON
●
Remote control
SWING UP AND DOWN BUTTON
●
Timer On setting: Signal “ON” will blink
and display, signal
will conceal, the
numerical section will become the timer
on setting status. During 5 seconds blink,
by pressing + or - button to adjust the
time value of numerical section, every
press of that button, the value will be
increased or decreased 1 minute. Hold
pressing + or -button, 2 seconds later,
it quickly change, the way of change is:
During the initial 2.5 seconds, ten numbers
change in the one place of minute, then
the one place is constant, ten numbers
change in the tens place of minute at 2.5
seconds speed and carry. During 5s blink,
press the Timer button, the timer setting
succeeds. The Timer On has been set up,
repress the timer button, the Timer On
will be canceled. Before setting the
Timer, please adjust the Clock to the
current actual time.
TIMER OFF
TIMER OFF BUTTON
Press this button to set swing angle,
●One press this key to enter into
which circularly changes as below:
TIMER OFF setup, in which case
the TIMER OFF icon will blink.
The method of setting is the same
as for TIMER ON.
OFF
This remote controller is universal.If it
receives threes kinds of following status,
the swing angle will remain original.
If guide louver is stopped when it is
swinging up and down,it will remian its
present position.
indicates guide louver swings back and
forth in the five places,as shown in the
figure.
7
Operation of wireless remote control
Guide for operation- general operation
1. After powered on, press ON/OFF button, the unit will start to run.(Note: When
it is powered on, the guide louver of main unit will close automatically.)
2. Press MODE button, select desired running mode, or press COOL or HEAT
mode to enter into the corresponding operation directly.
3. Pressing +or - button, to set the desired temperature (It is unnecessary
to set the temp. at AUTO mode.)
4. Pressing FAN button, set fan speed, can select AUTO FAN, LOW, MID
and HIGH.
5. Pressing
button, to select the swing.
Guide for operation- Optional operation
1. Press SLEEP button, to set sleep.
2. Press TIMER ON and TIMER OFF button, can set the scheduled timer on
or timer off.
3. Press LIGHT button, to control the on and off of the displaying part of the
unit (This function may be not available for some units).
4. Press TURBO button, can realize the ON and OFF of TURBO function
Introduction for special function
★ About blow function
This function indicates that moisture on evaporator of indoor unit will be blowed after the unit
is stopped to avoid mould.
1. Having set blow function on: After turning off the unit by pressing ON/OFF button
indoor fan will continue running for about 10 min. at low speed. In this period,
press blow button to stop indoor fan directly.
2. Having set blow function off: After turning off the unit by pressing ON/OFF button,
the complete unit will be off directly.
★ About AUTO RUN
When AUTO RUN mode is selected, the setting temperature will not be displayed on the
LCD, the unit will be in accordance with the room temp. automatically to select the suitable
running method and to make ambient comfortable.
★ About turbo function
If start this function, the unit will run at super-high fan speed to cool or heat quickly so that
the ambient temp. approachs the preset temp. as soon as possible.
8
Operation of wireless remote control
★ About lock
Press +and - buttons simultaneously to lock or unlock the keyboard. If the remote controller
will be displayed on it, in which case, press any button, the mark will
is locked, the icon
flicker for three times. If the keyboard is unlocked, the mark will disappear.
★ About swing up and down
1. Press swing up and down button continuously more than 2s,the main unit will swing back
and forth form up to down, and then loosen the button, the unit will stop swinging and present
position of guide louver will be kept immediately.
2. Under swing up and down mode, when the status is switched from off to , if press this
button again 2s later,
status will switch to off status directly; if press this button again
within 2s,the change of swing status will also depend on the circulation sequence stated above.
★ About switch between Fahrenheit and Centigrade
Under status of unit off, press +and - buttons simultaneously to switch ℃ and .
★ About new function of defrosting
It indicates: after starting this function by remote controller and the unit has been under
defrost status, If turn off the unit by remote controller, the unit will not stop defrosting until
it is finished; if change setting mode by remote controller, the function ,which is set last
time, won't be carried out until defrosting finished.
Operation of this function on or off: If remote controller is under off status, press mode button
and blow button simultaneously in order to enter or cancel this new function. If the unit is under
defrost mode, dual eight position on remote controller will display H1.If switch to heat mode,
the position will display H1, which flickers for 5s, in which case, press +/- button, H1 will
disappear and setting temp. be displayed.
After remote controller is powered on, the new defrost function will be defaulted to be closed.
Changing batteries and notices
The wireless remote control adopts two new AAA1.5V dry batteries.
1.Slide the cell cover downward to take out the worn cells, then
Battery cover
change 2 new ones (note to the correct polarity).
2.Cover the cell cover.
★ NOTE:
● When changing the batteries, do not use the old or different batteries,
otherwise, it can cause the malfunction of the wireless remote control.
● If the wireless remote control will not be used for a long time, please
take them out, and don't let the leakage liquid damage the wireless
remote control.
● The operation should be in its receiving range.
● It should be placed at where is 1m away from the TV set or stereo sound sets.
● If the wireless remote control can not operate normally, please take them out,
after 30s later and reinsert, if they cannot normally run, please change them.
9
Sketch map for
changing batteries
Emergency Operation
Emergency Operation
When the wireless remote control is lost or damaged, please use the manual switch, at
this time, it is running in Auto Run mode that will not change the temperature setting
value and fan speed.
The manual switch can be operated as follow:
●
●
At operation: When the unit stopped running,
press ON/OFF button, unit will enter into AUTO
RUN mode. The microcomputer will accord to
the room temperature to select the (COOL,
HEAT, FAN) mode automatically, to obtain the
comfortable effect.
AUTO/STOP
Manual Switch
At stopping:When the unit is running, press the
ON/OFF button of the manual switch, the unit
will stop work.
The code swich can be operated as follow:
●
●
At operation: When the unit is stopped running,
adjust the code switch to AUTO, the unit will
enter into AUTO RUN mode. The microcomputer
will accord to the room temperature to select the
(COOL, HEAT, FAN) mode automatically, to
obtain the comfortable effect.
At stopping: When the unit is running, adjusts
the code switch to STOP position, the unit will
stop work.
10
Code Switch
Clean and care
CAUTION
●
●
●
Turn power off and pull out the power plug before cleaning air conditioner. Or it may
cause electric shock.
Never sprinkle water on the indoor unit and the outdoor unit for cleaning because it
can cause an electric shock.
Volatile liquid (e.g. thinner or gasoline) will damage the air conditioner. (So wipe the
units with a dry soft cloth, or a cloth slightly moistened with water or cleanser.)
Clean the front panel(make sure to take it off before cleaning)
①
Take off the front panel
Along the direction of arrows to lift the front panel
up, meanwhile to hold both slots of the front panel
and take it out forcibly and then can take it off.
② Washing
Clean with a soft brush, water and neutral detergent,
and then to dry it.(Note: Never use the water above
45 ℃ to wash the panel, or it could cause deformation
or discolouration.)
③ Install front panel
Place two supporters of the front panel into the slots,
along the direction of arrows to cover and clasp the
front panel. As show in righ figure.
Cleaning the air filters (Recommended once every three months)
Note: If dust is much more around the air conditioner, the air filters should be cleaned many
times. After taking off the filter, don't touch the fin of indoor unit, in order to avoid hurt your
fingers.
11
Clean and care
① Take down the air filter
At the slot of surface panel to open an angle, pull the
air filter downward and take it out.
(b)
② Cleaning
To clean the dust adhering to the filters, you can either
use a vacuum cleaner, or wash them with warm water
(the water with the neutral detergent should below 45 ℃).
When the filters are very dirty (such as oil stain), and
dry it in the shade.
NOTE: Never use water above 45 ℃ to wash, or it can
cause deformation or discoloration. Never partch it by
fire, or can cause a fire or deformation.
③
Reinsert the filters
Reinsert the filters along with the arrow head, then cover
the surface panel and clasp it.
Check before use
①
Be sure that nothing obstructs the air outlet and intake
vents.
②
Check that whether ground wire is properly connected
or not.
③ Check that whether the batties of air conditioner are
changed or not.
④
(a)
Check that whether the installation stand of the outdoor
unit is damaged or not. If damaged, please contact the dealer.
Maintain after use
① Turn main power off.
② Clean the filter and indoor and outdoor units' bodies.
③ Repaint the rubiginous place on the outdoor unit to prevent it from spreading.
12
Troubleshooting
Warning
Do not repair the air conditioner at your discretion. Incorrect repair may cause electric
shock or fire, so please contact Authorized Service Center for professional repair.
Following checks prior to contact may save your time and costs.
Troubleshooting
Phenomenon
Air conditioner does not run upon immediately
restart after a stop.
● To
protect the air conditioner upon
immediate restart after a stop, the
microcomputer controller will delay
the unit for 3 minutes before the air
conditioner will run.
Wait
Air conditioner blows out bad smell when
it is initially started.
The air conditioner itself has no bad smell.
If any. It is the bad smell accumulated from
environment. Solution: Clean the air filter.
●
● If
still any problem, the air conditioner shall
be cleaned (Please contact Authorized
Service Center)
You may hear “Water Flowing” noise
when the air conditioner is running.
Sometimes a thin fog will flow out of the
outlet when air conditioner is running
under cooling mode.
You may hear a slight crack when the
air conditioner is started or stopped.
● When
the air conditioner is started, or the
compressor is started or stopped during
running or the air conditioner is stopped,
sometimes you may hear “hua-hua” or “di-di-”
noise. This is the flowing sound of refrigerant
other than fault.
●
●
This might occur when indoor temperature
and humidity are high. This is because the
indoor air is quickly cooled down.
After a period of time, the fog will disappear
with the decrease of indoor temperature
and humidity.
This is the sound of friction caused by
expansion of panel or other parts due
to the change of temperature.
13
Troubleshooting
Phenomenon
Troubleshooting
●
The unit can not run
Has the power been shut down?
● Dose
●
Break off
Cooling(Heating) efficiency is not good.
power plug come loose from the socket?
Is the circuit protection device tripped off or not?
●
Is voltage higher or lower?
(Tested by professionals)
●
Is the Timer correctly used?
Is Temp. setting suitable?
Were inlet and outlet vents obstructed?
● Is there too much dusts accumulated and
obstructed the filter?
● Are the windows and doors clothed?
● Did Fan speed set at low speed?
● Is there any heat sources in the room?
●
●
Wireless remote control is not available
If water leakage in the room
● The
unit is interfered by abnormal or frequent
functions switchover occasionally the controller
cannot operate. At this time, you need to pull
out of the plug, and reinsert it.
●
Is it in its receiving range? Or obstructed?
To check the voltage in wireless remote control
inside is charged, otherwise to replace the
batteries.
●
Whether the wireless remote control is damaged.
The air humidity is on the high side.
Condensing water over flowed.
● The connection position of indoor unit drainage
pipe is loosed.
●
●
If water leakage in outdoor unit
●
Noise from indoor unit emitted.
● The sound of fan or compressor relay is switching
When the unit is running in COOL mode, the
pipe and connection of pipe would be condensed
due to the water cooled down.
● When the unit is running in Auto Defrosting mode,
the ice thawed and flowed out.
● When the unit is running in HEAT mode, the
water adhered on heat exchanger dripped off.
on or off.
● When
the defrosting is started or stop running,
it will sound. That is due to the refrigerant flowed
to the reverse direction.
14
Troubleshooting
Troubleshooting
Phenomenon
Indoor unit cannot deliver air
Moisture on air outlet vent
In HEAT mode, when the temperature of
indoor heat exchanger is very low, that
will stop deliver air in order to prevent cool
air. (Within 3min)
● In HEAT mode, when the outdoor temperature
is low or high humidity, there are much frost
be formed on the outdoor heat exchanger,
that the unit will automatically defrost, indoor
unit stop blowing air for 8-10min.During the
defrosting, there is water flowing out or vapor
be produced.
●
●
In dehumidifying mode, sometimes indoor
fan will stop, in order to avoid condensing
water be vaporized again, restrain temperature rising.
●
If unit is running under the high humidity for
a long time, the moisture will be condensed
on the air outlet grill and drip off.
Immediately stop all operations and plug out, contact
the dealer in following situations.
There is harsh sound during operation
The terrible odors emitted during operation
Water is leaking in the room
Air switch or protection switch often breaks
Carelessy splash water or something into unit
There is an abnormal heat in power supply cord
and power plug.
15
Stop running and pull out of the plug.
Installation service- Notices for installation
Important Notices
1. The unit installation work must be done by qualified personnel according to the local
rules and this manual.
2. If the air conditioner has not plug, directly connect it into the fixed circuit, a breaker should be
installed in the fixed circuit. all pole of this breaker should be switching off and the distance
of the contact should be at least 3mm.
Basic Requirements For Installation Position
Install in the following place may cause malfunction. If it is unavoidable contact with
service center please:
● Place
where strong heat sources, vapors, flammable gas or volatile objuct are emitted
where high-frequency waves are generated by radio equipment, welders and
medical equipment.
● Place where a lot of salinities such as coast exists.
● Place where the oil (machine oil) is contained in the air.
● Place
●
Place where a sulfured gas such as the hot spring zones is generated.
place with special circumstance.
● Other
Indoor Unit Installation Position Selection
1. The air inlet and outlet vent should be far from the obstruction, make sure that the air
can be blown through the whole room.
2. Select a position where the condensing water can be easily drained out, and the place
is easily connected for outdoor unit.
3. Select a location where the children can not reach.
4. Can select the place where is strong enough to withstand the full weight and vibration of
the unit. And will not increase the noise.
5. Be sure to leave enough space to allow access for routine maintenance. The height of the
installed location should be 230 cm or more from the floor.
6. Select a place about 1m or more away from TVset or any other electric appliances.
7. Select a place where the filter can be easily taken out.
8. Make sure that the indoor unit installation should accord with installation dimension
diagram requirements.
Outdoor Unit Installation Position Selection
1. Select a location from which noise and outflow air emitted by unit will not inconvenience
neighbors, animals, plants.
2. Select a location where there should be sufficient ventilation.
3. Select a location where there should be no obstructions cover the inlet and outlet vent.
4. The location should be able to withstand the full weight and vibration of the outdoor unit
and permit safe installation.
5. Select a dry place, but do not expose under the direct sunlight or strong wind.
6. Make sure that the outdoor unit installation dimension should accord with installation
dimension diagram, convenient for maintenance, repair.
7. The height difference of connecting the tubing within 5m, the length of connecting the
tubing within 10m.
8. Select a place where it is out of reach for the children.
9. Select a place where will not block the passage and do not influence the city appearance.
16
Notices for installation
Safety Requirements For Electric Appliances
1. The power supply should be used the rated voltage and AC exclusive circuit,
the power cable diameter should be satisfied.
2 Don't drag the power cable emphatically.
3
It should be reliably earthed, and it should be connected to the special earth device,
the installation work should be operated by the professional.
The air switch must have the functions of magnetic tripping and heat tripping, in order
to protect the short circuit and overloading.
4. The min. distance from the unit and combustive surface is 1.5m.
Note:
●
Make sure that the Live wire or Zero line as well as the earth wire in the family power
socket can not be wrong connected, there should be reliable and no short circuit in the
diagram.
●
wrong connection may cause fire.
Earthing requirements
1. Air conditioner is type 1 electric appliance, thus please do conduct reliable earthing
measure.
2. The yellow-greentwo-colorwireinairconditioner is earthing wire and cannot be used
for other propose. It cannot be cut off and be fix it by screw, otherwise it would cause
electric shock.
3. The earth resistance should accord to the National Criterion.
4. The user power must offer the reliable earthing terminal. Please don't connect the
earthing wire with the following place:
① Tap water pipe ② Gas pipe
③ Contamination pipe ④ Other places that professional personnel consider them unreliable.
Others
1.The connection method of unit and power cable as well as the interconnect method
of each isolated component should refer to the circuit diagram stick on the unit.
2.The model of the blown fuse and rated value should refer to the silk-screen on the
controller or fuse sleeve.
3. The appliance shall be installed in accordance with national wiring regulations.
4. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
5. Children should be supervised to ensure that they do not play with the appliance.
17
Installation dimension diagram
Installation dimension diagram
15
cm
Space to the ceiling
Above
15cm Above
15cm Above
Space to the wall
Space to the wall
300
cm
230
2
cm
Above
Above
Air outlet side
Air inlet side
30
c
mA
bo
ve
Space to the obstruction
50cm Above
Space to the floor
30cm Above
0c
mA
bo
ve
50cm Above
20
Space to the wall
Air outlet side
18
Install indoor unit
Install the rear panel
1.Always mount the rear panel horizontally. As the water drainage pipe at the left, when adjusting the rear
panel, this side should not be too high; the right side should be slightly high.
2. Fix the rear panel on the selected location Wall
3. Be sure that the rear panel has been
fixed firmly enough to withstand the weight
of an adult of 60kg, furthermore, the weight
should be evenly shared by each screw.
Space to
the wall
150mm
above
Space to
the wall
150mm
above
Left
(Rear piping hole)
Wall
Gradienter
Mark on the middle of it
Fig.1
Right
(Rear piping hole)
Install the piping hole
1. Make the piping hole in the wall at a slight downward slant to the outdoor
Indoor
side.
2. Insert the piping-hole sleeve into the hole to prevent the connection Wall pipe
piping and wiring from being damaged when passing through the hole.
Outdoor
Seal pad
Install the water drainage pipe
1. For well draining, the drain hose should be placed at a
downward slant.
2. Do not wrench or bend the drain hose or flood its end
by water.
3. When the long drainage hose passing through indoor,
should wrap the insulation materials.
Wrenched
Bent
Flooded
Connect indoor and outdoor electric wires
1. Open the front panel upwardly.
2.Screw off the fixing screw of cover plate and screw off cover plate.
3. Put the power connection cable through the back of indoor unit wire hole and take it out.
4. All the wiring should be connected according to the circuit diagram on the unit.
5. Put the power connection cable the section, which with sheath into wire groove, and
cover the cover plate, screw on the fixing screw, tighten the connection wire.
6. Cover the front panel cover.
7. For the cooling and heating unit, signal control wire can be passed through the connection
of connector and indoor unit, and use the wire clip that is under the body case, tighten the
signal control wire.
19
Install indoor unit
NOTE:
When connecting the electric wire if the wire length is not enough, please contact with
the authorized service shop to buy a exclusive electric wire that is long enough and the
joint on the wire are not allowed.
The electric wiring must be correctly connected, wrong connection may cause spare
parts malfunction.
● Tighten the terminal screw in order to prevent loose.
● After tighten the screw, slightly pull the wire and confirm whether is it firm or not.
● If the earth wire is wrong connection, that may cause electric shock.
● The cover plate must be fixed, and tighten the connection wire, if it is poor installed, that
the dust, moisture may enter in or the connection terminal will be affected by outside force,
and will cause fire or elelctric shock.
● Leakage circuit-breaker and air switch of correct capacity must be installed.
●
Install the indoor unit
External connection
Gas side piping electric wire
Liquid side
piping
● The
piping can be lead out from right, right rear,
left, left rear.
When
routing the piping and wiring from the left
1.
or right side of indoor unit, cut off the tailings
from the chassis in necessary (show in Fig.2)
(1).Cut off the tailings 1 when routing the wiring only;
(2).Cut off the tailings 1 and tailings 2 when routing
both the wiring and piping.(or 1,2,3);
2.Take out the piping from body case, wrap the piping
electric wire, water pipe with tape and put them through the piping hole (As show in Fig. 3)
Tailing 3
Tailing 2
Tailing1
Fig.2
Liquid side
Gas side piping
piping
insulation
Finally wrap it
insulation
with tape Water drainage pipe
Fig.3
Left
Right
Right rear
Left rear
Fixing hook
Mounting
board
3.Hang the mounting slots of the indoor unit on the
upper tabs of the rear panel and check if it is firm
enough. (As show in Fig.4)
Mounting
board
Fig.4
Install the connection pipe
1.Align the center of the piping flare with the relevant valve.
2.Screw in the flare nut by hand and then tighten
the nut with spanner and torque wrench refer
to the following.
Tightening torque table
Hex nut diameter
Tightening torque(N·m)
Ф6
Ф 9.52
Ф 12
Ф 16
Ф 19
15~20
31~35
50~55
60~65
70~75
Indoor unit piping
Spanner
Taper nut
Piping
Torque wrench
NOTE: Firstly connect the connection pipe to indoor unit, then to outdoor unit; pay attention
to the piping bending, do not damage the connection pipe; the joint nut couldn't tighten too
much, otherwise it may cause leakage.
20
Install outdoor unit
Electric Wiring
1. Disassemble handle of right side plate or front side plate of outdoor unit.
2. Take off wire clamp, connect and fix power connect cord to terminal of line bank.
Wiring should fit that of indoor unit.
3. Fix the power connection cable with wire clamp, for cooling and heating unit, then use the
wire clamp to fix the signal control wire, then connect the corresponding connector.
4. Ensure if wire has been fixed well.
5. Install handle or front side plate.
NOTE:
●
Wrong wiring may cause spare parts malfunction.
●
After the cable fixed, make sure there should be a free space between the connection and
fixing place on the lead wire.
Air purging and leakage test
● Air purging and leakage test
1. Connect charging hose of manifold valve to charge end of low
pressure valve (both high/low pressure valves must be tightly
shut).
2. Connect joint of charging hose to vacuum pump.
3. Fully open handle handle of Lo manifold valve.
4. Open the vacuum pump to evacuate. At the beginning, slightly
loosen joint nut of low pressure valve to check if there
is air coming inside.
5. After finishing evacuation, shut Lo handle of manifold
valve to stop the vacuum pump. (Keep evacuating for
more than 15 minutes and make sure the reading of
multi-meter is -1.0 10 5pa(-76cmHg)
6. Fully open high/low pressure valves.
7. Remove charging hose from charging end of low
pressure valve.
8. Tighten bonnet of low-pressure valve. (As shown in Fig.5)
21
Liquid pipe
Gas pipe
Valve
cap
Vacuum pump
Fig.5
Vacuum
gauge
Install outdoor unit
● Leak hunting
Indoor unit check point
Use soap water or leak hunting meter to check whether
the joints is leak.
Indoor unit check point
Fig.6
Outdoor condensation drainage (Heat pump type only)
When the unit is heating, the condensing water
and defrosting water can be drained out reliably
through the drain hose.
Installation: Install the outdoor drain elbow in
Ø 25 hole on the base plate, and joint the
drain hose to the elbow, so that the wastewater
formed in the outdoor unit can be drained out
to a proper place.
22
Chasis
Outdoor drain
elbow
Check after installation and test operation
Check after installation
Items to be checked
Possible malfunction
Has it been fixed firmly?
The unit may drop, shake or emit noise.
Have you done the refrigerant leakage test?
It may cause insufficient cooling(heating)
capacity.
Is heat insulation sufficient?
It may cause condensation and dripping.
Is water drainage well?
It may cause condensation and dripping.
Is the voltage in accordance with the rated
voltage marked on the nameplate?
It may cause electric malfunction
or damage the part..
Is the electric wiring and piping
connection installed correctly and securely?
It may cause electric malfunction
or damage the part.
Has the unit been connected to a secure
earth connection?
It may cause electrical leakage.
Is the power cord specified?
It may cause electric malfunction
or damage the part
Is the inlet and outlet been covered?
It may cause insufficient cooling(heating)
capacity.
Has the length of connection pipes
and refrigerant capacity been recorded?
The refrigerant capacity is not accurate.
Test Operation
1. Before test operation
(1) Do not switch on power before installation isfinished completely.
(2) Electric wiring must be connected correctly and securely.
(3) Cut-off valves of the connection pipes should be opened.
(4) All the impurities such as scraps and thrums must be cleared from the unit.
2. Test operation method
(1) Switch on power, press "ON/OFF" button on the wireless remote control to start the
operation.
(2) Press MODE button, to select the COOL, HEAT, FAN to check whether the operation
is normal or not.
23
ENVIRONMENTAL INFORMATION
This unit contains fluorinated gases with greenhouse effect covered by the Kyoto Protocol.
Maintenance and disposal must be carried out by qualified persons only.
Refrigerant gas R410A, GWP = 1730
EXTRA REFRIGERANT CHARGE
Pursuant to Regulation EC 842/2006 on certain fluorinated greenhouse gases, in case of extra
refrigerant charge, it is compulsory to:
-
Fill in the label accompanying the unit inserting the factory quantity of refrigerant
charge (see the technical label), the extra refrigerant charge and the total charge.
Apply the label next to the technical label applied on the unit. For the split-type air
conditioner apply on the outdoor unit.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement