HP Managed PDU

HP Managed PDU

HP Managed Power Distribution Unit

User’s Guide

Abstract

This document is for the person who installs and maintains HP PDU products. HP assumes you are qualified in the installation of electrical equipment and trained in recognizing hazards in products with hazardous energy levels.

Part Number: 793528-001 EN

September 12, 2014

Edition: 1

Special Symbols

The following are examples of symbols used on equipment to alert you to important information:

RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of electric shock symbol.

CAUTION: REFER TO OPERATOR'S MANUAL - Refer to your operator's manual for additional information, such as important operating and maintenance instructions.

This symbol indicates that you should not discard waste electrical or electronic equipment (WEEE) in the trash. For proper disposal, contact your local recycling/reuse or hazardous waste center.

Hewlett-Packard is a registered trademark of Hewlett-Packard Development Company, L.P. HyperTerminal is a registered trademark of Hilgraeve. National Electrical Code and NEC are registered trademarks of National Fire

Protection Association, Inc. Microsoft, Windows, and Internet Explorer are registered trademarks of Microsoft

Corporation in the United States and other countries. Linux is a registered trademark of Linus Torvalds in the

United States, other countries, or both. Mozilla and Firefox are registered trademarks of Mozilla Foundation.

Torx is a registered trademark of Textron, Inc. Phillips is a registered trademark of Phillips Screw Company. All other trademarks are property of their respective companies.

© Copyright 2014 Hewlett-Packard Development Company, L.P.

The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

HP Managed PDU User’s Guide 793528-001 EN—Rev Edition 1 2

Table of Contents

1

2

3

4

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

HP MA PDU Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MA PDU Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Special Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Environmental Monitoring Probe Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

22U Shipping Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Ease of Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9

Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10

9

9

9

9

2

2

Power Control Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10

Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10

Configurability and Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10

1

1

SAFETY WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Installation Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13

Inspecting the Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14

Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14

Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

15

Special Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18

Environmental Monitoring Probe Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18

Shipping Retention Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18

IEC Outlet Grip Plug Retention Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19

Installing the MA PDU in a Rack Cabinet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19

Vertical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19

Grounding the MA PDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20

Network and Environmental Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21

Connecting to a Computer Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21

Connecting to a LAN Ethernet Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

22

Connecting Multiple MA PDUs in a Daisy Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

23

Connecting Optional Environmental Monitoring Probe Equipment. . . . . . . . . . . . . . . . . . . . . .

25

Connecting the Output Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

26

Operating the MA PDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

26

NETWORK COMMUNICATION CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

LCD — DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

27

LCD— Static IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

28

Serial connection — Static IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

29

Verify Web Operation After Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30

HP Managed PDU User’s Guide 793528-001 EN—Edition 1 i

Table of Contents

5

6

7

OPERATION OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Operation Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

313Ph Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

33

Pin Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

33

Environmental Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

33

Outlets and Circuit Breakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

33

Menu and Status Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

34

LCD Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

34

Main Menu Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

34

Status Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

34

Front Panel Ports, Status Indicators, and Operation Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

35

Common Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

36

Starting the MA PDU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

36

Shutting Down the MA PDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

37

Restarting the eNMC Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

37

LCD INTERFACE OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

LCD Display and Control Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

38

Operation Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

39

Screensaver Cycling Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

39

Startup Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

39

Password Protected Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

40

Main Menu Selections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

40

Active Alarms Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

42

Alarms History Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

42

Meter Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

43

PDU Submenu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

43

Sections Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

45

Outlets Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

45

Environment Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

46

Control Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

47

Settings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

47

USB Flash Mode Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

48

Display Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

51

Daisy Chain Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

52

IPv4 Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

54

Language Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

55

Factory Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

55

MA PDU Info Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

56

WEB INTERFACE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Navigate the Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

57

Languages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

59

Access the Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

59

Menu Selections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

60

Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

61

Logs & Notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

61

Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

62

Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

62

HP Managed PDU User’s Guide 793528-001 EN—Edition 1 ii

Table of Contents

Access Privileges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

62

SuperUser Administrator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

62

Local or Remote Administrator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

63

Local or Remote PDU-User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

64

Session Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

64

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

65

Review/Modify the PDU Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

65

Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

66

Review/Modify the PDU Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

66

Outlets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

67

Review/Modify the PDU Outlets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

67

Power Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

68

Define a Power Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

68

Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

69

Configure Environment Sensor Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

69

Active Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

70

Review Active Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

70

Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

71

Clear the Event Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

71

Download the Event Log as a CSV File From the Web Interface . . . . . . . . . . . . . . . . . . . . . . .

71

Download the Japanese-specific Event Log as a CSV File From the PDU to Excel . . . . . . . . .

71

Trap Notification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

72

Define the Trap Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

72

Syslog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

73

Retrieve/Modify Syslog Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

73

Access Accounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

74

Configure the SuperUser. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

74

Configure the E-mail Notification Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

74

Configure the LCD Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

75

Configure Local User Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

75

Configure Remote Group Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

76

System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

77

Set General System Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

77

Enable/Disable Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

78

Configure PDU Network Management Card Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

78

Perform Firmware Upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

79

Configure the PDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

79

Date & Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

80

Manual Configuration of the Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

80

Automatic Configuration of the Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

80

TCP/IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

80

Configure the Ethernet Link Speed and Duplex Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

81

Configure the IPv4 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

81

Configure the IPv6 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

82

Configure the DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

82

Configure the SMTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

83

HP Managed PDU User’s Guide 793528-001 EN—Edition 1 iii

Table of Contents

8

9

SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

83

Enable/Disable the SNMP Agent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

83

Define SNMPv1 Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

83

Define SNMPv3 User-based Security Model Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

84

Access PDU MIB Objects (Privileged Access Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

84

Energy Wise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

84

Enable Energy Wise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

84

Disable Energy Wise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

85

Start/Stop Energy Wise Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

85

Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

85

Enable/Disable SSL Encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

85

Enable/Disable the Telnet Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

86

Enable/Disable the SSH Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

86

Enable/Disable FTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

86

Set Authentication Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

87

Set LDAP Search Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

87

Authenticate LDAP Remote User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

88

Set LDAP Server Global Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

90

Modify LDAP Server Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

90

Add RADIUS Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

91

Edit Parameters for a RADIUS Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

91

SERIAL INTERFACE OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Supported Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

92

info command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

94

quit command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

96

get command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

97

set command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

99

pdu command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

XML Object Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

MAINTENANCE AND ALARMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

Preventive Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

Equipment Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

Replace the MA PDU eNMC Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

Replace an eNMC that is Not Working . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

Replace a Working eNMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

Restart the eNMC Module and Reset the MA PDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Upgrade Firmware with Hypertext Transfer Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Upgrade the Firmware with FTP Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

Upgrade the Firmware with the USB Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

Active Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

Define the Alarm or Event Condition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

Type Code 0 or 1 (OS or System) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132

Type Code 2 or 3 (PDU or User) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

HP Managed PDU User’s Guide 793528-001 EN—Edition 1 iv

Table of Contents

10

11

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137

Model List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137

Weights and Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137

Electrical Input and Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138

Electrical Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138

Overcurrent Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139

Environmental and Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139

Regulatory Model Numbers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140

SUPPORT AND OTHER RESOURCES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

Before You Contact HP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

HP Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

HP Product QuickSpecs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

Documentation Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

HP Managed PDU User’s Guide 793528-001 EN—Edition 1 v

Chapter 1 Introduction

Description

The HP MA (Managed) PDU (Power Distribution Unit) is an intelligent MA PDU that is designed to distribute power to multiple loads for data center equipment installed in a rack. The HP MA PDUs are 1Ph (single-phase) and 3Ph (three-phase) MA PDUs with monitoring at the input, branch, and individual outlet control and monitoring.

Each MA PDU provides power distribution to IT loads through multiple C19, C13, and NEMA 5-20R outlet types on 1PH and 3PH models. The number and location of outlets vary by model. The MA PDUs allow you to connect and manage these outlets from a single power connection. The MA PDUs can be managed from a local interface, a CLI (Command Line Interface) interface, or a Web interface.

HP MA PDUs are designed to be installed in HP 10000 series racks or Intelligent series racks, but can be used in other standard data center racks. The MA PDUs vary in form factor height and several mounting configurations are available, depending on the model.

Figure 1 shows an example of a MA PDU installed in a rack.

Figure 1. Example HP MA PDU Installed (Bottom Entry Method)

HP Managed PDU User’s Guide 793528-001 EN—Edition 1 1

Introduction

HP MA PDU Models

The MA PDUs are available in 22U and 42U form factor heights for standard racks. These models are designed for NA (North American), NA/JP (North American/Japanese), INTL (International), and WW (WorldWide) markets.

NOTE

The WW market includes both INTL and NA models.

The PDU models support 1Ph or 3Ph applications and provide between 8 and 24 outlets. All models feature an

LCD window, a set of communication port connectors, a reset button, and operation buttons. The MA PDUs have either attached or detachable input power cords. Circuit breakers are provided on most models.

NOTE

For details about individual model configurations, see “Specifications” on page 137.

MA PDU Models

Available models include: l

H8B48A: HP 2.8kVA 120V 30A NA/JP maPDU l

H8B49A: HP 3.6kVA 200-240V 16A WW maPDU l

H8B50A: HP 4.9kVA 208V 30A NA/JP maPDU l

H8B51A: HP 7.3kVA 200-240V 32A INTL maPDU l

H8B52A: HP 8.6kVA 208V 30A 3Ph NA/JP maPDU l

H8B53A: HP 8.6kVA 208V 30A 3Ph DV NA/JP maPDU l

H8B54A: HP 11kVA 400V 16A 3Ph INTL maPDU l

H8B55A: HP 14.4kVA 208V 50A 3Ph NA/JP maPDU l

H8B56A: HP 17.3kVA 208V 60A 3Ph NA/JP maPDU


Figure 2 illustrates the 1Ph H8B48A MA PDU model.

Introduction

Figure 2. 1Ph H8B48A Model





Ø

Introduction




Ø

Introduction




Introduction




Introduction






Introduction




Introduction


Special Equipment

Environmental Monitoring Probe Equipment

Optional environmental monitoring probe (EMP) equipment provides monitoring of external temperature, humidity, and the status of contact devices (sensors), providing greater power management control and flexible monitoring. This optional equipment can be connected to the MA PDU. The monitoring firmware collects and reports data from the sensors.

NOTE

EMP equipment is optional and must be purchased separately.

22U Shipping Brackets

The 22U HP MA PDUs are shipped with shipping retention brackets. The shipping retention bracket is used when a 22U MA PDU is installed into the rack and the rack is being shipped without removing the MA PDU.

Features

The MA PDUs provide outstanding performance and reliability, including the following unique benefits.

Ease of Use

l

Easy and flexible rack installation l

Easy-to-use interface to display input and output status l

Remote and local firmware updates


Introduction l

Top and bottom mounting in the rack l

Mounting holes on the back, left side, and right side to accommodate suitability for each customer site

Communication

l

Comprehensive power management and flexible configuration through a Web browser or a serial connection, SNMP (Simple Network Management Protocol), or a console emulator, such as HyperTerminal l

Compatibility with network management tools, facilitated by SNMP protocol

Power Control Management

l

Fully shrouded local branch circuit breakers on products rated over 16A (Europe)/20A (US) to protect connected equipment against overload and short circuits

Monitoring

l

Monitoring the MA PDU locally or remotely through a console or network l

Monitoring data for multiple daisy-chained MA PDUs from the same network connection l

Remote monitoring of connected environmental sensors l

Dual-color LCD for higher visibility on local alarms l

External connections to allow remote management by network and serial communications (RS-232 or RJ-45 connector) l

Firmware network stack supports both IPv4 and IPv6

Configurability and Security

l

Configurable alarm thresholds l

Configurable user-security and permission control l

Local and remote configuration functions available through onboard LCD display of menu selections, Web interface, or CLI interface


Chapter 2 Safety Warnings

IMPORTANT SAFETY INSTRUCTIONS — SAVE THESE INSTRUCTIONS

This manual contains important instructions that you should follow during installation and operation of the HP Managed PDU. Please read all instructions before operating the equipment and save this manual for future reference.

For safety, environmental, and regulatory information, see Safety and Compliance Information for

Server, Storage, Power, Networking, and Rack Products, available at the HP website

(http://www.hp.com/support/Safety-Compliance-EnterpriseProducts).

DANGER

This MA PDU contains LETHAL VOLTAGES. All repairs and service should be performed by

AUTHORIZED SERVICE PERSONNEL ONLY. There are NO USER SERVICEABLE PARTS inside the MA PDU.

The installation of options, routine maintenance, and service of this product must be performed by individuals who are knowledgeable about the procedures, precautions, and hazards associated with AC power products.

IT IS ESSENTIAL THAT THIS EQUIPMENT IS CONNECTED TO AN ELECTRICAL SUPPLY THAT HAS

PROTECTIVE GROUND CONDUCTOR.

WARNING

HIGH LEAKAGE CURRENT. It is essential that you make an earth connection before connecting the supply.

CAUTION

l

To reduce the risk of fire or electric shock, install this MA PDU in a temperature and humidity controlled, indoor environment, free of conductive contaminants. Do not operate near water or excessive humidity (90% maximum noncondensing).

l

Ambient temperature must not exceed 0°C to 50°C (32°F to 122°F) on all INTL and WW models.

l

Ambient temperature must not exceed 0°C to 60°C (32°F to 140°F) on all NA/JPN (except as noted previously).

l

Do not use a two-wire power cord in any product configuration.

l

Test AC outlets at your computer and monitor for proper polarity and grounding.

l

Use only with grounded outlets at both the computer and monitor. When using a backup UPS, power the computer, monitor, and appliance off the supply.

l

The installation power outlet used for the power supply to this equipment must be installed near the equipment and must be easily accessible. If the PDU does not provide an input branch circuit breaker, a socket-outlet or disconnection device must be installed near the PDU and must be easily accessible l

When installing this product, it is essential that the distribution circuit supplying the product is protected by a branch circuit protection device with a maximum rating to suit the product maximum rating.

l

TO ISOLATE THIS EQUIPMENT, DISCONNECT THE POWER SUPPLY PLUG.

l

This MA PDU is intended for providing power to equipment only. Secondary (satellite) power strips shall not be connected to the outlets.


Safety Warnings l

The internal components can become extremely hot during operation. Allow sufficient time for the PDU to cool before handling.

l

This equipment is intended for installation in Restricted Access Locations such as computer rooms, network closets, and equipment racks.

l

This product has been designed to conform to the latest safety requirements. In addition to compliance with standards for general use, it has been factory configured for use in rack mounting environments, aiding the installer to provide systems compliant with relevant standards.

CAUTION

This product contains a lithium battery on the internal eNMC module: l

The battery is not user-replaceable. There is a danger of explosion if the battery is not correctly replaced. The battery must be replaced with the same (or equivalent) type of battery.

l

The battery is not user-replaceable. However, ensure that used batteries are disposed of according to the instructions. For more information, contact your local recycling/reuse or hazardous waste center for proper disposal information.


Chapter 3 Installation

The 22U and 42U HP Managed PDUs are mounted vertically inside rack structures. Use the information in this chapter to prepare, install, and connect the MA PDU and optional accessories.

Installation Precautions

Before you install or connect the MA PDU in a rack cabinet, observe the following precautions: l

Only a competent service person should install, test, or configure the MA PDU and its optional accessories.

It is the installer’s responsibility to ensure that the selected product is installed to meet national and local safety regulations.

l

Read and understand all warnings and cautions listed in “Safety Warnings” on page 11.

l

Review the documentation that comes with your rack cabinet for safety and cabling information.

NOTE

Removing the rack cabinet doors and side panels might make installation easier. See the rack cabinet documentation for more information.

l

Verify that the room air temperature is below 50°C (122°F).

l

Take all necessary precautions to handle the weight of the devices.

l

Connect all power cords to properly wired and grounded electrical outlets.

l

Verify that the power outlet is near the equipment and is easily accessible so that the MA PDU can be disconnected quickly.

CAUTION

The installation power outlet used for the power supply to this equipment must be installed near the equipment and must be easily accessible. If the PDU does not provide an input branch circuit breaker, a socket-outlet or disconnection device must be installed near the PDU and must be easily accessible.

l

Do not overload the power outlet when you install multiple devices in the rack cabinet.

l

To reduce the risk of fire, connect only to a circuit provided with branch circuit overcurrent protection with an

A (ampere) rating in accordance with the NEC (National Electrical Code), ANSI/NFPA 70 or your local electrical code.

l

Verify that all equipment is unplugged from MA PDU outlets before performing any testing.

l

For units without circuit breakers (H8B49A and H8B54A), the output power cannot be turned on and off with a button or switch. These PDUs are always on when they are plugged in. These PDUs are always off when they are unplugged.

l

For units with circuit breakers, the circuit breaker controls whether there is output power:

- If the circuit breakers are on, there is output power, the LCD display is on, and the network communications module is operational.

- If the circuit breakers are off, there is no output power, but the LCD display is on, and the network communications module is operational.

- To turn off the MA PDU, unplug it.

NOTE

The illustrations in this document might differ slightly from your hardware.


Installation

Inspecting the Equipment

If any equipment has been damaged during shipment, keep the shipping cartons and packing materials for the carrier or place of purchase, and file a claim for shipping damage. If you discover damage after acceptance, file a claim for concealed damage.

To file a claim for shipping damage or concealed damage: 1) File with the carrier within 15 days of receipt of the equipment; 2) Send a copy of the damage claim within 15 days to your service representative.

Installation Overview

NOTE 1

Power cords for the devices that you connect to the MA PDU are not included.

NOTE 2

Depending on your choice of installation method, some parts may not be used.

Tools

The following tools may be needed to install the MA PDU in a rack cabinet (varies with round-, threaded-, or square-hole racks): l

Phillips cross-head screwdriver l

Flat-blade screwdriver l

8.7 mm (11/32”) wrench


Package Contents

Table 1 lists the parts that are included with the PDUs.

Table 1. Parts Included with HP PDU Models

Quantity

1

Description

User Documentation Download Information Sheet

NOTE

User documentation is accessed online and is available in English, Kazakh, Ukrainian, Russian,

French, Italian, Spanish, German, Japanese, and

Brazilian Portuguese languages. Download information links are provided on this sheet.

1

Safety/Regulatory Information Sheet

*733168-001 *

Installation

*703828-023*


Installation

Table 1. Parts Included with HP PDU Models (Continued)

Quantity

1

Description

Installation Pack for 42U Models:

(2) Key hole buttons, (3) M4-0.5P screws

SEE NOTE 1

(1) Serial cable used for RS-232 connection between the PDU and a PC

(1) RJ-45 Cable (60 cm - shielded) used for Ethernet or daisy-chain connection between the PDU and a PC SEE NOTE 2

(1) Y Splitter installed in the Daisy-chain port and used for daisy-chaining three or four PDUs together

(2) Cable ties


Installation

Table 1. Parts Included with HP PDU Models (Continued)

Quantity

1

Description

Installation Pack for 22U Models:

(2) Key hole buttons, (3) M4-0.5P screws

SEE NOTE 1

(1) Bracket, (3) self-tapping bracket screws

(1) Serial cable used for RS-232 connection between the PDU and a PC

(1) RJ-45 Cable (60 cm - shielded) used for Ethernet or daisy-chain connection between the PDU and a PC SEE NOTE 2

(1) Y Splitter installed in the Daisy-chain port and used for daisy-chaining three or four PDUs together

(2) Cable ties

NOTE 1

The keyhole mounting button and screws are packaged together in a small, clear shipping bag within a larger bag or box. These parts are shipped in the carton with the MA PDU.

NOTE 2

The Ethernet cable is intended for customers with small data centers, for maintenance, or for checks in a warehouse setting. Larger data center customers may choose to use their own network cable.

!

IMPORTANT

Model H8B49A has an IEC 60320 C20 power input receptacle for attaching a C19 to the country-specific power cord of your choice. These cables are ordered separately.


Installation

Special Equipment

Environmental Monitoring Probe Equipment

EMP equipment with sensors can be connected to the MA PDU as an accessory that collects temperature and humidity data, as well as two dry contacts. The equipment is user-provided and should be installed using the manufacturer’s instruction manual.

!

IMPORTANT

Follow all installation and operation safety information provided in the manufacturer’s instruction manual for the EMP equipment.

Shipping Retention Brackets

Shipping retention brackets can be installed to provide additional stability for the models when the MA PDU is installed in a rack and the rack is being shipped. The bracket is used only for 22U models. The 42U models can be secured for shipping within a rack using a cable tie on the power cable. Mounting screws (self-tapping screws) are supplied with the bracket in the shipping carton. When the MA PDU is unpacked, retain the brackets and mounting hardware for future use.

Secure the bracket to the rack above the MA PDU to help prevent it from shifting during transport as follows

(see Figure 11):

1.

Align the bracket with the top of the MA PDU model and hold it in place above the PDU.

2.

Use the two bracket mounting screws to attach the bracket to the rack post.

22U PDU

Figure 11. Installing a Bracket for Transporting a 22U PDU in the Rack


Installation

IEC Outlet Grip Plug Retention Mechanism

The HP Managed PDUs have a mechanism integrated with the outlets to retain a plug inside its outlet. This system is a lever-actuated grip that prevents the plug from accidentally being bumped out or vibrating out of the outlet. It is not a locking device so the plug can still be removed in an emergency.

Figure 12. Plug Retention Mechanism

NOTE

In the event of an emergency, only unplug the power cord when the grip plug retention mechanism is in the “+” position (plug retained). To remove the plug, gently rotate the lever to the “O” (plug freed) position and remove the plug.

NOTE

If you choose, you can further secure the plug with a cable tie.

Installing the MA PDU in a Rack Cabinet

HP MA PDUs are designed to be installed in HP 10000 series racks and Intelligent series racks, but can be installed in other data center racks.

NOTE

All vertically installed MA PDU models use keyhole mounting buttons for installation in a rack cabinet.

Vertical Installation

The following vertical configurations are available: l

A single 42U MA PDU on one side or both sides of the rack l

Two 22U or 42U MA PDUs side-by-side on one side or both sides of the rack l

A single or two 22U MA PDUs on one side or both sides of the rack

NOTE

Two 22U MA PDU models fit vertically in a 42U HP rack with one mounted on top of the other.

A top and button mounting button should be installed on each PDU to install it vertically. The mounting buttons are then inserted into the corresponding keyhole slot.


Installation

Installing PDUs

To install the PDU vertically with mounting buttons directly attached to the PDU:

1.

Locate the two keyhole mounting buttons and installation screws (supplied).

2.

Decide how to orient the MA PDU in the rack.

NOTE

The MA PDU orientation you choose will determine whether you install the mounting buttons on the back, left side, or right side of the MA PDU.

3.

Using the supplied screws and a Phillips screwdriver, secure the top and bottom mounting buttons on the back, left side, or right side of the MA PDU. The screw should be torqued to six inch-pounds.

NOTE

Make sure the screw is completely seated in the mounting button so that it is not protruding from the recessed button mounting hole.

4.

Before attempting to mount the MA PDU or MA PDUs, locate the keyhole slots on the rack post that correspond with the position of the top and bottom mounting buttons.

CAUTION

Use great care in handling the PDU in the following steps. Avoid contact between the PDU and the rack because there is a risk of damage to the PDU or the rack.

5.

Install the PDU or PDUs in the rack:

- Carefully move the PDU into position against the rail.

- Insert the top and bottom mounting buttons into the appropriate keyhole slots.

- Push down to secure the PDU in position.

- Repeat with any additional PDUs.

6.

Continue to “Grounding the MA PDU”if you are installing a ground screw and grounding cable.

Otherwise, go to “Network and Environmental Ports” on page 21.

Grounding the MA PDU

NOTE

Grounding the MA PDU is optional but recommended.

Conductors can be connected to the ground screw for functional grounding or bonding of ungrounded metal parts within the rack. The grounding screw is sized to safely conduct the fault current of the single largest output breaker.

Neither the earth bonding screw nor the surface of the chassis around the screw is painted. This ensures that the screw and washers make contact with bare metal, not a painted surface.

The ground symbol is impressed in the chassis above the earth bonding screw.

To ground the MA PDU, connect a grounding cable (not supplied) from earth to the grounding screw shown in

Figure 13.


Installation

Figure 13. Grounding the MA PDU

Network and Environmental Ports

The MA PDUs provide four types of ports for network connectivity and environmental monitoring.

l

To connect the MA PDU to a serial port on a computer, go to the next section, “Connecting to a Computer

Serial Port”.

l

To connect the MA PDU to an Ethernet port and the LAN (Local Area Network), go to “Connecting to a LAN

Ethernet Port” on page 22.

l

To daisy-chain multiple MA PDUs, go to “Connecting Multiple MA PDUs in a Daisy Chain” on page 23.

l

To connect the MA PDU to EMP equipment, go to “Connecting Optional Environmental Monitoring Probe

Equipment” on page 25.

Connecting to a Computer Serial Port

Connecting the MA PDU to a computer allows communication through a serial connection.

To connect the MA PDU to a computer:

1.

Verify that the computer has a communication program such as HyperTerminal.

2.

Locate the DB9-to-RJ-45 cable (provided).

3.

Connect the RJ-45 end of the cable to the RS-232 connector on the front panel of your MA PDU model

(see Figure 14). Connect the DB9 end of the cable to the serial connector on the computer.


Installation

22U and 42U MA Model Front Panel

Figure 14. Connecting to a Computer Serial Port

NOTE

If your computer does not have a DB9 serial connector, but does have a

USB connector, obtain a DB9-to-USB converter cable. Follow the manufacturer’s instructions to install the converter cable device drivers and to connect the converter cable to your computer.

4.

Open the communication program on the computer and select the serial port connection (such as COM1).

5.

Verify that the port settings are configured as follows:

- Baud rate (bits per second) = 9600

- Data bits = 8

- Stop bits = 1

- Parity = None

- Flow control = None

6.

Verify that the MA PDU is turned on.

7.

Press Enter ( ) to display the opening configuration prompt and type admin (the default login).

8.

Press Enter ( ) and type admin (the default access password).

Connecting to a LAN Ethernet Port

Connecting the MA PDU to a LAN provides communication through an Internet or Intranet connection. You can monitor the MA PDU from any computer connected to the same network.

To connect the MA PDU to a LAN:

1.

Locate the Ethernet cable (provided).

NOTE

A short Ethernet cable is supplied in the MA PDU shipping carton. This cable is useful in a small data center for maintenance or for checks in a warehouse setting.

Larger data center customers may choose to use their own network cable.

2.

Connect one end of the cable to the Ethernet connector on the MA PDU (see Figure 15). Connect the

other end of the cable to the Ethernet connector on the router (or other LAN device.


Installation


Figure 15. Connecting the MA PDU to a LAN

Connecting Multiple MA PDUs in a Daisy Chain

Multiple MA PDUs can be chained together using an Ethernet cable between the Daisy Chain ports located on the front panel. This allows access to the MA PDU data of multiple MA PDUs from the same network connection. One MA PDU is defined as the Host. This is the MA PDU with a connection to the network. The other MA PDU (or MA PDUs) are defined as Devices and they are connected to the host.

Configure the MA PDUs using the LCD or the CLI interfaces. Monitor the MA PDUs using the CLI interface or the Web interface.

To connect MA PDUs in a Daisy Chain communication configuration:

1.

Locate an Ethernet cable or cables (one cable is supplied).

2.

How many MA PDUs are you daisy-chaining?

l

If three or four, go to Step 3.

l

If two, go to Step 4.

3.

Insert the Y splitter in the Daisy Chain connector of the middle MA PDU or MA PDUs as shown in

Figure 16.

4.

Connect one end of the cable to the Daisy Chain connector on one MA PDU. Connect the other end of the

cable to the Daisy Chain connector on the other MA PDU or MA PDUs as shown in Figure 16.

NOTE

Only one MA PDU in a daisy-chained group can have a network connection through the Ethernet port. This MA PDU is the Host and any connected MA PDUs are

Devices.


Installation

Network Connection

(Ethernet Port)

Host [0]

Device [1] Device [2]

Device [3]

4 Daisy Chain Ports Connected

(Two Splitters Needed)

Network Connection

(Ethernet Port)

Host [0]

Device [1]

Device [2]


(One Splitter Needed)

Network Connection

(Ethernet Port)

Host [0]

Device [1]


(No Splitter Needed)

Figure 16. Locating the Daisy Chain Connector

5.

Configure the MA PDUs with either the LCD interface or the CLI interface.

l

To configure the MA PDUs using the LCD interface, go to “Daisy Chain Submenu” on page 52.

l

To configure the MA PDUs using the CLI interface, go to “Serial Interface Operation” on page 92.

6.

Monitor the MA PDUs with the CLI interface or the Web interface.

l

To monitor the MA PDUs using the Web interface, go to “Web Interface Operation” on page 57.

l

To monitor the MA PDUs using the CLI interface, go to “Serial Interface Operation” on page 92.


Installation

Connecting Optional Environmental Monitoring Probe Equipment

You can purchase optional EMP equipment to monitor temperature and humidity around the MA PDU and to monitor the status of sensors.

You can install an optional EMP now or after completing the MA PDU installation and startup. Optional EMP equipment can be installed without turning off power to the MA PDU or the devices connected to it.

!

IMPORTANT

Follow all installation and operation safety information provided in the manufacturer’s instruction manual for the EMP equipment.

To install an optional EMP:

1.

Locate the EMP and the RJ-45-to-RJ-45 Ethernet cable.

2.

Refer to the manufacturer’s installation manual for instructions to connect the external contact inputs to the optional EMP for the external contact devices you plan to monitor.

3.

Locate the Ethernet cable dedicated to the EMP. Connect one end of the cable to the RJ-45 connector on

the EMP, then connect the other end of the cable to the RJ-45 connector on the MA PDU (see Figure 17).


Figure 17. Connecting the EMP to the RJ-45 Serial Port Connector

NOTE

The maximum cable length is 2.99m (9.8 ft).

4.

Use the mounting method appropriate to your installation to mount the EMP in a convenient location anywhere on the rack.

5.

Use cable ties to secure the Ethernet cable out of the way as needed. On startup, the MA PDU automatically recognizes the EMP.


Installation

Connecting the Output Devices

The MA PDU outlets are available for connecting and monitoring devices such as workstations, servers, and printers. Connect a device you want to monitor to a power outlet on the MA PDU with the power cord that comes with the device.

NOTE

You may find it useful to document the connections you make.

To connect your devices:

1.

Verify that each circuit breaker is in the On position.

2.

For MA PDUs with detachable power cords. If the power cord is not connected, connect the power

cord to the MA PDU. Otherwise, go to Step 3.

3.

Route the MA PDU power cord toward a dedicated power source. Use cable ties to secure the power cord as needed. If the power cord must exit the rack cabinet to connect to a power source, use the openings in the rack cabinet.

NOTE 1

Plug the MA PDU into an appropriately rated outlet for its type.

NOTE 2

Do not replace or rewire the power cord.

4.

Connect the power cord to a properly wired and grounded dedicated power source. The MA PDU turns on and displays the HP startup screen while starting. After five seconds, the sequence of screensaver screens for this MA PDU model begin cycling.

5.

Verify that no alarms display on the LCD. To resolve alarms, see “Maintenance and Alarms” on page 121.

6.

Make sure the grip plug retention lever is on the “O” position before inserting the plug.

7.

Plug in your output devices to the outlet outlets on the MA PDU. Verify that each device is receiving power before connecting the next device

NOTE

To avoid large surge currents, connect the protected equipment to the outlets individually rather than as a group. You may want to include a delay when setting up groups of outlets to start at the same time to avoid a large in-rush current.

8.

Gently rotate the grip plug retention lever to the “+” position. You should hear a “click” sound as the mechanism engages.

NOTE

Only unplug the power cord when the grip plug retention mechanism is in the “+” position in an emergency. To remove the plug, gently rotate the lever to the “O” position and remove the plug.

Operating the MA PDU

See “Operation Overview” on page 31 for instructions to operate the MA PDU, including starting and shutting

down the equipment.


Chapter 4 Network Communication Configuration

The HP Managed PDU automatically collects the network communication configuration settings (IP parameters) from the server by default. When the MA PDU is not connected to the network, it continuously attempts to connect. If DHCP is enabled on your network, the MA PDU automatically collects the network communication configuration settings.

In order to establish a network session, note the network configuration from the LCD. Users/admin can review and change the network information using CLI, Telnet, and GUI once connected.

NOTE

In order to use Telnet, you must have a network connection already established.

The MA PDU defaults to using DHCP (Dynamic Host Configuration Protocol) when delivered. If you are unable to connect to the MA PDU through the network connection with this default address, change the IP address using the LCD or through the CLI using a terminal emulation program.

The network connection automatically receives an IP address through the DHCP if available on the network. If

DHCP is enabled but a DHCP server is not available, the eNMC module will use the last-used IP address setting.

Alternately, it is possible to set a static IP address by using either the LCD menu or a serial connection CLI

(command line interface).ga

The default settings are: l

DHCP: Enabled l

IP Address: 192.168.123.123 l

Subnet Mask: 255.255.255.0 l

Gateway: 192.168.123.1 l

Username: admin l

Password: admin

NOTE

If you use the default IP address and are able to make a direct connection, you could use Telnet to change the settings to some other fixed values.

LCD — DHCP

1.

The PDU defaults to DHCP enabled when delivered.

2.

Connect to a network that has a DHCP server and wait 20 seconds before the eNMC module reboots with the new IP address.

3.

Obtain the IP address from the LCD home screen (see Figure 18).

hp

MM/DD/YYYY

HH:MM:SS

IP Address

Part Number

Figure 18. LCD Home Screen


Network Communication Configuration

LCD— Static IP address

1.

Disable DHCP (see Figure 19).

Active Alarms

Alarms History

Meters

Control

Settings

PDU Info

Enter

ESC

Settings

Display

Daisy Chain

IPv4

Language

Factory

ESC

Enter

IPv4 Settings

DHCP

IP address

Subnet Mask

Gateway

ESC

Figure 19. Disable DHCP

2.

Set the static IP address (see Figure 20). Wait 10 seconds.

Enter

ESC

DHCP

Disable

Enable

Disable

Enter

Active Alarms

Alarms History

Meters

Control

Settings

PDU Info

Enter

ESC

Settings

Display

Daisy Chain

IPv4

Language

Factory

ESC

IPv4 Settings

DHCP

Enter

Subnet Mask

Gateway

ESC

Enter

ESC

192

IP address

168

123 123

OK

Enter

Figure 20. Set the Static IP Address

3.

After 10 seconds, locate the Reset opening (labeled R) on the MA PDU (see Figure 21). Insert an

electrically non-conductive probe, press the recessed button, and retract the probe. This restarts the

eNMC module and applies the new settings (see Figure 21).

22U and 42U Model Front Panel

Figure 21. Reset Button



Serial connection — Static IP address

Use the RJ45-to-DB9 serial cable that is provided to connect the computer to the PDU. If your computer does not have a DB9 (RS-232) connector, a USB-to-RS-232 adapter can be purchased separately. Access the CLI using a terminal emulation program such as HyperTerminal, PuTTY, or TeraTerm.

To set up the serial port using your selected terminal emulation program, use the following settings: l

Bits per second: 9600 l

Data bits: 8 l

Parity: None l

Stop bits: 1 l

Flow Control: None

After establishing a serial connection, perform the following steps:

1.

In the terminal emulator session window, enter the default user name (admin) at the login prompt. For example:

Enter Login: admin

Enter Password:

2.

Type admin (default) at the password prompt. Press Enter.The CLI uses a “get” command to return the value of a setting and a “set” command to change the value of a setting. For example:

PDU#0>set System.Network.DHCP 0

PDU#0>get System.Network.DHCP

0

3.

Type set System.Network.DHCP 0 and press Enter to modify the value (0 = disabled and 1= enabled). For example:

PDU#0>set System.Network.DHCP 0

0

4.

Set the IP address to a value provided by your system administrator.

PDU#0>set System.Network.IPAddress xxx.xxx.xxx.xxx

xxx.xxx.xxx.xxx

5.

If necessary, set the network Subnet Mask to the value required by your system administrator.

PDU#0>set System.Network.IPMask 255.255.yyy.yyy

255.255.yyy.yyy

6.

Set the network Gateway to the value required by your system administrator.

PDU#0>set System.Network.IPGateway zzz.zzz.zzz.zzz

zzz.zzz.zzz.zzz

7.

After 10 seconds, locate the Reset opening (labeled R). Insert an electrically non-conductive probe, press the recessed button, and retract the probe.

NOTE

You can also connect up to four MA PDUs together using the Daisy Chain port and

RJ-45 splitters. This enables multiple MA PDUs to communicate over one Ethernet port.



NOTE

If you choose not to use the procedure to configure the communications module without the DHCP server installed, you can connect to the MA PDU using the default address: http://192.168.123.123

Verify Web Operation After Configuration

To verify the communications module is operational and that you can access the Web interface:

1.

Open a Web browser.

2.

Enter the IPv4 or IPv6 address in the address bar in the following format:

http://<IPv4 address> or http://<IPv6 address>

3.

When the user authentication pop-up dialog displays, type admin in the User name field and admin in the

Password field.

4.

The home page opens with the MA PDU Overview page.


Chapter 5 Operation Overview

This chapter provides an overview of operation for the HP Managed PDUs.

Operation Features

Figure 22 shows isolated views of the display and connectivity areas.

3

4

5

4

1

2


SERIAL PORT USB PORT

RESET BUTTON

STATUS LED

SCROLL

LCD WINDOW

ESCAPE

ETHERNET PORT DAISY CHAIN PORT SCROLL ENTER

6

Figure 22. MA PDU Display and Connectivity


Operation Overview

Table 2 describes the operation features shown in Figure 22.

Table 2. PDU Operation Features

1

Reference

Number Feature

2

3

4

5

6

Description

LCD Window LCD Window: Displays information about load status, events, measurements, identification, and settings.

The LCD also provides some basic configuration. For more information, see “Menu and Status Display” on page 34.

Navigation buttons: Navigate through the display. For more information, see “Front Panel Ports, Status

Indicators, and Operation Buttons” on page 35.

Connectivity and Monitoring ports Serial Service and Communication Port: Connects to the serial (COM) connector on a computer with a

DB9-to-RJ-45 cable, allowing the computer to act as a configuration console. As an alternative, the connection can be used to connect an optional EMP in order to collect temperature and humidity data.

Ethernet Port Connector: Connects to a LAN, allowing configuration through a 10/100 autosensing network connection.

Daisy Chain Port Connector: Used to daisy chain multiple MA PDUs together.

USB Port: Used for Firmware upgrade.

Circuit breakers

Power outlets

Outlet indicator lights

Input power cord

Reset Button: Restarts the MA PDU eNMC module. Resetting the MA PDU does not affect the loads. Insert and retract an electrically non-conductive probe in the reset opening to perform an eNMC module restart.

Activate if the load current rating of a power outlet exceeds 16A (Europe) / 20A (US). Power to the outlet turns off automatically. To reset the circuit breaker, turn the breaker from off to on.

NOTE

The On/Off positions are indicated on the circuit breakers.

NOTE

To manually disconnect power to a device that is connected to the MA PDU, disconnect the device’s power cord from the MA PDU power outlet.

Allows you to connect one device to each outlet. The outlets are grouped by phase. Group configurations

cannot be changed. For more information, see “Outlets and Circuit Breakers” on page 33.

Provides a bi-color LED to indicate the status for each output receptacle: l

Solid red: Outlet off l

Flashing red: Outlet on, but breaker off l

Solid green: Outlet on l

Flashing green: Outlet on, outlet warning or critical overload l

Alternate flashing green and red: Outlet On, Breaker warning or critical overload

Allows you to connect to the power source. Input power cords are permanent for most models. Only the

H8B48A model has detachable input power cords.


Operation Overview

3Ph Configurations

The type of MA PDU input connector plug varies to accommodate different amperage ratings for 3Ph models.

The IEC 60309 connector plugs are configured as delta or wye topologies as follows: l

The delta configuration uses a four-wire input connector plug with three phase wires, a protective earth

(ground) wire, and no neutral wire. This is commonly expressed as 3W+PE (delta).

l

The wye configuration uses a five-wire input connector plug with three phase wires, a protective earth

(ground) wire, and a neutral wire. This is commonly expressed as 3W+N+PE (wye).

Pin Positions

The pin arrays are different for four-wire (delta) and five-wire (wye) 3Ph configurations. See Figure 23 for

example delta and wye pin positions.

4-Pin Plug (delta)

3W + PE

5-Pin Plug (wye)

3W + N + PE

L1

L1

L2

L2

G

G

L3

L3

Alignment Tab

Figure 23. Example 3Ph Pin Positions

N

Environmental Protection

The input connector plugs have Ingress Protection (IP) ratings that specify the degree of environmental protection for electrical equipment. The IEC 60309 input connector plugs are either splash resistant (S) or waterproof (W).

l

Splash resistant plugs are IP-rated at IP 44, which means the plug is protected against solid objects less than 1.0 mm in diameter.

l

Waterproof plugs are IP-rated at IP 67, which means the plugs are watertight, splashproof, and dust tight.

Table 3 shows examples and descriptions of delta and wye configuration codes.

Table 3. Example 3Ph Topologies

Code

460P9W

532P6S

Pin Positions

4-pin Plug (delta) - 4

5-pin Plug (wye) - 5

4

5

Maximum

Amperage

(A) Rating

60

32

Plug (P) outlet/Socket (R) or

Connector (C)

P

P

Clock Position

(6 or 9)

9

6

Waterproof (W) or

Splash Resistant (S)

W

S

Outlets and Circuit Breakers

Each MA PDU model has a specific configuration of outlets. The outlets are grouped in sets called outlet groups. Outlet groups are preset groups of individual outlets that you can identify and monitor through the different interfaces that are available with the MA PDU.


Operation Overview

The outlets are labeled, and if the model has circuit breakers, the circuit breakers that are associated with the outlets have corresponding labels.

Menu and Status Display

The LCD provides information in English about the MA PDU and connected devices using white text on a blue background. The LCD window flashes red when any alarm is active. Basic configuration of some settings is available through the LCD. Full configuration of all settings is available through the remote interfaces.

The LCD display orientation can be changed using an LCD or CLI setting. The display can be rotated 90°, 180°,

or –90° (270°). See “Display Submenu” on page 51 or see Example 2 in “set command” on page 99 for more

information.

LCD Window

The LCD has three modes: l

Screensaver mode (startup screen)

Screensaver mode cycles through a set sequence of screens that display current PDU values. Current values are refreshed every five seconds. The user cannot select a custom sequence of screens.

l

EcoMode (energy saving mode)

This mode is activated automatically when no button is pressed for 15 minutes and no alarm is active. The backlight is turned off to conserves energy.The screen darkens.

l

Settings mode (LCD main menu)

The settings that display under each high level (main) menu depend on your MA PDU model.

Main Menu Display

The menu items are highlighted when they are selected. The resulting screens can include data displays, value

setting options, or submenus. Figure 24 illustrates the highlighted Active Alarms LCD menu item selection.

Alarms History

Meter

Control

Settings

PDU Info

Figure 24. Menu Item Selection

Status Display

When the screensaver is activated, it displays a set of up-to-date values. However, this set of values is not user-configurable.To selectively view values, navigate through the LCD interface using the buttons on the front panel.

For example, selecting PDU from the Meter submenu and then selecting Total Input from the PDU Meter

submenu displays total input values for the PDU. Figure 25 is an example of the display for a 1Ph PDU.


Operation Overview

Main Menu

Active Alarms

ACTIVE ALARMS

EVENT LOG

OUTLET READINGS

SETTINGS

Enter

ESC

Meter

PDU

Sections

Environment

Enter

ESC

PDU Meter

Down

Total Input

50

.

23 Hz

Down

Total Input

Active Power

100 W

ESC

Total Input

Peak Power of xxxx W since

07/01/2011

17:32:23

Total Input

Down

Energy

16.238 kWh since

07/01/2011

17:32:23

Down

Total Input

Power Factor

0.912

Down

Down

Total Input

Apparent Power

120 VA

Reactive Power

20 VAR

Figure 25. Example of Selected Value Display

Front Panel Ports, Status Indicators, and Operation Buttons

The MA PDU front panel includes communication and environmental monitoring ports, LED status indicators, and operation buttons. There are three different front panel versions. Although the button and port position

varies, you can recognize the same button and port design from model to model (see Figure 26).

1

2 3

4

5

6

15

14 13 12 11 10 9

Figure 26. Front Panel Ports and Buttons (22U and 42U Front Panel)

8

Table 4 describes the ports and buttons identified in Figure 26.

4

5

6

Table 4. Communication and Environmental Monitoring Ports

Reference Number

1

2

3

Description

Service or Serial Port (Settings/Sensor)

Yellow Serial Service Port LED: RS-232 Operation and Activity Status

OFF: Normal operation

FLASHING: Communicating with EMP (if installed)

Green Serial Service Port LED: MA PDU Communication Status

OFF: PDU start-up in progress

FLASHING: Normal operation (network communication module operational)

USB Port: Used for Firmware upgrade

Backward (Down) Scroll Button

Escape (ESC) Button

HP Managed PDU User’s Guide 793528-001 EN—Edition 1

7

35

Operation Overview

Table 4. Communication and Environmental Monitoring Ports

8

9

Reference Number

7

10

11

12

13

14

15

Description

Enter Key

Forward (Up) Scroll Button

Green Daisy Chain Port LED: Role Assignment in Communication Protocol

ON: Device

FLASHING: Host

Daisy Chain Port Yellow LED: Transmission Activity Status

FLASHING: PDU is transmitting data

Daisy Chain Port (Communication Status of Chained PDU)

Yellow Ethernet Port LED: Connection and Transmission Activity Status

OFF: PDU not connected to the network

ON: PDU connected to the network, but no activity

FLASHING: Port is sending or receiving (transmission active)

Green Ethernet Port LED: Operation Transfer Rate Status

OFF: Port operating at 10 Mbits/s

ON: Port operating at 100 Mbits/s

Ethernet 10/100 Base-T Port

Reset Button

Common Operations

Starting the MA PDU

For units without circuit breakers, the MA PDU output power cannot be turned on and off with a button or switch. These MA PDUs are always on when they are plugged in. These MA PDUs are always off when they are unplugged.

For units with circuit breakers, the circuit breaker controls whether there is output power: l

If the circuit breakers are on, there is output power, the LCD display is on, and the eNMC is operational. l

If the circuit breakers are off, there is no output power, but the LCD display is on, and the eNMC is operational.

l

To turn off the MA PDU completely, unplug it.

To start up the MA PDU:

NOTE 1

Plug the MA PDU into an appropriately rated outlet for its type.

NOTE 2

Do not replace or rewire the power cord.

1.

For MA PDUs with detachable power cords. If the power cord is not connected, connect the power

cord to the MA PDU. Then, connect the power cord to a power source. Otherwise, go to Step 2.

2.

Does your MA PDU have a circuit breaker?

- For MA PDUs with circuit breakers. Verify all circuit breakers are in the On position.

NOTE


- For MA PDUs without circuit breakers. Plug in the power cord.


Operation Overview

Shutting Down the MA PDU

!

IMPORTANT

On models rated over 16A (Europe) / 20A (US), fully shrouded branch circuit breakers prevent accidental operation. To power cycle the HP MA PDU, unplug the power cord from the power source and then plug in the power cord.

To shut down the MA PDU:

1.

Shut down the connected devices according to the manufacturer’s recommended shutdown sequence.

2.

Does your MA PDU have a circuit breaker?

- For MA PDUs with circuit breakers. Turn each circuit breaker to the Off position.

NOTE 1


NOTE 2

To remove power from the MA PDU completely, disconnect the MA PDU power cord from the power source.

- For MA PDUs without circuit breakers. Unplug the power cord.

Restarting the eNMC Module

You can restart the eNMC module using either a hardware or software method.

A software restart is triggered from the Serial interface or Web interface upon user action. This method is typically the better choice because all current settings in the eNMC module file system are saved before restarting.

For a hardware restart, locate the Reset button (labeled R) on the MA PDU (see Figure 27). Insert an electrically

non-conductive probe, press the recessed button, and retract the probe. This method is not necessarily the best choice because the eNMC module does not force the system to save the parameters in the file system before restarting.

!

IMPORTANT

Restarting the eNMC module will not affect the output power or the connected equipment.

22U and 42U Model Front Panel

Figure 27. Reset Button


Chapter 6 LCD Interface Operation

This chapter contains operation information for the HP Managed PDUs, including: l

LCD display and control button functions l

Menu selections

NOTE

The LCD language is configurable. See language settings in“Language Submenu” on page 55.

LCD Display and Control Buttons

The MA PDU has a four-button, graphical LCD display (see Figure 28). Use the control buttons to change the

screen display, retrieve specific performance data, or change configuration values. The display view can also change automatically. For example, the display changes to show active alarms as they occur, or particular displays update due to a change in operating state.

A backlight is used to light up the display with white and blue: l

The backlight turns off automatically when no button has been pressed for 15 minutes and there is no active alarm. l

Any active alarm will cause the backlight to turn on automatically.

l

A red blinking background indicates that an alarm is active.

Figure 28. LCD Display

Table 5 summarizes how to use the control buttons.

Table 5. Control Buttons

Button When on the Main Menu

Returns to the Start-up screen.

When in Screensaver mode

Returns to the previous display screen before entering the screensaver mode.

Opens the selected menu.

NOTE: When menu items are highlighted, they are selected.

Scrolls up or down through the list of menu items.



When in Menu mode

Returns to the previous display screen.

Signals that you want to set the values as displayed on the screen.

NOTE: On information screens, this button has no action.

Scrolls up or down to the next screen or value.


LCD Interface Operation

Operation Mode

Screensaver Cycling Sequence

The screensaver displays automatically after 30 seconds of inactivity from the start-up screen, a menu, or a

submenu. Values are reset every five seconds.The screensaver displays data in a preset 1Ph cycle (Figure 29) or 3Ph cycle (Figure 30). These cycles are not user-configurable.

5 s

hp

IP Address

Part Number

Total Input

14.8

Amp

5 s

Figure 29. 1Ph Screensaver Cycle

5 s

hp

IP Address

Part Number

5 s

Phase C

1.47

Amp

Phase A

8.61

Amp

5 s

Phase B

3.26

Amp

Figure 30. 3Ph Delta-configured Screensaver Cycle

5 s

Startup Screen

When the MA PDU powers up, the Startup screen displays (see Figure 31). Press ENTER to go to the Main

Menu.

hp

MM/DD/YYYY

HH:MM:SS

IP Address

Part Number

Figure 31. Startup Screen



Password Protected Menus

Both Control and the Settings menus can be password-protected. This locks out the menus to any user who does not know the password.

!

IMPORTANT

Password configuration can only be done through the Web interface and the CLI menu.

On the Main Menu, scroll up or down to highlight Control. Press ENTER to display the Enter Password screen.

Scroll up or down in the number selection boxes to create a four-number password code. When you finish your entry, click OK. Press ENTER to return to the previous menu. A lock icon displays on the menu option you password protected.

Figure 32 illustrates the sequence to enter a password for a locked menu.

Enter Password

Active Alarms

Alarms History

Meter

Enter

Settings

PDU Info

:

Figure 32. Password Protected Screens

5

3

OK

2

4

Enter

Active Alarms

Alarms History

Meter

Control

:

Settings

PDU Info

:

Main Menu Selections

The MA PDU menu selection hierarchy provides useful performance information, alarms, MA PDU

identification, and configuration settings (see Figure 33). The available menu items are illustrated in a menu

hierarchy in Figure 34.

l

Use the scroll buttons to select a menu item from the Main Menu.

l

Selected menu items are highlighted and display as blue text on a white bar.

l l

Press ENTER to go the selected menu item.

Press ESC from the Main Menu to return to the Startup Screen.

Main Menu

Alarms History

Meter

Control

Settings

PDU Info

Figure 33. Main Menu Selections



HP

ACTIVE

ALARMS

ALARMS

HISTORY

METER CONTROL SETTINGS PDU INFO

Alarm 1 to N Alarm 1 to N

PDU

Total Input

(1)

Frequency

SECTIONS

Voltage

Current

Active Power

Apparent

Power

Reactive

Power

Percent

Load

Crest Factor

OUTLETS

Current

Active Power

Apparent

Power

Reactive

Power

Crest Factor

ENVIRON-

MENT

Temperature

Humidity

NOTE 2

Power Factor

Factor

Power Factor

Percent

Load

Energy

(kWh)

Energy

(kWh)

Outlets ON/

OFF

DISPLAY

Contrast

Orientation

Peak Current

DAISY

CHAIN

Settings

Discovery

NOTE 3

IPv4 FACTORY

DHCP Mode LANGUAGE

USB Flash

Mode

Input Phases

Current

Voltage

Frequency

Active Power

Apparent

Power

Reactive

Power

Peak Factor

Percent

Load

Power Factor

Active Power

Apparent

Power

Reactive

Power

Power Factor

Energy

(kWh)

IPv4 address

Subnet Mask address

Gateway address

Save Config.

Load Config.

Upgrade F/W

Save eNMC

File

Load eNMC

File

Exit

NOTE 4

Energy

(kWh)

NOTE 1

NOTE 1

These submenus are only available for 3Ph input MA PDUs.

NOTE 2

This menu and submenu are only available if an EMP is connected.

NOTE 3

This submenu is available, but can only be used for configuration Settings and Discovery when two or more MA PDUs are daisy-chained.

NOTE 4

This submenu is only available if a USB drive is detected.

Model

Part number

Serial

Number

Firmware

Version

IPv4 addr

IPv6 addr

MAC

Address

Figure 34. PDU Menu Hierarchy



Different sets of menus display depending on the type of topology you are managing or monitoring.

Table 6 shows LCD menus that are valid for MA PDU topologies.

Table 6. Menus Available for PDU Topologies

Meter

see NOTE 1

MA PDU

Models

Managed (MA)

Active

Alarms

•

Alarm

History

•

Input

Phase see NOTE 2

Total

Input (1)

•

Total

Input (2)

—

Sections

•

Outlets

•

Control

•

Settings

•

NOTE 1

The Meter > Environment menu is only available if an Environmental Monitoring Probe (EMP) is attached.

PDU

Info

•

NOTE 2

The Input Phase menu is available if the MA PDU has multiple phases.

Active Alarms Menu

The Active Alarms menu filters and displays only active alarms for the MA PDU. Active alarm screens have priority over other screens. When an alarm occurs, the Active Alarms screen replaces the current screen and

the backlight blinks in red and white (see Figure 35). Up to 100 active alarms can display.

On the Main Menu, scroll up or down to highlight Active Alarms. Press ENTER to display the first active alarm screen. Scroll up or down if needed to view active alarm data. When you finish your review, press ESC to return to the previous menu. If the backlight was blinking red to indicate an active alarm, the backlight returns to normal.

Main Menu

Alarms History

Meter

Control

Settings

PDU Info

Enter

Input frequency out of range

09/05/2011

14:23:32

Down

Input voltage low critical

09/05/2011

14:23:32

ESC

Main Menu

Active Alarms

Alarms History

Meter

Control

Settings

PDU Info

Enter

No alarms

ESC

Figure 35. Example Active Alarm Displays

Alarms History Menu

The Alarms History menu allows you to scroll through the last 50 logged alarms, beginning with the most recent alarm. The Alarms History screens contain the type of alarm, the date (MM/DD/YYYY), and time (hh:mm:ss)

when the alarm occurred (see Figure 36).



On the Main Menu, scroll up or down to highlight Alarms History. Press ENTER to display the most recent alarm in the history log. Scroll up or down to view the alarms. When you finish your review, press ESC to return to the previous menu.

Main Menu

Active Alarms

Meter

Control

Settings

PDU Info

Enter

Alarms History

Input frequency out of range

09/05/2011

14:23:32

Down

Alarms History

Input current high warning

09/05/2011

14:23:32

Down

Alarms History

Temperature high warning

07/07/2011

01:05:44

ESC

Figure 36. Example Alarm History Displays

Meter Menu

The Meter menu provides measurement data for the following submenus: l

PDU l

Sections (not available for sections that do not have current measurement) l

Outlets l

Environment (only available if an EMP is installed)

On the Main Menu, scroll up or down to highlight Meter. Press ENTER. Scroll up or down to select a submenu and press ENTER to display the submenu options. Press ESC to return to the previous menu.

Main Menu

ACTIVE ALARMS

EVENT LOG

Meter

OUTLET READINGS

SETTINGS ePDU INFO

Enter

Meter

PDU

Sections

Outlets

Environment

ESC

Figure 37. Example Meter Menu Display

NOTE

The measurement data for each screen is refreshed every three to four seconds.

PDU Submenu

These screens display Total Input data measurements for MA PDUs. In addition to Total Input measurements, you can view Phase Input data measurements for 3Ph, split-phase, and dual input MA PDUs. Depending on the

MA PDU electrical topology, different MA PDU measures will display in the Total Input and the Input Phase meter screens.

Table 7 shows which measures will be present:



Table 7. Measures for Total Input and Phase Input Meter Screens

Measure

Frequency

Voltage

Current

Percent Load

Active Power

Crest Factor

Apparent Power

Reactive Power

Power Factor

Energy

Peak Power

Total Input

•

—

•

•

•

—

—

—

•

•

•

Wye-wired Input Phase

•

•

—

—

—

•

•

•

—

—

—

Delta-wired Input Phase

—

•

—

—

—

•

•

•

—

—

—

Total Input Meter Data

On the Meter menu, scroll up or down to highlight PDU. Press ENTER to display the Total Input submenu for your 1Ph or 3Ph PDU. Press ENTER again to see Total Input meter data measurements. Scroll up or down to review other Total Input meter data measurements. After you review the data, you can press ESC to return to the Input Meter menu and select A, B, or C to see Phase Input measurements. Press ESC to return to the previous menu.

For example, Figure 38 shows a total input display for 1Ph MA PDUs.

Meter

PDU

Sections

Outlets

Environment

Enter

ESC

PDU Meter

Enter

Total Input

Frequency

50.23 Hz

Active Power

100 W

Down

Total Input

Apparent Power

120 VA

Reactive Power

20 VAR

ESC

Total Input

Peak Power of xxxx W since

07/01/2011

17:32:23

Figure 38. Example 1Ph Total Input Display

Total Input

Down

Energy

16.238 kWh since

07/01/2011

17:32:23

Down

Total Input

Power Factor

0.912

NOTE

The Total Input > Input Meter selection screens will be different for 1Ph and 3Ph

MA PDUs.



Figure 39 shows an input phase display for wye-wired 3Ph MA PDUs.

Meter

ACTIVE ALARMS

EVENT LOG

OUTLET READINGS

SETTINGS ePDU INFO

Enter

ESC

C

Input Meter

Total Input

A

Enter

B

B Voltage

230.25 V

Down

ESC

B

Current

1.256 A

Percent Load

15 %

Down

B

Active Power

100 W

Crest Factor

1.524

Figure 39. Example 3Ph Input Phase (wye-wired) Display

Sections Submenu

Section measurements include voltage data for all MA PDU sections. Other sections measurements are only

available on MA PDUs that have current measurement capabilities (see Figure 40).

On the Meter menu, scroll up or down to highlight Sections. Press ENTER to display the Sections submenu.

Scroll up or down to review the data for your selection. After you review the data, press ESC twice to return to the previous menu.

Meter

PDU

Sections

Outlets

Environment

Enter

L1

L2

L4

L5

Section

ESC

Figure 40. Example Section Submenu Display

Outlets Submenu

On the Meter menu, scroll up or down to highlight Outlets. Press ENTER to display the Outlets submenu.

Scroll up or down to review the data for your selection. After you review the data, press ESC twice to return to

the previous menu (see Figure 41).



Meter

PDU

Sections

Outlets

Environment

L1

Enter

ESC

L3

L4

L5

Outlet

ESC

Enter

L2

Current

Active Power

100 W

L2

Energy

16.238 kWh since

07/01/2011

17:32:23

Down

Down

L2

Apparent Power

120 VA

Reactive Power

20 VAR

Down

L2

Crest Factor

1.524

Power Factor

0 .853

Figure 41. Example Outlets Submenu Display

Environment Submenu

The Environment submenu provides temperature and humidity data for the EMP. This menu is only available if an EMP is installed.

On the Meter menu, scroll up or down to highlight Environment. Press ENTER to display the Environment submenu. Press ENTER to review the data for your selection. After you review the data, press ESC to return to the previous menu. (Contact closures are not displayed on the LCD.)

Meter

PDU

Sections

Outlets

Enter

Environment

Temperature:

24.3 °C

Humidity:

23.5 %

ESC

Figure 42. Example Environment Submenu Display



Control Menu

On the Main Menu, scroll up or down to highlight Control. Press ENTER. Scroll up or down to see a list of outlet group IDs. Select an outlet group. The On/Off drop down list displays. Select On or Off. The selected state of the outlet displays. Scroll up or down to see other lists of outlet group IDs (if available). Press ESC to return to

the previous menu (see Figure 43).

Active Alarms

Alarms History

Meter

Settings

PDU Info

Enter

A1 On

A2 On

On

A4

On

Off

A5 On

ESC

Enter

B1 On

On

B3

On

Off

B4 On

B5 On

Figure 43. Example Control Submenu Display

Settings Menu

The Settings menu provides user configuration options. Only the available options display, depending on the assigned user privileges.

There are five standard Settings submenus and one optional submenu: l

USB Flash mode (only available if the USB device is detected) l

Display l

Daisy Chain l

Language l

IPv4 l

Factory

On the Main Menu, scroll up or down to highlight Settings. Press ENTER. Scroll up or down to select a submenu and press ENTER to display the submenu options. Press ESC to return to the previous menu.

Active Alarms

Alarms History

Meter

Control

Settings

PDU Info

Settings

Enter

Daisy Chain

IPv4

Language

Factory

ESC

Figure 44. Example Settings Menu Display



USB Flash Mode Submenu

The “USB Flash Mode Submenu” displays in the Settings menu when a USB device is detected in the USB port. The menu selection does not display when the USB device is removed.

Settings

Active Alarms

Alarms History

Meter

Control

Settings

PDU Info

Enter

Display

Daisy Chain

IPv4

Language

Factory

Enter

ESC

Figure 45. Example Settings USB Flash Mode Menu Display

Save Config.

Load Config.

Upgrade F/W

Save eNMC file

Load eNMC file

Exit

ESC

Save User-Customized Settings Configuration Files to the USB

This LCD menu option allows you to save the user-customized configuration settings files to the USB drive.

These files contain your custom settings, such as network parameters, outlet names, and threshold values. If you have several MA PDUs of the same model and hardware configuration, you can copy the customized setting files from one MA PDU and upload the files to the rest of the MA PDUs. This will help ensure consistency of the settings and save set-up time.

After this procedure is completed, the following files will exist on the USB device: l eNMC/config/ConfigurationData.xml - Contains all network and communication-related settings. This can be saved from and loaded to any MA PDU when replicating configurations regardless of part number.

l eNMC/config/ConfigurationPdu.xml - Contains all the user-configurable settings related to the MA PDU itself such as voltage and current thresholds, customized naming, and outlet control parameters. The structure of this file depends on the part number so that it cannot be duplicated from PNx to PNy (part number x to part number y).

To save the user data configuration settings files to the USB drive:

1.

Make sure the eNMC module is power ON.

2.

Insert a USB device in the USB port. Verify the USB drive contains the eNMC/config directory located at root of USB drive.

3.

When the pop-up confirms that the USB is detected, click OK, and then press Enter to return to the Main

Menu. (If not confirmed within 10 seconds, the pop-up goes away by itself.)

4.

Under Settings, select USB Flash Mode.

5.

The eNMC module restarts. (If there is no action within one minute, the eNMC module exits the USB

Flash mode. Remove and reinsert the USB drive to access this menu again.)

6.

Select Save Config.

7.

Click OK to continue when a successful pop-up message displays the following: l

The ConfigurationData.xml file is saved in the eNMC/ config directory on the USB drive.

l

The ConfigurationPdu.xml file is saved in the eNMC/ config directory on the USB drive.

8.

Remove the USB drive and select Exit.



Load User-Customized Settings Configuration Files from the USB

This option loads the ConfigurationData.xml and ConfigurationPdu.xml files into the eNMC module from the

USB device. The new parameters in these files will be applied when the eNMC module exits USB Flash Mode.

When this option is selected, the eNMC module will first attempt to load the eNMC/config/

ConfigurationData.xml file from the USB device. Next, the eNMC module will attempt to load the eNMC/config/

ConfigurationPdu.xml file from the USB device.

1.

Verify that the USB drive contains the ConfigurationPdu.xml file and ConfigurationData.xml files in eNMC/config directory of USB drive.

NOTE 1

The eNMC/config directory contains only these two files.

NOTE 2

The ConfigurationPdu.xml file is compatible with a specific MA PDU part number.

2.

Make sure the eNMC module is powered ON.

3.

Insert a USB drive.

4.

When the pop-up confirms that the USB is detected, click OK then press Enter to go to the Main Menu.

(If not confirmed within 10 seconds, the pop-up goes away by itself.)

5.

Select USB Flash Mode from the Settings menu. The module restarts.

6.

Select Load Config then click OK to start loading the ConfigurationData.xml file into the eNMC module.

7.

When the file is successfully loaded, click OK in response to the confirmation message.

8.

Click OK to start loading the ConfigurationPdu.xml file into the eNMC module.

9.

When the file is successfully loaded, click OK in response to the confirmation message.

10. Remove the USB drive and select Exit from the USB Flash Mode menu.

Save the PDU Hardware Configuration File to the USB

See “Replace the MA PDU eNMC Module” on page 121 to understand this selection in proper context. This

procedure is used as part of the eNMC module replacement procedure. Each eNMC module has a hardware configuration file that can only be used on the specified MA PDU model. This procedure allows you to copy the

PDU hardware configuration file from a working eNMC module of the same model and store it on a USB flash drive so that it can be uploaded to a new eNMC module.

To save the MA PDU model-specific hardware configuration file to a USB drive:

1.

Make sure the eNMC module is powered ON. Connect a USB flash drive to a working MA PDU.

!

IMPORTANT

This MA PDU must be of the same model type and configuration as the MA PDU that houses the eNMC you will replace.

2.

When the LCD interface pop-up confirms that the USB flash drive is detected, click OK, and press Enter to return to the Main Menu. (If not confirmed within 10 seconds, the pop-up goes away by itself.)

3.

From the LCD Settings menu, select USB Flash Mode. Press Enter, select yes to confirm, and then press

Enter again. The module restarts. (If there is no action within one minute, the eNMC module exits USB

Flash Mode. Remove and reinsert the flash drive to access this menu again.)



4.

Select Save eNMC file to save the MA PDU hardware configuration file to the USB drive. The file will save to the eNMC/config/hw path at the USB drive root directory.

NOTE 1

The eNMC/upgrade/hw directory contains only one file named epdu_cfg_HPModelNumber_HP AssemblyNumber_vx_x.xml.

For example, the HP file name for model H8B48A would be: epdu_cfg_H8B48A_767160-001_vx_x.xml (where x_x is a file revision).

NOTE 2

The epdu_cfg*.xml file shall be compatible with the eNMC module part number.

5.

See Table 8 and confirm the name of the file correctly matches your model.

Table 8. Configuration File Names

Model MA PDU Model Configuration File Names Description

H8B48A

H8B49A

H8B50A

H8B51A

H8B52A

H8B53A

H8B54A

H8B55A epdu_cfg_H8B48A_767160-001_vx_x.xml

epdu_cfg_H8B49A_767160-002_vx_x.xml







HP 2.8kVA 120V 30A NA/JP maPDU

HP 3.6kVA 100-240V 16A WW maPDU


HP 7.3kVA 200-240V 32A INTL maPDU

HP 8.6kVA 208V 30A 3Ph NA/JP maPDU

HP 8.6kVA 208V 30A 3Ph DV NA/JP maPDU

HP 11kVA 400V 16A 3Ph INTL maPDU


H8B56A epdu_cfg_H8B56A_767160-009_vx_x.xml


NOTE

The version of the file is represented by vx_x, where x_x = number of the version. For example, a version 2.0 file would be represented as, “epdu_cfg_H8B48A_767160-001_v2_0.xml” in the file name.

6.

When the file is saved, click OK to confirm.

Load the PDU Hardware Configuration File from the USB to the eNMC Module

See “Replace the MA PDU eNMC Module” on page 121 to understand this selection in proper context.This

procedure is used as part of the replacement procedure.

The MA PDU hardware configuration file provides the replacement eNMC module with the characteristics of the MA PDU model in which it resides, such as the type of input, the number of circuit breakers and outlets, and the way measurements should be displayed. Use this menu selection to upload the PDU model-specific hardware configuration file to the replacement eNMC module.

NOTE

This selection will only display in the menu if an MA PDU hardware configuration file is detected on the USB drive.

To load the MA PDU model-specific hardware configuration file to an eNMC module:

1.

Make sure the eNMC module is powered ON. Connect the USB flash drive to the MA PDU with the new eNMC module.

2.

When the LCD interface pop-up confirms that the USB flash drive is detected, click OK, then press Enter to return to the Main Menu. (If not confirmed within 10 seconds, the pop-up goes away by itself.)

3.

From the LCD Settings menu, select USB Flash Mode. Press Enter, select yes to confirm, and then press

Enter again. The module restarts. (If there is no action within one minute, the eNMC module exits USB

Flash Mode. Remove and reinsert the USB flash drive to access this menu again.)



4.

Select Load eNMC file, then click OK to upload the MA PDU hardware configuration file to the eNMC module.

5.

When the file is successfully loaded, click OK to confirm.

6.

Remove the USB flash drive and select Exit.

Upgrade the Firmware using USB

To upgrade the eNMC module firmware:

1.

Obtain the hardware configuration file in one of the following ways: l

Copy the hardware configuration file from another working MA PDU (must be the same model type and configuration).

l

Go to http://www.hp.com/go/rackandpower. Download the firmware upgrade package from the HP

Web site and use the attached configuration files for your model.

2.

Save the MA PDU model-specific hardware configuration file to your computer. See Table 8 on page 50.

NOTE

The file is named Image*.bin.

3.

Connect a USB drive to your computer and put the Image*.bin file in the eNMC/upgrade/ location on the

USB drive root directory.

NOTE

There can only be one Image*.bin file in the eNMC/upgrade directory on your USB drive.

4.

Make sure eNMC module is powered ON.

5.

Insert the flash drive in the USB port of the eNMC module front panel.

6.

When the pop-up confirms that the USB is detected, click OK, and then press Enter to return to the Main

Menu. (If not confirmed within 10 seconds, the pop-up goes away by itself.)

7.

Select USB Flash Mode. Click Yes to confirm you want to enter the USB Flash mode. (If there is no action within one minute, the eNMC module exits the USB Flash mode. Remove and reinsert the USB drive to access this menu again.) The module restarts.

8.

Select Upgrade FW and click OK to confirm the upgrade. The eNMC module gets the file from the USB drive.

9.

A few seconds after 100% is reached, the eNMC module restarts and then enters in Boot upgrade mode to continue upgrade. The upgrade is finished when the eNMC module is restarted. This can take several minutes.

Exit

Select Exit to leave USB Flash Mode.

Display Submenu

The Display submenu allows you to customize settings for LCD contrast and orientation (see Figure 46).

On the Settings menu, scroll up or down to highlight DISPLAY. Press ENTER to display the screens to set the values for the submenu. After you select the values, press ENTER to set the values as displayed on the screen.

Press ESC to return to the previous menu.



Settings

Daisy Chain

IPv4

Language

Factory

Enter

LCD

Contrast:

35

Orientation:

0 °

ESC

Figure 46. Example Display Submenu Displays

Enter

LCD

180°

0 °

Enter

Daisy Chain Submenu

The Daisy Chain submenu allows you to configure two to four MA PDUs to be monitored from a single Ethernet connection on the Host MA PDU. Use the Daisy Chain submenu options (Settings and Discovery) to configure the MA PDUs.

!

IMPORTANT

All daisy-chained PDUs should be MA PDUs. Daisy-chaining MA PDUs with any other type of PDU will generate an error.

NOTE 1

To configure and monitor the MA PDUs, they must be connected together through the Daisy Chain connector on the front panel using an Ethernet cable.

NOTE 2

The Host MA PDU must be connected to the network. There can only be one Host.

Use the Settings option for the first two configuration steps:

1.

From the MA PDU (or MA PDUs) designated as a Device MA PDU, access the Daisy Chain Settings option and set the Device values.

2.

From the MA PDU designated as the Host MA PDU, access the Daisy Chain Settings option and set the

Host values.

Use the Discovery option for the final configuration step:

3.

From the Host MA PDU, access the Daisy Chain Discovery option to start communication between the

Host and the Device MA PDU (or MA PDUs).

Daisy Chain Settings Options

The Daisy Chain Settings option allows you to specify the MA PDU that will be the Host (the MA PDU that has the network connection) and the MA PDU (or MA PDUs) that will be connected to it as Devices.

From the Device MA PDU (or MA PDUs), set the values as follows (see Figure 47):

1.

On the Settings menu, scroll up or down to highlight Daisy Chain and press ENTER.

2.

Scroll up or down to highlight Daisy Chain and press ENTER.

3.

Select 1 (Device), 2 (Device), or 3 (Device), from the Id: selection drop-list. Press ENTER.

4.

Select End or Middle from the Place: selection drop-list. Press ENTER.



NOTE 1

Select End when the PDU is adjacent to only one other PDU.

NOTE 2

Select Middle when the PDU is located between two other PDUs.

NOTE 3

Always select End when assigning the last device in the chain when daisy-chaining three or four MA PDUs.

5.


Settings

Display

IPv4

Language

Factory

Enter

ESC

Daisy Chain

Enter

Daisy Chain

Id: 0 (Host)

Place

0 (Host)

2

(Device)

3 (Device)

Id:

Daisy Chain

1 (Device)

Enter

Place:

Middle

Middle

End

Enter

ESC

Figure 47. Example Daisy Chain Device MA PDU Setup

From the Host MA PDU, set the values as follows (see Figure 48):

1.

On the Settings menu, scroll up or down to highlight Daisy Chain and press ENTER.

2.

Scroll up or down to highlight Settings and press ENTER.

3.

Select 0 (Host) from the Id: selection drop-list. Press ENTER.

4.

Select End from the Place: selection drop-list. Press ENTER.

5.


Settings

Display

IPv4

Language

Factory

Daisy Chain

Enter

Discovery

ESC

Enter

Id:

Daisy Chain

0 (Host)

0

(

Host

)

1 (Device)

)

Place:

End

Id:

Daisy Chain

0

(

Host

)

Enter

Place: Middle

Middle

End

Enter

ESC

Figure 48. Example Daisy Chain Host MA PDU Setup

Daisy Chain Discovery Options

The Discovery option starts communication between the Host MA PDU and the Device MA PDU (or PDUs).

This is only available for the Host MA PDU. The display you see varies depending on whether the MA PDU is

communicating properly or not communicating (see Figure 49 and Figure 50).

From the Host MA PDU, perform a Discovery as follows:

1.

On the Settings menu, scroll up or down to highlight Daisy Chain and press ENTER.

2.

Scroll up or down to highlight Discovery.

3.

Press ENTER to perform the discovery.


LCD Interface Operation l

When the discovery completes successfully, the Media Access Control (MAC) address of the Device

MA PDU displays (see Figure 46). Go to Step 4.

l

If there is no connection, the “No device chained” error message displays (see Figure 47). Go to the

Daisy Chain Settings option screens and reset the values to correctly identify the Host. Once corrected, then select the Discovery option again.

l

If the Host and Device MA PDUs have been incorrectly identified, a “Host Conflict” error message displays. Go to the Daisy Chain Settings option screens and reset the values to correctly identify the

Host and Device (or devices). Once corrected, select the Discovery option again.

4.

Press ENTER to validate the Discovery.

5.


Settings

Display

IPv4

Language

Factory

Enter

ESC

Daisy Chain

Settings

Discovery

Enter

Daisy Chain

MAC @: XX:XX:XX

XX:XX:XX

Device: 1

Place: End

OK

ESC

Figure 49. Example Daisy Chain MA PDU Discovery (Communicating)

Enter

Settings

Display

IPv4

Language

Factory

Enter

ESC

Daisy Chain

Settings

Discovery

Enter

Daisy Chain

No device chained

ESC

Figure 50. Example Daisy Chain MA PDU Discovery (Not Communicating)

Enter

IPv4 Submenu

The IPv4 submenu allows you to set options for: l

DHCP l

IP address l

Subnet Mask l

Gateway

Figure 51 shows the IP Address displays.

On the Settings menu, scroll up or down to highlight IPv4. Press ENTER to display the options screen. Scroll up or down to highlight the selected option from the menu. Press ENTER to display the screens to set the values for the selected option. After you select the values, press ENTER to set the values as displayed on the screen. Press ESC to return to the previous menu.



Settings

ACTIVE ALARMS

EVENT LOG

OUTLET READINGS

SETTINGS

Enter

ESC

IPv4 Settings

DHCP

Subnet Mask

Gateway

ESC

Figure 51. Example IPv4 Submenu Displays

Enter

ESC

192

IP address

168

1

OK

2

IP address

192

Enter

1

ESC

Enter

OK

168

2

Language Submenu

On the Settings menu, scroll up or down to highlight Language. Press ENTER. Scroll up or down to highlight the selected language option from the menu. Press ENTER to set the selected language. Press ESC to return

to the previous menu (see Figure 52).

NOTE

Available languages include English, French, German, Spanish, Portuguese, and

Italian. (Russian is not currently available.)

Settings

Display

IPv4

Enter

Language

English

Français

Deutsch

Español

3ɭɫɫɤɢɣ

Português

Italiano

ESC

Figure 52. Example Language Setting

Factory Submenu

The Factory submenu allows you to reset the MA PDU to the factory settings (see Figure 53).

On the Settings menu, scroll down to highlight Factory. Press ENTER to display the screens to set and confirm the return to factory settings. After you make the selections, press ENTER to set the values as displayed on the screen. Press ESC to return to the previous menu.

Settings

Display

Daisy Chain

IPv4

Language

Factory

Enter

Factory

Return to

Factory

Settings?

Yes

No

Enter

ESC

Figure 53. Example Factory Submenu Displays

Factory

Confirm...

OK Cancel

Enter



MA PDU Info Menu

The MA PDU Info menu provides identification information for this MA PDU. The identification information includes the MA PDU model type and part number, serial number, eNMC firmware version number, IP address,

and eNMC MAC (Media Access Control) address. These are information-only screens (see Figure 54).

On the Main Menu, scroll up or down to highlight MA PDU Info. Press ENTER to navigate to each screen. Scroll up or down on the screen if needed to view the MA PDU information displays. Press ESC to return to the previous menu.

Main Menu

Active Alarms

Alarms History

Meter

Control

Settings

PDU Info

Enter

PDU Info

Type Model

HP PDU

Part Number

H8B49A

Enter

PDU Info

Serial Number xxxxxxxxxx

Firmware Version xx .xx .xxxx

Enter

PDU Info

MAC Address xx: xx: xx:xx:xx:xx

IPv4 address

ESC

Enter

PDU Info

IPv6 address xxxx:xxxx:xxxx:xxxx xxxx:xxxx:xxxx:xxxx

Figure 54. Example MA PDU Info Display


Chapter 7 Web Interface Operation

This chapter describes remotely configuring, managing, and monitoring an HP Managed PDU remotely through the eNMC module Web interface. This chapter describes the following: l

Navigating the Web interface l

Accessing the Web interface l

Configuring settings and monitoring the MA PDU

NOTE

When the Web browser is set to 100% (full page), we recommend setting your screen resolution to a minimum of 1024 x 768 for the best display performance.

Navigate the Web Interface

The graphical Web interface is used to remotely monitor or configure the MA PDU (see Figure 55). The Web

interface that corresponds to the MA PDU topology type displays. This section describes the functions provided by this interface.

1 2 3

10

4

9

8

5

7

Figure 55. Navigating the Web Interface (Opening Page)

6


Web Interface Operation

Table 9 provides descriptions of the Web interface components.

Table 9. Web Interface Region Descriptions

Area Description

1 - Application Header Bar

The header bar identifies which PDU Web application is within the host window.

2 - Menu Selection Page Display

As each menu link is selected, the corresponding information displays as the main page. The top of the page displays the menu selection title.

3 - Host Window

4 - Outlet Icons

NOTE

You can expand your view of the contents vertically using the elevator scroll button on the side of the page. If you need more window viewing area, resize the Host Window to a wider or taller size. This enlarges the main page.

The host window is the page where the application resides. Both the height and the width of the host window can be resized. The application panels resize at the same time. An elevator scroll button displays on the side of the application panel if the panel cannot display the entire list within the resized panel. Drag the elevator scroll button up or down to view the entire list of data in the application panel.

Roll over any outlet icon to see the type of outlet and whether there is an alarm. (A gray outlet status indicates that the outlet management feature could be damaged.) The borders around the outlet groups emulate the colors that are printed on the PDU.

Outlet is Off

Outlet is on

5 - Operation Buttons and Icons

6 and 7- Current Alarms (when active)

Operation buttons and icons are provided to save data entries and updates. Enter data by typing or selecting entries and clicking the associated button. Some pages have buttons for specialized functions, such as clearing accumulated data logs. File operation icons are also provided to save or download files.

An indicator appears as a notification in the refresh bar at the bottom of the page. For example,

“Warning, some alarms fired, please refer to the Active Alarms | Last Refresh: dd/mm/yyyy -

hh:hh:ss”

The words “Active Alarms” in the alarm notification sentence link to the Active Alarms page.

The following symbols indicate the alarm level when an alarm threshold setting is exceeded:

Active Alarms Present

High Critical Threshold Alarm

High Warning Threshold Alarm

Low Warning Threshold Alarm



Table 9. Web Interface Region Descriptions (Continued)

Area

8 - MA PDU Information

Description

This panel displays identification information for the MA PDU that is providing data. The data fields include information about the MA PDU, including a model description, part number, serial number and the current MA PDU firmware version in use.

NOTE

For daisy-chained PDUs, you can select either PDU [0] for Host data and PDU [1], [2], or [3] for Device data. This displays data for the selected PDU.

9- Active Alarms Menu Selection

This indicator alerts you to the presence of currently active system alarms. It is in the menu hierarchy. When alarms are active, the text for Active Alarms is red. Selecting Active Alarms opens the Active Alarms page and displays the current active alarms.

10 - Menu Bar

The menu bar on the left panel contains links to pages for configuring the system or managing and monitoring the MA PDU. The menu hierarchy is expandable and collapsible. You can move the menu bar out of view using the horizontal scrolling tab at the bottom of the page.

Click any selection in the menu bar to retrieve MA PDU performance data, review operation log information, or retrieve system or network configuration settings. The data on the selected page is presented in table format.

NOTE 1

The data that displays on the Web interface depends on the MA PDU model you are using, or models if you daisy-chain PDUs.

NOTE 2

The Web interface supports Microsoft

®

Internet Explorer

®

8.0 and greater, Firefox

®

(installed on Linux

®

or Windows

®

), and Google

®

Chrome

®

.

NOTE 3

On most pages, you can display relevant tooltips as you roll over images and fields.

Languages

The Web interface language is configurable. The following languages are available for your selection: l

English l

French l

Spanish l

German l

Italian l

Chinese Simplified l

Japanese l

Korean l

Chinese Traditional l

Russian (currently unavailable) l

Polish l

Portuguese l

Czech

Access the Web Interface

The Web interface can be accessed using a standard Web browser.

NOTE

The MA PDU defaults to using DHCP when delivered. If you are unable to connect to the MA PDU through the network connection with this default address, see

“Network Communication Configuration” on page 28 for more information.



To access the Web interface:

1.

Open the Web browser.

2.

Enter a new MA PDU IP address or select the previously entered MA PDU IP address from the URL address drop list. The Authentication dialog displays.

3.

Enter a valid user name and password in the Authentication dialog box (see Figure 56). Click Login to

continue or Cancel to exit.

NOTE

The default user name is “admin” and the default password is “admin.”

Figure 56. Login Authentication

4.

The MA PDU Overview page displays.

5.

To access another page to observe and control the PDU, click any selection in the menu bar. The page that corresponds to your menu selection opens and displays in the main selection page window.

Menu Selections

Depending on the permission level of the user, the Menu Bar provides up to four groups of selections: l

Power Management

- Overview l

PDU [0]

See NOTE 1 l

PDU [1] See NOTE 1 l

PDU [2]

See NOTE 1 l

PDU [3] See NOTE 1

- Groups

- Outlets

- Environment l

- Active Alarms

Logs and Notifications

- Logs

- Trap Notification l

- Syslog (Super User and Administrator only)

Settings

See NOTE 2

- Access Accounts

- System



- Date & Time l

Network (Super User and Administrator only)

- TCP/IP

- SNMP

- Energy/Wise

- Security l

Global l

LDAP l

RADIUS

NOTE 1

Menu selections for PDU [0], [1], [2], or [3] only display if the MA PDUs are configured in a daisy-chained configuration. If provided, selecting either PDU [0] or

PDU [1], [2], or [3] displays the Overview page for the specified MA PDU only.

NOTE 2

The Settings menu is different from the Settings button. Selecting the Settings button on any power management page displays a separate window that allows you to change settings, such as alarm thresholds.

Your access privileges determine what menu selections you can see. See “Access Privileges” on page 62 for

more information about levels of access privileges.

Power Management

Use the Power Management menu selections to see up-to-date operating measurements on the MA PDU

Overview page. This page provides the present readings for the MA PDU that is reporting data. (If MA PDUs are daisy-chained, you can select to see Host or Device MA PDU Information.) The readings are reported per phase and, for 3Ph MA PDU models, all phases. This page includes data such as current, voltage, and crest factor. The outlet icons are green if the outlet is on and red if the outlet is off. Roll over the icon to see the outlet type and status.

You can select the Outlets or Groups page to manage outlets or groups of outlets. These Settings pages provide present measurements or readings such as current or active power. You can set measurement thresholds for alarm or warning notifications as well. You can also set power schedules for outlets.

On the Outlet Settings dialog, the Power Schedule section allows you to schedule automatic power On, power

Off, or Reboot actions for selected outlets. These schedules can be set for a single instance, daily or weekly activity at specified time intervals.

The Environment menu selection provides humidity and temperature data if you have an EMP installed. You can set measurement thresholds for alarm or warning notifications as well. It also provides open or closed status for two dry contacts.

You can check current alarms on the Active Alarms page to see a list of alarms by date, time, and description.

See “Maintenance and Alarms” on page 121 for a list of alarms.

Logs & Notifications

Use the Logs & Notifications menu selections to see a list of the most recent events (Logs page). You can set trap receivers (Trap Notification page) and you can also view Syslog information.



Settings

The Settings menu selections that display depend on the type of privilege you have. These selections allow you to configure administrative settings, system attributes, and network access and control. Depending on privilege, this menu can include the following: l

Access Accounts: The Access Accounts page allows you to set up the SuperUser, local or remote administrators, local MA PDU-users, and remote MA PDU-users as individuals or groups. Access Accounts also allows the SuperUser to set up the LCD password.

l

System: Use the System selection for identifying the administrator contact information, uploading an MA

PDU or eNMC module configuration file, upgrading, restarting, or restoring factory default configuration to the PDU eNMC module. You can also reset the language and configure reporting for the EMP.

l

Date & Time: The Date & Time page allows you to select the date format and set the date and time, either manually or by synchronizing with the NTP (Network Time Protocol) server. You can set the time zone and have the option of allowing DST (Daylight Savings Time).

Network

This selection allows you configure TCP/IP, SNMP, and Security settings for this PDU.

l l

TCP/IP: Use this page to configure Ethernet, IPv4, IPv6, DNS, and SMTP.

SNMP: Use this page to configure general SNMP settings, SNMPv1 settings, and SNMPv3 settings. You can also access the HP MA PDU MIB (Management Information Base) from this page.

l

Energy/Wise: Use this page to enable or disable the Energy Wise feature.

l

Security: Use this page to set port settings and LDAP (Lightweight Directory Access Protocol) settings.

- Global: Set the port settings and the authentication mode on this page.

- LDAP: Set the LDAP search configuration and global LDAP server global parameters for the specified

LDAP servers on this page.

- RADIUS: Add or edit the parameters for a primary or secondary RADIUS server on this page.

Access Privileges

The level of access privilege determines what the user will see and what actions the user can perform. For example, the level of access privilege determines which menu items the user can access or which fields display on individual setting and configuration dialogs. Any menu or dialog functions that are not included in the access privilege set for a user do not display, or are they are grayed-out.

These accounts can be configured not only for individuals, but also for groups. All remote users and administrators belong to a remote group and their access privileges are defined from this group. Remote

accounts also provide a way to attach LDAP users (see “Configure Remote Group Access” on page 76).

User roles can be assigned these access privilege levels: l

SuperUser Administrator l

Local or Remote Administrators l

PDU-User

SuperUser Administrator

There can be one SuperUser and up to eight standard local or remote administrators.

Only one user can be the SuperUser Administrator. This defaults to the local user, but a SuperUser should be assigned at first connection. This account is not accessible or editable by the standard administrators or MA

PDU-Users/Outlet Users.



The SuperUser always has read-write privileges to view and edit all data, plus the following privileges restricted only to the SuperUser: l

Exclusive access to modify the SuperUser account settings l

Can upload the communication module configuration file or upgrade the firmware l

Can access both the Serial interface and the Web interface l

Exclusive access to the Network and Date and Time Settings menu

NOTE

The default Administrator login and password is “admin” and should be changed at the first connection. If the administrator loses the password or login, contact your service representative to recover it.

Local or Remote Administrator

Up to eight standard administrators (local or remote) can be assigned. Only accessible menu items display for the user according to the assigned permissions.

Read-Write Access

A local or remote administrator who is assigned read-write access can perform the following: l

Access to up-to-date PDU data and measurements l

Create, modify, or disable an administrator or user account except for the SuperUser l

Configure e-mail recipient addresses for e-mail notification to users l

Restart the communications module l

Cannot access the Serial interface; must use the Web interface only l

Access all menus on the Web interface l

Access to retrieved PDU up-to-date data and measurements l

Clear logs l

Local Administrator Only. Can upgrade firmware.

Read-Only Access

A local or remote administrator with read-only access has limited privileges, including: l

Access to up-to-date PDU data and measurements l

Has the authority to change the password, but not the login (Remote PDU-Users cannot change the login or password) l


Can access the log and notifications submenu, but cannot clear the logs data l

Cannot configure the TCP/IP, SNMP Global Security, and LDAP settings

No Access

An administrator with no access is not authorized to access to the Web page.



Local or Remote PDU-User

Read-Write Access

A local or remote PDU-User with read-write access privileges has access to the same functions as the administrator, except this user cannot change the account configuration for another user, such as e-mail addresses for notifications.

Only accessible menu items display for the user according to the assigned permissions.

Read-Only Access

An PDU-User with read-only access has limited privileges, including: l

Access to up-to-date MA PDU data and measurements l

Has the authority to change the password and e-mail address, but not the login

(Remote PDU-Users cannot change the login or password, but can change their own e-mail address.) l


Can access the log and notifications submenu, but cannot clear the logs data l

Cannot configure the TCP/IP, SNMP Global Security, and LDAPsettings l

Cannot upload the communication module configuration file or upgrade the firmware l

Cannot change his profile or another user’s account

No Access

An PDU-User with no access privileges is not authorized to access to the Web page.

Session Management

The following session management restrictions apply: l

There can only be one SuperUser with read-write access rights and up to eight multi-users with configurable access rights.

l

When the administrator connects, any existing read-write sessions are closed. The other user (or users) will be asked to authenticate and open a new read-only session.

l

If a user with read-write access is logged in and another user with read-write access wants to log in, the following message displays: “Another user is logged in with R/W access. Continue as R/O?” l

PDU sessions are also limited in the following ways:

- Only five standard sessions without SSL (Secure Sockets Layer) or SSH (Secure Shell) sockets are allowed.

- Only two secure sessions can be running at the same time.

- Only an administrator can have two simultaneous sessions open in HTTP/HTTPS (Hypertext Transfer

Protocol / Hypertext Transfer Protocol Secure), Telnet/SSH.

NOTE

During an HTTP/HTTPS or Telnet/SSH session, the session times out if there is no activity for five minutes. After a session times out, you must login again.



Overview

Review/Modify the PDU Data

NOTE

Menu selections for PDU [0], [1], [2], or [3] only display if the MA PDUs are configured in a daisy-chained configuration. If provided, selecting either PDU [0] or

PDU [1], [2], or [3] displays the Overview page for the specified MA PDU only.

1.

Access the Web interface and log in.

2.

The PDU: Overview page displays.

3.

In the PDU Information panel, review PDU identification information.

4.

In the main page, review PDU monitoring data.

NOTE

The phase information that displays reflects the PDU model. For example, the number of phases that display depends on whether the PDU is a single-phase, split-phase, or three-phase model. The phase labels also change depending on whether the model is a delta-wired or a wye-wired model.

NOTE

Roll the cursor over an outlet icon to see the type of outlet and the status (On or

Off).

5.

To modify PDU voltage and current threshold values, click the Settings button located in the lower, right-hand corner of the Web interface screen. The Settings dialog displays.

6.

To enter new threshold values, type new values in any of the text boxes that follow, then click Save: l

Low warning current threshold l

High warning current threshold l

High critical current threshold l

Low critical voltage threshold l

Low warning voltage threshold l

High warning voltage threshold l

High critical voltage threshold

7.

To reset the threshold values to the default values, click Default, then click Save.

8.

To reset a kWh (kilowatt hour) counter to zero, click Reset kWh, then click Save.

NOTE

If you do not save the action, the kWh counter remains unchanged.

9.

To reset the maximum power counter to zero, click Reset Max Power, then click Save.

10. To cancel this action and return to the Overview page, click Cancel.



Groups

NOTE

In the toolbar, Turn On/Off Groups will only appear for PDUs with outlets that can be controlled.

Review/Modify the PDU Groups

1.


2.

Under Power Management, select Groups. The Groups page displays.

3.

Review basic monitoring information for Groups measurement settings.

NOTE

Click the red arrow next between the Current (%Load) and the voltage columns to see additional Section outlet information.

4.

For users with Read Write access. To apply an operative action to all outlets in a selected group, select the corresponding checkbox and select one of the following values from the Turn On/Off Groups drop-down list in the top bar, then click Save.

l

On: Turn on the selected group of outlets.

l

Off: Turn off the selected group of outlets.

l

Reboot: Reboot the selected group of outlets.

5.

To modify PDU threshold values for a specified group, click the link on the group friendly name. The Group

Settings dialog displays.

6.

Administrator or User with Read/Write privileges only. To specify the duration outlets in this group will be Off before switching On during a reboot, type the number of seconds the outlets should be Off in the

Power Reboot Period text box. Click Save.

NOTE

This setting overwrites the Power Reboot Period defined for individual outlets on the

Outlet Settings dialog.

7.




High critical current threshold l

Low critical voltage threshold l

Low warning voltage threshold l

High warning voltage threshold l

High critical voltage threshold

8.


9.

To reset a kilowatt hour (kWh) counter to zero, click Reset kWh, then click Save.

10. To reset the maximum current counter to zero, click Reset Max Current, then click Save.



Outlets

Review/Modify the PDU Outlets

1.


2.

Under Power Management, select Outlets. The Outlets page displays.

3.

Review basic monitoring information for individual outlets.

4.

Click the outlet name to display a dialog for renaming the outlet.

5.

To apply an operative action for a selected outlet, select the corresponding checkbox and select one of the following values from the Turn On/Off Groups drop-down list in the top bar, then click Save.

l

On: Turn on the outlet.

l

Off: Turn off the outlet.

l

Reboot: Reboot the outlet.

6.

To modify PDU threshold values for a specified outlet, click the link on the group friendly name. The Outlet


7.

To set whether an outlet state (On, Off, or Reboot) can be changed, check or uncheck the Enable

Switching check box, then click Save.

l

Disabled: Uncheck the check box to disable the setting, which indicates that the outlet state cannot be changed.

l

Enabled: Check the check box to enable the setting, which indicates that the outlet state can be changed.

8.

To set the state of the outlet with the PDU is powered on, select one of the following values from the

State on Device Startup drop-down list, then click Save: l

On: The outlet is powered after a duration of time set in the Outlet Switch On After field.

l

Off: The outlet is not powered.

l

Last Known State: The outlet is powered on if it was On when the PDU was powered Off. Otherwise, the outlet is not powered.

9.

Administrator or User with Read/Write/Control only. To specify the duration an outlet will be Off before switching On during a reboot, type the number of seconds the outlet should be Off in the Power

Reboot Period(s) text box. Click Save.

NOTE

This setting can be overwritten by the Power Reboot Period defined for groups of outlets on the Group Settings dialog.

10. To enter new threshold values, type new values in any of the text boxes that follow, then click Save: l



High critical current threshold

11. To reset the threshold values to the default values, click Default, then click Save.

12. To reset a kilowatt hour (kWh) counter to zero, click Reset kWh, then click Save.



Power Schedule

NOTE

Power schedules can be set by an Administrator with Read/Write/Control only.

Define a Power Schedule

1.


2.

Under Power Management, select Outlets. The Outlets page displays.

3.

Select an outlet and click the outlet name. The Outlet Settings dialog displays.

4.

Check the Power Schedule checkbox.

5.

Add an action in the first action block by selecting either On, Off, or Reboot from the drop-down list.

l

None: The actions in this schedule are not executed. This is the default upon opening this dialog. (You can use this setting to hold the settings for future activation.) l

Off: Select this value to switch off the current outlet according to the corresponding schedule you specify.

l

On: Select this value to switch on the current outlet according to the corresponding schedule you specify.

l

Reboot: Select this value to switch off and then switch back on the current outlet according to the corresponding schedule setting. The delay between the Off and the On can be set on the Outlet

Settings dialog using the Power Reboot Period field (see Step 9 on page 67). With this setting,

additional actions scheduled by the Further Actions selections are disabled.

6.

Set the time schedule for this action by selecting a time from the “at:” drop-down list.

7.

Set the date schedule for this action by selecting a date from the “Date of Action” selection calendar.

NOTE

“Date of Action” fields are only available when the “Recurrent” checkbox is unchecked. This field specifies the date when the action will be executed, but only

once. If your want the action to be scheduled to repeat, see Step 11.

8.

Optional. You can add additional scheduled actions. For example, suppose your first action is On. You can pair it with a subsequent Off action. The schedule for this second action is set by selecting Off from the

Further Action drop-down list and setting values in the date and time fields. By default, this second action is set to "None," meaning nothing more will happen.

l

None: The actions in this schedule are not executed at the specified time. This is the default if the

Action is set to Off or On. l

Off: Select this value to switch off the current outlet according to the corresponding schedule setting.

9.

Set the schedule for this action by selecting a date and time from the drop lists for the “at:” and Date of

Action” field.

NOTE

This date and time must occur after the date and time set for the first action.

10. Click Save.



Environment

11. Do you want to make the Power Schedule recurrent, so that specified schedules are executed multiple times?

If yes, go to Step 12.

If no, this procedure is completed.

NOTE

When a power schedule is recurrent, you set the schedule to repeat on specified days. To set any schedule, including recurrence, the Action or Further action cannot be set to “None.”

12. Check the Recurrent checkbox.

13. In the active days field, select which day or days to be affected by this action. When settings are saved, the “Date of Action” value is automatically set to the date of the first occurrence of the action.

14. Click Save.

Configure Environment Sensor Settings

1.


2.

Under Power Management, select Environment. The Environment page displays.

3.

In the Environment panel, review the present PDU environment monitoring temperature and humidity data. Also review the status of installed dry contacts, open or closed.

NOTE

The environmental monitoring data panel only displays data under these circumstances: l if the EMP is installed and configured in the system l if the user read-write access rights

NOTE

The environmental monitoring data panel displays the value of the last EMP value read as follows: l

When the EMP is disconnected, the startup value will be 0 (zero).

l

When the EMP is first connected, the startup value will be 0 (zero) because the last known reading was taken before a sensor was connected.

l

When the EMP remains connected, the startup value is the last known EMP reading.

4.

To modify environment threshold values, or to receive alarms when dry contacts change state, click the

Settings button located in the lower, right-hand corner of the Web interface screen. The Environment


NOTE

In the Environment Settings dialog, the measure column displays the present status or state of the dry contacts. This is a read-only column.

5.

To select default values for thresholds or dry contacts, click Default.



6.


Low critical humidity alarm threshold l

Low warning humidity threshold l

High warning humidity threshold l

High critical humidity alarm threshold l

Low critical temperature alarm threshold l

Low warning temperature threshold l

High warning temperature threshold l

High critical temperature alarm threshold

7.

To choose if you are notified when a dry contact state changes (Open or Closed), select one of the settings from the drop-down list under Open or Closed for the specified contact, then click Save: l

Informational: No alarm is generated.

l

Alarm: An alarm is generated when the specified dry contact is Open or Closed.

8.


9.

To cancel this action and return to the Environment page, click Cancel.

NOTE

To change the temperature scale to Celsius or Fahrenheit unit of measurement (°C

or °F), see “Set General System Settings” on page 77.

Active Alarms

NOTE

When the Active Alarms menu item in the menu bar list is red and displays an exclamation mark icon, an alarm is active.

Review Active Alarms

1.


2.

Under Power Management, select Active Alarms. The Active Alarms page displays.

3.

Ensure the PDU operation button in the upper left corner is not collapsed. If so, expand it to see the list of alarms.

4.

Review the alarm detection date/time, description, the threshold setting, and the value reading that triggered the alarm.

NOTE 1

The term “active alarms” indicates that the alarm is currently set. When an alarm is no longer active, it is removed from this page.

NOTE 2

The format of the date is set on the System Date & Time submenu (see

“Date & Time” on page 80).



Logs

Clear the Event Log

1.


2.

Under Logs & Notifications, select Logs. The Logs page displays.

3.

Click Clear.

NOTE

Only an Admin or PDU user with read-write access can clear the log. Click the arrow beside Type to sort the order of the columns, to apply filters to see the logs for a specific data type, or to sort all data in ascending or descending order.

Download the Event Log as a CSV File From the Web Interface

1.


2.

Under Logs & Notifications, select Logs. The Logs page displays.

3.

Click Save to File. The File Download dialog displays.

4.

Click Save. The Save As window displays.

5.

From the Save in drop-down list, specify where the file should be downloaded.

6.

Either accept the default file name (logevent.csv) or enter a new file name.

7.

Click Save.

NOTE

To import a CSV file in Excel, select the UTF-8 format.

NOTE

For daisy-chained PDUs: l

PDU type 00 indicates the Host PDU [0] logs.

l

PDU type 01 indicates the Device PDU [1] logs.

l


l


Download the Japanese-specific Event Log as a CSV File From the PDU to Excel

1.

Start Excel.

2.

On the Data tab, select Get External Data, then select From Text (see Figure 57).



Figure 57. Excel Data Tab Selections

3.

Browse and select the appropriate file with *.csv selected.

4.

Click Import. The Text Import wizard starts.

a.

Ensure that the Delimited option is selected. b.

In File origin, select 65001. In Unicode, select UTF-8. Click Next.

c.

In the Delimiters section, select Comma. Click Next.

d.

Click Finish.

5.

Select the destination for importing your data and click OK.

6.

Observe that the data appears in the spreadsheet with correct Japanese and English text (see Figure 58).

Figure 58. Japanese-specific CSV Event Log File

Trap Notification

Define the Trap Receivers

1.


2.

Under Logs & Notifications, select Trap Notification. The Trap Notification page displays.

3.

Click a linked Trap Receiver in the Name column to select the trap receiver to define.

4.

Type the name to identify the trap receiver. This value is not used to send traps.

5.

Choose one of the following protocols: l

Disable: The trap receiver is disabled. (No trap is sent to this user and the Test button is deactivated.) l

SNMP v1: Traps are sent over SNMPv1 protocol. (It must be compliant with the SNMP version defined

in “Enable/Disable the SNMP Agent” on page 83.)

l

SNMP v3: Traps are sent over SNMPv3 protocol. (It must be compliant with the SNMP version defined

in“Enable/Disable the SNMP Agent” on page 83.)

6.

Type the trap receiver IPv4 / IPv6 address or its host name.

7.

Type the trap community (public or private).



8.

From the On Event drop down list, select one of the following trap sources: l

Disable: The trap receiver is disabled and the Test button is deactivated.

l

All Alarms: The trap receiver is enabled.

9.

Click Save. If desired, test the configuration (see “Test Trap”).

10. Click Test. (See the“Test Trap”section that follows for more information).

Test Trap

NOTE

To receive the test trap #53, the trap receiver must be configured with a protocol

compliant with the one defined as the trap source (see “Enable/Disable the SNMP

Agent” on page 83).

This action consists of sending a test trap (#53) to all configured and enabled trap receivers. To achieve this action, the following requirements must be met: l

The eNMC module is running in Normal Operation mode.

l

The eNMC module is connected to the Local Area Network (LAN).

l

The eNMC module owns a valid IP address.

l

The SNMP must be enabled: SNMPv1, SNMPv3, or SNMPv1&v3.

The target trap receiver configuration requires a valid IP address and the trap receiver protocol must match the configured SNMP version.

NOTE

See “Enable/Disable the SNMP Agent” on page 83.

Syslog

Retrieve/Modify Syslog Data

1.


2.

Under Logs & Notifications, select Syslog. The Syslog Server page displays.

3.

Review to the Syslog status, the port number, and the protocol for the specified Syslog server.

4.

To enable or disable a server, click the check box beside the Syslog server name and click the Enable or

Disable button.

5.

To modify the settings for a server, click the Syslog name. The Syslog Server Settings dialog displays.



6.

In the Syslog Server Settings dialog, enable or disable the selected server from the Enable Server drop-down list. You can also change the following: l the port number and the protocol selection to either UDP or TCP from the Protocol drop-down list l the message transfer method according to:

- 5424: Syslog Protocol IETF

- 5425: TLS

- 5426: Transfer over UDP

- 6587: Transfer over TCP

- 3167: Syslog protocol IETF (obsolete) l the facility code used for all messages from 1 to 23 l the use of unicode byte order mask (BOM) according to RFC 5424

7.

When you finish modifying Syslog server settings, click Save or Cancel.

8.

(Optional). Click Test to test the configuration.

Access Accounts

Configure the SuperUser

1.


2.

Under Settings, select Access Accounts. The Access Accounts page displays.

3.

In the Admin Access panel, perform the following: l

Type the SuperUser login.

l

Type the SuperUser password.

l

Type the SuperUser password again.

4.

Click Save.

Configure the E-mail Notification Settings

NOTE 1

By default, an e-mail address is attached to each account.

NOTE 2

Any user can change his own e-mail address.

1.


2.


3.

In the Admin Access panel, click the e-mail address link.

4.

The e-mail recipient address displays. If needed, change the address.

5.

If needed, type the descriptive text to identify the e-mail receiver.

6.

Enable or disable the e-mail receiver in the status drop-down list.

7.

Check the Attached Files check box to attach the event log file to the e-mail sent to this receiver, or uncheck the box to send the e-mail without the event log file.

8.

Select the date of the next report using the date picker.

9.

Set the frequency of the report if this recipient should receive regular reports.



10. Set the time of delivery using the drop-down list.

11. From the On Event drop down list, select one of the following: l

Disable: E-mail delivery is disabled and the Test button is deactivated.

l

All Alarms: E-mail is enabled and the Test button is activated.

12. Click Test to send a test e-mail.

13. Otherwise, click Save or Cancel.

Configure the LCD Password

NOTE 1

Only an administrator can activate, deactivate, or modify the LCD password.

NOTE 2

There can only be one LCD password on the MA PDU.

1.


2.


3.

In the LCD Access panel, perform the following: l

Check the LCD Password check box to change the password.

l

Type the LCD password.

l

Type the LCD password again.

4.Click Save.

Configure Local User Access

NOTE 1

Only an administrator can create or modify a user account.

NOTE 2

Local users can use this user name and password for authentication if the authentication mode selected in the Network Security Global submenu is Local (see

“Set Authentication Mode” on page 87).

NOTE 3

The User name is used for authentication. It must be unique. If there is a name conflict when you are creating a new account, a warning message displays.

1.


2.


3.

In the Multi-User Access panel, select Add a local user from the Add drop down list. The Users Settings dialog displays.

4.

Perform the following: l

Type the user’s login user name to replace the default name.

l

Type the user’s password (minimum of five characters).

l

Type the user’s password again.



5.

Choose one of the following profile characteristics: l

Admin: This user has administrator privileges and controls the access of other users to the Web interface. The Administrator can restart the communications module, but cannot perform a firmware upgrade.

l

PDU User: This user has access to the PDU and either read only or restricted read-write privileges.

6.

Choose one of the following security levels: l

No Access: The user is not allowed to access the Web interface.

l

Read-Only: The user can access the Web interface, view the measures, and view the thresholds of the outlets and groups. This user is not allowed to change any settings or perform actions.

l

Read/Write: The user can access the Web interface, view the measures, and is allowed to change settings.

7.

To configure an e-mail address for this account, click the link of the e-mail address corresponding to this

user. See “Configure the E-mail Notification Settings” for more information.

8.

Click Save.

9.

To enable an e-mail address for this account, click the link on the e-mail address under the e-mail Address column.

Configure Remote Group Access

NOTE 1

A remote account is an account that will be created on the communications module in order to be attached to LDAP users so they can use the PDU. The account should already exist on the LDAP database.

NOTE 2

These LDAP users will use their LDAP login/password for authentication on the module.

1.


2.

In the Multi-User Access panel, select Add a remote group from the Add drop down list. The Remote

Group Settings dialog displays.

3.

Type the remote group login user name to replace the default name.

!

IMPORTANT

This login user name must match the group name that the user has in the LDAP database.

4.

Choose one of the following profile characteristics: l

Admin: This remote group has administrator privileges and controls the access of other users to the

Web interface.

l

PDU User: The administrator assigns this remote group either read only or read-write privileges to this user.

5.

Choose one of the following security levels: l


l

Read-Only: The remote group can access the Web interface, view the measures, and view the thresholds of the outlets and groups. This user is not allowed to change any settings or perform actions.

l

Read/Write: The remote group can access the Web interface, view the measures, and is allowed to change settings.



System

6.

To configure an e-mail address for this account, click the link of the e-mail address corresponding to this

user. See “Configure the E-mail Notification Settings” for more information.

7.

Click Save.

8.

To enable an e-mail address for this account, click the link on the e-mail address under the e-mail Address column.

NOTE

The Web interface will not be available as follows: l during firmware upgrades using the Upgrade network management card button l during a communications module restart using the Restart network management card button l during restoration to factory defaults using the Restore factory to default settings button

Set General System Settings

NOTE

Refresh the Web pages (press F5) to see changes to the general system settings.

1.


2.

Under Settings, select System. The System Settings page displays.

3.

In the General panel, type the Device Administrator Contact Name and the Device location in the text boxes.

4.

To change the language, select a language from the drop down list (see Figure 59).

Figure 59. Change Language on System Settings Page

5.

Select °C or °F in the Temperature drop-down list to change the temperature scale (Celsius or Fahrenheit unit of measurement).

6.

Click Save.



Enable/Disable Firmware Upgrade

1.


2.


3.

In the PDU Network Management Card panel, choose whether the firmware upgrade functionality can be used: l

Enabled: Check the check box to use the firmware upgrade functionality (default).

l

Disabled: Uncheck the check box to disable the firmware upgrade functionality.

4.

To save your changes, click Yes in response to the message prompt.

Configure PDU Network Management Card Data

1.


2.


3.

In the PDU Network Management Card Configuration panel, choose whether the IP setting and/or Daisy

Chain settings should remain unchanged after a default factory reset of the eNMC module.

l

Enabled: Check the check box beside the Keep IP parameters when “Restore Factory Default

Settings” to retain IP settings at their current values after restoration. Check the check box beside the

Keep Daisy Chain parameters when “Restore Factory Default Settings” to retain IP settings at their current values after restoration.

l

Disabled: Uncheck the check box to reset IP settings (or Daisy Chain settings) to default values

(default).

4.

To select and store an eNMC module configuration file to be used during an upgrade, use Browse to review and select the configuration file.

NOTE

When uploading a file, you cannot write the file path in the text field. You must select the file from the file explorer window that displays when you click Browse.

5.

Click either Upload or Download Configuration and a message is provided to tell you if the file uploaded successfully or failed to upload:

Upload: Gets the list of the PDU XML parameters from a file selected by the browser and sends it to the

PDU.When the upload completes, a pop-up confirmation message displays:

The file has been successfully uploaded.

You must reboot your Network Management Card for changes to take effect.

Note: This will NOT restart the PDU or change the power status of the outlets.

NOTE

Changes to network parameters require a restart, but all other setting changes will take effect immediately. l

Download Configuration: Stores a list of the PDU XML parameters in a file selected by the browser.

6.

To restore the eNMC module to factory defaults, click Restore Factory to default settings. A pop-up confirmation message displays:

Are you sure you want to restore the factory default settings of the Network

Management Card?




.

Perform Firmware Upgrade

NOTE

A firmware upgrade can only be performed by a SuperUser. This upgrades the firmware and the Web page. The Web interface will not be available during the upgrade.

1.


2.


3.

In the Network Management Card panel, ensure the firmware upgrade functionality is enabled and that the upgrade file has been downloaded.

4.

To upgrade the communications module, click Upgrade network management card. The upgrade is launched immediately

.

5.

Click Restart network management card.

6.

When the upload of the image file completes, the following message displays:

Your file was correctly uploaded.

Please wait about three minutes while the image writes to your flash device, then click the browser refresh button.

Click OK to restart the card and begin the upgrade of the firmware.

Configure the PDU

1.


2.


3.

Ensure that the Device Administrator Contact Name and the Device location have been typed in the text boxes.

4.

To select and store a PDU configuration file to be used during an upgrade, use Browse to review and select the configuration file.

NOTE


5.

Click either Upload or Download Configuration and a message is provided to tell you if the file uploaded successfully or failed to upload: l

Upload: Gets the list of the PDU XML parameters from a file selected by the browser and sends it to the PDU.

l

Download Configuration: Stores a list of the PDU XML parameters in a file selected by the browser.

NOTE

The file to upload must be a file compatible with the hardware of the PDU. If not, the upload does not process due to an incompatibility error.

NOTE

You do not need to restart the card after a successful upload.



Date & Time

Manual Configuration of the Date and Time

1.


2.

Under Settings, select Date & Time. The Date & Time page displays.

3.

In the Global Settings panel, choose the date format from the drop-down list.

4.

Click Save.

5.

Click the Set manually radio button.

6.

Type the date according to the format defined by Date Format, or select the date using the date picker.

7.

Type the time or select a time from the drop-down list. The time format is hh:mm:ss, where hh = hours,

mm = minutes, ss = second.

8.

Click Save.

NOTE

Changing the date to a future date and then reverting the date to the current date may affect the order of the display in the logs.

Automatic Configuration of the Date and Time

1.


2.

Under Settings, select Date & Time. The Date & Time page displays.

3.

In the Global Settings panel, choose the date format.

4.

Click Save.

5.

In the Global Settings panel, click the Synchronize with NTP Server radio button

6.

Type the Time Server IPv4 / IPv6 address or host name.

7.

Choose the time zone from the drop-down list.

8.

If desired, check the Daylight Saving Time option.

9.

Click Save.

NOTE

The eNMC module retrieves the date and time from the configured NTP server every hour.

TCP/IP

NOTE

The Web interface will not be available during a communications module restart using the Restart network management card button.



Configure the Ethernet Link Speed and Duplex Mode

NOTE

By default, the Ethernet link speed and duplex mode is configured on

“auto-negotiation” which means the eNMC module adapts its Ethernet speed and duplex mode to the network on which it is connected. However, it is possible to force the following modes: l l l l l

Auto-negotiation

100 Mbps Full Duplex

100 Mbps Half Duplex

10 Mbps Full Duplex

10 Mbps Half Duplex

1.


2.

Under Network, select TCP/IP. The TCP/IP page displays.

3.

In the Ethernet panel, choose one of the following link speed and duplex modes from the drop-down list: l

Auto-negotiation l

100 Mbps Full Duplex l

10 Mbps Half Duplex l

10 Mbps Full Duplex l

10 Mbps Half Duplex

4.

Click Save.

5.

Open the System page. In the Network Management Card panel, click Restart network management

card to restart the eNMC module. A pop-up confirmation message displays:

Are you sure you want to restart the Network Management Card?


Configure the IPv4 Settings

1.


2.


3.

In the IPv4 panel, select the manner by which IPv4 settings are configured from the BootP/DHCP drop-down list: l

Enabled. The IPv4 settings are configured by the DHCP server. If DHCP is enabled, go to Step 5.

l

Disabled. The IPv4 settings are manually configured by the user. If DHCP is disabled, perform the following:

- Type the IPv4 address.

- Type the IPv4 subnet mask.

- Type the IPv4 address of the gateway (if any).

- Type the MA PDU host name (used for DNS resolution).

- Type the MA PDU domain name (used for DNS resolution)

4.

Click Save.



5.

Open the System page. In the Network Management Card panel, click Restart network management




Configure the IPv6 Settings

NOTE

By default, the IPv6 interface is disabled. You can enable it from the Web interface or the Serial interface.

1.


2.


3.

In the IPv6 panel, enable the IPv6 interface by checking the IPv6 Enabled check box.

4.

Select one of the following configuration methods for IPv6 settings l

For manual configuration, uncheck the IPv6 Address Auto Configuration Enabled check box. Continue

to Step 5.

l

For auto configuration, check the IPv6 Address Auto Configuration Enabled check box. Continue to

Step 10.

NOTE 1

For manual configuration, provide the IPv6 global address with its prefix length and the IPv6 address of the gateway (if any).

NOTE 2

For auto-configuration, the global IPv6 addresses and prefix lengths are automatically configured by the network (an IPv6 router is required). The gateway

IPv6 address is defined by the user.

NOTE 3

Regardless of the configuration you choose, the local IPv6 address is auto-generated by the eNMC module.

5.

Type the local IPv6 address.

6.

Type the prefix length for the global IPv6 address.

7.

Type the IPv6 gateway address (if any).

8.

Type the second IPv6 address and prefix.

9.

Click Save.

10. Open the System page. In the Network Management Card panel, click Restart network management




Configure the DNS

When the IPv4 address is automatically obtained by DHCP, the DNS server addresses (primary and secondary) are provided by the DHCP server.

You can define DNS IPv4/IPv6 addresses from the Web and Serial interfaces. However, this configuration is overwritten when the eNMC module restarts and the IPv4 address is obtained from a DHCP server that provides DNS addresses.

1.


2.




SNMP

3.

In the DNS panel, type the primary DNS server’s IPv4 or IPv6 address.

4.

Type the secondary DNS server’s IPv4 or IPv6 address (if any).

5.

Click Save.

Configure the SMTP

1.


2.

Under Network, select TCP/IP. The TCP/IP page displays

3.

In the SMTP panel, type the SMTP server IPv4 / IPv6 address or host name.

4.

If not already provided, type the SMTP port.

5.

If your SMTP server requires authentication, perform the following: l

Check the SMTP Server Authentication check box.

l

Type the login.

l

Type the password.

l

If not already provided, type the sender address.

6.

Click Save.

Enable/Disable the SNMP Agent

1.


2.

Under Network, select SNMP. The SNMP Settings page displays.

3.

Choose one of the following SNMP versions: l

Disabled: the agent is disabled; the MIB cannot be read and no traps are sent. l

SNMPv1: only SNMPv1 users and SNMPv1 traps are supported.

l

SNMPv3: only SNMPv3 users and SNMPv3 traps are supported.

l

SNMPv1 & v3: both SNMPv1 and SNMPv3 users and traps are supported.

4.

Type the SNMP Port number and the SNMP Trap Port number in the entry boxes.

5.

Click Save.

Define SNMPv1 Users

1.


2.


3.

Ensure that SNMPv1 is selected in the SNMP Version field.

4.

In the SNMP V1 panel, in the Community column, click the SNMPv1 user to configure. The Community


5.

Choose one of the following access rights for the selected SNMPv1 user: l


l

Read-Only: the SNMPv1 user can only get the MIB objects.

l

Read-Write: the SNMPv1 user can get and set the MIB objects.

6.

Click Save. Otherwise, click Cancel to return to the SNMP Settings page.



Energy Wise

Define SNMPv3 User-based Security Model Users

1.


2.


3.

Ensure that SNMPv1 is selected in In the SNMP Version field.

4.

In the SNMP V3 panel, in the Users column, click the SNMPv3 user to configure.The SNMP User Settings dialog displays.

5.

Choose one of the following access rights for the SNMPv3 user: l

No Access: the SNMPv3 user is disabled with no access to the MIB objects.

l

Read-Only: the SNMPv3 user can only get the MIB objects.

l

Read-Write: the SNMPv3 user can get and set the MIB objects.

6.

Choose one of the following security levels to be applied to the SNMPv3 user: l

Not Set: the SNMPv3 user is not configured and therefore disabled.

l

Auth Priv: an authentication password and a privacy key are required to access the MIB objects.

l

Auth No Priv: an authentication password but no privacy key are required to access the MIB objects.

l

No Auth No Priv: no authentication password or privacy key are required to access the MIB objects.

7.

Type the authentication password (if required by security level), with 8 to 24 characters allowed.

8.

Type the privacy key (if required by security level), with 8 to 24 characters allowed.

9.

Click Save. Otherwise, click Cancel to return to the SNMP Settings page.

Access PDU MIB Objects (Privileged Access Only)

1.


2.


3.

Click Link to the PDU MIB.

Enable Energy Wise

1.


2.

Under Network, select Energy Wise. The Energy Wise page displays.

3.

In the Configuration panel, ensure that the Enable check box is checked and that the associated SDK

Version number displays. (The SDK version is not editable.)

4.

Type the Domain name (maximum 63 characters).

5.

For Security, select Enabled or Disabled.

6.

For Secret, type the secret key (maximum 63 characters).

7.

For Threshold Level, type a threshold number (minimum value 0, maximum value 10).

8.

For the Remote Port and Listen Port value, type a port number (minimum value 1, maximum value 65535).

9.

Click Save.



Security

Disable Energy Wise

1.


2.


3.

In the Configuration panel, ensure that the Disabled check box is checked. (When Disable is selected, all other fields in the Configuration panel are also disabled.)

4.

Click Save.

Start/Stop Energy Wise Commands

1.


2.


3.

The current Energy Wise state value displays in the Status field. Valid states are: l

Unknown l

Not Initialized l

Stopped l

Stopping l

Starting l

Started l

Down l

Initializing l

Up l

Active l

Requested Shutdown

4.

For Command, select one of the following from the drop-down list: l

Start l

Graceful Stop l

Off-State Cache Stop l

Restart

5.

Click Save.

Enable/Disable SSL Encryption

1.


2.

Under Network and Security, select Global. The Security page displays.

3.

In the Ports Settings panel, ensure that the HTTP Enable check box is checked and that the associated

HTTP Port number displays.

4.

Check the Force SSL check box to enable SSL encryption, or uncheck the box to disable it. If enabled, the

HTTPS Port entry box is active. Type the port number.

5.

Click Save.



6.

Open the System submenu in the Settings menu. In the Network Management Card panel, click Restart

network management card to restart the eNMC module.

NOTE

With SSL encryption, the Web interface is accessible from https://<IPv4 address> and / or https://[IPv6 address] according to the IP configuration.

NOTE

When Force SSL is selected, the Web page is only available through HTTPS. If you enter the IP address through HTTP, it will be automatically redirected to HTTPS and you will receive the following message and a new URL link:

The Network Management Card is protected by SSL encryption.

Please use the following address(es) to connect to the Network

Management Card. xxx.xxx.xxx.xxx

Enable/Disable the Telnet Interface

NOTE

Selecting a console type on the Security page makes the corresponding port entry box active.

Not selecting a console type makes the corresponding port entry box inactive and grayed-out.

1.


2.


3.

In the Ports Settings panel, select Telnet from the Console drop-down list to enable the Telnet interface, or select Disabled to disable it.

4.

If enabled, the Telnet Port entry box is active. Type the port number.

5.

Click Save.

6.



Enable/Disable the SSH Interface

1.


2.


3.

In the Ports Settings panel, select SSH from the Console drop-down list to enable the SSH interface, or select Disabled to disable it.

4.

If enabled, the SSH Port entry box is active. Type the port number.

5.

Click Save.

6.



Enable/Disable FTP

1.


2.


3.

In the Ports Settings panel, check the FTP Enable check box to enable FTP, or uncheck the box to disable it.

4.

Click Save.



5.



Set Authentication Mode

1.


2.


3.

In the Authentication Mode panel, select a value from the External Authentication drop-down list: l

None: This disables external authentication. The Preference Order field is automatically set to the Local

First, then External value.

l

Radius: This enables RADIUS. If LDAP or RADIUS are enabled, you must set a preference order in the

Preference Order drop-down list:

- External First, then Local

- Local First, then External

- External only

l

LDAP: This enables LDAP. If enabled, you must set a preference order in the Preference Order drop-down list:

- External First, then Local

- Local First, then External

- External only

4.

Click Save.

Set LDAP Search Configuration

NOTE

Each selection combination requires a different set of entries. Only applicable fields are active. Fields that do not apply to your selection are inactive. l

Active fields are white and the inactive fields are blue shaded. l

When you click your cursor in inactive fields, nothing happens.

l

You can type in active fields.

1.


2.

Under Network and Security, select LDAP. The LDAP page displays.



3.

Select the LDAP Server Type, User Search Bind, and Authorization Mode values from the drop-down list: l

LDAP Server Type: Allows you to select a configuration.

- Active Directory: Allows to configure a typical AD configuration. Some fields are read-only (User

Object and User Attribute are disabled).

- Other: All fields are editable.

l

User Search Bind: Defines if a special user for the LDAP searches must be used.

- Anonymous Search: Search bind uses an anonymous way (Search User and Password are disabled)

- User Bind Search: Uses an LDAP user. l

Search User: DN (if Bind Type = simple) or the username (if Bind Type = MD5) of the LDAP user allowed to search in the LDAP dictionary.

l

Password: Password of the Search User.

l

User Base DN: Entry of the LDAP dictionary where to start the user search.

l

User Object: Object class of the LDAP users.

l

User Attribute: LDAP attribute of the user object which is used to store the login identifier.

l

Authorization Mode: Choose authorization by user attribute or by group.

- By User attribute: Stores the group name in the user attribute (Group Name Attribute).

- By Group: Stores the group name in the group LDAP object (UPS Group Base DN).

l

PDU Group Base DN: LDAP dictionary entry from which the group search starts.

l

Group Name Attribute: LDAP attribute that stores the group name.

l

User Name Attribute: LDAP attribute that stores the users names linked to this group.

4.

The resulting required field entries are active and highlighted. Type the associated values in the active entry boxes.

5.

Click Save.

Authenticate LDAP Remote User

To test the login and password and authenticate an LDAP remote user:

1.


2.


3.

In the LDAP Authentication Test panel, select the following: l

Login: The login of the remote user.

l

Password: The password of the remote user.

4.

Click Test. An authentication test is launched and a message displays on the LDAP Authentication Test panel to indicate if the authentication was successful or unsuccessful.

Table 10 provides authentication error messages and descriptions of possible causes.



Table 10. Authentication Error Messages and Possible Causes

Error Message Description

User Not Found

Search Bind Failed

Search User Invalid Credential

l

Bad value in the User Object field. The usual value for AD is user. l

Bad value in the User Attribute field. The usual value for AD is sAMAccountName.

l

Although the DN set in the User Base DN field exists in the LDAP Server, the login input is not found under the LDAP tree of this object.

l

The login input does not exist in the LDAP Server.

l

The User Search Bind field is set to Anonymous, but this mode is not supported by the LDAP

Server.

l

The User Search Bind field is set to User Bind Search, but the Password is empty while it is required by the LDAP server.

1. Bad value in the Password field of the Search User.

2. Bad value in the Search User field: l

In SASL MD5 mode:

A DN is used in the Search User field instead of a name.

The DNS does not provide the reverse resolution of the LDAP server IP. l

In simple mode:

Usually, a DN must be used in the Search User field.

l

Regardless of the mode:

The Search User input did not match any existing object in the LDAP database.

Root for User Base DN is incorrect

l

The root part of the User Base DN field is incorrect.

Relative Distinguished Name for

User Base DN is incorrect

l

The root part of the User Base DN field is correct, but the remaining part does not exist in the

LDAP server.

User Invalid Credential

LDAP Search Group Not Found

l l

The login password is incorrect.

No remote group has been set in the Access Accounts page.

l

No relationship has been found between the PDU remote groups and the LDAP groups.

l

Although the DN set in the PDU Group Base DN field exists in the LDAP Server, no PDU remote groups have been found under the LDAP tree of this object.

l

Bad value in the Group Name Attribute field (configuration Other).

l

Bad value in the User Name Attribute field (configuration Other).

l

The root part of the PDU Group Base DN field is incorrect.

Root for Group Base DN is incorrect

Relative Distinguished Name for

Group Base DN is incorrect

LDAP Server Unavailable

l l

The root part of the PDU Group Base DN field is correct, but the remaining part does not exist in the LDAP server.

Bad LDAP server IP address.

l

Bad LDAP server port.

l

Bad LDAP server name.

l

In case of LDAPS/Start TLS Encryption method:

The LDAP server is not configured to use SSL.

The PDU Authority Certificate is required by the LDAP server but it has not been added in the certificate store of the LDAP server as Trusted Certification Authority.

If the Activate AC Certificate field of the LDAP Server Global Parameters panel is checked, the

LDAP Server Authority Certificate uploaded in the PDU is not the correct.



Set LDAP Server Global Parameters

1.


2.


3.

In the LDAP Server Global Parameters panel, select the following: l

Encryption Method: The Encryption method defines if an SSL connection is used between the PDU and the LDAP server when the LDAP requests are sent during the PDU user authentication process.

From the drop-down list, select one of the following:

- None: (No SSL connection) The data is sent without encryption. The standard port number is 389

(the port for no encryption). It can be set or modified from the LDAP Server Settings dialog.

- LDAPS: (With SSL Connection) This selection uses an LDAP-over-SSL connection. The standard port number is 636. It can be set or modified from the LDAP Server Settings dialog

- Start TLS: (With SSL Connection) Use the “start TLS” extension (RFC 2830). The standard port number is 389 (the same port that for no encryption). It can be set or modify from the LDAP Server

Settings dialog.

l

Bind Type: The bind operation uses the LDAP user credentials to identify the LDAP authentication connection between the PDU and the LDAP server. From the drop-down list, select one of the following:

- Simple: The user credentials are sent without encryption. However, if an SSL connection is used, the credentials are encapsulated in an SSL-encrypted connection.

- SASL Digest MD5: Using MD5, a hash algorithm is used to encrypt the user credentials.

4.

To upload your AC Certificate, select Browse. Highlight the selected file and click Open.

!

IMPORTANT

The AC Certificate is the AC Certificate of the LDAP server, not the AC Certificate of the PDU. The certificate format is a Base64 encoded DER certificate, enclosed between the "-----BEGIN

CERTIFICATE-----" and "-----END CERTIFICATE-----" tag.In order to configure your LDAP server for

SSL, you need the AC certificate of the PDU certificate.

NOTE


5.

Click Upload.

6.

Click Save.

Modify LDAP Server Settings

1.


2.


3.

In the LDAP Server panel, click a linked host name. The LDAP Server Settings dialog displays.

4.

In the Enable Server drop-down list, select Enable or Disable to enable or disable the selected LDAP server or servers.

5.

If enabled, you can choose to change the server name, the port number, and the number of seconds to time out in the Server, Port, and Time Out (sec) entry boxes.

6.

Click Save. Otherwise, click Cancel to return to the LDAP page.



Add RADIUS Server

Authorization configuration must be done in the radius server to add the MA PDU remote group defined in the

Remote Group Access MA PDU setting.

The authorization is based on the information sent by the server through the following RADIUS attribute: l

Vendor Specific ID: 534 l

Vendor Specific Attribute ID: 29, format string

The authorization strings sent by the server from the vendor-specific attributes (VSA) are compared with the remote groups configured in the MA PDU. If a remote group is found, the profile user linked to the remote group is set to the remote user (in case of authentication success). If no group is found, the access is rejected by the MA PDU.

This attribute must be added in the RADIUS server configuration and must be sent for each remote user allowed to access to the MA PDU.

To add a RADIUS server:

1.


2.

Under Network and Security, select RADIUS. The RADIUS page displays.

3.

In the RADIUS Server panel, select the following: l

Authentication Protocol: Select an authentication method from the drop down list, either Password

Authentication Protocol (PAP) or Challenge-Handshake Authentication Protocol (CHAP).

4.

Check the Add check box.

5.

In the RADIUS Settings panel, select the following: l

Primary or Secondary Server: Identify the server by selecting Primary Server or Secondary Server.

l

Enable Server: From the drop-down list, select Enable to enable the server or Disable to disable the server.

l

RADIUS Server: Enter the IPv4 address, IPv6 address, or the host name of the RADIUS server.

l

Secret: Shared secret (case sensitive).

l

NAS IP Address: The NAS field allows you to select an IP address from the IP addresses of the card.

l

UDP Port: The User Datagram Port (UDP) number (standard: 1812).

l

Time Out (sec): Type the number of seconds to wait for a response from the authentication server before trying to reconnect.

l

Retry Number: Type the number of times to try to reconnect to the authentication server before reporting that the connection failed for one authentication attempt.

6.

When you finish selecting parameters for the RADIUS server, click Save or Cancel.

Edit Parameters for a RADIUS Server

1.


2.

Under Network and Security, select RADIUS. The Security - RADIUS page displays.

3.

In the RADIUS Server panel Name column, click the name of the RADIUS server you want to edit.

4.

The RADIUS Settings dialog displays. Change the parameters as needed.

5.

When you finish modifying parameters for the RADIUS server, click Save or Cancel.


Chapter 8 Serial Interface Operation

This section describes the CLI (Command Line Interface) commands used to remotely configure and monitor the HP Managed PDU through the serial interface connection or network connection between the HP HP MA

(Managed) PDU (Power Distribution Unit) and a laptop or workstation.

Access to a CLI is provided through a terminal emulation program, such as HyperTerminal, Telnet, or SSH.

For example, open a saved HyperTerminal connection as follows:

1.

Select Start > All Programs > Accessories > Communications > HyperTerminal > saved connection

name.ht.

2.

On the New Connection dialog, select File > Open. The Open dialog displays. In the File Name window, select the saved connection file you intend to use. Click Open.

3.

The HyperTerminal session window opens for the connection you selected. Press any key to display the banner. To open an authentication session, type your user name to log in.

NOTE

See “Network Communication Configuration” on page 28 for more information creating a serial connection and configuring the network.

Supported Commands

The MA PDU CLI command set for managing and monitoring the MA PDU includes the following commands: l

?

l info l quit l get l set l pdu

NOTE

Commands are case-sensitive. Parameters and attributes are not. Command variables are represented in command input syntax surrounded by angle braces (<

>). Optional parameters are represented in command input syntax surrounded by straight brackets ([ ]). For data of type array, the 'x' character as index of array in command input syntax means all indexes.

NOTE

You must be logged into the MA PDU before commands can be sent.


Serial Interface Operation

? command

Use this command to list all available PDU CLI commands or receive detailed help on specified commands

Usage

PDU#0>?

PDU#0><command> ?

where:

<command> = info, get, set, pdu, quit

List all available PDU CLI commands

PDU#0>?

Example

PDU#0>?

Usage: ? info get set pdu quit

PDU#0>

List detailed help on a specific PDU CLI command

PDU#0><command> ?

Example 1

PDU#0>set ?

Usage: change the device data defined by its’ name followed by the new value set [name] [value]

PDU#0>

Example 2

PDU#0>pdu ?

Usage: select the strapping pdu unit to focus on pdu [number]

PDU#0



info command

Use this command to display the device data for objects.

Usage

PDU#0>info <object>

where:

<object> = name of a simple object, an object of type array or a family of objects.

Example 1

pdu#0>info System.Network.DHCP

Name

System.Network.DHCP

Unit RO/RW Type

RW 0: Disabled

1: Enabled

Example 2

pdu#0>info PDU.*

Name

PDU.DaisyChain[x].ChangedStatus.Communication

Lost

Unit sec

PDU.DaisyChain[x].iName sec

.

RO/RW Type

RO

RO

Integer:0..4294967295(136 years)

String[15]

.

.

PDU.DaisyChain[x].PresentStatus.Communication

Lost sec RO 0: Normal

1: Alarm

Example 3

pdu#0>info System.*

Name Unit RO/RW Type

System.NetworkManagementSystem.Count RO Integer:0..65535

System.NetworkManagementSystem[x].HostName RW

System.NetworkManagementSystem[x].TrapCommunity RW

.

String[63]

String[24]

.

.

System.NetworkManagementSystem[x].TrapSnmpVersion RW

1: SNMP V1

2: SNMP V3



Example 4

pdu#0>info Environment.*

Name Unit RO/RW Type

Environment.ChangedStatus.CommunicationLost sec RO Integer:0..4294967295(136 years)

Environment.ChangedStatus.OverHumidity sec

Environment.ChangedStatus.OverTemperature sec

RO

RO

Environment.Humidity RO

Environment.Input[1].ChangedStatus.Alarm sec RO

Float:0..6553.5

String[31] Environment.Input[1].iName RW

.

.

.

Environment.Input[1].PresentStatus.Alarm RO

1: Alarm


quit command

Use this command to log out and exit the serial or network interface for the PDU.

Usage

PDU#0>quit

Log out of the CLI

PDU#0>quit

Example with serial interface

PDU#0>quit

Session closed

Example with network interface

PDU#0>quit

Connection to host lost.




get command

Use this command to view the value of an object or a family of objects that belong to the HID database or a card parameter.

Usage

PDU#0>get <object>

where:

<object> = a simple object, an object of type array or a family of objects.

Get a single value

PDU#0>get <path>.<name>

Example

PDU#0>get System.Network.DHCP

1

PDU#0>

Get the size of an array

PDU#0>get <path>.Count

Example

pdu#0>get System.NetworkManagementSystem.Count

8 pdu#0>

Get a single value of an array

PDU#0>get <path[i]>.<name>

where:

[i] = the index in the array, from 1 to n. The value of n depends of the HID object and is obtained with a get command

Example

pdu#0>get System.NetworkManagementSystem[1].TrapCommunity

public pdu#0>

Get all values of an array

PDU#0>get <path[x]>.<name>

NOTE

Values are separated by the pipe character ( | ).

Example

pdu#0>get System.User[x].SecurityRight

0|0|0|0|0|0|0|0 pdu#0>


Get all values of a family

PDU#0>get <short path>.*

where

<short path> = incomplete path name. A node must be complete.

Example 1

pdu#0>get System.DaisyChain.*

System.DaisyChain.DeviceId

1

System.DaisyChain.Position

0

System.DaisyChain.Status

0

System.DaisyChain.Count

1 pdu#0>

Example 2

pdu#0>get System.*

System.NetworkManagementSystem.Count

8

System.NetworkManagementSystem[x].HostName

../..

pdu#0>




set command

Use this command to change the value of an object that belongs to the HID database or a card parameter.

NOTE

Some data cannot be modified without appropriate user access rights.

Usage

PDU#0>set <object> <value>

where:

<object> = a simple object or an object of type array.

<value> = a value or a list of values separate with the pipe character ( | ). For a value of type string, the space character ' ' is taken into account.

Set a single value

PDU#0>set <path>.<name> <value>

Example 1

pdu#0>set System.Network.DHCP 1

1 pdu#0>

Example 2

pdu#0>set System.Display.LcdRotation 1

1 pdu#0>

where:

<0> = Rotation 0 Degree (0U)




Set value of an array

PDU#0>set <path[i]>.<name> <value>

where:

[i] = the index in the array, from 1 to n. The value of n depends of the HID object and is obtained with a get command

Example

pdu#0>set System.Network.SNMP.V3.User[1].Name User 1

User 1 pdu#0>



set all values of array

PDU#0>set <path[x]>.<name> <value 1>[|<value 2>]../..[|<value n>]

NOTE

Values are separated by the pipe character ( | ).

Example

pdu#0>set System.Network.SNMP.V3.User[x].Name User 1|User 2|User 3|User 4

User 1|User 2|User 3|User 4 pdu#0>


pdu command

Use this command to access different PDUs on the daisy chain.

Usage

PDU#0>pdu <value>

where:

<value> = 0 for the host; 1, 2, or 3 for the device

Example

pdu#0>pdu 1 pdu#1>




Error Messages

The following errors could display:

The command is unknown.

This error displays when an invalid command is entered. Valid commands are ?, info, get, set, pdu, and quit.

The parameter in the command is unknown.

This error displays when a parameter you entered in the command is not recognized.

The parameter in the command is out of limits.

This error displays in the following circumstances:

- The set command refers to a data name but does not have the second parameter.

- The set command refers to a value that does not match with the data.

The command is not valid for this object.

This error displays when the set command refers to an object that cannot be set after the system preforms a coherence check with other data.

The user has insufficient rights.

This error displays when:

- The set command contains read-only data.

- The user has insufficient rights to modify the data.

The PDU1 is not available.

This error displays when the indicated PDU is unreachable.



XML Object Tables

This section includes tables that define PDU CLI objects (Table 11) and System CLI Objects (Table 12 on page 111).

Table 11. PDU CLI Objects

XML Object Name

Environment.ChangedStatus.CommunicationLost

Type

Timestamp

Environment.ChangedStatus.OverHumidity

Environment.ChangedStatus.OverTemperature

Environment.Humidity

Environment.Input[1].ChangedStatus.Alarm

Environment.Input[1].iName

Environment.Input[1].PresentStatus.Alarm

Environment.Input[1].PresentStatus.State

Environment.Input[1].State[0].Level


Environment.Input[2].ChangedStatus.Alarm

Environment.Input[2].iName

Environment.Input[2].PresentStatus.Alarm

Environment.Input[2].PresentStatus.State

Timestamp

Timestamp

Measure

Timestamp

String[31]

AlarmL1

Measure

Parameter

Parameter

Timestamp

String[31]

AlarmL1

Measure

Description

Timestamp of last changing state of the alarm that has the same name in the collection PresentStatus.



Measured Humidity on environmental monitoring probe.

0 when no probe is connected or when the probe does not have a humidity sensor.


Contact 1 friendly name

Dry Contact alarm. Set according to the dry contact State and the parameter State[0] or [1].Level

0: Alarm not active

1: Alarm active

Ex: State=0 AND State[0].Level=3 then Alarm=1

Dry Contact state

0: Open

1: Close

Dry contact Config

1: Open makes just informational 0 into State.

2: Open makes Warning trap

3: Open makes Alarm trap

Dry contact Config

1: Close makes just informational 0 into State.

2: Close makes Warning trap

3: Close makes Alarm trap


Contact 2 friendly name

Dry Contact alarm. Set according to the dry contact State and the parameter State[0] or [1].Level

0: Alarm not active

1: Alarm active

Ex: State=0 AND State[0].Level=3 then Alarm=1

Dry Contact state

0: Open

1: Close

-

-

-

-

-

-

-

s

Unit Access

RO s s d% RO s s

RO

RO

RO

RW

RO

RO

RW

RW

RO

RW

RO

RO



Table 11. PDU CLI Objects (Continued)

XML Object Name



Environment.OverHumidity[1].Threshold




Environment.OverTemperature[1].Threshold




Environment.PresentStatus.CommunicationLost

Environment.PresentStatus.OverHumidity

Environment.PresentStatus.OverTemperature

Environment.PresentStatus.Present

Environment.Temperature

PDU.DaisyChain[x].ChangedStatus.CommunicationLost

PDU.DaisyChain[x].iName

PDU.DaisyChain[x].PresentStatus.CommunicationLost

PDU.Gang.Count

PDU.Gang[x].ActivePower

Type

Parameter

Parameter

Parameter

Parameter

Parameter

Parameter

Parameter

Parameter

Parameter

Parameter

AlarmL1

AlarmL1

AlarmL1

Measure

Measure

Timestamp

String[15]

AlarmL1

Constant

Measure

Description

Dry contact Config

1: Open makes just informational 0 into State.

2: Open makes Warning trap.

3: Open makes Alarm trap.

Dry contact Config

1: Close makes just informational 0 into State.

2: Close makes Warning trap.

3: Close makes Alarm trap.

-

-

Unit Access

RW

RW

0: OK

1: Communication failure with the sensor probe or probe not present.

0: No threshold triggered

1: Warning low threshold triggered

2: Critical low threshold triggered

3: Warning high threshold triggered

4: Critical high threshold triggered






0: Probe not connected

1: Probe connected

Measured Temperature on environmental monitoring probe.

It is 0 when no probe is connected.

Timestamp of the last changing state of the alarm with the same name in the collection PresentStatus.

Daisy-chain friendly name.

0: OK

1: Communication with daisy chained device has failed.

Number of factory groups in the PDU.

Active Power provided by the breaker/section. For a double pole breaker, the apparent power for the two poles is combined.

-

-

-

-

d% RW d% RW d% RW d% RW

d°K RW d°K RW d°K RW d°K RW

RO d°K RO s

RO

RO

RO

RO

RO

RO

RO dW RO



XML Object Name

PDU.Gang[x].ApparentPower

PDU.Gang[x].ChangedStatus.OverCurrent

PDU.Gang[x].ChangedStatus.OverVoltage

PDU.Gang[x].ConfigCurrent

PDU.Gang[x].Current

PDU.Gang[x].GangID

PDU.Gang[x].iGang

PDU.Gang[x].iName

PDU.Gang[x].InputID

PDU.Gang[x].OverCurrent[1].Threshold



PDU.Gang[x].OverVoltage[1].Threshold




PDU.Gang[x].PeakFactor

PDU.Gang[x].PercentLoad

PDU.Gang[x].PhaseID

PDU.Gang[x].Pole[1].ActivePower

PDU.Gang[x].Pole[1].ApparentPower

PDU.Gang[x].Pole[1].Current

PDU.Gang[x].Pole[1].PeakFactor

PDU.Gang[x].Pole[1].PhaseID

PDU.Gang[x].Pole[1].PowerFactor

PDU.Gang[x].Pole[1].ReactivePower

PDU.Gang[x].Pole[1].Statistic[5].Energy

PDU.Gang[x].Pole[1].Voltage

PDU.Gang[x].Pole[2].ActivePower


Type

Measure

Description

Apparent Power provided by the breaker/section. For a double pole breaker, the apparent power for the two poles is combined.

Timestamp

Timestamp

Constant

Measure

Constant

String[15]

String[31]

Constant

Nominal Amps: 10A, 16A, 20A, ..

This is useful for both breaker and outlet section.

Current provided by the breaker/section. For a double pole breaker, it is calculated as the max of the two poles current.

Breaker ID = x(1,2,..)

Breaker/section silk-screened name.

Example: 'A' or 'B' ….

Breaker/section friendly name.

Identify which Input is powering the group. This is useful when the PDI is dual Input.

Parameter

Parameter

Parameter

Parameter

Parameter

Parameter

Parameter

Measure

Measure

Constant

Threshold

Threshold

Threshold

Threshold

Crest factor of the current provided by the breaker/section.

A double pole breaker is calculated as the max of the two poles crest factor.

Percent load consumed by the breaker/section. It is the ratio: current consumed / the nominal current.

Phase number that is connected to the breaker/section: 1,

2, or 3.

A double pole breaker is ij.

Ex: 12 if the 2 phases are L1 and L2.

HideMeasure Active Power provided by the pole.

HideMeasure Apparent Power provided by the pole.

HideMeasure Current provided by the pole.

HideMeasure Crest factor of the current provided by the pole.

Constant Phase number that is connected to the pole: 1, 2, or 3.

HideMeasure Ratio of active power / apparent power provided by the pole of the breaker or outlet section.

HideMeasure Reactive Power provided by the pole.

-

-

-

-

-

Unit Access

dVA RO s s

RO

RO mA RO mA RO

RO

RO

RW

RO mA RW mA RW mA RW cV RW cV cV

RW

RW cV RW m% RO

% RO

RO dW RO dVA RO mA RO m% RO

RO m% RO dVA

R

RO

Wh RO HideMeasure Energy counter since last reset. As it is reset to 0, the related timestamp is updated with the current RTC value.

HideMeasure Voltage Measured on the pole.

HideMeasure Active Power provided by the pole.

cV dW

RO

RO



XML Object Name

PDU.Gang[x].Pole[2].ApparentPower

PDU.Gang[x].Pole[2].Current

PDU.Gang[x].Pole[2].PeakFactor

PDU.Gang[x].Pole[2].PhaseID

PDU.Gang[x].Pole[2].PowerFactor

PDU.Gang[x].Pole[2].ReactivePower

PDU.Gang[x].Pole[2].Statistic[5].Energy

PDU.Gang[x].Pole[2].Voltage

PDU.Gang[x].PowerFactor

PDU.Gang[x].PresentStatus.OverCurrent

PDU.Gang[x].PresentStatus.OverVoltage

PDU.Gang[x].PresentStatus.Tripped

PDU.Gang[x].ReactivePower

PDU.Gang[x].Statistic[3].Current

PDU.Gang[x].Statistic[3].ModuleReset

PDU.Gang[x].Statistic[3].Reset.Time

PDU.Gang[x].Statistic[3].Time

PDU.Gang[x].Statistic[5].Energy

PDU.Gang[x].Statistic[5].ModuleReset

PDU.Gang[x].Statistic[5].Reset.Energy


Type Description

HideMeasure Apparent Power provided by the pole.

HideMeasure Current Power provided by the pole.

HideMeasure Crest factor of the current provided by the pole.

Constant Phase number that is connected to the pole: 1, 2, or 3.

HideMeasure Ratio of active power / apparent power provided by the pole of the breaker or outlet section.

HideMeasure Reactive Power provided by the pole.

Unit

dVA

Access

RO mA RO

m% RO

RO m% RO

HideMeasure Energy counter since last reset. As it is reset to 0, the related timestamp is updated with the current RTC value.

HideMeasure Voltage Measured on the pole.

Measure

AlarmL1

Ratio of active power / apparent power provided by the breaker or outlet section.




AlarmL1






AlarmL1

Measure

Measure

Command

Measure

Measure

Measure

Command

Measure



0: Normal

1: Alarm

Reactive Power provided by the breaker/section. For a double pole breaker, the reactive power for the two poles is combined.

Current peak consumption since last reset.

As it is reset to 0, the related timestamp is updated with the current RTC value.

When a value higher than the stored value is detected, the stored valued is overwritten.

Command to Reset the stat. This command puts 0 in the max and saves the current value of Timer.

Timestamp saved when the stat reset is performed.

Timestamp saved at the moment where the current peak consumption is reset.

Energy counter since PDU startup.

For a double pole breaker, it is calculated as the accumulation of the two poles energy counter.

Command to Reset the stat, This command does not put 0 in the counter, but saves the current value of Energy timer into the data, Reset.Energy.

Energy saved when the user resets the stat.

-

-

-

-

s s dVA

R

RO

Wh RO cV RO m% RO dVA

R

RO

RO

RO

RO mA RO

RW

RO

RO

Wh RO

RW

Wh RO




XML Object Name

PDU.Gang[x].Statistic[5].Reset.Time

PDU.Gang[x].Type

PDU.Gang[x].Voltage

PDU.Input[1].ActivePower

PDU.Input[1].ApparentPower

PDU.Input[1].ChangedStatus.FrequencyOutOfRange

PDU.Input[1].Frequency

PDU.Input[1].Mode

PDU.Input[1].Phase.Count

PDU.Input[1].Phase[x].ActivePower

PDU.Input[1].Phase[x].ApparentPower

PDU.Input[1].Phase[x].ChangedStatus.OverCurrent

PDU.Input[1].Phase[x].ChangedStatus.OverVoltage

PDU.Input[1].Phase[x].Current

PDU.Input[1].Phase[x].OverCurrent[1].Threshold



PDU.Input[1].Phase[x].OverVoltage[1].Threshold




Type

Measure

Constant

Description

Timestamp saved when the user resets the stat.

Type of gang:

1 : Section of outlets (with 1 measurement)

2 : Section of outlets (with 2 measurement, 1st method of wiring CT, current is max of 2 pole measures)

3 : Section of outlets (with 2 measurement, 2nd method of wiring CT, current is sum of 2 pole measures)

4 : Breaker 1 pole

5 : Breaker 2 pole (with 1 pole measurement)

6 : Breaker 2 pole (with 2 pole measurement, 1st method of wiring CT, current is max of 2 pole measures)

7 : Breaker 2 pole (with 2 pole measurement, 2nd method(PQNA) of wiring CT, , current is sum of 2 pole measures)

8 : Section of outlets (without current measurement)

Measure

Measure

Measure

9 : Section of outlets (with current and voltage measurement)

Voltage Measured on the breaker/section.

For a double pole breaker, it is the Li to Lj voltage.

Active Power Measurement.

It is the accumulation of 1 or 3 phase measures.

Apparent Power Measurement.


Timestamp

Measure

Constant

Frequency Measurement.

Wiring Mode

0: Wye Measuring

Constant

Measure

Timestamp

Measure

Parameter

1: Delta Measuring

2: Wye Current and Delta Measuring

Number of phase managed by the Input module.

Active Power Measurement.

HideMeasure Apparent Power Measurement.

Timestamp Timestamp of last changing state of the alarm that has the same name in the collection PresentStatus.


Current Measurement.

Parameter

Parameter

Parameter

Parameter

Parameter

Parameter

s

Unit Access

RO

RO cV s

RO dW RO dVA RO

s RO dHz RO

RO

RO dW RO dVA RO s RO

RO cV cV cV cV mA RO mA RW mA RW mA RW

RW

RW

RW

RW




XML Object Name

PDU.Input[1].Phase[x].PeakFactor

PDU.Input[1].Phase[x].PercentLoad

PDU.Input[1].Phase[x].PhaseID

PDU.Input[1].Phase[x].PowerFactor

PDU.Input[1].Phase[x].PresentStatus.OverCurrent

PDU.Input[1].Phase[x].PresentStatus.OverVoltage

PDU.Input[1].Phase[x].ReactivePower

PDU.Input[1].Phase[x].Statistic[5].Energy

PDU.Input[1].Phase[x].Statistic[5].ModuleReset

PDU.Input[1].Phase[x].Statistic[5].Reset.Energy

PDU.Input[1].Phase[x].Statistic[5].Reset.Time

PDU.Input[1].Phase[x].Voltage

PDU.Input[1].PowerFactor

PDU.Input[1].PresentStatus.FrequencyOutOfRange

PDU.Input[1].ReactivePower

Type

Measure

Measure

Constant

Description

Crest factor of the current provided by the phase.

Percent load consumed on the phase. It is the ratio: current consumed / the nominal current of the PDU.

Phase ID identifier depending of the wiring:

1: Line 1 to Neutral



12: Line 1 to Line 2



HideMeasure Ratio of active power / apparent power provided by the phase.

AlarmL1

AlarmL1

Value 0 to 100 for Cos PHI = 0.00 to 1.00











HideMeasure Reactive Power Measurement.

-

-

-

Unit Access

m% RO

% RO

RO m% RO

RO

RO dVA

R

RO

Wh RO HideMeasure Energy counter since last reset. As it is reset to 0, the related timestamp is updated with the current RTC value.

Command

HideMeasure Energy counter saved at last reset. As it is reset, the related timer updated with PDU timer since 1st restart.

HideMeasure Timestamp saved at the moment when the related energy counter is reset.

Measure

Measure

Voltage Measurement.

Ratio of active power / apparent power provided by the input.

AlarmL1

Measure

Value 0 to 100 for Cos PHI = 0.00 to 1.00

0: Frequency OK

1: Frequency is out of +/- 3Hz tolerance

Reactive Power Measurement.


-

-

Wh s cV m% dVA

R

RW

RO

RO

RO

RO

RO

RO




XML Object Name

PDU.Input[1].Statistic[3].ActivePower

PDU.Input[1].Statistic[3].ModuleReset

PDU.Input[1].Statistic[3].Reset.Time

PDU.Input[1].Statistic[3].Time

PDU.Input[1].Statistic[5].Energy

PDU.Input[1].Statistic[5].ModuleReset

PDU.Input[1].Statistic[5].Reset.Energy

PDU.Input[1].Statistic[5].Reset.Time

PDU.Input[1].Type

PDU.MeasurementBoard.Gateway.Address

PDU.MeasurementBoard.Gateway.Command

PDU.MeasurementBoard.Gateway.Count

PDU.MeasurementBoard.Gateway.Register

PDU.MeasurementBoard.Gateway.Switchable

PDU.MeasurementBoard.Gateway[x].Value

Type

Measure

Command

Measure

Measure

Measure

Description

Power peak consumption since last reset.

As it is reset to 0, the related timestamp is updated with the current RTC value.

When a value higher than the stored value is detected, the stored valued is overwritten.

Command to Reset the stat. This command puts 0 in the max and saves the current value of Timer into the data

…Timer and into ...Reset.Timer.

Timestamp saved at the moment when the statistic is reset.

Timestamp saved at the moment when the statistic is reset.

Energy counter since last reset. As it is reset to 0, the related timestamp is updated with the current RTC value.

Command

It combines the energy consumed on 1 or 3 phases.

Command to Reset the stat. This command does not put 0 in the counter, but it saves the current value of Energy timer into the data ...Reset.Energy.

Energy saved at the instant the user resets the stat.

Measure

Measure Timestamp saved at the instant the user resets the stat.

Constant List types of PDU Input plugs.

HideMeasure Address of the teridian module to be accessed.

HideMeasure Write: command to the Gateway

0: None

1: Read

2: Write

Read: return the CR of last command to the Gateway:

0: Success

<> 0 , Access failed for the following reasons:

1: Command Unknown.

2: Gateway not enabled.

3: Address out of range.

4: Register out of r.

HideMeasure Number of 32 bits data to be read or write in consecutive

READ or WRITE request. 1 to 8.

HideMeasure Address of the register to be read or write.

HideMeasure 0: The gateway is disabled.

1: The gateway is enabled.

HideMeasure 1 up to 8 consecutive register values can be read or write with the gateway in one request.

NOTE: Follow these steps to read registers from the board:

1. Write 1 in Command

2. Read Command, check it is 0

3. Read the data that had been read into Value

-

-

-

-

-

Unit Access

dW RO s s s

RW

RO

RO

Wh RO

RW

-

Wh RO

-

s RO

RO

RW

RW

RW

RW

RW

RW




XML Object Name Type

PDU.MeasurementBoard[x].PresentStatus.CommunicationLost

Measure

PDU.OutletSystem.Outlet.Count

PDU.OutletSystem.Outlet[x].ConfigCurrent

PDU.OutletSystem.Outlet[x].GangID

PDU.OutletSystem.Outlet[x].iName

PDU.OutletSystem.Outlet[x].OutletID

PDU.OutletSystem.Outlet[x].PhaseID

PDU.OutletSystem.Outlet[x].PoleID

PDU.OutletSystem.Outlet[x].PresentStatus.SwitchOnOff

PDU.OutletSystem.Outlet[x].Type

PDU.PowerSummary.ChangedStatus.CommunicationLost

Constant

Constant

Constant

String[31]

Constant

Constant

Constant

Measure

Constant

Timestamp

Communication status with the acquisition card ICM &

SM:

0: Communication OK

Description

1: Communication failed.

Total Number of outlets

Nominal Amps: 10A, 15A, 16A, 20A, ..

Breaker/section index where the Outlet is connected.

It is the x of Gang[x] collection.

Outlet friendly name.

Numbering of the outlet into the breaker/section module.

1 to 56.

Phase ID that powers the outlet:

- 1, 2, 3 to identify a simple phase.

- 12, 23, 31 to identify a composed phase.

Pole ID of the breaker/section where the Outlet is connected. Two cases are:

- Section or Single pole breaker, always 0.

- Double pole breaker:

0: when powered between 2 poles

1: when powered by pole 1 voltage.

2: when powered by pole 2 voltage.

0: Outlet not powered

1: Outlet powered

Types of PDU outlets: unknown (0), iecC13 (1), iecC19 (2), uk (10), french (11), schuko (12), nema515 (20), ema51520 (21), nema520 (22), nemaL520 (23), nemaL530 (24), nema615 (25), nema620 (26), nemaL620 (27), nemaL630 (28), nemaL715 (29), rf-203P 277v (30)

Communication intra modules have failed.

-

-

-

-

-

-

-

Unit Access

RO

-

RO mA RO

RO s

RW

RO

RO

RO

RO

RO

RO




XML Object Name

PDU.PowerSummary.ConfigActivePower

PDU.PowerSummary.ConfigCurrent

PDU.PowerSummary.ConfigVoltage

PDU.PowerSummary.iManufacturer

PDU.PowerSummary.iName

PDU.PowerSummary.iPartNumber

PDU.PowerSummary.iProduct

PDU.PowerSummary.iReferenceNumber

PDU.PowerSummary.iSerialNumber

PDU.PowerSummary.iVersion

PDU.PowerSummary.PDUType

PDU.PowerSummary.PresentStatus.CommunicationLost

PDU.PowerSummary.Temperature

PDU.PowerSummary.Time

PDU.PowerSummary.Timer

Type

Constant

Constant

Constant

String[31]

String[31]

String[15]

String[63]

String[31]

String[15]

String[15]

Constant

AlarmL1

Measure

Measure

Measure

Description

PDU Nominal Active Power

PDU PDU total rating current.

PDU rating voltage.

Manufacturer Name. Example:

"HP"

Unit friendly name.

Part Number.

Product Name.

Technical Reference of firmware.

Serial Number.

F/W Version.

Feature Topology of the PDU:

0: Unknown

1: SW (Switched)

2: AM (Advanced Monitored)

3: MA (Managed)

4: MI (Monitored)

Communication intra modules have failed.

Internal Temperature.

Unix timestamp that is refreshed from the RTC.

Time elapsed since the 1st start of the device.

Table 12. System CLI Objects

XML Object Name

System.Bootloader.iVersion

System.Bootloader.Mode

System.Contact

System.DaisyChain.Count

System.DaisyChain.DeviceId

System.DaisyChain.Position

s s

RO d°K RO

RW

RO

Access right

admin superadmin admin admin admin admin

Type Description

String:15

BootMode 0: Normal

1: Upgrade

2: Passthru

3: ATE

4: Bootstrap

String:31

Integer0to65535

DaisyChainDeviceId 0: Host

1: Device 1

2: Device 2

3: Device 3

DaisyChainPosition 0: Middle

1: End

Access

RO

RW

""

0

Default Value

RW

RO

RW

RW

""

1

1

0

-

-

-

-

-

-

-

Unit Access

W RO mA RO

-

V RO

RO

RO

RO

RO

RW

RO

RO

RO



Table 12. System CLI Objects (Continued)

XML Object Name

System.DaisyChain.Status

System.Display.Contrast

System.DaisyChain[x].DeviceId

System.DaisyChain[x].MacAddress

System.DaisyChain[x].Position

System.DaisyChain[x].Status

System.Display.Contrast

System.Display.Password

Access right

admin admin admin admin

Type

DaisyChainStatus

Description

0: No Communication

1: Communication OK

2: Communication failed

3: Host conflict

4: Device conflict

Integer25to45

DaisyChainDeviceId 0: Host

1: Device 1

2: Device 2

3: Device 3

String:17

Access

RO

RW

RO

RO

0

32

1

Default Value

"00:00:00:00:00:00"

0 admin admin admin superadmin

DaisyChainPosition 0: Middle

DaisyChainStatus

1: End

0: No Communication

1: Communication OK

2: Communication failed

3: Host conflict (not implemented)

4: Device conflict

Integer25to45

Password:4

RO

RO

RW

RW

0

32

System.Display.Password.IsEnable

System.Display.Language

System.Display.LcdRotation

System.Email.Count

System.Email.Sender

superadmin ControlState RW 1234 superadmin DisplayLanguage admin admin admin

LcdRotation

Integer0to65535

String:31

0: English

1: French

2: German

3: Spanish

4: Russian

5: Portuguese

6: Italian

0: Rotation 0 Deg(0U)




RW

RW

RO

RW

0

NB_EMAIL_NOTIFIC

ATIONS

"[email protected]"




XML Object Name

System.Email[x].Description

System.Email[x].EventList.All

System.Email[x].Events.Log

System.Email[x].Recipient

System.Email[x].Report.Hour

System.Email[x].Report.Next

System.Email[x].Report.Periodicity

System.Email[x].Selected

System.Email[x].Test

System.Ethernet.iVersion

System.Ethernet.MacAddress

System.Ethernet.Mode

NOTE: Reboot is required.

System.FactoryReset

System.FirmwareUpgrade

System.FirmwareUpgradeMode

System.FormatFS

System.KeepDC

System.KeepIP

Access right

admin admin admin admin admin admin admin admin admin admin admin admin

Type

String:63

EventType

ControlState

String:127 admin admin admin

Boolean

Boolean

ControlState superadmin ControlState admin admin

ControlState

ControlState

Description

0: None

1: All Alarms

0: Disabled

1: Enabled

RW

RW

RW

RW

Access

RW

RW

Default Value

"||||||||"

0

RW 0

RW

0

0

0

0

"[email protected]

om|email2@recipien t.com|email3@recipi ent.com|email4@rec ipient.com|email5@ recipient.com|email

[email protected]|em [email protected]| [email protected]

m|email9@recipient

.com"

Time0to23hours

Time0to31days

Time0to28days

ControlState 0: Disabled

1: Enabled

2: Deleted

Boolean

String:15

String:31

EthMode 0: Auto Negotiation

1: 100 Mbps Full Duplex

2: 100 Mbps Half Duplex

3: 10 Mbps Full Duplex

4: 10 Mbps Half Duplex

RO

RW

WO

RW

WO 0: Disabled

1: Enabled

0: Disabled

1: Enabled

WO

RW

0: Disabled

1: Enabled

RW

WO

RO

0

"00.00.0022"

"00.00.0029"

"00.00.0030"

"00:00:00:00:00:00"

0

0

1

0

0

0

0




System.Language

System.Location

System.Login

System.LogReset

XML Object Name

System.Network.Authentication.AuthMethod

System.Network.Authentication.AuthOrder

System.Network.Authentication.MaxSessionTime

System.Network.Authentication.SessionTime

System.Network.DHCP


System.Network.DomainName


System.Network.EnergyWise.Enable

System.Network.EnergyWise.Domain

System.Network.EnergyWise.Secret

System.Network.EnergyWise.SecretKey

System.Network.EnergyWise.RemotePort

System.Network.EnergyWise.ListenPort

admin admin admin admin admin

Access right

admin admin superadmin admin admin admin admin admin admin admin

Type

Language

String:31

String:31

Boolean

AuthMethod

AuthOrder

Integer0toFFFFFFFF

Integer0toFFFFFFFF

ControlState

String:63

Description

2: English (ENG)

3: French (FRE)

4: Spanish (SPA)

5: German (GER)

6: Italian (ITA)

7: Chinese Simplified

(CHI)

8: Japanase (JPN)

9: Korean (KOR)

10 : Chinese Traditionnal

(CHT)

11 : Russian (RUS)

12 : Portuguese (POR)

13 : Czech (CZE)

14 : Polish (POL)

Access

RW

RW

RW

WO

RW 1: Local Authentication

2: LDAP Authentication

3: Radius Authentication

1: Local

2: External then Local

3: Local then External

4: External

RW

0: Disabled

1: Enabled

RW

RW

RW

RW

2

Default Value

0

1

""

"admin"

1

0xFFFFFFF

300

1

"pdu.domain.com" admin ControlState 0:Disable

1:Enable

RW 0

String:63

ControlState

Password:63

Integer1to65535

Integer1to65535

RW

RW

RW

RW

RW

“MyDomain”

0

“”

43440

48296




XML Object Name

System.Network.EnergyWise.SdkVersion

System.Network.EnergyWise.SeqId

System.Network.EnergyWise.ThresholdLevel

System.Network.EnergyWise.State

System.Network.EnergyWise.Cmd

System.Network.FTP.Access

System.Network.HostName


System.Network.HTTP.Access


System.Network.HTTP.Port


System.Network.HTTPS.Port


System.Network.IPAddress


System.Network.IPGateway


System.Network.IPMask


System.Network.IPv6Address1


System.Network.IPv6Address2

System.Network.IPv6AutoConfig


System.Network.IPv6DefaultGateway


System.Network.IPv6Enable


System.Network.IPv6LocalAddress

System.Network.IPv6Status

System.Network.Ldap.AuthMechanism

admin admin admin admin admin admin admin admin admin admin admin

Access right

admin

Type

String:31 admin admin admin admin admin

Integer0to42949672

95

Integer0to10

String:31

EnergyWiseCmd

ControlState

Description

0: Disabled

1: Enabled admin admin admin admin

String:31

ControlState

Integer1to65535

0: Disabled

1: Enabled

Integer1to65535

IPv4

IPv4

IPv4

RW

RW

IPv6

IPv6

ControlState

IPv6

0: Disabled

1: Enabled

RW

ControlState 0: Disabled

1: Enabled

IPv6

NetworkIpv6Status 0: Invalid

LdapAuthMechanis m

1: Valid

2: Manual Configuration

0: Simple

7: Digest MD5

RW

RO

RO

RW

RO

RW

RW

Access

RO

Default Value

RELEASE 1.2.0

RW

RW

RO

RW

RW

0

4

“”

0

1

WO "PDU$x”

RW

RW

RW

RW

1

80

443

"192.168.123.123"

""

"255.255.0.0"

""

""

0

""

0

""

0

0




XML Object Name

System.Network.Ldap.GroupSearch.AuthzMode

Access right

admin

Type

LdapAuthorization

Mode

Description

0: No Authorization

1: By User Attribute

2: By Group

System.Network.Ldap.GroupSearch.BaseDn

admin

System.Network.Ldap.GroupSearch.UPSGroupNameAttr

admin

System.Network.Ldap.GroupSearch.UserNameAttr

System.Network.Ldap.SearchMode

admin admin

String:99

String:49

String:49

LdapSearchMode 0: Anonymous Search

1: User Bind Search

System.Network.Ldap.SearchUser

System.Network.Ldap.SearchUserPassword

System.Network.Ldap.Server.Count

System.Network.Ldap.Server[x].IsEnable

admin admin admin admin

String:99

Password:49

Integer0to10

ControlState

2

0: Disabled

1: Enabled

System.Network.Ldap.Server[x].Port

System.Network.Ldap.Server[x].ServerName

admin admin

Integer1to65535

String:49

System.Network.Ldap.Server[x].TimeOut

System.Network.Ldap.ServerType

System.Network.Ldap.SSLMode

System.Network.Ldap.UserSearch.Attribute

System.Network.Ldap.UserSearch.BaseDn

System.Network.Ldap.UserSearch.Object

System.Network.PrefixLength1

System.Network.PrefixLength2


System.Network.PrimaryDNS


System.Network.Radius.Server[x].IsEnable

System.Network.Radius.Server[x].ServerName

System.Network.Radius.Server[x].SharedSecret

System.Network.Radius.Server[x].Port

System.Network.Radius.Server[x].NasIdentiferType

System.Network.Radius.Server[x].Retry

System.Network.Radius.Server[x].Timeout

System.Network.SecondaryDNS


admin admin admin admin admin admin admin admin admin admin admin admin admin admin admin admin admin

Integer0to65535

LdapServerType

LdapSSLMode

String:49

String:99

String:49

Integer0to128

Integer0to128

IPv4

ControlState

String:48

Integer1to65535

NasIdentifierType

Integer0to255

Integer0to255

Integer1to65535

IPv4

65535

3

9

99

Access

RW 0

Default Value

RW

RW

0: Generic LDAP server

1: Active Directory

0: No SSL

1: SSL (LDAPS)

2: SSL (Start TLS)

RW

RW

RW

RW

RW

RW

RW

RO

RW

RW

RW

RW

RW

RW

RW

RW

RW

RW

RW

RW

RO

RW

RW

RW

RW

0

""

0

""

""

0

2

0

""

""

""

0

""

""

389

"LDAP Server1|LDAP

Server2"

10

0

""

5

""

0

"RADIUS

Server1|RADIUS

Server2"

0

3

""

1812




XML Object Name

System.Network.SmtpServer.Authentication

System.Network.SmtpServer.HostName

System.Network.SmtpServer.Login

System.Network.SmtpServer.Password

System.Network.SmtpServer.Port

System.Network.SNMP.Port

System.Network.SNMP.snmpVersion

System.Network.SNMP.TrapPort

System.Network.SNMP.V1.User.Count

System.Network.SNMP.V1.User[x].SecurityRight

System.Network.SNMP.V1.User[x].UserName

Access right

admin admin admin admin admin admin admin admin admin admin admin

Type

ControlState

Description

0: Disabled

1: Enabled

String:63

String:31

String:31

Integer1to65535

Integer1to65535

SNMPVersion 0: disabled

1: SNMP V1

2: SNMP V3

3: SNMP V1&V3

Integer1to65535

Integer0to65535

Snmpv3VacmSecuri tyRight

0: No Right

1: Read-Only

2: Read/Write

3: Number

String:24

Access

RW 0

Default Value

RW

RW

RW

RW

RW

RW

""

""

""

25

161

0

RW

RO

RW

RW

162

SNMPV1_NBCOMM

UNITIES

0

"public|private"

System.Network.SNMP.V3.User.Count

System.Network.SNMP.V3.User[x].Name

System.Network.SNMP.V3.User[x].Password

System.Network.SNMP.V3.User[x].PrivacyKey

System.Network.SNMP.V3.User[x].SecurityLevel

System.Network.SNMP.V3.User[x].SecurityRight

System.Network.SSH.Port


System.Network.Syslog.Server.Count

System.Network.Syslog.Server[x].IsEnable

admin admin admin admin admin admin admin admin admin

Integer0to65535

String:31

String:24

String:24

Snmpv3UsmLevel

Snmpv3VacmSecuri tyRight

0: Not Set

1: No Auth No Priv

2: Auth No Priv

3: Auth Priv

0: No Access

1: Read-Only

2: Read/Write

Integer1to65535

Integer0to10

ControlState

RO

RW

RW

RW

RW

RW 0

RW

RW

RW

"|||"

"|||"

0

SNMPV3_USM_NB

USERS

"SNMPv3 User

1|SNMPv3 User

2|SNMPv3 User

3|SNMPv3 User 4"

22

2

0




XML Object Name

System.Network.Syslog.Server[x].ServerName

System.Network.Syslog.Server[x].Port

System.Network.Syslog.Server[x].Protocol

System.Network.Syslog.Server[x].BOM

System.Network.Syslog.Server[x].MessageTransfer

System.Network.Syslog.Server[x].Facility

Access right

admin admin admin admin admin admin

Type

String:49

Integer1to65535

SyslogProtocol

Description

0: UDP

1: TCP

ControlState RW

SyslogMessageTra nsfer

SyslogFacility

RW

"0: Octet Counting

1: Non Transparent

Framing"

"0: kernel messages

1: user-level messages

2: mail system

3: system daemons

4: security/authorization messages

5: messages generated internally by syslogd

6: line printer subsystem

7: network news subsystem

8: UUCP subsystem

9: clock daemon

10: security/ authorization messages

11: FTP daemon

12: NTP subsystem

13: log audit

14: log alert

15: clock daemon (note

2)

16: local use 0 (local0)







23: local use 7 (local7)"

RW

Access

RW

RW

Default Value

"Syslog

Server1|Syslog

Server2"

514

RW 0

1

0

1




XML Object Name

System.Network.Syslog.Server[x].Test

System.Network.Telnet.Access


System.Network.Telnet.Port


System.Network.Telnet.Security


System.NetworkManagementSystem.Count

System.NetworkManagementSystem[x].EventList.All

System.NetworkManagementSystem[x].HostName

System.NetworkManagementSystem[x].Name


Access right

admin Boolean

Type

admin ControlState admin Integer1to65535

Description

0: Disabled

1: Enabled

ControlState

Integer0to65535

EventType

String:63

String:31

0: Disabled

1: Enabled

0: None

1: All Alarms

RW

RO

RW

RW

RW

Access

WO 0

Default Value

RW 1

RW 23

WO

RW

RW

0

NB_TRAP_RECEIVE

RS

0

"|||||||"

"Trap Receiver

1|Trap Receiver

2|Trap Receiver

3|Trap Receiver

4|Trap Receiver

5|Trap Receiver

6|Trap Receiver

7|Trap Receiver 8"

0

"public|public|public| public|public|public| public|public"

0

System.NetworkManagementSystem[x].Test

admin

System.NetworkManagementSystem[x].TrapCommunity

admin

Boolean

String:24

System.NetworkManagementSystem[x].TrapSnmpVersio

n

System.Password

System.Restart

System.Security


System.Slip.Statistic

System.Temperature.Unit

System.Time

System.TimeDaylight

System.TimeFormat

System.TimeNtp

admin SNMPVersion 0: Disabled

1: SNMP V1

2: SNMP V3 superadmin admin admin

Password:15

Boolean

ControlState admin admin admin admin admin admin

0: Disabled

1: Enabled

String:31

TemperatureUnit

Time0to136years

ControlState

DateTimeFormat

0: Disabled

1: Enabled

1: mm/dd/yyyy

2: dd/mm/yyyy

3: yyyy-mm-dd

4: dd mm yyyy

String:63

1: °C

2: °F

RW

WO

RW

RO

RW

RW

RW

RW

0

0

""

1

"admin"

0

0

2

RW ""




XML Object Name

System.TimeSync

System.TimeUp

System.TimeZone

System.User.Count

System.User[x].Login

System.User[x].Password

System.User[x].Status

System.User[x].Type

Access right


Type

DateTimeSource

Time0to136years

DateTimeTimeZone

Integer0to65535

String:31

Description

0: Manual

1: Sync NTP admin admin admin

Password:15

ControlState

MultiUserType

0: Disabled

1: Enabled

0: local

1: remote

RW

RW

RW

Access

RW 0

Default Value

RO

RW

RW

RW

0

0

MAX_NB_USERS

"Account 1|Account

2|Account 3|Account

4|Account 5|Account

6|Account 7|Account

8"

"|||||||"

0

0


Chapter 9 Maintenance and Alarms

This section explains maintenance functions for the HP Managed PDU, including: l

Preventive maintenance l

Equipment disposal l

Replacing the eNMC module l

Updating Firmware l

Alarms

Preventive Maintenance

For the best preventive maintenance, keep the area around the MA PDU clean and dust-free. If the atmosphere is very dusty, clean the outside of the system with a vacuum cleaner. Do not to exceed 60°C (140°F) for best performance.

Equipment Disposal

Contact your local recycling or hazardous waste center for information on proper disposal of the used MA PDU.

CAUTION

Do not discard waste electrical or electronic equipment (WEEE) in the trash. For proper disposal, contact your local recycling/reuse or hazardous waste center.

Replace the MA PDU eNMC Module

NOTE

Handle the eNMC module with care. Be aware that there is a risk of ESD

(electrostatic discharge). As a preventive measure, wear ESD protection, such as an

ESD shoe strap, while replacing the eNMC module. Do not put stress on the connection cable during installation.

A hardware configuration file specific to the MA PDU model needs to be uploaded to the new eNMC module so that the eNMC module knows the characteristics of the MA PDU model in which it resides (such as what type of input, how many circuit breakers, how many outlets, and how measurements should be displayed).

Typically, the eNMC module in your MA PDU will be replaced because it is not working. However, you may want to replace a working eNMC module.

Replace an eNMC that is Not Working

Either obtain the hardware configuration file from another working MA PDU of the same model type and configuration, or download the firmware from the HP Web site and use the configuration files for your model as contained in the package. Then, you need to upload the MA PDU model-specific hardware description file to the new eNMC module after it is installed.

Replace a Working eNMC

The resident MA PDU model’s hardware description file can be downloaded before you remove the eNMC module. Save the file to a USB drive or save the file to your computer using FTP. Then, you can restore this file to the new eNMC module after you install it.


Maintenance and Alarms

NOTE

The eNMC module is hot-swappable. This means outlets will not be affected or change On/Off state during the replacement process.

NOTE

See “USB Flash Mode Submenu” on page 48 for more information about saving

and uploading the user configuration files that store the settings customized by the user, such as the network parameters, outlet names, and threshold values.

To replace the eNMC module (see Figure 60):

1 2

3

4

5 6

Figure 60. Replacement Procedure

1.

Remove the two eNMC module mounting screws.

2.

Tilt up one side of the eNMC module and locate the attached cable harness.

3.

Disconnect the cable harness and remove the eNMC module.

4.

Locate and unwrap the new eNMC module. Connect the cable harness to the new eNMC module.

5.

Reinsert the new eNMC module.

6.

Install the two eNMC module mounting screws.

NOTE

After the new eNMC module is connected, the “internal communication error” message displays until the configuration file is uploaded to the eNMC module.

7.

The new eNMC module will not have the same MAC address as the one you are replacing. Ensure the old

MAC address label is discarded and that new MAC address label is firmly adhered to the product.

8.

Download the MA PDU model’s hardware configuration file using one of the following processes: l

From the Web to your computer (go to Step 9)

l

To the USB with an MA PDU with the same configuration (go to Step 13)

9.

Go to www.HP.com/support/mPDU_manuals.



10. Obtain the hardware configuration file in one of the following ways: l

Copy the hardware configuration file from another working MA PDU (must be the same model type and configuration).

l

Download the firmware upgrade package from the HP Web site and use the attached configuration files for your model.

11. Save the MA PDU model-specific hardware configuration file to your computer. See Table 8 on page 50.

!

IMPORTANT

Be sure that the Configuration number on the unit rating label also appears in the file name of the model-specific MA PDU hardware configuration file.

12. Go to Step 19.

13. Make sure the eNMC module is powered ON. Connect a USB flash drive to a working MA PDU.

!

IMPORTANT

This MA PDU must be of the same model type and configuration as the MA PDU that houses the eNMC module you will replace.

14. When the LCD interface pop-up confirms that the USB flash drive is detected, click OK, and press Enter to return to the Main Menu. (If not confirmed within 10 seconds, the pop-up goes away by itself.)

15. From the LCD Settings menu, select USB Flash Mode. Press Enter, select yes to confirm, and then press


Flash Mode. Remove and reinsert the flash drive to access this menu again.)

16. Select Save eNMC file to save the MA PDU hardware configuration file to the USB drive. The file will save to the eNMC/config/hw path at the USB drive root directory.

17. When the file is saved, click OK to confirm.

18. Disconnect the USB drive from the working MA PDU.

19. Upload the PDU hardware configuration file using one of the following processes: l

FTP (Step 20)

l

USB (Step 30)

NOTE

To perform the eNMC module configuration upload with USB, only one hardware configuration file must be stored in the USB key.

NOTE

For FTP operation, FTP must be enabled (default setting) in the Web pages

(Network > Security > Global > FTP enable).

20. Open a DOS command window on a computer that is also connected to network.

21. Change directory (CD) to the location of the XML file.



22. Open an FTP session using the following command:

>ftp <IPaddress>

where <IPaddress> = the IP address displayed on LCD

23. Type the default login and password (“admin” and “admin”).

24. At the command prompt, type the following command:

>cd config/hw

>dir

25. If an MA PDU hardware configuration file (XML) file already exists, type the following command to delete the file:

>delete <config file>

26. To upload the MA PDU hardware configuration file to the eNMC module, type the following command:

>put <config file>

where <config file> = the file name to be downloaded to the eNMC module

NOTE

Keep the <config file> name exactly as it is downloaded from the website. It must begin with the prefix “epdu_cfg_*” or the eNMC module will not recognize it.

27. Type the following command to verify the file has been uploaded:

>dir

28. Type the following command to quit the FTP session:

>quit

29. Go to the “Restart the eNMC Module and Reset the MA PDU”procedure that follows.

30. Make sure the eNMC module is powered on. Connect the USB flash drive to the MA PDU with the new eNMC.

31. When the LCD interface pop-up confirms that the USB flash drive is detected, click OK, then press Enter to return to the Main Menu. (If not confirmed within 10 seconds, the pop-up goes away by itself.)

32. From the LCD Settings menu, select USB Flash Mode. Press Enter, select Yes to confirm, and then press


Flash Mode. Remove and reinsert the USB flash drive to access this menu again.)

33. Select Load eNMC file, then click OK to upload the MA PDU hardware configuration file to the eNMC.

34. When the file is successfully loaded, click OK to confirm.

35. Remove the USB flash drive and select Exit.

36. Go to the “Restart the eNMC Module and Reset the MA PDU”procedure that follows.



Restart the eNMC Module and Reset the MA PDU

1.

Restart the eNMC module using either the reset button on the LCD front panel (see “Restarting the eNMC Module” on page 37) or using a serial or network connection to a terminal emulator or Web

interface.

2.

Reset the MA PDU to factory default settings using one of the following: l

Web interface “Configure PDU Network Management Card Data” on page 78

(System > Network Management Card Configuration panel > Restore Factory default settings >

Yes) l

LCD menu “Factory Submenu” on page 55

(Settings > Factory > Return to Factory Settings > Yes > OK)

NOTE

Step 1 and Step 2 must be performed or the new configuration will not be properly

accepted by the eNMC module.To see if the new configuration was accepted, you can check to see if the serial number displays from the PDU Info menu. If not, the new configuration was not accepted. Perform step 2 (reset to defaults) again.

After the MA PDU hardware configuration file is uploaded and eNMC module is rebooted and reset to factory defaults, the MA PDU settings return to default settings and the energy counter restarts from 0. Only the serial number is recovered.

Firmware Upgrade

The firmware upgrade process allows you to maintain the most current firmware by updating the eNMC with new or enhanced features and applying periodic bug fixes.

The upgrade file is named Image<xxx>.bin. (The <xxx> values will vary for each upgrade.) During the upgrade, the firmware and the Web page are both upgraded to avoid incompatibility between the firmware version and the Web site. Additional validation checks are performed as well.

The new firmware files can be uploaded using either HTTP (Hypertext Transfer Protocol), FTP (File Transfer

Protocol), or USB. With all methods, the basic steps are the same:

1.

Upload the Binary File. This file will be stored in a temporary location in the eNMC module.

2.

Implement the Firmware. After the file is loaded, the bootloader will implement the firmware in the eNMC module to upgrade the firmware and refresh the Web pages.

Upgrade Firmware with Hypertext Transfer Protocol

The HTTP upgrade using the Web occurs in two stages: l

Upload the binary file l

Implement the firmware

Upload the Binary File


1.

Ensure that an Ethernet cable is correctly connected between a Windows PC and the Ethernet port on the

PDU. Verify communication.

2.

Start up the PDU and note the IP address displayed on the LCD.

3.

Open the Web browser and type the IP address you obtained from the PDU.

4.

When the connection is made, the Authentication dialog displays.



5.

Enter a valid user name and password in the authentication dialog box (see Figure 61). Click Login to

continue or Cancel to exit.

NOTE

The default user name is “admin” and the default password is “admin.”

Figure 61. Login Authentication

6.

The MA PDU Overview page displays.

7.

From the menu bar, click Settings and then System. The System Settings page displays in the Main

Application window (see Figure 62).

8.

In the Network Management Card panel, check Firmware upgrade enabled and click Browse to find the upgrade file.



Figure 62. System Settings Page

9.

From the Open window, select the Image<xxx>.bin file, and click Open.

10. In the Network Management Card panel, click Upgrade Network Management Card to launch the upload. A progress bar shows the progress of the update.

CAUTION

Do not disturb the upgrade until the progress bar shows complete.

11. When finished, a message displays and the eNMC module restarts automatically. The upgrade takes four to five minutes. When the upgrade completes, refresh the Web pages.



Upgrade the Firmware and Refresh Web Pages

After the binary file is uploaded to the eNMC module, the final step is an automatic process that upgrades the firmware and refreshes the Web pages.

The eNMC module reboots and, in Bootloader mode, detects a new available image, checks validity of this image, and launches the upgrade of the firmware and refresh the Web pages. As the upgrade processes, a message box displays with percent completed.

When completed, an upgrade message displays F/W: 100%, and the eNMC module reboots with the new firmware and refreshed Web pages.

Upgrade the Firmware with FTP Protocol

The FTP upgrade occurs in two stages: l

Upload the binary file l

Implement the firmware

NOTE

The FTP server must be enabled for this procedure. This an option on the Global

Security page of the Web interface.

Upload the Binary File


1.

Ensure that an Ethernet cable is correctly connected between a Windows PC and the Ethernet port on the

PDU. Verify communication.

2.

Start up the PDU and note the IP address displayed on the LCD.

3.

Open an MS-DOS command line window and connect to the eNMC module in FTP mode (see Figure 63):

l

Type FTP @IP, where @IP is the previous IP address.

l

Type the user name and password of the SuperUser.

l

Type the hash command. This allows you to follow the upload as it progresses.

4.

At the ftp> command line, use the put command with the Image<xxx>.bin file to launch the upgrade

(see Figure 63).



Figure 63. Launching the Upgrade

5.

When the upgrade finishes, the closing message displays (see Figure 64).

Figure 64. Closing Message

Upgrade the Firmware and Refresh Web Pages

After the binary file is uploaded to the eNMC module, the final step is an automatic process that upgrades the firmware and refreshes Web pages.

The eNMC module reboots and, in Bootloader mode, detects a new available image, checks validity of this image, and launches the upgrade of the firmware and refresh the Web pages. As the upgrade processes, the

LCD display shows the completion status.

When completed, an upgrade message on the LCD displays F/W: 100%, and the eNMC module reboots with the new firmware and refreshed Web pages.



Upgrade the Firmware with the USB Port

See “Settings Menu”and “USB Flash Mode Submenu” on page 48 for more information of upgrading with

the USB.

Active Alarms

The HP MA PDUs have a rich set of alarms and events to notify you of up-to-date activity and operation status.

Both the local MA PDU LCD interface and the remote Web interface provide active alarm notifications when alarms become active.

l

On the LCD interface, the existing LCD display is replaced by the Active Alarms screen and the backlight is blinking red when an alarm is generated. l

On the Web interface, two active alarm notifications are provided:

- In the menu hierarchy, the text for Active Alarms is red when alarms are active.

- In the bottom of the window (the refresh bar), a message displays, “Warning, some alarms fired, please refer to the Active Alarms | Last Refresh: dd/mm/yyyy - hh:hh:ss.” The words “Active Alarms” in the message are a link to the Active Alarms page.

NOTE

The alarm and event list is subject to change.

NOTE

For LCD interface information, see “Active Alarms Menu” on page 42. For Web

interface information, see “Web Interface Operation” on page 57.

l

To clear flashing LCDs and the LED:

- Press any button on the MA PDU or clear the alarm using the Web interface.

l

To correct a condition:

- Define the alarm condition and resolve the condition.

l

Self-correcting conditions:

- Sometimes, the alarm automatically clears when the condition resolves. For example, if a load over current alarm is generated, the alarm is cleared when the current drops 0.1A below the level (alarm hysteresis).

Define the Alarm or Event Condition

You can derive defining information about the alarm or event from the associated number code. Figure 65

shows the location of the associated number code in the Code column on the Logs page of the Web interface.



Figure 65. Location of Alarm Code on Web Interface

This number code is a six-digit number. The first digit in the number conveys the source of the alarm or event.

The remaining five digits in the number code further identify and define the type of alarm.

Alarm Code Syntax

[x][yyyyy] or [x][zzz][aa]

1-Digit Type Code [x]:

0 = OS

1 = System

2 = PDU

3 = User

5-Digit Identification Code [yyyyy] or 3-Digit Identification code [zzz] and 2-Digit Index Code [aa]:

For Type 0 and Type 1 = Identification Code (0 to 9999)

For Type 2 and Type 3 = Identification Code (0 to 999) and Index Code (0 to 99)



Type Code 0 or 1 (OS or System)

!

IMPORTANT

For Type Code 0 and Type Code 1, always contact customer support for assistance. These errors are not user-correctable.

The Type Code 0 and Type Code 1 alarms and events are triggered from the OS or the system. These type codes only contain an 5-digit identification code (no index code).

Example Type 1 System Alarm Number Code

[1][02820]

Number code 102820 = No answer from a CAN device

Type Code = 1 (System)

Identification Code = 02820

Table 13 lists System alarms and events.

Table 13. System Alarms and Events

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

Type

Code Identification Code

02822

02823

02824

02825

02826

02827

01281

01282

03073

03074

03075

02817

02818

02819

02820

02821

01283

01284

01285

01286

01282

02561

02562

02563

02564

Alarm or Event

Code unreachable

Heap overflow

Not enough memory in Heap

A command is sent to an unavailable device CAN

*Not used

Impossible to open a session with a CAN device

No answer from a CAN device

*Not used

The number of CAN devices discovered on CAN bus is too great

Command unknown

Device CAN Id out of range

Time duration of a command is too long

Report acquired from CAN device is wrong

Report descriptor acquired from CAN device is wrong

Mutex not available

HID object Id out of range

Report empty or not valid

Report Id out of range

Not enough memory in HEAP

Duration of the acquisition of Teridian is too long

HID object Id not in list of data saved in EEPROM

*Not used

*Not used

*Not used

Wrong data type



Table 13. System Alarms and Events (Continued)

Identification Code

01030

01031

01032

01033

03076

03077

03078

03585

02565

02566

02567

01025

01026

01027

01028

01029

03586

03587

03588

03589

03590

03591

03592

04865

04866

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

Type

Code Alarm or Event

String too long

*Not used

*Not used

*Not used

Semantic error

Impossible to open log file

Impossible to write data in log file

Impossible to seek data in log file

Impossible to read data in log file

Mutex not available

*Not used

Impossible to clear LOG file

Error writing in flash memory during an upload

End signature of the uploaded file does not match

Checksum of the uploaded file does not match

Initialization of SSH task failed

Reading of the host key file (or table) failed

Listening of SSH socket failed

Acceptance of SSH socket failed

Break received

Max number of SSH connection reached

Certificate error

*Not used

Error reading from the 12C Eeprom

Error writing to the 12C Eeprom

Type Code 2 or 3 (PDU or User)

Type 2 alarms and events are triggered from the PDU. These alarms and events are primarily threshold crossings when the operation measurement is beyond the threshold value range setting. Type 2 alarms and events also provide the state of optional connected equipment.

Type 3 alarms and events are triggered from user actions.

Example Type 2 System Alarm Number Code

[2][114][02]

Number code 211402 = PDU Critical Overcurrent L2 Phase

Type Code = 2 (PDU)

Identification = 114

Index code = 02



Table 14 lists PDU and User alarms and events.

Type Code

2

2

2

2

2

2

2

2

2

2

2

2

Table 14. MA PDU and User Alarms and Events

2

2

2

2

2

2

2

2

2

2

2

2

2

2

Identification and

Index Code

201000

201100

202000

202100

203000

203100

204000

204100

205000

205100

208000

208100

206000

206100

206200

206300

206400

207000

207100

207200

207300

207400

211000

211100

211200

211300

Alarm or Event Description

Dry Contact 1 Active

Dry Contact 1 Not Active

Dry Contact 1 Open

Dry Contact 1 Closed

Dry Contact 2 Active

The signal for Dry Contact 1 is active.

The signal for Dry Contact 1 is not active.

Dry Contact 1 is open.

Dry Contact 1 is closed.

The signal for Dry Contact 2 is active.

Dry Contact 2 Not Active

Dry Contact 2 Open

Dry Contact 2 Closed

Sensor Probe Communication Failure Cleared Sensor Probe communication failure is cleared

Sensor Probe Communication Failure

Sensor Probe Not Connected

Sensor probe communication failure detected

Sensor probe not connected since firmware startup

Sensor Probe Connected

The signal for Dry Contact 2 is not active.

Dry Contact 2 is open.

Dry Contact 2 is closed.

Humidity No Threshold

Humidity Warning Low Threshold

Humidity Critical Low Threshold

Humidity Warning High Threshold

Humidity Critical High Threshold

Temperature No Threshold

Temperature Warning Low Threshold

Temperature Critical Low Threshold

Temperature Warning High Threshold

Temperature Critical High Threshold

PDU Phase Input Current No Threshold

PDU Phase Low Current Warning

PDU Phase Low Current Critical

PDU Phase Over Current Warning

Sensor probe connected at least once since firmware startup

No humidity threshold has been triggered.

The humidity level reading is less than the value configured as the low humidity warning threshold.

The humidity level reading is less than the value configured as the low humidity critical threshold.

The humidity level reading is greater than the value configured as the high humidity warning threshold.

The humidity level reading is greater than the value configured as the high humidity critical threshold.

No temperature threshold has been triggered.

The temperature level reading is less than the value configured as the low temperature warning threshold.

The temperature level reading is less than the value configured as the low temperature critical threshold.

The temperature level reading is greater than the value configured as the high temperature warning threshold.

The temperature level reading is greater than the value configured as the high temperature critical threshold.

No section current threshold has been triggered.

The current amperage (A) reading for the specified section is less than the value configured as the low current warning alarm threshold.

The current amperage (A) reading for the specified section is less than the value configured as the low current critical alarm threshold.

The specified section current amperage (A) reading is greater than the value configured as the over current warning threshold.



Table 14. MA PDU and User Alarms and Events (Continued)

2

2

Type Code

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2


Index Code

211400

Alarm or Event

PDU Phase Over Current Critical

212000

212100

212200

212300

212400

213000

213100

221000

221100

221200

221300

221400

222000

222100

222200

222300

222400

241000

PDU Phase Voltage No Threshold

PDU Phase Low Voltage Warning

PDU Phase Low Voltage Critical

Description

The specified section current amperage (A) reading is greater than the value configured as the over current critical alarm threshold.

No section voltage threshold has been triggered.

The specified section voltage reading is less than the value configured as the low voltage warning threshold.

The specified section voltage reading is less than the value configured as the low voltage critical threshold.

PDU Phase Over Voltage Warning

PDU Phase Over Voltage Critical

PDU Frequency OK

The specified section voltage reading is greater than the value configured as the over voltage warning threshold.

The specified section voltage reading is greater than the value configured as the over voltage critical threshold.

Utility frequency is within the +/- 3 Hz of Nominal frequency.

PDU Frequency Out of Range

PDU Gang Phase Input Current No Threshold No section current threshold has been triggered.

PDU Gang Phase Low Current Warning The current amperage (A) reading for the specified section is less than the value configured as the low current warning alarm threshold.

PDU Gang Phase Low Current Critical

Utility frequency greater or less than +/- 3 Hz of

Nominal frequency.

PDU Gang Phase Over Current Warning

The current amperage (A) reading for the specified section is less than the value configured as the low current critical alarm threshold.

The specified section current amperage (A) reading is greater than the value configured as the over current warning threshold.

PDU Gang Phase Over Current Critical

PDU Gang Phase Voltage No Threshold

PDU Gang Phase Low Voltage Warning

PDU Gang Phase Low Voltage Critical

The specified section input current amperage (A) reading is greater than the value configured as the over current critical alarm threshold.

No section voltage threshold has been triggered.

The specified section voltage reading is less than the value configured as the low voltage warning threshold.

The specified section voltage reading is less than the value configured as the low voltage critical threshold.

PDU Gang Phase Over Voltage Warning

PDU Gang Phase Over Voltage Critical

Communication OK

The specified section voltage reading is less than the value configured as the over voltage warning threshold.

The specified section voltage reading is less than the value configured as the over voltage critical threshold.

No communication failure detected on Teridian

RS-485 bus



Table 14. MA PDU and User Alarms and Events (Continued)

2

2

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

Type Code

2


Index Code

241100

Alarm or Event

Communication Lost

251000

251100

300100

300200

300300

300400

300500

300600

300700

300800

300900

301000

301100

301200

301300

301400

301500

301600

301700

301800

301900

302000

Communication OK

Communication Lost

Communication module restarted

Ethernet cable connected

Ethernet cable not connected

Factory reset requested by <interface>

Ethernet card restart requested by

<interface>

Switch to bootloader mode for upgrade by

<interface>

PDU & System Log cleared

Daisy Chain device does not answer

Time changed

Daisy chain device connected

Daisy chain device disconnected

Upgrade request by user

Sensor connected

Sensor disconnected

Send mail test by user

User logged in

User logged out

User logged in by FTP

User logged out by FTP

User login by FTP failed

Description

Communication failure detected on Teridian RS-485 bus

No communication failure detected on Daisy-chained device

Communication failure detected on Daisy-chained device

The communication module has been restarted by the user.

The Ethernet cable is connected.

The Ethernet cable is not connected.

A factory reset has been requested through the specified user interface.

An Ethernet card restart has been requested through the specified user interface.

A Switch to bootloader mode for upgrade has been requested through the specified user interface.

The PDU & System Log have been cleared.

The Daisy Chain device does not answer.

The time was changed by the user.

The daisy chain device is connected.

The daisy chain device is disconnected.

An upgrade was requested by the user.

The sensor was connected.

The sensor was disconnected.

The user sent a mail test.

The specified user logged in by the specified protocol.

The specified user logged out by the specified protocol.

The specified user logged in by FTP.

The specified user logged out by FTP.

The specified user failed to log in by FTP.


Chapter 10 Specifications

This chapter lists the following specifications for the HP Managed PDU models: l

Model list l

Weights and dimensions l

Electrical input and output l

Electrical ratings l

Overcurrent protection l

Environmental and safety l

RMNs (Regulatory Compliance Model Numbers)

Model List

Table 15 lists the MA PDU models and descriptions.

Table 15. Model List

Model

H8B48A

H8B49A

H8B50A

H8B51A

H8B52A

H8B53A

H8B54A

H8B55A

H8B56A

Description


HP 3.6kVA 100-240V 16A WW maPDU


HP 7.3kVA 200-240V 32A INTL maPDU


HP 8.6kVA 208V 30A 3Ph DV NA/JP maPDU

HP 11kVA 400V 16A 3Ph INTL maPDU



Weights and Dimensions

Table 16 lists weights and dimensions for the MA PDU models.

Table 16. Weights and Dimensions

Model Form Factor

H8B48A

H8B49A

H8B50A

H8B51A

H8B52A

H8B53A

H8B54A

H8B55A

42U

22U

42U

42U

42U

42U

42U

42U

H8B56A 42U

NOTE

Circuit breakers require additional clearance.

Weight (kg)

6.23

6.00

4.60

9.94

10.47

5.24

1.84

5.33

4.92

Length in millimeters

(mm)

1689.0

902.0

1689.00

1689.00

1689.00

1689.00

1689.00

1689.00

1689.00

Width in millimeters

(mm)

52.0

52.0

52.0

52.0

52.0

52.0

52.0

52.0

52.0

Depth in millimeters

(mm) SEE NOTE

65.0

53.0

53.0

65.0

65.0

65.0

53.0

53.0

53.0


Specifications

Electrical Input and Output

Table 17 and Table 18 list the electrical input and output characteristics for the MA PDU models.

Table 17. Electrical Input and Output (All MA PDU Models)

Input Frequency

Input Voltage Tolerance

Output Frequency

Output Voltage Range

Output Voltage Tolerance

50/60 Hz

±3 Hz

+6% / -10%

50/60 Hz

±3 Hz

See Table 19 on page 138.

+6% / -10%

Table 18. Electrical Input and Output (By Model)

Model Phases Plug/Inlet C13 Outlets C19 Outlets 5-20R Outlets

H8B48A

H8B49A

H8B50A

H8B51A

H8B52A

H8B53A

H8B54A

H8B55A

1P

1P

1P

1P

3P

3P

3P

3P

NEMA L5-30P

IEC 60320 C20

SEE NOTE

NEMA L6-30P

IEC 60309 32A 3-wire

NEMA L15-30P

NEMA L21-30P

IEC 60309 16A 5-wire

CS8365C 50A 4-wire

—

7

20

20

18

20

21

12

—

1

4

4

6

3

3

12

H8B56A 3P IEC 60309 60A 4-wire Watertight 12 12

NOTE

See “3Ph Configurations” on page 33 for an explanation of input connector codes for 3Ph configuration topologies.

—

1

—

—

—

24

—

—

—

NOTE

Outlets conform to the relevant outlet standard. For IEC 60320 C13 and

IEC 60320 C19 outlets, the relevant standards are UL-498 and IEC 60320.

Electrical Ratings

Table 19 and Table 20 list the electrical ratings for the MA PDU models.

Table 19. Electrical Ratings

Model

H8B48A

H8B49A

H8B50A

H8B51A

H8B52A

H8B53A

H8B54A

H8B55A

H8B56A

Input Voltage

100-127V

100–240V

200–240V

200–240V

200–240V

120 / -208V

200/240 / -346-415V

200–240V

200–240V

Output Voltage

100-127V

100–240V

200–240V

200–240V

200–240V

120V and 208V

200-240V

200–240V

200–240V

24

24

16

40

48

24

16

24

32

Input Current (A) Capacity (VA)

2880

3680

4992

7360

8646

8646

11040

14410

17292


Specifications

Table 20. Output Current Ratings (All MA PDU Models)

Outlets

IEC 60320 C13

IEC 60320 C19

NEMA 5-20R

10A

16A

16A

Ratings

Overcurrent Protection

Table 21 lists the overcurrent protection requirements for the MA PDU models with outlet groups protected by

circuit breakers.

Table 21. Overcurrent Protection

Model Breaker Qty Breaker Type SEE NOTE Breaker Rating (A)

H8B48A

H8B49A

H8B50A

H8B51A

H8B52A

H8B53A

H8B54A

H8B55A

2

0

2

2

3

3

0

6

SP

—

DP

SP

DP

DP

—

DP

20A

—

20A

16A

20A

20A

—

20A

H8B56A 6 DP 20A

NOTE

SP = Single Pole; DP = Double Pole

Each PDU has one branch-rated circuit breaker for over-current and short circuit protection on each output load segment. The breaker opens each current carrying conductor (double pole), except for line-to-neutral wiring schemes, where single-pole circuit breakers are used on the “hot” conductor only. The breakers meet the requirement of UL489 for the U.S. and IEC/EN 60934 for

Europe.

Environmental and Safety

Table 22 lists the environmental specifications for all MA PDU models.

Table 22. Environmental Specifications (All PDU Models)

Operating Temperature (Room Ambient)

Shipping and Storage Temperature

Relative Humidity

Operating Altitude

Shipping and Storage Altitude

0

°C to 50

°C

(32

°F to 122

°F) for INTL and WW models with outlet derating

0

°C to 60

°C

(32

°F to 140

°F) on all other NA/JPN models (except as noted previously)

Transit: -30

°C to 60

°C

(-22

°F to 140

°F) (up to 72 h)

Storage: -20

°C to 60

°C

(-4

°F to 140

°F)

5–95% relative humidity

Up to 3,048m (10,000 ft) above sea level

(derated for higher altitude applications)

Up to 12,200m (40,000 ft) above sea level


Specifications

Table 23 lists safety information for all MA PDU models.

Table 23. Safety Specifications (All PDU Models)

Safety Conformance

Safety Conformance (Breakers and Outlets)

EMC (Class A), North American, Japanese and

WorldWide models

UL 60950-1, CSA 60950-1, C22.2 No.29 & No.31 (CSA), IEC/EN 60950-1

Outlets: UL 498, IEC 60320

Breakers: UL 489 for the U.S. and IEC/EN 60934 for Europe

FCC 47 CFR 15, Subpart B: 2009; ICES-003; VCCI

EMC (Class A), International models

EN 55022: 2007; EN 55024: 1998 + A2: 2003; CISPR Publication 22 Class A: 2006 + 2008;

EN 61000-3-2 and EN 61000-3-3 (if the input current is less than or equal to 16A)

EN 61000-3-11 and EN 61000-3-12 (if the input current is greater than 16A)

IEC 61000-4-2; IEC 61000-4-3, IEC 61000-4-4, IEC 61000-4-5, IEC 61000-4-6, IEC 61000-4-8,

IEC 61000-4-11

Table 24 lists the safety standards and country agency certifications for the MA PDU models.

Table 24. Safety Standards and Country Agency Certification

Agency RMN * Model

CE Mark

EN

60950-1 cULus UL 60950-1

and

FCC Part 15 Subpart

B: 2009

and

ICES-003

(EMC Canada)**

HSTNR-P049-1 H8B48A

HSTNR-P048-1 H8B49A

HSTNR-P049-2 H8B50A

HSTNR-P049-3 H8B51A

HSTNS-P050-2 H8B52A

HSTNS-P050-3 H8B53A

HSTNS-P050-1 H8B54A

HSTNS-P050-5 H8B55A

—

•

—

•

—

—

•

—

•

•

•

—

HSTNS-P050-6 H8B56A — •

* See “Regulatory Model Numbers” information that follows.

•

•

—

•

** CAN/CSA-CEI/IEC CISPR22-10

CB

IEC

60950-1

•

•

•

•

•

•

•

•

•

VCCI

•

•

—

•

•

•

•

•

—

DEMKO EAC

—

—

•

—

—

—

•

—

•

—

—

•

—

—

—

•

—

•

KC

K

60950-1 ACMA Ukraine

—

—

•

—

—

—

•

—

•

—

•

—

•

—

—

•

—

—

—

—

•

—

—

—

•

—

•

Regulatory Model Numbers

For regulatory compliance certifications and identification, MA PDUs have been assigned a unique RMN

(Regulatory Model Number). The RMN is on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to the RMN.

The RMN is not the marketing name or model number of the product.


Chapter 11 Support and Other Resources

Before You Contact HP

Be sure to have the following information available before you call HP: l

Active Health System log (HP ProLiant Gen8 or later products)

Download and have available an Active Health System log for 3 days before the failure was detected. For more information, see the HP iLO 4 User Guide or HP Intelligent Provisioning User Guide on the HP website

(http://www.hp.com/go/ilo/docs).

l

Onboard Administrator SHOW ALL report (for HP BladeSystem products only)

For more information on obtaining the Onboard Administrator SHOW ALL report, see the HP website

(http://www.hp.com/go/OAlog).

l

Technical support registration number (if applicable) l

Product serial number l

Product model name and number l

Product identification number l

Applicable error messages l

Add-on boards or hardware l

Third-party hardware or software l

Operating system type and revision level

HP Contact Information

For United States and worldwide contact information, see the Contact HP website (http://www.hp.com/go/ assistance).

In the United States: l

To contact HP by phone, call 1-800-334-5144. For continuous quality improvement, calls may be recorded or monitored.

l

If you have purchased a Care Pack (service upgrade), see the Support & Drivers website (http:// www8.hp.com/us/en/support-drivers.html). If the problem cannot be resolved at the website, call

1-800-633-3600. For more information about Care Packs, see the HP website (http:// pro-aq-sama.houston.hp.com/services/cache/10950-0-0-225-121.html).

HP Product QuickSpecs

For more information about product features, specifications, options, configurations, and compatibility, see the product QuickSpecs on the HP Product Bulletin website (http://www.hp.com/go/productbulletin).

Documentation Feedback

HP is committed to providing documentation that meets your needs. To help us improve the documentation, send any errors, suggestions, or comments to Documentation Feedback (mailto:[email protected]).

Include the document title and part number, version number, or the URL when submitting your feedback.


No results