WV-CPR460 COVER

WV-CPR460 COVER
ENGLISH
Colour CCTV Cameras
Operating Instructions
WV-CPR460
WV-CPR464E
(Lens : option)
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
FRANÇAIS
Model No.
ENGLISH VERSION
For U.K.
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
CAUTION
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THIS APPARATUS MUST BE EARTHED
IMPORTANT
The wires in this mains lead are coloured in accordance with the following
code.
Green-and-yellow:
Earth
Blue:
Neutral
Brown:
Live
As the colours of the wire in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your
plug, proceed as follows.
The wire which is coloured green-and-yellow must be connected to
the terminal in the plug which is marked with the letter E or by the earth
symbol I or coloured green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal in
the plug which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal
in the plug which is marked with the letter L or coloured red.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK), NO USER SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
interned to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that
may be of sufficient magnitude to constitute a risk of electric shock to persons.
The serial number of this product may be found on the top
of the unit.
You should note the serial number of this unit in the space
provided and retain this book as a permanent record of
your purchase to aid identification in the event of theft.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating
and maintenance (servicing) instructions in the literature accompanying the
appliance.
Model No.
Serial No.
WARNING:
TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
-2-
We declare under our sole responsibility that the product to
which this declaration relates is in conformity with the standards
or other normative documents following the provisions of
Directives EEC/73/23 and EEC/89/336.
PREFACE .................................................................... 4
FEATURES .................................................................. 4
PRECAUTIONS ........................................................... 5
MAJOR OPERATING CONTROLS AND
THEIR FUNCTIONS ..................................................... 6
CONNECTIONS .......................................................... 9
SYSTEM CONNECTION..............................................12
FOCUS OR FLANGE-BACK ADJUSTMENT .............. 13
INSTALLATION OF CAMERA .................................... 16
SETUP ....................................................................... 17
1. CAMERA SET UP MENU .................................... 17
2. SETUP OPERATION ........................................... 17
SETTING PROCEDURES .......................................... 22
SPECIFICATIONS ...................................................... 38
STANDARD ACCESSORIES ...................................... 39
OPTIONAL ACCESSORIES.........................................39
Wir erklären in alleiniger Verantwortung, daß das Produkt, auf
das sich diese Erklärung bezieht, mit der folgenden Normen
oder normativen Dokumenten übereinstimmt. Gemäß den
Bestimmungen der Richtlinite 73/23/EEC und 89/336/EEC.
Nosotros declaramos bajo nuestra única responsabilidad que el
producto a que hace referencia esta declaración està conforme
con las normas u otros documentos normativos siguiendo las
estipulaciones de la directivas CEE/73/23 y CEE/89/336.
Noi dichiariamo sotto nostra esclusiva responsabilità che il
prodotto a cui si riferisce la presente dichiarazione risulta conforme ai seguenti standard o altri documenti normativi conformi
alle disposizioni delle direttive CEE/73/23 e CEE/89/336.
Wij verklaren als enige aansprakelijke, dat het product waarop
deze verklaring betrekking heeft, voldoet aan de volgende normen of andere normatiefve dokumenten, overeenkomstig de
bepalingen van Richtlijnen 73/23/EEC en 89/336/EEC.
Vi erklærer os eneansvarlige for, at dette produkt, som denne
deklaration omhandler, er i overensstemmelse med den
følgende standarder eller andre normative dokumenter i følge
bestemmelserne i direktivene 73/23/EEC og 89/336/EEC.
Vi deklarerar härmed värt fulla ansvar för att den produkt till
vilken denna deklaration hänvisar är i överensstämmelse med
standarddokument, eller andra normativa dokument som
framstölls i Direktiv 73/23/EEC och 89/336/EEC.
For Australia
THIS APPARATUS MUST BE EARTHED.
To ensure safe operation the three-pin plug supplied must be inserted
only into a standard three-pin power point which is effectively earthed
through the normal household wiring. Extension cords used with the
equipment must be three-core and be correctly wired to provide connection to earth. Wrongly wired extension cords are a major cause of
fatalities.
The fact that the equipment operates satisfactorily does not imply that
the power point is earthed and that the installation is completely safe.
For your safety, if in any doubt about the effective earthing of the power
point, consult a qualified electrician.
Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä
ilmoitus koskee, noudattaa seuraavia standardeja tai muita
ohjeellisia asiakirjoja, jotka noudattavat direktiivien 73/23/EEC
ia 89/336/EEC. säädöksiä.
Vi erklærer oss alene ansvarlige for at produktet som denne
erklæringen gjelder for, er i overensstemmelse med følgende
normer eller andre normgivende dokumenter som fælger
bestemmelsene i direktiven 73/23/EEC og 89/336/EEC.
-3-
ENGLISH
CONTENTS
PREFACE
Panasonic's WV-CPR460 (WV-CPR464E) series colour
digital camera introduces a new level of high picture
quality and high resolution through the use of a 1/3inch interline transfer CCD image sensor having 753
horizontal pixels (picture elements), and digital signal
processing LSIs. This model offers cutting-edge technology for advanced video surveillance.
FEATURES
1. The following functions are built in.
(1) Auto Light Control (ALC)/Electronic Light
Control (ELC)
(2) The SUPER-D2 function eliminates interference by strong background lighting which
makes the camera picture dark, such as a
spotlight.
Dynamic range of 48 dB.
(3) Various External Sync Functions, including
Gen-Lock
(4) Auto/Manual White Balance Function
(5) Electronic Shutter Function
2. Signal-to-noise ratio of 50 dB
3. Minimum illumination of 0.8 lx (0.08 footcandle)
with F 1.4 lenses.
4. Minimum illumination of 0.4 lx (0.04 footcandle)
with Panasonic aspherical high speed (F0.75)
lenses.
5. 480 lines of horizontal resolution
6. High quality picture:
(a) 2H type vertical enhancer for greater picture
sharpness
(b) Chroma averaging circuit for better colour signal-to-noise ratio
(c) Minimum of aliasing on fine objects
(d) Expanded dynamic range by use of knee circuit
(e) Highlight aperture correction for greater picture detail of bright objects
7. Ability to shoot indoor scenes with fixed iris lens by
use of Electronic Light Control (ELC) function.
8. Selectable electronic sensitivity enhancing modes
including AUTO, MANUAL and OFF
9. Built in Digital Motion Detector
10. RS485 site communication (Full-Duplex/HalfDuplex) is available.
-4-
PRECAUTIONS
1. Do not attempt to disassemble the camera.
To prevent electric shock, do not remove screws
or covers.
There are no user serviceable parts inside. Ask a
qualified service person for servicing.
5. Clean the CCD faceplate with care.
Do not clean the CCD with strong or abrasive
detergents. Use lens tissue or a cotton tipped
applicator and ethanol.
6. Never face the camera towards the sun.
Do not aim the camera at bright objects. Whether
the camera is in use or not, never aim it at the sun
or other extremely bright objects. Otherwise,
blooming or smear may be caused.
2. Handle the camera with care.
Do not abuse the camera. Avoid striking, shaking,
etc. The camera could be damaged by improper
handling or storage.
3. Do not expose the camera to rain or moisture,
or try to operate it in wet areas.
Turn the power off immediately and ask a qualified
service person for servicing. Moisture can damage the camera and also create the danger of
electric shock.
7. Do not operate the camera beyond the
specified temperature, humidity or power
source ratings.
Use the camera under conditions where temperature is between –10 °C to +50 °C (14 °F to 122 °F),
and humidity is below 90 %. The input power
source is 220 V to 240 V AC 50 Hz for WV-CPR460
and DC 12 V/AC 24 V for WV-CPR464E.
4. Do not use strong or abrasive detergents when
cleaning the camera body.
Use a dry cloth to clean the camera when dirty.
In case the dirt is hard to remove, use a mild
detergent and wipe gently.
-5-
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
q
w e
r
<WV-CPR460>
220-240V ~ 50Hz
RS485
B
A
B
A
T
R
VIDEO OUT
!5
G
!7
GEN-LOCK
Super Dynamic
WV-
!4
LOCK
!6
t
!1
<WV-CPR464E>
i
RS485
!2
!3
Hi-Z-G/L 75Ω
RS485
Hi-Z-LINE TERM
4-LINE-2-LINE
u
DC 12V
IN
AC 24V
IN
B
A
B
A
T
R
!8
o
y
1
2
GND
!0
VIDEO OUT
!5
G
GEN-LOCK
!4
!6
Slide the panel to the left until it locks.
-6-
q Auto Iris Lens Connector
This connector is used to connect the auto iris lens
with a 4-pin male connector supplied as a standard accessory (Part No. YFE4191J100).
i Up Button (J)
This button is used to move the cursor upward. It
is also used to select items in the CAM SET UP
menu.
w Focus Fixing Screw
o Right Button (M)
This button is used to move the cursor to the right.
It also selects the mode and can be used to adjust
some levels.
e Flange-back Adjusting Ring
This ring is used to adjust the back focal length or
picture focus. Rotate this ring clockwise for a Cmount lens or counterclockwise for a CS-mount
lens.
!0 Set Button (I)
This button is used to activate an item selected in
the CAM SET UP menu.
r Lens (Option)
!1 Gen-lock Termination Switch (Hi-Z, G/L 75 Ω)
Set this switch to Hi-Z when a gen-lock video input
signal is looped through. In all other cases, set
this switch to 75 Ω.
t Camera Mounting Screw Hole
This hole is used to mount the camera onto a
mounting bracket.
y Down Button (K)
This button is used to move the cursor downward.
It is also used to select items in the CAM SET UP
menu.
!2 RS485 Termination Switch
(Hi-Z – RS485 LINE TERM)
This switch is used to terminate the RS485 terminal.
Normally keep it in
Hi-Z – RS485
LINE TERM
RS485 LINE TERM
position.
u Left Button (L)
This button is used to move the cursor to the left.
It also selects the mode and can be used to adjust
some levels.
-7-
!3 Half-Duplex/Full Duplex Selection Switches
(2-LINE-4-LINE)
These triple switches are used to select either
Half-duplex (left side) or Full-duplex (right side) for
the communication lines.
!8 AC/DC Compatible Input Terminal
(DC 12 V IN/AC 24 V IN)
This terminal is for connecting the 12 V DC or 24 V
AC power supply cord.
!4 Gen-lock Input Connector (GEN-LOCK)
This connector is used to connect an external system for synchronization.
Cautions:
Connect to 12 V DC (10.8 V to 16 V) or 24 V AC
(19.5 V to 28 V) class 2 power supply only.
Make sure to connect the grounding lead to the
GND terminal when the power is supplied from a
24 V AC power source.
!5 Video Output Connector (VIDEO OUT)
This connector is used to connect the VIDEO IN
connector of the monitor.
!6 RS485 Terminals
(RS485, T(A)/T(B)/R(A)/R(B)/GND)
These terminals are used for RS485 site communication. Connect RS485 cables to these terminals.
!7 AC Inlet Socket
This socket is used to connect the power cord
(supplied as a standard accessory).
-8-
CONNECTIONS
Resistance of copper wire [at 20°C (68°F)]
A. WV-CPR460 (220 V to 240 V AC 50 Hz)
1. Plug the AC power cord (supplied as standard
accessory) into the AC Inlet Socket.
2. Connect the AC power cord to a 220 V to 240 V
AC 50 Hz outlet.
Notes:
• Connect the power cord firmly.
• The power cord should be long enough for panning and tilting.
If the cable is too short, the power cord plug may
be pulled off the camera when the camera pans or
tilts.
Copper wire
size (AWG)
Resistance
Ω/m
0.078
0.050
0.030
0.018
Resistance
Ω/ft
0.026
0.017
0.010
0.006
• Calculation of maximum cable length between
camera and power supply
10.8 V DC ≤ VA - (R x 0.42 x L) ≤ 16 V DC
L : Cable length (m)
R : Resistance of copper wire (Ω/m)
VA : DC output voltage of power supply unit
B. WV-CPR464E (12 V DC/24 V AC)
The WV-CPR464E has an AC/DC compatible input terminal. The 12 V DC or 24 V AC power supply cord can
be connected to this terminal. The camera detects the
power source automatically.
1. 12 V DC Power Supply
Connect the power
cord to the AC/DC
compatible input terminal on the rear panel of
the camera.
#24
#22
#20
#18
(0.22 mm2) (0.33 mm2) (0.52 mm2) (0.83 mm2)
L standard =
L minimum =
DC 12V
IN
AC 24V
IN
L maximum =
1
2
GND
12 V DC
(10.8 V to 16 V)
-9-
VA − 12
0.42 x R
VA − 16
0.42 x R
VA − 10.5
0.42 x R
(m)
(m)
(m)
2. 24 V AC Power Supply
Connect the power cable to the AC/DC compatible
input terminal on the rear panel of the camera.
DC 12V
IN
Video Cable
1. It is recommended to use a monitor whose resolution is at least equal to that of the camera.
2. The maximum extensible coaxial cable length
between the camera and the monitor is shown
below.
AC 24V
IN
1
2
Type of
coaxial cable
24 V AC, 60 Hz
(19.5 V to 28 V)
GND
Recommended
maximum
cable length
Recommended wire gauge sizes for 24 V AC line.
Copper wire
size (AWG)
Length
of Cable
(Approx.)
#24
#22
#20
#18
(0.22 mm2) (0.33 mm2) (0.52 mm2) (0.83 mm2)
(m)
95
150
255
425
(ft)
314
495
842
1 403
-10-
RG-59/U
(3C-2V)
RG-6/U
(5C-2V)
RG-11/U
(7C-2V)
RG-15/U
(10C-2V)
(m)
250
500
600
800
(ft)
825
1 650
1 980
2 640
RS485 Terminal
Control data is transmitted and received to and from
other peripherals.
RS485 Setting
Follow the procedures as below.
1. Slide the panel to the left until it locks.
2. Set RS485 Termination Switch to LINE TERM for
the furthermost camera from the RS232C/RS485
converter and Hi-Z for the other camera.
Initial factory setting is LINE TERM.
Switch
Position
RS485 Termination Switch (BP 1)
Function
LINE TERM
Termination ON
Hi-Z
Hi-Z
Notes:
• Shielded, two twisted pairs cable
• Low impedance
• Wire gauge size is thicker than
(0.33 mm2)
● Internal Diagram
<Full duplex>
3. Select protocol by sliding triple Half-Duplex/Full
Duplex Selection Switches simultaneously.
Initial factory settings are 4-line.
Switch
Position
BP 2
BP 3
BP 4
Function
Right
Right
Right
Full duplex (4-line)
Left
Left
Left
Half duplex (2-line)
AWG#22
Data Transmission
T (B)
T (A)
Data Reception
R (B)
R (A)
GND
<Half duplex>
BP1
BP2
BP3
BP4
Notes:
• BP stands for Bit Position.
• Daisy chain connection is not available for full
duplex.
Data Transmission
T (B)
T (A)
Data Reception
R (B)
R (A)
GND
-11-
SYSTEM CONNECTION
A) Single Camera Connection (RS485 Interface
Model/Full Duplex, Half Duplex)
B) Daisy-chain Connection (RS485 Interface
Model/Half Duplex)
SIGNAL
MONITOR
MONITOR
QUAD UNIT
SIGNAL
DATA
DATA
Super Dynamic
Super Dynamic
LOCK
WV-CPR460
LOCK
WV-CPR460
Set the RS485 Termination
Switch to Hi-Z.
RS485/
RS232C
Set the RS485 Termination
Switch to LINE TERM.
Super Dynamic
LOCK
WV-CPR460
RS485/
RS232C
Set the RS485 Termination
Switch to Hi-Z.
PC
Super Dynamic
LOCK
WV-CPR460
Set the RS485 Termination
Switch to Hi-Z.
WV-CPR460
Super Dynamic
LOCK
Set the RS485 Termination Switch to LINE TERM
-12-
PC
FOCUS OR FLANGE-BACK ADJUSTMENT
The following adjustment should be made by qualified
service personnel or system installers.
Focusing of
CS-mount lens
Focusing of
C-mount lens
1. Loosen the screw on the side of the camera.
2. Turn the flange-back adjusting ring to the desired
position.
Flange-back
Adjusting Ring
Caution: When the C-mount lens is mounted, do
not rotate the ring counterclockwise by force
after it stops. If the ring is rotated by force,
the inner lens or CCD image sensor may be
damaged.
Screw
3. Tighten the screw on the side of the camera.
Caution: Tightening the screw by force will cause
damage to the screw or deviation of focus.
-13-
Installation of Auto Iris Lens Connector
Mounting the Lens
Install the lens connector (YFE4191J100) when using a
video drive ALC lens.
The installation should be made by qualified service personnel or system installers.
(1) Cut the iris control cable at the edge of the lens
connector to remove the existing lens connector
and then remove the outer cable cover as shown
in the diagram below.
The pin assignment of the lens connector is as follows:
Pin 1: Power source; +9 V DC, 50 mA max.
Pin 2: Not used
Pin 3: Video signal; 1.3 V[p-p]/40 kΩ
Pin 4: Shield, ground
Caution:
Before you mount the lens, loosen the screw on
the side of the camera, and rotate the flange-back
adjusting ring clockwise until it stops. If the ring is
not at the end, the inner glass or CCD image sensor may be damaged.
1. Mount the lens by turning it clockwise on the lens
mount of the camera.
2. Connect the lens cable to the auto iris lens connector on the side of the camera.
Screw
q
(2) Solder the lens cable to the pins of the supplied
connector.
Pin 3
Rib
w
Pin 1
Pin 4
Flange-back
Adjusting Ring
Pin 2
-14-
Caution for Mounting the Lens
The lens mount should be a C-mount or CS-mount (1”32UN) and the lens weight should be less than 450 g
(0.99 lbs). If the lens is heavier, both the lens and
camera should be secured by using the supporter.
The protrusion at the rear of the lens should be as
shown below:
C-mount: Less than 13 mm (1/2”)
CS-mount: Less than 8 mm (5/16”)
-15-
INSTALLATION OF CAMERA
• Mounting from the top
Remove the mount adapter from the bottom of the
camera by removing the two fixing screws. Attach
the mount adapter to the top as shown in the diagram, then mount the camera on the mounting
bracket.
Make sure that the two original fixing screws are
used when mounting the mount adapter as longer
length screws may damage inner components.
Fixing Screws
Mount Adapter
-16-
SETUP
1. CAMRA SETUP MENU
2. SETUP OPERATION
This camera utilizes a user setup menu that is displayed on-screen.
This camera utilizes a user Setup menu (CAM SET UP
or RS485 SET UP) that is displayed on the monitor.
To set items on these menus, use the following buttons
on the side panel.
• Opening the Setup Menu
Press and hold down I for 2 seconds or more.
Up
Button
Left Button
Right
Button
Set Button
Down
Button
↵
↵
** SET UP **
CAMERA
RS485
END
Up Button (J): Moves the cursor upwards. Use this
button to select an item or adjust the parameters.
Down Button (K): Moves the cursor downwards.
Use this button to select an item or adjust the
parameters.
Right Button (M): Moves the cursor to the right. Use
this button to select or adjust the parameters of the
selected item. The parameter changes each time
this button is pressed.
SET UP DISABLE
The SET UP menu appears on the monitor as shown
above.
Note: If no button is pressed for 6 minutes while the
SET UP menu or any other menu is opened, the
menu is automatically closed and the mode
returns to the normal camera picture.
-17-
• Editing the RS485 and CAM SET UP Menu
Left Button (L): Moves the cursor to the left. Use
this button to select or adjust the parameters of the
selected item. The parameter changes each time
this button is pressed.
Set Button (I): Executes selections and displays a
submenu for an item with N mark.
END: Close Setup menu.
RET: Return to the previous menu or page.
Important Notice:
• When the SET UP DISABLE appears on the bottom
line of the SET UP menu, you cannot change the
currently active settings. This is to prevent accidental changing of the settings.
• Set the RS485 menu previously.
** SET UP **
CAMERA
↵
• All Reset Operation
All Reset allows you to reset all setup menu items to
the factory default settings if you are unsure about the
correct settings. Proceed as follows:
(1) Make sure that the CAM SET UP menu is not displayed (a camera picture is displayed).
(2) While pressing both L and M, press I for a
few seconds. The message ALL RESET momentarily appears on the monitor.
This resets all adjustments and parameters to the
factory default settings.
** SET UP **
↵
CAMERA
END
↵
RS485
↵
To return to the SET UP menu.
Move the cursor to RET and press I. The SET UP
menu appears.
RS485
SET UP DISABLE
END
↵
↵↵
** CAM SET UP **
CAMERA ID
OFF
ALC/ELC
ALC
SHUTTER
--AGC
ON
SENS UP
OFF
SYNC
INT
WHITE BAL
ATW
MOTION DET
OFF
LENS DRIVE
DC
RET
* RS485
SET UP *
UNIT NUMBER
BAUD RATE
DATA BIT
PARITY CHECK
STOP BIT
XON/XOFF
WAIT TIME
ALARM DATA
DELAY TIME
RET
-18-
1
19200
8
NONE
1
NOT USE
OFF
AUTO2
---
SET UP ENABLE
To edit the SET UP menu (Change settings), use J
and K or L and M to move the cursor to SET UP
DISABLE in the bottom line.
Press I. SET UP DISABLE changes to SET UP
ENABLE. Move the cursor to END, then to the item(s)
you want to change. Move the cursor to CAMERA or
RS485, then press I.
Refer to the sections below for a detailed description or
menu items. If you decide not to make any changes
after checking the current settings, move the cursor to
END at the start of the bottom line, and press I to
close the SET UP menu and return to the normal camera picture mode.
• Editing the RS485 SET UP Menu
You can remote control this
fied extension unit such as
modem.
The RS485 menu is used to
press I. The RS485 SET
monitor screen.
* RS485
set the SET UP menu and
UP menu appears on the
SET UP *
UNIT NUMBER
BAUD RATE
DATA BIT
PARITY CHECK
STOP BIT
XON/XOFF
WAIT TIME
ALARM DATA
DELAY TIME
RET
Important Notice:
When the cursor is moved to END and the CAM
SET UP or RS485 menu closed after changing the
parameters, the new values are saved in the EEPROM (Electric Erasable and Programmable Read
Only Memory). These values remain valid until new
values are saved, even if the power of the camera
is off.
camera by using a specipersonal computer with a
1
19200
8
NONE
1
NOT USE
OFF
AUTO2
---
Unit Number Setting
This item lets you select the camera number for RS485
communication.
1. Move the cursor to UNIT NUMBER.
2. Select the camera number to be used with RS485
communication and press I.
The initial factory setting is 1.
-19-
Baud Rate Setting
This item is lets you select the transmission speed for
RS485 communication. (BAUD is the unit of bit per second.)
1. Move the cursor to BAUD RATE.
2. Select the 19 200, 9 600, 4 800 or 2 400 bps for
the baud rate.
The initial factory setting is 19 200 bps.
Stop Bit Setting
This item lets you select the number of stop bits for
RS485 communication.
1. Move the cursor to STOP BIT.
2. Select 1 or 2 for the number of stop bits and press I.
The initial factory setting is 1 bit.
XON/XOFF Setting
This lets you select applying the flow control or not for
RS485 communication.
1. Move the cursor to the XON/XOFF.
2. Select NOT USE (not apply flow control) or USE
(apply flow control) mode for XON/XOFF for RS485
communication and press I.
Data Bit Setting
This item lets you select the number of data bits for
RS485 communication.
1. Move the cursor to DATA BIT.
2. Select 7 or 8 bit for the number of data bits and
press I.
The initial factory setting is 8 bit.
Wait Time Setting
This item lets you select the waiting time in milli-seconds (ms) to retry after confirming that no data is
received from the controller in RS485 communication.
1. Move the cursor to the WAIT TIME parameter..
2. Select OFF, 100, 200, 400 or 1 000 ms for the wait
time.
When no transmission is needed, select OFF.
The initial factory setting is OFF (No retry).
Parity Check Setting
This item lets you select the parity bit for RS485 communication.
1. Move the cursor to PARITY CHECK.
2. Select NONE, EVEN or ODD for parity check and
press I.
The initial factory setting is NONE.
-20-
Alarm Data Setting
This item lets you select the way of transmitting the
alarm data for RS485 communication.
1. Move the cursor to the ALRAM DATA.
2. Select the alarm data transmission mode from following parameters and press I.
• Installation of Software for RS485 Communication
1. Insert the Install Disk 1 to the C drive.
2. Input command as follows.
C:\SETUP
The installation starts.
3. When the window that says “Please insert the disk
labeled: “Disk 2” into drive C:” appears on the
monitor screen, insert the Install Disk 2 and press
.
4. When the installation is completed, the window
that says “485_GUI Set up was completed successfully”. Appears on the monitor screen.
5. After installation of 485_GUI Set up is completed,
open 485_GUI Set up, and set the RS485 communication parameters.
POLLING:Transmit the alarm data to the controller
to request from the controller.
AUTO1: Transmit the alarm data each time the
alarm signal is received.
AUTO2: Transmit the alarm data 5 seconds each.
The initial factory setting is AUTO2.
Delay Time Setting
This item lets you select the lowest delay time to reply
to the reception of data in 2-line RS485 communication.
1. Move the cursor to DELAY TIME parameter.
2. Select OFF or 100 ms for the Delay time and press
I.
The initial factory setting is OFF.
Notes:
• The setting change is disabled in Full Duplex
(4-line) RS485 communication.
• The selected Full or Half Duplex Setting will
become valid after the camera has been powered up again.
-21-
SETTING PROCEDURES
4. After selecting the character, press I. The
selected character appears in the editing area.
(The pointer in the editing area moves to the right
automatically at this moment.)
5. Repeat the steps above until all characters are
edited.
1. Camera Identification (CAMERA ID)
Setting
You can use the camera identification (CAMERA ID) to
assign a name to the camera. The camera ID consists
of up to 16 alphanumeric characters. The camera ID
display can be switched on or off on the monitor
screen.
To enter a blank space in the CAMERA ID
Move the cursor to SPACE and press I.
To edit the CAMERA ID
1. Move the cursor to the CAMERA ID parameter.
2. Press I. The CAMERA ID menu appears. The
cursor on the letter “0” is highlighted.
3. Move the cursor to the character you want to edit
by pressing L/M/J/K.
To replace a specific character in the CAMERA ID
1. Move the cursor to the editing area by pressing
K.
2. Move the pointer to the character to be replaced
by pressing L or M. Then move the cursor to
the character area and select a new character.
3. Press I to determine the CAMERA ID.
Character Cursor
0123456789
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
().,'":;&#!?=
+-*/%$ÄÜÖÆÑÅ
SPACE
POSI RET END RESET
Command
................
Editing
Area
Pointer
To erase all characters in the editing area
Move the cursor to RESET and press I. All characters in the editing area disappear.
Character
Area
CAMERA ID menu
-22-
To determine the display position of the CAMERA
ID
1. Move the cursor to POSI, and press I. The display shown below appears and the CAMERA ID is
highlighted.
2. Light Control Setting (ALC/ELC)
You can select the light control mode according to the
lens type.
ALC: If you use the auto iris lens, select this parameter.
ELC: If you use a fixed or manual iris lens, select this
parameter.
Highlighted
1. Move the cursor to the ALC/ELC parameter.
2. Select ALC or ELC.
WV-CPR460
2-1. ALC Mode with SUPER-D2 ON
Super Dynamic2 Function (SUPER-D2)
The important object in a scene is usually placed in the
centre of the monitor’s screen. In SUPER-D2 mode,
more photometric weight is given to the center of the
screen (where the important object is located) than to
the edge of the picture (where a bright backlight would
most likely be located). You can use the SUPER-D2
function if you select ALC. It eliminates interference by
strong background lighting which makes the camera
picture dark, such as a spotlight.
2. Move the CAMERA ID to the desired position by
pressing L/M/J/K.
3. Press I to fix the position of the CAMERA ID.
The mode returns to the previous CAMERA ID
menu.
Notes:
• The CAMERA ID stops at the edges of the
monitor screen.
• The CAMERA ID moves faster if any of L/
M/J/K is kept pressed for a second or
more.
1. After selecting ALC, press I to open the ALC
CONT menu.
2. Move the cursor to the SUPER-D2 parameter and
select ON.
-23-
1. Move the cursor to the SUPER-D2 parameter and
select OFF. (When you select ELC, SUPER-D2 is
not available.) The item MASK SET appears on the
menu.
** ALC CONT **
BACK LIGHT COMP
MASK SET
LEVEL
RET
OFF
↵
SUPER-D2
...I.....
+
** ALC CONT **
BACK LIGHT COMP
END
MASK SET
3. If you want to adjust the video output level, move
the cursor to the “I” position. Adjust to the desired
level by pressing L or M.
LEVEL
RET
ON
LEVEL
...I.....
+
RET
...I.....
+
END
2. Move the cursor to MASK SET and press I. 48
mask areas appear on the monitor screen. The
cursor is blinking in the upper left corner of the
screen.
** ALC CONT **
BACK LIGHT COMP
SUPER-D2
OFF
↵
SUPER-D2
Blinking
END
2-2. ALC Mode with SUPER-D2 OFF and ELC
Mode
Note: If ELC is selected, set MASK SET according to
this procedure.
-24-
5. After masking is completed, press I for 2 seconds or more. The ALC CONT menu appears.
6. If you want to change the video output level (picture contrast), move the “I” cursor for LEVEL and
adjust the level.
3. Move the cursor to the area where backlight is
bright and press I to mask that area. The mask
turns to white. (When the cursor is moved on an
area that has already been masked, the mask and
cursor start blinking.)
Note: If ON is selected for the SUPER-D2 parameter, a
shadow (black line) may appear at the boundary
between the bright and the dim scene. This is a
natural phenomenon and does not indicate trouble.
Blinking
4. Repeat step 3 to mask the desired area. To cancel masking, move the cursor to that area and
press I.
Turns to white
Blinking
-25-
3. Shutter Speed Setting (SHUTTER)
4. Gain Control Setting (AGC ON/OFF)
Note: When ELC is selected for ALC/ELC on the CAM
SET UP menu or ON is selected for SUPER-D2 on
the ALC CONT menu, this item is not available.
To select electronic shutter speed, select OFF for
SUPER-D2 in the ALC CONT menu.
You can set the gain (brightness level portion of an
image) to automatic level adjustment (ON) or fixed
level (OFF).
Move the cursor to the AGC parameter and select
automatic level adjustment (ON) or fixed level (OFF).
Move the cursor to the SHUTTER parameter and select
the electronic shutter speed.
The preset values for SHUTTER (electronic shutter
speed) change by pressing L or M as shown at
below:
Note: If ON is selected for the AGC parameter, the
noise reduction function is automatically activated
under low light conditions to reduce noise. In pictures containing a moving object, this may result in
an afterimage.
OFF (1/50)
1/10 000
1/120
1/4 000
1/250
1/2 000
1/500
1/1 000
-26-
Notes:
• When ON is selected for SUPER-D2 in the ALC
CONT menu, FIX is not available for this item.
• When you select AUTO for SENS UP and ON for
SUPER-D2, the SENS UP function has priority so
that the SUPER-D2 function is not activated automatically.
• While the SENS UP function is selected, noise,
spots or a whitish phenomenon may appear in the
picture when the sensitivity of the camera is
increased. This is a normal phenomenon.
5. Electronic Sensitivity Enhancement
(SENS UP)
There are two modes for SENS UP.
AUTO: If you select X10 AUTO, for example, the
sensitivity is raised automatically to X10 max.
When AUTO is selected, AGC is automatically
set to ON.
FIX: If you select X32 FIX, for example, the sensitivity is raised to just X32.
Move the cursor to the SENS UP parameter and select
the parameter for electronic sensitivity enhancement.
The preset values for SENS UP (electronic sensitivity
enhancement) change by pressing L or M as
shown right:
OFF
X32 FIX
X2 AUTO
X16 FIX
X4 AUTO
X10 FIX
X6 AUTO
X6 FIX
X10 AUTO
X4 FIX
OFF
X2 FIX
-27-
Important Notice:
1. The priority for the sync modes is as follows:
1. Multiplexed Vertical Drive (VD2) (Highest priority)
2. Line-lock (LL)
3. Colour Composite Video or Blackburst Signal
(VBS)
4. B/W Composite Video or Composite Sync
Signal (VS)
5. Internal Sync (INT) (Lowest priority)
2. When the internal sync mode is to be used, select
INT. No gen-lock input signal should be supplied
to the Gen-lock Input Connector on the rear panel.
3. Whenever the multiplexed vertical drive pulse
(VD2) is supplied to the camera from an external
equipment such as a Matrix Switcher, the camera
sync mode is automatically switched to the VD2
mode.
4. When the VBS or VS gen-lock mode is to be used
select INT from this menu and supply the gen-lock
input signal to the Gen-lock Input Connector on
the rear panel.
5. The VBS gen-lock mode has a submenu for horizontal and subcarrier phase adjustments. When
the cable length of the video output or the genlock input is changed, the horizontal and subcarrier phase must be re-adjusted.
6. The VS gen-lock mode has a submenu for horizontal phase adjustments. When the cable length of
the video output or the gen-lock input is changed,
the horizontal phase must be re-adjusted.
6. Synchronization Setting (SYNC)
You can select internal sync mode (INT) or line-lock
mode (LL). Additionally, this model accepts the VBS
signal (colour composite video or blackburst signal)
and VS signal (B/W composite video or composite
sync signal). The VD2 signal (multiplexed vertical
drive signal) with the composite video output signal
from external equipment such as a Matrix Switcher is
also acceptable.
Whenever the VD2 signal is supplied to this camera,
the camera automatically switches to the VD2 sync
mode.
1. Move the cursor to the SYNC parameter and
select line-lock (LL) or internal (INT).
2. Press I.
If LL is selected, the SYNC menu appears. (If INT
is selected, the synchronization mode is automatically set to internal sync pulse, and the menu is
not displayed.)
-28-
4. After confirming that the cursor is on EXT (VBS),
press
. The phase adjustment menu appears
on the monitor.
5. Supply the video output signal of the camera to be
adjusted and the reference gen-lock input signal
to a dual-trace oscilloscope.
6. Set the oscilloscope to the horizontal rate and
expand the horizontal sync portion on the oscilloscope.
7. The line-lock mode has a submenu for line-lock
vertical phase adjustment. If the camera installation is relocated, check the vertical phase adjustment again since the AC line phase may be different.
6-1. VBS Gen-lock Mode (EXT (VBS))
1. Move the cursor to the SYNC parameter and
select INT.
2. Connect the coaxial cable for the blackburst or
composite colour video signal to the gen-lock
input connector.
3. Confirm that the INT parameter changed to EXT
(VBS) on the menu.
Caution: The gen-lock input signal should meet
the CCIR specifications and should not contain jitter, such as a VTR playback signal, as it
could disturb synchronization.
SC COARSE
SC FINE
RET
........I
+
1(1--4)
....I....
+
END
7. Move the cursor to H PHASE.
8. Adjust the horizontal phase by pressing L or
M. The adjustable range is 0 to 2.0 µs.
9. Move the cursor to SC COARSE.
↵
↵
↵↵
** CAM SET UP **
CAMERA ID
OFF
ALC/ELC
ALC
SHUTTER
--AGC
ON
SENS UP
OFF
SYNC
EXT(VBS)
WHITE BAL
ATW
MOTION DET
OFF
LENS DRIVE
DC
** SYNC **
H PHASE
RET
-29-
10. Press L or M to match the chroma phase of
the camera’s video signal, when observed at the
output of the special effects generator (SEG) or
Switcher, as closely as possible to the colour of
the original scene. (SC COARSE adjustment can
be incremented in steps of 90 degrees (4 steps)
by pressing L or M.)
Note: After the fourth step, the adjustment returns
to the first step.
11. Move the cursor to SC FINE.
12. Press L or M to match the colour (hue) of the
camera’s video signal, when observed at the output of the special effects generator (SEG) or
Switcher, as closely as possible to the colour of
the original scene.
The SC FINE adjustment has a range of 90
degrees of colour shift.
Notes:
• When the “I” cursor reaches the “+” end, it
jumps back to “–” . At the same time, SC
COARSE is incremented by one step to
enable a continuous adjustment. The reverse
takes place when the “I” cursor reaches the
“–” end.
• When L or M is kept pressed for a second
or more, the “I” cursor moves faster.
• For more accurate adjustment, supply both
the original camera video output signal and
the effect output video signal (program output
video signal) of the special effects generator
(SEG) to a vectorscope and compare the
chroma phase of both signals.
• To reset SC COARSE and SC FINE to the values preset at the factory, press L or M
simultaneously. SC COARSE and SC FINE
adjustment are reset to the factory setting.
1 (1 - - 4): 0 degrees
2 (1 - - 4): 90 degrees
3 (1 - - 4): 180 degrees
4 (1 - - 4): 270 degrees
-30-
6. Set the oscilloscope to the horizontal rate and
expand the horizontal sync portion on the oscilloscope.
7. Move the cursor to H PHASE.
8. Adjust the horizontal phase by pressing L or
M. The adjustable range is 0 to 2.0 µs.
6-2. VS Gen-lock Mode (EXT (VS))
1. Move the cursor to the SYNC parameter and
select INT.
2. Connect the coaxial cable for the composite sync
or composite B/W video signal to the gen-lock
input connector.
3. Confirm that the parameter INT changed to EXT
(VS) on the menu.
Caution: The gen-lock input signal should meet
the CCIR specifications and should not contain jitter, such as a VTR playback signal, as it
could disturb synchronization.
** SYNC **
H PHASE
RET
↵
↵
↵↵
** CAM SET UP **
CAMERA ID
OFF
ALC/ELC
ALC
SHUTTER
OFF
AGC
ON
SENS UP
OFF
SYNC
EXT(VS)
WHITE BAL
ATW
MOTION DET
OFF
LENS DRIVE
DC
END
SET UP ENABLE
4. After confirming that the cursor is on EXT (VS),
press I. The phase adjustment menu appears
on the monitor.
5. Supply the video output signal of the camera to be
adjusted and the reference gen-lock input signal
to a dual-trace oscilloscope.
-31-
END
........I
+
6. Press L or M to match the vertical phase for
both video output signals as closely as possible.
(COARSE adjustment can be incremented in 16
steps by 22.5 degrees by pressing L or M.)
Note: After the sixteenth step, the adjustment
returns to the first step.
6-3. Line-lock Sync Mode (LL)
Note: The line-lock (LL) sync mode is not available
when the camera operates on DC power.
1. Move the cursor to the SYNC parameter and
select LL.
Note: The settings in this menu can be made only
when the multiplexed vertical drive signal
(VD2) is not supplied to the camera.
2. After confirming that the cursor is on LL, press
I. The vertical phase adjustment menu appears
on the monitor.
3. Supply the video output signal of the camera to be
adjusted and the reference camera video output
signal to a dual-trace oscilloscope.
1 (1 - - - 16): 0 degree
2 (1 - - - 16): 22.5 degrees
16 (1 - - - 16): 337.5 degrees
7. Move the cursor to FINE.
8. Press L or M to match the vertical phase for
both video output signals as closely as possible.
(FINE adjustment can be made up to 22.5 degrees
by pressing L or M.)
Notes:
• When the “I” cursor reaches the “+” end, it
jumps back to “–”. At the same time, COARSE
is incremented by one step to enable a continuous adjustment. The reverse takes place
when the “I” cursor reaches the “–” end.
• When L or M is kept pressed for a second
or more, the “I” cursor moves faster.
** SYNC **
V PHASE
COARSE
FINE
RET
1(1--16)
I........
+
END
4. Set the oscilloscope to the vertical rate and
expand the vertical sync portion on the oscilloscope.
5. Move the cursor to COARSE.
-32-
3. When the scene is dim.
In these cases, select the AWC mode.
Move the cursor to the WHITE BAL parameter and
select ATW. The white balance of the camera is
automatically set.
• To reset COARSE and FINE to the values preset at the factory, press L or M simultaneously. COARSE and FINE adjustments are
preset at the factory to zero-crossing of the
AC line phase.
• If the AC line contains noise (spike noise,
etc.), the stability of the vertical phase of the
camera video output signal may be disturbed.
• Automatic White Balance Control Mode (AWC)
In this mode, accurate white balance is obtained
within a colour temperature range of approximately 2 300 to 10 000K.
7. White Balance Setting (WHITE BAL)
↵↵
** CAM SET UP **
CAMERA ID
OFF
ALC/ELC
ALC
SHUTTER
OFF
AGC
ON
SENS UP
OFF
SYNC
INT
WHITE BAL
AWC→PUSH SW
MOTION DET
OFF
LENS DRIVE
DC
7-1. Auto-Tracing White Balance Mode (ATW)
You can select one of two modes for white balance
adjustment as follows:
• ATW (Auto Tracing White Balance)
In this mode, the colour temperature is monitored
continuously and thereby white balance is set
automatically. The colour temperature range for
the proper white balance is approximately 2 600 6 000K. Proper white balance may not be obtained
under the following conditions:
1. The colour temperature is out of the 2 600 6 000K range.
2. When the scene contains mostly high colour
temperature objects, such as a blue sky or
sunset.
END
SET UP ENABLE
1. Move the cursor to the WHITE BAL parameter and
select AWC → PUSH SW.
2. Press I to start the white balance setup. The
PUSH SW is highlighted to indicate that the white
balance is being set.
3. When the white balance setting is completed, the
PUSH SW returns to normal display.
-33-
Note: In case that the white balance is not set, the
PUSH SW Is being highlighted.
Fine Adjustment for AWC (ATW) Manually
You can add the detailed setting for white balance setting manually.
1. To set MASK SET, proceed as described in steps
2 to 4 of “ALC mode with SUPER-D2 OFF and ELC
mode”.
2. Move the cursor to R.
3. Press L or M to obtain the optimum amount of
red gain.
4. Move the cursor to B.
5. Press L or M to obtain the optimum amount of
blue gain.
Note: When you need to set MASK SET, re-adjust to
obtain the optimum amount of red and blue gain.
4. When you want to adjust the white balance manually, press M to select AWC and press I. The
AWC menu appears on the monitor. (When ATW is
selected, pressing I displays the ATW menu.)
**
AWC
R
MASK SET
↵
B
RET
**
....I....
+
....I....
+
END
-34-
4. Move the cursor to the ALARM parameter and
select ON or OFF to set the alarm for DISPLAY
MODE.
Note: When the system controller WV-RM70, WVCU550, WV-CU550A, or WV-CU151 is used
with this model, select OFF for ALARM.
5. Move the cursor to DISPLAY MODE and press I
to see the current setting. The masks that detect
the brightness changes start blinking.
6. To raise detection sensitivity, press I to return
to the MOTION DETECT menu.
7. To obtain the optimum detection level, move the
“I” cursor to adjust the level.
8. Repeat the procedures above to obtain a satisfactory setting.
8. Motion Detector Setting (MOTION DET)
The motion detector detects the moving objects in the
scene by monitoring changes in brightness level. You
can select the level of sensitivity for motion detection.
When this camera is connected to a compatible intelligent CCTV system, the camera transmits an alarm signal by multiplexing it with the video signal.
1. Move the cursor to the MOTION DET parameter
and select ON.
2. Press I. The MOTION DETECT menu appears
on the monitor screen.
** MOTION DETECT **
....I....
+
DISPLAY MODE
RET
ON
↵
ALARM
MASK SET
Notes:
• Masking or adjusting the detection level is needed
to prevent malfunction under the following conditions:
• When shooting an object under flickering fluorescent light or shooting in ELC.
• When leaves or curtains etc. are swayed by the
wind.
• When the object is lighted by lighting equipment
that constantly turns on and off.
• It takes about 0.2 seconds for the alarm signal to
reach the alarm terminal of the VTR after the camera detects the object.
↵
LEVEL
END
3. Move the cursor to MASK SET and press I.
MASK SET lets you set 48 mask areas. To set
MASK SET, proceed as described in steps 2 to 4
of “ALC mode with SUPER-D2 OFF and ELC
mode”.
-35-
Because the alarm signal is multiplexed on the
video signal, it may be mistakenly interpreted by
other video equipment as a time code signal.
Therefore, when the camera is not used in a
Panasonic Intelligent CCTV System select OFF to
prevent the above from occurring.
• To confirm the changed parameter of Alarm Data
Setting on the RS485 Setup menu for DISPLAY
MODE, move the cursor to RET to return to the
previous menu and move the cursor to END to
close the menu once.
10. Special Menu
This menu lets you adjust and setup the video signal of
the camera to meet your requirements.
Move the cursor to RET on the bottom line of the CAM
SET UP menu and press L or M simultaneously
(holding down L and press M) for 2 seconds or
more. The SPECIAL menu appears on the monitor as
shown at right.
↵↵
** CAM SET UP **
CAMERA ID
OFF
ALC/ELC
ALC
SHUTTER
--AGC
ON
SENS UP
OFF
SYNC
INT
WHITE BAL
ATW
MOTION DET
OFF
LENS DRIVE
DC
OFF
....I....
....I....
.I.......
+
CAMERA RESET
PUSH SW
↵
9. Lens Drive Signal Selection (LENS DRIVE)
** SPECIAL **
UP SIDE DOWN
CHROMA GAIN
AP GAIN
PEDESTAL
This item is used to select the type of auto iris lens
drive signal to be supplied to the lens from the auto iris
lens connector.
RET
END
RET
1. Move the cursor to the LENS DRIVE parameter.
2. Select DC if you are using the auto iris lens that
requires a DC drive signal.
Select VIDEO if you are using the auto iris lens that
requires a video drive signal.
10-1. Camera Picture Upside Down Positioning
(UP SIDE DOWN)
1. Move the cursor to the UP SIDE DOWN parameter.
2. Select ON when you want to turn the picture
upside down.
-36-
10-2. Chroma Level Setting (CHROMA GAIN)
1. Move the cursor to the CHROMA GAIN parameter.
2. While observing the vectorscope or colour video
monitor, move the “I” cursor to adjust the chroma
level.
10-3. Aperture Gain Setting (AP GAIN)
1. Move the cursor to the AP GAIN parameter.
2. While observing the wave form monitor or colour
video monitor, move the “I” cursor to adjust the
aperture gain level.
10-4. Pedestal Level Setting (PEDESTAL)
1. Move the cursor to the PEDESTAL parameter.
2. While observing the wave form monitor or colour
video monitor, move the “I” cursor to adjust the
pedestal level (black level).
To reset to the factory settings (CAMERA RESET)
1. Move the cursor to the CAMERA RESET parameter. PUSH SW is highlighted.
2. While holding down L or M, press I for 2
seconds or more. The camera is reset to the factory settings.
-37-
SPECIFICATIONS
Pick-up Device:
Scanning Area:
Scanning:
Horizontal:
Vertical:
Synchronization:
Video Output:
Horizontal Resolution:
Signal-to-Noise Ratio:
Dynamic Range:
Minimum Illumination:
Gain Control:
White Balance:
Aperture:
Electronic Light Control:
Super Dynamic2:
Electronic Shutter Speed:
Lens Mount:
ALC Lens:
Ambient Operating Temperature:
Ambient Operating Humidity:
Power Source and
Power Consumption:
753 (H) x 582 (V) pixels, Interline Transfer CCD
4.8 (H) x 3.6 (V) mm (Equivalent to scanning area of 1/3” pick-up tube)
625 lines/50 fields/25 frames
15.625 kHz
50 Hz
Internal, Line-locked, External (VS/VBS) or
Multiplexed Vertical Drive (VD2) selectable
1.0 V[p-p] PAL composite 75 Ω/BNC connector
480 lines
50 dB (AGC OFF, weight ON)
48 dB
0.4 lx (0.04 footcandle) at F0.75 [Equivalent to 0.8 lx (0.08 footcandle) at F1.4]
AGC ON or OFF (SET UP MENU) selectable
ATW or AWC (SET UP MENU) selectable
Set Variable (SET UP MENU)
Equivalent to continuous variable shutter speeds between 1/50 s and 1/10 000 s
ON or OFF (SET UP MENU) selectable
1/50 (OFF), 1/120, 1/250, 1/500, 1/1 000,1/2 000,
1/4 000, 1/10 000 s selectable
C-mount or CS-mount selectable
DC or Video selectable
–10 °C to +50 °C (14 °F to 122 °F)
Less than 90 %
WV-CPR460:
220 V to 240 V AC 50 Hz, 5.6 W
WV-CPR464E: 24 V AC 50 Hz, 5.2 W
12 V DC, 520 mA
-38-
Dimensions (without lens):
Weights (without lens):
74 (W) x 55 (H) x 123 (D) mm
[2-15/16” (W) x 2-3/16” (H) x 4-13/16” (D)]
WV-CPR460: 0.42 kg (0.9 lbs.) (without power cord)
WV-CPR464E: 0.41 kg (0.9 lbs.)
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.
STANDARD ACCESSORIES
Body Cap.....................................................................1 pc.
ALC Lens Connector (YFE4191J100)..........................1 pc.
AC Power Cord (only WV-CPR460/G) .........................1 pc.
Floppy Disk..................................................................2 pcs.
OPTIONAL ACCESSORIES
Lenses :
WV-LA2R8C3B, WV-LA4R5C3B, WV-LA9C3B, WV-LA210C3, WV-LA408C3 WV-LA908C3,
WV-LZ61/10, WV-LZ61/15, WV-LZ62/2, WV-LZ62/8, WV-LF4R5C3A, WV-LF9C3A, WV-LZF61/2
-39-
Matsushita Electric Industrial Co., Ltd.
Web Site : http://www.panasonic.co.jp/global/
N0600-2042
2001
© Matsushita Communication Industrial Co., Ltd. All rights reserved.
V8QA5550CN
N 19
Printed in Japan
Inprimé au Japon
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement