LUM Beverly Sport Touring ABS-ASR
PIAGGIO WOULD LIKE TO THANK YOU
for choosing one of its products. We have prepared this manual to help you to get the very best from your vehicle. Please read it carefully before riding
the vehicle for the first time. It contains information, tips and precautions for using your vehicle. It also describes features, details and devices to assure
you that you have made the right choice. We believe that if you follow our suggestions, you will soon get to know your new scooter and it will serve you
well for a long time to come. This booklet forms an integral part of the vehicle; should the vehicle be sold, it must be transferred to the new owner.
LUM Beverly Sport Touring ABS-ASR
Ed. 03_05/2012
The instructions given in this manual are intended to provide a clear, simple guide to using your vehicle; this booklet also details routine maintenance
procedures and regular checks that should be carried out on the vehicle at an authorised Dealer or Service Centre. The booklet also contains
instructions for simple repairs. Any operations not specifically described in this booklet require the use of special tools and/or particular technical
knowledge: to carry out these operations, refer to any authorised Dealer or Service Centres.
2
Personal safety
Failure to completely observe these instructions will result in serious risk of personal
injury.
Safeguarding the environment
Sections marked with this symbol indicate the correct use of the vehicle to prevent damaging the environment.
Vehicle intactness
The incomplete or non-observance of these regulations leads to the risk of serious
damage to the vehicle and sometimes even the invalidity of the guarantee.
The signs that you see on this page are very important. They are used to highlight parts
of the booklet that should be read with particular care. The different symbols are used
to make each topic in the manual simple and quick to locate.
3
4
INDEX
VEHICLE......................................................................................
Dashboard................................................................................
Analogue instrument panel.......................................................
Clock.........................................................................................
Digital lcd display......................................................................
*MODE* button......................................................................
Key switch.................................................................................
Locking the steering wheel....................................................
Releasing the steering wheel................................................
Switch direction indicators........................................................
Horn button...............................................................................
Light switch...............................................................................
Start-up button..........................................................................
Engine stop button....................................................................
System ABS..............................................................................
System ASR..............................................................................
The immobilizer system............................................................
Keys......................................................................................
Immobilizer device enabled indicator led..............................
Operation...............................................................................
Programming the immobilizer system...................................
Accessing the fuel tank.............................................................
Power supply socket.................................................................
Opening the saddle...............................................................
Identification..............................................................................
Rear top box opening................................................................
Bag clip.....................................................................................
USE..............................................................................................
Checks......................................................................................
Refuelling..................................................................................
Tyre pressure............................................................................
Shock absorbers adjustment....................................................
Running in.................................................................................
7
8
9
11
13
13
13
14
14
15
15
16
16
17
17
18
23
23
24
24
25
27
27
28
28
30
31
33
34
34
36
37
38
Starting up the engine...............................................................
Precautions...........................................................................
Stopping the engine..................................................................
Stand.........................................................................................
Automatic transmission.............................................................
Safe driving...............................................................................
MAINTENANCE...........................................................................
Engine oil level..........................................................................
Engine oil level check............................................................
Engine oil top-up...................................................................
Warning light (insufficient oil pressure).................................
Engine oil change..................................................................
Hub oil level..............................................................................
Tyres.........................................................................................
Spark plug dismantlement........................................................
Removing the air filter...............................................................
Air filter cleaning.......................................................................
Cooling fluid level......................................................................
Checking the brake oil level......................................................
Braking system fluid top up...................................................
Battery.......................................................................................
Use of a new battery.............................................................
Long periods of inactivity..........................................................
Fuses........................................................................................
Lamps.......................................................................................
Front light group........................................................................
Headlight adjustment.............................................................
Front direction indicators...........................................................
Rear optical unit........................................................................
Number plate light.....................................................................
Helmet compartment lighting bulb............................................
Rear-view mirrors......................................................................
Front and rear disc brake..........................................................
5
39
40
41
41
42
43
47
48
48
49
49
50
51
53
54
55
56
57
59
59
63
64
65
66
68
70
71
72
73
74
75
75
76
Puncture....................................................................................
Periods of inactivity...................................................................
Cleaning the vehicle..................................................................
Troubleshooting........................................................................
TECHNICAL DATA......................................................................
Toolkit.......................................................................................
SPARE PARTS AND ACCESSORIES........................................
Warnings...................................................................................
SCHEDULED MAINTENANCE....................................................
Scheduled servicing table.........................................................
77
78
78
80
83
88
89
90
93
94
6
LUM Beverly Sport Touring ABSASR
Chap. 01
Vehicle
7
1 Vehicle
Dashboard (01_01)
01_01
8
B = Bag hook
C = Saddle opening button
D = Horn button
E = Turn indicator switch
F = Rear brake lever
G = Light switch with passing
H = Instrument panel
I = Emergency stop switch RUN-OFF
L = Front brake lever
A = Starter button
N = MODE button
O = ASR control button
Analogue instrument panel (01_02)
9
1 Vehicle
A = Ignition switch
1 Vehicle
01_02
A= High beam warning light
B = Turn indicator warning lights
10
D = ABS warning light
E = Speedometer
F = Immobiliser LED
G = Coolant temperature gauge
H = Engine control telltale light
I = Engine oil pressure warning light
L = Digital display
M = ASR warning light
Clock (01_03, 01_04, 01_05, 01_06)
Use the switch "MODE" to "ODO" mode
Hold the switch "MODE" for more than 3 seconds, the hours will be displayed. Hours
will increase each time the "MODE" button is pressed.
Once the hour is adjusted, hold the switch "MODE" more than 3 seconds to display
the minutes. Minutes will increase each time the "MODE" button is pressed.
If no key is pressed for 3 seconds, the system will leave the clock adjustment mode.
01_03
WARNING
FOR SAFETY REASONS THE TIME SETTING IS ONLY POSSIBLE WITH THE VEHICLE AT A STANDSTILL.
11
1 Vehicle
C = Fuel gauge
01_04
1 Vehicle
01_05
01_06
12
A = Clock
B = «SERVICE» icon
C = Kilometre-mile indicator
D = State of battery charge icon
E = Odometer indicator, partial odometer I and II, state of battery charge and cyclically
selectable ambient temperature with the «MODE» button
01_07
F = Ambient temperature indicator in degrees Celsius or Fahrenheit
G = Indicator «ODO», «ODO I» or «ODO II»
H = Low ambient temperature icon
*MODE* button (01_08)
Pushing the MODE button «A» for less than a second displays the following sequence
of functions:
•
•
•
•
•
01_08
Total Odometer «ODO»
Partial Odometer «ODO I»
Partial Odometer «ODO II»
State of battery charge
Ambient temperature «°»
To reset the trip odometer, move «ODO I» or «ODO II» and press for more than three
seconds the button MODE «A».
Key switch (01_09)
Ignition key «A» is located on the front leg shield back plate near the bag hook.
13
1 Vehicle
Digital lcd display (01_07)
SWITCH POSITIONS
ON«1»: Ready to start position, non-extractable key, mechanical antitheft device disabled.
OFF «2»: Ignition disabled, extractable key, mechanical antitheft device disabled.
LOCK «3»: Ignition disabled, extractable key, mechanical antitheft device enabled.
01_09
Locking the steering wheel (01_10)
Turn the handlebar to the left (as far as it will go), turn the key to «LOCK» and remove
the key.
01_10
Releasing the steering wheel (01_11)
1 Vehicle
Reinsert the key and turn it to «OFF».
01_11
14
Move switch «A» to the left to indicate a left turn; move switch «A» to the right to
indicate a right turn. Push the central part of switch «A» to deactivate the turn indicators.
01_12
Horn button (01_13)
Press the «A» button to sound the horn.
01_13
15
1 Vehicle
Switch direction indicators (01_12)
Light switch (01_14)
When the light switch «A» is in position «0» the low-beam light is ON; when it is in
position «1» the high-beam light is ON. If the light switch «A» is pressed when set to
«2», the high-beam light flashing is activated. The switch goes back to «0» automatically.
CAUTION
01_14
DO NOT PLACE, TRANSPORT OBJECTS AND/OR CLOTHES OVER THE FRONT
HEADLIGHT ASSEMBLY, WHEN THE HEADLIGHT IS TURNED ON OR OFF.
FAILURE TO FOLLOW THIS PRECAUTION MAY CAUSE OVERHEATING AND
THE SUBSEQUENT FUSION OF THE GLASS.
Start-up button (01_15)
Starter button «A». To start the vehicle, refer to the "starter motor" section.
1 Vehicle
01_15
16
The engine can be started when the emergency stop switch «A» is in position «1»
RUN; if the emergency stop switch «A» is in position «0» OFF the engine cannot be
started or it stops if it was running.
01_16
System ABS (01_17)
The vehicle is equipped with a locking ABS system on the wheels.
A: Tone wheel
B: Speed sensor
•
01_17
ABS: It is a hydraulic - electronic device that limits the pressure within the
braking circuit when a sensor, located on the wheel, detects its tendency to
lock. This system prevents the wheels from locking to avoid the risk of falling.
In case of failure of the ABS system, immediately reported to the rider with ABS warning light on the instrument panel, the vehicle retains the characteristics of a conventional braking system. In case of ABS warning light, reduce speed and go to an
Authorised Service Centre for the appropriate checks. The safety provided by the ABS
does not, in any case, justify risky manoeuvres. The stopping distance may be greater,
compared to a conventional vehicle equipped with traditional braking in the following
conditions:
•
•
Riding on rough roads, with gravel or snow
Riding on roads with holes or bumps
It is therefore recommended to reduce speed in these conditions.
17
1 Vehicle
Engine stop button (01_16)
WARNING
THE VEHICLE IS EQUIPPED WITH SERVO ASSISTED BRAKES.
AT VERY LOW SPEEDS (LESS THAN 5 KM/H) THE ABS SYSTEM IS DISABLED.
IT IS RECOMMENDED TO PAY ATTENTION THEREFORE IN CASES OF BRAKING IN LOW GRIP CONDITIONS AT LOW SPEED (FOR EXAMPLE BRAKING ON
GARAGE FLOOR TILES AFTER HAVING RIDDEN ON WET ROADS OR SIMILAR
SITUATIONS)
N.B.
THE ABS WARNING LIGHT TURNS ON AND STAYS ON UNTIL REACHING 5 KM/
H.
CAUTION
IN THE EVENT OF MALFUNCTION OF THE BATTERY, THE ABS - ASR SYSTEM
TURNS OFF
System ASR (01_18, 01_19)
1 Vehicle
ASR SYSTEM
The ASR system is a device to help riding that helps the rider during acceleration
manoeuvres, especially on slippery surfaces or in conditions that can cause sudden
slippage of the rear wheel. The ASR in these situations automatically intervenes by
reducing engine output within the limit imposed by the grip conditions, contributing
significantly to the maintenance of stability the vehicle.
18
THE ASR SYSTEM IS BASED ON THE RECOGNITION OF SPEED DIFFERENCES
BETWEEN FRONT AND REAR WHEEL. IN ORDER FOR THE SYSTEM TO MAINTAIN MAXIMUM EFFICIENCY IN ALL CONDITIONS, THE CALIBRATION PROCEDURE MUST BE PERFORMED EVERY TIME, EVEN IN CASE OF REPLACEMENT OF JUST ONE TYRE.
FOR THE CALIBRATION OF THE CONTROL UNIT PERFORM THE PROCEDURE
BELOW.
•
•
SWITCH «1»: on / off.
WARNING LIGHT «2»: operating indication warning light.
Flashing mode:
- Off with the vehicle in gear: the system is working, but is not active (normal condition).
- Flashing quickly with moving vehicle: the system is up and running (conditions of low
grip and intervention to reduce engine power); we recommend the utmost caution
because the grip limit has been exceeded; restore the vehicle safety conditions by
gently reducing the throttle opening.
01_18
- Lit with moving vehicle: the system is disabled and will not intervene in case of loss
of grip.
•
•
If the deactivation was voluntary (by pressing the appropriate button «1» for
1 second) it is recommended to replace the system as soon as possible.
If the deactivation was NOT voluntary, there is an ASR failure: in this case
you must contact an Authorised Service Centre for the diagnosis and the
reactivation of the system.
To ensure maximum safety of the vehicle it is advisable to keep the system active.
Deactivation may be necessary only in case of starting with very low grip surfaces
(mud, snow) on which the operation of the ASR could actually prevent the movement
of the vehicle.
19
1 Vehicle
WARNING
N.B.
AT VEHICLE START-UP THE ASR WARNING LIGHT FLASHES AT THE SAME
FREQUENCY AS THE ABS WARNING LIGHT, INDICATING A DIAGNOSTIC
PHASE OF THE SYSTEM. IN THE ABSENCE OF ERRORS, BOTH WARNING
LIGHTS TURN OFF AT THE SAME TIME WHEN EXCEEDING 5 KM/H.
IN CASE OF ABSENCE OF FLASHING AT START-UP, THE SYSTEM MAY NOT
WORKING, PLEASE CONTACT AN AUTHORISED SERVICE CENTRE.
WARNING
THE ASR SYSTEM IS ACTIVATED AT EVERY «ON» POSITIONING OF THE IGNITION SWITCH.
IF DISABLED BY THE USER, THE ASR SYSTEM KEEPS THE STATE OF INACTIVITY ONLY IF THE VEHICLE IS OFF, BY USING THE ENGINE STOP SWITCH;
AT THE NEXT KEY ON THE ASR SYSTEM IS ENABLED AUTOMATICALLY.
CAUTION
IT IS EMPHASISED THAT THE RIDING AUXILIARY SYSTEM CAN NOT CHANGE
THE PHYSICAL LIMITS OF GRIP AND IS NOT A SUBSTITUTE FOR PROPER
MANAGEMENT OF POWER, BOTH ON STRAIGHT STRETCHES AND IN TURNS.
THEREFORE, IT IS RECOMMENDED TO ALWAYS USE THE VEHICLE WITH THE
UTMOST CARE AND IN ACCORDANCE WITH THE REGULATIONS IN FORCE.
1 Vehicle
CAUTION
AT LOW SPEED (LESS THAN 5 KM/H), THE ASR SYSTEM DOES NOT WORK.
20
N.B.
IN CASE OF ROADS FULL OF HOLES THERE MAY OCCUR BRIEF ACTIVATION
OF THE ASR SYSTEM. THIS OCCURS UNDER NORMAL OPERATING CONDITIONS OF THE VEHICLE.
N.B.
THE DEVICE PREVENTS IMPRESSING ON THE REAR HIGH SPEED ROTATION
WHEEL WITH THE VEHICLE ON THE CENTRE STAND. IT IS RECOMMENDED
NOT TO INSIST WITH THE THROTTLE GRIP IN THIS PARTICULAR CONDITION.
CAUTION
A POOR STATE OF MAINTENANCE OF THE TYRES CAN RESULT IN ABNORMAL OPERATION OF THE ASR SYSTEM.
IN CASE OF REPEATED INTERVENTIONS OF THE ASR, EVEN ON ROAD SURFACES WITH GOOD GRIP OR SMALL THROTTLE OPENINGS, IT IS NECESSARY
TO CHECK FOR WEAR AND/OR THE STATE OF INFLATION OF TYRES FIRST.
IF THE PROBLEM PERSISTS, CONTACT AN AUTHORISED SERVICE CENTRE.
CAUTION
IN THE EVENT OF MALFUNCTION OF THE BATTERY, THE ABS - ASR SYSTEM
TURNS OFF
21
1 Vehicle
IT IS RECOMMENDED TO PAY PARTICULAR ATTENTION IN THE EVENT OF
ACCELERATION FROM STANDSTILL IN CONDITIONS OF LOW GRIP, ESPECIALLY IN THE FIRST METRES.
ASR SYSTEM CALIBRATION PROCEDURE.
In order to maintain the effectiveness of the ASR system following the replacement of
one or both tyres a calibration procedure of the system must be performed as follows
on a straight flat stretch of road.
• It is necessary that the diagnostic phase of the ASR systems and ABS is complete:
for this purpose, after the key ON, ride a short distance above 5 km/h and wait for the
flashing of the two warning lights to stop.
01_19
• Turn the ASR system off by pressing the button «1» on the handlebar and check that
the ASR disabling warning light «2» is on.
• Allow the engine to idle for at least 3 seconds.
• Press simultaneously the right brake lever, the engine start-up button and the ASR
on/off button «1» for at least 2 seconds. The activation process will be confirmed by
the ASR warning light «2» turning on with slow flashing.
• Accelerate to a constant speed of 30 to 40 km/h and maintain it for at least 7 to 8
seconds.
• The end of the procedure will be indicated by the flashing ASR warning light «2».
• Once the procedure is complete it is necessary to turn off the vehicle panel (key off)
and wait 30 seconds before turning the panel on (key on).
• In case of failure to complete the procedure within 2 minutes the ASR warning light
«2» will stay on steady and the ASR will remain off until the panel is turned off (key
off).
• To restart the vehicle panel (key on) it is necessary to reactivate the ASR. It is however necessary to repeat the process until it succeeds.
CAUTION
1 Vehicle
IF NECESSARY, CONTACT AN AUTHORISED SERVICE CENTRE.
22
In order to enhance theft protection, the vehicle is equipped with a «PIAGGIO IMMOBILIZER » electronic engine locking device that is activated automatically when the
ignition switch is removed. Upon start-up, the «PIAGGIO IMMOBILIZER» system
checks the starter key, and only if this key is recognised will the Immobiliser system
allow the vehicle to be started.
Keys (01_20, 01_21, 01_22)
Two types of keys are supplied together with the vehicle.
Key «A» is the «MASTER» key.
Only a single copy of this key is supplied, which is necessary to program all your other
keys and for your dealer to perform some maintenance operations. For this reason it
is advised that it be used only in exceptional circumstances.
The key «B» (single copy supplied) is used for regular operations such as:
01_20
- Engine starter
- Opening fuel tank cap
Together with the two keys, you will be given a CODE CARD bearing the same code
imprinted onto the two keys.
WARNING
LOSING THE MASTER KEY PREVENTS ANY FURTHER REPAIR OF THE "PIAGGIO IMMOBILISER" SYSTEM AND OF THE ENGINE CONTROL UNIT.
01_21
23
1 Vehicle
The immobilizer system
WARNING
KEEP THE "CODE CARD" AND THE MASTER KEY IN A SAFE PLACE (NOT IN
THE VEHICLE).
01_22
Immobilizer device enabled indicator led (01_23)
The activation of the «PIAGGIO IMMOBILISER» system is signalled by the a flashing
indicator «A».
In order to reduce battery discharge, the indicator LED turns off automatically after 48
hours of uninterrupted functioning.
Should the system fail, different LED flashing patterns will provide the Authorised
Service Centre with information on the type of fault detected.
01_23
1 Vehicle
Operation
Each time the ignition switch B» is removed while in the «OFF» or «LOCK» positions,
the protection system activates the engine lock. Turning the ignition key «B» to
«ON» disables the engine lock, provided that the safety system recognises the code
transmitted by the key. If the code is not recognised, turn the ignition switch B» first
to «OFF» and then back to «ON» again; if lock persists, try again using the «A» MASTER key. If the engine cannot be started, contact an Authorised Service Centre,
which is provided with the electronic equipment required to detect and repair the system.
24
Contact an Authorised Service Centre and bring the «A» MASTER key and all
«B» starter keys that you own.
The codes of starter keys not submitted for the new programming procedure are deleted from the memory. Any lost starter keys will therefore not be enabled to start the
engine.
WARNING
EACH KEY HAS ITS OWN AND UNIQUE CODE, WHICH MUST BE STORED IN
THE SYSTEM CONTROL UNIT MEMORY.
VIOLENT SHOCKS MAY AFFECT THE ELECTRONIC COMPONENTS OF THE
KEY.
IF THE VEHICLE IS SOLD, THE MASTER-HANDGRIP KEY (AS WELL AS THE
OTHER STARTER KEYS) AND THE «CODE CARD» MUST ALSO BE TRANSFERRED TO THE NEW OWNER.
Programming the immobilizer system (01_24)
Below is described the procedure to follow for programming the PIAGGIO IMMOBILISER system and/or for storing other key codes. The programming procedure should
be carried out with the engine stop switch set to «RUN».
START PROCEDURE
Insert the «MASTER» key «A» into the ignition switch (in «OFF») and turn it to
«ON». After 1 - 3 seconds, turn the key to «OFF » again and pull it out.
25
1 Vehicle
When the supplementary starter keys are required, remember that the all the keys,
whether new or existing, should be programmed.
INTERMEDIATE STAGE
After extracting the «MASTER» key «A», insert, within ten seconds, the key that is
going to be programmed «B» and turn it immediately to «ON». After 1-3 seconds, turn
the key to «OFF» again and pull it out. In this way, a maximum of 5 keys can be
programmed by repeating the above procedure and keeping the indicated times.
FINAL STAGE
After extracting the key to be programmed «B», insert the «MASTER» key «A» again
and turn it to «ON» (perform this operation within the 10 seconds following the extraction of the previous key). Leave it in this position for 1 to 3 seconds and return it
to «OFF».
CORRECT PROGRAMMING CHECK PHASE
Insert the «MASTER» key «A» disabling the transponder «C» (i.e., by tilting the key
cap by 90°), and turn the key to «ON». Perform the engine starter operation. Ensure
that the engine does not start. Insert the programmed key «B» and repeat the starter
operation. Check that engine starts.
WARNING
01_24
1 Vehicle
SHOULD YOU START THE ENGINE WITH THE MASTER KEY (WITH TRANSPONDER OFF) OR IN THE EVENT OF WRONG OPERATION DURING PROGRAMMING, REPEAT THE PROCEDURE FROM THE BEGINNING.
26
Raise the lock protection tab on the fuel tank cap. Insert the key and turn anticlockwise
to remove the cap.
01_25
Power supply socket (01_26)
There is a plug socket inside the front case.
The plug socket may be used for external consumers (mobile phone, inspection light,
etc.).
CAUTION
01_26
PROLONGED USE OF THE PLUG SOCKET MAY RESULT IN PARTIAL DISCHARGE OF THE BATTERY
Electric characteristic
Plug socket
12 V - 180 W MAX
27
1 Vehicle
Accessing the fuel tank (01_25)
Opening the saddle (01_27, 01_28)
With the key in position «OFF» or «ON» or with the engine ON, you can electrically
open the saddle by pressing button «A». If the electric opening does not work, use
the emergency lever B.
01_27
01_28
Identification (01_29, 01_30, 01_31)
1 Vehicle
Identification registration numbers are made up of a prefix and a number, stamped on
the chassis and on the engine. These numbers must always be quoted when ordering
spare parts. We recommend checking that the chassis registration number stamped
on the vehicle corresponds with that on the vehicle documentation.
28
BE REMINDED THAT ALTERING IDENTIFICATION REGISTRATION NUMBERS
CAN LEAD TO SERIOUS PENAL SANCTIONS (IMPOUNDING OF THE VEHICLE,
ETC.).
Chassis number
To read the chassis number, remove the port A in the front case.
01_29
01_30
29
1 Vehicle
CAUTION
Engine number
The engine number «B» is stamped near the rear left shock absorber lower support.
01_31
Rear top box opening (01_32)
Insert the key into the switch and press down until the glove compartment opens. In
the event that the switch is in «LOCK», turn the key to «OFF» or «ON» before pressing
it.
1 Vehicle
01_32
30
To use retractile bag hook mounted on the leg shield back plate, it is necessary to turn
it towards the rear part of the vehicle pressing where indicated by the arrow.
01_33
31
1 Vehicle
Bag clip (01_33)
32
1 Vehicle
LUM Beverly Sport Touring ABSASR
Chap. 02
Use
33
Checks
Before using the vehicle, check:
1. That the fuel tank is full.
2. The front and rear brake fluid level.
3. That the tyres are properly inflated.
4. Correct functioning of daylight running lights, headlight, and turn indicators.
5. The correct functioning of front and integral brakes.
6. The oil level in the gearcase.
7. The engine oil level.
8. Coolant level
Refuelling (02_01)
Raise the lock protection tab on the fuel tank cap. Insert the key and turn anticlockwise
to remove the cap.
WARNING
SWITCH OFF THE ENGINE BEFORE REFUELLING WITH PETROL.
02_01
PETROL IS HIGHLY INFLAMMABLE.
DO NOT SMOKE AND KEEP NAKED FLAMES AT A DISTANCE:FIRE HAZARD.
2 Use
DO NOT INHALE FUEL FUMES.
34
CAUTION
DO NOT USE THE VEHICLE TO THE COMPLETE EXHAUSTION OF THE FUEL;
SHOULD THIS OCCUR, DO NOT ATTEMPT TO START THE ENGINE. TURN THE
IGNITION SWITCH TO «OFF» AND TOP-UP THE TANK AS SOON AS POSSIBLE.
FAILURE TO FOLLOW THESE GUIDELINES COULD DAMAGE THE FUEL PUMP
AND/OR THE CATALYTIC CONVERTER.
CAUTION
CLEAN IMMEDIATELY THE PAINTED OR PLASTIC SURFACES THAT COME INTO CONTACT WITH THE FUEL TO AVOID LOSS OF THEIR SHINE OR ALTERATION OF THEIR MECHANICAL CHARACTERISTICS.
Characteristic
Fuel tank
13 l ± 1
35
2 Use
DO NOT ALLOW PETROL TO COME INTO CONTACT WITH HOT ENGINE OR
ANY PLASTIC PARTS.
Tyre pressure (02_02)
Check tyre pressure and wear periodically as indicated in the scheduled maintenance
table. Tyres feature wear indicators; replace tyres as soon as these indicators become
visible on the tyre tread. Also check that the tyres do not show signs of splitting at the
sides or irregular tread wear; if this occurs, go to an authorised workshop or at least
to a workshop equipped to replace tyres.
CAUTION
02_02
TYRE PRESSURE SHOULD BE CHECKED WHEN TYRES ARE COLD.INCORRECT TYRE PRESSURE CAUSES ABNORMAL TYRE WEAR AND MAKES RIDING DANGEROUS.
TYRES MUST BE REPLACED WHEN THE TREAD REACHES THE WEAR LIMITS
SET FORTH BY LAW.
TYRE INFLATION PRESSURE
Front tyre pressure (with
passenger)
2.2 bar (2.2 bar)
Rear tyre pressure (with
passenger)
2.4 bar (2.6 bar)
2 Use
TYRES
Front tyre
110/70 - 16'' M/C 52S Tubeless
Rear tyre
150/70 - 14" M/C 66S Tubeless
36
The preloading of the springs can be adjusted to 4 positions acting on the ring nut
located in the lower part of the shock absorbers with the specific spanner supplied.
Position 1: minimum preload: rider only
Position 2 medium preloading: rider only
Position 3 medium preloading: rider and passenger
Position 4: maximum preloading: rider, passenger, and luggage.
02_03
In order to carry out this operation you will need to use the specific spanner in the kit.
Spring preloading increases by turning the ring nut towards «A», but decreases if the
ring nut is turned towards «B».
CAUTION
RIDING THE VEHICLE WITH THE SPRING PRELOADING NOT CORRECTLY SET
FOR THE RIDER AND POSSIBLE PASSENGER, COULD REDUCE THE COMFORT OF THE RIDE AND THE PRECISION OF THE STEERING.
02_04
WARNING
WE RECOMMEND WEARING GLOVES WHILE CARRYING OUT THIS OPERATION IN ORDER TO AVOID INJURIES.
37
2 Use
Shock absorbers adjustment (02_03, 02_04)
WARNING
IT IS ABSOLUTELY FORBIDDEN TO ADJUST THE PRELOAD DIFFERENTLY ON
THE TWO SHOCK ABSORBERS
Running in (02_05)
DURING THE FIRST 1000 KM. DO NOT RIDE THE VEHICLE OVER 80% OF ITS
MAX. SPEED. AVOID OPENING THE THROTTLE GRIP COMPLETELY OR KEEPING A CONSTANT SPEED ALONG LONG SECTIONS OF ROAD. AFTER THE
FIRST 1000 KM. INCREASE SPEED PROGRESSIVELY, IF POSSIBLE, UNTIL THE
MAXIMUM PERFORMANCE IS OBTAINED.
CAUTION
02_05
2 Use
IN ORDER TO AVOID DAMAGING THE VEHICLE, PLEASE COMPLY WITH THE
RULES LISTED ABOVE.
38
The vehicle is equipped with an ignition prevention system controlled by the side
stand.
The engine cannot be started if the side stand is lowered.
If the engine is on, it will turn itself off if the side stand is lowered.
To start the engine it is necessary, before pressing the starter button, to pull and keep
pulled the front or rear brake lever, which activates the appropriate switch allowing
start-up.
02_06
- Rest the vehicle on its centre stand, making sure that the rear wheel is not touching
the ground.
- Keep the throttle grip at idle speed.
- Insert the key into the ignition switch «A» and turn it to «ON».
- Make sure that the emergency stop switch «B» is in position «RUN» and the side
stand is up and not engaged.
- Pull either the front, «C» or rear «D» brake lever and then press the starter button
«E».
WARNING
02_07
THE AUTOMATIC TRANSMISSION MAKES THE REAR WHEEL TURN EVEN
WHEN THE THROTTLE IS SLIGHTLY TWISTED. RELEASE THE BRAKE CAREFULLY AFTER STARTING, AND THEN ACCELERATE GRADUALLY.
CAUTION
02_08
DURING THE RUN-IN PERIOD, IT IS POSSIBLE THAT THE REAR WHEEL WITH
THE ENGINE IDLE AND THE VEHICLE ON THE STAND, MAY TURN SLIGHTLY;
THIS PHENOMENON SHOULD BE CONSIDERED NORMAL AND USUALLY DISAPPEARS AFTER A SHORT PERIOD OF USE.
39
2 Use
Starting up the engine (02_06, 02_07, 02_08)
CAUTION
DO NOT START-UP THE ENGINE IN CLOSED AREAS BECAUSE EXHAUST
GASES ARE TOXIC.
Precautions
CAUTION
NEVER STRESS THE ENGINE AT LOW TEMPERATURES IN ORDER TO AVOID
POSSIBLE DAMAGE. BE CAREFUL NEVER TO EXCEED THE MAXIMUM SPEED
WHILE RUNNING DOWNHILL, IN ORDER TO AVOID DAMAGING THE ENGINE.
IN ANY CASE, IN ORDER TO PRESERVE THE ENGINE FROM PROLONGED
OVERREVVING, THE REVOLUTION LIMITER WILL BE ACTIVATED IF THE ENGINE SPEED EXCEEDS THE ESTABLISHED THRESHOLD.
WARNING
2 Use
AFTER A LONG DISTANCE COVERED AT THE MAXIMUM SPEED, DO NOT STOP
THE ENGINE IMMEDIATELY, BUT LET IT RUN AT IDLE FOR A FEW SECONDS.
40
Fully untwist the throttle grip, then rotate the key in the switch «A » to «KEY
OFF» (extractable key).
02_09
Stand (02_10)
Centre stand bracket
Push with your foot on the centre stand's fork "A" while lifting the vehicle backward,
using the handlebar.
02_10
Side stand
Push with your foot on the fork of the stand «B» to bring it into open position, while
lifting the vehicle at the same time.
WARNING
THE SIDE STAND CAUSES THE ENGINE TO TURN ITSELF OFF WHENEVER IT
IS LOWERED.
41
2 Use
Stopping the engine (02_09)
TAMPERING MAY CAUSE SERIOUS VEHICLE MALFUNCTION.
CAUTION
DUE TO THE HIGH TEMPERATURES THE CATALYTIC CONVERTER CAN
REACH, ALWAYS TAKE CARE, WHEN PARKING THE VEHICLE, THAT THE EXHAUST DOES NOT COME INTO CONTACT WITH FLAMMABLE MATERIALS, TO
AVOID SERIOUS BURNS.
CAUTION
DO NOT SHUT OFF THE ENGINE WHILE THE VEHICLE IS MOVING. UNBURNED
FUEL COULD ENTER THE CATALYTIC CONVERTER AND BURN, CAUSING THE
CONVERTER TO OVERHEAT AND POSSIBLY DESTROYING IT.
Automatic transmission
To ensure simple, pleasurable riding, the vehicle is equipped with automatic transmission with regulator and centrifugal clutch. The system is designed to provide the
best performance (acceleration and consumption) while driving on both flat roads and
uphill.
If you have to stop on an uphill slope (traffic lights, traffic jam, etc.) use only the brake
to keep the vehicle still, leaving the engine running at idle speed. Using the
motor to keep the vehicle still can cause the clutch to overheat.
2 Use
It is therefore recommended to avoid conditions of prolonged clutch slippage (other
than those previously indicated) such as driving uphill fully laden on steep slopes, or
starting off with driver and passenger at slopes greater than 25%.
Take the following precautions if the clutch overheats:
42
2. Let the clutch cool down with the engine at idle speed for a few minutes.
Safe driving (02_11)
Some simple tips are provided below that will enable you to use your vehicle on a daily
basis in greater safety and peace of mind. Your skill and your mechanical knowledge
are the basis of a safe ride. We recommend trying out the vehicle in traffic - free zones,
in order to acquire a good knowledge of the vehicle it self.
1. Before riding off, remember to put the helmet on and fasten it correctly.
2. Reduce speed on rough roads and ride with care.
02_11
3. After riding on a long stretch of wet road without using the brakes, braking can be
poor at the beginning. In these conditions, it is a good idea to apply the brakes from
time to time.
4. Do not brake hard on wet, unsurfaced or slippery roads.
5. Avoid riding off by mounting the scooter when it is resting on its support. In any
case, in order to avoid abrupt departures, the rear wheel should not be turning when
in comes into contact with the ground.
6. If the vehicle is used on roads covered with sand, mud, snow mixed with salt, etc.,
clean the brake disc frequently with a mild detergent in order to prevent abrasive particles from building up inside the holes, which can result in early brake pad wear.
CAUTION
ALWAYS RIDE WITHIN YOUR LIMITS RIDING UNDER THE INFLUENCE OF ALCOHOL OR OTHER DRUGS AND CERTAIN MEDICINES IS EXTREMELY DANGEROUS.
43
2 Use
1.Do not continue riding in such conditions.
CAUTION
IN ORDER TO PREVENT ANY ACCIDENTS RIDE VERY CAREFULLY AFTER
ADDING ACCESSORIES AND WHILE CARRYING LUGGAGE. ADDING ACCESSORIES AND LUGGAGE CAN REDUCE THE VEHICLE'S STABILITY, PERFORMANCE AND SAFETY DURING USE.
NEVER RIDE THE VEHICLE EQUIPPED WITH ACCESSORIES (PANNIERS, TOP
BOX AND/OR WINDSHIELD) AT A SPEED HIGHER THAN 110 km/h.
THE VEHICLE CAN BE RIDDEN AT A HIGHER SPEED WITHOUT THE ACCESSORIES MENTIONED BEFORE WITHIN THE LIMITS ESTABLISHED BY LAW.
IF THERE ARE ANY NON-PIAGGIO ACCESSORIES INSTALLED, OR AN ABNORMAL LOAD, OR IF THE SCOOTER IS NOT IN A GENERALLY GOOD CONDITION, OR WHENEVER WEATHER CONDITIONS DEMAND IT, SPEED SHOULD
BE FURTHER REDUCED.
CAUTION
DO NOT ADJUST THE MIRRORS WHILE RIDING. THIS COULD CAUSE YOU TO
LOOSE CONTROL OF THE VEHICLE.
2 Use
CAUTION
ANY ELABORATION THAT MODIFIES THE VEHICLE'S PERFORMANCES, SUCH
AS TAMPERING WITH ORIGINAL STRUCTURAL PARTS IS STRICTLY FORBIDDEN BY LAW, AND RENDERS THE VEHICLE NO LONGER CONFORMING TO
THE APPROVED TYPE AND DANGEROUS FOR RIDING.
44
2 Use
45
46
2 Use
LUM Beverly Sport Touring ABSASR
Chap. 03
Maintenance
47
Engine oil level
In 4-stroke engines, engine oil is used to lubricate the distribution elements, the bushes and the thermal group. An insufficient quantity of oil can cause serious damage
to the engine.In all four-stroke engines, a loss of efficiency in oil performance and
certain consumption should be considered normal. Consumption can particularly reflect the conditions of use (i.e. when driving at 'full acceleration' all the time, oil
consumption increases). The replacement intervals provided for by the maintenance
programme are defined depending on the total content of oil in the engine and the
average consumption measured following standardised methods.
In order to prevent any problems, we recommend checking oil level more frequently than indicated in the Scheduled Maintenance table or before setting off
on long journeys. The scooter is, however, equipped with an oil pressure warning light on the instrument panel.
Engine oil level check (03_01, 03_02)
Every time the vehicle is used, visually inspect the level of the engine oil when the
engine is cold (after completely unscrewing the oil cap/dipstick). The oil level should
be somewhere between the MAX and MIN index marks on the level rod; «A»; while
the oil is being checked, the vehicle must be resting on its centre stand on an even,
horizontal surface.
If the check is carried out after the vehicle has been used, and therefore with a hot
engine, the level will be lower; in order to carry out a correct check, wait at least 10
minutes after the engine has been stopped so as to get the correct level.
3 Maintenance
03_01
48
3 Maintenance
03_02
Engine oil top-up (03_03)
The oil should be topped up after having checked the level and in any case by adding
oil without ever exceeding the MAX. level. The recovery level between the MIN and
MAX level entails a quantity of oil of approx. 600 cm³.
03_03
Warning light (insufficient oil pressure) (03_04)
The vehicle is equipped with a warning light that comes on when the key is turned to
«ON». However, this light should switch off once the engine has been started. If the
light comes on while braking, at idle speed or while turning a corner, it is necessary to check the oil level and top it up if required. If after having topped-up
the oil, the warning light still comes on while braking, at idle speed or while
turning a corner, it will be necessary to take your vehicle to an Authorised Service Centre.
03_04
49
Engine oil change (03_05, 03_06, 03_07, 03_08)
Have oil changed and cartridge filter «C» replaced as indicated in the scheduled
maintenance table at an Authorised Service Centre. Empty the engine by draining
the oil through drainage cap «C». In order to facilitate oil drainage, loosen the cap/
dipstick. Since a certain quantity of oil still remains in the circuit, add approx. 1100 to
1200 cm³ of oil through the cap «A». Then start the engine, leave it running for a few
minutes and shut it off: after 10 minutes check the level and, if necessary top it up
without exceeding the MAX level. The cartridge filter must be replaced every time
the oil is changed. For top-ups and changes, use new oil of the recommended type.
03_05
WARNING
CHECK THE STATE OF THE SEALING O-RING AND IF DAMAGED, REPLACE
WITH A NEW ONE.
THE ASSEMBLY, BE CAREFUL TO OIL IT SLIGHTLY.
WARNING
03_06
RUNNING THE ENGINE WITH INSUFFICIENT LUBRICATION OR WITH INADEQUATE LUBRICANTS ACCELERATES THE WEAR AND TEAR OF THE MOVING
PARTS AND CAN CAUSE IRRETRIEVABLE DAMAGE.
3 Maintenance
WARNING
EXCESSIVE OIL LEVEL AT TOP-UPS CAN LEAD TO SCALE FORMATION AND
VEHICLE MALFUNCTION.
03_07
50
USED OILS CONTAIN SUBSTANCES HARMFUL TO THE ENVIRONMENT. FOR
OIL CHANGE, CONTACT AN AUTHORISED SERVICE CENTRE WHICH IS EQUIPPED TO DISPOSE OF USED OILS IN AN ENVIRONMENTALLY FRIENDLY AND
LEGAL WAY.
CAUTION
03_08
USING OILS OTHER THAN THOSE RECOMMENDED CAN SHORTEN THE LIFE
OF THE ENGINE.
Recommended products
eni i-Ride scooter 15W-50
Synthetic-based lubricant for four stroke engines.
JASO MA, MA2 - API SJ - ACEA A3
Hub oil level (03_09)
Check the oil in the rear hub. To check the rear hub oil level, proceed as follows:
1. Rest the vehicle onto its centre stand, on level ground.
2. Unscrew the screw «A» and if oil comes out or touches the screw hole the level is
correct. Otherwise, top up the oil.
3. Screw the screw back in, checking that it is locked in place.
03_09
51
3 Maintenance
CAUTION
CAUTION
RIDING THE VEHICLE WITH INSUFFICIENT HUB LUBRICATION OR WITH CONTAMINATED OR IMPROPER LUBRICANTS ACCELERATES THE WEAR AND
TEAR OF THE MOVING PARTS AND CAN CAUSE SERIOUS DAMAGE.
CAUTION
USED OIL CAN HARM THE ENVIRONMENT. COLLECTION AND DISPOSAL
SHOULD BE CARRIED OUT IN COMPLIANCE WITH REGULATIONS IN FORCE.
CAUTION
UPON REPLACING HUB OIL, AVOID THE OIL COMING INTO CONTACT WITH
THE REAR WHEEL AND TYRE.
CAUTION
FOR OIL REPLACEMENT, CONTACT ANY AUTHORISED SERVICE CENTRE AS
THEY ARE EQUIPPED TO DISPOSE OF USED OILS IN AN ENVIRONMENTALLY
FRIENDLY AND LEGAL WAY.
3 Maintenance
Recommended products
AGIP GEAR SAE 80W-90
Lubricant for gearboxes and transmissions.
API GL-4
52
3 Maintenance
Characteristic
Transmission oil
About 500 cc
Tyres (03_10)
Check tyre pressure and wear periodically as indicated in the scheduled maintenance
table. Tyres feature wear indicators; replace tyres as soon as these indicators become
visible on the tyre tread. Also check that the tyres do not show signs of splitting at the
sides or irregular tread wear; if this occurs, go to an authorised workshop or at least
to a workshop equipped to replace tyres.
CAUTION
03_10
TYRE PRESSURE SHOULD BE CHECKED WHEN TYRES ARE COLD.INCORRECT TYRE PRESSURE CAUSES ABNORMAL TYRE WEAR AND MAKES RIDING DANGEROUS.
TYRES MUST BE REPLACED WHEN THE TREAD REACHES THE WEAR LIMITS
SET FORTH BY LAW.
WARNING
THE WHEELS FITTED WITH TYRES SHOULD ALWAYS BE BALANCED. RIDING
THE VEHICLE WITH VERY LOW TYRE PRESSURE OR WITH INCORRECTLY
BALANCED TYRES CAN LEAD TO DANGEROUS STEERING VIBRATIONS.
53
TYRES
Front tyre
110/70 - 16'' M/C 52S Tubeless
Rear tyre
150/70 - 14" M/C 66S Tubeless
TYRE INFLATION PRESSURE
Front tyre pressure (with
passenger)
2.2 bar (2.2 bar)
Rear tyre pressure (with
passenger)
2.4 bar (2.6 bar)
Spark plug dismantlement (03_11, 03_12)
Proceed as follows:
- Remove the case that grants access to the spark plug located on the right side fairing
by unscrewing the indicated screw.
- Disconnect spark plug HV wire cap «A».
- Unscrew the spark plug using the wrench supplied.
3 Maintenance
03_11
- When refitting, place the spark plug into the hole at the corresponding angle and
finger tighten it as far as it will go. Use the wrench only to tighten it.
- Place cap «A» fully over the spark plug.
54
SPARK PLUG MUST BE REMOVED WHEN THE ENGINE IS COLD. REPLACE
THE SPARK PLUG AS INDICATED IN THE SCHEDULED MAINTENANCE TABLE.
USE OF SPARK PLUGS OTHER THAN THE INDICATED TYPE CAN SERIOUSLY
DAMAGE THE ENGINE.
N.B.
03_12
USING SPARK PLUGS OTHER THAN THE INDICATED TYPE OR SHIELDLESS
SPARK PLUG CAPS CAN CAUSE ELECTRICAL SYSTEM FAILURES.
Characteristic
Spark plug
NGK CR7EKB
Removing the air filter (03_13)
To reach the air filter:
- Undo the seven screws«A» and remove the air filter cover.
03_13
55
3 Maintenance
WARNING
Air filter cleaning (03_14, 03_15, 03_16, 03_17)
1. Blow with compressed air from the white cotton side.
2. Wash with mild soap and water, without bending or twisting the filter, then dry with
compressed air.
3. Soak in a solution of 50% unleaded petrol and specified oil, using a brush.
CAUTION
03_14
IF THE VEHICLE IS USED ON DUSTY ROADS IT IS NECESSARY TO CARRY OUT
MAINTENANCE CHECKS OF THE AIR FILTER MORE OFTEN TO AVOID DAMAGING THE ENGINE.
Recommended products
AGIP FILTER OIL
Special product for the treatment of foam filters.
-
4. Check the lower part of the bleed cap for dirt.
3 Maintenance
REMOVE ANY DEPOSIT THAT MAY HAVE FORMED IN THE BLEED PIPE, COMING FROM THE FILTER BOX. PROCEED AS FOLLOWS:
1. remove the cap;
2. discharge the contents into a container and send it to a recycling bank.
03_15
56
03_16
6.Remove the clamp to allow the removal of the cap to check for the presence of oil
due to condensation of vapours.
REMOVE ANY DEPOSIT THAT MAY HAVE FORMED IN THE BLEED PIPE, COMING FROM THE FILTER BOX. PROCEED AS FOLLOWS:
1. remove the cap;
2. discharge the contents into a container and send it to a recycling bank.
03_17
Cooling fluid level (03_18, 03_19, 03_20, 03_21)
Engine cooling is carried out by a forced-circulation coolant system. The coolant consists of a mixture 50% de-ionised water and 50% glycol ethylene-based antifreeze
solution with corrosion inhibitors. The coolant supplied with the scooter is already
mixed and ready for use.
For the proper functioning of the engine, it is necessary for the coolant temperature
to be maintained at about 90 ° C. If the needle of the gauge enters the red zone, stop
the engine, let it cool down and check the coolant level; if the level is OK, contact an
Authorised Service Centre.
03_18
57
3 Maintenance
5.Working from the right side of the vehicle, unscrew the two indicated screws and
remove the plastic cover.
Check coolant when the engine is cold and as indicated in the scheduled maintenance
tables, following the steps below.
1. Set the vehicle upright on the stand and remove the cover by undoing screw «A».
2. Remove the expansion tank cap«B» by turning it anticlockwise.
3. Look inside the expansion tank and check that fluid level is always between the
«MIN» and «MAX» levels.
4. Top-up the fluid when it is close to the minimum mark.
03_19
If the level is not correct, proceed to top-up when the engine is cold. If the coolant
needs to be topped up frequently or the expansion tank is completely dry, check the
cooling system to find the cause of the problem. It is therefore essential to have the
cooling system checked at an Authorised Service Centre.
Replace coolant as indicated in the scheduled maintenance table. Take your vehicle
to an Authorised Service Centre for this operation.
WARNING
03_20
TO AVOID THE RISK OF SCALDING, DO NOT UNSCREW THE EXPANSION
TANK COVER WHILE THE ENGINE IS STILL HOT.
WARNING
3 Maintenance
IN ORDER TO AVOID HARMFUL FLUID LEAKS WHILE RIDING, IT IS IMPORTANT
TO MAKE SURE THAT THE LEVEL DOES NOT EXCEED THE REFERENCE
TONGUE TOO MUCH.
TO ENSURE CORRECT ENGINE OPERATION, KEEP THE RADIATOR GRILLE
CLEAN.
03_21
Recommended products
AGIP PERMANENT SPECIAL
58
Checking the brake oil level (03_22)
The front and rear brake fluid reservoirs are both positioned on the handlebar. Proceed
as follows:
- Rest the vehicle on its centre stand with the handlebars perfectly horizontal;
- Check the fluid level through the sight glass «A».
A drop in the brake fuel level may be caused by pad wear. Should the level appear to
be below the minimum mark, please contact an Authorised Service Centre or Dealer in order to have a thorough inspection of the braking system carried out.
03_22
Braking system fluid top up (03_23, 03_24, 03_25, 03_26, 03_27,
03_28, 03_29, 03_30, 03_31, 03_32, 03_33)
For topping-up, proceed as follows:
- Undo the three screws «A» and remove the windshield
- Loosen screw «B», slide the windshield support and rubber protection upwards
- Remove the mirrors unscrewing them from their seats
- Undo the two screws «C» and remove the pressure covering.
03_23
- Undo the two screws «D» and working from both sides of the vehicle, undo screw
«E».
- Using a flat-headed screwdriver, detach the fastener tab as shown in the figure,
accessing the tab via the indicated slit.
59
3 Maintenance
Ethylene glycol-based antifreeze fluid with organic inhibition additives. Red, ready to
use.
ASTM D 3306 - ASTM D 4656 - ASTM D 4985 - CUNA NC 956-16
- Insert the screwdriver between the two covers, as indicated in the figure, and detach
the upper fastener tab. Move the rear handlebar cover aside.
- Undo the two screws «F» and remove the front handlebar cover, by disengaging the
front headlamp unit connector
- Undo the two screws «G» and remove the cap«H» of the brake pump to restore the
optimal level
WARNING
03_24
BRAKING CIRCUIT FLUID IS HIGHLY CORROSIVE; MAKE SURE THAT IT DOES
NOT COME INTO CONTACT WITH THE PAINTWORK.
CAUTION
ONLY USE DOT 4-CLASSIFIED BRAKE FLUID.
WARNING
THE BRAKE FLUID IS HAZARDOUS: IN CASE OF ACCIDENTAL CONTACT,
WASH OFF WITH WATER.
WARNING
03_25
THE BRAKING CIRCUIT LIQUID IS HYGROSCOPIC, AND ABSORBS THE HUMIDITY OF SURROUNDING AIR. IF THE HUMIDITY IN THE BRAKING FLUID
EXCEEDS A CERTAIN VALUE, IT WILL LEAD TO INEFFICIENT BRAKING. NEVER USE BRAKING FLUID KEPT IN CONTAINERS THAT HAVE ALREADY BEEN
OPENED, OR PARTIALLY USED.
Recommended products
3 Maintenance
Brake fluid
Brake fluid.
Synthetic fluid SAE J 1703 -FMVSS 116 - DOT 3/4 - ISO 4925 - CUNA NC 956 DOT
4
03_26
60
3 Maintenance
03_27
03_28
03_29
61
03_30
3 Maintenance
03_31
03_32
62
3 Maintenance
03_33
Battery (03_34, 03_35, 03_36, 03_37)
To access the battery, proceed as follows:
- Position the vehicle on centre stand
- Open the saddle according to that described in the related section
- Exerting a light pressure on the indicated fitting, remove the cover of the toolkit compartment and the tools underneath
- Unscrew the three screws «A» and remove the cover «B»
03_34
The battery is the electrical device that requires the most frequent inspections and
diligent maintenance.
The main points of maintenance to be observed are as follows:
WARNING
DO NOT DISCONNECT THE BATTERY CABLES WITH THE ENGINE RUNNING,
THIS CAN CAUSE IRREPARABLE DAMAGE TO THE VEHICLE'S ELECTRONIC
CONTROL UNIT.
03_35
63
WARNING
USED BATTERIES ARE HARMFUL FOR THE ENVIRONMENT. COLLECTION
AND DISPOSAL SHOULD BE CARRIED OUT IN COMPLIANCE WITH REGULATIONS IN FORCE.
Characteristic
03_36
Battery
SEALED 12V/10Ah
03_37
Use of a new battery (03_38)
Ensure that the terminals are connected correctly and check the voltage.
3 Maintenance
CAUTION
DO NOT REVERSE THE POLARITY: RISK OF SHORT CIRCUIT AND DAMAGE
TO THE ELECTRICAL SYSTEM.
03_38
64
Battery performance will decrease if the vehicle is not used for a long time. This is the
result of the natural phenomenon of battery discharging, and may be due to residual
absorption by vehicle components with constant power consumption. Poor battery
performance may also be due to environmental conditions and the cleanness of the
poles. In order to avoid difficult starts and/or irreversible damage to the battery, follow
any of these steps:
- At least once a month start the engine and run it slightly above idle speed for 10-15
minutes. This keeps all the engine components, as well as the battery, in good working
order.
- Take your vehicle to a garage (as indicated in the «Vehicle not used for extended
periods» section) to have the battery removed. Have the battery cleaned, charged
fully and stored in a dry, ventilated place. Recharge at least once every two
months.
CAUTION
THE BATTERY MUST BE RECHARGED WITH A CURRENT LOAD EQUAL TO 1/10
OF THE BATTERY RATED CAPACITY AND FOR A PERIOD NOT LONGER THAN
8 HOURS. TAKE THE VEHICLE TO AN AUTHORISED PIAGGIO SERVICE CENTRE FOR THIS OPERATION. WHEN REFITTING THE BATTERY MAKE SURE THE
LEADS ARE CORRECTLY CONNECTED TO THE TERMINALS.
65
3 Maintenance
Long periods of inactivity
Fuses (03_39, 03_40)
The electrical system is equipped with 6 protection fuses located below the saddle.
Open the saddle and, as described above, remove the tools.
Unscrew the three screws «A» and remove the cover «B»
The chart shows the position and specifications of the fuses in the vehicle.
CAUTION
03_39
BEFORE REPLACING A BLOWN FUSE, FIND AND SOLVE THE FAILURE THAT
CAUSED IT TO BLOW. NEVER TRY TO REPLACE A FUSE WITH ANY OTHER
MATERIAL (A PIECE OF ELECTRIC WIRE, FOR INSTANCE).
CAUTION
03_40
MODIFICATIONS OR REPAIRS TO THE ELECTRICAL SYSTEM, PERFORMED
INCORRECTLY OR WITHOUT STRICT ATTENTION TO THE TECHNICAL SPECIFICATIONS OF THE SYSTEM CAN CAUSE MALFUNCTIONING AND RISK OF
FIRE.
FUSES
3 Maintenance
Fuse No. 1
Capacity: 20 A
Protected
circuits:
batterypowered: ABS control unit
Fuse No. 2
Capacity: 15 A
66
Fuse No. 3
3 Maintenance
Protected
circuits:
batterypowered: antitheft pre-installation,
saddle release control unit preinstallation, electric fan relay
(contact)
Capacity:10 A
Protected
circuits:electronic
control unit, injection load solenoid,
(contact)
Fuse No. 4
Capacity: 15 A
Protected
circuits:
batterypowered headlight relay (contact),
instrument panel, battery-powered
LV socket, helmet compartment
bulb, key powered saddle release
actuator
Fuse No. 5
Capacity: 10 A
Protected circuits: key powered:
antitheft pre-installation, saddle
release
control
unit
preinstallation, turn indicator control
device,
high-beam
flash,
instrument panel, daylight running
lights, horn, stop lights, start-up
enabling switch, license plate light
Fuse No. 6
Capacity: 5 A
Protected circuits: Protected
circuits: live power: headlight relay
(coil),
immobilizer
antenna,
electronic control unit, injection
67
load relay (coil), ABS control unit
and ASR warning light.
Fuse No. 7
Capacity: 30 A
Protected
circuits:
recharge battery
general,
Live: fuses No. 5 and 6
Lamps
BULBS
Low beam light bulb
Type: Halogen H7
Quantity: 1
Power: 12V - 55W
High beam light bulb
Type: Halogen H7
Quantity: 1
3 Maintenance
Power: 12V - 55W
Front tail light bulb
Type: LED
Quantity: Power: -
Front turn indicator light bulb
Type: Spherical BAU 15s
68
3 Maintenance
Quantity: 1 Right - 1 Left
Power: 12V - 10W
Stop light/rear daylight running
light bulb
Type: LED
Quantity: Power: -
Rear turn indicator light bulb
Type: Spherical BAU 15s
Quantity: 1 Right - 1 Left
Power: 12V - 10W
License plate light bulb
Type: All glass W5W
Quantity: 1
Power: 12V - 5W
Helmet compartment light bulb
Type: Cylindrical C5W
Quantity: 1
Power: 12V - 5W
Instrument panel lighting bulb
Type: LED
Quantity: 4
Power: -
69
Front light group (03_41, 03_42, 03_43, 03_44)
To remove the front headlight assembly the windshield does not need to be removed.
To remove the front headlight assembly, proceed as follows:
- Unscrew the two screws «A» and remove the pressure covering
- Unscrew the two upper screws «E» fastening the headlight assembly
- Working on both sides of the vehicle, unscrew the lower fixing screws «C» and remove the headlight. Remove the rubber protection.
03_41
This gives access to the bulbs.
To replace the low-beam light act on the lamp holder«D». To replace the high-beam
light act on the lamp holder«E» unhooking the relevant pin.
To reassemble, repeat the operation but in reverse order.
WARNING
HIGH- AND LOW-BEAM BULBS ARE HALOGEN TYPE: DO NOT TOUCH THEM
WITH YOUR FINGERS TO AVOID DAMAGING THEIR FUNCTION.
03_42
CAUTION
3 Maintenance
DO NOT PLACE, TRANSPORT OBJECTS AND/OR CLOTHES OVER THE FRONT
HEADLIGHT ASSEMBLY, WHEN THE HEADLIGHT IS TURNED ON OR OFF.
FAILURE TO FOLLOW THIS PRECAUTION MAY CAUSE OVERHEATING AND
THE SUBSEQUENT FUSION OF THE GLASS.
03_43
70
3 Maintenance
03_44
Headlight adjustment (03_45, 03_46, 03_47)
Proceed as follows:
- Position the vehicle in running order and with the tyres inflated to the prescribed
pressure, onto a flat surface, 10 m away from a half-lit white screen; ensure that the
longitudinal axis of the vehicle is perpendicular to the screen;
- Turn on the headlight and check that the borderline of the projected light beam on
the screen is not higher than 9/10 or lower than 7/10 of the distance from the ground
to the centre of the vehicle headlamp;
03_45
- Otherwise, adjust the headlight. For this operation it is not necessary to remove the
windshield. Unscrew the two screws «A» and remove the pressure covering. Screw
in the screw «B» to lower the light beam, unscrew the screw «B» to raise the light
beam.
N.B.
THE ABOVE PROCEDURE COMPLIES WITH THE EUROPEAN STANDARDS REGARDING MAXIMUM AND MINIMUM HEIGHT OF LIGHT BEAMS. REFER TO THE
STATUTORY REGULATIONS IN FORCE IN EVERY COUNTRY WHERE THE VEHICLE IS USED.
03_46
71
03_47
Front direction indicators (03_48, 03_49, 03_50)
To replace the indicator bulbs proceed as follows:
- Open the front case
- Remove the rubber protection
- Remove the lamp holder, rotating it towards the inside of the vehicle
- Lightly press the lamp and turn it anticlockwise and remove it.
03_48
3 Maintenance
WARNING
THE DAYLIGHT RUNNING LIGHTS PRESENT IN THE SAME GROUP ARE «LED»
TYPES. IN CASE OF MALFUNCTIONING, AS THE REMOVAL IS PARTICULARLY
DIFFICULT, WE ADVISE ADDRESSING AN Authorised PIAGGIO Service Centre
FOR THE REPLACEMENT.
03_49
72
3 Maintenance
03_50
Rear optical unit (03_51, 03_52, 03_53)
To replace the indicator bulbs proceed as follows:
- Open the saddle
- Remove the rubber protection
- Remove the lamp holder turning it towards the base
- Lightly press the lamp and turn it anticlockwise and remove it.
03_51
WARNING
THE DAYLIGHT RUNNING LIGHTS PRESENT IN THE SAME GROUP ARE «LED»
TYPES. IN CASE OF MALFUNCTIONING, AS THE REMOVAL IS PARTICULARLY
DIFFICULT, WE ADVISE ADDRESSING AN Authorised PIAGGIO Service Centre
FOR THE REPLACEMENT.
03_52
73
03_53
Number plate light (03_54)
Unscrew the indicated screw and then take out the lamp holder.
CAUTION
DO NOT PULL THE ELECTRICAL WIRING TO EXTRACT THE BULB HOLDER.
3 Maintenance
03_54
74
Open the helmet compartment, take out the snap-on transparent glass and replace
the bulb.
03_55
Rear-view mirrors (03_56)
Adjust the mirrors by applying slight pressure to the side of the mirror to move it to the
desired position.
03_56
75
3 Maintenance
Helmet compartment lighting bulb (03_55)
Front and rear disc brake (03_57)
The brake disc and pad wear is automatically compensated, therefore it has no effect
on the functioning of the front and rear brakes. For this reason it is not necessary to
adjust the brakes. An excessively elastic brake lever stroke may indicate the presence
of air in the braking circuit or a failure in the braking system. In this case, mainly due
to the importance of brakes to guarantee safe riding conditions, the vehicle should be
taken to an Authorised Service Centre or Dealer.
CAUTION
03_57
BRAKING SHOULD BEGIN AFTER ABOUT 1/3 OF THE BRAKE LEVER STROKE.
IN CASE OF EXCESSIVE TRAVEL, CHECK THE PROPER OPERATION OF THE
BRAKE SYSTEM AT AN AUTHORISED SERVICE CENTRE.
CAUTION
3 Maintenance
HAVE THE BRAKE PADS CHECKED BY THE DEALER ACCORDING TO THE
CHECKS SPECIFIED IN THE SCHEDULED MAINTENANCE TABLE. HOWEVER,
IN THE EVENT OF NOISES COMING FROM THE FRONT AND/OR REAR BRAKING SYSTEM DURING OPERATION, IT IS ADVISABLE TO HAVE THE BRAKING
SYSTEM CHECKED BY AN AUTHORISED SERVICE CENTRE OR DEALER. AFTER REPLACING THE BRAKE PADS, DO NOT USE THE SCOOTER UNTIL YOU
HAVE OPERATED THE BRAKE LEVER SEVERAL TIMES IN ORDER TO ALLOW
THE PLUNGERS TO SETTLE AND THE LEVER STROKE TO BE SET TO THE
CORRECT POSITION.
CAUTION
THE PRESENCE OF SAND, MUD, SNOW MIXED WITH SALT, ETC. ON THE
ROAD, CAN DRASTICALLY REDUCE THE LIFE OF THE BRAKE PADS. WHEN
RIDING THE VEHICLE ON ROADS WITH THE ABOVE MENTIONED CHARAC76
Puncture
The vehicle is equipped with Tubeless tyres (without inner tube). In the event of a
puncture, Tubeless tyres - unlike tyres with inner tubes - go flat very slowly, resulting
in a greater steering safety. In the event of a puncture, an emergency repair can be
carried out using an "inflate and repair" spray can. For a final repair, take your vehicle
to an Authorised Service Centre or Dealer. The replacement of a tyre involves removing the wheel in question. Take your vehicle to an Authorised Service Centre
or Dealer for these operations.
CAUTION
TO USE THE "INFLATE AND REPAIR" SPRAY CAN PROPERLY, FOLLOW THE
INSTRUCTIONS ON THE PACKAGING.
WARNING
THE WHEELS FITTED WITH TYRES SHOULD ALWAYS BE BALANCED. RIDING
THE VEHICLE WITH VERY LOW TYRE PRESSURE OR WITH INCORRECTLY
BALANCED TYRES CAN LEAD TO DANGEROUS STEERING VIBRATIONS.
77
3 Maintenance
TERISTICS, WE RECOMMEND TO CLEAN THE BRAKE DISC FREQUENTLY
WITH A NON-AGGRESSIVE DETERGENT IN ORDER TO AVOID THE FORMATION OF ABRASIVE BUILD-UPS IN THE HOLES, WHICH COULD RESULT IN
EARLY WEAR OF BRAKE PADS.
Periods of inactivity (03_58)
The following operations are recommended:
1. Clean the scooter thoroughly and then cover it with a canvas;
2. With the engine off and the piston at the bottom dead centre position, remove the
spark plug, and pour 1 ÷ 2 cm³ of the recommended oil through its hole. Operate the
starter button 1-2 times for roughly 1 second to turn the engine over slowly, then insert
the spark plug again;
03_58
3. Ensure that the fuel tank is at least half full (so that the fuel pump is fully
covered); spread antirust grease on the uncoated metal parts; keep the wheels lifted
above the ground by resting the chassis on two wooden wedges;
4. As regards the battery, follow the instructions in the «Battery» section.
Recommended products
eni i-Ride PG 5W-40
Synthetic based lubricant for high-performance four-stroke engines.
JASO MA, MA2 - API SL - ACEA A3
Cleaning the vehicle
3 Maintenance
Use a low pressure jet of water to soften the caked dirt and mud deposited on the
painted surfaces. Once softened, sponge off mud and dirt using a car body sponge
soaked in a car body shampoo and water solution (2-4% of car shampoo in water).
Then rinse with abundant water, and dry with a shammy cloth. For the engine exterior,
use petrol, a brush and clean cloths. Petrol can damage paintwork. Remember that
any polishing with silicone wax must always be preceded by washing.
78
DETERGENTS CAN POLLUTE WATER. THE VEHICLE MUST BE WASHED AT A
WASH STATION EQUIPPED WITH A SPECIAL WATER PURIFICATION SYSTEM.
CAUTION
DO NOT USE A HIGH-PRESSURE WATER JET MACHINE TO CLEAN THE ENGINE AND/OR VEHICLE; HOWEVER, IF NO OTHER MEANS ARE AVAILABLE, IT
IS THEN NECESSARY TO:
• ONLY USE A FANLIKE SPRAY JET.
• DO NOT PLACE THE NOZZLE CLOSER THAN 60 CM.
• DO NOT USE WATER AT TEMPERATURES OVER 40ºC.
• DO NOT USE HIGH-PRESSURE WATER JETS.
• DO NOT STEAM WASH.
• DO NOT AIM THE JET AT: THE ENGINE, THE WIRING, THE COOLING SLITS
ON THE TRANSMISSION OR SCROLL COVERS.
CAUTION
NEVER WASH THE SCOOTER IN DIRECT SUNLIGHT, ESPECIALLY IN SUMMER
WHEN THE BODYWORK IS STILL HOT AS THE SHAMPOO COULD DAMAGE
THE PAINTWORK IF IT DRIES BEFORE BEING RINSED OFF. NEVER USE
CLOTHS SOAKED IN ALCOHOL, PETROL, DIESEL OIL OR KEROSENE FOR
CLEANING THE PAINTED OR PLASTIC SURFACES, IN ORDER NOT TO DAMAGE THE LUSTRE FINISH OR ALTER THEIR MECHANICAL PROPERTIES. USING SILICONE-BASED WAX CAN DAMAGE THE PAINTED SURFACES, DEPENDING ON THE VEHICLE COLOUR (SATIN COLOURS). FOR FURTHER
79
3 Maintenance
CAUTION
INFORMATION ON THIS MATTER, CONTACT AN AUTHORISED SERVICE CENTRE.
WARNING
CLEAN YOUR SCOOTER FREQUENTLY SO AS TO AVOID POSSIBLE DIRT OR
MUD DEPOSITS THAT COULD CAUSE MALFUNCTIONING IN THE THROTTLE
GRIP TRANSMISSION AND/OR OTHER COMPONENTS.
Troubleshooting
3 Maintenance
STARTING FAILURE
Emergency switch in «OFF»
Set the switch back to «ON»
Fuse blown
Replace the blown fuse and have
the vehicle checked by an
Authorised Service Centre.
DIFFICULTY STARTING
Lack of fuel in tank.
Refuelling
Injection system fault
Contact an Authorised Service
Centre
80
Contact an Authorised Service
Centre
Flat battery
Recharge the battery.
3 Maintenance
Fuel pump fault
* IMPORTANT: DO NOT USE THE SCOOTER TO THE COMPLETE
EXHAUSTION OF FUEL; SHOULD THIS OCCUR, DO NOT
ATTEMPT TO START THE ENGINE. TURN THE IGNITION KEY TO
«OFF» AND TOP-UP THE FUEL TANK AS SOON AS POSSIBLE.
FAILURE TO FOLLOW THESE GUIDELINES COULD DAMAGE THE
FUEL PUMP AND/OR THE CATALYTIC CONVERTER.
IGNITION PROBLEMS
Faulty spark plug
Contact an Authorised Service
Centre.
Faulty ignition / injection control
Contact an Authorised Service
unit. Due to the presence of high Centre
voltage, this check should only be
carried out by an expert.
LACK OF COMPRESSION
Loose spark plug.
Screw in the spark plug tightly
Cylinder head loose, piston gas
rings worn.
Contact an Authorised Service
Centre.
Valve stuck
Contact an Authorised Service
Centre.
81
HIGH CONSUMPTION AND LOW PERFORMANCE
Air filter blocked or dirty.
Clean or replace.
INSUFFICIENT BRAKING
Greasy disc. Worn pads. Faulty
Contact an Authorised Service
braking system. Presence of air in Centre.
the front and rear brake circuit.
INEFFICIENT SUSPENSION
Shock absorber fault, oil leak, end Contact an Authorised Service
buffers damaged; shock absorber Centre.
preloading incorrectly set
3 Maintenance
AUTOMATIC TRANSMISSION PROBLEMS
CVT rollers and/or drive belt
damaged
Contact an Authorised Service
Centre.
82
LUM Beverly Sport Touring ABSASR
Chap. 04
Technical data
83
4 Technical data
04_01
84
4 Technical data
ENGINE TECHNICAL DATA
Type
Single-cylinder, 4-stroke
Engine capacity
330 cm³
Bore x stroke
78 x 69 mm
Compression ratio
12.0±0.5
Engine idle speed
1700±100 rpm
Timing system
Four valves, single overhead
camshaft, chain-driven.
Valve clearance
Intake: 0.10 mm
Exhaust: 0.15 mm
Max. power to the shaft
24.5 kW at 8250 rpm
MAX. torque
32.3 Nm at 6250 rpm
Transmission
With
continuously
variable
transmission, torque server, V belt,
centrifugal automatic clutch in oil
bath.
Final reduction gear
Gear reduction unit in oil bath.
Lubrication
Engine lubrication with trochoidal
pump (inside the crankcase), oil
filter and pressure adjustment bypass.
Cooling
Forced coolant circulation system.
85
Electric
Electric starter
Ignition
Electronic, inductive, high
efficiency ignition, integrated with
the injection system, with variable
advance and separate H.V. coil.
Ignition advance
Three-dimensional map managed
by control unit
Fuel system
IAWM3G electronic injection with
38 mm diameter throttle body,
electric fuel pump.
Spark plug
NGK CR7EKB
Fuel
Unleaded petrol (95 RON)
Silencer
Absorption-type exhaust silencer
with
a
three-way
catalytic
converter and lambda probe to the
exhaust.
Emissions compliance
EURO 3
4 Technical data
VEHICLE TECHNICAL DATA
Chassis
Tubular and steel sheets.
Front suspension
Hydraulic telescopic fork with Ø 35mm stem
Rear suspension
Two double-acting shock
absorbers, adjustable to four
positions at preloading.
86
Ø 300-mm disc brake with
hydraulic control activated by
handlebar right-side lever; braking
assisted by ABS system.
Rear brake
Ø 240-mm rear disc brake with
hydraulic control operated by the
handlebar left-side lever; braking
assisted by ABS system.
Wheel rim type
Light alloy wheel rims.
Front wheel rim
Die-cast aluminium alloy, 2.15 x16"
Rear wheel rim
Die-cast aluminium alloy 2.75 x14"
Front tyre
110/70 - 16" M/C 52S Tubeless
Rear tyre
150/70 - 14" M/C 66S Tubeless
Front tyre pressure (with
passenger)
2.2 bar (2.2 bar)
Rear tyre pressure (with
passenger)
2.4 bar (2.6 bar)
Kerb weight
179 kg ± 8 kg
Maximum weight allowed
375 kg
Battery
SEALED 12V/10Ah
4 Technical data
Front brake
CAPACITY
Engine oil
about 1.5 l
87
Transmission oil
about 500 cc
Cooling system fluid
1.75 l
Fuel tank
13 l ± 1
Toolkit (04_02, 04_03)
The tools are stored under the saddle.
The toolkit includes:
4 Technical data
04_02
•
•
•
•
•
•
One box-spanner
One twin screwdriver
One special key for adjusting rear shock absorbers
An extractor for fuses
One lever for box-spanner
One double torx wrench
04_03
88
LUM Beverly Sport Touring ABSASR
Chap. 05
Spare parts and
accessories
89
Warnings (05_01)
WARNING
TO PREVENT ACCIDENTS AND TO GUARANTEE PROPER STABILITY, PERFORMANCE AND SAFETY, RIDE THE VEHICLE VERY CAREFULLY WHEN IT IS
FITTED WITH ACCESSORIES OR WITH UNUSUAL LOADS.
05_01
WARNING
IT IS ALSO RECOMMENDED THAT ORIGINAL PIAGGIO SPARE PARTS BE
USED, AS THESE ARE THE ONLY ONES OFFERING YOU THE SAME QUALITY
GUARANTEE AS THOSE INITIALLY FITTED ON THE SCOOTER. THE USE OF
NON-ORIGINAL SPARE PARTS RENDERS THE WARRANTY VOID.
5 Spare parts and accessories
WARNING
PIAGGIO MARKETS ITS OWN LINE OF ACCESSORIES THAT ARE RECOGNISED AND GUARANTEED FOR USE. IT IS THEREFORE ESSENTIAL TO CONTACT AN AUTHORISED DEALER OR SERVICE CENTRE IN ORDER TO CHOOSE
AND FIT ACCESSORIES CORRECTLY. THE USE OF NON-ORIGINAL ACCESSORIES MAY AFFECT THE STABILITY AND OPERATION OF YOUR VEHICLE
AND REDUCE SAFETY LEVELS WITH POTENTIAL RISKS FOR THE RIDER.
NEVER RIDE THE VEHICLE EQUIPPED WITH ACCESSORIES (PANNIERS, TOP
BOX AND/OR WINDSHIELD) AT A SPEED HIGHER THAN 110 km/h.
90
IF THERE ARE ANY NON-PIAGGIO ACCESSORIES INSTALLED, OR AN ABNORMAL LOAD, OR IF THE SCOOTER IS NOT IN A GENERALLY GOOD CONDITION, OR WHENEVER WEATHER CONDITIONS DEMAND IT, SPEED SHOULD
BE FURTHER REDUCED.
WARNING
BE EXTREMELY CAREFUL WHEN INSTALLING AND REMOVING THE MECHANICAL ANTITHEFT DEVICE ON THE VEHICLE (U-SHAPED PADLOCK, DISC
BLOCK, ETC.).
MAINLY NEAR THE BRAKE PIPES, TRANSMISSIONS AND/OR ELECTRIC CABLES, AN INCORRECT INSTALLATION OR REMOVAL OF THE ANTITHEFT
DEVICE AS WELL AS LEAVING IT ON BEFORE STARTING THE VEHICLE CAN
SERIOUSLY DAMAGE ITS COMPONENTS, COMPROMISE THE CORRECT
FUNCTIONING OF THE VEHICLE AND USERS' SAFETY.
91
5 Spare parts and accessories
THE VEHICLE CAN BE RIDDEN AT A HIGHER SPEED WITHOUT THE ACCESSORIES MENTIONED BEFORE WITHIN THE LIMITS ESTABLISHED BY LAW.
92
5 Spare parts and accessories
LUM Beverly Sport Touring ABSASR
Chap. 06
Scheduled
maintenance
93
Scheduled servicing table (06_01)
Adequate maintenance is fundamental to ensuring long-lasting, optimum operation
and performance of your vehicle.
To this end, a series of checks and maintenance operations (at the owner's expense)
have been suggested, which are included in the summary table on the following page.
Any minor faults should be reported without delay to an Authorised Service Centre
or Dealer without waiting until the next scheduled service to solve it.
06_01
It is indispensable to have your vehicle serviced to the prescribed intervals of time,
even if you have not reached the predicted mileage. Punctual vehicle servicing is
necessary for the correct use of the guarantee. For all further information regarding
the Guarantee application modes and the execution of the "Programmed Maintenance" refer to the "Guarantee Booklet".
SCHEDULED MAINTENANCE TABLE
km x 1.000
1
10
Safety fasteners
I
Spark plug
6 Scheduled maintenance
Centre stand bracket
L
15
20
30
40
I
I
I
R
R
L
L
Drive belt
Throttle control
I
I
I
Roller housing / Roller counter
Belt compartment filter(*)
60
I
I
I
R
R
R
R
L
L
L
L
R
I
C/I
Engine air filter (*)
Engine oil filter
50
R
R
45
I
R
I
C/I
I
C/I
C
C
C
C
C
C
R
R
R
R
R
R
C
C
C
C
C
C
Valve clearance
I
94
1
10
Electrical system and battery
I
Coolant (****)
15
20
30
40
I
I
I
I
I
I
Brake fluid (****)
I
I
Engine oil (**)
R
R
Hub oil
R
Brake pads
I
45
50
60
I
I
I
I
I
I
I
I
I
I
I
I
R
R
R
R
R
I
I
I
I
I
CVT sliders and rollers
I
R
Brake pumps
R
I
R
R
R
R
R
Tyre pressure and wear
I
I
I
I
I
I
I
Vehicle road test
I
I
I
I
I
I
I
Crankcase breather (***)
C
C
C
Suspension
I
I
I
I
I
I
I
Steering
A
I
I
I
I
I
I
I: CHECK AND CLEAN, ADJUST, LUBRICATE OR REPLACE IF NECESSARY.
C: CLEAN, R: REPLACE, L: LUBRICATE, A: ADJUST
* Perform maintenance more frequently when riding in unusually wet or dusty areas
** Check, however, the level every time you use your vehicle
*** Perform maintenance more frequently if you drive mainly at full acceleration
*** Replace every 2 years
95
6 Scheduled maintenance
km x 1.000
RECOMMENDED PRODUCTS TABLE
Product
Description
AGIP GEAR SAE 80W-90
Lubricant for gearboxes and transmissions.
API GL-4
AGIP FILTER OIL
Special product for the treatment of foam
filters.
-
AGIP GP 330
Water repellent stringy calcium spray grease.
R.I.D./A.D.R. 2 10°b) 2 R.I.Na. 2.42 - I.A.T.A.
2 - I.M.D.G. class 2 UN 1950 Pag. 9022 EM
25-89
eni i-Ride scooter 15W-50
Synthetic-based lubricant for four stroke
engines.
JASO MA, MA2 - API SJ - ACEA A3
AGIP BRAKE 4
Brake fluid.
Synthetic fluid SAE J 1703 -FMVSS 116 - DOT
3/4 - ISO 4925 - CUNA NC 956 DOT 4
AGIP PERMANENT SPECIAL
Ethylene glycol-based antifreeze fluid with
ASTM D 3306 - ASTM D 4656 - ASTM D 4985
organic inhibition additives. Red, ready to use. - CUNA NC 956-16
UNIT OF MEASURE - CONVERSION - ENGLISH SYSTEM
TO INTERNATIONAL SYSTEM (IS).
6 Scheduled maintenance
Specifications
1 Inch (in)
25.4 Millimetres (mm)
1 Foot (ft)
0.305 Meter (m)
1 Mile (mi)
1.609 Kilometre (km)
1 US Gallon (USgal)
3.785 Litre (l)
1 Pound (lb)
0.454 Kilogram (kg)
1 Cubic inch (in³)
16.4 Cubic centimetres (cm³)
1 Foot pound (ft lb)
1,356 Newton meter (Nm)
96
1.602 Kilometres per hour (km/h)
1 Pound per square inch (PSI)
0.069 (bar)
1 Fahrenheit (°F)
32+(9/5) Celsius (°C)
6 Scheduled maintenance
1 Miles per hour (mi/h)
97
98
6 Scheduled maintenance
TABLE OF CONTENTS
A
F
L
ABS: 17
Air filter: 55, 56
Fuel: 27
Fuses: 66
Light switch: 16
Start-up: 16
Switch: 13, 15, 16
M
T
Maintenance: 47, 93
Tank: 27
Technical Data: 83
Toolkit: 88
Top box: 30
Transmission: 42
Tyre pressure: 36
Tyres: 53
B
H
Battery: 63, 64
Brake: 59, 76
Headlight: 71
Horn: 15
Hub oil: 51
C
Checks: 34
Clock: 11
Mirrors: 75
P
Puncture: 77
I
Identification: 28
Immobilizer: 23–25
Instrument panel: 9
R
Refuelling: 34
D
Disc brake: 76
Display: 13
V
Vehicle: 7, 78
K
S
Key switch: 13
Keys: 23
Saddle: 28
Scheduled maintenance: 93
Shock absorbers: 37
Spark plug: 54
Stand: 41
E
Engine oil: 48–50
Engine stop: 17
99
The descriptions and images in this publication are given for illustrative purposes only and are not binding. While the basic characteristics as described and illustrated in this booklet remain unchanged,
Piaggio & C. S.p.A. reserves the right, at any time and without being required to update this publication beforehand, to make any changes to components, parts or accessories, which it considers
necessary to improve the product or which are required for manufacturing or construction reasons.
Not all versions/models shown in this publication are available in all countries. The availability of each model should be checked at the official PIAGGIO sales network.
© Copyright 2012 - Piaggio & C. S.p.A. All rights reserved. Reproduction of this publication in whole or in part is prohibited.
Piaggio & C. S.p.A. Viale Rinaldo Piaggio, 25 - 56025 PONTEDERA (PI), Italy
www.piaggio.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement