IMPORTANT ADVICE FOR INITIAL SETUP

IMPORTANT ADVICE FOR INITIAL SETUP
FOR YOUR PEACE OF MIND
OWNER’S MANUAL
DIGITAL TOUCHSCREEN MOVEMENT
& SOUND BABY MONITOR
Model AC701
IMPORTANT ADVICE FOR INITIAL SETUP
DON
’T
FORG
ET
Movement Alarm
Your monitor comes with the movement alarm activated.
When switching on your monitor it will alarm, with or without
the Sensor Pad plugged in, if no movement is detected.
Deactivate the movement function to use the monitor without
the Sensor Pad.
Batteries
Insert the enclosed rechargeable batteries into the Parent
Unit. If inserted incorrectly the Parent Unit will not charge
when placed in the charging cradle. The battery icon will flash
briefly on the Parent Unit screen to indicate charging.
Cord Safety
Ensure the Nursery Unit is at least 1 metre away from your
baby’s cot. The Sensor Pad cord must always be kept out of
reach of baby and secured using the cord cover kit provided.
PLEASE FOLLOW THE INSTRUCTIONS CAREFULLY FOR CORRECT SETUP
Please DO NOT return this product to the store. For assistance please
contact our helpline on 0845 009 1789 or email helpline@babyhelpline.co.uk
Mon – Fri 10am – 4pm, excluding bank holidays.
TABLE OF CONTENT
Warning
Warnings.....................................................................................3
AC701 SETUP REQUIREMENTS.......................................................8
STEP 1 - Charging the Parent Unit (15 hours).............................9
1. THIS PRODUCT CANNOT REPL ACE
RESPONSIBLE ADULT SUPERVISION. This
product is designed to aid in the monitoring
of your child. When using the monitor, you
must still provide the supervision necessary
for the continued safety of your child.
Monitoring of premature babies, or those
considered to be at risk, should always
be carried out under the supervision of a
health professional. This monitor SHOULD
NOT be used as a medical device, nor as
a device to prevent Sudden Infant Death
Syndrome (SIDS).
STEP 2 - Installing the Sensor Pad............................................... 10
STEP 3 - Setting up the Nursery Unit.......................................... 13
STEP 4 - Turning on your Monitor................................................ 14
STEP 5 - Testing and getting to know your monitor.............. 15
STEP 6 - A
ctivating and deactivating
additional functions......................................................... 19
Troubleshooting................................................................................. 25
Limited Warranty................................................................................27
Technical specifications................................................................... 28
OWNER’S MANUAL
KEEP YOUR OWNER’S MANUAL FOR FUTURE REFERENCE.
PLEASE READ THE WARNINGS AND INSTRUCTIONS CAREFULLY BEFORE
ASSEMBLING & USING THE PRODUCT.
FAILURE TO FOLLOW THE WARNINGS AND THE INSTRUCTIONS COULD RESULT
IN SERIOUS INJURY OR DEATH OR DAMAGES TO THE PRODUCT.
The Sensor Pad feature is not FOR USE WITH ADULTS, CHILDREN OR INFANTS
OLDER THAN 24 MONTHS.
The Sensor pad is not intended to be used to determine if a child is out
of the crib.
2. WARNING Strangulation Hazard —
Children have STRANGLED in cords. Keep
adapter cords out of the reach of children
(more than 1 m away).
NEVER use Sensor
Pad(s) without the
protective
cord
covering.
Check
protective
cord
covering before each
use. Immediately
discontinue use of
Sensor Pad(s) if protective covering is
damaged or broken.
3. Never use extension cords with AC
adapters. ONLY use the AC adapters
provided.
4. When an AC Adapter is plugged into
an electrical outlet, DO NOT touch the
exposed end.
Warning
Adult assembly required.
Keep small parts away from children when assembling.
5. ALWAYS be sure that both the transmitter
and receiver are working properly and are
within range of each other. Test monitor
before first use, periodically and when
changing location of the Nursery Unit.
6. ALWAYS be sure to immediately check
on baby whenever an alarm sounds.
This Angelcare Monitor is a Personal Care Product. Please DO NOT return this to the store
where you purchased it from. If you have any questions or require assistance please call the
Angelcare Helpline on 0845 009 1789 or email helpline@babyhelpline.co.uk.
7. DO NOT use monitor near water (such
as bath tub, sink, etc.).
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
DO NOT EXPOSE TO RAIN OR MOISTURE
8. Keep monitor AWAY from heat sources
(such as stoves, radiators, etc.).
9. ALWAYS place both the Nursery Unit and
Parent Unit on a flat surface in an upright
position and allow for proper ventilation.
DO NOT place on sofas, cushions, beds,
etc. which may block ventilation.
10. This monitor uses public airwaves to
transmit signals. The Parent Unit may
pick up signals or inter ference from
other nursery monitors in your area. Your
monitor may even be picked up by other
households. To protect your privacy, make
sure both units are turned OFF when not
in use.
11. This product is NOT a toy. DO NOT allow
children to play with it.
12. This product contains small parts. Adult
assembly required. Exercise care when
unpacking and assembling the product
and keep small parts away from children.
13. When using the monitor, the room
temperature should be between 10 °C and
40 °C.
BATTERY WARNING
14. Use O N LY A A A R EC HARG E AB LE
batteries for the Parent Unit. DO NOT
mix old and new batteries. DO NOT
mix alkaline, standard or rechargeable
batteries. Insert batteries with correct
polarity. DO NOT short-circuit supply
terminals. ONLY use the recommended
batteries or equivalent (volts and size)
and the correct adapter. Remove batteries
The Baby Helpline is open Monday to Friday, 10am to 4pm. The helpline is closed on bank
holidays.
For additional FAQs and to download instruction manuals visit; www.angelcare.co.uk.
To order spare parts for your Angelcare Baby Monitor visit; www.megababy.co.uk.
2
UK0314
3
when product is stored for long periods
of time or when batteries are exhausted.
Dispose exhausted batteries properly. DO
NOT recharge non-rechargeable batteries.
Rechargeable batteries are ONLY to be
charged under adult supervision. Keep all
batteries away from children.
15. Important Safety Instructions
15.1 Read these instructions - All the safety
instructions should be read before the
product is operated.
15.2 Keep these instructions. The safety
and operating instructions should be
retained for future reference.
15.3 Heed all warnings – All warnings on the
product and in the operating instructions
should be adhered to.
15.4 Follow all instructions – All operating
and use instructions should be followed.
15.5 Water and moisture - DO NOT use
this apparatus near water. For example,
near a bath tub, wash bowl, kitchen sink,
laundry tub, in a wet environment or near a
swimming pool and the like. Care should be
taken so that objects do not fall onto units
and that liquids are not spilled into either
unit or Sensor Pad through its openings.
15.6 Cleaning - Disconnect all units before
cleaning. DO NOT immerse in water any
part of the Nursery Unit, Parent Unit, or
Charging Cradle. Clean only with dry cloth.
DO NOT spray with cleaning products or
solvents. Wipe Sensor Pad with a cloth
moistened very slightly with an antiseptic
or mild detergent.
15.7 Ventilation - DO NOT block any
ventilation openings. Allow for proper
ventilation when units are in use. DO NOT
cover the Nursery Unit or Parent Unit with
any object such as a blanket. DO NOT place
it in a drawer or in any location which
would muffle the sound or interfere with
the normal flow of air.
15.8 Heat sources - DO NOT install near
any heat sources such as radiators, heat
registers, stoves, TVs or other apparatus
(including amplifiers) that produce heat.
Heat can damage the case or electrical
parts.
4
15.9 Power cord protection - Protect the
Sensor Pad cord and Adapter’s power
cord from being walked on or pinched by
furniture or other items – Power supply
cords should be routed so that they are not
likely to be walked on or pinched by items
upon or against them, paying particular
attention to cords and plugs, convenience
receptacle, and the point where they exit
from the product.
15.10 Accessories - Only use attachments/
accessories specified by the manufacturer.
DO NOT place this product on an unstable
cart, stand, tripod, bracket or table. The
product may fall, causing serious injury
to a child or adult and serious damage to
the product. Use ONLY with a cart, stand,
tripod, bracket or table recommended by
the manufacturer or sold with the product.
Any mounting of the product should follow
the manufacturer’s instructions.
15.11 Unplug this appliance during lightning
storms or when not used for long periods
of time.
15.12 Ser vicing - DO NOT attempt to
service this product yourself as opening
or removing covers (except battery covers)
may expose you to dangerous voltage or
other hazards.
15.13 R e p l a c e m e n t p a r t s - W h e n
replacement parts are required, be sure
the replacement parts specified by the
manufacturer have the same characteristic
a s th e o r i g i n a l p a r t . U n a u th o r ize d
substitution may result in fire, electric
shock or other hazards.
15.14 U s a g e - This b a by m o nito r is
intended as an aid. It is NOT a substitute for
responsible and proper adult supervision
and should not be used as such. Use this
appliance ONLY for its intended use as
described in this manual.
15.15 Powe r S o u rce s - O p e rate th is
product only from the type of power
source indicated on the type plate of the
adaptor. If you are unsure of the type of
power supply to your home, consult your
dealer or local power company.
15.16 Overloading - DO NOT overload
wall outlets, extension cords or integral
convenience receptacles as this can result
in a risk of fire or electric shock.
15.17 Object and Liquid Entry - NEVER
push objects of any kind into this product
through casing slots as they may touch
dangerous voltage points or short out
parts that could result in a risk of fire or
electric shock. NEVER spill liquid of any
kind on the product.
15.18 Antenna - The antenna used for this
transmitter must be installed to provide a
separation distance of at least 20 cm from
all persons and must not be collocated or
operating in conjunction with any other
antenna or transmitter.
15.19 Power Lines - An outside antenna
system should NOT be located in the
vicinity of overhead power lines or other
electric light or power circuit, or where it
can fall into such power lines or circuits as
contact with them may be fatal.
15.20 WARNING Strangulation Hazard —
Children have STRANGLED in cords. Keep
adapter cords out of the reach of children
(more than 1 m away).
NEVER use Sensor
Pad(s) without the
protective
cord
covering.
Check
protective
cord
covering before each
use. Immediately
discontinue use of
Sensor Pad(s) if protective covering is
damaged or broken.
You may experience false alarms for several
reasons. The most common reason is the
Nursery Unit has not been turned OFF after
you have removed your baby from the crib.
Another reason is the Sensor Pad has not
been placed under the mattress properly.
Be sure the Sensor Pad is on a flat, firm
surface with the printed side facing up.
The sensitivity level may also need to be
adjusted. Refer to step 5.1. Always be sure
to immediately check on baby whenever
an alarm sounds.
15.23 Sensor Pad - If the crib has a
spring or slat base, place a hard board
between the crib base and the Sensor Pad
measuring at least 33 x 33 cm and 6 mm
thick. Only use your Angelcare ® monitor
in a stationary sleeping environment such
as a crib where the Sensor Pad can rest
on a completely flat, firm surface. ALWAYS
route the Sensor Pad cord below crib
mattress and out of reach of children.
15.21 Interference - This monitor uses
public air waves to transmit signals .
The Parent Unit may pick up signals or
interference from other nursery monitors
in your area. Your monitor may even be
picked up by other households. To protect
your privacy, make sure both units are
turned OFF when not in use.
15.22 Vibration Source - When the monitor
is in use, DO NOT use a crib mobile or
other crib accessories that may produce
vibrations. Other sources of vibrations
may include fans, washing machines, loud
music, etc. These sources of vibration may
interfere with the performance of your
Angelcare ® monitor and the alarm will
not sound if it continues to detect any
movement other than your baby’s. Be sure
all vibration sources are eliminated before
using the monitor.
5
16. IMPORTANT SAFETY INSTRUCTIONS
RELATED TO USE OF BATTERIES
16.1 Use O N LY the t ype and size of
batteries specified in the owner’s manual.
There is a risk of explosion if batteries are
replaced with an incorrect type.
16.2 U s e O N LY A A A r e c h a r g e a b l e
batteries and/or the AC Adapters provided
for the Parent Unit. You must use only
rechargeable batteries in the Parent Unit.
DO NOT use alkaline batteries or you will
severely damage the unit.
16.3 Charge the batteries for 15 hours prior
to first use. Be sure to have the monitor in
the OFF position during this period. ONLY
use the AC Adapters included with your
monitor.
Warning
16.9 DO NOT attempt to recharge batteries
provided with or identified for use with
this product that are not intended to be
charged. The batteries may leak corrosive
electrolyte or explode.
16.10 DO NOT attempt to rejuvenate the
batteries provided with or identified for
use with this product by heating them.
Sudden release of battery electrolyte may
occur, causing burns or irritation to eyes
or skin.
16.4 DO NOT use these adapters with any
other equipment.
16.11 If and when necessary, the batteries
must be replaced with identical new ones
or equivalent (volts and size). If a battery
to be replaced is connected with other
batteries in series, replace the other
batteries at the same time as well. DO
NOT mix old and new batteries.
16.5 When unplugging the AC Adapter
from the Nurser y Unit, be sure it is
switched to the OFF position. If it isn’t, the
unit will revert to battery mode if batteries
are installed.
16.12 Reverse polarity installation of the
batteries in the end product must be
avoided. Reverse insertion of batteries
can cause charging, and that may result
in leakage or explosion.
16.6 DO NOT use rechargeable batteries
in the Nursery Unit. Use alkaline batteries
ONLY.
16.13 Remove batteries from this product
if you store the product over 30 days
because the batteries could leak and
damage the product.
16.7 DO NOT dispose batteries in fire. They
may explode. Check with local regulations
for possible special disposal instructions.
16.8 Exercise care in handling batteries
in order not to short out the batteries
with conducting materials such as rings,
bracelets and keys. Overcharging, short
circuiting, reverse charging, mutilation, or
incineration of batteries must be avoided
to prevent one or more of the following
occurrences: release of toxic materials,
release of hydrogen and/or oxygen gas,
rise in surface temperature.
16.14 Discard ‘dead’ batteries as soon as
possible since ‘dead’ batteries are more
likely to leak in a product. If a battery has
leaked or vented, it should be replaced
immediately using protective gloves.
(North America Only)
17. Modifications not authorized by the
manufacturer may void users authority
to operate this device.
17.1 NOTE : This equipment has been
tested and found to comply with Part 15
of the FCC Rules and the Industry Canada
licence-exempt RSS standard(s). These
limits are designed to provide reasonable
protection against harmful interference in
a residential installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed and
used in accordance with the instructions,
may cause harmful interference to radio
communications.
17.3 This d evice co m plies with pa r t
15 of the FCC Rules and the Industry
Canada licence-exempt RSS standard(s).
Operation is subjected to the following
two conditions:
1) This device may not cause harmful
interference, and
2) This device must accept any
interference received, including
interference that may cause undesired
operation.
17.2 However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment OFF and ON ,
the user is encouraged to try to correct
the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between
the equipment and receiver.
• Connect the equipment into an
outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
16.15 DO NOT store this product, or the
batteries provided with or identified for
use with this product, in high-temperature
areas.
FCC and IC regulations
RF radiation exposure statement
The Nursery Unit complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. Caution: To maintain the compliance with the FCC’s RF
exposure guideline, install the Nursery Unit at least 20 cm from nearby baby and persons.
For body worn operation, this Parent Unit has been tested and meets the FCC RF
exposure guidelines. Use of accessories may not ensure compliance with FCC RF exposure
guidelines.
Industry Canada
This product meets the applicable Industry Canada technical specifications.
CAN ICES-3 (B)/NMB-3 (B)
6
7
TOUCHSCREEN MOVEMENT
SETUP REQUIREMENTS
& SOUND MONITOR
STEP 1 - Charging the parent unit (15 hours)
Model AC701
INCLUDED:
5
6
Rechargeable
Parent Unit
Charging Cradle
3
4
2
Warning
Never use regular
alkaline batteries
in the Parent Unit;
they may explode.
1
1
1) Slide the button to unlock and open the
battery cover. Insert the Rechargeable
Batteries (included) as per picture.
1 Sensor Pad (AC701) or 2 Sensor Pads (AC701-2SP)
with pre-installed cord covers
2
Nursery Unit
2) Connect the AC Adapter to the Parent
Unit and into an electrical outlet.
2X
2X
Belt Clip
3
2 AC Adapters
15
3) Charge the unit for 15 continuous
hours (prior to first use).
Note:
2 AAA Rechargeable
Batteries
for Parent Unit
To optimize your battery performance please
refer to Battery Guidelines in the Trouble
Shooting.
What you will need (not included):
You must prepare:
One hardboard (not included)
Thickness: 6 mm
Minimum dimensions:
33 cm x 33 cm
Maximum dimensions:
equal to the mattress size
Hardboard
PARENT UNIT:
2X
Important
The hardboard must be larger than the
Sensor Pad surface area or in the case
of the AC701-2SP of two Sensor Pads.
2 AA Alkaline
Batteries
for Nursery Unit
A)LCD Touchscreen
Miniature Phillips
Screwdriver
F
A
B)POWER ON/OFF
C)Microphone
B
G
D)Speaker
E)Charging Cradle
H
Important
Place the crib near a supporting wall and
far from air currents. Install the Nursery
Unit on a flat, stable surface facing the
crib at a distance of at least 1 meter.
BABY’S ROOM:
F)Belt Clip
G)Speaker
Volume Buttons
C
H)Talk Back Button
D
I) Battery Cover
(not shown)
I
E
J
J) AC Adapter Outlet
(not shown)
Important
Keep
at least
1m
apart
6
5
8
Sensor Pad
4
3
2
Front View
Right Side View
1
9
STEP 2 - INSTALLING THE sensor pad
2.2 Select the crib leg you will be using to secure the cord covers
Recommended
6
5
3
4
2
1) Use the crib leg by the wall closest to
the Nursery Unit (Fig 1). In cases where
the Nursery Unit is across the room, use
the leg closest to the Nursery Unit to
position the covered wire (Fig 2). It is
always preferable that the covered cord
run along a wall.
Cord covers 1, 2, 3, 4:
Position on floor
1
Cord cover 4:
Contains double sided
tape to securely install
beneath crib leg
6
5
4
Cord cover 5:
Position vertically
between mattress
support and floor
Sensor Pad with pre-installed cord covers
3
2
Fig 1
1
OR
Cord cover 6:
Place under
the mattress
WARNING
6
Strangulation Hazard.
Children have been strangled by cords.
•Keep adapter cords out of the reach of children
(more than 1 m away).
•Because of the serious strangulation risk to infants
and toddlers, parents and caregivers should never
place the Nursery Unit within 1 m of a crib.
•NEVER use Sensor Pad without the cord covers.
Check cord covers before each use to ensure it is
securely placed under the leg of the crib. Discontinue
use of Sensor Pad if any cord covers are damaged or
broken.
•NEVER use extension cords with AC adapters. ONLY
use the AC adapters provided. This product is not a
toy. Never allow children to play with it.
1
2
5
4
3
Fig 2
2.3 - INSTALL THE SENSOR PAD ON THE MATTRESS SUPPORT
3
1) Remove the mattress from the crib.
6
5
2) Place the Sensor Pad - printed side up
- on top of the hardboard at the center
of the crib.
4
3
2
1
3) Run the connection pin, warning label
and the first 5 cord covers down along
the backside’s of the crib leg, between
the mattress support and the inside
edge of the crib.
4) Bring the first 4 cord covers down
the floor, and keep the 5th cord cover
vertically, along the backside of the crib
leg, (between the mattress and the
inside edge of the crib).
2.1 - Select a location for the Nursery Unit
Select a location for the Nursery Unit that
is at least 1 m away from the crib.
4
5
5) Remove any cord slack to make sure
no parts of the cord are loose.
Important
Keep
at least
1m
apart
6
5
4
3
2
5
1
Sensor Pad
10
11
6
STEP 3 - Setting up the Nursery Unit
8 cm
1
6
1) Unscrew the battery cover and
insert 2 AA Alkaline Batteries
(not included).
6) Place the 6th cord cover approximately
8 cm from the edge of the mattress
support.
7
3) Connect the AC Adapter to the Nursery
Unit and plug into an electrical outlet.
7) Snap together the remaining cord
covers that will run along the floor.
CLIC!
4
2) Place the Nursery Unit at a minimum
of 1 m away from the crib.
8) Remove any cord slack to make sure
no parts of the cord are loose.
3
2
8
1
9
9) Peel off the double-sided tape on the
4th cord cover and place it securely
under the crib leg.
10)Install the Nursery Unit on a flat, stable
surface facing the crib at a distance of
at least 1 m and plug the Sensor Pad
cord into the Nursery Unit.
Note:
3
2
The batteries maintain power
supply in case of power outage.
IMPORTANT
Keep at least
1m
apart
6
5
4
3
2
1
11) Check to make sure the Sensor Pad has
not moved from position.
4
3
2
1
12)Place the mattress back inside the crib.
NURSERY UNIT:
A)Night Light
10
B)Hold/Pager Button
The Sensor Pad functions with any size
and type of mattress except memory-foam
mattresses and hollow frame mattresses.
C)POWER ON/OFF
(Left ‘Wing’)
A
D)Night Light ON/OFF
(Right ‘Wing’)
The hardboard maintains a constant
pressure on the Sensor Pad, enabling it to
detect the baby’s movements even when
the baby is at the edges of the crib.
E)Power Indicator (green)
Low Battery Indicator (red)
Hold indicator
(green flashing)
B
C
D
E
F
WARNING
Strangulation Hazard
• Remove all slack from Sensor Pad Cord.
• When lowering the mattress support
as your child grows, slide the vertical
Cord Cover (5) upward so it remains
approximately in the center between
the mattress support and the floor. Slide
the Sensor Pad Cord through the Floor
Cover to eliminate any additional slack.
12
• The Sensor Pad is not designed for use
with adults, children or infants older
than 24 months.
• Discontinue used of the Sensor Pad
when child is older than 24 months.
Remove sensor pad from crib and store
for future use.
• BEFORE FIRST TIME USE: To test
that the unit is ready for use, refer to
instruction manual on how to test that
the installation has been done
G
H
F)Movement Indicator (green)
Alarm Indicator (red)
I
G)Microphone
J
H)Speaker
K
I) Sensor Pad Outlet
J) AC Adapter Outlet
L
Front View
Rear View
K)Nursery Unit Switch
Mode 1 - Standard Mode
Mode 2 - Movement Only
L) Battery Cover
(not shown)
13
STEP 4 - Turning ON your Monitor
2
1
STEP 5 - Testing and getting to know your monitor
1) Press the Parent Unit ON/OFF button
to open and display normal mode.
The Angelcare® monitor can be used with the pre-program factory settings
or you can also customize your settings to your preference.
2) Push and hold the Nursery Unit
left ‘wing’ button for 2 seconds.
Note: All changes
and adjustments made
in the settings mode will
not be activated unless
you confirm them by
pressing the Return icon.
A long beep will confirm
your modification.
The LCD monitor has 30 seconds
timeout to go to power saving
mode (dimmer illumination).
Press any keys to wake up.
Important
When in settings mode, sound
transmission between Parent and
Nursery Units will be temporarily
deactivated. ONLY the movement
alarm will remain active
(if function is activated).
5.1 - SENSOR PAD
When the Parent Unit is turned
ON and the Nursery Unit is OFF,
the Parent Unit will be searching
for connection with the Nursery
Unit. The Connection icon will scan
as the following cycle.
If there is a lost connection
between the 2 units
(refer to troubleshooting):
TO Activate the Sensor pad:
1) Press Sensor Pad icon to activate
or deactivate movement mode.
1
ON
• The Out-of-Range icon
will appear on the screen and
the Parent Unit will beep.
OFF
When the movement mode is OFF
the ‘TIC’ mode is automatically set OFF.
This allows you to detect the baby’s
sounds ONLY.
TO TEST THE Sensor pad:
1) Move your hand lightly on the mattress.
Important Icons
Temperature icon:
Indicates room temperature
Sound icon: Indicates sound
is active
Battery Level icon:
Indicates battery level
Sensor Pad icon: Indicates
the Movement Sensor is active
Empty
Pendulum icon: Indicates
the ‘TIC’ function is active
1/3 Full
Level Bar: Indicates sound level
from Nursery Unit.
2/3 Full
Full
Connection icon: Indicates
the connection quality between
the Parent Unit and Nursery Unit.
Settings Icons: Access to settings
VOX icon: Indicates Vox function
is active (Voice activation)
ECO icon: Indicates ECO function
is active
Temperature Alarm icon: Indicates
Temperature Alarm is active
14
1
Good connection
Fair connection
Poor connection
Out-of-Range
2
2) Remove your hand from the mattress.
After 15 seconds you will hear a
‘TIC’ pre-alarm sound, and 5 seconds
later the Movement Alarm will trigger.
3) Repeat by moving your hand lightly
in all four corners of the mattress.
Ensure the Nursery Unit Movement
Indicator is still flashing.
Movement alarm
• Alarm activates when no movement is detected by Sensor Pad for 20 seconds.
• Both the Parent Unit and Nursery Unit speakers will emit loud warning sound.
• Movement Alarm icon will show on the LCD screen.
If the alarm does not sound
• Avoid contact with crib while Sensor Pad is in operation.
• Place crib near a supporting wall.
• Adjust the Sensor Pad sensitivity level.
15
To stop the alarm
OR
5.2 - SOUND
OR
Press Nursery
Unit’s Hold button
(see step 6.5)
Press any key on
the Parent Unit
to put on Hold
(see step 6.5)
Hold down left ‘wing’
button for two seconds
to turn OFF the Unit
Place your
hand back
on the mattress.
To adjust THE SENSOR PAD sensitivity level:
1
4
1) Press Settings icon to access setting mode.
Level 1
Raise volume
level (+)
Press + or - buttons to adjust
the volume level.
Lower volume
level (-)
NOTE:
At level L0 the level bar will still appear on
the screen and the icon will blink. If you press
the blinking sound icon again, it automatically
activates the Mute function. The Bar will disappear
and a cross will appear in the icon screen.
To DEACTIVATE, press the sound icon again.
(Refer to 6.6 for more information on Mute mode).
Level 2
Level 3
Level 4
Level 5
2) Press Movement Sensitivity icon.
The icon will blink.
2
Level 0
TO ADJUST THE SOUND:
TO LOWER VOLUME LEVEL TO L0
3) Use the (+) or (-) on the right side of
the Parent Unit to choose the desired
sensitivity level (1 to 5) OR press the
movement sensitivity icon
to choose the desired sensitivity level.
Put in TALK BACK mode
Press the
(-) button
to select the
L0 level
(see step 6.6)
4) Press Return icon to confirm your choice
and return to normal screen.
Press and hold
the Talk Back
button to speak
to your baby.
Level 1
Level 2
3
Note:
Level 3
If you are receiving false alarms,
adjust the sensitivity level.
Level 4
Note:
Level 5
Whilst in Setting mode, if after 30 seconds
no adjustments are made, the unit will go back
to normal and no update will be done.
TO TEST THE SOUND:
Ask someone to speak into the Nursery
Unit or place the unit near a radio to ensure
that sound is being picked up.
Important
To avoid feedback (whistling), keep
both units at least 3 m apart.
TO ACTIVATE THE Tic function:
This allows you to hear a ‘TIC’ sound with baby’s movements
(when the movement detection is ON)
1) Press TIC icon to activate
or deactivate the ‘TIC’ function.
1
Note:
When the Movement Mode
is set to OFF, the TIC Mode
is automatically set to OFF.
• Check that both units are switched on.
• Check that both units are plugged
into a working electrical outlet.
• Check the batteries in both units
(replace or recharge them as necessary
per unit).
• Bring the Parent Unit closer to the
Nursery Unit.
5.3 - BATTERIES
HOW TO CHECK THE BATTERIES:
Unplug the AC Adapters from both units.
ON
OFF
If the TIC icon is activated a regular TIC
sound will emit from Parent Unit.
Note:
When using ECO mode, the TIC function
shuts off.
Important
• The Sensor Pad is not designed for use with adults, children or infants older
than 24 months.
• Once you are finished using the Sensor Pad, please remove it from the baby’s
crib and store it away.
16
If you hear no sound:
• If the green light on the Nursery Unit does not show, replace the batteries.
• If the Parent Unit and its screen do not light up, recharge the batteries.
HOW TO CHARGE THE BATTERIES IN THE PARENT UNIT:
Leave the Parent Unit in the Charging Cradle
to fully charge the unit. Although the batteries
at 1/3 capacity works normally, we recommend
that you fully recharge them.
1/3 full
2/3 full
full
PARENT UNIT BATTERY ALARM
• Alarm activates when batteries need to be recharged.
• Parent Unit will emit a beep sound every 20 seconds.
• Battery icon will flash on Parent Unit screen.
17
YOU ARE NOW READY
TO USE YOUR MONITOR
STEP 6 - Activating and deactivating additional functions
The Angelcare® monitor can be used with the pre-program factory settings
or you can also customize your settings to your preference.
The Angelcare® monitor is multifunctional. It can be use in different combinations
according to your needs.
MULTIFUNCTIONAL
SOUND & MOVEMENT:
Allows you to detect the baby’s
movement & sound while using both
Parent Unit and Sensor Pad.
Default settings
1
2
Slide the Nursery Unit Connecting
switch to 1 to detect sound
and movement.
Sound Mode: ON
Speaker Volume: Level 3 (of 5)
Movement Only:
Movement Mode: ON
Sensor Pad Sensitivity: Level 3 (of 5)
TIC: OFF
Allows you to detect the baby’s movement ONLY
without the Parent Unit. This combination can be useful
when the baby is in the same room as the parents.
Temperature Alarm: OFF
Temperature Alarm Settings:
High Temperature Limit*: 30 °C
Low Temperature Limit*: 19 °C
1
2
VOX Mode: OFF
VOX Level: Level 2 (of 4)
Slide the Nursery Unit Connecting switch
to 2 to detect movement ONLY. If the
Parent Unit is turned on, the Parent Unit
will only display the Out-of-Range icon.
ECO Mode: OFF
Sound Only:
Alarm Mode: Sound alarm only
Allows you to detect the baby’s sound ONLY without
the Sensor Pad. This combination can be useful if you
don’t want to use the Sensor Pad or if your baby is older
than 24 months (maximum age to use the Sensor Pad).
1
* High/Low Temperature Setting
preset values might be different
for various countries.
2
Slide the Nursery Unit Connecting switch to 1
to detect sound ONLY (Sensor Pad function
needs to be deactivated on the Parent Unit then
unplugged from the Nursery Unit).
Note:
To safely store just make sure to remove the Sensor Pad and cords
from the crib – disconnect sensor cord plug from the nursery unit
and safely store away in box for future use.
Note:
By doing the re-connection procedure you will reset
the monitoring system back to original presets.
The Angelcare® monitor can be used with the pre-program factory settings
or you can also customize your settings to your preference.
Note:
Important
• Test your monitor before first use.
• Test your monitor regularly to ensure it is functioning correctly.
• Test your monitor every time you move the Sensor Pad to a different place.
18
All changes and adjustments
made in the settings mode
will not be activated unless
you confirm them by pressing
the Return icon.A long beep
will confirm your modification.
Important
When in settings mode, the sound
transmission between the Parent
and Nursery Unit will be temporarily
deactivated. ONLY the movement
alarm will remain active
(if function is already activated).
19
6.1 - Voice Activation (Vox) OR CONTINuOUS SOUND MODE
6.2 - ECO MODE
Allows you to select your option on how you monitor sound:
Allows you to reduce the electro-smog and save battery life.
VOX (voice activation picks up sound based on the selected sensitivity level settings) or
Continuous (sound monitoring is continuously on, picking up all sounds).
TO ACTIVATE ECO mode:
3
1
1
1) Press the VOX icon to activate
or deactivate the VOX function.
VOX ON
(VOX)
1) Press the Settings icon to access
setting mode.
2
2) Press the ECO icon to activate
or deactivate the ECO function.
VOX OFF
(Continuous)
ON
3) Press the Return icon to confirm your
choice and return to normal screen.
Note:
By deactivating VOX, the Continuous sound
setting is ON.
The ECO icon will appear next
to the Connection icon when
the function is active. Note that
range bar will not appear.
TO Adjust THE VOX sensitivity:
Allows you to determine the sound level needed to trigger sound transmission
to the Parent Unit.
1
OFF
Note: In ECO mode, the transmission is greatly
reduced. Vox automatically turns on and TIC
feature shuts off, but the Movement, Sound
and Temperature alarms will remain working
as selected.
4
2
1) Press the Settings icon to access
setting mode.
6.3 - TEMPERATURE CONTROL
2) Press the VOX Sensitivity icon.
The icon will blink.
3) Use the (+) or (-) on the right side
of the Parent Unit to choose the desired
sensitivity level (1 to 4)
OR
press vox sensitivity icon to choose
the desired level.
Level 1
To change the measurement unit:
1
4
2
2) Press the Temperature setting Icon.
4) Press Return icon to confirm your choice
and return to normal screen.
3) Press the Talk button on Parent Unit
to change from Celsius to Fahrenheit.
Level 2
3
Level 3
Level 4
1) Press the Settings icon to access
setting mode.
Note:
Celsius
When using ECO mode, the monitor will
automatically switch to VOX setting.
Fahrenheit
4) Press the Return icon to confirm your
choice and return to normal screen.
3
20
21
6.4 - Alarm
TO Activate THE temperature alarm:
Allows you to select your preferred alarm mode for the Parent Unit.
1
1) Press the Settings icon to access
setting mode.
3
1
1) Press the Temperature Alarm icon
to activate or deactivate the high
and low temperature alarm.
ON
2) Press the Alarm icon, current alarm mode
icon will blink. Then press again to select
the alarm mode as the display changes
for various modes.
2
OFF
3) Press the Return icon to confirm your
choice and return to normal screen.
Sound alarm
and vibration
TO Set temperature range:
1
Sound alarm only
Vibration only:
When the movement alarm is triggered, the Parent Unit will vibrate
and a sound alarm will be heard on the Nursery Unit.
6
1) Press the Settings icon to access
setting mode.
2
4
2) Press the Temperature Alarm icon.
3) High Temperature (SUN) icon will blink,
press (+) or (-) to set the high
temperature alarm (22 to 35 °C).
3
5
When the Parent Unit is on
the charger, the sound alarm will
replace the vibration mode.
Important
When in setting mode no sound or alarms will transmit to the Parent Unit,
except the movement alarm (if this function was already activated).
4) Press the Temperature Alarm icon again.
6.5 - Hold
5) Low Temperature (SNOWFLAKE) icon
will blink, press (+) or (-) to set low
temperature alarm (5 to 19 °C).
Allows you to put your Angelcare Monitor on HOLD.
6) Press the Return icon to confirm
your choice and return to normal screen.
High
Temperature
1
1) Press the Setting icon to access
the setting mode.
2) Press the Hold icon
OR
Press the Nursery Unit Hold button
for 4 seconds.
Low
Temperature
2
Temperature alarm
• Alarm activates when the temperature reaches a maximum or minimum
set temperature.
• Parent Unit will emit 3 consecutive beeps and/or vibrate every 5 seconds
depending on the type of alarm chosen.
• Temperature Alarm icon will show on LCD screen with the Low/High
icon blinking.
3) Press the Hold icon for 4 seconds or
the Nursery Unit Hold button again
to return to normal operation.
2
Note:
When on HOLD, the Nursery Unit Power Light will
blink. The Parent Unit will emit beeps and/or vibrate
every 20 seconds to remind you that monitor is on
hold, depending on the type of alarm chosen.
Important
When your monitor is on hold, the movement feature and Movement alarm are disabled.
22
23
6.6 - MUTE
Troubleshooting
Allows you to activate the MUTE function.
Taking Care of your Rechargeable Batteries
TO ACTIVATE MUTE:
Press the Sound Icon.
ON
OFF
TO DEACTIVATE MUTE:
Press the Sound Icon to deactivate.
Note:
The MUTE icon will blink
on the Parent Unit.
6.7 - NIGHT LIGHT
Loss of connectivity
OR
Allows you to use your monitor as a night light.
• Ensure that you fully charge your batteries for 15 hours before their first use.
• To maintain maximum battery life it is recommended that you fully discharge
your batteries periodically. Battery performance can be diminished by leaving
the batteries constantly charging on the charging cradle. If your parent unit is not
in use, please turn it off.
• Inadequate battery power can impair the performance of your monitor. If you are not
happy with the performance of your Parent Unit/Monitor please replace the
rechargeable batteries (2 x NiMH Rechargeable Batteries).
• It is advisable to change the batteries every 6 months.
In the case of loss of connectivity, the first step is to bring the Parent Unit and Nursery Unit
closer together and make sure that both units are ON to restore the connection. If there is
still no connection and no out of range warning after the above has been done, then and
only then should the re-connection procedure below be done.
To ACTIVATE the light:
Push the right ‘wing’ of the Nursery Unit or press
the Night Light icon on the Parent Unit to select
light level.
1
Note:
Re-connection procedure:
2
1) Turn on the Parent Unit and hold the
Talk button down for 2 seconds until
the Nursery Unit icon shows at the
center of the screen.
The Night Light function will be disabled
if the Nursery Unit is in battery mode.
OFF
Low
High
2) By pressing the Nursery Unit Icon
button the Parent Unit will be set in
to connectivity mode (the icon will
flash).
6.8 - Pager
Note:
Allows you to locate the Parent Unit.
TO LOCATE Parent Unit:
Press and release the Nursery Unit Pager button.
The Parent Unit will emit a paging sound
for one minute.
3
4
Make sure the Nursery
Unit Connecting switch
on the back of the unit
is in the position 1.
1
TO STOP THE PAGING SOUND:
5
2
After 1 minute of non-operation, the Parent
Unit will exit the connectivity mode and you
will need to start this process again.
3) Press the Power button to turn on
the Nursery Unit. The Power LED
will light.
4) Then press the Power button 4 times
within 30 seconds. The Power LED will
blink. The connection procedure should
be completed within 10 seconds.
5) When the Parent Unit and Nursery
Unit are connected, H1 (or H2)
will be displayed on the Parent Unit
and then be followed by the normal
mode screen.
Note:
Press the Parent
Unit screen
or any buttons
24
OR
Press the Nursery
Unit’s Page button
By doing the re-connection procedure you
will reset the monitoring system back to
original presets.
25
FALSE ALARMS
• Turn OFF the Nursery Unit.
• Verify the connection between Sensor Pad and Nursery Unit.
Unplug and reconnect the cord.
• Make sure there is no bedding between mattress and Sensor Pad.
• If the crib has a spring or slat base, place a hardboard between the crib base
and the Sensor Pad measuring at least 33 x 33 cm and 6 mm thick.
• Make sure Sensor Pad is positioned as described under the setup requirements.
Sensor Pad Sensitivity level may need to be adjusted, refer to step 5.1.
THE PARENT UNIT SCREEN IS BLACK (PARENT UNIT IS OFF)
• Turn the Parent Unit back ON by pushing and holding the Power button.
• Replace the batteries or recharge the Parent Unit.
ALARM WILL NOT SOUND
• Avoid contact with the crib when the monitor is ON.
• Place crib near a solid supporting wall to avoid Sensor Pad from detecting movement
from outside the crib.
• You may need to decrease the sensitivity, refer to step 5.1.
• Turn OFF crib mobile, fans, loud music or anything else that may cause vibration.
NO SOUND IS BEING TRANSMITTED
• Ensure that both units are switched ON.
• If there is no power to any unit check/replace the batteries, recharge the Parent Unit
& check the AC Adaptors are working. Change electrical outlets if required.
• Check on the Parent Unit screen to see if the monitor is in MUTE mode instead of ON
mode. Refer to step 6.6. and increase volume level.
• Bring the Parent Unit and Nursery Unit closer together.
NURSERY UNIT POWER ON INDICATOR (GREEN LIGHT) DOES NOT LIGHT UP
Limited Warranty
Angelcare® warrants to the original owner of this product that Angelcare® rechargeable
TOUCHSCREEN MOVEMENT & SOUND MONITOR (model AC701) is free from any material
and workmanship defects, for a period of one (1) year (Rechargeable batteries not
included) from the date of the original purchase. If this monitoring system fails to function
properly when used as directed under normal conditions within the one year period,
Angelcare® will either repair or replace the product, at our discretion, free of
charge. Please contact your distributor.
The product must be accompanied by a proof of purchase, either a bill of sale or other
proof that the monitoring system is within the warranty period. Angelcare® will bear the
cost of repairing or replacing the product and shipping it back to you.
This warranty does not apply to a product which has been damaged as a result of
improper maintenance, an accident, improper voltage supply or any other form of
misuse. The warranty is also void if the owner repairs or modifies the product in any
way. Angelcare® is not liable for any incidental or consequential damages with regard
to this product. The warranty also excludes any liability other than what is stated above.
No other warranty is given.
• Check the connections or change to another electrical outlet.
• Push and hold the left ‘wing’ for 2 seconds to turn the Nursery Unit ON.
LEGAL RIGHTS VARY FROM COUNTRY TO COUNTRY. SOME COUNTRIES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
WEAK RECEPTION
WE ARE NOT IN ANY WAY RESPONSIBLE FOR ANY OUTCOME RESULTING
FROM THE USE OF THIS PRODUCT.
•
•
•
•
Bring the units closer together.
Change the position of one or both units.
Place the units on a flat surface away from baby’s reach.
Replace the batteries or recharge the Parent Unit.
IMPORTANT!
This Angelcare® monitor is a personal care product. Please do not return this product
to the store. If you have questions or need help, please call your distributor before
returning this product.
STATIC, DISTORTION, INTERFERENCES
(FROM OTHER MONITORS, WIRELESS PHONES, WALKIE-TALKIES, ETC...)
• Rotate the Parent Unit or move it away from source of interference.
FEEDBACK (LOUD NOISES EMITTED FROM THE PARENT UNIT)
• Move the units farther apart (at least 3 meters apart).
• Decrease volume on the Parent Unit.
26
27
Technical specifications
They may only be replaced by 2 AAA
NIMH rechargeable batteries.
Range:
Open field: up to 250 m
Batteries:
Power Supply:
2 AA Alkaline batteries (not included)
or 100-240VAC/5VDC Adapter
for Nursery Unit.
2 AAA rechargeable batteries and
100-240VAC/5VDC AC adapter for
Charging Base for the Parent Unit.
Caution: To reduce the risk of electric
shock, do not expose this product to rain
or moisture.
Risk of explosion if battery is replaced by
an incorrect type. Dispose of used batteries
according to the instructions.
Danger of explosion if batteries are
incorrectly replaced. The included Batteries
are 2 AAA NIMH rechargeable batteries,
manufactured by GPI INTERNATIONAL
LIMITED (GN60AAAHC, 1.2V 600mAh) or
by HIGHPOWER TECHNOLOGY CO., LTD
(HFR-44AAAJ600, 1.2V 600mAh).
• DO NOT mix old and new batteries.
• DO NOT mix alkaline standard
(carbon-zinc), or rechargeable
(NI-CD, NIMH, etc) batteries.
Transmission:
Data transmission between the Parent
Unit and Nursery Unit is made on a
frequency between 1880 and 1920 Mhz
(the exact frequency band varies
among countries).
Hereby, Angelcare Monitors Inc, declares
this baby monitor is in compliance with the
essential requirements and other relevant
provisions of Directive 1999/5/EC.
The EU declaration of conformity can be
obtained through your local distributor.
Please refer to address in the manual.
PROTECT THE ENVIRONMENT
This electronic equipment contains reusable material and must not be disposed
with domestic waste. Please take it to a collecting point for electric and electronic
equipment (ask your local authorities for details).
ErP COMPLIANCE
SOUTH AFRICA-BRAZIL-ECUADOR-EUROPEAN UNION-UK
Use only Angelcare® Brand power supply - model number: T05005V001 / T05005B001
GERMANY
Use only Angelcare® Brand power supply - model number: T05005F002
AUSTRALIA
Use only Angelcare® brand power supply - model number: T05005S002
NORTH AMERICA
Use only Angelcare® brand power supply - model number: T05005U002
28
29
30
31
This Angelcare Baby Monitor is a Personal Care Product. Please DO NOT return
this to the store, but contact us initially for advice and assistance:
Angelcare Helpline on 0845 009 1789
Website: www.angelcare.co.uk
Email: helpline@babyhelpline.co.uk
NOTE: Helpline is open Monday to Friday, 10am to 4pm, excluding bank holidays.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising