Sony XR C5100, XR 4800 car stereo Service manual
The XR-C5100 US Model, XR-C5100 Canadian Model, and XR-C5100 E Model car stereos are designed for use in vehicles. They feature a cassette player, an FM tuner, and a 4-channel power amplifier. The E Model also includes an AM and shortwave (SW) tuner. The XR-C5100 car stereos can be used to play music from cassette tapes, FM radio stations, and AM/SW radio stations. They can also be used to amplify the sound of external audio sources, such as a CD player or MP3 player.
Advertisement
Advertisement
SERVICE MANUAL
XR-C5100
US Model
Canadian Model
E Model
Model Name Using Similar Mechanism
Tape Transport Mechanism Type
XR-4800
MG-25F-136
Cassette player section
Tape track
Wow and flutter
4-track 2-channel stereo
0.08% (WRMS)
Frequency response
Signal-to-noise ratio
30 – 18,000 Hz
58 dB
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS (US model)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
17 watts per channel minimum continuous average power into 4 ohms,
4 channels driven from 20 Hz to 20 kHz with no more than 1% total harmonic distortion.
AM (MW)
Tuning range AM tuning interval:
530 – 1,710 kHz
(US, Canadian model)
MW tuning interval:
9 kHz/10 kHz switchable
531–1,602 kHz (at 9 kHz step)
530 – 1,710 kHz (at 10 kHz step)
(E model)
Antenna terminal External antenna connector
Intermediate frequency 10.71 MHz/450 kHz.
Sensitivity 30 µV
Tuner section
FM
Tuning range FM tuning interval:
87.5 – 107.9 MHz
(US, Canadian model)
50 kHz/200 kHz switchable
87.5 – 108.0 MHz (at 50 kHz step)
87.5 – 107.9 MHz (at 200 kHz step)
(E model)
Antenna terminal External antenna connector
Intermediate frequency 10.7 MHz
Usable sensitivity 8 dBf
Selectivity
Signal-to-noise ratio
75 dB at 400 kHz
65 dB (stereo),
68 dB (mono)
Harmonic distortion at 1 kHz
0.5% (stereo),
Separation
Frequency response
Capture ratio
0.3% (mono)
35 dB at 1 kHz
30 – 15,000 Hz
2 dB
SW (E model)
Tuning range SW tuning interval:
SW1: 2,940 – 7,735 kHz
SW2: 9,500 – 18,135 kHz
Antenna terminal
(except for 10,140 – 11,575 kHz)
External antenna connector
Intermediate frequency 10.71 MHz/450 kHz
Sensitivity 50 µV
– Continued on next page –
US, Canadian Model
FM/AM CASSETTE CAR STEREO
E Model
FM/MW/SW CASSETTE CAR STEREO
MICROFILM
Power amplifier section
Outputs Speaker outputs
(sure seal connectors)
Speaker impedance 4 – 8 ohms
Maximum power output 40 W
×
4 (at 4 ohms)
General
Outputs Power antenna control lead/Power amplifier control lead/Telephone
ATT control lead (E model only)
Rear line out (1)
Tone controls Bass ± 8 dB at 100 Hz
Treble ± 8 dB at 10 kHz
12 V DC car battery Power requirements
Dimensions
(negative ground)
Approx. 188
×
58
×
181 mm
(7
1
/
2
×
2
3
/
8
×
7
1
/
4
in.)
(w/h/d)
Mounting dimensions Approx. 182
×
53
×
164 mm
(7
1
/
4
×
2
1
/
8
×
6
1
/
2
in.)
(w/h/d)
Mass
Supplied accessories
Approx. 1.2 kg (2 lb. 10 oz.)
Parts for installation and connections (1 set)
Front panel case (1)
Design and specifications are subject to change without notice.
TABLE OF CONTENTS
1.
GENERAL
Location of Controls ....................................................... 3
Resetting the Unit ........................................................... 4
Detaching the Front Panel ............................................... 4
Setting the Clock ............................................................. 4
Installation ....................................................................... 5
Connection ...................................................................... 7
2.
DISASSEMBLY
......................................................... 9
3.
ASSEMBLY OF MECHANISM DECK
............ 11
4.
MECHANICAL ADJUSTMENTS
....................... 14
5.
ELECTRICAL ADJUSTMENTS
Test Mode ........................................................................ 14
Tape Deck Section .......................................................... 14
Tuner Section .................................................................. 15
6.
DIAGRAMS
6-1. IC Pin Function Description ........................................... 17
6-2. Printed Wiring Board –MAIN Section– ........................ 21
6-3. Schematic Diagram –MAIN Section– ........................... 23
6-4. Printed Wiring Board –PANEL Section– ...................... 27
6-5. Schematic Diagram –PANEL Section– ......................... 29
7.
EXPLODED VIEWS
................................................ 33
8.
ELECTRICAL PARTS LIST
............................... 36
– 2 –
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C during repairing.
• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or unsoldering.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
SECTION 1
GENERAL
This section is extracted from instruction manual.
– 3 –
– 4 –
– 5 –
– 6 –
– 7 –
– 8 –
SECTION 2
DISASSEMBLY
Note:
Follow the disassembly procedure in the numerical order given.
FRONT PANEL ASS’Y
A
1
Push the button
(release).
2
Remove the front panel ass’y to the direction of the arrow
A
.
COVER ASS’Y
2
1
2
1
3 cover ass’y
2
1
– 9 –
SUB PANEL, MACHANISM DECK (MG-25F-136)
3 connector
(CN351)
5 screw
(PTT2.6
×
6)
6 mechanism deck
(MG-25F-136)
4 flexible flat cable
(CN301)
2 sub panel
1 three screws
(PTT2.6
×
8)
1 three screws
(PTT2.6
×
8)
MAIN BOARD, HEAT SINK
5 two ground point screws
4 main board
– 10 –
5 three screws
(PTT2.6
×
8)
5 two screws
(PTT2.6
×
10)
1 screw
(PTT2.6
×
8)
5 two screws
(PTT2.6
×
8)
6 heat sink
2 rubber cap (25)
1 two screws
(PTT2.6
×
8)
SECTION 3
ASSEMBLY OF MECHANISM DECK
Note:
Follow the assembly procedure in the numerical order given.
5
Fit projection on
C
part.
HOUSING
7
Holder the hanger by bending the claw.
2
Install the hanger onto two claws of the housing.
1
Install the catch to the hanger.
4
Fit claw on
B
part.
hanger
3
Put the housing under
A
part.
6
Fit projection on
D
part.
housing
C
part
8
Hold the hanger by bending the claw.
D
part
A
part
B
part
ARM (SUCTION)
2
Move the arm (suction) in the arrow direction and fit on projection.
projection
1
Fit the arm (suction) on the shaft.
– 11 –
LEVER (LDG-A) / (LDG-B)
shaft
A shaft
B shaft
C
1
Fit the lever (LDG-A) on shafts
A
–
C
and install it.
shaft
A shaft
B
3 type-E stop ring 2.0
2
Fit the lever (LDG-B) on shafts
A
and
B
and install it.
GEAR (LDG-FT)
hole gear (LDG-D)
5 gear (LDG-FT) hole lever (LDG-A) gear (LDG-FB)
4
Align hole in the gear (LDG-D) with hole the lever (LDG-A).
6 polyethylene washer
1
2 tension spring (LD-2)
3
Move the lever (LDG-B) in the arrow direction.
2 tension spring (LD-1)
– 12 –
GUIDE (C)
2 guide (C)
1 three claws
– 13 –
SECTION 4
MECHANICAL ADJUSTMENTS
1. Clean the following parts with a denatured-alcohol-moistened swab: playback head pinch roller rubber belt idler capstan
2. Demagnetize the playback head with a head demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the parts adjusted.
5. The adjustments should be performed with the power supply voltage unless otherwise noted.
•
Torque Measurement
Mode Torque Meter
CQ-102C Forward
Forward
Back Tension
Reverse
Reverse
Back Tension
FF, REW
CQ-102C
CQ-102RC
CQ-102RC
CQ-201B
Meter Reading
30 – 65 g•cm
(0.42 – 0.90 oz·inch)
0.5 – 4.5 g•cm
(0.01 – 0.06 oz·inch)
30 – 65 g•cm
(0.42 – 0.90 oz·inch)
0.5 – 4.5 g•cm
(0.01 – 0.06 oz·inch)
60 – 200 g•cm
(0.83 – 2.78 oz·inch)
SECTION 5
ELECTRICAL ADJUSTMENTS
TEST MODE
This set have the test mode function. In the test mode, FM Auto
Scan/Stop Level and AM (MW) Auto Scan/Stop Level adjustments can be performed easier than it in ordinary procedure.
<Set the Test Mode>
1. Set the “power select” switch (S501) is “A (ON) ” position.
2. Turn ON the regulated power supply. (All LEDs on the set lights up, and the clock is displayed.)
Note:
Press the
[OFF] button, if the clock is not displayed.
3. Push the preset
[4]
button.
4. Push the preset
5. Press the preset
[5]
button.
[1]
button for more than two seconds.
6. Then the display indicates all lights, the test mode is set.
<Release the Test mode>
1. Push the
[OFF]
button.
2. Return the “power select” switch (S501) to initially set position.
•
Tape Tension Measurement
Mode Tension Meter
Forward CQ-403A
Reverse CQ-403R
Meter Reading more than 90 g
(more than 3.18 oz) more than 90 g
(more than 3.18 oz)
See the adjustment location from on page 16 for the adjustment.
0 dB=0.775 V
TAPE DECK SECTION
Tape Speed Adjustment
Setting:
test tape
WS-48A
(3 kHz, 0 dB) speed checker or frequency counter
4
Ω set speaker out terminal
– +
Procedure:
1. Put the set into the FWD PB mode.
2. Adjust adjustment resistor for inside capstan motor so that the reading on the speed checker or frequency counter becomes in specification.
Specification: Constant speed
Speed checker
–1.5 to +2.5%
Adjustment Location: See page 16.
Frequency counter
2,955 to 3,075 Hz
– 14 –
TUNER SECTION
(E model only)
US/Canadian model, a tuner section is no adjustment.
0 dB=1 µV
Cautions during repair
When the tuner unit is defective, replace it by a new one because its internal block is difficult to repair.
Note:
Adjust the tuner section in the sequence shown below.
1. FM Auto Scan/Stop Level Adjustment
2. FM Noise Focus Adjustment
3. FM Stereo Separation Adjustment
4. AM (MW) Auto Scan/Stop Level Adjustment
FM Auto Scan/Stop Level Adjustment
Setting:
[SOURCE]
button: FM
FREQUENCY SELECT switch: FM 200 k
FM RF signal generator antenna jack (J1)
0.01
µ
F set
Carrier frequency : 97.9 MHz
Output level : 22 dB (12.6
µ
V)
Mode : mono
Modulation : 1 kHz, 22.5 kHz deviation (30%)
Procedure:
1. Set to the test mode. (See page 14.)
2. Push the
[SOURCE]
button and set to FM.
Display
SHUF1
FM
97.9
3. Adjust with the volume RV2 on TU1 so that the “FM” indication turns to “FMI” indication on the display window.
But, in case of already indicated “FMI”, turn the RV2 so that put out light “I” indication and adjustment.
Display
SHUF1
97.9
Adjustment Location: See page 16.
FM Noise Focus Adjustment
Setting:
[SOURCE]
button: FM
FREQUENCY SELECT switch: FM 200 k
FM RF signal generator antenna jack (J1)
0.01
µ
F set
4
Ω level meter
+
– speaker out terminal
Carrier frequency : 97.9 MHz
Output level : 60 dB (1 mV)
Mode
Modulation
: stereo
: 1 kHz, 75 kHz deviation (100%)
Procedure:
1. Tune the 97.9 MHz.
2. The then output level is supposing that (A) dB.
3. Adjust with the volume RV3 on TU1 so that the output level is
(A) –32 ± 2 dB then signal generator input set to –20 dB.
Adjustment Location: See page 16.
FM Stereo Separation Adjustment
Setting:
[SOURCE]
button: FM
FREQUENCY SELECT switch: FM 200 k
FM RF signal generator antenna jack (J1)
0.01
µ
F
4
Ω set level meter
+
–
Carrier frequency : 97.9 MHz
Output level : 70 dB (3.2 mV) speaker out terminal
Mode
Modulation
: stereo
: main: 1 kHz, 33.75 kHz deviation (45%)
sub: 1 kHz, 33.75 kHz deviation (45%)
19 kHz pilot: 7.5 kHz deviation (10%)
Procedure:
FM Stereo signal generator output channel
L-CH
R-CH
R-CH
L-CH
Level meter connection
L-CH
L-CH
R-CH
R-CH
Level meter reading (dB)
A
B
Adjust RV4 on TU1 for minimum reading.
C
D
Adjust RV4 on TU1 for minimum reading.
L-CH Stereo separation: A-B
R-CH Stereo separation: C-D
The separations of both channels should be equal.
Specification: Separation more than 28 dB
Adjustment Location: See page 16.
– 15 –
AM (MW) Auto Scan/Stop Level Adjustment
Make this adjustment after “FM Auto Scan/Stop Level Adjustment”.
Setting:
[SOURCE]
and
[MODE]
button: MW
FREQUENCY SELECT switch: MW 10 k
Adjustment Location:
– SET UPPER VIEW –
Tape Speed Adjustment
30
Ω
15 pF
65 pF
AM RF signal generator
AM dummy antenna
(50
Ω
) set
Carrier frequency : 1000 kHz
30% amplitude modulation by
1 kHz signal
Output level : 33 dB (44.7
µ
V) antenna jack (J1)
Procedure:
1. Set to the test mode. (See page 14.)
2. Push the
[SOURCE]
button and set to FM.
3. Push the
[MODE]
button and set to MW.
Display
INTRO
SHUF1
MW
1000
4. Adjust with the volume RV1 on TU1 so that the “MW” indication turns to “MWI” indication on the display window.
But, in case of already indicated “MWI”, turn the RV1 so that put out light “I” indication and adjustment.
Display
INTRO
SHUF1
1000
TU 1
RV 4 FM Stereo Separation Adjustment
RV 3 FM Noise Focus Adjustment
RV 2 FM Auto Scan/Stop Level Adjustment
RV 1 AM (MW) Auto Scan/Stop Level Adjustment
– 16 –
SECTION 6
DIAGRAMS
6-1.
IC PIN FUNCTION DESCRIPTION
•
MAIN BOARD IC501
µ
PD17708GC-567-3B9 (SYSTEM CONTROLLER)
Pin No.
1
2
3
4
5
6
7
8
9
22
23
24
25
34
35
36
31
32
33
37
38
26
27
28
29
30
17
18
19
14
15
16
20
21
10
11
12
13
Pin Name
AMSSEL
POS3
POS2
POS0
POS1
TAPEON
CM ON
LM LOD
LM EJ
RC IN0
VSM
AMIFIN
FMIFIN
VDD2
FM OSC
AM OSC
GND
NCO
EO1
TEST0
NCO
SEKOUT
TUNON
FM ON
PW ON
MUT
VOLCE
VOLCKO
VOLSO
AMPON
AMPMUT
DX/LO
AM MONO
GND
DSTSEL
DBASIN
KEYIN1
KEYIN0
I/O
I
I
I
I
I
O
O
Function
Setting terminal for the AMS selection fixed at “L”
Tape position detect input from tape operation switch on the mechanism block
O
I
Tape system power supply on/off control signal output terminal “H”: tape on
Capstan/reel motor (M901) drive signal output terminal “H”: motor on
Loading/tape operation motor control signal output to the LB1638M (IC351)
(For the loading direction and forward side operation) *1
O
Loading/tape operation motor control signal output to the LB1638M (IC351)
(For the eject direction and reverse side operation) *1
Tuner system power supply on/off control signal output to the BA3918 (IC611) “H”: tuner on O
O
O
O
O
O
O
O
O
O
FM system power supply on/off control signal output to the BA3918 (IC611) “H”: FM on
Main system power supply on/off control signal output to the BA3918 (IC611) “H”: power on
Line muting control signal output terminal “H”: line muting on
Chip enable signal output to the electrical volume (IC331)
Serial data transfer clock signal output to the electrical volume (IC331)
Serial data output to the electrical volume (IC331)
Standby control signal output to the power amplifier (IC751) “L”: standby
Muting control signal output to the power amplifier (IC751) “L”: muting on
Local/DX selection signal output to the FM/AM tuner unit (TU1) “L”: DX, “H”: local
O AM forced monaural signal output terminal Not used (open)
— Ground terminal
Destination setting terminal
US, Canadian models: fixed at center voltage
E model: frequency select switch (S502) input
“L”: AM 9k step or FM 50k step, “H”: AM 10k step or FM 200k step
I
I
D-BASS switch (SW951) input (A/D input)
Key input terminal (A/D input)
6, INTRO 1, REPEAT 2, SHUF 3, BL SKIP 6, ATA 5, 4, PRESET DISC +/– keys input
(LSW921 to LSW927, LSW929 and LSW930)
I
I
I
Key input terminal (A/D input)
OFF, SOURCE, MODE
*, + ) + SEEK AMS, – = 0 SEEK AMS, VOLUME –,
SEL, VOLUME +, ATT , DSPL, BTM, LCL keys input (LSW901 to LSW912)
Rotary remote commander shift key A/D input terminal
FM and AM signal meter voltage detection input from the FM/AM tuner unit (TU1)
I
I
AM intermediate frequency detection signal input from the FM/AM tuner unit (TU1)
FM intermediate frequency detection signal input from the FM/AM tuner unit (TU1)
— Power supply terminal (+5V)
O
O
I
I
I
FM local oscillator detection signal input from the FM/AM tuner unit (TU1)
AM local oscillator detection signal input from the FM/AM tuner unit (TU1)
— Ground terminal
O
O
Not used (open)
Main charge-pump control signal output terminal
Setting terminal for the test (fixed at “L”)
Not used (open)
Seek control signal output to the FM/AM tuner unit (TU1)
– 17 –
59
60
61
62
63
64
65
51
52
53
54
55
56
57
58
Pin No.
39
40
41
42
43
44
45
46
47
48
49
50
Pin Name
MW/SW
BEEP
KEYACK
BU IN
MTLSEL
DOLON
AMSIN
ST
AMS ON
N/R OUT
TAPMUT
ILLON
SD IN
NOSESW
TELMUT
REL T
ACCIN
TESTIN
RC IN1
PW SEL
MTLIN
ADON
KEYSEL
SEKOUTSEL
COLORSEL
LCDCE
LCDCKO
I/O
O
Function
MW/SW selection signal output to the FM/AM tuner unit (TU1) “L”: MW, “H”: SW
Used for the E mode
O Beep sound output terminal
I
I
Input of acknowledge signal for the key entry Acknowledge signal is input to accept function and eject keys in the power off status On at input of “L”
Battery detect signal input terminal “H”: battery on
I/O
METAL control in/out terminal
At initial mode: auto/manual mode selection input of METAL function “L”: manual mode
At manual mode: METAL on/off control signal output terminal (“H” output: METAL on)
At auto mode: input at MTLIN (pin %ª)
Not used this function in this set (fixed at “H”)
I/O
I
I/O
Dolby control in/out terminal
At initial mode: valid/invalid selection input of dolby function (“L” input: valid)
At normal mode: dolby on/off control signal output (“H” output : dolby on)
Not used this function in this set (fixed at “H”)
Whether a music is present or not from CXA2509AQ (IC301) is detected at auto music sensor
“L”: music is present, “H”: music is not present
Input of FM stereo detection signal from FM/AM tuner unit (TU1), and output of forced monaural control signal to FM/AM tuner unit (TU1) (Commonly used for stereo display input and forced monaural output)
FM stereo detection at input of “L”, forced monaural at output of “L”
O
O
Tape auto music sensor control signal output to the CXA2509AQ (IC301)
“L” is output to lower the gain for audio level at FF/REW
Forward/reverse direction control signal output to the CXA2509AQ (IC301)
“L: forward direction, “H”: reverse direction
O Tape muting on/off control signal output to the CXA2509AQ (IC301) “H”: tape muting on
O
Power supply on/off control signal output terminal at the illumination and liquid crystal display driver (IC901) “H”: power on
At power select switch (S501) on mode: “H” output at the accessory on
At power select switch (S501) off mode: “H” output at the power on
I
I
I
I
I
I
I
I
Station detector detect input from the FM/AM tuner unit (TU1)
Stop level for SEEK, BTM, etc. is determined SD is present at input of “H”
Detects the removal of the attaching and removing type front panel block “L”: attaching
Telephone muting signal input terminal At input of “L”, the signal is attenuated by –20 dB
Used for the E model
Reel table rotation detect signal input from the take-up and supply reel sensor
Accessory detect signal input terminal “L”: accessory on
Setting terminal for the test mode “L”: test mode (normally fixed at “H”)
Rotary remote commander shift key A/D input terminal
Power select switch (S501) input terminal
“L”: position A (halt mode), “H”: position B (operation mode)
I
I
Input terminal to set whether the auto metal function is present or not
“L”: auto metal function is present (fixed at “H”)
O Power supply on/off control signal output for the A/D conversion
I Setting terminal for the key (fixed at “H”)
Active selection terminal for the SEKOUT (pin #•)
(US, Canadian models: fixed at “H”, E model: fixed at “L”)
I Setting terminal for the illumination color “L”: amber, “H”: green (fixed at “H”)
O Chip enable output to the liquid crystal display driver (IC901)
O Serial data transfer clock signal output to the liquid crystal display driver (IC901)
– 18 –
Pin No.
66
67
76
77
78
79
73
74
75
68
69
70
71
72
80
Pin Name
LCDSO
LCDINH
UNICKI
UNISO
UNISI
UNICKO
BUSON
SYSRST
VREG
GND
X OUT
X IN
CE
VDD1
RESET
I/O Function
O Serial data output to the liquid crystal display driver (IC901)
O
Blank indicate control signal output to the liquid crystal display driver (IC901)
“L”: no display
I Serial data reading clock signal input terminal (for SONY bus)
O Serial data output to the bus interface (IC581) (for SONY bus)
I Serial data input from the bus interface (IC581) (for SONY bus)
O Serial data transfer clock signal output to the bus interface (IC581) (for SONY bus)
O Bus on/off control signal output to the bus interface (IC581) (for SONY bus) “L”: bus on
O Reset signal output to the bus interface (IC581) (for SONY bus) “L”: reset
O CPU regulator output terminal Connected to capacitor
— Ground terminal
O Main system clock output terminal (4.5 MHz)
I Main system clock input terminal (4.5 MHz)
I CPU chip enable signal input (fixed at “H”)
— Power supply terminal (+5V)
I
System reset signal input from the reset signal generator (IC551) and reset switch (S551)
“L” is input for several 100 msec after power on, then it changes to “H”
*1 loading/tape operation motor control
MODE
STOP
TERMINAL
LM LOD (pin 8)
LM EJ (pin 9)
“L”
“L”
LOADING/
FORWARD
“H”
“L”
EJECT/
REVERSE
“L”
“H”
BRAKE
“H”
“H”
– 19 –
• IC Block Diagrams – MAIN Board –
IC301 CXA2509AQ-T4
PBFB1
PBRIN1
31
32
PBREF1
33
PBFIN1
34
VCT
PBGND
35
36
PBFIN2 37
PBREF2 38
PBRIN2
PBFB2
39
40
30
VCT
29 28 27 26
120
µ
/70
µ
T2
– +
F2
F1
X1
+
X1
25
NR BIAS
TAPE/AUX
TAPE EQ
LPF
FWD/RVS
VCC
+
–
F3
24 23 22 21
24dB
+ –
MS
MODE
20
19
18
17
16
MSMODE
DRSW
TAPESW
INSW
NC
MS ON/
OFF
DETECT
15 NC
14 MSOUT
13 DGND
12 MSTC
11 G1FB
1
– +
120
µ
/70
µ
2 3 4 5
T1
+
–
6
OFF/B
7
24dB
8 9 10
IC331 LC75373ED
LSELO
L4
L3
L2
L1
34
35
36
37
38
VDD 39
R1
R2
R3
R4
RSELO
40
41
42
43
44
33
1
+
–
–
+
+
–
–
+
32
2
–
+
+
–
31 30 29 28 27 26 25 24 23
+
+
–
–
3 4 5
–
+
+
–
–
+
+
–
+
–
22 LFIN
21 LFOUT
20
LROUT
–
+
DECODER
+
–
LATCH
SHIFT
REGISTER
CONTROL
–
+
–
+
+
–
19 VREF
18
17
16
15
14
CE
DI
CL
VSS
RROUT
13
12
RFOUT
RFIN
6 7 8 9 10 11
– 31 –
– 32 –
NOTE:
• -XX and -X mean standardized parts, so they may have some difference from the original one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑ ↑
Parts Color Cabinet's Color
(1) CHASSIS SECTION
8
SECTION 7
EXPLODED VIEWS
• Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Hardware (# mark) list and accessories and packing materials are given in the last of the electrical parts list.
14
15
MG-25F-136
#3
F781
9
6
7
10
#2
#4
11
#2
#2
4
5
3
2
12
#2
13
#1
#2
#2
1
Front panel ass’y
* 5
* 6
* 6
7
* 8
Ref. No.
Part No.
3
3
1
2
4
Description
3-018-383-01 PANEL, SUB
3-935-003-01 SPRING, TORSION
3-932-205-41 DOOR, CASSETTE (E)
3-932-205-61 DOOR, CASSETTE (US,Canadian)
X-3367-636-1 LOCK ASSY
Remark
3-010-377-01 INSULATOR
A-3313-439-A MAIN BOARD, COMPLETE (E)
A-3313-440-A MAIN BOARD, COMPLETE (US,Canadian)
3-915-923-01 SCREW, GROUND POINT
X-3373-270-1 COVER ASSY
Ref. No.
Part No.
9
9
* 10
* 11
12
Description
1-776-207-31 CORD (WITH CONNECTOR) (POWER)
Remark
1-776-207-81 CORD (WITH CONNECTOR) (POWER) (E)
3-018-390-01 BRACKET (IC)
3-018-389-01 HEAT SINK
3-935-014-01 CUSHION (U)
(US, Canadian)
* 13
14
15
F781
3-009-813-01 CHASSIS
3-012-859-01 CAP (25), RUBBER
3-937-650-01 PLATE (C), GROUND
1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) (10A)
– 33 –
(2) FRONT PANEL SECTION
102
not supplied
(KEY board)
#5
#5
119
105
107
108
109
120
111
104
103
101
114
121
112
113
115
106
116
LCD901
117
118
Ref. No.
Part No.
101
102
103
104
105
Description
3-018-799-01 BUTTON (D-BASS)
3-015-036-01 CUSHION (BACK PANEL)
3-016-932-01 BUTTON (L) (2) (+. -)
3-017-103-01 BUTTON (RELEASE)
3-932-475-01 SPRING (RELEASE)
* 106
107
108
109
111
112
3-019-149-01 PLATE, LCD
X-3374-687-1 PANEL SUB ASSY
3-016-938-01 BUTTON (SOURCE)
3-018-658-01 BUTTON (L) (+ + ). SEEK AMS.
= 0 -. r. OFF. r. SEL. ATT)
3-016-933-01 BUTTON (1-3) (
6. 1. 2. 3)
118 3-009-295-01 PANEL, FRONT BACK
119
* 120
* 121
3-904-194-01 EMBLEM (NO. 2.5), SONY
3-024-391-01 SHEET (LCD)
3-024-846-01 SHEET (LCD) B
LCD901 1-801-967-51 DISPLAY PANEL, LIQUID CRYSTAL
3-016-931-11 BUTTON (4-6) (4. 5. 6)
Remark Ref. No.
Part No.
113
* 114
* 115
* 116
* 117
Description
3-016-936-01 BUTTON (R) (B) (BTM. LCL. -. DISC. +)
3-019-151-01 PLATE (LCD), GROUND
3-019-150-01 SHEET (REFLECTOR)
3-018-612-01 PLATE, LIGHT GUIDE
3-018-611-01 HOLDER (LCD)
Remark
– 34 –
(3) MECHANISM DECK SECTION
(MG-25F-136)
159
153
154
155
#6
158
157
156
A
152
160
A
161
162
164
168
168
#7
165
166
167
163
HP901
M901
151
Ref. No.
Part No.
151
* 152
* 153
154
155
Description
A-3291-667-A CLUTCH (FR) ASSY
3-019-130-01 LEVER (LDG-A)
3-019-131-01 LEVER (LDG-B)
3-020-539-01 SPRING (LD-1), TENSION
3-020-540-01 SPRING (LD-2), TENSION
156
157
158
* 159
160
3-020-542-01 GEAR (LOADING FT)
3-341-753-11 WASHER, POLYETHYLENE
3-020-533-01 HOUSING
3-020-532-01 ARM (SUCTION)
3-020-534-01 HANGER
Remark Ref. No.
Part No.
161
162
163
164
165
Description
3-933-346-01 CATCHER
3-933-344-01 GUIDE (C)
3-014-798-01 SCREW (HEAD), SPECIAL
3-364-151-01 WASHER
A-3301-267-A CHASSIS ASSY (G)
166
167
168
3-017-302-01 BELT (25)
3-936-853-01 FLYWHEEL (F)
3-701-437-21 WASHER
HP901 1-500-157-21 HEAD, MAGNETIC (PLAYBACK)
M901 A-3291-665-A MOTOR ASSY, MAIN (CAPSTN/REEL)
Remark
– 35 –
KEY
NOTE:
• Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set.
• -XX and -X mean standardized parts, so they may have some difference from the original one.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
SECTION 8
ELECTRICAL PARTS LIST
• Items marked “*” are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• SEMICONDUCTORS
In each case, u: µ, for example: uA. .
: µA. .
uPA. . : µPA. .
uPB. .
: µPB. .
uPC. . : µPC. .
uPD. .
: µPD. .
• CAPACITORS uF: µF
• COILS uH: µH
When indicating parts by reference number, please include the board.
*
*
*
*
*
Ref. No.
Part No.
Description
KEY BOARD
**********
3-018-611-01 HOLDER (LCD)
3-018-612-01 PLATE, LIGHT GUIDE
3-019-149-01 PLATE, LCD
3-019-150-01 SHEET (REFLECTOR)
3-019-151-01 PLATE (LCD), GROUND
< CAPACITOR >
C901 1-163-033-00 CERAMIC CHIP 0.022uF
C902 1-165-319-11 CERAMIC CHIP 0.1uF
C903 1-165-319-11 CERAMIC CHIP 0.1uF
C904 1-163-137-00 CERAMIC CHIP 680PF 5%
< CONNECTOR >
CNP901 1-764-423-11 PIN, CONNECTOR 12P
< DIODE >
D901 8-719-420-90 DIODE MA8051-M
D902 8-719-422-64 DIODE MA8062-M
D903 8-719-422-64 DIODE MA8062-M
D904 8-719-422-64 DIODE MA8062-M
D905 8-719-422-64 DIODE MA8062-M
< IC >
IC901 8-759-443-68 IC LC75834JED
Remark
50V
50V
50V
50V
< CHIP CONDUCTOR >
JC901 1-216-295-00 SHORT 0
JC902 1-216-295-00 SHORT 0
JC951 1-216-296-00 SHORT 0
JC952 1-216-296-00 SHORT 0
< LIQUID CRYSTAL DISPLAY >
LCD901 1-801-967-51 DISPLAY PANEL, LIQUID CRYSTAL
< SWITCH >
LSW901 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (OFF)
LSW902 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (SOURCE)
LSW903 1-762-619-11 SWITCH, KEY BOARD (WITH LED)
(MODE *)
Ref. No.
Part No.
Description Remark
LSW904 1-762-619-11 SWITCH, KEY BOARD (WITH LED)
LSW905 1-762-619-11 SWITCH, KEY BOARD (WITH LED)
(+ + ))
( = 0 -)
LSW906 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (-)
LSW907 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (SEL)
LSW908 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (+)
LSW909 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (ATT)
LSW910 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (DSPL)
LSW911 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (BTM)
LSW912 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (LCL)
LSW921 1-762-619-11 SWITCH, KEY BOARD (WITH LED) ( 6)
LSW922 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (1/INTRO)
LSW923 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (2/REPEAT)
LSW924 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (3/SHUF)
LSW925 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (6/BL SKIP)
LSW926 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (5/ATA)
LSW927 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (4)
LSW929 1-762-619-11 SWITCH, KEY BOARD (WITH LED)
(DISC/PRESET +)
LSW930 1-762-619-11 SWITCH, KEY BOARD (WITH LED)
(DISC/PRESET -)
< PILOT LAMP >
PL901 1-517-633-21 LAMP, PILOT (LCD BACK LIGHT)
PL902 1-517-633-21 LAMP, PILOT (LCD BACK LIGHT)
< RESISTOR >
R901 1-216-647-11 METAL CHIP
R902 1-216-647-11 METAL CHIP
R903 1-216-647-11 METAL CHIP
R904 1-216-651-11 METAL CHIP
R905 1-216-655-11 METAL CHIP
R906 1-216-655-11 METAL CHIP
R907 1-216-659-11 METAL CHIP
R908 1-216-663-11 METAL CHIP
R909 1-216-667-11 METAL CHIP
R910 1-216-671-11 METAL CHIP
R911 1-208-806-11 RES, CHIP
R921 1-216-647-11 METAL CHIP
R922 1-216-647-11 METAL CHIP
R923 1-216-647-11 METAL CHIP
680
680
680
1K
1.5K
1.5K
2.2K
3.3K
4.7K
6.8K
10K
680
680
680
0.5%
0.5%
0.5%
0.5%
0.5%
2%
0.5%
0.5%
0.5%
1/10W
1/10W
1/10W
1/10W
1/10W
0.5% 1/10W
0.5% 1/10W
0.5% 1/10W
0.5% 1/10W
0.5% 1/10W
1/10W
1/10W
1/10W
1/10W
– 36 –
KEY MAIN
C17
C18
C19
C22
C23
C11
C12
C13
C14
C16
C25
C6
C7
C8
C9
C10
C1
C2
C3
C4
C5
*
*
Ref. No.
Part No.
R924
Description
1-216-651-11 METAL CHIP
R925 1-216-655-11 METAL CHIP
R926 1-216-655-11 METAL CHIP
R927 1-216-659-11 METAL CHIP
R928 1-216-663-11 METAL CHIP
R929 1-216-667-11 METAL CHIP
R951
R952
R953
R954
R955
R956
R961
R962
R963
R964
1-216-190-00 RES, CHIP
1-216-089-00 RES, CHIP
1-216-049-11 RES, CHIP
1-216-049-11 RES, CHIP
1-216-049-11 RES, CHIP
1-216-049-11 RES, CHIP
1-216-027-00 METAL CHIP
1-216-025-00 RES, CHIP
1-216-033-00 METAL CHIP
1-216-035-00 METAL CHIP
R965 1-216-035-00 METAL CHIP
R966 1-216-025-00 RES, CHIP
R981 1-216-655-11 METAL CHIP
R982 1-216-663-11 METAL CHIP
R983 1-216-671-11 METAL CHIP
1K
1.5K
1.5K
2.2K
3.3K
4.7K
470
47K
1K
1K
1K
1K
120
100
220
270
270
100
1.5K
3.3K
6.8K
22K
0.5%
Remark
1/10W
0.5% 1/10W
0.5% 1/10W
0.5% 1/10W
0.5% 1/10W
0.5% 1/10W
5%
5%
5%
5%
5%
1/8W
1/10W
1/10W
1/10W
1/10W
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
5%
5%
1/10W
1/10W
0.5% 1/10W
0.5% 1/10W
0.5% 1/10W
5% 1/10W R984 1-216-081-00 METAL CHIP
< SWITCH >
*
*
SW951 1-762-937-11 SWITCH, ROTARY (D-BASS)
************************************************************
A-3313-439-A MAIN BOARD, COMPLETE (E)
A-3313-440-A MAIN BOARD, COMPLETE (US, Canadian)
*********************
3-018-389-01 HEAT SINK
3-018-390-01 BRACKET (IC)
7-685-793-09 SCREW +PTT 2.6X8 (S)
7-685-794-09 SCREW +PTT 2.6X10 (S)
< CAPACITOR >
Ref. No.
Part No.
Description
C26
C27
1-163-017-00 CERAMIC CHIP 0.0047uF 5%
1-164-222-11 CERAMIC CHIP 0.22uF
C101 1-163-263-11 CERAMIC CHIP 330PF
C102 1-163-263-11 CERAMIC CHIP 330PF
5%
5%
C104 1-164-232-11 CERAMIC CHIP 0.01uF
C105 1-164-489-11 CERAMIC CHIP 0.22uF
10% 16V
C106 1-163-227-11 CERAMIC CHIP 10PF
C107 1-163-227-11 CERAMIC CHIP 10PF
C108 1-126-163-11 ELECT 4.7uF
0.5PF
0.5PF
20%
50V
50V
50V
50V
C109 1-163-251-11 CERAMIC CHIP 100PF
C110 1-163-133-00 CERAMIC CHIP 470PF
5%
5%
50V
50V
C121 1-163-809-11 CERAMIC CHIP 0.047uF
10% 25V (E)
C121 1-164-004-11 CERAMIC CHIP 0.1uF
10% 25V
(US, Canadian)
C122 1-163-037-11 CERAMIC CHIP 0.022uF
10% 25V
(US, Canadian)
C122 1-164-492-11 CERAMIC CHIP 0.15uF
10% 16V (E)
C123 1-164-004-11 CERAMIC CHIP 0.1uF
C124 1-164-004-11 CERAMIC CHIP 0.1uF
C141 1-126-157-11 ELECT
C142
C151 1-163-037-11 CERAMIC CHIP 0.022uF
10% 25V (E)
C151 1-163-989-11 CERAMIC CHIP 0.033uF
10% 25V
C152 1-124-257-00 ELECT
C161 1-126-160-11 ELECT
C162
C163
C164
C165
C166
1-163-251-11 CERAMIC CHIP
1-109-982-11 CERAMIC CHIP
1-164-182-11 CERAMIC CHIP
1-163-037-11 CERAMIC CHIP
1-126-157-11 ELECT
1-164-492-11 CERAMIC CHIP
10uF
100PF
2.2uF
1uF
1uF
10%
10%
20%
5%
(US, Canadian)
20% 50V
20%
10% 10V
0.0033uF 10%
0.022uF
10uF
0.15uF
10%
20%
10%
Remark
50V
25V
50V
50V
25V
25V
16V
50V
50V
50V
25V
16V
16V
C167 1-164-492-11 CERAMIC CHIP 0.15uF
10% 16V
C168 1-126-157-11 ELECT 10uF
C169 1-163-227-11 CERAMIC CHIP 10PF
C170 1-163-157-00 CERAMIC CHIP 10PF
C171 1-126-163-11 ELECT 4.7uF
C172 1-163-133-00 CERAMIC CHIP 470PF
20%
0.5PF
5%
20%
5%
16V
50V
50V
50V
50V
1-163-235-11 CERAMIC CHIP 22PF 5% 50V
1-163-009-11 CERAMIC CHIP 0.001uF
10% 50V
1-124-584-00 ELECT
1-126-157-11 ELECT
1-124-584-00 ELECT
100uF
10uF
100uF
20%
20%
20%
10V
16V
10V
1-164-232-11 CERAMIC CHIP 0.01uF
1-164-232-11 CERAMIC CHIP 0.01uF
50V
50V
1-164-232-11 CERAMIC CHIP 0.01uF
1-163-251-11 CERAMIC CHIP 100PF 5%
50V
50V
1-163-009-11 CERAMIC CHIP 0.001uF
10% 50V
1-126-160-11 ELECT 1uF 20% 50V
1-163-009-11 CERAMIC CHIP 0.001uF
10% 50V
1-163-251-11 CERAMIC CHIP 100PF
1-164-232-11 CERAMIC CHIP 0.01uF
5% 50V
50V
1-164-232-11 CERAMIC CHIP 0.01uF
50V
1-163-009-11 CERAMIC CHIP 0.001uF
10% 50V
1-163-059-00 CERAMIC CHIP 0.01uF
10% 50V
1-164-222-11 CERAMIC CHIP 0.22uF
1-124-584-00 ELECT 100uF
1-124-234-00 ELECT 22uF
20%
20%
25V
10V
16V
1-164-489-11 CERAMIC CHIP 0.22uF
10% 16V
C174 1-164-489-11 CERAMIC CHIP 0.22uF
10% 16V
C181 1-126-163-11 ELECT 4.7uF
C182 1-163-133-00 CERAMIC CHIP 470PF
C183 1-163-251-11 CERAMIC CHIP 100PF
20%
5%
5%
50V
50V
50V
C184 1-164-489-11 CERAMIC CHIP 0.22uF
10% 16V
C191 1-163-251-11 CERAMIC CHIP 100PF
C201 1-163-263-11 CERAMIC CHIP 330PF
C202 1-163-263-11 CERAMIC CHIP 330PF
C204 1-164-232-11 CERAMIC CHIP 0.01uF
5%
5%
5%
50V
50V
50V
50V
C205 1-164-489-11 CERAMIC CHIP 0.22uF
10% 16V
C206 1-163-227-11 CERAMIC CHIP 10PF
C207 1-163-227-11 CERAMIC CHIP 10PF
C208 1-126-163-11 ELECT 4.7uF
C209 1-163-251-11 CERAMIC CHIP 100PF
C210 1-163-197-00 CERAMIC CHIP 470PF
0.5PF
50V
0.5PF
50V
20% 50V
5% 50V
5% 50V
C241 1-126-157-11 ELECT 10uF
C242 1-163-251-11 CERAMIC CHIP 100PF
20% 16V
5% 50V
C251 1-163-037-11 CERAMIC CHIP 0.022uF
10% 25V (E)
C251 1-163-989-11 CERAMIC CHIP 0.033uF
10% 25V
C252 1-124-257-00 ELECT 2.2uF
(US, Canadian)
20% 50V
– 37 –
MAIN
Ref. No.
C261 1-126-160-11 ELECT 1uF
C262 1-109-982-11 CERAMIC CHIP 1uF
C263 1-164-182-11 CERAMIC CHIP 0.0033uF 10% 50V
C264 1-163-037-11 CERAMIC CHIP 0.022uF
10% 25V
C265 1-126-157-11 ELECT
C266
C267
C268 1-126-157-11 ELECT 10uF
C269 1-163-227-11 CERAMIC CHIP 10PF
C270 1-163-227-11 CERAMIC CHIP 10PF
C271
C272
Part No.
Description
1-164-492-11 CERAMIC CHIP
1-164-492-11 CERAMIC CHIP
1-126-163-11 ELECT
1-163-133-00 CERAMIC CHIP
10uF
0.15uF
0.15uF
4.7uF
470PF
20%
10%
20% 16V
10%
10%
20%
0.5PF
0.5PF
20%
5%
Remark
Ref. No.
Part No.
50V
10V
16V
16V
16V
50V
50V
50V
50V
C274 1-164-489-11 CERAMIC CHIP 0.22uF
10% 16V
C281 1-126-163-11 ELECT 4.7uF
20% 50V
C282 1-163-133-00 CERAMIC CHIP 470PF 5% 50V
C751 1-126-096-11 ELECT 10uF
C752 1-107-682-11 CERAMIC CHIP 1uF
C754
C755
C781 1-126-936-11 ELECT 3300uF 20% 16V
C782 1-163-077-00 CERAMIC CHIP 0.1uF
10% 25V
C783 1-163-077-00 CERAMIC CHIP 0.1uF
C785
C786
Description
1-124-257-00 ELECT
1-124-589-11 ELECT
1-165-319-11 CERAMIC CHIP
1-165-319-11 CERAMIC CHIP
2.2uF
47uF
0.1uF
0.1uF
C791 1-109-982-11 CERAMIC CHIP 1uF
C901 1-163-251-11 CERAMIC CHIP 100PF
20%
10%
20% 50V
20% 16V
10% 25V
10%
5%
Remark
35V
16V
50V
50V
10V
50V
C906 1-163-009-11 CERAMIC CHIP 0.001uF
10% 50V (E)
C283 1-163-251-11 CERAMIC CHIP 100PF
C284 1-164-489-11 CERAMIC CHIP 0.22uF
10% 16V
C301 1-124-234-00 ELECT
C302 1-131-359-41 ELECT
22uF
10uF
C303 1-163-251-11 CERAMIC CHIP 100PF
5%
20%
10%
5%
50V
16V
25V
50V
C906 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
(US, Canadian)
C907 1-163-009-11 CERAMIC CHIP 0.001uF
10% 50V (E)
C907 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C908
C909
1-163-251-11 CERAMIC CHIP
1-163-181-00 CERAMIC CHIP
100PF
100PF
5%
(US, Canadian)
50V
5% 50V
C304
C305
C306
1-164-004-11 CERAMIC CHIP
1-107-823-11 CERAMIC CHIP
1-164-232-11 CERAMIC CHIP
C331 1-124-584-00 ELECT
C332 1-124-234-00 ELECT
0.1uF
0.47uF
0.01uF
100uF
22uF
10%
10%
20%
20%
25V
16V
50V
10V
16V
C910 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C912 1-164-182-11 CERAMIC CHIP 0.0033uF 10% 50V
C913 1-164-004-11 CERAMIC CHIP 0.1uF
C914 1-164-004-11 CERAMIC CHIP 0.1uF
10%
10%
25V
25V
< CONNECTOR >
C353 1-164-004-11 CERAMIC CHIP 0.1uF
C354 1-126-157-11 ELECT
C355 1-126-157-11 ELECT
C356 1-126-934-11 ELECT
10uF
10uF
220uF
C357 1-163-251-11 CERAMIC CHIP 100PF
10% 25V
20% 16V
20% 16V
20% 16V
5% 50V
C359 1-164-489-11 CERAMIC CHIP 0.22uF
10% 16V
C501 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C502 1-163-234-11 CERAMIC CHIP 20PF
C503 1-124-584-00 ELECT 100uF
C504 1-164-004-11 CERAMIC CHIP 0.1uF
5%
20%
10%
50V
10V
25V
CN301 1-766-260-11 CONNECTOR, FFC/FPC (ZIF) 7P
* CN351
1-506-995-11 PIN, CONNECTOR (PC BOARD) 13P
CN581 1-580-907-31 PLUG, CONNECTOR (BUS CONTROL IN)
CN701 1-764-422-11 PLUG, CONNECTOR 12P
CN781 1-774-701-11 PIN, CONNECTOR 16P
CP1
< CONPOSITION CIRCUIT BLOCK >
1-519-504-11 GAP, DISCHARGE
C505
C551
C552
C553
C554
C571 1-126-163-11 ELECT 4.7uF
C581 1-162-638-11 CERAMIC CHIP 1uF
20% 50V
16V
C582 1-163-009-11 CERAMIC CHIP 0.001uF
10% 50V
C583 1-163-077-00 CERAMIC CHIP 0.1uF
10% 25V
C602 1-164-222-11 CERAMIC CHIP 0.22uF
25V
C611
C612
C613
C614
C615
C616 1-126-157-11 ELECT
C617 1-126-157-11 ELECT
10uF
10uF
C621 1-126-157-11 ELECT 10uF
C622 1-163-133-00 CERAMIC CHIP 470PF
C623 1-124-589-11 ELECT 47uF
C701
C702
C703
1-163-077-00 CERAMIC CHIP
1-125-701-11 DOUBLE LAYER
1-124-584-00 ELECT
1-164-004-11 CERAMIC CHIP
1-164-004-11 CERAMIC CHIP
1-126-157-11 ELECT
1-126-157-11 ELECT
1-163-077-00 CERAMIC CHIP
1-126-157-11 ELECT
1-126-157-11 ELECT
1-163-077-00 CERAMIC CHIP
1-163-077-00 CERAMIC CHIP
1-163-077-00 CERAMIC CHIP
0.1uF
0.047F
100uF
0.1uF
0.1uF
10uF
10uF
0.1uF
10uF
10uF
0.1uF
0.1uF
0.1uF
10% 25V
20% 10V
10% 25V
10%
20%
20%
10%
20%
20%
5.5V
25V
16V
16V
25V
16V
16V
20% 16V
20% 16V
20% 16V
5%
20%
10%
10%
10%
50V
16V
25V
25V
25V
< DIODE >
D1
D21
8-719-991-65 DIODE SB02W03C
8-719-423-10 DIODE MA8100-M-TX
D91 8-719-420-90 DIODE MA8051-M
D301 8-719-404-49 DIODE MA111
D351 8-719-422-97 DIODE MA8091-M (TA)
D352
D501
D502
D551
D552
D553 8-719-404-49 DIODE MA111
D571 8-719-034-94 DIODE MA4180-M (QZ)
D572 8-719-110-03 DIODE RD7.5ESB2
D581 8-719-017-62 DIODE MA8068-L-TX
D582 8-719-057-80 DIODE MA8160-M-TX
D584
D585
D586
D601
D621
8-719-404-49 DIODE MA111
8-719-400-20 DIODE MA152WA
8-719-911-19 DIODE 1SS119 (E)
8-719-400-20 DIODE MA152WA
8-719-404-49 DIODE MA111
8-719-034-94 DIODE MA4180-M (QZ)
8-719-035-74 DIODE MA4062-M (TA)
8-719-034-94 DIODE MA4180-M (QZ)
8-719-423-32 DIODE MA8120-M
8-719-035-54 DIODE MA4039-M (TA)
D622 8-719-911-19 DIODE 1SS119
D701 8-719-035-77 DIODE MA4068-L (TA)
D702 8-719-035-77 DIODE MA4068-L (TA)
– 38 –
Ref. No.
Part No.
Description
D703 8-719-035-74 DIODE MA4062-M (TA)
D704 8-719-035-74 DIODE MA4062-M (TA)
D705 8-719-035-74 DIODE MA4062-M (TA)
D706 8-719-035-74 DIODE MA4062-M (TA)
D707 8-719-034-94 DIODE MA4180-M (QZ)
D708 8-719-035-74 DIODE MA4062-M (TA)
D709 8-719-035-74 DIODE MA4062-M (TA)
D721 8-719-970-02 DIODE 1SR139-400
D722 8-719-970-02 DIODE 1SR139-400
D723 8-719-970-02 DIODE 1SR139-400
D724 8-719-970-02 DIODE 1SR139-400
D731 8-719-970-02 DIODE 1SR139-400
D732 8-719-970-02 DIODE 1SR139-400
D733 8-719-970-02 DIODE 1SR139-400
D734 8-719-970-02 DIODE 1SR139-400
D780 8-719-970-02 DIODE 1SR139-400
D781 8-719-049-38 DIODE 1N5404TU
D782 8-719-970-02 DIODE 1SR139-400
D783 8-719-970-02 DIODE 1SR139-400
D784 8-719-422-64 DIODE MA8062-M
D785 8-719-035-74 DIODE MA4062-M (TA) (E)
< IC >
IC301 8-752-079-78 IC CXA2509AQ-T4
IC331 8-759-443-67 IC LC75373ED
IC351 8-759-823-87 IC LB1638M
IC501 8-759-493-98 IC uPD17708GC-567-3B9
IC551 8-759-363-81 IC XC61AN4002PR
IC581 8-759-449-89 IC BA8270F-E2
IC611 8-759-347-49 IC BA3918-V2
IC751 8-759-490-74 IC TDA7384
< JACK >
Remark
J1 1-764-808-14 JACK (ANT) (ANT IN)
J331 1-774-699-12 JACK, PIN 4P (BUS AUDIO IN/LINE OUT REAR)
J561 1-566-822-41 JACK (REMOTE IN)
< CHIP CONDUCTOR >
JC1
JC2
JC3
JC4
1-216-296-00 SHORT 0
1-216-295-00 SHORT 0
1-216-295-00 SHORT 0 (US, Canadian)
1-216-296-00 SHORT 0
JC151 1-216-296-00 SHORT 0
JC161 1-216-295-00 SHORT 0
JC162 1-216-295-00 SHORT 0
JC163 1-216-296-00 SHORT 0
JC164 1-216-296-00 SHORT 0
JC251 1-216-296-00 SHORT 0
JC301 1-216-295-00 SHORT 0
JC302 1-216-295-00 SHORT 0
JC304 1-216-296-00 SHORT 0
JC331 1-216-296-00 SHORT 0
JC351 1-216-295-00 SHORT 0
JC501 1-216-296-00 SHORT 0
JC502 1-216-295-00 SHORT 0
JC503 1-216-296-00 SHORT 0
JC504 1-216-296-00 SHORT 0
JC506 1-216-296-00 SHORT 0
Ref. No.
Part No.
Description
JC507 1-216-296-00 SHORT 0
JC509 1-216-295-00 SHORT 0 (E)
JC510 1-216-295-00 SHORT 0
JC561 1-216-295-00 SHORT 0
JC581 1-216-296-00 SHORT 0
JC582 1-216-296-00 SHORT 0
JC601 1-216-296-00 SHORT 0
JC611 1-216-296-00 SHORT 0
JC751 1-216-296-00 SHORT 0
JC781 1-216-295-00 SHORT 0
JC901 1-216-295-00 SHORT 0 (US, Canadian)
JC903 1-216-295-00 SHORT 0 (E)
JC904 1-216-295-00 SHORT 0
JC961 1-216-296-00 SHORT 0
JC962 1-216-296-00 SHORT 0
JC963 1-216-296-00 SHORT 0
JC990 1-216-296-00 SHORT 0
JC991 1-216-296-00 SHORT 0
JC992 1-216-296-00 SHORT 0
JC993 1-216-296-00 SHORT 0
JC994 1-216-295-00 SHORT 0
< COIL >
L501
L781
L901
1-410-509-11 INDUCTOR 10uH
1-411-669-12 COIL, CHOKE
1-410-509-11 INDUCTOR 10uH
< TRANSISTOR >
Q21
Q22
Q171 8-729-920-21 TRANSISTOR DTC314TKH04
Q181 8-729-920-21 TRANSISTOR DTC314TKH04
Q271 8-729-920-21 TRANSISTOR DTC314TKH04
Q281 8-729-920-21 TRANSISTOR DTC314TKH04
Q351 8-729-015-11 TRANSISTOR 2SD1802FAST-TL
Q352 8-729-027-23 TRANSISTOR DTA114EKA-T146
Q353 8-729-900-53 TRANSISTOR DTC114EK
Q354 8-729-106-60 TRANSISTOR 2SB1115A
Q355 8-729-900-53 TRANSISTOR DTC114EK
Q551 8-729-027-23 TRANSISTOR DTA114EKA-T146
Q571 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q581 8-729-900-53 TRANSISTOR DTC114EK
Q601 8-729-423-99 TRANSISTOR 2SD2137-OP
Q602 8-729-900-53 TRANSISTOR DTC114EK
Q603 8-729-027-23 TRANSISTOR DTA114EKA-T146
Q621 8-729-027-23 TRANSISTOR DTA114EKA-T146
Q622 8-729-120-28 TRANSISTOR 2SC1623-L5L6
R1
R3
R4
R5
R6
R7
R8
8-729-120-28 TRANSISTOR 2SC1623-L5L6
8-729-021-94 TRANSISTOR 2SK1657-T1B
< RESISTOR >
1-216-049-11 RES, CHIP
1-216-061-00 METAL CHIP
1-249-429-11 CARBON
1-216-081-00 METAL CHIP
1-249-429-11 CARBON
1-216-109-00 METAL CHIP
1-247-899-11 CARBON
1K
3.3K
10K
22K
10K
330K
680K
5%
5%
5%
5%
5%
5%
5%
MAIN
Remark
1/10W
1/10W
1/4W
1/10W
(E)
1/4W
(E)
1/10W
1/4W
– 39 –
MAIN
Ref. No.
Part No.
R9
R10
R11
Description
1-216-180-00 RES, CHIP
1-216-073-00 METAL CHIP
1-249-413-11 CARBON
R12
R13
R14
R21
R22
R23
R24
R91
1-216-073-00 METAL CHIP
1-216-049-11 RES, CHIP
1-216-049-11 RES, CHIP
1-216-057-00 METAL CHIP
1-216-198-00 RES, CHIP
1-216-053-00 METAL CHIP
1-249-421-11 CARBON
1-216-049-11 RES, CHIP
R103 1-216-041-00 METAL CHIP
R104 1-216-109-00 METAL CHIP
R105 1-216-077-00 METAL CHIP
R106 1-216-079-00 METAL CHIP
R107 1-216-073-00 METAL CHIP
R108 1-216-081-00 METAL CHIP
R121 1-216-198-00 RES, CHIP
R121
R122 1-216-081-00 METAL CHIP
R141 1-216-073-00 METAL CHIP
R142 1-216-198-00 RES, CHIP
R151 1-216-049-11 RES, CHIP
R152
R152
R161 1-216-061-00 METAL CHIP
R171 1-216-033-00 METAL CHIP
R172 1-216-073-00 METAL CHIP
R174 1-216-129-00 METAL CHIP
R175 1-216-089-00 RES, CHIP
R181 1-216-033-00 METAL CHIP
R182 1-216-073-00 METAL CHIP
R184 1-216-129-00 METAL CHIP
R185 1-216-089-00 RES, CHIP
R186 1-216-182-00 RES, CHIP
R191 1-216-073-00 METAL CHIP
R192 1-216-097-00 RES, CHIP
R203 1-216-041-00 METAL CHIP
R204 1-216-109-00 METAL CHIP
R205 1-216-077-00 METAL CHIP
R206 1-216-079-00 METAL CHIP
R207 1-216-222-00 RES, CHIP
R208 1-216-081-00 METAL CHIP
R241 1-216-073-00 METAL CHIP
R242 1-216-049-11 RES, CHIP
R251 1-216-049-11 RES, CHIP
R252 1-216-077-00 METAL CHIP
R252
1-216-200-11 RES, CHIP
1-216-077-00 METAL CHIP
1-216-089-00 RES, CHIP
1-216-089-00 RES, CHIP
15K
18K
10K
22K
1K
1.5K
2.2K
1K
470
330K
180
10K
470
10K
1K
1K
2.2K
1K
1.2K
22K
10K
1K
1K
15K
47K
3.3K
220
10K
2.2M
47K
220
10K
2.2M
47K
220
10K
100K
470
330K
15K
18K
10K
22K
10K
1K
1K
15K
47K
R261 1-216-061-00 METAL CHIP
R271 1-216-033-00 METAL CHIP
R272 1-216-073-00 METAL CHIP
R274 1-216-129-00 METAL CHIP
R275 1-216-089-00 RES, CHIP
3.3K
220
10K
2.2M
47K
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
Remark
Ref. No.
Part No.
1/8W
1/10W
1/4W
R281
R282
R284
Description
1-216-033-00 METAL CHIP
1-216-073-00 METAL CHIP
1-216-129-00 METAL CHIP
R285 1-216-089-00 RES, CHIP
R286 1-216-033-00 METAL CHIP 1/10W
1/10W
1/10W
1/10W
1/8W
R301
R302
R303
1-216-079-00 METAL CHIP
1-216-097-00 RES, CHIP
1-216-065-00 METAL CHIP
R304 1-216-077-00 METAL CHIP
R305 1-249-429-11 CARBON 5%
5%
1/10W
1/4W
5% 1/10W
(US, Canadian)
5%
5%
1/10W
1/10W
R306
R307
R308
R331
1-249-429-11 CARBON
1-216-073-00 METAL CHIP
1-216-105-00 RES, CHIP
1-249-393-11 CARBON
R351 1-216-049-11 RES, CHIP
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
5% 1/8W
(US, Canadian)
R352
R353
R354
R501
R502
1-249-385-11 CARBON
1-216-065-00 METAL CHIP
1-216-073-00 METAL CHIP
1-216-097-00 RES, CHIP
1-216-097-00 RES, CHIP
5%
5%
5%
5%
5%
1/8W
1/10W
1/10W
1/8W
1/10W
1/10W
(US, Canadian)
1/10W
1/10W
1/10W
1/10W
(E)
(E)
R503 1-216-097-00 RES, CHIP
R504 1-216-097-00 RES, CHIP
R505 1-216-097-00 RES, CHIP
R506 1-216-057-00 METAL CHIP
R507 1-216-057-00 METAL CHIP
R508 1-216-057-00 METAL CHIP
R509 1-216-097-00 RES, CHIP
R510 1-249-441-11 CARBON
R511 1-216-699-11 METAL CHIP
R512 1-216-699-11 METAL CHIP
R513 1-208-826-11 RES, CHIP
R514 1-216-699-11 METAL CHIP
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/8W
1/10W
1/10W
1/10W
R516
R517
R518
1-216-097-00 RES, CHIP
1-216-097-00 RES, CHIP
1-216-097-00 RES, CHIP
R519 1-216-097-00 RES, CHIP
R522 1-216-097-00 RES, CHIP
R523 1-216-097-00 RES, CHIP
R524 1-216-097-00 RES, CHIP
R525 1-216-097-00 RES, CHIP
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/8W
1/10W
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
5%
(US, Canadian)
1/10W
(E)
1/10W
1/10W
1/10W
1/10W
1/10W
R526
R527
R528
R530
R531
R532 1-216-097-00 RES, CHIP
R533 1-216-097-00 RES, CHIP
R535 1-216-097-00 RES, CHIP
R537 1-216-246-00 RES, CHIP
R538 1-216-097-00 RES, CHIP
R539
R540
R541
R542
1-216-097-00 RES, CHIP
1-216-097-00 RES, CHIP
1-216-097-00 RES, CHIP
1-216-097-00 RES, CHIP
1-216-097-00 RES, CHIP
1-216-097-00 RES, CHIP
1-249-421-11 CARBON
1-249-421-11 CARBON
1-249-421-11 CARBON
68K
100K
100K
100K
100K
100K
100K
100K
100K
100K
100K
100K
100K
100K
100K
100K
100K
100K
100K
100K
100K
2.2K
2.2K
2.2K
10K
10K
220K
10
1K
2.2
4.7K
10K
100K
100K
220
10K
2.2M
47K
220
18K
100K
4.7K
15K
10K
100K
100K
100K
2.2K
2.2K
2.2K
100K
100K
100K
100K
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
Remark
1/10W
1/10W
1/10W
1/10W
1/10W
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
1/10W
1/10W
5% 1/4W
0.5% 1/10W
0.5% 1/10W
(E)
(E)
1/6W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/4W
1/4W
1/10W
1/10W
1/4W
1/10W
5%
5%
5%
5%
5%
2% 1/10W
(US, Canadian)
0.5% 1/10W
(US, Canadian)
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
5% 1/10W
(US, Canadian)
1/10W
(E)
1/10W
1/10W
1/8W
1/10W
1/10W
1/4W
1/4W
1/4W
– 40 –
MAIN
Ref. No.
Part No.
R543
R582
R583
R584
R601
R602
R704
R705
R706
R707
R708
Description
1-249-421-11 CARBON
R544 1-216-057-00 METAL CHIP
R545 1-249-429-11 CARBON
R546 1-249-413-11 CARBON
R551 1-216-097-00 RES, CHIP
R552 1-216-057-00 METAL CHIP
R561
R562
R563
R564
R571
1-208-806-11 RES, CHIP
1-208-806-11 RES, CHIP
1-216-025-00 RES, CHIP
1-216-025-00 RES, CHIP
1-216-097-00 RES, CHIP
R572 1-216-089-00 RES, CHIP
R573 1-216-089-00 RES, CHIP
R574 1-249-421-11 CARBON
R575 1-216-073-00 METAL CHIP
R581 1-216-073-00 METAL CHIP
1-216-025-00 RES, CHIP
1-247-807-31 CARBON
1-216-166-00 RES, CHIP
1-249-393-11 CARBON
1-249-395-11 CARBON
R603 1-216-186-00 RES, CHIP
R621 1-216-065-00 METAL CHIP
R701 1-216-025-00 RES, CHIP
R702 1-216-025-00 RES, CHIP
R703 1-216-057-00 METAL CHIP
1-216-057-00 METAL CHIP
1-216-057-00 METAL CHIP
1-216-206-00 RES, CHIP
1-216-049-11 RES, CHIP
1-208-806-11 RES, CHIP
R709 1-208-806-11 RES, CHIP
R710 1-216-025-00 RES, CHIP
R751 1-216-198-00 RES, CHIP
R752 1-216-049-11 RES, CHIP
R781 1-216-049-11 RES, CHIP
R901 1-216-057-00 METAL CHIP
R902 1-216-057-00 METAL CHIP
< SWITCH >
2.2K
2.2K
10K
470
100K
2.2K
10K
10K
100
100
100K
47K
47K
2.2K
10K
10K
100
100
47
10
15
330
4.7K
100
100
2.2K
2.2K
2.2K
2.2K
1K
10K
10K
100
1K
1K
1K
2.2K
2.2K
5%
5%
5%
5%
5%
5%
Remark
1/4W
1/10W
1/4W
1/4W
1/10W
1/10W
0.5% 1/10W
0.5% 1/10W
5%
5%
5%
1/10W
1/10W
1/10W
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
1/10W
1/10W
1/4W
1/10W
1/10W
1/10W
1/4W
1/8W
1/4W
1/4W
1/8W
1/10W
1/10W
1/10W
1/10W
5%
5%
5%
5%
1/10W
1/10W
1/8W
1/10W
0.5% 1/10W
0.5% 1/10W
5%
5%
5%
5%
5%
5%
1/10W
1/8W
1/10W
1/10W
1/10W
1/10W
S501 1-571-478-11 SWITCH, SLIDE (POWER SELECT)
S502 1-571-478-11 SWITCH, SLIDE (FREQUENCY SELECT) (E)
S551 1-692-431-21 SWITCH, TACTILE (RESET)
TU1
TU1
< TUNER >
A-3282-019-A TUNER UNIT TUX-008 (EA) (E)
A-3282-034-A TUNER UNIT TUX-010 (E) (US, Canadian)
< VIBRATOR >
X501 1-567-713-11 VIBRATOR, CRYSTAL (4.5MHz)
************************************************************
9
9
MISCELLANEOUS
**************
1-776-207-31 CORD (WITH CONNECTOR) (POWER)
(US, Canadian)
1-776-207-81 CORD (WITH CONNECTOR) (POWER) (E)
Ref. No.
Part No.
Description Remark
F781 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) (10A)
HP901 1-500-157-21 HEAD, MAGNETIC (PLAYBACK)
M901 A-3291-665-A MOTOR ASSY, MAIN (CAPSTAN/REEL)
************************************************************
#1
#2
#3
#4
#5
**************
HARDWARE LIST
**************
7-621-772-10 SCREW +B 2X4
7-685-793-09 SCREW +PTT 2.6X8 (S)
7-685-792-09 SCREW +PTT 2.6X6 (S)
7-685-794-09 SCREW +PTT 2.6X10 (S)
7-685-106-19 SCREW +P 2X10 TYPE2 NON-SLIT
#6
#7
7-624-104-04 STOP RING 2.0, TYPE-E
7-627-553-17 PRECISION SCREW +P 2X2 TYPE 3
************************************************************
ACCESSORIES & PACKING MATERIALS
********************************
506
507
507
3-861-687-11 MANUAL, INSTRUCTION (ENGLISH)
(US, Canadian)
3-861-687-21 MANUAL, INSTRUCTION (FRENCH) (Canadian)
3-861-687-31 MANUAL, INSTRUCTION
(ENGLISH, SPANISH, CHINESE) (E)
3-861-688-11 MANUAL, INSTRUCTION, INSTALL
(ENGLISH, FRENCH) (US, Canadian)
3-861-688-21 MANUAL, INSTRUCTION, INSTALL
(ENGLISH, SPANISH, CHINESE) (E)
X-3373-412-1 CASE (PANEL) ASSY (for FRONT PANEL)
************************************************************
PARTS FOR INSTALLATION AND CONNECTIONS
**************************************
501
502
503
504
505
3-916-161-31 FRAME ASSY
X-3370-077-1 SCREW ASSY (AE. KEY), FITTING (E)
3-924-961-01 SUPPORT (ND), FITTING (US, Canadian)
X-3370-076-1 SCREW ASSY (KEY), FITTING (US, Canadian)
X-3371-913-1 SCREW ASSY (J)
3-018-384-01 COLLAR
1-776-207-31 CORD (WITH CONNECTOR) (POWER)
(US, Canadian)
1-776-207-81 CORD (WITH CONNECTOR) (POWER) (E)
501
US, Canadian
503
505
502
504
E
506 507
– 41 –
XR-C5100
9-925-684-11
Sony Corporation
Personal & Mobile Communication Company
– 42 –
98A0536-1
Printed in Japan © 1998. 1
Published by Quality Assurance Dept.
Advertisement
Key features
- Cassette player
- 4-channel power amplifier
- FM tuner
- AM tuner (E Model)
- Shortwave tuner (E Model)
- Tone controls
- Power antenna control
- Telephone ATT control (E Model)
- Rear line out