Panasonic CQC1311NW, CQC1301NW, CQC1321NW Operating instructions

Panasonic CQC1311NW, CQC1301NW, CQC1321NW Operating instructions
MUTE/SQ
1
2
SCROLL
RANDOM
SCAN
3
4
5
REPEAT
TA/AF
6
Warning
PTY
DISP
Caution
This pictograph intends to alert you to the presence of
important operating instructions and installation instructions. Failure to heed the instructions may result in
injury or material damage.
Warning
Observe the following warnings when using this
unit.
❑ The driver should neither watch the display nor operate
the system while driving.
Watching the display or operating the system will distract the driver from looking ahead of the vehicle and can cause accidents.
Always stop the vehicle in a safe location and use the parking
brake before watching the display or operating the system.
❑ Use the proper power supply.
This product is designed for operation with a negative grounded
12 V DC battery system. Never operate this product with other battery systems, especially a 24 V DC battery system.
❑ Protect the Deck Mechanism.
Do not insert any foreign objects into the slot of this unit.
❑ Do not disassemble or modify the unit.
Do not disassemble, modify the unit or attempt to repair the product yourself. If the product needs to be repaired, consult your
dealer or an authorized Panasonic Service Centre.
❑ Do not use the unit when it is out of order.
If the unit is out of order (no power, no sound) or in an abnormal
state (has foreign objects in it, is exposed to water, is smoking, or
smells), turn it off immediately and consult your dealer.
❑ Refer fuse replacement to qualified service personnel.
When the fuse burns out, eliminate the cause and have it replaced
with the fuse prescribed for this unit by a qualified service engineer. Incorrect replacement of the fuse may lead to smoke, fire,
and damage to the product.
Observe the following warnings when installing.
❑ Disconnect the lead from the negative (–) battery terminal before installation.
Wiring and installation with the negative (–) battery terminal connected may cause electrical shock and injury due to a short circuit.
Some cars equipped with the electrical safety system have specific
procedures of battery terminal disconnection.
FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO THE
UNINTENDED ACTIVATION OF THE ELECTRICAL SAFETY SYSTEM
RESULTING IN DAMAGE TO THE VEHICLE AND PERSONAL
INJURY OR DEATH.
❑ Refer wiring and installation to qualified service personnel.
CAUTION
Keep the volume level low enough to be aware of road and traffic
conditions while driving.
❑ This unit is designed for use exclusively in automobiles.
❑ Do not operate the unit for a prolonged period with the
engine turned off.
❑ Follow the instructions to install and wire the product.
Otherwise these will raise the interior temperature of the unit, and
it may lead to smoke, fire, or other damage to the unit.
Exposure of the unit to water, moisture, or dust may lead to
smoke, fire, or other damage to the unit. Make especially sure that
the unit does not get wet in car washes or on rainy days.
❑ Use the designated parts and tools for installation.
Use the supplied or designated parts and appropriate tools to
install the product. The use of parts other than those supplied or
designated may result in internal damage to the unit. Faulty installation may lead to an accident, a malfunction or fire.
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
Do not take apart this unit or attempt to
make any changes yourself.
This unit is a very intricate device that uses a laser
pickup to retrieve information from the surface of
compact discs. The laser is carefully shielded so that
its rays remain inside the cabinet.
Therefore, never try to disassemble the player or alter
any of its parts since you may be exposed to laser
rays and dangerous voltages.
❑ Do not block the air vent or the cooling plate of the unit.
Blocking these parts will cause the interior of the unit to overheat
and will result in fire or other damage.
❑ Do not install the product where it is exposed to strong
vibrations or is unstable.
❑ Never use safety-related components for installation,
grounding, and other such functions.
If you need to open a hole in the vehicle chassis to attach or wire
the product, first check where the wire harness, gasoline tank, and
electric wiring are located. Then open the hole from outside if possible.
❑ Wear gloves for safety. Make sure that wiring is completed before installation.
❑ To prevent damage to the unit, do not connect the power
connector until the whole wiring is completed.
❑ Do not connect more than one speaker to one set of
speaker leads. (except for connecting to a tweeter)
❑ Never install the product in a location where it interferes
with your field of vision.
❑ Never have the power cord branched to supply other
equipment with power.
❑ After installation and wiring, you should check the normal operation of other electrical equipment.
Trim Plate
(YEFC051001)
Q'ty: 1
Power Connector
(YEAJ02874)
Q'ty: 1 set
Warranty Card
Q'ty: 1
Q'ty: 1
Removable Face Plate
Case
(YEFA131839)
Q'ty: 1
(CA-RC61EX)
Remote Control Unit (Option)
¡ This instruction manual explains operations for use with the buttons on the main unit. (Different operations excluded)
Note: The optional remote control unit is available from your local
dealer. (CA-RC61EX)
(ATT)
Power
PWR
Mode
(Source)
Band
Pause
MUTE
Mute
VOL
Volume
PRG
BAND/DISC UP
TUNE
TRACK
Tune
Track selection
Fast forward/fast reverse
For UK and Ireland customers only.
Customer Care Centre
¡
¡
¡
¡
For customers within the UK: 08705 357357
For customers within the Republic of Ireland: 01 289 8333
Visit our website for product information
E-mail: [email protected]
¡ Order accessories and consumable items for your product
with ease and confidence by phoning our Customer Care
Centre Monday - Thursday 9:00am - 5:30pm, Friday
9:30am - 5:30pm. (Excluding public holidays).
¡ Or go on line through our Internet Accessory ordering
application at www.panasonic.co.uk.
¡ Most major credit and debit cards accepted.
¡ All enquiries, transactions and distribution facilities are
provided directly by Panasonic UK Ltd.
¡ It couldn't be simpler!
¡ Also available through our Internet is direct shopping for a
wide range of finished products, so take a browse on our
website for further details.
Matsushita Electric Industrial Co., Ltd.
Web Site: http://www.panasonic.co.jp/global/
YEFM285600D NT1104-4055
Printed in China
Notes on
CD-Rs/RWs
Direct Sales at Panasonic UK
Printed side
¡ High bit rate and high sampling frequency are recommended for high quality sounds.
¡ Selecting VBR (Variable Bit Rate) is not recommended
because playing time is not displayed properly and sound
may be skipped.
¡ The playback sound quality differs depending on the encoding circumstances. For details, refer to the user manual of
your own encoding software and writing software.
¡ Direct sunlight
¡ Near car heaters
¡ Dirty, dusty and damp areas
¡ Seats and dashboards
¡ It is recommended to set the bit rate to “128 kbps or more”
and “fixed”.
Do not use irregularly shaped discs.
WMA
Use a dry, soft cloth to wipe from the centre outward.
¡ You are recommended to minimize the chances of making a disc that contains both CD-DA files and MP3/WMA
files.
¡ If CD-DA files are on the same disc as MP3 or WMA files,
the songs may not play in the intended order, or some
songs may not play at all.
¡ When storing MP3 data and WMA data on the same disc,
use different folders for each data.
¡ Do not record files other than MP3/WMA files and unnecessary folder on a disc.
¡ The name of MP3/WMA file should be added by rules as
shown in the following descriptions and also comply with
the rules of each file system.
q
Folder Selection
4
e
In the order
<Correct>
¡ You may encounter trouble in playing MP3/WMA files or
displaying the information of MP3/WMA files recorded with
certain writing software or CD recorders.
¡ The file extension “.mp3” or “.wma” should be assigned to
each file depending on the file format.
¡ This unit does not have the play list function.
¡ Although Multi-session recording is supported, the use of
Disc-at-Once is recommended.
Supported file systems
ISO 9660 Level 1/Level 2, Apple Extension to ISO 9660, Joliet,
Romeo
Note: Apple HFS, UDF 1.50, MIX mode CD, CD Extra is not
supported.
Compression formats
(Recommendation: “Points to remember when making
MP3/WMA files” on the right.)
¡ MPEG 1 audio layer 3
Bit rate: 32 k-320 kbps
VBR: Yes
Sampling frequency:
32, 44.1, 48 kHz
¡ MPEG 2 audio layer 3
Bit rate: 8 k-160 kbps
VBR: Yes
Sampling frequency:
16, 22.05, 24 kHz
¡ It is recommended to set the bit rate to “64 kbps or more”
and “fixed”.
¡ Do not set the copy protect attribute on the WMA file to
enable this unit to play back.
<Wrong>
¡ Windows Media
Audio Ver. 2, 8
Bit rate: 64 k-192 kbps
VBR: No
Sampling frequency:
32, 44.1, 48 kHz
Caution
¡ Never assign the “.mp3”, or “.wma” file
name extension to a file that is not in the
MP3/WMA format. This may not only produce noise from the speaker damage, but
also damage your hearing.
1
–
8
3
w
File Selection
In the order
–
y
q
5
ÇçàåÄçàÖ – ãÄáÖêçéÖ
àáãìóÖçàÖ
èêà
éíäêõíàà. àáÅÖÜÄíú
ÇéáÑÖâëíÇàü ãÄáÖêçéÉé
àáãìóÖçàü.
8
¡ MP3/WMA
Folder name
File name
¡ WMA (WMA tag)
Album name
Displayable characters
¡ Name files and folders in accordance with the standard of
each file system. Refer to the instructions of writing software for details.
¡ ASCII character set and special characters in each language
can be displayed.
Notes:
¡ With some software in which MP3/WMA format files have
been encoded, the character information may not be displayed properly.
¡ Undisplayable characters and symbols will be converted
into an asterisk ( ).
Be sure to select OFF when your car has no ACC position in the ignition switch. Failure to do this
could cause the battery to go dead.
For an ACC-equipped car, select ON. (a “Function
Settings”) The following functions are available. (Default:
off)
¡ The power is turned on automatically when inserting a
disc.
¡ The clock can be displayed even if the power is off.
: ACC not equipped (Default)
: ACC equipped
This operating instruction manual is for 3 models CQ-C1321NW, CQ-C1311NW and CQ-C1301NW. All illustrations throughout
this manual represent model CQ-C1321NW unless otherwise specified. The following table describes the differences among 3
models.
Features
Display colour
Models
Key/disc slot illumination colour
1Select the radio AM mode. (a “Radio (AM
[LW/MW]/FM )”)
CQ-C1311NW
CQ-C1301NW
Blue
Black
Black
Red
Red
Green
5 Press [DISP].
Minute blinks
6 Adjust the minute.
Minute entered
[[]: sets the minute ahead.
[]]: sets the minute back.
7 Press [DISP].
Completed
2 Press [DISP].
(clock display)
3 Hold down [DISP] for more than 2 secCQ-C1321NW
[[]: sets the hour ahead.
[]]: sets the hour back.
onds.
Hour blinks
Clock Display at Power Off
Press [DISP] to change the display. (ACC ON)
Display off
4 Adjust the hour.
Hour entered
7
Tree 1
Tree 2
Tree 3
y
Tree 4
Tree 8
(Max.)
Your product is designed and manufactured to ensure the minimum of maintenance. Use a dry, soft cloth for routine
exterior cleaning. Never use benzine, thinner, or other solvents.
Warning
¡ Use fuses of the same specified rating (15 A). Using substitutes or fuses with higher ratings, or connecting the unit directly without a fuse could cause fire or damage to the unit. If the replaced fuse fails, contact your nearest authorized
Panasonic Service Centre.
Maximum number of files/folders
¡ Maximum number of files: 999
¡ Maximum number of files in one folder: 255
¡ Maximum depth of trees: 8
¡ Maximum number of folders: 255 (Root folder is included.)
Notes:
¡ This unit counts the number of folders irrespective of the
presence or absence of MP3/WMA file.
¡ If the selected folder does not contain any MP3/WMA files,
the nearest MP3/WMA files in the order of playback will be
played.
¡ Playback order may be different from other MP3/WMA
players even if the same disc is used.
¡ “ROOT” appears when displaying the root folder name.
Windows Media, and the Windows logo
are trademarks, or registered trademarks of Microsoft Corporation in the
United States and/or other countries.
Copyright
It is prohibited by copyright laws to copy, distribute and
deliver copyrighted materials such as music without the
approval of copyright holder except enjoying yourself personally.
Anti-Theft System
Power supply
Current consumption
Maximum power output
Tone adjustment range
Speaker impedance
Pre-amp output voltage
Pre-amp output impedance
Dimensions (W x H x D)
Weight
DC 12 V (11 – 16 V), test voltage 14.4 V, negative ground
Less than 2.2 A (CD mode; 0.5 W 4 channels)
50 W x 4 (at 1 kHz), volume control maximum
Bass: ±12 dB at 100 Hz, Treble: ±12 dB at 10 kHz
4–8Ω
2.5 V (CD mode, 1 kHz, 0 dB)
200 Ω
178 x 50 x 160 mm
1.3 kg
Sampling frequency
DA converter
Pick-up type
Light source
Wave length
Frequency response
Signal to noise ratio
Total harmonic distortion
Wow and flutter
Channel separation
8 times oversampling
1 bit DAC System
Astigma 3-beam
Semiconductor laser
790 nm
20 Hz – 20 kHz (±1 dB)
96 dB
0.01 % (1 kHz)
Below measurable limits
75 dB
This unit is equipped with a removable face plate. Removing this face plate makes the unit totally inoperable.
Caution
¡ This face plate is not waterproof. Do not expose it to
water or excessive moisture.
¡ Do not remove the face plate while driving your car.
¡ Do not place the face plate on the dashboard or nearby
areas where the temperature rises high.
Above description complies with our investigations as of
December 2004. It has no warranty for reproducibility and
displayability of MP3/WMA.
¡ Do not touch the contacts on the face plate and the main
unit, since this may result in poor electrical contact.
¡ If dirt or other foreign substances get on the contacts,
wipe them off with a clean and dry cloth.
Removing
Mounting
1 Turn off the power.
2 Press [ ]. The face plate will open.
3 Pull it out toward you.
4 Put the face plate in the case.
1 Slide the left side of the face plate in place.
2 Press the right end of face plate until a
Frequency Range
Usable Sensitivity
Stereo Separation
87.5 MHz – 108 MHz
6 dB/µV (S/N 30 dB)
35 dB (at 1 kHz)
AM (MW)
Frequency Range
Usable Sensitivity
531 kHz – 1 602 kHz
28 dB/µV (S/N 20 dB)
Frequency Range
Usable Sensitivity
153 kHz – 279 kHz
32 dB/µV (S/N 20 dB)
“click” is heard.
Notes:
¡ Specifications and design are subject to modification without notice due to improvements.
¡ Some figures and illustrations in this manual may be different from your product.
2
1
2
FM
AM (LW)
1
No warranty
Clock display
Specifications
If the replaced fuse fails, contact your nearest authorized Panasonic Service Centre.
Title name/Artist name
Title name/Artist name
Note: If you would like to turn on the power and make the
demonstration message appear, hold down [SRC] (PWR)
for more than 4 seconds (ACC ON).
t
Displayed items
¡ MP3 (ID3 tag)
Album name
[SRC] (PWR: Power).
2 Press
The demonstration screen appears.
r
Display Information
¡ CD-TEXT
Disc title
Track title
appears.
position.
The 24-hour system is used for the clock.
Notes:
¡ Adjust the clock when “NO CT” appears on the display.
¡ When a broadcast of FM Radio Data System is
received, the clock is adjusted automatically by the
Clock Time service.
¡ Hold down []] or [[] to change numbers rapidly.
6
MP3
Disc cleaning
Recording MP3/WMA files on a CD-media
2
Common
MODE
Car Audio
Sales and Support Information
Points to remember when making MP3/WMA files
TEXT
Do not use irregularly shaped discs.
Do not leave discs in the following places:
¡ You may have trouble playing back some CD-R/RW discs
recorded using CD recorders (CD-R/RW drives), either due
to their recording characteristics or dirt, fingerprints,
scratches, etc. on the disc surface.
¡ CD-R/RW discs are less resistant to high temperatures and
high humidity than ordinary music CDs. Leaving them
inside a car for extended periods may damage and make
playback impossible.
¡ Some CD-R/RWs cannot be played back successfully due
to incompatibility among writing software, a CD recorder
(CD-R/RW drive) and the discs.
¡ This player cannot play the CD-R/RW discs if the session is
not closed.
¡ This player cannot play the CD-R/RW discs which contain
other than CD-DA or MP3/WMA data (Video CD, etc.).
¡ Be sure to observe the instructions of the CD-R/RW disc
for handling it.
Root Folder
(Root Directory)
1
¡ Do not touch the underside of a disc.
¡ Do not scratch on a disc.
¡ Do not bend a disc.
¡ When not in use, keep a disc in a case.
Do not attach any seals or labels to your discs.
Do not write on the disc label with a ballpoint pen or
other hard-point pens.
Folder selection order/file playback order
(Anti-Theft System)
(English, Deutsch, Français,
Nederlands : YEFM293892)
(Svenska, Italiano, Español,
Dansk
: YEFM293893)
Q'ty: 1
ADVARSEL – LASER
UDSENDES NÅR DER
ER ÅBNET. UNDGÅ
UDSÆTTELSE FOR
STRÅLER.
Maintenance
Cleaning the
Unit
Q'ty: 1 set
Installation Instructions
Note: MP3/WMA encoding and writing software is not supplied with this unit.
How to hold a disc
A D V A R S E L – LA S E R STRÅLING.
UNNGÅ
E K S P O N E R IN G F O R
STRÅLEN VED ÅPNING.
Panasonic welcomes you to our constantly growing family of electronic products owners.
We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully selected components, and
assembled by people who are proud of the reputation their work has built for our company. We know this product will bring you many hours of
enjoyment, and after you discover the quality, value and reliability we have built into it, you too will be proud to be a member of our family.
Fuse
(YEFX0217263)
Notes on MP3/WMA
If you use commercial CDs, they must have the label
shown at right.
Some copy-protected music CDs are not playable.
ATTENTION –
RAYONNEMENT LASER
SI OUVERT, ÉVITER
TOUTE EXPOSITION AU
FAISCEAU.
Before Reading These Instructions
Face Plate Removing/Mounting
Q'ty: 1
Mounting Collar
Notes on Discs
Notes on MP3/WMA
Q'ty: 2
Mounting Bolt
Notes:
¡ The number in parentheses underneath
each accessory part name is the part
number for maintenance and service.
¡ Accessories and their part numbers are
subject to modification without prior
notice due to improvements.
¡ Mounting Collar and Trim Plate are
mounted on the main unit at shipment.
Notes on CD/CD Media (CD-ROM, CD-R, CD-RW)
Installation kit (YEP0FZ5700)
Lock Cancel Plate
[DISP] (Display).
3 Press
The demonstration screen is cancelled, and no more
Deck Ass’y (in the unit,
upper side)
Differences among 3
models
¡Please read these instructions carefully before using this product and keep this manual for future reference.
ACC
ON
Caution
FÖRSIKTIGHET –
LASERSTRÅLNING I
ÖPPNAT LÄGE. UNDVIK
ATT UTSÄTTAS FÖR
STRÅLEN.
The product should be installed in a horizontal position with the
front end up at a convenient angle, but not more than 30˚.
The user should bear in mind that in some areas there may be
restrictions on how and where this unit must be installed. Consult
your dealer for further details.
TEXT
(English
: YEFM285600)
(Deutsch : YEFM285601)
(Français : YEFM285602)
(Nederlands : YEFM285603)
(Svenska : YEFM285604)
(Italiano
: YEFM285605)
(Español
: YEFM285606)
(Dansk
: YEFM285607)
VORSICHT - LASERSTRAHLUNG,
WENN
GEÖFFNET. VERMEIDEN
SIE EIN AUSSETZEN
GEGENÜBER
DEM
LASERSTRAHL.
your car's ignition
1 Set
switch to the ACC or ON
V A R O IT U S – LA S E R SÄTEILYVAARA
AVATTAESSA. VARO
ALTISTUMISTA
SÄTEELLE.
❑ Installation Angle
❑ Installing the product on the air bag cover or in a location
where it interferes with airbag operation is prohibited.
❑ Check for piping, gasoline tank, electric wiring, and other
items before installing the product.
❑ In the case of installation to an airbag-equipping car,
confirm warnings and cautions of the vehicle manufacturer before installation.
❑ Make sure the leads do not interfere with driving or getting in and out of the vehicle.
❑ Insulate all exposed wires to prevent short circuiting.
Operating Instructions
CAUTION - LASER RADIATION WHEN OPEN.
AVOID EXPOSURE TO
BEAM.
Avoid slanted or strongly curved surfaces for installation. If the
installation is not stable, the unit may fall down while driving and
this can lead to an accident or injury.
Do not use safety-related vehicle components (fuel tank, brake,
suspension, steering wheel, pedals, airbag, etc.) for wiring or fixing the product or its accessories.
The continuation of their using in abnormal conditions may cause
fire, electrical shock or a traffic accident.
Accessories
Caution Label
This product utilizes a laser.
❑ Take care not to damage the leads.
❑ Do not expose the unit to direct sunlight or excessive
heat.
❑ Do not use the product where it is exposed to water,
moisture, or dust.
Caution
Not following the instructions to properly install and wire the product could cause an accident or fire.
When wiring, take care not to damage the leads. Prevent them
from getting caught in the vehicle chassis, screws, and moving
parts such as seat rails. Do not scratch, pull, bend or twist the
leads. Do not run them near heat sources or place heavy objects
on them. If leads must be run over sharp metal edges, protect the
leads by winding them with vinyl tape or similar protection.
CLASS 1 LASER PRODUCT
LASER RADIATION WHEN OPEN. DO NOT STARE
INTO BEAM.
Installation of this unit requires special skills and experience. For
maximum safety, have it installed by your dealer. Panasonic is not
liable for any problems resulting from your own installation of the
unit.
❑ Keep the sound volume at an appropriate level.
Operating the audio system for a long period of time with the
engine turned off will drain the battery.
(CQ-C1321NW)
Label Indications and Their Locations
First Time Power On
SRC
D·M
This pictograph intends to alert you to the presence of
important operating instructions and installation instructions. Failure to heed the instructions may result in
severe injury or death.
Observe the following cautions when using this
unit.
Observe the following cautions when installing.
ACC Setting
PWR
PUSH SEL
APM
CQ-C1321N
E/TRACK
TUN
BAND
ER
LD
FO
L
Caution
Clock Setting
VO
safely and to alert you to potential dangers resulting from improper
connections and operations. The meanings of the pictographs are
explained below. It is important that you fully understand the meanings of the pictographs in order to use this manual and the system
properly.
General
Operating Instructions
■ This manual uses pictographs to show you how to use the product
Disc Player
nents of your car audio system carefully before using the system.
They contain instructions about how to use the system in a safe and
effective manner. Panasonic assumes no responsibility for any problems resulting from failure to observe the instructions given in this
manual.
Radio
■ Read the operating instructions for the unit and all other compo-
Laser Product
CQ-C1321NW/C1311NW/C1301NW
English
WMA MP3 CD Player/Receiver
Preparation
Safety Information
Clock display
Radio (AM [LW/MW]/FM)
Band
Frequency Preset Number
Disc slot
takes a disc in with the printed side facing
up.
Notes:
¡ The power will be turned on automatically when a disc is loaded at ACC ON.
¡ A disc which has both CD-DA data and
MP3/WMA data on it may not be reproduced normally.
Display change
Press [DISP] to change the display.
AM (LW/MW) mode:
Band/frequency
SCAN
3
4
5
TA/AF
6
MUTE/SQ
1
RANDOM
SCAN
3
4
5
REPEAT
PTY
TA/AF
DISP
6
[1] to [6]
selects a preset station in the radio source,
and presets the current station. (Hold it down
for more than 2 seconds.)
[DISP] (Display)
switches the information on
the display.
[TUNE ]] [TUNE []
down/up the frequency. (Hold it down for
more than 0.5 seconds and release it for seek
tuning.)
Band/frequency
PS
CT
Mute
(VOCAL) clear sound:
emphasizes middle tone and slightly emphasizes treble.
lights.)
3 Select a station.
Auto Preset Memory (APM)
Frequency adjustment
Note: Hold down either of them for more than 0.5 seconds and release it for seek tuning.
Preset station selection
Press the corresponding preset button from [1] to [6] to
tune into a preset station.
Manual station preset
1 Tune into a station.
2 Hold down one of the preset buttons from
seconds.
Check point
No sound
Noise
No sound from
left, right, front,
or rear speaker
Left and right
sounds are
reversed
● Disable the mute function.
● Verify the wiring.
● Wait until the dew disappears before
turning on the unit.
● Make sure that grounding is established
properly.
● Adjust the balance and fader.
● Verify the wiring.
● Connect the speaker lead correctly.
Disc Player
No sound, or disc
is automatically
ejected
The following functions are available when the AF mode is
active (
lights).
Preset data
deleted
● The preset memory is cleared to return
to the original factory setting when the
power connector or battery is disconnected.
¡ When receiving conditions become bad, a station with better receiving conditions is automatically tuned in to.
¡ When executing APM, only RDS stations are selected.
¡ When calling up a preset station, a best receiving station is
selected automatically. (BSR Best Stations Research)
TA (Traffic Announcement)
(The disc is ejected automatically.)
The disc is dirty, or is upside down.
● Check the disc.
(The disc is ejected automatically.)
The disc has scratches.
● Check the disc.
The following functions are available when the PTY mode is
active.
Sound skip,
poor sound
quality
● Clean the disc.
A WMA file can be copyrighted.
● The file protected by copyright is not
playable.
Sound skip
due to
vibration
● The maximum permissible tilt angle is
30°.
● Secure the unit.
TA (Traffic
Announcement)
PTY (Programme Type)
[DISP] (Display)
switches the information on the
display.
DISP
[}] [{]
skip to the previous/next folder.
indicator
Folder number
Track title
Folder name/
Album*
File name/
Title, artist*
Clock
File number
*ID3/WMA Tag On/Off
Hold down [3] for more
than 2 seconds.
Play Mode indicators
album title and song title/
artist name are displayed.
(Default)
folder name/file name are
displayed.
Notes:
¡ For scrolling text, press [3] (SCROLL).
¡ “NO TEXT” is displayed when there is no information on the
disc.
¡ If you insert an 8 cm disc and cannot eject it, turn ACC of your car
off once and turn it on again, then press [u] (Eject).
¡ Do not insert foreign objects into the disc slot.
¡ Do not insert a disc when the
indicator lights.
¡ Refer to the section of “Notes on Discs” and “Notes on
MP3/WMA”.
¡ This unit does not support 8 cm discs.
Random play
2 Select a desired portion.
Note: New stations overwrite existing saved stations.
The preset stations under best receiving conditions are
received for 5 seconds each after presetting the stations
(SCAN). To stop scanning, press one of the buttons from
[1] to [6].
Press [{] / [}].
Pause
Track/file selection
Press [BAND] (y / 5).
Press [6] / [7].
Press again to cancel.
Note: To perform fast forward/reverse, hold down either
of them.
Disc Player (CD-DA disc):
Previous/next track
Folder repeat play (MP3/WMA)
All the available songs (tracks/files) are played in a random
sequence.
Folder selection (MP3/WMA)
source.
(blinks once)
The current folder is repeated.
Press [4] (RANDOM).
Hold down [6] (REPEAT) for more than 2
seconds.
Press again to cancel.
Hold down again to cancel.
Folder random play (MP3/WMA)
Scan play
All the available files in current folder are played in a random
sequence.
The first 10 seconds of each songs (tracks/files) is played in
sequence.
Hold down [4] (RANDOM) for more than 2
seconds.
Hold down again to cancel.
Press [5] (SCAN).
Press again to cancel.
Folder scan play (MP3/WMA)
Repeat play
From the next folder, the first 10 seconds of the first file on
each folder is played in sequence.
The current song (track/file) is repeated.
Press [6] (REPEAT).
Hold down [5] (SCAN) for more than 2
seconds.
For listening to only traffic information, activate TA and set the
volume to 0 in FM mode.
Once traffic information starts, the volume changes to the TA
volume. (a “Audio Settings”)
[VOL] (Volume)
selects a value in the audio menu.
(PUSH SEL) (Push to select)
selects items in the audio menu.
VO
BAND
APM
SRC
Programs can be searched for by use of PTY that has been
originally preset.
Press [1] to [6] to select PTY in the PTY mode.
RDS information is updated constantly in response to the
current position.
1
2
EON-TA
If reception becomes poor when tuning in a preset station,
press the same preset number button. The same station with
better reception will be searched for.
Press same preset number button again to cancel.
Note: For PI Seek, cancel the TA mode first, then execute PI
Seek.
CQ-C1321N
MUTE/SQ
SCROLL
RANDOM
SCAN
3
4
5
2
REPEAT
VO
BAND
TA/AF
6
3
4
5
6
Programme Type
NEWS
SPEECH
SPORT
POP M
CLASSICS
MUSIC
Contents
NEWS
AFFAIRS, INFO, EDUCATE,
DRAMA, CULTURE, SCIENCE,
VARIED, WEATHER, FINANCE,
CHILDREN, SOCIAL, RELIGION,
PHONE IN, TRAVEL, LEISURE,
DOCUMENT
SPORT
POP M
CLASSICS
ROCK M, EASY M, LIGHT M,
OTHER M, JAZZ, COUNTRY,
NATION M, OLDIES, FOLK M
Another station in the same PTY is searched for by pressing
[BAND].
Notes:
¡ When there is no corresponding programme type station,
“NONE” is displayed.
¡ A desired PTY appears for 5 seconds.
¡ Preset contents are changeable.
1 Press []] or [[] to select PTY.
SPEECH
INFO
CULTURE
ROCK M
OTHER M
SOCIAL
LEISURE
OLDIES
/
/
/
/
/
/
/
/
MUSIC /
SPORT /
SCIENCE /
EASY M /
WEATHER/
RELIGION /
JAZZ
/
FOLK M /
NEWS
/
EDUCATE /
VARIED /
LIGHT M /
FINANCE /
PHONE IN /
COUNTRY /
DOCUMENT
2 Press [VOL] (PUSH SEL) to select a
mode to be adjusted.
AFFAIRS /
DRAMA /
POP M /
CLASSICS /
CHILDREN /
TRAVEL /
NATION M /
PWR
PTY
1
(Setting Range: –12 dB to +12 dB by 2 dB,
Default: 0 dB)
¡ When there is no corresponding programme type station,
“NONE” is displayed.
3 Turn [VOL] clockwise or counterclock-
PTY Preset Change
1
2 Follow the procedure of ordinary presetting.
FM Monaural
q : Up
w : Down
q : Increased
w : Decreased
q : Increased
w : Decreased
q : Right enhanced
w : Left enhanced
(a “Station Preset” in “Radio (AM
[LW/MW]/FM)”)
q : Front enhanced
w : Rear enhanced
FM Local
AM Local
PTY
DISP
[DISP] (Display)
exits from the function
menu.
3 Turn [VOL] clockwise or counterclockwise
to adjust.
MONO OFF
MONO ON
(
lights.)
LOCAL ON
(
lights.)
LOCAL ON
(
lights.)
Set to OFF if your car has no
ACC position.
ACC Selection
(Default: OFF)
(a “Preparation”)
Set to ON if your car has an
ACC position.
RDS
(Default: OFF)
Note: When the Region mode is switched from OFF to
ON or vice versa, the AF mode turns on automatically.
PTY Language
RDS
The frequency is changed
also for programs outside the
region.
The frequency is changed
only for programs within the
region.
English
(Default: ENGLISH)
TA Volume Set
(Setting Range: 1 to 40, Default: 18)
TA/AF
6
LOCAL OFF
AM
Only stations with good reception are detected in seek
tuning.
(Default: OFF)
Region
q : Increased
w : Decreased
REPEAT
LOCAL OFF
FM
Only stations with good reception are detected in seek
tuning.
(Default: OFF)
External Mute
Allows you to mute the current source while
Panasonic navigation system provides voice guidance or car telephone conversation is in progress.
(Setting Range: 0 (no sound), 1 (decrease 15
steps), 2 (decrease 10 steps) and OFF
(unchanged), Default: 0)
FM
Noise is significantly decreased when weak signals are
received from an FM broadcast station.
(Default: OFF)
Fader
(Setting Range: 15 levels each, Default CNT (centre))
5
mode to be adjusted.
Original PTY presets can be changed as you like.
Select a PTY that you would like to preset.
SCAN
4
2 Press [VOL] (PUSH SEL) to select a
wise to adjust.
Balance
(Setting Range: 15 levels each, Default CNT (centre))
RANDOM
3
Note: If no operation takes place for more than 7 seconds in the function menu, the display returns to the regular
mode.
Treble
(Setting Range: –12 dB to +12 dB by 2 dB,
Default: 0 dB)
SCROLL
play.
Search starts.
Notes:
¡ To stop searching, press [BAND] (SET).
2
D·M
1 Hold down [VOL] (PUSH SEL) for more than 2 seconds to display the function menu dis-
Bass
2 Press [BAND].
MUTE/SQ
SRC
[DISP] (Display)
exits from the audio menu.
Volume
(Setting Range: 0 to 40, Default: 18)
CQ-C1321N
APM
DISP
ER
LD
FO
L
D·M
Note: If no operation takes place for more than 7 seconds in the audio menu (2 seconds in Main volume adjustment), the display returns to the regular mode.
Detailed PTY Selection
Programme Search by PTY
EON (Enhanced Other Network)
PI Seek (Programme Identification Seek)
ER
LD
FO
L
1
Holding down [DISP] (PTY) for more than 2 seconds toggles
PTY mode on and off.
As well as the frequency, the name of the broadcast station
appears.
Emergency announcement automatically appears on the
display when it is received.
[VOL]
selects a value in the function menu.
(PUSH SEL) (Push to select)
selects items in the function menu.
PWR
The clock is automatically adjusted.
Low level AF operating sensitivity. (Default)
When the AF network of an RDS station is not
required.
Pressing [TA] toggles TA on and off.
CT (Clock Time)
Emergency Announcement Reception
High level AF operating sensitivity.
Traffic Information Only (TA Mute)
PTY On/Off
Other functions of RDS
¡ A TP station is automatically searched for and received at
the instant of toggling the TA mode on if you are receiving
a non-TP station or TP station with poor reception.
¡ When executing station search or APM, only TP stations
are selected.
Function Settings
1 Press [VOL] (PUSH SEL) to display the audio menu display.
Note: PTY language can be selected. (a “Function Settings”)
Traffic information from the current and other network
stations can be received.
Hold down [TA] (AF) for more than 2 seconds to select AF
level.
TA On/Off
¡ The PTY of receiving station appears.
¡ Programs can be searched for by PTY.
The following functions are available when the TA mode is active
(
lights).
AF Level
● Press [u]. If the disc is still not ejected,
contact the nearest Panasonic Service
Centre.
¡ Setting to TA on with the unit in another mode, it will automatically switch to radio mode and output the traffic
announcement when the traffic announcement begins. The
traffic announcement having finished, the unit will return to
the previous mode. (TA Standby Mode)
No operation by some cause.
● If normal operation is not restored, consult your dealer or the nearest Service
Centre to ask for repairs.
Cannot read the file
● Check the file.
TA/AF
6
Audio Settings
PS (Programme Service Name)
Notes:
¡ The AF sensitivity can be adjusted.
¡ The AF available range can be adjusted. (a “Function
Settings”)
Error Display Messages
● Load the disc correctly.
● Clean the disc.
Disc not
ejectable
AF (Alternative Frequency)
AF (Alternative Frequency)
No power
Some FM stations are broadcasting added data compatible
with RDS. This radio set offers convenient functions using
such data.
RDS service availability varies with areas. Please understand if
RDS service is not available in your area, the following service
is not available, either.
The following functions are available when receiving RDS
stations.
Check point
● Tune in to another station of high-intensity waves.
● Make sure that the antenna mounted
point is grounded properly.
Play time
Hold down again to cancel.
¡ Do not use the unit in an irregular condition, for example, without sound, or with smoke or a foul smell, which can cause
ignition or electric shock. Immediately stop using the unit and
consult your dealer.
¡ Never try to repair the unit by yourself because it is dangerous
to do so.
Frequent
noise
Disc title
Clock
Press again to cancel.
Radio
● Start the engine. (Or turn the ignition
switch to the ACC position.)
● Verify the wiring. (battery lead, power
lead, ground lead, etc.)
● Fuse blown (Contact the nearest
Panasonic Service Centre.)
● Ask a professional for fuse replacement.
● Be sure to use the same rated fuse.
REPEAT
Previous/next file
What is RDS?
Common
5
Disc Player (MP3/WMA disc):
Useful functions such as AF, TA, PTY are available in the RDS (Radio Data System)-ready areas.
Trouble
Normal
MP3/WMA mode display
lights when folder random/repeat/scan is on.
PUSH SEL
Trouble
SCAN
4
1 Press [SRC] to select the Disc Player
Radio Data System (RDS) in FM Broadcasting
Warning
RANDOM
3
PUSH SEL
Check and take steps as described below.
If the described suggestions do not solve the problem, it is recommended to take the unit to your nearest authorized Panasonic Service
Centre. The product should be serviced only by qualified personnel.
Please refer the checking and the repair to professionals. Panasonic
shall not be liable for any accidents arising out of neglect of checking
the unit or your own repair after your checking.
SCROLL
2
PTY
[1] to [6] for more than 2 seconds.
Note: New stations overwrite existing saved stations.
PTY (Programme Type)
If You Suspect Something Wrong
[SRC] (Source)
selects a source.
With this operation, stations with good receiving conditions can
be automatically stored in the preset memory.
1 Select a band.
2 Hold down [BAND] (APM) for more than 2
Normal
(RANDOM)/(SCAN)/(REPEAT)
toggles on/off each play mode.
(SCROLL)
scrolls the information on display.
Notes:
¡ If no operation takes place for more than 5 seconds in
the SQ selection mode, the display returns to the regular
mode.
¡ Settings of SQ, bass and treble are influenced one another. If such an influence causes distortion to the audio
signal, readjust bass/treble or volume.
Troubleshooting
MUTE/SQ
D·M
RDS mode:
Up to 6 stations can be preset in AM (LW/MW), FM1, FM2, and
FM3 respectively.
Preset stations can be simply called up by pressing one of the
preset buttons from [1] to [6].
[TUNE ]]: Lower
[TUNE []: Higher
Operation Flow
(POP) wide-ranged and deep sound:
slightly emphasizes bass and treble.
L
1
Operation Flow
(FLAT) flat frequency response:
does not emphasize any part. (Default)
(Setting Range: 0 to 40, Default: 18)
Turn [VOL].
ON: Press [MUTE]. (
OFF: Press [MUTE] again.
1 Press [SRC] to select the radio source.
2 Press [BAND] to select a band.
as follows:
(ROCK) speedy and heavy sound:
exaggerates bass and treble.
Disc Player (CD-DA disc): Disc Player (MP3/WMA disc):
Caution
ond activates the SQ selection mode.
Volume Adjustment
ER
LD
FO
CQ-C1321N
PWR
Band/frequency
1 Holding down [SQ] for more than 1 sec-
Disc Player
BAND
APM
SRC
SQ is a function that can call up various sound types at the
touch of button in accordance with your listening music
type.
Press [SRC] to change the source.
VO
CT
2 Press [SQ] to select the sound type (SQ)
Source Selection
(y / 5) (Pause/Play)
toggles pause/play in the
player source.
PS (Programme Service name)
Station Preset
Power on: Press [SRC] (PWR).
Power off: Hold down [SRC] (PWR) for
more than 1 second.
[u] (Eject)
ejects the disc.
PUSH SEL
[SRC] (Source)
selects a source.
SCROLL
2
D·M
Press [DISP] to change the display.
Play Mode indicators
FM (not RDS) mode:
SQ (Sound Quality)
Set your car's ignition switch to the ACC or ON position.
Radio
SRC
E/TRACK
TUN
PWR
PTY
DISP
[MUTE]
toggles mute on/off.
(SQ) (Sound Quality)
selects a sound type (SQ). (Hold it down for
more than 1 second.)
Power On/Off
General Operations
REPEAT
CQ-C1321N
Display change
Play time
E/TRACK
TUN
2
RANDOM
L
Track number
Random, Repeat, Scan
1
SCROLL
APM
CD-DA mode display
Function Menu
MUTE/SQ
SRC
BAND
D·M
ER
LD
FO
Radio Source Display
PWR
VO
PUSH SEL
PUSH SEL
APM
[SRC] (Source)
selects a source.
(PWR) (Power)
toggles power on/off.
ER
LD
FO
CQ-C1321N
E/TRACK
TUN
BAND
VO
L
CT (Clock Time)
[6] [7]
skip to the previous/next track/file in the player
mode.
Hold down either of them for fast reverse/fast forward.
E/TRACK
TUN
Remote control sensor
for an optional remote control unit (CA-RC61EX).
lights while receiving an FM stereo signal.
Player Source Display
[BAND]
selects a band in the radio source.
(APM) (Auto Preset Memory)
executes APM in the radio source. (Hold it
down for more than 2 seconds.)
Audio menu
[VOL] (Volume)
Disc Player
E/TRACK
TUN
General
Swedish
q : Increased
w : Decreased
Note: If the fader is set to front, the pre-amp. output (rear) is decreased.
Prenez contact avec un spécialiste pour le montage.
(for non-ISO connector)
Vraag een vakman voor de installatie.
Apply insulating tape to bare leads.
Secure loosened leads.
●Verify the radio using the antenna and speakers before installation.
Wenden Sie sich zum Einbau an einen Fachmann.
●Vérifiez l’autoradio avant de procéder au montage.
●Controleer voor de installatie of de radio werkt met de antenne en
de luidsprekers.
WMA MP3 CD Player/Receiver
CQ-C1321NW/C1311NW/C1301NW
●Mounting angle side to side : horizontal
front to rear : 0 – 30°
BAND
APM
PWR
SRC
VO
L
ER
LD
FO
CQ-C1321N
PUSH SEL
Dieses Gerät ist ausschließlich für den Anschluss
an Bordnetze mit 12 V Batterie und negativer (–) Klemme
an Masse bestimmt.
Schließen Sie den Versorgungsleiter (rot) zum Schluss an
MUTE/SQ
1
2
SCROLL
RANDOM
SCAN
3
4
5
REPEAT
D·M
TA/AF
6
PTY
English
●Probieren Sie den Radiobetrieb vor dem Einbau mit Antenne
und Lautsprechern aus.
Exclusively operated with 12 V battery with negative (–) ground.
Connect the power lead (red) very last. (for non-ISO connector)
Connect the battery lead (yellow) to the positive (+) terminal of
the battery or fuse block terminal (BAT). (for non-ISO connector)
Strip about 5 mm of the lead ends for connection.
Consult a professional for installation.
Deutsch
Before Wiring/Vor der Verdrahtung/
Avant le câblage/Voor het aansluiten van de bedrading
E/TRACK
TUN
Before Installation/Vor dem Einbau/
Avant l'installation/Voor de installatie
DISP
(wenn kein ISO-Stecker verwendet wird).
Schließen Sie das Batteriekabel (gelb) an die positive (+)
Klemme der Batterie oder an die (BAT) Klemme des
Sicherungsblocks an (wenn kein ISO-Stecker verwendet wird).
Entfernen Sie etwa 5 mm der Isolierung von den Kabelenden
für den Anschluss (wenn kein ISO-Stecker verwendet wird).
Isolieren Sie alle freiliegenden Leiter.
Sichern Sie alle losen Leiter.
●Bevestigingshoek links/rechts : horizontaal
voor/achter : 0 – 30°
0 – 30°
(CQ-C1321NW)
Installation Instructions
Einbauanleitung
Instructions d’installation
Installatiehandleiding
Alimentez l’appareil absolument par la batterie de 12 V avec
sa polarité négative (–) mise à la masse.
Raccorder le fil d'alimentation (rouge) en dernier.
●Mounting space
●Einbauöffnung
●Espace nécessaire pour le montage
●Benodigde ruimte
(pour un connecteur non-ISO)
Connectez le fil (jaune) à la borne positive (+) de la batterie ou
à la borne (BAT) de la boîte à fusibles. (pour un connecteur non-ISO)
Dénudez les extrémités de fil de 5 mm environ pour la connexion.
53 mm
(pour un connecteur non-ISO)
Français
●Angle de montage latéral
: horizontal
longitudinal : 0 – 30°
Nederlands
●Montagewinkel seitlich
: horizontal
vorne-hinten : 0 – 30°
Recouvrez les fils nus d’un ruban isolant.
Resserrez les connexions de fils.
182 mm
Uitsluitend voor gebruik met een 12 V accusysteem
met negatieve (–) aarding.
Sluit de stroomdraad (rood) pas het allerlaatst aan.
4.5 mm – 6.0 mm
Remove Mounting Collar q and Trim Plate r from the main
unit temporarily, which are already mounted at shipment.
Die bei der Lieferung montierte Einbauhalterung q und
Abdeckplatte r vorübergehend vom Gerät abmontieren.
Démontez provisoirement le cadre de montage q et la
plaque de garniture r de l’appareil principal, qui sont déjà
mis en place lors de l’expédition.
Verwijder de Bevestigingskraag q en de Afwerkingsrand r,
die bij het verlaten van de fabriek gemonteerd zijn,
tijdelijk van het hoofdtoestel.
(voor een niet-ISO aansluiting)
Sluit de accudraad (geel) aan op de positieve (+) aansluiting van de
accu of van het zekeringenblok (BAT). (voor een niet-ISO aansluiting.)
Strip ongeveer 5 mm van de uiteinden van de draden om de
verbinding tot stand te kunnen brengen. (voor een niet-ISO aansluiting.)
Isoleer blote draadeinden met isolatieband.
Zet loshangende draden vast.
Supplied Hardware/Mitgelieferte Hardware/Matériel d’installation/Meegeleverde onderdelen
No.
Item
Diagram
Mounting Collar
Einbauhalterung
Cadre de montage
Bevestigingskraag
Q'ty No.
Trim Plate
Abdeckplatte
Plaque de garniture
Afwerkingsrand
1
YEFX0217263
Mounting Bolt (5 mmø)
Befestigungsschraube (5 mmø)
Boulon de fixation (5 mmø)
Bevestigingsbout (5 mmø)
Power Connector
Versorgungsstecker
Connecteur d’alimentation
Stroomstekker
Item
Diagram
1
*
TEXT
YEFC051001
Lock Cancel Plate
Verriegelungsfreigabeplatte
Plaque anti-blocage
Ontgrendelingsplaat
1
Q'ty
●Please read these instructions carefully before using this product and keep this manual for future reference.
●Bitte lesen Sie diese Bedienungsanleitung vor der Verwendung dieses Produktes aufmerksam durch und bewahren
Sie sie danach für spätere Nachschlagzwecke sorgfältig auf.
●Prière de lire ces instructions attentivement avant d’utiliser le produit et garder ce manuel pour l’utilisation ultérieure.
●Leest u deze instructie alstublieft zorgvuldig door voor u dit product in gebruik neemt en bewaar deze handleiding voor later gebruik.
2
*
Matsushita Electric Industrial Co., Ltd.
1
Web Site : http://www.panasonic.co.jp/global/
YEAJ02874
YEFM293892B NT1104-2114
* ② and ⑤ consist of a set. (YEP0FZ5700) * ② und ⑤ bestehen als Satz. (YEP0FZ5700)
* ② et ⑤ constituent un jeu. (YEP0FZ5700) * ② en ⑤ bestaan uit een set. (YEP0FZ5700)
Printed in China
Installation/Einbau/Montage/Installatie
How to install the unit/Einbau des Gerätes/Mode de montage de l’appareil/Installeren van het toestel
Caution
● Wear gloves for safety.
● Make sure that wiring is completed
before installation.
Vorsicht ● Tragen Sie Handschuhe, um sich
1
Remove the cable from the battery negative terminal.
Trennen Sie das Kabel von der negativen Batterieklemme ab.
Retirer le câble de la borne négative de la batterie.
Koppel de kabel van de negatieve aansluiting van de accu los.
2
Mounting collar q insertion
Bend mounting tabs.
Einsetzen der Einbauhalterung q
Biegen Sie die Einbaulaschen ab.
Insertion du cadre de montage q
Replier les languettes de fixation
Inbrengen bevestigingskraag q
Buig bevestigingslipjes om.
3
Connection of power connector ③
Anschluss des Versorgungssteckers ③
Raccordement du connecteur d'alimentation ③
Aansluiten van de stroomstekker ③
Main unit securing
vor Verletzungen zu schützen.
● Achten Sie vor dem Einbau darauf,
How to remove the unit/Ausbau des Gerätes/
Dépose de l’appareil/Verwijderen van het toestel
q
1
Remove the face plate.
Nehmen Sie das
Bedienteil ab.
Retirer le plaque de
façade.
Verwijder de voorplaat.
2
Remove the trim plate ④.
Entfernen Sie die
Abdeckplatte ④.
Enlevez la plaque de
garniture ④.
Verwijder de
afwerkingsrand ④.
3
Lock release
dass die Verdrahtung fertiggestellt ist.
Attention ● Porter des gants à des fins de sécurité.
● S'assurer que le câblage est terminé avant
l'installation.
Let op
● Draag handschoenen voor uw veiligheid.
● Controleer of de bedrading correct is aangelegd
voor u gaat installeren.
4
4
q
Bend appropriate tabs to secure the unit
without backlash.
Die entsprechenden Einbaulaschen so
umbiegen, dass das Gerät ohne Spielraum
fest sitzt.
Replier les languettes
de fixation appropriées
pour immobiliser
l'appareil sans
contrecoup.
Buig de juiste lipjes om
zodat het toestel vast
zit zonder speling.
w
e
q Screw the mounting bolt w into the main unit.
w Securing to the fire wall
e Snap the right and left springs into each hole.
Befestigung des
Hauptgerätes
q Schrauben Sie die Befestigungsschraube w
in das Hauptgerät.
w An der Feuerschutzwand sichern
e Lassen Sie die rechten und linken Federn in den
Löchern einschnappen.
Fixation de l'appareil
principal
q Visser le boulon de fixation w dans l'appareil
principal.
w Saisissage du pare-feu
e Bouteroller les ressorts droit et gauche dans chaque trou.
q
w
q
Vastzetten hoofdtoestel q Draai de bevestigingsbout w in het hoofdtoestel.
w Vastzetten aan het brandschot
e Zet de achterkant van het hoofdtoestel vast.
4
w
4
4
Securing to the fire wall
Befestigung an Brandschutzwand
Obtenir un pare-feu
Vastzetten aan het brandschot
Using the rear support strap (Option)
Verwendung der Einbauleiste (Option)
Utiliser de la barrette de support arrière (Option)
Gebruik van de achter-steunstrip (optioneel)
3 mm
e
Clank!
Using the rubber bushing (Option)
Verwendung der Gummibuchse (Option)
Utiliser la bague d'amortisseur en caoutchouc (Option)
Gebruik van het rubber stootkussen (optioneel)
Tapping Screw (Option)
Blechschraube (Option)
Vis taraudeuse (Option)
Zelftappende schroef
(optioneel)
Rubber Bushing (Option)
Gummibuchse (Option)
Bague en caoutchouc (Option)
Rubber stootkussen (optioneel)
Rear Support Strap (Option)
Hinterer Stützstreifen
(Option)
Barrette d'appui arrière (Option)
Steunstrip achter (optioneel)
Mounting Bolt w
Befestigungsschraube w
Boulon de fixation w Rear Support Bracket
Bevestigingsbout w (supplied with car)
Einbauleiste (vorhanden im
Fahrzeug)
Support arrière
Hexagonal nut (Option)
To the unit
(fourni avec votre voiture)
Sechskantmutter (Option) An das Gerät
Achter-steunbeugel
Ecrou hexagonal (Option)
Côté appareil
(behorend bij de auto)
Zeskantige moer (optioneel) Naar het toestel
Mounting Bolt w
Befestigungsschraube w
Boulon de fixation w
Bevestigingsbout w
To the unit
An das Gerät
Côté appareil
Naar het toestel
Snapping point
Einschnapppunkt
Position de rupture
Breekpunt
5
5
6
Trim plate ④ mounting
Anbringen der Abdeckplatte ④
Installation de la plaque de garniture ④
Bevestigen van de afwerkingsrand ④
Battery cable reconnection
Wiederanschließen des Kabels
Rebranchement du câble
Opnieuw aansluiten kabel
Caution
When this unit is installed in dashboard,
ensure that there is sufficient air flow
around the unit to prevent damage from
overheating, do not block any ventilation
holes on the unit.
Vorsicht
Bei Einbau des Geräts im Armaturenbrett
sollte darauf geachtet werden, dass der
Luftstrom um das Gerät nicht behindert ist,
um Beschädigung durch Überhitzen zu
verhindern, und die Belüftungsöffnungen
des Geräts nicht blockiert sind.
Attention
Lorsque cet appareil est installé dans le
tableau de bord, assurez-vous qu'il y a une
circulation d'air suffisante autour de
l'appareil afin d'éviter tout endommagement
provoqué par une surchauffe et qu'aucun
trou d'aération de l'appareil n'est obturé.
Let op
Wanneer dit toestel in het dashboard wordt
geïnstalleerd, moet u ervoor zorgen dat er
voldoende ventilatie is rond het toestel. Om
oververhitting te voorkomen mogen de
ventilatie-openingen in het toestel niet
afgedekt worden.
q Insert the lock cancel plate
t until you hear a click.
w Pull the main unit.
Verriegelungsfreigabe
q Setzen Sie die
Verriegelungsfreigabeplatte t
ein, bis Sie ein Klickgeräusch
vernehmen können.
w Ziehen Sie an dem Hauptgerät.
w
Libération du verrouillage
q Introduisez la plaque antiblocage t jusqu’à entendre
un clic.
w Dégager l'appareil principal.
Ontgrendeling
q Steek de
ontgrendelingsplaat t naar
binnen tot u een klik hoort.
w Trek het hoofdtoestel naar
buiten.
4
Pull out the unit with
both hands.
Ziehen Sie das Gerät mit
beiden Händen heraus.
Retirez l’appareil à deux
mains.
Trek het toestel met beide
handen naar buiten.
Wiring/Verdrahtung/Câblage/Bedrading
Caution
To prevent damage to the unit, do not connect the power connector until the whole
wiring is completed.
Vorsicht
Um Beschädigung des Gerätes zu vermeiden, schließen Sie den Versorgungsstecker
erst an, nachdem die gesamte Verdrahtung vollständig beendet wurde.
Attention
Ne pas introduire la prise d'alimentation secteur dans l'appareil tant que le câblage n'est
pas complètement terminé afin de ne pas risquer d'endommager l'appareil.
Let op
Om schade aan het toestel te voorkomen mag u de stroomstekker pas aansluiten
wanneer de bedrading volledig is aangesloten.
(L)/(L)/(G)/(L)
1
3
2
Fuse (15 A) Refer fuse replacement to your nearest authorized Panasonic
Service Centre. Do not try fuse replacement by yourself.
Sicherung (15 A) Wenden Sie sich zum Austausch der Sicherung an eine autorisierte
Panasonic-Kundendienststelle in Ihrer Nähe. Versuchen Sie nicht, den Austausch
selbst vorzunehmen.
Fusible (15 A) Confier le remplacement de fusible au centre de service de
service après-vente Panasonic agréé le plus proche. Ne pas essayer de
remplacer le fusible tout(e) seul(e).
Zekering (15 A) Laat het vervangen van de zekering over aan uw dichtstbijzijnde
Panasonic service-centrum. Probeer in geen geval zelf de zekering te vervangen.
Antenna
Antenne
Antenne
Antenne
C1 :
C3 :
(R)/(R)/(D)/(R)
External Mute Lead
To the Navi Mute lead of the Panasonic car navigation system
or car telephone mute lead.
Externe-Stummschaltungskabel
An das Navigationssystem-Stummschaltungskabel des
Panasonic Navigationssystems oder an das
Autotelefon-Stummschaltungskabel.
Fil de Mise en sourdine extérieure
A raccorder au fil Navi Mute du système de navigation automobile de
Panasonic ou au fil de mise en sourdine du téléphone pour véhicule.
Externe-geluiddempingsdraad
Naar de Navi Mute draad van een Panasonic auto-navigatiesysteem
of naar de dempingsdraad voor deautotelefoon.
(Brown w/black stripe)/(Braun mit schwarzem Streifen)/
(Brun à rayures noires)/(Bruin met zwarte streep)
External Remote Control Lead
When using a non-Panasonic external remote control,
refer to the manufacture for their product before connecting.
Leitungsdraht für externe Fernbedienung
Wenn Sie eine externe Fernbedienung verwenden, die nicht von Panasonic
hergestellt wurde, wenden Sie sich vor dem Anschluss an den Hersteller
des Produktes.
Fil de la télécommande extérieure
En cas d’utilisation d’une télécommande extérieure non-Panasonic, se
référer aux conseils du fabricant concerné pour les connexions électriques.
Externe afstandsbedieningsdraad
Bij gebruik van een externe afstandsbediening die niet van Panasonic is,
dient u voor aansluiting de handleiding of de fabrikant van het product in
kwestie te raadplegen.
Preamp Out Connector (Rear)
Vorverstärker-Ausgang (Rückseite)
Connecteur de sortie de préamplificateur (arrière)
Uitgangsaansluiting voorversterker (achter)
(Orange)/(Orange)/(Orange)/(Oranje)
A7 : (Red)/(Rot)/(Rouge)/(Rood)
Power Lead (ACC or IGN) To ACC power, +12 V DC.
Versorgungskabel (ACC oder IGN) An die ACC-Stromklemme, +12 V Gleichspannung.
Fil d’alimentation (ACC ou IGN) A l’alimentation ACC, +12 V CC.
Stroomdraad (ACC of IGN) Naar ACC stroomvoorziening, + 12 V gelijkstroom.
A5
ISO Connector
ISO-Stecker
Connecteur ISO
ISO aansluiting
ACC
A8 : (Black)/(Schwarz)/(Noir)/(Zwart)
A
A
A
A
Ground Lead To a clean, bare metallic part of the car chassis.
Massekabel An ein sauberes, metallisches Teil des Fahrzeugchassis.
Fil de mise à la masse A une partie métallique propre découverte du châssis de voiture.
Aarding Naar een schoon, bloot metalen onderdeel van het chassis.
BATTERY 15A
A
A4 : (Yellow)/(Gelb)/(Jaune)/(Geel)
Battery Lead To the car battery, continuous +12 V DC.
Batteriekabel An die Batterie des Fahrzeuges, kontinuierlich +12 V Gleichspannung.
Fil de batterie A la batterie de voiture, alimentation continue de +12 V CC.
Accudraad Naar de accu van de auto, doorlopende stroomvoorziening + 12 V gelijkstroom.
A5 : (Blue w/white stripe)/(Blau mit weißem Streifen)/(Bleu à rayures blanches)/(Blauw met witte streep)
B
Motor Antenna Relay Control Lead To Motor Antenna. (Max. 100 mA) (This lead is not intended for use with a switch actuated power antenna)
Amp·Relay Control Power Lead To Panasonic power amplifier. (Max. 100 mA) (synchronized with the power on/off of amplifier)
Steuerkabel für Relais der motorbetriebenen Antenne Zu motorbetriebenen Antenne (max. 100 mA) (Dieses Kabel dient nicht für die
Verwendung mit einer über einen Schalter aktivierten motorbetriebenen Antenne.)
Stromversorgungskabel für Verstärkerrelaissteuerung an den Panasonic Leistungsverstärker. (Max. 100 mA) (synchronisiert mit dem
Ein/Ausschalten der Stromversorgung des Verstärkers)
Fil de commande de relais d’antenne motorisée A l’antenne motorisée (100 mA maxi.) (Ce fil n’est pas conçu pour l’usage avec l’antenne
commandée par interrupteur.)
Fil d'alimentation de commande de relais d'amplificateur à amplificateur de puissance Panasonic. (Max. 100 mA)
(synchronisé à l'application ou la coupure d'alimentation de l'amplificateur)
Stuurdraad relais gemotoriseerde antenne Naar de gemotoriseerde antenne. (Max. 100 mA) (Deze draad is niet bedoeld voor een
gemotoriseerde antenne die met een schakelaar wordt ingeschakeld.)
Versterker-relais Stuurstroomdraad naar Panasonic eindversterker. (Max. 100 mA) (gesynchroniseerd met de eindversterker aan/uit)
A
B7 :
ISO Connector
ISO-Stecker
Connecteur ISO
ISO aansluiting
B5 :
B4 :
Front Right – (Gray w/black stripe)
Vorne Rechts – (Grau mit schwarzem Streifen)
Avant droit – (Gris à rayures noires)
Rechts voor – (Grijs met zwarte streep)
B1 :
B2 :
Rear Right + (Violet)
Hinten Rechts + (Violett)
Arrière droit + (Violet)
Rechts achter + (Paars)
Rear Right – (Violet w/black stripe)
Hinten Rechts – (Violett mit schwarzem Streifen)
Arrière droit – (Violet à rayures noires)
Rechts achter – (Paars met zwarte streep)
A4
IGN or ACC 12 V supply
12 V-Versorgung
(IGN/ACC)
Alimentation 12 V en
IGN ou ACC
IGN of ACC 12 V
stroomvoorziening
12 V Batteries (Continuous supply)
12 V-Batterie (Dauerversorgung)
Batterie de 12 V (alimentation continue)
12 V accu (doorlopende stroomvoorziening)
(❈)
ACC
Car-side connector
Steckverbinder am Fahrzeug
Connecteur côté voiture
Stekker aan autozijde
BATTERY 15A
(❈)
Car Type A/Kraftfahrzeug des Typs A/Type de voiture A/Autotype A
A4
A7
IGN or ACC 12 V supply
12 V-Versorgung
(IGN/ACC)
Alimentation 12 V en
IGN ou ACC
IGN of ACC 12 V
stroomvoorziening
12 V Batteries (Continuous supply)
12 V-Batterie (Dauerversorgung)
Batterie de 12 V (alimentation continue)
12 V accu (doorlopende stroomvoorziening)
●The pin arrangement of the power connector
conforms to ISO standard.
●Please check that the pin arrangement of the
connector in your car conforms to ISO standard.
●For car types A and B, change the wiring of the
red and yellow leads as shown at below.
●After connection, insulate the portions marked (❈)
with insulating tape.
Note: For cars other than types A and B, please
consult your local car shop.
-
- B2
B1 +
Connect as follows.
Nehmen Sie den Anschluss wie folgt vor.
Branchez les haut-parleurs comme suit.
Sluit de luidsprekers als volgt aan.
L
Vorsichtsmaßregeln (ISO-Stecker)
●Die Stiftbelegung des Versorgungssteckers entspricht
dem ISO-Standard.
●Bitte stellen Sie sicher, dass die Stiftbelegung
des Steckers in Ihrem Fahrzeug dem ISO-Standard
entspricht.
●Für Fahrzeuge der Typen A und B, ändern Sie die
Verdrahtung der roten und gelben Leiter gemäß Abbildung.
●Nach dem Anschluss isolieren Sie die mit (❈) markierten
Abschnitte mit Isolierband.
Hinweis: Für andere Fahrzeuge als Typ A und B,
wenden Sie sich bitte an eine örtliche Pkw-Werkstatt.
(
)
BATTERY 15A
ACC
(
)
Car Type B/Kraftfahrzeug des Typs B/Type de voiture B/Autotype B
●La disposition des broches du connecteur d'alimentation
est conforme à la norme ISO.
●Veuillez vérifier si que la disposition des broches du
connecteur d'alimentation dans votre voiture est conforme
à la norme ISO.
●Pour les types de voiture A et B, changer le câblage des
fils rouge et jaune comme indiqué ci-dessous.
●Après avoir fait les connexions, isoler les sections
marquées (❈) avec de la bande isolante.
Remarque: Pour les voitures autres que des types A et B,
veuillez consulter votre magasin de matériel automobile local.
●Use ungrounded speakers only.
Allowable input : 50 W or more
Impedance : 4 – 8 Ω
●Distance between speaker and amplifier: 30 cm or more
●Verwenden Sie nicht geerdete Lautsprecher.
Zulässige Belastbarkeit: 50 W oder mehr
Impedanz : 4 – 8 Ω
●Entfernung zwischen Lautsprecher und Verstärker: 30 cm oder mehr
●Utilisez uniquement des haut-parleurs non reliés à la masse.
Puissance d'entrée admissible: 50 W ou davantage
Impédance: 4 – 8 Ω
●Distance entre le haut-parleur et l'amplificateur: 30 cm ou davantage
R
Caution
●Do not connect more than one speaker to
one set of speaker leads. (except for connecting to
a tweeter)
Vorsicht
A4
A7
No connection
Kein Anschluss
Aucune connexion
Geen aansluiting
12 V Batteries (Continuous supply)
12 V-Batterie (Dauerversorgung)
Batterie de 12 V (alimentation continue)
12 V accu (doorlopende stroomvoorziening)
(
)
ACC
(
)
BATTERY 15A
Voorzorgen (ISO stekker)
●De pen-configuratie van de stroomstekker voldoet aan de
ISO standaard.
●Controleer of de pen-configuratie van de stekker in uw
auto eveneens voldoet aan de ISO standaard.
●Voor auto's van type A en B, dient u de bedrading voor de rode
en gele draden te wijzigen zoals hieronder staat aangegeven.
●Na het aansluiten dient u de gedeelten die met (❈)
gemarkeerd zijn met isolatieband af te plakken.
Opmerking: Voor andere auto's dan die van type A en B
dient u uw garage te raadplegen.
- B4
B3 +
Speaker Connection/Anschluss der Lautsprecher/Branchement avec les haut-parleurs/Aansluiten van de luidsprekers
●Gebruik uitsluitend ongeaarde luidsprekers.
Toegestaan ingangsvermogen: 50 W of hoger
Impedantie: 4 – 8 Ω
●Afstand tussen luidspreker en versterker: 30 cm of meer
Précautions (Connecteur ISO)
Car-side connector
Steckverbinder am Fahrzeug
Connecteur côté voiture
Stekker aan autozijde
Car-side connector
Steckverbinder am Fahrzeug
Connecteur côté voiture
Stekker aan autozijde
Precautions (ISO Connector)
- B6
B5 +
Front Left – (White w/black stripe)
Vorne Links – (Weiß mit schwarzem Streifen)
Avant gauche – (Blanc à rayures noires)
Links voor – (Wit met zwarte streep)
Front Right + (Gray)
Vorne Rechts + (Grau)
Avant droit + (Gris)
Rechts voor + (Grijs)
Power connector/Versorgungsstecker/Connecteur d’alimentation/Stroomstekker
B7 +
B6 :
B3 :
+
A7
Rear Left – (Green w/black stripe)
Hinten Links – (Grün mit schwarzem Streifen)
Arrière gauche – (Vert à rayures noires)
Links achter – (Groen met zwarte streep)
B
B
B
B
B
Front Left + (White)
Vorne Links + (Weiß)
Avant gauche + (Blanc)
Links voor + (Wit)
Standard ISO/ISO-Standard/Normes ISO/Standaard ISO
- B8
B8 :
Rear Left + (Green)
Hinten Links + (Grün)
Arrière gauche + (Vert)
Links achter + (Groen)
●Schließen Sie niemals mehr als einen Lautsprecher
an einen Satz Lautsprecherleiter an. (außer bei
Anschluss eines Hochtonlautsprechers)
Attention
●Ne raccorder pas plus d'un haut-parleur à un
ensemble de fils de haut-parleur. (Sauf lors du
raccordement à un tweeter)
Let op
●Sluit niet meer dan één luidspreker aan op één paar
luidsprekerdraden. (Behalve bij aansluiting op een
tweeter.)
●Do not use a 3-wire type speaker system
having a common earth lead.
●Verwenden Sie niemals Lautsprechersysteme mit
Dreierverkabelung, die einen gemeinsamen
Erdungsleiter aufweist.
●Ne pas utiliser pas de système de haut-parleur
de type à 3 fils ayant un fil de mise à la masse
commun.
●Gebruik geen luidsprekersysteem met drie
draden en een gedeelde aarddraad.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement