TRADITIONAL
Estimating and Installation Guide
0) estimate
Draw roof line. Measure lengths for gutter.
Step #3 select
Determine the number of parts you need.
Step €) install
Assemble on the ground, lift and attach.
Vinyl Gutter
The sensible, virtually indestructible building material.
Vinyl Gutter will not: rust, chip, dent, crush or leak. It stands
up to winter ice, snow, heating cables, salt air and desert
heat. Our vinyl Is UV protected and guaranteed not to crack,
peel or corrode. No need to paint, ever!
Worry-free Protection
Your Vinyl Gutter System is guaranteed for as long as you own your home.
To validate this warranty, please complete and mail to:
GUARANTEED FOR A LIFETIME USA. CANADA
GSW BUILDING PRODUCTS GSW BUILDING PRODUCTS
43173 Woodward Ave. 26 Lorena Street
P.O. Box 361 Barrie, Ontario
Bloomfield Hills, MI LAN 4P4
48302 Attention: Customer Service EST
Attention: Customer Service
Detach and mail after installation. м
Date Name
Address: City: State/Prov.:
Zip/Postal: Age of Home/Building (years): Telephone:
System purchased: Traditional €) Contemporary Color:
Would you participate in a survey? OQ YES {OQ NO Purchased from: Store
City: State/Prov.:
Questions? Consult your dealer or call our hotline between 8 am - 5 pm ET
1-800-461-5706
S tep O ES f IM at € This is only a guide to help you estimate your needs! All installations are different!
Begin by sketching your roofline. Note porches, additions, etc.
Measure the lengths of each gutter run.
Plan and mark downspout locations: 1 required for max. 40° of gutter.
requiring gutter.
Parts are listed below in the order required for planning.
Total length of roofline
Total number of
downspout locations.
Total length of downspout.
Gutter Parts Cost per Total Downspout Parts Gty Cost per Total
l= GUTTER DOWNSPOUT (10 lengths)
Total length of roofline divided by 10" xt each = $ | required for every drop outlet Xx each = $
HOOK
& required for each 10° gutter length XE each = $
JOINER (Two-piece) ELBOW A
1 10 connect quitter lengths/corners xt sach =$ E 3 reguired for each downspout assembly X each = $
Note: Does not fit onto drop outlets
OUTSIDE CORNER ELBOW В
90° - As needed. see * below Used to change direction along the side
for custom comers AF sach =$ of the house. Xx sach =$
INSIDE CORNER CLIP
IF - As needed. See * below for 3 required for each downspout assembly
custom corners ХФ each =$ (2 for 10' of downspout and 1 to hold
DROP OUTLET diverter extension in 'up' position) X each =$
1 required for max. 40' of quitter xt sach =$ CONNECTOR
| required to connect downspout
END CAP (Pairs) lengths over 10' x$ each =$
1 pair required to finish each gutter run Xx sach =$ DIVERTER
Note: Does not fit onto drop outlets | required at base of each downspout Xx sach =$
«fé LEAF GUARD PLUS""
7 Tetal length of roofline divided by 6' х$ each =$
DRIP EDGE * To make gutter comers other than 90°, instructions are available from
<== Total length of roofline divided by 10' х$ each = $ our Customer Service desk Please call 1 800 461 5706 between
dam — 5pm ET.
Step se Select nenecomen
DOWNSPOUT
CONNECTOR
DOWNSPOUT
ELEOW B
DOWNSPOUT
СЫР — —
ELBOW A — fg
DIVERTER
DOWNSPOUT
SPLASH BLOCK
ELBOW В
DOWNSPOUT
LEAF GUARD PLUS™
e SCREWS
JONER
END CAP
HOOK
Helpful Hints
Planning
+ Begin by sketching vour total layout.
if vou have a steel roof or live in à snow-
belt add extra hooks, e.g. one every 18”,
and install gutters lower on the fascia to
avoid being hit by snow sliding off the roof.
Fascia boards must be structurally sound to
support the gutter system filled with water.
One drop outlet is required for every 40°
of gutter. Additional downspouts increase
handling capacity.
Locate drop outlets at points that will allow
for drainage away from the foundation.
To thaw ice, heating cable approved for
vinyl can be placed in the gutters.
+
+
+
+
+
Installation
* Always work safely - never rush.
« ff foscia boards are not perpendicular
to the ground, use the Fascia Fixer
(see Accessories).
- ff parts ore difficult to snap together or
hooks do not slide freely, fubricate with
soapy water.
+ Make sure cuts are straight. Use a cutting
quide, if necessary.
« A diverter is recommended at the bottom
of each downspout to allow the extension
to swing out of the way for yard work.
+ On a straight run, put a nail or screw into
fascia at outside edge af end cap to force
gutter expansion into drop outlet.
After Installation
* If water is running down the fascia board
behind the quitter, vou may require a Drip
Edge or Leaf Guard Plus™ (see Accessories).
* Your gutters must be deaned periodically
of leaves and debris. To minimize cleaning
time, install a Leaf Guard Plus™ (see
Accessories).
+ Never use quiîters to support your weight
when dimbing on to a roof.
+ Gutters con be painted with a quality
exterior latex point. Check with a reputable
paint manufacturer.
Note: Painting is not recommended, as
the maintenance-free benefits will be fost.
Step €) Installing gutters It's easy to assemble! No special tools!
7
TY
4
N
~
|
| ||
„| | | = Level
151747
| TE
k—— 10 >
J
va
Measure 12" from end
of corner piece or end cap
Ensure the correct slope
* At the high end of the run, drive a nail
12" below the top of the fascia board.
* Snap a level” chalk line from this па!
to the opposite end of the gutter run.
» Drop the chalk line 187 for every 10 of
gutter and snap your guide” line.
Y
Work on the ground
* Slide hooks onto gutter and space
approximately 24" starting 12" from ends.
To function properly, qutters must slope
1/3" for every 10".
Install your gutter
* Use astepladder and lift each 10' section
Into place.
* Starting in the middle of each section, use
1-12" screws to fasten hooks into the fascia
along the ‘guide’ ine. The hghtweight
assembly will be supported temporarily
while you fasten the remaining hooks.
* To install joners, separate the two pieces
and place the inner piece with seals facing
down under the back lip inside the gutter.
* Press firmly to snap the inner piece
under the front hp, ensuring the seam
between gutter lengths 1s covered.
+ Place the outer cover under the gutter and
hook It over the back edge.
+ Pull the cover forward and press firmly
to snap It over the front edge.
* Attach end caps.
Y
Install drop outlet before installing the
final gutter length
* Along your ‘guide’ ine, level and screw
the drop outlet to the fascia using the two
holes on top.
* Using the temperature guide inside the
drop outlet, draw two lines above the top
of the outlet that correspond to the
temperature at the time of installation.
+ Measure from the temperature line to the
end of the last gutter section to determine
the length of the final gutter section.
* Slide gutter length into the drop outlet and
join other end to the last section installed.
No caulking required. Unique pressure-
fit gaskets guarantees a leak-proof seal.
Do | need
special tools?
No!
You need, safety glasses,
measuring tape, pencil,
level chalk line, saw,
drill set, screwdriver sel.
Joiners and end caps do not fit
onto drop outlets.
G To prevent the outer joiner from
shifting as the gutter naturaly
expands and contracts, fasten two (2)
1/2" self-tapping rust-resistant screws
through the two dimples in the top
edge of the outer joiner into the gutter.
Gutters slide within drop outlets
affowing natural expansion and
contraction.
9
Option 1. Cut a piece of gutter 6"
fong, attach an end cap and slide on a
hook. Insert the piece in the open end
of the drop outlet and screw hook to
fascia.
To end a gutter run at a drop
outlet:
Option 2. Run the last length of gutter
through the drop outlet to the end of
the run. Slide on hook(s) and an end
cap and screw hooks into fascia. Cut @
hole in the gutter directly over and no
bigger than the drop outlet opening or
perforate to form a leaf strainer.
Is Rain Master
easy to install?
Yes!
It's lightweight, has
no sharp edges and
requires no special tools.
Step €) Installing downspouts
Accessories
Begin at the top
+ Aftach an elbow to the drop outlet.
* Hold another elbow against the wall
In line with the drop outlet elbow.
* To connect the elbows, use an
Extension (see Accessories) or cut
a downspout section to suit.
* Determine the length by measuring
the gap between the elbows and
adding 2” for the overlaps.
* Secure the elbows to the
downspouts with vz" self-tapping
rust-resistant screws.
FASCIA FIXER
Provides a vertical surface
(If fascia 1s not) for gutter hooks
& drop outlets. Cam faces out.
Fasten single 2177 screw
through both parts into fascia.
ROOF RAFTER BRACKET
If no fascia exists, mount long
end of bracket to one side of
roof rafter and attach hooks
to other end.
SCREWS
#8 — 112" rust-resistant
screws. Perfect size to attach
fitings. Qty: 25/pack
Assemble your downspout lengths
+ Determine the total height of
downspout by measuring from the
wall elbow to approximately 6" above
the ground. DRIP EDGE
+ If total length 1s over 10°, downspout Extends roof edge into gutter
sections must be Joined with a tel Slip and fasten nail-hole side
tor. TUL | |
connec | under shingles. Fin should
« At the bottom of the downspout, point down into gutter.
secure an elbow with a V2” self- 11 Note: Not required if using
tapping rust-resistant screw. Leaf Guard Plus".
LEAF GUARD PLUS™
> Keeps leaves and debris out
"of gutters. Install by sliding
onto top clips of the hooks
with wide flange to fascia.
Install your downspouts
* Line up downspout assembly with
drop outlet to determine location
of downspout clips.
+ Attach 2 clips to wall for every 10°
section.
* Snap the downspout assembly into
the clips.
ELBOW B
Used to change direction
along the side of the house.
6" Approx.
|
Install your diverter Ground line EXTENSION
* Attach a diverter to the bottom elbow. For connecting elbows at
+ Attach a downspout section to the top of downspout assembly
diverter. | orto diverter.
* Add a clip to the outside of the
downspout to secure the extension CLIP-UP DIVERTER
out of the way for yard maintenance. re Directs water away from foun-
dation. Attaches to any 2" x 3°
downspout with screws provid-
ed. Lifts for easier yard work,
Ú Downspout damage usually occurs at heights under 6 Our vinyl secures with clip provided.
downspouts and Clip-Ups fit aif 2"x 3" vinyl or metal gutter systems
and resist crushing or denting. SPLASH BLOCK
Place at the end of downspout
or diverter assembly to
disperse water evenly and
prevent erosion.
Ú Elbow À is used to direct water away from the house and Elbow B is
used to change the direction along the side of the house. Look for the
arrow on the elbows to determine the flow direction.
">
