RCA RMW1636 Installation Guide
Add to my manuals23 Pages
The RCA RMW1636 is a versatile microwave with a range of features to make cooking and reheating meals a breeze. With 1100 watts of cooking power, it heats food quickly and evenly, while the 10 power levels provide precise control for delicate dishes. The spacious 1.6 cubic foot capacity can accommodate a variety of containers, and the glass turntable ensures even cooking. The RMW1636 also features a convenient digital display and easy-to-use controls, making it simple to select cooking times and power levels.
advertisement
JS1M0609-10520-005
Installation Instructions
Over the Range Microwave Oven
BEFORE YOU BEGIN
•
•
Read these instructions completely and carefully.
Save these instructions for local inspector’s use.
Observe all governing codes and ordinances.
•
Note to Installer – Be sure to leave these instructions with the Consumer.
• Note to Consumer – Keep these instructions for future reference.
• Skill level – Installation of this appliance requires basic mechanical and electrical skills.
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not covered under the Warranty.
READ CAREFULLY. KEEP THESE INSTRUCTIONS.
1
RED450E3H-P0HH0A
( P100D45AL- E3 )
廖 波
王 守 国
2009.3.5
23 1
JS1M0609-10520-005
Installation Instructions
CONTENTS
General information
Important Safety Instructions .....................3
Electrical Requirements ..............................3
Hood Exhaust ...........................................4, 5
Damage – Shipment/Installation .................6
Parts Included...............................................6
Tools You Will Need.....................................7
Mounting Space............................................7
C
Recirculating ........................................... 20–22
Attach Mounting Plate to Wall ................. 20
Preparation of Top Cabinet ..................... 20
Mount the Microwave Oven............... 21, 22
Installing the Charcoal Filter.................... 22
Before You Use Your Microwave ..............23
Step-by-step installation guide
Placement of Mounting Plate ................8–10
Removing the Mounting Plate ................... 8
Finding the Wall Studs .............................. 8
Determining Wall Plate Location ............... 9
Aligning the Wall Plate ............................ 10
Installation Types .................................11–22
A
Outside Top Exhaust .............................. 12–15
Attach Mounting Plate to Wall ................. 12
Preparation of Top Cabinet ..................... 13
Checking for Proper Damper Operation...14
Mount the Microwave Oven..................... 14
Adjust the Exhaust Adaptor..................... 15
Connecting Ductwork .............................. 15
B
Outside Back Exhaust............................. 16–19
.
Attach Mounting Plate to Wall ................. 17
Preparation of Top Cabinet ..................... 17
Outside Back Exhaust....................... 17, 18
Mount the Microwave Oven..................... 19
廖 波
王 守 国
2
维修说明书
RED450E3H-P0HH0A
( P100D45AL- E3 )
JS1M 0609-10520-005
2009.3.6
23 2
JS1M0609-10520-005
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
This product requires a three-prong grounded outlet.
The installer must perform a ground continuity check on the power outlet box before beginning the installation to insure that the outlet box is properly grounded. If not properly grounded, or if the outlet box does not meet electrical requirements noted
(under ELECTRICAL REQUIREMENTS), a qualified electrician should be employed to correct any deficiencies.
You should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded.
Where a standard two-prong wall receptacle is encountered, it is very important to have it replaced with a properly grounded three-prong wall receptacle, installed by a qualified electrician.
CAUTION: For personal safety, remove house fuse or open circuit breaker before beginning installation to avoid severe or fatal shock injury.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT,
DEFORM OR REMOVE ANY OF THE PRONGS
FROM THE POWER CORD. DO NOT USE WITH
AN EXTENSION CORD.
CAUTION: For personal safety, the mounting surface must be capable of supporting the cabinet load, in addition to the added weight of this 54 pound product, plus additional oven loads of up to 50 pounds or a total weight of 104 pounds.
CAUTION: For personal safety, this product cannot be installed in cabinet arrangements such as an island or a peninsula. It must be mounted to
BOTH a top cabinet AND a wall.
ELECTRICAL REQUIREMENTS
Product rating is 120 volts AC, 60 Hertz, 15 amps and
1.58 kilowatts. This product must be connected to a supply circuit of the proper voltage and frequency.
Wire size must conform to the requirements of the
National Electrical Code or the prevailing local code for this kilowatt rating. The power supply cord and plug should be brought to a separate 20 ampere branch circuit single grounded outlet. The outlet box should be located in the cabinet above the microwave oven. The outlet box and supply circuit should be installed by a qualified electrician and conform to the National Electrical Code or the prevailing local code.
NOTE: For easier installation and personal safety, it is recommended that two people install this product.
IMPORTANT–PLEASE READ CAREFULLY. FOR
PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED TO AVOID SEVERE OR
FATAL SHOCK.
Insure proper ground exists before use
The power cord of this appliance is equipped with a three-prong
(grounding) plug which mates with a standard three-prong (grounding) wall receptacle to minimize the possibility of electric shock hazard from this appliance.
3
维修说明书
RED450E3H-P0HH0A
( P100D45AL- E3 )
JS1M 0609-10520-005
廖 波
王 守 国
2009.3.6
23 3
JS1M0609-10520-005
Installation Instructions
HOOD EXHAUST
NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 6.
OUTSIDE TOP EXHAUST (EXAMPLE ONLY)
The following chart describes an example of one possible ductwork installation.
D U C T P I E C E S E Q U I V A L E N T
LENGTH x
NUMBER
USED =
EQUIVALENT
LENGTH
Roof Cap 24 Ft.
x (1) = 24 Ft.
12 Ft. Straight Duct (6"
Round)
12 Ft.
x (1) = 12 Ft.
Rectangular-to-Round
Transition Adaptor*
5 Ft.
Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood.
x (1) = 5 Ft.
Total Length = 41 Ft.
* IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper will have
to be cut to fit, using the tin snips, in order to allow free movement of the damper.
OUTSIDE BACK EXHAUST (EXAMPLE ONLY)
The following chart describes an example of one possible ductwork installation.
D U C T P I E C E S E Q U I V A L E N T
LENGTH* x
NUMBER
USED =
EQUIVALENT
LENGTH
Roof Cap 40 Ft.
x (1) = 40 Ft.
3 Ft. Straight Duct
(3¼" x 10"
Rectangular)
90° Elbow
3 Ft.
x (1) = 3 Ft.
10 Ft.
x (2) = 20 Ft.
Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood.
Total Length = 63 Ft.
NOTE: For back exhaust, care should be taken to align exhaust with space between studs, or wall should be prepared at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust.
4
维修说明书
RED450E3H-P0HH0A
( P100D45AL- E3 )
JS1M 0609-10520-005
廖 波
王 守 国
2009.3.6
23 4
JS1M0609-10520-005
Installation Instructions
NOTE: If you need to install ducts, note that the total duct length of 3¼" x 10" rectangular or 6" diameter round duct should not exceed 140 equivalent feet.
Outside ventilation requires a HOOD EXHAUST
DUCT. Read the following carefully.
NOTE: It is important that venting be installed using the most direct route and with as few elbows as possible. This ensures clear venting of exhaust and helps prevent blockages. Also, make sure dampers swing freely and nothing is blocking the ducts.
Exhaust connection:
The hood exhaust has been designed to mate with a standard 3¼" x 10" rectangular duct.
If a round duct is required, a rectangular-to-round transition adaptor must be used. Do not use less than a 6" diameter duct.
D U C T P I E C E S E Q U I V A L E N T
LENGTH x
Maximum duct length:
For satisfactory air movement, the total duct length of
3¼" x 10" rectangular or 6" diameter round duct should not exceed 140 equivalent feet.
Elbows, transitions, wall and roof caps, etc.,
present additional resistance to airflow and are equivalent to a section of straight duct which is longer than their actual physical size. When calculating the total duct length, add the equivalent lengths of all transitions and adaptors plus the length of all straight duct sections. The chart below shows you how to calculate total equivalent ductwork length using the approximate feet of equivalent length of some typical ducts.
NUMBER
USED =
EQUIVALENT
LENGTH
Rectangular-to-Round
Transition Adaptor* 5 Ft.
x ( ) = Ft.
Wall Cap 40 Ft.
x ( ) = Ft.
90° Elbow
45° Elbow
90° Elbow
45° Elbow
10 Ft.
5 Ft.
25 Ft.
5 Ft.
x ( ) x ( ) x ( ) x ( )
= Ft.
= Ft.
= Ft.
= Ft.
Roof Cap
Straight Duct 6" Round or
3¼" x 10" Rectangular
24 Ft.
1 Ft.
* IMPORTANT: If a rectangular-to-
round transition adaptor is used, the
bottom corners of the damper will
have to be cut to fit, using the tin x ( ) = Ft.
x ( ) = Ft.
Total Ductwork = Ft.
snips, in order to allow free movement of the damper.
Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood.
5
维修说明书
RED450E3H-P0HH0A
( P100D45AL- E3 )
JS1M 0609-10520-005
廖 波
王 守 国
2009.3.6
23 5
JS1M0609-10520-005
PARTS INCLUDED
Installation Instructions
DAMAGE – SHIPMENT/
INSTALLATION
• If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement.
• If the unit is damaged by the customer, repair or replacement is the responsibility of the customer.
• If the unit is damaged by the installer (if other than the customer), repair or replacement must be made by arrangement between customer and installer.
PARTS INCLUDED
HARDWARE PACKET
P A R T
Wood Screws
(¼" x 2")
Toggle Bolts
(and wing nuts)
( 3 / 16
" x 3")
Self-aligning
Machine Screws
(¼"-28 x 3¼")
Nylon Grommet
(for metal cabinets)
3
3
1
Q U A N T I T Y
2
P A R T
Wire-Mounting
Mounting-Plate
1
shelf
Q U A N T I T Y
2
1
exhaust adaptor
1
You will find the installation hardware contained in a packet with the unit. Check to make sure you have all these parts.
NOTE: Some extra parts are included.
ADDITIONAL PARTS
P A R T
TOP CABINET TEMPLATE
Top
Cabinet
Template
Q U A N T I T Y
1
REAR WALL TEMPLATE
Rear Wall
Template
1
Installation
Instructions
1
Separately
Packed
Grease
Filters
Charcoal
Filter
1
2
6
廖 波
王 守 国
RED450E3H-P0HH0A
( P100D45AL- E3 )
JS1M 0609-10520-005
2009.3.6
23 6
JS1M0609-10520-005
Installation Instructions
TOOLS YOU WILL NEED
Ruler or tape measure and straight edge
# 1 and #2 Phillips screwdriver Pencil
Carpenter square
(optional)
Tin snips (for cutting damper, if required)
Scissors
(to cut template, if necessary)
Electric drill with 3 and 5 / 8 " drill bits
/ 16 ", ½"
Filler blocks or scrap wood pieces, if needed for top cabinet spacing (used on recessed bottom cabinet installations only)
Gloves Saw (saber, hole or keyhole)
Stud finder or Hammer (optional)
Safety goggles Level Duct and masking tape
MOUNTING SPACE
66" or more from the floor to the top of the microwave
16-½ "
30"
2"
30"min.
Bottom edge of cabinet needs to be 30" or more from the cooking surface
Backsplash
NOTES:
• The space between the cabinets must be
30" wide and free of obstructions.
• If the space between the cabinets is greater than 30", a Filler Panel Kit may be used to fill in the gap between the microwave oven and the cabinets. Your Owner’s Manual contains the kit number for your model.
• This microwave oven is for installation over ranges up to 36" wide.
• If you are going to vent your microwave oven to the outside, see Hood Exhaust Section for exhaust duct preparation.
• When installing the microwave oven beneath smooth, flat cabinets, be careful to follow the instructions on the top cabinet template for power cord clearance.
廖 波
王 守 国
7
维修说明书
RED450E3H-P0HH0A
( P100D45AL- E3 )
JS1M 0609-10520-005
2009.3.6
23 7
JS1M0609-10520-005
Installation Instructions
1. PLACEMENT OF THE MOUNTING PLATE
A.
REMOVING THE MICROWAVE
OVEN FROM THE CARTON/
ASSEMBLE THE MOUNTING
PLATE
1.
Remove the installation instructions, filters, glass tray and the small hardware bag. Do not remove the Styrofoam protecting the front of the oven.
2.
Fold back all 4 carton flaps fully against carton sides. Then carefully roll the oven and carton over onto the top side. The oven should be resting in the Styrofoam.
B.
FINDING THE WALL STUDS
Center
Wall Studs
Carton
Styrofoam
3.
Pull the carton up and off the oven.
4.
Remove and properly discard plastic bags.
5. you will be able to assemble it take following picture.
Wire-Mounting
1.
Find the studs, using one of the following methods:
A. Stud finder–a magnetic device which locates nails.
OR
B. Use a hammer to tap lightly across the mounting surface to find a solid sound. This will indicate a stud location.
2.
After locating the stud(s), find the center by probing the wall with a small nail to find the edges of the stud. Then place a mark halfway between the edges. The center of any adjacent studs should be 16" or 24" from this mark.
3.
Draw a line down the center of the studs.
THE MICROWAVE MUST BE CONNECTED TO AT
LEAST ONE WALL STUD.
Mounting-Plate
廖 波
王 守 国
8
维修说明书
RED450E3H-P0HH0A
( P100D45AL- E3 )
JS1M 0609-10520-005
2009.3.6
23 8
JS1M0609-10520-005
Installation Instructions
C.
DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET
Plate position – beneath flat bottom cabinet Plate position – beneath framed recessed cabinet bottom
Mounting Plate Tabs
Touching the Cabinet Bottom
Mounting Plate Tabs
Touching the Back
Frame
30" to Cooktop
At least 30"
Plate position – beneath recessed bottom cabinet with front overhang
Mounting Plate with
Tabs Below Cabinet
Bottom the Same
Distance as the Front
Overhang Depth
30" to Cooktop
Your cabinets may have decorative trim that interferes with the microwave installation. Remove the decorative trim to install the microwave properly and to make it level.
THE MICROWAVE MUST BE LEVEL.
Use a level to make sure the cabinet bottom is level.
If the cabinets have a front overhang only, with no back or side frame, install the mounting plate down the same distance as the front overhang depth. This will keep the microwave level.
1.
Measure the inside depth of the front overhang.
2.
Draw a horizontal line on the back wall an equal distance below the cabinet bottom as the inside depth of the front overhang.
3.
For this type of installation with front overhang only, align the mounting tabs with this horizontal line, not touching the cabinet bottom as described in Step D.
9
廖 波
王 守 国
维修说明书
RED450E3H-P0HH0A
( P100D45AL- E3 )
JS1M 0609-10520-005
2009.3.6
23 9
JS1M0609-10520-005
Installation Instructions
D.
ALIGNING THE WALL PLATE
Hole A Centerline notches
Draw a Vertical
Line on Wall from Center of
Top Cabinet
Area E Hole C
CAUTION: Wear gloves to avoid cutting fingers on sharp edges.
1.
Draw a vertical line on the wall at the center of the
30" wide space.
2.
Use the mounting plate as the template for the rear wall. Place the mounting plate on the wall, making sure that the tabs are touching the bottom of the cabinet or the level line drawn in
Step C for cabinets with front overhang. Line up the notch and center line on the bottom of the mounting plate to the center line on the wall.
3.
While holding the mounting plate with one hand, draw circles on the wall at holes A, B, C and D
(see illustration above/actual plate marked with arrows). Four holes must be used for mounting.
Hole B
NOTE: Holes A,B and C are inside area E. If none of
A,B and c is in a stud, find a stud somewhere in area
E and draw a fo circle to line up with the stud. It is important to use at least one wood screw mounted
firmly in a stud to support the weight of the microwave. Set the mounting plate aside.
4.
Drill holes on the circles.
If there is a stud, drill a 3 /
16
" hole for wood screws.
Three holes that don’t line up with a stud, drill
8
" a hole for toggle bolts.
NOTE: DO NOT MOUNT THE PLATE AT THIS
TIME.
10
廖 波
王 守 国
维修说明书
RED450E3H-P0HH0A
( P100D45AL- E3 )
JS1M 0609-10520-005
2009.3.6
23 10
JS1M0609-10520-005
Installation Instructions
2. INSTALLATION TYPES
(Choose A, B or C)
This microwave oven is designed for adaptation to the following three types of ventilation:
A. Outside Top Exhaust (Vertical Duct)
B. Outside Back Exhaust (Horizontal Duct)
C. Recirculating (Non-Vented Ductless)
NOTE: This microwave is shipped assembled for
Recirculating.
A.
OUTSIDE TOP EXHAUST
(VERTICAL DUCT)
B.
OUTSIDE BACK EXHAUST
(HORIZONTAL DUCT)
Adaptor in Place for
Outside Top
Exhaust
See page 12
廖 波
王 守 国
See page 16
C.
RECIRCULATING
(NON-VENTED DUCTLESS)
A Charcoal Filter
Accessory Kit is required for the non-vented exhaust.
(See your Owner’s Manual for the kit number.)
See page 20
11
11
维修说明书
RED450E3H-P0HH0A
( P100D45AL- E3 )
JS1M 0609-10520-005
2009.3.6
23 11
JS1M0609-10520-005
Installation Instructions
A.
OUTSIDE TOP EXHAUST (Vertical Duct)
INSTALLATION OVERVIEW
A1. Attach Mounting Plate to Wall
A2. Prepare Top Cabinet
A3. Check Microwave Assembly
A4. Check Damper Operation
A5. Mount Microwave Oven
A6. Adjust Exhaust Adaptor
A7.
Connect Ductwork
A1.
ATTACH THE MOUNTING PLATE
TO THE WALL
To use toggle bolts:
Mounting
Plate
Spacing for Toggles More
Than Wall Thickness
Toggle Wings
Toggle
Bolt
Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud.
1.
Remove the toggle wings from the bolts.
2.
Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to ¾" onto each bolt.
Wall
Bolt End
3.
Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate.
NOTE: Before tightening toggle bolts and wood screw, make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers between the back of the mounting plate and the wall.
4.
Tighten all bolts. Pull the plate away from the wall to help tighten the bolts.
12
维修说明书
RED450E3H-P0HH0A
( P100D45AL- E3 )
JS1M 0609-10520-005
廖 波
王 守 国
2009.3.6
23 12
JS1M0609-10520-005
Installation Instructions
A2.
USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET
4.
Roll the blower unit 90° so that fan blade openings are facing out the up of the microwave.
After Rolling Before Rolling
You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor.
Back of
Microwave
Back of
Microwave
5 .
AFTER: Fan Blade
Openings Facing UP
• Read the instructions on the TOP CABINET
TEMPLATE.
• Tape it underneath the top cabinet.
• Drill the holes, following the instructions on the
TOP CABINET TEMPLATE.
CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.
A3.
ADAPTING MICROWAVE BLOWER
FOR RECIRCULATION
1.
Remove and save screw that holds blower plate to microwave.
Back of Microwave
3
Screw
Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit.
Back of
CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched.
Microwave
NOTE: The blower unit exhaust openings should match exhaust openings on rear of microwave oven.
6 .
screw from Step 1.
Blower Plate
Back of
Microwave
Blower Motor
Screw
7.
Replace the blower plate in the same position as before with the screw.
廖 波
王 守 国
13
维修说明书
RED450E3H-P0HH0A
( P100D45AL- E3 )
JS1M 0609-10520-005
2009.3.6
23 13
JS1M0609-10520-005
Installation Instructions
A5. MOUNT THE MICROWAVE OVEN
A4.
CHECK FOR PROPER DAMPER
OPERATION
Blower Plate
Exhaust Adaptor
(absent on models shipped for recirculation exhaust)
Damper
Back of
Microwave
• Place the microwave in its upright position, with the top of the unit facing up.
• This microwave oven may be shipped assembled for top exhaust (adaptor installed) or for recirculation exhaust (adaptor absent).
• Make sure tape securing damper is removed and damper pivots easily before mounting microwave.
• You will need to make adjustments to assure proper alignment with your house exhaust duct after the microwave is installed.
FOR EASIER INSTALLATION AND PERSONAL
SAFETY, WE RECOMMEND THAT TWO PEOPLE
INSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use handle during installation.
NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord.
NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf.
IMPORTANT: If filler blocks are not used, case damage may occur from over tightening screws.
NOTE: When mounting the microwave oven, thread power cord through hole in bottom of top cabinet.
Keep it tight throughout Steps 1–3. Do not pinch cord or lift oven by pulling cord.
1.
Lift microwave, tilt it forward, and hook slots at back bottom edge onto four lower tabs of mounting plate.
2.
Rotate front of oven up against cabinet bottom
3.
Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet.
廖 波
王 守 国
14
维修说明书
RED450E3H-P0HH0A
( P100D45AL- E3 )
JS1M 0609-10520-005
2009.3.6
23 14
JS1M0609-10520-005
Installation Instructions
A5.
MOUNT THE MICROWAVE OVEN
(cont.)
Cabinet Front
Cabinet Bottom Shelf
Filler Block
A6. ADJUST THE EXHAUST ADAPTOR
Open the top cabinet and adjust the exhaust adaptor to connect to the house duct.
Blower Plate
Damper
Back of
Microwave
Equivalent to
Depth of Cabinet
Recess
Self-Aligning Screw
Microwave Oven Top
4.
Attach the microwave oven to the top cabinet.
5.
Insert 2 self-aligning screws through outer top cabinet holes.
Turn two full turns on each screw.
A7.
For Front-to-Back or
Side-to-Side Adjustment,
Slide the Exhaust
Adaptor as Needed
CONNECTING DUCTWORK
House Duct
6.
Tighten center screw completely.
7.
Tighten the outer two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.)
1.
Extend the house duct down to connect to the exhaust adaptor.
2.
Seal exhaust duct joints using duct tape.
8.
Install grease filters. See the Owner’s Manual packed with the microwave.
15
廖 波
王 守 国
维修说明书
RED450E3H-P0HH0A
( P100D45AL- E3 )
JS1M 0609-10520-005
2009.3.6
23 15
JS1M0609-10520-005
Installation Instructions
B.
OUTSIDE BACK EXHAUST
(Horizontal Duct)
INSTALLATION OVERVIEW
B1. Prepare Rear Wall
B2. Attach Mounting Plate to Wall
B3. Prepare Top Cabinet
B4. Adjust Blower
B5. Mount the Microwave Oven
B1.
PREPARING THE REAR WALL
FOR OUTSIDE BACK EXHAUST
You need to cut an opening in the rear wall for outside exhaust.
• Read the instructions on the REAR WALL
TEMPLATE.
• Tape it to the rear wall, lining up with the holes previously drilled for holes A and B in the wall plate.
• Cut the opening, following the instructions of the
REAR WALL TEMPLATE.
16
廖 波
王 守 国
维修说明书
RED450E3H-P0HH0A
( P100D45AL- E3 )
JS1M 0609-10520-005
2009.3.6
23 16
JS1M0609-10520-005
Installation Instructions
B2.
ATTACH THE MOUNTING PLATE B3.
USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET
You need to drill holes for the top support screws and a hole large enough for the power cord to fit through.
Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud.
1.
Remove the toggle wings from the bolts.
2.
Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to ¾ " onto each bolt.
To use toggle bolts:
Mounting
Plate
Spacing for Toggles More
Than Wall Thickness
Toggle Wings
Toggle
Bolt
• Read the instructions on the TOP CABINET
TEMPLATE.
• Tape it underneath the top cabinet.
• Drill the holes, following the instructions on the
TOP CABINET TEMPLATE.
CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.
B4.
ADAPTING MICROWAVE BLOWER
FOR OUTSIDE BACK EXHAUST
1.
Remove and save screw that holds blower motor to microwave,Lift up the blower plate.
screw
Blower Motor
Back of
Microwave
Wall
Bolt End
3.
Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate.
NOTE: Before tightening toggle bolts and wood screw, make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers between the back of the mounting plate and the wall.
4.
Tighten all bolts. Pull the plate away from the wall to help tighten the bolts.
Blower Motor
Screw
2.
Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit.
BEFORE: Fan Blade
Openings Facing Front
17
廖 波
王 守 国
维修说明书
RED450E3H-P0HH0A
( P100D45AL- E3 )
JS1M 0609-10520-005
2009.3.6
23 17
JS1M0609-10520-005
B4
Installation Instructions
ADAPTING MICROWAVE BLOWER
FOR OUTSIDE BACK EXHAUST
(cont.)
3.
Remove “Parts A”with Nipper or Scissors.
5.
Place the blower unit back into the opening.
End A
End B
4.
Before Rotation
Back of
Microwave
Part”A”
Rotate blower unit counterclockwise 180°.
After Rotation
Back of
Microwave
CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched.
NOTE: The blower unit exhaust openings should match exhaust openings on rear of microwave oven.
6.
Secure the blower unit to the microwave with the screw from Step 1.
Blower Plate
Back of
Microwave
Blower Motor
Screw
7.
Replace the blower plate in the same position as before with the screw.
8.
Attach the exhaust adaptor to the rear of the oven by sliding it into the guides at the top center of the back of the oven.
Adaptor
Back of
Microwave
Guide
Guide
Locking Tabs
Push in securely until it is in the lower locking tabs.
Take care to assure that the damper hinge is installed so that it is at the top and that the damper swings freely.
廖 波
王 守 国
18
维修说明书
RED450E3H-P0HH0A
( P100D45AL- E3 )
JS1M 0609-10520-005
2009.3.6
23 18
JS1M0609-10520-005
Installation Instructions
B5.
MOUNT THE MICROWAVE OVEN
Cabinet Front
Cabinet Bottom Shelf
Filler Block
Equivalent to
Depth of Cabinet
Recess
FOR EASIER INSTALLATION AND PERSONAL
SAFETY, WE RECOMMEND THAT TWO PEOPLE
INSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use handle during installation.
NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord.
NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf.
IMPORTANT: If filler blocks are not used, case damage may occur from over tightening screws.
NOTE: When mounting the microwave oven, thread power cord through hole in bottom of top cabinet.
Keep it tight throughout Steps 1–3. Do not pinch cord or lift oven by pulling cord.
1.
Lift microwave, tilt it forward, and hook slots at back bottom edge onto four lower tabs of mounting plate.
Self-Aligning Screw
Microwave Oven Top
4.
Attach the microwave oven to the top cabinet.
5.
Insert 2 self-aligning screws through outer top cabinet holes.
Turn two full turns on each screw.
6.
Tighten center screw completely.
7.
Tighten the outer two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.)
2.
Rotate front of oven up against cabinet bottom
3.
Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet.
8.
Install grease filters. See the Owner’s Manual packed with the microwave.
廖 波
王 守 国
19
维修说明书
RED450E3H-P0HH0A
( P100D45AL- E3 )
JS1M 0609-10520-005
2009.3.6
23 19
JS1M0609-10520-005
Installation Instructions
C.
RECIRCULATING
(Non-Vented Ductless)
INSTALLATION OVERVIEW
C1. Attach Mounting Plate to Wall
C2. Prepare Top Cabinet
C3. Mount the Microwave Oven
C4. Install Charcoal Filter
C1.
ATTACH THE MOUNTING PLATE
TO THE WALL
Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud.
1.
Remove the toggle wings from the bolts.
2.
Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to ¾ " onto each bolt.
To use toggle bolts:
Mounting
Plate
Spacing for Toggles More
Than Wall Thickness
Toggle Wings
Toggle
Bolt
Wall
Bolt End
3.
Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate.
NOTE: Before tightening toggle bolts and wood screw, make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers between the back of the mounting plate and the wall.
4.
Tighten all bolts. Pull the plate away from the wall to help tighten the bolts.
C2.
USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET
You need to drill holes for the top support screws and a hole large enough for the power cord to fit through.
• Read the instructions on the TOP CABINET
TEMPLATE.
• Tape it underneath the top cabinet.
• Drill the holes, following the instructions on the
TOP CABINET TEMPLATE.
CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.
20
廖 波
王 守 国
维修说明书
RED450E3H-P0HH0A
( P100D45AL- E3 )
JS1M 0609-10520-005
2009.3.6
23 20
JS1M0609-10520-005
Installation Instructions
C3.
MOUNT THE MICROWAVE OVEN NOTE: When mounting the microwave oven, thread power cord through hole in bottom of top cabinet.
Keep it tight throughout Steps 1–3. Do not pinch cord or lift oven by pulling cord.
1.
Lift microwave, tilt it forward, and hook slots at back bottom edge onto four lower tabs of mounting plate.
FOR EASIER INSTALLATION AND PERSONAL
SAFETY, WE RECOMMEND THAT TWO PEOPLE
INSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use handle during installation.
NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord.
NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf.
IMPORTANT: If filler blocks are not used, case damage may occur from over tightening screws.
2.
Rotate front of oven up against cabinet bottom
3.
Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet.
Cabinet Front
Cabinet Bottom Shelf
Filler Block
Equivalent to
Depth of
Cabinet Recess
Self-Aligning Screw
Microwave Oven Top
4.
Attach the microwave oven to the top cabinet.
廖 波
王 守 国
21
维修说明书
RED450E3H-P0HH0A
( P100D45AL- E3 )
JS1M 0609-10520-005
2009.3.6
23 21
JS1M0609-10520-005
Installation Instructions
C3 MOUNT THE MICROWAVE OVEN
(cont.)
5.
Insert 2 self-aligning screws through outer top cabinet holes.
Turn two full turns on each screw.
C4.
INSTALLING THE CHARCOAL
FILTER
1.
Remove screws on top of grille using a #1 Phillips screwdriver.
2.
Open the door.
3.
Remove the grille.
• Pull the grille straight off.
Charcoal
Filter
6.
Tighten center screw completely.
7.
Tighten the outer two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.)
4.
Install the charcoal filter. When properly installed, the wire mesh of the filter should be visible from the front.
5.
Replace the grille and the screws.
6.
Close the door.
MO14XX Series Models MO16XX Series Models
8.
Install grease filters. See the Owner’s Manual packed with the microwave.
Insert mesh-side down Insert mesh-side up
廖 波
王 守 国
22
维修说明书
RED450E3H-P0HH0A
( P100D45AL- E3 )
JS1M 0609-10520-005
2009.3.6
23 22
JS1M0609-10520-005
Installation Instructions
BEFORE YOU USE YOUR MICROWAVE
1.
Make sure the microwave oven has been installed according to instructions.
6.
Read the Owner’s Manual.
2.
Remove all packing material from the microwave oven.
3.
Install turntable and ring in cavity.
4.
Replace house fuse or turn breaker back on.
7.
KEEP INSTALLATION INSTRUCTIONS FOR
THE LOCAL INSPECTOR’S USE.
5.
Plug power cord into a dedicated 20 amp electrical outlet.
Insure proper ground exists before use
23
廖 波
王 守 国
维修说明书
RED450E3H-P0HH0A
( P100D45AL- E3 )
JS1M 0609-10520-005
2009.3.6
23 23
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project