Lenco SCR-97 MP3 Kids portable stereo fm radio Instruction manual
Below you will find brief information for portable stereo fm radio SCR-97 MP3 Kids. The SCR-97 MP3 Kids is a compact and versatile device that allows you to enjoy music from various sources, including CDs, MP3s, cassette tapes, and FM radio. It features a digital display, a telescopic antenna, and a built-in speaker for convenient listening. The device can be powered by AC adapter or batteries for portability.
Advertisement
Advertisement
PORTABLE STEREO FM RADIO WITH
CD/MP3-PLAYER AND CASSETTE
SCR-97 MP3 Kids
INSTRUCTION MANUAL
For information and support, www.lenco.eu
WARNING
CLASS 1 LASER PRODUCT
CLASS 1 LASER PRODUCT
APPAREIL Á LASER DE CLASSE 1
PRODUCTO LASER DE CLASE 1
This product contains a low power laser device.
CAUTION
INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCKS
DEFEATED.
AVOID EXPOSURE TO BEAM
Warning: Do not touch the lens.
DO NOT THROW BATTERIES IN FIRE !
PRECAUTIONS
Follow the advice below for safe and appropriate operations.
ON PLACEMENT
• Do not use the unit in places which are extremely hot, cold, dusty, or humid.
• Place the unit on a flat and even surface.
• Do not restrict the air flow of the unit by placing it in a place with poor air flow, by covering it with a cloth, or by placing it on a carpet.
ON SAFETY
• When connecting and disconnecting the AC cord, grip the plug and not the cord itself. Pulling the cord may damage it and create hazard.
• When you are not going to use the unit for a long period of time, disconnect the AC power cord.
ON AC VOLTAGE
• Before use, check that the rated voltage of your unit matches your local voltage.
ON CONDENSATION
• When left in a heated room where it is warm and damp, water droplets or condensation may form inside the CD player.
• When there is condensation inside the unit, the unit may not function normally.
• Let it stand for 1 to 2 hours before turning the power on, or gradually heat the room up and dry the unit before use.
* Ensure a minimum distance of 5 cm around the apparatus for sufficient ventilation.
* Ensure that the ventilation is not impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc..
* Do not place naked flame sources, such as lighted candles on the apparatus.
* Take attention to the environmental aspects of battery disposal.
* Use the apparatus only in moderate climates.
* Do not expose the apparatus to dripping or splashing.
* Do not place objects filled with liquids, such as vases, on the apparatus.
• Mains plug is used as the disconnect device. It shall remain readily operable and should not be obstructed during intended use. To be completely disconnected the apparatus from supply mains, the mains plug of the apparatus shall be disconnected from the mains socket outlet completely.
Should any trouble occur, disconnect the AC power cord and refer servicing to qualified personnel.
The lightening flash with arrowhead symbol within the triangle is a warning sign alerting the user of "dangerous voltage" inside the unit.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION : To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside the unit. Refer all servicing to qualified personnel.
The exclamation point within the triangle is a warning sign alerting the user of important instructions accompanying the product.
In case of malfunction due to electrostatic discharge, the apparatus has to be reset by disconnecting it from mains supply.
THE MARKING PLATE IS LOCATED AT THE BACK OF ENCLOSURE OF THE APPARATUS.
LOCATION OF CONTROLS
1. VOLUME CONTROL
2. FUNCTION SWITCH
3. CARRYING HANDLE
4. CASSETTE PAUSE
5. CASSETTE STOP/EJECT
6. CASSETTE F.FWD
7. CD OPEN BUTTON
8. CD DOOR
9. CASSETTE REWIND
10. CASSETTE PLAY
11. CASSETTE RECORD
12. FM STEREO
13. DIAL SCALE
14. MODE SWITCH
15. CD DISPLAY
16. TUNING CONTROL
17. SPEAKER
18. CD NEXT BUTTON
19. PLAY/PAUSE BUTTON
20. CD BACK BUTTON
21. CASSETTE DOOR
22. CD PROG/CLK-ADJ./
PLAY MODE BUTTON
23. CD STOP BUTTON
24. POWER BUTTON
25. PHONES JACK
26. TELESCOPIC ANTENNA
27. BATTERY COMPARTMENT
28. AC SOCKET
POWER SUPPLY
USING HOUSE CURRENT
Before use, check that the rated voltage of your unit matches your local voltage.
Note: Plug is used as the disconnect device.
The disconnect device shall remain readily operable.
USING BATTERIES
Disconnect the AC power cord from the AC inlet of the unit. Battery power is cut automatically by the cord while it is connected.
To AC socket
To AC outlet
When the volume decrease, or the sound distorts, replace all of the batteries with new ones.
battery door
GB 1
Insert eight UM-2 ( size C ) batteries.
TURN ON / OFF THE SYSTEM
Press the POWER button to turn the audio on.
To change the audio mode between CD, RADIO and TAPE , set the FUNCTION switch while the power is on.
The audio mode is displayed.
Turn off the unit by pressing the POWER button.
The current time is shown on the display.
POWER
ADJUSTING THE SOUND
TO ADJUST THE VOLUME
WHEN RECORDING
The VOLUME control may be adjusted with no effect on the recorded signal.
FOR PRIVATE LISTENING
Plug in headphones (ø3.5 mm stereo mini-plug) to the
PHONES jack.
When headphones are plugged in, the speakers are automatically disconnected.
MIN. MAX.
VOLUME
CLOCK ADJUSTMENT
on LCD display at standby mode.
1. Press the PROGRAM / CLOCK-ADJ. button,
2. Press the NEXT or BACK to select 12 hours or 24 hours display.
3. Press the PROGRAM / CLOCK-ADJ. button, the hour digit flash.
the hour digit flash.
4. Press the NEXT or BACK to adjust hour digit.
5. Press the PROGRAM / CLOCK-ADJ. button, the minute digit flash.
6. Press the NEXT or BACK to adjust minute digit.
7. Press the PROGRAM / CLOCK-ADJ. button again, the correct time is shown on display.
LCD display
CLOCK-ADJ.
LISTENING TO THE RADIO
1 . Turn on the unit by pressing the POWER button.
3 . Select a MODE.
MODE
FM ST. FM MONO
POWER
2 . Set to RADIO
FUNCTION
RADIO
CD display
4 . Tune in to a station.
TUNING
5 . Adjust the sound.
FOR BETTER RECEPTION
FM
MIN. MAX.
VOLUME
NOTE :
1. FM stereo LED indicator lights if receive FM stereo broardcast and the MODE switch
set on "FM STEREO".
2. When too much noise is heard during FM STEREO reception, set MODE switch to FM mono.
AFTER LISTENING
Turn off the unit by pressing the POWER button.
Unit will be automatically off after 4.5 hours without further operation.
GB 2
COMPACT DISC PLAYBACK
1 . Turn on the unit by pressing the
POWER button.
POWER
2 . Set to CD
FUNCTION
CD
6. Press the PLAY/PAUSE button.
Track number "01" & the symbol " " & "CD" will be shown during normal compact disc playback.
Track number "001", the symbol " " & "MP3" will be shown during MP3 playback.
Track number "001", the symbol " " & "WMA " will be shown during WMA playback.
3 . Open the disc holder by pushing the CD door open button.
CD display WMA display
4. Insert a disc with the label side facing up.
5 . Close the disc holder.
The disc will rotate and the total tracks of the disc
will show on the display.
MP3 display
TO INTERRUPT PLAYBACK
Press the Play/Pause button and the symbol " " will be flashed. Press the button again to resume playback.
PLAY/PAUSE
TO STOP PLAYBACK
Press the STOP button and the display shows the total tracks of the disc.
CD display WMA display
MP3 display
•
•
•
TO SKIP TO THE BEGINNING OF A TRACK
• Press either one of the skip buttons according to the desired skip direction.
Play/back resumes from the selected track.
When the button is pressed once during play, the previous track starts again.
When the button is pressed once during play, the next track plays.
SEARCHING FOR A PASSAGE WITHIN A TRACK
• Keep the or button pressed during playback, and release the button as soon as you recognise the desired passage. Then normal CD playback will resume from this point.
Unit will be automatically off after 30mins without any operation (in stop mode / CD door open).
CD display
REPEAT , REPEAT FOLDER , REPEAT ALL AND MIX PLAYBACK
Press PLAY MODE button during CD playback.
CD plays with a single track repeat, all tracks repeat or randomly.
PLAY MODE
GB 3
FOR NORMAL COMPACT DISC PLAYBACK
Mode sequence REPEAT >> REPEAT ALL >> MIX >>
CLEAR.
FOR MP3 / WMA PLAYBACK
Mode sequence REPEAT >> REPEAT FOLDER >>
REPEAT ALL >> MIX >> CLEAR.
During Repeat 1 mode, display shows During Repeat 1 mode, display shows
During Repeat 2 mode, display shows
During Mix mode, display shows
During Repeat 2 mode, display shows
During Repeat 3 mode, display shows
CD display
During Mix mode, display shows
Note on CD-R/RW discs
- Because of non-standardized format definition/ production of CD-R/RW,
MP3 / WMA display
playback quality and performance are not guaranteed.
- Manufacturer is not responsible for the playability of CD-R/RW due to recording conditions, such as PC performance,
writing software, media ability, etc.
- Do not attach a seal or label to either side of the CD-R/RW disc. It may cause a malfunction.
- It is recommended to record only audio files on CD-R/RW discs for easy reading.
PROGRAMMED PLAYBACK
PROGRAMMED PLAYBACK
FOR NORMAL COMPACT DISC PLAYBACK
Programmed playback enables tracks on a disc to be played in the desired order. Up to 20 tracks can be programmed.
1. Press the " PROGRAM " button.
2. Press the " NEXT " and " BACK " buttons to select the desired track number.
3. Press the " PROGRAM " button again to memorize the track.
4. Repeat steps 2 and 3 until all desired tracks are programmed.
5. Press the " PLAY/PAUSE " button to start.
" " , " PROG " & track number are shown on the
CD display.
6. Press the " STOP " button once to stop programmed playback.
7. Press the " PLAY/PAUSE " button to resume programmed playback.
8. Open the CD door, turn off the CD player or press the
" STOP " button twice to clear the programmed memory.
Note : Programming can only be made when the player
is in stop mode.
FOR MP3 / WMA PLAYBACK
Programmed playback enables folders/albums or tracks on a disc to be played in the desired order. Up to 20 folders/albums or tracks can be programmed.
1. Press the " PROGRAM " button.
2. Press the " NEXT " and " BACK " buttons to select the desired track number.
3. Repeat steps 2 and 3 until all desired folders or tracks are programmed.
4. Press the " PLAY/PAUSE " button to start.
" ", " PROG " and " MP3 / WMA " & track number are shown on the CD display.
5. Press the " STOP " button once to stop programmed playback.
6. Press the " PLAY/PAUSE " button to resume programmed playback.
7. Open the CD door, turn off the CD player or press the
" STOP " button twice to clear the programmed memory.
Note : Programming can only be made when the player
is in stop mode.
MP3 / WMA display
" PROGRAM "
CD display
" PROGRAM "
GB 4
TAPE PLAYBACK
1 . Set to TAPE FUNCTION
TAPE
3 . Press the PLAY button.
PLAY
2 . Insert the cassette.
TO STOP PLAYBACK
Press the STOP / EJECT button.
TO INTERRUPT PLAYBACK
Press the PAUSE button.
To resume play, press the PAUSE button again.
TO FAST WIND
Press the REWIND or F.FWD button. Press the STOP/EJECT button to stop winding at the desired position.
RECORDING
USE ONLY NORMAL ( TYPE I ) TAPE FOR RECORDING.
1 . Insert the cassette tape.
4 . Prepare to play the source to be recorded and play it.
Recording from a CD Recording from the radio
FUNCTION
CD
FUNCTION
RADIO
2 . Press the PAUSE button.
PAUSE PLAY THE CD TUNE INTO A STATION
5 . Press the PAUSE button.
PAUSE
3 . Press the RECORD button.
RECORD
TO STOP RECORDING
Press the STOP / EJECT button.
TO INTERRUPT RECORDING
Press the PAUSE button.
To resume recording, press the PAUSE button again.
TO ERASE A RECORDED TAPE
1. Set the FUNCTION selector to TAPE.
2. Insert a tape with the side you want to erase facing you.
3. Press the RECORD button to start erasing.
Unit will be automatically off after 4.5 hours without further operation.
MAINTENANCE
CLEANING CD
If the CD skips or will not play , the disc may need cleaning. Before playing, wipe the disc from the centre out with a cleaning cloth. After playing, store the disc in its case.
CLEANING THE TAPE HEADS
To maintain optimum sound quality, clean the playback/ record heads ( a ) ,erasure head (b), pinch rollers (c), and capstans (d) regularly (every 10 hours of use ). Use a cotton swab lightly moistened with cleaning fluid or denatured alcohol.
c d a b
CLEANING THE CD LENS
If the CD lens is dusty, clean it with a brush-blower. Blow several times on the lens and remove the dust with the brush. Finger prints may be removed with a cotton swab moistened with alcohol.
CLEANING THE UNIT
Do not use volatile chemicals on this unit. Clean by lightly wiping with a soft cloth.
IMPORTANT NOTE
If an abnormal display indication or an operating problem occurs, disconnect the AC power cord and remove the batteries. Wait at least 5 seconds, then reconnect the AC power cord or reinstall the batteries.
WARNING
Should the CD door be opened before the reading of the CD completed, a jamming noise may occur. This is resolved by closing the CD door.
GB 5
SPECIFICATIONS
CASSETTE SECTION
Track format:
Recording system:
Erasing system:
Tape speed:
F.F. & REW time:
Frequency response:
CD SECTION
Channels:
S / N ratio:
Wow & Flutter:
Sampling frequency:
Quantization:
Pick up light source:
Pick up wave length
2 track stereo
AC bias
Magnetic erase 6 poles
4.75 cm / sec.
170 sec. (F-60 tapes)
125 Hz - 8000 Hz (Normal tape)
2 channels
60 dB undetectable
44.1 kHz 8 x over sampling
1 bit DA converter
Semi - conductor laser
790 mm
RADIO SECTION
Tuning ranges:
Antennas:
FM 87.5 - 108 MHz
FM Rod antenna
GENERAL
Output power:
Power consumption:
Speaker:
Phones jack:
Power source:
Dimensions:
Weight
1.2W + 1.2W (RMS)
13W
3" 8 OHM
3.5MM
AC : 230V~50Hz
DC : 12V ( 8 x 1.5V LR14/"C"/UM2 )
288(L) x 238(D) x 155(H)mm
2.2 KGS
Due to continuing improvement, the features and the design are subject to change without notice.
Where to place the item :
Today’s furniture is coated with a wide variety of lacquers and synthetic-coatings that are treated with an extensive range of cleaning products.
Therefore, the possibility that some of these substances contain components that react adversely to the rubber feet of the item and soften them, cannot be completely excluded. The rubber feet of the appliance can cause discoloring to furniture surfaces. If necessary, place the appliance on a non-slide surface.
Service and support
For information: www.lenco.com
For support: http://lencosupport.zendesk.com
Lenco helpdesk:
Germany
The Netherlands
Belgium
France
0900-1520530
0900-23553626
02-6200115
03-81484280
(Local charges)
(Local charges + 1ct p/min)
(Local charges)
(Local charges)
The helpdesk is accessible from Monday till Friday from 9 AM till 6 PM.
When contacting Lenco, you will always be asked for the model and serial number of your product. The serial number can be found on the back of the device. Please write down the serial number below:
Model: SCR-97 MP3 Kids
Serial number: _________________________________
Lenco offers service and warranty in accordance to European law, which means that in case of repairs (both during and after the warranty period) you should contact your local dealer.
Important note: It is not possible to send products that need repairs to Lenco directly.
Important note:
If this unit is opened or accessed by a non-official service center in any way, the warranty expires.
This device is not suitable for professional use. In case of professional use, all warranty obligations of the manufacturer will be voided.
If at any time in the future you should need to dispose of this product please note that: Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice. (Waste Electrical and Electronic Equipment Directive)
GB 6

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- CD, MP3, cassette, and FM radio playback
- Digital display for track information
- Telescopic antenna for better FM reception
- Built-in speaker for convenient listening
- Programmable playback for CDs and MP3s
- Recording from CD or radio to cassette
- Clock display and adjustment
- Headphone jack for private listening
- AC adapter and battery power options