KitchenAid | KTTS505EBL | Use and Care Manual | KitchenAid KTTS505EBL Use and Care Manual

INTEGRATED COMPACTOR
Use & Care Guide
For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230 or visit our website at
www.kitchenaid.com
In Canada, for assistance, installation or service, call: 1-800-807-6777 or visit our website at www.KitchenAid.ca
Table of Contents ............................................................................................................2
W10242569B
TABLE OF CONTENTS
COMPACTOR SAFETY ..................................................................2
INSTALLATION INSTRUCTIONS ..................................................3
Unpacking ....................................................................................3
Location Requirements ................................................................4
Electrical Requirements ...............................................................4
Undercounter Installation.............................................................5
COMPACTOR USE.........................................................................7
How Your Compactor Works.......................................................7
Loading.........................................................................................7
WHISPER QUIET® Plus System...................................................7
Starting the Compactor ...............................................................7
Using Solid (Locked) Cycle ..........................................................7
Using the Air Filter or Freshener ..................................................8
Removing a Filled Bag .................................................................8
Installing a New Bag.....................................................................8
COMPACTOR CARE ......................................................................9
Changing the Air Filter or Freshener ............................................9
Cleaning........................................................................................9
TROUBLESHOOTING ..................................................................10
ASSISTANCE OR SERVICE .........................................................11
In the U.S.A. ...............................................................................11
In Canada ...................................................................................11
Accessories ................................................................................11
WARRANTY ..................................................................................12
COMPACTOR SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
DANGER
WARNING
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.
2
IMPORTANT SAFETY INSTRUCTIONS
WARNING: When using an electrical appliance, basic precautions should always be followed, including the following:
■
■
■
■
■
Read all instructions before using the compactor.
Close supervision is necessary when used by or near
children. Do not allow to be used as a toy, or to run
unattended at any time. Lock Key Switch when not in use
and store key out of reach of children.
Do not touch moving parts.
■
Do not operate with a damaged cord set, plug, motor, or
after damage in any manner. Have the compactor
examined, repaired or adjusted by an authorized
serviceperson.
Use only for intended use as described in this manual. Do
not use other than manufacturer's recommended
attachments.
■
■
■
Do not compact toxic or volatile flammable material such as
oily rags and insect sprays. Do not compact lighted
cigarettes, cigars, or other hot or burning items. Do not
overload the compactor.
Do not take apart the compactor. Incorrect reassembly can
cause electric shock when subsequently used.
Handle a loaded trash bag with care. Sharp objects can
pierce the bag and cause injury. Do not overload trash bag
with heavy material such as glass.
This compactor is intended for household use only.
SAVE THESE INSTRUCTIONS
INSTALLATION INSTRUCTIONS
Installer: Leave Use and Care Guide with the homeowner.
Homeowner: Keep Use and Care Guide for future reference and
for local electrical inspector’s use, if required.
Unpacking
WARNING
Excessive Weight Hazard
Use two or more people to move and install compactor.
Failure to do so can result in back or other injury.
IMPORTANT:
■ Do not grasp console to move compactor.
■
6. Place the 2 corner posts from the carton on the floor near the
compactor.
7. Open the compactor drawer and remove any shipping
materials or other items from the drawer.
NOTE: Do not remove the compactor bag.
8. Grasp the handle and raise the front of drawer until it clears
the drawer stops.
9. Grasp sides of drawer and lift drawer out of compactor.
10. Place the drawer on the 2 corner posts.
Begin in the room where the compactor will be located.
1. Remove compactor from shipping carton.
2. Remove all packaging materials such as tape and shipping
pads.
3. Use a mild detergent and warm water to remove waxy
residue caused by shipping material.
4. Dry thoroughly with a soft cloth. For more information, see
“Cleaning.”
5. Be sure the power cord is attached to the cord clip on the
rear of the compactor.
A
11. Place the other 2 corner posts on the floor to the side of the
compactor.
12. Grasp the sides of the compactor cabinet and put compactor
on its side on top of the corner posts.
A. Cord clip
3
13. Remove the shipping base from the bottom of the compactor.
Clearance Dimensions
A
B
A. Leveling legs
B. Shipping base
Location Requirements
Product Dimensions
B
A
A. Leave 6" (15.2 cm) of clearance space to the right side of the
compactor in order to remove the compactor bags.
B. Leave 23" (58.4 cm) of clearance in front of the compactor in
order to fully open or remove the compactor drawer.
Electrical Requirements
34¹⁄₈"
(86.7 cm)
WARNING
15"
(38.1 cm)
24"
(61 cm)
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Cutout Dimensions
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Recommended Grounding Method
3" min.
(7.6 cm)
A
34¹⁄₄" min.
(87 cm)
24" min.
(61 cm)
18" min.
(45.7 cm)
15¹⁄₄" min.
(38.7 cm)
A. Grounded eletrical outlet must be a minimum of 3" (7.6 cm) away
from surrounding cabinets or nearby walls as shown. It can be
placed either to the left or the right side of the compactor.
4
This compactor is for use on a single phase, 115-volt, 60 Hz, AC
only, 15- or 20-amp fused and properly grounded circuit and is
equipped with a grounding plug as shown below. It is
recommended that a separate circuit serving only this appliance
be provided.
This compactor must be grounded while in use to reduce the risk
of electric shock. The compactor is equipped with a threeconductor cord and 3 prong grounding-type plug to fit the proper
grounding-type receptacle. The green (or green and yellow)
conductor in the cord is the grounding wire.
NOTE: Do not connect the green (or green and yellow) wire to a
live terminal.
Undercounter Installation
NOTE: Proper installation is your responsibility. Make sure you
have everything necessary for correct installation. It is the
personal responsibility and obligation of the customer to contact
a qualified installer to assure that electrical installation meets all
National and Local codes and ordinances.
Tools Needed
Gather the required tools and parts before starting installation.
■
■
■
■
Level
Tape measure
Pliers
Scissors
Phillips screwdriver
Flat-blade screwdriver
⁵⁄₁₆" box-end wrench
Utility knife
■
■
■
■
IMPORTANT:
■ Do not grasp control panel to move compactor.
■
Slide compactor onto cardboard or hardboard before moving
compactor across floor to avoid floor covering damage.
■
Do not allow the rear frame of the compactor to touch the
floor covering when lifting or moving compactor.
2. Use pliers to lower the leveling legs away from the cabinet.
Adjust the legs so there will be a ¹⁄₈" (3 mm) to ¹₄" (6.4 mm)
space between the top of the compactor and the top of the
cabinet opening. Stand the compactor upright.
3. For model with cabinet, remove the plastic plugs from the
compactor cabinet top.
4. Move the compactor close to its final position.
5. Plug into a grounded 3 prong outlet.
6. Determine if you want the compactor frame or drawer front
flush with the cabinet front.
Using the two #8-18 x ⁵₁₆" screws, install the retaining
brackets to cabinet top as needed:
■
If the compactor frame is to be flush with the cabinet
front, place retaining bracket screws through “1.”
■
If the compactor drawer front is to be flush with the
cabinet front, place retaining bracket screws through “3.”
■
If the compactor is to be midway between “1” and “3,”
place the retaining bracket screws through “2.”
A
B
Undercounter Installation
NOTE: Installation hardware is not provided with full cabinet
models.
1. Measure the height of your cabinet opening. The top of the
compactor should be at least ¹₈" (3 mm) from the top of the
cabinet opening.
The rear wheels are preset for a cabinet opening height of
34¹⁄₄" (87 cm) (Position 1).
3 2
1
To adjust for other cabinet opening heights:
■
Loosen self-tapping screw just enough to clear stud from
hole in position 1.
■
Move the rear wheel and stud to position 2 or 3 as
needed for your cabinet opening measurement:
■
Position 2: 34¹⁄₄" to 34⁷⁄₁₆" (87 to 87.5 cm)
Position 3: 34⁷⁄₁₆" to 34⁵⁄₈" (87.5 to 88 cm)
NOTE: To level the unit in position 3, you may need to
add shims under the leveling legs.
Tighten screw.
■
Repeat for other rear wheel.
A. Countertop
B. Retaining bracket
7. Slowly lift the front slightly and roll compactor into the cabinet
opening.
Using the two #8-18 x ¹₂" screws, fasten the retaining
brackets to the countertop with the mounting screws.
If brackets cannot be attached to the underside of
countertop, attach mounting clips to brackets. Fasten
compactor to cabinet front with mounting screws through
mounting clips.
Countertop Mounting
B
A
C
1
2
3
A
C
D
A. Wheel bracket assembly
B. Cabinet
B
A. Countertop
B. Retaining bracket
C. Mounting screw
C. Locating stud
D. Self-tapping screw (pivot)
5
Installation
Cabinet-face Mounting
C
A
B
D
1. Remove the 2 rubber bumpers from the lower corners of the
inside drawer front. Set aside the bumpers and discard the
screws.
2. Align the bottom of the custom panel with the bottom of the
exterior drawer front and rest the panel on the rest tab.
NOTE: The bottom of the custom panel should not extend
below the bottom rest tab at the lower center of the exterior
drawer front.
3. Secure the custom panel to the exterior drawer front by using
four #8 x 1" wood screws from the inside drawer front.
■ Install the top 2 wood screws as shown.
A. Mounting clip
B. Cabinet
C. Retaining bracket
D. Mounting screw
8. Grasp sides of the compactor drawer and place the bottom
of the drawer into the tracks.
9. Lift at the handle so the drawer will go over the drawer stops.
10. Close the drawer.
11. Check that the drawer opens freely. If the toe plate rubs
against the floor, see “Adjusting the Toe Plate” for further
instructions.
Adjusting the Toe Plate
If the toe plate rubs the floor covering, the toe plate clearance
may be changed as follows:
1. Mark on each side of the toe plate the amount of toe plate
that rubs the floor covering.
2. Remove the drawer from the unit. See Step 3 in the
“Unpacking” section.
3. Use a ruler and a pencil or chalk to draw a line between the
marks on each side of toe plate.
4. Use scissors or utility knife to cut toe plate along line.
5. Replace the drawer. If the toe plate still rubs the floor
covering, repeat steps 1 to 4.
■
Use the bottom 2 wood screws to also re-install the
2 rubber bumpers on each side of the lower inside drawer
while attaching to the custom panel.
4. Attach a 15" x ¹⁄₂" (38.1 cm x 13 mm) quarter-round filler
along the top inside edge of the drawer front using glue or
screws.
A
B
C
D
D
E
Installing a Custom Panel
Dimensions
Use these dimension drawings to create a custom panel for use
without a trim kit. The panel should be a minimum of ¹⁄₂" (13 mm)
thick.
29 ³⁄₈"
(74.6 cm)
15"
(38.1 cm)
6
A. Custom panel
B. 15" x ¹⁄₂" (38.1 cm x 13 mm)
quarter-round filler
C. Drawer front
D. #8 x 1" wood screws
placement
E. Rubber bumper (one on
each side)
COMPACTOR USE
How Your Compactor Works
2. Place trash in compactor.
■ Wrap or cover wet or messy trash.
The compacting ram is the part of the compactor which
compresses the trash. The compacting ram does not go to the
bottom of the drawer. You will not see compacting of trash the
first few times you load the compactor.
NOTE: The compactor drawer should be more than ¹⁄₂ full before
the compactor can begin to compress the load.
You may hear a noise when glass breaks. Strong glass bottles
may not break at all. The trash in a full compactor bag will be
about ¹⁄₄ the size of its original bulk.
■
Do not compact items that may develop offensive odors
such as raw meat, fish, grapefruit rinds, disposable
diapers, or personal hygiene items.
■
Load bottles or cans on their sides in the center of the
drawer. Do not load bottles in an upright position.
3. Close the drawer.
WHISPER QUIET® Plus System
Load bulky trash, bottles, and cans in the center of the drawer.
Bottles or cans not placed in the center may become caught
between the ram and the drawer. The Drawer Monitor Switch
then senses a “misload” and causes the ram to return to the “up”
position without compacting.
The WHISPER QUIET® Plus system helps to maintain a quiet
home environment during compactor operation.
NOTE: The contents of the trash may affect the noise level of
your compactor. See “Compactor Use.”
Starting the Compactor
1.
2.
3.
4.
5.
Open the container. Load trash.
Leave the Key-Knob in the ON position.
Set the Solid Cycle switch to OFF.
Close the container.
Press the foot-actuated START pedal to begin cycle.
Using Solid (Locked) Cycle
Loading
IMPORTANT: Do not push items down into compactor with
hands or feet.
NOTE: You will not see compacting of trash the first few times
you load the compactor. The compactor drawer should be about
¹⁄₂ full before the compactor can begin to compress the load.
1. Open the drawer. Lift and pull the handle or press the toe bar
to open the drawer.
NOTE: Pressing the toe bar opens the container only 3" to 6"
(7.6 cm to 15.2 cm), depending on the load.
The Solid (Locked) Cycle extends the use of the bag by putting
constant pressure on the trash to keep it from springing back.
Regular use of solid cycle can increase bag capacity up to
25 percent.
During Solid Cycle, the ram will stay in the down position for
extra compacting. The drawer is locked and cannot be opened
when the ram is down.
For best results, use the Solid Cycle for at least 30 minutes at a
time.
1. Open the container. Load trash.
2. Set the Solid Cycle switch to ON.
3. Close the container.
4. Press the foot-actuated START pedal to begin cycle.
5. The container remains LOCKED untill you RESET by pressing
the foot-actuated START pedal.
7
Using the Air Filter or Freshener
Installing a New Bag
1. Set the Air Filter switch to ON. The fan creates air movement
in the compactor for odor removal.
NOTE: The charcoal Air Flter works only when the Key-Knob
is in the ON position.
Do not use any kind of bag other than those designed especially
for use in your compactor. Order replacement compactor bags
through your local dealer or by calling the toll-free number on the
cover or in the “Assistance or Service” section.
IMPORTANT:
Before installing a new bag, be sure:
■ The drawer side is securely locked.
IMPORTANT: The air freshener will work with or without the
fan.
2. Set the Air Filter switch to OFF to turn off the fan.
■
The container is clean and free of debris.
1. Place folded bag into the drawer. Open bag and pull top
edges over the drawer top.
Removing a Filled Bag
When the trash is compacted to the top of the drawer, remove
the bag. If the bag is too heavy, compact less trash before
emptying it in the future.
IMPORTANT: Do not push items down into compactor with
hands or feet.
1. Pull the drawer completely open.
2. Remove top of bag from bag retainer buttons. Pull up all
4 bag cuffs. Close bag with twist tie provided.
3. Push Side-Lock Latch down and tilt drawer side open.
4. Lift out bag.
8
2. Lock bag in place by pulling the 4 prepunched holes over the
bag retainer buttons. Holes will expand over the buttons
without damaging the bag.
3. Press inside of bag against the drawer bottom, sides and
corners for a smooth fit.
COMPACTOR CARE
Your new compactor is designed to give you many years of
dependable service. However, there are a few things you are
expected to do in order to properly maintain your compactor.
This section will tell you how to clean and care for your
compactor.
Changing the Air Filter or Freshener
It is recommended that you use either the charcoal air filter or the
air freshener in the filter compartment. The solid air freshener
system is an alternative to the air filter and is designed to control
odors that might develop in the trash.
To order the correct replacement charcoal filters or air fresheners,
call the toll-free number listed on the cover or in the “Assistance
or Service” section.
1. Insert fingertips in the air filter cover and pull until the side
tabs release. Then, lift the cover to release the bottom tabs.
Cleaning Inside the Drawer
NOTE: You may want to wear gloves since there may be bits of
glass in the drawer.
1. Remove the bag. See “Removing a Filled Bag.”
2. Press down on the lever-action lock (or Side-Lock latch).
3. Hold the lever-action lock down and tilt the side of the drawer
out until the lock clears the drawer front.
NOTE: If desired, the drawer side can be removed by tilting it
up, then lifting it out.
2. Remove the air filter by pulling the top edge of the filter. The
filter should pull out easily. Throw away used filter.
OR
Remove the air freshener by simply lifting out of the filter
compartment. Throw away used freshener.
3. To replace air filter, push the replacement filter into place.
OR
To replace the air freshener, place the replacement in the filter
compartment.
4. Insert the bottom tabs of the air filter cover and push in until
the side tabs snap into place.
Cleaning
4. Wash the interior of the drawer with a clean sponge or soft
cloth and a mild detergent in warm water. Rinse and dry
thoroughly with a soft cloth.
5. If the drawer side was removed, slide it back into the tilted
position.
6. Press the lever-action lock (or Side-Lock Latch) down while
pushing the drawer side to the upright position.
7. Latch the drawer side by pushing up the lever-action lock (or
Side-Lock Latch).
Cleaning Inside the Cabinet
NOTE: You may want to wear gloves since there may be bits of
glass in the cabinet.
1. Pull the drawer out until it stops.
NOTE: Look to see how the drawer rollers move in the tracks.
It will be easier to replace the drawer after you have finished
cleaning.
Before cleaning the compactor, turn the Key-Knob (or KeySwitch) to the OFF & LOCK position and remove it.
NOTE: Any services other than those outlined in this section
should be performed by a designated service representative.
Cleaning Exterior Surfaces
1. Wash exterior surfaces (including stainless steel) with a clean
sponge or soft cloth and a mild detergent in warm water. Do
not use abrasive or harsh cleaners. Rinse and dry thoroughly
with a soft cloth.
2. Wipe up spills right away. Some foods can damage the finish
if left on the compactor surface.
2. Lift the front of the drawer to clear the stops.
9
3. Grasp the drawer on the sides and pull it out the rest of the
way. Set the drawer down gently.
Cleaning the Ram
NOTE: You may want to wear gloves since there may be bits of
glass on the ram cover.
1. Wipe glass particles off of the ram cover with a cloth or paper
towels.
2. Remove foods with a clean sponge or soft cloth and a mild
detergent in warm water. Rinse and dry thoroughly with a soft
cloth.
4. Vacuum the inside of the cabinet. Liquid spills or wet trash
should be cleaned up by hand, or by using a vacuum cleaner
designed to pick up liquids.
Cleaning Before a Vacation
5. Wash the inside of the cabinet with a clean sponge or soft
cloth and a mild detergent in warm water. Rinse and dry
thoroughly with a soft cloth.
6. To replace the drawer, grasp it by the sides and insert the
rollers onto the tracks.
7. Lift the front of the drawer and push it in fully past the stops.
If you will be away for more than a couple of days, remove the
compactor bag. Remove the Key-Knob (or Key-Switch) and store
it out of children’s reach.
TROUBLESHOOTING
Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.
Trash is not compacting
Is the drawer less than half-full? Drawer must be more than
half full before trash is compacted.
■
The drawer won’t open
■
To raise the ram on models with a Key-Knob (or KeySwitch): Turn the Key-Knob (Key-Switch) to START and
release. See “Starting the Compactor.”
Your compactor won’t operate
■
Is the power supply cord unplugged? Plug into a grounded
3 prong outlet.
■
Has a household fuse blown, or has a circuit breaker
tripped? Replace the fuse or reset the circuit breaker. If the
problem continues, call an electrician.
■
Is the drawer completely closed? Close the drawer firmly
and start the compactor again.
■
Is the Key-Knob turned all the way to START? Turn the
Key-Knob (Key-Switch) fully to START and release (on some
models). See “Starting the Compactor.”
■
Did you press ON before pressing START? Press ON
before pressing START (on some models). See “Starting the
Compactor.”
10
Is the ram all the way up? Drawer will open only when ram is
fully raised.
To raise the ram on models with push button controls:
Press OFF, and then press ON. See “Starting the Compactor.”
■
Is the Solid Cycle engaged? Drawer remains LOCKED until
you reset by lifting the foot pedal up.
There is not enough compaction or force
■
Do you use the compacting cycle frequently enough?
Compacting works best when only a few items are loaded.
Bottles don’t break
■
How often do you notice this? Bottles will not break every
time. The thickness of the bottle’s glass and the content of
the trash load below it may keep the bottle from breaking.
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check
“Troubleshooting.” It may save you the cost of a service call. If
you still need help, follow the instructions below.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
If you need replacement parts
If you need to order replacement parts, we recommend that you
use only factory specified parts. These factory specified parts will
fit right and work right because they are made with the same
®
precision used to build every new KITCHENAID appliance.
To locate factory specified parts in your area, call us or your
nearest KitchenAid designated service center.
In the U.S.A.
Call the KitchenAid Customer eXperience Center toll free:
1-800-422-1230 or visit our website at www.kitchenaid.com.
To locate the KitchenAid designated service company in your
area, you can also look in your telephone directory Yellow
Pages.
Our Consultants Provide Assistance With:
■
Features and specifications on our full line of appliances.
■
Installation information.
■
Use and maintenance procedures.
■
Accessory and repair parts sales.
■
Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.).
■
Referrals to local dealers, repair parts distributors and service
companies. KitchenAid designated service technicians are
trained to fulfill the product warranty and provide afterwarranty service, anywhere in the United States.
For Further Assistance
If you need further assistance, you can write to KitchenAid with
any questions or concerns at:
KitchenAid Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
In Canada
Call the KitchenAid Canada Customer eXperience Centre toll
free: 1-800-807-6777 or visit our website at www.kitchenaid.ca.
Our Consultants Provide Assistance With:
■
Features and specifications on our full line of appliances.
■
Use and maintenance procedures.
■
Accessory and repair parts sales.
■
Referrals to local dealers, repair parts distributors and service
companies. KitchenAid Canada designated service
technicians are trained to fulfill the product warranty and
provide after-warranty service, anywhere in Canada.
For Further Assistance
If you need further assistance, you can write to KitchenAid
Canada with any questions or concerns at:
Customer eXperience Centre
KitchenAid Canada
200 - 6750 Century Ave.
Mississauga, Ontario L5N 0B7
Please include a daytime phone number in your correspondence.
Accessories
To ensure the proper functioning of your compactor, use
KITCHENAID® replacement parts only. To order replacement
parts or accessories, call 1-800-462-3819 and ask for the
appropriate part number listed below or contact your authorized
KitchenAid dealer. In Canada, call 1-800-807-6777.
Color Panel Kits and Handles
See section “Installing a Custom Panel” for custom panel
dimensions.
■ Color Panel with Handles:
Replacement Parts
Cobalt Blue—Part Number 4396299
■
Replacement Bags: Call for Part Number.
Empire Red—Part Number 4396300
■
Charcoal Air Filters: Part Number 4151750
Majestic Yellow—Part Number 4396301
■
Air Fresheners (scent):
Black—Part Number 4396296
Fresh Green Apple—Part Number 9872166GA
White—Part Number 4396297
Lavender—Part Number 9872166L
Lemon Grove—Part Number 9872166LG
Biscuit—Part Number 4396298
■
Handles:
Brushed Stainless Steel—Part Number 9871564
White—Part Number 9871564W
Black—Part Number 9871564B
Biscuit—Part Number 9871564T
11
KITCHENAID® COMPACTOR WARRANTY
ONE YEAR LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or
furnished with the product, KitchenAid or KitchenAid Canada (hereafter “KitchenAid”) will pay for factory specified parts and repair
labor to correct defects in materials or workmanship. Service must be provided by a KitchenAid designated service company.
30 DAY LIMITED WARRANTY ON THE CHARCOAL FILTER AND AIR FRESHENER
For thirty days from the date of purchase, when the compactor is installed, operated and maintained according to instructions attached
to or furnished with the product, KitchenAid will provide a replacement filter or air freshener if the original filter or air freshener fails due
to defects in materials or workmanship.
1.
2.
3.
4.
5.
6.
7.
8.
9.
ITEMS KITCHENAID WILL NOT PAY FOR
Service calls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair
house fuses or to correct house wiring or plumbing.
Service calls to repair or replace appliance light bulbs or water filters. Those consumable parts are excluded from warranty
coverage.
Repairs when your major appliance is used for other than normal, single-family household use.
Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in
accordance with electrical or plumbing codes, or use of products not approved by KitchenAid.
Replacement parts or repair labor costs for units operated outside the United States or Canada.
Pickup and delivery. This major appliance is designed to be repaired in the home.
Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
Expenses for travel and transportation for product service in remote locations.
The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with
published installation instructions.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED
HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. KITCHENAID SHALL NOT BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE
TO PROVINCE.
Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized KitchenAid dealer to determine if
another warranty applies.
If you need service, first see the “Troubleshooting” section of the Use & Care Guide. After checking “Troubleshooting,” additional help
can be found by checking the “Assistance or Service” section or by calling KitchenAid. In the U.S.A., call 1-800-422-1230. In Canada,
9/05
call 1-800-807-6777.
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your major appliance
to better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial
number. You can find this information on the model and serial
number label located on the product.
Dealer name____________________________________________________
Address ________________________________________________________
Phone number __________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________
W10242569B
®
/™ ©2013 KitchenAid. Used under license in Canada. All rights reserved.
11/13
Printed in U.S.A.
Download PDF

advertising