AII 24193 CD Changer Attachment.pmd

AII 24193 CD Changer Attachment.pmd
INSTALLATION
INSTRUCTIONS
Accessory
Application
CD CHANGER ATTACHMENT
2003 CIVIC
4-DOOR
Publications No.
AII 24193
Issue Date
AUG 2002
PARTS LIST
CD Changer Attachment (Sold separately)
P/N 08B26-S5D-100
BUS cable
CD Changer bracket
4 Washer screws
CD Changer (Sold separately)
P/N 08A26-1B1-100
Right side bracket
CD Changer
Left side bracket
3 Clip nuts
Owner’s Manual
CD magazine
3 Washer-bolts
4 Washer-screws, 4 x 6 mm
(Not used)
20 Wire ties
Adhesive seal sheet
4 Cap nuts
Locking covers
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
AII 24193 (0208)
08B26-S5D-1002-91
1 of 12
TOOLS REQUIRED
3.
Phillips screwdriver
Open the trunk lid, and remove the two clips
fastening the trunk floor mat. Remove the trunk
floor mat and the trunk floor.
Flat-tip screwdriver
CLIP
TRUNK FLOOR MAT
Stubby Phillips screwdriver
10 mm Combination wrench
Clip remover
8 mm and 10 mm Sockets
Ratchet
TRUNK FLOOR
Small flat-tip screwdriver
Illustration of the CD Changer Installed on the Vehicle
AUDIO UNIT
BUS CABLE
4.
Remove the trunk weatherstrip from the edge of
the trunk opening in the area shown.
5.
Remove the rear trim panel by removing the four
clips and releasing the three hooks.
CD CHANGER
HOOKS (3)
INSTALLATION
REAR TRIM
PANEL
CLIPS (4)
Customer information: The information in this
installation instruction is intended for use only by
skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
equipment to your car. These procedures should not
be attempted by “do-it-yourselfers.”
1.
Make sure you have the anti-theft code for the
radio, then write down the frequencies for the
preset buttons.
2.
Disconnect the negative cable from the battery.
TRUNK
WEATHERSTRIP
2 of 12
AII 24193 (0208)
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
6.
Continue removing the trunk weatherstrip in the
area shown, and remove the three clips, then pull
out on the right trunk side trim panel in the
direction shown.
8.
CLIP
Turn the center pin in
a counterclockwise
direction to remove.
Remove the bolt, pull the hook toward the rear of
the car, then pull the bolster out toward you in the
direction shown, remove the right seat side bolster.
3
HOOK
1
RIGHT SEAT SIDE
BOLSTER
2
BOLT
CLIP
RIGHT TRUNK SIDE
TRIM PANEL
9.
Pry up on the six retaining tabs, and remove the
B-pillar lower trim panel.
TRUNK
WEATHERSTRIP
7.
Inside the passenger’s compartment area, remove
the rear seat cushion by removing the bolt and
releasing the two hooks.
FRONT
BOLT
B-PILLAR
LOWER
TRIM PANEL
RETAINING
TABS (6)
HOOK
REAR SEAT CUSHION
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
AII 24193 (0208)
3 of 12
10. Remove the four clips, release the two retaining
tabs fastening the right seat side trim, and remove
the trim. Take care not to damage the clips.
RIGHT SEAT
SIDE TRIM
•
Remove the two self-tapping screws, two
screws and two clips fastening the center
console and remove the console.
•
Place the shift lever in the Neutral position.
•
On the M/T model, remove the shift knob from
the lever by holding the plastic section above
the boot down firmly with one hand and turning
the knob in a counterclockwise direction.
•
If equipped with an optional armrest, remove
the console after reclining the seat-back.
RETAINING TABS (2)
SELF-TAPPING
SCREW
CLIP
CENTER
CONSOLE
CLIP
FRONT
SHIFT
KNOB
CLIPS (3)
11. Remove the dashboard center lower cover and the
center console.
SCREW
Normal Center Console
•
Pull up on the parking brake lever, then remove
the console box (nine clips).
BOOT
(M/T Model)
SHIFT LEVER
Place in the
Neutral position.
PLASTIC SECTION
CLIPS (9)
CONSOLE BOX
PARKING BRAKE LEVER
Pull up completely.
4 of 12
AII 24193 (0208)
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
With Armrest
Without a Cigarette Lighter and Ashtray:
•
With the parking brake applied, place the gear
shift lever in the Neutral position.
•
Pry up on the four retaining tabs and remove
the escutcheon.
•
Gently pry out on the lower cover to release the
six retaining clips.
•
Pry up on the the three clips and six retaining
tabs and remove the center console trim.
•
Unplug the accessory power socket connector
(if equipped, unplug the fog light harness), and
remove the lower cover.
CENTER CONSOLE
TRIM
ESCUTCHEON
RETAINING
TABS (6)
ACCESSORY
POWER SOCKET
CONNECTOR
CLIP (3)
RETAINING
TABS (4)
FOG LIGHT SWITCH
CONNECTOR
(If equipped)
CLIPS (6)
DASHBOARD
CENTER LOWER
COVER
FOG LIGHT
SWITCH
(If equipped)
With a Cigarette Lighter and Ashtray:
•
With the parking brake applied, place the gear
shift lever in the Neutral position.
•
Remove the ashtray.
•
Inside the ashtray opening, remove the one
self-tapping screw securing the dashboard
center lower cover.
•
Gently pry out on the lower cover to release
the six retaining clips.
•
Unplug the cigarette lighter harness, and
illumination bulb (if equipped, unplug the fog
light harness), then remove the lower cover.
Without a Cigarette Lighter and Ashtray:
•
With the parking brake applied, place the gear
shift lever in the Neutral position.
•
Remove the two self-tapping screws fastening
the dashboard center lower cover.
•
Gently pry out on the dashboard center lower
cover to release the nine clips and one
retaining tab.
•
Unplug the accessory power socket connector
(if equipped, unplug the fog light harness), and
remove the dashboard center lower cover.
CLIPS (9)
FOG LIGHT
SWITCH
(If equipped)
ILLUMINATION BULB
CIGARETTE
LIGHTER
CONNECTORS
FOG LIGHT
SWITCH
CONNECTOR
(If equipped)
ACCESSORY
SOCKET
CONNECTOR
RETAINING
TAB
SELFTAPPING
SCREW
DASHBOARD
CENTER
LOWER
COVER
FOG LIGHT
SWITCH
(If equipped)
RETAINING
CLIPS (6)
SELF-TAPPING
SCREW
ASH TRAY
FOG LIGHT
SWITCH
CONNECTOR
(If equipped)
DASHBOARD CENTER
LOWER COVER
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
AII 24193 (0208)
5 of 12
With a Cigarette Lighter and Ashtray:
•
•
With the parking brake applied, place the gear
shift lever in the Neutral position.
•
Open the center console lid, and remove the
mat.
•
Remove the cap. Remove the two clips, five
self-tapping screws and two screws fastening
the center console, and remove the center
console.
•
Place the shift lever in the Neutral position.
•
On the M/T model, remove the shift knob from
the lever by holding the plastic section above
the boot down firmly with one hand and turning
the knob in a counterclockwise direction.
Remove the ashtray. Inside the ashtray
opening, remove the one self-tapping screw.
Remove the two self-tapping screws fastening
the dashboard center lower cover.
•
Gently pry out on the dashboard center lower
cover to release the nine clips and one
retaining tab.
•
Unplug the cigarette lighter harness, accessory
power socket connector, and illumination bulb,
then remove the lower cover.
SELFTAPPING
SCREW
CLIPS (2)
RETAINING TAB
DASHBOARD
CENTER
LOWER
COVER
CENTER
CONSOLE
LID
MAT
CENTER
CONSOLE
ASHTRAY
SELFTAPPING
SCREW
SHIFT
KNOB
SCREW
PLASTIC
SECTION
(M/T Model)
ILLUMINATION
BULB
6 of 12
SHIFT LEVER
Place in the
Neutral
position.
BOOT
CLIPS (9)
CIGARETTE
LIGHTER
CONNECTOR
AII 24193 (0208)
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
12. Remove the center panel:
•
Remove the two bolts from the bottom of the
center panel.
•
Reach through the bottom opening, and push
out on center panel bracket to release the nine
retaining clips.
•
15. Visually check the position of the spring adjusting
pins on both sides of the CD changer. If both of
the spring adjusting pins are not in the horizontal
(H) position, move the pins to the horizontal
position with a small flat-tip screwdriver.
SPRING ADJUST PIN
COVER PLATE
(furnished with
CD Changer Kit)
Unplug the five vehicle connectors and the
antenna lead, then remove the center panel.
CENTER PANEL
VEHICLE
CONNECTORS (5)
COVER PLATE
(furnished with
CD Changer Kit)
SPRING ADJUST PIN
(H: HORIZONTAL)
COVER PLATE
ANTENNA
LEAD
(V: VERTICAL)
CLIPS (9)
16. Remove the adhesive backings from the “L” and
“R” locking covers, and attach them to the side of
the CD changer. Align the two diagonally opposite
holes with the H and V positions.
Push
BOLT
CENTER PANEL BRACKET
Installing the CD Changer
13. Carefully unpack the CD changer. Remove the
three shipping clips, and discard the shipping
cover. Save the shipping clips for your customer in
the event the unit needs to be serviced.
17. Slide a clip nut onto the rear parcel shelf through
the hole in the parcel shelf and align their holes as
shown. Install the washer-bolt and tighten it
securely.
CLIP NUT
14. Install an adhesive seal (included in the CD
Changer) over each of the three shipping clip
holes.
SHIPPING CLIPS (3)
HOLE in BODY
PANEL
SHIPPING COVER
(Discard.)
SHIPPING
SEALS (3)
REAR
PARCEL
SHELF
CD
CHANGER
BRACKET
WASHERBOLT
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
AII 24193 (0208)
7 of 12
18. Slide the two clip nuts onto the CD changer
brackets and parcel shelf through the holes in the
parcel shelf and align their holes as shown. Install
the two washer-bolts and tighten them securely.
20. Position the CD changer on the CD changer
bracket, and install a cap nut on the end of each
stud extending from the CD changer.
CD CHANGER
CLIP NUT
RIGHT SIDE
BRACKET
CD CHANGER
BRACKET
CD CHANGER
BRACKET
CLIP NUT
CLIP NUT
LEFT SIDE
BRACKET
WASHERBOLT
CD CHANGER
BRACKET
CLIP NUT
WASHER-BOLT
CAP NUT
Routing the BUS Cable
CD CHANGER
BRACKET
19. Position the side brackets on the CD changer, and
install the four washer-screws supplied with the
CD Changer Attachment. Note the direction of the
side brackets. The extra hole in each of the
brackets should face the front of the CD changer.
Tighten the washer-screws securely.
21. Connect the BUS cable connector to the
connector from the CD changer.
LEFT SIDE
BRACKET
RIGHT SIDE
BRACKET
CD CHANGER
BUS CABLE
WASHER-SCREWS (4)
(furnished with CD
Changer Attachment)
8 of 12
CD CHANGER
CD CHANGER CONNECTOR
AII 24193 (0208)
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
22. Secure the connector and BUS cable to the CD
changer bracket with three wire ties in the areas
shown.
24. Remove the clip, and turn over the carpet as
shown. Continue routing the BUS cable.
CARPET
CLIP
CD CHANGER
BRACKET
WIRE TIE
BUS CABLE
CONNECTOR
BUS CABLE
Route under the
carpet.
23. Inside the trunk, route the other end of the BUS
cable into the passenger’s compartment through
the hole in the panel.
BUS CABLE
VEHICLE
HARNESS
VEHICLE HARNESS
25. Route the BUS cable forward under the parking
brake lever base and to the right front console
frame along the vehicle harness.
26. Route the BUS cable connector through the
clearance between the right front console frame
and the dashboard and out through the dash
opening.
DASH OPENING
BUS CABLE
RIGHT FRONT
CONSOLE FRAME
Route under the
parking brake
lever base.
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
AII 24193 (0208)
Route between the
front console frame
and instrument panel.
9 of 12
27. Pull the vehicle 20-pin connector (blue) and BUS
cable connector out through the dash opening;
then secure them to the vehicle harness with the
wire tie in the area shown.
29. Secure the BUS cable to the vehicle harness with
eight wire ties in the areas shown.
VEHICLE 20-PIN CONNECTOR
(BLUE)
WIRE TIE
VEHICLE
HARNESS
WIRE TIE
BUS CABLE
Pull the BUS cable out
as far as the vehicle
20-pin connector
harness (blue).
WIRE TIE
BUS CABLE
WIRE
TIE
VEHICLE
HARNESS
30. Bundle up the excess cable, and secure it to the
vehicle harness with two wire ties.
28. Secure the BUS cable to the vehicle harness with
six wire ties in the areas shown.
WIRE TIE
Bundle up the
excess cable.
DASH
OPENING
VEHICLE
HARNESS
BUS CABLE
BUS CABLE
WIRE
TIE
BUS
CABLE
WIRE TIE
VEHICLE
HARNESS
VEHICLE
HARNESS
10 of 12
AII 24193 (0208)
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
31. Plug the BUS cable connector, vehicle 20-pin
connector (blue), and antenna lead into the rear of
the audio unit.
32. Connect the four vehicle connectors to the center
panel, and reinstall the center panel.
When Radio and Pocket Are Installed
VEHICLE CONNECTORS (4)
CENTER PANEL
RADIO
BUS CABLE
CONNECTOR
ANTENNA
LEAD
ANTENNA
LEAD
VEHICLE 20-PIN
CONNECTOR
(BLUE)
BUS CABLE
VEHICLE 20-PIN
CONNECTOR (BLUE)
POCKET
BOLT (reused)
When Radio and Cassette Player Are Installed
RADIO
33. Check that all wire harnesses are routed properly
and all connectors are plugged in.
34. Reconnect the negative cable to the battery.
35. Reset the clock and the radio station presets.
ANTENNA
LEAD
36. Check the operation of the CD changer as
described in the Owner’s Manual supplied.
37. Reinstall all removed parts. Be sure that all
retaining clips and tabs are securely fastened.
38. Put the CD changer Owner’s Manual and the
shipping clips (removed in step 13) in the glove
box for your customer.
VEHICLE 20-PIN
CONNECTOR
(BLUE)
BUS CABLE
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
CASSETTE
PLAYER
AII 24193 (0208)
11 of 12
39. Do the ECM/PCM idle learn procedure.
– Make sure all electrical items are turned off.
– Start the engine. Hold the engine speed at
3,000 rpm with no load (in Park or Neutral) until
the radiator fan comes on.
– Let the engine idle for about 5 minutes with the
throttle fully closed and with all electrical items
off.
NOTE: If the radiator fan comes on during this
step, the time when it is operating must not be
included in the 5 minutes.
NOTE: Whenever the battery is disconnected, the
driver’s window AUTO function is disabled.
40. Start the engine. Push down on the driver’s
window switch until the window is fully open.
41. Pull up on the driver’s window switch to close the
window completely, then hold the switch for
2 seconds.
42. Lower and raise the driver’s window to check
operation of the driver’s window AUTO function.
12 of 12
AII 24193 (0208)
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement