Isolation Signal Splitter D6N 21000 Conversion, Isolation and Distribution of Standard Signals With the Isolation Signal Splitter D6N 21000 DRAGO is extending its offer on high-functional and high-reliable components of the interface technique. • Calibrated signal setting Input and output range can be set by using DIP switch without any further adjustment The Isolation Signal Splitter D6N 21000 is used for isolation, conversion and distribution of 0/4 ... 20 mA, 0/1 ... 5 V and 0/2 … 10 V standard signals. The input and two outputs each can be separately configured. The signal combination is selectable by DIP switch. Its high level of reliability and extremely slim form make the D6N 21000 the first choice in its class! • 4-Port isolation Protection against erroneous measurements due to parasitic voltages or ground loops The Protective Separation with high isolation level provides protection for personnel and downstream devices against impermissibly high voltage and make the D6N 21000 universally applicable for all measurement and industrial applications. • Protective Separation acc. to EN 61140 Protects service personnel and downstream devices against impermissibly high voltage Pluggable cross-connectors for the auxiliary power supply ensures fast and economical installation. The slim housing with 6.0 mm wide saves significant space on DIN-rail in the switch cabinet. The optimized efficiency of the D6N 21000 power pack contributes significantly to reducing the units own heat generation. This is reflected in extremely high MTBF, it means highest reliability and long-term stability. A green LED on the front of the unit has been provided to monitor the power supply. Block diagram • Extremely slim design 6.0 mm small housing with practical pull-spring clamps • Maximum reliability No maintenance costs • 5 Years Warranty Isolation Signal Splitter D6N 21000 Technical Data Input Input signal Input resistance Overload Output I Output II Output signal Load Offset Ripple General Data Transmission error Temperature coefficient 1) Cut-off frequency Response time (T10-90) Prüfspannung Working voltage2) (Basic Insulation) 0 ... 20 mA 0 ... 5 V Current input Voltage input Current input Voltage input 4 ... 20 mA 0 ... 10 V 0 ... 20 mA ≤ 10 V < 20 µA < 10 mVrms 4 ... 20 mA see order information 1…5V ≤ 50 Ω ≥ 100 kΩ ≤ 50 mA ≤ 30 V 2 … 10 V see order information (2 x 300 Ω at 20 mA) < 0.1 % of final value < 100 ppm/K 1 kHz switchable to 100 Hz < 300 µs switchable to < 3.5 ms 2.5 kV, 50 Hz Input against Output I against Output II against power supply Up to 600 V AC/DC for overvoltage category II and pollution degree 2 acc. to EN 61010-1 between all circuits. Protective separation according to EN 61140 by reinforced insulation in accordance with EN 61010-1 up to 300 V AC/DC for overvoltage category II and pollution degree 2 between all circuits. (–13 to +158 °F) Operation –25 °C to + 70 °C (–40 to +185 °F) Transport and storage –40 °C to + 85 °C 24 V DC 16.8 … 31.2 V DC, approx. 1.0 W EN 61326–1 6.0 mm housing, protection class: IP 20 Approx. 50 g Protection against electrical shock Ambient temperature Power supply EMC3) Construction Weight 1) 2) Average TC based on the final value in specified operating temperature range As far as relevant the standards and rules mentioned above are considered by development and production of our devices. In addition relevant assembly rules are to be considered by installation of our devices in other equipments. For applications with high working voltages, take measures to prevent accidental contact and make sure that there is sufficient distance or insulation between adjacent situated devices. 3) Minor deviations possible during interference Bold: Factory settings for D6N 21000 Dimensions Product line Device Order No. Isolation Signal Splitter, calibrated range selection D6N 21000 Isolation Signal Splitter, customer specific preselection D6N 21005 – Input Output I Output II Example: X 0 ... 20 mA 0 4 ... 20 mA 1 0…5V 0 … 10 V 2 3 1…5V 4 2 … 10 V 5 0 ... 20 mA 4 ... 20 mA X X 0 1 Terminal assignments 0 ... 20 mA 0 4 ... 20 mA 1 Input: 0 … 10 V, Output I and II: 4 … 20 mA Order No.: D6N 21005 – 311 Pull-spring clamps Wire cross-section max. 2,5 mm2 Stripped length 9 … 10 mm 1 2 3 4 Input + Input – Output II+ Output II – 5 6 7 8 Output I+ Output I – Power supply + Power supply – Subject to change ! DRAGO Automation GmbH - Waldstraße 86-90 - 13403 Berlin - Germany - www.drago-automation.de
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021