220V Access Electric Projection Screen by Draper

220V Access Electric Projection Screen by Draper
US Patent Nos.
6,137,629; 6,421,175;
6,532,109; 6,816,308;
7,559,707
⑤ Front, back and top of case must be straight—not forced to warp or bow.
⑥ If case is painted on location, removal of roller/fabric assembly is
recommended prior to painting. If not removed, slot on bottom of case
should be shielded to protect viewing surface from paint splatters or
overspray.
⑦ Do not seal unit in ceiling until electrical connections have been made and
screen has been operated successfully.
Installation/Operating Instructions
220V Access Electric Projection Screen by Draper
These Installation/Operating Instructions are available in the official language
of the country where you purchase the product. Please contact your distributor
to request a copy.
Vous pourriez demander les instructions d’installation et d’opération traduises
dans la langue officielle du pays ou vous achetez le produit. Veuillez
demander à votre distributeur.
Die Gebrauchsanweisung für Installation und Konstruktion sind in der
offiziellen Sprache des Landes, indem Sie das Produkt gekauft haben,
vorhanden. Fragen Sie die jeweilige Verkaufs-Abteilung.
Caution
① Read instructions through completely before proceeding; keep them
for future reference. Follow instructions carefully. Installation contrary to
instructions invalidates warranty. Care in mounting and correct operation
will mean long and satisfactory service from your Draper screen.
② Allow enough access to remove front cover should fabric become
damaged or should other service be required.
③ Screen should be installed level (using a carpenter’s level).
④ Nothing should be fastened to screen dowel or viewing surface
⑤ Operating switch (es) is packed separately in screen carton. Do not
discard with packing material.
⑥ Screen operates on 220V AC, 50 Hz., 1ph. current.
NOTE: Screen has been thoroughly inspected and tested at factory and
found to be operating properly prior to shipment.
Hanging Screen
When locating viewing surface and checking clearance for screen operation,
remember surface is centered in the length of the case. Regardless of
mounting method used, the following points apply:
① Mounting brackets are shipped attached to the case. Engage each bracket
with top of housing as shown below and tighten set screws. A bracket
should be within 46 cm of each end of screen case. Brackets can be
removed and case mounted with lag screws through top of case (holes
drilled on site).
② Screen should be positively and securely supported so that vibration or
even abusive pulling on viewing surface will not weaken installation.
③ Installer must insure that fasteners used are of adequate strength and
suitable for the mounting surface chosen. Supporting hardware (chains,
cables, rods, etc.) must be essentially vertical.
④ Entire bottom of case must be readily accessible after installation is
complete.
Remove
shipping
brackets
before
operating
screen.
Typical
Installation
Electrical Connections
Screen operates on 220V AC, 50 Hz., 1 ph current.
Junction box is located just above the bottom access panel at left end of
screen (standard, right end may be specified).
Remove the bottom access panel for access to the junction box cover. (See
Bottom Access Panel Removal instructions below). Remove four (4) hex head
screws that secure the cover to the junction box to expose the blue, brown
and black pigtail leads and the green ground wire (if they aren't already exiting
the case via the cable knockout) per wiring diagram on page 3.
If optional low voltage control or video interface control is specified and factory
installed, please refer to wiring diagrams on page 4.
Screen is shipped with internal wiring complete and control switch(es) fully
boxed. Wire to connect screen to switch(es) and switch(es) to power supply
should be furnished by installer. Connections should be made in accordance
with attached wiring diagram, and wiring should comply with national and
local electrical codes.
All operating switches should be “off” before power is connected.
Bottom Access Panel Installation/Removal
Bottom access panel hooks over the lower inside edge of the screen housing
and then is pivoted downward until the engagement brackets on each end of
the bottom panel click into place with the ball detents on each endcap. Make
sure bottom access panel clicks in place at each end of its length.
Remove bottom access panel by pushing up at each corner of panel adjacent
to slot in bottom of the housing.
With bottom access panel angled up approximately at 20° it can be lifted off of
the lip of the housing and then lowered out of the housing completely.
Dowel
With bottom access panel
angled up approx. 20 degrees,
engage hook on the panel
with lip of the housing
Shipping
Bracket
Slots along top of case permit
brackets to be set at an angle
Alternate
Installation
(additional
set of
brackets
required but
Case dimensions
not included)
Using the hook and lip as a pivot,
pull the panel downward until the
engagement brackets click into
place with the ball detent
on each endcap
Engagement bracket
(one on each end of the
bottom access panel)
Bottom flange of Access housing
Bottom access panel pushup
points for panel removal
on page 3.
®
Caution: Beware of pinch
points at ends of closure
Access case as seen from below
Copyright © 2010 Draper Inc.
Form Access220V_Inst10-R2 Printed in U.S.A
If you encounter any difficulties installing or servicing your Access screen, call your
dealer or Draper, Inc., in Spiceland, Indiana, 765/987-7999 or fax 765/987-1689.
220V Access by Draper
page 2 of 4
Motorized Roller/Fabric Installation
Please note: When ordering a motor with built-in Low
Voltage Controller, if the case ships separate from the
"guts," the case includes the 25' cable and special low
voltage switch.
The bottom access panel must be removed first.
The motor end mounting bracket has a metal bracket
with snap ring for accepting motor head. Back out the
four set screws in bracket until they are flush with top
side of bracket.
Retaining
clip
To engage the motor end bracket flange above the two
channels in the top of the screen housing, rotate the
Motor roller
Washer
assembly
bracket approximately 45° counterclockwise to allow
Idler end roller
the top surface of the motor bracket to rest flat against
mounting bracket
the top inside of the housing. Rotating the bracket
clockwise until it is engaged with the channels, slide it
along the length of the housing against the electrical
junction box.
Engage the idler end bracket (rectangular mounting
pad) in the same manner as the motor end bracket and
slide it toward the opposite end of the screen housing.
Do not tighten the set screws on this bracket until the
roller/fabric assembly is installed, and centered in case.
Locate the black washer and retaining clip attached to
the instruction sheet.
Note: This step requires two people to perform
safely. Raise the roller/fabric assembly up into the
screen housing and engage the head of the motor
completely into the motor mounting bracket, making
sure the snap ring engages with the motor and that the
limit switch adjusting knobs are visible from the bottom
of the screen housing.
While supporting the idler end of the roller, slide the idler end mounting bracket
toward the roller. Insert the roller pin into the nylon bushing on the idler end
mounting bracket.
The roller idler pin needs to go through the idler bracket far enough to allow the
washer and retaining clip to be reinstalled on the pin.
Failure to replace the washer and retaining clip could result in the separation of the
roller from the brackets.
The roller/fabric assembly and roller brackets may need to be slid left or right in the
mounting channel of case to center fabric within screen case.
Securely tighten the set screws on roller mounting brackets.
Connect the electrical plug from the motor to the mating socket on the junction
box.
Reinstall the bottom access panel as previously described.
Motorized Roller/Fabric Removal
Reverse the instructions above “Motorized Roller/Fabric Installation” for removal of
the unit.
Operation
When screen is first operated, be cautious! Cycle unit down and up several times
to confirm satisfactory operation.
220V SINGLE STATION CONTROL—3-position UP-OFF-DOWN switch permits
operation to be stopped at any point. Factory adjusted limit switches automatically
stop screen when fully down or fully up.
220V MULTIPLE STATION CONTROL—(Not CE Approved) Switches are similar
in appearance to 220V Single Station Control. Screen stops when switch is
released and may be restarted in either direction. Factory adjusted limit switches
stop screen automatically when fully up or fully down.
24V CONTROL—Three-button UP-STOP-DOWN switches stop at any point
desired, operate in any sequence. Factory adjusted limit switches automatically
stop screen when fully up or fully down. Installer should incorporate an all-pole
disconnect in the fixed wiring.
220V & 12V VIDEO INTERFACE CONTROL—(Not CE Approved) Allows screen
to be controlled by a trigger signal—when the signal comes on, the screen
descends automatically. Two versions: Model VIC220 integrates screen operation
with a Draper video projector lift or a video projector or tuner with a 220V switched
outlet. Model VIC12 interfaces with a 12V switched outlet. Both available with an
override switch (VIC–OS), permitting independent operation. VIC–OS not available
with factory installed VIC220 & VIC12.
KEY OPERATED SWITCHING—(Not CE Approved) Two kinds of key-operated
switches are optionally available with this unit.
① The key-operated power supply switch controls power to the screen and
switches. When it is “off”, the switches will not operate screen. Key may be
removed from the switch in either “on” or “off” position.
② A three-position key switch permits the screen to be operated directly by
key. In this case, the screen’s operator must always have a key.
RS232/ETHERNET—Serial communication and network communication optionally
available with wall switches, RF or IR remote.
www.draperinc.com
Tab-Tension Adjustment Procedure for Access/Series V
Draper’s Tab-Tensioning System is factory-set; under normal circumstances field
adjustment is not required. If you notice wrinkles, waves or other indications that
tensioning cables need adjusting, follow these steps:
① Determine which side requires adjustment.
Tensioning
② Secure dowel with one hand.
Cable
Caution: Don't touch or bend viewing surface.
③ Use Phillips-head screwdriver to depress
spring-loaded adjustment screw. Slowly
Dowel
Adjustment
Screw
turn clockwise to tighten tension or
counterclockwise to loosen tension. The
screw adjusts in ¼ turn increments. Adjust
only one increment (¼ turn) at a time.
④ If problem is not corrected, leave screen in position for 24 hours to allow
surface material to stretch into position.
⑤ If problem still is not corrected, repeat steps 2 and 3.
Limit Adjustments (Standard and Quiet Motors)
Tools needed: Flashlight, small flathead screwdriver/Allen wrench (4mm or 5/32").
Screen settings have been factory set as ordered and should not normally
require further adjustment. However, if you find it necessary to adjust for more or
less viewing area, proceed as follows.
CAUTION: Always be prepared to shut screen off manually when new
adjustment is being tested. Screen may be severely damaged if viewing
surface is allowed to run too far up or too far down. When running up, the
dowel should never wrap over the roller. When run to the down limit, a
minimum of 1¼ wraps of fabric must remain on the roller.
The motor limit screws are normally located on the audience left of screen roller.
**Please Note: If the Access E/V is “Right Hand Motor” or “Waterfall”, the WHITE/
DOWN and YELLOW/UP limit screws are reversed. See graphic below.
"Down" Limit Adjustment
To Reduce Screen Drop
① Raise screen surface about 1' above desired setting and turn off.
② Turn the WHITE/DOWN limit screw clockwise (three screw turns = ½ roller
revolution).
③ Test by running screen down and repeat steps 1 and 2 until desired position is
reached.
To Increase Screen Drop
① Run screen to the down limit.
② With the down switch on, turn the WHITE/DOWN limit screw counterclockwise
(3 turns of screw equals ½ roller revolution) to increase drop.
③ Test by running screen up about 1' and back down to new down limit.
④ Repeat steps 2 and 3 until desired position is reached.
CAUTION: At least 1¼ wraps of fabric must remain on the roller when
screen is at the down limit!
"Up" Limit Adjustment
Screen is Running Too Far Up
① Lower screen surface about 1' below desired setting and turn off.
② Turn the YELLOW/UP limit screw clockwise (3 screw turns = ½ roller revolution).
③ Test by running screen up.
④ Repeat steps 1 through 3 until desired position is reached.
Screen Needs to Run Up More
① Run screen down about 1' and turn off.
② With the up switch on, turn the YELLOW/UP limit screw counterclockwise (3
turns of screw equals ½ roller revolution).
③ Repeat steps 1 and 2 until desired position is reached.
CAUTION: Do NOT allow the dowel to wrap up over the roller when the
screen is running up! This could damage the screen.
Audience
Side
Motor
End
Audience
Side
Standard Roll
Motor
End
Reverse Roll
Standard/Reverse Roll
Left hand motor
White Socket—Down
Yellow Socket—Up
Right hand motor
White Socket—Up
Yellow Socket—Down
(765) 987-7999
Audience
Side
Motor
End
Waterfall Roll
Waterfall Roll
Left hand motor
White Socket—Up
Yellow Socket—Down
Right hand motor
White Socket—Down
Yellow Socket—Up
220V Access by Draper
page 3 of 4
Case Dimensions
Mounting brackets slide
left and right as needed.
22.9
cm
17.8
cm
16.8
cm
5.4
slot
2.3
cm
2.3
cm
20.3 cm
Mounting
hardware
supplied by
others
2.6
cm
L
Access
L
Series E 17.8 cm
Series V Varies
Engagement bracket (one on each end
of the bottom access panel) clicks into
place with the ball detent on each endcap
Series E or M
Series V
Wiring Diagrams—220V Standard and Quiet Motor
Please Note: Do not wire motors in parallel.
Single Station Control
30mm
54mm
Junction box at
left end of screen
120mm
Limit Adjustments (Built-in Low Voltage Motors)
CE Approved
Junction box at
left end of screen
Multiple Station Control
Not CE Approved
Internal Screen Wiring
Blue-220v (Common)
Brown-220v (Down)
Black-220v (Up)
Internal Screen Wiring
Blue-220v (Common)
Brown-220v (Down)
Black-220v (Up)
Green/Yellow (Motor Ground)
Green/Yellow (Motor Ground)
www.draperinc.com
(765) 987-7999
Hot
Neutral
Neutral
L1
Please note: When ordering a motor with built-in Low Voltage Controller, if the case ships separate from the "guts," the case includes the 25'
cable and special low voltage switch.
Cap off with wire
nut & tape
① Connect the ILT switch to the
motor via the terminal blocks,
To Motor
Blue
Red
with
or via the modular port using
UD
C + Built-In
four conductor modular cable.
Black
p o
o 5V Low Voltage
w
Control
m DC
When using modular cable,
Blue
Red
n
m
switch
the cable connectors MUST
o
n
Black
NOT be crimped in reverse, as
Dashed wiring
Blue
Red
with standard telephone
POTS
by installer
P
PO
OT
TS
S
cable. (For Dry Contacts WirBlack
220v,
ing Diagram, see page 4.)
50 Hz.
Dashed wiring
② Set the slide switch to the
by installer
lower position. Press and hold
220v, 50 Hz.
To Motor
the DOWN button on the
with
Slide
switch to move the viewing
Built-In
Wiring Diagrams—220V Motor
surface to the desired lower Switch
Low Voltage
with Built-in Low Voltage Controller
limit. If the screen moves in
Back View
the opposite direction, release
Single Low Voltage Control Multiple Low Voltage Controls
FUNCTION
POSITION
the DOWN button and press and hold
down the STOP button for four seconds.
Set LOWER limit
DOWN
This will reverse the operation of the UP
Set UPPER limit
and DOWN switches.
UP
③ Move slider switch into center position.
CENTER Normal Operation
Wait a couple of seconds.
Dashed wiring
Please Note: If you move the slider switch from down to up in one moby electrician
Dashed wiring
Data Cable
by electrician
tion it sets the two limits in the same postion.
Data
Cables
④ Set the slide switch to the higher position. Move the viewing surface to the
desired upper limit by pressing and holding the UP button on the wall
switch.
Wall Switch,
⑤ Return the slide switch to the center position to return to normal operation.
RF or IR
⑥ To set the viewing surface to an alternate format position, move the viewing
Receiver,
Wall Switches,
or integrated
surface to the desired position and press the STOP button. Press and hold
RF or IR
control
system
Receivers,
the STOP button for at least three seconds to record the position.
or integrated
Please Note: Pressing and releasing the UP button on the switch will move
To 220V Line
control systems
To 220V Line
the screen to its upper limit. Pressing and releasing the DOWN button will
move the screen to its lower limit.
While the motor is in motion, pressing the STOP button for less than two
*These wiring diagrams are for Access screens with motor on audience
seconds will stop the viewing surface at its present position.
left (standard), and fabric unrolling from the back of the roller (standard).
Once the motor is stopped, pressing the STOP button will move the viewing surface to its alternate format position.
Pressing and holding the STOP button, when the motor is at rest or in motion, for at least three seconds will record a new alternate format position.
220V Access by Draper
page 4 of 4
Wiring Diagrams (continued)
ILT Switch-to-Motor—Dry Contacts or Data Cable connection
Please Note: This Splitter/
Jack is located inside the junction box of your Access XL
screen.
Motor Data Cable
plugged in here
Back of wall switch.
UD
P O
W
N
C 5V
O
M
M
O
N
Please Note: Although both
Dry Contact and Data Cable
connections are shown, you
should only use one connection type per motor.
Data Cables to switches or
to additional motors can
be plugged into any of the
three open jacks. If this is a
"Case First, Screen Later"
installation, plug the motor
cable into the jack indicated
in the drawing.
UP 5V COM DWN
External Low Voltage and Wireless
MC1
Internal Screen Wiring
Internal Screen Wiring
White/Blue (Common)
Red 110/Black 220 (Up)
Black 110/Brown 220 (Down)
Green/Yellow
(Motor Ground)
White or Blue-Common to screen & 110/220V AC Neutral
Red-to screen (directional)
Brown-to screen (directional)
Yellow-to 110/220V AC-Hot
Black-to 110/220V AC-Hot
Green/Yellow (Ground)
Dashed wiring by electrician
Low voltage wiring by others
Eye Port for IR Eye, RF Receiver or LED
Wall Switch. For more than one of
these, a splitter is required.
3 Button Wall Switch
DOWN - Black
COM - White
UP - Red
White or Blue-Common
Red-to Screen (directional)
Black-to Screen (directional)
Brown-Hot to AC
Green/Yellow-Ground
Program LED
Low Voltage Wiring by others
AC Wiring by electrician
Fuse
To
110/220V
Line
RS232 Data FROM Control System
RS232 Data TO Control System
Signal Ground & Manual Switch Common
Manual Switch Down
Manual Switch Up
STOP
STOP
Location of key
operated on-off
switch if furnished
Location of key
operated on-off
Eye Port for IR Eye. For RF Receiver or LED
switch if furnished
Wall Switch, a Splitter and a Power Supply
is required. Plug RF Receiver or LED Wall
Switch and Power Supply into splitter, then
run cable from Splitter to MC1 Eye Port.
To AC Line
MC1
Control
Switches
24v DC
Aux Port for connecting additional LVC-III
modules (up to six total can be linkedconnect from Aux to Eye).
White/Blue (Common)
Red 110/Black 220 (Up)
Black 110/Brown 220 (Down)
Green 110V/
Green/Yellow 220V
(Motor Ground)
See separate Serial Communication-RS232 Instruction sheet for enabling
RS232 with the MC1.
Built-In VIC-12*
Built-In VIC-115*
115 Volt Relay
12 Volt (VIC-12) or 6 Volt (VIC-6) Relay
Ring Terminal on each Ground Wire
with Star Washer screwed to Spine
:: : :
Wire soldered to terminal
Wire connected with Quick Disconnect
HSG. Cap
Blie
Ground
#2 Up
#1 Down
Common
220 VAC
Screen Motor
Jacketed Motor Cable
Blue
Black
Brown
: : ::
Green/
Yellow
Black
Brown
HSG. Plug
Black
3
1
Green/Yellow
Jacketed Motor Cable
Green/
Yellow
7
5
Blue Lead
220 VAC
Screen Motor
Black Lead
HSG. Cap
HSG. Plug
Blue
Blue
Black
Green/Yellow
Orange (+)
Brown (-)
Black
Brown
6
4
2
: : ::
Brown
Ground
#2 Up
#1 Down
Common
: : ::
Black
8
Green/Yellow
: : ::
Green
Yellow
14 13
9 :: : :
5 :: : :
1 :: : :
: : ::
Ring Terminal on ground wire
riveted to J-Box with Star Washer
:: : :
Wire connected with Quick Disconnect
*These wiring diagrams are for Access screens with motor on audience left (standard), and fabric unrolling from the back of the roller (standard).
Mounting Bracket Dimensions
9.5
mm
35
mm
12.7
mm
R 6.4
3.2 mm
mm
38
mm
8
mm
4.8
mm
28.6
mm
6.4
mm
R3.2
mm
4.8
mm
114
mm
8
mm
197
mm
www.draperinc.com
32
mm
122.2
mm
228.6
mm
(765) 987-7999
6.4
mm
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement