Ice RS26 Operator's & Parts Manual

Ice RS26 is an intelligent cleaning equipment designed for commercial use. It excels in scrubbing hard floors in indoor environments. Equipped with a solution tank, hose fill port, and squeegee assembly, this machine delivers efficient cleaning results. The operator enjoys a comfortable ride on the seat while controlling the machine with the steering wheel. It also features an LED work light for enhanced visibility, adjustable detergent dosage, and solution flow to meet various cleaning requirements.

PDF

Document

www.icecompanies.com

Operator & Parts Manual

RS26

RS28

RS32

8300004

REV.04 (03-2017)

INTELLIGENT CLEANING EQUIPMENT

OPERATOR MANUAL

Read opeRatoR manual caRefully!

IMPORTANT: To ensure full warranty protection, please fill out & return your warranty card.

Please fill out at time of installation for future reference.

Model No.

Serial No.

Machine Options

Sales Rep.

Sales Rep. Phone No.

Customer ID Number

Installation Date

HOW TO ORDER PARTS

Only use ICE Company supplied or equivalent parts. Parts and supplies may be ordered online,by phone, by fax or by mail.

1. Identify the machine model.

2. Identify the machine serial number from the data label.

3. Ensure the proper serial number is used from the parts list.

4. Identify the part number and quantity.

Do not order by page or reference numbers.

5. Provide your name, company name, customer ID number,billing and shipping address,

phone number and purchase order number.

PROTECT THE ENVIRONMENT

Please dispose of packaging materials,old machine components such as batteries, hazardous fluids, including antifreeze and oil, in an environmentally safe way according to local waste disposal regulations.

Always remember to recycle.

Ice company limited

XiangShi Road LiaoBu DongGuan GuangDong China

Tel: 0769 - 81869000

Fax:0769 - 81863000

Specifications and parts are subject to change without notice.

ICE RS26 / RS28 / RS32

OPERATOR MANUAL

TABLE OF CONTENTS

SAFETY PRECAUTIONS......................................................................................................4

MACHINE COMPONENTS................................................................................................5-6

MACHINE SETUP & INSTALLATION....................................................................................7

MACHINE OPERATION........................................................................................................8

WHILE OPERATING MACHINE............................................................................................9

TANK DRAINING.................................................................................................................10

BATTERY CHARGING........................................................................................................10

PREVENTATIVE MAINTENANCE.......................................................................................11

FAULT CODE AND ELIMINATE..........................................................................................12

TECHNICAL SPECIFICATION............................................................................................13

PARTS LIST..................................................................................................................14-39

WEAR AND TEAR PARTS...............................................................................................40

WIRING DIAGRAM.............................................................................................................41

3 ICE RS26 / RS28 / RS32

OPERATOR MANUAL

Safety pRecautIonS

- Avoid any contact with battery acid

- Avoid moving parts. Do not wear loose fitting

clothing while servicing machine.

This machine is intended for commercial use. It is designed exclusively to scrub hard floors in an indoor environment and is not constructed for any other use. Only use recommended accessories.

all operators shall read, understand and exercise the following safety precautions:

WaRnInG: Batteries emit hydrogen gas. Explosion or fire can result from hydrogen gas. Keep sparks and open flames away! Keep battery compartment open when charging.

1. Do not operate machine:

- Unless trained and authorized.

- Unless you have read and understand the

operators manual.

- In flammable or explosive areas.

- With brake disabled.

- If not in proper operating condition.

2. Before starting machine:

- Make sure all safety devices are in place

and operate properly.

- Check brakes and steering for proper

operation.

3. When using machine:

- Go slow on inclines and slippery surfaces.

- Follow all safety guidelines.

- Be very careful when using the machine in

reverse.

- Reduce speed when turning.

- Report and fix any damage to machine prior

to operating it.

- Never allow children to play on or

around.

4. Before leaving or servicing machine:

- Stop on level surface.

- Turn off machine.

5. When servicing machine:

- Read operators manual thoroughly prior to

operating or servicing this machine.

- Use manufacturer supplied or approved

replacement parts.

- Secure machine with wheel blocks prior to

jacking the machine up.

- Use approved jack or hoist to safely elevate

the machine.

- Disconnect batteries prior to working on

machine.

- Wear gloves when handling batteries or

battery cables.

WARNING: Flammable materials can cause an explosion or fire. Do not use flammable materials in tanks.

WARNING: Flammable materials or reactive metals can cause explosion or fire. do not pick up.

4 ICE RS26 / RS28 / RS32

OPERATOR MANUAL macHIne componentS

1. Solution tank

2. Hose fill port & Cap

3. Squeegee assembly

4. Wheels, 10 inch

5. Scrub head assembly

6. Side squeegee assembly

7. Watching window, on-

board battery charger

8. Brake pedal

9. Propel pedal

10. Front drive wheel

11. Operator seat

12. Steering wheel

13. LED light, work

14. Adjusting handle, seat

15. Off-board battery

charger receptacle

16. Detergent level watching

window

17. Warning light

18. Recovery tank cover

19. Recovery tank

20. Cup holder

21. Cap

22. Detergent bottle

23. Battery box

5 ICE RS26 / RS28 / RS32

OPERATOR MANUAL macHIne componentS

24. Directional switch

25. Main power key switch

26. Emergency stop switch

27. Warning light switch

28. Vacuum motor switch & indicator

29. Detergent dosage adjusting

buttons & indicator

30. Batteries meter

31. LED display screen

32. Fault indicator

33. Fault code

34. Fault message

35. Hour meter

36. Solution flow adjusting buttons &

indicator

37. Horn button

38. 1-Step switch & Indicator

39. Brush pressure adjusting button

& indicator

40. Drain hose, recovery tank

41. Drain hose, solution tank

42. Vacuum hose

ICE RS26 / RS28 / RS32

OPERATOR MANUAL

MACHINE SET UP & INSTALLATION uncRatInG macHIne

Be sure and check packing carton for any damage.

Immediately report any damage to carrier. Check the contents of package to ensure that the following items are included:

• Machine

• 4-6V Batteries

• Squeegee assembly

• 2-Pad drivers

3. Carefully place the batteries into the compartment as shown in figure below. Place the battery brace at the rear of the batteries.

NOTE: Do not drop the batteries into the compartment!

4. Connect battery cables to posts in numbered order as shown in drawing below.

NOTE: RED to POSITIVE and BLACK to

NEGATIVE.

1. Uncrate the wooden box, place the top board on the edge of pallet, lie in the front of the machine, as below shown.

5. Reinstall the Operator seat and the Battery box.

macHIne Set up

WaRnInG: do not operate machine unless you have read & understood this manual.

2. Install batteries.(see INSTALLING BATTERIES)

3. Turn on the Main power key switch (machine components, #25), make sure the Squeegee assembly (machine components, #3) and the

Scrub head assembly (machine components,

#5) is off the floor.

4. Sit in the Operator seat (machine components,

#11), hold the Steering wheel (machine components, #12), press the Propel pedal

(machine components, #9) and driving slowly the machine down from the slope.

InStallInG BatteRIeS

WaRnInG: Batteries emit hydrogen gas.

Explosion or fire can result from hydrogen gas.Keep sparks and open flames away! Keep battery compartment open when charging.

Recommended battery spec:

4-6V, 260AH@20HR deep cycle batteries.

Max. batteries dimensions :

300mm (L) X 180mm (W) X 290mm (H)

1. Turn the Main power key switch off.

2. Remove the Operator seat & the Battery box

(machine components, #23).

InStallInG BRuSHeS oR padS

1. Turn off the 1-Step switch (machine components, #38) and raise the Scrub head assembly off the floor, then stop machine on the level surface, remove the key and ensure the machine is turned off.

2. If using the pad driver, first attach the appropriate pad to the pad driver surface.

3. Align the pad driver or brush under the motor hub and push it upward to engage.

4. To remove the pad driver or brush, raise the scrub head and remove the Side squeegee assembly (machine components, #6), push the edge of brush downward.

ICE RS26 / RS28 / RS32

OPERATOR MANUAL mountInG tHe SQueeGee aSSemBly

1. Turn off the 1-Step switch and raise the

Squeegee assembly off the floor.

2. Mount the squeegee assembly to the squeegee pivot bracket. make sure the knobs are completely seated into the slots before securing knobs.

3. Connect the Vacuum hose (machine components, #42) to the squeegee assembly.

Loop the hose by using the hose clip provided.

4. Check the squeegee blades for proper adjustment.

macHIne opeRatIon

WaRnInG: do not operate machine unless you have read and understand this manual.

pRe-opeRatIon cHecKS

1. Check the tank cover seals for damage.

2. Drain the recovery tank, check the vacuum fan inlet filter, clean them if necessary.

3. Check the vacuum hose for debris or blockage.

4. Check the squeegees for damage, wear and for deflection adjustment.

5. Check whether Pad/Bruch is installed properly .

6. Check the brakes and steering for proper operation.

fIllInG tHe SolutIon tanK

The machine is equipped with a Hose fill-port

(machine components, #2) at the side of the machine, and a bucket fill-port located under the recovery tank.

NOTE: Before accessing the bucket fill-port make sure that the recovery tank is empty.

When filling the solution tank with a bucket, make sure that the bucket is clean. Do not use the same bucket for filling and draining the machine.

WARNING: Do not put any flammable materials into solution tank. this can cause an explosion or a fire. fIllInG tHe deteRGent Bottle

The machine is equipped with a 6 liters Detergent bottle (machine components, #22). Open the Cap

(machine components, #21) you can fill detergent, and watch the liquid level on the Detergent level watching window (machine components, #16).

The ratio of water and detergent is 0~5%, you can adjust this ratio via pressing the Detergent dosage adjusting buttons (machine components, #29).

NOTE: Only use recommended cleaning chemicals. Contact your janitorial supply distributor for recommendations on proper chemicals.

8 opeRatIon tHe macHIne

1. Sit in the Operator seat, adjusting the seat to comfortable place by pushing the Seat adjustment handle (machine components, #14).

NOTE: The machine will not travel unless the operator is sitting in the operator seat.

2. Turn on the machine.

Check the LED display screen (machine components, #31) , if there are fault codes

(machine components, #33) and the Fault indicator (machine components, #32) is blink, please Do Not operation the machine unless the faults have been eliminated (please see FAULT

CODES AND ELIMINATE section).

3. Select the preferred settings by pressing the

Brush pressure adjusting buttons (machine components, #39) , Solution flow adjusting buttons (machine components, #36) and

Detergent dosage adjusting buttons.

NOTE: Use the minimal pressure and flow as possible.

4. Turn on the 1-Step switch, the Scrub head assembly and the Squeegee assembly will lower down automatically, all the presetting functions will turn on.

5. The machine can scrub in both forward and backward, place the Directional switch (machine components, #24) in the forward direction is to move forward, backward is to move backward.

The horn will sound and the squeegee will raise automatically (the vacuum motor will turn off after a short delay) when drive machine backwards. This is to prevents damaging the squeegee.

NOTE: Go slow when drive machine backwards.

ICE RS26 / RS28 / RS32

OPERATOR MANUAL

6. Press the Propel pedal, the machine start scrubbing, the speed can be adjusted by controlling the force of foot stepping, light is slow, heavy is fast.

NOTE: Go slow on inclines and slippery surfaces.

7. To stop scrubbing, turn off the 1-Step switch, the scrub head will raise automatically, the squeegee will also raise after a short delay (the vacuum indicator flashing), please keep moving until the dirty water is picked up, and then release the propel pedal and stop scrubbing.

8. Turn off the machine.

BRaKe deVIce

The machine is drived by the Front drive wheel

(machine components, #10), that is equipped with a brake device. When you release the Propel pedal, the machine will stop travel, the park brake will engage after a short delay.

The machine is equipped with a Brake pedal

(machine components, #8), that can be used to control the machine if quicker stopping is needed or if operating on an incline. emeRGency Stop Button

The machine is equipped with an Emergency stop button (machine components, #26), please push it if an emergency, that will shut off all power of machine and brake immediately.

To restart the machine, please reset the

Emergency stop button, and turn off the Main power key switch, then turn on key switch.

NOTE: Please hold the steering wheel when emergency stop.

WHIle opeRatInG macHIne

WaRnInG: fire or explosion Hazard. do

Not Pick Up Flammable Materials Or Reactive metals.

1. Go slow on inclines and slippery surfaces, go slow when turn and reverse. Do not operate the machine on inclines that exceed 7% (4°).

2. Drive machine in a straight path as possible, avoid turning the Steering wheel too sharply when machine is in motion. avoid sudden turns except emergencies.

3. Do not keep the machine in the same position with pad / brush spinning, keep the machine moving to prevent damage to floor finish.

4. If the squeegee assembly leaves streaks on the floor, raise the squeegee off the floor and wipe the blades down with a damp cloth. Pre-sweep the area to prevent leaving streaks on the floor.

5. To obtain the optimum cleaning performance, you can adjust the brush pressure, solution flow and detergent dosage as your required. If poor picking up water performance is observed, please stop scrubbing and check the squeegee blade, adjust or replace if necessary.

6. If the dirty water path exceed the width of squeegee, please adjust the side squeegee assembly.

7. Pour a recommended defoamer into the recovery tank if excessive foam appears.

WaRnInG: the foam do not activate water level switch, excessive foam may result in vacuum motor damage.

8. Press the Horn button (machine components,

#37) to alert if necessary.

9. The machine is equipped with a Warning light

(machine components, #17), you can select turn

ON or OFF by the Warning light switch (machine components, #27).

10. If there is a fault code F10 (Batt low) on the

LED display screen, the machine will stop scrubbing and alarm, please drive the machine to charging.

11. If there is a fault code F08 (Rec Tank Full) on the LED display screen, the vacuum motor will stop working and alarm, please drive the machine to drain water.

If there is a fault code F09 (Soln Tank Empty) on the LED display screen, the Detergent system will stop working and alarm, please fill the solution tank.

12. If there are other fault codes on the LED display screen, please turn off the machine, eliminate the fault (please see FAULT CODES

AND ELIMINATE section), then restart machine.

13. For heavily soiled areas, please use DOUBLE

SCRUBBING mode.

The first time: Turn on the 1-Step switch, then press the Vacuum motor switch (machine components, #28), its indicator will turn off and the squeegee will raise automatically, then start to scrubbing this areas without picking up water.

The second time: turn on the Vacuum motor switch, the squeegee will lower down automatically, and then start to scrubbing and picking up water.

14. If you only want to pick up water needn't scrubbing, Turn on the Vacuum motor switch

(squeegee will lower down) and turn off the

1-Step switch (if it is ON), the scrub head will raise and then start to working.

9 ICE RS26 / RS28 / RS32

OPERATOR MANUAL tanK dRaInInG dRaInInG tHe RecoVeRy tanK

Any time scrubbing is completed, or when refilling solution tank, the recovery tank should be drained and cleaned.

WaRnInG: If the recovery tank is not drained when the solution tank has been refilled, foam or water may enter the float shutoff screen and cause damage to the vacuum motor.

1. While holding the Recovery tank drain hose

(machine components, #40) upward, remove the cap and lower hose to drain.

2. Open the Recovery tank cover (machine components, #18) and rinse out the tank. Use a rag to remove any excess dirt. Clean the vacuum fan inlet filter located in the recovery tank .

dRaInInG tHe SolutIon tanK

Any time scrubbing operation is completed, the solution tank should be drained and cleaned.

1. While holding the Solution tank drain hose

(machine components, #41) upward, remove the cap and lower hose to drain.

2. Rinse the solution tank with clean water after every use. This will help prevent chemical buildup and clogging of the solution lines.

BatteRy cHaRGInG on-BoaRd BatteRy cHaRGeR

As standard configuration, the machine is equiped with the On-board battery charger. The settings of On-board battery charger had been set for the recommended batteries type.

WaRnInG: The On-board battery charger setting's change are to be completed by authorized service centers only. Failure to properly set will result in the batteries or charger damage.

1. Transport the machine to a well ventilated area.

2. Turn the machine off.

3. If charging wet (lead acid) batteries check the fluid level before charging.

4. Prop up the Operator seat by the support stand for ventilation.

5. Connect the charger's AC power supply cord to a properly grounded receptable.

6. The charger will automatically begin to charge, you can watching the charging status on the window (machine components, #7), once the charging cycle begins, the indicator lights will progress from red, yellow to green. when the green indicator light comes on, the charging cycle is done. Unplug the charger cord.

NOTE: The machine will can not operate when charging. pReVentatIVe maIntenance

WaRnInG: fire or explosion Hazard.

Batteries emit Hydrogen Gas. Keep Sparks and open flame away. Keep Battery compartment propped open When charging.

Use only apprved chargers with the following specifications:

• automatic shut off circuit

• deep cycle charging

• output current of 20-30 amps

• output voltage of 24 volts

WaRnInG: Before performing any maintenance on the machine, be sure that the power is turned off, or the batteries are disconnected!

WARING: Repairs are to be completed by Authorized service centers only. Any repairs completed by unauthorized persons will avoid the warrenty.

daIly maIntenance

1. Remove pad driver/ brush and clean with approved cleaner.

2. Drain recovery and solution tanks completely and rinse out with clean water. Visually check the recovery tank for debris and clean out as necessary.

3. Raise the squeegee assembly off floor and wipe it down with a damp towel. Be sure to store the squeegee in the up position.

ICE RS26 / RS28 / RS32

OPERATOR MANUAL

4. Remove the vacuum fan inlet filter and rinse it out with clean water.

5. Clean machine with an approved cleaner and a damp towel.

6. Recharge the batteries.

7. Check the condition of the squeegee blade wiping edge, rotate blade if worn.

montHly maIntenance

1. Clean the battery tops to prevent corrosion.

2. Check for loose battery cable connections.

3. Inspect and clean the recovery tank cover seal.

Replace it if damaged.

4. Lubricate all grease points and pivot points with silicon spray and approved grease.

5. Check the machine for loose nuts and bolts.

6. Check the machine for leaks.

motoR maIntenance

1. Contact your local Distributor for any motor maintenance.

2. Motor should have the brushes checked every

250 hours. Brushes should be replaced when they are worn to a length of 10 mm or less.

BatteRy maIntenance

WaRnInG: Batteries emit hydrogen gas and an explosion o fire can result. Keep sparks and fire away from batteries at all times.

WARNING: Whenever servicing batteries, be sure to wear protective gloves. Avoid contact with battery acid at all times.

NOTE: For the best machine performance, keep batteries charged at all times. Do not let them sit in a discharged condition.

1. Always follow the battery charging directions as outlined in the BATTERY CHARGING section of this manual.

2. Keep battery tops and terminals free from corrosion. A strong solution of baking soda and water is the best way to keep the batteries corrosion free. DO NOT ALLOW THE BAKING

SODA / WATER SOLUTION TO ENTER THE

BATTERY CELLS.

3. Use a wire brush with the baking soda solution to properly clean the battery posts and connections.

4. Check battery connections for wear and loose terminals. replace if necessary.

macHIne StoRaGe

1. Always store the machine indoors.

2. Always store the machine in a dry area.

3. Always store the machine in its upright position.

4. Always store the machine with the pad driver/ brush raised off the floor.

5. Always store the machine with the squeegee assembly raised off the floor.

6. If storing in an area which may reach freezing temperatures, be sure to drain all fluids from the machine prior to storage. Any damage caused by freezing temperatures will not be covered by the warranty.

7. Drain the recovery tank.

8. Drain the solution tank of all fluid.

FAULT CODE & SOLUTION

The machine is equipped with a LED display screen (see Machine components, item # 31), the

LED screen will display the operating hours (see

Machine components, item # 35) and the battery level status (see Machine components, item # 30).

When the machine detects a fault, there will be a

Fault code (see Machine components, item #33)

& Fault message (see Machine components, item

#34) display on the LED screen, and the Fault indicator (see Machine components, item #32) will flash continuously, accompany an audible alarm

Occasionally.

Once fault occuring, please DO NOT continue operate the machine unless the fault are eliminated.

Turn off the machine, then to solve the fault, the fault code & message will be eliminated when machine restart.

If the fault is occurred frequently, or the fault can't be eliminated, please contact ICE service center.

Please refer to the below table to determine the fault cause and the solution.

ICE RS26 / RS28 / RS32

OPERATOR MANUAL

FAULT CODE & SOLUTION

FAULT

CODE

F01

F02

F03

F04

F05

F06

F07

F08

F09

F10

F11

FAULT MESSAGE

Seat Empty

Squeegee Actt O.L.

RE-START!

Bru Actt O.L.

RESTART!

Vac Mtr O.L.

RE-START!

Left Bru Mtr O.L.

RE-START!

Right Bru Mtr O.L.

RE-START!

Propel Mtr O.L.

RE-START!

RecTank Full

Soln Tank empty

Batt Low

Charge Batt

Batt Empty

Charge Batt NOW

FAULT CAUSE

Not sit in the seat

Squeegee lifting actuator is overload

Scrub head lifting actuator is overload

Vacuum motor overload

Left brush motor is overload

Right brush motor is overload

Propel motor overload

Recovery tank is full

Solution tank is empty

Battery is low

Battery is empty

F12 Brake Wiring Error Bad Brake wiring

F44

F45

F46

F47

F48

F21

F22

F23

F24

F13

F14

F16

F17

Release Foot pedal

Replace Brake Assy

Control Unit Overheat!

Wait

Replace Control Unit

Stepping the propel pedal when starting machine

Bad Brake assembly

Control Unit Overheat

Control Unit Fault

F18 Replace Accel Pedal Sensor Bad Accelerator pedal sensor

F19 Replace Brake pedal sensor Bad Accelerator pedal sensor

F20 Check Left Brush motor Bad left brush motor

Check Vac Mtr

Check Soln Solenoid

Replace Soln solenoid

Check Propel Motor

Bad Vacuum motor or wiring

Solution solenoid wiring fault

Bad Solution solenoid

Bad propel motor

F25

F40

F42

F43

Check Right Brush motor Bad right brush motor

Check Proximity Sw Proximity switch fault

Bad Control Unit Replace Control Unit

Turn Dead Sw Off

RE-START!

Replace Control Unit

Return Control Unit

Emergency stop button activated

Bad Control Unit Return Control Unit

Return Control Unit

SOLUTION

Sit in the operator seat

Turn off the machine,after a moment,

RE-START machine.

Drain the Recovery tank

Fill the solution tank

Charge the battery

Charge the battery NOW

Check the brake wiring

Release the propel pedal

Replace the brake assembly

Turn off the machine,after a moment,

RE-START machine

Replace the control unit

Replace accelerator pedal sensor

Check left brush motor/ wiring

Check the vacuum motor / Wiring

Check the wiring & Contactors

Replace the solution solenoid

Check the propel motor / Wiring

Check right brush motor/ wiring

Check the Proximity switch

Replace the control unit

Release emergency stop button and restart machine

Contact service center, Replace the

Control Unit

12 ICE RS26 / RS28 / RS32

OPERATOR MANUAL

MODEL

LENGTH

WIDTH (MACHINE WITH

SCRUB HEAD)

HEIGHT

WEIGHT

WEIGHT WITH BATTERIES

RECOVERY TANK CAPACITY tecHnIcal SpecIfIcatIonS

RS26 RS28

61.6 in / 1,565 mm

32 in / 815 mm 33.7 in / 855 mm

56.7 in / 1,440 mm

618 lbs / 280 Kg

880 lbs / 400 Kg

29 Gal / 110 L

RS32

37.4 in / 950 mm

640 lbs / 290 Kg

900 lbs / 410 Kg

SOLUTION TANK CAPACITY

SQUEEGEE WIDTH

CLEANING PATH WIDTH

PRODUCTIVITY RATE PER

HOUR (IN THEORY)

TRAVEL SPEED

(TRANSPORT)

MINIMUM AISLE TURN

PAD/BRUSH PRESSURE

SOLUTION FLOW

BatteRIeS

VOLTAGE

DRIVE WHEEL

BRUSH MOTOR

VACUUM MOTOR

VACUUM WATER LIFT (MAX)

RUN TIME PER CHARGE

DECIBEL RATING AT

OPERATOR'S EAR, INDOORS

GRADE LEVEL, MAX

33.8 in / 860 mm

29 Gal / 110 L

40 in / 1,030 mm

26 in / 650 mm

46, 300 ft

4,300 m 2

71 in / 1,800 mm

28 in / 710 mm

49, 500 ft 2

4,600 m 2

4 Mile / h

6.5 Km / h

32 in / 810 mm

55, 600 ft 2

5,200 m 2

75 in / 1,900 mm

80 lbs / 35 Kg

120 lbs / 55 Kg

160 lbs / 75 Kg

0 ~ 0.7 Gal / Min

0 ~ 2.7 L / Min

4 x 6V, 240AH@20Hr

24V DC

1.1 hp / 0.8 KW

(2) 0.6 hp / 0.45 KW, 210 RPM

0.6 hp / 0.45KW

70 in. H2O / 1780 mm. H2O

3~3.5 Hours

68 dB(A)

Scrubbing: 4°/7% Transporting (empty):10°/17.5%

ICE RS26 / RS28 / RS32

PARTS LIST

MAIN FRAME GROUP

14 ICE RS26 / RS28 / RS32

PARTS LIST

DIA

NO.

PART

NUMBER

1436025

8310150

6210131

1421510

1221512

8310120

1421824

1422821

1021825

8210118

8310708A

1421307

1211316

8310102

8310133

8310930A

8310931

1421409

1422411

1221412

8310119

1612605

MAIN FRAME GROUP

DESCRIPTION

MAIN FRAME, WELDED

RUBBER GROMMET

PERISTALTIC PUMP, KIT

TUBING, PUMP

FLAT WASHER, M4×∮9×0.8

LOCK WASHER M4

SCREW, PAN HEAD, M4×12

10" WHEEL, PU TIRE

BALL BEARING,6205-2RS

RETAINING RING, 25MM

WHEEL CAP

NYLON, CLAMP

FLAT WASHER, M5×∮10×1.0

SCREW, PAN HEAD, M5×12

BRACKET, STAND

FLAT WASHER, M8×∮24×2.0

LOCK WASHER M8

BOLT, HEX, M8×25

STATIC STRAP

HORN, 24VDC, KIT

PLAT WASHER, M3×∮7×0.5

SCREW, PAN HEAD, M3×16

REQ'D

15 ICE RS26 / RS28 / RS32

PARTS LIST

STEERING & DRIVE WHEEL GROUP

16 ICE RS26 / RS28 / RS32

PARTS LIST

DIA

NO.

PART

NUMBER

1113014

8310605

1654025

8310604

1534508

1123507

1421510

6210131

8310645

1421428

8310602

8310699A

8310608

1021825

1422821

1421816

8310609

1021060

1422026

1421030

8310601

1021820

1421824

8310640

8310431

8310603

8310650

8310611

8310612

8310613

8310618A

STEERING & DRIVE WHEEL GROUP

DESCRIPTION

LOCK NUT, M14

FLAT WASHER, M14×∮28×2.0

STEERING WHEEL

CUSHION WITH ICE LOGO

BELLOWS, SHAFT, STEERING

BOLT, HEX HEAD, M8×25

LOCK WASHER, M8

FLAT WASHER, M18×∮16×1.6

BEARING, FLANGE

SHAFT, STEERING WHEEL

KEY, 4.75×4.75×25.4

U-JOINT

SET SCREW, M5 ×8

LOCK NUT, M5

FLAT WASHER, M5×∮10×1.0

CLAMP, NYLON

BRACKET, FLANGE BEARING

BOLT, HEX HEAD, M10×60

LOCK WASHER, M10

FLAT WASHER, M10×∮30×2.5

SUPPORT BRACKET, STEERING

BOLT, HEX HEAD, M8×20

FLAT WASHER, M14×∮24×2.0

ACCELERATOR/ BRAKE PEDAL

HALL SENSOR WITH CABLE

STEER-CONTROL ASSY.

DRIVE WHEEL, 24VDC 800W

PU TIRE, DRIVER WHEEL

ARMATURE BRUSH

BRUSHES CONNECTION BOX

ELECTRICALLY RELEASED BRAKE

17 ICE RS26 / RS28 / RS32

REQ'D

PARTS LIST

SOLUTION TANK GROUP

18 ICE RS26 / RS28 / RS32

PARTS LIST

PART

NUMBER

8310101

1221512

1421510

8113009

1021820

1421824

8310139

8310151A

8310132

1222508

1512820

8310125

1021825

8310225

8310224

1962050

8011030

8310123

8310122

1421816

8310140

1422821

8310130

8310124

8310142

8310141

8310238A

DIA

NO.

SOLUTION TANK GROUP

DESCRIPTION

SOLUTION TANK

SCREW, PAN HEAD, M5×12

FLAT WASHER, M5×∮10×1.0

CLAMP, NYLON

BOLT, HEX HEAD, M8×20

FLAT WASHER, M8×∮24×2.0

PLATE

NON-SLIP MAT

FOOTREST PLATE

SCREW, M5×8

SCREW, HEX SOCKET, M8×20

FLAT WASHER, M8×∮16×1.6

JUNCTION PLATE

LOCK WASHER, M8

BRACKET, SOLUTION TANK MNTG

ELBOW, G1/2

NUT, M36

SEALING

SENSOR, SOLUTION LEVEL, KIT

CAP, SOLUTION TANK

BOLT, HEX HEAD, M8×25

SLEEVE, ∮8.1×∮12.7×7.8

ARM, RECOVERY TANK SUPPORT

CLAMP, 2 INCH

HOSE ASSEMBLY

ADAPTER, STRAINER ASSY

STRAINER ASSY

19 ICE RS26 / RS28 / RS32

REQ'D

PARTS LIST

RECOVERY TANK GROUP

20 ICE RS26 / RS28 / RS32

PARTS LIST

DIA

NO.

PART

NUMBER

8310238A

8310219

1022860

1123810

1021825

8310225

8310223

8310215

8310211

8310214

6210111

8011030

1962050

4010316

8310126

8113009

1221512

8310221

8310220

8310222

8310216

8310201

8310237

1021820

1421824

8310227

1513820

8310226

8310250

8012008

1421618

1321413

1221516

1421510

2310129

RECOVERY TANK GROUP

DESCRIPTION

SENSOR, SOLUTION LEVEL, KIT

RECOVERY TANK

FILTER, DUST

BOLT, HEX HEAD, M8×20

FLAT WASHER, M8×∮24×2.0

HINGE, WELDED

SCREW, HEX SOCKET, M8×20

HINGE, LEAF

DEBRIS COLLECTOR

BUSHING

FLAT WASHER, M6×∮18×1.6

SELF-TAPPING, ST4.8 x 13

SCREW, PAN HEAD, M5×16

FLAT WASHER, M5×∮10×1.0

CLAMP, HOSE

DRAIN HOSE

CLAMP, 2 INCH

ICE LOGO

HINGE ASSY.

CLAMP, NYLON

SCREW, PAN HEAD, M5×12

SPACER

COMPRESSION SPRING

FLAT WASHER, LARGE

COVER, SOLUTION TANK

SEALING STRIP

BOLT, HEX HEAD, M8×60

LOCK NUT, M8

BOLT, HEX HEAD, M8×25

SLEEVE, ∮8.1×∮12.7×7.8

ARM, RECOVERY TANK SUPPORT

BRACKET, RECOVERY TANK SUPPORT

BRACKET, SUPPORT

SPACER, RUBBER

REQ'D

ICE RS26 / RS28 / RS32

PARTS LIST

RECOVERY TANK COVER GROUP

22 ICE RS26 / RS28 / RS32

PARTS LIST

DIA

NO.

PART

NUMBER

1221512

1421510

8310138A

1123507

8310241

8310202

8310236

8310235

8310229

1021610

1422616

1021820

1421824

8310203

8310208

8310209

8310234

1311316

8310206

8310230

1021620

8310232

1421618

1022600

8310228

8310231

1021616

8310260

8132006

8310207

1962050

1123608

1421612

8310204

8310205

RECOVERY TANK COVER GROUP

DESCRIPTION

SCREW, PAN HEAD, M5×12

FLAT WASHER, M5×∮10×1.0

CAUTION LIGHT, KIT

LOCK NUT, M5

PLATE, CATUION LIGHT

RECOVERY TANK COVER

AMETK VACUUM MOTOR, 3 STAGE, KIT

CARBON BRUSH FOR VACUUM MOTOR

VACUUM HOSE

CLAMP, 2 INCH

LOCK NUT, M6

FLAT WASHER, M6×∮12×1.6

ADAPTER, VACUUM HOSE

GASKET, ADAPTER

GASKET, DUST FILTER

BOLT, HEX HEAD, M6×20

BRACKET

FLAT WASHER, M6×∮18×1.6

BOLT, HEX HEAD, M6×100

SUPPORT, RECOVERY TANK COVER

SLEEVE, ∮6.4×∮9.5×4

BOLT, HEX HEAD, M6×16

SPACER, NYLON

SLEEVE, ∮6.4×∮9.5×8

SEALING STRIP

BOLT, HEX HEAD, M6×10

LOCK WASHER, M6

BOLT, HEX HEAD, M8×20

FLAT WASHER, M8×∮24×2.0

PLATE, VACCUM MOTOR MNTG

ISOLATER, M6

BRACKET, VACCUM MOTOR

INSULATION

SCREW, SELF-TAPPING, ST4.8×16

SEAL, FAN

REQ'D

ICE RS26 / RS28 / RS32

PARTS LIST

CONTROL PANEL GROUP

24 ICE RS26 / RS28 / RS32

PARTS LIST

DIA

NO.

PART

NUMBER

1221512

1421510

8311703

8311702

8310712

8310773

8310775

1221306

8310701

1421824

1422821

1021825

8310702

8310704

8312704

8310750

2010121

8310709

8310707

8310706A

1321110

1421409

8133610

8133601

1221520

8133602

4010316

8310711

CONTROL PANEL GROUP

DESCRIPTION

SCREW, PAN HEAD, M5×12

FLAT WASHER, M5×∮10×1.0

DECAL, CONTROL PANEL

PLATE, CONTROL PANEL

GASKET, CONTROL PANEL

PCB, CONTROL PANEL (AGM / EN)

PCB, CONTROL PANEL (WET FLOODED / EN)

SCREW, PAN HEAD, M3×6

CONROL HOUSING

FLAT WASHER, M8×∮24×2.0

LOCK WASHER, M8

BOLT, HEX HEAD, M8×25

SCREW, SELF-TAPPING, ST3.5×10

FLAT WASHER, M4×∮9×0.8

LED LIGHT, KIT

BASE, LED LIGHT

SCREW, PAN HEAD, M5×20

COVER, LED LIGHT

ICE LOGO

GASKET, SWITCH PANEL

PLATE, SWITCH PANEL

DECAL, SWITCH PANEL, RS32

DECAL, SWITCH PANEL, RS28

DECAL, SWITCH PANEL, RS26

ICE LOGO, SMALL

ROCKER SWITCH

EMERGENCY STOP SWITCH

KEY SWITCH, KIT

25 ICE RS26 / RS28 / RS32

REQ'D

PARTS LIST

MAIN CONTROLLER GROUP

26 ICE RS26 / RS28 / RS32

PARTS LIST

PART

NUMBER

1021616

8310452

1421510

1221520

8310790

1423612

1023612

1422513

1221525

1434300

8310423

1421307

1211320

8310763

8112030

1123507

8210106A

1121505

1422616

1421618

8310480

8114705

8310422

8310133

8310740

8014068

8310450

1211330

8310425

1021825

1422821

1421828

1123305

DIA

NO.

CONTROLLER GROUP

DESCRIPTION

SCREW, HEX HEAD, M6×16

LOCK WASHER, M6

FLAT WASHER, M6×∮18×1.6

FUSE, 150A

INSULATOR

BRACKET, INSULATOR

RUBBER GROMMET

CIRCUIT BREAKER, 5A

CIRCUIT BREAKER, 10A

BRACKET, SCRUB HEAD LIFTING

SCREW, PAN HEAD, M3×30

BRACKET

BOLT, HEX HEAD, M8×25

LOCK WASHER, M8

FLAT WASHER, M8×∮28×2.5

LOCK NUT, M3

WASHER, TOOTH, M3

MICRO SWITCH

FLAT WASHER, M3×∮7×0.5

SCREW, PAN HEAD, M3×20

OFF BOARD CHARGER SOCKET

POWER CORD, BATTERY CHARGER, US

LOCK NUT, M5

ON BOARD BATTERY CHARGER, 25A

HEX NUT, M5

BRACKET, BATTERY CHARGER

FLAT WASHER, M5×∮10×1.0

SCREW, HEX HEAD, M5×20

MAIN CONTROLLER

FLAT WASHER M6× ∮ 12×1, COPPER

HEX BOLT M6 X 12, COPPER

LOCK WASHER,M5

SCREW, HEX HEAD, M5×25

REQ'D

ICE RS26 / RS28 / RS32

PARTS LIST

SEAT & DETERGENT SYSTEM GROUP

28 ICE RS26 / RS28 / RS32

PARTS LIST

PART

NUMBER

1221412

8133502

8133501

1123810

8310413

8117007

8310415

8310414

1421816

1021830

8310411

8310133

1512820

8310402K

1021616

1421618

8310418

8310419

1123608

8310460

8310463

8310464

8310461

8310462

1021820

1422821

1421828

8310465

8310421

DIA

NO.

SEAT & DETERGENT SYSTEM GROUP

DESCRIPTION

SCREW, HEX HEAD, M4×12

CLAMP

CARGO NET

LOCK NUT, M8

SUPPORT, SEAT

NYLON SPACER

TORSION SPRING

SLEEVE, ∮8.2×∮11×15

FLAT WASHER, M8×∮16×1.6

BOLT, HEX HEAD, M8×30

PLATE, SEAT MNTG

RUBBER GROMMET

SCREW, HEX SOCKET, M8×20

SEAT, KIT

SCREW, HEX HEAD, M6×16

FLAT WASHER, M6× ∮ 18×1.6

CUP HOLDER

BRACKET, CUP HOLDER

LOCK NUT, M6

SPACER

ADAPTOR, KEY

INSERT, LOCK

BOTTLE, DETERGENT

CAP, BOTTLE

BOLT, HEX HEAD, M8×20

LOCK WASHER, M8

FLAT WASHER, M8×∮28×2.5

BOX, DETERGENT BOTTLE

BRACKET

29 ICE RS26 / RS28 / RS32

REQ'D

PARTS LIST

BATTERY GROUP

30 ICE RS26 / RS28 / RS32

PARTS LIST

PART

NUMBER

8310401

1021820

1422821

1421824

8310131

8210105

8310135

8310407

8310136

8310736

8310737

8310733

8114751

8210141

1221412

8310406

8210114

1662316

8310404

1421409

8310403

DIA

NO.

BATTERY GROUP

DESCRIPTION

BOX, BATTERY

BOLT, HEX HEAD, M8×20

LOCK WASHER, M8

FLAT WASHER, M8×∮24×2.0

SUPPORT, BATTERY, REAR

BATTERY, 6V 230AH

TRAY, BATTERY

PLATE

SUPPORT, BATTERY, FRONT

BATTERY CONNECT CABLE, RED

BATTERY CONNECT CABLE, BLACK

JACKET, BATTERY TERMINAL,BLACK

BATTERY CONNECT CABLE, BLACK

SCREW, PAN HEAD, M4×12

COVER

RIVET, 3.2×16

HINGE ASSEMBLY

FLAT WASHER, M4×∮9×0.8

COVER

REQ'D

31 ICE RS26 / RS28 / RS32

PARTS LIST

SCRUB HEAD LIFTING GROUP

32 ICE RS26 / RS28 / RS32

PARTS LIST

PART

NUMBER

8310320

8210301

8310311

8310312

8210309

8310303A

8310305

8310314

8310313

1032090

1421030

8310304

1421020

8310307

1123012

8310144

8310118

1011025

8310306

8310308

DIA

NO.

SCRUB HEAD LIFTING GROUP

DESCRIPTION

PIN, COTTER

PIN, ∮9.5×38

PIN, ∮16×150

PIN, ∮16×57

PIN, COTTER

LINEAR ACTUATOR, KIT

PLATE, ARM, SCRUB HEAD LIFTING

FLAT WASHER, LARGE

PIN, ∮12×90

BOLT, HEX HEAD, M10×90

FLAT WASHER, M10×∮30×2.5

BRACKET, SCRUB HEAD LIFTING

FLAT WASHER, M10×∮20×2

BUSHING, FLANGE

LOCK NUT, M10

SLEEVE, ∮16×∮18.6×25.4

ARM, SCRUB HEAD LIFTING

BOLT, HEX HEAD, M10×25

SLEEVE, ∮10.5×∮18.5×34

SPRING

REQ'D

33 ICE RS26 / RS28 / RS32

PARTS LIST

SCRUB HEAD GROUP

34 ICE RS26 / RS28 / RS32

PARTS LIST

DIA

NO.

PART

NUMBER

8310399

8210804

8210805

1421828

1422821

9000004

9050013

9050014

9050016

9000003

9040013

9040014

9040016

8311358

8312358

8310358

8311359

8312359

8310359

1421618

8310316

1655025

8311301

8312301

8310301

1021830

1421824

8310356

8210532

1123810

8210531

8310355

8310365

8310366

8310357

1421020

1422010

1023010

1021616

8310361

1021840

8310362

8115404

1022800

8310354

8310351

8310353

SCRUB HEAD GROUP

DESCRIPTION

BRUSH MOTOR, 24VDC 450W, KIT

CARBON BRUSH

KEY, 5×5×25

SCRUB HEAD HOUSING, RS26

SCRUB HEAD HOUSING, RS28

SCRUB HEAD HOUSING, RS32

BOLT, HEX HEAD, M8×30

FLAT WASHER, M8×∮24×2.0

BRACKET, LEFT

KNOB, M10

LOCK NUT, M8

KNOB, M6

CLAMP, SIDE SKIRT

BLADE, SIDE SKIRT, LINATEX

BLADE, SIDE SKIRT, PU (OPTION)

BRACKET, SIDE SKIRT, LEFT

FLAT WASHER, M10×∮20×2.0

LOCK NUT, 3/8

BOLT, HEX HEAD, 3/8-16×1

SPACER

HUB, BRUSH DRIVE

FLAT WASHER, M8×∮28×3.0

LOCK WASHER, M8

CLUTCH, G-400S

BRUSH, 13 INCH, RS26

BRUSH, 14 INCH, RS28

BRUSH, 16 INCH, RS32

CENTER LOCK, #3

PAD DRIVER, 13 INCH, RS26

PAD DRIVER, 14 INCH, RS28

PAD DRIVER, 16 INCH, RS32

SKIRT, RS26

SKIRT, RS28

SKIRT, RS32

CLAMP, SKIRT, RS26

CLAMP, SKIRT, RS28

CLAMP, SKIRT, RS32

FLAT WASHER, M6×∮18×1.6

BOLT, HEX HEAD, M6×16

BRACKET, PROTECTIVE WHEEL

BOLT, HEX HEAD, M8×40

PROTECTIVE WHEEL

SLEEVE, ∮8×∮12.7×12.7

BOLT, HEX HEAD, M8×100

KNOB, M10

BRACKET, SIDE SKIRT, RIGHT

BRACKET, RIGHT

REQ'D

ICE RS26 / RS28 / RS32

PARTS LIST

SQUEEGEE GROUP / 水刮组件

36 ICE RS26 / RS28 / RS32

PARTS LIST

DIA

NO.

PART

NUMBER

8310506

8310562

8311560

8310560

8311534

8310534

8311544

8310544

1021835

8210518

8115404

8116009

1421824

1123810

8210309

8310311

8310508

8310509

1031212

1421030

1021060

8310507

8118624

8118623

1123507

8311514

8310514

8311531

8310531

8311541

8310541

8311561

8310561

8311562

8310590A

8310320

1121008

8310503

8310240

1123115

8310550

8310501

8310504

8310505

8210525

1221575

SQUEEGEE GROUP / 水刮组件

DESCRIPTION

PIN, ∮10×45

LINEAR, ACTUATOR, KIT

PIN, COTTER

HEX NUT, M10

BRACKET, SQUEEGEE

VACUUM HOSE

LOCK NUT, M12

CASTER, 2 INCH

COMPRESSION SPRING,

ARM, SQGE LIFTING

FLEX BUSHING, TPU

SHORT CLAMP ASSEMBLY

SCREW, PAN HEAD, M5×75

SHAFT

SPACER

LOCK NUT, M5

CLAMP ASSEMBLY, RS26

CLAMP ASSEMBLY, RS28 / RS32

REAR BLADE, LINATEX, RS26

REAR BLADE, LINATEX, RS28 / RS32

REAR BLADE, PU, RS26, OPTION

REAR BLADE, PU, RS28 / RS32, OPTION

SQUEEGEE HOSING, RS26

SQUEEGEE HOSING, RS28 / RS32

RETAINER, SQUEEGEE, RS26

RETAINER, SQUEEGEE, RS28 / RS32

SQUEEGEE ASSEMBLY, RS26

SQUEEGEE ASSEMBLY, RS28 / RS32

FRONT BLADE, LINATEX, RS26

FRONT BLADE, LINATEX, RS28 / RS32

FRONT BLADE, PU, RS26, OPTION

FRONT BLADE, PU, RS28/ RS32, OPTION

BOLT, HEX HEAD, M8×35

KNOB, M8

SLEEVE, ∮ 8× ∮ 12.7×12.7

PROTECTIVE WHEEL

FLAT WASHER, M8× ∮ 24×2

LOCK NUT, M8

PIN, COTTER

PIN, ∮ 16×150

PIN, ∮ 12×100

EXTENSION SPRING

BOLT, HEX HEAD, M12×120

FLAT WASHER, M10× ∮ 30×2.5

BOLT, HEX HEAD, M10×60

ADAPTER

REQ'D

ICE RS26 / RS28 / RS32

PARTS LIST

SOLUTION & DETERGENT SYSTEM

38 ICE RS26 / RS28 / RS32

PARTS LIST

PART

NUMBER

8310124

1962025

8310901

8310375

8310371

1421510

1422513

1221512

8310902

8310903

8310374

8310904

8310905

8310930A

1914080

8310910

8310467

8310909

8310466

DIA

NO.

SOLUTION & DETERGENT SYSTEM

DESCRIPTION

ELBOW, G1/2

CLAMP 16-25MM

TUBING, ID=16MM L=500MM

ELBOW, CHEMICAL CONNECTOR

SOLENOID VALVE, 24VDC

FLAT WASHER, M5×∮10×1.0

LOCK WASHER M5

SCREW, PAN HEAD, M5×12

TUBING, ID=16MM L=40MM

TUBING, ID=12MM L=175MM

FITTING, PLASTIC

TUBING, ID=12MM L=210MM

TUBING, ID=4MM L=330MM

DETERGENT PUMP, KIT

TIE, 3×80MM

TUBING, ID=4MM L=100MM

FITTING

TUBING, ID=4MM L=30MM

ONE WAY VALVE

REQ'D

39 ICE RS26 / RS28 / RS32

WEAR AND TEAR PARTS

DIA

NO.

PART

NUMBER

8310119

8116009

8310362

8311531

8310531

8311534

8310534

9050013

9050014

9050016

9040013

9040014

9040016

WEAR AND TEAR PARTS

DESCRIPTION

10" WHEEL, PU TIRE

PROTECTIVE WHEEL

REAR BLADE, LINATEX, RS26

REAR BLADE, LINATEX, RS28 / RS32

FRONT BLADE, LINATEX, RS26

FRONT BLADE, LINATEX, RS28 / RS32

BRUSH, 13 INCH, RS26

BRUSH, 14 INCH, RS28

BRUSH, 16 INCH, RS32

PAD DRIVER, 13 INCH, RS26

PAD DRIVER, 14 INCH, RS28

PAD DRIVER, 16 INCH, RS32

REQ'D

40 ICE RS26 / RS28 / RS32

WIRING DIAGRAM

ICE RS26 / RS28 / RS32 41

Hello! I am an AI chatbot specifically trained to assist you with the Ice RS26 Operation manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!