MTX3 Owner`s Manual

MTX3 Owner`s Manual
Owner’s Manual
EN
Contents
Getting Started................................................................................................................6
Included items (please check) ................................................................................................ 6
Firmware versions................................................................................................................... 6
Precautions for rackmounting.................................................................................................. 6
Introducing the MTX3.....................................................................................................7
Features.................................................................................................................................. 7
About MTX Editor ................................................................................................................... 7
Using the PDF manual............................................................................................................ 7
Controls and Connectors ..............................................................................................8
Front Panel.............................................................................................................................. 8
Rear Panel .............................................................................................................................. 9
Euroblock plug connection..............................................................................................11
Quick Guide ..................................................................................................................13
Preparations.......................................................................................................................... 13
On-site work (Installation and wiring) .................................................................................... 14
On-site work (Settings in MTX Editor)................................................................................... 15
Various Procedures ......................................................................................................16
Recalling (switching) presets ................................................................................................ 16
Switching presets from the MTX3 .................................................................................. 16
Setting the clock.................................................................................................................... 16
Using the scheduler .............................................................................................................. 16
Connecting via the [GPI] connector ...................................................................................... 17
Using the MTX3 to play audio files saved on an SD memory card ....................................... 18
Inserting an SD memory card........................................................................................ 18
Removing the SD memory card..................................................................................... 18
Initializing the MTX3 ............................................................................................................. 18
Appendix .......................................................................................................................20
Troubleshooting..................................................................................................................... 20
Alert list ................................................................................................................................. 21
Specifications........................................................................................................................ 22
Input/Output Characteristics ................................................................................................. 23
Dimensions ........................................................................................................................... 23
Block Diagram....................................................................................................................... 24
Index ..................................................................................................................................... 25
2 MTX3 Owner’s Manual
SPECIAL MESSAGE SECTION
This product utilizes batteries or an external power supply
(adapter). DO NOT connect this product to any power supply or
adapter other than one described in the manual, on the name
plate, or specifically recommended by Yamaha.
WARNING: Do not place this product in a position where
anyone could walk on, trip over ,or roll anything over power or
connecting cords of any kind. The use of an extension cord is
not recommended! If you must use an extension cord, the minimum wire size for a 25’ cord (or less ) is 18 AWG. NOTE: The
smaller the AWG number, the larger the current handling
capacity. For longer extension cords, consult a local electrician.
This product should be used only with the components supplied or; a cart, rack, or stand that is recommended by
Yamaha. If a cart, etc., is used, please observe all safety markings and instructions that accompany the accessory product.
SPECIFICATIONS SUBJECT TO CHANGE:
The information contained in this manual is believed to be correct at the time of printing. However, Yamaha reserves the right
to change or modify any of the specifications without notice or
obligation to update existing units.
Battery Notice:
This product MAY contain a small non-rechargeable battery
which (if applicable) is soldered in place. The average life span
of this type of battery is approximately five years. When
replacement becomes necessary, contact a qualified service
representative to perform the replacement.
This product may also use “household” type batteries. Some of
these may be rechargeable. Make sure that the battery being
charged is a rechargeable type and that the charger is
intended for the battery being charged.
When installing batteries, never mix old batteries with new
ones, and never mix different types of batteries. Batteries
MUST be installed correctly. Mismatches or incorrect installation may result in overheating and battery case rupture.
Warning:
Do not attempt to disassemble, or incinerate any battery. Keep
all batteries away from children. Dispose of used batteries
promptly and as regulated by the laws in your area. Note:
Check with any retailer of household type batteries in your area
for battery disposal information.
This product, either alone or in combination with an amplifier
and headphones or speaker/s, may be capable of producing
sound levels that could cause permanent hearing loss. DO
NOT operate for long periods of time at a high volume level or
at a level that is uncomfortable. If you experience any hearing
loss or ringing in the ears, you should consult an audiologist.
IMPORTANT: The louder the sound, the shorter the time
period before damage occurs.
Disposal Notice:
Should this product become damaged beyond repair, or for
some reason its useful life is considered to be at an end,
please observe all local, state, and federal regulations that
relate to the disposal of products that contain lead, batteries,
plastics, etc. If your dealer is unable to assist you, please contact Yamaha directly.
Some Yamaha products may have benches and / or accessory
mounting fixtures that are either supplied with the product or as
optional accessories. Some of these items are designed to be
dealer assembled or installed. Please make sure that benches
are stable and any optional fixtures (where applicable) are well
secured BEFORE using.
Benches supplied by Yamaha are designed for seating only. No
other uses are recommended.
NAME PLATE LOCATION:
The name plate is located on the top panel of the product. The
name plate lists the product’s model number, power requirements, and other information. The serial number is located on
the top panel. Please record the model number, serial number,
and date of purchase in the spaces provided below, and keep
this manual as a permanent record of your purchase.
NOTICE:
Service charges incurred due to a lack of knowledge relating to
how a function or effect works (when the unit is operating as
designed) are not covered by the manufacturer’s warranty, and
are therefore the owners responsibility. Please study this manual carefully and consult your dealer before requesting service.
Model
ENVIRONMENTAL ISSUES:
Yamaha strives to produce products that are both user safe
and environmentally friendly. We sincerely believe that our
products and the production methods used to produce them,
meet these goals. In keeping with both the letter and the spirit
of the law, we want you to be aware of the following:
92-BP (others)
Serial No.
Purchase Date
PLEASE KEEP THIS MANUAL
MTX3
Owner’s Manual
3
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your
authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded
cables. Cable/s supplied with this product MUST be used.
Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in
the USA.
3. NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15 for
Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your
use of this product in a residential environment will not result
in harmful interference with other electronic devices. This
equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in the
users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regu-
lations does not guarantee that interference will not occur in
all installations. If this product is found to be the source of
interference, which can be determined by turning the unit
“OFF” and “ON”, please try to eliminate the problem by using
one of the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate
retailer, please contact Yamaha Corporation of America,
Electronic Service Division, 6600 Orangethorpe Ave, Buena
Park, CA90620
The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
WARNING: THIS APPARATUS MUST BE EARTHED IMPORTANT. The wires in this mains lead are coloured in accordance
with the following code:
GREEN-AND-YELLOW : EARTH
BLUE
: NEUTRAL
BROWN
: LIVE
As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying the
terminals in your plug proceed as follows:
The wire which is coloured GREEN-and-YELLOW must be
connected to the terminal in the plug which is marked by the
letter E or by the safety earth symbol
or colored GREEN or
GREEN-and-YELLOW.
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.
(class B)
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park,
Calif. 90620
Telephone : 714-522-9011
Type of Equipment : Matrix Processor
Model Name : MTX3
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including
interference that may cause undesired operation.
See user manual instructions if interference to radio reception
is suspected.
* This applies only to products distributed by
YAMAHA CORPORATION OF AMERICA.
(FCC DoC)
(3 wires)
ADVARSEL!
NEDERLAND / THE NETHERLANDS
Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering.
Udskiftning må kun ske med batteri af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandoren.
VARNING
Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens
instruktion.
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda
paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin.
Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.
(lithium caution)
This product contains a battery that contains perchlorate material.
Perchlorate Material—special handling may apply,
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
* This applies only to products distributed
by YAMAHA CORPORATION OF AMERICA.
4 MTX3 Owner’s Manual
(Perchlorate)
• Dit apparaat bevat een lithium batterij voor geheugen back-up.
• This apparatus contains a lithium battery for memory back-up.
• Raadpleeg uw leverancier over de verwijdering van de batterij op het moment dat u het apparaat ann het einde van de
levensduur of gelieve dan contact op te nemen met de vertegenwoordiging van Yamaha in uw land.
• For the removal of the battery at the moment of the disposal
at the end of life please consult your retailer or Yamaha representative office in your country.
• Gooi de batterij niet weg, maar lever hem in als KCA.
• Do not throw away the battery. Instead, hand it in as small
chemical waste.
(lithium disposal)
이 기기는 가정용(B급) 전자파적합기기로서 주로 가정에서
사용하는 것을 목적으로 하며, 모든 지역에서 사용할 수 있습
니다.
(class b korea)
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting,
damages, fire or other hazards. These precautions include, but are not limited to, the following:
Power supply/Power cord
Water warning
• Do not place the power cord near heat sources such as heaters or radiators, and do not excessively
bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone
could walk on, trip over, or roll anything over it.
• Only use the voltage specified as correct for the device. The required voltage is printed on the name
plate of the device.
• Use only the supplied power cord/plug.
If you intend to use the device in an area other than in the one you purchased, the included power cord
may not be compatible. Please check with your Yamaha dealer.
• Check the electric plug periodically and remove any dirt or dust which may have accumulated on it.
• Be sure to connect to an appropriate outlet with a protective grounding connection. Improper
grounding can result in electrical shock.
Do not open
• This device contains no user-serviceable parts. Do not open the device or attempt to disassemble the
internal parts or modify them in any way. If it should appear to be malfunctioning, discontinue use
immediately and have it inspected by qualified Yamaha service personnel.
• Do not expose the device to rain, use it near water or in damp or wet conditions, or place on it any
containers (such as vases, bottles or glasses) containing liquids which might spill into any openings.
If any liquid such as water seeps into the device, turn off the power immediately and unplug the power
cord from the AC outlet. Then have the device inspected by qualified Yamaha service personnel.
• Never insert or remove an electric plug with wet hands.
Fire warning
• Do not put burning items, such as candles, on the unit. A burning item may fall over and cause a fire.
If you notice any abnormality
• When one of the following problems occur, immediately turn off the power switch and disconnect the
electric plug from the outlet. Then have the device inspected by Yamaha service personnel.
- The power cord or plug becomes frayed or damaged.
- It emits unusual smells or smoke.
- Some object has been dropped into the instrument.
- There is a sudden loss of sound during use of the device.
• If this device should be dropped or damaged, immediately turn off the power switch, disconnect the
electric plug from the outlet, and have the device inspected by qualified Yamaha service personnel.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property.
These precautions include, but are not limited to, the following:
Power supply/Power cord
Maintenance
• When removing the electric plug from the device or an outlet, always hold the plug itself and not the
cord. Pulling by the cord can damage it.
• Remove the electric plug from the outlet when the device is not to be used for extended periods of
time, or during electrical storms.
Location
• Do not place the device in an unstable position where it might accidentally fall over.
• Do not block the vents. This device has ventilation holes at the front and sides to prevent the internal
temperature from becoming too high. In particular, do not place the device on its side or upside down.
Inadequate ventilation can result in overheating, possibly causing damage to the device(s), or even fire.
• Do not place the device in a location where it may come into contact with corrosive gases or salt air.
Doing so may result in malfunction.
• Before moving the device, remove all connected cables.
• When setting up the device, make sure that the AC outlet you are using is easily accessible. If some
trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the
outlet. Even when the power switch is turned off, electricity is still flowing to the product at the
minimum level. When you are not using the product for a long time, make sure to unplug the power
cord from the wall AC outlet.
• If the device is mounted in an EIA standard rack, carefully read the section “Precautions for
rackmounting” on page 6. Inadequate ventilation can result in overheating, possibly causing damage
to the device(s), malfunction, or even fire.
• Keep device away from the reach of children.
Connections
• Remove the power plug from the AC outlet when cleaning the device.
Handling caution
• Do not insert your fingers or hands in any gaps or openings on the device (vents).
• Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any gaps or openings on
the device (vents). If this happens, turn off the power immediately and unplug the power cord from the
AC outlet. Then have the device inspected by qualified Yamaha service personnel.
• Do not rest your weight on the device or place heavy objects on it, and avoid use excessive force on
the buttons, switches or connectors.
• Do not use the device/speakers for a long period of time at a high or uncomfortable volume level,
since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears,
consult a physician.
Backup battery
• This device has a built-in backup battery. When you unplug the power cord from the AC outlet, the
internal data is retained. However, if the backup battery fully discharges, this data will be lost. When
the backup battery is running low, the [PRESET] display indicates “12” In this case, immediately save
the data to external device such as a computer, then have qualified Yamaha service personnel replace
the backup battery.
Yamaha cannot be held responsible for damage caused by improper use or modifications to the
device, or data that is lost or destroyed.
Always turn the power off when the device is not in use.
• Before connecting the device to other devices, turn off the power for all devices. Before turning the
power on or off for all devices, set all volume levels to minimum.
Information for Users on Collection and Disposal of Old Equipment
This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should
not be mixed with general household waste.
For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your
national legislation and the Directives 2002/96/EC.
By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on human
health and the environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products, please contact your local municipality, your waste disposal service
or the point of sale where you purchased the items.
[For business users in the European Union]
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
[Information on Disposal in other Countries outside the European Union]
This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and
ask for the correct method of disposal.
(weee_eu_en_01)
European Models
Inrush Current based on EN 55103-1: 2009
2A (on initial switch-on)
2A (after a supply interruption of 5s)
Conforms to Environments: E1, E2, E3 and E4
PA_en_1
1/1
MTX3
Owner’s Manual
5
Getting Started
Thank you for purchasing the Yamaha Matrix Processor MTX3. This manual will help you take full
advantage of the superior functionality offered by the MTX3. After you have read the manual, keep it
in a safe place for reference when needed.
Included items (please check)
• MTX3 Owner’s Manual (this document)
• Power cable
• Euroblock plug (16-pin), (1)
• Euroblock plugs (3-pin, with tab) (16)
• Cable ties (16)
Firmware versions
Use MTX Editor to update the firmware of the MTX3 or check
the firmware version. For details on operation, refer to the MTX
Editor User’s Manual.
Download the latest firmware from the “Downloads” page on
the following website.
http://www.yamahaproaudio.com/
Precautions for rackmounting
This device is guaranteed to operate at an ambient temperature
of 0 to 40 °C. If this device is mounted in an EIA rack together
with other devices, heat from the various devices may cause the
temperature inside the rack to rise, rendering this device unable
to perform to its full potential. To ensure that heat does not
accumulate inside this device, please ensure that the following
conditions are met when rack-mounting it.
• If you plan to mount this device together with devices that
tend to generate heat, such as power amps other than XMV
series products, allow 1U or more of vacant space between
this device and other devices. Also attach ventilation panels
in this space or leave them open to ensure sufficient ventilation.
• Leave the back of the rack open, and allow at least 10 cm of
space between the rack and the wall or ceiling to ensure sufficient ventilation. If the back of the rack cannot be left open,
provide forced air cooling for the rack, for example by
installing a commercially available fan kit. If you install a
fan kit, leaving the back of the rack closed may provide more
effective cooling. For details, refer to the owner’s manual
provided with the rack or fan kit.
6 MTX3 Owner’s Manual
NOTICE
To avoid the possibility of malfunction/ damage to the product,
damage to data, or damage to other property, follow the notices
below.
 Handling and Maintenance
• Do not use the device in the vicinity of a TV, radio, stereo
equipment, mobile phone, or other electric devices. Otherwise, the device, TV, or radio may generate noise.
• Do not expose the device to excessive dust or vibration, or
extreme cold or heat (such as in direct sunlight, near a
heater, or in a car during the day), in order to prevent the
possibility of panel disfiguration, unstable operation, or damage to the internal components.
• Do not place vinyl, plastic or rubber objects on the device,
since this might discolor the panel.
• When cleaning the device, use a dry and soft cloth. Do not
use paint thinners, solvents, cleaning fluids, or chemicalimpregnated wiping cloths.
• Condensation can occur in the device due to rapid, drastic
changes in ambient temperature—when the device is moved
from one location to another, or air conditioning is turned on
or off, for example. Using the device while condensation is
present can cause damage. If there is reason to believe that
condensation might have occurred, leave the device for several hours without turning on the power until the condensation has completely dried out.
• When turning on the AC power in your audio system, always
turn on the power amplifier LAST, to avoid speaker damage.
When turning the power off, the power amplifier should be
turned off FIRST for the same reason.
Information
 About copyrights
• Copying of the commercially available musical data including
but not limited to audio data is strictly prohibited except for
your personal use.
 About this manual
• The illustrations as shown in this manual are for instructional
purposes only, and may appear somewhat different from
those on your device.
• Ethernet is a trademark of Xerox Corporation.
• Windows is a registered trademark of Microsoft® Corporation in the United States and other countries.
• SDHC Logo and SD Logo are trademarks of SD-3C, LLC.
• The company names and product names in this manual are
the trademarks or registered trademarks of their respective
companies.
• MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.
Introducing the MTX3
Features
• A signal processor suitable for small or mid-sized
installed systems
The MTX3 is a signal processor suitable for small or midsized systems such as retail establishments or banquet halls. In
addition to a 26 ch. x 8 ch. matrix mixer, it provides 3-band
parametric EQ, compressor/gate, auto gain control, eight priority duckers, and four feedback suppressors. For the output
stages, it provides numerous high-performance high-quality
processors, such as 4-band parametric EQ, delay, and speaker
processor.
About MTX Editor
MTX Editor is software for the Windows operating system that
allows unified construction and control of systems that use the
MTX series.
MTX Editor and the MTX Editor User’s Manual can be downloaded from the following website.
http://www.yamahaproaudio.com/
For details on installing MTX Editor and connecting the MTX3
to your computer, refer to the “MTX Setup Manual.”
• Newly-developed “YDIF” digital audio transmission format
“YDIF” is a digital audio transmission format that uses Ethernet cable to send and receive up to 16 channels of audio and
word clock. Up to four MTX3 devices can be connected to
expand the number of input/output channels (Cascade mode)
and XMV series power amps can be connected to convey digital audio signals without loss (Distribution mode) via Ethernet
cables up to 30 meters long.
• Versatile input/output and SD memory card slot
In addition to eight high-quality monaural mic/line inputs and
two stereo line inputs, a “YDIF” connection from another
MTX3 device can allow up to 16 channels of input. An SD
memory card slot for playback is also provided; allowing
MP3/WAV audio files saved on the SD memory card to be
played back. In addition to eight channels of analog monaural
output, a maximum of 16 channels of digital audio can be output via a “YDIF” connection.
• Support for external controls
By connecting a “DCP” series dedicated wall-mounted control
panel to the [DCP] connector, you can easily control the volume of multiple zones or switch presets. Daisy-chain connection via Ethernet cable allows up to eight “DCP” series control
panels to be connected. The total cable length from the MTX3
to the farthest control panel can be up to 200 meters, and
power is also supplied, allowing you to place the control panel
in the ideal location for the room.
• Two built-in effect processors
Two effect processors are built-in, and can be easily used in a
party room or banquet hall. You can easily obtain effects such
as reverb or karaoke echo without needing to add dedicated
effect processors.
Using the PDF manual
The MTX Editor User’s Manual is an electronic file in PDF format. You can read this book on a computer. Use Adobe®
Reader® to read this book on screen, search for words very
quickly, print specific pages, or click links to display sections of
special interest. The ability to search for words, or to follow
links directly to relevant sections in the document, are helpful
attributes of this electronic file format. We encourage you to
take advantage of these benefits.
You can download the latest Adobe Reader application from the
website listed below.
http://www.adobe.com/
• Dedicated “MTX Editor” application software for
designing the entire system
“MTX Editor” is application software for editing the parameters of the MTX3. Using operating screens that reflect the
workflow of designing the installation, this software makes it
easy to design a system and make (or adjust) settings. A
speaker library of Yamaha-manufactured speakers is also
built-in, making it easy to choose settings that will maximize
the performance of your speakers.
• iPhone app support
A dedicated iPhone app makes it easy to control the volume
and manage presets in the same way as when using the dedicated wall-mounted control panel. You can use your iPhone/
iPod Touch to easily control the sound system of a retail location or a banquet hall.
MTX3
Owner’s Manual
7
Controls and Connectors
Front Panel
q
we t
yu i
o
!0
!4
88
r
q SD memory card slot
You can insert an SD memory card here. Music or sound
effects can be played back from an SD memory card containing audio files (MP3 files and WAV files). Before you insert
an SD memory card into the slot, or remove an SD memory
card from the slot, remove the slot cover.
For details on SD memory card handling, refer to page 18.
For details on how to play back audio files, refer to the MTX
Editor User’s Manual.
w [INPUT PEAK] indicators 1–8
!1 !2 !3
!0 [NETWORK] indicator
This indicator will light green if a link is established with an
external device via the rear panel NETWORK connector
(page 9). It will blink while data is being sent or received.
!1 [YDIF] indicator
This indicator will light green if the rear panel [YDIF IN]
connector (page 10) is correctly connected to the [YDIF
OUT] connector of another device.
!2 [SCHEDULER] indicator
These indicators will light red when the input level of the
corresponding INPUT channel is -3 dBFS or higher.
This indicator will light orange if an even has been specified
in the scheduler (page 16), and will start blinking one minute
before the event.
e [INPUT SIGNAL] indicators 1–8
These indicators will light green when the input level of the
corresponding INPUT channel is -40 dBFS or higher.
!3 [SD/ACT] indicator
This indicator will light orange if an SD memory card is
inserted in the SD memory card slot (q) and has been
detected correctly. It will blink while the SD memory card is
being accessed.
r [OUTPUT SIGNAL] indicators 1–8
These indicators will light green when the output level of the
corresponding OUTPUT channel is -40 dBFS or higher.
!4
t [PRESET] display
This display usually shows the preset number. It can also
show the UNIT ID, alert number, or a message.
y [s]/[t] buttons
Use these buttons to change the preset number or alert number shown in the above [PRESET] display.
u [ENTER] button
Use this button to confirm the item shown in the above
[PRESET] display.
When an alert number is shown, pressing this button will
return to the preset number display.
i [ALERT] indicator
When an alert occurs, the [PRESET] display will indicate
the alert number and this indicator will blink red.
o [POWER] indicator
This indicator will light when this device is powered-on.
8 MTX3 Owner’s Manual
Power switch
This is the power switch. The power is on if the switch is in
the
position. The power is off if the switch is in the
position.
NOTE
• Do not cycle the power switch in rapid succession. Wait at
least 6 seconds before turning the power switch on after it
has been turned off. Failing to observe this precaution
may cause malfunctions.
• Even when the power switch is turned off, a small amount
of current is flowing through the unit. If you plan not to use
the unit for a long period of time, remove the power cable
from the AC outlet.
Controls and Connectors
Rear Panel
q
!2
w
e
r
u i
t y
!0
!1
o
t [DCP] connector
NOTE
The MTX3 has some connectors that are shaped identically but
have a completely different function (e.g., [DCP] connector, NETWORK connector, [YDIF] connector). Make the appropriate connections as instructed by the explanation for each connector.
Otherwise, you risk damaging your equipment.
q AC IN connector
Use the included power cord to supply power to this connector. First, connect the power cord to this device, and then
insert the power cord plug into the AC outlet.
w Ground screw
The supplied power cord has a three-prong plug that will
ground the device when plugged into an appropriately
grounded three-prong type AC mains outlet. In some cases,
you may be able to reduce hum or interference by also connecting this screw to ground.
Use this connector to daisy-chain separately sold control
panels such as the DCP1V4S to control the MTX3. Use a
CAT5e or better Ethernet straight cable that has all eight pins
connected.
Up to eight control panels can be connected to one MTX3.
The total length of the cables from the MTX3 to the last control panel must not exceed 200 meters.
CAUTION
• Do not connect a control panel to any connector
other than the MTX3’s [DCP] connector. Since the
control panel is not electrically compatible, such connections may cause fire or malfunction.
• Never connect any device to the [DCP] connector
other than the separately sold DCP or other control
panel. Doing so may damage the other device or this
device.
y NETWORK connector
e [GPI] connector
This Euroblock connector allows input and output of control
signals via GPI (General Purpose Interface).
The MTX3 provides seven ports of analog/digital input, one
port of digital input, and four ports of output. The IN-1–7
terminals detect voltage changes from 0V to 5V. The IN-8
terminal alone supports +24V input; voltages in the range of
2.5–24V are detected as High, and voltages below 2.5V are
detected as Low. The OUT 1–4 terminals are open collector
outputs; they will change between open or closed
(GROUND). The +5VDC terminals has an output voltage of
5V. Use the included Euroblock plugs to make connections
(see “Euroblock plug connection” on page 11 for details).
For details on connections and usage, refer to “Connecting
via the [GPI] connector” on page 17.
CAUTION
Do not input a voltage higher than 5V to the IN-1–7
pins. Doing so may damage your equipment.
This is an Ethernet connector that supports AutoMDI/MDIX. It can either be connected directly to a computer, or via a
network switch to communicate with a computer, peripheral
device, or external controller. Use a CAT5e or better Ethernet STP cable (shielded twisted pair cable).
u [UNIT ID] rotary switch
When multiple devices are connected within the same network, this switch specifies the ID by which MTX3 devices
are individually distinguished.
DIP switches 1 and 2 described below specify the upper
digit, and this rotary switch specifies the lower digit,
together allowing you to set the UNIT ID to one of 63 possibilities in the range of 01 to 3F.
NOTE
• Do not use a UNIT ID of “00” (DIP switches 1 and 2 OFF
and the rotary switch at 0).
• You’ll need to restart the device after changing the setting
of the [UNIT ID] rotary switch.
r [RC-232C] connector
Support for this connector is planned for the future.
MTX3
Owner’s Manual
9
Controls and Connectors
i DIP switches
These allow you to make startup settings for the device.
When the device is shipped from the factory, all of these are
set to the OFF (upward) position.
 Switches 7–8 (START UP MODE)
These specify whether the MTX3 will be initialized when
it is powered-on.
Switch position
Option
Functions
RESUME
This is the normal operating
mode. When you power-on
the MTX3, it will start up in
the same state in which it
was when the power was
turned off.
NOTE
You’ll need to power-cycle the device after changing the setting of the DIP switches.
 Switches 1–2 (UNIT ID)
These switches specify the upper digit and the abovementioned [UNIT ID] rotary switch specifies the lower
digit, together allowing you to specify one of 63 different
UNIT ID numbers in a range from 01 to 3F.
Switch position
Option
Functions
UNIT ID is
“0x”
The [UNIT ID] rotary switch
will have a setting range of
01 through 0F.
UNIT ID is
“1x”
The [UNIT ID] rotary switch
will have a setting range of
10 through 1F.
UNIT ID is
“2x”
The [UNIT ID] rotary switch
will have a setting range of
20 through 2F.
UNIT ID is
“3x”
The [UNIT ID] rotary switch
will have a setting range of
30 through 3F.
NOTE
Do not use a UNIT ID of “00” (DIP switches 1 and 2 OFF
and the rotary switch at 0).
 Switches 3–4
These switches are for future expansion.
 Switch 5 (PANEL LOCK)
This switch locks the front panel controls. Use this if you
want to prevent accidental operation from the front panel.
Switch position
Option
Functions
UNLOCK
The front panel controls will
be available for operation.
LOCK
The front panel controls will
be locked, and will be inoperable. The device can be
operated from a computer
or an external controller.
 Switch 6 (IP SETTING)
This switch specifies how the MTX3’s IP address will be
specified.
Switch position
Option
Functions
UNIT ID
The IP address will be
specified according to the
UNIT ID, and will be
192.168.0.(UNIT ID).
PC
The IP address will be
determined by the settings
of MTX Editor. (See “MTX
Editor User’s Manual.”)
NOTE
Set this to the “UNIT ID” position the first time you connect this device to a computer after purchase. After
specifying the IP address from MTX Editor, change this
switch to the “PC” position.
10 MTX3 Owner’s Manual
Initializes the MTX3, returnINIT.
ing it to the factory-set state
(INITIALIZE)
(page 18).
o [YDIF] connectors
These connectors are used to make a ring connection with
the devices that comprise the MTX system, allowing digital
audio signals to be transmitted and received. Use CAT5e or
better Ethernet STP cables (shielded twisted pair cables) that
have all eight pins connected in a straight connection. The
maximum cable length between devices is 30 meters, and
you can connect up to eight devices that are equipped with
the [YDIF] connectors. For details, refer to the MTX Editor
User’s Manual.
!0 [ST IN] connectors
These are unbalanced RCA phono jacks for inputting analog
audio signals from a CD player or other device.
!1 [INPUT] [OUTPUT] connectors
These are balanced input/output connectors for analog audio
input and output. Connect line level devices or microphones
to the [INPUT] connectors, and line level devices to the
[OUTPUT] connectors. The [INPUT] connectors provide
head amps, and can also provide +48V phantom power.
MTX Editor is used to specify the gain of the internal head
amps and to turn the phantom power on/off.
Use the included Euroblock plugs to make connections (see
“Euroblock plug connection” on page 11 for details).
NOTE
Adjusting the internal head amp gain between +17 dB and
+18 dB will internally turn PAD on/off. Noise may occur if
there is an impedance difference between the Hot and Cold
of a device connected to the [INPUT] connectors while
phantom power is being used.
!2 Cooling vent
The MTX3 contains a cooling fan. The cooling air is
exhausted here, so please be careful not to block this vent.
Cooling vent
Controls and Connectors
 Euroblock plug connection
1. Loosen the terminal screws.
Use the included Euroblock plugs when making connections
to the [INPUT]/[OUTPUT] connectors and [GPI] connector.
Loosen
Slotted screwdriver
Cable preparation
Terminal screw
approx. 7 mm
(approx. 5 mm for
the GPI connector)
Euroblock plug
approx. 20 mm
• Use stranded wire for Euroblock connections, and
strip the wire as shown in the illustration. With a
Euroblock connection, the stranded wire may be
prone to breakage because of metal fatigue due to
the weight of the cable or due to vibration. Cables
connected to the [INPUT]/[OUTPUT] connectors
should be fastened to the tab of the Euroblock plug
(3-pin) using the included cable ties (see illustration
at right). When rack-mounting the device, use a lacing bar when possible to bundle and secure the
cable.
Tab
* The explanation uses tabbed Euroblock plugs.
NOTE
Use a slotted screwdriver with a blade width of 2 mm or
less for the [GPI] connector’s Euroblock plug (16-pin),
and a blade width of 3 mm or less for the [INPUT]/[OUTPUT] connector’s Euroblock plug (3-pin).
3 mm or less
NOTE
Do not tin (plate with solder) the stranded wire.
• If cables will be frequently connected and disconnected, as in the case of a portable system, we recommend that you use ferrules with insulation
sleeves. Use a ferrule whose conductor portion has
an external diameter of 1.6 mm or less (1.3 mm or
less for the [GPI] connector) and a length of approximately 7 mm (approximately 5 mm for the [GPI]
connector) such as the AI 0,5 - 6 WH made by the
Phoenix Contact corporation.
approx. 7 mm
(approx. 5 mm for
the GPI connector)
1.6 mm or less
(1.3 mm for the GPI connector)
2. Insert cables.
+ –
G
3. Securely tighten the terminal screws.
Pull the cables (not too strongly) to confirm that they are
securely connected.
4. For the Euroblock plugs (3-pin) of the
[INPUT]/[OUTPUT] connectors, use the
included cable ties to fasten the cable to the
tab.
NOTE
Trim off the extra portion of the cable tie as necessary.
MTX3
Owner’s Manual
11
Controls and Connectors
5. Plug the Euroblock plug into the [GPI] connector or [INPUT]/[OUTPUT] connector of
the MTX3.
NOTE
When connecting unbalanced cables to the [INPUT]
connector, use a jumper wire to connect the “-” and “G”
of the Euroblock.
+ –
12 MTX3 Owner’s Manual
G
Quick Guide
This section explains basic settings and connection procedures for constructing an MTX system using
the MTX3. Some of the steps may not be necessary for your system; if so, proceed to the next step.
Preparations
Use MTX Editor to make the required settings before you actually install and connect the equipment.
1. Prepare a computer in which to install MTX
Editor.
7. The audio signal flow in the MTX3 and the
principal parameters to be set are as follows.
Make the settings in the order shown.
For details on each item, refer to “MTX Editor User’s Manual.”
Input port settings (e.g., HA gain, +48V on/off)
The computer must meet the following requirements.
• OS:
Windows7 Home Premium or higher
• Recommended specifications:
CPU
: Core i3/5 or better
Memory : 4GB or more
HDD
: 50 MB or more free space
Input patching
Input channel settings (e.g., gain, HPF, EQ)
Matrix
2. Install MTX Editor in your computer.
For details on installation, refer to “MTX Setup Manual.”
3. Specify the IP address and subnet mask of
your computer.
Enter “192.168.0.253” as the IP address and
“255.255.255.0” as the subnet mask.
4. If you want to play back music or other audio
files from the MTX3 itself, prepare an SD memory card.
Copy the audio files to your SD memory card. For details on
SD memory card handling, refer to “Using the MTX3 to play
audio files saved on an SD memory card” (page 18).
5. Start up MTX Editor.
For details on installing and using MTX Editor, refer to
“MTX Setup Manual” and “MTX Editor User’s Manual.”
6. Set up the entire MTX system as directed by
the wizard.
Make settings such as the number of connected MTX/XMV/
DCP devices, and the UNIT ID and YDIF mode (Cascade
mode or Distribution mode) for each device. For details on
YDIF, refer to “Features” (page 7), and “o [YDIF] connectors” in “Controls and Connectors” (page 10).
Print out the schematic diagram shown at the end of the wizard, and use it when you make the actual connections and
settings.
Matrix/zone settings
Router
Output channel settings (e.g., output level, delay/
room EQ, speaker processor)
Output patching
Output port settings (e.g., polarity, output gain)
As necessary, make input patching and output patching settings to specify the audio signal flow of the devices connected to the MTX3’s [INPUT] /[ST IN]/[OUTPUT]/
[YDIF] connectors.
Make settings for the necessary components while offline.
• HA section:
HA gain, +48V (phantom power)
• Input channel section:
HPF, 3BAND EQ, GATE, COMP, FBS, AGC, Level
• Matrix/Zone section:
Two-level priority ducker, ANC
• Output channel section:
Room EQ (Delay, 4Band EQ), SPEAKER PROCESSOR (X-over, Delay, 6Band EQ, Level, Limiter)
MTX3
Owner’s Manual
13
Quick Guide
8. Make DCP settings.
Assign the parameters of the MTX3 to the switches and
knobs of the connected DCP units. Here you can also specify
the brightness of the DCP’s LEDs.
9. Specify and store a preset.
You can use presets to change the volume of zones and the
audio source to play (e.g., SD memory card or CD player) in
a single action. To prevent problems such as a sudden
increase in volume when the MTX3 is operated, we recommend that you store the preset with the output level lowered
to “-infinity ().” For details on presets and how to recall
them, refer to “Recalling (switching) presets” on page 16,
and “MTX Editor User’s Manual.”
10. Save your settings and close MTX Editor.
A project file with the extension “.mtx” will be created.
On-site work (Installation and wiring)
Install and connect the system while referring to the schematic
diagram you printed out.
1. Install the MTX3, and make the analog audio
connections.
2. Make digital connections between the MTX3
and any XMV.
Make a ring connection between the MTX3 and the other
devices equipped with a [YDIF] connector, such as an XMV
series amplifier.
3. Connect the MTX3 to an analog input amp
(other than XMV).
4. Set the UNIT ID of the MTX3 and the XMV.
Set the UNIT ID for every MTX3 and XMV device you connected in the above steps. The UNIT ID is specified by the
combination of the [UNIT ID] rotary switch and DIP
switches located on each device’s rear panel. Set each device
to a different UNIT ID so that no conflict occurs.
5. Make connections between the MTX3 and the
DCP units.
Daisy-chain the DCP units. Set the panel ID and termination
settings of the DCP units. For details, refer to the DCP
owner’s manual.
14 MTX3 Owner’s Manual
Quick Guide
On-site work (Settings in MTX Editor)
Use MTX Editor to make adjustments for the entire system.
1. Connect the MTX3 to the computer.
Connect the computer to the MTX3 directly or via a network
switch.
2. Start up MTX Editor and load the project file
that you previously created.
3. Power-on the MTX3.
4. Power-on the amps.
5. Go the MTX3 and MTX Editor online (in a synchronized state).
“Online” refers to the state in which the MTX3 itself is connected with MTX Editor and is synchronized. For details on
how to put the device online, refer to “MTX Editor User’s
Manual.”
6. Check the signal processing.
10. Place the XMV and MTX Editor online.
When they go online, the amp will be detected and you will
be able use MTX Editor to control the XMV. MTX Editor
will detect the devices that are connected on the network,
and will put the detected devices online.
11. Adjust the output level of the MTX3 and the
output level of the amps so that the audio is
output at an appropriate level.
One by one, turn on each output channel and adjust its output level.
12. Store the preset.
As necessary, recall a preset that includes output, specify
the output level, and save the preset. Recall, edit, and save
other presets in the same way.
13. Save your settings and close MTX Editor.
A project file with the extension “.mtx” will be created.
NOTE
The settings you make while online are saved in the MTX3
itself, but we recommend that you use MTX Editor to save
them as a project file for future maintenance and readjustments.
Input an audio signal into the MTX3, and check the meter in
MTX Editor to verify that the volume and routing are set
correctly.
7. Check and edit the presets.
Recall the presets, and verify that each has the correct settings.
For details on presets and how to recall them, refer to
“Recalling (switching) presets” on page 16.
8. Using the meter in MTX Editor, verify that the
audio signals are being output from the MTX3
at an appropriate level.
9. Temporarily turn off the audio output from the
MTX3.
To prevent loud sound from the amp from damaging your
speakers, we recommend that you turn off the audio output
from the MTX3.
MTX3
Owner’s Manual
15
Various Procedures
Recalling (switching) presets
Using the scheduler
With the MTX system, input/output port patching, matrix mixer
settings, and the parameters of XMV amps within the same
MTX system are stored together as a “preset” in the MTX3 and
in MTX Editor for recall when desired.
Each MTX system can store 50 presets. MTX Editor is used to
edit presets.
The scheduler can switch presets or play music and sound
effects from the SD memory card at the date and time you specify. Each such setting is called an “event.”
Event settings are made in the “Scheduler” dialog box of MTX
Editor. For details on operation, refer to “MTX Editor User’s
Manual.”
Each preset contains settings such as the following.
< Example 1 >
Switching background music and playback area
according to the time of day
• Input/output port settings and patching
• Input/output channel gain and EQ settings
• Matrix mixer settings
• Zone settings
• Routing settings
• Effect settings
• VCA and mute group settings
• Parameter settings for XMV devices within the same MTX
system
• Preset name
 Switching presets from the MTX3
1. While watching the [PRESET] display, use
the [s]/[t] buttons to select the preset
number that you want to recall.
The [PRESET] display will blink during this time.
2. Press the [ENTER] button to confirm your
selection.
The [PRESET] display will stop blinking; the preset has
been recalled.
In commercial facilities that switch background music and playback areas at different times of the day, you can switch the type
of music and the playback area according to the time of day.
9:00
12:00
14:00
18:00
22:00
Indoors
Atmospheric
music
Energetic
music
Outdoors
Refreshing
music
Calm music
No music
No music
< Example 2 >
Switching the playback time according to the day
of the week
In commercial facilities that switch the time period of music
depending on the day of the week, you can specify the music
pattern and playback times according to the day of the week and
the hours of operation.
NOTE
• If you leave the device for 30 seconds with the [PRESET] display blinking, it will revert to the previous preset number.
• If a control panel such as a DCP series unit is connected, you’ll be able to easily switch presets.
• Monday–Friday
10:00
20:00
Music pattern 1
• Saturday
10:00
22:00
Music pattern 2
Setting the clock
• Sunday
When all devices connected to the MTX system go online, the
internal clock of each device is automatically updated with the
date and time settings transmitted from the computer’s clock.
You can also update the date and time settings on all devices
connected to the same network by transmitting the computer’s
date and time settings from the “Clock” dialog box in MTX
Editor.
For more information on operation, refer to “MTX Editor
User’s Manual.”
16 MTX3 Owner’s Manual
12:00
20:00
Music pattern 3
You can also play seasonal music, or specify exceptions such as
stopping playback on days when the facility is not operating.
Various Procedures
Connecting via the [GPI] connector
GPI (General Purpose Interface) devices can be connected to
the rear-panel [GPI] connectors. GPI allows a variety of control
signals to be exchanged with external controllers or other
devices.
• Connection examples using the [GPI IN] connector
Example: Controlling the MTX3 from a switch box
MTX3
+5VDC
+V
CPU
IN
A/D
100k
The MTX3 provides 8 input ports and 4 output ports.
• The +5VDC terminals have an output voltage of 5V. The
maximum current draw is 100 mA total for the two terminals. If you are using a switch/variable resistor and an LED/
relay simultaneously, connect one terminal to the switch/
variable resistor and the other terminal to the LED/relay.
• The IN-1–7 terminals detect voltage changes from 0V to
5V. The IN-8 terminal alone supports +24V input; voltages
in the range of 2.5–24V are detected as High, and voltages
below 2.5V are detected as Low.
• The OUT 1–4 terminals are open collector outputs; they
will change between open or closed (GROUND). The maximum voltage that can be applied is +12V. The maximum
current draw is 75 mA per port.
The GPI controller parameters are assigned via the MTX Editor
application.
Euroblock plugs (16-pin) are used for connections to the [GPI]
connector. For details, refer to “Euroblock plug connection” on
page 11.
Example: Controlling the MTX3 with a 10k ohm
linear taper potentiometer.
MTX3
+5VDC
+V
CPU
Variable
resistor
IN
A/D
GND
100k
• Connection examples using the [GPI OUT]
connector
Example: Lighting LED indicators on external
devices from the MTX3
MTX3
NOTE
+5VDC
By making input/output channel settings in MTX Editor, you
can recall presets or edit parameters on an external GPI device
or send signals to it. For details, refer to the “MTX Editor User’s
Manual.”
+V
10
OUT
Max. 75mA
CPU
CAUTION
Do not exceed 75 mA of current from the OUT connector.
Example: Lighting an LED by switching an external device’s relay from the MTX3
MTX3
+
+5VDC
+V
10
OUT
CPU
–
Max. 75mA
NOTE
For the method of adjusting the detection range of the input
voltage at the [GPI] connector (calibration), refer to the “MTX
Editor User’s Manual.”
MTX3
Owner’s Manual
17
Various Procedures
Using the MTX3 to play audio files
saved on an SD memory card
The MTX3 can use commercially available SD memory cards
to play back audio files such as music and sound effects without
needing to connect a CD player or other audio device. The
MTX3 can play back audio files in either MP3 or WAV formats.
Here we explain how to handle SD memory cards. In order to
play back audio files saved on an SD memory card, you must
make settings in MTX Editor. For details, refer to “MTX Editor
User’s Manual.”
NOTE
Use an SD format or SDHC format memory card (SDXC format
is not supported). However, depending on the manufacturer or
type of memory card, some memory cards might not work correctly with the MTX3.
 Inserting an SD memory card
1. Use a 2.5 mm hex key to open the cover of
the SD memory card slot.
Initializing the MTX3
Here’s how to initialize the MTX3’s internal memory, restoring
it to the factory settings.
1. Power-off the MTX3.
2. Set the rear panel DIP switches 7 and 8 to the
“INIT. (INITIALIZE)” position.
3. Power-on the MTX3.
Initialization will start.
The status of execution is shown by the front panel [ALERT]
indicator and the various indicators from [NETWORK]
through [SD/ACT].
• During initialization:
All indicators from [NETWORK] through [SD/ACT]
will blink.
2. With the terminals of the SD memory card
facing downward, insert the card straight
into the slot until it clicks into place.
• Initialization completed:
Only the [NETWORK] indicator and the [YDIF] indicator will blink.
When the SD memory card has been correctly recognized, the [SD/ACT] indicator (page 8) will light. The
[SD/ACT] indicator will blink while the card is being
accessed.
NOTE
To prevent theft of the SD memory card, we recommend
that you leave the cover installed during use.
• Initialization failed:
The [ALERT] indicator will blink.
 Removing the SD memory card
1. Gently press the SD memory card inward.
The card will pop out slightly; gently pull it completely
out.
CAUTION
Do not turn off the power to the MTX3 during initialization. Otherwise, a malfunction may occur
NOTE
If initialization failed, contact Yamaha representatives /
authorized distributors to have the device inspected. A list of
Yamaha representatives / authorized distributors appears
near the end of this manual.
18 MTX3 Owner’s Manual
Various Procedures
4. When initialization is completed, power-off the
MTX3 once again.
5. Set the rear panel DIP switches 7 and 8 to the
“RESUME” position.
6. Power-on the MTX3 again.
The MTX3 will start up in its factory-set state.
MTX3
Owner’s Manual
19
Appendix
 Troubleshooting
Symptom
Possible cause, and action
Connect the power cord properly.
The device does not turn on, or
the panel LEDs do not light up.
Make sure that the power switch is turned on.
If the power still does not turn on, contact your Yamaha dealer.
Is the NETWORK connector on the MTX3 properly connected to your computer?
Can’t exchange data between the
MTX3 and MTX Editor
(MTX3 is not shown in MTX Editor)
No audio input is present.
([INPUT SIGNAL] indicator does
not light)
Have you specified the correct UNIT ID using the [UNIT ID] rotary switch and DIP switches 1 and 2
on the rear panel? Could the UNIT ID be conflicting with another device?
Set the rear panel DIP switch 6 (IP SETTING) to “UNIT ID” so that the IP address will be automatically assigned according to the UNIT ID.
Connect the cable properly.
Make sure that a signal from an external device is being input.
Set the gain of the internal head amplifier or external head amplifier to an appropriate level.
Could the output level be lowered?
No audio is output.
([OUTPUT SIGNAL] indicator
does not light)
In MTX Editor, could the channel’s ON button be turned off?
Is the signal routing specified correctly?
Have the other settings in MTX Editor been made correctly?
The panel controls don’t work.
Could rear panel DIP switch 5 (PANEL LOCK) be set to “LOCK”? Change this to “UNLOCK” to
defeat the panel lock function. If you are still unable to operate the device, contact your Yamaha
dealer.
Are you using an appropriate cable, and is the MTX3 correctly connected to the DCP?
Did you power-cycle the MTX3 after connecting the DCP? The DCP will be detected when the
power is turned on.
Can’t operate the DCP
Did you assign the DCP’s ID and parameters correctly in MTX Editor?
Is termination turned on for the last-connected DCP?
Could nine or more DCP units be connected? A maximum of eight DCP units can be connected to
one MTX3.
Could the total cable length from the MTX3 to the last control panel be exceeding 200 meters?
The DCP’s LEDs are dim
Did you set the DCP’s LED brightness appropriately in MTX Editor?
[YDIF] indicator does not light
Did you use an appropriate cable to make proper YDIF connections between the MTX3 and other
devices in the MTX system? Also, is the power to the YDIF-connected devices turned on?
Is the SD memory card recognized correctly? Check the front panel [SD/ACT] indicator.
Can’t play audio files from the SD
memory card
In MTX Editor, have you made the correct settings for SD memory card playback and for the scheduler?
Are playable audio files saved in the specified folder?
Are you using an SD memory card type and format that is supported? Refer to the “Specifications”
page, and use a supported card.
SD memory card is not detected
Preset does not switch at the time
specified by the scheduler
The [ALERT] indicator is blinking
Can’t switch presets from a device
connected to the [GPI] connector
Volume becomes unstable when
it is operated from a device connected to the [GPI] connector
20 MTX3 Owner’s Manual
Is the SD memory card inserted correctly? Turn off the power of the MTX3, re-insert the card, and
then turn the power on again. If the [SD/ACT] indicator does not light and the card is not detected, it
may be that the card is damaged.
The MTX3’s clock is set by sending clock data from the computer via MTX Editor to the MTX3.
Make sure that the computer’s clock is set correctly.
Have you made the correct scheduler settings in MTX Editor? If the [SCHEDULER] indicator is not
lit or blinking, it may be that settings were not made correctly in MTX Editor.
An error has occurred. The alert number is shown in the front panel [PRESET] display; refer to
“Alert list” on page 21 to determine the content of the error and take the appropriate action.
Is the GPI device connected correctly?
Have the correct GPI-related settings been made in MTX Editor?
Route the wiring to avoid picking up noise; for example, replace the cable with a shielded or shorter
cable.
Appendix
 Alert list
This is a list of the alerts that may be indicated in the front panel [PRESET] display.
Alert
number
Meaning
Response
01–09
The device has not started up correctly.
Turn the power off, then turn on after waiting at least 6 seconds. If this does not
solve the problem, please initialize the memory (use rear panel DIP switches 7
and 8.) Should this also fails, contact your Yamaha dealer.
10
The internal backup battery has been
completely exhausted or is not installed.
When you turn off the power, the current settings will be lost, and will return to the
default values. Please stop use immediately, and contact your Yamaha dealer.
11
The internal backup battery has run
extremely low, and it is possible that the
internal memory has been cleared.
When you turn off the power, the current settings will be lost, and will return to the
default values. Please stop use immediately, and contact your Yamaha dealer.
12
The internal backup battery has only a
small amount of power remaining.
This does not affect the operation of the device. However, if you continue using the
device, the settings may be lost and reset to the default values. Contact your
Yamaha dealer as soon as possible.
13
A problem has occurred with the internal
clock, and it has been initialized (January
1, 2000, 0:00)
If this occurs each time you turn on the power, it is possible that the internal
backup battery has run down or that the device has malfunctioned. Contact your
Yamaha dealer.
If this occurs only once, an abnormality was detected with the clock setting and it
was initialized; use MTX Editor to set the time.
14
The current preset saved in internal memRecall the preset. If this does not solve the problem, contact your Yamaha dealer.
ory has been lost.
15
The settings saved in internal memory
have been lost.
Either the internal backup battery has run low, or the device has malfunctioned.
Contact your Yamaha dealer.
21
The word clock master has become
unlocked.
Make sure that the word clock signal is being input correctly.
22
The digital signal being input to the [YDIF
IN] connector is not synchronized to the
word clock of this device.
23
The digital signal being input to the [YDIF
IN] connector is not locked to the word
clock of this device.
30
There is a problem with the connection of
the [YDIF IN] connector.
Make sure that YDIF cables are properly connected.
Use cables that meet the required specifications.
40
Duplicate IP addresses.
Change the IP addresses so that there are no duplicates.
41
IP address was not set within 60 seconds
of startup.
Please check rear panel DIP switch 6 (IP Setting). If DIP switch 6 is set to “PC,”
use MTX Editor or the DHCP server to specify the device IP address.
42
A device within the MTX system was not
found on the network.
Power-on all devices in the system, and make sure that they are correctly connected to the network.
43
Too many devices connected to the NETWORK connector.
Disconnect unneeded devices from the network.
50
The UNIT ID is set to “00.”
Set the UNIT ID to something other than “00.”
51
Devices with identical UNIT IDs were
found connected within the same network.
Change the UNIT ID so that there are no duplicates.
52
A communication error occurred with the
[DCP] connection.
• If an error was shown in the DCP panel, refer to the DCP owner’s manual and
take the appropriate action
• Ensure that the panel ID of the DCP units do not conflict
• Verify that the cables are correctly connected and are within the specified length
53
The DCP connected to the [DCP] connec• Are all required DCP units connected?
tor has been configured differently from
• Could a DCP unit of a different model be connected?
the project settings.
56
SD memory card was not recognized.
Use an SD memory card that complies with the specifications. (See page 22.)
58
Unable to play the specified file or folder
in the SD player.
Verify that the specified audio file or folder exists in the SD memory card. There
must be at least one playable audio file in the specified folder.
60
A preset recall attempt has failed.
Initialize the memory of the device (use rear panel DIP switches 7 and 8.) If this
does not solve the problem, please contact your Yamaha dealer.
61
The recall could not be executed because
Specify a preset that exists. No sound will be output unless an appropriate preset
the preset to be recalled when the MTX
is recalled.
starts up was not found.
64
The preset could not be recalled.
70
Synchronization has not been comPerform synchronization again using MTX Editor. If this does not solve the probpleted. It may be that synchronization was lem, initialize the memory of the device and synchronize again. If this also fails,
halted before completion.
contact your Yamaha dealer.
71
The UNIT ID settings when synchronization was performed do not match the current UNIT ID settings.
• The Preset selected for recall cannot be recalled as no data has been stored to it.
• Another device may have been added after presets were stored. Please synchronize and check all Presets using MTX Editor, edit as necessary and store again.
Do not change any UNIT ID’s after performing synchronization. If you’ve changed
any UNIT ID’s, perform synchronization again.
MTX3
Owner’s Manual
21
Appendix
 Specifications
Product specifications
Dimensions (W x H x D)
480(W) x 44(H) x 351(D)mm, 1U
Weight
4.8 kg
Power supply voltage
Japan: 100V 50/60Hz
US/Canada: 110V–240V 50/60Hz
Others: 100V–240V 50/60Hz
Power consumption
50W (43kcal/h) max.
Heat dissipation (per hour)
43kcal max.
Operating temperature range
0 °C–40 °C
Storage temperature range
-20 °C–60 °C
NC value
27
Number of memories
Preset memories: 50
Maximum number of simultaneously usable devices
Four MTX devices (However in a system in which one to four MTX devices are connected, a total of up
to 20 devices including devices such as the XMV can be connected.)
Power cord length
2.5m
Included items
Power cord, Euroblock plugs (3-pin, tabbed) x 16, Euroblock plug (16-pin) x 1, cable ties x 16,
owner’s manual
Separately sold options
DCP1V4S-US/EU digital control panels
Electrical specifications
Sampling frequency
48 kHz
Signal delay
Less than 2.5ms (AD-DA @48kHz)
Frequency response
20Hz to 20kHz, -1.5dB min, 0dB typ., +0.5dB max.
Total harmonic distortion
Less than 0.05% (+4dBu, Gain:-6dB); less than 0.1% (+4dBu, Gain:+66dB)
Dynamic range
107dB (Gain:-6dB)
Equivalent input noise (EIN)
-126dBu (Gain: +66dB)
Crosstalk / Channel separation -100dB (@1kHz)
Maximum cable length
[YDIF] connector: 30 meters (Cable length between devices)
[DCP] connector: 200 meters (total cable length from the MTX3 to the last DCP)
Indicators
INPUT PEAK: RED -3dBFS
INPUT SIGNAL: GREEN -40dBFS
OUTPUT SIGNAL: GREEN -40dBFS
Phantom power
48V (per channel; individually settable)
Connector specifications
Format
[GPI] connector: IN (1-7ch): 0–5V
IN(8ch): 2.5–24V : High, 2.5V or less: Low, Allowable input +24V
OUT: Open collector
+V: DC5V
NETWORK connector: 100Base-TX
[RC-232C] connector: RS-232C (BAUD RATE: 38.4 kbps/115.2kbps)
Cable specifications
[DCP] connector: CAT5e or better Ethernet cable (Straight connected. All 8 pins must be connected.)
[YDIF] connector: CAT5e or better Ethernet STP cable (Straight connected. All 8 pins must be connected.)
NETWORK connector: CAT5e or better Ethernet STP cable
SD Memory card specifications
Supported formats
File formats: FAT32, FAT16, FAT12
Files created on a computer running Windows XP or later, or Mac OS X or later.
Supported capacities
Maximum media capacity: SDHC: Max. 32 GB
SD: Max. 2GB
Maximum file size
(maximum size per file)
FAT12: Max. 32MB
FAT16: Max. 2GB
FAT32: Max. 2GB
Audio file format: WAV
16bit 2ch PCM
Sampling frequencies: 8kHz, 11.025kHz, 12kHz, 16kHz, 22.05kHz, 24kHz, 32kHz, 44.1kHz, 48kHz
Audio file format: MP3
MPEG-1/2/2.5 Audio Layer-3
sampling frequencies: MPEG-1: 32kHz, 44.1kHz, 48kHz
MPEG-2: 16kHz, 22.05kHz, 24kHz
MPEG-2.5: 8kHz, 11.025kHz
Bit rate: MPEG-1: 32kbps–320kbps, VBR (Variable Bit Rate) * However, free format is excepted.
MPEG-2, 2.5: 8 kbps–160 kbps, VBR (Variable Bit Rate) *However, free format is excepted.
* Specifications and appearance are subject to change without notice for improvement.
22 MTX3 Owner’s Manual
Appendix
 Input/Output Characteristics
ANALOG INPUT CHARACTERISTICS
Input
Terminals
INPUT 1–8
GAIN
+66dB
-6dB
ST IN 1, 2
—
Actual Load
Impedance
For Use With
Nominal
10kΩ
10kΩ
Input Level
Connector
Nominal
Max. before clip
50–600Ω Mics
& 600Ω Lines
-62dBu (0.616mV)
-42dBu (6.16mV)
+10dBu (2.45V)
+30dBu (24.5V)
Euroblock (Balanced)
(5.08mm pitch)
600Ω Lines
-10dBV (316mV)
+10dBV (3.16V)
RCA Pin Jack
• In these specifications, 0dBu = 0.775 Vrms., 0dBV = 1.00 Vrms.
• All input AD converters are 24bit linear, 128times oversampling.
• +48V DC (phantom power) is supplied to INPUT EUROBLOCK connectors via each individual software controlled switch.
ANALOG OUTPUT CHARACTERISTICS
Output Level
Output Terminals
Actual Load
Impedance
For Use With
Nominal
Nominal
Max. before clip
OUTPUT 1–8
75Ω
10kΩ Lines
+4dBu (1.23 V)
+24dBu (12.3V)
Connector
Euroblock (Balanced)
(5.08mm pitch)
• In these specifications, 0dBu = 0.775 Vrms.
• All output DA converters are 24bit, 128times oversampling.
 Dimensions
356
6
362
351
4
430
44
480
Unit: mm
MTX3
Owner’s Manual
23
YDIF
IN
SD IN
L-R
ST IN
1L-2R
INPUT
1-8
24 MTX3 Owner’s Manual
+48V
AD
AD
AD
16
EFFECT 1
EFFECT 2
From FX2
SUM
SUM
INPUT
METER
INPUT
METER
INPUT
METER
8
*DISTRIBUTION MODE only
To PRIORITY/AMBIENT SOURCE
To ROUTER IN
To YDIF OUTPUT PATCH
YDIF IN
INPUT
PATCH
SD IN
L-R
ST IN
1L-2R
INPUT
1-8
YDIF IN
1-16
INPUT
PATCH
*CASCADE MODE only
From FX1
EFFECT
GAIN
+
-
+48V
INPUT
METER
8
YDIF IN
CASCADE MODE
or DISTRIBUTION MODE
YDIF MODE
INPUT PORT
HPF
3BAND
EQ
GATE
GR
COMP
GR
EQ OUT
METER
3BAND
EQ
GR
COMP*
EFFECT RETURN 1L-2R (FX RTN 1L-2R)
DIRECT INPUT CHANNEL(CH9-16)
DIGITAL
GAIN
STEREO INPUT CHANNEL(STIN1L-3R)
DIGITAL
GAIN
EQ OUT
METER
INPUT CHANNEL(CH1-8)
AGC*
* CH 1L-2R only
AGC*
* CH 1-4 only
FBS*
8
POST ON
METER
ANC SEND
LEVEL ON
EFFECT SEND
LEVEL ON
To MATRIX(STEREO)
LEVEL ON
PAN
MATRIX CROSS POINT
To MATRIX(MONO)
LEVEL ON
CASCADE ON
CASCADE ON
CASCADE ON
ANC SEND
LEVEL ON
EFFECT SEND
LEVEL ON
To MATRIX(STEREO)
LEVEL ON
PAN
MATRIX CROSS POINT
To MATRIX(MONO)
LEVEL ON
ANC SEND
LEVEL ON
EFFECT SEND
LEVEL ON
To MATRIX(STEREO)
LEVEL ON
PAN
MATRIX CROSS POINT
To MATRIX(MONO)
LEVEL ON
ON
POST ON
METER
To MATRIX(STEREO)
LEVEL ON
PAN
MATRIX CROSS POINT
To MATRIX(MONO)
LEVEL ON
To PRIORITY/AMBIENT SOURCE
D ON
C
A
POST ON
METER
To YDIF OUTPUT PATCH
To PRIORITY/AMBIENT SOURCE
D ON
C
A
POST ON
METER
To YDIF OUTPUT PATCH
To PRIORITY/AMBIENT SOURCE
D ON
C
A
To other MTXs
LEVEL
LEVEL
LEVEL
LEVEL
YDIF IN 8
YDIF IN 2
YDIF IN 1
CASCADE I/O
INPUT CHANNEL
To MATRIX2,4...8
To MATRIX1,3...7
To MATRIX1,3...7
To MATRIX2,4...8
To ANC1
To ANC2
To FX1
To FX2
To MATRIX2,4...8
To MATRIX1,3...7
To MATRIX1,3...7
To MATRIX2,4...8
To ANC1
To ANC2
To FX1
To FX2
To MATRIX2,4...8
To MATRIX1,3...7
To MATRIX1,3...7
To MATRIX2,4...8
To ANC1
To ANC2
To FX1
To FX2
To MATRIX2,4...8
To MATRIX1,3...7
To MATRIX1,3...7
To MATRIX2,4...8
1 2
7 8
MATRIX
FX ANC
1 2 1 2
MATRIX
YDIF OUT 1
To PRIORITY/AMBIENT SOURCE
To PRIORITY/AMBIENT SOURCE
To EFFECT 1
To EFFECT 2
EFFECT SEND
PRIORITY
SOURCE
*1 DISTRIBUTION MODE only
From DIRECT INPUT POST ON 9-16
From ANC BUS 1-2
*1 From YDIF IN 1-16
From STEREO INPUT CHANNEL POST ON 1L-3R
GR
PRIORITY
SOURCE
PRIORITY
DUCKER
GR
PRIORITY
DUCKER
MIX
AMBIENT
SOURCE
ON
From YDIF IN 1-16
To other MTXs
To YDIF
OUTPUT
PATCH
ZONE OUT
MASTER METER
LEVEL
D ON
C
A
LEVEL
8
*DISTRIBUTION MODE only 16
AMBIENT
METER
ANC
ANC
Burst Noise
Pink Noise
Sine Wave
OSCILLATOR
FREQ.
1st PRIORITY
MIX
8
2nd PRIORITY
*CASCADE MODE only
YDIF OUT 8
YDIF OUT 2
From INPUT CHANNEL POST ON 1-8
ZONE 1-8
CASCADE ON
CASCADE ON
CASCADE ON
ZONE
ROUTER
8
ROUTER
DELAY
4BAND
EQ
ROOM EQ/DELAY
X-OVER
OUTPUT
LEVEL
ON
DELAY
4BAND
EQ
ROOM EQ/DELAY
X-OVER
DELAY
DELAY
6BAND
EQ
6BAND
EQ
SPEAKER PROCESSOR
DELAY
LEVEL
MUTE
LEVEL
MUTE
MUTE
LEVEL
LIMITER
GR
LIMITER
GR
LIMITER
GR
OUTPUT
METER
OUTPUT
METER
OUTPUT
METER
From THRU 1-16
From ZONE OUT 1-8
From STEREO INPUT CHANNEL POST ON 1L-3R
6BAND
EQ
SPEAKER PROCESSOR
OUTPUT CHANNEL 1-8 (2way)
ON
OUTPUT CHANNEL 1-8 (1way)
OUTPUT
LEVEL
*CASCADE MODE only
OUTPUT
PATCH
8
8
16
8
6
8
OUTPUT
PATCH
YDIF
OUTPUT
PATCH
*DISTRIBUTION MODE only
From INPUT CHANNEL POST ON 1-8
YDIF OUT
YDIF OUT
OUTPUT CHANNEL
8
DA
OUTPUT
POLARITY OUTPUT METER
GAIN
16
8
CASCADE MODE
or DISTRIBUTION MODE
YDIF MODE
YDIF
OUT
OUTPUT
1-8
OUTPUT PORT
Appendix
 Block Diagram
Appendix
 Index
Symbols
+48V ...................................................................... 10
[s/t] buttons ........................................................... 8
[ALERT] indicator ..................................................... 8
[DCP] connector ...................................................... 9
[ENTER] button ........................................................ 8
[GPI] connector ........................................................ 9
[INPUT PEAK] indicator ........................................... 8
[INPUT SIGNAL] indicator ....................................... 8
[INPUT] connectors ............................................... 10
[NETWORK] indicator .............................................. 8
[OUTPUT SIGNAL] indicator ................................... 8
[OUTPUT] connectors ........................................... 10
[POWER] indicator ................................................... 8
[PRESET] display .................................................... 8
[RC-232C] connector ............................................... 9
[SCHEDULER] indicator .......................................... 8
[SD/ACT] indicator ................................................... 8
[ST IN] connectors ................................................. 10
[UNIT ID] rotary switch ............................................. 9
[YDIF] connector .................................................... 10
[YDIF] indicator ........................................................ 8
L LOCK ..................................................................... 10
M MTX Editor ............................................................... 7
N NETWORK connector ............................................. 9
O online ..................................................................... 15
P PANEL LOCK ........................................................ 10
PC .......................................................................... 10
phantom power ...................................................... 10
Power switch ........................................................... 8
preset ....................................................... 7, 8, 14, 15
project file ........................................................ 14, 15
Q Quick Guide ........................................................... 13
R Rear Panel ............................................................... 9
RESUME ............................................................... 10
S scheduler ............................................................... 16
Alert ................................................................... 8, 21
schematic diagram ................................................ 13
SD memory card ................................................ 8, 18
SD memory card slot ......................................... 8, 18
START UP MODE ................................................. 10
store ....................................................................... 14
subnet mask .......................................................... 13
B Block Diagram ....................................................... 24
U UNIT ID ................................................................ 8, 9
C cable ties ............................................................ 6, 11
UNLOCK ................................................................ 10
Cascade mode ................................................... 7, 13
control panel ............................................................ 7
Controls and Connectors ......................................... 8
W wizard .................................................................... 13
A AC IN connector ...................................................... 9
Y YDIF ........................................................................ 7
D DCP ......................................................................... 7
DIP switch .............................................................. 10
Distribution mode ............................................... 7, 13
E Euroblock plug ......................................... 6, 9, 10, 11
event ...................................................................... 16
F Features ................................................................... 7
Front Panel .............................................................. 8
G Ground screw .......................................................... 9
I
INIT. (INITIALIZE) .................................................. 10
Initializing ............................................................... 18
install ...................................................................... 13
IP address .............................................................. 10
IP SETTING ........................................................... 10
MTX3
Owner’s Manual
25
26 MTX3 Owner’s Manual
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
CAUT I ON
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the product.
The above warning is located on the top of the unit.
IMPORTANT SAFETY INSTRUCTIONS
1
2
3
4
5
6
7
8
9
10
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The
wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11
12
13
14
Only use attachments/accessories specified by the
manufacturer.
Use only with the cart, stand,
tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When
a cart is used, use caution
when moving the cart/apparatus combination to avoid injury
from tip-over.
Unplug this apparatus during lightning storms or
when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
(UL60065_03)
MTX3
Owner’s Manual
27
For details of products, please contact your nearest Yamaha
representative or the authorized distributor listed below.
Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou
au distributeur le plus proche de vous figurant dans la liste suivante.
NORTH AMERICA
CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Scarborough, Ontario,
M1S 3R1, Canada
Tel: 416-298-1311
U.S.A.
Yamaha Corporation of America
6600 Orangethorpe Ave., Buena Park, Calif. 90620,
U.S.A.
Tel: 714-522-9011
CENTRAL & SOUTH AMERICA
MEXICO
Yamaha de México S.A. de C.V.
Av. Insurgentes Sur 1647 “Prisma Insurgentes”,
Col. San José Insurgentes,
Del. Benito Juárez,
03900, México, D.F.
Tel: 55-5804-0600
BRAZIL
Yamaha Musical do Brasil Ltda.
Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi,
CEP 04534-013 Sao Paulo, SP. BRAZIL
Tel: 011-3704-1377
ARGENTINA
Yamaha Music Latin America, S.A.
Sucursal de Argentina
Olga Cossettini 1553, Piso 4 Norte
Madero Este-C1107CEK
Buenos Aires, Argentina
Tel: 011-4119-7000
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha Music Latin America, S.A.
Torre Banco General, Piso 7, Urbanización Marbella,
Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, Panamá
Tel: +507-269-5311
EUROPE
THE UNITED KINGDAM/IRELAND
Yamaha Music Europe GmbH (UK)
Sherbourne Drive, Tilbrook, Milton Keynes,
MK7 8BL, England
Tel: 01908-366700
GERMANY
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
SWITZERLAND/LIECHTENSTEIN
Yamaha Music Europe GmbH
Branch Switzerland in Zürich
Seefeldstrasse 94, 8008 Zürich, Switzerland
Tel: 044-387-8080
AUSTRIA/BULGARIA
Yamaha Music Europe GmbH Branch Austria
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
CZECH REPUBLIC/HUNGARY/
ROMANIA/SLOVAKIA/SLOVENIA
Yamaha Music Europe GmbH
Branch Austria (Central Eastern Europe Office)
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-602039025
POLAND/LITHUANIA/LATVIA/ESTONIA
Yamaha Music Europe GmbH
Branch Poland Office
ul. Wrotkowa 14 02-553 Warsaw, Poland
Tel: 022-500-2925
PA33
Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten
Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen
Bestimmungsländern erhältlich.
Para detalles sobre productos, contacte su tienda Yamaha más
cercana o el distribuidor autorizado que se lista debajo.
MALTA
ASIA
Olimpus Music Ltd.
The Emporium, Level 3, St. Louis Street Msida
MSD06
Tel: 02133-2144
THE PEOPLE’S REPUBLIC OF CHINA
Yamaha Music & Electronics (China) Co.,Ltd.
2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,
Shanghai, China
Tel: 021-6247-2211
THE NETHERLANDS/
BELGIUM/LUXEMBOURG
Yamaha Music Europe Branch Benelux
Clarissenhof 5-b, 4133 AB Vianen, The Netherlands
Tel: 0347-358 040
FRANCE
Yamaha Music Europe
BP 70-77312 Marne-la-Vallée Cedex 2, France
Tel: 01-64-61-4000
PT. Yamaha Musik Indonesia (Distributor)
PT. Nusantik
Gedung Yamaha Music Center, Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: 021-520-2577
Yamaha Music Europe GmbH, Branch Italy
Viale Italia 88, 20020 Lainate (Milano), Italy
Tel: 02-935-771
KOREA
SPAIN/PORTUGAL
Yamaha Music Europe GmbH Ibérica, Sucursal
en España
Ctra. de la Coruna km. 17, 200, 28230
Las Rozas (Madrid), Spain
Tel: +34-902-39-8888
GREECE
Philippos Nakas S.A. The Music House
147 Skiathou Street, 112-55 Athens, Greece
Tel: 01-228 2160
Yamaha Music (Russia)
Room 37, bld. 7, Kievskaya street, Moscow,
121059, Russia
Tel: 495 626 5005
OTHER EUROPEAN COUNTRIES
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: +49-4101-3030
AFRICA
Yamaha Corporation,
Asia-Pacific Sales & Marketing Group
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2303
MIDDLE EAST
TURKEY/CYPRUS
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
Yamaha Music (Malaysia) Sdn., Bhd.
Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,
Petaling Jaya, Selangor, Malaysia
Tel: 03-78030900
TAIWAN
Yamaha Music Europe GmbH, Tyskland – filial
Denmark
Generatorvej 6A, DK-2730 Herlev, Denmark
Tel: 44 92 49 00
RUSSIA
MALAYSIA
Yamaha Music (Asia) PRIVATE LIMITED
Blk 202 Hougang Street 21, #02-00,
Singapore 530202, Singapore
Tel: 6747-4374
Yamaha Music Europe GmbH Germany filial
Scandinavia
J. A. Wettergrens Gata 1, Box 30053
S-400 43 Göteborg, Sweden
Tel: 031 89 34 00
Yamaha Music Europe GmbH Germany Norwegian Branch
Grini Næringspark 1, N-1345 Østerås, Norway
Tel: 67 16 77 70
Yamaha Music Korea Ltd.
8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,
Kangnam-Gu, Seoul, Korea
Tel: 02-3467-3300
SINGAPORE
SWEDEN/FINLAND/ICELAND
NORWAY
Yamaha Music India Pvt. Ltd.
Spazedge building, Ground Floor, Tower A, Sector
47, Gurgaon- Sohna Road, Gurgaon, Haryana, India
Tel: 0124-485-3300
INDONESIA
ITALY
DENMARK
INDIA
Yamaha KHS Music Co., Ltd.
3F, #6, Sec.2, Nan Jing E. Rd. Taipei.
Taiwan 104, R.O.C.
Tel: 02-2511-8688
THAILAND
Siam Music Yamaha Co., Ltd.
4, 6, 15 and 16th floor, Siam Motors Building,
891/1 Rama 1 Road, Wangmai,
Pathumwan, Bangkok 10330, Thailand
Tel: 02-215-2622
OTHER ASIAN COUNTRIES
Yamaha Corporation,
Asia-Pacific Sales & Marketing Group
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2303
OCEANIA
AUSTRALIA
Yamaha Music Australia Pty. Ltd.
Level 1, 99 Queensbridge Street, Southbank,
Victoria 3006, Australia
Tel: 3-9693-5111
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN
Yamaha Corporation,
Asia-Pacific Sales & Marketing Group
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2303
OTHER COUNTRIES
Yamaha Music Gulf FZE
LOB 16-513, P.O.Box 17328, Jubel Ali,
Dubai, United Arab Emirates
Tel: +971-4-881-5868
HEAD OFFICE Yamaha Corporation, Pro Audio Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650
Tel: +81-53-460-2441
Yamaha Pro Audio global web site:
http://www.yamahaproaudio.com/
Yamaha Manual Library:
http://www.yamaha.co.jp/manual/
C.S.G., Pro Audio Division
© 2013 Yamaha Corporation
304POHD*.*-01A2
Printed in China
ZC11300
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement