DISC 4040
DEUTSCH
ENGLISH
FRANÇAIS
NEDERLANDS
DISC 4040
ENVIRONMENTAL PROTECTION
Do not dispose of this product with the normal household waste at the end
of its life cycle. Return it to a collection point for the recycling of electrical
and electronic devices. This is indicated by the symbol on the product,
user manual or packaging.
The materials are reusable according to their markings. By reusing, recycling or
other forms of utilization of old devices you make an important contribution to
the protection of our environment.
Please contact your local authorities for details about collection points.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LASER CLASE 1
CAUTION - INVISIBLE LASER RADIATION WHEN OPENING
THE COVER OR PRESSING THE SAFETY INTERLOCK. AVOID
EXPOSURE TO THE LASER BEAM.
This symbol indicates the presence of dangerous
voltage inside the enclosure, sufficient enough to
cause electric shock.
WARNING
Risk of electric shock
Do not open!
Caution: To reduce the risk of electric shock, do not remove the cover (or back). There
are no user serviceable parts inside. Refer servicing to qualified service personnel.
This symbol indicates the presence of important
operating and maintenance instructions for the
device.
Safety, Environmental and Setup Instructions
•
Use the device in dry indoor environments only.
•
Protect the device from humidity.
•
Do not open the device. RISK OF ELECTRIC SHOCK! Refer opening and servicing to qualified personnel.
•
Connect this device to a properly installed and earthed wall outlet only. Make sure the mains voltage corresponds with
the specifications on the rating plate.
•
Make sure the mains cable stays dry during operation. Do not pinch or damage the mains cable in any way.
•
A damaged mains cable or plug must immediately be replaced by an authorized service center.
•
In case of lightning, immediately disconnect the device from the mains supply.
•
Children should be supervised by parents when using the device.
•
Clean the device with a dry cloth only.
Do NOT use CLEANING AGENTS or ABRASIVE CLOTHS!
•
Do not expose the device to direct sunlight or other heat sources.
•
Install the device at a location with sufficient ventilation in order to prevent heat accumulation.
•
Do not cover the ventilation openings!
•
Install the device at a safe and vibration-free location.
•
Install the device as far away as possible from computers and microwave units; otherwise radio reception may be
disturbed.
•
Do not open or repair the enclosure. It is not safe to do so and will void your warranty. Repairs only by authorized
service/ customer center.
•
The device is equipped with a “Class 1 Laser”. Avoid exposure to the laser beam as this could cause eye injuries.
•
Only use mercury and cadmium-free batteries.
•
Used batteries are hazardous waste and NOT to be disposed of with the household waste!!! Return the batteries to your
dealer or to collection points in your community.
•
Keep batteries away from children. Children might swallow batteries. Contact a physician immediately if a battery was
swallowed.
•
Check your batteries regularly to avoid battery leakage.
Used batteries are hazardous waste and NOT to be disposed
of with the household waste! As a consumer you are legally
obligated to return all batteries for environmentally responsible
recycling – no matter whether or not the batteries contain harmful
substances*).
Return batteries free of charge to public collection points in your
community or to shops selling batteries of the respective kind.
Only return fully discharged batteries.
*) marked Cd = cadmium, Hg = mercury, Pb = lead
WARNING
1. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or
moisture. The apparatus shall not be exposed to dripping or splashing and that no objects filled with
liquids, such as vases, shall not be placed on apparatus.
2. WARNING: The battery (battery or batteries or battery pack) shall not be exposed to excessive heat
such as sunshine, fire or the like.
3. WARNING: Excessive sound pressure from earphones and headphones can cause hearing loss.
4. WARNING: The mains plug is used as disconnect device, the disconnect device shall remain
readily operable.
5. Do not install this equipment in a confined space such as a book case or similar unit.
The ventilation should not be impeded by covering the ventilation openings with items
such as newspaper, table-cloths, curtains etc.
6.
7.
Invisible laser radiation when open and interlocks defeated. Avoid exposure to beam of laser.
Correct Disposal of this product. This marking indicates that this product should not be disposed with
other household wastes throughout the EU. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To
return your used device, please use the return and collection systems or contact the retailer where the product
was purchased. They can take this product for environmental safe recycling.
8. No naked flame sources, such as lighted candles, should be placed on the apparatus.
9. Attention should be drawn to environmental aspects of battery disposal.
10. Use of the apparatus in moderate climates.
WARNING
TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING : SHOCK HAZARD-DO NOT OPEN
LIGHTNING FLASH WITH ARROWHEAD SYMBOL -
EXCLAMATION POINT - within an equilateral triangle,
within an equilateral triangle, is intended to alert the
is used to indicate that a specific component shall be
user to the presence of uninsulated dangerous
replaced only by the component specified in that
voltage within the products enclosure that may be of
documentation for safety reason.
sufficient magnitude to constitude a risk of electric
shock to persons.
The following label has been affixed to the unit, listing the proper procedure for working with the laser beam:
CLASS 1 LASER PRODUCT LABEL CLASS 1 LASER PRODUCT
KLASS 1 LASER APPARAT
LUOKEN 1 LAISERLAITE
KLASSE 1 LASER PRODUKT
This label is attached to the place as illustrated to inform that the
apparatus contains a laser component.
WARNING LABEL INFORMING OF RADIATION This label is placed inside the unit. As shown in the illustration. To
warn against further measures on the unit. The equipment contains
a laser radiating laser rays according to the limit of laser product of
class 1.
E-1
SAFETY INSTRUCTIONS
1. READ INSTRUCTIONS - All the safety and operating instructions should be read before the appliance is operated.
2. RETAIN INSTRUCTIONS - The safety and operating instruction should be retained for future reference.
3. HEED WARNINGS - All warnings on the appliance and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS - All operating instructions should be followed.
5. WATER AND MOISTURE - The appliance should not be used near water, for example, near a bathtub, washbowl,
kitchen sink, laundrytub, swimming pool or in a wet basement.
6. VENTILATION - The appliance should be situated so that its location or position does not interfere with its proper
ventilation. Do not place on bed, sofa, rug or similar surface that may block the ventilation openings, in a built-in
installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.
7. HEAT - The appliance should be situated away from heat sources such as radiators, stoves, or other appliances
(including amplifiers) that produce heat.
8. POWER SOURCE - The appliance should be connected to power supply only of the type described in the
operating instructions or as marked on the appliance.
9. GROUNDING - Precautions should be taken to ensure that the grounding means of an appliance is not defeated.
10. POWER CORD PROTECTION - Power supply cords should be routed so that they are not likely to be walked
on or pinched by items placed upon or against them.
11. POWER LINES - An outdoor antenna should be located away from power lines.
12. OBJECT and LIQUID ENTRY - Care should be taken so that objects do not fall and liquids are not spilled into
the enclosure through openings.
13. ESD WARNING - The display does not function properly or no reaction to operation of any the control may due
to the electrostatic discharge. Switch off and unplug the set. Reconnect after a few seconds.
14. DAMAGE REQUIRING SERVICE - The appliance should be serviced by qualified service personnel when:
a. The power-supply cord or plug has been damaged.
b. Objects have fallen into, or liquid has been spilled into the appliance enclosure.
c. The appliance has been exposed to rain.
d. The appliance has been dropped, or the enclosure damaged.
e. The appliance does not appear to operate normally.
15. SERVICING - The user should not attempt to service the appliance beyond that described in the user operating
instructions. All other servicing should be referred to qualified service personnel.
Notes:
a. Dirty or scratched CD may cause a skipping problem. Clean or replace the CD.
b. If an error display or malfunction occurs, disconncet the AC cord and remove all the batteries. Then turn the power
back on.
BEFORE OPERATION
Notes: CONCERNING COMPACT DISCS.
Since dirty, damaged or warped discs may damage the appliance, care should be taken of the followings items:
a. Usable compact discs. Use only compact disc with the mark shown below.
b. CD compact disc only with digital audio signals.
E-2
LOCATION OF CONTROL
19
1
2
18
17
16
15
14
13
12
3
4
5
6
7
8
9 10 11
20
21
28
27
22
26
25
23
24
1. LCD DISPLAY
2. REMOTE SENSOR
3. STANDBY
4. TIME
5. HOUR
6. MINUTE
7. VOLUME 8. SKIP 9. SKIP +
10. STOP
11. PLAY / PAUSE
12. VOLUME +
13. MODE
14. PROGRAM
15. ALBUM +
16. EJECT
17. SD CARD SLOT
18. USB SLOT
19. CD DOOR
20. FM ANTENNA
21. BAND SELECTOR
22. TUNING CONTROL
23. BATTERY BACKUP
24. AC CORD
25. PHONES JACK
26. AUX IN
27. BASS SELECTOR
28. FUNCTION SELECTOR
POWER SOURCE
AC POWER
You can power your appliance by plugging the AC power cord at the back of the appliance into a wall
AC power outlet. Check that the rated voltage of your appliance matches your local voltage.
E-3
REMOTE CONTROL
1. STANDBY
2. STOP
7
3. SKIP +
1
8
5. VOLUME -
2
9
6. SKIP -
3
4
5
10
4. PLAY/PAUSE
7. MODE
8. OPEN/CLOSE
9. ALBUM +
6
10. VOLUME +
BATTERY INSTALLATION
Insert a “Cell” size batteries into the battery compartment. Be sure that the batteries are inserted
correctly to avoid damage to the remote control. Always remove the batteries when the remote
control will not be used for a long period of time, as this will cause leakage to the batteries and
subsequently damage to your set.
INSTALLING BATTERIES
+
Slide out cover and install single “Cell” battery
with polarities as shown
Notes:
- If the distance required between the remote control and the appliance decreases, the batteries
are exhausted. In this case replace the batteries with new one.
- Power button on main unit must be ‘On’ in order for Remote Control to operate.
SENSOR WINDOW OF THE RECEIVER
- Even if the remote control is operated within the effective range, its operation may be impossible if
there are any obstacies between the appliance and the remote control.
- If the remote control is operated near other appliances which generate infrared rays, or if other
remote control devices using infrared rays are used near the appliance, it may operate incorrectly.
E-4
RADIO OPERATION
GENERAL OPERATION
1.
2.
3.
4.
Set the “FUNCTION” selector to “RADIO” mode.
Select desired band by using the “BAND” selector.
Adjust radio frequency to your desired station by using the “TUNING” control.
Adjust the “VOLUME” control to the desired level.
FM / FM-STEREO RECEPTION
- Set the “BAND” selector to FM mode for MONO reception.
- Set the “BAND” selector to FM ST. mode for FM STEREO reception. The Stereo indicator light up
to show FM ST. mode.
FOR BETTER RECEPTION
FM - This appliance has a FM antenna located at the rear cabinet. This wire is completely unraveled
and extended for better reception.
AM - This appliance is equipped with a built - in directional ferrite AM antenna. Rotate the appliance
to get better reception.
E-5
CD / MP3 OPERATION
GENERAL OPERATION
PLAY / PAUSE
Press to start playing CD / MP3 disc.
Press again to stop playing CD / MP3 operation temporarily.
Press again to resume playback.
SKIP +
SKIP -
Press to go to the next track or back to the previous track.
Press and hold while playing until you find the point of the sound.
&
STOP
Press to stop all CD / MP3 operation.
EJECT
Press to open / close the CD door.
PLAYBACK
1.
2.
3.
4.
5.
6.
7.
8.
Set the “FUNCTION” selector to “CD” mode.
Open the CD door and place a CD / MP3 disc with the label up in the CD compartment.
Close the CD door.
Focus search is performed if disc is inside. Total number of tracks is read and appears on the
display.
Playbak will start automatically from the first track.
Adjust the “VOLUME” control to the desired level.
Press the “PLAY / PAUSE” button again when you want to stop temporarily.
Press the “STOP” button when finished.
E-6
CD / MP3 OPERATION
PROGRAM
Be sure to press the “STOP” button before use.
1. Press the “PROGRAM” button, the display will show “P01” and flash.
2. Select desired track by using the “SKIP +” or “SKIP -” button. ( You may select a desired album by
pressing “ALBUM +” button. )
3. Press the “PROGRAM” button again to confirm desired track into the program memory.
4. Repeat step 2 and 3 to enter additional tracks into the program memory.
5. When all the desired tracks have been programmed, press the “PLAY / PAUSE” button to
play the disc in the order you have programmed.
6. Press the “STOP” button twice to terminate programmed playback.
MODE
Press the “MODE” button during playing CD / MP3 disc,
each press switches the mode function as follows:
1 - REPEAT 1
2 - REPEAT ALBUM ( *MP3 ONLY )
3 - REPEAT ALL
4 - RANDOM
5 - NORMAL PLAYBACK
REP
REP
ALBUM
REP
ALL
REPEAT 1
REPEAT
ALBUM
REPEAT
ALL
RAND
NORMAL
PLAYBACK
E-7
RANDOM
USB / SD OPERATION
GENERAL OPERATION
PLAY / PAUSE
Press to start playing tracks from the USB / SD card.
Press again to stop playing USB / SD operation temporarily.
Press again to resume playback.
SKIP +
SKIP -
Press to go to the next track or back to the previous track.
Press and hold while playing until you find the point of the sound.
&
STOP
Press to stop all USB / SD operation.
PLAYBACK
1.
2.
3.
4.
5.
Plug or slot in USB / SD card device to the port. (Make sure no disc on disc tray)
Set the “FUNCTION” selector to “CD” mode.
Playback will start automatically from the first track.
Press the “STOP” button when finished.
Press the “PLAY / PAUSE” button again, playback will start from the first track.
Remark
- If have disc on disc tray, press and hold the “PLAY / PAUSE” button for a few seconds to entry
USB / SD mode.
- Press and hold the “STOP” button for a few seconds to choose playing USB or SD card.
PROGRAM, MODE
The operation of PROGRAM, MODE are as the same as that of CD / MP3. Please refer to CD / MP3
OPERATION.
OTHER FEATURES
CLOCK SETTING
To adjust clock setting, make sure in CD mode.
1. Press the “TIME SET” button. (Do not release “TIME SET” button during time setting)
2. Press the “HOUR” button to set hour.
3. Press the “MIN” button to set minute.
4. Release all button to confirm setting. Confirmed setting will on the display.
E-8
CLEANING AND MAINTENANCE
• Always remove the mains plug before cleaning the machine.
• Any marks on the surface can be wiped off with a slightly damp cloth without any additives.
NOTE: COMPACT DISKS
• This device is able to play CDs with a diameter of 8 cm and 12 cm.
NOTE:
Only place one disc in the CD compartment at a time.
• Only audio CDs, CD-R and CD-RW disks can be played on this machine.
• Always place the CD into the CD compartment with the label facing upwards. Compact discs can
only be played on one side.
• Fingerprints and dust should be carefully removed from the recorded side of the CD (the side
without the label) with a soft cloth. Wipe off in straight lines from the centre to the edge.
• After being played, CDs should be returned to their case so that they do not become scratched.
• Do not expose CDs to direct sunlight, high humidity levels or prolonged high temperatures in order
to prevent them from warping.
• Do not adhere any paper to the CD or write on it.
• Do not spray any cleaning agents or antistatic sprays on to the CD as in the case of phonographs.
TROUBLESHOOTING
Symptoms
CD can not be
played back.
Course
CD is not inserted
or inserted incorrectly.
CD jumps during
playback.
Check the disc for
fingerprints, dirt or
scratches.
Solution
Ensure that the
disc is inserted with
the label facing
upwards.
Check the disc for
fingerprints, dirt or
scratches.
TECHNICAL DATA
Model:...................................DISC 4040
Power supply:.......................230V~50Hz
Power consumption:............ 21W
Radio section:
Frequency ranges............UKW / FM 87.5 ~ 108.0 MHz
............MW / AM 540 ~ 1600 KHz
E-9
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement