SV-SFPP-10GT1-T1-XM
SV-SFPP-10GT1-T1-XM
SFP+ Direct Attach Cables , 1m、3m、5m、7m、10m Reach
Features
• Support for multi-gigabit data rates up to 10.5Gbps
• Data rates backward compatible to 1Gbps
• Support for 1x, 2x, 4x and 8x Fibre Channel data rates
• Hot-pluggable SFP 20PIN footprint
• I/O Connector designed for high speed differential
signal applications
• Improved Pluggable FormFactor(IPF) compliant for
enhanced EMI/EMC performance
• Low Power Consumption < 0.5W
Applications
• Power Supply :+3.3V
•
• Compatible to SFP+ MSA
• Temperature Range: 0 to +70°C
•
• RoHS Compatible
•
•
High capacity I/O in Storage Area
Networks, Network Attached Storage,
and Storage Servers
Switched fabric I/O such as ultra high
bandwidth switches and routers
Data center cabling infrastructure
High density connections between
networking equipment
Product Description
The SFP+ cable assemblies are high performance ,cost effective I/O solution for 10Gb
Ethernet and 10G fiber
Channel applications. SFP+ copper modules allow hardware manufactures to achieve high
port density, configurability and utilization at a very low cast and reduced power budget.
The high speed cable assemblies meet and exceed Gigabit Ethernet and Fibre Channel
industry standard requirements for performance and reliability..
Recommended Operating Conditions
Parameter
Symbol
Max
Unit
-40
+85
°C
Tc
0
+70
°C
Vcc3
3.14
3.47
V
0.5
W
Storage Ambient Temperature
Operating Case Temperature
Power Supply Voltage
Power Dissipation
1
Min
PD
www.starviewint.com
Typical
3.3
SV-SFPP-10GT1-T1-XM
SFP+ Direct Attach Cables , 1m、3m、5m、7m、10m Reach
Systems
10.5 Gpbs line speed, full duplex
Bit error rate: better than 10E-12
Performance
Hot-pluggable, industry-standard Small Form-Factor
Pluggable(SFP+) copper cable, available as 1m,3m or 5m.
Media
Supply voltage: 3.3V
Power consumption(per end): max 0.5W
Operating Parameters
Supported Length
1m, 3m, or 5m typical & customer specific requirements
Pin Descriptions
Pin
Logic
Symbol
Description
VEET
Transmitter Ground
2
LV-TTL-O
TX_FAULT
N/A
Note 1
3
LV-TTL-I
TX_DISABLE
Transmitter Disable
Note 2
4
LV-TTL-I/O
SDA
Two Wire Serial Data
5
LV-TTL-I
SCL
Two Wire Serial Clock
MOD_DEF(0)
Module present, Connect to VeeT
1
6
Notes
7
LV-TTL-I
RS0
N/A
Note 1
8
LV-TTL-O
LOS
Loss of Signal
Note 2
9
LV-TTL-I
RS1
N/A
Note 1
10
VEER
Receiver ground
11
VEER
Receiver ground
12
CML-O
RD-
Received Data Inverted
13
CML-O
RD+
Received Data Non- Inverted
14
VEER
Receiver ground
15
VCCR
Receiver Supply 3.3V
16
VCCT
Transmitter Supply 3.3V
17
VEET
Transmitter Ground
TD+
Transmit Data Non-Inverted
TD-
Transmit Data Inverted
VEET
Transmitter Ground
18
CML_O
19
CML_O
20
Notes:
1. Signals not supported in SFP+ Copper pulled-down to VeeT with 30K ohms resistor
2. Passive cable assemblies do not support LOS and TX_DIS
2
www.starviewint.com
SV-SFPP-10GT1-T1-XM
SFP+ Direct Attach Cables , 1m、3m、5m、7m、10m Reach
Ordering Information
Part number
Data Rate
Distance
Temperature
SV-SFPP-10GT1-T1-1M
10GSFP+Cu
1m
0ºC ~ +70ºC
SV-SFPP-10GT1-T1-3M
3m
0ºC ~ +70ºC
SV-SFPP-10GT1-T1-5M
10GSFP+Cu
10GSFP+Cu
5m
0ºC ~ +70ºC
SV-SFPP-10GT1-T1-7M
10GSFP+Cu
7m
0ºC ~ +70ºC
SV-SFPP-10GT1-T1-10M
10GSFP+Cu
10m
0ºC ~ +70ºC
3
www.starviewint.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising