Digital Scale Bluetooth® Wireless Solutions

Digital Scale Bluetooth® Wireless Solutions
Digital Scale
Bluetooth® Wireless Solutions
BLUETOOTHONE/BLUETOOTHONEWA/
BLUETOOTHONEWA-L
User Instructions
Correction of Errors and Inaccuracies. The Content may contain typographical errors or other errors or
inaccuracies and may not be complete or current. Health o meter® Professional therefore reserves the right to
correct any errors, inaccuracies or omissions and to change or update the Content at any time without prior notice.
Health o meter® Professional does not, however, guarantee that any errors, inaccuracies or omissions will be
corrected.
P/N UMBLUETOOTHONE_WA REV20170628
1
Thank you for your purchase of this Health o meter® Professional product. Please read this
manual carefully, and keep it for easy reference or training.
TABLE OF CONTENTS
CAUTIONS AND WARNINGS .................................................................................................... 3
WELCH ALLYN® CONNEX/LXI REQUIREMENTS ............................................................... 3
WINDOWS® PC REQUIREMENTS ............................................................................................ 3
SERVICE ........................................................................................................................................ 3
PACKAGE CONTENTS ................................................................................................................ 4
BLUETOOTHONE PRODUCT OVERVIEW .............................................................................. 5
BLUETOOTHONEWA PRODUCT OVERVIEW........................................................................ 6
BLUETOOTHONEWA-L PRODUCT OVERVIEW…………………………………………….7
HARDWARE INSTALLATION - STEP 1 (FOR CONNEX, LXI AND PC USE) ...................... 8
HARDWARE INSTALLATION - STEP 2 (FOR CONNEX) .................................................... 10
HARDWARE INSTALLATION – STEP 2 (FOR LXI) .............................................................. 11
HARDWARE/DRIVER INSTALLATION STEP 2 (FOR SCALE COMMUNICATION
TO WINDOWS® PC) .................................................................................................................. 13
BLUETOOTH® LINK COMMUNICATION - STEP 3 (FOR CONNEX, LXI AND PC USE) 18
TROUBLESHOOTING - RS232 BLUETOOTH® ADAPTER .................................................. 20
TROUBLESHOOTING - USB BLUETOOTH® DONGLE ....................................................... 22
TROUBLESHOOTING - WELCH ALLYN® CONNEX ........................................................... 23
LIMITED WARRANTY .............................................................................................................. 24
FEDERAL COMMUNICATION COMMISSION (FCC) STATEMENT .................................. 25
BLUETOOTH® CERTIFICATION ............................................................................................ 26
CE CERTIFICATION .................................................................................................................. 26
2
Cautions and Warnings

To prevent installation and performance issues to your PC, please follow these
instructions carefully.

For accurate data collection, confirm and upload the data according to the
procedure described in this manual.

Data validation must be confirmed by the user from the scale to the receiving
device to ensure accurate data collection.
Welch Allyn® Connex/LXi Requirements

Health o meter® Professional scale Weight, Height and Body Mass Index (BMI)
data communication via Bluetooth® requires the Bluetooth One unit.
Windows® PC Requirements





This installation is exclusively compatible with Windows® XP/Vista/7
CPU of 1.7GHz and above
Minimum 512MB RAM
Windows XP/Vista/7
Available USB 2.0 Port
Service


For support, please Customer Service at: Toll Free: 1.800.815.6615 (US & Canada only)
Email: [email protected]
3
Package Contents
BLUETOOTHONE
(This kit is for facilities that already own a HOMWA connectivity kit adapter and want to
connect to Welch Allyn® Connex Spot, CVSM or Connex Integrated Wall Systems or LXi
monitors. This kit can also be used to connect to Allscripts™ or Midmark® IQ Manager® via a
Windows® PC)
o 1 x HOMBT1 Scale Unit
o RS232 Bluetooth® Adapter (already connected to HOMBT1 Scale Unit, see Figure 1)
o 1 x USB Bluetooth® Dongle
o 1 x SCALE CABLE (1 ft. USB cable)
o 1 x POWER CABLE (6 ft. USB cable)
o 1 x AC to USB Wall Power Adapter
o 1 x Welch Allyn® Connex Vital Signs Monitor (CVSM) Quick Start Guide
o 1 x Welch Allyn® Spot Vital Signs LXi Quick Start Guide
o 1 x User Instructions
BLUETOOTHONEWA
(This kit includes all of the items listed in the BLUETOOTHONE kit, along with the following
additional items.)
o 1 x HOMWA (black box)
o 1 x USB Cable 1 ft.
o 1 x USB Cable 6 ft.
BLUETOOTHONEWA-L
(This kit includes all of the items listed in the BLUETOOTHONE kit, along with the following
additional items.)
o 1 x HOMWA (blue box)
o 1 x RS232 Cable 5 ft.
o 1 x USB Cable 1 ft.
4
BLUETOOTHONE Product Overview
1. HOMBT1 Scale Unit (Yellow Label)
2. RS232 Bluetooth® Adapter
3. SCALE CABLE (1 ft. USB cable)
4. AC to USB Wall Power Adapter
(Note: color and shape of power adapter may vary)
5. POWER CABLE (6 ft. USB cable)
2
1
3
5
4
Figure 1
6. USB Bluetooth® Dongle
Figure 2
5
BLUETOOTHONEWA Product Overview
1. HOMWA Unit (Black Box with White
Label)
2. USB Cable 1 ft.
3. USB Cable 6 ft.
4. CVSM Scale Activation Code
1
2
7
7
Figure 4
Figure 3
3
4
2
2
7
7
Figure 6
Figure 5
Note: The BLUETOOTHONEWA unit includes the BLUETOOTHONE unit items listed on the
previous page.
6
BLUETOOTHONEWA-L Product Overview
1. HOMWA Unit (Blue Box with White
Label)
2. USB Cable 1 ft.
3. RS232 Cable 5 ft.
1
2
7
7
Figure 7
Figure 8
3
2
7
Figure 9
Note: The BLUETOOTHONEWA-L unit includes the BLUETOOTHONE unit items listed on
page 5.
7
Hardware Installation - Step 1 (for Connex, LXi and PC use)
®
1. Using the SCALE CABLE (1 ft. USB cable), connect the Health o meter Professional scale
USB port to the “TO SCALE” USB port on the HOMBT1 Scale Unit as the following
figure.
2. Connect POWER CABLE (6 ft. USB cable) to AC to USB Wall Power Adapter, and then
connect other end to the HOMBT1 Scale Unit “Power In” USB Port. (Note: This is only to
provide power to the HOMBT1 Scale Unit)
Scale USB Port
TO SCALE
HOMBT1 Scale Unit
Yellow Label
SCALE UNIT - Connected to scale
by adhesive label with Velcro®
POWER IN - Connected to AC to
USB Wall Power Adapter
Figure 10
3. Connect the AC to USB Wall Power Adapter to a wall power outlet as the following figure.
Or if a Powered USB 2.0 Port or Powered USB 2.0 Hub is available, connect the USB cable
to the port/hub.
Note: Color and shape
of the AC to USB wall
power adapter may vary
Figure 11
4. Utilizing the Velcro adhesive, secure the HOMBT1 Scale Unit to the scale.
8
Hardware Installation - Step 2
The Bluetooth® Wireless Solution allows for the scale to interface wirelessly with Welch Allyn
Connex® Spot Monitors, Connex® Vital Signs Monitors, Connex® Integrated Wall Systems,
and Spot Vital Signs® LXi monitors. Users can also connect wirelessly with a Windows® PC to
interface with Allscripts TouchWorks® and Professional™ systems and Midmark® IQ
Manager® software.
 For connecting to Welch Allyn Connex® Vital Signs Devices, see page 10.
 For connecting to Welch Allyn Spot Vital Signs® LXi monitors, see pages 1112.
 For connecting to a Windows® PC, see pages 13 -17.
9
Hardware Installation - Step 2 for Connex
The following instructions illustrate the hardware installation for connecting to a Welch Allyn
Connex Vital Signs Monitor (CVSM). USB ports on the Connex Spot and Integrated Wall Systems
are located on the underside of the monitor.
1. Connect the USB Bluetooth® Dongle to the HOMWA unit as the following figure.
HOMWA Unit
Black Box
with White Label
Connect the USB Bluetooth®
Dongle to the “TO SCALE” USB
Port on the HOMWA unit
Figure 12
2. Connect the HOMWA to the Welch Allyn® CVSM as the following figure.
HOMWA Unit Connection to
CVSM
1) Using the 1 ft. USB cable,
connect the USB cable to any
available USB port on the
Welch Allyn® CVSM
Welch Allyn® CVSM
2) Connect the other end of the 1
ft. USB cable to the “TO
CONNEX DEVICE” USB
port on the HOMWA unit
Figure 13
3. Power on the CVSM unit and power on the scale to initialize Bluetooth® communication.
Continue to page 18 for Step 3 - Bluetooth® Link Communication instructions.
Note: The set up presumes that the BLUETOOTHONE unit has been has been set up
previously to the scale, see Step 1 on page 8.
10
Hardware Installation – Step 2 for LXi
1. Connect the USB Bluetooth® Dongle to the HOMWA unit as in the following figure.
HOMWA Unit
Blue Box with
White Label
Connect the USB Bluetooth®
Dongle to the “TO SCALE” USB
Port on the HOMWA unit
Figure 14
2. Connect the D-Sub Cable female end to the “TO LXI” port on the HOMWA unit.
Welch Allyn® Spot Vital Signs LXi
LXi Power Button
Connect RS232 cable to
“TO LXI” port on HOMWA
unit
USB Bluetooth® Dongle
connected to “TO SCALE”
USB port on HOMWA unit
Figure 15
11
Hardware Installation – Step 2 for LXi
3. Connect the RS232 cable male end from the HOMWA unit to the “I” port on the back of
the LXi.
Back side of LXi
Connect RS232 cable from
HOMWA unit to the LXi “I”
port
Figure 16
4. Power on the LXi unit and power on the scale to initialize Bluetooth® communication.
Continue to page 18 for Step 3 - Bluetooth® Link Communication instructions.
Note: The LXi will only display Weight Readings that are greater than ~11.0lb (5.0Kg).
The LXi will NOT display Height or Body Mass Index (BMI).
Note: The set up presumes that the BLUETOOTHONE unit has been has been set up
previously to the scale, see Step 1 on page 8.
12
Hardware/Driver Installation Step 2 (for Scale
Communication to Windows® PC)
1. Download the CP210x USB to UART Bridge VCP Driver from the following website
or search the internet for key word “CP2102 Driver Download”.
2. http://www.silabs.com/products/mcu/pages/usbtouartbridgevcpdrivers.aspx
3. Alternative download from http://www.silabs.com/ Search for “CP2102 Driver
Download”.
4. Download for Windows® XP/Server 2003/Vista/7/8/8.1 (6.7) – Version 6.7 or the latest
version available.
5. Unzip the downloaded file if necessary

The following example shows installation for a Windows 64 bit OS.
Figure 17

Follow the installation wizard steps. Click the “Next” button.
Figure 18
13
Hardware/Driver Installation Step 2 (for Scale
Communication to Windows® PC)

Accept the license agreement and click “Next”
Figure 19

Please wait while the driver installs.
Figure 20
14
Hardware/Driver Installation Step 2 (for Scale
Communication to Windows® PC)

Driver installation is now complete. Click the “Finish” button to close the installation
Wizard.
Figure 21
15
Hardware/Driver Installation Step 2 (for Scale
Communication to Windows® PC)
6. Connect the USB Bluetooth® Dongle to any available USB 2.0 port on the Windows®
PC as the following figure.
Figure 22
7. Open Windows® “Device Manager” and check that the USB Bluetooth® Dongle was
recognized by the Windows® OS as the following figure.
Figure 23
16
Hardware/Driver Installation Step 2 (for Scale
Communication to Windows® PC)
8. Driver installation working properly will be indicated by the illuminated “Orange” LED
on the USB Bluetooth® Dongle as the following figure.
USB Bluetooth® Dongle
Status LED
Solid Orange = Windows
PC Communication Active.
Off = PC Communication
NOT Active*.
Figure 24
9. The driver installation is now ready to communicate with the following applications,
Allscripts™ App, Midmark IQ Manager® Software or Software Development Kit 2.0
(SDK 2.0). Please consult the user instructions for the specific applications that you’re
using.
10. Power on the scale to initialize Bluetooth® communication.
Continue to page 18 for Step 3 - Bluetooth® Link Communication instructions.
Note: The set up presumes that the BLUETOOTHONE unit has been has been set up
previously to the scale, see Step 1 on page 8.
17
Bluetooth® Link Communication - Step 3 (for Connex, LXi and PC use)
NOTE: THE SERIAL NUMBER ON THE BLUETOOTH® DONGLE MUST MATCH
THE SERIAL NUMBER ON THE YELLOW LABEL OF THE HOMBT1 SCALE
UNIT TO ENABLE ACTIVE BLUETOOTH® LINK COMMUNICATION.
®
HOMBT1 SCALE UNIT
BLUETOOTH DONGLE
SERIAL NUMBERS MUST MATCH
®
TO ENABLE BLUETOOTH
COMMUNICATION.
Figure 25
1. Power on the scale and Welch Allyn monitor or PC. To check that the Bluetooth® One
unit has established Bluetooth® communication link, observe that the status LEDs are
illuminated as the following figure.
Power LED
Bluetooth® Status LED
Solid Red = Active Power
Solid Blue = Active,
Bluetooth® Link
Communication.
Blinking Red = Power
Supply Low*
Blinking Blue = NO Active,
Bluetooth® Link
Communication*
Off = No Power*
Figure 26
Note: When Adapter is attached to scale you will be viewing the device upside down.
18
Bluetooth® Link Communication - Step 3 (for Connex, LXi and PC use)
2. Check that the Bluetooth® Dongle status LED is illuminated as the following figure.
USB Bluetooth® Dongle Status LED
Orange = Power On/USB Active
Solid Green = Active Bluetooth® Link
Communication.
Off = NO Active Bluetooth® Link
Communication*
Figure 27
3. If all lights confirm active communication, the devices are now ready to wirelessly
transmit data from the scale to the Welch Allyn monitor or designated PC.
If experiencing a problem, please read the troubleshooting guide on page 22 for
further assistance.
19
Troubleshooting - RS232 Bluetooth® Adapter
NOTE: THE SERIAL NUMBER ON THE BLUETOOTH DONGLE MUST MATCH
THE SERIAL NUMBER ON THE YELLOW LABEL OF THE HOMBT1 SCALE
UNIT TO ENABLE ACTIVE BLUETOOTH® LINK COMMUNICATION.
®
HOMBT1 SCALE UNIT
BLUETOOTH DONGLE
SERIAL NUMBERS MUST MATCH
TO ENABLE BLUETOOTH®
COMMUNICATION.
Figure 28
RS232 Bluetooth® Adapter LED Indicators
LED Indicators
LED Color
Status
On
Off
Power
Red
Blinking
On
Status
Blue
Blinking
Description
Power On
Power Off/ Device Error
Power Supply Low
Active Bluetooth®
Communication
No Active Bluetooth®
Communication
Status LED
Status LED
Blue LED
Red LED
Figure 29
Note: When Adapter is attached to scale you will be viewing the device upside down.
20
Troubleshooting - RS232 Bluetooth® Adapter
RS232 Bluetooth® Adapter Fault Symptoms
Problem
Possible Cause
No Power
Check USB/Battery – DB9Pin 9(5V) switch position
Check that switch is set to DB9Pin9(5V) position setting
Check DCE(F)/DTE switch
position
Check that switch is set to DTE
position setting
Serial Number on Bluetooth®
Dongle does not match Serial
Number on HOMBT1 Scale
Unit
No
Communication
Suggested Action
RS232 Bluetooth® Adapter
out of communication range
Wireless network interference
Bluetooth Radio
21
Check that the Serial Number on
yellow label of HOMBT1 Scale
Unit matches the Serial Number
on the Bluetooth® Dongle. If
they do not match contact
Health o meter Professional
Customer Service at 1-800-8156615.
Check that the distance between
the scale and the Connex device,
LXi or PC is less than ~328ft
(100m)
Move the scale or Connex
device away from other
WiFi/Bluetooth® devices nearby
Re-cycle power to the HOMBT1
Scale Unit by disconnecting the
USB cable connected to
“POWER IN” and
re-connecting
Troubleshooting - USB Bluetooth® Dongle
USB Bluetooth® Dongle LED Indicators
LED Indicators
LED Color
Status
On
Power/USB
Orange
Off
On
Status
Green
Off
Description
Power On/USB Active
Power Off/USB Error
Active Bluetooth®
Communication
NO Active Bluetooth®
Communication
Orange LED
Green LED
Figure 30
USB Bluetooth® Dongle Fault Symptoms
Problem
Possible Cause
No Power/USB
Suggested Action
Re-cycle power to the HOMWA by
disconnecting the USB cable connected to
“TO CONNEX DEVICE” and reconnecting
Check that the distance between the scale
and Connex device, LXi or PC is less than
~328ft (100m)
Check that the Serial Number on yellow label
of HOMBT1 Scale Unit matches the Serial
Number on the Bluetooth® Dongle. If they do
not match contact Health o meter Professional
Customer Service at 1-800-815-6615.
Power failure or USB
error failure
USB Bluetooth®
Dongle out of
communication range
Serial Number on
Bluetooth® Dongle does
not match Serial Number
on HOMBT1 Scale Unit
No
Communication
Wireless network
interference
Move scale or Connex device away from
other WiFi/Bluetooth® devices nearby
Re-cycle power to the HOMWA by
disconnecting the USB cable connected to
“TO CONNEX DEVICE” and reconnecting
Check that the Virtual Comport CP210x
Driver Installation is installed properly
via Windows® Device Manager. Re-install
Driver if necessary
HOMWA to Connex
Device
USB Bluetooth® to
Windows® PC
22
Troubleshooting - Welch Allyn® Connex
Welch Allyn® CVSM
Problem
Possible Cause
No Weight, Height, Body
Mass Index (BMI)
Displayed on CVSM
touch screen
CVSM NOT
activated with
scale Activation
Code
Suggested Action
Via the Welch Allyn® Servicing
Tool, use the provide Activation
Code on the yellow paper to activate
the scale option on the CVSM. For
assistance with the Welch Allyn®
Servicing Tool, please contact a
Welch Allyn® representative or
visit http://www.welchallyn.com/
Figure 32
Figure 31
23
Limited Warranty
IN NO EVENT SHALL THE DIRECT VENDOR'S LIABILITY FOR DIRECT,
INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING
FROM THE USE OF THE PRODUCT, DISK, OR ITS DOCUMENTATION EXCEED
THE PRICE PAID FOR THE PRODUCT.
The direct vendor makes no warranty or representation, expresses, implied, or statutory with
respect to the contents or use of this documentation, and especially disclaims its quality,
performance, merchantability, or fitness for any particular purpose. The direct vendor also
reserves the right to revise or update the device or documentation without obligation to notify
any individual or entity of such revisions, or updates.
What does the Warranty Cover?
This Health o meter® Professional products is warranted from date of purchase against defects of materials or in workmanship for
a period of one (1) year. If the manufacturer determines that a defect of material or in workmanship exists, the customer’s sole
remedy will be replacement of the product at no charge. Replacement will be made with a new or remanufactured product or
component. If the product is no longer available, replacement may be made with a similar product of equal or greater value. All
replaced parts are covered only for the original warranty period.
Who is Covered?
The original purchaser of the product must have proof of purchase to receive warranty service. Please save your invoice or
receipt. Pelstar dealers or retail stores selling Pelstar products do not have the right to alter, or modify or in any way change the
terms and conditions of this warranty.
What is Excluded?
Your warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or misuse
of the product, use on improper voltage or current, use contrary to the operating instructions, abuse including tampering, damage
in transit, or unauthorized repair or alternations. Further, the warranty does not cover natural disasters, such as fire, flood,
hurricanes and tornadoes. This warranty gives you specific legal rights, and you may also have other rights that vary from
country to country, state to state, province to province or jurisdiction to jurisdiction.
To get Warranty Service make sure you keep your sales receipt or document showing proof of purchase. Call (+1) 800638-3722 or (+1) 708-377-0600 to obtain a replacement product.
PELSTAR, LLC
th
9500 West 55 Street • McCook, IL 60525 • USA
1-800-815-6615 or 1-708-377-0600
®
Health o meter is a registered trademark of Sunbeam Products, Inc. used under license.
Health o meter® Professional products are manufactured, designed, and owned by Pelstar, LLC.
We reserve the right to improve, enhance, or modify Health o meter ® Professional product features or specifications without
notice.
© Pelstar, LLC 2017
24
Federal Communication Commission (FCC) Statement
RS232 Bluetooth® Adapter
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try correcting the interference by one or more of the following measures:
- Reorient the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into and outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: A shielded-type power cord is required in order to meet FCC emission limits and also to prevent
interference to the nearby radio and television reception. It is essential that only the supplied power cord be used.
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance
could void your authority to operate the equipment.
Declaration:
1. The information contained in this document is subject to change without notice.
FCC ID: XJ8-BT 232B
CCAB09LP2610T2
25
CE1177
Federal Communication Commission (FCC) Statement
USB Bluetooth® Dongle
RADIO FREQUENCY INTERFERENCE STATEMENT
This module has been tested and found to comply with the FCC part 15 and IC RSS-210 rules. These limits are
designed to provide reasonable protection against harmful interference in approved installations. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference may not occur in a particular installation. This device complies with part 15 of the FCC rules. Operation
is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
Modifications or changes to this equipment not expressly approved by the part responsible for compliance may
render void the user’s authority to operate this equipment.
Modular Approval, FCC and IC


FCC ID: X3ZBTMOD3
IC: 8828A-MOD3
In accordance with FCC part 15, the SPT2632C1A.AT2 is listed above as a modular transmitter device.
Bluetooth® Certification
USB Bluetooth® Dongle
Module with embedded stack and profile has been qualified according to SIG qualification rules:
– Bluetooth® SIG qualified design, QD ID: B019224
– Product type: end product
– TGP version: Core 3.0
– Core spec version: 3.0
– Product descriptions: Bluetooth® module, spec V3.0
CE Certification
USB Bluetooth® Dongle
Module has been certified according to following certification rules:
– CE Expert opinion: 0447-ARSO00093-r
– Measurements have been performed in accordance with (report available on request):
– EN 300 328 V 1.8.1 (2012:06) (a)
– EN 301 489-17 V 2.2.1 (2012:09) (b)
– EN 301 489-1 V1.9.2 (2011:09) (c)
– EN60950-1:2006 +A12:2011 (d)
-CE certified:
P/N UMBLUETOOTHONE_WA Rev 20170628
26
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement